W10444925 PDF
W10444925 PDF
W10444925 PDF
TECHNICAL EDUCATION
2013 NEW DESIGN
15 & 18 UNDER COUNTER
ICE MAKERS WITH FILTER
This Job Aid, 2013 KitchenAid, Maytag and Whirlpool New Design 15 & 18 Under Counter Ice Makers with
Filter, (Part No. W10444925), provides the In-Home Service Professional with information on the installation,
operation, and service of these 2013 ice makers only. For specific information on the model being serviced,
refer to the Use and Care Guide, or Tech Sheet provided with the ice maker.
The Wiring Diagrams used in this Job Aid are typical and should be used for training purposes only. Always use
the Wiring Diagram supplied with the product when servicing the ice maker.
n i
TABLE OF CONTENTS
SECTION 1 - GENERAL INFORMATION
Ice Maker Safety ............................................................................................................................1-2
Model Numbers.............................................................................................................................1-4
Model & Serial Number Label ........................................................................................................1-5
Tech Sheet Location .......................................................................................................................1-5
Dimensions....................................................................................................................................1-6
SECTION 2 - INSTALLATION
Ice Maker Safety ............................................................................................................................2-2
Unpack the Ice Maker ....................................................................................................................2-3
Location Requirements ..................................................................................................................2-3
Electrical Requirements .................................................................................................................2-4
Water Supply Requirements ..........................................................................................................2-4
Vacation or Extended Time Without Use ........................................................................................2-4
Connect Water Supply ...................................................................................................................2-4
Ice Maker Drain Pump Installation (on some models) ....................................................................2-5
Drain Connection ...........................................................................................................................2-8
Ice Maker Door Reversal - Side Swing Only ....................................................................................2-9
Leveling .......................................................................................................................................2-11
Cleaning ......................................................................................................................................2-11
n ii
SECTION 4 - Theory of Operation
Operating System ..........................................................................................................................4-2
Refrigeration System ..................................................................................................................4-2
Water System .............................................................................................................................4-4
Electrical System ........................................................................................................................4-4
Operational Modes ....................................................................................................................4-5
n i
GENERAL INFORMATION
Section 1:
General Information
Model Numbers
Dimensions
n 1-1
GENERAL INFORMATION
Ice Maker Safety
WARNING
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
1-2 n
GENERAL INFORMATION
MS Ice Maker Safety (cont.)
WARNING WARNING
Excessive Weight Hazard
Use two or more people to move and install ice maker.
Failure to do so can result in back or other injury.
n If the drain hose is not aligned over the drain, move the ice maker to align thePlug
drain.into a grounded 3 prong outlet.
NOTE: Service technicians cannot repair plumbing problems outside of the ice Domaker.
not remove ground qualified
Call a licensed, prong.
plumber.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
0%2&/2-!.#%$!4!3(%%4
Electrical Shock Hazard
fire, or electrical shock.
Disconnect power before servicing.
Ice Maker
Replace Water
all parts and panelsFiltration System
before operating.
del P6GEG2KL, P6KG2KL, P6WG2KL Capacity 2000 Gallons (7571 Liters)
Failure to do so can result in death or electrical shock.
n 1-3
GENERAL INFORMATION
Model Numbers
1-4 n
GENERAL INFORMATION
Model & Serial Number Labal
MODEL &
SERIAL
NUMBER
LABEL
Zs>sEd,E/>d^,d
Tech Sheet Location
ts
d^
n 1-5
> Zz^d>/D,/Ed
GENERAL INFORMATION
Dimensions
Notes
1-6 n
INSTALLATION
Section 2:
Installation
This section provides installation information concerning
2013 New Design 15 and 18 Ice Makers.
Location Requirements
Electrical Requirements
Drain Connection
Leveling
Cleaning
n 2-1
INSTALLATION
User Guide
Unpack the Ice Maker ..................................................................2-3
Location Requirements................................................................2-3
Electrical Requirements ...............................................................2-4
Water Supply Requirements ........................................................2-4
Vacation or Extended Time Without Use.....................................2-4
Ice Maker
Connect Water Supply .................................................................2-4
Ice Maker Drain Pump Installation ...............................................2-5
Drain Connection .........................................................................2-8
LEARN MOREIce Maker Door ReversalSide Swing Only ...............................2-9
In an effort to conserve
Levelingnatural resources, this ice maker includes a condensed2-11
...................................................................................... User Guide. A complete Use and Care
Guide can be downloaded at www.jennair.com/manuals.
Cleaning...................................................................................... 2-11
The model number is located on the inside of the ice maker.
Register your ice maker at www.jennair.com.
2-2 n
Operating Your Ice Maker
How Your Ice Maker Works
When you first start your ice maker, the water pan will fill and the The Ice Making Process
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
INSTALLATION
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
INSTALLATION INSTRUCTIONS
Choose a well ventilated area with temperatures above 55F
ems
Unpack the Ice Maker (13C) and below 110F (43C). Best results are obtained
between 70F and 90F (21C and 32C).
The ice maker must be installed in an area sheltered from the
WARNING elements, such as wind, rain, water spray, or drip.
When installing the ice maker under a counter, follow the
Excessive
Excessive Weight
Weight Hazard
Hazard recommended opening dimensions shown. Place electrical
Use two or more people to move and install
Use two or more people to move and install ice maker. ice maker. and plumbing fixtures in the recommended location as
shown.
Failure
Failure toto do
do so
so can
can result
result inin back
back oror other
other injury.
injury. NOTES:
Check that the power supply cord is not damaged, or
pinched or kinked between the ice maker and the
Removing Packaging
RECOMMENDED SOLUTIONS Materials cabinet.
Check that the water supply line is not damaged, or
If theRemove
drain hose
tapeis and
not aligned over
glue from theice
your drain, move
maker the ice
before maker to align the drain. pinched or kinked between the ice maker and the
using.
NOTE: Service technicians
To remove cannot tape
any remaining repairorplumbing
glue fromproblems outside
the exterior cabinet.
of the ice maker.
of the Call a licensed, qualified
plumber.ice maker, rub the area briskly with your thumb. Tape or glue Check that the drain line (on some models) is not
residue can also be easily removed by rubbing a small damaged, or pinched or kinked between the ice maker
amount of liquid dish soap over th e adhesive with your and the cabinet.
fingers. Wipe with warm water and dry. Check that the ice maker door is not flush with the front of
mance Data Sheet
Do not use sharp instruments, rubbing alcohol, flammable
standard cabinets to avoid problems with opening the ice
maker door.
fluids, or abrasive cleaners to remove tape or glue. Do not
use chlorine bleach on the stainless steel surfaces of the ice
IceThese
maker. Maker Water
products Filtration
can damage System
the surface of your
del P6GEG2KL, P6KG2KL,
ice maker. P6WG2KL Capacity 2000 Gallons (7571 Liters)
rk of NSF International.
2
n 2-3
INSTALLATION
The pressure of the water supply coming out of a reverse
on
Electrical Requirements osmosis system going to the water inlet valve of the ice
maker needs to be between 30 and 120 psi (207 and
827 kPa).
WARNING If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
NOTE: The reverse osmosis system must provide 1 gal. (3.8 L) of
water per hour to the ice maker for proper ice maker operation. If
a reverse osmosis system is desired, only a whole-house
capacity reverse osmosis system, capable of maintaining the
steady water supply required by the ice maker, is recommended.
Electrical Shock Hazard Faucet capacity reverse osmosis systems are not able to
Plug into a grounded 3 prong outlet. maintain the steady water supply required by the ice maker.
If the water pressure to the reverse osmosis system is less than
Do not remove ground prong. 40 to 60 psi (276 to 414 kPa):
Do not use an adapter. Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
Do not use an extension cord.
Allow the storage tank on the reverse osmosis system to refill
Failure to follow these instructions can result in death, after heavy usage.
fire, or electrical shock. If you have questions about your water pressure, call a licensed,
qualified plumber.
Before you move your ice maker into its final location, it is
important to make
RECOMMENDED
connection:
sure you have the proper electrical
SOLUTIONS Vacation or Extended Time Without Use
Check When you will not be using the ice maker during the summer
A that
115 itvolt,is plugged
60 Hz., into a grounded
AC only, 3 prong outlet.
15- or 20-amp electrical supply, months, turn off the water and power supply to the ice maker.
properly grounded
Check that the control is turned on.in accordance with the National Electrical
Code and local codes and ordinances, is required. Make sure the water supply lines are protected against
Replace freezing conditions. Ice formations in the supply lines can
It is the fuse or resetthat
recommended the acircuit
separatebreaker.
circuit, serving only your ice
increase water pressure and cause damage to your ice maker
NOTE: maker, be provided.
If problems continue,Usecontact
a receptacle which cannot be turned off
an electrician.
or home. Damage from freezing is not covered by the warranty.
by a switch or pull chain.
Room temperature must be above 55F (13C). Otherwise, bin thermostat may sense cold room temperature
IMPORTANT: If this product is connected to a GFCI (Ground
and shut off even though the bin is not full of ice. The ice maker may not restart once it does shut off.
Fault Circuit Interrupter) equipped outlet, nuisance tripping of the Connect Water Supply
power
If there was supply
a large mayamountoccur, resulting
of water addedin loss of ice
to the cooling.
maker,Ice quality
wait a few minutesReadforall
the drain pump
directions to clear.
before If
you begin.
theremay
is stillbewater
affected.
in theIf bin,
nuisance
checktripping has occurred,
to see whether the drain and if the
hose is kinked. IMPORTANT:
condition of the ice appears poor, dispose of it.
For models with drain pumps, check that the drain hose is not damaged, or kinked or pinched
Plumbing between
shall cabinet
be installed in accordance with the
Recommended Grounding Method
and ice maker. Use only Whirlpool approved drain pump kit, Part Number 1901A.International Plumbing Code and any local codes and
The ice maker must be grounded. The ice maker is equipped with ordinances.
Watera overflowing
power supply thecord
reservoir
having is anormal.
3 prong This overflowplug.
grounding helpsThe
to purge
cord minerals that were removed from the
Use copper tubing or Whirlpool supply line, Part Number
watermust
during bethe ice making
plugged into aprocess.
mating, 3 prong, grounding-type wall
receptacle, grounded in accordance with the National Electrical 8212547RP, and check for leaks.
If there is a whooshing sound, check the following
Code and local codes and ordinances. If a mating wall receptacle things: Install tubing only in areas where temperatures will remain
Makeis notsure available,
that theit is the personal
water supply is responsibility
hooked up and ofturned
the customer
on. to above freezing.
have a properly grounded, 3 prong wall receptacle
Make sure that the drain cap is tight and the water drain pan pump is securely
installed by a Toolsattached
Neededto the water pan.
qualified electrician.
Gather the required tools and parts before starting installation:
If there is ice between the evaporator plate and the cutting grid, check that the ice maker is level. If the ice
maker is level, and the problem persists, run a cleaning cycle. Flat-blade screwdriver
Water Supply Requirements " and " open-end wrenches or two adjustable wrenches
If theCheck
ice maker thatisthe
connected
water supplyto a water supply
lines are pressure
insulated in excess
against of 60 psi, you may hear a loud sound during
freezing " nut driver
waterconditions.
filling associated with the flow
Ice formations in theofsupply
water through
lines can theincrease
inlet valve. Call a licensed,
water qualified plumber to
determine
pressure the andbest damage
method to reduce
your the supply
ice maker waterDamage
or home. pressurefrom NOTE: Do not use a piercing-type or " (4.76 mm) saddle valve
(50 psi is recommended).
frozen supply lines is not covered by the warranty. which reduces water flow and clogs more easily.
A cold water supply with water pressure of between 30 and
120 psi (207 and 827 kPa) is required to operate the ice maker. If Connecting the Water Line
you have questions about your water pressure, call a licensed,
qualified plumber. 1. Turn off main water supply. Turn on nearest faucet long
enough to clear line of water.
Reverse Osmosis Water Supply
2. Using a " copper supply line with a quarter-turn shutoff
IMPORTANT: valve or the equivalent, connect the ice maker as shown.
A reverse osmosis system is not recommended for ice NOTE: To allow sufficient water flow to the ice maker a
makers that have a drain pump installed. minimum " diameter home supply line is recommended.
For gravity drain systems only.
2-4 n
6. Remove and discard the short, black plastic tube from the
end of the water line inlet. INSTALLATION
6. Remove and discard the short, black plastic tube from theby
6.7. Remove
Thread the
end of
nut
andwater
the
onto the
discardline
the short,
end ofblack
inlet.
the tubing.
plasticTighten thethe
tube from nut
hand.
end Then
of the tighten
water line itinlet.
with a wrench two more turns. Do not
7. overtighten.
Thread the nut onto the end of the tubing. Tighten the nut by
7. Thread the nut
hand. Then onto the
tighten enda of
it with the tubing.
wrench two Tighten
more theDo
turns. nutnot
by
NOTE:
hand. To avoid
Then tightenrattling,
it with be sure
a wrench the copper
two more tubing does
turns. Do notnot
overtighten.
touch the cabinets side wall or other parts inside the cabinet.
A overtighten.
B NOTE: To avoid rattling, be sure the copper tubing does not
A NOTE:
touch To
theavoid rattling,
cabinets sidebe sure
wall or the copper
other parts tubing does
inside the not
cabinet.
AB touch the cabinets side wall or other parts inside the cabinet.
B
A. Bulb
B. Nut
A B C D
A. Bulb A. Line to ice maker C. Ferrule (purchased)
A.B.Bulb
3. Now you are ready to connectNut the copper tubing. Use "
A B C D
B. Nut (purchased)
A B C D. Supplied line fromDice maker
B. Nut
(6.35 mm) OD soft copper tubing for the cold water supply. A. Line to ice maker C. Ferrule (purchased)
3. NowEnsure
you are ready to connect the copper tubing. Use " A.B.Line
Nut to ice maker C.D.Ferrule (purchased)
3. Now you that
areOD you
ready to have the proper
connect length
the copper needed
tubing. Use for"
the 8. Install the(purchased)
water supply tube Supplied line fromthe
clamp around icewater
maker supply
(6.35 mm) soft copper tubing for the cold water supply. B. Nut (purchased) D. Supplied line from ice maker
job. Be sure both ends of the copper tubing
(6.35 mm) OD soft copper tubing for the cold water supply. are cut line to reduce strain on the coupling.
square.
Ensure that you have the proper length needed for the 8. Turn
9. Installshutoff
the water
valvesupply tube clamp around the water supply
ON. tube
Ensure
job. Bethat you
sure have
both theofproper
ends lengthtubing
the compression
copper neededarefor the 8. Install
line tothe water supply clamp around the water supply
Slip compression sleeve and nut oncutcopper reduce strain on the coupling.
job. Be sure
square.
tubing both ends
as shown. Insertofendthe of
copper
tubing tubing are cut
into outlet end 10.line to reduce
Check strain
for leaks. on theany
Tighten coupling.
connections (including
square. as far as it will go. Screw compression nut onto 9. connections
Turn shutoff valve
at the ON.
valve) or nuts that leak.
squarely
Slip compression sleeve and compression nut on copper 9. Turn shutoff valve ON.
Slip compression
outlet
tubing end sleeve
Insert and
with adjustable
as shown. end compression
wrench. Dointo
of tubing notnut on copper
overtighten.
outlet end 10. Check for leaks. Tighten any connections (including
tubing as shown. 10. Check for leaks.
connections Tighten
at the any
valve) or connections (including
nuts that leak.
as far asInsert
it willend
go. of tubing into outlet end
squarely
squarely as with
outlet end far asadjustable
Screw
it will go. wrench.
Screw
compression
A compression
nut onto
nut onto
Do not overtighten. Ice Maker
connections Drain
at the valve) Pump
or nuts Installation
that leak.
outlet end with adjustable wrench. Do not overtighten.
A NOTES:
Ice Maker(on somePump
Drain models)
Installation
Ice Maker Drain Pump Installation
AB (on some models)
Connect drain pump
NOTES:
(onto some models)
your drain in accordance with all state
B NOTES:and local codes and ordinances.
B Connect drain pump to your drain in accordance with all state
C It may be
Connect desirable
drain pump to your
insulate drain tube thoroughly upstate
to
and local
drain inlet codes andtoordinances.
to minimize
drain in accordance
condensation on the drain tube.
with all
and local codes and ordinances.
C It may be tube
Insulated desirable to insulate
kit Part Numberdrain tube thoroughly
W10365792 up for
is available to
C Itdrain
may be inletdesirable
to minimize to insulate drain tube
condensation thoroughly
on the drain tube.up to
A. Compression sleeve C. Copper tubing purchase.
drain inlet to
Insulated tubeminimize
kit Partcondensation
Number on the drainavailable
W10365792 tube. for
B. Compression nut Drain
Insulated pump
tubeiskit designed
Part Number to pump water to aisis
W10365792 maximum height
available for
A. Compression sleeve C. Copper tubing purchase.
of 10 ft (3 m). Use only Whirlpool approved drain pump kit
A.B.Compression sleeve C. Copper tubing purchase.
4. Place the Compression nut tubing
free end of the into a container or sink, and DrainNumber
Part pump is1901A. designed to pump water to a maximum height
B. Compression nut Drain
of 10 pump is designed
ft connect
(3 m). Use onlyend to pump water
Whirlpool approvedto a maximum height
turn on main water supply and flush out tubing until water is ofDo 10 not
ft (3 m). Use outlet
only of drain
Whirlpool approved adrain
tube to drain closedpump
pumppipe kit
kit
4. clear.
Place Turn
the free end of the
off shutoff valvetubing
on the into a container
water pipe. or sink, and Part
system Number
to keep 1901A.
drain water from backing up into the ice
4. Place themain
turn on free end
water ofsupply
the tubingand into
flush a out
container
tubing or sink,
until andis
water Part Number 1901A.
IMPORTANT: Always drain the water line before making the Do not connect outlet end of drain tube to a closed pipe
maker.
turn on main water supply and flush out tubing
pipe. to avoid is
until water Do not connect
clear.connection
final Turn off shutoff
to the valve
inletonon
ofthethe water
the water valve system to keepoutlet drain end
water of from
drainbacking
tube to a upclosed pipe
into the ice
clear. Turn off shutoff valve water pipe. Kitsystem
Contains:
IMPORTANT:
possible water Always drain the water line before making the
valve malfunction. maker.to keep drain water from backing up into the ice
IMPORTANT: Always drain the water linevalve
before maker.
Drain pump kit Part Number 1901A
final
5. final
Bend connection
the copper to the inlet of the water tomaking
avoid the
Kit Contains:
connection
possible water to tubing
valve
to of
inlet meet
themalfunction. the the water
water valveline
toinlet
avoid which is
Kit
Contains:
" ID x 5" drain tube (ice maker bin to drain pump reservoir
located water
possible on thevalve
backmalfunction.
of the ice maker cabinet as shown. Drain pump kit Part Number 1901A
5. Leave
Bend the copper tubingtubing
to meet the water linemaker
inlet which inlet)pump kit Part Number 1901A
Drain
a coil of copper to allow the ice to be is " ID x 5" drain tube (ice maker bin to drain pump reservoir
5. Bend the copper tubing toormeet thefrom
watertheline inlet which is "IDIDx x5"
10 ft (3 m) drain
located
pulled on
out the
of theback of the
cabinet ice
away maker cabinet wallas shown.
for service. "
inlet) drain tube (icetube hose
maker bin(drain pump
to drain pumpdischarge
reservoir to
located
Leave aoncoiltheofback
copperof the ice maker
tubing to allow cabinet
the iceasmaker
shown. to be household drain)
inlet)
Leave
pulled a out
coilofofthe
copper tubing
cabinet to allow
or away fromthetheicewall
maker to be
for service. " ID x 10 ft (3 m) drain tube hose (drain pump discharge to
Rear View IDID
"
" x 32"
x 10 (3(81
ftdrain) m)cm)
drainvent tube
tube (drain
hose pump
(drain pump reservoir venttoto
discharge
pulled out of the cabinet or away from the wall for service. household
ice maker
household drain) cabinet back)
Rear View " ID x 32" (81 cm) vent tube (drain pump reservoir vent to
Cable
Rear View iceID
" xclamps
maker (81(secures
32"cabinet ventvent
cm)back) tubetube
(drainto pump
back of ice maker)
reservoir vent(3)to
ice maker
#8-32 cabinet
x " pumpback) mounting screws (secures drain pump to
A Cable clamps (secures vent tube to back of ice maker) (3)
baseplate
Cable clamps and(secures
clampsvent to back
tubeoftoice maker)
back of ice (5)maker) (3)
#8-32 x " pump mounting screws (secures drain pump to
"
#8-32 small adjustable
x " and
pump hose
mounting clamp
screws (secures
(secures vent to drain pump)
maker)drain(5) pump to
A
AB baseplate clamps to back of ice
baseplate and clampshose
" large adjustable to back of ice
clamp, maker)drain
(secures (5) tube to ice
" small adjustable hose clamp (secures vent to drain pump)
B "maker
smallbin and drainhose
adjustable pump reservoir
clamp (securesinlet)vent
(3) to drain pump)
B " large adjustable hose clamp, (secures drain tube to ice
Rear panel
largebin (2)
adjustable hose clamp, (securesinlet)drain
(3) tube to ice
"maker and drain pump reservoir
maker bin and
Instruction sheet drain pump reservoir inlet) (3)
Rear panel (2)
Rear panel (2)
Instruction sheet
C Instruction sheet
C
C
A. Copper tubing C. Inlet water tube clamp and
B. Water supply tube clamp supply line connector
A. Copper tubing C. Inlet water tube clamp and
A.B.Copper tubing tube clamp
Water supply C. Inlet water
supply linetube clamp and
connector
B. Water supply tube clamp supply line connector n 2-5
4
4
INSTALLATION
If Ice Maker Is Currently Installed Drain Pump Installation
If Ice Maker Is Currently Installed Drain Pump Installation
If Ice Maker Is Currently Installed Drain Pump Installation
If IceIfMaker
NOTE: Is Currently
ice maker Installed
is not installed, please proceed to Drain DrainDo
NOTE: Pump Installation
not kink, smash or damage tubes or wires during
IfIf Ice
NOTE: IceIfMaker
Maker Is Currently
Is
ice makerCurrently Installed
Installed
is not installed, please proceed to Drain DrainDo
Drain
NOTE: Pump
Pump Installation
Installation
not kink, smash or damage tubes or wires during
Pump
NOTE:Installation
If ice makersection.
is not installed, please proceed to Drain installation.
NOTE: Do not kink, smash or damage tubes or wires during
Pump
NOTE:Installation
If ice makersection.
is not installed, please proceed to Drain installation.
NOTE: Do not kink, smash or damage tubes or wires during
Pump
1.
