Katalog STP Fe Petro
Katalog STP Fe Petro
Katalog STP Fe Petro
FE PETRO FEATURE FASTER FUELING TIMES FE PETRO FEATURE VARIABLE LENGTH OPTION
FE PETRO FEATURE SUPERIOR BEARING COOLING FE PETRO FEATURE A RELIABLE CHECK VALVE
Our STP’s use the The STP uses
FE Petro cooling FE Petro’s proven line
system. This unique check valve. At 2 3/4"
system continually (70mm) in diameter,
passes over 1 GPM this valve reduces
through a fine bronze pressure loss at high
filter and directly flow rates, resulting in
through motor faster fueling times
bearings whenever and lower power
pump is operating. consumption.
BENEFIT TO YOU
The FE Petro check valve is proven to seal. You can avoid
BENEFIT TO YOU purchasing additional check valves when the STP is used
This system has been designed to extend critical bearing with some popular electronic line leak detectors because of
and motor life. this proven reliability.
FE PETRO FEATURE MANUAL PRESSURE RELIEF
TWO HP FIXED SPEED MODELS
A standard FE Petro feature.
When necessary during FE PETRO FEATURE HIGHEST FLOW
maintenance to bleed line The STPM200 with MagShellTM provides flow rates previously
pressure to zero, a vent screw is unavailable in 4" fixed speed submersible pumps.
provided. By turning this screw,
product is diverted
back to the tank,
dropping line
pressure to zero.
BENEFIT TO YOU
Reduces fuel discharged into the sump manhole or dispenser BENEFIT TO YOU
pan during servicing, further protecting service technicians One pump can provide good flow rates for up to 8-10 retail
and the environment. nozzles flowing simultaneously.
BENEFIT TO YOU
The highest performing 2 HP fixed
speed submersibles ever offered. Higher
BENEFIT TO YOU flow means faster fill rates during peak
This feature reduces the risk of correcting one problem and business periods, increasing daily
causing another. throughput and your profit potential.
120
TOTAL HEAD IN FEET
100
80
60
40
20
BENEFIT TO YOU 0 20 40 60 80
This feature allows for fewer fittings to connect the pump to the BENEFIT TO YOU
discharge line, and requires less space in the sump. Increase flow rates 1 to 2 GPM per nozzle with 5-8 nozzles
operating. Get the newest technology available and go easy
on your budget at the same time. FE Petro pump motors
sell for about 1/3 the cost of a complete pump change-out.
ACCESSORIES STP SPECIFICATIONS
The FE Petro optional single phase motor control box is
available in two configurations. These control boxes are UL POWER SUPPLY OPTIONS:
listed, CSA Certified or C-UL listed and fit any horsepower • 60 Hz Applications: Available in 1/3, 3/4, 1 1/2, 2 HP and
fixed speed 4" submersible. Models are available in both 1 1/2 and 2 HP high pressure models in 208-230 volt,
120 volt and 220 volt coils for 50 and 60 Hz power supplies. single phase.
• 50 Hz Applications: Available in 3/4, 1 1/2 and 1 1/2 HP
STP-SC1: The Smart Controller™ using power monitoring
technology offers all the features of our standard STP-CBS high pressure models in 220-240 volt, single phase,
control box, plus the following protection and diagnostics: and 380-415 volt 3 phase.
• Dry Running Protection with Auto Reset PUMP MOTOR:
• Low Voltage Detection • Centrifugal type, directly interchangeable with most
• Pump Motor Failure Detection competitive makes.
• Open Circuit Detection • Maximum liquid viscosity: 70 SSU at 60° F. (15.5° C).
• Extended Pump Run Detection • Thermally protected: Automatic thermal overload
• Slave Pump(s) Auto Start Operation turns motor off at approximately 205° F (95° C) and
resets on at approximately 115° F (45° C).
• Alternating Pump Control
LIQUID COMPATIBILITY:
• Remote Diagnostic Polling Capability
• Standard units compatible with fuel mixtures
• Push button last 5 fault recall for quick
containing up to 15% ethanol or methanol with
service diagnostics
gasoline and 20% MTBE, 20% ETBE, or 17% TAME
• System abnormalities are identified by an indicator light
with gasoline, and diesel fuels.
and audible alarm.
• Alcohol/Gasoline models (designated with AG in model
STP-CBS: Control Box with number) are compatible in fuel mixtures containing
wiring terminals, contactor any combination of ethanol or methanol and
relay and pilot light with lock gasoline and 20% MTBE, 20% ETBE, or 17% TAME
out toggle switch. with gasoline, and diesel fuels.
One required per pump. CHECK VALVE:
Enclosure size is 8 1/2" x 5" x 3" • 2 3/4" (70mm) diameter constructed of aluminum and
(215mm x 127mm x 76mm). steel with fluorocarbon seal. Alcohol gas compatible.
