Ariston Ab108xit 2
Ariston Ab108xit 2
Ariston Ab108xit 2
AB108XIT
Commercial code:
22443
page 1
General notes
1. Models of same range share the same exploded views, which report the richest set of spare parts:generally, a model does not necessarly have a
related spare part for each particular shown on exploded views.
2. Some spare parts can not be represented directly on the exploded views (instruction booklets, specific kit, etc...). You can find those codes in the
spare parts list with the same reference of particular where spares are installed or with references 099, 999. Instruction booklets, once managed,
appear with 000 reference.
3. On the higher right site of each exploded view there is a serial number which indicates the beginning of the production of certain range:some
models might have more than an exploded view for a given category, each distinguished by a different serial no.and linked to another spare parts
list, In this case, serial no. is required to supply the right spare part code. Exploded view to be considered is the one with a more recent serial no.
but previous than the one of the model that needs assistance.
4.Exploded views might require further updates even after publishing. Addition of new spares will go on following the already existing numeration
references. Revision number of an exploded view is shown into last four digits of serial number into upper right hand corner.
5.The spare parts list associated to an exploded view shows related codes of spares managed for a certain model; for each spare part other
informations are available:
REF: reference no of spare into a table; SUBSTITUTE: list of spare(s) which can replace a code but that keeps same functional characteristics
INDUSTRIAL CODE: list of variables of a model (shown into model label) where such spare is used; NOTICE: code of information(s) to refer to
complete technical intervention, track for changes or to find correct spare part code.
6. Some notices, into a same section are generic therefore cannot be directly linked to a spare part. In order to assist a model in the best way as
possible, it is helpful to pay attention to all notices and constantly verify documentation updates
7.Technical documentation cover shows model name and its commercial codes
page 2
pdf_tavola_title_ENG
cod. 1140110
page 3
Spare parts list
page 4
022 C00065871 blanking plug
page 5
pdf_tavola_title_ENG
cod. 1140210
page 6
Spare parts list
page 7
019 C00093848 80224430130 cradle outer- set n1040286
page 8
pdf_tavola_title_ENG
cod. 1140310
page 9
Spare parts list
page 10
017 C00064529 80224430000,80224430100, dispenser body n1040276
80224430101
page 11
042 C00064533 hopper cover 1 ev
page 12
Notices
n1040061
Trouble-shooting.
-------------------------------------------------------------------------------------------------------------------------------
Intervention procedure on 2000 washing machines
2. the action, for the first 4', of the electrovalve and the drain pump
the number of flashes indicates the fault code; the code should be read as follows:
· each fast flash (2/3 flashes of the led very close together) represents one code value
· the fault code is evaluated by counting the number of flashes occurring at 3/4" intervals from one another
· stop counting when the washing machine waits the equivalent of approximately 8/9" between flashes
E.g.: F03
(FIGURE NT 00)
2. Autotest
page 13
Should the washing machine not be signalling an error, you can check it using a serial key and using a particular autotest cycle, which is to be
activated as follows:
1. bring the washing machine to reset position (coloured ball) for at least 5" and wait until the led flashes on reset mode
4. wait for the door to lock and for the selector to start turning
· selector moves on up to position 0 (12h if the appliance has a delay, programme 1 if it has no delay)
· loads the wash electrovalve and pre-wash electrovalve at the same time until the pressure switch is on full
· STOP
The test cycle can be repeated as many times as you wish following the same procedures
The test cycle can be interrupted by positioning the selector knob on one of the reset positions.
Overhaul CNE
Replace Card
page 14
F02: Blocked Motor, Short-circuited/Open Tachometry
Overhaul CNE
Replace Card
Overhaul CNA
Replace NTC
Replace Card
F04: Overflow and Pressure Switch Empty found at the same time (Pressure Switch stuck on Empty)
Overhaul CN1
Replace Card
Change Pump
Replace Card
page 15
F06: Selector Error (a part no. cannot be found)
Replace Selector
Replace Card
Overhaul CN1
Overhaul CN1
Replace Card
Replace Card
Overhaul CN1
Replace Resistance
Replace Card
F10: Pressure Switch Empty and Full or neither Empty nor Full Pressure Switch Found
Overhaul CN1
page 16
Control CN1/Pressure Switch Continuity
Replace Card
Overhaul CN1
Overhaul CNF
Replace Pump
Replace Card
4. Replace NTC
2. Overhaul CN1
page 17
3. Overhaul connector connection
3. Control Continuity of cabling CNC / basket block and basket block supply
5. Replace card
These are shown in a display located on the instrument panel of LVB2000 ma-chines
Evolution Indesit.
