PROLINK WNR1008 Ver1.00 02.12.2010 PDF
PROLINK WNR1008 Ver1.00 02.12.2010 PDF
PROLINK WNR1008 Ver1.00 02.12.2010 PDF
com
®
PROLiNK WNR1008
3.75G Wireless-N 4-Port Gigabit Router
User’s Manual
Version 1.00
(English)
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes
or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
CAUTION:
1. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm
must be maintained between the antenna of this device and all persons.
2. This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter
TABLE OF CONTENT
CHAPTER 5: TROUBLESHOOTING................................................................................................................. 43
5.1. Overview................................................................................................................................................................................................................. 43
5.2. General Problems ............................................................................................................................................................................................... 43
5.3. Internet Access .................................................................................................................................................................................................... 43
5.4. Wireless Access ................................................................................................................................................................................................... 44
CHAPTER 1: INTRODUCTION
The PROLiNK® WNR1008 3.75G Wireless-N 4-Port Gigabit Router supports 4 ports 10/100/1000M Ethernet for
LAN and 1 port 10/100/1000M Ethernet interface for WAN. With the advanced MIMO technology, it can support the
data transmission rate 6 times more (up to 300 Mbps) and the coverage 3 times more than IEEE 802.11b/g devices.
The Wireless Router enables your whole network sharing a high-speed cable or DSL Internet connection. With it, you
can share a high-speed Internet connection, files, printers, and multi-player games at incredible speeds, without the
hassle of stringing wires. It also offers easy configuration for your wireless network at home and presents wireless
network of high functionality, security, and flexibility.
1.1.
Support 4 ports 10/100/1000M Ethernet for LAN and 1 port 10/100/1000M Ethernet interface for WAN.
Clock rate up to 600MHz.
Support the IEEE 802.11n/b/g standard, high speed data rate up to 300Mbps, two transmit and two receive
path (2T2R)
High security with build-in Security: WEP 64/128, WPA, WPA2, 802.1x and 802.11i.
Supports 1 additional USB port.
Supports WPS (Wi-Fi Protected Setup) with physical push button.
High security with build-in Security: WEP 64/128, WPA, WPA2, 802.1x and 802.11i.
Support Client, AP, WDS, AP+WDS mode.
Advanced Quality of Service (QoS), WMM.
Easy web browser configuration for home user setup.
Support USB Network attached storage (NAS) and media share function.
1.2.
LED Behavior
LED Printed Color Behavior Indication
ON Power on
Power PWR Green
OFF Power off
ON System is ready to login web server
System SYS Green OFF System is not ready to login web server
Blinking System is set to factory default
ON Internet link / active
Internet WAN Green OFF Internet function off
Blinking Internet traffic transmitting
Ant. 1
Install the appending antennas here.
Ant. 2
Press 2 seconds, the LED will be off.
Keep on pressing reset button 2~5 seconds, the system will reboot automatically.
Reset
Keep on pressing the reset button more than 5 seconds, the Wireless Router will set all setting back to factory
default.
Use standard LAN cables (RJ45 connectors) to connect your PCs to this port. If required, any port can be connected to
LAN 1-4
another hub. Any LAN port will automatically function as an "Uplink" port when necessary.
Connect the ADSL or Cable Modem here with RJ45 cable. If your modem came with a cable, use the supplied cable,
WAN
otherwise, use a standard LAN cable (RJ45 connectors).
DC 12V Connect the supplied power adapter here.
Left-sideview
To enable the WPS function press the physical WPS button on the Wireless Router once, then the LED will start to flash.
WPS
Please make a connection with other WPS supported device within 2 minutes.
Right-sideview
USB Insert the USB 3.5G card that provided by your ISP (Internet Service Provider) or USB network attached storage here.
2.1.
You have to MANUALLY switch the bar into the mode you preferred, Router, AP or Converter modes, then the device
will reboot automatically into the mode you have selected.
2.2.
In this mode, the device is supposed to connect to internet via ADSL/Cable Modem. The NAT is enabled and PCs in
LAN ports share the same IP address to ISP (Internet Service Provider) through WAN port. The connection type can be
setup in PPPoE, DHCP client, PPTP client, L2TP client or static IP.
The wireless connection will be set up from a point-to-point LAN into a point-to-multipoint WAN. This device
connects all the stations (PC or notebook with wireless function) to a wireless network. All stations can have the
Internet access if only the device has the Internet connection.
2.3.
When acting as an Access Point (AP), this device connects all the stations (PC/notebook with wireless network adapter)
to a wireless network. All stations can have the Internet access if only the Access Point has the Internet connection.
2.4.
If set to Converter mode, a device connects to each other through an access point or a base station (gateway or router.)
This device can work like a wireless station when it’s connected to a computer directly, so that the computer can send
packets from wired end to wireless interface.
CHAPTER 3: CONFIGURATION
3.1.
Step 1. Connect one end of the Ethernet cable to the LAN port (1~4) of the Wireless Router, another end to your PC
or notebook.
Step 2. There are two connection methods to connect to Internet (Only one can be used):
2-1. Connect Ethernet cable one end to the WAN (Internet) port of the Wireless Router, the other end to
the ADSL or cable modem.
2-2. Or you can insert 3.5G USB card (that provide by your ISP) into USB port.
3.2.
1. Start your computer and make sure the connection by an Ethernet cable between your computer and the Wireless
Router.
The Wireless Router is properly installed, LAN connection is OK, and it is powered ON. You can test the connection
by using the "Ping" command:
Please go to Start>Run…> Enter “cmd” command in the column to open the MS-DOS window.
If no response is received, either the connection is not working, or your PC's IP address is not compatible with the
Wireless Router's IP Address. (See next item.)
If your PC is using a fixed IP Address, its IP Address must be within the range 192.168.123.1 to 192.168.123.253 to
be compatible with the Wireless Router's default IP Address of 192.168.123.253. Also, the Network Mask must be
set to 255.255.255.0. See Chapter 4 - PC Configuration for details on checking your PC's TCP/IP settings.
Ensure that your PC and the Wireless Router are on the same network segment. (If you don't have a router, this
must be the case.)
Ensure you are using the wired LAN interface. The Wireless interface can only be used if its configuration matches
your PC's wireless settings.
The Internet connection type is according to the ISP (Internet Service Provider) that you selected or subscribed.
Usually, none.
However, some ISP's may
Your IP address is allocated automatically, when you
Dynamic IP address require you to use a particular
connect to you ISP.
Hostname, Domain name, or
MAC (physical) address.
Cable Modem
IP address allocated to you.
Some ISP's may also require you
Static (Fixed) IP address Your ISP allocates a permanent IP address to you. to use a particular Hostname,
Domain name, or MAC
(physical) address.
DSL Modem Static (Fixed) IP address Your ISP allocates a permanent IP address to you. IP address allocated to you.
3.3.
PROLiNK_WNR1008
3.4.
192.168.123.100
255.255.255.0
192.168.123.254
192.168.123.100 192.168.123.200
IP Address Shows the IP address of the Wireless Router (Default IP address is 192.168.123.254)
Subnet Mask The subnet mask of the Wireless Router (Default subnet mask is 255.255.255.0.)
Disable: Select to disable this Wireless Router to distribute IP addresses to connected clients.
Server: Select to enable this Wireless Router to distribute IP addresses (DHCP Server) to connected clients. And the
DHCP Mode
following field will be activated for you to enter the starting IP address.
Client: Select the client mode to use the
The starting address of this local IP network address pool. The pool is a piece of continuous IP address segment, the
device will distribute IP addresses from 192.168.123.100 to 192.168.123.200 to all the computers in the network that
request IP addresses from DHCP server (Router). The end IP address maximum is 253.
Note: If “Continuous IP address pool starts” is set at 192.168.123.1 and the “Number of IP address in pool end” is
253, the device will distribute IP addresses from 192.168.123.100 to 192.168.123.253 to all the computers in the
network that request IP addresses from DHCP server (Router).
Click Show Client button to show Active DHCP Client Table. The table shows assigned IP address, MAC address
and time expired for each client.
192.168.123.100
IP Address: Enter the fixed IP address that DHCP Server assigned to a certain connected station.
MAC Address: Enter the MAC address of a certain station, and then the DHCP Server will to distribute a fixed IP
address to the station automatically once they connected.
Comment: You can enter a comment to description above IP address or MAC address.
Apply Changes: After completing the settings on this page, click Apply changes button to save the settings.
Reset: Click Reset to restore to default values.
Static DHCP List: Here shows the static IP addresses that have been assigned according to the MAC address.
Delete Selected: Click Delete Selected to delete items which are selected.
Delete All: Click Delete All button to delete all the items.
Reset: Click Reset button to rest.
Clone MAC Address This table displays you the station MAC information.
DHCP Client
If the DHCP Client be selected, the computer will obtain the IP address automatically.
Hostname: Enter the hostname that assigned IP address to your computer in this field. Maximum input is 32
alphanumeric characters (case sensitive).
MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size, the default
value is 1492 for your application. Reducing the packet size can help connecting to certain web sites or speeding up
packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites.
Select to Attain DNS Automatically or select Set DNS Manually to set the DNS server IP address at the following
DNS 1~3 columns. Default setting is Attain DNS Automatically.