NOTE:
NOTE:Installation
PushIf
If the
ice
ice maker
maker section.
selectoris switch
is not to the Off
not installed,
installed, position.
please
please proceed to
proceed to Drain
Drain installation.
1.
NOTE:Unplug
NOTE: ice kink,
Do not
Do not maker
kink, or disconnect
smash
smash or damage
or damage power.
tubes or
tubes or wires
wires during
during
Pump
1. Installation
Push section.
the selector switch to the Off position. installation.
1. Unplug ice maker or disconnect power.
Pump
1.
Pump Installation
Push
Installation section.
the selector switch to the Off position.
section. installation.
1. Unplug ice
installation.
2. Remove rearmaker
panel.orSee
disconnect power.
Rear Panel illustration for 5 screw
1. Push the selector switch to the Off position. 1. Remove
2. Unplug ice rearmaker
panel.orSee
disconnect
Rear power.
away Panel illustration forand
5 screw
1. Push
1. Push thethe selector
selector switch
switch to
WARNING
to the
the Off
Off position.
WARNING
position. 1. locations.
2.
1. Unplug ice
Remove
Unplug
2. locations.
Remove
icePull
rear
rear
rearor
maker
panel.
maker
Pull rear
panel.
panel
or disconnect
See
See
Rear
disconnect
panel away
Rear
from
Panelthe
power.
power.
from
Panelthe
drain tube
illustration
drain tube
illustration
for 5 screw
forand
5 screw
WARNING
WARNING
2. discard.
locations.
2. discard.
Remove rear
Remove
locations.
discard.
Pullpanel.
rear
Pull
rear panel
panel.
rear See
panel
away Panel
See Rear
Rear
away
from
Panel
from
the drain tube
illustration
illustration
the drain tubeforand
for 55 screw
and screw
WARNING Rear
Rear
Rear
Panel Pull
locations.
locations.
discard.
Panel
Panel
discard.
discard.
Pull rear
rear panel
panel away
away from
from the
the drain
drain tube
tube and
and
Rear Panel A
Rear Panel
Rear Panel A
A
A
A
A
C
CD
C A
D
C
D A
D A
E A
E
E A. Drain pump installed
E
A. Drain pump installed
A.
8. Align the 2 screwA. Drain pump
holes installed
G F Drainat the rear
pump of the pump. Use two
installed
8. Align#8-32 thex 2"screw
screws, holes supplied.
at the rearSeeofParts Locations
the pump. Use two
A. Vent tube G G F E. Ice maker unit power cord 8. #8-32
Align the
illustration.
x 2 screw
" screws, holes at the See
supplied. rear Parts
of the pump.
Locations Use two
F 8. Align
#8-32 the
x 2
" screw
screws, holes at
supplied. the rear
See of the
Parts pump.
Locations Use two
" hose
A.B.Vent G
tube clamp F E.F.Ice
#8-32 x
maker " pump
unit mounting
power cord screws 9. illustration.
Connect
#8-32 x "drain
screws, tubesupplied.
to ice maker See bin Partsoutlet (" ID), using "
Locations
A.C.
Vent tube E.G.#8-32
Ice maker illustration.
B.
A. Drain
Vent pump
" hose
tube discharge tube
clamp F.
E.
Drain "unit
xpump pumppower
power cord clamp
cord,
mounting
cord screws adjustable
illustration.
9. Connect drainclamp,
tube supplied.
to ice maker Seebin Drain
outlet Tube illustration.
(" ID), using "
" hose
B.D.Drain
Drain clamp
pump F. Ice maker
#8-32 x "unit
and screw pumppower
mounting screws 9. adjustable
Connect drain tubesupplied.
to ice maker bin outlet ("illustration.
ID), using "
C.
B. pump
" hose discharge
clamp tube G. Drain
F. #8-32 pump power
x " pump cord,
mountingclamp
screws 9.10.Connect
Coil ice drain clamp,
makertube power to cord
ice See Drain
into abin
maker 4" outletTube
(10.2 cm)(" diameter
ID), using coil.
"
C. Drain
D. Drain pump
Drain pump discharge tube G. Drain
and pump
screw power cord, clamp adjustable clamp, supplied. See Drain Tube illustration.
C.
D. Drain pump
pump discharge tube G. Drain pump power cord, clamp
and screw 10. CoilWrap iceelectrical
adjustable clamp,
maker tape
power around
supplied.
cord See
into the power
a Drain
4" (10.2 cord
cm) in
Tube several coil.
illustration.
diameter places
6.Drain Remove
pump power cord clamp andandground
screw screw attached to ice 10. Coil ice maker power cord into
D. 10. Wrapto keep
Coil ice the cord
electrical
maker tape
power in around
acord theaapower
coil. into
Locate 4" (10.2
4"coiled
(10.2 cordcm)
power
cm)
diameter
cord between
indiameter
several coil.
places
coil.
6. maker power
Remove powercord, which is
cord clamp mounted
and ground to the unit
screw base.to
attached See
ice Wrap
the electrical
drain pump tape
and around
side of the power
enclosure cord
and in several
plug into theplaces
6. Remove power cordillustration.
clampisand ground screw attached to ice to
Wrap keep the
electricalcord tapein a coil.
around Locate
the powercoiled power
cord cord
in several between
places
6. Parts
maker
Remove Locations
power
power cord,
cord which mounted to the unit base. See toreceptacle
keep the cord
of the indrain
aside
coil. Locate
pump. Seecoiled
Parts power cord
Locations between
maker Locations
Parts which is mounted to the unit base. Seeice
clamp
power cord,illustration. and ground screw attached to the
to
the
drainthe
keep pump
drain pump cord andin
and a coil.
side
ofLocate
enclosure
of enclosure coiled and plug
power into the
cord
and plug into the between
NOTE: Clamp
maker andwhich
screwiswill be reused. illustration.
Parts power
Locationscord,illustration. mounted to the unit base. See receptacle
the drain pump
receptacle
of theand
of the drain
drainside pump. See Parts
of enclosure
pump. See Parts andLocations
plug into the
Locations
Parts
Slide Locations
7. NOTE: Clamp
drain andillustration.
pump screw
into thewill
icebe reused.
maker base on the right side. 11.illustration.
Attach
receptacle the ofdrain
the pump
drain power
pump. cord
See to
Parts ice Locations
maker unit base with
NOTE: Clamp and screw will be reused. illustration.
The drain
NOTE:
7. Slide pumpClamp mounting
pump andinto tab will
screw
the should
ice slipbase
be reused.
maker into on
thetherectangular
right side.slot clampthe
illustration.
11. Attach anddrain
screw pump (removed
powerincord Step to6)ice that wasunit
maker used to attach
base with
7. The
Slide
in thedrain
pump pump base.
ice mounting
maker intotabthe ice maker
Itshould
will beslip basethe
necessary
into onto the right
tipright side.
the pump
rectangular slot 11. clamp
Attach
ice maker the drain
and power
screw pump power
cord.power
(removed cord
SeeinParts
Stepto to ice maker
Locations
6) thatmaker
was used unit base
illustration. with
to attach
7. Slide
The drain
pump pump
mountinginto the
tab ice
shouldmaker
slip base on
into the the
rectangular side.
slot 11. Attach
clamp the drain
andpower pump
screw cord. (removed cord ice
in StepLocations unit
6) that wasillustration. base
used to attach with
inslightly
The iceto
thepump slip into
maker base.
mounting the
tabItslot.
will Seenecessary
be
should Drain
slip intoPump
the Mounting
torectangular
tip the pump Tab
slot ice
12.clamp maker
Placeand newscrewrear panel (removed See Parts
(smallinoneStepfor 6)15"
thatice wasmakers,
used to large
attachone
in the
Slot
slightly ice maker
illustration.
tomaker base.
slip into It
the slot. will be
See necessary
Drain Pump to tip the
Mounting pumpTab ice maker power cord. See Parts Locations illustration.
in the ice base. It will be necessary to tip the pump formaker
ice
12. Place 18")new against
power
rear panel the
cord. backSeeofParts
(small the for
one ice maker.
Locations
15" Route the
illustration.
ice makers, largevent one
slightly
Slot to slip into the slot. See Drain Pump Mounting Tab
illustration. 12. Place new rear panel (small one for 15" iceRoute makers, large one
Drain
SlotPump
slightly Mounting
to slip
illustration. Tab Slot
into the slot. See Drain Pump Mounting Tab 12. fortube
Place 18") and drain
against
new pump
the
rear panel back discharge
(smallof the
oneice tube
for 15"through
maker. iceRoute
makers, cutouts
thelarge
ventin one
the
Slot
Drain illustration.
Pump Mounting Tab Slot for
rear
tube 18")
and against
panel.drain the back
pump of the
discharge ice
tube maker.
through cutouts the vent
in the
for 18") against the back of the ice maker. Route the vent
Drain Pump Mounting Tab Slot tubepanel.
13.rear
Secure
and drain pump discharge tube through cutouts in the
Drain Pump Mounting Tab Slot tube andrear
rear panel. drain panel
pump with original tube
discharge screws. See Rear
through cutouts Panel
in the
illustration.
rear
13. Secure panel.rear panel with original screws. See Rear Panel
13. illustration.
Secure rear panel with original screws. See Rear Panel
14.Secure
13. Securerear ventpanel
tubewith to back of ice
original makerSee
screws. usingRear3 clampsPaneland
illustration.
three #8-32
illustration.
14. Secure vent tubex "toscrews,
back ofsupplied.
ice maker See Vent
using Tube and
3 clamps
14. Secure vent tube
illustration. to back of ice maker using
Vent3Tube clamps and
14. three
Secure #8-32
three #8-32 vent xxtube
" screws,
to back supplied.
" screws, of ice maker
supplied.
Seeusing
See Vent3 Tube clamps and
illustration.
Vent
three Tube#8-32 x " screws, supplied. See Vent Tube
illustration.
Vent illustration.
NOTE: Tube Do not pinch, kink or damage the vent tube. Check that it
Vent
is not
Tube
damaged, or pinched or kinked between the Check
cabinetthat andit
Vent
NOTE: Tube
Do not pinch, kink or damage the vent tube.
NOTE:
isthe
not ice Do not pinch,
maker.
damaged, or kink oror
pinched damage
kinked the vent tube.
between the Check and
cabinet that it
A NOTE:
is not Do not pinch, kink or damage the vent tube. Check that it
damaged,
the
is maker. or pinched or kinked between the cabinet and
icedamaged,
A thenot
ice maker. or pinched or kinked between the cabinet and
A the ice maker.
A A
A
A
A. Mounting tab slot A
A. Mounting tab slot
A. Mounting tab slot
A. Mounting tab slot
B
B
B
B
A. Vent tube
A.B.Vent
Clamps
tube and screws
A. Clamps
B. Vent tubeand screws
A.
B. Vent
Clampstube
and screws
B. Clamps and screws
n 2-7
6
6
6
Solver
INSTALLATION
code at left with your mobile device, or visit https://jennair.custhelp.com for
endations that may
15. Attach " IDhelp
x 10 ftyou
(3 m)avoid a service
drain tube call.
to pump discharge tube. The ideal installation has a standpipe with a 1" (3.81 cm) to
See Parts Locations illustration. 2" (5.08 cm) PVC drain reducer installed directly below the
NOTE: Do not connect outlet end of drain tube to a closed outlet of the drain tube as shown. You must maintain a
1" (2.54 cm) air gap between the drain hose and the
pipe system to keep drain water from backing up into the ice
standpipe.
maker.
IMPORTANT: A drain pump is necessary when a floor drain is not
16. Connect ice maker to water supply and install ice maker as available. A Drain Pump kit, Part Number 1901A, is available for
on specified by the product installation instructions. purchase.
17. Check all connections for leaks.
Side View
WARNING
B
Electrical Shock Hazard
1"
Plug into a grounded 3 prong outlet. (4.8 cm)
1" (2.54 cm)
Do not remove ground prong.
Do not use an adapter. 23" C
(58.4 cm)
Do not use an extension cord. D
2" - 1"
Failure to follow these instructions can result in death, (5 cm - 3.8 cm)
fire, or electrical shock.
A. Drain hose D. Center of drain should be 23" (58.4 cm) from
B. 1" (2.54 cm) air gap front of door, with or without the "
(1.91 cm) panel on the door. The drain should
18. Plug in ice maker or reconnect power. C. PVC drain reducer also be centered from left to right (7"
RECOMMENDED SOLUTIONS
19. Turn on ice maker. [18.56 cm] from either side of the ice maker).
20.
Check Wait
that it isfor rinsing into
plugged cycle, approximately
a grounded 5 minutes,
3 prong outlet. to be sure the
ice maker is operating properly.
Check that the control is turned on. Drain Pump System (on some models)
2-8 n
the code at left with your mobile device, or visit https://jennair.custhelp.com for
mmendations that may help you avoid a service call.
INSTALLATION
Connecting the
Connecting the Drain
Drain Remove Stainless
Remove Stainless Steel
Steel Door
Door Wrap
Wrap Panel
Panel
On Some Models
On Some Models
After ensuring that the drain system is adequate, follow these
ation After ensuring that the drain system is adequate, follow these
steps to properly place the ice maker:
steps to properly place the ice maker:
WARNING
WARNING
te WARNING
WARNING
Check that it is plugged into a grounded 3 prong outlet.
3. Rotate the door wrap panel until it separates from the door
3. Rotate the door wrap panel until it separates from the door
and pull up.
and pull up.
NOTE: Be sure the edge guards do not separate from the
Excessive
Check that the control is Excessive Weight Hazard
turned on. Weight NOTE: Be sure the edge guards do not separate from the
Hazard door wrap panel.
door wrap panel.
ReplaceUse Use two or
the fuse more people
or reset tobreaker.
move and install ice maker.
two or morethe circuitto
people move and install ice maker.
NOTE: IfFailure
problems to do so cancontact
continue, result anIce
in back Production
or other injury.
electrician.
Failure to do so can result in back or other injury.
Door Stop
Door Stop and and End-Cap
End-Cap Reversal Reversal
Room temperature must be above 55F (13C). Otherwise, bin thermostat may sense cold room temperature
2. Style
and shut off even
2. Style
RECOMMENDED
1For
1For though
so
gravity
gravity
that the
drain
the bin is not
drain
ice maker
system,
system,
push
full ofpush
ice. The
position so that the ice maker drain tube is positioned over
position SOLUTIONS drain tube
the ice maker
the ice
is
maker into not restart once it does shut off.
ice maker may
positioned
into
over
WARNING
WARNING
If there was the aPVC large amount
drain of water
reducer. See added
Gravity to Drain
the iceSystem.
maker, wait a few minutes for the drain pump to clear. If
there thewater
PVC drain reducer. See Gravity Drainthe System.
If the is still
drainStylehose isinnot
2For
thealigned
bin, check
drain pump
tothe
oversystemsee whether
drain, move the
connect thedrain hose istokinked.
ice maker
drain pump align the drain.
Style 2For drain pump system connect the drain pump
NOTE:
For models outlet
Service hose topumps,
technicians the drain.
cannot See Drain
repair Pump
plumbing System.
problems outside of the ice maker. Call a licensed,
between qualified
outlet hose to the drain. See Drain Pump System. damaged,
with drain check that the drain hose is not or kinked or pinched cabinet
and ice
3. maker.
plumber. Recheck Usethe only
iceWhirlpool
maker toapproved
be sure that drain pump
it is level.kit,See
Part Number 1901A.
3. Recheck the ice maker to be sure that it is level. See
Leveling.
Leveling.
Water overflowing the reservoir is normal. This overflow helps to purge minerals that were removed from the
water4.4.during
If it is
therequired
ice making by your local sanitation code, seal the cabinet
process.
If it is required by your local sanitation code, seal the cabinet
mance Data Sheet to the floor with an approved caulking compound after all
to the floor with an approved caulking compound after all
water
If there iswater and electrical
a whooshing sound,connections
check the
and electrical connections have been made.
have been
following made.
things:
Electrical Shock Hazard
Electrical
Electrical Shock
Disconnect power before servicing.
Shock Hazard
Hazard
Make sure that the water supply is hooked up and turned on.
Disconnect
Disconnect power power before
before servicing.
servicing.
Replace all parts and panels before operating.
Make Icesure
Ice Maker
IcethatMaker
Maker Door
theDoor ReversalSide
drain Water is tightFiltration
ReversalSide
cap and the waterSystem Swing
Swing Only
drain panOnly pump is securely Replace
Replace
attachedall parts
all to the and
parts and panels
water pan. before
panels before operating.
operating.
del P6GEG2KL, Tools P6KG2KL,
Needed P6WG2KL Capacity 2000 Gallons (7571 Failure
Liters)to do so can result in death or electrical shock.
Tools
If there is ice Needed
between the evaporator plate and the cutting grid, check that the ice Failure
makerto
Failure toisdo
do so
so can
level. can
If theresult
ice in
result in death
death or or electrical
electrical shock.
shock.
maker Gather
is level,theand required
the tools and
problem partsrun
persists, before
a startingcycle.
cleaning installation.
Gather the required tools and parts before starting installation.
" wrench System tested and Flatcertified
putty knifeby NSF 1. Unplug the ice maker or disconnect power.
If the ice
maker is connectedInternational
to a water supply
Flat pressure in excess of 60 psi, you 1. Unplug
may hear thea ice maker orduring
disconnect power.
" wrench against
PROBLEM
putty
NSF/ANSI knife 2. Remove
RECOMMENDED theloud sound
handle
SOLUTIONS screws and handle (on some models).
water filling"associated
wrench with Standard the flow of42water through
for Phillips the inlet
screwdriver
the reduction of valve. Call a 2. Remove
licensed, the
qualified handle
plumber screws
to and handle (on some models).
" wrench Phillips screwdriver 3. Remove the hinge pin from the top hinge.
determine the best method to reduceTaste
Chlorine theMaker
Ice supply
and Odor.waterBut
Runs pressure (50 psi Check
Produces is recommended).
3. that
Remove the hinge
the control is turnedpin from
on. the top hinge.
No Ice 4. Remove the door from the hinges and replace the top hinge
4. Remove the door from the hinges and replace the top hinge
sted according to NSF/ANSI Standards 42 for the reduction of the substances listed Checkbelow. pin.
that the
The water supply
concentration is
of properly
the connected and turned on.
water entering the system was reduced to a concentration less than or equal to the permissible pin. limit for water leaving the
5.
If the5.drainRemove the
cap is the
loose,screw
water and door
willdoor
emptystop at
from corner A. pan,
the water Remove the
and the
you will have
SF/ANSI Standards 42. Remove screw and stop at corner A. Remove
the drain screw
cap. and end cap at corner C. Place the door stop at corner
F Reduction Average Influent Challenge Maximum Average screw and
Minimum end cap at corner C. Place the door stop at corner
C, and tighten%screw. Average
Place%the end cap at corner A, and
quirements Influent Hinge HingeConcentration
pin "" hex-head
Effluent hinge screw
hex-head Effluent C, and tighten screw.
Reduction Place the end cap at corner A, and
Reduction
pin hinge screw tighten
Clean thetighten screw.
drain tube.
% reduction 1.9727 mg/L 2.0 mg/L 10% 0.71 mg/L 0.7788 mg/L 70.2screw. 72.81
Check
0.5 unless otherwise noted. Flow = 0.50 gpm (1.89 Lpm). Pressure = 60 psig (413.7 kPa).that there are no kinks in the drain line.
C to 22C). Rated service capacity = 2000 gallons (7571 liters).
onal, maintenance, and filter replacement Ice Maker
ReferRuns But
to the Producessection
Warranty If theforaccelerated ice production
the Manufacturers limited feature is turned on, this feature increases the
out for the product to perform as advertised.
Handle screw Very Little Ice
warranty.
End cap screw you with more ice in the same amount of time.
6RFWG2K, P6RFGEG2K,Handle screw Part
P6RFKG2K, End cap screw
Room temperatures
Application Guidelines/Water of more than 90F (32C) will normally reduce ice product
Supply Parameters
n 2-9
r filter status display changes from GOOD Water Supply Dirt orCity
lint or
mayWell
be blocking the airflow through the condenser.
w filter. When the filter indicator reads Water Pressure 30 - 120 psi (207 - 827 kPa)
mended that you replace the filter. If there
Water Temperature 33is -white
100Fscale
(0.6buildup in the ice makers water or freezing system, you s
- 37.8C)
8
o check the status of your water filter. If the
INSTALLATION
6.
6. Remove
Remove thethe screw
screw and
and door
door stop
stop at
at corner
corner D.
D. Remove
Remove the
the Top
Top Hinge
Hinge
screw
screw and
and end
end cap
cap at
at corner
corner B.
B. Place
Place the
the door
door stop
stop at
at corner
corner
B,
B, and
and tighten
tighten screw.
screw. Place
Place the
the end
end cap
cap at
at corner
corner D,
D, and
and
tighten
tighten screw.
screw.
A
A
A
A B
B B
B
C
C
6. Remove the screw and door stop at corner D. Remove the Top Hinge
screw and end cap at corner B. Place the door stop at corner D
D
B, and tighten screw. Place the end cap at corner D, and
tighten screw.
A
A B B E
E
A.
A.Hinge
Hinge pin
pin D.
D.Hinge
Hinge C
B.
B.Phillips-head
Phillips-head countersink
countersink screw
screw E.
E.Hex-head
Hex-head hinge
hinge
D screw
screw
C.
C.Hinge
Hinge pin
pin sleeve
sleeve
D
D C
C
Bottom E
Bottom Hinge
Hinge
A.
A.Top
Top corner
corner open
open (no
(no end
end cap)
cap) C.
C.Beginning
Beginning bottom
bottom corner
corner end
end cap
cap
B.
B.Beginning
Beginning top
top corner
corner end
end cap
cap D.
D.Bottom
Bottom corner
corner open
open (no
(no end
end cap)
cap)
A. Hinge pin D. Hinge
B. Phillips-head countersink screw E. Hex-head hinge screw
7.
7. Depending
Depending on on your
your model,
model, thethe brand
brand badge
badge forfor the
the front
front door
door C. Hinge pin sleeve
of
of your
your ice
ice maker
maker may
may be be in
in the
the package
package
D with
with the
C Use
the Use and
and A
A
Care
Care Guide.
Guide. Fasten
Fasten thethe brand
brand badge
badge to to the
the door.
door. Bottom Hinge
A. Top corner open (no end cap) C. Beginning bottom corner end cap
8. Set the door aside.
8. Set the door aside.
B. Beginning top corner end cap D. Bottom corner open (no end cap)
7. Depending on your model, the brand badge for the front door
Reverse
Reverse Hinges
Hinges of your ice maker may be in the package with the Use and A B
B
Care Guide. Fasten the brand badge to the door.
