LG 55UH615 Chassis UA65R

Internal Use Only
LED TV
SERVICE MANUAL
CHASSIS : UA65R
MODEL : 55UH615* 55UH615*-U*

CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
P/NO : MFL69413320 (1602-REV00)

CONTENTS
CONTENTS ............................................................................................... 2
SAFETY PRECAUTIONS ......................................................................... 3
SERVICING PRECAUTIONS .................................................................... 4
SPECIFICATION ....................................................................................... 6
ADJUSTMENT INSTRUCTION............................................................... 14
BLOCK DIAGRAM................................................................................... 26
EXPLODED VIEW ................................................................................... 34
DISASSEMBLY........................................................................................ 35
SCHEMATIC CIRCUIT DIAGRAM ............................................ APPENDIX
TROUBLE SHOOTING GUIDE ................................................. APPENDIX
Copyright LG Electronics. Inc. All rights reserved. -2- LGE Internal Use Only
Only for training and service purposes
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC Do not use a line Isolation Transformer during this check.
power line. Use a transformer of adequate power rating as this Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
protects the technician from accidents resulting in personal injury between a known good earth ground (Water Pipe, Conduit, etc.)
from electrical shocks. and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
It will also protect the receiver and it's components from being with 1000 ohms/volt or more sensitivity.
damaged by accidental shorts of the circuitry that may be Reverse plug the AC cord into the AC outlet and repeat AC voltage
inadvertently introduced during the service operation. measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
If any fuse (or Fusible Resistor) in this TV receiver is blown, 0.5 mA.
replace it with the specified. In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
When replacing a high wattage resistor (Oxide Metal Film Resistor, repaired before it is returned to the customer.
over 1 W), keep the resistor 10 mm away from PCB.
Leakage Current Hot Check circuit
Keep wires away from high voltage or high temperature parts.
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed

metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1 M and 5.2 M.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service 2. After removing an electrical assembly equipped with ES
manual and its supplements and addenda, read and follow the devices, place the assembly on a conductive surface such as
SAFETY PRECAUTIONS on page 3 of this publication. aluminum foil, to prevent electrostatic charge buildup or expo-
NOTE: If unforeseen circumstances create conflict between the sure of the assembly.
following servicing precautions and any of the safety precautions 3. Use only a grounded-tip soldering iron to solder or unsolder ES
on page 3 of this publication, always follow the safety precautions. devices.
Remember: Safety First. 4. Use only an anti-static type solder removal device. Some solder
removal devices not classified as anti-static can generate
General Servicing Precautions electrical charges sufficient to damage ES devices.
1. Always unplug the receiver AC power cord from the AC power 5. Do not use freon-propelled chemicals. These can generate
source before; electrical charges sufficient to damage ES devices.
a. Removing or reinstalling any component, circuit board mod- 6. Do not remove a replacement ES device from its protective
ule or any other receiver assembly. package until immediately before you are ready to install it.
b. Disconnecting or reconnecting any receiver electrical plug or (Most replacement ES devices are packaged with leads electri-
other electrical connection. cally shorted together by conductive foam, aluminum foil or
c. Connecting a test substitute in parallel with an electrolytic comparable conductive material).
capacitor in the receiver. 7. Immediately before removing the protective material from the
CAUTION: A wrong part substitution or incorrect polarity leads of a replacement ES device, touch the protective material
installation of electrolytic capacitors may result in an explo- to the chassis or circuit assembly into which the device will be
sion hazard. installed.
2. Test high voltage only by measuring it with an appropriate CAUTION: Be sure no power is applied to the chassis or circuit,
high voltage meter or other voltage measuring device (DVM, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged replace-
Do not test high voltage by "drawing an arc". ment ES devices. (Otherwise harmless motion such as the
3. Do not spray chemicals on or near this receiver or any of its brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity suf-
4. Unless specified otherwise in this service manual, clean ficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10 % (by volume) Acetone and 90 % 1. Use a grounded-tip, low-wattage soldering iron and appropriate
(by volume) isopropyl alcohol (90 % - 99 % strength) tip size and shape that will maintain tip temperature within the
CAUTION: This is a flammable mixture. range or 500 F to 600 F.
Unless specified otherwise in this service manual, lubrication of 2. Use an appropriate gauge of RMA resin-core solder composed
contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25 cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks are Do not use freon-propelled spray-on cleaners.
correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 F to 600 F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 F to 600 F)
Some semiconductor (solid-state) devices can be damaged eas- b. First, hold the soldering iron tip and solder the strand against
ily by static electricity. Such components commonly are called the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors component lead and the printed circuit foil, and hold it there
and semiconductor chip components. The following techniques only until the solder flows onto and around both the compo-
should be used to help reduce the incidence of component dam- nent lead and the foil.
age caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. Alter- splashed solder with a small wire-bristle brush.
natively, obtain and wear a commercially available discharging
wrist strap device, which should be removed to prevent poten-
tial shock reasons prior to applying power to the unit under test.
IC Remove/Replacement 3. Solder the connections.
Some chassis circuit boards have slotted holes (oblong) through CAUTION: Maintain original spacing between the replaced
which the IC leads are inserted and then bent flat against the cir- component and adjacent components and the circuit board to
cuit foil. When holes are the slotted type, the following technique prevent excessive component temperatures.
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique Circuit Board Foil Repair
as outlined in paragraphs 5 and 6 above. Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
Removal board causing the foil to separate from or "lift-off" the board. The
1. Desolder and straighten each IC lead in one operation by following guidelines and procedures should be followed whenever
gently prying up on the lead with the soldering iron tip as the this condition is encountered.
solder melts.
2. Draw away the melted solder with an anti-static suction-type At IC Connections
solder removal device (or with solder braid) before removing To repair a defective copper pattern at IC connections use the
the IC. following procedure to install a jumper wire on the copper pattern
Replacement side of the circuit board. (Use this technique only on IC connec-
1. Carefully insert the replacement IC in the circuit board. tions).
2. Carefully bend each IC lead against the circuit foil pad and
solder it. 1. Carefully remove the damaged copper pattern with a sharp
3. Clean the soldered areas with a small wire-bristle brush. knife. (Remove only as much copper as absolutely necessary).
(It is not necessary to reapply acrylic coating to the areas). 2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
"Small-Signal" Discrete Transistor 3. Bend a small "U" in one end of a small gauge jumper wire and
Removal/Replacement carefully crimp it around the IC pin. Solder the IC connection.
1. Remove the defective transistor by clipping its leads as close 4. Route the jumper wire along the path of the out-away copper
as possible to the component body. pattern and let it overlap the previously scraped end of the
2. Bend into a "U" shape the end of each of three leads remaining good copper pattern. Solder the overlapped area and clip off
on the circuit board. any excess jumper wire.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding At Other Connections
leads extending from the circuit board and crimp the "U" with Use the following technique to repair the defective copper pattern
long nose pliers to insure metal to metal contact then solder at connections other than IC Pins. This technique involves the
each connection. installation of a jumper wire on the component side of the circuit
board.
Power Output, Transistor Device
Removal/Replacement 1. Remove the defective copper pattern with a sharp knife.
1. Heat and remove all solder from around the transistor leads. Remove at least 1/4 inch of copper, to ensure that a hazardous
2. Remove the heat sink mounting screw (if so equipped). condition will not exist if the jumper wire opens.
3. Carefully remove the transistor from the heat sink of the circuit 2. Trace along the copper pattern from both sides of the pattern
board. break and locate the nearest component that is directly con-
4. Insert new transistor in the circuit board. nected to the affected copper pattern.
5. Solder each transistor lead, and clip off excess lead. 3. Connect insulated 20-gauge jumper wire from the lead of the
6. Replace heat sink. nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Diode Removal/Replacement Carefully crimp and solder the connections.
1. Remove defective diode by clipping its leads as close as pos- CAUTION: Be sure the insulated jumper wire is dressed so the
sible to diode body. it does not touch components or sharp edges.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor

Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range 3. Test method

This spec sheet is applied to the LED TV used UA65R chassis (1) Performance: LGE TV test method followed
(2) Demanded other specification
- Safety : UL, CSA, CE, IEC specification
- EMC : FCC, ICES, CE, IEC specification
2. Test condition - Wireless : Wireless HD Specification (Option)
Each part is tested as below without special notice.
(1) Temperature : 25 C 5 C(779F), CST : 40 C5 C

(2) Relative Humidity: 65 % 10 %
(3) Power Voltage
Standard input voltage (100~240V@ 50/60Hz)
* Standard Voltage of each products is marked by models.
(4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
(5) The receiver must be operated for about 20 minutes prior
to the adjustment.
4. General Specification
4.1. Model Specification
No Item Specification Remark
1 Market North America
2 Broadcasting system ATSC / NTSC-M, 64 & 256 QAM
3 Available Channel VHF : 2~13
UHF : 14~69
DTV : 2-69
CATV : 1 ~ 135
CADTV : 1 ~ 135
4 Receiving system Digital : ATSC, 64 & 256 QAM
Analog : NTSC-M
5 Video Input NTSC-M Rear RCA
6 Component Input Y/Cb/Cr, Y/ Pb/Pr Rear RCA
7 HDMI Input HDMI 3 DTV format, Support HDCP2.2/ PC Side,
(HDMI version 1.4)
HDMI 2 DTV format, Support HDCP2.2/ PC Side, Support ARC only HDMI2
(HDMI version 1.4/2.0)
HDMI 1 DTV format, Support HDCP2.2/ PC Side,
(HDMI version 1.4/2.0)
8 Audio Input Component / AV Audio L/R Input ; Rear
Component and av use same jack ; Rear
9 SPDIF out(1EA) Optical Audio out Rear (1EA),
10 USB Input(3EA) EMF, DivX HD, For SVC (download) Side(1)/Rear(2) :JPEG, MP3, DivX HD
(Exception, UA65S: USB 1EA)
4.2. Module Specification
No Item Specification Remark
1 Display Screen Device 65 wide color display module LC650EGE-FJM1 (2D,T120)
LC650EGE-DJM2 (2D,T120)
LC650EGE-FJM3
60 wide color display module HC700EQF-VHEQ1 (2D,M120)
58 wide color display module LC650EQF-FHM1 (2D,T240)
LC650EQF-FHM2 (2D,T240)
LC650EQF-PHF1 (3D,T240)
LC650VQF-FHF1
(3D,T240,Curved)
55 wide color display module LC600EQF-FHM1 (2D,T240)
LC600EQF-PHF1 (3D,T240)
50 wide color display module LC550EQE-FHM1 (2D,T120)
LC550EQE-FHM2 (2D,T120)
LC550EQE-PHF1 (3D,T120)
LC550VQF-FHF1
(3D,T240,Curved)
LC490EQE-XHF1 (3D,T120)
40 wide color display module V400DK1-KE1(2D,T120)
2 Aspect Ratio 16:9 All
4 Operating Environment TFT 1) Temp. : 0 ~ 40 deg LGE SPEC
2) Humidity : 0 ~ 85%
ALEF Temp. : 0 ~ 50 deg
Humidity : 20 ~ 90%
5 Storage Environment TFT Temp. : -20 ~ 60 deg
Humidity : 10 ~ 90%
ALEF Temp. : -20 ~ 60 deg
Humidity : 10 ~ 90%
6 Input Voltage AC100 ~ 240V, 50/60Hz
7 Display Colors 1.07 B (10-bit) LGD
1.07G colors (8-bit+FRC) V580DJ2-KS5
1.067G V500DJ2-KS5
Surface Treatment Hard coating (2H), Anti-glare
5. External input format
5.1. 2D Mode
5.1.1. Component input(Y, CB/PB, CR/PR)
No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed
1 720*480 15.73 60 13.5135 SDTV ,DVD 480I
2 720*480 15.73 59.94 13.5 SDTV ,DVD 480I
3 720*480 31.50 60 27.027 SDTV 480P
4 720*480 31.47 59.94 27.0 SDTV 480P
5 1280*720 45.00 60.00 74.25 HDTV 720P
6 1280*720 44.96 59.94 74.176 HDTV 720P
7 1920*1080 33.75 60.00 74.25 HDTV 1080I
8 1920*1080 33.72 59.94 74.176 HDTV 1080I
9 1920*1080 67.500 60 148.50 HDTV 1080P
10 1920*1080 67.432 59.94 148.352 HDTV 1080P
5.1.2. HDMI Input (PC/DTV)
No. Resolution H-freq(kHz) V-freq.(kHz) Pixel clock(MHz) Proposed

HDMI-PC DDC
1 640*350 31.46 70.09 25.17 EGA
2 720*400 31.46 70.08 28.32 DOS O
3 640*480 31.46 59.94 25.17 VESA(VGA) O
4 800*600 37.87 60.31 40.00 VESA(SVGA) O
5 1024*768 48.36 60.00 65.00 VESA(XGA) O
6 1152*864 54.34 60.05 80.00 VESA O
7 1280*1024 63.98 60.02 108.00 VESA (SXGA) O
8 1360*768 47.71 60.01 85.50 VESA (WXGA) O
9 1920*1080 67.5 60 148.5 WUXGA(Reduced Blanking) O
10 3840*2160 67.5 30 297.00 Only UD Model O
11 3840*2160 56.25 25.00 297.00 Only UD Model O
12 3840*2160 54 24 297.00 Only UD Model O
13 4096*2160 53.95 23.97 297 Only UD Model O
14 4096*2160 54 24 297 Only UD Model O
HDMI-DTV
1 640 * 480 31.46 59.94 25.125 SDTV 480P
2 640 * 480 31.5 60 25.125 SDTV 480P
3 720 * 480 31.5 60 27.027 SDTV 480P
4 720 * 480 31.47 59.94 27.00 SDTV 480P
5 1280*720 45.00 60.00 74.25 HDTV 720P
6 1280*720 44.96 59.94 74.176 HDTV 720P
7 1920*1080 33.75 60.00 74.25 HDTV 1080I
8 1920*1080 33.72 59.94 74.176 HDTV 1080I
9 1920*1080 67.50 60 148.50 HDTV 1080P
10 1920*1080 67.43 59.94 148.35 HDTV 1080P
11 1920*1080 27.00 24.00 74.25 HDTV 1080P
12 1920*1080 26.97 23.97 74.176 HDTV 1080P
13 1920*1080 33.75 30.00 74.25 HDTV 1080P
14 1920*1080 33.71 29.97 74.176 HDTV 1080P
15 3840*2160 67.5 30.00 297.00 UDTV 2160P
16 3840*2160 61.43 29.97 296.703 UDTV 2160P
17 3840*2160 56.25 25.00 297.00 UDTV 2160P
18 3840*2160 54.0 24.00 297.00 UDTV 2160P
19 3840*2160 53.95 23.98 296.703 UDTV 2160P
20 3840*2160 135 59.94 594 UDTV 2160P
21 3840*2160 135 60 594 UDTV 2160P
22 4096*2160 53.95 23.98 296.703 UDTV 2160P
23 4096*2160 54 24.00 297 UDTV 2160P
24 4096*2160 56.25 25.00 297 UDTV 2160P
25 4096*2160 61.43 29.97 296.703 UDTV 2160P
26 4096*2160 67.5 30.00 297 UDTV 2160P
27 4096*2160 135 59.94 594 UDTV 2160P
28 4096*2160 135 60.00 594 UDTV 2160P
5.2. 3D Mode
5.2.1. HDMI Input 1.4b (3D supported mode automatically)
No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock VIC 3D input proposed Proposed

(MHz) mode
1 640*480 31.46 / 31.5 59.94/ 60 25.17/25.2 1 Top-and-Bottom Secondary(SDTV 480P)
Side-by-side(half) Secondary(SDTV 480P)
62.93 / 63 59.94/ 60 50.35/50.4 1 Frame packing Secondary(SDTV 480P)
Line alternative (SDTV 480P)
31.46 / 31.5 59.94/ 60 50.35/50.4 1 Side-by-side(Full) (SDTV 480P)
2 720*480 31.46 / 31.5 59.94 / 60 27.00/27.03 2,3 Top-and-Bottom Secondary(SDTV 480P)
Side-by-side(half) Secondary(SDTV 480P)
62.93 / 63 59.94 / 60 54/54.06 2,3 Frame packing Secondary(SDTV 480P)
Line alternative (SDTV 480P)
31.46 / 31.5 59.94 / 60 54/54.06 2,3 Side-by-side(Full) (SDTV 480P)
3 1280*720 44.96 / 45 59.94 / 60 74.18/74.25 4 Top-and-Bottom Primary(HDTV 720P)
Side-by-side(half) Primary(HDTV 720P)
89.91 / 90 59.94 / 60 148.35/148.5 4 Frame packing Primary(HDTV 720P)
Line alternative (HDTV 720P)
44.96 / 45 59.94 / 60 148.35/148.5 4 Side-by-side(Full) (HDTV 720P)
4 1920*1080 33.72 / 33.75 59.94 / 60 74.18/74.25 5 Top-and-Bottom Secondary(HDTV 1080I)
Side-by-side(half) Primary(HDTV 1080I)
67.43 / 67.5 59.94 / 60 148.35/148.5 5 Frame packing Primary(HDTV 1080I)
Field alternative (HDTV 1080I)
33.72 / 33.75 59.94 / 60 148.35/148.5 5 Side-by-side(Full) (HDTV 1080I)
26.97 / 27 23.97 / 24 74.18/74.25 32 Top-and-Bottom Primary(HDTV 1080P)
Side-by-side(half) Primary(HDTV 1080P)
43.94 / 54 23.97 / 24 148.35/148.5 32 Frame packing Primary(HDTV 1080P)
26.97 / 27 23.97 / 24 148.35/148.5 32 Side-by-side(Full) (HDTV 1080P)
28.125 25 74.25 33 Top-and-Bottom Secondary(HDTV 1080P)
Side-by-side(half) Secondary(HDTV 1080P)
56.25 25 148.5 33 Frame packing Secondary(HDTV 1080P)
28.125 25 148.5 33 Side-by-side(Full) (HDTV 1080P)
33.716 / 33.75 29.976 / 30.00 74.18/74.25 34 Top-and-Bottom Primary(HDTV 1080P)
67.432 / 67.5 29.976 / 30.00 148.35/148.5 34 Frame packing Primary(HDTV 1080P)
33.716 / 33.75 29.976 / 30.00 148.35/148.5 34 Side-by-side(Full) (HDTV 1080P)
67.43 / 67.5 59.94 / 60 148.35/148.50 16 Top-and-Bottom Primary(HDTV 1080P)
Copyright LG Electronics. Inc. All rights reserved. - 10 - LGE Internal Use Only
5.2.2. HDMI 1.4/2.0(3D Supported mode manaually)
No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock Proposed 3D input proposed mode

(MHz)
1. 720*480 31.5 60 27.03 SDTV 480P 2D to 3D, Side by Side(Half),
Top & Bottom, Checker Board,
2. 1280*720 45.00 60.00 74.25 HDTV 720P
Frame Sequential,
Row Interleaving, Column Interleaving
3. 1920*1080 33.75 60.00 74.25 HDTV 1080I 2D to 3D, Side by Side(Half),
Top & Bottom
4. 1920*1080 27.00 24.00 74.25 HDTV 1080P 2D to 3D, Side by Side(Half),
Top & Bottom, Checker Board,
5. 1920*1080 28.12 25 74.25 HDTV 1080P
Row Interleaving,
6. 1920*1080 33.75 30.00 74.25 HDTV 1080P Column Interleaving
7. 1920*1080 67.50 60.00 148.5 HDTV 1080P 2D to 3D, Side by Side(Half),
Top & Bottom,
8. 3840*2160 53.95 23.976 296.703 HDTV 2160P
Checker Board,
9. 3840*2160 54 24.00 297.00 HDTV 2160P Single Frame Sequential,
Row Interleaving, Column Interleaving
10. 3840*2160 56.25 25.00 297.00 HDTV 2160P
11. 3840*2160 61.43 29.970 296.703 HDTV 2160P
12. 3840*2160 67.5 30.00 297.00 HDTV 2160P
13. 4096*2160 53.95 23.976 296.703 HDTV 2160P
14. 4096*2160 54 24.00 297.00 HDTV 2160P
15. 4096*2160 56.25 25.00 297.00 HDTV 2160P
16. 4096*2160 61.43 29.970 296.703 HDTV 2160P
17. 4096*2160 67.5 30.00 297.00 HDTV 2160P
18. 3840*2160 135 60 594 HDTV 2160P 2D to 3D, Top & Bottom(half),
Side by Side(half), Port3 Only
19. 4096*2160 135 60 594 HDTV 2160P 2D to 3D, Top & Bottom(half),
Side by Side(half), Port3 Only
5.2.3. HDMI-PC Input (3D) (3D Supported Mode Manually)
No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock Proposed 3D input proposed mode

(MHz)
1. 1024*768 48.36 60 65 HDTV 768P 2D to 3D,
Side by Side(half), Top & Bottom
2. 1360*768 47.71 60 85.5 HDTV 768P 2D to 3D,
Side by Side(half), Top & Bottom
3. 1920*1080 67.500 60 148.50 HDTV 1080P 2D to 3D,
Side by Side(half), Top & Bottom,
Checker Board, Single Frame
Sequential, Row Interleaving,
Column Interleaving
4. 3840*2160 54 24.00 296.703 HDTV 2160P 2D to 3D,
4096*2160 Top & Bottom(half), Side by Side(half),
56.25 25.00 297
67.5 30.00 296.703
5. 3840*2160 135 60 594 HDTV 2160P 2D to 3D,
4096*2160 Top & Bottom(half), Side by Side(half),
Port3 Only
6. Others - - - 640*350 2D to 3D,
720*400 Side by Side(half), Top & Bottom
640*480
800*600
1152*864
5.2.4. RF Input(3D supported mode manually)
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode
1 1280*720 37.500 50 74.25 HDTV 720P 2D to 3D, Side by Side, Top & Bottom
2 1920*1080 28.125 50 74.25 HDTV 1080I 2D to 3D, Side by Side, Top & Bottom
5.2.5. RF Input (3D supported mode automatically)
No. Signal 3D input proposed mode

1 Frame Compatible Side by Side(Half), Top & Bottom
5.2.6. USB, DLNA (Movie) Input (3D supported mode manually)
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) 3D input proposed mode

1 Under 704x480 - - - 2D to 3D
2 Over 704x480 - - - 2D to 3D, Side by Side(Half), Top & Bottom
interlaced
3 Over 704x480 - 60 - 2D to 3D, Side by Side(Half), Top & Bottom,
progressive Checker Board, Row Interleaving,
Column Interleaving, Frame Sequential
4 Over 704x480 - others - 2D to 3D, Side by Side(Half), Top & Bottom,
progressive Checker Board, Row Interleaving,
Column Interleaving
5 Over 2160P - 24/25/30/60 - 2D to 3D, Side by Side(Half),
Top & Bottom, USB Only
5.2.7. USB, DLNA (Photo) Input (3D supported mode manually)
No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) 3D input proposed mode

1 USB(Photo) - - - 2D to 3D, Side by Side(Half), Top & Bottom
5.2.8. USB, DNLA Input (3D supported mode automatically)

1 1080P 33.75 30 - Side by Side(Half), Top & Bottom, Checker Board,
MPO(Photo)
2 2160p 67.5 30 297 MPO(Photo), JPS(Photo)
5.2.9. Component Input(3D supported mode manually)
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1 1280*720 45.00 60.00 74.25 HDTV 720P 2D to 3D,
Side by Side(Half),
2 1280*720 37.500 50 74.25 HDTV 720P
Top & Bottom
3 1920*1080 33.75 60.00 74.25 HDTV 1080I
4 1920*1080 28.125 50.00 74.25 HDTV 1080I
5 1920*1080 27.00 24.00 74.25 HDTV 1080P
6 1920*1080 28.12 25 74.25 HDTV 1080P
7 1920*1080 33.75 30.00 74.25 HDTV 1080P
8 1920*1080 67.50 60.00 148.5 HDTV 1080P
9 1920*1080 56.250 50 148.5 HDTV 1080P
10 Others - - - SDTV
5.2.10. Miracast, Widi (3D supported mode manually)

1 1024X768p - 30 / 60 - 2D to 3D, Side by Side(Half), Top & Bottom
2 1280x720p - 30 / 60 -
3 1920X1080p 30 / 60
4 Others - 2D to 3D
**Remark: 3D Input mode
No. Side by Side Top & Bottom Checkerboard Single Frame Frame Packing Line Column
Sequential Interleaving Interleaving
1
L R LLLLL R
L
R
L
ADJUSTMENT INSTRUCTION
1. Application Range 4. Automatic Adjustment
This spec. sheet applies to UA65R Chassis applied LED TV all 4.1. ADC Adjustment
models manufactured in TV factory ADC adjustment is needed to find the optimum black level and
gain in Analog-to-Digital device and to compensate RGB
deviation.
2. Specification.
(1) Because this is not a hot chassis, it is not necessary to use 4.1.1. Equipment & Condition
an isolation transformer. However, the use of isolation (1) USB to RS-232C Jig
transformer will help protect test instrument (2) M SPG-925 Series Pattern Generator(MSPG-925FA,
(2) Adjustment must be done in the correct order. pattern -65)
(3) The adjustment must be performed in the circumstance of - Resolution : 480i Comp1
25 5C of temperature and 6510% of relative humidity if 1080P Comp1
there is no specific designation - Pattern : Horizontal 100% Color Bar Pattern
(4) The input voltage of the receiver must keep 100~240V, - Pattern level : 0.70.1 Vp-p
50/60Hz - Image
(5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15C
In case of keeping module is in the circumstance of 0C, it

should be placed in the circumstance of above 15C for 2
hours
In case of keeping module is in the circumstance of below
-20C, it should be placed in the circumstance of above 15C
for 3 hours
4.1.2. Adjustment method
* (Caution) When still image is displayed for a period of 20 Using USB, adjust items listed in 3.1 in the other shown in
minutes or longer (especially where W/B scale is 4.1.3.3
strong. Digital pattern 13ch and/or Cross hatch
pattern 09ch), there can some afterimage in the
4.1.3. Adj. protocol
black level area.
Protocol Command Set ACK
Enter adj. mode aa 00 00 a 00 OK00x
3. Adjustment items Source change xb 00 40

xb 00 60
b 00 OK04x (Adjust 480i, 1080p Comp1 )
b 00 OK06x (Adjust 1920*1080 RGB)
3.1. Main PCB check process
Begin adj. ad 00 10
MAC Address Download
ADC adjustment : 480i Comp1, 1920*1080 Comp1 Return adj. OKx (Case of Success)
EDID/DDC download result NGx (Case of Fail)
Above adjustment items can be also performed in Final Read adj. data (main) (main)
Assembly if needed. Both Board-level and Final assembly ad 00 20 000000000000000000000000007c007b006dx
adjustment items can be check using In-Start Menu 1.ADJUST
CHECK. (sub ) (Sub)
ad 00 21 000000070000000000000000007c00830077x
3.2. Final assembly adjustment Confirm adj. ad 00 99 NG 03 00x (Fail)

NG 03 01x (Fail)
White Balance adjustment NG 03 02x (Fail)
RS-232C functionality check OK 03 03x (Success)
PING Test
End adj. ad 00 90 a 00 OK90x
Factory Option setting per destination
Ship-out mode setting (In-Stop) (Ref.) ADC Adj. RS232C Protocol_Ver1.0
3.3. Etc. Adj. order

Ship-out mode aa 00 00 [Enter ADC adj. mode]
Service Option Default xb 00 04
USB Download(S/W Update, Option, Service only) [Change input source to Component1(480i&1080p)]
ISP Download (Option) ad 00 10 [Adjust 480i&1080p Comp1]
xb 00 06 [Change input source to RGB(1024*768)]
ad 00 10 [Adjust 1920*1080 RGB]
aa 00 90 End adj.
4.2. MAC address, ESN, Widevine, HDCP2.0 4.3. LAN Inspection
key D/L 4.3.1. Equipment & Condition
4.2.1. Equipment & Condition Each other connection to LAN Port of IP Hub and Jig
(1) Play file: keydownload.exe
4.2.2. Communication Port connection

(1) Key Write: Com 1,2,3,4 and 115200 (Baudrate)
(2) Barcode: Com 1,2,3,4 and 9600 (Baudrate)
4.2.3. Download process

(1) Select the download items.
(2) Mode check: Online Only
(3) Check the test process : DETECT -> MAC -> Widevine
(4) Play: START
(5) Check of result: Ready, Test, OK or NG
4.3.2. LAN inspection solution
4.2.4. Communication Port connection LAN Port connection with PCB
(1) Connect: PCBA Jig -> RS-232C Port == PC -> RS-232C Network setting at MENU Mode of TV
Port Setting automatic IP
Setting state confirmation
- If automatic setting is finished, you confirm IP and MAC
Address.
4.2.5. Download
(1) Models(MAC + Widevine + ESN): Korea model(K2Lp)
4.3.3. LAN PORT INSPECTION (PING TEST)
(1) Play the LAN Port Test PROGRAM.