DNS 1: Enter the DNS server IP address (es) provided by your ISP, or you can specify your own preferred DNS server
IP address (es).
DNS 2~3: This servers are optional. You can enter another DNS server’s IP address as a backup. DNS 2 and 3 servers
will be used when the DNS 1 server fails.
If the Static IP be selected, user have to set up the IP address, subnet mask and default gateway according to the ISP
(Internet Service Provider) that provide the related information.
Default Gateway: Enter the default gateway IP address provided by your ISP here.
MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size, the default
value is 1492 for your application. Reducing the packet size can help connecting to certain web sites or speeding up
packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites.
Select to Attain DNS Automatically or select Set DNS Manually to set the DNS server IP address at the following
DNS 1~3 columns. Default setting is Attain DNS Automatically.
DNS 1: Enter the DNS server IP address (es) provided by your ISP, or you can specify your own preferred DNS server
IP address (es).
DNS 2~3: This servers are optional. You can enter another DNS server’s IP address as a backup. DNS 2 and 3 servers
PPPoE
If the PPPoE be selected, user have to set up the user name and password according to the ISP (Internet Service
Provider) that provided the related information.
PPPoE Type: Select the PPPoE types, Normal PPPoE, Multiple PPPoE and Unnumbered PPPoE form the pull-down
menu.
Multi-PPPoE provider: If user select Multiple PPPoE type, user have to setup the PPPoE provider here. Select Flets
West, Next West, Flets East, and Flets Next from the pull-down menu.
Public Range: If user selected Unnumbered PPPoE type, have to setup the range here.
User Name: Enter the username that provide by your ISP (Internet Service Provider). Maximum input is 32
alphanumeric characters (case sensitive).
Password: Enter the password that provide by your ISP. Maximum input is 32 alphanumeric characters (case-
sensitive).
Connection Type: Select the connection type Continuous, Connect on Demand or Manual from the pull-down
menu. If selected Manual user can click Connect button to make a connection.
Idle Time: It represents that the device will idle after the minutes you set. The time must be set between 1~1000
minutes. Default value of idle time is 5 minutes. This function will be available when the Connection Type is selected
to Connect on Demand.
MTU Size: MTU (Maximum Transmission Unit, namely the maximum packet size) for your application. Reducing the
packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect selection is
entered, you may not be able to open certain web sites.
Connection Type: Select the connection type Continuous, Connect on Demand or Manual from the pull-down
menu. If selected Manual user can click Connect button to make a connection.
Idle Time: It represents that the device will idle after the minutes you set. The time must be set between 1~1000
minutes. Default value of idle time is 5 minutes. This function will be available when the Connection Type is selected
to Connect on Demand.
Mobile Networks
User have to insert USB card that provide by Internet service provider into the USB port of the wireless router
first, therefore, the Mobile networks function can be used.
Auto APN: APN (Access Point Name.) If this function be selected, the system will auto detect the mobile network
setting via the USB that provide by the Internet service provider (ISP). To use the default settings is recommend.
Service Name: Keep the default setting or enter the service name that ISP provided.
Dial Number: Keep the default setting or enter the dial number that ISP provided.
Pin code: Keep the default setting or enter the SIM card Pin code that ISP provided.
Connection Type: Select the connection type Continuous, Connect on Demand from the pull-down menu.
Idle Time: It represents that the device will idle after the minutes you set. The time must be set between 1~1000
minutes. Default value of idle time is 5 minutes. This function will be available when the Connection Type is selected
to Connect on Demand.
MTU Size: MTU (Maximum Transmission Unit, namely the maximum packet size) for your application. Reducing the
packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect selection is
entered, you may not be able to open certain web sites.
Advanced Routing
If you connect several routers with this Wireless Router, you may need to set up a predefined routing rule to have
more effective network topology/traffic, this is called static route between those routers and the Wireless Router.
PPTP Server
Password Setup the password in the column, when the PPTP client try to connect to the PPTP sever should login with the
password.
PPTP Server IP
Setup the PPTP server IP address here.
address
Max Connect Users Setup the PPTP client allowed maximum here.
3.5.
Basic
PROLiNK_WNR1008
Advanced
Security
PROLiNK_WNR1008
Select SSID Select SSID (Service Set Identifier) to set up the security form the pull-down list.
Encryption There are several type of encryption modes including Disabled, WEP (Open System), WEP (Shared
Key), WEP ( AUTO), WPA (Personal), WPA2 (Personal), and WPA-Mixed. The security default setting
is Disabled. It is strongly recommended to set up security mode to prevent any unauthorized accessing.
Note:
AUTO (Open/Shared) means AP can accept client (station) to connect to it by using OPEN-WEP or
SHARED-WEP.
WEP
ACL
Delete Selected Click Delete Selected to delete items which are selected.
WDS
Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this,
you must set these APs in the same channel and set MAC address of other APs which you want to communicate with
in the table and then enable the WDS.
Note: To setup WDS must use the same wireless products (the same model will be better); due to
different wireless products might support different WDS settings. Thus, it is suggested that to use
the same wireless products that support WDS function.
Step 1. Users would like to set up the WDS function, please go to Wireless > Basic page to set up the mode into
WDS or AP+ WDS (Repeater) mode, and set the APs into the same Network Name (SSID) and Channel (If
set to WDS mode, the SSID do not need to change). After setting up, please click Apply Changes button to
execute.
2 PROLiNK_WNR1008
Step 2. Then go to Wireless > WDS page to (1) enable the WDS function and (2) enter APs Wireless MAC address
(please go to Status> Wireless Configuration to make sure the BSSID) to each other to make the WDS
connection. Please click Apply button to execute.
MAC Address: Enter the Wireless BSSID (MAC) 12 characters of the wireless AP that you want to connect with. To
MAC Address check your wireless router’s MAC address, please go to Status > Wireless Configuration to find your BSSID
(Wireless MAC address.)
PROLiNK_WNR1008
Data Rate Select the data rate form the pull-down list.
Comment Enter a description for the device.
Apply Changes After completing the settings on this page, click Apply changes button to save the settings.
Reset Click Reset to restore to default values.
Enable the WDS function and then click Set Security button to set up the WDS security.
Set Security Encryption: Select the encryption type None, WEP 64 bits, WEP 128 bits, and WPA2 (AES) from the pull-down
menu.
WEP Key Format: For WEP 64 bits and WEP 128 bits encryption type, the selection of WEP Key Format are Hex
and ASCII.
WEP Key: If select Hex if you are using hexadecimal numbers (0-9, or A-F). Select ASCII if you are using ASCII
characters (case-sensitive).
Hexadecimal (WEP 64 bits): 10 Hex characters (0~9, a~f).
Hexadecimal (WEP 128 bits): 26 Hex characters (0~9, a~f).
ASCII (WEP 64 bits): 5 ASCII characters (case-sensitive).
ASCII (WEP 128 bits): 13 ASCII characters (case-sensitive).
Pre-Shared Key Format: The Pre-shared Key Format will be enabled when WPA (TKIP) and WPA2 (AES)
encryption be selected. There are two formats for choice to set the Pre-shared key, Passphrase and Hex (64
characters). If Hex is selected, users will have to enter a 64 characters string. For easier configuration, the
Passphrase (at least 8 characters) format is recommended.
Pre-Shared Key: Pre-Shared-Key serves as a password. Users may key in 8 to 63 characters string to set the
passwords or leave it blank, in which the 802.1x Authentication will be activated. Make sure the same password is
used on client's end.
Click to show the current WDS AP table. This table shows the MAC address, transmission packets and errors,
reception packets and Tx Rate (Mbps) counters for each configured WDS AP.
Show Statistics
WPS
Schedule
3.6.
DMZ Settings
MAC Filtering
IP Filtering
Virtual Server
VLAN
3.7.
Password
name and password will disable the protection. It’s strongly recommended to assign a set of password for further
security.
New Password To set up the login password to protect the Wireless Router configuration accessing via web browser. Maximum
input is 30 alphanumeric characters (case sensitive.)
Confirmed Password Key in the password again to confirm.
NAS
Media Share
NTP
Password/Key Enter your passwords that you registered in service provider website. Maximum input is 30 alphanumeric characters
(case sensitive).
Apply Changes After completing the settings on this page, click Apply Changes button to save the settings.
Reset Click Reset button to restore to default values.
Upgrade Firmware
Settings Management
Statistics
This page shows the packet counters for transmission and reception regarding to wireless and Ethernet networks.
System Log
Reboot
Click the Reboot button to restart the Wireless Router.
CHAPTER 4: PC CONFIGURATION
4.1.
4.2.
This section describes how to configure Windows clients for Internet access via the Wireless Router.
The first step is to check the PC's TCP/IP settings.
The Wireless Router uses the TCP/IP network protocol for all functions, so it is essential that the TCP/IP
protocol be installed and configured on each PC.
If using default Wireless Router settings, and default Windows TCP/IP settings, no changes need to be made.
By default, the Wireless Router will act as a DHCP Server, automatically providing a suitable IP address (and
related information) to each PC when the PC boots.