1.
1. Unscrew
Unscrew and
and remove
remove the
the
8. Set the top
top
door hinge.
hinge. Replace
aside. Replace thethe screws
screws in in
the
the empty
empty hinge
hinge holes.
holes.
Reverse
2.
2. Remove
Remove the the screws
screws fromHinges
from the
the bottom
bottom of of the
the opposite
opposite sideside of
of B C
C
the ice maker cabinet.
the ice maker cabinet.
1. Unscrew Turn
Turnandthethe top
topthe
remove hinge
hinge upside
upside
top hinge. down
down
Replace so
theso
screws in
that
that the
the hinge
hinge pin points
pinthe emptyup.
points up.
hingePlace
holes.the
Place the hinge
hinge onon the
the bottom
bottom D
D
opposite
opposite side
side of2. the
of the ice
ice maker
Remove maker
the screws and
and tighten
tighten
from screws.
screws.
the bottom of the opposite side of C
3. the ice maker cabinet. Turn the top hinge upside down so
3. Remove
Remove the the old bottom
oldthat
bottom hinge
the hingehinge screws
screws
pin points
and
up. and
hinge.
Placehinge.
Replace
the hingeReplace
on the bottom
E
E D
the
the screws
screws in in the empty
empty hinge
the opposite hinge holes.
holes.
side of the ice maker and tighten screws. A.
A.Hex-head
Hex-head hinge
hinge screw
screw D.
D.Hinge
Hinge pin
pin
4.
4. Remove
Remove the the screws
screws from
fromthe
3. Remove the
the top
old of
of the
topbottom opposite
thehinge screwsside
opposite side of
of the
the
and hinge. Replace B.
B.Hinge
Hinge pin
pin sleeve
E
sleeve E.
E.Hinge
Hinge
ice
ice maker
maker cabinet.
cabinet. the screws
Turn
Turn theinhinge
the the empty
hinge hingedown
upside
upside holes. so
down so that
that the
the C.
C.Phillips-head
Phillips-head countersink
countersink
A. Hex-head hinge screw screw
screw D. Hinge pin
hinge
hinge pin
pin points
points 4. down.
RemovePlace
down. the screws
Place the from the
the hinge
hinge ontop
on of the
the
the topopposite
top oppositeside of the
opposite B. Hinge pin sleeve E. Hinge
ice maker cabinet. Turn the hinge upside down so that the C. Phillips-head countersink screw
side
side of
of the
the ice
ice maker
maker and
and tighten
tighten the
the screws.
screws.
hinge pin points down. Place the hinge on the top opposite
5.
5. Remove
Remove the the top
top hinge
side ofpin.
hinge the ice maker and tighten the screws.
pin. Reverse
Reverse Door
Door Catch
Catch
5. Remove the top hinge pin. Reverse Door Catch
Replace 1.
1. Remove
Remove the the white
white decorative
decorative screws
screws fromfrom the
the opposite
opposite side
side
Replace Door
Door Replace Door 1. Remove the white decorative screws from the opposite side
of
of the
the door
door
of the
and
doorand
set
and set
aside.
aside.
set aside.
1.
1. Place
Place the
the door
door1.on the
the bottom
onPlace bottom
the hinge
hinge
door on pin.
pin. hinge pin.
the bottom 2.
2. Remove
Remove
2. Remove the
thethescrews
screws from
from
screws from the
thethe magnetic
magnetic
magnetic door
door catch catch
catch and
doorand and
2. replace
replace itit on
replace onthe
iton the opposite
the opposite
opposite side
side of
of the
side the
the door.
of door. door.
2. Align
Align the
the door with
door 2.
with the
Align top
thethe hinge
door
top hole
with the
hinge topand
hole replace
hinge
and hole andthe
replace top
replace
the topthe top
hinge hinge pin.
hinge pin.
pin.
3. Replace the handle and handle screws.
3.
3. Replace
Replace the
the handle
handle and handle
handle screws.
andModelsReplace
screws.Door Wrap
On Some
On
On Some
Some ModelsReplace
ModelsReplace Door
wrap Wrap
Door
1. Place the door Wraponto the door top and ensure that
flange
1. it fits correctly.
1. Place
Place the the door
door wrap
wrap flange
flange onto
onto the
the door
door top top and
and ensure
ensure that
that
itit fits 2. Rotate the door wrap downward until it covers the door
fits correctly.
correctly. surface completely.
2.
2. Rotate
Rotate the the door3. wrap
door Installdownward
wrap downward
the 2 hex-headuntil
until itit covers
screws into thethe
covers the door
door
bottom of the door.
surface
surface completely.
completely.
3.
3. Install
Install thethe 22 hex-head
hex-head screwsscrews into
into the
the bottom
bottom of of the
the door.
door.
2-10 n 9
INSTALLATION
ation 3. Install the white decorative screws on the opposite side of the 5. Push up on the top rear of the ice maker and locate the
door. leveling legs that are on the bottom rear of the ice maker.
6. Follow the instructions in Step 4 to change the height of the
WARNING
legs.
7. Use the level to recheck the ice maker to see that it is even
from front to back and side to side. If the ice maker is not
level, repeat steps 2 to 5. If the ice maker is level, go to the
Connect Water Supply section.
Cleaning
Electrical Shock Hazard Interior Components
Plug into a grounded 3 prong outlet.
1. Unplug ice maker or disconnect power.
Do not remove ground prong. 2. Open the storage bin door and remove any ice that is in the
Do not use an adapter. bin.
3. Remove the drain cap from the water pan and drain
Do not use an extension cord.
thoroughly. Replace the drain cap securely on the water pan.
Failure to follow these instructions can result in death, If the drain cap is loose, water will empty from the water pan,
fire, or electrical shock. and you will have either thin ice or no ice.
4. Pull out on the bottom of the cutter grid cover until the snaps
release to remove.
4. Plug into a grounded 3 prong outlet.
RECOMMENDED SOLUTIONS NOTE: On some models, remove the screw from the cutter
grid cover.
e Leveling
Check that it is plugged into a grounded 3 prong outlet. 5. Unplug the wiring harness from the left side of the cutter grid.
It is important for the ice maker
Check that the control is turned on. to be level in order to work
properly. Depending upon where you install the ice maker, you
maythe
Replace need
fusetoormake
resetseveral adjustments
the circuit breaker. to level it. You may also
use the leveling legs to lower the height of the ice maker for A
NOTE: If problems continue,
undercounter installations. contact an electrician.
RoomTools Needed
temperature must be above 55F (13C). Otherwise, bin thermostat may sense cold room temperature
and shut off even
Gather though the
the required binand
tools is not fullbefore
parts of ice. starting
The ice maker may not restart once it does shut off.
installation.
B
was
If there 9" level
a large amount of water added to the ice maker, wait a few minutes for the drain pump to clear. If
Adjustable
thereis still wrench
water in the bin, check to see whether the drain hose is kinked. A. Cutter grid cover
NOTE: It is easier to adjust the leveling legs if you have another B. Screw (on some models)
For models with drain pumps, check that the drain hose is not damaged, or kinked or pinched between cabinet
person to assist you.
and ice maker. Use only Whirlpool approved drain pump kit, Part Number 1901A.
1. Move the ice maker to its final location.
Water overflowing
NOTE: If the
thisreservoir is normal.
is a built-in This move
installation, overflowthehelps to purge
ice maker as minerals that were removed from the
water during
closethe
asice makingtoprocess.
possible the final location.
2. isPlace
If there the level on
a whooshing top of
sound, the product
check to see
the following whether the ice
things:
maker is level from front to back and side to side.
Make sure that the water supply is hooked up and turned on.
3. Push up on the top front of the ice maker, and then locate the
Makeleveling
sure that the drain
screws thatcap
areisontight
the and
bottomthe water drain
front of the pan pump is securely attached to the water pan.
ice maker.
4. isUsing
If there an adjustable
ice between wrench,plate
the evaporator change
andthetheheight
cuttingofgrid,
the check
legs asthat the ice maker is level. If the ice
A
maker is follows:
level, and the problem persists, run a cleaning cycle.
Turn the leveling leg to the right to lower that side of the
If the ice maker
iceismaker.
connected to a water supply pressure in excess of 60 psi, you may hear a loud sound during
water filling
associated with theleg
Turn the leveling flow
to of
thewater
left tothrough the side
raise that inlet of
valve. Call a licensed, qualified plumber to
the ice
determine themaker.
best method to reduce the supply water pressure (50 psi is recommended).
NOTE: The ice maker should not wobble. Use shims to add
stability when needed. A. Cutter grid cover
n 2-11
INSTALLATION
6. Unplug the ice level sensor from the right side of the cutter On Some Models
grid. Pull the ice level sensor down and forward away from After removing the ice scoop, remove the holder by
the cutter grid. removing the 2 screws.
7. Remove the right-hand and left-hand screws. Lift the cutter NOTE: On some models, remove the holder by lifting up
grid up and out. on the ice scoop holder and then out.
NOTE: Make sure the plastic spacer from the right-hand side Wash the ice scoop holder along with the other interior
of the cutter grid bracket stays with the cutter grid. components using the following instructions.
Replace the ice scoop holder by replacing the screws or
on some models, pushing in on the holder and then
down.
D
A
B E
C
F A
8. Remove the mounting screw that holds the water pan in 11. Wash the interior components (cutter grid, exterior of hoses,
place. Pull out on the front of the water pan. and water pan) and the storage bin, door gasket, ice scoop,
and ice scoop holder with mild soap or detergent and warm
9. Disconnect the pump bracket from the water pan and unplug water. Rinse in clean water. Then clean the same parts with a
the water pan drain pump. solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L)
warm water. Rinse again thoroughly in clean water.
NOTE: Do not remove hoses. Do not wash plastic parts in
dishwasher. They cannot withstand temperatures above
145F (63C).
12. To replace the water pan, set the water pan inside the ice bin.
Hook up the water pan pump. Snap the pump bracket back
A onto the water pan and place back into position. Secure the
B water pan by replacing the mounting screw.
C D
13. Check the following:
A. Water pan C. Drain cap Drain cap from the water pan is securely in place. If the
B. Water pan screw D. Drain pump cover drain cap is loose, water will empty from the water pan,
and you will have either thin ice or no ice.
10. Remove, clean and replace the ice scoop holder and ice Hose from water pan is inserted into storage bin drain
scoop. opening.
NOTE: On some models, the ice scoop holder is located in 14. Slide the cutter grid back into place and secure it by
the upper left of the unit, and on other models, the ice scoop replacing the right-hand screw and plastic spacer. Then
holder is located in the lower left of the unit. tighten the left-hand screw. Reconnect the cutter grid
harness and the ice level sensor harness.
On Some Models
15. Replace the cutter grid cover.
Remove the holder by removing the 2 screws.
NOTE: On some models, replace the cutter grid cover using
Wash the ice scoop holder and ice scoop along with the
the screw removed earlier.
other interior components using the following
instructions. 16. Gently wipe the control panel with a soft, clean dishcloth
Replace the ice scoop holder by replacing the screws. using warm water and a mild liquid dish detergent.
17. Plug in ice maker or reconnect power.
18. After cleaning, make sure that all controls are set properly
and that no control indicators are flashing.
A
A. Screw
B. Ice scoop holder
2-12 n
Controls and Operating Instructions
Section 3:
Controls and Operating
Instructions
This section provides operational use and care information for
Design 15 and 18 Ice Makers.
Normal Sounds
Cleaning
Accessories
Problem Solver
Ice Production
Ice Quality
Plumbing Problems
Warranty
n 3-1
Controls and Operating Instructions
User Guide
Ice Maker
LEARN MORE
In an effort to conserve natural resources, this ice maker includes a condensed User Guide. A complete Use and Care
Guide can be downloaded at www.jennair.com/manuals.
The model number is located on the inside of the ice maker.
Register your ice maker at www.jennair.com.
Para una version de estas instrucciones en espaol, visite www.jennair.com.
You can be killed or seriously injured if you dont immediately follow instructions.
DANGER
You can be killed or seriously injured if you dont follow instructions.
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
NOTES:
Pressing the On/Off button does not shut off power to the ice
maker.
Allow 24 hours to produce the first batch of ice. Discard the first 2
batches produced.
n 3-3
Controls and Operating Instructions
5. Turn the filter clockwise until it locks into the housing. Ensure that 2. Turn the water filter counterclockwise (to the left), and pull it
the alignment arrow on the filter head aligns with the locked straight out of the compartment.
symbol on the control box housing. NOTE: There may be some water in the filter. Some spilling may
NOTE: If the filter is not correctly locked into the housing, the ice occur.
maker will not produce ice. 3. Install the replacement water filter by following steps 2 through 5 in
the Install the Water Filter section.
Normal Sounds
A
Your new ice maker may make sounds that are not familiar to you.
Because the sounds are new to you, you might be concerned about
them. Most of the new sounds are normal. Hard surfaces such as
A. Alignment arrow aligned with locked symbol floors, walls and cabinets can make the sounds seem louder than they
actually are. The following describes the kinds of sounds that might be
6. Push the control box door closed until the latch snaps closed. new to you and what may be making them.
You will hear a buzzing sound when the water valve opens to fill the
The Water Filter Status Light water pan for each cycle.
The water filter status lights will help you know when to change your Rattling noises may come from the flow of the refrigerant or the
water filter. water line. Items stored on top of the ice maker can also make
The Order Filter status light will be illuminated when it is time to noises.
order a replacement filter. The high-efficiency compressor may make a pulsating or high
The Replace Filter status light will be illuminated when it is time to pitched sound.
replace the filter. Water running over the evaporator plate may make a splashing
Replacing the disposable water filter with a new filter will sound.
automatically reset the filter status tracking feature. See Using the Water running from the evaporator plate to the water pan may make
Controls. a splashing sound.
NOTES: As each cycle ends, you may hear a gurgling sound due to the
Replace Filter will remain illuminated if a filter is not installed. refrigerant flowing in your ice maker.
The Filter status light will flash if the filter is not correctly You may hear air being forced over the condenser by the condenser
installed or there is an obstruction in the water line. fan.
During the harvest cycle, you may hear a thud when the ice sheet
Replace the Water Filter slides from the evaporator onto the cutter grid.
To purchase a replacement water filter, see Accessories.
When you first start the ice maker, you may hear water running
Replace the disposable water filter when indicated on the water filter continuously. The ice maker is programmed to run a rinse cycle
status display or at least every 9 months. If the ice making rate before it begins to make ice.
decreases before the Replace Filter light illuminates, then replace the
filter. If the ice maker is connected to a water supply pressure in excess
of 60 psi, you may hear a loud sound during water filling associated
1. Locate the water filter compartment in the right-hand side of the with the flow of water through the inlet valve. Call a licensed,
control housing. See Step 3 in the Install Water Filter section. qualified plumber to determine the best method to reduce the
supply water pressure (50 psi is recommended).
A
B
Electrical Shock Hazard
Disconnect power before cleaning.
Replace all parts and panels before operating.
A. Water pan
B. Drain cap Failure to do so can result in death or electrical shock.
7. Press the CLEAN button. See Using the Controls. The light will
blink, indicating that the cleaning cycle is in process. When the 1. Unplug ice maker or disconnect power.
Cleaning Complete light is illuminated (approximately 2. Remove the 2 screws in the lower access panel and the 2 screws
70 minutes), the cleaning cycle is complete. During the cleaning from the base grille area of the front panel support.
cycle, the system will both clean and rinse itself. 3. Pull the bottom forward and then pull down to remove the lower
8. After the cleaning cycle is complete, remove the drain cap from the access panel.
water pan. Look for any cleaning solution left in the water pan. If
cleaning solution drains from the water pan, you should run the
clean cycle again. Be sure to refill the water pan with cleaner
before starting the clean cycle again. Be sure to replace the drain
cap securely on the water pan. If the drain cap is loose, water will
empty from the water pan and you will have either thin ice or no
ice.
NOTE: Severe scale buildup may require repeated cleaning with a
fresh quantity of cleaning solution.
4. Remove dirt and lint from the condenser fins and the unit
9. Press the ON/OFF button to resume ice production. compartment with a brush attachment on a vacuum cleaner.
Condenser
A Dirty or Clogged Condenser
Obstructs proper airflow. A
Reduces ice making capacity.
Causes higher than recommended operating temperatures which
may lead to component failure.
A. Condenser fins
Accessories
To order accessories, in the U.S.A., visit our website www.jennair.com/accessories or call 1-800-901-2042.
In Canada, visit our website www.whirlpoolparts.ca or call 1-800-807-6777.
Water Filter affresh* Stainless Steel Wipes
Order Part Number F2WC9I1 or ICE2 In U.S.A., order Part Number W10355049
Cleaner In Canada, order Part Number W10355049B
n 3-5
Controls and Operating Instructions
Problem Solver
Scan the code at left with your mobile device, or visit https://jennair.custhelp.com for
recommendations that may help you avoid a service call.
WARNING
Make sure that the drain cap is tight and the water drain pan pump is securely attached to the water pan.
If there is ice between the evaporator plate and the cutting grid, check that the ice maker is level. If the ice
maker is level, and the problem persists, run a cleaning cycle.
If the ice maker is connected to a water supply pressure in excess of 60 psi, you may hear a loud sound during
water filling associated with the flow of water through the inlet valve. Call a licensed, qualified plumber to
determine the best method to reduce the supply water pressure (50 psi is recommended).
3-6 n
Controls and Operating Instructions
Ice Production
WARNING
Ice Quality
n 3-7
Controls and Operating Instructions
Plumbing Problems
WARNING
Excessive Weight Hazard
Use two or more people to move and install ice maker.
Failure to do so can result in back or other injury.
This system has been tested according to NSF/ANSI Standards 42 for the reduction of the substances listed below. The concentration of the
indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the
system, as specified in NSF/ANSI Standards 42.
Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %
Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction
Chlorine Taste/Odor 50% reduction 1.9727 mg/L 2.0 mg/L 10% 0.71 mg/L 0.7788 mg/L 70.2 72.81
Test Parameters: pH = 7.5 0.5 unless otherwise noted. Flow = 0.50 gpm (1.89 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68F to 71.6F (20C to 22C). Rated service capacity = 2000 gallons (7571 liters).
It is essential that operational, maintenance, and filter replacement Refer to the Warranty section for the Manufacturers limited
requirements be carried out for the product to perform as advertised. warranty.
Use replacement filter P6RFWG2K, P6RFGEG2K, P6RFKG2K, Part
Number ICE2. Application Guidelines/Water Supply Parameters
Style 1 When the water filter status display changes from GOOD Water Supply City or Well
to ORDER, order a new filter. When the filter indicator reads Water Pressure 30 - 120 psi (207 - 827 kPa)
REPLACE, it is recommended that you replace the filter.
Water Temperature 33 - 100F (0.6 - 37.8C)
Style 2 Press FILTER to check the status of your water filter. If the
filter indicator light is yellow and the words ORDER FILTER appear Service Flow Rate 0.50 gpm (1.89 Lpm) @ 60 psi
on the display screen, order a new filter. If the filter indicator light is
red, it is recommended that you replace the filter.
These contaminants are not necessarily in your water supply. While
testing was performed under standard laboratory conditions, actual
performance may vary.
The product is for cold water use only.
Do not use with water that is microbiologically unsafe or of unknown
quality without adequate disinfection before or after the system.
Refer to the Warranty section for the Manufacturers name, address
and telephone number.
NSF is a registered trademark of NSF International.
3-8 n
Controls and Operating Instructions
Warranty
Warranty JENN-AIR ICE MAKER WARRANTY
THREE YEAR LIMITED
JENN-AIR ICEWARRANTY MAKER(PARTS WARRANTY AND LABOR)
For three years from the date of purchase, when this major appliance is installed, operated and maintained according to instructions attached to or
furnished with the product, Jenn-Air brand THREE of Whirlpool
YEAR Corporation
LIMITED WARRANTY or Whirlpool Canada (PARTSLP AND(hereafter
LABOR) Jenn-Air) will pay for factory specified
replacement
For three years partsfrom and
therepair
date labor to correct
of purchase, defects
when in materials
this major appliance or workmanship that existed
is installed, operated andwhen this major
maintained appliance
according was purchased.
to instructions attached to or
furnished with the product, Jenn-Air brand ofFOURTH WhirlpoolTHROUGH
Corporation FIFTH YEAR LIMITED
or Whirlpool Canada LP WARRANTY
(hereafter Jenn-Air) will pay for factory specified
replacement parts and repair labor (SEALED
to correct REFRIGERATION
defects in materials SYSTEM PARTS ONLY
or workmanship - LABOR
that existed whenNOT INCLUDED)
this major appliance was purchased.
In the fourth through the fifth years from the FOURTH date of original
THROUGH purchase, FIFTH whenYEAR this LIMITED
major applianceWARRANTY is installed, operated and maintained according to
instructions attached to or furnished (SEALEDwith the product, Jenn-AirSYSTEM
REFRIGERATION will pay for PARTSfactory specified
ONLY - LABOR replacement parts for the following components to
NOT INCLUDED)
correct non-cosmetic
In the fourth through the defects in materials
fifth years from the or date
workmanship
of originalinpurchase,
the sealed refrigeration
when this major system
appliancethat existed when
is installed, this major
operated andappliance
maintained wasaccording
purchased:to
compressor, evaporator,
instructions attached condenser,
to or furnished dryer/strainer,
with the product, andJenn-Air
connecting will tubing.
pay for This limited
factory 5-yearreplacement
specified warranty is only partsfor forthe
thesealed refrigeration
following components system
to
replacement parts as identified and does not include labor.
correct non-cosmetic defects in materials or workmanship in the sealed refrigeration system that existed when this major appliance was purchased:
YOUR SOLE evaporator,
compressor, AND EXCLUSIVE condenser,REMEDY UNDER THE
dryer/strainer, andLIMITED
connecting WARRANTY
tubing. This SHALL BE 5-year
limited PRODUCT REPAIR
warranty AS for
is only PROVIDED
the sealed HEREIN. Service
refrigeration must be
system
provided by aparts
replacement Jenn-Air designated
as identified andservice
does not company. This limited warranty is valid only in the United States or Canada and applies only when the
include labor.
major appliance
YOUR SOLE AND is EXCLUSIVE
used in the country
REMEDY in UNDER
which it THEwas LIMITED
purchased. This limited
WARRANTY warranty
SHALL is effective REPAIR
BE PRODUCT from theAS date of the original
PROVIDED consumer
HEREIN. purchase.
Service must be
Proof
provided of original purchase
by a Jenn-Air date is required
designated service to obtain service
company. underwarranty
This limited this limited warranty.
is valid only in the United States or Canada and applies only when the
major appliance is used in the country in which it wasITEMS purchased.EXCLUDEDThis limitedFROM warranty
WARRANTYis effective from the date of the original consumer purchase.