(2) Input IP set up for an inspection to Test Program.
* IP Number : 12.12.2.2.
4.3.4. LAN PORT inspection (PING TEST) * Manual Download (Model Name and Serial Number)
(1) Play the LAN Port Test Program.
(2) connect each other LAN Port Jack. If the TV set is downloaded By OTA or Service man,
(3) Play Test (F9) button and confirm OK Message. Sometimes model name or serial number is initialized. ( not
(4) remove LAN CABLE always)
It is impossible to download by bar code scan, so It need
Manual download.
a. Press the INSTART key of ADJ remote controller.

b. Go to the menu 7. Model Number D/L like below photo.
c. Input the Factory model name or Serial number like
below photo.
d. Check the model name INSTART menu -> Factory name

displayed
e. C heck the Diagnostics (DTV country only) -> Buyer
model displayed
4.5. WIFI MAC ADDRESS CHECK

4.5.1. Using RS232 Command
Command Set ACK
4.4. Model name & Serial number Download
Transmission [A][l][][Set ID][][20][Cr] [O][K][x] or [N][G]
4.4.1. Model name & Serial number D/L
P ress Power on key of service remocon.(Baud rate :
Check the menu on in-start
115200 bps)
Connect RS-232C Signal to USB Cable to USB.
Write Serial number by use USB port.
Must check the serial number at Instart menu.
Method & Notice
A. Serial number D/L is using of scan equipment.

B. S etting of scan equipment operated by Manufacturing
Technology Group.
C. Serial number D/L must be conformed when it is produced
in production line, because serial number D/L is mandatory
by D-book 4.0
5. Manual Adjustment 5.2.4. EDID DATA
Reference
5.1. ADC adjustment is not needed because of - HDMI1 ~ HDMI3
OTP (Auto ADC adjustment) - In the data of EDID, bellows may be different by Input mode
0 1 2 3 4 5 6 7 8 9 A B C D E F
5.2. EDID
0x00 00 FF FF FF FF FF FF 00 1E 6D
0x01 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
(The Extended Display Identification Data) 0x02 0F 50 54 A1 8 00 31 40 45 40 61 40 71 40 81 80
/ DDC (Display Data Channel) download 0x03

0x04
01
45
01
00
01
40
01
84
01
63
01
00
02
00
3A
1E
80
66
18
21
71
50
38
B0
2D
51
40
00
58
1B
2C
30
5.2.1. Overview 0x05 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
It is a VESA regulation. A PC or a MNT will display an optimal 0x06 3E 1E 53 10 00 0A 20 20 20 20 20 20
resolution through information sharing without any necessity of 0x07 01 1
user input. It is a realization of Plug and Play. 0x00 02 03 3A F1 4E 10 9F 04 13 05 14 03 02 12 20 21
0x01 22 15 01 29 3D 06 C0 15 07 50
0x02
5.2.2. Equipment 0x03 10 28 10 E3 05 03 01 02 3A 80 18 71 38
Since embedded EDID data is used, EDID download JIG, 0x04 2D 40 58 2C 45 00 40 84 63 00 00 1E 01 1D 80 18
HDMI cable and D-sub cable are not need. 0x05 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 01 1D
Adjust remocon 0x06 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 00 00 1E
0x07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2
5.2.3. Download method

(1) P
ress Adj. key on the Adjust remocon, then select 12.EDID Product ID
D/L. Serial No: Controlled on production line.
By pressing Enter key, enter EDID D/L menu Month, Year: Controlled on production line:
(2) S
elect [Start] button by pressing Enter key, HDMI1 / HDMI2 ex) Monthly : 01 -> 01
/ HDMI3 / HDMI4 are Writing and display OK or NG. Year : 2016 -> 1A'
Model Name(Hex): LGTV
For HDMI EDID
Checksum(LG TV): Changeable by total EDID data.
DVI-D to HDMI or HDMI to HDMI Vendor Specific(HDMI)
5.2.4.1. EDID
# DTS HDMI1 (C/S: 9F,B6)_6G_UHD Deep Color ON
EDID Block 0, Bytes 0-127
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58
40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 02 03 3A F1 50 61 90 22 20 05 04 03 02 01 5D 5E
10 5F 66 62 63 64 29 3D 06 C0 15 07 50 09 57 07 6E
20 03 0C 00 10 00 B8 3C 20 00 80 01 02 03 04 67 D8
30 5D C4 01 78 80 03 E3 05 C0 00 E3 0F 01 10 E3 06
40 07 01 01 1D 80 18 71 1C 16 20 58 2C 25 00 40 84
50 63 00 00 9E 66 21 50 B0 51 00 1B 30 40 70 36 00
60 40 84 63 00 00 1E 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 B6
#DTS HDMI1 (C/S: 9F, 11)_3G_UHD Deep Color OFF #DTS HDMI3 (C/S: 9F, 96 )_6G_UHD Deep Color ON
EDID Block 0, Bytes 0-127 EDID Block 0, Bytes 0-127
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58
40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F

0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 02 03 36 F1 50 61 90 22 20 05 04 03 02 01 5D 5E 0 02 03 3A F1 50 61 90 22 20 05 04 03 02 01 5D 5E
10 5F 66 62 63 64 29 3D 06 C0 15 07 50 09 57 07 6E 10 5F 66 62 63 64 29 3D 06 C0 15 07 50 09 57 07 6E
20 03 0C 00 10 00 B8 3C 20 00 80 01 02 03 04 E3 0E 20 03 0C 00 30 00 B8 3C 20 00 80 01 02 03 04 67 D8
30 61 66 E3 06 07 01 01 1D 80 18 71 1C 16 20 58 2C 30 5D C4 01 78 80 03 E3 05 C0 00 E3 0F 01 10 E3 06
40 25 00 40 84 63 00 00 9E 66 21 50 0 51 00 1B 30 40 07 01 01 1D 80 18 71 1C 16 20 58 2C 25 00 40 84
50 40 70 36 00 40 84 63 00 00 1E 00 00 00 00 00 00 50 63 00 00 9E 66 21 50 B0 51 00 1B 30 40 70 36 00
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60 40 84 63 00 00 1E 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 11 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 96
#DTS HDMI2 (C/S: 9F,A6)_6G_UHD Deep Color ON #DTS HDMI3 (C/S: 9F F1)_3G_UHD Deep Color OFF
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58
40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 02 03 3A F1 50 61 90 22 20 05 04 03 02 01 5D 5E EDID Block 1, Bytes 128-255
10 5F 66 62 63 64 29 3D 06 C0 15 07 50 09 57 07 6E 0 1 2 3 4 5 6 7 8 9 A B C D E F
20 03 0C 00 20 00 B8 3C 20 00 80 01 02 03 04 67 D8 0 02 03 36 F1 50 61 90 22 20 05 04 03 02 01 5D 5E
30 5D C4 01 78 80 03 E3 05 C0 00 E3 0F 01 10 E3 06 10 5F 66 62 63 64 29 3D 06 C0 15 07 50 09 57 07 6E
40 07 01 01 1D 80 18 71 1C 16 20 58 2C 25 00 40 84 20 03 0C 00 30 00 B8 3C 20 00 80 01 02 03 04 E3 0E
50 63 00 00 9E 66 21 50 B0 51 00 1B 30 40 70 36 00 30 61 66 E3 06 07 01 01 1D 80 18 71 1C 16 20 58 2C
60 40 84 63 00 00 1E 00 00 00 00 00 00 00 00 00 00 40 25 00 40 84 63 00 00 9E 66 21 50 0 51 00 1B 30
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 A6 50 40 70 36 00 40 84 63 00 00 1E 00 00 00 00 00 00
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
#DTS HDMI2 (C/S: 9F 01)_3G_UHD Deep Color OFF 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F1
EDID Block 0, Bytes 0-127
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 # AC3 HDMI1 (C/S: 9F,BF)_6G_UHD Deep Color ON
10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 0 1 2 3 4 5 6 7 8 9 A B C D E F
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC
EDID Block 1, Bytes 128-255 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 02 03 36 F1 50 61 90 22 20 05 04 03 02 01 5D 5E 0 02 03 37 F1 50 61 90 22 20 05 04 03 02 01 5D 5E
10 5F 66 62 63 64 29 3D 06 C0 15 07 50 09 57 07 6E 10 5F 66 62 63 64 26 15 07 50 09 57 07 6E 03 0C 00
20 03 0C 00 20 00 B8 3C 20 00 80 01 02 03 04 E3 0E 20 10 00 B8 3C 20 00 80 01 02 03 04 67 D8 5D C4 01
30 61 66 E3 06 07 01 01 1D 80 18 71 1C 16 20 58 2C 30 78 81 03 E3 05 C0 00 E3 0F 01 10 E3 06 07 01 01
40 25 00 40 84 63 00 00 9E 66 21 50 0 51 00 1B 30 40 1D 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00
50 40 70 36 00 40 84 63 00 00 1E 00 00 00 00 00 00 50 9E 66 21 50 B0 51 00 1B 30 40 70 36 00 40 84 63
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60 00 00 1E 00 00 00 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 BF
# AC3 HDMI1 (C/S: 9F,1A)_ 3G_UHD Deep Color OFF # AC3 HDMI3 (C/S: 9F,03)_ 6G_UHD Deep Color ON
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 0 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 01
10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 10 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 26
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 20 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 80
30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 30 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 58
40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 40 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 40
50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 50 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 3A
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 60 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F 70 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F 9F
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 02 03 33 F1 50 61 10 22 20 05 04 03 02 01 5D 5E 0 02 03 37 F1 50 61 90 22 20 05 04 03 02 01 5D 5E
10 5F 66 62 63 64 26 15 07 50 09 57 07 6E 03 0C 00 10 5F 66 62 63 64 26 15 07 50 09 57 07 6E 03 0C 00
20 10 00 B8 3C 20 00 80 01 02 03 04 E3 0E 61 66 E3 20 10 00 B8 3C 20 00 80 01 02 03 04 67 D8 5D C4 01
30 06 07 01 01 1D 80 18 71 1C 16 20 58 2C 25 00 40 30 78 81 03 E3 05 C0 00 E3 0F 01 10 E3 06 07 01 01
40 84 63 00 00 9E 66 21 50 B0 51 00 1B 30 40 70 36 40 1D 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00
50 00 40 84 63 00 00 1E 00 00 00 00 00 00 00 00 00 50 9E 66 21 50 B0 51 00 1B 30 40 70 36 00 40 84 63
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60 00 00 1E 00 00 00 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1A 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 9F
# AC3 HDMI2 (C/S: 9F,AF)_ 6G_UHD Deep Color ON # AC3 HDMI3 (C/S: 9F,FA)_3G_UHD Deep Color OFF
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58
40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 02 03 37 F1 50 61 90 22 20 05 04 03 02 01 5D 5E 0 02 03 33 F1 50 61 10 22 20 05 04 03 02 01 5D 5E
10 5F 66 62 63 64 26 15 07 50 09 57 07 6E 03 0C 00 10 5F 66 62 63 64 26 15 07 50 09 57 07 6E 03 0C 00
20 10 00 B8 3C 20 00 80 01 02 03 04 67 D8 5D C4 01 20 30 00 B8 3C 20 00 80 01 02 03 04 E3 0E 61 66 E3
30 78 81 03 E3 05 C0 00 E3 0F 01 10 E3 06 07 01 01 30 06 07 01 01 1D 80 18 71 1C 16 20 58 2C 25 00 40
40 1D 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 40 84 63 00 00 9E 66 21 50 B0 51 00 1B 30 40 70 36
50 9E 66 21 50 B0 51 00 1B 30 40 70 36 00 40 84 63 50 00 40 84 63 00 00 1E 00 00 00 00 00 00 00 00 00
60 00 00 1E 00 00 00 00 00 00 00 00 00 00 00 00 00 60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 AF 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FA
# AC3 HDMI2 (C/S: 9F,0A)_3G_UHD Deep Color OFF # PCM HDMI1 (C/S: 9F,31)_6G_UHD Deep Color ON
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58
40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 02 03 33 F1 50 61 10 22 20 05 04 03 02 01 5D 5E 0 02 03 34 F1 50 61 90 22 20 05 04 03 02 01 5D 5E
10 5F 66 62 63 64 26 15 07 50 09 57 07 6E 03 0C 00 10 5F 66 62 63 64 23 09 57 07 6E 03 0C 00 10 00 B8
20 20 00 B8 3C 20 00 80 01 02 03 04 E3 0E 61 66 E3 20 3C 20 00 80 01 02 03 04 67 D8 5D C4 01 78 80 03
30 06 07 01 01 1D 80 18 71 1C 16 20 58 2C 25 00 40 30 E3 05 C0 00 E3 0F 01 10 E3 06 07 01 01 1D 80 18
40 84 63 00 00 9E 66 21 50 B0 51 00 1B 30 40 70 36 40 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21
50 00 40 84 63 00 00 1E 00 00 00 00 00 00 00 00 00 50 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0A 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 31
# PCM HDMI1 (C/S: 9F,8C)_3G_UHD Deep Color OFF # PCM HDMI3 (C/S: 9F,11)_6G_UHD Deep Color ON
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58
40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F 70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 02 03 30 F1 50 61 10 22 20 05 04 03 02 01 5D 5E 0 02 03 34 F1 50 61 90 22 20 05 04 03 02 01 5D 5E
10 5F 66 62 63 64 23 09 57 07 6E 03 0C 00 10 00 B8 10 5F 66 62 63 64 23 09 57 07 6E 03 0C 00 30 00 B8
20 3C 20 00 80 01 02 03 04 E3 0E 61 66 E3 06 07 01 20 3C 20 00 80 01 02 03 04 67 D8 5D C4 01 78 80 03
30 01 1D 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 30 E3 05 C0 00 E3 0F 01 10 E3 06 07 01 01 1D 80 18
40 00 9E 66 21 50 B0 51 00 1B 30 40 70 36 00 40 84 40 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21
50 63 00 00 1E 00 00 00 00 00 00 00 00 00 00 00 00 50 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8C 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 11
# PCM HDMI2 (C/S: 9F,21)_6G_UHD Deep Color ON # PCM HDMI3 (C/S: 9F,6C)_3G_UHD Deep Color OFF
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 0 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 01
10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 10 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 26
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 20 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80 80
30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 30 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58 58
40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 40 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 40
50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 50 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 3A
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC 60 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F 70 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F 9F
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 02 03 34 F1 50 61 90 22 20 05 04 03 02 01 5D 5E 0 02 03 30 F1 50 61 10 22 20 05 04 03 02 01 5D 5E
10 5F 66 62 63 64 23 09 57 07 6E 03 0C 00 20 00 B8 10 5F 66 62 63 64 23 09 57 07 6E 03 0C 00 30 00 B8
20 3C 20 00 80 01 02 03 04 67 D8 5D C4 01 78 80 03 20 3C 30 00 80 01 02 03 04 E3 0E 61 66 E3 06 07 01
30 E3 05 C0 00 E3 0F 01 10 E3 06 07 01 01 1D 80 18 30 01 1D 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00
40 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 66 21 40 00 9E 66 21 50 B0 51 00 1B 30 40 70 36 00 40 84
50 50 B0 51 00 1B 30 40 70 36 00 40 84 63 00 00 1E 50 63 00 00 1E 00 00 00 00 00 00 00 00 00 00 00 00
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 21 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 6C
# PCM HDMI2 (C/S: 9F,7C)_3G_UHD Deep Color OFF * Checksum (HDMI 1/2/3/4)
0 1 2 3 4 5 6 7 8 9 A B C D E F
2D ONLY PCM
0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 01 1A 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 3G 6G
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
HDMI1 0x9F, 0x8C 0x9F, 0x31
30 01 01 01 01 01 01 08 E8 00 30 F2 70 5A 80 B0 58
40 8A 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D 40 HDMI2 0x9F, 0x7C 0x9F, 0x21
50 58 2C 45 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
HDMI3 0x9F, 0x6C 0x9F, 0x11
60 3E 1E 88 3C 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 9F
0 1 2 3 4 5 6 7 8 9 A B C D E F 2D ONLY AC3
0 02 03 30 F1 50 61 10 22 20 05 04 03 02 01 5D 5E
10 5F 66 62 63 64 23 09 57 07 6E 03 0C 00 20 00 B8 3G 6G
20 3C 20 00 80 01 02 03 04 E3 0E 61 66 E3 06 07 01 HDMI1 0x9F, 0x1A 0x9F, 0xBF
30 01 1D 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00
40 00 9E 66 21 50 B0 51 00 1B 30 40 70 36 00 40 84 HDMI2 0x9F, 0x0A 0x9F, 0xAF
50 63 00 00 1E 00 00 00 00 00 00 00 00 00 00 00 00 HDMI3 0x9F, 0xFA 0x9F, 0x9F
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 7C
2D ONLY DTS
3G 6G
HDMI1 0x9F, 0x11 0x9F, 0XB6
HDMI2 0x9F, 0x01 0x9F, 0XA6
HDMI3 0x9F, 0xF1 0x9F, 0x96
5.3. Camera Port Inspection 5.4.4. Adj. Command (Protocol)
(1) Objective : To check how it connects between Camera and <Command Format>
PCBA normally, and their Function CMD ID DATA CR RF
(2) Test Method : This Inspection is available only Power-Only
Status. - CMD: Command
1) Push Camera Up - ID : Command
2) Cameras Preview picture appears on TV Set - Data : Command
3) Push Camera Down (Ex) [Send: va 00 00\r\n]
(1) RS-232C Command used during auto-adj.

RS-232C COMMAND
Explanation
CMD DATA ID
va 00 00 V-com pattern
vb 00 00 ~ FE V-com adj.(internal Flicker pattern)
wb 00 FF V-com adj. completed
(3) RS-232C Command
5.4.5. Adjustment method
RS-232C COMMAND
Explanation (1) Set TV in POWER-ONLY mode using POWER ONLY key
CMD DATA ID (2) Zero calibrate probe then place it on the center of the
Ai 00 23 Camera Function Start. Display
(3) Connect Cable (RS-232C to USB)
Ai 00 24 Camera Function End.
(4) Select Model in V-com adj. Program and begin V-com
adj.
5.4. V-COM Adjust (5) When V-com adj. is complete (OK)
(ONLY FOR EPI model, 43/49/55UH6600, 43/49/55UH6500) (6) Remove probe and RS-232C to USB cable to complete adj.
5.4.1. Overview V-com Adj. must begin as start command va 00 00 , and
V-COM adj. Objective & How-it-works finish as end command wb 00 ff
- Objective: To reduce each Panels V-COM voltage deviation
- How-it-works: When V-COM gain in the adjust-OSD of each V-com adjust data
SET is at default value, each SET can have flicker by each 43 inch 49 inch 55 inch 65 inch
Panels V-COM voltage deviation. In order to prevent flicker
V-com Data
of each SET, find the desired each Panels V-COM voltage
value. hex dec hex dec hex dec hex dec
- Adj. condition: normal temperature Max B4 180 8B 139 85 133 AB 171
1) Surrounding Temperature: 25 C 5 C
2) Warm-up time: About 5 Min Default 96 150 6D 109 68 104 8D 141
3) Surrounding Humidity: 20% ~ 80% Min 78 120 4F 79 49 73 6F 111
5.4.2. Equipment
(1) Color Analyzer: CA-310 (LED Module : CH 14) or CM-H505 5.4.5.1 Manual adj. method
(2) A dj. Computer (During auto adj., RS-232C protocol is TBD
needed)
(3) Adjust Remocon
(4) Signal : internal flicker Pattern in SET
Color Analyzer Matrix should be calibrated using CS-100
5.4.3. Equipment connection MAP

Co lo r Analyzer
Probe RS -232C
Co m p ut er
RS -232C
RS -232C
Pat t ern Generat o r

Signal Source
* If TV internal pattern is used, not needed
5.5. White Balance Adjustment (Ex) wb 00 00 -> Begin white balance auto-adj.
wb 00 10 -> Gain adj.
5.5.1. Overview
ja 00 ff -> Adj. data
5.5.1.1. W/B adj. Objective & How-it-works
jb 00 c0
(1) Objective: To reduce each Panels W/B deviation
...
(2) How-it-works: When R/G/B gain in the OSD is at 192, it
...
means the panel is at its Full Dynamic Range. In order to
wb 00 1f -> Gain adj. complete
prevent saturation of Full Dynamic range and data, one of
* (wb 00 20(start), wb 00 2f(endc)) -> Off-set adj.
R/G/B is fixed at 192, and the other two is lowered to find
wb 00 ff -> End white balance auto adj.
the desired value.
(3) Adj. condition: normal temperature
- Surrounding Temperature: 255 C
(2) Adjustment Map
- Warm-up time: About 5 Min
Applied Model : ALL MODELS
- Surrounding Humidity: 20% ~ 80%
Adj. Command Data Range Default
5.5.2. Equipment item (lower caseASCII) (Hex.) (Decimal)
(1) C olor Analyzer: CA-210 (LED Module : CH 14) CMD1 CMD2 MIN MAX
(2) A dj. Computer (During auto adj., RS-232C protocol is
Cool R Gain j g 00 C0 TBD
needed)
(3) Adjust Remocon G Gain j h 00 C0 TBD
(4) V ideo Signal Generator MSPG-925F 720p/204-Gray
B Gain j i 00 C0 TBD
(Model: 217, Pattern: 49)
Color Analyzer Matrix should be calibrated using CS-1000 R Cut TBD
G Cut TBD
5.5.3. Equipment connection MAP B Cut TBD
Co lo r Analyzer Medium R Gain j a 00 C0 TBD
Probe RS -232C G Gain j b 00 C0 TBD

Co m p ut er B Gain j c 00 C0 TBD
RS -232C R Cut TBD
RS -232C
Pat t ern Generat o r G Cut TBD

Signal Source B Cut TBD
* If TV internal pattern is used, not needed Warm R Gain j d 00 C0 TBD
G Gain j e 00 C0 TBD
B Gain j f 00 C0 TBD
5.5.4. Adj. Command (Protocol)
<Command Format> R Cut TBD
START 6E A 50 A LEN A 03 A CMD A 00 A VAL A CS A STOP G Cut TBD
- LEN: Number of Data Byte to be sent 5.5.5. Adjustment method

- CMD : Command 5.5.5.1. Auto WB calibration
- VAL : FOS Data value (1) Set TV in adj. mode using POWER ONNY key
- CS : Checksum of sent data (2) Zero calibrate probe then place it on the center of the
- A : Acknowledge Display
(Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX] (3) Connect Cable (RS-232C to USB)
(4) Select mode in adj. Program and begin adj.
(1) RS-232C Command used during auto-adj. (5) When adj. is complete (OK Sign), check adj. status pre
RS-232C COMMAND mode(Warm, Medium, Cool)
Explanation (6) Remove probe and RS-232C to USB cable to complete adj.
CMD DATA ID
W/B Adj. must begin as start command wb 00 00 , and
wb 00 00 Begin White Balance adj. finish as end command wb 00 ff, and Adj. offset if need
wb 00 10 Gain adj.(internal white pattern)
wb 00 1f Gain adj. completed
wb 00 20 Offset adj.(internal white pattern)
wb 00 2f Offset adj. completed
wb 00 ff End White Balance adj.
(internal pattern disappears )
5.5.5.2. Manual adj. method 5.5.7. EDGE & IOL LED White balance table
(1) Set TV in Adj. mode using POWER ON Edge & ALEF LED module change color coordinate because
(2) Zero Calibrate the probe of Color Analyzer, then place it on of aging time
the center of LCD module within 10cm of the surface.. apply under the color coordinate table, for compensated
(3) Press ADJ key -> EZ adjust using adj. R/C -> 7. White- aging time
Balance then press the cursor to the right (KEY).
( When KEY() is pressed 216 Gray internal pattern will be Luminance: 204 Gray, 80IRE
displayed) ** Except Gumi winter season(Jan~Feb) and except for winter
(4) One of R Gain / G Gain / B Gain should be fixed at 192, season (Mar ~ Dec) & Global are same as the table below
and the rest will be lowered to meet the desired value. S tandard color coordinate and temperature using
(5) Adj. is performed in COOL, MEDIUM, WARM 3 modes of CA-210(CH-14) by aging time
color temperature.
Cool Medium Warm
Aging time
** R-fix adjustment X Y X Y X Y
(Min)
Adjust modes (Cool), Fix the R gain to 210 (default data) and 271 270 286 289 313 329
change the others (G/B Gain ).
1 0-2 282 289 297 308 324 348
- Adjust the R gain more than 210 ( If G gain or B gain is less
than 0 , R gain can adjust more than 210 ) and change the 2 3-5 281 287 296 306 323 346
others ( G/B Gain ). 3 6-9 279 284 294 303 321 343
- Adjust two modes (Medium / Warm), Fix the one of R/G/B
gain to 192 (default data) and decrease the others. 4 10-19 277 280 292 299 319 339
5 20-35 275 277 290 296 317 336
If internal pattern is not available, use RF input. In EZ Adj. 6 36-49 274 274 289 293 316 333
menu 7.White Balance, you can select one of 2 Test-pattern:
ON, OFF. Default is inner(ON). By selecting OFF, you can 7 50-79 273 272 288 291 315 331
adjust using RF signal in 216 Gray pattern. 8 80-119 272 271 287 290 314 330
Adj. condition and cautionary items 9 Over 120 271 270 286 289 313 329
(1) Lighting condition in surrounding area
Surrounding lighting should be lower 10 lux. Try to isolate * Use only AUO, INX, Sharp, CSOT, BOE
adj. area into dark surrounding. (Cool temp Spec is 13000K)
(2) Probe location
- LCD : Color Analyzer (CA-210) probe should be within cool med warm
10cm and perpendicular of the module surface x y x y x y
(80~ 100)
(3) Aging time spec 271 270 286 289 313 329
- After Aging Start, Keep the Power ON status during 5 target 278 280 293 299 320 339
Minutes.
- In case of LCD, Back-light on should be checked using no
signal or Full-white pattern.
5.6. Local Dimming Function Check
(Step 1) Turn on TV
(Step 2) At the Local Dimming mode, module Edge Backlight
5.5.6. Reference (White Balance Adj. coordinate and moving right to left
color temperature) Back light of IOP module moving
Luminance: 206 Gray (Step 3) confirm the Local Dimming mode
Standard color coordinate and temperature using CS-1000 (Step 4) Press exit Key
(over 26 inch)
Coordinate
Mode Temp uv
X Y
Cool 0.271 0.270 13,000K 0.0000
Medium 0.283 0.289 9,300K 0.0000
Warm 0.313 0.329 6,500K 0.0000
Standard color coordinate and temperature using CA-210