For all non-server versions of Windows, the default TCP/IP setting is to act as a DHCP client.
4. Click on the Properties button. You should then see a screen like
the following.
1. Go to Start Control Panel Network and Internet Network and Sharing Center Manage Network
Connections Local Area Connection.
2. Right click the Local Area Connection icon and choose Properties. You should see a screen like the following:
3. Select the Internet Protocol Version 4 (TCP/IPv4) or 6 (TCP/IPv6)
for your network card
1. Go to Start Control Panel Network and Sharing Center Manage Network Connections Local Area
Connection.
2. Right click the Local Area Connection icon and choose Properties. You should see a screen like the following:
3. Select the Internet Protocol Version 4 (TCP/IPv4) or 6 (TCP/IPv6)
for your network card.
4. Click on the Properties button. You should then see a screen like
the following.
Internet Access
To configure your PCs to use the Wireless Router for Internet access:
Ensure that the ADSL modem, DSL modem, Cable modem, or other permanent connection is functional.
Use the following procedure to configure your Browser to access the Internet via the LAN, rather than by a
Dial-up connection.
For Windows XP
1. Select Start menu Control Panel Network and Internet Connections.
2. Select Set up or change your Internet Connection.
3. Select the Connection tab, and click the Setup button.
For Windows 7
1. Select Start menu Control Panel Network Sharing Center.
2. Select Set up a new connection or network.
3. Select Connect to the Internet and click Next to continue.
4. Select Broadband (PPPoE).
5. Enter User name and Password that provided by the ISP, then click Connect to make a connection.
Accessing AOL
To access AOL (America On Line) through the Wireless Router, the AOL for Windows software must be configured to
use TCP/IP network access, rather than a dial-up connection. The configuration process is as follows:
1. Start the AOL for Windows communication software. Ensure that it is Version 2.5, 3.0 or later. This procedure
will not work with earlier versions.
2. Click the Setup button.
3. Select Create Location, and change the location name from "New Locality" to " Wireless Router ".
4. Click Edit Location. Select TCP/IP for the Network field. (Leave the Phone Number blank.)
5. Click Save, then OK.
6. Configuration is now complete.
7. Before clicking "Sign On", always ensure that you are using the " Wireless Router " location.
4.3.
From your Macintosh, you can access the Internet via the Wireless Router. The procedure is as follows.
1. Open the TCP/IP Control Panel.
2. Select Ethernet from the Connect via pop-up menu.
3. Select Using DHCP Server from the Configure pop-up menu. The DHCP Client ID field can be left blank.
4. Close the TCP/IP panel, saving your settings.
If using manually assigned IP addresses instead of DHCP, the required changes are:
Set the Router Address field to the Wireless Router's IP Address.
Ensure your DNS settings are correct.
4.4.
To access the Internet via the Wireless Router, it is only necessary to set the Wireless Router as the "Gateway".
Ensure you are logged in as "root" before attempting any changes.
Fixed IP Address
By default, most Unix installations use a fixed IP Address. If you wish to continue using a fixed IP Address, make the
following changes to your configuration.
Set your "Default Gateway" to the IP Address of the Wireless Router.
Ensure your DNS (Domain Name server) settings are correct.
4.5.
4.6.
This section applies to all wireless stations (client end) wishing to use the Wireless Router as an access point,
regardless of the operating system that is used on the client.
To use the Wireless Router, each wireless station must have compatible settings, as following:
SSID (ESSID) (Extended The network name must match the value used on the Wireless Router.
Service Set Identifier) Note! The SSID (service set identifier) is case- sensitive.
If there is no security is enabled on the Wireless Router, the security of each station should be disabled
Disable
as well. And, you can connect the Wireless Router without security, but it is NOT recommended.
If WEP is enabled on the Wireless Router, each station must use the same settings as the Wireless
Router.
Personal (Pre-Shared Key) WPA-PSK (TKIP/AES)/ WPA2-PSK (TKIP/AES): If one of these securities is enabled on the Wireless
Router. To make a connection, each station must use the same algorithms and pass phrase as the
WPA Wireless Router.
WPA2
Pre-Shared Key Format: There are two formats for choice to set the Pre-shared key, Passphrase and
WPA2-Mixed
Hex (64 characters). If Hex is selected, users will have to enter 64 characters string at a time. For easier
configuration, the Passphrase (at least 8 characters) format is recommended.
Pre-Shared Key : Pre-Shared Key serves as a password. Users may key in 8 to 63 characters string if
you selected passphrase. Pre-shared key format to set the passwords or leave it blank, in which the
802.1x Authentication will be activated. Make sure the same password is used on client's end.
Enterprise (RADIUS)
RADIUS Server: RADIUS is an authentication, authorization and accounting client-server protocol. The
WPA client is a Network Access Server that desires to authenticate its links. The RADIUS is a server that has
WPA2 access to a user database with authentication information. Each station must set up the RADIUS Server’s
WPA2-Mixed IP address, port and passwords that provided by your ISP.
802.1x
By default, the Wireless Router will allow 802.11b, 802.11g and 802.11n connections.
CHAPTER 5: TROUBLESHOOTING
5.1.
This chapter covers some common problems that may be encountered while using the Wireless Router and some
possible solutions to them. If you follow the suggested steps and the Wireless Router still does not function properly,
contact your dealer for further advice.
5.2.
Solution 1:
Check the following:
Check the Wireless Router is properly installed, LAN connections are OK, and it is powered ON.
Ensure that your PC and the Wireless Router are on the same network segment.
If your PC is set to "Obtain an IP address automatically" (DHCP client), please restart it.
If your PC uses a Fixed (Static) IP address, ensure that it is using an IP address within the range 192.168.123.1 to
192.168.123.253 and thus compatible with the Wireless Router's default IP Address of 192.168.123.254.
Also, the Network Mask should be set to 255.255.255.0 to match the Wireless Router.
In Windows, you can check these settings by using Control Panel-Network to check the Properties for the TCP/IP
protocol. You can check Chapter 4: PC Configuration- TCP/IP settings for reference.
5.3.
Solution 1:
A number of things could be causing this. Try the following troubleshooting steps.
Check if other PCs work. If they do, ensure that your PCs IP settings are correct. If using a Fixed (Static) IP address,
check the Network Mask, Default gateway and DNS as well as the IP address.
If the PCs are configured correctly, but still not working, check the Wireless Router. Ensure that it is connected and
ON. Connect to it and check its settings. (If you can't connect to it, check the LAN and power connections.)
If the Wireless Router is configured correctly, check your Internet connection (ADSL/Cable modem) to see that it is
working correctly.
Problem 2: Some applications do not run properly when using the Wireless Router.
Solution 2:
The Wireless Router processes the data passing through it, so it is not transparent.
Use the Filter Settings feature to allow the use of Internet applications, which do not function correctly.
If this does solve the problem you can use the DMZ function. This should work with almost every application, but:
5.4.
Solution 1:
Check the following:
Mode: Your PC is set to Infrastructure Mode. (Access Points are always in Infrastructure Mode)
SSID: The SSID (service set identifier) on your PC and the Wireless Router are the same.
Remember that the SSID (service set identifier) is case-sensitive. So, for example "Workgroup" does NOT match
"workgroup."
Security: Both your PC and the Wireless Router must have the same setting for security.
o Disabled: The default setting for the Wireless Router security is disabled, so your wireless station should
also has security disabled.
o Enabled: If security is enabled on the Wireless Router, your PC must have security enabled, and the key
must be matched.
o It's strongly suggest to set up security that could prevent any unauthorized accessing to your wireless
network. Setting WPA2 security is recommended that offers stronger security than WEP. Both your
computer and the Wireless Router must have the same settings for security.
Channel: The wireless local area network is activated and configured by default. If necessary, please check and match
channel for the terminal, for example, your notebook. Both your computer (client) and the Wireless Router must set
to the same channel for connection.
Solution 2:
The wireless system will connect at the highest possible speed, depending on the distance and the environment. To obtain the
highest possible connection speed, you can experiment with the following:
Wireless Router location: Try adjusting the location and orientation of the Wireless Router. To see if radio
interference is causing a problem, see if connection is possible when close to the Wireless Router. Remember that the
connection range can be as little as 100 feet in poor environments.
Wireless Channels: If interference is the problem, changing to another channel may show a well improvement.
Radio Interference: Other devices may be causing interference. You can try to turn off other wireless devices, and
see if this helps. Any "noisy" devices should be shielded or relocated.
RF Shielding: Your environment may tend to block transmission between the wireless stations. This will mean high
access speed is only possible when close to the Wireless Router.
6.1.
A group of wireless stations and a single access point, all using the same SSID (service set identifier), form a Basic
Service Set (BSS).
Using the same SSID (service set identifier) is essential. Devices with different SSIDs are unable to communicate with
each other.
6.2.
The wireless channel sets the radio frequency used for communication.
Access points use a fixed channel. You can select the channel used. This allows you to choose a channel which
provides the least interference and best performance. In the USA and Canada, 11 channels are available. If
using multiple access points, it is better if adjacent access points use different channels to reduce interference.
In "Infrastructure" mode, wireless stations normally scan all channels, looking for an access point. If more than
one access point can be used, the one with the strongest signal is used. (This can only happen within an ESS
(Extended Service Set)).