Are those that are indicated according to the version via LED stand by/on or
page 18
· retrieve the EEPROM from the old card
· reassemble the EEPROM onto the new replacement card (without EEPROM)
· the above-mentioned checks have been carried out and no problems have been detected on the wiring or to the motor
· the card fitted onto the washing machine is a 12 or 20 version (the version is indicated by a label on the module-containing box with SW20 or
SW12)
you should:
· fit on an updated EEPROM to request from the assistance service centre, stating the code (e.g. 80xxxxx0000 or 46xxxxx0000), the serial number
and the washing machine model.
n1040064
New SW version introduced on the hybrid module.
-------------------------------------------------------------------------------------------------------------------------------
On AL109XIT (22360), AL89XIT (22362), AL68XIT (22363), AB108XIT (22443) and AB88XIT (22444) Washing machines, some EEPROMs are
used with the modified software.
page 19
Mod. AL108XIT Serial no. 00218.0001
The modification of the EEPROM has led to the use of new instruction manuals which keep the same SAT part nos. as the pre-modification ones,
whose stocks have been eliminated.
n1040066
LB2000 Hardware (Serial Spanner and Pliers)
-------------------------------------------------------------------------------------------------------------------------------
As of 05.04.2000, the following Spare Parts are available from the Warehouse:
Part no.066055 - Serial spanner for LVB2000 autotest. It has not to be linked to PC. (substituted with 077454);
Part no. 077454 - Serial spanner for LVB2000-PC White (substituted with 084566);
Part no. 084566 - Serial spanner forLB2000/EVOI -PC BIANCA (substituted with 095669 LB2000/EVOI, EVOII - PC).
n1040078
WARNING: Remove the eeprom
-------------------------------------------------------------------------------------------------------------------------------
Remove the eeprom with pliers part no. 066292 from the faulty module and insert it on the new module / display module, otherwise the machine
will not function.
L'EPROM contains the software that characterizes the model, therefore each apparatus should have his own specific eprom(see the list spare
parts).
page 20
n1040087
Interchangeability of electrovalves.
-------------------------------------------------------------------------------------------------------------------------------
Electrovalve part no. 064535 is interchangeable with part no. 066518.
Part no. 064535 will continue to be handled until stock run out.
n1040088
LB2000 Washing machine parasprays at Comunanza and Teverola
-------------------------------------------------------------------------------------------------------------------------------
Having received requests for parasprays used on the LB2000 Washing machine ranges, these have been coded.
These parts will be handled upon request only and warehouse stocks are therefore not foreseen.
n1040191
Integrated probe on washing resistance.
-------------------------------------------------------------------------------------------------------------------------------
From the registration no. 10312.0001 on Washing machines produced in the Comunanza Factory Plant, in relation to the present Notice, the
probe's housing hole has been eliminated from the tub cover (application of the thermostat tap hole code 020181), the same has been performed
directly on the resistance.
Code 081653 - Integrated probe on resistance (for ohmmici values, see enclosed figure);
Code 081837 - Resistance 1700W / 230 V with thermo fusible + adjustable thermostat bulb hole L= 169,5 mm;
Code 081654 - Resistance 1700W / 230 V with thermo fusible + adjustable thermostat bulb hole L = 212,5 mm.
page 21
The pre-modification items are not individually interchangeable with the modified ones and as much will continue to be normally handled.
For management requirements, tub with cavity probe/thermostat (until stock depletion) are used and according to necessities, the top cavity
thermostat as above, can be used.
In case of tub modificaton(without cavity) on equipment pre-modificated: the new resistance with probe cavity, the new probe should be used and
sometimes also the long probe thermostat.
The introduction date of modification especifically for each model, it is visible on the plate of EPROM's description SAT code, which is inserted on
the model's documentation Xpartfinder
n1040192
Module LB2000 without Eeprom.
-------------------------------------------------------------------------------------------------------------------------------
From registration no. 10502.0001, on all the LB2000 Washing machine models, with exception to the Evolution range, the module without Eeprom
code 080981 has been used.