(CH 14)
Coordinate
Mode Temp uv
X Y
Cool 0.2710.002 0.2700.002 13000K 0.0000
Medium 0.2860.002 0.2890.002 9300K 0.0000
Warm 0.3130.002 0.3290.002 6500K 0.0000
5.7. Magic Motion Remocon test 5.9 HDMI ARC Function Inspection
- Equipment : RF Remocon for test, IR-KEY-Code Remocon 5.9.1. Test equipment
for test - Optic Receiver Speaker
- You must confirm the battery power of RF-Remocon before - MSHG-600 (SW: 1220 )
test - HDMI Cable (for 1.4 version)
(recommend that change the battery per every lot)
- Sequence (test) 5.9.2. Test method
a) if you select the start key(OK) on the controller, you can (1) Insert the HDMI Cable to the HDMI ARC port from the
pairing with the TV SET. master equipment (HDMI2)
b) You can check the cursor on the TV Screen, when select (2) Check the sound from the TV Set
the OK Key on the controller
c) You must remove the pairing with the TV Set by select
Mute + OK Key on the controller
5.8. 3D function test

(Pattern Generator MSHG-600, MSPG-6100 [SUPPORT
HDMI1.4])
* HDMI mode NO. 872 , pattern No.83
(1) Please input 3D test pattern like below (HDMI mode NO. (3) Check the Sound from the Speaker or using AV & Optic
872 , pattern No.83) TEST program (Its connected to MSHG-600)
5.10. EYE-Q Green Function Inspection

(Step 1) Turn on the TV.
(Step 2) P ress 'EYE button' on the adjustment remote-
controller.
(Step 3) Cover 'Eye Q sensor' on the front of set with your
hands, hold it for 6 seconds.
(Step 4) Check "the Sensor Data" on the screen, make certain
that Data is below 10. If Data isnt below 10 in 6
seconds, Eye Q sensor would be bad. You should
change Eye Q sensor.
(Step 5) Uncover your hands from Eye Q sensor, hold it for 6
(2) When 3D OSD appear automatically , then select green seconds.
button (Step 6) Check "Back Light(xxx)" on the screen, check data
increase . You should change Eye Q sensor
(3) Dont wear a 3D Glasses, Check the picture like below
5.11. Ship-out mode check (In-stop)

After final inspection, press In-Stop key of the Adj. R/C and
check that the unit goes to Stand-by mode.
6. GND and Internal Pressure check 8. USB S/W Download
6.1. Method (optional, Service only)
(1) GND & Internal Pressure auto-check preparation (1) Put the USB Stick to the USB socket
- Check that Power Cord is fully inserted to the SET. (If (2) Automatically detecting update file in USB Stick
loose, re-insert) - If your downloaded program version in USB Stick is lower
(2) Perform GND & Internal Pressure auto-check than that of TV set, it didnt work. Otherwise USB data is
- Unit fully inserted Power cord, Antenna cable and A/V automatically detected.
arrive to the auto-check process. (3) Show the message Copying files from memory
- Connect D-terminal to AV JACK TESTER
- Auto CONTROLLER(GWS103-4) ON
- Perform GND TEST
- If NG, Buzzer will sound to inform the operator.
- If OK, changeover to I/P check automatically.
(Remove CORD, A/V form AV JACK BOX)
- Perform I/P test
- If NG, Buzzer will sound to inform the operator.
- If OK, Good lamp will lit up and the stopper will allow the
pallet to move on to next process. (4) Updating is staring
6.2. Checkpoint
(1) Test voltage
- GND: 1.5KV/min at 100mA
- SIGNAL: 3KV/min at 100mA
(2) TEST time: 1 second
(3) TEST POINT
- GND Test = POWER CORD GND and SIGNAL CABLE
GND.
- Hi-pot Test = POWER CORD GND and LIVE & NEUTRAL. (5) Updating Completed, The TV will restart automatically
(4) LEAKAGE CURRENT: At 0.5mArms
7. AUDIO output check

No Item Min Typ Max Unit Remark
1 Audio practical 10.0 12.0 W EQ Off
max Output, L/R 8.10 10.8 Vrms AVL Off
(Distortion=10% Clear Voice Off
max Output)
(6) If your TV is turned on, check your updated version and
2 Speaker 10 12 W EQ On Tool option.
(8 Impedance) AVL On * If downloading version is more high than your TV have, TV
Clear Voice On can lost all channel data. In this case, you have to channel
recover. If all channel data is cleared, you didnt have a DTV/
*Measurement condition: ATV test on production line.
(1) RF input: Mono, 1KHz sine wave signal, 100% Modulation
(2) CVBS, Component: 1KHz sine wave signal (0.4Vrms) * After downloading, TOOL OPTION setting is needed again.
(3) RGB PC: 1KHz sine wave signal (0.7Vrms) (1) Push "IN-START" key in service remote controller.
(2) Select "Tool Option 1" and Push OK button.
(3) Punch in the number. (Each model has their number.)
Copyright
DDR3 2133 X 32 X_TAL
(512MB X 2EA) 24MHz
(external)
EU ONLY
DDR3 1866 X 32 P_TS_IN

(128MB X 2EA) M1 M0 CI Slot

P_TS_OUT
(internal)
NVRAM (256Kb)
I2C 4
Vx1 51P (8 lane)
LG Electronics. Inc. All rights reserved.

Vx1 eMMC (4GB)
I2C 6
1. K2Lp Circuit Block Diagram
Realtek
K2Lp OCP USB1 (2.0)
MAIN Audio AMP I2S Out
I2C 4 HDMI1
- 26 -
(NTP7515)
HDMI2
HDMI3(ARC)
IF (+/-)
Block Diagram
IF
I2C_MICOM
Sub Micom (HW Port) P_TS_IN
X_TAL (RENESAS P_TS
32.768KHz R5F100GEAFB) I2C 2
USB_WIFI
SPDIF OUT
CVBS/YPbPr
ETHERNET
DEMOD
LNB (S2)
TUNER TUNER
(S2) (T2/C/A)
T2/C/S2 W/O AD
IR / KEY
MAX323
WIFI 11n only

DVB-S Air/
Cable
Sub Assy
OPTIC
LAN
REAR(H)
RS-232
AV/COMP
LGE Internal Use Only

Copyright
I2C_SCL6 I2C_SCL4 IC5800
P7100 33 B 3 [VSYNC] H2[GPIO_T_SCL]
Vx1 51P 34 I2C_SDA6 I2C_SDA4 100 NTP7515
B 2 [HSYNC] H1[GPIO_T_SDA] AMP
1.8k
1.8k
1.8k
1.8k

TCON_I2C_EN 33 IC101
NVRAM
+3.3V_NOR
+3.3V_NOR
Realtek
2. K2Lp I2C Block Diagram

K2Lp
- 27 -
I2C_SCL F10 [ST_IO09] I2C_SCL2 IC6901
IC3000 1 F13[ST_IO02] 7
R5F100GEAFB 33 I2C_SDA E10[ST_IO10] I2C_SDA2 33 A8303SESTR-T
2 E13[ST_IO03] 8
MICOM LNB
27 [SCL_DEMOD]
33
1.8 k
1.8 k
1.8k
1.8k
30 [SDA_DEMOD]
+3.3V_TU TU6701
+3.3V_NOR
TDJM-G301D
4 [SCL_RF]
33
5 [SDA_RF]
TU6700(TDJS-H301F): US

3. K2Lp Power Block
[UH61 Main]
3.5V ST-BY 4A
0.75A
13.2V (TI , TPS56428)
IC2306
2. 47A 0. 7A
SoC-K2L
1A
WIFI
0.18A 1.05V_CPU/GPU
4A(, RT7231
,IC2300) 0.17A
1.97A MICOM/IR/ETC
1.0V_CORE DC DC
0.51A 10A(TI, TPS51362 0.1A 1.0V ETH ST LDO
,IC2305)
5.68A
5.6 1A
0. 5A 1.5V DDR DC DC
0.98A 5V Normal 6A 3A(,BD9A300) 1A
(Rohm, RT7231) IC2303
IC2500
0.41A 3.3V Normal 2A

(,TJ2132) 1.41A
IC2301
0.02A
SOC
0.2A 1.8V eMMC

2A
0.6A 1.2V Tuner

2A TJ2132
0.4A TUNER
Panel
LNB(EU option)
13.2V Audio 20W 2ch
+3.3V_NORMAL
D_DEMOD_CORE
Copyright
+3.3V_TU
+2.5V_Normal
[+3.3V_LNA_TU] 1
[+3.3V_TUNER] 11
1.8K
[+3.3V_DEMOD_TU] 26
[+3.3V_1.2V_DEMOD] 28 33 7 [SCL]
[+2.5V_DEMOD] 38 8 [SDA]
LNB1
LNB_TX1 IC6901
[LNB_TX1] 29 10 [TONECTRL]
[LNB_OUT1] 31 LNB_OUT1 2 [LNB] A8303SESTR- TB
[I2C_SCL2_TU] 27
[I2C_SDA2_TU] 30 33

I2C_SCL2 AM5 [GPIO1_T_SCL]
[I2C_SCL5_TU] 4 I2C_SDA2 AM4 [GPIO2_T_SDA]
[I2C_SDA5_TU] 5 33
TDJM- G301D
K2Lp
4. Tuner/CI Block Diagram

RTK
[FE_DEMOD1_TS_ERROR] 12 FE_DEMOD2_TS_ERROR
FE_DEMOD1_TS_CLK AH6 [GPIO7_TPOCLK]
[FE_DEMOD1_TS_CLK_!] 14
FE_DEMOD1_TS_SYNC AH4 [GPIO10_TPOSYC]
[FE_DEMOD1_TS_SYNC_1] 15
FE_DEMOD1_TS_VAL AH5 [GPIO11_TPOVAL]
[FE_DEMOD1_TS_VAL_1] 16
FE_DEMOD1_TS_DATA [0- 7]
FE_DEMOD1_TS_DATA[0- 7] 17 - 24 AL4~AJ5 [GPIO*_TPOD0~TPDO7]
- 29 -
[FE_DEMOD2_TS_ERROR] 34
[FE_DEMOD2_TS_SYNC] 36 JAPAN_OPT
[FE_DEMOD2_TS_CLK]37
[FE_DEMOD2_TS_VAL] 39
FE_DEMOD2_TS_DATA [0]
[FE_DEMOD2_TS_DATA]40 JAPAN_OPT
[FE_DEMOD3_TS_ERROR] 41
[FE_DEMOD3_TS_SYNC] 42
[FE_DEMOD3_TS_CLK] 43
[FE_DEMOD3_TS_VAL] 44
[FE_DEMOD3_TS_DATA] 46
TU_JAPAN /TU_RESET2
[/TU_RESET2_TU] 45 AU38[GPIO80_SDD3]
/TU_RESET1
[/TU_RESET1_TU] 25 AN6[GPIO14_DIGI_MIC]
IF_P
[IF_P_TU] 6 AT2 [IF_P]
IF_N
[IF_N_TU] 7 AT3 [IF_N]
TUNER_SIF
[TU_SIF_TU] 9 OPT
TU_CVBS
[TU_CVBS_TU] 8 AG1 [VIN10P]
[IF_AGC_TU] 3 IF_AGC AM6[GPIO0_RF_IF_AGC1]

Jack Side SOC Side
Copyright
Realtek
K2Lp
COMP1_Y/CVBS

[VIN4P] E2
COMP1_Pb
[VIN3P] D2
COMP1_Pr
[VIN5P] E3
COMP1/AV1/DVI_L_IN

[AI1L] A4
COMP1/AV1/DVI_R_IN
[AI1R] B4
5. Video/Audio In Block Diagram
SPDIF OUT
- 30 -
SPDIF_OUT
[SPDIF_OUT] C5
IC6100
H/P JACK HP_L/ROUT_AMP HP_L/ROUT
AMP [HPOL/R] F4/F5
US Model use this jack

for SVC(RS-232C).

Copyright
AV/COMP

COMP1/AV1/DVI_L/R_IN AUD_SCK
[A4] AI1L GPIO90_SCLK [AM27] [38] CLK_I
[B4] AI1R AUD_LRCK SPK_L+ / L-
GPIO89_WCLK [AK28] [8] WCK
AUD_LRCH [30, 33] LPF
GPIO93_MCLK [AL27] [7] AUD_LRCH SPK L
GPIO1_T_SCL[H2] I2C_SDA4 / SCL4 MAIN AMP
[10,11]
GPIO2_T_SDA[H1] NTP7515
AMP_RESET_N

SPK_R+ / R-
[AI2R] [36] (IC5800)
6. Audio Out Block Diagram
[18, 21] LPF SPK R
Realtek
K2Lp
- 31 -
TU_SIF AMP_MUTE
[K1] IFP
22
MICOM
Tuner
27 US Model use this jack
for SVC(RS-232C).
SIDE_HP_MUTE
H/P AMP HP_L/ROUT_AMP

HPOL [F4] HP_L/ROUT TPA6138A2
HPOR [F5] LPF H/P Jack
(IC6100)
[D11] SPDIF_OUT [T4] GPIO17
HDMI_ARC
HDMI3
SPDIF_OUT
SPDIF

DDC 5V PULL- UP
Copyright
7. HDMI
HDMI_HPD_3
47k
ST_IO25_H2_SCL [G5]
ST_IO26_H2_SDA [E6] DDC_SCL1 / DDC_SDA1
CEC_REMOTE
TMDS1 - D0/D1/D2/CLK
P0

DDC 5V PULL- UP

47 k
ST_IO24_H1_HPD [F6] HDMI_HPD_2

ST_IO22_H1_SCL [C6] DDC_SCL2 / DDC_SDA2
Realtek CEC_REMOTE
ST_IO23_H1_SDA [B6]
K2Lp TMDS2 - D0/D1/D2/CLK
P1
- 32 -
DDC 5V PULL- UP
HDMI_ARC
HDMI_HPD_3
ST_IO21_H0_HPD [A7]
47 k
ST_IO19_H0_SCL [C7] DDC_SCL3 / DDC_SDA3

ST_IO20_H0_SDA [B7] CEC_REMOTE
TMDS3 - D0/D1/D2/CLK
P2
HPD/DDC
H0, H1 DDC
22
H2 MICOM
R5F100GEAFB
EEPROM
(IC3000)
BR24G02
(IC3301)
KOREA Model only support External. EEPROM

Copyright
TDP/TDN,RDP/RDN

LAN
8. USB / WIFI / UART
+3.5V_ST +3.5V_WOL
IC5201

WOL/ETH_POWER_ON
Switch IC
WOL_CTRL
+3.5V_ST
- 33 -
+3.5V_ST +3.5V_WIFI K2Lp
IC4102 MICOM
POWER ON
Switch IC
WIFI_EN
WOL/WIFI_POWER_ON
+3.5V_WIFI
WiFi WIFI_DP/DM

EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
400
900
120
800
521
121
540
350
530
LV1
700
A10
820
200
A2
IC101-*1
NVRAM +3.3V_NORMAL A0
BR24G256FJ-3
1 8
VCC
Clock for Main
A1 WP
2 7
A2 SCL
3 6
IN/OUT_1
GND SDA
IC101
4 5
8pF
FLOAT_1
XIN_MAIN
AT24C256C-SSHL-T C100 NVRAM_ROHM
C103
EAN61133501 0.1uF Write Protection
27.0MHz
2
1
- Low : Normal Operation
X101
A0 VCC
DEBUG_SOC_RESET_SW
1 8 - High : Write Protection SW100
NVRAM_ATMEL SOC_RESET_SW
PZ1608U121-2R0TF
JTP-1127WEM
4
FLOAT_2
A1 WP
IN/OUT_2
2 7 AR100 2 1
33 8pF
XOUT_MAIN
1/16W
A2
3 A0h 6
SCL C104 4 3
I2C_SCL4
L100
GND SDA I2C_SDA4
4 5
SOC_RESET_SW
+3.3V_NORMAL
IC100 IC100 IC100
LGE6551-CA1 LGE6551-CA1 LGE6551-CA1
R126
10K
HDMI detection port
R109
A13 A9 100 ACTIVE LOW RESET AF3
HDMI_HPD_CBUS_1 AK5 AL25
EPHY_TDN MDIN0 RST SOC_RESET CBUS_RX CAM_CD1_N GPIO18_PC_CD1_N GPIO73_SDCMD 5V_DET_HDMI_1
B13 AJ10 AM25
EPHY_TDP MDIP0 /PCM_CE1 GPIO29_PC_CE1_1_N GPIO74_SDCLK 5V_DET_HDMI_2
A12 F13 C8 AJ11 AL22
EPHY_RDN MDIN1 ST_IO02 I2C_SCL2 VOCEC 5V_HDMI_1 EB_OE_N GPIO31_PC_OE_N GPIO75-SDWP 5V_DET_HDMI_3
B12 E13 AL11 AM23
EPHY_RDP MDIP1 ST_IO03 I2C_SDA2 EB_BE_N1 GPIO32_PC_IORD_N GPIO76_SCCD TCON_I2C_EN
F12 H5 AK12 AM22
ST_IO04 LOCKOUT12 LOCKOUT12 MHL5V EB_BE_N0 GPIO34_PC_IOWR_N GPIO77_SDD0 BIT10
E12 AK19 AM24
ST_IO05 CAM_REG_N GPIO61_PC_REG_N GPIO78_SDD1 PWM_DIM
F11 AB1 AK17 AL24
ST_IO06 WOL/ETH_POWER_ON P0_BN D0-_HDMI1 PCM_RESET PWM_DIM2
E11 AC1 GPIO55_PC_RST GPIO79_SDD2
D0+_HDMI1 AL15 AL23
ST_IO07 PMIC_RESET P0_BP EB_WE_N GPIO43_PC_WE_N GPIO80_SDD3 /TU_RESET2
D11 port changed AA3 R143 0 AM17
ST_IO08 SPDIF_OUT P0_CKN CK-_HDMI1
A7 F10 (SPDIF noise issue) AB3 GPIO59_PC_INPACK_N
HDMI_HPD_3 I2C_SCL1 CK+_HDMI1 AK18
ST_IO21_H0_HPD ST_IO09 P0_CKP CAM_WAIT_N GPIO57_PC_WAIT_N
C7 E10 AD1
DDC_SCL_3 ST_IO19_H0_SCL ST_IO10 I2C_SDA1 P0_GN D1-_HDMI1
B7 PMIC_RESET AD2
DDC_SDA_3 D1+_HDMI1 AK22
ST_IO20_H0_SDA P0_GP GPIO81 BIT3
AE1 AJ22
ST_IO11 for POL_Test_En P0_RN D2-_HDMI1 EB_ADDR[0-14] BIT4
F9 AE2 GPIO82
ST_IO11 POL_TEST_EN P0_RP D2+_HDMI1
E9 EB_ADDR[0] AK20
ST_IO12 SOC_RX GPIO66_PC_A0
F6 D9 EB_ADDR[1] AM20
HDMI_HPD_2 ST_IO24_H1_HPD ST_IO13 SOC_TX SMARTCARD VCC
C6 F8 U1 GPIO64_PC_A1
D0-_HDMI2 EB_ADDR[2] AL18 AK23
DDC_SCL_2 ST_IO22_H1_SCL ST_IO14 AV1_CVBS_DET P1_BN GPIO62_PC_A2 GPIO83_SPI_WP PCM_5V_CTL
B6 E8 V1 EB_ADDR[3] AJ18 AJ24
DDC_SDA_2 ST_IO23_H1_SDA ST_IO15 SMARTCARD_PWR_SEL P1_BP D0+_HDMI2 SMARTCARD_DATA
F7 T3 GPIO60_PC_A3 GPIO86_SPI_DI0
EB_ADDR[4] AM19 AK25
ST_IO16 /USB_OCD3_0 USB_Control 2 P1_CKN CK-_HDMI2
GPIO58_PC_A4 GPIO87_SPI_CS_N SMARTCARD_RST
K2H HW Option G5
ST_IO17
E7
D7
USB_CTL3_0 P1_CKP
U3
W1
CK+_HDMI2 EB_ADDR[5]
EB_ADDR[6]
AJ17
AL17
GPIO56_PC_A5 GPIO84_SPI_HOLD
AJ23
AK24
CAM_IREQ_N
DDC_SCL_1 ST_IO25_H2_SCL ST_IO18 AV2_CVBS_DET P1_GN D1-_HDMI2 SMARTCARD_DET
E6 G4 W2 GPIO54_PC_A6 GPIO85_SPI_SCLK
DDC_SDA_1 D1+_HDMI2 EB_ADDR[7] AM16 AJ25
+3.3V_NORMAL ST_IO26_H2_SDA ST_IO30 COMP1_DET P1_GP GPIO52_PC_A7 GPIO88_SPI_DO0 SMARTCARD_CLK
+3.3V_NORMAL Y1 EB_ADDR[8] AM13
P1_RN D2-_HDMI2
B3 Y2 GPIO37_PC_A8 EMMC_DATA[0-7]
D2+_HDMI2 EB_ADDR[9] AJ12
DEBUB_RX ST_IO27_VGA_SCL AV2_CVBS_DET P1_RP GPIO35_PC_A9
A3
10K
DEBUG_TX EB_ADDR[10] AK11

ST_IO28_VGA_SDA GPIO30_PC_A10
R131
B9 EB_ADDR[11] AM12 AL8 AR101 EMMC_DATA[0]

MICOM_5KEY_JOG_TYPE LS0 HP_DET GPIO33_PC_A11 EMMC_D0 0
C9 M1 EB_ADDR[12] AK16 AM9 EMMC_DATA[1]
10K
10K
10K
10K
10K
10K
10K
10K
USB_Control 1 D0-_HDMI3
10K
10K
10K
BIT02_1
LS1 P2_BN
BIT06_1
BIT07_1
BIT08_1
BIT00_1
BIT01_1
BIT03_1
BIT04_1
BIT05_1
/USB_OCD1 GPIO50_PC_A12
BIT10_1
BIT09_1
A10 B8 N1 EMMC_D1
D0+_HDMI3 EB_ADDR[13] AJ13 AL9 EMMC_DATA[2]
RTC_XI LS2 USB_CTL1 P2_BP GPIO39_PC_A13 EMMC_D2
B10 L3 EB_ADDR[14] AM14 AL7 EMMC_DATA[3]
CK-_HDMI3
10K
RTC_XO P2_CKN GPIO41_PC_A14 EMMC_D3

M3
R104
R107
R117
R119
R121
R111
R113
R115
R125
R123
AM8
R101
CK+_HDMI3 EMMC_DATA[4]
R136
P2_CKP EMMC_D4
MICOM_KEY_ONE_KEY P1 AM7 EMMC_DATA[5]
P2_GN D1-_HDMI3
P2 EMMC_D5
BIT0 D1+_HDMI3 AL10 EMMC_DATA[6]
P2_GP EB_DATA[0-7] EMMC_D6
R1 AM10
BIT1 P2_RN D2-_HDMI3 EMMC_DATA[7]
R2 EMMC_D7
D2+_HDMI3 EB_DATA[0] AM21 AL6
P2_RP GPIO68_PC_D0 EMMC_DS EMMC_STRB
BIT2 IC100 EB_DATA[1] AK21 AL5
LGE6551-CA1 AA5 GPIO70_PC_D1 EMMC_CLK EMMC_CLK
EB_DATA[2] AL21 AM6
1/16W
BIT3 REXT GPIO72_PC_D2 EMMC_CMD EMMC_CMD
R155
6.2K
EB_DATA[3] AJ5 AM5
1%
BIT4 GPIO19_PC_D3 EMMC_RST_N EMMC_RST
USB_Control 1 EB_DATA[4] AJ6
TU_ExtDemod GPIO21_PC_D4
AM2 AG1 R129-*1 EB_DATA[5] AJ7
USB_DM1 XIN_MAIN 0 GPIO23_PC_D5 GPIO_89 for POL_Boot_Mode
BIT5 HSDM0 XIN AJ8 R5
AM1 AG2 EB_DATA[6]
JP104 USB_DP1 HSDP0 XOUT XOUT_MAIN GPIO25_PC_D6 GPIO15_AMP_I2C_SCL BIT1
EB_DATA[7] AJ9 T5
BIT6 C105 TU_ALL_IntDemod GPIO27_PC_D7 GPIO16_AMP_I2C_SDA BIT2
0.1uF R129 AM27
USB_Control 2 100 GPIO90_SCLK AUD_SCK
BIT7 AM3 IF_P IF_P_MAIN AK28
USB3_DM0 HSDM1 TU_ALL_IntDemod GPIO89_WCLK AUD_LRCK
AL3 K2 C107 AL27
USB3_DP0 HSDP1 IFN IF_N TPI_DATA[0-7] GPIO93_MCLK M_RFModule_RESET
BIT8 100pF AL28
K1
IFP IF_P GPIO92_D0 AUD_LRCH
TPI_DATA[0] AJ20 AK27
BIT9 C106 GPIO67_TP1_D0 GPIO91_D1 POL_EJTEG_EN
0.1uF R127 TU_ALL_IntDemod TPI_DATA[1] AL19
100 GPIO69_TP1_D1 GPIO91 for POL_EJTAG_En
BIT10 Closed to SOC IF_N IF_N_MAIN TPI_DATA[2] AJ21
C108 GPIO71_TP1_D2
TU_ALL_IntDemod TPI_DATA[3] AK6
R130 C111 100pF GPIO20_TP1_D3
J2 10K 100pF TPI_DATA[4] AK7
GPIO0_RF_IF_AGC1 IF_AGC TU_EXT_ATV IF FILTER GPIO22_TP1_D4
A17 H2 C109 TPI_DATA[5] AK8
WIFI_DM I2C_SCL4 1/16W GPIO24_TP1_D5
HSDM3 GPIO1_T_SCL 0.01uF Place Near to Main SoC AK9
A16 H1 5% TPI_DATA[6]
10K
10K
10K
10K
10K
10K
10K
10K
10K
10K
10K
WIFI_DP HSDP3 GPIO2_T_SDA I2C_SDA4 50V GPIO26_TP1_D6

AK10
BIT02_0
BIT00_0
BIT01_0
BIT10_0
must be pull-up TPI_DATA[7]

BIT07_0
BIT08_0
BIT09_0
BIT03_0
BIT04_0
BIT05_0
BIT06_0
POL_EJTAG_EN# POL_TEST_EN# GPIO28_TP1_D7

PLL_EN option pin POL_RBOOT_EN# 0x0h : Enable AM18
0x0h : Enable 0x0h : dont boot from Rom TPI_CLK GPIO53_TP1_CLK
AL1 L4 0x1h : Disable 0x1h : Disable AL20
0x1h : ROM boot
R110
TPI_VAL
R100
R112
R114
R116
R118
R120
USB3_RXM0 FE_DEMOD1_TS_DATA[0] GPIO63_TP1_VAL

R122
R124
R103
R106
HSIN GPIO9_TP0D0
DEBUG_T32_NON
AL2 L5 AJ19
USB3_RXP0 FE_DEMOD1_TS_DATA[1] +3.3V_NORMAL +3.3V_NORMAL +3.5V_ST TPI_SOP GPIO65_TP1_SYC
HSIP GPIO13_TP0D1
M4
R108 4.7K R105 4.7K
R173 4.7K R172 4.7K