ESS: In Infrastructure mode, one or more BSS (Basic Service Set) can set up a ESS (Extended Service Set). User
can access and roaming BSS data and the access point should be set to the same ESSID (Extended Service Set
Identifier) to allow roaming.
6.3.
WEP
WEP (Wired Equivalent Privacy) is a standard for encrypting data before it is transmitted. This is desirable because it is
impossible to prevent snoopers from receiving any data which is transmitted by your wireless stations. But if the data
is encrypted, then it is meaningless unless the receiver can decrypt it.
If WEP is used, the wireless stations and the access point must have the same security settings for each of the
following:
WPA/ WPA2 (Wi-Fi Protected Access) is more secure than WEP. It uses a “Shared Key” which allows the encryption
keys to be regenerated at a specified interval. There are several encryption options: TKIP, AES, TKIP-AES and
additional setup for RADIUS is required in this method. The most important features beyond WPA to become
standardized through 802.11i/WPA2 are: pre-authentication, which enables secure fast roaming without noticeable
signal latency.
If WPA or WPA2 is used, the wireless stations and access point must have the same security settings.
802.1x
With 802.1x authentication, a wireless PC can join any network and receive any messages that are not encrypted,
however, additional setup for RADIUS to issue the WEP key dynamically will be required.
RADIUS is an authentication, authorization, and accounting client-server protocol. The client is a network access server
that desires to authenticate its links. The server has access to a user database with authentication information.
6.4.
To allow wireless stations (STA) to access the access point (AP), the wireless stations and the access point must use the
same settings, as follows:
SSID (ESSID) (Extended The network name must match the value used on the Wireless Router.
Service Set Identifier) Note! The SSID (service set identifier) is case- sensitive.
If there is no security is enabled on the Wireless Router, the security of each station should be disabled as well.
Disable
And, you can connect the Wireless Router without security, but it is NOT recommended.
If WEP is enabled on the Wireless Router, each station must use the same settings as the Wireless Router.
WPA-PSK (TKIP/AES)/ WPA2-PSK (TKIP/AES): If one of these securities is enabled on the Wireless Router. To make
a connection, each station must use the same algorithms and pass phrase as the Wireless Router.
Personal (Pre-Shared Key)
Pre-Shared Key Format: There are two formats for choice to set the Pre-shared key, Passphrase and Hex (64
WPA characters). If Hex is selected, users will have to enter 64 characters string at a time. For easier configuration, the
WPA2 Passphrase (at least 8 characters) format is recommended.
WPA2-Mixed
Pre-Shared Key: Pre-Shared Key serves as a password. Users may key in 8 to 63 characters string if you selected
passphrase. Pre-shared key format to set the passwords or leave it blank, in which the 802.1x authentication will
be activated. Make sure the same password is used on client's end.
Enterprise (RADIUS)
RADIUS Server: RADIUS is an authentication, authorization and accounting client-server protocol. The client is a
WPA network access server that desires to authenticate its links. The RADIUS is a server that has access to a user
WPA2 database with authentication information. Each station must set up the RADIUS server’s IP address, port and
WPA2-Mixed passwords that provided by your ISP.
802.1x
7.1.
7.2.
7.3.
SINGAPORE
FIDA INTERNATIHIDUPAL (S) PTE LTD
Block 16 Kallang Place, #06-02 Kallang Basin Industrial Estate, Singapataue 339156.
Tel : (65) 6357 0668
Email : support@fida.com
MALAYSIA
FIDA SYSTEMS (M) SDN BHD
29 Jalan USJ 1/31, 47600 Subang Jaya, Selangatau Darul Ehsan, Malaysia.
Tel : (60) 3 8024 9151
Email : support_my@fida.com
INDONESIA
PROLiNK INDONESIA
Jl. Cideng Barat No. 79, Jakarta Pusat 10150 - Indonesia.
Tel : (62) 21 3483 1777
Email : support@prolink.co.id
PROLiNK is a trademark of FIDA International (S) PTE LTD dan is manufactured under its authatauity. All other brdans, products, services, logos dan
company names mentioned herein are trademarks of their respective owners. All specifications, designs dan contents are subject to changes without
priatau notice. © Copyright 2010. PROLiNK all rights reserved.
www.prolink2u.com
®
PROLiNK WNR1008
3.75G Wireless-N 4-Port Gigabit Router
Buku Manual
Versi 1.00
(Indonesia)
PERNYATAAN KOMISI KOMUNIKASI FEDERAL INTERFERENSI
Peralatan ini telah diuji dan memenuhi batas untuk Kelas B perangkat digital, sesuai dengan Bagian 15 dari Peraturan
FCC. Batasan ini dirancang untuk memberikan perlindungan memadai terhadap gangguan yang membahayakan pada
insalasi rumah. Peralatan ini menghasilkan dan dapat memancarkan radio frekuensi energy da jika tidak terpasang dan
digunakan sesuai dengan petunjuk, dapat menyebabkan gangguan yang membahayakan pada komunikasi radio.
Namun, tidak ada jaminan bahwa inerferensi tidak akan terjadi pada instalasi tertentu. Jika peralatan ini menimbulan
interferensi pada penerima televise, yang dapat ditentukan dengan memutar peralatan off dan pada, pengguna
dianjurkan untuk mencoba memperbaiki interferensi tersebut dengan salah satu langkah-langkah berikut:
Arahkan atau posisikan kembali antena penerima.
Meningkatkan pemisahan antara peralatan dan penerima.
Hubungkan peralatan ke stopkontak pada sirkuit yang berbeda dari yang dimana penerima terhubung.
Tanyakan pada dealer atau teknisi radio / TV untuk bantuan.
FCC Perhatian: Perubahan atau modifikasi yang tidak disetujui oleh pihak bertanggung jawab atas kepatuhan dapat
membatalkan hak pengguna untuk mengoperasikan peralatan.
Perangkat ini memenuhi aturan Part 15 of the FCC. Pengoperasian tunduk pada dua kondisi sebagai berikut: (1)
perangkat ini tidak menimbulkan gangguan yang membahayakan, dan (2) perangkat ini harus menerima interferensi
yang diterima, termasuk interferensi yang dapat menyebabkan pengoperasian yang tidak diinginkan.
Buku Manual atau buku petunjuk secara disengaja atau tidak memperingatkan pengguna bahwa perubahan atau
modifikasi yang tidak disetujui oleh pihak yang bertanggung jawab atas kepatuhan dapat membatalkan kewenangan
pengguna untuk mengoperasikan peralatan
PERHATIAN:
1. Untuk memenuhi persyaratan kepatuhan pemaparan RF FCC, jarak pemisahan minimal 20 cm harus
dijaga antara antena perangkat ini dan semua atauang.
2. Transmitter ini tidak boleh terletak atau yang beroperasi dalam hubungannya dengan antena lain atau
pemancar.
DAFTAR ISI
BAGIAN 1: PENDAHULUAN
PROLiNK® WNR1008 3.75G Wireless-N 4-Port Gigabit Router mendukung 4 port Ethernet 10/100/1000M untuk
LAN dan 1 port 10/100/1000M interface Ethernet untuk WAN. Dengan teknologi MIMO, dapat mendukung kecepatan
transmisi data 6 kali lebih banyak (sampai dengan 300 Mbps) dan cakupan 3 kali lebih dari perangkat IEEE
802.11b/g. Router nirkabel memungkinkan seluruh jaringan Anda berbagi dengan berkecepatan tinggi atau koneksi
DSL internet. Dengan itu, Anda dapat berbagi koneksi internet berkecepatan tinggi, file, printer, dan game multi-player
dengan kecepatan yang luar biasa, tanpa harus repot merangkai kabel. Hal ini juga menawarkan konfigurasi yang
mudah untuk jaringan nirkabel Anda di rumah dan menyajikan jaringan nirkabel fungsionalitas tinggi, keamanan, dan
fleksibilitas
1.1.
Mendukung 4 ports 10/100/1000M Ethernet LAN dan 1 port 10/100/1000M Ethernet interface WAN.
Clock rate sampai dengan 600MHz.
Mendukung stdanard IEEE 802.11n/b/g, high speed data rate sampai dengan 300Mbps, two transmit dan two
receive path (2T2R)
Tingkat kemanan tinggi dengan build-in Security: WEP 64/128, WPA, WPA2, 802.1x dan 802.11i.
Mendukung 1 USB port tambahan.
Mendukung WPS (Wi-Fi Protected Setup) dengan tombol fisik.
Mendukung Modus Client, AP, WDS, AP+WDS.
Advanced Quality of Service (QoS), WMM.
Konfigurasi web browser yang mudah untuk pengguna rumah.
Mendukung USB Network attached storage (NAS) dan fungsi media share.
1.2.
Perilaku LED
LED Tercetak Warna Perilaku Indikasi
HIDUP Power Hidup
Power PWR Hijau
MATI Power Mati
HIDUP System siap untuk masuk ke web server
System SYS Hijau MATI System belum iap masuk ke web server
Berkedip System kembali ke pengaturan default
HIDUP Internet Aktif
Internet WAN Hijau MATI Internet Tidak Aktif
Berkedip Data Transmit
Ant. 1
Tempat pemasangan Antena
Ant. 2
Gunakan stdanar kabel LAN (RJ45) untuk koneksi dari PC Anda. Jika diperlukan, semua port dapat dihubungkan ke
LAN 1-4
switch/hub.