The new module, may be used in place of the above mentioned, that will be handled until stock depletion and that however may be used on pre-
modified models.
n1040208
New hardware testing plug LB2000 Teverola.
page 22
-------------------------------------------------------------------------------------------------------------------------------
From the registration number 10827.0001 on all washing machines LB2000 with program selector, produced in the factory in Teverola, a new
hardware testing plug cod. 084817 is used.
The new plug is not interchangeable with the pre-modified one cod. 064899; so both have to be managed. In case of substitution of the piece of
furniture on am equipment, preceding the registration number 10827.0001, it will be necessary to put on the suitable plug.
This modification of the registration number 10820.0001 is extended to all washing machines and wash-driers with a programs' selector produced
in the factory in Comunanza.
n1040211
Serial cable to connect the hardware key with the PC.
-------------------------------------------------------------------------------------------------------------------------------
To connect the hardware key: LB2000 with the personal computer,you must use
a serial cable, pin to pin 9 pin F/F, to garantee the availability, it was
n1040212
New switch
-------------------------------------------------------------------------------------------------------------------------------
From the registration no. 10507.0001, on all Washing machines produced in the Teverola production and from 10402.0001 on Comunanzaplant a
new switch NA code SAT 075445 has been used in place of the switch NA code SAT 063971.
The new switch differs to the pre-modification switch, which will continue to be normally handled for the Faston type of connections (see enclosed
illustration NT006300).
n1040229
Items with IDC connectors.
-------------------------------------------------------------------------------------------------------------------------------
From November 2001, in order to improve electrical connections on models produced in Teverola and Comunanza plants, electrical components
supplied with IDC connectors have been applied.
page 23
New particulars are:
page 24
Code 087188 = HEATING ELEM.TERMAL CUT-OUT 1700W/230V L= 169,5 mm ;
Code 086661 = HEATING ELEMENT FOR PROBE 1700W 230V L= 212.5 mm;
Code 084838 = MODULE (LESS EEPROM) MODULE UNIV. STRIP SW 220 IDC.
Wires with IDC connectors can be found directly on spare parts list of models to be repared.
This change has not affected EEPROM which remain the same.
1 – Find the modified particular into spare parts list of model of interest
2 – Check list of models herebelow given and compare with their serial no.
page 25
AB108XEO (26389) Matr.11209.0001;
page 26
AL109XEU (22514) Matr. 11203.0001;
page 27
AL89XSEX (24735) Matr. 11203.0001;
ALD12UK(26093) Matr.20527.0001;
page 28
W106XDE (24836) Matr. 20114.0001;
page 29
W683XGIT 24812) Matr. 20114.0001;
page 30
WD84TEX (24907) Matr. 20603.001;
page 31
Models of Teverola factory.
page 32
W83SP (23317) Matr. 20312.0001;
n1040230
Modified shock absorber bracket - Comunanza plant
-------------------------------------------------------------------------------------------------------------------------------
From the registration no. 11107.0001, the washing machines and Washer-Dryers produced in the Comunanza factory Plant, have used modified
shock absorbers with the bracket that fixes onto the cabinet.
The modification also involved the cabinets in the fixing area that for the shock absorbers represent a different type of slotting (see enclosed figure).
To avoid the proliferation of the codes, the modified cabinets are handled with the same SAT code as the pre-modification, when replacing the
cabinet you will need to check the registration number of the appliance.
In order to perform a proper task the intervention of the cabinet replacement it is recommended, that at least in the initial phase, to keep both the
page 33
combination of shock absorbers in stock. The shock absorbers code 066184 and 064503 will continue to be normally handled.
n1040242
Power card with welded eeprom.
-------------------------------------------------------------------------------------------------------------------------------
From serial number 20304.0001, IDC power card with welded eeprom is used to ensure the perfect connection of all parts, in the Comunanza,
Teverola and Brembate factories.
To replace the module with welded eeprom, it will be necessary to use the eeprom indicated in the SAT document of the model concerned.
To replace the module on a unit with welded eeprom (Cod. 084838, 089405, 089404, 089416, 089074, and 090505), both the SAT module and the
eeprom are required, because the latter cannot be reused.
n1040282
New drainage OKO system.
-------------------------------------------------------------------------------------------------------------------------------
From serial number 21219.0001, the new "OKO" drainage system has been introduced on the washing machines produced in the Comunanza
factory.