GPIO12_TP0D2 FE_DEMOD1_TS_DATA[2]
C101 M5
R135 4.7K R134 1K

GPIO4_TPD3 FE_DEMOD1_TS_DATA[3]
0.1uF AJ3 N4 TPO_DATA[0-7]
USB3_TXM0 HSON GPIO3_TP0D4 FE_DEMOD1_TS_DATA[4]
AJ2 N5
USB3_TXP0 HSOP GPIO5_TP0D5 FE_DEMOD1_TS_DATA[5]
P4 POL_TEST_EN TPO_DATA[0] AK13 R4
C102 0.1uF POL_EJTEG_EN AUD_LRCK
20150307 version GPIO6_TPD6
P5
FE_DEMOD1_TS_DATA[6]
AL13
GPIO38_TPO_D0 GPIO14_DIGI_MIC
T4
/TU_RESET1
TPO_DATA[1] HDMI_ARC
GPIO8_TP0D7 FE_DEMOD1_TS_DATA[7] GPIO40_TPO_D1 GPIO17
J4 TPO_DATA[2] AK14
FE_DEMOD1_TS_CLK GPIO42_TPO_D2
OPT
OPT
BIT(0/1) DVB ATSC JP GPIO7_TP0CLK AM15
DEBUG_T32
K4 TPO_DATA[3]
GPIO10_TP0SYC FE_DEMOD1_TS_SYNC GPIO44_TPO_D3
J5 TPO_DATA[4] AJ14
00 TW/COL US GPIO11_TP0VAL FE_DEMOD1_TS_VAL GPIO45_TPO_D4
TPO_DATA[5] AJ15
GPIO47_TPO_D5
01 CN/HK KR JP TPO_DATA[6] AL16
+3.3V_NORMAL GPIO49_TPO_D6
Low High TPO_DATA[7] AJ16
10 EU BR GPIO51_TPO_D7
AL14
TPO_CLK
R158 1K
R161 1K
BIT4 Display LCD OLED GPIO48_TPO_CLK
11 AJJA CI AK15
TPO_VAL GPIO46_TPO_VAL
BIT5 15/16 Tuner 15_Tuner 16_Tuner AL12
TPO_SOP GPIO36_TPO_SYC
BIT(6/7/8) B/E(FRC) FLASH_TYPE_bit0
AUD_SCK
FLASH_TYPE_bit1
R159 4.7K
R162 4.7K
000 Vx1_60Hz_RGBW AUD_LRCH
BIT(2/3) EU/CIS AJJA TW/COL CN/HK KR North.AM BR JP Support
001 Vx1_60Hz_RGB EXTERNAL EDID
OPT
OPT
BIT9 EXTERNAL NON_EXTERNAL Boot FLASH_TYPE[1:0]
00 T2/C/S2 PIP_EX_ATV T_IN_ATV EXT_ATV IN_ATV Default
FOR HDMI2.0 0x0h : SPI
010 EPI_V16_RGBW
01 T2/C/S2_IN_ATV T2_IN_ATV ATSC+T2_IN_ATV 0x1h : SPI-NAND
T2/C/S2_IN_ATV IN_ATV BIT10 Division
011 EPI_V16_RGB NON_Division 4_Division 0x2h : NAND
0x3h: eMMC
10 T2/C/S2_EX_ATV T2/C/S2_EX_ATV ISDB_IN_ATV
100 EPI_V15_RGBW
DEBUG_T32
11 T2_EX_ATV AR1
101 EPI_V15_RGB
33
1/16W
TDI0 EB_BE_N1
RS232C_Debug RS232C_for DDTS +3.3V_TU_I2C +3.5V_WOL_ST +3.3V_NORMAL I2C PULL UP
GPIO PULL UP TDO0 EB_OE_N
TMS0 EB_BE_N0
TCK0 EB_ADDR[11]
+3.3V_NORMAL
+3.5V_ST DEBUG_UART_DDTS +3.5V_ST
OPT
P102 P100 P101 +3.3V_NORMAL
TU_NON_EU
TU_NON_EU
12525HS-04A(1.2T) 12507WS-04L 12507WS-04L

R132
10K
1.8K
10K
10K
10K
10K
10K
R168 OPT10K
R170 OPT10K
10K
R133
1.8K
R137
1.8K
R138
1.8K
R139
1.8K
R146
1.8K
R149
1.8K
R150
1.8K
OPT
10K
10K
OPT
OPT
OPT
OPT
VCC
JP109
C1
R156
1 1 1
R157
R163
R165
P1
0.1uF
R160
R164
R167
AR103 AR102 12505WS-10A00

100 100
TU_EU_1.2K
TU_EU_1.2K
DEBUG_T32
R102
R128
1/16W 1/16W DEBUG_T32

RESET TRST_N0
RX I2C_SDA6
R133-*1
1
EB_ADDR[10]
R132-*1
2 2 SOC_RX 2 DEBUB_RX I2C for LCD Module & EPI

I2C_SCL6 TDIO
2
TDI0
1.2K
1.2K
SOC_TX DEBUG_TX
TDO0
3
GND 3 3 I2C_SDA4 /TU_RESET1 3
TDO0
I2C for Main Amp / NVRAM TMS0
I2C_SCL4 AMP_RESET_N 4
TMS0
TCK0
4
TX 4 4
TCON_I2C_EN 5
TCK0
I2C_SDA1 /USB_OCD1 N.C
I2C for MICOM 6
I2C_SCL1 USB_CTL1
N.C
5 5 7
/USB_OCD3_0
3.3V
I2C_SDA2 USB_CTL3_0 8
I2C for tuner&LNB M_RFModule_RESET GND

I2C_SCL2 9
PCM_5V_CTL GND
10
11
@cirPi
Jtag I/F For Main
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS K2L 2015-01-08
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN1_SYSTEM 01
Copyright 2016 LG Electronics Inc. All rights reserved. LGE Internal Use Only
WOL&Instant ON
+3.5V_WOL_ST
+1.0V LDO Eth STDBY
IC200
AP7361-Y-13 ST_A1V0
OPT
L202
+3.5V_ST
R204
10K EN OUT
+3.5V_ST UBW2012-121F 1 5
Q204 WOL_CTL
SSM3J332R GND
2
D
S
ADJ/NC IN
3 4 C241
1A
ZD200
C248
2.5V
R208 10uF
G
10uF
30K C249 R205 10V
10V
10uF 5.1K R1
1%
10V
R206
20K
R209
1%
5.1K C231
10uF
10V R2
C
B Q203
INSTANT_BOOT MMBT3904(NXP) IC100 CPU_1V0
R207 D1V0 LGE6551-CA1
10K E
P19 A14 Vout=0.8*(1+R1/R2)=1.004V

CO1V0_1 CPU1V0_1
C202 C205 C208 C211 P20 A15 C218 C222 C224 C228
CO1V0_2 CPU1V0_2
C243 C200 0.1uF 0.1uF 0.1uF 0.1uF P21 B14 C215 0.1uF 0.1uF 0.1uF 0.1uF
CO1V0_3 CPU1V0_3 C245
10uF 10uF P22 B15 10uF 10uF
10V 10V CO1V0_4 CPU1V0_4 10V 10V
P23 C13
CO1V0_5 CPU1V0_5
AA14 C14
CO1V0_6 CPU1V0_6
AB14
AC14
CO1V0_7 CPU1V0_7
C15
D13
WOL switch
CO1V0_8 CPU1V0_8
AD14 D14 +3.5V_WOL
CO1V0_9 CPU1V0_9
AD15 D15
CO1V0_10 CPU1V0_10 OPT
DDR power for Instant ON AD16
AD17
CO1V0_11 CPU1V0_11
N16
N17
L206
CO1V0_12 CPU1V0_12
AD18 N18
+1.5V_DDR_INSTANTBOOT CO1V0_13 CPU1V0_13 +3.5V_ST UBW2012-121F
AD19 P16
AD20
CO1V0_14 CPU1V0_14
P17
Q202
OPT AD21
CO1V0_15 CPU1V0_15
P18
SSM3J332R
L203 C203 C206 C209 C212 C219 C223 C225 C229
CO1V0_16 CPU1V0_16
0.1uF 0.1uF 0.1uF 0.1uF AD22 0.1uF 0.1uF 0.1uF 0.1uF
D
C244 C201 C216
S
CO1V0_17 C246
+1.5V_DDR 10uF 10uF AD23 10uF 10uF
UBW2012-121F 10V 10V CO1V0_18 10V
AE26 10V C238
R202
Q206 CO1V0_19
G
AE27 10uF
30K C239
SSM3J332R AE28
CO1V0_20 10V
10uF
CO1V0_21
AE29 10V
D
S
CO1V0_22
AE30
CO1V0_23
R211 C250 R203
G
10uF 5.1K
30K C251
10V
10uF
10V C
B Q201
WOL_CTL MMBT3904(NXP)
R212
100 R201
10K E
C
B Q205 +3.5V_WOL_ST
DDR_CS_ON_OFF MMBT3904(NXP)
R210
BLM18PG121SN1D
10K E +3.5V_WOL
AF19
D3V3_1
AF20 C217 C220
L208
D3V3_2 0.1uF 0.1uF
AF21
D3V3_3
+3.3V_NORMAL
M10
BLM18PG121SN1D
A3V3_1
N10 C242
A3V3_2
P10 C221 C227 10uF
A3V3_3
L205
AE9 0.1uF 0.1uF 10V
A3V3_4
AE10
A3V3_5
AF8
A3V3_6
AF9
A3V3_7 +3.5V_WOL_ST
AF10
BLM18PG121SN1D
A3V3_8 C235
C233
10uF
D1V0 10V 0.1uF
L207
BLM18PG121SN1D
L200 A11
RTC3V3 PANEL_VCC
AF22 H10
LV1V0_1 STB3V3 +3.3V_NORMAL
C204 C207 C210 AF23
LV1V0_2 C234
10uF 0.1uF 0.1uF AF24 AB8
10V 16V 16V LV1V0_3 HDRX3V3_1 0.1uF
AB9 R200
HDRX3V3_2 10K
P14
GHA1V0 ST_A1V0
G
N14 L204
GHD1V0
R14 BLM18PG121SN1D
GHP1V0
S
C226 C230
D
C232
Y8 ST_A1V0 0.1uF 10uF
BLM18PG121SN1D
0.1uF C236 SSM3K324R

HDRX1V0_1 10V
Y9 10uF Q200 C237
HDRX1V0_2 10V 0.1uF
L201
AG16 16V
DVDD18_EMMC
EMMC1V8
C214 HDMI Power 3.3V separate

C213 0.1uF
0.1uF

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. K2L POWER 02
11/05/31
IC100
LGE6551-CA1 DDR_HYNIX DDR_HYNIX
IC401 IC403 M0_1_DDR_VREFCA
M0_DDR_VREFCA
G28
H5TQ4G63CFR-TEC H5TQ4G63CFR-TEC
M0_DDR_A0 M0_DDR_CKE
DC1_A0
J31 M0_1_DDR_VREFDQ
M0_DDR_A1 DC1_A1 R426 DDR3 DDR3
F30 M0_DDR_VREFDQ
M0_DDR_A2 DC1_A2 1K N3 4Gbit M8 N3
4Gbit M8
E28 M0_DDR_A0 A0 VREFCA M0_DDR_A0 A0 VREFCA
M0_DDR_A3
L28
DC1_A3 +1.5V_DDR M0_DDR_A1
P7
A1
(x16) M0_DDR_A1
P7
A1 (x16)
M0_DDR_A4 DC1_A4 P3 P3
F27 M0_DDR_A2 A2 M0_DDR_A2 A2
M0_DDR_A5 DC1_A5 N2 H1 N2 H1
K27 M0_DDR_A3 A3 VREFDQ M0_DDR_A3 A3 VREFDQ
M0_DDR_A6 DC1_A6 P8 P8
F28 M0_DDR_A4 A4 M0_DDR_A4_1 A4
M0_DDR_A7 DC1_A7 P2 +1.5V_DDR P2 +1.5V_DDR
J28 M0_DDR_A5 A5 R439 M0_DDR_A5_1 A5 R443
M0_DDR_A8 DC1_A8 R8 L8 R8 L8
G31 M0_DDR_A6 A6 ZQ M0_DDR_A6 A6 ZQ
M0_DDR_A9 DC1_A9 R2 240 R2 240
M27 M0_DDR_A7 A7 1% M0_DDR_A7 A7 1%
M0_DDR_A10 DC1_A10 C404 C405 C407 T8 T8
H28 C443 C441 M0_DDR_A8 M0_DDR_A8
0.1uF 0.1uF 0.1uF A8 A8
M0_DDR_A11 DC1_A11 10uF 10uF 16V 16V 16V R3 B2 R3 B2
L27 10V 10V M0_DDR_A9 A9 VDD_1 M0_DDR_A9 A9 VDD_1
M0_DDR_A12 DC1_A12 L7 D9 L7 D9
G30 M0_DDR_A10 A10/AP VDD_2 M0_DDR_A10 A10/AP VDD_2
M0_DDR_A13 DC1_A13 R7 G7 R7 G7
J30 M0_DDR_A11 A11 VDD_3 M0_DDR_A11 A11 VDD_3
M0_DDR_A14 DC1_A14 N7 K2 N7 K2
L31 M0_DDR_A12 A12/BC VDD_4 M0_DDR_A12 A12/BC VDD_4
DC1_A15 T3 K8 T3 K8
Place M0 POWER PLANE M0_DDR_A13 A13 VDD_5 M0_DDR_A13 A13 VDD_5
T7 N1 T7 N1
K29 M0_DDR_A14 A14 VDD_6 M0_DDR_A14 A14 VDD_6
M0_DDR_A4_1 DC1_A4_EXT M7 N9 M7 N9
G27 NC_5 VDD_7 NC_5 VDD_7
M0_DDR_A5_1 DC1_A5_EXT +1.5V_DDR R1 R1
+1.5V_DDR +1.5V_DDR VDD_8 VDD_8
M2 R9 M2 R9
M0_DDR_BA0 BA0 VDD_9 M0_DDR_BA0 BA0 VDD_9
M0_DDR_VREFCA M0_1_DDR_VREFCA N8 N8
E27 M0_DDR_BA1 BA1 M0_DDR_BA1 BA1
M0_DDR_BA0 DC1_BA0 M3 M3
K30 M0_DDR_BA2 BA2 M0_DDR_BA2 BA2
M0_DDR_BA1 DC1_BA1 A1 A1
R409
R428
1K 1%
1K 1%
H27 VDDQ_1 VDDQ_1
M0_DDR_BA2 DC1_BA2 J7 A8 J7 A8
H30 M0_U_CLK CK VDDQ_2 M0_U_CLK CK VDDQ_2
M0_DDR_CASN DC1_CASN K7 C1 K7 C1
M28 M0_U_CLKN CK VDDQ_3 M0_U_CLKN CK VDDQ_3
M0_DDR_CKE DC1_CKE C432 C434 C436 K9 C9 K9 C9
M30 C444 C442 M0_DDR_CKE M0_DDR_CKE
0.1uF 0.1uF 0.1uF CKE VDDQ_4 CKE VDDQ_4
M0_CLK DC1_CLK 10uF 10uF 16V 16V 16V +1.5V_DDR D2 D2
1%
1%
L30 10V VDDQ_5 VDDQ_5
M0_CLKN DC1_CLKB C400 C402 10V L2 E9 L2 E9
R410
R429
M29 0.1uF 0.1uF M0_CS0_N CS VDDQ_6 M0_CS1_N CS VDDQ_6
M0_CS0_N DC1_CSN K1 F1 K1 F1
AD26 16V 16V M0_DDR_ODT ODT VDDQ_7 M0_DDR_ODT ODT VDDQ_7
1K
1K
M0_CS1_N DC1_CSN_1 R436 J3 H2 C412 0.1uF J3 H2 C416 0.1uF
E30 M0_DDR_RASN RAS VDDQ_8 M0_DDR_RASN RAS VDDQ_8
M0_DDR_ODT DC1_ODT 1K K3 H9 C413 0.1uF K3 H9 C417 0.1uF
J27 Place M0 POWER PLANE M0_DDR_CASN CAS VDDQ_9 M0_DDR_CASN CAS VDDQ_9
M0_DDR_RASN DC1_RASN L3 L3
F29 M0_DDR_WEN WE M0_DDR_WEN WE
M0_DDR_RESET_N DC1_RST J1 J1
H29 NC_1 NC_1
M0_DDR_WEN DC1_WEN T2 J9 T2 J9
M0_DDR_RESET_N RESET NC_2 M0_DDR_RESET_N RESET NC_2
L1 L1
U31 NC_3 NC_3
M0_DDR_DQ0 DC1_DQ0 L9 L9
P29 NC_4 NC_4
M0_DDR_DQ1 DC1_DQ1 F3 F3
U30 M0_DDR_DQS0 DQSL M0_DDR_DQS2 DQSL
M0_DDR_DQ2 DC1_DQ2 G3 G3
R30 M0_DDR_DQS_N0 DQSL M0_DDR_DQS_N2 DQSL
M0_DDR_DQ3 DC1_DQ3
T29
M0_DDR_DQ4 DC1_DQ4 C7 A9 C7 A9
P30 M0_DDR_DQS1 DQSU VSS_1 M0_DDR_DQS3 DQSU VSS_1
M0_DDR_DQ5 DC1_DQ5 B7 B3 B7 B3
T30 M0_DDR_DQS_N1 DQSU VSS_2 M0_DDR_DQS_N3 DQSU VSS_2
M0_DDR_DQ6 DC1_DQ6 +1.5V_DDR +1.5V_DDR E1 E1
R31 VSS_3 VSS_3
M0_DDR_DQ7 DC1_DQ7 M0_1_DDR_VREFDQ E7 G8 E7 G8
N28 M0_DDR_DM0 DML VSS_4 M0_DDR_DM2 DML VSS_4
M0_DDR_DQ8 DC1_DQ8 M0_DDR_VREFDQ D3 J2 D3 J2
U28 M0_DDR_DM1 DMU VSS_5 M0_DDR_DM3 DMU VSS_5
M0_DDR_DQ9 DC1_DQ9 J8 J8
N27 VSS_6 VSS_6
R407
R424
1K 1%
1K 1%
M0_DDR_DQ10 DC1_DQ10 E3 M1 E3 M1
U27 M0_DDR_DQ0 DQL0 VSS_7 M0_DDR_DQ16 DQL0 VSS_7
M0_DDR_DQ11 DC1_DQ11 F7 M9 F7 M9
P27 M0_DDR_DQ1 DQL1 VSS_8 M0_DDR_DQ17 DQL1 VSS_8
M0_DDR_DQ12 DC1_DQ12 F2 P1 F2 P1
T27 M0_DDR_DQ2 DQL2 VSS_9 M0_DDR_DQ18 DQL2 VSS_9
M0_DDR_DQ13 DC1_DQ13 F8 P9 F8 P9
P28 M0_DDR_DQ3 DQL3 VSS_10 M0_DDR_DQ19 DQL3 VSS_10
1%
1%
M0_DDR_DQ14 DC1_DQ14 H3 T1 H3 T1
T28 C401 C403 M0_DDR_DQ4 DQL4 VSS_11 M0_DDR_DQ20 DQL4 VSS_11
R408
R425
M0_DDR_DQ15 DC1_DQ15 H8 T9 H8 T9
AC31 0.1uF 0.1uF M0_DDR_DQ5 DQL5 VSS_12 M0_DDR_DQ21 DQL5 VSS_12
M0_DDR_DQ16 DC1_DQ16 16V 16V G2 G2
1K
1K
Y29 M0_DDR_DQ6 DQL6 M0_DDR_DQ22 DQL6
M0_DDR_DQ17 DC1_DQ17 H7 H7
AC30 M0_DDR_DQ7 DQL7 M0_DDR_DQ23 DQL7
M0_DDR_DQ18 DC1_DQ18 B1 B1
AA30 VSSQ_1 VSSQ_1
M0_DDR_DQ19 DC1_DQ19 D7 B9 D7 B9
AB29 M0_DDR_DQ8 DQU0 VSSQ_2 M0_DDR_DQ24 DQU0 VSSQ_2
M0_DDR_DQ20 DC1_DQ20 C3 D1 C3 D1
Y30 M0_DDR_DQ9 DQU1 VSSQ_3 M0_DDR_DQ25 DQU1 VSSQ_3
M0_DDR_DQ21 DC1_DQ21 C8 D8 C8 D8
AB30 M0_DDR_DQ10 DQU2 VSSQ_4 M0_DDR_DQ26 DQU2 VSSQ_4
M0_DDR_DQ22 DC1_DQ22 C2 E2 C2 E2
AA31 M0_DDR_DQ11 DQU3 VSSQ_5 M0_DDR_DQ27 DQU3 VSSQ_5
M0_DDR_DQ23 DC1_DQ23 A7 E8 A7 E8
W28 M0_DDR_DQ12 DQU4 VSSQ_6 M0_DDR_DQ28 DQU4 VSSQ_6
M0_DDR_DQ24 DC1_DQ24 A2 F9 A2 F9
AC28 M0_DDR_DQ13 DQU5 VSSQ_7 M0_DDR_DQ29 DQU5 VSSQ_7
M0_DDR_DQ25 DC1_DQ25 B8 G1 B8 G1
W27 0 R416 M0_DDR_DQ14 DQU6 VSSQ_8 M0_DDR_DQ30 DQU6 VSSQ_8
M0_DDR_DQ26 DC1_DQ26 M0_CLK M0_U_CLK A3 G9 A3 G9
AC27 M0_DDR_DQ15 DQU7 VSSQ_9 M0_DDR_DQ31 DQU7 VSSQ_9
M0_DDR_DQ27 DC1_DQ27 R417
Y27 0
M0_DDR_DQ28 DC1_DQ28 M0_CLKN M0_U_CLKN
AB27
M0_DDR_DQ29 DC1_DQ29
Y28 27 R420
M0_DDR_DQ30 DC1_DQ30 C431
AB28
M0_DDR_DQ31 DC1_DQ31 27 R421
0.1uF
V30 16V
M0_DDR_DQS0 DC1_DQS0
V29
M0_DDR_DQS_N0 DC1_DQS0B
R27
R28
AD30
AD29
AA27
AA28
N30
M0_DDR_DM0 DC1_DM0
U26
M0_DDR_DM1 DC1_DM1
W30
M0_DDR_DM2 DC1_DM2
AD27
M0_DDR_DM3 DC1_DM3
DDR_MICRON DDR_MICRON
IC401-*1 IC403-*1
VREF_M0 1% MT41K256M16LY-093:N MT41K256M16LY-093:N
R400 240 D30
DDR1_ZQ
D31 N3
A0 VREFCA
M8 N3
A0 VREFCA
M8
P7 P7
DC1_VREF P3
A1
P3
A1
A2 A2
N2 H1 N2 H1
A3 VREFDQ A3 VREFDQ
P8 P8
A4 A4
P2 P2
A5 A5
R8 L8 R8 L8
A6 ZQ A6 ZQ
R2 R2
A7 A7
A18 VREF_M1
T8
A8
T8
A8
DDR_1V5_1 1% R3
A9 VDD_1
B2 R3
A9 VDD_1
B2
A19 D28 240 R401 L7
A10/AP VDD_2
D9 L7
A10/AP VDD_2
D9
R7 G7 R7 G7
DDR_1V5_2 DDR2_ZQ A11 VDD_3 A11 VDD_3
B18 D27 N7
A12/BC VDD_4
K2 N7
A12/BC VDD_4
K2
T3 K8 T3 K8
DDR_1V5_3 DC2_VREF A13 VDD_5 A13 VDD_5
B19 VDD_6
N1
VDD_6
N1
M7 N9 M7 N9
DDR_1V5_4 NC_5 VDD_7 NC_5 VDD_7
C18 VDD_8
R1
VDD_8
R1
M2 R9 M2 R9
DDR_1V5_5 BA0 VDD_9 BA0 VDD_9
C19 N8
BA1
N8
BA1
M3 M3
DDR_1V5_6 BA2 BA2
D18 VDDQ_1
A1
VDDQ_1
A1
J7 A8 J7 A8
DDR_1V5_7 CK VDDQ_2 CK VDDQ_2
D19 K7
CK VDDQ_3
C1 K7
CK VDDQ_3
C1
K9 C9 K9 C9
+1.5V_DDR DDR_1V5_8 CKE VDDQ_4 CKE VDDQ_4
N19 VDDQ_5
D2
VDDQ_5
D2
L2 E9 L2 E9
DDR_1V5_9 CS VDDQ_6 CS VDDQ_6
N20 K1
ODT VDDQ_7
F1 K1
ODT VDDQ_7
F1
J3 H2 J3 H2
DDR_1V5_10 RAS VDDQ_8 RAS VDDQ_8
N21 K3
CAS VDDQ_9
H9 K3
CAS VDDQ_9
H9
L3 L3
DDR_1V5_11 WE WE
N22 NC_1
J1
NC_1
J1
T2 J9 T2 J9
DDR_1V5_12 RESET NC_2 RESET NC_2
N23 NC_3
L1
NC_3
L1
L9 L9
DDR_1V5_13 NC_4 NC_4
N24 F3
LDQS A14
T7 F3
LDQS A14
T7
G3 G3
DDR_1V5_14 LDQS LDQS
P24
C7 A9 C7 A9
DDR_1V5_15 UDQS VSS_1 UDQS VSS_1
R24 B7
UDQS VSS_2
B3 B7
UDQS VSS_2
B3
E1 E1
DDR_1V5_16 VSS_3 VSS_3
T24 E7
LDM VSS_4
G8 E7
LDM VSS_4
G8
D3 J2 D3 J2
DDR_1V5_17 UDM VSS_5 UDM VSS_5
U24 VSS_6
J8
VSS_6
J8
E3 M1 E3 M1
DDR_1V5_18 DQ0 VSS_7 DQ0 VSS_7
V24 F7
DQ1 VSS_8
M9 F7
DQ1 VSS_8
M9
F2 P1 F2 P1
W24 F8
DQ3 VSS_10
P9 F8
DQ3 VSS_10
P9
H3 T1 H3 T1
Y24 H8
DQ5 VSS_12
T9 H8
DQ5 VSS_12
T9
DDR_1V5_21 +1.5V_DDR G2
DQ6
G2
DQ6
H7 H7
DQ7 DQ7
B1 B1
VSSQ_1 VSSQ_1
D7 B9 D7 B9
DQ8 VSSQ_2 DQ8 VSSQ_2
C3 D1 C3 D1
C8 D8 C8 D8
C2 E2 C2 E2
A7 E8 A7 E8
A2 F9 A2 F9
B8 G1 B8 G1
A3 G9 A3 G9
C424 C425 C426 C427 C428 C429
+1.5V_DDR 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
+1.5V_DDR_INSTANTBOOT 16V 16V 16V 16V 16V 16V
OPT
R422 0
R423 0
Place Near SoC
0.1uF 16V
0.1uF 16V
OPT
120
120
1%
1%
C438
C440
R446
R450
M0_CS0_N M0_CS0_N
M0_CS1_N M0_CS1_N
120
120
1%
1%
R447
R451
+1.5V_DDR +1.5V_DDR
VREF_M0 VREF_M1
R402
R404
1K 1%
1K 1%
1%
1%
0.1uF
0.1uF
R403
R405
C418
C419
16V
16V
1K
1K

FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS 2015-04-27
K2L
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. K2L DDR 03
IC100
LGE6551-CA1 EPI Lane
For 41p location
B25 B29
TXDBN2_L LVDS_AAN LVDS_CAN TXDAN2_L
A25 A29
TXDBP2_L LVDS_AAP LVDS_CAP TXDAP2_L
B24 B28
TXDBN3_L LVDS_ABN LVDS_CBN TXDAN3_L
A24 A28
TXDBP3_L LVDS_ABP LVDS_CBP TXDAP3_L
B23 AJ30 GCLK_A
EPI Share Lane TXDBN4_L LVDS_ACN LVDS_CCN MCLK_A
A23 AJ29
TXDBP4_L L/D_VSYNC Level Shifter
For 51p location B22
LVDS_ACP LVDS_CCP
AK31
TXDBN5_L LVDS_ADN LVDS_CDN GCLK_A
A22 AK30
TXDBP5_L LVDS_ADP LVDS_CDP
B21 AL31 L/D_DO
TXDBN6_L LVDS_AEN LVDS_CEN
A21 AK29 L/D_CLK
TXDBP6_L LVDS_AEP LVDS_CEP VID_CPU
B20 AL30
TXDBN7_L LVDS_AFN LVDS_CFN DATA_FORMAT_1
A20 AL29
TXDBP7_L LVDS_AFP LVDS_CFP VID_CORE
AF28 AF31
LOCKAn
AF27
LVDS_BAN LVDS_DAN
AF30
AGP_CTRL Default Low Set!
HTPDAn LVDS_BAP LVDS_DAP
AG28 AF29
EO_A LVDS_BBN LVDS_DBN
AG27 AG30 TXDAN2_L
Level Shifter BIT0 LVDS_BBP LVDS_DBP
AH28 AG29 TXDAP2_L
GST_A LVDS_BCN LVDS_DCN
AH27 AH31 TXDAN3_L
BIT6 LVDS_BCP LVDS_DCP
AJ28 AH30 TXDAP3_L
EO_A DATA_FORMAT_0 LVDS_BDN LVDS_DDN
AJ27 AH29 TXDAN0_L
BIT5 LVDS_BDP LVDS_DDP
GST_A B27 B31 TXDAP0_L
TXDBN0_L LVDS_BEN LVDS_DEN TXDAN0_L
A27 A31 TXDAN1_L
MCLK_A TXDBP0_L LVDS_BEP LVDS_DEP TXDAP0_L
B26 B30 TXDAP1_L
TXDBN1_L LVDS_BFN LVDS_DFN TXDAN1_L
A26 A30
TXDBP1_L LVDS_BFP LVDS_DFP TXDAP1_L
EPI Share Lane