WPS
Untuk mengaktifkan fungsi WPS, tekan tombol WPS pada Wireless Router lalu lampu LED akan mulai berkedip. Silahkan
WPS
untuk membuat koneksi dengan perangkat lainya yang mendukung fungsi WPS selama 2 menit.
Right-sideview
2.1.
You have to MANUALLY switch the bar into the mode you preferred, Router, AP atau Modus Converters, then the
device will reboot automatically into the mode you have selected.
Anda harus SECARA MANUAL menswitch bar untuk beralih ke modus yang Anda sukai, Router, AP atau Modus
Converter, maka perangkat akan reboot otomatis ke mode yang telah Anda pilih.
2.2.
Dalam mode ini, perangkat seharusnya terhubung ke internet melalui ADSL / Cable Modem. NAT ini diaktifkan dan PC
dalam LAN port dapat berbagi alamat IP yang sama untuk ISP (Internet Service Provider) melalui port WAN. Jenis
sambungan dapat setup di PPPoE, DHCP client, PPTP client, L2TP client atau IP statis.
Sambungan nirkabel akan dibentuk dari LAN point-to-point menjadi point-to-multipoint WAN. Perangkat ini
menghubungkan semua stasiun (PC atau notebook dengan fungsi nirkabel) ke jaringan nirkabel. Semua stasiun dapat
memiliki Akses Internet jika hanya perangkat memiliki koneksi internet.
2.3.
Ketika bertindak sebagai Access Point (AP), perangkat ini menghubungkan semua stasiun (PC / notebook dengan
adaptatau jaringan nirkabel) ke jaringan nirkabel. Semua stasiun dapat memiliki Akses Internet jika hanya Access Point
memiliki koneksi internet.
2.4.
If set to Modus Converter, a device connects to each other through an access point atau a base station (gateway atau
router.) This device can work like a wireless station when it’s connected to a computer directly, so that the computer
can send packets from wired end to wireless interface.
Jika diatur ke Modus Converter, perangkat akan terhubungkan satu sama lain melalui jalur akses atau base station
(gateway atau router.) Perangkat ini dapat bekerja seperti stasiun nirkabel saat itu terhubung ke komputer secara
langsung, sehingga komputer dapat mengirimkan paket dari ujung kabel ke antarmuka nirkabel
BAGIAN 3: KONFIGURSI
3.1.
Step 1. Sambungkan salah satu ujung kabel Ethernet ke port LAN (1~4) dari Wireless Router, ujung yang lain ke PC
atau notebook Anda.
Step 2. Ada 2 metode untuk dapat terhubung ke Internet (Hanya satu yang dapat digunakan):
2-1. Sambungkan kabel Ethernet ke port WAN (Internet) dari Wireless Router, ujung yang lain ke port ADSL
atau cable modem.
2-2. Or Anda dapat menggunakan 3.5G USB card (yang disediakan oleh provider) ke USB port.
3.2.
1. Jalankan computer Anda dan pastikan Anda menggunakan kabel Ethernet untuk berkomunikasi dengan Wireless
Router.
Wireless Router sudah terinstall dengan benar, koneksi LAN OK, dan powered menyala. Anda dapat melakukan uji
koneksi dengan penggunakan perintah "ping":
Silahkan ke Start>Run…> Ketik “cmd” maka akan muncul MS-DOS prompt.
Jika tidak ada respon yang diterima, atau your alamat IP pada PC Anda tida sesuai dengan alamat IP dari Wireless
Router. (Lihat instruksi berikut.)
Jika PC Anda menggunakan alamat IP statis, alamat IP harus berada antara 192.168.123.1 sampai 192.168.123.253
untuk dapat berkomunikasi dengan Wireless Router. Juga, Network Mask harus di set ke 255.255.255.0. Lihat
BAGIAN 4 - KONFIGURASI PC untuk detail pengaturan TCP/IP.
Pastikan PC dan Wireless Router Anda berada pada network segment yang sama. (Jika tidak Anda tidak memiliki
router, ini yang akan terjadi.)
Pastikan Anda menggunakan koneksi kabel LAN. Koneksi Wireless hanya dapat digunakan apabila pengaturan
pada PC Anda sudah sama dengan pengaturan pada wireless.
Jenis koneksi The Internet berdasarkan ISP (Internet Service Provider) yang dapat Anda gunakan.
3.3.
PROLiNK_WNR1008
3.4.
192.168.123.100
255.255.255.0
192.168.123.254
192.168.123.100 192.168.123.200
IP Address Menampilkan alamat IP dari Wireless Router (Alamat Default IP adalah 192.168.123.254)
Subnet Mask Subnet mask dari Wireless Router (Default subnet mask adalah 255.255.255.0.)
Disable: Pilih untuk menonaktifkan Router Wireless untuk mendistribusikan alamat IP ke klien yang terhubung.
Server: Pilih untuk mengaktifkan Router Wireless untuk mendistribusikan alamat IP (DHCP Server) untuk klien yang
DHCP Mode
terhubung. Dan kolom berikut akan diaktifkan bagi Anda untuk memasukkan alamat IP awal
Client: Pilih mode client untuk menggunakan
Alamat awal dari kumpulan jaringan alamat IP lokal. Pool adalah bagian dari segmen alamat IP, perangkat akan
mendistribusikan alamat IP dari 192.168.123.100 sampai 192.168.123.200 ke semua komputer dalam jaringan yang
permintaan alamat IP dari server DHCP (Router). Maksimum alamat akhir IP adalah 253.
Catatan: Jika " alamat IP Continuous" yang ditetapkan mulai dari 192.168.123.1 dan "Jumlah alamat IP pada akhir
pool" adalah 253, perangkat akan mendistribusikan alamat IP dari 192.168.123.100 sampai 192.168.123.253 ke semua
komputer dalam jaringan yang permintaan alamat IP dari server DHCP (Router).
Klik tombol Show Client untuk menampilkan Active DHCP Client Table. Tabel menampilkan alamat IP yang
ditetapkan, alamat MAC dan waktu kadarluarsa untuk setiap client.
192.168.123.100
Centang kotak untuk mengaktifkan fungsi Static DHCP, pengaturan default adalah tidak aktif. Bila diaktifkan,
pengguna dapat meng Klik tombol Set Static DHCP untuk mengatur fungsi Static DHCP
Static DHCP
IP Address: Masukkan alamat IP statis untuk penggunaan alamat yang disediakan oleh DHCP Server.
MAC Address: Masukkan alamat MAC untuk setiap station, lalu DHCP Server akan mendistribusikan alamat IP statis
ke semua station secaa otomatis ketika terhubung.
Comment: Anda dapat memasukkan komentar untuk alamat IP atau alamat MAC.
Apply Changes: Setelah selesai melakukan pengaturan, Klik tombol Apply changes untuk menyimpan.
Reset: Klik Reset untuk mengembalikan pengaturan sebelumnya.
Static DHCP List: Menampilkn alamat IP statis yang telah ditetapkan berdasarkan alamat MAC.
Delete Selected: Klik Delete Selected untuk menghapus item.
Delete All: Klik tombol Delete All untuk menghapus semua item.
Clone MAC Address Tabel ini menampilkan informasi MAC.
DHCP Client
Jika DHCP Client yang dipilih, router akan memperoleh alamat IP secara otomatis.
Hostname: Masukkan hostname untuk menetapkan alamat IP ke computer Anda. Maximum 32 alphanumeric
karakter (case sensitive).
MTU Size: MTU (Maximum Transmission Unit), nilai default adalah 1492 untuk aplikasi Anda. Mengurangi ukuran
paket dapat membantu menghubungkan ke situs web tertentu atau mempercepat laju paket transfer. Jika ukuran
paket salah dimasukkan, Anda mungkin tidak dapat membuka situs web tertentu.
Pilih Attain DNS Automatically atau pilih Set DNS Manually untuk menset alamat IP dari DNS server. Pengaturan
Default adalah Attain DNS Automatically.
DNS 1: Masukkan alamat IP untuk DNS server yang disediakan oleh ISP, atau Anda dapat mengisi alamat IP yang
Anda tahu pada kolom preferred DNS server .
DNS 2~3: Kolom ini adalah opsi. Anda juga dapat mengisi alamat IP pada kolom ini. DNS 2 dan 3 servers akan
terpakai bila DNS 1 server gagal.
Jika alamat IP statis dipilih, pengguna harus menetapkan alamat IP, subnet mask dan default gateway yang didapat
dari ISP (Internet Service Provider).
Default Gateway: Masukan alamat IP untuk default gateway yang disediakan oleh ISP.
MTU Size: MTU (Maximum Transmission Unit), nilai default adalah 1492 untuk aplikasi Anda. Mengurangi ukuran
paket dapat membantu menghubungkan ke situs web tertentu atau mempercepat laju paket transfer. Jika ukuran
paket salah dimasukkan, Anda mungkin tidak dapat membuka situs web tertentu.