Proof of original purchase date is required to obtain service under this limited warranty.
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance ITEMS EXCLUDED
is used for other FROM thanWARRANTY
normal, single-family household use or when it is used in a
Thismanner
limitedthatwarranty does not
is inconsistent to cover:
published user or operator instructions and/or installation instructions.
2. Replacement
1. Service calls to correct
parts the installation
or repair labor if thisofmajor
your major
applianceappliance,
is usedtofor instruct
other thanyou on how to
normal, use your major
single-family appliance,
household use orto when
replace or used
it is repairinhouse
a
fuses,
mannerorthat to correct house wiring
is inconsistent or plumbing.
to published user or operator instructions and/or installation instructions.
3.
2. Service
Service calls
calls toto repair
correctorthe replace appliance
installation light
of your bulbs,
major air filters to
appliance, or instruct
water filters.
you on Consumable
how to useparts are excluded
your major appliance, fromtowarranty
replace or coverage.
repair house
4. Damage
fuses, or resulting
to correctfrom house accident,
wiring or alteration,
plumbing. misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with
3. electrical
Service callsor plumbing
to repair or codes,
replaceor use of products
appliance not approved
light bulbs, air filtersbyorJenn-Air.
water filters. Consumable parts are excluded from warranty coverage.
5.
4. Cosmetic damage,from
Damage resulting including
accident,scratches, dents,
alteration, chipsabuse,
misuse, or other damage
fire, to the
flood, acts offinish
God, of your major
improper appliance,
installation, unless such
installation damage
not in resultswith
accordance from
defects
electricalinor materials
plumbing orcodes,
workmanship
or use of and is reported
products to Jenn-Air
not approved bywithin 30 days from the date of purchase.
Jenn-Air.
6.
5. Any food or
Cosmetic medicine
damage, loss due
including to refrigerator
scratches, dents, orchips
freezer or product
other damage failures. to the finish of your major appliance, unless such damage results from
7. Pickup
defects and delivery. or
in materials This major appliance
workmanship and isisreported
intendedtotoJenn-Air
be repaired withinin your
30 days home.from the date of purchase.
8.
6. Repairs
Any foodtoorparts or systems
medicine loss due resulting from unauthorized
to refrigerator modifications
or freezer product failures.made to the appliance.
9.
7. Expenses
Pickup andfor travel and
delivery. Thistransportation
major appliance for is
product
intended service
to beifrepaired
your major appliance
in your home.is located in a remote area where service by an authorized
8. Jenn-Air
Repairs to servicer
parts orissystems
not available.resulting from unauthorized modifications made to the appliance.
10.
9. The removal
Expenses forand reinstallation
travel of your major
and transportation appliance
for product if it is
service installed
if your major in appliance
an inaccessible location
is located in a or is notarea
remote installed
where in service
accordance
by anwith Jenn-Air's
authorized
publishedservicer
Jenn-Air installation
is not instructions.
available.
11.
10. Replacement
The removal and parts or repair labor
reinstallation on major
of your majorappliances
appliance ifwith it is original
installedmodel/serial
in an inaccessible numbers that have
location or isbeen removed,
not installed in altered or cannot
accordance be easily
with Jenn-Air's
determined.
published installation instructions.
12. Replacement
11. Discoloration,parts rust ororoxidation
repair labor of stainless
on major steel surfaces.
appliances with original model/serial numbers that have been removed, altered or cannot be easily
Thedetermined.
cost of repair or replacement under these excluded circumstances shall be borne by the customer.
12. Discoloration, rust or oxidation of stainless steel surfaces.
DISCLAIMER OF IMPLIED WARRANTIES
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST
DISCLAIMER OF IMPLIED PERIOD ALLOWED BY LAW. Some states and provinces do not allow
WARRANTIES
limitations on the durationINCLUDING
IMPLIED WARRANTIES, of implied warranties
ANY IMPLIED of merchantability
WARRANTY OF or fitness, so this limitation
MERCHANTABILITY OR mayIMPLIEDnot apply to you. This
WARRANTY warranty FOR
OF FITNESS givesAyou specific
legal rights, and
PARTICULAR you also may
PURPOSE, ARE have
LIMITED otherTO rights
ONEthatYEAR varyOR fromTHE state to state or
SHORTEST province
PERIOD to province.
ALLOWED BY LAW. Some states and provinces do not allow
limitations on the duration of implied warranties DISCLAIMER of merchantability
OF REPRESENTATIONSor fitness, so this limitationOF
OUTSIDE may not apply to you. This warranty gives you specific
WARRANTY
legal rights, and you also may have other rights that vary from state to state or province to province.
Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations
contained in this Warranty. If you want aDISCLAIMER longer or moreOF comprehensive
REPRESENTATIONS warranty than OUTSIDE the limited warranty that comes with this major appliance, you
OF WARRANTY
should ask
Jenn-Air Jenn-Air
makes or your retailer about
no representations about thebuying an extended
quality, durability,warranty.
or need for service or repair of this major appliance other than the representations
contained in this Warranty. If you wantOF
LIMITATION a longer
REMEDIES;or moreEXCLUSION
comprehensive OFwarranty
INCIDENTAL than the AND limited warranty that comes
CONSEQUENTIAL DAMAGESwith this major appliance, you
should ask Jenn-Air or your retailer about buying an extended warranty.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. JENN-AIR
SHALL NOT BE LIABLELIMITATION FOR INCIDENTAL OR CONSEQUENTIAL
OF REMEDIES; EXCLUSION DAMAGES.
OF INCIDENTAL Some states ANDand provinces do not DAMAGES
CONSEQUENTIAL allow the exclusion or limitation of
incidental
YOUR SOLE or consequential
AND EXCLUSIVE damages,
REMEDY so these
UNDER limitations and exclusions
THIS LIMITED WARRANTY maySHALLnot apply BEto you. This warranty
PRODUCT REPAIR AS gives you specific
PROVIDED legal rights,
HEREIN. and you
JENN-AIR
also
SHALL may have
NOT BEother
LIABLErightsFOR that vary from state
INCIDENTAL to state or provinceDAMAGES.
OR CONSEQUENTIAL to province.Some states and provinces do not allow the exclusion or limitation of
incidental
If outside the or consequential
50 United States damages, so these
and Canada, limitations
contact your and exclusions
authorized may not
Jenn-Air dealerapply to you. Thisif warranty
to determine gives youapplies.
another warranty specific legal rights, and you 1/11
also may have other rights that vary from state to state or province to province.
For additional product information, in the U.S.A., visit www.jennair.com. In Canada, visit www.jennair.ca.
If outside the 50 United States and Canada, contact your authorized Jenn-Air dealer to determine if another warranty applies. 1/11
If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may contact Jenn-Air
at the number below.
For additional product information, in the U.S.A., visit www.jennair.com. In Canada, visit www.jennair.ca.
Have
If you your
do notcomplete
have access modeltonumber ready.
the Internet andYouyoucan findassistance
need your modelusing number yourand serial or
product number
you wouldon the likelabel, located service,
to schedule on the inside wallcontact
you may of the ice maker.
Jenn-Air
Forthe
at assistance or service, call 1-800-JENN-AIR (536-6247). If you need further assistance, you can write to Jenn-Air with any questions or concerns
number below.
at theyour
Have address below:
complete model number ready. You can find your model number and serial number on the label, located on the inside wall of the ice maker.
In the
For U.S.A.: or service, call 1-800-JENN-AIR (536-6247). If you need further
assistance In assistance,
Canada: you can write to Jenn-Air with any questions or concerns
at theJenn-Air
address Brand
below:Home Appliances Jenn-Air Brand Home Appliances
In theCustomer
U.S.A.: eXperience Center Customer eXperience Centre
In Canada:
553 Benson
Jenn-Air Brand RoadHome Appliances 200 6750
Jenn-Air BrandCentury
Home Ave.
Appliances
Benton
Customer Harbor, MI 49022-2692
eXperience Center Mississauga,
Customer eXperience Ontario L5N Centre0B7
Please include
553 Benson Road a daytime phone number in your correspondence. 200 6750 Century Ave.
Please keepHarbor,
Benton all provided instructions and your model number information for future
MI 49022-2692 reference.Ontario L5N 0B7
Mississauga,
Please include a daytime phone number in your correspondence.
Please keep all provided instructions and your model number information for future reference.
8/13
W10541616B
/ 2013 Jenn-Air. Used under license in Canada. All rights reserved. Printed in U.S.A.
W10541616B
/ 2013 Jenn-Air. Used under license in Canada. All rights reserved. n 3-9
Printed
8/13
in U.S.A.
Controls and Operating Instructions
5SER'UIDE
)CE-AKER
,%!2.-/2%
In an effort to conserve natural resources, this ice maker includes a condensed User Guide. A complete Use and Care
Guide can be downloaded at www.kitchenaid.com/manuals. The model number is located on the inside of the ice maker.
In the U.S.A., register your ice maker at www.kitchenaid.com.
In Canada, register your ice maker at www.kitchenaid.ca.
Para una version de estas instrucciones en espaol, visite www.kitchenaid.com.
You can be killed or seriously injured if you dont immediately follow instructions.
DANGER
You can be killed or seriously injured if you dont follow instructions.
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
/0%2!4).'9/52)#%-!+%2
(OW9OUR)CE-AKER7ORKS
When you first start your ice maker, the water pan will fill and the 4HE)CE-AKING0ROCESS
system will rinse itself before starting to make ice. The rinsing process 1. Water is constantly circulated over a
takes about 5 minutes. freezing plate. As the water freezes into
Under normal operating conditions, the ice maker will cycle at preset ice, the minerals in the water are
temperatures. The ice level sensor located in the ice storage bin will rejected. This produces a sheet of ice
monitor the ice levels. with a low mineral content.
IMPORTANT: If the water supply to the ice maker is turned off, be sure
to set the ice maker control to OFF.
3-10 n 1 W10541605B
Controls and Operating Instructions
2. When the desired thickness is reached,
the ice sheet is released and slides onto
7ATER&ILTRATION3YSTEM
a cutter grid. The grid divides the sheet
into individual cubes. Do not use with water that is microbiologically unsafe or
3. The water containing the rejected of unknown quality without adequate disinfection before
minerals is drained after each freezing or after the system. Systems certified for cyst reduction
cycle. may be used on disinfected waters that may contain
4. Fresh water enters the machine for the next ice making cycle. filterable cysts.
5. Cubes fall into the storage bin. When the
bin is full, the ice maker shuts off )NSTALLTHE7ATER&ILTER
automatically and restarts when more ice is
1. Locate the accessory packet in the ice maker and remove the
needed. The ice bin is not refrigerated, and
water filter.
some melting will occur. The amount of
melting varies with room temperature. 2. Take the water filter out of its packaging and remove the cover from
the O-rings. Be sure the O-rings are still in place after the cover is
NOTE: As the room and water temperatures
removed.
vary, so will the amount of ice produced and
stored. This means that higher operating temperatures result in
reduced ice production.
5SINGTHE#ONTROLS
1. To start ice production, press ON/OFF.
2. To stop ice maker operation, press ON/OFF. A B C D
NOTES:
Pressing the On/Off button does not shut off power to the ice
maker.
Allow 24 hours to produce the first batch of ice. Discard the first 2
batches produced.
-AX)CE-ODE
Select the Max Ice feature when you have an upcoming need for a
large amount of ice and the ice bin is low or empty. Max Ice mode will A
produce a greater quantity of ice in a 24-hour period.
A. Door
Press MAX ICE while the ice maker is on. The indicator light will
illuminate. 4. Using the arrow pointing to the alignment pin on the side of the
Press MAX ICE again to turn off the Max Ice feature. The indicator filter and the arrow inside the control housing, align the alignment
light will turn off. pin with the cutout notch and insert the filter into the housing.
The Max Ice mode will be on when you first turn on the product. It A B
will turn off after 24 hours. To turn Max Ice back on, press MAX ICE.
C
#LEAN D
It is recommended that you clean the ice maker when the Cleaning
Needed light is illuminated or 9 months has elapsed or ice production
decreases significantly. To clean your ice maker, see Ice Maker
System in the Cleaning section.
F
$OOR!JAR!LARM
The Door Ajar Alarm feature sounds an alarm when the ice maker door
is open for 5 minutes. The alarm will repeat every 2 minutes. Close the
door to turn off. The feature then resets and will reactivate when the E
door is left open again for 5 minutes.
A. Alignment pin D. Cutout notch inside control housing
B. Unlocked symbol E. Arrow pointing to cutout notch
C. Locked symbol F. Arrow pointing to alignment pin
n 3-11
2
Controls and Operating Instructions
5. Turn the filter clockwise until it locks into the housing. Ensure that NOTE: There may be some water in the filter. Some spilling may
5. the
Turnalignment
the filter clockwise
arrow on the untilfilter
it locks
headinto the housing.
aligns Ensure that
with the locked NOTE:
occur. There may be some water in the filter. Some spilling may
the alignment
symbol on the arrow
controlonbox
thehousing.
filter head aligns with the locked occur.
symbol on the control box housing. 3. Install the replacement water filter by following steps 2 through 5 in
NOTE: If the filter is not correctly locked into the housing, the ice 3. Install the replacement
the Install watersection.
the Water Filter filter by following steps 2 through 5 in
NOTE:will
maker If the
notfilter is notice.
produce correctly locked into the housing, the ice the Install the Water Filter section.
maker will not produce ice.
.ORMAL3OUNDS
.ORMAL3OUNDS
Your new ice maker may make sounds that are not familiar to you.
A Your new the
Because ice sounds
maker may maketosounds
are new you, you that are not
might familiar to you.
be concerned about
A Because theofsounds
them. Most the neware new toare
sounds you, you might
normal. Hardbe concerned
surfaces suchabout
as
them.
floors, Most
wallsof thecabinets
and new sounds are normal.
can make the soundsHardseem
surfaces
louder such as they
than
floors,
actuallywalls
are. and
The cabinets
followingcan make the
describes thesounds
kinds ofseemsoundslouderthat than
mightthey
be
A. Alignment arrow aligned with locked symbol actually
new to youare.and
Thewhat
following
may be describes
making the them.kinds of sounds that might be
A. Alignment arrow aligned with locked symbol new to you and what may be making them.
You will hear a buzzing sound when the water valve opens to fill the
6. For 15" (38.1 cm) models, push the control box door closed until You will hear
6. the
For latch
15" (38.1 cm)
snaps models, push the control box door closed until
closed.
water pan foraeach
buzzingcycle.sound when the water valve opens to fill the
the latch snaps closed. water pan for each cycle.
Rattling noises may come from the flow of the refrigerant or the
4HE7ATER&ILTER3TATUS,IGHT Rattling
water noises
line. Itemsmaystoredcome onfrom
top of the
theflow
iceof the refrigerant
maker can also make or the
4HE7ATER&ILTER3TATUS,IGHT
The water filter status lights will help you know when to change your
water line. Items stored on top of the ice maker can also make
noises.
The water noises.
water filter.filter status lights will help you know when to change your The high-efficiency compressor may make a pulsating or high
water filter. The high-efficiency
pitched sound. compressor may make a pulsating or high
The Order Filter status light will be illuminated when it is time to
The
orderOrder Filter status
a replacement filter.light will be illuminated when it is time to pitched sound.
Water running over the evaporator plate may make a splashing
order a replacement filter. Water running over the evaporator plate may make a splashing
sound.
The Replace Filter status light will be illuminated when it is time to
The Replace
replace Filter status light will be illuminated when it is time to
the filter. sound.
Water running from the evaporator plate to the water pan may make
replace the filter. Water running from the evaporator plate to the water pan may make
Replacing the disposable water filter with a new filter will a splashing sound.
Replacing thereset
automatically disposable
the filter water filter
status with a feature.
tracking new filterSeewillUsing the a splashing sound.
As each cycle ends, you may hear a gurgling sound due to the
automatically reset the filter status tracking feature. See Using the As each cycle ends,
Controls. refrigerant flowing in you
yourmay hear a gurgling sound due to the
ice maker.
Controls. refrigerant flowing in your ice maker.
NOTES: You may hear air being forced over the condenser by the condenser
NOTES: You
Replace Filter will remain illuminated if a filter is not installed. fan. may hear air being forced over the condenser by the condenser
Replace Filter will remain illuminated if a filter is not installed. fan.
The Filter status light will flash if the filter is not correctly During the harvest cycle, you may hear a thud when the ice sheet
The Filter
installed statusislight
or there will flash if in
an obstruction thethe
filter is not
water correctly
line. Duringfrom
slides the harvest cycle, you
the evaporator onto maythehear
cuttera thud
grid. when the ice sheet
installed or there is an obstruction in the water line. slides from the evaporator onto the cutter grid.
When you first start the ice maker, you may hear water running
2EPLACETHE7ATER&ILTER When you firstThe start
2EPLACETHE7ATER&ILTER continuously. icethe ice maker,
maker you may hear
is programmed to runwater
a rinserunning
cycle
To purchase a replacement water filter, see Accessories. continuously. The ice
before it begins to make ice. maker is programmed to run a rinse cycle
To purchase a replacement water filter, see Accessories. before it begins to make ice.
Replace the disposable water filter when indicated on the water filter
Replace the disposable If the ice maker is connected to a water supply pressure in excess
status display or at leastwater
everyfilter when indicated
9 months. on the water
If the ice making rate filter If
status display or atthe
least every Filter
9 months. If the ice making rate ofthe ice maker
60 psi, you may is connected
hear a loudtosound a water supply
during pressure
water in excess
filling associated
decreases before Replace light illuminates, then replace the of 60the
psi,flow
youofmay hear a loud thesound
decreases before the Replace Filter light illuminates, then replace the with water through inletduring
valve.water
Call afilling associated
licensed,
filter. with the flow of water through the
filter. qualified plumber to determine theinlet
bestvalve.
method Calltoareduce
licensed, the
1. Locate the water filter compartment in the right-hand side of the qualified
supply plumber
water to determine
pressure (50 psi isthe best method to reduce the
recommended).
1. control
Locate housing.
the waterSee filterStep
compartment in the Water
3 in the Install right-hand
Filterside of the
section. supply water pressure (50 psi is recommended).
control housing. See Step 3 in the Install Water Filter section.
2. Turn the water filter counterclockwise (to the left), and pull it
2. Turn theout
straight water filter
of the counterclockwise (to the left), and pull it
compartment.
straight out of the compartment.
#!2).'&/29/52)#%-!+%2
#!2).'&/29/52)#%-!+%2
#LEANING
#LEANING
The ice making system and the air cooled condenser need to be NOTE: Use one 16 oz (473 mL) bottle of approved ice maker cleaner.
The ice making
cleaned system
regularly for theand
ice the air cooled
maker condenser
to operate at peak need to beand to
efficiency NOTE:
To order,Use
seeone 16 oz (473 mL) bottle of approved ice maker cleaner.
Accessories.
cleaned regularlyfailure
avoid premature for theofice makercomponents.
system to operate atSee
peak efficiency
the and to
Ice Maker To order, see Accessories.
avoid premature failure of system components. See the Ice Maker 1. Press the ON/OFF button.
System and the Condenser sections. 1. Press the ON/OFF button.
System and the Condenser sections. 2. Wait 5 to 10 minutes for the ice to fall into the storage bin. Remove
2. all
Waitice5 from
to 10the
minutes
storageforbin.
the ice to fall into the storage bin. Remove
%XTERIOR3URFACES all ice from the storage bin.
%XTERIOR3URFACES 3. Unscrew the drain cap from the bottom of the water pan located
Wash the exterior enamel surfaces and gaskets with warm water and 3. inside
Unscrew thethe drain bin
storage capas from the bottom
shown. of the
Allow the water
water pan located
to drain
Washsoap
mild the exterior enamel
or detergent. surfaces
Wipe and
and dry. gaskets
Regular with
use of awarm
goodwater and
household inside the storage bin as shown. Allow the water to drain
mild soap or detergent. Wipe and dry.maintain
Regularthe
usefinish.
of a good household completely.
appliance cleaner and wax will help Do not use completely.
appliance cleaner on
abrasive cleaners andenamel
wax willsurfaces
help maintain
as theythe finish.
may Do not
scratch the use
finish. 4. Replace the drain cap securely on the water pan. If the drain cap is
abrasive cleaners on enamel surfaces as they may scratch the finish. 4. loose,
Replace the drain
water cap securely
will empty from theon the water
water pan andpan. If the
you will drain
have cap is
either
For products with a stainless steel exterior, use a clean sponge or soft loose,
thin icewater
or nowill
ice.empty from the water pan and you will have either
For
clothproducts withdetergent
and a mild a stainless steel exterior,
in warm water. Douse
notause
clean spongeororharsh
abrasive soft thin ice or no ice.
cloth and a
cleaners. Domild
notdetergent in warm
use chlorine bleachwater. Dostainless
on the not use abrasive or harsh
steel surfaces. 5. Read and follow all handling information on the cleaner bottle
cleaners. Do not use chlorine bleach on the stainless steel surfaces. 5. before
Read and follow allthe
completing handling information
steps below. on the
Use one 16 cleaner
oz (473 bottle
mL) bottle
before
of completing
approved the steps
ice maker cleaner.below. Use one 16 oz (473 mL) bottle
)CE-AKER3YSTEM of approved ice maker cleaner.
)CE-AKER3YSTEM
Minerals that are removed from water during the freezing cycle will
Minerals
eventuallythat area removed
form hard scaly from waterinduring
deposit the freezing
the water cycle will the
system. Cleaning
eventually
system form ahelps
regularly hard scaly
removedeposit in the water
the mineral scale system.
buildup. Cleaning
How oftenthe
system
you regularly
need to cleanhelps removedepends
the system the mineral
uponscale
howbuildup.
hard your How often
water is.
you
Withneed
hard to clean
water of the system
15 to depends(4
20 grains/gal. upon
to 5how hard youryou
grains/liter), water
mayis.
With
need hard water
to clean theofsystem
15 to 20
asgrains/gal. (4 to 95 months.
often as every grains/liter), you may
need to clean the system as often as every 9 months.
3-12 n 3
3
Controls and Operating Instructions
6. Pour one bottle of solution into the water pan. Fill the bottle twice
with tap water and pour it into the water pan. WARNING
A
B
Electrical Shock Hazard
Disconnect power before cleaning.
Replace all parts and panels before operating.
A. Water pan
B. Drain cap Failure to do so can result in death or electrical shock.
7. Press the CLEAN button. See Using the Controls. The light will
blink, indicating that the cleaning cycle is in process. When the 1. Unplug ice maker or disconnect power.