For 41p location EPI Lane
For 41p location
IC100
LGE6551-CA1
C1 A4
VINRP AI1L COMP1/AV1/DVI_L_IN
D1 B4 2.2uF C654
VINRN AI1R COMP1/AV1/DVI_R_IN
B1 A5 2.2uF C655
VINGP AI2L VX1_MSE
C2 B5
VINGN AI2R AMP_RESET_N
A1
VINBP
C3
VINBN
D4
AI4L BIT7
D5
AI4R BIT8
E4
AIO2L
B2 E5
I2C_SDA6 VSYNC AIO2R
A2 F4
I2C_SCL6 HSYNC HPOL HP_LOUT
F5
HPOR HP_ROUT Internal Analog Demod Test Point
G2
VDACOUT DTV/MNT_V_OUT
DTV/MNT_V_OUT
Close to Main chip 0.047uF C629 D2 G3

COMP1_Pb COMP1_PbP VIN3P FSW0
R610 100 COMP1_PbP 0.047uF C630 E2
COMP1_Y/CVBSP VIN4P
R611 100 0.047uF C631 E3 C5
C603 COMP1_PrP BIT9 port changed
C632 VIN5P SPDIF_OUT
5pF 0.047uF D3 (SPDIF noise issue)
COMP1_YPbPrN VINY0N
50V 0.047uF C633 F3
TU_CVBS VIN10P
0.047uF C634 F1 C4
COMP1_YPbPrN SC_CVBS_IN
C635 VIN13P MICBAIS
0.047uF F2
GND pattern should be C606 VINA0N
AB5 L600 PZ1608U121-2R0TF
connected with 75ohm reg 5pF
of Component Jack COMP1_Y/CVBS R612 100 COMP1_Y/CVBSP ADCG
50V
R613 100 AG5 L601 PZ1608U121-2R0TF
C604
5pF BBG
50V GND pattern should be C657
connected with 75ohm reg AF5 0.1uF
VCMBB 16V
COMP1_YPbPrN of SCART Jack
C656
COMP1_Pr COMP1_PrP 1uF
R614 100 SC_CVBS_IN
R615 100
C605
5pF
50V
COMP1_YPbPrN

FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS K2L 15/04/27
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN4_EXT_IN/OUTPUT 04
IC100
LGE6551-CA1
B11 W4
DGND_1 DGND_87
B16 W5
DGND_2 DGND_88
B17 W9
DGND_3 DGND_89
C10 W15
DGND_4 DGND_90
C11 W16
C12
DGND_5 DGND_91
W17
M700
DGND_6 DGND_92
D26 W18
DGND_7 DGND_93 MDS62110222
D29 W19
DGND_8 DGND_94
E26 W20
DGND_9 DGND_95
E29 W21
F26
DGND_10 DGND_96
W22
M701 M705
DGND_11 DGND_97
G26 W23
DGND_12 DGND_98 MDS62110222 MDS62110213
G29 W26
DGND_13 DGND_99
H3 W29
DGND_14 DGND_100
H4 W31
H26
DGND_15 DGND_101
Y3
M702 M706
DGND_16 DGND_102
J3 Y4
DGND_17 DGND_103 MDS62110222 MDS62110213
J26 Y5
DGND_18 DGND_104
J29 Y15
DGND_19 DGND_105
K3 Y16
K5
DGND_20 DGND_106
Y17
M707
DGND_21 DGND_107
K26 Y18
DGND_22 DGND_108 MDS62110213
K28 Y19
DGND_23 DGND_109
L26 Y20
DGND_24 DGND_110
L29 Y21
DGND_25 DGND_111
M2 Y22
M26
DGND_26 DGND_112
Y23
M708
DGND_27 DGND_113
N2 Y26
DGND_28 DGND_114 MDS62110237
N15 AA4
DGND_29 DGND_115
N26 AA15
DGND_30 DGND_116
N29 AA16
DGND_31 DGND_117
N31 AA17
2.2uF
DGND_32 DGND_118
C700
P3 AA18 M709
10V
DGND_33 DGND_119
P15 AA19
DGND_34 DGND_120 MDS62110213
P26 AA20
DGND_35 DGND_121
R3 AA21 TOOL_UH70
DGND_36 DGND_122
2.2uF
R15 AA22
C701
DGND_37 DGND_123
10V
R16 AA23
DGND_38 DGND_124
R17 AA26
DGND_39 DGND_125
R18 AA29
DGND_40 DGND_126 TOOL_UH70_NOT
R19 AB2
DGND_41 DGND_127
R20 AB4
DGND_42 DGND_128
R21 AB15
DGND_43 DGND_129
R22 AB16
DGND_44 DGND_130
R23 AB17
JP700
JP701
JP702
JP703
DGND_45 DGND_131
R26 AB18
DGND_46 DGND_132
R29 AB19
DGND_47 DGND_133
T15 AB20
DGND_48 DGND_134
T16 AB21
DGND_49 DGND_135
T17 AB22
DGND_50 DGND_136
T18 AB23
DGND_51 DGND_137
T19 AB26
DGND_52 DGND_138
T20 AC2
DGND_53 DGND_139
T21 AC3
DGND_54 DGND_140
T22 AC4
DGND_55 DGND_141
T23 AC15
DGND_56 DGND_142
T26 AC16
DGND_57 DGND_143
U2 AC17
DGND_58 DGND_144
U4 AC18
DGND_59 DGND_145
U5 AC19
DGND_60 DGND_146
U15 AC20
DGND_61 DGND_147
U16 AC21
DGND_62 DGND_148
U17 AC22
DGND_63 DGND_149
U18 AC23
DGND_64 DGND_150
U19 AC26
DGND_65 DGND_151
U20 AC29
DGND_66 DGND_152
U21 AD3
DGND_67 DGND_153
U22 AD4
DGND_68 DGND_154
U23 AD28
DGND_69 DGND_155
U29 AE3
DGND_70 DGND_156
V2 AE4
DGND_71 DGND_157
V4 AF4
DGND_72 DGND_158
V5 AG3
DGND_73 DGND_159
V15 AG4
DGND_74 DGND_160
V16 AH2
DGND_75 DGND_161
V17 AH3
DGND_76 DGND_162
V18 AH4
DGND_77 DGND_163
V19 AJ4
DGND_78 DGND_164
V20 AK2
DGND_79 DGND_165
V21 AK3
DGND_80 DGND_166
V22 AK4
DGND_81 DGND_167
V23 AL4
DGND_82 DGND_168
V26 AL26
DGND_83 DGND_169
V27 AM4
DGND_84 DGND_170
V28 AM11
DGND_85 DGND_171
W3 AM26
DGND_86 DGND_172

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. K2L_GND 07
CI Region * Option name of this page : CI_SLOT
(because of Hong Kong)
CI SLOT
+5V_CI_ON
CI_DATA[0-7]
CI_DATA[0-7]
CI_SLOT
C902
10uF
10V
EAG63217207
CI_SLOT_MOLD_FCI/SPG
/CI_CD1 JK900
10125901-015LF
CI_SLOT
R912 35 1
100 CI_DATA[3]
36 2
CI_DATA[4]
37 3
CI_DATA[5] R916
38 4 10K
TPI_DATA_CI[4] CI_DATA[6]
39 5
40 6
TPI_DATA_CI[6]
41 7 R914 33 CI_SLOT
TPI_DATA_CI[7] CI_ADDR[10] /PCM_CE1
42 8
CI_SLOT R908 10K 43 9
CI_ADDR[11] CI_OE
CI_IORD 44 10 +5V_NORMAL
CI_ADDR[9]
CI_IOWR 45 11
CI_ADDR[8]
46 12 R917
CI_ADDR[13] 10K
CI_MDI[0] 47 13
CI_ADDR[14]
CI_MDI[1] 48 14 CI_SLOT
CI_MDI[2] 49 15 CI_WE
50 16 R915 100
CI_MDI[3] CI_SLOT
CAM_IREQ_N
51 17 CI_SLOT
GND
C901
0.1uF
52
53
18
19
C903
0.1uF
C904
0.1uF
CI HOST I/F
CI_MDI[4] CI_SLOT CI_SLOT
GND
CI_MDI[5] 54 20
+5V_NORMAL CI_ADDR[12]
CI_MDI[6] 55 21
CI_ADDR[7]
R900 56 22 GND
CI_MDI[7] R909 10K CI_ADDR[6]
10K CI_SLOT 57 23
CI_SLOT CI_ADDR[5]
PCM_RESET_CI 58 24 CI_DATA[0] EB_DATA[0] CI_MDI[3] TPO_DATA[3]
CI_ADDR[4]
CAM_WAIT_N_CI 59 25 TPI_DATA_CI[1] TPI_DATA[1] CI_MDI[4] TPO_DATA[4]
CI_ADDR[3]
REG 60 26 CI_DATA[1] EB_DATA[1] CI_ADDR[12] EB_ADDR[12]
CI_ADDR[2]
TPI_CLK_CI 61 27 CI_DATA[2] EB_DATA[2] CI_MDI[6] TPO_DATA[6]
CI_ADDR[1] CI_SLOT
TPI_VAL_CI 62 28 CI_SLOT
CI_ADDR[0] 1/16W 1/16W
TPI_SOP_CI 63 29 33 33
CI_DATA[0]
64 30 AR902 AR911
TPI_DATA_CI[1] 65 31 CI_ADDR[0-14]
CI_DATA[2] CI_DATA[3] EB_DATA[3] CI_ADDR[6] EB_ADDR[6]
TPI_DATA_CI[2] 66 32
TPI_DATA_CI[3] TPI_DATA[3] CI_ADDR[5] EB_ADDR[5]
TPI_DATA_CI[3] 67 33
CI_DATA[4] EB_DATA[4] CAM_WAIT_N_CI CAM_WAIT_N
68 34
G2 69 G1 CI_SLOT CI_SLOT
R910 1/16W 1/16W
R901 33 CI_SLOT 33 33
PCM_RESET PCM_RESET_CI 100
/CI_CD2 AR903 AR910
CI_SLOT GND
CI_DATA[5] EB_DATA[5] CI_ADDR[14] EB_ADDR[14]
R903 33 CI_SLOT
TPI_CLK TPI_CLK_CI TPI_DATA_CI[5] TPI_DATA[5] CI_WE EB_WE_N
CI_SLOT GND
C900 CI_DATA[6] EB_DATA[6] TPO_DATA[1]
CI_MDI[1]
2pF
50V TPI_DATA_CI[6] TPI_DATA[6] CI_MDI[2] TPO_DATA[2]
CI_SLOT CI_SLOT
GND
1/16W 1/16W
33 33
AR905 AR908
CI_DATA[7] EB_DATA[7] CI_MISTRT TPO_SOP

CI_MISTRT
CI_MIVAL_ERR TPO_VAL CI_ADDR[13] EB_ADDR[13]
CI_MIVAL_ERR
CI_MDI[5] TPO_DATA[5] CI_MDI[0] TPO_DATA[0]
CI_SLOT CI_SLOT
CI_MCLKI 1/16W 1/16W
33 33
AR906 AR909
CI_MCLKI TPO_CLK CI_ADDR[10] EB_ADDR[10]

METAL CI SLOT ONLY FOR 43/49UH61 EAG63217210 CI_MDI[7] TPO_DATA[7] CI_OE EB_OE_N
CI_SLOT_METAL_43_49UH61_ONLY CI_SLOT_MOLD_HONGLIN CI_ADDR[7] EB_ADDR[7] CI_ADDR[11] EB_ADDR[11]
JK900-*2 JK900-*1
10067972-000LF HONGLIN... CI_ADDR[4] EB_ADDR[4] CI_ADDR[9] EB_ADDR[9]
CI_SLOT CI_SLOT
CI DETECT 1
EAG41860102
35 35 1
1/16W
33
AR904
1/16W
33
AR912
2 36 36 2
+5V_NORMAL 3 37 37 3
CI_ADDR[2] EB_ADDR[2] REG CAM_REG_N
4 38 38 4
TPI_VAL_CI TPI_VAL TPI_SOP_CI TPI_SOP
CI_SLOT 5 39 39 5
CI_SLOT R906 +3.3V_NORMAL CI_ADDR[1] EB_ADDR[1] CI_ADDR[0] EB_ADDR[0]
R907 10K CI_SLOT 6 40 40 6
IC900 TPI_DATA_CI[0] TPI_DATA[0] TPI_DATA_CI[2] TPI_DATA[2]
10K 74LVC1G32GW 7 41 41 7 CI_SLOT
CI_SLOT
B 1 5 VCC 8 42 42 8 1/16W 1/16W
/CI_CD2 33 33
A 2
9 43 43 9 AR907 AR901
/CI_CD1
10 44 44 10
GND 3 4 Y
CAM_CD1_N 11 45 45 11 AR900
33
12 46 46 12 1/16W
13 47 47 13
CI_IORD EB_BE_N1
14 48 48 14
CI_IOWR EB_BE_N0
15 49 49 15 CI_SLOT
16 50 50 16
17 51 51 17
18 52 52 18
19 53 53 19
20 54 54 20
21 55 55 21
CI POWER ENABLE CONTROL 22

23
56
57
56
57
22
23
24 58 58 24
25 59 59 25
26 60 60 26
IC901
+5V_NORMAL AP2151WG-7 27 61 61 27
+5V_CI_ON
28 62 62 28
29 63 63 29
IN OUT 30 64 64 30
CI_SLOT 5 1
C905 31 65 65 31
CI_SLOT
0.1uF C906 32 66 66 32
16V GND
2 1uF 33 67 67 33
CI_SLOT R923
10V
10K 34 68 68 34
R922 CI_SLOT
100 EN FLG CI_SLOT
PCM_5V_CTL 4 3 G1 69 G2 G2 69 G1
R921
10K
CI_SLOT

FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS K2L / K2Lp 2015-01-10
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. PCMCI 9
PCMCI
+1.5V DDR
+3.5V_ST
POWER_ON/OFF2_3
Power_DET
R2322
10K
OPT
C2335 +3.5V_ST
0.1uF NON_OLED
+13V +3.5V_ST
16V R2335
100K
C2338
PD_+12V PD_+3.5V PD_RESET_IC_APX803-MAIN
0.1uF R2331 R2333 R2336
0 IC2304 10K
14K
[EP]FIN
+1.5V_DDR 1% 5% APX803L OPT
16V
AVIN
BOOT
L2306
PGD
EN
VCC 3 2 RESET POWER_DET
NR5040T2R2N NON_OLED EAN61829903
L2309 1
C2356
16
15
14
13
2.2uH PD_RESET_IC_7529M2-SUB
PD_+12V 0.1uF IC2304-*1
PVIN_1 1 12 SW_3 GND
R2332 16V PD_RESET_IC
THERMAL 5.1K KIC7529M2
PVIN_2 SW_2 C2358
ZD2302
2 17 11
C2365
150uF
C2324 1%
2.5V
6.3V
C2366 0.1uF
OPT
10uF EAN62870501 C2348 C2350 C2354 C2361 C2326 C2328 VCC
0.1uF PGND_1 3 IC2303 10 SW_1 3 2 OUT 16V
10V 16V 10uF 10uF 10uF 10uF 10uF 10uF
BD9A300MUV EAN63491301
C2339 10V 10V 10V 10V 10V 10V 0 1 not to RESET
PGND_2 4 9 SS
R2341 at 8kV ESD
3A 0.01uF OPT
POWER_DET_1
GND
8
50V
1%
1/16W
16K
R2328
+3.5V_ST R1
AGND
FB
ITH
MODE
R2349
330K
R2326
OPT
330K
R2323
8.2K C2342
R2
1% 1/16W 50V 2700pF
3A
1%
1/16W
18K
R2329
Vout=0.8*(1+R1/R2)
+1.0V CORE
R2314
+3.3V - eMMC +3.3V_NORMAL
430K
1%
+3.5V_ST
FET_KEC
DEBUG_LED
R2317
2N7002KA
Q2300-*1
330K
+3.3V_NORMAL +1.8V
R2310
3.3V_EMMC DVDD18_EMMC
5%
POWER_ON/OFF2_2 G
VID_CORE Low : 0.970V
33
T2N7002AK S
VID_CORE High : 1.0V Q2300
FET_TOSHIBA
EAV60793101
DEBUG_LED
LD2300
C2346 D
L2304 L2305
1%
1/16W
47K
R2330
R2318 +13V
PZ1608U121-2R0TF PZ1608U121-2R0TF 0.1uF G
R2327
C2345 16V R1 VID_CORE
0.1uF 5% 0
1K
OPT BLM18PG121SN1D
16V S
C2308 C2307 R2324 +3.5V_ST
C2309 C2323 C2312 C2327 10K
1%
1/16W 1/16W
47K
R2338 R2337
0.1uF 0.1uF L2313
DEBUG_LED
10uF 10uF 10uF 10uF

R2315
1/16W
16V 16V
[EP]GND
10V 10V 10V 10V
5.6K
REFIN2
R2 IC2306
REFIN
R1
5%
VREF
5%
R2346
TPS56428DDAR [EP]GND
10K
EN
RA
0
C2360 C2363
1%
1/16W
240K
GSNS
R2340
10uF 0.1uF
C2353 25V
28
27
26
25
24
D1V0 EN
1 8
VIN 25V
PGOOD_1 1 23 GSNS debugging point 5pF
THERMAL
THERMAL R2339 50V
LP# 2 29 22 VSNS VFB VBST
9
2 7 VLS6045EXT-4R7M(125)
0 +3.5V_ST
+1.8V - K2L, eMMC MODE 3
IC2305
21 SLEW
C2347 +5V_NORMAL
R2
VREG5 SW
C2357
0.1uF
L2312
4.7uH
1%
1/16W
47K
NC TRIP 50V
R2344
C2344 R2321 4 20 0.01uF 3 6
& Vx1 pull-up D1V0 25V 4.7
BST 5
TPS51362RVER
19 GND
25V
4A
ZD2305
CMLB065T-1R0MS C2352 PG GND
R2345
1/16W
+1.8V C2368 C2370 C2369
5V
0.1uF 5% SW_1 V5 2.2uF 4 5 10V
3.6K
L2307 6 18 10uF 10uF 10uF 10uF
10V C2355
+3.3V_NORMAL
1%
1uH 10V 10V 10V
IC2301 SW_2 7 17 VIN_1 +13V 0.47uF C2367
25V
ZD2303 2.5V
C2325 10uF 10V
C2330 10uF 10V
C2332 10uF 10V
C2336 10uF 10V
C2340 10uF 10V

C2337 10uF 10V
TJ2132GDP [EP]GND SW_3 8 16 VIN_2

R2320
L2308
1/8W
R2308 R2 SW_4 VIN_3

3.3
OPT
10K 9 15
5%
1 8 1% C2349 C2351
Vout=0.6*(1+R1/R2)
10
11
12
13
14
10uF 10uF
THERMAL
POK GND OPT 25V 25V

R2307
R2309
PGND_5
PGND_4
PGND_3
PGND_2
PGND_1
10K C2343
9
2 7
20K
R1 470pF
1%
POWER_ON/OFF2_2 EN FB 50V
3 6
+5V_NORMAL OUT C2333 R2319
IN
0.01uF GSNS
C2310
10uF 4 2A 5 25V 0
10V SS OPT
ZD2304
BIAS C2341
Vout=2*R2/(R1+R2)=1.054V
2.5V
C2311 EAN63492001 10uF

1uF 10V
10V C2359
2700pF
50V
Vout=0.6*(1+R1/R2)=1.8V +1.05V_CPU_GPU K2L Power SEQUENCE
+13V
POWER_ON/OFF1(5V)
VID_CPU High : 1.03V
VID_CPU Low : 1.00V
+3.3V_NORMAL R1
L2302
PZ1608U121-2R0TF
POWER_ON/OFF2_1(3.3V)
+3.3V_NORMAL
C2313
C2318 C2319
IC2302 1uF 10uF 0.1uF
25V IC2300 25V 16V
L2300 MP1471AGJ-C667 OPT POWER_ON/OFF2_2(1.05V / 1.0V / 1.8V)
4.7uH R2347 RT7231GQW [EP]PGND
POWER_ON/OFF2_1 R2300
22 6.8K
GND BST 5% 1%
1 6 EN VIN_2
POWER_ON/OFF2_2 1 10
ZD2300
C2301 C2303 C2304 C2314

C2302
+13V
THERMAL
OPT R2343 POWER_ON/OFF2_3(1.5V)

5V
10uF 10uF 10uF SW EN R2342

R1 10uF
2 5 0.1uF 10K
11
10V 10V 10V 10V 16V FB VIN_1

2 9
10K
R2304 IN FB C2331 C2315
1.2K 3 4 0.1uF VREG5 BOOT CPU_1V0
R2301 3 8 POWER_ON/OFF2_4
1% L2301 16V 22K C2317 L2303 1.0uH
UBW2012-121F 1% 10V 1uF
R2305 OPT R2 C2316
0.1uF Epoxy-SDES053T-1R0MS
SS SW_2
R2325
7.5K 25V
4 7
1% R2302
1%
1/16W
75K
R2348
OPT OPT
ZD2301
2K
1%
0 50V 4700pF C2320 C2321 C2322 C2329

2.5V
C2300 R2311 C2305 C2306

10uF 5% PGOOD SW_1 10uF 10uF 10uF 10uF SOC_RESET
25V 0.1uF 5 6 10V 10V 10V 10V
20K
R2334
1500pF 50V +3.3V_NORMAL

180K
50V
1%
R2
R2303
1/16W
R2306 10K D FET_TOSHIBA

2.7K R2313 G Q2302
1% Vout=0.8*(1+R1/R2) VID_CPU
0 5%
T2N7002AK
D
S
2N7002KA
Q2302-*1
Vout=0.765*(1+R1/R2)
FET_KEC
G
S

FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS K2H 2015-01-10
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. PWR_1 07
PANEL_POWER
2N3906S-RTK
+3.5V_ST A13V
Q2302 Change: Diodes --> NXP, 131118
C2511
R2502
10uF +13V
25V
1
10K
R2500
GND
Q2500
RL_ON 10K P2502 PANEL_VCC

SMAW200-H18S5 Q2504
PSU_18P SSM3J332R
2
L2504
D
S
3
55INCH_BOE_M+_MODULE
D-GND D-GND R2507 100 UBW2012-121F
C2522
ADUC 20S 02 010L

PWM_DIM2 C2520 R2519
OPT
VA2500
G
P/ON PDIM2 +13V 0.1uF 36K 0.1uF
L2502 55/60/65INCH_LGD_M+_MODULE C2523 C2524
LVDS_DISCHARGE
+3.3V_NORMAL D-GND D13 50V 50V 10uF 10uF
R2506
R2521
D13 D13 MLB-201209-0120P-N2 0 LGD_M+_MODULE 25V 25V
3.3K
PSU_MODE_SELECT_NON A13V
R2501 L2503
A13 A13 PWM_TCON_OUT
1K PSU_MODE_SELECT_NON R2508 100
A-GND A-GND MLB-201209-0120P-N2
100 R2503 BOE_M+_MODULE R2520
INV_CTL INVON PDIM1 PWM_DIM 150K
GND SCLK R2509 100
MODE_SELECT L/D_CLK
L/D_VSYNC VSINC SIN R2512 100 L/D_DO C
R2514 100 R2513 100
B Q2503
PANEL_CTL MMBT3904(NXP)
P2501
SMAW200-H12S5K(BK)(LTR) R2518
PSU_12P +13V 10K E
C2521
10K
R2517
4.7uF
C2508 C2512 10V
C2505 10uF 10uF
JP2505 0.1uF OPT
+13V JP-BLOCK-1POWER_13V 25V 25V
25V
D13V
GND
15 UHD 12.5V sole out power

Net name +12V means 12.5V power output
+5.0V normal & USB

+13V
L2500
PZ1608U121-2R0TF
R1
POWER_ON/OFF1 C2504 C2506

10uF 0.1uF
IC2500 25V 16V
OPT
RT7231GQW [EP]PGND
R2504 C2516
12K 150pF
1% 50V EN VIN_2
1 10
C2500
THERMAL
OPT R2511
0.1uF 10K
11
16V FB VIN_1
2 9
C2501
VREG5 BOOT +5V_NORMAL
R2505 3 8
1.6K C2503 L2501
1% 10V 1uF SPM6530T-3R3M
R2 C2502
0.1uF
3.3uH
SS SW_2 25V
4 7
R2510
ZD2500
560 50V 4700pF C2509 C2513 C2514 C2515

5V
1% PGOOD SW_1 10uF 10uF 10uF 10uF

5 6 10V 10V 10V 10V
Vout=0.765*(1+R1/R2)

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. PWR_2 08
Renesas MICOM
MICOM_MODE_SELECT
R3000
10K
MODE_SELECT(PWM1) MODE_SELECT
For Debug
C3005
2.2uF
+3.5V_ST
10V
MICOM_MODE_SELECT
MICOM_DEBUG
R3016 1K
R3014 10K
MICOM_DEBUG Dont remove R3016,

P3000
12507WS-04L
not making float P40 50V 50V
18pF 15pF
C3002 C3003
MICOM_RESET
MICOM_DEBUG
1
2
MICOM_DEBUG
X3000
WIFI_EN
3
LED_R
4
MICOM_RESET 32.768KHz +3.5V_ST
5 R3028
4.7M
RETENTION_DISABLE
OPT
10K
POWER_DET_1
MICOM_LCD
R3030
T_CON_SYS_POWER_OFF MICOM_RESET_SW
GND
R3039
1/16W
SW3000
10K
T_CON_SYS_POWER_OFF JTP-1127WEM
5%
2 1
33
R3031
270K
OPT
C3004
P124/XT2/EXCLKS
0.47uF
0.1uF
+3.5V_ST 4 3
16V
R3029
P122/X2/EXCLK
P41/TI07/TO07
C3001
P137/INTP0
P120/ANI19
P40/TOOL0
P123/XT1
C3000
P121/X1
0.1uF
RESET
REGC
VDD
VSS
K2L Power SEQUENCE
48
47
46
45
44
43
42
41
40
39
38
37
POWER_ON/OFF1(5V) AR3001
33
1/16W P60/SCLA0 1 36 P140/PCLBUZ0/INTP6 RL_ON
I2C_SCL1
POWER_ON/OFF2_1(3.3V) P61/SDAA0 2 35 P00/TI00/TXD1 INSTANT_BOOT

RETENTION_DISABLE
I2C_SDA1
P62 3 34 P01/TO00/RXD1
3D&L_DIM_EN POWER_ON/OFF2_4 POWER_ON/OFF2_4
P63 4 33 P130
POWER_ON/OFF2_2(1.05V / 1.0V / 1.8V) INV_CTL
P31/TI03/TO03/INTP4 IC3000 P20/ANI0/AVREFP
POWER_ON/OFF2_1
MODE_SELECT(PWM1) 5 32 KEY2
IR
P75/KR5/INTP9/SCK01/SCL01 6 R5F100GEAFB#30 31 P21/ANI1/AVREFM
KEY1
POWER_ON/OFF2_3(1.5V) R3038
P74/KR4/INTP8/SI01/SDA01 P22/ANI2
HDMI_CEC
100
7 30 MODEL1_OPT_0(AM0)
POWER_ON/OFF2_2
P73/KR3/SO01 8 29 P23/ANI3
MODEL1_OPT_1(AM1)
POWER_ON/OFF2_4
POWER_ON/OFF2_3
P72/KR2/SO21 9 28 P24/ANI4 MODEL1_OPT_2(AM2)
P71/KR1/SI21/SDA21 10 27 P25/ANI5
EYE_SDA MODEL1_OPT_3(AM3)
SOC_RESET P70/KR0/SCK21/SCL21 P26/ANI6
EYE_SCL 11 26 SIDE_HP_MUTE
P30/INTP3/RTC1HZ/SCK11/SCL11 12 25 P27/ANI7
WOL/WIFI_POWER_ON DDR_CS_ON_OFF
13
14
15
16
17
18
19
20
21
22
23
24
AR3000
AR3002
MICOM_EYE_Q
3.3K
3.3K
OPT
+3.5V_ST
+3.3V_NORMAL
P50/INTP1/SI11/SDA11
P51/INTP2/SO11
P17/TI02/TO02
P16/TI01/TO01/INTP5
P15/PCLBUZ1/SCK20/SCL20
P14/RXD2/SI20/SDA20
P13/TXD2/SO20
P12/SO00/TXD0/TOOLTXD
P11/SI00/RXD0/TOOLRXD/SDA00
P10/SCK00/SCL00
P146
P147/ANI18
MICOM MODEL OPTION
+3.5V_ST
MICOM MODEL OPTION