Pilih Attain DNS Automatically atau pilih Set DNS Manually untuk menset alamat IP dari DNS server. Pengaturan
Default adalah Attain DNS Automatically.
DNS 1: Masukkan alamat IP untuk DNS server yang disediakan oleh ISP, atau Anda dapat mengisi alamat IP yang
Anda tahu pada kolom preferred DNS server .
DNS 2~3: Kolom ini adalah opsi. Anda juga dapat mengisi alamat IP pada kolom ini. DNS 2 dan 3 servers akan
terpakai bila DNS 1 server gagal.will be used when the DNS 1 server fails.
PPPoE
Jika PPPoE yang dipilih, pengguna harus mengisi user name dan password yang disediakan oleh ISP.
PPPoE Type: Pilih jenis PPPoE, Nataumal PPPoE, Multiple PPPoE dan Unnumbered PPPoE dari menu pull-down.
Multi-PPPoE provider: Jika pengguna memilih jenis Multiple PPPoE, pengguna harus mengisi PPPoE disini. Pilih
Flets West, Next West, Flets East, dan Flets Next dari menu pull-down.
Public Range: Jika pengguna memilih jenis Unnumbered PPPoE, harus mengisi range disini.
User Name: Masukkan username yang disediakan oleh ISP (Internet Service Provider). Maximum input 32
alphanumeric karakter case sensitive).
Password: Masukkan password yang disediakan oleh ISP. Maximum input 32 alphanumeric karakter (case-sensitive).
Connection Type: Pilih jenis koneksi Continuous, Connect on Demdan atau Manual dari menu pull-down. Jika
memilih Manual pengguna dapat meng Klik tombol Connect untuk melakukan koneksi.
Idle Time: Menampilkan perangkat diam setelah waktu yang Anda tentukan. Pengaturan waktu antara 1~1000 menit.
Nilai Default adalah 5 menit. Fungsi ini tersedia jika Connection Type yang digunakan adalah Connection Demdan.
MTU Size: MTU (Maximum Transmission Unit), nilai default adalah 1492 untuk aplikasi Anda. Mengurangi ukuran
paket dapat membantu menghubungkan ke situs web tertentu atau mempercepat laju paket transfer. Jika ukuran
paket salah dimasukkan, Anda mungkin tidak dapat membuka situs web tertentu.
Mobile Networks
Pengguna harus menyisipkan USB card yang disediakan oleh provider ke dalam port USB pada wireless router
untuk dapat menggunakan fungsi Mobile networks.
Auto APN: APN (Access Point Name.) Jika fungsi ini dipilih, system akan mendeteksi secara otomatis pengaturan
mobile network melalui USB yang disediakan oleh Internet service provider (ISP). Menggunakan pengaturan default
sangat direkomendasi.
Service Name: Gunakan pengaturan default atau masukkan nama service yang disediakan oleh ISP.
Dial Number: Gunakan pengaturan default atau masukkan nomatau dial yang disediakan oleh ISP.
Pin code: Gunakan pengaturan default atau masukkan SIM card Pin code yang disediakan oleh ISP.
Connection Type: Pilih jenis koneksi Continuous, Connect on Demdan dari menu pull-down.
Idle Time: Menampilkan perangkat diam setelah waktu yang Anda tentukan. Pengaturan waktu antara 1~1000 menit.
Nilai Default adalah 5 menit. Fungsi ini tersedia jika Connection Type yang digunakan adalah Connection Demdan.
MTU Size: MTU (Maximum Transmission Unit), nilai default adalah 1492 untuk aplikasi Anda. Mengurangi ukuran
paket dapat membantu menghubungkan ke situs web tertentu atau mempercepat laju paket transfer. Jika ukuran
paket salah dimasukkan, Anda mungkin tidak dapat membuka situs web tertentu.
Advanced Routing
Jika Anda menghubungkan beberapa router dengan Wireless Router, Anda mungkin perlu mengatur aturan routing
yang telah ditetapkan agar lalu lintas data lebih efektif yang disebut rute statis antara router dan Wireless Router.
PPTP Server
Password Masukkan password, ketika PPTP client mencoba untuk terhubung ke PPTP sever akan menggunakan password ini.
PPTP Server IP
Masukkan alamat IP dari PPTP server.
address
Max Connect Users Masukkan jumlah maksimum akses oleh PPTP client.
3.5.
Basic
PROLiNK_WNR1008
Multiple APs
Pada halaman ini menampilkan dan update pengaturan nirkabel untuk multiple APs.
Advanced
Security
PROLiNK_WNR1008
Pilih SSID Pilih SSID (Service Set Identifier) untuk membuat pengaturan security pada menu pull-down.
Encryption Ada beberapa jenis modus encryption termasuk Disabled, WEP (Open System), WEP (Shared Key), WEP ( AUTO), WPA
(Personal), WPA2 (Personal), dan WPA-Mixed. Pengaturan default security adalah Disabled. Sangat direkomendasikan
untuk menggunakan modus security untuk mencegah pengguna yang tidak dikenal.
Catatan:
AUTO (Open/Shared) berarti AP dapat menerima client untuk terhubung menggunakan OPEN-WEP atau SHARED-WEP.
WEP
Authentication Mode: Pilih Enterprise (RADIUS) atau Modus Personal (Pre-Shared Key).
WPA Cipher Suite: ini mendukung AES saja.
WPA2 Cipher Suite: ini mendukung AES saja.
Pre-Shared Key Format: Memiliki pilihan untuk set Pre-shared key, Passphrase dan Hex (64 karakters). Jika Hex yang
dipilih, pengguna harus memasukkan 64 karakter. Untuk pengaturan yang lebih mudah, Passphrase (minimum 8 karakter)
yang direkomendasi.
Pre-Shared Key : Pre-Shared Key berfungsi sebagai password. Pengguna harus memasukkan 8 sampai 63 karakter string jika
Anda memilih passphrase. Pastikan password yang sama digunakan olh client untuk melakukan koneksi.
ACL
Current Access Control List Tabel ini menampilkan informasi MAC pada client.
Delete choosed Klik Delete Choosed untuk menghapus item.
WDS
Wireless Distribution System menggunakan media wireless untuk berkomunikasi dengan AP lainnya, seperti
Ethernet. Untuk melakukan ini, Anda harus mengatur ini AP yang ada di saluran yang sama dan menetapkan alamat
MAC dari AP lain yang Anda ingin berkomunikasi dengan dalam tabel dan kemudian mengaktifkan WDS.
Catatan !
Untuk menjalankan WDS harus menggunakan produk wireless yang sama (model yang sama lebih
baik);karena dua produk wireless yang berbeda mungkin mendukung pengaturan WDS yang berbeda. Dengan
demikian, meggunakan produk wireless yang sama akan mendukung fungsi yang sama.
Step 1. Pengguna ingin menggunakan fungsi WDS, silahkan ke halaman Wireless > Basic untuk memilih modus
WDS atau AP+ WDS (Repeater), dan buat AP dengan Network Name (SSID) dan Channel yang sama.
Setelah selesai, klik tombol Apply Changes.
2 PROLiNK_WNR1008
Step 2. Lalu pergi ke Wireless > WDS (1) untuk mengaktifkan fungsi WDS dan (2) masukkan alamat Wireless MAC
(silahkan pergi ke Status> Wireless Configuration untuk memastikan alamat BSSID) untuk setiap AP yang
merupakan bagian dari WDS. Klik tombol Apply.
MAC Address: Masukkan Wireless BSSID (MAC) 12 karakter dari wireless AP yang ingin Anda hubungkan. silahkan
pergi ke Status> Wireless Configuration untuk memastikan alamat BSSID)
Set Security Mengaktifkan fungsi WDS lalu Klik tombol Set Security untuk membuat WDS security.
Encryption: Pilih jenis encryption None, WEP 64 bits, WEP 128 bits, dan WPA2 (AES) dari menu pull-down.
WEP Key Format: Untuk jenis WEP 64 bits dan WEP 128 bits encryption, WEP Key Format adalah Hex atau ASCII.
WEP Key: Jika memilih Hex menggunakan angka hexadecimal (0-9, atau A-F). Pilih ASCII untuk menggunakan
karakter ASCII (case-sensitive).
Hexadecimal (WEP 64 bits): 10 Hex karakters (0~9, a~f).
Hexadecimal (WEP 128 bits): 26 Hex karakters (0~9, a~f).
ASCII (WEP 64 bits): 5 ASCII karakters (case-sensitive).
ASCII (WEP 128 bits): 13 ASCII karakters (case-sensitive).
Pre-Shared Key Format: Pre-shared Key Format akan aktif bila menggunakan WPA (TKIP) dan WPA2 (AES)
encryption ed. Ada 2 pilihan format untuk Pre-shared key, Passphrase dan Hex (64 karakters). Jika Hex di pilih ,
pengguna harus memasukkan 64 karakters string. Untuk kemudahan pengaturan, gunakan Passphrase (minimal 8
karakters) yang direkomendasi.
Pre-Shared Key: Pre-Shared Key berfungsi sebagai password. Pengguna harus memasukkan 8 sampai 63 karakter
string jika Anda memilih passphrase. Pastikan password yang sama digunakan olh client untuk melakukan koneksi.