The last two numbers of the Industrial Code (located on the rating plate) of the models relevant to this note will be 30 (e.g. 80233560130 - see
Appendix A)
N.B. The industrial code will not change on the models with induction motor (see following list).
page 34
ABS53XIT 80224800000
AB54XPT 80224870100
AB63XEX 80225100100
ABS63XEU 80225180100
WS44XIT 80233440100
WS431TXEX 80233470100
WS642TXEX 80233540100
W63XSP 80233890000
AB53XEU 80238820000
AB65XEU 80238830000
AL 64XSP 80239020100
WS43XIT 80244510000
WS53XIT 80244520000
WH66TXE 80253750100
ABS63XEO 80263900000
- EEPROM (the OKO system requires a new setting of load timing parameters). THE NEW EEPROMS REPLACE ALL THE ONES CODED
PREVIOUSLY.
- OKO PUMP BOWL BLOWER + BALL (see fig. 2A, 2B and 2C);
- HOPPER (shifted in front of detergent loading tube connection). Fig. 3A post-modification. Fig. 3B premodification);
page 35
In particular, the OKO system consists of a spherical plastic component inserted in the tube that connects the bowl to the drain pump (see fig.2 A).
At the beginning of each wash cycle the washing machine fills water for 10 seconds and activates the drain pump for 2 seconds. In this way, the
water level in the bowl is different from that in the drain tube; this difference increases the thrust of the ball upwards, closing the bowl-pump
connection tube hermetically (see fig. 2D).
1) separating the wash water and the water in the drain hose, thus saving energy during the heating phase;
With the introduction of this new component, the detergent collecting tube is no longer required and the pump has one hole only to convey water
from the tank.
For the correct operation of the OKO system, it is important that the drain hose of the washing machine remains fixed to the back of the unit with a
plastic clamp (to this end, the clamp withstands a 25 kg load; see reference 1 in fig. 4); otherwise, the drain hose must absolutely reach the height
of the clamp. (minimum 60 cm.)
n1040286
Shock absorbers with 8.15 mm fixing hole.
-------------------------------------------------------------------------------------------------------------------------------
From serial number 30127.0001, for appliances produced in the Comunanza factory, the shock absorbers will be fixed to the tank unit cradle using:
the 8 mm diameter screw code 093750 in place of the 10 mm screw code 030446, and related locking nut code 030443 in place of code 030680.
The premodified shock absorbers code 086515 and 086372 will continue to be used, whereas cradles code 064518 and 066074 will be used until
stocks run out, after which they will be replaced with the new items after widening the shock absorber fixing holes to a diameter of 11 mm.
page 36
n1040291
Interchangeability of bowls on LB2000 appliances Comunanza..
-------------------------------------------------------------------------------------------------------------------------------
The Comunanza factory has modified the oscillating unit on all the 2000 range models produced in the Comunanza factory:
a) From serial number 21219.0001, the LB 2000 EVO bowl (see fig. 02) is gradually replacing the LB2000 version (see fig. 01), with the following
differences:
· Detergent loading tube (washing machine SAT code 092161and combined washer-dryer SAT code 092273);
· OKO pump bowl tube (models code 092174, Snella models with induction motor code 094312);
· Hopper (for rotary slide drawer SAT code 092176, for linear slide drawer code 092314);
b) From serial number 30312.0001, all washing machines produced in the Comunanza factory have been equipped with the new LB2000 EVO II
range bowl (see fig. 03), in place of the LB2000 EVO version (see fig. 02), with the following difference:
· Porthole seal rear fixing ring for 30 cm diameter SAT code 092155;
Two LB2000 Evo bowl codings have been created in order to reduce the number of bowls managed by the After-sales Service (see fig. 04):
page 37
1) LB2000 Evo bowl kit coding (Table 01);
All bowl codes (with related interchangeability), are indicated in fig. 04 TAB. 03 attached to this Note.
Starting from serial number 30325.0001, for all the versions of Evizzate SNELLA LB2000 washing machines produced in the Comunanza factory
the diameter of tapered porthole must seal return 28 cm. Starting from this serial number all the washing machines must be supported with door
seal and fixing ring in old version.
Starting from serial number 30616.0001, for all the washing machines Evizzate LB2000 produced in Comunanza, the diameter of tapered porthole
must seal return 28 cm. Starting from this serial number all the washing machines must be supported with door seal and fixing ring in old version.
n1040061
Trouble-shooting.