10K
10K
10K
10K
0.72V 1.53V 2.27V 3.0V

R3010
R3006
R3004
R3008
MODEL_OPT_0 NON LOGO / LCD LOGO / LCD NON LOGO / OLED LOGO / OLED
MODEL_OPT_1 TV BOX TV BOX
MODEL_OPT_2 FHD UHD 8K

MODEL1_OPT_0(AM0)
MODEL1_OPT_1(AM1) MODEL_OPT_3
M16 A5LR M2
MODEL1_OPT_2(AM2) (FHD)
MODEL1_OPT_3(AM3) MODEL_OPT_3
M16 RTK H15
(UHD)
check WOL power K2H
POWER_DET
SOC_RESET
EDID_WP
AMP_MUTE
WOL/ETH_POWER_ON
POWER_ON/OFF1
WOL_CTL
SOC_TX
SOC_RX
PANEL_CTL
10K
10K
10K
10K
OPT
OPT
OPT
OPT
R3007
R3009
R3011
R3005
For CEC
+3.5V_ST
R3033 R3034
27K 120K
G
D3000
BAT54_TSC
CEC_REMOTE HDMI_CEC
LED_R
WOL_CTL
S
D
EBK63231501
SSM3K56FS
Q3001

FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS K2L / K2Lp 2015-06-13
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MICOM 30
MICOM MODEL OPTION
0.72V 1.53V 2.27V 3.0V
(2.7K) (8.2K) (20K) (75K)
MODEL_OPT_0(AM0)
NON LOGO / LCD LOGO / LCD NON LOGO / OLED LOGO / OLED
MODEL_OPT_1(AM1)
TV_NON_EPI BOX_NON_EPI TV_EPI BOX_NON_EPI
MODEL_OPT_2(AM2)
FHD UHD 8K
MODEL_OPT_3(AM3)
M16 A5LR M2
(FHD)
MODEL_OPT_3(AM3)
M16 RTK H15
(UHD)
0.72V 1.53V 2.27V 3.0V

(2.7K) (8.2K) (20K) (75K)
MODEL_OPT_0(AM0) MICOM_NON_LOGO/LCD MICOM_LOGO/LCD MICOM_NON_LOGO/OLED MICOM_LOGO/OLED

R3005-*1 2.7K R3005-*2 8.2K R3005-*3 20K R3005-*4 75K
MODEL_OPT_1(AM1) MICOM_TV_NON_EPI MICOM_TV_EPI

R3007-*1 2.7K R3007-*3 20K
MODEL_OPT_2(AM2) MICOM_FHD MICOM_UHD MICOM_8K

R3009-*1 2.7K R3009-*3 20K R3009-*4 75K
MODEL_OPT_3(AM3)
(FHD) MICOM_M16 MICOM_RTK MICOM_H15/A5LR MICOM_M2
R3011-*1 2.7K R3011-*3 20K R3011-*4 75K
R3011-*2 8.2K
MODEL_OPT_3(AM3)
(UHD)

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MODEL OPTION 30
ESD_HDMI_AMOTECH_2
ADMC 5M 02 200L
5V_HDMI_3 5V_DET_HDMI_3
R3315
EAF61530101
VA3300-*1
R3302 1.8K
EAF61530102
ESD_HDMI
R3317
1K
VA3300
3.3K
R3307
BODY_SHIELD
4.7K
0TRKE80046A C R3303 HDMI_EXT_EDID_NON 20
ADUC 20S 02 010L EAF61630102
Q3300
2N3904S B 1K 19
ESD_HDMI
HOT_PLUG_DETECT
BJT_KEC_1 HDMI_HPD_3
VA3302
18
VDD[+5V]
R3300 HDMI_EXT_EDID 17
100K R3312 DDC/CEC_GND
E 4.7K 16
SDA
ESD_HDMI_AMOTECH_2
15
SCL
HDMI_EXT_EDID
ESD_HDMI_AMOTECH_2
ESD_HDMI_AMOTECH_2
14
ADUC 20S 02 010L
ADMC 5M 02 200L
C R3337 RESERVED
SHIELD 0 13
CEC
DDC_BUFFER_SDA 12
B TMDS_CLK-
Q3300-*1
EAF61530101
11
20
EAF61530301
TMDS_CLK_SHIELD
MMBT3904(NXP) DDC_BUFFER_SCL
VA3311-*1
10
EAF61530301
BJT_NXP_2 0 TMDS_CLK+
VA3309-*1
E R3338 9
VA3302-*1
TMDS_DATA0-
19 HDMI_EXT_EDID 8
HPD
TMDS_DATA0_SHIELD
R3326
7
TMDS_DATA0+
ESD_HDMI
EAF61630102
18 AR3304 6 1.8K
VA3309
TMDS_DATA1-
+5V_POWER
R3331
33 HDMI_EXT_EDID_NON 5 R3305
3.3K
TMDS_DATA1_SHIELD
17 1/16W R3336 4 1K
R3308
ESD_HDMI_AMOTECH_2
TMDS_DATA1+
DDC/CEC_GND 0 3
DDC_SDA_3 4.7K
EAF61530102
TMDS_DATA2-
0TRKE80046A C
ADUC 20S 02 010L
16 2
R3306
SDA
TMDS_DATA2_SHIELD
Q3302
DDC_SCL_3 B 1K
ESD_HDMI
1
EAF61630102
ESD_HDMI
ESD_HDMI
TMDS_DATA2+
2N3904S
EAF61630102
HDMI_HPD_CBUS_1
VA3307
VA3311
0
VA3306
ESD_HDMI_AMOTECH_2
15 BODY_SHIELD
SCL R3335 R3320BJT_KEC_1
EAF61530301
ADUC 20S 02 010L
5501-56219
HDMI_EXT_EDID_NON 100K C
VA3306-*1
JK3302-*1
14 20 E
NC HDMI_JACK_CNPLUS
OPT
CEC_REMOTE B
13 Q3302-*1
EAF61530301
ESD_HDMI_AMOTECH_2
CEC 19 MMBT3904(NXP)
BJT_NXP_2
VA3307-*1
ADUC 20S 02 010L

12 HOT_PLUG_DETECT
E
CLK- 18 AR3305
11 VDD[+5V] 33
ESD_HDMI_AMOTECH_2
EAF61530301
CLK_SHIELD 17 1/16W
ADUC 20S 02 010L

DDC/CEC_GND
VA3310-*1
10 DDC_SDA_1
CLK+ 16
EAF61630102
ESD_HDMI
EAF61630102
SDA DDC_SCL_1
ESD_HDMI
9
VA3310
EAF61530301
VA3313
DATA0- AR3306 15
SCL
VA3313-*1
8 5.1
DATA0_SHIELD 1/16W 14
7 RESERVED
DATA0+ CK-_HDMI3 CEC_REMOTE
13
6 CK+_HDMI3 CEC AR3308
DATA1- 5.1
D0-_HDMI3 12 1/16W
5 TMDS_CLK-
D0+_HDMI3
DATA1_SHIELD 11 CK-_HDMI1
4 TMDS_CLK_SHIELD
AR3307 CK+_HDMI1
DATA1+ 5.1 10
3 1/16W TMDS_CLK+ D0-_HDMI1
DATA2- 9 D0+_HDMI1
D1-_HDMI3 TMDS_DATA0-
2
DATA2_SHIELD D1+_HDMI3 8
1 TMDS_DATA0_SHIELD
D2-_HDMI3
DATA2+ 7
D2+_HDMI3 TMDS_DATA0+ AR3309
6 5.1
TMDS_DATA1- 1/16W
YKF45-7058V
5 D1-_HDMI1
JK3301 TMDS_DATA1_SHIELD
HDMI3 with EEPROM 4
TMDS_DATA1+
D1+_HDMI1
D2-_HDMI1
3 D2+_HDMI1
TMDS_DATA2-
2
ESD_HDMI_AMOTECH_2
ADMC 5M 02 200L
TMDS_DATA2_SHIELD
1
TMDS_DATA2+
ESD_HDMI_AMOTECH_2
EAF61530101
ADUC 20S 02 010L
VA3303-*1
05008WR_H19C
R3313
EAF61530301
JK3302
ESD_HDMI
VA3301-*1
1.8K
EAF61630102
VA3301
HDMI_JACK_DEV
R3314
R3304
3.3K
1K
R3311
C 4.7K
EAF61530102
Q3301 R3309
ESD_HDMI
B 1K
VA3303
2N3904S HDMI_HPD_2
R3301BJT_KEC_1
100K C
E
B
Q3301-*1
MMBT3904(NXP)
SHIELD BJT_NXP_2
E
20 AR3303
33
1/16W
19
HPD DDC_SDA_2
+5V_NORMAL
18
EDID external EEPROM & DDC BUFFER for HDMI3
ESD_HDMI_AMOTECH_2 EAF61630102
ESD_HDMI
DDC_SCL_2
ESD_HDMI
ARC
EAF61630102
+5V_POWER
VA3304
VA3305
17
R3321
DDC/CEC_GND
EAF61530301
10K
A2
A1
16 ESD_HDMI_AMOTECH_2
SDA VA3305-*1 HDMI_ARC D3308-*1
ADUC 20S 02 010L C3303 R3334 KDS184
15 0DD184009AA
SCL 0.01uF 180 +5V_NORMAL
HDMI_PULLUP_KEC_2
C
HDMI_ARC
14 50V
ADUC 20S 02 010L
ESD_HDMI_AMOTECH_2
5V_HDMI_3
ESD_HDMI
NC 5% +5V_NORMAL
ADMC 5M 02 200L
EAF61530102
VA3314
R3323
R3332
A1
A2
CEC_REMOTE
100
1%
13 HDMI_EXT_EDID 5V_HDMI_3
39K
CEC HDMI_EXT_EDID
C3304
EAF61530301
EAF61530101
MMBD6100
12 0.1uF
VA3314-*1
D3310
VA3304-*1
CLK-
C
16V
A2
A1
C3302
11 0.1uF
CLK_SHIELD
AR3310 Close to SOC MMBD6100 16V
10 5.1 D3308
CLK+ 1/16W E
HDMI_PULLUP_1 HDMI_EXT_EDID
C
9 DEV_PCA9517_EXTEDID 2N3904S
DATA0- CK-_HDMI2 HDMI_EXT_EDID EDID_WP HDMI_EXT_EDID
CK+_HDMI2 AR3312
IC3302 B Q3303 IC3301
8
DATA0_SHIELD
D0-_HDMI2
47K PCA9517DGKR C BR24G02FJ-3GTE2
1/16W HDMI_EXT_EDID
7 D0+_HDMI2
DATA0+ AR3301-*1
1/16W
6 AR3311 VCCA VCCB VCC A0
DATA1- 1 8 10K 8 1
5.1
5 1/16W HDMI_EXT_EDID
DATA1_SHIELD HDMI_EXT_EDID_NON R3330
D1-_HDMI2 SCLA SCLB AR3301 WP A1
4 DDC_BUFFER_SCL 2 7 1/16W 4.7K 7 2
DATA1+ D1+_HDMI2 DDC_SCL_3_1
47K
3 D2-_HDMI2
DATA2- SDAA SDAB SCL A2
D2+_HDMI2 DDC_BUFFER_SDA 3 6 DDC_SDA_3_1 DDC_BUFFER_SW 6 3
2 DDC_SCL_3
DATA2_SHIELD FROM HDMI PORT
1 GND EN HDMI_EXT_EDID SDA GND
DATA2+ 4 5 DDC_BUFFER_SW DDC_SDA_3 5 4
R3339
0
DDC_SCL_3_1 DDC_SCL_3
HDMI_EXT_EDID
YKF45-7058V R3340
JK3300 HDMI2 with ARC DDC_SDA_3_1
0
DDC_SDA_3
DDC pull-up
5V_HDMI_1
5V_HDMI_2 +5V_NORMAL
C3301
+5V_NORMAL 0.1uF
16V
A1
A2
A1
A2
C3300
A1
A2
A1
A2
D3305-*1 0.1uF
KDS184 16V MMBD6100 MMBD6100 D3309-*1
0DD184009AA D3305 D3309 KDS184
HDMI_PULLUP_1 HDMI_PULLUP_1 0DD184009AA
HDMI_PULLUP_KEC_2
C
C
C
HDMI_PULLUP_KEC_2
C
AR3300
AR3302
1/16W
1/16W
47K
47K
DDC_SDA_2 DDC_SDA_1
DDC_SCL_2 DDC_SCL_1

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. HDMI 33
HDMI
PLACE CLOSE TO JACK
R3821 0 PLACE CLOSE TO SOC
DTV/MNT_V_OUT
SPDIF OUT
R3822
C3819 OPT
1/4W
AV/COMPONENT REAR C3820
OPT
390pF 390pF
75
1%
50V 50V
OPT OPT
+3.3V_NORMAL OPTIC_FOXCONN
JK3800
OPTIC_SOLTEAM
JK3800-*1 Place JACK Side
2F01TC1-CLM97-4F JST1223-001
GND 1 GND
1
1608 sizs For EMI
Fiber Optic
Fiber Optic
0 R3832
VCC VCC COMP1_Y/CVBS
2
2
R3808
C3822 C3805 C3806
1/4W
VA3806 150pF 27pF 100pF C3811
75
1%
VIN 3 VINPUT 5.5V OPT 50V 50V 47pF
3
SPDIF_OUT OPT OPT

50V
4
4
C3800 VA3807 C3818
47pF 5.5V
FIX_POLE
0.1uF
SHIELD
50V 16V
OPT
+3.3V_NORMAL
JK3802
PPJ245-31
R3807
[ GN/YL]E-LUG
6A 10K
R3803 1608 sizs For EMI
1K
5A
[GN/YL]O-SPRING AV1_CVBS_DET
1608 sizs For EMI
4A
[GN/YL]CONTACT 0
VA3803 R3811 COMP1_Pb
5.6V
5B [BL]O-SPRING SIGN380008 +3.3V_NORMAL
C3810 C3812
27pF 27pF R3816 C3815
50V 50V 75 10pF
7C [RD1]E-LUG-S VA3804
OPT OPT 1% 50V
5.5V R3810
5C 10K
[RD1]O-SPRING
VA3805 R3802
4C [RD1]CONTACT 1K
5.5V 1608 sizs For EMI
COMP1_DET 0 R3809 COMP1_Pr
5D [WH]O-SPRING VA3800
5.6V C3809 C3813 R3817 C3814
R3800 27pF 27pF 75 10pF
VA3801 50V 50V 50V
4E 470K FOR EMI 1%
[RD2]CONTACT 5.6V OPT OPT
5E [RD2]O-SPRING
1608 sizs For EMI
6E [RD2]E-LUG R3812
R3805 6.8K 1%
COMP1/AV1/DVI_L_IN
VA3802 R3801 0
5.6V 470K
C3801 C3803 C3807 R3814
560pF 100pF 1000pF 10K
50V
50V 50V OPT 1%
OPT OPT
1608 sizs For EMI

R3813
R3806 6.8K 1%
COMP1/AV1/DVI_R_IN
0
C3802 C3804 C3808 R3815

560pF 100pF 1000pF 10K
50V
50V 50V OPT 1%
OPT OPT
JACK_HP_OUT/RS232C
EAG60841811
JK3801
RS232C +3.3V_NORMAL
PEJ034-01
E_SPRING
RIN1 3
DOUT1
R3818-*1 R3820
22uF
16V 10K
L3800 HP_OUT
HP_AMP_NON
BLM18PG121SN1D R3818 150 R_SPRING 4
HP_ROUT_AMP
HP_OUT HP_AMP
L3801 T_SPRING
R3819 150 5
HP_LOUT_AMP
BLM18PG121SN1D HP_AMP
HP_OUT HP_OUT R3819-*1 B_TERMINAL2 7B
HP_OUT 22uF
C3816 C3817
0.22uF 0.22uF 16V
25V 25V HP_AMP_NON T_TERMINAL2 6B
VA3808
5.6V
HP_OUT
R3804 1K
HP_DET
HP_OUT
HP OUT

FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS UF71/7500 2014-07-24
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. JACK_COMMON_H 38
WIFI POWER ENABLE CONTROL
+3.5V_WIFI
+3.5V_ST IC4100
TAEJIN TECHNOLOGY CO., LTD.
Discharge Resistor
IN OUT
1 6
R4102
C4100
3.3K
0.1uF GND EAN64148901 ILIMIT
2 5
WIFI_EN R4101 33 EN FLAG

3 4
1/16W
R4120
R4100
6.8K
10K
1%
OPT
Current Limit : 2.0A
P4100 +3.5V_WIFI
12507WR-H21L2B(BK)
C4110
C4113
C4108 10uF
10uF
VCC 0.1uF 10V 10V
1 NON_EASY_TV
WIFI_DIODE_SEMTECH
WIFI_DIODE_TOSHIBA
NON_EASY_TV NON_EASY_TV
USB D- R4113
2.2
IR
2 WIFI_DM
+3.5V_ST NON_EASY_TV
EAH61515101
EAH62735601
USB D+ R4114
2.2
3
D4100-*1
DEBUG_IR_PROTO
WIFI_DP
NON_EASY_TV
DEBUG_IR_PROTO
DEBUG_IR_PROTO
D4100
GND C4107 C4109
IC4101 4 5pF 5pF
AO-R123C7G-LG 50V 50V
R4103
1/16W
R4105
1/10W
WL_HOST_WAKE OPT OPT R4112

510
5
330
WOL/WIFI_POWER_ON
5%
47
5%
NON_EASY_TV C4104
GND GND R4118
G 0 0.1uF
6 3D_SYNC NON_EASY_TV
1/16W OPT R4111
VS BT_REG_ON 5% 510
V 7 M_RFModule_RESET
NON_EASY_TV
R4117
GND
OPT
OUT
O 8
2K
1/16W
0
3D_SYNC
R4119
WIFI_11N_ONLY
AR4101
100
SDA 1/16W
12 EYE_SDA
EYE_SCL
SCL
13 +3.5V_ST
JP-BLOCK-IR R4110
GND JP4101 10K
14 R4121 5%
GND
IR
ESD_READY
100
IR
IR
VA4110
C4105
15 100pF
50V
LED R4109
1.8K
16 LED_R
GND OPT
17 C4102
0.1uF
16V
+3.5V_ST
3.5v_ST
18
KEY2 C4106 +3.5V_ST
19 1000pF
50V
OPT
KEY1
20 R4115 R4116
10K 10K
GND R4104 1% 1%
21 100
KEY2
KEY1
R4106
ESD_READY ESD_READY 100
22
R4107
MICOM_KEY_ONE_KEY
ZD4110 ZD4111 MICOM_5KEY_JOG_TYPE
5V 5V
0
C4111 C4112
0.1uF 0.1uF
GND
OPT OPT

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. IR/KEY 12
USB2.0 2Port
OCP USB2_2.0
+3.3V_NORMAL
EAN62871401
+5V_USB_1 +5V_USB_1
USB1
USB_REAR
+5V_NORMAL IC4301 MAX 1.0A
USB-STRAIGHT
BD2242G (Rear Jack)
JK4302
USB_REAR
R4303 VIN VOUT US-04A-VSD
4.7K 1 6 USB_REAR
USB_REAR
value change USB_REAR R4309 2.2
C4301 USB_DM1 2
GND ILIM
0.1uF 2 5
10K(2.63V) --> 4.7K(2.97V) 16V USB_REAR 1
R4308 2.2 3
USB_DP1
USB_REAR
14K
R4305
1%
EN OC
DF3D6.8MS
USB_REAR_ESD_DIODE
3 4
/USB_OCD1
USB_REAR
C4322 C4323
D4301
D4302
4
10uF
5V
10uF
USB_CTL1 10V
10V
USB_REAR USB_REAR 5
R4301
10K
USB_REAR
JP4300
JP-BLOCK-USB
DM VBUS
DP GND

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. USB2.0 jack 13
+3.3V_NORMAL
+5V_USB_2
+5V_USB_2
USB2 +5V_NORMAL IC4400
MAX 1.0A USB_SIDE
BD2242G
USB_SIDE
R4403 VIN VOUT
USB_SIDE
1 6
1
JK4400
3AU04S-305-ZC-(LG)
4.7K
USB DOWN STREAM
value change USB_SIDE

USB_SIDE C4402 GND ILIM
R4400 2.2 0.1uF 2 5
USB3_DM0
2
10K(2.63V) --> 4.7K(2.97V)
USB_SIDE
16V
USB_SIDE
14K
R4404
1%
R4401 2.2 EN OC
USB3_DP0 /USB_OCD3_0 3 4
3
DF3D6.8MS
USB_SIDE_ESD_DIODE
USB_SIDE
USB_CTL3_0
D4400
C4400
4
C4401
ZD4400
10uF 10uF
5V
10V 10V R4402

10K
USB_SIDE
M4400
JP-BLOCK-USB
DM VBUS
DP GND
USB3_RXM0 /USB_OCD1
USB3_RXP0 USB_CTL1
USB3_TXM0
USB_DM1
USB3_TXP0 USB_DP1
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES 043.sht

FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS K2H 2015.02.11
USB 2 & 3 15 26
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Ethernet Block
NON_EASY_TV NON_EASY_TV
C5000 C5001
0.1uF 0.01uF
16V 50V
EAG35781018 EAG35781016 EAG35781010

LANJACK_HONGLIN_SUB2 LANJACK_FREEPORT_SUB1 LANJACK_UDE_MAIN
JK5000-*2 JK5000-*1 JK5000
B50(512-10)F4-03A-A013-B52 26TM9G-30100-02HF RJ45VT-01SN002
1 1 1
1 1 1
EPHY_TDP
2 2 2
2 2 2
3 3 3
3 3 3
EPHY_TDN
4 4 4
4 4 4
EPHY_RDP
5 5 5
5 5 5
6 6 6
6 6 6
EPHY_RDN
7 7 7
7 7 7 NON_EASY_TV NON_EASY_TV NON_EASY_TV NON_EASY_TV
VA5000 VA5001 VA5002 VA5003
8 8 8 5.5V 5.5V 5.5V 5.5V
8 8 8
9 9 9
9 9 9
NON_EASY_TV
L5000
PZ1608U121-2R0TF
R5000 0
OPT
NON_EASY_TV
L5001
PZ1608U121-2R0TF
R5001 0
OPT

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LAN_H 50
AUDIO AMP(NTP7515)
R5806-*1
3K
SPK_WOOFER
+3.3V_NORMAL
R5805
AMP_RESET_N 100
NRS6045T100MMGK
1/16W
A13V +13V_AMP L5802
R5806 C5806
L5801 10.0uH
4.7K 1000pF
PZ1608U121-2R0TF 50V SPK_L+
L5800
UBW2012-121F SPK_WOOFER_NON
50V
AUD_SCK
+13V_AMP
22000pF
R5807
1/10W
C5807
3.3
R5811
5%
C5821
C5805 0.1uF 4.7K
50V
[EP]GND
0.1uF C5813
C5809 390pF
VDD_IO
GND_IO
PGND1A
PVDD1A
PVDD1B
16V 10uF 50V
CLK_I
RESET
BST1A
OUT1A
25V
C5819
0.47uF
50V
AD
C5814
390pF
50V C5822 R5812
R5808
1/10W
0.1uF SPEAKER_L
3.3
50V 4.7K
5%
NRS6045T100MMGK
40
39
38
37
36
35
34
33
32
31
L5805
NC_1 1 30 OUT1B 10.0uH
SPK_L-
VDD_PLL 2 29 PGND1B C5811

THERMAL 22000pF
NC_2 3 41 28 BST1B 50V
C5800
1uF
10V GND 4 27 VDR1
NC_3 5 IC5800 26 NC_5
C5801
1uF
10V
DVDD 6 NTP7515 25 AGND
AUD_LRCH
SDATA 7 24 VDR2
WCK
0x54 BST2A
C5817
1uF
C5818
1uF
AUD_LRCK 8 23 10V 10V
NC_4 9 AMP_NTP7515 22 PGND2A C5812

22000pF
AR5800
100 SDA 10 21 OUT2A 50V
I2C_SDA4
11
12
13
14
15
16
17
18
19
20
I2C_SCL4
NRS6045T100MMGK
C5802 C5804
33pF 33pF L5803
50V 50V 10.0uH
SCL
FAULT
MONITOR_0
MONITOR_1
MONITOR_2
BST2B
PGND2B
OUT2B
PVDD2B
PVDD2A
SPK_R+
+3.3V_NORMAL
R5809
1/10W
+13V_AMP
3.3
5%
C5823 R5813
R5801 0.1uF 4.7K
10K C5815 C5820 50V
390pF 0.47uF
R5804 C5810 50V 50V
SPEAKER_R
10uF C5816
C 100 390pF
25V 50V
R5800 C5803 C5824 R5814
R5810
1/10W
B Q5800 C5808 NRS6045T100MMGK
AMP_MUTE 1000pF 0.1uF 4.7K
3.3
2N3904S 50V
5%
10K 22000pF L5804 50V
WOOFER_MUTE
E 50V 10.0uH
I2S_AMP
SPK_R-
[EP]GND
VDD_IO
GND_IO
PGND1A
PVDD1A
PVDD1B
CLK_I
RESET
BST1A
OUT1A
AD
4P Box type
40
39
38
37
36
35
34
33
32
31
NC_1 1 30 OUT1B
WAFER-ANGLE
VDD_PLL 2 29 PGND1B TP5801 WOOFER_MUTE
THERMAL
NC_2 3 41 28 BST1B
TP5802 I2S_AMP
GND 4 27 VDR1
SPK_L+
NC_3 NC_5 4
5 IC5800-*1 26
DVDD 6 NTP7515D 25 AGND
SDATA 7 AMP_NTP7515D 24 VDR2 SPK_L-
3
WCK 8 23 BST2A
NC_4 9 22 PGND2A
SPK_R+
SDA OUT2A 2
10 21
11
12
13
14
15
16
17
18
19
20
SPK_R-
1
SCL
FAULT
MONITOR_0
MONITOR_1
MONITOR_2
BST2B
PGND2B
OUT2B
PVDD2B
PVDD2A
P5800
SPK_WOOFER_NON

FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS 2014-10-17
MAIN_AMP 58
EARPHONE AMP
IC6100
TPA6138A2
H/P out R/C filter

HP_AMP HP_AMP H/P out R/C filter
Close to Main SOC HP_AMP +INR +INL
C6104 1 14 C6109 HP_AMP Close to Main SOC
(ready for debugging) C6100 HP_AMP HP_AMP
HP_AMP HP_AMP 18pF HP_AMP C6101 (ready for debugging)
2.2uF 18pF 2.2uF
R6108 10V R6100 R6106 R6104 R6101 R6109
0 10K 43K -INR -INL HP_AMP 43K 10K 10V 0
HP_AMP 2 13
HP_ROUT C6110 HP_LOUT
HP_AMP
R6103
HP_AMP
R6102
1% C6108 1% HP_AMP_NON C6111
0.01uF HP_AMP_NON C6106
43K
43K
10pF R6110 0.01uF
1%
1%
OPT R6107 OUTR OUTL 10pF
0 50V 3 12 50V 0 OPT
HP_LOUT_AMP
HP_ROUT_AMP
+3.3V_NORMAL GND_1 UVP
4 11
MUTE GND_2 +3.3V_NORMAL