PRESSURE RELIEF VALVE:
IFS: Our intake filter
screen option utilizes • Standard valve is set to relieve static line pressure at 35-
316 stainless 50 PSI (2.38 to 3.4 bar), reseals above 30 PSI
steel to filter particles (2.0 bar). Other settings available.
.009" (.23mm/230 AIR ELIMINATOR:
microns) and larger. It • Returns air to tank with one way check valve to prevent
can significantly reduce dispenser filter changes. back flow.
SEAL ELASTOMERS:
• All wetted seals on standard units are fluorocarbon.
• Alcohol/Gasoline (AG) models use high grade
FE PETRO FEATURE SERIAL COMMUNICATION fluorocarbon seals.
SYPHON:
The STP-SCI Smart • Syphon Primer is venturi type, capable of 26" Hg
Controller incorporates (66cm) vacuum.
a RS 485 serial • Syphon Check Valve is machined brass.
communications system MagShellTM
for communication and • 304 stainless steel construction. Shell is expanded .084"
intelligence sharing with
results in increased flow area through motor 45%.
INCON fuel
management systems. • Magshell is standard on 2 HP models . Not available on
1
⁄3 through 1 1⁄2 HP.
APPROVALS AND/OR LISTINGS:
• UL, cUL, ATEX, BASEEFA, TUV, SAA, BKI, INMETRO,
TIIS, KHK, FTZU, ROSTEST, others pending
BENEFIT TO YOU (Approvals vary by model. Consult factory for
Pump diagnostics is reported within moments to remote approvals by model number).
monitoring parties, reducing service call time. Serial link QUALITY CERTIFICATION:
allows ATG to control pump preventing water from being • FE Petro is an ISO 9001 Certified Manufacturer.
pumped, elimination of syphon piping, and other functions
designed to reduce station operating costs.
FE PETRO
60 HZ 1/3 through 1-1/2 HP Pump Performance Chart
FLOW IN LITERS PER MINUTE
76 151 227 303 379 454 530 606 681
150
1 2
140 3 KEY TO PUMP 43
CURVES:
4
70
60 18
50
40 12
30
C2
20 6
10
A1 B1 D1 A2 C1 B2 D2
140 1 43
2
3
CURVES - CURVES:
120 7 NUMBER OF 37
NOZZLES —— STPHM200
8 OPERATING ------ (2) STPHM200
110 AT THE —— STPM200
9 SAME TIME ------ (2) STPM200
10
100 31
90
80 24
70
60 18
50
40 12
30
20 6
10
STPHM200 STPM200 (2) (2)
STPHM200 STPM200
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240
2
3 SYSTEM
CURVES -
35 4 NUMBER OF
NOZZLES
5 OPERATING
6 AT THE
30 7 SAME TIME
8
9
25
10
20
15
10
5
STP75 STPH150 STP150 (2) STP75 (2) STPH150 (2) STP150
3/4 HP 1.5 HP
0 50 100 150 200 250 300 350 400 450 500 550 600 650
Note: The VL2 length can 1/3 HP USE IF MODEL LENGTH IS 86 – 147” (218 CM to 373 CM)
be used in 94% of all Use VL1 if model length is shorter than 84 down to 55” (213 CM to 139 CM)
known installations. Use VL3 if model length is longer than 118 up to 202” (299 CM to 513 CM)
This table shows 3/4 HP USE IF MODEL LENGTH IS 89 – 149” (226 CM to 378 CM)
Use VL1 if model length is shorter than 86 down to 57” (218 CM to 114 CM)
installations where Use VL3 if model length is longer than 120 up to 205” (305 CM to 520 CM)
a VL1 or VL3 is 1 1/2 HP USE IF MODEL LENGTH IS 91 – 152” (231 CM to 386 CM)
required: Use VL1 if model length is shorter than 89 down to 60” (226 CM to 152 CM)
Use VL3 if model length is longer than 123 up to 208” (312 CM to 528 CM)
1 1/2 HP USE IF MODEL LENGTH IS 91 – 153” (231 CM to 388 CM)
High Use VL1 if model length is shorter than 90 down to 60” (228 CM to 152 CM)
Pressure Use VL3 if model length is longer than 123 up to 208” (312 CM to 528 CM)
2 HP USE IF MODEL LENGTH IS 94 – 155” (238 CM to 393 CM)
Fixed Use VL1 if model length is shorter than 92 down to 63” (233 CM to 160 CM)
Speed Use VL3 if model length is longer than 126 up to 211” (320 CM to 536 CM)
Phone: +1 (608) 838-8786 USA & Canada: 1-800-225-9787 Mexico: 001-800-738-7610 Fax: +1 (608) 838-6433
■ ■ ■
Rev. 8/03