-------------------------------------------------------------------------------------------------------------------------------
Intervention procedure on 2000 washing machines
page 38
1. the continuous rotation of the selector knob
2. the action, for the first 4', of the electrovalve and the drain pump
the number of flashes indicates the fault code; the code should be read as follows:
· each fast flash (2/3 flashes of the led very close together) represents one code value
· the fault code is evaluated by counting the number of flashes occurring at 3/4" intervals from one another
· stop counting when the washing machine waits the equivalent of approximately 8/9" between flashes
E.g.: F03
(FIGURE NT 00)
2. Autotest
Should the washing machine not be signalling an error, you can check it using a serial key and using a particular autotest cycle, which is to be
activated as follows:
1. bring the washing machine to reset position (coloured ball) for at least 5" and wait until the led flashes on reset mode
4. wait for the door to lock and for the selector to start turning
· selector moves on up to position 0 (12h if the appliance has a delay, programme 1 if it has no delay)
· loads the wash electrovalve and pre-wash electrovalve at the same time until the pressure switch is on full
page 39
· drains and spins
· STOP
The test cycle can be repeated as many times as you wish following the same procedures
The test cycle can be interrupted by positioning the selector knob on one of the reset positions.
Overhaul CNE
Replace Card
Overhaul CNE
Replace Card
Overhaul CNA
Replace NTC
Replace Card
page 40
F04: Overflow and Pressure Switch Empty found at the same time (Pressure Switch stuck on Empty)
Overhaul CN1
Replace Card
Change Pump
Replace Card
Replace Selector
Replace Card
Overhaul CN1
Overhaul CN1
Replace Card
Replace Card
page 41
F08: Resistance Missing or Pressure Switch stuck on Full Found
Overhaul CN1
Replace Resistance
Replace Card
F10: Pressure Switch Empty and Full or neither Empty nor Full Pressure Switch Found
Overhaul CN1
Replace Card
Overhaul CN1
Overhaul CNF
Replace Pump
Replace Card
page 42
1. Check the effectiveness of contacts on CNC Connector Card
4. Replace NTC
2. Overhaul CN1
3. Control Continuity of cabling CNC / basket block and basket block supply
page 43
4. Replace basket block
5. Replace card
These are shown in a display located on the instrument panel of LVB2000 ma-chines
Evolution Indesit.
Are those that are indicated according to the version via LED stand by/on or
· reassemble the EEPROM onto the new replacement card (without EEPROM)
· the above-mentioned checks have been carried out and no problems have been detected on the wiring or to the motor
· the card fitted onto the washing machine is a 12 or 20 version (the version is indicated by a label on the module-containing box with SW20 or
SW12)
you should:
· fit on an updated EEPROM to request from the assistance service centre, stating the code (e.g. 80xxxxx0000 or 46xxxxx0000), the serial number
and the washing machine model.
page 44
n1040064
New SW version introduced on the hybrid module.
-------------------------------------------------------------------------------------------------------------------------------
On AL109XIT (22360), AL89XIT (22362), AL68XIT (22363), AB108XIT (22443) and AB88XIT (22444) Washing machines, some EEPROMs are
used with the modified software.
The modification of the EEPROM has led to the use of new instruction manuals which keep the same SAT part nos. as the pre-modification ones,
whose stocks have been eliminated.
n1040066
LB2000 Hardware (Serial Spanner and Pliers)
-------------------------------------------------------------------------------------------------------------------------------
As of 05.04.2000, the following Spare Parts are available from the Warehouse:
Part no.066055 - Serial spanner for LVB2000 autotest. It has not to be linked to PC. (substituted with 077454);
page 45
Part no. 077454 - Serial spanner for LVB2000-PC White (substituted with 084566);
Part no. 084566 - Serial spanner forLB2000/EVOI -PC BIANCA (substituted with 095669 LB2000/EVOI, EVOII - PC).
n1040078
WARNING: Remove the eeprom
-------------------------------------------------------------------------------------------------------------------------------
Remove the eeprom with pliers part no. 066292 from the faulty module and insert it on the new module / display module, otherwise the machine
will not function.
L'EPROM contains the software that characterizes the model, therefore each apparatus should have his own specific eprom(see the list spare
parts).
n1040087
Interchangeability of electrovalves.