4.7K
HP_AMP
5 10
R6105
SIDE_HP_MUTE VSS VDD

6 9
HP_AMP HP_AMP
HP_AMP
C6105 C6107
C6102 CN CP 1uF 0.1uF
1uF 7 8
10V 16V
10V
C6103
1uF
10V
HP_AMP

HP_AMP 61
FE_DEMOD1_TS_ERROR
FE_DEMOD2_TS_ERROR
1. should be guarded by ground

close to Tuner 2. No via on both of them
3. Signal Width >= 12mils
Signal to Signal Width = 12mils
Ground Width >= 24mils
TU_I2C_EU TU_I2C_EU
C6505-*1 TU_W_BR/TW
C6503-*1 TU_ALL
47pF 47pF AR6500-*1
AR6500
50V 50V 33 200
1/16W
1 I2C_SCL5_TU TU_I2C_NON_EU I2C_SCL2
C6505
150pF I2C_SDA2
50V
2 I2C_SDA5_TU
TU_I2C_NON_EU
C6503 +3.3V_NORMAL
150pF 1608 perallel
50V TU_ALL because of derating
L6501 +3.3V_NORMAL
PZ1608U121-2R0TF TU_EXT_ATV
TU_EXT_ATV
3 R6516 R6517
+3.3V_LNA_TU 200
C6512 200
C6510 0.1uF
0.1uF OPT TU_CVBS
E E
TU_ALL
4 TU_EXT_ATV_NXP_2
TU_CVBS_TU TU_EXT_ATV_KEC_1 MMBT3906(NXP)
TU_ALL_IntDemod B Q6502 B Q6502-*1
R6506 1K 2N3906S-RTK
5 IF_AGC_TU IF_AGC C C
C6502 close to Tuner TU_ALL_IntDemod SIF pin only Ready for K2H
0.1uF
16V
TU_EXT_ATV
TU_SIF_TU IF_P_MAIN
R6513 0
6 R6504
0
IF_P_TU
TU_ALL_IntDemod C6519 IF_P_MAIN
7 33pF L6502
should be guarded by ground,Match GND VIA R6505 TU_N_KR_K2LP OPT
0
IF_N_TU C6520 IF_N_MAIN
TU_ALL_IntDemod 33pF
8 TU_N_KR_K2LP TU_N/D
R6501
TU_N/D 100 /TU_RESET1
9 /TU_RESET1_TU
C6507
+3.3V_NORMAL
Global F/E Option Name 16V
0.1uF
1. TU 10 TU_N/D TU_ALL
L6503
2. Tuner Name = TDJH,TDjM... +3.3V_TU_I2C PZ1608U121-2R0TF
L6506
3. Country Name = KR,US,BR,EU ... PZ1608U121-2R0TF
T2 : Max 1.7A
11 +3.3V_TU C6521
C6511 0.1uF else : Max 0.7A
Example of Option name 0.1uF TU_ALL
12 TU_N/D TU_N/D
TU_ALL_IntDemod = All Tuner type for Internal demod LNB_TX LNB_TX
L6505
TU_M/W = apply TDSM&TDSW Type Tuner PZ1608U121-2R0TF Demod_Core
Demod_Core TU_N/D
TU_N/D
13
D_Demod_Core
TU_M/W IC6500
C6506 close to Tuner TJ2132GDP [EP]GND
14 Tuner Type for Global 0.1uF
10K
R6521
TDJH-G101D : Half NIM for EU,AJJA
TDJH-H101F : Half NIM for US, KR POK GND R2
1 8
TDJK-T101F : Half NIM for TW
THERMAL
TU_N/D
10.5K
R6519
14 FE_DEMOD1_TS_ERROR FE_DEMOD1_TS_ERROR
TDJM-C301D,F : FULL NIM for China +3.5V_ST 10K EN FB
9
2 7
TU_N/D
TDJM-B101F : Brazil NIM with Isolater Type R6500
R1
TDJM-K101F : colombia NIM 15 FE_DEMOD1_TS_CLK FE_DEMOD1_TS_CLK POWER_ON/OFF2_2
IN OUT
TDJM-G101D,G105D,G151D : EU Combo&Full NIM 3 6
OPT
TDJM-H101F,H151F : Korea PIP tuner 16 FE_DEMOD1_TS_SYNC FE_DEMOD1_TS_SYNC +5V_NORMAL C6504
TDJW-A151D : AJJA T2 PIP BIAS
4 2A 5
SS 16V
0.1uF TU_N/D
17 FE_DEMOD1_TS_VAL FE_DEMOD1_TS_VAL C6518
C6500 10uF
10uF C6501 10V
C6515
FE_DEMOD1_TS_DATA[0] 10V 1uF 2700pF
18 TU_N/D 25V 50V
TU_N/D TU_N/D
FE_DEMOD1_TS_DATA[1] FE_DEMOD1_TS_DATA[0-7]
19
20 FE_DEMOD1_TS_DATA[1]
Vout=0.6*(1+R1/R2)
21
FE_DEMOD1_TS_DATA[5] FE_DEMOD1_TS_DATA[7]
23
LNB_OUT LNB_OUT
26

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. TU_CIRCUIT 18
TU_A_BR TU_S_US TU_N_EU TU_N_CH
TU6703 TU6700 TU6701 TU6704
TDJA-T301F TDJS-H301F TDJN-G301D TDJN-C301D
SCL_RF SCL_RF SCL_RF SCL_RF

1 1 1 1 I2C_SCL5_TU 1
SDA_RF SDA_RF SDA_RF SDA_RF
2 2 2 2 I2C_SDA5_TU 2
B1[+3.3V_RF] B1[+3.3V_RF] B1[+3.3V_RF] B1[+3.3V_RF]
3 3 3 3 +3.3V_LNA_TU 3
CVBS CVBS CVBS CVBS
4 4 4 4 TU_CVBS_TU 4
IF_AGC IF_AGC IF_AGC IF_AGC
5 5 5 5 IF_AGC_TU 5
SIF SIF SIF SIF
6 6 6 6 TU_SIF_TU 6
IF[N] IF[N] IF[N] IF[N]
7 7 7 7 IF_N_TU 7
IF[P] IF[P] IF[P] IF[P]
8 8 8 8 IF_P_TU 8
GND_1 GND
9 9 9
9 9
RESET_DEMOD RESET_DEMOD
10 10 /TU_RESET1_TU 10
SHIELD SHIELD
B2[+3.3V_DEMOD] B2[+3.3V_DEMOD]
11 11 +3.3V_TU 11
F22 NC
12 12 LNB_TX 12
B3[+1.2V_DEMOD] B3[+1.2V_DEMOD]
13 13 D_Demod_Core 13
ERROR ERROR
14 14 FE_DEMOD1_TS_ERROR 14
MCLK MCLK
15 15 FE_DEMOD1_TS_CLK_1
SYNC SYNC
16 16 FE_DEMOD1_TS_SYNC_1 16
VALID VALID
17 17 FE_DEMOD1_TS_VAL_1 17
D0 D0
18 18 FE_DEMOD1_TS_DATA0_1 18
D1 D1
19 19 FE_DEMOD1_TS_DATA[1] 19
D2 D2
D3 D3
D4 D4
22 22 FE_DEMOD1_TS_1_DATA[4] 22
D5 D5
LNB
26 LNB_OUT 26 D6 D6
GND_2
27 27 D7 D7
28 26
TU_N_KR TU_N_CO TU_N_AJ
TU6701-*1 TU6701-*2 SHIELD TU6701-*3 SHIELD
TDJN-H203F TDJN-K301F TDJN-G305D
SCL_RF SCL_RF SCL_RF

1 1 1
SDA_RF SDA_RF SDA_RF
2 2 2
B1[+3.3V] B1[+3.3V] B1[+3.3V_RF]
3 3 3
CVBS CVBS CVBS
4 4 4
AIF_AGC AIF_AGC IF_AGC
5 5 5
SIF SIF SIF
6 6 6
AIF[N] AIF[N] IF[N]
7 7 7
AIF[P] AIF[P] IF[P]
8 8 8
GND_1 GND_1 GND_1
9 9 9
RESET_DEMOD RESET_DEMOD RESET_DEMOD
10 10 10
B2[+3.3V] B2[+3.3V] B2[+3.3V_DEMOD]
11 11 11
F22_OUTPUT F22_OUTPUT NC
12 12 12
B3[+1.2V] B3[+1.2V] B3[+1.2V_DEMOD]
13 13 13
ERROR ERROR ERROR
14 14 14
MCLK MCLK MCLK
15 15 15
SYNC SYNC SYNC 0 R6702
16 16 16 FE_DEMOD1_TS_CLK_1 FE_DEMOD1_TS_CLK PCM_5V_CTL
0 R6703
FE_DEMOD1_TS_SYNC_1 FE_DEMOD1_TS_SYNC SMARTCARD_DATA
VALID VALID VALID 0 R6704
17 17 17 FE_DEMOD1_TS_VAL_1 FE_DEMOD1_TS_VAL SMARTCARD_RST
0 R6705
FE_DEMOD1_TS_DATA0_1 FE_DEMOD1_TS_DATA[0] CAM_IREQ_N
DATA0 DATA0 D0 SMARTCARD_DET
18 18 18
SMARTCARD_CLK
DATA1 DATA1 D1 /TU_RESET2
19 19 19 SMARTCARD_PWR_SEL
DATA2 DATA2 D2
20 20 20
DATA3 DATA3 D3
21 21 21
TU_N/D_NON_JP 0 R6712
DATA4 DATA4 D4 FE_DEMOD1_TS_1_DATA[4] FE_DEMOD1_TS_DATA[4]
22 22 0 R6713
22 FE_DEMOD1_TS_1_DATA[5]
TU_N/D_NON_JP
TU_N/D_NON_JP 0 R6714
DATA5 DATA5 D5 FE_DEMOD1_TS_1_DATA[7]
0 R6715
FE_DEMOD2_TS_ERROR
23 23 23 FE_DEMOD1_TS_1_DATA[6] TU_N/D_NON_JP FE_DEMOD1_TS_DATA[6]
LNB LNB LNB
26 DATA6 26 DATA6 26 D6
GND_2
24 24
GND_2
24 Close to Tuner
GND_2
27 DATA7 27 DATA7 27 D7
25 25 25
28 28 28
SHIELD SHIELD SHIELD

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. TU_SYMBOL_H 19
LNB PART (DVB-S2)
OPTION ; LNB
Input trace widths should be sized to conduct at least 3A

Ouput trace widths should be sized to conduct at least 2A
3A
+13V_M
Max 1.3A
LNB
D6902 LPH6050T-150M-R
D6904 L6900
LNB SX34
40V 40V 15uH

LNB A_GND
C6909
2A C6903 C6905 C6906 C6907
10uF
25V
0.01uF 10uF 10uF 10uF LNB
50V 25V 25V 25V
LNB LNB LNB LNB
C6908 0.1uF
Closed to Boost Pin (#1) A_GND

LNB
Close to VIN pin (#15) Need Isolated GND

R6904
C6910 0
A_GND
BOOST
GNDLX
0.1uF
[EP]
VIN
50V
LX
LNB
16
15
14
13
VCP GND A_GND
D6901 1 12
SS2040LL-LG THERMAL LNB
LNB 2 11 VREG
LNB_OUT 17
R6903
40V NC ISET 39K
D6903 3 IC6901 10
SX34
LNB C6904
0.1uF LNB A8305SESTR
C6900 C6901 R6900 IRQ TCAP C6912 1/16W
LNB 50V 40V 4 LNB 9 1%
0.1uF 33pF 2.2K
LNB LNB D6900 1W C6902 LNB
5
LNB LNB 0.22uF 0.1uF

LNB 25V
SCL
SDA
ADD
TONECTRL
0.22uF
Close to Tuner A_GND
A_GND
LNB
Surge Protection
C6911
LNB
+13V_M
Q6901
+13V +13V_M
LNB_JAPAN LNB_JAPAN
AO3435
R6901
D
27K
C6913 R6910 C6915
NON_JAPAN_LNB
R6902-*1
0.1uF 36K 0.1uF
G
50V LNB 50V
R6902
LNB LNB
10K
LNB
33
AR6900
R6911
0
150K
LNB
LNB_NON_Tx
+3.3V_NORMAL
LNB_Tx
R6905
R6908
LNB C EBK61012601
R6909 LNB
0
10K B Q6900
MMBT3904(NXP)
1/16W OPT
5% C6914 E
4.7uF
10V
I2C_SCL2
I2C_SDA2
LNB_TX

ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR 20
LNB
+3.3V_NORMAL
+3.3V_NORMAL
OPT
OPT R7129
LGD/BOE_PANEL_VX1 +1.8V R7127 1K
R7136 1K LOCKAn
10K OPT
R7128 C
100
LGD/BOE_PANEL_VX1 OPT B Q7103
R7114 0 R7121 2N3904S
LOCKAn OPT
LOCKAn_IN 10K
E
0
OPT
[51P Vx1
OPT
C
R7122
R7117
100 B Q7102
output wafer] LOCKAn_IN
2N3904S
E OPT
LGD/BOE_PANEL_VX1
P7100
SP14-11592-01-51Pin
+3.3V_NORMAL
1
LGD/BOE_PANEL_VX1
2 C7102 0.1uF
TXDBP0_L LGD/BOE_PANEL_VX1
LGD/BOE_PANEL_VX1
3 C7103 0.1uF R7118
TXDBN0_L
10K
4
LGD/BOE_PANEL_VX1 LGD/BOE_PANEL_VX1
5 C7104 0.1uF R7113 0
TXDBP1_L HTPDAn
LGD/BOE_PANEL_VX1
6 C7105 0.1uF HTPDAn_IN
TXDBN1_L
OPT
7
LGD/BOE_PANEL_VX1
R7126
8 C7106 0.1uF
TXDBP2_L
LGD/BOE_PANEL_VX1 EPI Share Lane
9 C7107 0.1uF
TXDBN2_L
10
LGD/BOE_PANEL_VX1
11 C7108 0.1uF
TXDBP3_L
LGD/BOE_PANEL_VX1
12 C7109 0.1uF
TXDBN3_L
13
LGD/BOE_PANEL_VX1
C7102~C7117
C7110 0.1uF
14
15 C7111
LGD/BOE_PANEL_VX1
0.1uF
TXDBP4_L
TXDBN4_L
Close to EPI Wafer!
16
LGD/BOE_PANEL_VX1
17 C7112 0.1uF M+ LGD_Module
TXDBP5_L +3.3V_NORMAL
LGD/BOE_PANEL_VX1 High : AGP & M+ BYPASS
18 C7113 0.1uF L & NC : NSB & M+ ENABLE
TXDBN5_L OPT
AGP_CTRL R7104
19 10K
R7101
LGD/BOE_PANEL_VX1 0
20 C7114 0.1uF
TXDBP6_L AGP_CTRL
LGD/BOE_PANEL_VX1 +3.3V_NORMAL
21 C7115 0.1uF VBY1_LGD/BOE_M+_MODULE
TXDBN6_L
R7105
22 VBY1_LGD_M+_MODULE 1K
R7130 1/16W
LGD/BOE_PANEL_VX1 1K
23 C7116 0.1uF 5%
TXDBP7_L
LGD/BOE_PANEL_VX1 +3.3V_NORMAL
24 C7117 0.1uF R7137
TXDBN7_L TCON_I2C_EN
100
25 VX1_MSE
VBY1_LGD_M+_MODULE R7115
G
26 OPT 4.7K
LOCKAn_IN OPT LGD_PANEL_VX1_FET
R7107
27 HTPDAn_IN 0 I2C_SCL6
S
28 Q7100
T2N7002AK
LGD_PANEL_VX1
29 AR7101 R7119
R7125 0
0 1/16W 33 OPT
30
NON_BOE MODULE OPT *Pin31(BIT_SEL) 3D&L_DIM_EN_Micom
31 +3.3V_NORMAL
HIGH or NC : 10Bit R7108 0 TCON_I2C_EN
R7102 10K +3.3V_NORMAL 3D&L_DIM_EN
LOW : 8Bit
32
R7116
G
33 R7100 4.7K
10K OPT LGD_PANEL_VX1_FET
34 VBY1_LGD/BOE_M+_MODULE
I2C_SDA6
S
R7131 0
35 Q7101
DATA_FORMAT_0 T2N7002AK
VBY1_LGD/BOE_M+_MODULE (MPLUS MODE 1)
36 R7106
10K R7120
37 OPT
33 OPT
38 +3.3V_NORMAL
VBY1_LGD_M+_MODULE
R7124
39 PWM_DIM
R7111
0 10K
40 Non_LGD_60Hz
VBY1_LGD/BOE_M+_MODULE
41 R7123 10K R7132 0
Input Data Format[1:0]=[35pin:36pin]
DATA_FORMAT_1 00 : Low Power(MLE Off)
42 VBY1_LGD/BOE_M+_MODULE
01 : High Luminance (MLE3)
LGD/INX/BOE_Module
43 (MPLUS MODE 0) 10 : High Luminance (MLE1,2)

OPT
R7103
44 R7112 11 : PC Mode
10K
45
0
46
47 +3.3V_NORMAL
R7133 0
48 DATA_FORMAT_0
OPT
49 R7109
10K
50 OPT
PANEL_VCC
51 R7134 0
PWM_TCON_OUT
L7100 VBY1_LGD/BOE_M+_MODULE
52 MLB-201209-0120P-N2
PANEL_VX1_51P_VCC OPT
C7100 C7101 R7110

10K
10uF 10uF
25V 25V
PANEL_VX1_51P_VCC PANEL_VX1_51P_VCC
Data Input Format[1:0]
*Mode 1 (NON Division)

- Data Format 0(Pin37) = Low
Data Format 1(Pin36) = Low
*Mode 3 (4 Division)
- Data Format 0(Pin37) = Low
Data Format 1(Pin36) = High
Must be assigned at Vx1 51p wafer !!!
PWM_TCON_OUT

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. Vx1 51P 21
eMMC I/F
DVDD18_EMMC 3.3v power delete, 131120
R8117
R8116
1/16W
10K
AR8104
1/16W
10K
AR8103
10K
10K
IC8100 EMMC_SAMSUNG EMMC_8G_TOSHIBA

THGBMBG5D1KBAIL IC8100-*1
IC8100-*2
EMMC_8G_SAMSUNG
KLM4G1FEPD-B031 IC8100-*3
EMMC_DATA[0-7] AR8100 THGBMFG6C1LBAIL KLM8G1GEND-B031
EMMC_DATA[0] 0
A3 C7
1/16W A4
DAT0 NC_22
C8 A3 C8 A3 C7
EMMC_DATA[1] A3 C8 A5
DAT1 NC_23
C9 A4
DAT0 NC_23
C9 A4
DAT0 NC_22
C8
DAT2 NC_24 DAT1 NC_24 DAT1 NC_23
EMMC_DATA[2] DAT0 NC_23 DAT6 B2
DAT3 NC_25
C10 A5
DAT2 NC_25
C10 A5
DAT2 NC_24
C9
A4 C9 B3
DAT4 NC_26
C11 B2
DAT3 NC_26
C11 B2
DAT3 NC_25
C10
DAT1 NC_24 B4
DAT5 NC_27
C12 B3
DAT4 NC_27
C12 B3
DAT4 NC_26
C11
EMMC_DATA[3] A5 C10 B5
DAT6 NC_28
C13 B4
DAT5 NC_28
C13 B4
DAT5 NC_27
C12
DAT2 NC_25 B6
DAT7 NC_29
C14 B5
DAT6 NC_29
C14 B5
DAT6 NC_28
C13
EMMC_DATA[4] B2 C11 NC_30

D1 B6
DAT7 NC_30
D1 B6
DAT7 NC_29
C14
DAT3 NC_26 NC_31
D2 NC_31
D2
NC_30
D1
EMMC_DATA[5] B3 C12 M6
CLK NC_32
D3 NC_32
D3
NC_31
D2
DAT4 NC_27 M5
CMD NC_33
D4 M6
CLK NC_33
D4 M6
CLK NC_32
D3
EMMC_DATA[6] B4 C13 NC_34

D12 M5
CMD NC_34
D12 M5
CMD NC_33
D4
DAT5 NC_28 NC_35
D13 NC_35
D13
NC_34
D12
B5 C14 A7
RFU_1 NC_36
D14 NC_36
D14
NC_35
D13
EMMC_DATA[7] DAT6 NC_29 E5

RFU_2 NC_37
E1 A6
VSS_1 NC_37
E1 A7
RFU_2 NC_36
D14
B6 D1 G3
RFU_3 NC_38
E2 A7
RFU_2 NC_38
E2 E5
RFU_3 NC_37
E1
DAT7 NC_30 EMMC_DATA[5] K6
RFU_4 NC_39
E3 C5
NC_21 NC_39
E3 E8
RFU_4 NC_38
E2
D2 K7
RFU_5 NC_40
E12 E5
RFU_4 NC_40
E12
NC_39
E3
E13
NC_31 E8
RFU_6 NC_41
E13 E8
RFU_5 NC_41 G3
RFU_5 NC_40
E12
D3 E9
RFU_7 NC_42
E14 E9
VSF_1 NC_42
E14 G10
RFU_6 NC_41
E13
F1
NC_32 E10
RFU_8 NC_43
F1 E10
VSF_2 NC_43 K6
RFU_7 NC_42
E14
M6 D4 F10
RFU_9 NC_44
F2 F10
VSF_3 NC_44
F2 K7
RFU_8 NC_43
F1
CLK NC_33 G10
RFU_10 NC_45
F3 G3
RFU_9 NC_45
F3 K10
RFU_9 NC_44
F2
M5 D12 K10
RFU_11 NC_46
F12 G10
RFU_10 NC_46
F12 P7
RFU_10 NC_45
F3
CMD NC_34 P10
RFU_13 NC_47
F13 H5
DS NC_47
F13 P10
RFU_11 NC_46
F12
D13 H5
DS NC_48
F14 J5
VSS_5 NC_48
F14
NC_47
F13
eMMC V5.0 GND NC_35

D14 NC_49
G1
G2
K6
K7
RFU_13 NC_49
G1
G2
H5
DATASTROBE NC_48
F14
G1
NC_50 RFU_14 NC_50 NC_49
K10 G12
NC_36 NC_51
G12
RFU_15 NC_51 E9
RFU_12 NC_50
G2
A6 E1 NC_52
G13 P7
RFU_16 NC_52
G13 E10
RFU_13 NC_51
G12
VSS_1 NC_37 NC_53
G14 P10
RFU_17 NC_53
G14 F10
RFU_14 NC_52
G13
A7 E2 NC_54
H1 NC_54
H1
NC_53
G14
RFU_2 NC_38 K5
RSTN NC_55
H2 NC_55
H2
NC_54
H1
C5 E3 NC_56
H3 K5
RSTN NC_56
H3 K5
RSTN NC_55
H2
NC_21 NC_39 NC_57
H12 NC_57
H12
NC_56
H3
E5 E12 C6
VDD_1 NC_58
H13 NC_58
H13
NC_57
H12
RFU_4 NC_40 M4
VDD_2 NC_59
H14 C6
VCCQ_1 NC_59
H14 C6
VDD_1 NC_58
H13
E8 E13 N4
VDD_3 NC_60
J1 M4
VCCQ_2 NC_60
J1 M4
VDD_2 NC_59
H14
R8120 0 RFU_5 NC_41 P3

VDD_4 NC_61
J2 N4
VCCQ_3 NC_61
J2 N4
VDD_3 NC_60
J1
E9 E14 P5
VDD_5 NC_62
J3 P3
VCCQ_4 NC_62
J3 P3
VDD_4 NC_61
J2
EMMC_CLK VSF_1 NC_42 NC_63
J12 P5
VCCQ_5 NC_63
J12 P5
VDD_5 NC_62
J3
E10 F1 J13 NC_64
J13 J12
DAT7
NC_64 NC_63
EMMC_CMD VSF_2 NC_43 E6
VDDF_1 NC_65
J14 NC_65
J14
NC_64
J13
F10 F2 F5
VDDF_2 NC_66
K1 E6
VCC_1 NC_66
K1 E6
VDDF_1 NC_65
J14
EMMC_RST VSF_3 NC_44 J10
VDDF_3 NC_67
K2 F5
VCC_2 NC_67
K2 F5
VDDF_2 NC_66
K1
G3 F3 K9
VDDF_4 NC_68
K3 J10
VCC_3 NC_68
K3 J10
VDDF_3 NC_67
K2
AR8105 0 RFU_9 NC_45 NC_69
K12 K9
VCC_4 NC_69
K12 K9
VDDF_4 NC_68
K3
G10 F12 NC_70
K13 NC_70
K13
NC_69
K12
RFU_10 NC_46 C2
VDDI NC_71
K14 NC_71
K14
NC_70
K13
H5 F13 NC_72
L1 C2
VDDI NC_72
L1 C2
VDDI NC_71
K14
DS NC_47 NC_73
L2 NC_73
L2
NC_72
L1
J5 F14 C4
VSS_1 NC_74
L3 NC_74
L3
NC_73
L2
C8107 VSS_5 NC_48 N2
VSS_2 NC_75
L12 E7
VSS_2 NC_75
L12 C4
VSS_1 NC_74
L3
OPT 10pF K6 G1 N5
VSS_3 NC_76
L13 G5
VSS_3 NC_76
L13 N2
VSS_2 NC_75
L12
RFU_13 NC_49 P4
VSS_4 NC_77
L14 H10
VSS_4 NC_77
L14 N5
VSS_3 NC_76
L13
50V K7 G2 P6
VSS_5 NC_78
M1 K8
VSS_6 NC_78
M1 P4
VSS_4 NC_77
L14
RFU_14 NC_50 A6
VSS_6 NC_79
M2 C4
VSSQ_1 NC_79
M2 P6
VSS_5 NC_78
M1
EMMC_STRB K10 G12 E7
VSS_7 NC_80
M3 N2
VSSQ_2 NC_80
M3 A6
VSS_6 NC_79
M2
RFU_15 NC_51 G5
VSS_8 NC_81
M7 N5
VSSQ_3 NC_81
M7 E7
VSS_7 NC_80
M3
P7 G13 H10 M8 P4 M8 G5 M7
R8103
VSS_9 NC_82 VSSQ_4 NC_82 VSS_8 NC_81

RFU_16 NC_52 J5
VSS_10 NC_83
M9 P6
VSSQ_5 NC_83
M9 H10
VSS_9 NC_82
M8
P10 G14 M10
10K
K8 M10 NC_84 J5 M9
VSS_11 NC_84 VSS_10 NC_83
RFU_17 NC_53 NC_85
M11 NC_85
M11 K8
VSS_11 NC_84
M10
H1 NC_86
M12 NC_86
M12
NC_85
M11
A1 M13
NC_54 EMMC_STRB A1
NC_1 NC_87
M13
NC_1 NC_87 NC_86
M12
H2 A2
NC_2 NC_88
M14 A2
NC_2 NC_88
M14 A1
NC_1 NC_87
M13
A8 N1
NC_55 A8
NC_3 NC_89
N1
NC_3 NC_89 A2
NC_2 NC_88
M14
K5 H3 A9
NC_4 NC_90
N3 A9
NC_4 NC_90
N3 A8
NC_3 NC_89
N1
RSTN NC_56 A10
NC_5 NC_91
N6 A10
NC_5 NC_91
N6 A9
NC_4 NC_90
N3
H12 A11 N7 A11
NC_6 NC_92
N7 A10 N6
C8100 DVDD18_EMMC NC_57 A12
NC_6 NC_92
N8 A12
NC_7 NC_93
N8 A11
NC_5 NC_91
N7
NC_7 NC_93 NC_6 NC_92
OPT 0.1uF H13 A13
NC_8 NC_94
N9 A13
NC_8 NC_94
N9 A12
NC_7 NC_93
N8
A14 N10
NC_58 A14
NC_9 NC_95
N10
NC_9 NC_95 A13
NC_8 NC_94
N9
16V C6 H14 B1
NC_10 NC_96
N11 B1
NC_10 NC_96
N11 A14
NC_9 NC_95
N10
N12
VCCQ_1 NC_59 B7
NC_11 NC_97
N12 B7
NC_11 NC_97 B1
NC_10 NC_96
N11
3.3V_EMMC M4 J1 B8
NC_12 NC_98
N13 B8
NC_12 NC_98
N13 B7
NC_11 NC_97
N12
N14
VCCQ_2 NC_60 B9
NC_13 NC_99
N14 B9
NC_13 NC_99 B8
NC_12 NC_98
N13
N4 J2 B10
NC_14 NC_100
P1 B10
NC_14 NC_100
P1 B9
NC_13 NC_99
N14
P2
VCCQ_3 NC_61 B11
EMMC_TOSHIBA
B11 P2 NC_101 B10 P1