Cleaning Complete light is illuminated (approximately 2. Remove the 2 screws in the lower access panel and the 2 screws
70 minutes), the cleaning cycle is complete. During the cleaning from the base grille area of the front panel support.
cycle, the system will both clean and rinse itself. 3. Pull the bottom forward and then pull down to remove the lower
8. After the cleaning cycle is complete, remove the drain cap from the access panel.
water pan. Look for any cleaning solution left in the water pan. If
cleaning solution drains from the water pan, you should run the CM MODELS CM MODELS
clean cycle again. Be sure to refill the water pan with cleaner
before starting the clean cycle again. Be sure to replace the drain A
cap securely on the water pan. If the drain cap is loose, water will A
empty from the water pan and you will have either thin ice or no
ice.
NOTE: Severe scale buildup may require repeated cleaning with a
fresh quantity of cleaning solution.
9. Press the ON/OFF button to resume ice production. B
B
#ONDENSER
A. Lower access panel screws
!$IRTYOR#LOGGED#ONDENSER B. Base grille screws
Obstructs proper airflow. 4. Remove dirt and lint from the condenser fins and the unit
Reduces ice making capacity. compartment with a brush attachment on a vacuum cleaner.
Causes higher than recommended operating temperatures which
may lead to component failure.
A. Condenser fins
!##%33/2)%3
To order accessories, in the U.S.A., visit our website www.kitchenaid.com/accessories or call 1-800-901-2042.
In Canada, visit our website www.whirlpoolparts.ca or call 1-800-807-6777.
7ATER&ILTER AFFRESH
3TAINLESS3TEEL7IPES
Order Part Number F2WC9I1 or ICE2 In U.S.A., order Part Number W10355049
#LEANER In Canada, order Part Number W10355049B
Order Part Number 4396808 AFFRESH
+ITCHEN!PPLIANCE#LEANER
AFFRESH
3TAINLESS3TEEL#LEANER In U.S.A., order Part Number W10355010
In U.S.A., order Part Number W10355016 In Canada, order Part Number W10355010B
In Canada, order Part Number W10355016B
n 3-13
4
Controls and Operating Instructions
02/",%-3/,6%2
Scan the code at left with your mobile device, or visit https://kitchenaid.custhelp.com for recommendations that
may help you avoid a service call.
)CE-AKER/PERATION
WARNING
02/",%- 2%#/--%.$%$3/,54)/.3
Ice Maker Will Not Operate Check that it is plugged into a grounded 3 prong outlet.
Check that the control is turned on.
Replace the fuse or reset the circuit breaker.
NOTE: If problems continue, contact an electrician.
Room temperature must be above 55F (13C). Otherwise, bin thermostat may sense cold room temperature
and shut off even though the bin is not full of ice. The ice maker may not restart once it does shut off.
If there was a large amount of water added to the ice maker, wait a few minutes for the drain pump to clear. If
there is still water in the bin, check to see whether the drain hose is kinked.
For models with drain pumps, check that the drain hose is not damaged, or kinked or pinched between cabinet
and ice maker. Use only Whirlpool approved drain pump kit, Part Number 1901A.
Ice Maker Seems Noisy Water overflowing the reservoir is normal. This overflow helps to purge minerals that were removed from the
water during the ice making process.
If there is a whooshing sound, check the following things:
Make sure that the water supply is hooked up and turned on.
Make sure that the drain cap is tight and the water drain pan pump is securely attached to the water pan.
If there is ice between the evaporator plate and the cutting grid, check that the ice maker is level. If the ice
maker is level, and the problem persists, run a cleaning cycle.
If the ice maker is connected to a water supply pressure in excess of 60 psi, you may hear a loud sound during
water filling associated with the flow of water through the inlet valve. Call a licensed, qualified plumber to
determine the best method to reduce the supply water pressure (50 psi is recommended).
3-14 n 5
Controls and Operating Instructions
)CE0RODUCTION
WARNING
02/",%- 2%#/--%.$%$3/,54)/.3
Ice Maker Runs But Produces Check that the control is turned on.
No Ice
Check that the water supply is properly connected and turned on.
If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten
the drain cap.
Clean the drain tube.
Check that there are no kinks in the drain line.
Ice Maker Runs But Produces If the accelerated ice production feature is turned on, this feature increases the ice production rate to provide
Very Little Ice you with more ice in the same amount of time.
Room temperatures of more than 90F (32C) will normally reduce ice production.
Dirt or lint may be blocking the airflow through the condenser.
If there is white scale buildup in the ice makers water or freezing system, you should clean the ice maker.
If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten
the drain cap.
Ensure that the cutter grid is securely in place and that its harness plug is connected.
Check that water filter is properly installed.
)CE1UALITY
02/",%- 2%#/--%.$%$3/,54)/.3
Off Taste, Odor or Gray Color If there is unusually high mineral content in the water supply, the water may need to be treated.
in the Ice
If there is mineral scale buildup, clean your ice maker.
Do not store any foods in the ice bin.
Make sure that all packaging materials were removed at the time of installation.
Thin, Soft or Clumps of Ice If there is unusually high mineral content in the water supply, the water may need to be treated.
If there is mineral scale buildup, clean your ice maker.
If there are clumps of ice in the bin and if ice is not used regularly, it will melt and form clumps. Break the clumps
with the ice scoop provided.
n 3-15
6
WARNING
Controls and Operating Instructions
Excessive Weight Hazard
0LUMBING0ROBLEMS Use two or more people to move and install ice maker.
Failure to do so can result in back or other injury.
WARNING
02/",%- 2%#/--%.$%$3/,54)/.3
Excessive Weight Hazard
Water Not Entering Drain If the drain
Usehose
two is
ornot aligned
more overtothe
people drain,
move move
and the ice
install ice maker
maker.to align the drain.
Properly NOTE: Service
Failure technicians
to do so can cannot
resultrepair plumbing
in back problems
or other injury.outside of the ice maker. Call a licensed, qualified
plumber.
02/",%- 2%#/--%.$%$3/,54)/.3
Water Not Entering Drain 0%2&/2-!.#%$!4!3(%%4
If the drain hose is not aligned over the drain, move the ice maker to align the drain.
Properly NOTE: Service technicians cannot repair plumbing problems outside of the ice maker. Call a licensed, qualified
plumber. Ice Maker Water Filtration System
Model P6GEG2KL, P6KG2KL, P6WG2KL Capacity 2000 Gallons (7571 Liters)
0%2&/2-!.#%$!4!3(%%4
System tested and certified by NSF
International against NSF/ANSI
Standard 42 for the reduction of
Ice Maker Chlorine
WaterTaste
Filtration
and Odor. System
3-16 n
NSF is a registered trademark of NSF International. 7
Controls and Operating Instructions
7!22!.49
7!22!.49
KITCHENAID ICE MAKER WARRANTY
KITCHENAID
THREE YEAR LIMITED
ICE MAKER
WARRANTY WARRANTY
(PARTS AND LABOR)
For three years from the date of purchase, when this major appliance is installed, operated and maintained according to instructions attached to or
furnished with the product, KitchenAid brand THREE YEAR Corporation
of Whirlpool LIMITED WARRANTY or Whirlpool(PARTSCanada AND LABOR)KitchenAid) will pay for factory specified
LP (hereafter
replacement
For three years parts
from andtherepair
date labor to correct
of purchase, defects
when in materials
this major appliance or workmanship that existed
is installed, operated andwhen this major
maintained appliance
according was purchased.
to instructions attached to or
furnished with the product, KitchenAid brandFOURTH of Whirlpool Corporation
THROUGH FIFTH or Whirlpool
YEAR LIMITED Canada WARRANTY
LP (hereafter KitchenAid) will pay for factory specified
replacement parts and repair labor to correct
(SEALED defects in materials
REFRIGERATION SYSTEMor workmanship
PARTS ONLY that existed
- LABOR when NOTthisINCLUDED)
major appliance was purchased.
In the fourth through the fifth year from the date FOURTHof originalTHROUGH
purchase, FIFTH
whenYEAR LIMITED
this major applianceWARRANTY
is installed, operated and maintained according to
instructions attached to or furnished (SEALED with theREFRIGERATION
product, KitchenAid SYSTEMwill payPARTS ONLY
for factory - LABOR
specified NOT INCLUDED)
replacement parts for the following components to
correct
In non-cosmetic
the fourth through the defects in materials
fifth year from theor workmanship
date in the sealed
of original purchase, when refrigeration
this majorsystem
appliance thatisexisted when
installed, this major
operated and appliance
maintainedwas purchased:
according to
compressor,attached
instructions evaporator, to orcondenser,
furnished dryer/strainer,
with the product, andKitchenAid
connectingwill tubing.
pay for This limitedspecified
factory 5-year warranty
replacementis only for the
parts sealed
for the refrigeration
following componentssystemto
replacement parts as identified
correct non-cosmetic defects inand does not
materials include labor. in the sealed refrigeration system that existed when this major appliance was purchased:
or workmanship
compressor,
YOUR SOLE evaporator,
AND EXCLUSIVE condenser,REMEDY dryer/strainer,
UNDER THIS and LIMITED
connecting tubing. This
WARRANTY limited
SHALL BE5-year warranty
PRODUCT is only
REPAIR ASfor the sealedHEREIN.
PROVIDED refrigeration system
Service must be
replacement
provided by aparts as identified
KitchenAid and does
designated not company.
service include labor. This limited warranty is valid only in the United States or Canada and applies only when the
major
YOURappliance
SOLE AND is EXCLUSIVE
used in the countryREMEDY in which
UNDER it was
THISpurchased.
LIMITED WARRANTY This limited SHALLwarranty BEisPRODUCT
effective from the date
REPAIR of original consumer
AS PROVIDED purchase.
HEREIN. Service mustProof
be
of originalby
provided purchase date is
a KitchenAid required toservice
designated obtaincompany.
service under This this
limitedlimited warranty.
warranty is valid only in the United States or Canada and applies only when the
major appliance is used in the country in which it was purchased. This limited warranty is effective from the date of original consumer purchase. Proof
of original purchase date is required to obtain service ITEMS under this EXCLUDED
limited warranty.FROM WARRANTY
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance ITEMS EXCLUDED
is used for other FROM thanWARRANTY
normal, single-family household use or when it is used in a
Thismanner
limitedthatwarranty does nottocover:
is inconsistent published user or operator instructions and/or installation instructions.
1. Service
2. Replacement calls to parts or repair
correct labor if thisofmajor
the installation your majorappliance is usedtofor
appliance, other than
instruct you onnormal,
how to single-family
use your major household
appliance,use orto when
replaceit is
or used
repairinhouse
a
mannerorthat
fuses, is inconsistent
to correct house wiring to published user or operator instructions and/or installation instructions.
or plumbing.
2. Service calls to repair
3. correctorthe installation
replace of your
appliance light major
bulbs,appliance,
air filters to or instruct you on
water filters. how to useparts
Consumable your major appliance,
are excluded fromtowarranty
replace or repair house
coverage.
fuses, or resulting
4. Damage to correctfrom house wiring or
accident, plumbing.
alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with
3. electrical
Service calls to repair or
or plumbing replace
codes, or useappliance light bulbs,
of products air filtersby
not approved orKitchenAid.
water filters. Consumable parts are excluded from warranty coverage.
4.
5. Damage
Cosmeticresulting
damage,from accident,
including alteration,
scratches, dents,misuse,
chipsabuse,
or other fire, flood, acts
damage to the offinish
God, of improper
your majorinstallation,
appliance, installation
unless such not in accordance
damage resultswith
from
electrical
defects inor plumbing
materials orcodes,
workmanshipor use of products
and is reported not approved
to KitchenAid by KitchenAid.
within 30 days from the date of purchase.
5. Any
6. Cosmetic
food or damage,
medicine including
loss due scratches, dents,
to refrigerator orchips
freezeror product
other damage failures. to the finish of your major appliance, unless such damage results from
defects and
7. Pickup in materials
delivery. or Thisworkmanship
major appliance and isisreported
intendedtotoKitchenAid
be repairedwithin in your 30home.
days from the date of purchase.
6. Repairs
8. Any foodtoorparts medicine loss due
or systems to refrigerator
resulting or freezer product
from unauthorized modifications failures. made to the appliance.
7. Expenses
9. Pickup andfor delivery.
travel andThistransportation
major appliance for is intended
product to beifrepaired
service your major in your home.is located in a remote area where service by an authorized
appliance
8. KitchenAid
Repairs to parts serviceror systems resulting from unauthorized modifications made to the appliance.
is not available.
9. The
10. Expenses
removal forandtravel and transportation
reinstallation for product
of your major appliance service
if it if
is your major
installed in appliance is located
an inaccessible in a remote
location or is notarea whereinservice
installed by an with
accordance authorized
KitchenAid
KitchenAid'sservicerpublished is not available.instructions.
installation
10. Replacement
11. The removal and partsreinstallation
or repair labor of your majorappliances
on major appliance ifwith it isoriginal
installedmodel/serial
in an inaccessible
numbers location or isbeen
that have not installed
removed,inaltered
accordance
or cannotwith be easily
KitchenAid's
determined. published installation instructions.
11.
12. Replacement
Discoloration,parts rust ororoxidation
repair labor on major steel
of stainless appliances
surfaces. with original model/serial numbers that have been removed, altered or cannot be easily
Thedetermined.
cost of repair or replacement under these excluded circumstances shall be borne by the customer.
12. Discoloration, rust or oxidation of stainless steel surfaces.
The cost of repair or replacement under these excluded DISCLAIMER circumstancesOF IMPLIED shallWARRANTIES
be borne by the customer.
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
DISCLAIMER OF IMPLIED
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow WARRANTIES
limitations on the durationINCLUDING
IMPLIED WARRANTIES, of implied warranties
ANY IMPLIED of merchantability
WARRANTY OF or MERCHANTABILITY
fitness, so this limitation OR may
IMPLIEDnot apply to you. This
WARRANTY warrantyFOR
OF FITNESS givesAyou specific
legal rights, and
PARTICULAR you also may
PURPOSE, AREhave LIMITED otherTO rights
ONEthat YEAR varyORfrom THE state to state or
SHORTEST province
PERIOD to province.
ALLOWED BY LAW. Some states and provinces do not allow
limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific
legal rights, and you also may have other DISCLAIMER
rights that vary OFfrom
REPRESENTATIONS
state to state or province OUTSIDE OF WARRANTY
to province.
KitchenAid makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations
contained in this Warranty. If you want aDISCLAIMER longer or moreOF REPRESENTATIONS
comprehensive warranty thanOUTSIDE OF WARRANTY
the limited warranty that comes with this major appliance, you
should
KitchenAidask KitchenAid or your retailer about buying
makes no representations the quality,an extended
durability,warranty.
or need for service or repair of this major appliance other than the representations
contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you
should ask KitchenAid or LIMITATION
your retailerOF REMEDIES;
about buying an EXCLUSION
extended warranty. OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. KITCHENAID
SHALL NOT BE LIABLELIMITATION FOR INCIDENTAL OF REMEDIES;
OR CONSEQUENTIAL EXCLUSION OF INCIDENTAL
DAMAGES. Some states ANDand CONSEQUENTIAL
provinces do not allow DAMAGESthe exclusion or limitation of
incidental
YOUR SOLE or consequential
AND EXCLUSIVE damages,
REMEDY so these
UNDER limitations and exclusions
THIS LIMITED WARRANTY maySHALL
not applyBE to you. ThisREPAIR
PRODUCT warrantyAS gives you specific
PROVIDED legalKITCHENAID
HEREIN. rights, and you
also may
SHALL NOThave BEother
LIABLE rightsFOR that vary from state
INCIDENTAL to state or provinceDAMAGES.
OR CONSEQUENTIAL to province.Some states and provinces do not allow the exclusion or limitation of
incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you
If outside
also may havethe 50other
United States
rights that and
varyCanada,
from state contact
to state youror authorized
province toKitchenAidprovince. dealer to determine if another warranty applies. 2/11
For additional
If outside the 50 product
Unitedinformation,
States and Canada, in the U.S.A.,
contact visit
yourwww.kitchenaid.com.
authorized KitchenAid dealer to determine if another warranty applies. 2/11
In Canada, visit www.kitchenaid.ca.
For
If additional
you do not have product information,
access to the Internetin the and
U.S.A.,
youvisitneed www.kitchenaid.com.
assistance using your product or you would like to schedule service, you may contact
In Canada, at
KitchenAid thewww.kitchenaid.ca.
visit number below.
If you your
Have do not have access
complete modeltonumberthe Internet ready.andYouyou canneedfind assistance
your modelusing number yourandproduct
serial or you would
number on thelike to schedule
label, located on service, you may
the inside wall contact
of the ice
KitchenAid at the number below.
maker.
Have
For your complete
assistance modelinnumber
or service the U.S.A., ready.
callYou can find your model
1-800-422-1230. In Canada, number calland serial number on the label, located on the inside wall of the ice
1-800-807-6777.
maker.
If you need further assistance, you can write to KitchenAid with any questions or concerns at the address below:
For assistance
In the U.S.A.: or service in the U.S.A., call 1-800-422-1230. In Canada, call In1-800-807-6777.
Canada:
If you need further
KitchenAid Brand assistance,
Home Appliances you can write to KitchenAid with any questions or concernsBrand
KitchenAid at the Home
address below:
Appliances
In the U.S.A.: eXperience Center
Customer In Canada:
Customer eXperience Centre
KitchenAid
553 BensonBrand RoadHome Appliances KitchenAid
200 6750 Brand Century Home
Ave.Appliances
Customer
Benton Harbor, eXperience Center
MI 49022-2692 Customer
Mississauga, eXperience
Ontario L5N Centre 0B7
553 Benson Road
Please include a daytime phone number in your correspondence. 200 6750 Century Ave.
Benton
Please keepHarbor, MI 49022-2692
all provided instructions and your model number information for future Mississauga,
reference.Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
Please keep all provided instructions and your model number information for future reference. 8 8/13
W10541605B
8
/ 2013 KitchenAid. Used under license in Canada. All rights reserved. Printed in U.S.A.
8/13
W10541605B
/ 2013 KitchenAid. Used under license in Canada. All rights reserved. n 3-17
Printed in U.S.A.
Controls and Operating Instructions
8VHU*XLGH
8VHU*XLGH
,FH0DNHU
,FH0DNHU
/($51025(
/($51025(
In an effort to conserve natural resources, this ice maker includes a condensed User Guide. A complete User Guide can
In an
be
In an effort to
to conserve
downloaded
effort conserve natural resources,
resources, this
at www.maytag.com/manuals.
natural this ice
ice maker
maker includes
includes aa condensed
condensed User
User Guide.
Guide. A
A complete
complete User
User Guide
Guide can
can
be downloaded
downloaded at at www.maytag.com/manuals.
be
The model numberwww.maytag.com/manuals.
is located on the inside of the ice maker.
The model
The model number
number isis located
located on
on the
the inside
inside of
of the
the ice
ice maker.
maker.
Register your ice maker at www.maytag.com
Register
Register your ice maker at www.maytag.com
www.maytag.com
Para unayour ice de
version maker at instrucciones
estas en espaol, visite www.maytag.com.
Para una
Para una version
version de
de estas
estas instrucciones
instrucciones enen espaol,
espaol, visite www.maytag.com.
visite www.maytag.com.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the
All safety
All safety messages
messages
instructions will tell
will tell you
are not followed. you what
what the
the potential
potential hazard
hazard is,
is, tell
tell you
you how
how to
to reduce
reduce the
the chance
chance of
of injury,
injury, and
and tell
tell you
you what
what can
can happen
happen ifif the
the
instructions are
instructions are not
not followed.
followed.
23(5$7,1*<285,&(0$.(5
23(5$7,1*<285,&(0$.(5
+RZ<RXU,FH0DNHU:RUNV
+RZ<RXU,FH0DNHU:RUNV
When you first start your ice maker, the water pan will fill and the 7KH,FH0DNLQJ3URFHVV
When you
system
When you first
willfirst
rinse start your
itself
start ice maker,
before
your ice maker, the
startingthe water
to water
make panpan will fill
ice. The
will fill and the
rinsing
and the
process 7KH,FH0DNLQJ3URFHVV
1. Water is constantly circulated over a
system
takes
system will rinse
about
will rinse itself before
5 minutes.
itself before starting
starting to
to make
make ice.
ice. The
The rinsing
rinsing process
process 1. freezing
1. Water is
Water is plate.
constantly
As the
constantly circulated
circulated over aainto
water freezes
over
takes about
takes about 55 minutes.
minutes. freezing
ice, plate. As
the minerals
freezing plate. Asinthe
the
thewater
water
water freezes
are into
freezes into
Under normal operating conditions, the ice maker will cycle at preset
Under normal
normal operating
temperatures.
Under operating
The ice level conditions, the ice
sensor located
conditions, the ice in
maker willstorage
the ice
maker will cycle at
cycle atbin
preset
will
preset ice, the
ice, the minerals
rejected. minerals in the
in the water
This produces water
a sheetareof ice
are
temperatures.
monitor the iceThe
temperatures. The ice level
levels.
ice level sensor
sensor located
located inin the
the ice
ice storage
storage binbin will
will rejected.
with
rejected. This
a lowThis produces
mineral
produces aa sheet
content. sheet of
of ice
ice
monitor the
monitor the iceice levels.
levels. with aa low
with low mineral
mineral content.
content.
IMPORTANT: If the water supply to the ice maker is turned off, be sure
IMPORTANT:
to IfIf the
set the ice maker
IMPORTANT: the water
water supply
controlsupply to the
to OFF.
to the ice
ice maker
maker is is turned
turned off,
off, be
be sure
sure
to set
to set the
the ice
ice maker
maker control
control to
to OFF.
OFF.
3-18 n W10541614B
W10541614B
W10541614B
Controls and Operating Instructions
2. When the desired thickness is reached, :DWHU)LOWUDWLRQ6\VWHP
the ice sheet is released and slides onto
a cutter grid. The grid divides the sheet
into individual cubes.
Do not use with water that is microbiologically unsafe or
3. The water containing the rejected of unknown quality without adequate disinfection before
minerals is drained after each freezing or after the system. Systems certified for cyst reduction
cycle. may be used on disinfected waters that may contain
4. Fresh water enters the machine for the next ice making cycle. filterable cysts.
5. Cubes fall into the storage bin. When the
bin is full, the ice maker shuts off
automatically and restarts when more ice is ,QVWDOOWKH:DWHU)LOWHU
needed. The ice bin is not refrigerated, and 1. Locate the accessory packet in the ice maker and remove the
some melting will occur. The amount of water filter.
melting varies with room temperature. 2. Take the water filter out of its packaging and remove the cover from
NOTE: As the room and water temperatures the O-rings. Be sure the O-rings are still in place after the cover is
vary, so will the amount of ice produced and removed.
stored. This means that higher operating temperatures result in
reduced ice production.