-------------------------------------------------------------------------------------------------------------------------------
Electrovalve part no. 064535 is interchangeable with part no. 066518.
Part no. 064535 will continue to be handled until stock run out.
n1040191
Integrated probe on washing resistance.
-------------------------------------------------------------------------------------------------------------------------------
From the registration no. 10312.0001 on Washing machines produced in the Comunanza Factory Plant, in relation to the present Notice, the
probe's housing hole has been eliminated from the tub cover (application of the thermostat tap hole code 020181), the same has been performed
directly on the resistance.
page 46
The new items interested by the modification are :
Code 081653 - Integrated probe on resistance (for ohmmici values, see enclosed figure);
Code 081837 - Resistance 1700W / 230 V with thermo fusible + adjustable thermostat bulb hole L= 169,5 mm;
Code 081654 - Resistance 1700W / 230 V with thermo fusible + adjustable thermostat bulb hole L = 212,5 mm.
The pre-modification items are not individually interchangeable with the modified ones and as much will continue to be normally handled.
For management requirements, tub with cavity probe/thermostat (until stock depletion) are used and according to necessities, the top cavity
thermostat as above, can be used.
In case of tub modificaton(without cavity) on equipment pre-modificated: the new resistance with probe cavity, the new probe should be used and
sometimes also the long probe thermostat.
The introduction date of modification especifically for each model, it is visible on the plate of EPROM's description SAT code, which is inserted on
the model's documentation Xpartfinder
n1040192
Module LB2000 without Eeprom.
-------------------------------------------------------------------------------------------------------------------------------
From registration no. 10502.0001, on all the LB2000 Washing machine models, with exception to the Evolution range, the module without Eeprom
code 080981 has been used.
The new module, may be used in place of the above mentioned, that will be handled until stock depletion and that however may be used on pre-
modified models.
page 47
n1040208
New hardware testing plug LB2000 Teverola.
-------------------------------------------------------------------------------------------------------------------------------
From the registration number 10827.0001 on all washing machines LB2000 with program selector, produced in the factory in Teverola, a new
hardware testing plug cod. 084817 is used.
The new plug is not interchangeable with the pre-modified one cod. 064899; so both have to be managed. In case of substitution of the piece of
furniture on am equipment, preceding the registration number 10827.0001, it will be necessary to put on the suitable plug.
This modification of the registration number 10820.0001 is extended to all washing machines and wash-driers with a programs' selector produced
in the factory in Comunanza.
n1040211
Serial cable to connect the hardware key with the PC.
-------------------------------------------------------------------------------------------------------------------------------
To connect the hardware key: LB2000 with the personal computer,you must use
a serial cable, pin to pin 9 pin F/F, to garantee the availability, it was
n1040212
New switch
-------------------------------------------------------------------------------------------------------------------------------
From the registration no. 10507.0001, on all Washing machines produced in the Teverola production and from 10402.0001 on Comunanzaplant a
new switch NA code SAT 075445 has been used in place of the switch NA code SAT 063971.
The new switch differs to the pre-modification switch, which will continue to be normally handled for the Faston type of connections (see enclosed
illustration NT006300).
n1040229
page 48
Items with IDC connectors.
-------------------------------------------------------------------------------------------------------------------------------
From November 2001, in order to improve electrical connections on models produced in Teverola and Comunanza plants, electrical components
supplied with IDC connectors have been applied.
page 49
Code 085193 = PRESSURE SENSOR 1 LEVELS + ANTI-SPILL;
Code 086661 = HEATING ELEMENT FOR PROBE 1700W 230V L= 212.5 mm;
Code 084838 = MODULE (LESS EEPROM) MODULE UNIV. STRIP SW 220 IDC.
Wires with IDC connectors can be found directly on spare parts list of models to be repared.
This change has not affected EEPROM which remain the same.
1 – Find the modified particular into spare parts list of model of interest
2 – Check list of models herebelow given and compare with their serial no.
page 50
AAX126LFR (25699) Matr. 20121.0001;
page 51
AL108XTK (22506) Matr.20121.0001;
page 52
AL88XPT (22482) Matr. 20121.0001;
ALD12UK(26093) Matr.20527.0001;
page 53
W104TXTK (23411) Matr. 20121.000;1
page 54
W165XNL (24764) Matr.20502.0001;
page 55
WD12UK (25057) Matr. 20604.001;
page 56
WS84TXEX (23355) Matr. 20204.0001;
page 57
W73FR (23329) Matr. 20408.0001;
n1040230
Modified shock absorber bracket - Comunanza plant
-------------------------------------------------------------------------------------------------------------------------------
From the registration no. 11107.0001, the washing machines and Washer-Dryers produced in the Comunanza factory Plant, have used modified
shock absorbers with the bracket that fixes onto the cabinet.
page 58
The modification also involved the cabinets in the fixing area that for the shock absorbers represent a different type of slotting (see enclosed figure).