Klik ini untuk melihat tabel WDS. Tabel ini menampilan alamat MAC, transmission packets dan errors, reception
packets dan Tx Rate (Mbps) counters untuk setiap WDS AP yang terkoneksi.
Show Statistics
WPS
Schedule
3.6.
DMZ Settings
MAC Filtering
IP Filtering
Virtual Server
VLAN
3.7.
Password
NAS
Media Share
NTP
Password/Key Masukkan passwords yang Anda register di website service provider. Max 30 alphanumeric karakters (case sensitive).
Apply Changes Setelah selesai melakukan pengaturan, Klik tombol Apply changes untuk menyimpan.
Reset Klik tombol Refresh untuk merefresh waktu.
Upgrade Firmware
Settings Management
Statistics
Halaman ini menampilkan counter paket untuk penerimaan dan transmisi sehubungan dengan jaringan Ethernet dan
nirkabel.
System Log
Reboot
Klik tombol Reboot untuk me restart Wireless Router.
BAGIAN 4: KONFIGURASI PC
4.1.
4.2.
Bagian ini menjelaskan bagaimana cara mengkonfigurasi Windows clients untuk Akses Internet melalui
Wireless Router.
Langkah pertama adalah memeriksa pengaturan TCP/IP pada PC.
Wireless Router menggunakan protokol TCP / IP jaringan untuk semua fungsi, sehingga sangat penting bahwa
protokol TCP / IP diinstal dan dikonfigurasi pada PC masing-masing.
Jika menggunakan pengaturan default Wireless Router, dan standar pengaturan TCP / IP pada Windows, tidak ada
perubahan perlu dibuat.
Secara default, Wireless Router akan bertindak sebagai DHCP Server, secara otomatis memberikan alamat IP
yang sesuai ke PC setiap PC boot.
semua versi non-server Windows, standar TCP / IP setting untuk bertindak sebagai DHCP client.
1. Pergi ke Start Control Panel Network dan Internet Network dan Sharing Center Manage Network
Connections Local Area Connection.
2. Klik kanan ikon Local Area Connection dan pilih Properties. Anda akan melihat gambar berikut:
3. Pilih Internet Protocol Version 4 (TCP/IPv4) atau 6 (TCP/IPv6)
untuk network card Anda.
1. Pergi ke Start Control Panel Network dan Sharing Center Manage Network Connections Local
Area Connection.
2. Klik kanan ikon Local Area Connection dan pilih Properties. Anda akan melihat gmbar berikut:
3. Pilih Internet Protocol Version 4 (TCP/IPv4) atau 6 (TCP/IPv6)
network card Anda.
Akses Internet
Untuk Windows XP
1. Pilih Start menu Control Panel Network dan Internet Connections.
2. Pilih Set up atau ubah Internet Connection Anda.
3. Pilih tab Connection, dan Klik tombol Setup.
4. Batalkan layar pop-up "Location Information".
5. Klik Next on the "New Connection Wizard" screen.
6. Pilih "Connect to the Internet" dan Klik Next.
7. Pilih "Set up my connection manually" dan Klik Next.
8. Centang "Connect using a Broadband connection that is always on" dan Klik Next.
9. Klik Finish untuk menutup. Saat ini New Connection Wizard Setup telah selesai.
Untuk Windows 7
1. Pilih Start menu Control Panel Network Sharing Center.
2. Pilih Set up a new connection atau network.
3. Pilih Connect to the Internet dan Klik Next untuk melanjutkan.
4. Pilih Broadband (PPPoE).
5. Masukkan User name dan Password yang disediakan oleh ISP, lalu Klik Connect untuk membuat koneksi.
Mengakses AOL
Untuk mengakses AOL (America On Line) melalui Wireless Router, AOL untuk Windows software harus di konfigurasi
menggunakan TCP/IP network access, daripada mengunakan koneksi dial-up. Proses konfigurasi berikut ini:
1. Jalankan AOL pada Windows communication software. Pastikan Versinya 2.5, 3.0 atau terbaru. prosedur ini
tidak bekerja untuk versi sebelumnya.
2. Klik tombol Setup.
3. Pilih buat lokasi, dan ubah nama lokasi dari "New Locality" menjadi " Wireless Router ".
4. Klik Edit Location. Pilih TCP/IP untuk kolom Network. (Biarkan nomor telepon kosong).
5. Klik Save, lalu OK.
6. Konfigurasi saat ini sudah selesai.
7. Sebelum meng klik "Sign On", selalu pastikan Anda menggunakan lokasi " Wireless Router ".
4.3.
Dari Macintosh Anda, Anda dapat mengakses Internet melalui Wireless Router. Prosedur nya berikut ini.
1. Buka TCP/IP Control Panel.
2. Pilih Ethernet dari Connect melalui menu pop-up.
3. Pilih menggunakan DHCP Server dari Configure menu pop-up. Kolom DHCP Client ID tidak boleh kosong.
4. Tutup TCP/IP panel, simpan hasil pengaturan Anda.
Jika menggunakan alamat IP statis selain DHCP, perubahan yang dibutuhkan sebagai berikut:
Set kolom Router Address ke r.alamat IP Wireless Router.
Pastikan pengaturan DNS Anda benar.
4.4.
Untuk mengakses Internet melalui Wireless Router, hanya perlu untuk mengatur Wireless Router sebagai "Gateway".
Pastikan anda login sebagai "root" sebelum mencoba perubahan.
Alamat IP Statis
Secara default, kebanyakan instalasi Unix menggunakan alamat IP statis. Jika Anda ingin terus menggunakan alamat IP
statis, buatlah perubahan konfiguasi berikut.
Set "Default Gateway" Anda ke alamat IP dari Wireless Router.
Pastikan pengaturan DNS Anda benar.
4.5.
4.6.
Bagian ini berlaku untuk semua stasiun nirkabel yang ingin menggunakan Wireless Router sebagai jalur akses,
terlepas dari sistem operasi yang digunakan pada klien.
Untuk menggunakan Wireless Router, setiap wireless station harus memiliki pengaturan yang kompatibel
sebagai berikut:
SSID (ESSID) (Extended Nama network harus sama dengan Wireless Router.
Service Set Identifier) Catatan! SSID (service set identifier) adalah case- sensitive.
Jika tidak ada security yang diaktifkan pada Wireless Router, security setiap stasiun harus dinonaktifkan
Disable
juga. Dan, Anda dapat menghubungkan Wireless Router tanpa security, tetapi TIDAK dianjurkan
Jika WEP aktif pada Wireless Router, setiap station harus menggunakan pengaturan yang sama
dengan Wireless Router.
WPA-PSK (TKIP/AES)/ WPA2-PSK (TKIP/AES): Jika satu dari security ini diaktifkan pada Wireless Router.
Personal (Pre-Shared Key) Setiap STA harus menggunakan algorithms dan passphrase yang sama dengan Wireless Router.
Pre-Shared Key Format: Memiliki pilihan untuk set Pre-shared key, Passphrase dan Hex (64
WPA karakters). Jika Hex yang dipilih, pengguna harus memasukkan 64 karakter. Untuk pengaturan yang
WPA2 lebih mudah, Passphrase (minimum 8 karakter) yang direkomendasi.
WPA2-Mixed Pre-Shared Key : Pre-Shared Key berfungsi sebagai password. Pengguna harus memasukkan 8 sampai
63 karakter string jika Anda memilih passphrase. Pastikan password yang sama digunakan olh client
untuk melakukan koneksi.
Enterprise (RADIUS)
RADIUS Server: RADIUS adalah otentikasi, authorization dan akuntansi client-server protokol. Client
WPA adalah Network Access Server yang keinginan untuk otentikasi link nya. The RADIUS adalah server yang
WPA2 memiliki akses ke database user dengan informasi otentikasi. Setiap stasiun harus mengatur Server
WPA2-Mixed RADIUS alamat IP, password dan port yang disediakan oleh ISP anda.
802.1x
Secara default, Wireless Router akan memungkinkan koneksi 802.11b, 802.11g dan 802.11n.
BAGIAN 5: PERMASALAHAN
5.1.
Pada BAGIAN ini mencakup beberapa masalah umum yang mungkin dihadapi ketika menggunakan Wireless Router
dan beberapa solusi yang mungkin untuk mereka. Jika Anda mengikuti langkah-langkah yang disarankan dan Wireless
Router masih tidak berfungsi dengan benar, hubungi dealer Anda untuk saran lebih lanjut.
5.2.
Solusi 1:
Periksa berikut ini:
Periksa apakah Wireless Router sudah terinstall dengan benar, LAN OK, dan powered HIDUP.
Pastikan PC dan Wireless Router Anda berada pada network segment yang sama.
Jika PC Anda di set ke "Obtain an IP address automatically" (DHCP client), silahkan lakukan restart.
Jika PC Anda menggunakan alamat IP statis, pastikan bahwa menggunakan alamat IP dalam rentang 192.168.123.1
sampai 192.168.123.253 sehingga sesuai dengan alamat default IP Wireless Router 192.168.123.254.