8VLQJWKH&RQWUROV
1. To start ice production, press ON/OFF.
2. To stop ice maker operation, press ON/OFF.
A B C D
NOTES:
Pressing the On/Off button does not shut off power to the ice
maker.
Allow 24 hours to produce the first batch of ice. Discard the first 2
batches produced.
)DVW,FH0RGH
4. Using the arrow pointing to the alignment pin on the side of the
Select the Fast Ice feature when you have an upcoming need for a filter and the arrow inside the control housing, align the alignment
large amount of ice and the ice bin is low or empty. Fast Ice mode will pin with the cutout notch and insert the filter into the housing.
produce a greater quantity of ice in a 24-hour period.
Press FAST ICE while the ice maker is on. The indicator light will A B
illuminate.
C
Press FAST ICE again to turn off the Max Ice feature. The indicator
light will turn off. D
The Fast Ice mode will be on when you first turn on the product. It
will turn off after 24 hours. To turn Fast Ice back on, press FAST
ICE.
&OHDQ F
It is recommended that you clean the ice maker when the Cleaning
Needed light is illuminated or 9 months has elapsed or ice production
decreases significantly. To clean your ice maker, see Ice Maker
System in the Cleaning section. E
n 3-19
Controls and Operating Instructions
NOTE: If the filter is not correctly locked into the housing, the ice NOTE: There may be some water in the filter. Some spilling may
maker will not produce ice. occur.
3. Install the replacement water filter by following steps 2 through 5 in
the Install the Water Filter section.
A 1RUPDO6RXQGV
Your new ice maker may make sounds that are not familiar to you.
Because the sounds are new to you, you might be concerned about
A. Alignment arrow aligned with locked symbol them. Most of the new sounds are normal. Hard surfaces such as
floors, walls and cabinets can make the sounds seem louder than they
actually are. The following describes the kinds of sounds that might be
7KH:DWHU)LOWHU6WDWXV/LJKW new to you and what may be making them.
The water filter status lights will help you know when to change your You will hear a buzzing sound when the water valve opens to fill the
water filter. water pan for each cycle.
The Order Filter status light will be illuminated when it is time to Rattling noises may come from the flow of the refrigerant or the
order a replacement filter. water line. Items stored on top of the ice maker can also make
The Replace Filter status light will be illuminated when it is time to noises.
replace the filter. The high-efficiency compressor may make a pulsating or high
Replacing the disposable water filter with a new filter will pitched sound.
automatically reset the filter status tracking feature. See Using the Water running over the evaporator plate may make a splashing
Controls. sound.
NOTES: Water running from the evaporator plate to the water pan may make
Replace Filter will remain illuminated if a filter is not installed. a splashing sound.
The Filter status light will flash if the filter is not correctly As each cycle ends, you may hear a gurgling sound due to the
installed or there is an obstruction in the water line. refrigerant flowing in your ice maker.
You may hear air being forced over the condenser by the condenser
5HSODFHWKH:DWHU)LOWHU fan.
To purchase a replacement water filter, see Accessories. During the harvest cycle, you may hear a thud when the ice sheet
Replace the disposable water filter when indicated on the water filter slides from the evaporator onto the cutter grid.
status display or at least every 9 months. If the ice making rate When you first start the ice maker, you may hear water running
decreases before the Replace Filter light illuminates, then replace the continuously. The ice maker is programmed to run a rinse cycle
filter. before it begins to make ice.
1. Locate the water filter compartment in the right-hand side of the
If the ice maker is connected to a water supply pressure in excess
control housing. See Step 3 in the Install Water Filter section.
of 60 psi, you may hear a loud sound during water filling associated
2. Turn the water filter counterclockwise (to the left), and pull it with the flow of water through the inlet valve. Call a licensed,
straight out of the compartment. qualified plumber to determine the best method to reduce the
supply water pressure (50 psi is recommended).
&$5,1*)25<285,&(0$.(5
&OHDQLQJ
The ice making system and the air cooled condenser need to be NOTE: Use one 16 oz (473 mL) bottle of approved ice maker cleaner.
cleaned regularly for the ice maker to operate at peak efficiency and to To order, see Accessories.
avoid premature failure of system components. See the Ice Maker 1. Press the ON/OFF button.
System and the Condenser sections.
2. Wait 5 to 10 minutes for the ice to fall into the storage bin. Remove
all ice from the storage bin.
([WHULRU6XUIDFHV
3. Unscrew the drain cap from the bottom of the water pan located
Wash the exterior enamel surfaces and gaskets with warm water and
inside the storage bin as shown. Allow the water to drain
mild soap or detergent. Wipe and dry. Regular use of a good household
completely.
appliance cleaner and wax will help maintain the finish. Do not use
abrasive cleaners on enamel surfaces as they may scratch the finish. 4. Replace the drain cap securely on the water pan. If the drain cap is
loose, water will empty from the water pan and you will have either
For products with a stainless steel exterior, use a clean sponge or soft thin ice or no ice.
cloth and a mild detergent in warm water. Do not use abrasive or harsh
cleaners. Do not use chlorine bleach on the stainless steel surfaces. 5. Read and follow all handling information on the cleaner bottle
before completing the steps below. Use one 16 oz (473 mL) bottle
of approved ice maker cleaner.
,FH0DNHU6\VWHP
Minerals that are removed from water during the freezing cycle will
eventually form a hard scaly deposit in the water system. Cleaning the
system regularly helps remove the mineral scale buildup. How often
you need to clean the system depends upon how hard your water is.
With hard water of 15 to 20 grains/gal. (4 to 5 grains/liter), you may
need to clean the system as often as every 9 months.
3-20 n
Controls and Operating Instructions
6. Pour one bottle of solution into the water pan. Fill the bottle twice
with tap water and pour it into the water pan. WARNING
A
B
Electrical Shock Hazard
Disconnect power before cleaning.
Replace all parts and panels before operating.
A. Water pan
B. Drain cap Failure to do so can result in death or electrical shock.
7. Press the CLEAN button. See Using the Controls. The light will
1. Unplug ice maker or disconnect power.
blink, indicating that the cleaning cycle is in process. When the
Cleaning Complete light is illuminated (approximately 2. Remove the 2 screws in the lower access panel and the 2 screws
70 minutes), the cleaning cycle is complete. During the cleaning from the base grille area of the front panel support.
cycle, the system will both clean and rinse itself. 3. Pull the bottom forward and then pull down to remove the lower
8. After the cleaning cycle is complete, remove the drain cap from the access panel.
water pan. Look for any cleaning solution left in the water pan. If
cleaning solution drains from the water pan, you should run the
clean cycle again. Be sure to refill the water pan with cleaner
before starting the clean cycle again. Be sure to replace the drain
cap securely on the water pan. If the drain cap is loose, water will
empty from the water pan and you will have either thin ice or no
ice.
NOTE: Severe scale buildup may require repeated cleaning with a
fresh quantity of cleaning solution.
9. Press the ON/OFF button to resume ice production. 4. Remove dirt and lint from the condenser fins and the unit
compartment with a brush attachment on a vacuum cleaner.
&RQGHQVHU
$'LUW\RU&ORJJHG&RQGHQVHU
Obstructs proper airflow. A
Reduces ice making capacity.
Causes higher than recommended operating temperatures which
may lead to component failure.
A. Condenser fins
$&&(6625,(6
To order accessories, in the U.S.A., visit our web site www.maytag.com/accessories or call 1-800-901-2042.
In Canada, visit our web site www.whirlpoolparts.ca or call 1-800-807-6777.
:DWHU)LOWHU DIIUHVK
6WDLQOHVV6WHHO:LSHV
Order Part Number F2WC9I1 or ICE2 In U.S.A., order Part Number W10355049
&OHDQHU In Canada, order Part Number W10355049B
Order Part Number 4396808 DIIUHVK
.LWFKHQ $SSOLDQFH&OHDQHU
DIIUHVK
6WDLQOHVV6WHHO&OHDQHU In U.S.A., order Part Number W10355010
In U.S.A., order Part Number W10355016 In Canada, order Part Number W10355010B
In Canada, order Part Number W10355016B
n 3-21
Controls and Operating Instructions
352%/(062/9(5
6FDQWKHFRGHDWOHIWZLWK\RXUPRELOHGHYLFHRUYLVLW
KWWSVZZZPD\WDJFRPSURGXFWBKHOSIRUPRUHUHFRPPHQGDWLRQVWKDWPD\KHOS\RX
DYRLGDVHUYLFHFDOO
,FH0DNHU2SHUDWLRQ
WARNING
352%/(0 5(&200(1'('62/87,216
Ice Maker Will Not Operate Check that it is plugged into a grounded 3 prong outlet.
Check that the control is turned on.
Replace the fuse or reset the circuit breaker.
NOTE: If problems continue, contact an electrician.
Room temperature must be above 55F (13C). Otherwise, bin thermostat may sense cold room temperature
and shut off even though the bin is not full of ice. The ice maker may not restart once it does shut off.
If there was a large amount of water added to the ice maker, wait a few minutes for the drain pump to clear. If
there is still water in the bin, check to see whether the drain hose is kinked.
For models with drain pumps, check that the drain hose is not damaged, or kinked or pinched between cabinet
and ice maker. Use only Whirlpool approved drain pump kit, Part Number 1901A.
Ice Maker Seems Noisy Water overflowing the reservoir is normal. This overflow helps to purge minerals that were removed from the
water during the ice making process.
If there is a whooshing sound, check the following things:
Make sure that the water supply is hooked up and turned on.
Make sure that the drain cap is tight and the water drain pan pump is securely attached to the water pan.
If there is ice between the evaporator plate and the cutting grid, check that the ice maker is level. If the ice maker
is level, and the problem persists, run a cleaning cycle.
If the ice maker is connected to a water supply pressure in excess of 60 psi, you may hear a loud sound during
water filling associated with the flow of water through the inlet valve. Call a licensed, qualified plumber to
determine the best method to reduce the supply water pressure (50 psi is recommended).
3-22 n
Controls and Operating Instructions
,FH3URGXFWLRQ
WARNING
352%/(0 5(&200(1'('62/87,216
Ice Maker Runs But Produces Check that the control is turned on.
No Ice
Make sure the water supply is properly connected and turned on.
If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten
the drain cap.
Clean the drain tube.
Check that there are no kinks in the drain line.
Ice Maker Runs But Produces If the accelerated ice production feature is turned on, this feature increases the ice production rate to provide
Very Little Ice you with more ice in the same amount of time.
Room temperatures of more than 90F (32C) will normally reduce ice production.
Dirt or lint may be blocking the airflow through the condenser.
If there is white scale buildup in the ice makers water or freezing system, you should clean the ice maker.
If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten
the drain cap.
Ensure that the cutter grid is securely in place and that its harness plug is connected.
Check that water filter is properly installed.
,FH4XDOLW\
352%/(0 5(&200(1'('62/87,216
Off Taste, Odor or Gray Color If there is unusually high mineral content in the water supply, the water may need to be treated.
in the Ice
If there is mineral scale buildup, clean your ice maker.
Do not store any foods in the ice bin.
Make sure that all packaging materials were removed at the time of installation.
Thin, Soft or Clumps of Ice If there is unusually high mineral content in the water supply, the water may need to be treated.
If there is mineral scale buildup, clean your ice maker.
If there are clumps of ice in the bin and if ice is not used regularly, it will melt and form clumps. Break the clumps
with the ice scoop provided.
n 3-23
3OXPELQJ3UREOHPV
Controls and Operating Instructions
3OXPELQJ3UREOHPV WARNING
Excessive Weight Hazard
WARNING
Use two or more people to move and install ice maker.
Failure to do so can result in back or other injury.
Excessive Weight Hazard
Use two or more people to move and install ice maker.
352%/(0 5(&200(1'('62/87,216
Failure to do so can result in back or other injury.
Water Not Entering Drain If the drain hose is not aligned over the drain, move the ice maker to align the drain.
Properly NOTE: Service technicians cannot repair plumbing problems outside of the ice maker. Call a licensed, qualified
352%/(0 5(&200(1'('62/87,216
plumber.
Water Not Entering Drain If the drain hose is not aligned over the drain, move the ice maker to align the drain.
Properly NOTE: Service technicians cannot repair plumbing problems outside of the ice maker. Call a licensed, qualified
plumber.
3(5)250$1&('$7$6+((7
Ice Maker Water Filtration System
3(5)250$1&('$7$6+((7
Model P6GEG2KL, P6KG2KL, P6WG2KL Capacity 2000 Gallons (7571 Liters)
3-24 n
NSF is a registered trademark of NSF International.
:$55$17<
Controls and Operating Instructions
0$<7$* :$55$17<
0$-25$33/,$1&(:$55$17<
LIMITED WARRANTY
For one year from the date of purchase, 0$<7$*
when this major
0$-25$33/,$1&(:$55$17<
appliance is operated and maintained according to instructions attached to or furnished with the
product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter Maytag) will pay for factory specified parts and repair labor to
correct defects in materials or workmanship. Service must be provided LIMITED by WARRANTY
a Maytag designated service company. This limited warranty is valid only in
the United
For one year States
from or theCanada
date of and applieswhen
purchase, only this
when the major
major appliance appliance is used
is operated and in maintained
the countryaccording
in which ittowas purchased.
instructions Outsidetothe
attached 50 Unitedwith
or furnished States
the
and Canada,
product, Maytagthis brand
limitedofwarranty
Whirlpool does not apply.orProof
Corporation of original
Whirlpool Canada purchase date is Maytag)
LP (hereafter required towill
obtain service
pay for under
factory this limited
specified partswarranty.
and repair labor to
correct defects in materials or workmanship. Service must be provided by a Maytag designated service company. This limited warranty is valid only in
the United States or Canada and applies only when theITEMS EXCLUDED
major appliance FROM
is used WARRANTY
in the country in which it was purchased. Outside the 50 United States
and Canada,
This this limited
limited warranty warranty
does does not apply. Proof of original purchase date is required to obtain service under this limited warranty.
not cover:
1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses,
or to correct house wiring or plumbing. ITEMS EXCLUDED FROM WARRANTY
This limitedcalls
2. Service warranty does
to repair not cover:
or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.
1.
3. Service
Repairs calls
whentoyour correct
majortheappliance
installation of your
is used formajor
other appliance,
than normal, to instruct you on
single-family how to use
household useyour majoritappliance,
or when is used in to replacethat
a manner or repair houseto
is contrary fuses,
or to correct
published userhouse wiring or
or operator plumbing. and/or installation instructions.
instructions
2. Damage
4. Service calls to repair
resulting fromoraccident,
replace appliance
alteration, light bulbs,
misuse, air filters
abuse, or water
fire, flood, actsfilters.
of God,Consumable parts are excluded
improper installation, from
installation notwarranty coverage.
in accordance with electrical
3. orRepairs whencodes,
plumbing your major
or useappliance is used or
of consumables forcleaning
other than normal,not
products single-family
approved by household
Maytag. use or when it is used in a manner that is contrary to
published damage,
5. Cosmetic user or operator
including instructions
scratches,and/or
dents, installation
chips or other instructions.
damage to the finish of your major appliance, unless such damage results from defects
4. inDamage resulting
materials from accident,
or workmanship and alteration,
is reportedmisuse, abuse,
to Maytag within fire,30flood,
daysacts
fromofthe God,
dateimproper installation, installation not in accordance with electrical
of purchase.
or plumbing
6. Any food losscodes,
due toorrefrigerator
use of consumables or cleaning
or freezer product products not approved by Maytag.
failures.
5. Costs
7. Cosmetic damage,with
associated including scratches,
the removal from dents, chipsoforyour
your home other damage
major to the for
appliance finish of your
repairs. major
This majorappliance,
appliance unless such damage
is designed results from
to be repaired in thedefects
home
in
and materials or workmanship
only in-home and is reported
service is covered to Maytag within 30 days from the date of purchase.
by this warranty.
6.
8. Any foodtoloss
Repairs partsdueorto refrigerator
systems or freezer
resulting product failures.
from unauthorized modifications made to the appliance.
7.
9. Costs
Expenses associated
for travel with
andthe removal fromfor
transportation your homeservice
product of yourifmajor appliance
your major for repairs.
appliance This in
is located major appliance
a remote is designed
area where service to by
beanrepaired in theMaytag
authorized home
and onlyisin-home
servicer service is covered by this warranty.
not available.
8.
10. Repairs
The removalto parts
andor systems resulting
reinstallation of yourfrom
major unauthorized
appliance if modifications
it is installed inmade to the appliance.
an inaccessible location or is not installed in accordance with published
9. Expenses
installationfor travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Maytag
instructions.
11. servicer is not available.
Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty is void if the
10. factory
The removal
applied and reinstallation
serial number has of your
beenmajor appliance
altered or removedif it isfrom
installed in an inaccessible
your major appliance. location or is not installed in accordance with published
Theinstallation
cost of repairinstructions.
or replacement under these excluded circumstances shall be borne by the customer.
11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty is void if the
factory applied serial number hasDISCLAIMER been altered orOF removed
IMPLIED fromWARRANTIES;
your major appliance. LIMITATION OF REMEDIES
The cost of repair
CUSTOMER'S SOLE orAND
replacement
EXCLUSIVE under these UNDER
REMEDY excluded THIScircumstances
LIMITED WARRANTY shall be borne
SHALLby BEthe customer.
PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED
WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE
SHORTEST PERIOD ALLOWED BY LAW. DISCLAIMER
MAYTAG SHALL OF IMPLIED
NOT BEWARRANTIES;
LIABLE FOR INCIDENTAL LIMITATION OF REMEDIES DAMAGES. SOME STATES AND
OR CONSEQUENTIAL
PROVINCES
CUSTOMER'S DO NOTAND
SOLE ALLOW THE EXCLUSION
EXCLUSIVE REMEDY OR LIMITATION
UNDER THIS LIMITED OF INCIDENTAL
WARRANTY OR SHALL
CONSEQUENTIAL
BE PRODUCT DAMAGES,
REPAIR AS ORPROVIDED
LIMITATIONS ON THE
HEREIN. IMPLIED
DURATION
WARRANTIES, OF IMPLIED
INCLUDING WARRANTIES
WARRANTIES OF OFMERCHANTABILITY
MERCHANTABILITY OROR FITNESS,
FITNESS SOFOR THESE EXCLUSIONS
A PARTICULAR OR LIMITATIONS
PURPOSE, ARE LIMITEDMAY NOTTO ONEAPPLYYEARTOORYOU.
THE
THIS
SHORTESTWARRANTYPERIOD GIVES
ALLOWEDYOU SPECIFIC
BY LAW. LEGAL
MAYTAG RIGHTS,
SHALL AND NOT YOU MAY ALSO
BE LIABLE HAVE OTHEROR
FOR INCIDENTAL RIGHTS WHICH VARYDAMAGES.
CONSEQUENTIAL FROM STATE SOMETO STATE
STATESOR AND
PROVINCE
PROVINCESTO DO PROVINCE.
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
If outside
THIS the 50 United
WARRANTY GIVESStates and Canada,
YOU SPECIFIC LEGALcontact your authorized
RIGHTS, AND YOU Maytag MAY ALSO dealer to determine
HAVE if another
OTHER RIGHTS warranty
WHICH VARY applies.
FROM STATE TO STATE OR10/12
PROVINCE TO PROVINCE.
For additional product information, in the U.S.A., visit www.maytag.com.
If outside
In Canada,thevisit
50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.
www.maytag.ca. 10/12
If you
For do not have
additional access
product to the Internet
information, in the and youvisit
U.S.A., need assistance using your product or you would like to schedule service, you may contact
www.maytag.com.
Maytag
In at the
Canada, number
visit below.
www.maytag.ca.
Have
If you your
do notcomplete modeltonumber
have access ready.and
the Internet Youyou
canneed
find assistance
your modelusing
number and
your serial or
product number on the
you would label,
like located on
to schedule the inside
service, wall contact
you may of the
refrigerator
Maytag at the compartment.
number below.
For assistance
Have or service
your complete modelinnumber
the U.S.A., callYou
ready. 1-800-688-9900. In Canada,
can find your model calland
number 1-800-807-6777.
serial number on the label, located on the inside wall of the
refrigerator compartment.
If you need further assistance, you can write to Maytag with any questions or concerns at the address below:
Forthe
In assistance
U.S.A.: or service in the U.S.A., call 1-800-688-9900. In Canada, call In1-800-807-6777.
Canada:
If you need further assistance,
Maytag Brand Home Appliances you can write to Maytag with any questions or concerns at the Home
Maytag Brand address below:
Appliances
Customer
In the U.S.A.: eXperience Center Customer
In Canada: eXperience Centre
553 Benson Road 200 6750 Century Ave.
Maytag Brand Home Appliances
Benton Harbor, MI 49022-2692 Maytag BrandOntario
Mississauga, Home Appliances
L5N 0B7
Customer eXperience Center Customer eXperience Centre
Please include a
553 Benson Roaddaytime phone number in your correspondence. 200 6750 Century Ave.
Benton
Please keepHarbor, MI 49022-2692
all provided Mississauga,
instructions and your model number information for future reference.Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
Please keep all provided instructions and your model number information for future reference.
8/13
W10541614B
/ 2013 Maytag. Used under license in Canada. All rights reserved. Printed in U.S.A.
W10541614B
/ 2013 Maytag. Used under license in Canada. All rights reserved.
3-25
nPrinted 8/13
in U.S.A.
Controls and Operating Instructions
User Guide
Ice Maker
LEARN MORE
In an effort to conserve natural resources, this ice maker includes a condensed User Guide. A complete User Guide can
be downloaded at www.whirlpool.com/manuals. The model number is located on the inside of the ice maker.
In the U.S.A., register your ice maker at www.whirlpool.com.
In Canada, register your ice maker at www.whirlpool.ca.
Para una version de estas instrucciones en espaol, visite www.whirlpool.com.
You can be killed or seriously injured if you dont immediately follow instructions.
DANGER
You can be killed or seriously injured if you dont follow instructions.
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
NOTES:
Pressing the On/Off button does not shut off power to the ice
maker.
Allow 24 hours to produce the first batch of ice. Discard the first 2
batches produced.
4. Using the arrow pointing to the alignment pin on the side of the
Fast Ice Mode filter and the arrow inside the control housing, align the alignment
Select the Fast Ice feature when you have an upcoming need for a pin with the cutout notch and insert the filter into the housing.
large amount of ice and the ice bin is low or empty. Fast Ice mode will
produce a greater quantity of ice in a 24-hour period. A B
Press FAST ICE while the ice maker is on. The indicator light will C
illuminate.