To avoid the proliferation of the codes, the modified cabinets are handled with the same SAT code as the pre-modification, when replacing the
cabinet you will need to check the registration number of the appliance.
In order to perform a proper task the intervention of the cabinet replacement it is recommended, that at least in the initial phase, to keep both the
combination of shock absorbers in stock. The shock absorbers code 066184 and 064503 will continue to be normally handled.
n1040242
Power card with welded eeprom.
-------------------------------------------------------------------------------------------------------------------------------
From serial number 20304.0001, IDC power card with welded eeprom is used to ensure the perfect connection of all parts, in the Comunanza,
Teverola and Brembate factories.
To replace the module with welded eeprom, it will be necessary to use the eeprom indicated in the SAT document of the model concerned.
To replace the module on a unit with welded eeprom (Cod. 084838, 089405, 089404, 089416, 089074, and 090505), both the SAT module and the
eeprom are required, because the latter cannot be reused.
n1040246
Button switch NO
-------------------------------------------------------------------------------------------------------------------------------
From serial number 20302.0001, the button switch NO code 088394 is used instead of the premodified switch NO+NO code 075445 (see attached
illustration) and the button switch SE-NO code 063971 is used instead of the premodified switch SE-NO code 058465 (see attached illustration) on
washing machine AL68XPT .
Both switches are regularly managed, therefore in case of repair the serial number of the unit must be taken into consideration.
page 59
This modification also regards the wiring code 088448 which as with all the LB 2000 models, is managed only by request, i.e. without stock, in
order to always manage the interchangeable one with the last modification.
Due to the simplicity of the modification, the images of the wiring diagrams used remain the same as the IDC wiring diagrams already available on
the WEB.
The modification will be also extended to other models which from time to time will be listed below.
page 60
AL109XIT (22360) Matr. 20318.0001;
page 61
ALS68XIT (22473) Matr. 20311.0001;
page 62
W128XSP (24428) Matr. 20318.0001;
page 63
AB43AG (24364) Matr. 20304.0001;
page 64
W44IT (23294) Matr. 20304.0001;
n1040255
Elimination of post-luminescence.
-------------------------------------------------------------------------------------------------------------------------------
Elimination of post-luminescence at end of cycle on LB2000 ARISTON / INDESIT washing machines equipped with IDC wiring.
page 65
In case of post-luminescence at the end of cycle in the Ariston / Indesit LB 2000 washing machines, the following procedure must be carried out
during the intervention phase:
1) Cut approx. 10 cm of the lamp connector wires on the washing machine wiring.
2) Connect the two wires of the specific IDC connector code 089026 (see attached illustration) to the washing machine wiring and check for perfect
insulation after finishing taping;
3) Connect the new lamp code 089024 for Indesit or code 089025 for Ariston and refit it on the panel.
n1040276
Power supply cable + integrally moulded filter.
-------------------------------------------------------------------------------------------------------------------------------
All appliances produced in the Comunanza (from serial no. 21008.0001), Teverola (from serial no. 21111.0001) and Brembate (from serial no.
21119.0001) factories have been equipped with power supply cables with integrally moulded filter (see fig.1 - 1A and 1B) and new units having a
specific opening at the back for fixing the new cables (see fig. 1 - 1C).
The new units, together with the new cables, can be used in place of the premodification ones, by connecting the wiring to the cable, as shown in
figure 1 - 1D.
The codes of the new units and of those replaced (ESI - table n1040276fig02), which will be managed until stocks run out, are given below.
page 66
Code 091632 - Power supply cable 3x1 schuko 1.5m+capacitance filter;
IMPORTANT: the fixing / continuity screw is a specific self-scraping screw (code 092348) that ensures earth continuity between the filter and the
unit. The same screw must be refitted in order to guarantee machine conformity.
page 67
The premodification wirings, are also managed for modified products by making the connection to the terminal block of the new cable as shown in
fig. 1 - 1D.
n1040282
New drainage OKO system.