Juga, Network Mask harus di set ke 255.255.255.0 untuk menyesuaikan Wireless Router.
Pada Windows, Anda dapat memeriksa pengaturan ini dengan menggunakan Control Panel-Network untuk protokol
TCP / IP. Anda dapat memeriksa BAGIAN 4: KONFIGURASI PC-pengaturan TCP / IP untuk referensi.
5.3.
Masalah 1: Ketika saya memasukkan alamat IP atau URL, saya mendapatkan time out error.
Solusi 1:
Ada beberapa hal yang dapat menyebabkan hal ini. Coba ikuti beberapa langkah berikut.
Periksa apakah PC lain bekerja. Jika ya, pastikan bahwa pengaturan IP pada PC Anda sudah benar. Jika menggunakan
alamat IP statis, periksa Network Mask, Default DNS dan gateway.
Jika PC sudah dikonfigurasi dengan benar, tapi masih tidak berfungsi, periksa Wireless Router. Pastikan bahwa itu
terhubung dan HIDUP.
Jika Wireless Router sudah tekonfigurasi dengan benar, periksa koneksi Internet Anda (ADSL/Cable modem) untuk
melihat apakah bekerja dengan benar.
Masalah 2: Beberapa aplikasi tidak dapat berjalan dengan semestinya ketika menggunakan Wireless Router.
Solusi 2:
Proses data yang dilalui melalui Wireless Router tidak transparant.
Gunakan fitur Filter Settings untuk memungkinkan menggunakan aplikasi Internet, yang tidak berfungsi semestinya.
Jika tidak juga menyelesaikan masalah, Anda dapat menggunakan fungsi DMZ. Ini bisa bekerja untuk hampir semua aplikasi,
namun:
5.4.
Solusi 1:
Periksa berikut ini:
Mode: PC Anda di set ke mode Infrastructure. (Access Points selalu bekerja dengan mode Infrastructure)
SSID: SSID (service set identifier) pada PC Anda dan Wireless Router tidak sama.
Ingat bahwa SSID itu case-sensitive. Jadi, contoh "Workgroup" tidak sama dengan "workgroup."
Security: kedua PC dan the Wireless Router Anda harus menggunakan pengaturan yang sama untuk security.
o Disabled: Pengaturan standar untuk security Wireless Router dinonaktifkan, sehingga stasiun nirkabel
Anda juga harus dinonaktifkan security nya.
o Enabled: Jika security aktif pada Wireless Router, PC Anda harus mengaktifkan security nya juga dan key
harus sama.
o Sangat diarankan untuk membuat keamanan yang bisa mencegah unauthorized mengakses ke jaringan
nirkabel Anda. Setting keamanan WPA2 dianjurkan yang menawarkan keamanan yang lebih kuat daripada
WEP. Kedua komputer Anda dan Wireless Router harus memiliki pengaturan yang sama untuk keamanan.
Channel: Jaringan area lokal nirkabel diaktifkan dan dikonfigurasi secara default. Jika perlu, silakan cek saluran dan
cocok untuk terminal, misalnya, notebook anda. Kedua komputer Anda (klien) dan Wireless Router harus mengatur
ke saluran yang sama untuk koneksi.
Solusi 2:
Sistem nirkabel akan terhubung pada kecepatan tertinggi, tergantung pada jarak dan lingkungan. Untuk mendapatkan
kecepatan koneksi tertinggi mungkin, Anda dapat melakukan percobaan dengan:
Wireless Router location: Coba ubah lokasi dari Wireless Router. Untuk melihat apakah interferensi radio yang
menyebabkan masalah, melihat apakah koneksi mungkin dilakukan ketika dekat dengan Wireless Router.
Wireless Channels: Jika interferensi ayng menjadi masalah, ubah channel yang lain dan mungkin menunjukan
peningkatan yang baik.
Radio Interference: Perangkat lain mungkin menyebabkan interferensi. Anda dapat mencoba untuk mematikan
perangkat wireless yang lain, dan lihat apakah ini membantu. Setiap perangkat yang "noisy" harus dilindungi atau
direlokasi.
RF Shielding: Lingkungan Anda mungkin cenderung memblokir pengiriman data antara stasiun nirkabel. Ini berarti
kecepatan akses tinggi hanya mungkin bila dekat dengan Wireless Router.
6.1.
Sekelompok stasiun nirkabel dan jalur akses tunggal, semua menggunakan SSID yang sama (service set identifier),
membentuk Basic Service Set (BSS).
Menggunakan SSID (service set identifier) yang sama sangat penting. Perangkat dengan SSID yang berbeda tidak
dapat berkomunikasi dengan yang lainya.
6.2.
6.3.
WEP
.
WEP (Wired Equivalent Privacy) adalah standard untuk mengenkripsi data sebelum dikirim. Hal ini diinginkan karena
tidak mungkin untuk mencegah snoopers menerima data yang ditransmisikan oleh stasiun nirkabel Anda. Tetapi jika
data dienkripsi, maka berarti kecuali penerima yang dapat mendekripsikannya.
Jika WEP digunakan, stasiun nirkabel dan titik akses harus memiliki pengaturan keamanan yang sama untuk
masing-masing sebagai berikut:
WPA / WPA2 (Wi-Fi Protected Access) adalah lebih aman daripada WEP.Menggunakan "Shared Key" yang
memungkinkan kunci enkripsi untuk dibuat ulang pada interval tertentu. Ada beberapa pilihan enkripsi: TKIP, AES,
TKIP-AES dan setup tambahan untuk RADIUS diperlukan dalam metode ini. Yang paling penting di luar fitur WPA
menjadi standard melalui 802.11i/WPA2 adalah: pre-authentication, yang memungkinkan roaming cepat aman tanpa
latensi sinyal terlihat.
Jika WPA / WPA2 digunakan, stasiun titik akses nirkabel dan harus memiliki pengaturan keamanan yang sama.
802.1x
Dengan 802.1x authentication, PC nirkabel dapat bergabung dalam jaringan dan menerima pesan yang tidak
dienkripsi, bagaimanapun, setup tambahan untuk RADIUS untuk mengeluarkan kunci WEP secara dinamis akan
diperlukan.
RADIUS adalah authentication, authatauization, dan accounting client-server protocol. Klien adalah akses jaringan
server yang keinginan untuk otentikasi link nya. Server memiliki akses ke database user dengan informasi otentikasi.
6.4.
Untuk memungkinkan stasiun nirkabel (STA) untuk mengakses Access Point (AP), nirkabel stasiun dan access point
yang harus menggunakan pengaturan yang sama, sebagai berikut:
Jika tidak ada security yang diaktifkan pada Wireless Router, security setiap stasiun harus dinonaktifkan juga. Dan,
Disable
Anda dapat menghubungkan Wireless Router tanpa security, tetapi TIDAK dianjurkan
WPA-PSK (TKIP/AES)/ WPA2-PSK (TKIP/AES): Jika satu dari security ini diaktifkan pada Wireless Router. Setiap STA
harus menggunakan algorithms dan passphrase yang sama dengan Wireless Router.
Personal (Pre-Shared Key)
Pre-Shared Key Format: Memiliki pilihan untuk set Pre-shared key, Passphrase dan Hex (64 karakters). Jika
WPA Hex yang dipilih, pengguna harus memasukkan 64 karakter. Untuk pengaturan yang lebih mudah, Passphrase
WPA2 (minimum 8 karakter) yang direkomendasi.
WPA2-Mixed
Pre-Shared Key : Pre-Shared Key berfungsi sebagai password. Pengguna harus memasukkan 8 sampai 63
karakter string jika Anda memilih passphrase. Pastikan password yang sama digunakan olh client untuk
melakukan koneksi.
Enterprise (RADIUS)
RADIUS Server: RADIUS adalah otentikasi, authorization dan akuntansi client-server protokol. Client adalah
WPA Network Access Server yang keinginan untuk otentikasi link nya. The RADIUS adalah server yang memiliki akses
WPA2 ke database user dengan informasi otentikasi. Setiap stasiun harus mengatur Server RADIUS alamat IP, password
WPA2-Mixed dan port yang disediakan oleh ISP anda.
802.1x
7.1.
7.2.
7.3.
SINGAPORE
FIDA INTERNATIHIDUPAL (S) PTE LTD
Block 16 Kallang Place, #06-02 Kallang Basin Industrial Estate, Singapataue 339156.
Tel : (65) 6357 0668
Email : support@fida.com
MALAYSIA
FIDA SYSTEMS (M) SDN BHD
29 Jalan USJ 1/31, 47600 Subang Jaya, Selangatau Darul Ehsan, Malaysia.
Tel : (60) 3 8024 9151
Email : support_my@fida.com
INDONESIA
PROLiNK INDONESIA
Jl. Cideng Barat No. 79, Jakarta Pusat 10150 - Indonesia.
Tel : (62) 21 3483 1777
Email : support@prolink.co.id
PROLiNK is a trademark of FIDA International (S) PTE LTD dan is manufactured under its authatauity. All other brdans, products, services, logos dan
company names mentioned herein are trademarks of their respective owners. All specifications, designs dan contents are subject to changes without
priatau notice. © Copyright 2010. PROLiNK all rights reserved.