Press FAST ICE again to turn off the Fast Ice feature. The indicator D
light will turn off.
The Fast Ice mode will be on when you first turn on the product. It
will turn off after 24 hours. To turn Fast Ice back on, press FAST
ICE.
F
Clean
It is recommended that you clean the ice maker when the Cleaning
Needed light is illuminated or 9 months has elapsed or ice production
decreases significantly. To clean your ice maker, see Ice Maker E
System in the Cleaning section. A. Alignment pin D. Cutout notch inside control housing
B. Unlocked symbol E. Arrow pointing to cutout notch
Door Ajar Alarm C. Locked symbol F. Arrow pointing to alignment pin
The Door Ajar Alarm feature sounds an alarm when the ice maker door
is open for 5 minutes. The alarm will repeat every 2 minutes. Close the
door to turn off. The feature then resets and will reactivate when the
door is left open again for 5 minutes.
n 3-27
2
Controls and Operating Instructions
5. Turn the filter clockwise until it locks into the housing. Ensure that Normal Sounds
the alignment arrow on the filter head aligns with the locked
symbol on the control box housing. Your new ice maker may make sounds that are not familiar to you.
NOTE: If the filter is not correctly locked into the housing, the ice Because the sounds are new to you, you might be concerned about
maker will not produce ice. them. Most of the new sounds are normal. Hard surfaces such as
floors, walls and cabinets can make the sounds seem louder than they
actually are. The following describes the kinds of sounds that might be
new to you and what may be making them.
A You will hear a buzzing sound when the water valve opens to fill the
water pan for each cycle.
Rattling noises may come from the flow of the refrigerant or the
water line. Items stored on top of the ice maker can also make
A. Alignment arrow aligned with locked symbol
noises.
The high-efficiency compressor may make a pulsating or high
The Water Filter Status Light pitched sound.
The water filter status lights will help you know when to change your
Water running over the evaporator plate may make a splashing
water filter.
sound.
The Order Filter status light will be illuminated when it is time to
Water running from the evaporator plate to the water pan may make
order a replacement filter.
a splashing sound.
The Replace Filter status light will be illuminated when it is time to
As each cycle ends, you may hear a gurgling sound due to the
replace the filter.
refrigerant flowing in your ice maker.
Replacing the disposable water filter with a new filter will
You may hear air being forced over the condenser by the condenser
automatically reset the filter status tracking feature. See Using the
fan.
Controls.
During the harvest cycle, you may hear a thud when the ice sheet
NOTES:
slides from the evaporator onto the cutter grid.
Replace Filter will remain illuminated if a filter is not installed.
When you first start the ice maker, you may hear water running
The Filter status light will flash if the filter is not correctly continuously. The ice maker is programmed to run a rinse cycle
installed or there is an obstruction in the water line.
before it begins to make ice.
Replace the Water Filter If the ice maker is connected to a water supply pressure in excess
of 60 psi, you may hear a loud sound during water filling associated
To purchase a replacement water filter, see Accessories.
with the flow of water through the inlet valve. Call a licensed,
Replace the disposable water filter when indicated on the water filter qualified plumber to determine the best method to reduce the
status display or at least every 9 months. If the ice making rate supply water pressure (50 psi is recommended).
decreases before the Replace Filter light illuminates, then replace the
filter.
1. Locate the water filter compartment in the right-hand side of the
control housing. See Step 3 in the Install Water Filter section.
2. Turn the water filter counterclockwise (to the left), and pull it
straight out of the compartment.
NOTE: There may be some water in the filter. Some spilling may
occur.
3. Install the replacement water filter by following steps 2 through 5 in
the Install the Water Filter section.
3-28 n
Controls and Operating Instructions
4. Replace the drain cap securely on the water pan. If the drain cap is
loose, water will empty from the water pan and you will have either
thin ice or no ice.
WARNING
5. Read and follow all handling information on the cleaner bottle
before completing the steps below. Use one 16 oz (473 mL) bottle
of approved ice maker cleaner.
6. Pour one bottle of solution into the water pan. Fill the bottle twice
with tap water and pour it into the water pan.
Electrical Shock Hazard
Disconnect power before cleaning.
Replace all parts and panels before operating.
A
Failure to do so can result in death or electrical shock.
B
1. Unplug ice maker or disconnect power.
2. Remove the 2 screws in the lower access panel and the 2 screws
from the base grille area of the front panel support.
A. Water pan
3. Pull the bottom forward and then pull down to remove the lower
B. Drain cap
access panel.
7. Press the CLEAN button. See Using the Controls. The light will
blink, indicating that the cleaning cycle is in process. When the
Cleaning Complete light is illuminated (approximately
70 minutes), the cleaning cycle is complete. During the cleaning
cycle, the system will both clean and rinse itself.
8. After the cleaning cycle is complete, remove the drain cap from the
water pan. Look for any cleaning solution left in the water pan. If
cleaning solution drains from the water pan, you should run the
clean cycle again. Be sure to refill the water pan with cleaner 4. Remove dirt and lint from the condenser fins and the unit
before starting the clean cycle again. Be sure to replace the drain compartment with a brush attachment on a vacuum cleaner.
cap securely on the water pan. If the drain cap is loose, water will
empty from the water pan and you will have either thin ice or no
ice.
NOTE: Severe scale buildup may require repeated cleaning with a
fresh quantity of cleaning solution. A
9. Press the ON/OFF button to resume ice production.
Condenser
A. Condenser fins
A Dirty or Clogged Condenser
Obstructs proper airflow. 5. Replace the lower access panel using the 4 screws.
6. Plug in ice maker or reconnect power.
Reduces ice making capacity.
Causes higher than recommended operating temperatures which
may lead to component failure.
ACCESSORIES
To order accessories, in the U.S.A., visit our web site www.whirlpool.com/accessories or call 1-800-901-2042.
In Canada, visit our web site www.whirlpoolparts.ca or call 1-800-807-6777.
Water Filter affresh Stainless Steel Wipes
Order Part Number F2WC9I1 or ICE2 In U.S.A., order Part Number W10355049
Cleaner In Canada, order Part Number W10355049B
Order Part Number 4396808 affresh Kitchen & Appliance Cleaner
affresh Stainless Steel Cleaner In U.S.A., order Part Number W10355010
In U.S.A., order Part Number W10355016 In Canada, order Part Number W10355010B
In Canada, order Part Number W10355016B
n 3-29
Controls and Operating Instructions
PROBLEM SOLVER
Scan the code at left with your mobile device, or visit www.whirlpool.com/product_help for
recommendations that may help you avoid a service call.
WARNING
Make sure that the drain cap is tight and the water drain pan pump is securely attached to the water pan.
If there is ice between the evaporator plate and the cutting grid, check that the ice maker is level. If the ice maker
is level, and the problem persists, run a cleaning cycle.
If the ice maker is connected to a water supply pressure in excess of 60 psi, you may hear a loud sound during
water filling associated with the flow of water through the inlet valve. Call a licensed, qualified plumber to
determine the best method to reduce the supply water pressure (50 psi is recommended).
3-30 n
5
Controls and Operating Instructions
Ice Production
WARNING
Ice Quality
n 3-31
Plumbing Problems
Controls and Operating Instructions
Plumbing Problems WARNING
Excessive Weight Hazard
WARNING
Use two or more people to move and install ice maker.
Failure to do so can result in back or other injury.
Excessive Weight Hazard
Use two or more people to move and install ice maker.
PROBLEM RECOMMENDED SOLUTIONS
Failure to do so can result in back or other injury.
Water Not Entering Drain If the drain hose is not aligned over the drain, move the ice maker to align the drain.
Properly NOTE: Service technicians cannot repair plumbing problems outside of the ice maker. Call a licensed, qualified
PROBLEM RECOMMENDED SOLUTIONS
plumber.
Water Not Entering Drain If the drain hose is not aligned over the drain, move the ice maker to align the drain.
Properly NOTE: Service technicians cannot repair plumbing problems outside of the ice maker. Call a licensed, qualified
PERFORMANCE DATA SHEET
plumber.
Ice MakerSystem
Water Filtration
tested and certifiedSystem
by NSF
International against NSF/ANSI
Model P6GEG2KL, P6KG2KL, Standard
P6WG2KL 42 forCapacity
the reduction2000
of Gallons (7571 Liters)
Chlorine Taste and Odor.
System tested and certified by NSF
This system has been tested according to NSF/ANSI Standards 42 for theagainst
International reduction of the substances listed below. The concentration of the
NSF/ANSI
indicated substances in water entering the system was reduced to a concentration
Standard less than
42 for the reduction of or equal to the permissible limit for water leaving the
system, as specified in NSF/ANSI Standards 42.
Chlorine Taste and Odor.
Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %
Aesthetic Effects
This system Requirements
has been tested Influent Standards
according to NSF/ANSI Concentration
42 for the reduction ofEffluent
the substancesEffluent
listed below. TheReduction
concentration ofReduction
the
Chlorine Taste/Odor
indicated substances in50%
waterreduction
entering the 1.9727
systemmg/L 2.0 mg/L
was reduced to aconcentration
10% 0.71
less mg/L
than 0.7788
or equal to mg/L
the permissible 70.2 72.81 the
limit for water leaving
Testsystem,
Parameters:as specified
pH = 7.5inNSF/ANSI
0.5 unlessStandards
otherwise42. noted. Flow = 0.50 gpm (1.89 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68F to
Substance Reduction 71.6F (20C to 22C).
NSF Reduction Rated service
Average capacity = 2000 gallons
Influent (7571 liters).Maximum
Challenge Average Minimum % Average %
Aesthetic Effectsthat operational,
It is essential Requirements
maintenance, Influent Concentration Refer toEffluent
and filter replacement the Warranty Effluent Reduction limited
section for the Manufacturers Reduction
requirements
Chlorine Taste/Odor be carried50% out for the product1.9727
reduction to perform
mg/L as advertised.
2.0 mg/L 10% warranty. 0.71 mg/L 0.7788 mg/L 70.2 72.81
TestUse
replacement
Parameters: pH =filter
7.5 P6RFWG2K, P6RFGEG2K,
0.5 unless otherwise noted.P6RFKG2K,
Flow = 0.50 Part
gpm (1.89 Lpm). Pressure = 60 psig (413.7 kPa).
Application Guidelines/Water Supply Parameters
Number
Temp. = 68FICE2.
to 71.6F (20C to 22C). Rated service capacity = 2000 gallons (7571 liters).
Style 1 When the water filter status display changes
It is essential that operational, maintenance, and filter replacement from GOOD Water
ReferSupply
to the Warranty section for City
theorManufacturers
Well limited
to ORDER, order
requirements a newout
be carried filter.
for When the filter
the product indicatoras
to perform reads
advertised. Water Pressure
warranty. 30 - 120 psi (207 - 827 kPa)
REPLACE, it is recommended that you replace the filter.
Use replacement filter P6RFWG2K, P6RFGEG2K, P6RFKG2K, Part Water Temperature 33- 100F (0.6 - 37.8C)
Style 2 ICE2.
Number Press FILTER to check the status of your water filter. If the Application Guidelines/Water Supply Parameters
filter indicator light is yellow and the words ORDER FILTER appear Service Flow Rate 0.50 gpm (1.89 Lpm) @ 60 psi
Style
on the1display
Whenscreen,
the water filter
order status
a new display
filter. If thechanges from GOOD
filter indicator light is Water Supply City or Well
to
red,ORDER, order a new
it is recommended thatfilter.
youWhen
replacethethefilter indicator reads
filter. Water Pressure 30 - 120 psi (207 - 827 kPa)
REPLACE, it is recommended that you replace the filter.
These contaminants are not necessarily in your water supply. While Water Temperature 33- 100F (0.6 - 37.8C)
Style 2 Press FILTER to check the status of
testing was performed under standard laboratory conditions, actualyour water filter. If the
filter indicatormaylightvary.
is yellow and the words ORDER FILTER appear Service Flow Rate 0.50 gpm (1.89 Lpm) @ 60 psi
performance
on the display screen, order a new filter. If the filter indicator light is
The product is for cold water use only.
red, it is recommended that you replace the filter.
Do
Thesenotcontaminants
use with waterare that
notisnecessarily
microbiologically
in yourunsafe or of unknown
water supply. While
quality without
testing adequate
was performed disinfection
under standardbefore or after
laboratory the system.
conditions, actual
Refer to the Warranty
performance may vary. section for the Manufacturers name, address
and telephone
The product is number.
for cold water use only.
Do not use with water that is microbiologically unsafe or of unknown
quality without adequate disinfection before or after the system.
Refer to the Warranty section for the Manufacturers name, address
and telephone number.
3-32 n
NSF is a registered trademark of NSF International. 7
WARRANTY
Controls and Operating Instructions
WARRANTY
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY
LIMITED WARRANTY
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished
with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter
LIMITED Whirlpool) will pay for Factory Specified Parts and repair labor to correct
WARRANTY
defects in materials or workmanship. Service must be provided by a Whirlpool designated service company. This limited warranty is valid only in the
For oneStates
United year from the date
or Canada of applies
and purchase, only when
when this
themajor
majorappliance
applianceisisoperated andcountry
used in the maintained according
in which it was to instructions
purchased. attached
Outside the to
50or furnished
United States
with Canada,
and the product,
this Whirlpool Corporation
limited warranty does notor Whirlpool
apply. Proof Canada LP (hereafter
of original purchase Whirlpool) will pay
date is required tofor Factory
obtain Specified
service underParts and repair
this limited labor to correct
warranty.
defects in materials or workmanship. Service must be provided by a Whirlpool designated service company. This limited warranty is valid only in the
United States or Canada and applies only when the major ITEMS appliance
EXCLUDED is used in theWARRANTY
FROM country in which it was purchased. Outside the 50 United States
and Canada, this limited warranty does not apply. Proof of original purchase date is required to obtain service under this limited warranty.
This limited warranty does not cover:
1. Service calls to correct the installation of your major ITEMS EXCLUDED
appliance, FROM
to instruct youWARRANTY
on how to use your major appliance, to replace or repair house
Thisfuses, or to
limited correct house
warranty does notwiring or plumbing.
cover:
2.
1. Service
Service calls to repair
calls to correctorthe replace appliance
installation light
of your bulbs,
major air filters to
appliance, or instruct
water filters.
you on Consumable
how to useparts are excluded
your major fromtowarranty
appliance, coverage.
replace or repair house
3. Repairs
fuses, orwhen your major
to correct houseappliance is used for other than normal, single-family household use or when it is used in a manner that is contrary to
wiring or plumbing.
2. published
Service calls user
to or operator
repair instructions
or replace appliance and/or
lightinstallation instructions.
bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.
4.
3. Damage resulting
Repairs when yourfrom
major accident,
appliancealteration,
is used formisuse,
otherabuse, fire, flood,
than normal, acts of God,
single-family improper
household useinstallation,
or when it installation
is used in anot in accordance
manner with to
that is contrary
electrical or plumbing codes, or use of consumables or
published user or operator instructions and/or installation instructions. cleaning products not approved by Whirlpool.
5. Damage
4. Cosmeticresulting
damage,from including scratches,
accident, alteration,dents, chipsabuse,
misuse, or other damage
fire, to the
flood, acts offinish
God, of your major
improper appliance,
installation, unless such
installation damage
not in resultswith
accordance from
defects inor
electrical materials
plumbing orcodes,
workmanship
or use of and is reported to
consumables or Whirlpool within 30not
cleaning products days from theby
approved date of purchase.
Whirlpool.
6. Cosmetic
5. Any food loss due to
damage, refrigerator
including or freezer
scratches, product
dents, chipsfailures.
or other damage to the finish of your major appliance, unless such damage results from
7. Costs
defectsassociated
in materials withor the removal from
workmanship andyour home oftoyour
is reported major within
Whirlpool appliance for repairs.
30 days from the This major
date appliance is designed to be repaired in the
of purchase.
home
6. Any andloss
food onlydue
in-home service isorcovered
to refrigerator by this warranty.
freezer product failures.
8. Costs
7. Repairs to parts orwith
associated systems resulting
the removal fromfrom unauthorized
your home of your modifications
major appliancemadefor to repairs.
the appliance.
This major appliance is designed to be repaired in the
9. home
Expenses
and foronlytravel
in-home and transportation
service is covered for product service if your major appliance is located in a remote area where service by an authorized
by this warranty.
Whirlpool
8. Repairs toservicer
parts orissystems
not available.
resulting from unauthorized modifications made to the appliance.
10. The removal and reinstallation
9. Expenses for travel and transportation of your major appliance
for product if it is
service installed
if your majorin appliance
an inaccessible location
is located in a or is notarea
remote installed
whereinservice
accordance
by anwith published
authorized
installationservicer
Whirlpool instructions.
is not available.
11. The
10. Major appliances
removal with original model/serial
and reinstallation of your majornumbersappliance that
if ithave been removed,
is installed altered or location
in an inaccessible cannot be or easily
is not determined. This warranty
installed in accordance is published
with void if the
factory applied
installation serial number has been altered or removed from your major appliance.
instructions.
TheMajor
11. cost appliances
of repair orwith replacement under these
original model/serial excluded
numbers that havecircumstances
been removed, shall be borne
altered by the
or cannot be customer.
easily determined. This warranty is void if the
factory applied serial number has been altered or removed from your major appliance.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
IMPLIED WARRANTIES, INCLUDINGDISCLAIMER WARRANTIESOF OFIMPLIED
MERCHANTABILITYWARRANTIES; OR FITNESS
LIMITATION FOR OFA PARTICULAR
REMEDIES PURPOSE, ARE LIMITED TO ONE
YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
CUSTOMER'S
SOME STATES SOLE AND EXCLUSIVE
AND PROVINCES DO NOT REMEDYALLOW UNDER THIS LIMITED
THE EXCLUSION ORWARRANTY
LIMITATIONSHALL BE PRODUCT
OF INCIDENTAL REPAIR AS PROVIDED
OR CONSEQUENTIAL HEREIN.
DAMAGES, OR
IMPLIED
LIMITATIONS WARRANTIES,
ON THE DURATION INCLUDING OF WARRANTIES
IMPLIED WARRANTIES OF MERCHANTABILITY
OF MERCHANTABILITY OR FITNESS OR FOR A PARTICULAR
FITNESS, SO THESE PURPOSE,
EXCLUSIONS AREORLIMITED TO ONE
LIMITATIONS
YEAR
MAY NOT OR THE
APPLY SHORTEST
TO YOU. PERIOD ALLOWEDGIVES
THIS WARRANTY BY LAW. YOU WHIRLPOOL
SPECIFIC LEGAL SHALLRIGHTS,
NOT BE AND LIABLE YOUFOR MAYINCIDENTAL
ALSO HAVE OROTHER
CONSEQUENTIAL
RIGHTS WHICH DAMAGES.
VARY
SOME
FROM STATES
STATE TO AND PROVINCES
STATE OR PROVINCEDO NOT TOALLOW
PROVINCE. THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR
LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS
MAY
If NOTthe
outside APPLY TO YOU.
50 United THIS
States WARRANTY
and Canada, contactGIVES yourYOUauthorized
SPECIFIC WhirlpoolLEGAL RIGHTS,
dealer to AND YOU MAY
determine ALSO HAVE
if another OTHER
warranty RIGHTS WHICH VARY
applies. 6/12
FROM STATE TO STATE OR PROVINCE TO PROVINCE.
For additional product information, in the U.S.A., visit www.whirlpool.com.
If
Inoutside
Canada, thevisit
50 www.whirlpool.ca.
United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies. 6/12
For additional
If you product
do not have information,
access in the and
to the Internet U.S.A.,
youvisit
need www.whirlpool.com.
assistance using your product or you would like to schedule service, you may contact
Whirlpool the www.whirlpool.ca.
In Canada,atvisit number below.
If you your
Have do not have access
complete modeltonumber
the Internet
ready.and
Youyou
canneed
find assistance
your modelusing your
number andproduct
serial or you would
number like
on the to schedule
label, service,
located on you may
the inside wall contact
of the
Whirlpool atcompartment.
refrigerator the number below.
Have your complete
For assistance modelinnumber
or service ready.
the U.S.A., callYou can find your model
1-800-253-1301. number
In Canada, calland serial number on the label, located on the inside wall of the
1-800-807-6777.
refrigerator compartment.
If you need further assistance, you can write to Whirlpool with any questions or concerns at the address below:
For assistance or service in the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.
In the U.S.A.: In Canada:
If you need further
Whirlpool Brandassistance, you can write to Whirlpool with any questions orWhirlpool
Home Appliances concernsBrand
at the Home
address below:
Appliances
Customer
In the U.S.A.: eXperience Center Customer eXperience Centre
In Canada:
553 Benson
Whirlpool Road
Brand Home Appliances 200 6750
Whirlpool Century
Brand HomeAve.
Appliances
Benton Harbor, MI 49022-2692
Customer eXperience Center Customer eXperience L5N
Mississauga, Ontario 0B7
Centre
Please
553include
BensonaRoad
daytime phone number in your correspondence. 200 6750 Century Ave.
Benton Harbor, MI 49022-2692 Mississauga,
Please keep all provided instructions and your model number information for future Ontario L5N 0B7
reference.
Please include a daytime phone number in your correspondence.
Please keep all provided instructions and your model number information for future reference.
8
8/13
W10541618B
/ 2013 Whirlpool. Used under license in Canada. All rights reserved. Printed in U.S.A.
8
W10541618B
/ 2013 Whirlpool. Used under license in Canada. All rights reserved. n 3-33
Printed
8/13
in U.S.A.
THEORY OF OPERATION
Section 4:
Theory of Operation
Operating Systems
Refrigeration System
Water System
Electrical System
Operational Modes
n 4-1
THEORY OF OPERATION
Operating Systems
WARNING
RECOMMENDED SOLUTIONS
es Check that the control is turned on.
Check that the water supply is properly connected and turned on.
If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten
the drain cap.
Clean the drain tube.
Check that there are no kinks in the drain line.
es If the accelerated ice production feature is turned on, this feature increases the ice production rate to provide
you with more ice in the same amount of time.
Room temperatures of more than 90F (32C) will normally reduce ice production.
Dirt or lint may be blocking the airflow through the condenser.
If there is white scale buildup in the ice makers water or freezing system, you should clean the ice maker.
If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten
the drain cap.
Ensure that the cutter grid is securely in place and that its harness plug is connected.
Check that water filter is properly installed.
RECOMMENDED SOLUTIONS
or If there is unusually high mineral content in the water supply, the water may need to be treated.
If there is mineral scale buildup, clean your ice maker.
Do not store any foods in the ice bin.