-------------------------------------------------------------------------------------------------------------------------------
From serial number 21219.0001, the new "OKO" drainage system has been introduced on the washing machines produced in the Comunanza
factory.
The last two numbers of the Industrial Code (located on the rating plate) of the models relevant to this note will be 30 (e.g. 80233560130 - see
Appendix A)
N.B. The industrial code will not change on the models with induction motor (see following list).
page 68
MODEL INDUSTRIAL CODE
ABS53XIT 80224800000
AB54XPT 80224870100
AB63XEX 80225100100
ABS63XEU 80225180100
WS44XIT 80233440100
WS431TXEX 80233470100
WS642TXEX 80233540100
W63XSP 80233890000
AB53XEU 80238820000
AB65XEU 80238830000
AL 64XSP 80239020100
WS43XIT 80244510000
WS53XIT 80244520000
WH66TXE 80253750100
ABS63XEO 80263900000
- EEPROM (the OKO system requires a new setting of load timing parameters). THE NEW EEPROMS REPLACE ALL THE ONES CODED
PREVIOUSLY.
- OKO PUMP BOWL BLOWER + BALL (see fig. 2A, 2B and 2C);
- HOPPER (shifted in front of detergent loading tube connection). Fig. 3A post-modification. Fig. 3B premodification);
page 69
In particular, the OKO system consists of a spherical plastic component inserted in the tube that connects the bowl to the drain pump (see fig.2 A).
At the beginning of each wash cycle the washing machine fills water for 10 seconds and activates the drain pump for 2 seconds. In this way, the
water level in the bowl is different from that in the drain tube; this difference increases the thrust of the ball upwards, closing the bowl-pump
connection tube hermetically (see fig. 2D).
1) separating the wash water and the water in the drain hose, thus saving energy during the heating phase;
With the introduction of this new component, the detergent collecting tube is no longer required and the pump has one hole only to convey water
from the tank.
For the correct operation of the OKO system, it is important that the drain hose of the washing machine remains fixed to the back of the unit with a
plastic clamp (to this end, the clamp withstands a 25 kg load; see reference 1 in fig. 4); otherwise, the drain hose must absolutely reach the height
of the clamp. (minimum 60 cm.)
n1040286
Shock absorbers with 8.15 mm fixing hole.
-------------------------------------------------------------------------------------------------------------------------------
From serial number 30127.0001, for appliances produced in the Comunanza factory, the shock absorbers will be fixed to the tank unit cradle using:
the 8 mm diameter screw code 093750 in place of the 10 mm screw code 030446, and related locking nut code 030443 in place of code 030680.
page 70
The premodified shock absorbers code 086515 and 086372 will continue to be used, whereas cradles code 064518 and 066074 will be used until
stocks run out, after which they will be replaced with the new items after widening the shock absorber fixing holes to a diameter of 11 mm.
page 71
Electric schemes and links
Cod. ce006000
page 72
Legend
Legend: ce006000
EF/P Electro-Valve Cold Water / Prewash P1 1st level pressure cut-off switch
page 73
IC Switch N.C. - 1/2 Load TB Low Temperature Thermostat
page 74
Electric schemes and links
Cod. ce041400
page 75
Legend
Legend: ce041400
EF/P Electro-Valve Cold Water / Prewash P1 1st level pressure cut-off switch
page 76
IC Switch N.C. - 1/2 Load TB Low Temperature Thermostat
page 77
Electric schemes and links
Cod. lg002900
page 78
page 79
Legend
Legend: lg002900
EF/P Electro-Valve Cold Water / Prewash P1 1st level pressure cut-off switch
page 80
IC Switch N.C. - 1/2 Load TB Low Temperature Thermostat
page 81
Electric schemes and links
Cod. se025800
page 82
Legend
Legend: se025800
EF/P Electro-Valve Cold Water / Prewash P1 1st level pressure cut-off switch
page 83
IC Switch N.C. - 1/2 Load TB Low Temperature Thermostat
page 84
Electric schemes and links
Cod. se104200
page 85
Legend
Legend: se104200
EF/P Electro-Valve Cold Water / Prewash P1 1st level pressure cut-off switch
page 86
IC Switch N.C. - 1/2 Load TB Low Temperature Thermostat
page 87