Make sure that all packaging materials were removed at the time of installation.
If there is unusually high mineral content in the water supply, the water may need to be treated.
If there is mineral scale buildup, clean your ice maker.
If there are clumps of ice in the bin and if ice is not used regularly, it will melt and form clumps. Break the clumps
with the ice scoop provided.
4-2 n
WRU SODWH VR WKDW WKH LFH
TXLFNO\DQGHYHQO\
THEORY OF OPERATION
Operating Systems (Cont.)
n 4-3
THEORY OF OPERATION
Operating Systems (Cont.)
ELECTRICAL SYSTEM
There are 2 new components on this Ice Maker. An
inductor (coil) is wired in series (red wire) with the
condenser fan motor. Its purpose in life is to smooth
out voltage spikes. The unit Thermistor (2 white
wires) signals the control board if the temperature
of the machine compartment exceeds 115 degrees
F. If it does, then during the next harvest cycle the
condenser fan remains on to cool the area. 5 VDC is
EXAMPLE of Ice Maker Water System
:$7(56<67(0&20321(17/2&$7,216
supplied to the Thermistor.
:DWHU'LVWULEXWRU
(YDSRUDWRU
:DWHU/HYHO6HQVRU
:DWHU5HWXUQ7XEH
:DWHU5HFLUFXODWLRQ
3XPS
5HVHUYRLU3DQ
0DQXDO'UDLQ
5HVHUYRLU'UDLQ3XPS
'UDLQ2YHURZ
:DWHU9DOYH2XWOHW7XEH %LQ'UDLQ
0HDVXUHG)LOO
:DWHU,QOHW9DOYH
)URP:DWHU6XSSO\
4-4 n
THEORY OF OPERATION
Operating Systems (Cont.)
OPERATIONAL MODES
OPERATIONAL MODES
main operational modes for the During the Freeze mode, some of the hot gas
Thereisare
e detailed operation fourinmainthat
found operational During
modes for accumulating
is in the condenser the the Freeze mode, some of the hot gas
tube,
n page 6-5): ice maker (more detailed operation
condenses is found
to a liquid, in that
and remains is in the condenser accumulating tube,
in the ac-
the ow chart on page 6-5): tube.
cumulating condenses to a liquid, and remains in the ac-
Freeze During the later stages of the Freeze cumulating
mode, as tube.
the ice slab forms on the evaporator freezing
During the later stages of the Freeze mode, as
Harvest
plate, some of the refrigerant passing the through
ice slab forms on the evaporator freezing
Diagnostics) Clean the evaporator will not evaporate intoplate, a gas,some
but of the refrigerant passing through
G CYCLE Service (Diagnostics)
will remain a liquid. This liquid refrigerant will
the evaporator will not evaporate into a gas, but
settle in the accumulator, while the refrigerant
e are two possible Off cycles
ICE MAKING CYCLE
er. They occur when: vapor is sucked off through the suction will tube
remainat a liquid. This liquid refrigerant will
In addition, there arethe twotoppossible settle in the accumulator, while the refrigerant
Off cyclesThis accumulated
of the accumulator.
is full of ice and the LED is il-
for the ice maker. They
liquid occur when:
refrigerant will eventually be vapor
directed is to
sucked off through the suction tube at
d ON/OFF (Idle mode).
the evaporator to quickly
1. The bin is full of ice and the LED is il- warm the the top
evaporator of the accumulator. This accumulated
/OFF button has been
luminated
plate during the Harvest mode. liquid refrigerant will eventually be directed to
The ON/OFF LED will go out. ON/OFF (Idle mode).
the
NOTE: It is very important that the accumulator evaporator to quickly warm the evaporator
em
2. The "ON/OFFis button
not tilted has
out of been
a horizontal plate
position. If during
moved, the Harvest mode.
pressed. The it ON/OFF
could cause LED will go out.
compressor failure.
supplied to the electrical control NOTE: It is very important that the accumulator
e primary side Electrical
of the step-down
SystemWater System is not tilted out of a horizontal position. If moved,
r. The dual transformer reduces The water recirculating pump moves it the
could cause compressor failure.
water
Line Voltage is supplied to the electrical control
4 VAC for the cutter grid, 14 from the reservoir pan up to the distributor,
switches
n light and 12 VAC for theand the primary side of the step-down
drain Water System
where it ows out over the evaporator freez-
ng pumps. Thedual transformer. The
electronic ingdual
plate.transformer reduces The water recirculating pump moves the water
irects 12 VAC120 VAC
to t he to 9.4
water re- VAC for the cutter grid, 14 from the reservoir pan up to the distributor,
Water that does not freeze on the evaporator
reservoir drain VDC for and
pumps, the bin light and
plate runs 12off
VAC for the
the front drain
edge, where
and falls back into it ows out over the evaporator freez-
e hot gas solenoid, condenser pumps.
and recir-culating The electronic
the reservoir, where it is recirculated ingback plate. to
er valve, and compressor.
control board An directs
the12 VAC
water to t he water re-
distributor.
mistor suppliescirculating
temperature Water that does not freeze on the evaporator
and reservoir
As the drain
ice slab pumps,
forms, theand
minerals in the water
e electronic control to determine plate runs off the front edge, and falls back into
120 VAC to the hot aregas
on solenoid,
the surface condenser
of the ice. The water ow-
the reservoir, where it is recirculated back to
ate the harvest cycle.
fan motor, water valve, ing overandthe compressor.
top of the iceAn slab washes these
the water distributor.
System evaporator thermistor minerals
supplies backtemperature
into the water reservoir pan. The
water continues recirculate untilAs
todetermine thethe ice slab forms, the minerals in the water
water
igerant, under information
high pressure, to is
the electronic control to
level in the reservoir drops to the bottom are on the surface of the ice. The water ow-
of the
he condenser, when
where ittochanges
terminate the harvest cycle.
water level sensor. When the watering leveloverin thethe top of the ice slab washes these
nd ows through the drier and
Refrigeration reservoir drops below the sensor, minerals the controlback into the water reservoir pan. The
nto the evaporator. Under lowSystem
terminates the freeze mode and initiates water the
continues to recirculate until the water
evaporator, the liquid refrigerant
The hot gas refrigerant, under
harvest high pressure, is
mode.
om the water owing over the level in the reservoir drops to the bottom of the
forced through the condenser, where itthe
The control signals changes
water valve to fill tolevel
the sensor. When the water level in the
he refrigerant evaporates into water
into a liquid,
w pressure gas, the refrigerant and ows
selectedthrough
water the
level drier and
setting. The touch sensor
reservoir drops below the sensor, the control
ugh the suction capillary
line of thetube
heatinto is
the evaporator.
used to accurately Under lowcorrect volume.
fill to the
terminates the freeze mode and initiates the
he compressor. pressure in the evaporator,
Depending theon
liquid
the refrigerant
ice thickness setting the fill
harvest mode.
absorbs heat from level is calculated
the water owingbyover the amount
the of time it
takes the water
evaporator as the refrigerant to reach the
evaporates intotouch The
sensor control
with signals the water valve to fill to the
a gas. As a low pressure a max time gas,of the
3 min. Thin Ice uses 35
refrigerant selected
ounces water level setting. The touch sensor
(1035cc), Normal
ows back through the suction line of the heat Ice 38.9 ounces (1153cc),
is used to accurately fill to the correct volume.
and Thick Ice 40.9 ounces (1212cc). Depending on the ice thickness setting the fill
exchanger, to the compressor.
level is calculated by the amount of time it
takes the water to reach the touch sensor with
a max time of 3 min. Thin Ice uses 35 ounces
(1035cc), Normal Ice 38.9 ounces (1153cc),
and Thick Ice 40.9 ounces (1212cc).
n 4-5
THEORY OF OPERATION
Operating Systems (Cont.)
4-6 n
COMPONENT ACCESS
Section 5:
Component Access
This section provides service parts access, removal and
installation information concerning Design 15 and 18 Ice
Maker. Refer to the Repair Parts List for your specific model
to see what parts are available for ordering. Access may be
shown to some assemblies that can be disassembled further.
n 5-1
COMPONENT ACCESS
Front Grille Components
WARNING
access the water valve and tech sheet
NUT DRIVER
T15 TORX d^
T20 TORX
T25 TORX
STRAIGHT BLADE DRIVER
PHILLIPS HEAD DRIVER
NEEDLE NOSE PLIERS ^^/E'tdZs>sEd,E/>d^,d
CHANNEL LOCK PLIERS 18 inch
VOM
NEEDLE POINT PROBES
water valve
ts
NOTE: Needle point meter probes must be used for
checking voltages on electronic boards t,/Z>WKK>KZWKZd/KE KE&/Ed/> Zz^d>/D,/Ed
Z^ W
FIGURE 2
FIGURE 1
FIGURE 3
5-2 n
COMPONENT ACCESS
Ice Bin Components
4. Release the quick connect and disconnect the water Ice Bin Door removal
tube. See Figure 4.
1. Unplug ice maker or disconnect power.
2. Support the door so it doesnt get damaged during
the removal process. Use pliers to remove the left
and right side door springs. Remove 2 screws on
,KtdKZDKsZKWKtEKKZ
the left and right side hinge plates and remove door.
See Figure 6.
,KtdKZDKsZKWKtEKKZ
FIGURE 4
5. Pull out the water valve and disconnect the rear water
tube and electrical connection. See Figure 5.
Zz^d>/D,/EdZ/Ed,dZ/EZ
FIGURE 6 Zz^d>/D,/EdZ/Ed,dZ/EZ
FIGURE 7
n 5-3
Zz^d>/D,/EdZ/Ed,dZ/EZ
COMPONENT ACCESS
Ice Bin Components (cont.)
Removing reservoir cover Heater Grid removal
NOTE: The reservoir cover on a 15 swing door ice maker 6. Remove the left and right side hex head screws and
simply unsnaps to remove. The cover on a 18 ice maker disconnect the left and right side wire harnesses.
hEZ^dE,KtdK^^KDWKEEd^
has 2 screws securing it to the control housing. Slide out the heater assembly.
NOTE: A visual check and a resistance can be made of
ZKWKtEKKZ
4. Remove the 2 screws located on the bottom of the
cover. See Figure 8. the heater wire. The heater grid operates on 9.4 VAC.
Resistance is 5 OHMS. See Figure 10.
,KtdK^^KDWKEEd^
KtEKKZ
FIGURE 8
&
& ZDKs/E'd,/Ed,ZD/^dKZ
FIGURE 10
dZ/Ed,dZ/EZ
FIGURE 9 7. Remove 1 screw and the thermistor. See Figure 11.
ZDKs/E'd,/Ed,ZD/^dKZ
FIGURE 11
5-4 n
COMPONENT ACCESS
Ice Bin Components (cont.)
Accessing Ice bin electrical connections Removing reservoir and pumpS
8. Remove the water tube from the left side of the cover 10. Remove 1 hex head screw and remove the reservoir
and roll cover up and out. See Figure 12. assembly. Remove wire harness. See Figure 14.
FIGURE 12
FIGURE 13
FIGURE 15
n 5-5
COMPONENT ACCESS
Ice Bin Components (cont.)
Removing recirculation pump Removing water level sensor
12. Remove the harness connection. Release the pump 13. Disengage the water level switch from the housing.
retainer. Press out the pump. Remove the wire harness connector.
tdZ>s>^E^KZ
tdZ>s>^E^KZ
NOTE: The pump operates on 12 VAC. Resistance is 3.6 NOTE: The water level sensor cannot be checked with a
OHMS. See Figure 16. meter - use the diagnostic program step #10. See Figure 17.
FIGURE 17
FIGURE 16
K,D^st
K,D^st
FIGURE 18
Notes
t,/Z>WKK>KZWKZd/KE KE&/Ed/> Zz^d>/D,/Ed
t,/Z>WKK>KZWKZd/KE KE&/Ed/>
5-6 n
COMPONENT ACCESS
Ice Maker Top Components
3. Remove the 2 hex head screws located in the back of
WARNING the unit. Raise the top.
NOTE: Lay a board across the cabinet under the top and
then cover with a protective blanket. The board and blanket
are needed to provide a working area when the control
compartment is separated from the top. See Figure 20.
ZDKs/E'dKW
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or
electrical shock.
Removing top
FIGURE 20
4. Unsnap water tube on the reservoir cover. Disconnect
the wire harness plugged into the right side of the control
t,/Z>WKK>KZWKZd/KE KE&/Ed/> housing. See FigureZz^d>/D,/Ed
21.
FIGURE 19
FIGURE 21
NOTE: This procedure will prove challenging the first time 7. Remove 2 screws and connectors.
attempted. NOTE: The transformer doesnt have to be removed to
dZE^&KZDZ
5. 5 hex head screws will need to be removed while make voltage and resistance checks. See Figure 24.
supporting the top. Grasp the center of the top with left ts
hand to support top. Screw # 5 needs to be the last to K,D^Z
^^/E'KEdZK>KDWZdDEd
be removed. When the last screw is removed the control
^^/E'KEdZK>KDWZdDEd
housing will separate from the top. See Figure 22.
s
>K,D^Z
ZZs
>K,D^Z
FIGURE 24
h^Z/EdZ&KZZDKs>
t,/Z>WKK>KZWKZd/KE KE&/Ed/> Zz^d>/D,/Ed
t,/Z>WKK>KZWKZd/KE KE&/Ed/>
^^/E'KEdZK>KDWZdDEd
Zz^d>/D,/Ed
>KZWKZd/KE KE&/Ed/>
FIGURE 22 Zz^d>/D,/Ed
h^Z/EdZ&KZZDKs>
t,/Z>WKK>KZWKZd/KE KE&/Ed/>
FIGURE
t,/Z>WKK>KZWKZd/KE 23
KE&/Ed/> Zz^d>/D,/Ed
FIGURE 25
5-8 n
COMPONENT ACCESS
Ice Maker Top Components (cont.)
Removing main Control board
FIGURE 26
Notes
n 5-9
COMPONENT ACCESS
Machine Compartment Components
without
condensate
pump
FIGURE 29
with
condensate
pump
FIGURE 27
5-10 n
COMPONENT ACCESS
Machine Compartment Components (cont.)
1. Unplug ice maker or disconnect power. 1. Unplug ice maker or disconnect power.
2. Remove hose clamp. See Figure 30. NOTE: To replace compressor, condenser fan motor/blade
or hot gas defrost valve raise the cabinet off the base.
hose clamp
2. Remove the 2 base screws. See Figure 32.
ice
maker
plug
FIGURE 30
3. Unplug the ice maker plug from the condensate pump. FIGURE 32
See Figure 30.
4. Remove 4 screws indicated by arrows. See Figure 30. 3. Remove line cord retainer and chassis ground wire.
See Figure 33.
5. Pull the condensate pump out of the machine
compartment. Remove the vent tube hose clamp.
See Figure 31.
hose clamp
FIGURE 33
FIGURE 31
n 5-11
COMPONENT ACCESS
Machine Compartment Components (cont.)
FIGURE 34
Notes
5-12 n
DIAGNOSTICS & TROUBLESHOOTING
Section 6:
Diagnostics and
Troubleshooting
This section contains an example of the Technical Data Sheet
that is shipped with the refrigerator.
NOTE: Always refer to the Technical Data Sheet shipped with
the refrigerator.
n Safety
n Service Diagnostics
n Flush Mode
n Freeze Cycle
n Harvest Mode
n Clean Cycle
n Troubleshooting
n Compressor Resistances
n Wiring Schematic
n Evaporator Thermistor
n 6-1
DIAGNOSTICS & TROUBLESHOOTING
Safety
WARNING DANGER
Keep other people a safe distance away from the appliance to prevent potential injury.
6-2 n
DIAGNOSTICS & TROUBLESHOOTING
Service Diagnostics
WARNING DANGER
Keep other people a safe distance away from the appliance to prevent potential injury.
IMPORTANT: Always used the Technical Data Sheet shipped with the product. The tech sheet information
depicted in this Job Aid is an example only.
dtWK
KE
n 6-3
Z/E'/'EK^d/DK
>
To exit manual diagnostics mode, without stepping through all the components, press the On button.
/
NOTE: After 20 minutes with no key presses, the product exits diagnostic mode and turns off, then starts
back to running.
D/
K>KZWKZd/KE KE&/Ed/> Zz^d>/D,/Ed
6-4 n
d
DIAGNOSTICS & TROUBLESHOOTING
Service Diagnostics (cont.)
Entering and using the diagnostic routine takes a little practice to become familiar with the process.
n 6-5
DIAGNOSTICS & TROUBLESHOOTING
Service Diagnostics (cont.)
&>h^,DK FLUsh MOdE
Tech sheet will incorporate strip circuits showing the sequence of events, time of each event and the
energized circuits.
h
D
d
d^
Zz> &
D
FREEZE cYcLE
&
The freeze cycle normally takes 25-35 minutes depending on ambient conditions and thickness setting
&hE/dD
6-6 n
DIAGNOSTICS & TROUBLESHOOTING
Service Diagnostics (cont.)
hARvEsT MOdE
The length of the harvest cycle takes varies - Maximum time is 16 minutes
cLEAN cYcLE
The clean cycle sequence chart emphasize that hard water necessitates frequent cleaning. Technicians
should emphasize the need for scheduled cleaning of the unit to prevent mineral build up causing hanging
slabs of ice.
n 6-7
DIAGNOSTICS & TROUBLESHOOTING
Troubleshooting
compressor resistances
WARNING DANGER
Keep other people a safe distance away from the appliance to prevent potential injury.
6-8 n
DIAGNOSTICS & TROUBLESHOOTING
Troubleshooting (cont.)
WIRINg schEMATIc
n 6-9
DIAGNOSTICS & TROUBLESHOOTING
Troubleshooting (cont.)
vOLTAgE TEsT POINT chART
VOLTAGE TEST POINTS - MINOTAUR CONTROL BOARD
FROM COLOR TO COLOR CONDITIONS
P1-1 BK P1-2 WH 120VAC INPUT- CONSTANT WHEN PLUGGED IN
PI
P1-4 RD P1-2 WH 120VAC OUTPUT TO COMPRESSOR
P2-1 YL/RD P1-2 WH 120VAC INPUT- WATER FILTER SWITCH FEEDBACK
P2 P2-5 WH/RD P1-2 WH 120VAC OUTPUT TO CONDENSER FAN
P2-6 TN P1-2 WH 120VAC OUTPUT TO WATER VALVE
P3-1 WH/TN P1-1 BK 120VAC NEUTRAL FOR TRANSFORMER
P3-3 V P1-2 WH 120VAC OUTPUT TO HOT GAS VALVE
P3 P3-5 GY 4CKT PIN2 RD/BK 12.8 VAC INPUT FROM TRANSFORMER
MAIN CONTROL
6-10 n
DIAGNOSTICS & TROUBLESHOOTING
Troubleshooting (cont.)
>Kd/E'd^dWK/Ed^/EKEdZK>KDWZdDEd
LOcATINg TEsT POINTs IN cONTROL cOMPARTMENT
d
Z^
&^
D/EKZKEEdKZ/Ed/&/d/KE
MAIN BOARd cONNEcTOR IdENTIFIcATION
t,/Z>WKK>KZWKZd/KE KE&/Ed/> Zz^d>/D,/Ed
W W W W
This picture identifies the location of the control board pin connectors.
Refer to the tech sheet thats packed with the product.
W W W
n 6-11
t,/Z>WKK>KZWKZd/KE KE&/Ed/> Zz^d>/D,/Ed
DIAGNOSTICS & TROUBLESHOOTING
Troubleshooting (cont.)
EvAPORATOR ThERMIsTOR
The start ofsWKZdKZd,ZD/^dKZ
a harvest begins when the water is below the touch sensor sensing level or a max time of 25
min. The evap. thermistor is only used to end a harvest cycle.
KE>Z^t/d,
KE>Z^t/d,
t,/Z>WKK>KZWKZd/KE KE&/Ed/>
cONcEALEd REEd sWITch
Zz^d>/D,/Ed
KE
KE K&&
K&&
6-12 n
DIAGNOSTICS & TROUBLESHOOTING
Troubleshooting (cont.)
1901A PUMP kIT
A large percentage of service calls can be attributed to pump installation mistakes.
Installing the pump is relatively easy as long as the installer uses the components included in the kit and
WhDW</d
make no substitutions or try to reuse old components.
Follow the instruction sheet and DO NOT substitute drain hose. Use the corrugated hose only.
,
W
D
/^
,
Wsd
n 6-13
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
Section 7:
Refrigerant Recovery
and Charging
Procedures
This section provides service parts access, removal and
Installation information concerning KitchenAid, Maytag and
Whirlpool dual evaporator French Door Refrigerators.
Key Components
n 7-1
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
Sealed System Repair
WARNING
7-2 n
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
Sealed System Repair (cont.)
Zd^
d^
Z ,
Z Wd&
hs d
^ss ds
d ,s
W
WWWW
^ W
,,
Ds'd Z^
D sKDDK
^ d
, ,'
& hs^s
d^s
t &
h>'
&
^Ks
n 7-3
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
Sealed System Repair (cont.)
<
EtE^/WW
ED
d^
/
/
Edt
<
d
d
^
W
d
7-4 n
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
Sealed System Repair (cont.)
WK/,h
n 7-5
&
Z&
WK/,h
s&
&
Z&
h
Z
/,>
/
h
Z
/,>
/
7-6 n
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
Sealed System Repair (cont.)
WdZZ
^
K
K
K
K
K
K
K
K>
Z
t,'
Z
n 7-7
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
Sealed System Repair (cont.)
Phase Three: Make Repairs
3. Install heat shields to protect the ice maker cabinet and adjacent components before brazing
viii
3. Install heat shields to protect the ice maker cabinet and adjacent components before brazing
7-8 n
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
Sealed System Repair (cont.)
W&
W&
&Z
,
&Z
,
Z
Z
^
K
^
Ks
K
KZ&
Ks
n 7-9
KZ&
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
Sealed System Repair (cont.)
W&
W&
K
K
K
K
K
K
K
K
E/
E/
,'
,'
s
s
d,'
d,'
/,'
7-10 n
/,'
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
Sealed System Repair (cont.)
W&
^
^
K
^
Z
n 7-11
t
Z&
REFRIGERANT RECOVERY AND CHARGING PROCEDURES
,
Sealed System Repair (cont.)
>
>
W&
h
W&>Z^
/
t
W
W
t
d
Z&
,
>
>
h
/
t
W
d
K
/
W
/
EKd^
K
/
7-12
W
n
/
PRODUCT SPECIFICATIONS &
WARRANTY INFORMATION SOURCES
IN CANADA:
FOR PRODUCT SPECIFICATIONS AND WARRANTY INFORMATION CALL
1-800-461-5681