NC_15 NC_101 NC_15 NC_14 NC_100
P3 J3 B12
NC_16 RFU_12
P7 B12
NC_16 NC_102
P8 B11
NC_15 NC_101
P2
P9
VCCQ_4 NC_62 B13
NC_17 NC_102
P8 B13
NC_17 NC_103 B12
NC_16 NC_102
P8
P5 J12 B14
NC_18 NC_103
P9 B14
NC_18 NC_104
P11 B13
NC_17 NC_103
P9
P12
VCCQ_5 NC_63 C1 P11 C1
NC_19 NC_105 B14 P11
EMMC_DATA[3]
EMMC_DATA[4]
EMMC_DATA[5]
DAT6
EMMC_CLK_BALL
EMMC_CMD_BALL
EMMC_RESET_BALL
NC_19 NC_104 NC_18 NC_104

OPT OPT J13 C3
NC_20 NC_105
P12 C3
NC_20 NC_106
P13 C1
NC_19 NC_105
P12
C8108 C8109 C8105 C8106 NC_64 C5
NC_21 NC_106
P13 C7
NC_22 NC_107
P14 C3
NC_20 NC_106
P13
0.1uF 2.2uF 0.1uF 2.2uF J14 EMMC_RESET_BALL NC_107

P14 C5
NC_21 NC_107
P14
NC_65
16V 10V 16V 10V E6 K1
VCC_1 NC_66
F5 K2
VCC_2 NC_67
J10 K3
VCC_3 NC_68
K9 K12
VCC_4 NC_69
K13
NC_70
EMMC_VDDI K14
NC_71
C2 L1
VDDI NC_72
OPT L2
C8101 C8104 NC_73
1uF 2.2uF L3
NC_74
25V 10V E7 L12
VSS_2 NC_75
G5 L13
VSS_3 NC_76
H10 L14
VSS_4 NC_77
OPT K8 M1
VSS_6 NC_78
C8102 C8103 C8111 C4 M2
0.1uF 2.2uF 4.7uF VSSQ_1 NC_79
N2 M3 EMMC_CLK_BALL
16V 10V 10V VSSQ_2 NC_80
N5 M7
VSSQ_3 NC_81
P4 M8
VSSQ_4 NC_82
P6 M9
VSSQ_5 NC_83
M10
NC_84
M11
NC_85
M12
NC_86
A1 M13
EMMC_DATA[3] NC_1 NC_87
A2 M14
EMMC_DATA[4] NC_2 NC_88
A8 N1
DAT7 NC_3 NC_89
A9 N3 EMMC_CMD_BALL
NC_4 NC_90
A10 N6
NC_5 NC_91
A11 N7
NC_6 NC_92
A12 N8
NC_7 NC_93
A13 N9
NC_8 NC_94
A14 N10
NC_9 NC_95
B1 N11
NC_10 NC_96
B7 N12
NC_11 NC_97
B8 N13
NC_12 NC_98
B9 N14
DAT6 NC_13 NC_99
B10 P1
NC_14 NC_100
B11 P2
NC_15 NC_101
B12 P8
Dont Connect Power At VDDI EMMC_VDDI DVDD18_EMMC B13
B14
NC_16
NC_17
NC_102
NC_103
P9
P11
NC_18 NC_104
C1 P12
(Just Interal LDO Capacitor) EMMC_DATA[5]
C3
NC_19
NC_20
NC_105
NC_106
P13
C7 P14
NC_22 NC_107

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. eMMC 81
RS-232C Control INTERFACE
+3.5V_ST
Closed to Jack side
AR11200
RS232C
100
1/16W
RS232C
C11204
DOUT1
RS232C
IC11200
0.1uF RIN1
EAF61630102
EAF61630102
MAX3232CDR
VA11200
VA11201
OPT
OPT
C1+ VCC
RS232C 1 16
C11200
0.1uF V+ GND
RS232C 2 15
C11201
0.1uF C1- DOUT1
3 14
C2+ RIN1
RS232C 4 13
C11202
0.1uF C2- ROUT1
5 12 SOC_RX
V- DIN1
RS232C 6 11
SOC_TX
C11203
0.1uF DOUT2 DIN2
7 10
RIN2 ROUT2
8 9
EAN41348201

RS232C 22
TROUBLE SHOOTING GUIDE
Contents of Standard Repair Process
No. Error symptom (High category) Error symptom (Mid category) Page Remarks
1 No video/Normal audio 1
2 No video/No audio 2
3 A. Video error Picture broken/ Freezing 3
4 Color error 4
Vertical/Horizontal bar, residual image,

5 5
light spot, external device color error
6 No power 6
B. Power error Off when on, off while viewing, power
7 7
auto on/off
8 No audio/Normal video 8
C. Audio error
9 Wrecked audio/discontinuation/noise 9
Remote control & Local switch
10 10
checking
MR15 operating checking 11 Not used

11
D. Function error
12 Wifi operating checking 12
13 Camera operating checking 13 Not used
14 External device recognition error 14
15 E. Noise Circuit noise, mechanical noise 15
16 F. Exterior error Exterior defect 16

First of all, Check whether there is SVC Bulletin in GCSC System for these model.
Standard Repair Process
Established
Error A. Video error date
LCD TV symptom
No video/ Normal audio Revised date 1/16
First of all, Check whether all of cables between board is inserted properly or not.
(Main B/D Power B/D, VX1 Cable, Speaker Cable, IR B/D Cable,,,)
A1 A18
No video Normal Y Check Back Light Y Check Power Normal Y Replace T-con/Main
Normal audio On Board or module
audio On with naked eye Board +13V voltage
And Adjust VCOM
N N N
Move to No
A18 Panel Vcc (12V) output Repair Power
video/No audio Board or parts
Replace Inverter
Normal Y
or module
voltage
End
N
Repair Power
Board or parts
Precaution A4 & A2
Always check & record S/W Version and White
Replace Main Board Re-enter White Balance value
Balance value before replacing the Main Board
1
Established
symptom
No video/ No audio Revised date 2/16
A18
Check various Check and
Normal Y
No Video/ voltages of Power replace
No audio Board ( 13V) voltage?
MAIN B/D
N End
Replace Power
Board and repair
parts
2
Established
symptom
Picture broken/ Freezing Revised date 3/16
. By using Digital signal level meter

A3
. By using Diagnostics menu on OSD
Check RF Signal level ( All Settings Channels Channel Tuning Manual Tuning Signal Strength, Signal Quality)
- Signal strength (Normal : over 50%)
- Signal Quality (Normal: over 50%)
Y Check whether other equipments have problem or not.

Normal
(By connecting RF Cable at other equipment)
Signal?
DVD Player ,Set-Top-Box, Different maker TV etc`
N
A4
Check RF Cable
Normal Y Check SVC N Check Y
Connection Close
1. Reconnection Picture? S/W Version Bulletin? Tuner soldering
2. Install Booster N
Y
N
S/W Upgrade
N Contact with signal distributor
Normal
Picture? or broadcaster (Cable or Air)
Normal N
Y Picture? Replace
Main B/D
Y
Close
Close
3
Established
symptom
Color error Revised date 4/16
A6 A7
Check Y
Check color by input
and replace
-External Input Y Y
Color Link Cable Color Color
-COMPONENT Replace Main B/D Replace module
error? (V by one) error? error?
-AV
and contact
-HDMI N N N
condition
Check error End

color input
mode
A8 Check
External Input/ External device Y
external
Check Test pattern Component /Cable Replace Main/T-con B/D
device and
error normal
cable
N
Request repair
for external
device/cable
Check external External device Y

HDMI device and /Cable Replace Main/T-con B/D
error cable normal
4
A. Video error Established

Error date
symptom Vertical / Horizontal bar, residual image,
light spot, external device color error Revised date 5/16
Vertical/Horizontal bar, residual image, light spot Replace

Module
A6
A7 N
Check color condition by input Check external
Check and
-External Input Screen Y device Y Screen N Screen
-Component Normal? replace Link Replace Main/T-con B/D
normal? connection normal? (adjust VCOM) normal?
-HDMI Cable
condition
N N For LGD panel Y
Y
Replace Main B/D
Replace Request repair End End
for external
A8 module
device
Check Test pattern
For other panel
External device screen error-Color error

Check screen
condition by input
-External Input External
Check S/W Version Check N
-Component Input Connect other external N
version
-HDMI error device and cable Screen Replace
(Check normal operation of normal? Main/T-con
Y External Input, Component, B/D
Component and HDMI by connecting
error Y
S/W Upgrade Jig, pattern Generator ,Set-
top Box etc.
Request repair for
external device
Y
Connect other external
Normal N HDMI/
device and cable N
screen? DVI Screen Replace
(Check normal operation of
External Input, Component, normal? Main /T-con
Y and HDMI by connecting Jig, B/D
pattern Generator ,Set-top
Box etc.
End
5
Established
Error B. Power error date
symptom
No power Revised date 6/16
A17 A18
DC Power on Replace
Check Power LED Y Normal N Check Power Y
by pressing Power Key OK? Power
Logo LED On? operation? On High
On Remote control B/D
. Stand-By: Red or Turn On
N Y
. Operating: Turn Off
Check Power cord Replace Main B/D
was inserted properly
A18
N Measure voltage of each output of Power B/D
Normal?
Y
Y Y
Normal
voltage?
Replace Main B/D
Close Normal
Check ST-BY 3.5V
Y
voltage? N
A18 Replace Power B/D
N
Replace Power
B/D
6
Established
Error B. Power error date
symptom
Off when on, off while viewing, power auto on/off Revised date 7/16
Check outlet
A19
N Y
Check A/C cord Error? Check Power Off CPU Normal? End
Replace Main B/D
Mode Abnormal
N
Check for all 3- phase
power out Y Abnormal Replace Power B/D
1
Fix A/C cord & Outlet A18

and check each 3
(If Power Off mode
phase out
is not displayed) Normal Y
Replace Main B/D
Check Power B/D voltage?
voltage
N
Caution
Check and fix exterior Replace Power B/D
of Power B/D Part
* Please refer to the all cases which Status Power off List Explanation
"POWEROFF_Remote KEY" Power off by Remote CONTROL
can be displayed on power off mode.
"POWEROFF_OFFTIMER" Power off by OFF TIMER
"POWEROFF_SLEEPTIMER" Power off by SLEEP TIMER
"POWEROFF_INSTOP" Power off by INSTOP KEY
"POWEROFF_AUTOOFF" Power off by AUTO OFF
Normal "POWEROFF_ONTIMER" Power off by ON TIMER
"POWEROFF_RS232C" Power off by RS232C
"POWEROFF_RESREC" Power off by Reservated Record
"POWEROFF_RECEND" Power off by End of Recording
"POWEROFF_SWDOWN" Power off by S/W Download
"POWEROFF_UNKNOWN" Power off by unknown status except listed case
"POWEROFF_ABNORMAL1" Power off by abnormal status except CPU trouble
Abnormal
"POWEROFF_CPUABNORMAL" Power off by CPU Abnormal
7
Established
Error C. Audio error date
symptom
No audio/ Normal video Revised date 8/16
A20 A21+A18
Check user N Check audio B+ Y
No audio Normal
menu > Off A13V of Power
Screen normal voltage
Speaker off Board
Y N
Cancel OFF Replace Power Board and repair parts
Check N
Disconnection Replace MAIN Board End
Speaker
disconnection
Y
Replace Speaker
8
Established
Error C. Audio error date
symptom
Wrecked audio/ discontinuation/noise Revised date 9/16
abnormal audio/discontinuation/noise is same after Check input signal compared to No audio
Wrecked audio/
A21+A18
Check and replace
Discontinuation/ Check audio
speaker and
Noise for B+ Voltage (A13V)
connector
Check input all audio
signal Y Y
Signal
-RF
normal? Wrecked audio/
-External Input Normal
signal Discontinuation/
N Replace Main B/D voltage?
Noise only
for D-TV
N
Wrecked audio/
Discontinuation/
Replace Power B/D
Noise only
for Analog
(When RF signal is not
received)
Request repair to external Wrecked audio/ Replace Main B/D End
cable/ANT provider Discontinuation/
Noise only
for External Input
(In case of N
External Input Connect and check Normal
signal error) other external audio?
Check and fix device
external device Y
Check and fix external device
9
D. Function error Established

Error date
symptom
Remote control & Local switch checking Revised date 10/16
1. Remote control(R/C) operating error Replace

Main B/D
A22 A22 A22
Check & Repair N Check B+ Y Y
Check R/C itself Normal Y Normal Normal Check IR Normal
operating? Cable connection operating? 3.5V Voltage? Signal?
Operation Output signal
Connector solder On Main B/D
N
Y N N
A18
Check R/C Operating Check & Replace Close Check 3.5v on Power B/D Repair/Replace
When turn off light Baterry of R/C Replace Power B/D or IR B/D
in room Replace Main B/D
(Power B/D dont have problem)
If R/C operate, Normal Y
operating? Close
Explain the customer
cause is interference
from light in room. N
Replace R/C
10

Error date
symptom
MR13 operating checking Revised date 11/16
2. MR15(Magic Remocon) operating error (UH61 Model doesn`t support Magic Remocon)
A4
Check the N Check MR15
RF Receiver ver Normal Y Press the Is show ok N Turn off/on the
INSTART menu is 00.00? itself Operation operating? set and press
wheel message?
the wheel
N
Y
Y
A23
Check & Replace Close
Check & Repair Battery of MR15
RF assy
connection
Normal Y
A4 operating? Close
Is show ok N Press the back
RF Receiver ver N message? key about 5sec
Close N
is 00.00?
Y
Replace
MR13
Y Close
Down load the Firmware

* If you conduct the loop at 3times, change the M4.
* INSTART MENU14.RF
Remocon Test3. Firmware
download
11

Error date
symptom
Wifi operating checking Revised date 12/16
3.Wifi operating error
A4 A24
Check the Wi-Fi Mac value N Check the Wifi wafer Normal N Replace
INSTART menu is NG? Voltage?
1pin Main B/D
Y
A24 Y
Check & Repair Close

Wifi cable
connection
A4
Wi-Fi Mac value N
is NG? Close
Change the Wifi

assy
12

Error date
symptom
Camera operating checking Revised date 13/16
4.Camera operating error (Camera operation is not support)
A4 A25
Check the Camera Ver. N Reconnect the Normal N Replace
INSTART menu is NULL? operation?
Camera module Main B/D
Y
Y
Close
Change the
Camera module
13
Established
Error D. Function error date
symptom
External device recognition error Revised date 14/16
Y Check technical
Check External Input and
Signal information Technical N
input Component Replace Main B/D
input? - Fix information information?
Recognition error
signal
- S/W Version
N Y
HDMI/
Check and fix DVI, Optical
Fix in Replace Main B/D
external device/cable Recognition error
accordance
with technical
information
14
Established
Error E. Noise date
symptom
Circuit noise, mechanical noise Revised date 15/16
Identify Check
Circuit
nose location of Replace PSU
noise
type noise
Mechanical Check location of

noise noise
When the nose is severe, replace the module

Mechanical noise is a natural (For models with fix information, upgrade the
phenomenon, and apply the 1st level S/W or provide the description)
description. When the customer does not OR
agree, apply the process by stage. If there is a Tak Tak noise from the
Describe the basis of the description cabinet, refer to the KMS fix information and
in Part related to nose in the Owners then proceed as shown in the solution manual
Manual. (For models without any fix information,
provide the description)
15
Established
Error F. Exterior defect date
symptom
Exterior defect Revised date 16/16
Zoom part with Module

Replace module
exterior damage damage
Cabinet
Replace cabinet
damage
Remote
control Replace Remote control
damage
Stand
Replace stand
dent
16
Contents of Standard Repair Process Detail Technical Manual
No. Error symptom Content Page Remarks

1 A. Video error_ No video/Normal Check LCD back light with naked eye A1
2 audio Check White Balance value A2
TUNER input signal strength checking

3 A3
method
A. Video error_ video error /Video
4 lag/stop Version checking method A4
5 Tuner Checking Part A5
A. Video error _Vertical/Horizontal bar,
6 Connection diagram A6
residual image, light spot
7 Check Link Cable reconnection condition A7

A. Video error_ Color error
8 Adjustment Test pattern - ADJ Key A8
9 Exchange Main Board (1) A-1/5
10 Exchange Main Board (2) A-2/5
<Appendix>
11 Defected Type caused by T-Con/ Exchange Power Board (PSU) A-3/5
Inverter/ Module
12 Exchange Module (1) A-4/5
13 Exchange Module (2) A-5/5
Contents of Standard Repair Process Detail Technical Manual
No. Error symptom Content Page Remarks

14 Check front display LED A17
B. Power error_ No power
15 Check power input Voltage & ST-BY 3.5V A18
B. Power error_Off when on, off
16 POWER OFF MODE checking method A19
while viewing
Checking method in menu when there is
17 A20
C. Audio error_ No audio/Normal no audio
video Voltage and speaker checking method
18 A21
when there is no audio
Remote control operation checking
19 A22
method
Motion Remote operation checking
20 D. Function error A23 Not Used
method
21 Wifi operation checking method A24
22 Camera operation checking method A25 Not Used
23 E. Etc Tool option changing method A26
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_No video/Normal audio date
Revised
Content Check LCD back light with naked eye A1
date
<49UH6100>
After turning on the power and disassembling the case, check with the naked eye,
whether you can see light from locations.
A1
Error Established
symptom A. Video error_No video/Normal audio date
Revised
Content Check White Balance value A2
date
<ALL MODELS>
Entry
Entrymethod
method
1.1.Press
Pressthe
theADJ
ADJbutton
buttonononthe
theRemote
Remotecontrolfor adjustment.
control for adjustment.
2.2.Enter
Enterinto
intoWhite
WhiteBalance
Balanceofofitem
item6.13.
3.3.After
Afterrecording
recordingthe
theR,R,G,G,B B(GAIN,
(GAIN,Cut)
Cut)value
valueofofColor
ColorTemp
Temp
(Cool/Medium/Warm),
(Cool/Medium/Warm),re-enterre-enterthe
thevalue
valueafter
afterreplacing
replacingthe
theMAIN
MAINBOARD.
BOARD.
A2
Error Established
symptom A. Video error_Video error, video lag/stop date
TUNER input signal strength checking method Revised
Content date A3
<ALL MODELS>
Advanced Channels Channel Tuning

Manual Tuning
When the signal is strong,

use the attenuator (-10dB, -
15dB, -20dB etc.)
A3
Error Established
symptom A. Video error_Video error, video lag/stop date
Version checking method Revised
Content date A4
<ALL MODELS> 1. Checking method for Remote control for adjustment
Version
Press the IN-START with the

Remote control for adjustment
A4
Error Established
symptom
A. Video error_Video error, video lag/stop
date
Revised
Content TUNER checking part A5
date
<ALL MODELS>
Checking method:
1. Check the signal strength or check whether the screen is normal when the external device is connected.
2. After measuring each voltage from power supply, finally replace the MAIN BOARD.
3. If you can`t see the UHD live TV, please connect signal at left side of jack. (Korea model only)
A5
Error A. Video error _Vertical/Horizontal bar, Established
symptom residual image, light spot date
Revised
Content connection diagram (1) date A6
<ALL MODELS>
As the part connecting to the external input, check

the screen condition by signal
A6
Error Established
symptom A. Video error_Color error date
Revised
Content Check Link Cable(VX1) reconnection condition date A7
<ALL MODELS>
Check the contact condition of the Link Cable, especially dust or mis insertion.
A7
Error Established
symptom
A. Video error_Color error
date
Adjustment Test pattern - ADJ Key Revised
Content date A8
You can view 6 types of patterns using the ADJ Key
Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..)
4.Video error (Classification of MODULE or Main-B/D!)
A8
Appendix : Exchange Main Board (1)
Solder defect, CNT Broken Solder defect, CNT Broken Solder defect, CNT Broken
Solder defect, CNT Broken T-Con

T-Con Defect,
Defect,
Solder
T-Con CNT
CNT
defect,CNT
Defect, Broken
Broken
CNTBroken
Broken Abnormal Power Section
Solder defect, Short/Crack Abnormal Power Section Solder defect, Short/Crack
A - 1/5
Appendix : Exchange Main Board (2)
Abnormal Power Section Abnormal Power Section Solder defect, Short/Crack
Solder defect, Short/Crack Fuse Open, Abnormal power section Abnormal Display
GRADATION Noise GRADATION
A - 2/5
Appendix : Exchange Power Board (PSU)
No Light Dim Light
Dim Light Dim Light
No picture/Sound Ok
A - 3/5
Appendix : Exchange the Module (1)
Panel Mura, Light leakage Panel Mura, Light leakage Press damage
Crosstalk Press damage Crosstalk
Un-repairable Cases
In this case please exchange the module.
Press damage
A - 4/5
Appendix : Exchange the Module (2)
Vertical Block Vertical Line Vertical Block

Source TAB IC Defect Source TAB IC Defect Source TAB IC Defect
Horizontal
TAB ICBlock
Horizontal Block Horizontal line
Gate Defect Gate TAB IC Defect
Gate TAB IC Defect Gate TAB IC Defect Gate TAB IC Defect
Un-repairable Cases
In this case please exchange the module.
Horizontal Block
Gate TAB IC Defect
Gate TAB IC Defect
A - 5/5
Error Established
symptom B. Power error _No power date
Revised
Content Check front Power Indicator date A17
<49UH61>
Joystick button
ST-BY condition: On or Off

Power ON condition: Turn Off
North America model doesn`t use lum.sensor
A17
Error Established
symptom
B. Power error _No power
date
Revised
Content Check power input voltage and ST-BY 3.5V A18
date
Check the DC 13.2V
A18
Error
symptom B. Power error _Off when on, off whiling viewing Established
date
Revised
Content POWER OFF MODE checking method date A19
<ALL MODELS>
Entry method
1. Press the IN-START button of the Remote

control for adjustment
2. Check the entry into adjustment item 3
A19
Error Established
symptom C. Audio error_No audio/Normal video
date
Revised
Content Checking method in menu when there is no audio date A20
<ALL MODELS>
Checking method
1. Press the Setting button on the Remote control
2. Select the Sound function of the Menu
3. Select the Sound Out
4. Select TV Speaker
A20
Error Established
symptom C. Audio error_No audio/Normal video date
Voltage and speaker checking method Revised
Content date A21
when there is no audio
<49UH6100-UH>
1 SPK_R-
2 SPK_R+
Checking order when there is no audio 3 SPK_L-
4 SPK_L+
1.Check the contact condition of or 13V connector of Main Board
2. Measure the 13V input voltage supplied from Power Board

(If there is no input voltage, remove and check the connector)
3.Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you touch the
GND and output terminal, the speaker is normal.
A21
Error Established
symptom D. Function error date
Revised
Content Remote control operation checking method date A22
<49UH6100-UH>
1 +3.5V_WIFI
2 WIFI_DM_JACK
IR & Control Key front 3 WIFI_DP_JACK
4 GND
5 WOL/WIFI_POWER_ON_JACK
6 GND
7 M-Moudle_RESET
8 GND
IR & Control Key Rear 12 EYE_SDA

13 EYE_SCL
14 GND
15 IR
16 LED_R_JACK
17 GND
18 +3.5V_ST
19 KEY2_JACK
IR 20 GND
21 GND
Checking order to check Remote control
Checking order
1.Check IR cable condition between IR & Main board.( Check picture number and )
2.Check the standby 3.5V on the terminal 18 pin ()
3.AS checking the Pre-Amp(IR LED light) , the power is in ON condition, an Analog Tester
needle should move slowly, otherwise, its defective.
A22
Error Established
symptom D. Function error date
Revised
Content Remote controloperation checking method date A22
< 49UH6100-UH>
1 +3.5V_WIFI
Wifi Front 2 WIFI_DM_JACK
3 WIFI_DP_JACK
4 GND
5 WOL/WIFI_POWER_ON_JACK
6 GND
7 M-Moudle_RESET
8 GND
12 EYE_SDA
13 EYE_SCL
Wifi Rear 14 GND
15 IR
16 LED_R_JACK
17 GND
18 +3.5V_ST
19 KEY2_JACK
20 GND
21 GND
Checking order to check wifi

Checking order
1.Check BT/Wifi cable condition between BT/Wifi assy & Main board.
2.Check the 3.5V on the terminal 1 (+3.5V_WIFI)
A23/A24

LG 55UH615 Chassis UA65R

Uploaded by

Copyright:

Available Formats

LG 55UH615 Chassis UA65R

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LG 55UH615 Chassis UA65R

Uploaded by

Copyright:

Available Formats

Internal Use Only

MODEL : 55UH615* 55UH615*-U*

P/NO : MFL69413320 (1602-REV00)

SAFETY PRECAUTIONS ......................................................................... 3

SERVICING PRECAUTIONS .................................................................... 4

EXPLODED VIEW ................................................................................... 34

SCHEMATIC CIRCUIT DIAGRAM ............................................ APPENDIX

TROUBLE SHOOTING GUIDE ................................................. APPENDIX

IMPORTANT SAFETY NOTICE

General Guidance Leakage Current Hot Check (See below Figure)

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed

Leakage Current Cold Check(Antenna Cold Check)

Fuse and Conventional Resistor

1. Application range 3. Test method

(1) Temperature : 25 C 5 C(779F), CST : 40 C5 C

5.1.2. HDMI Input (PC/DTV)

No. Resolution H-freq(kHz) V-freq.(kHz) Pixel clock(MHz) Proposed

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock VIC 3D input proposed Proposed

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock Proposed 3D input proposed mode

5.2.3. HDMI-PC Input (3D) (3D Supported Mode Manually)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock Proposed 3D input proposed mode

5.2.5. RF Input (3D supported mode automatically)

No. Signal 3D input proposed mode

5.2.6. USB, DLNA (Movie) Input (3D supported mode manually)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) 3D input proposed mode

5.2.7. USB, DLNA (Photo) Input (3D supported mode manually)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) 3D input proposed mode

5.2.8. USB, DNLA Input (3D supported mode automatically)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) 3D input proposed mode

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

5.2.10. Miracast, Widi (3D supported mode manually)

**Remark: 3D Input mode

In case of keeping module is in the circumstance of 0C, it

3. Adjustment items Source change xb 00 40

3.2. Final assembly adjustment Confirm adj. ad 00 99 NG 03 00x (Fail)

3.3. Etc. Adj. order

4.2.2. Communication Port connection

4.2.3. Download process

4.3.3. LAN PORT INSPECTION (PING TEST)

(1) Play the LAN Port Test PROGRAM.

a. Press the INSTART key of ADJ remote controller.

d. Check the model name INSTART menu -> Factory name

4.5. WIFI MAC ADDRESS CHECK

Method & Notice

A. Serial number D/L is using of scan equipment.

/ DDC (Display Data Channel) download 0x03

5.2.3. Download method

EDID Block 1, Bytes 128-255 EDID Block 1, Bytes 128-255

(1) RS-232C Command used during auto-adj.

5.4.3. Equipment connection MAP

Pat t ern Generat o r

* If TV internal pattern is used, not needed

Probe RS -232C G Gain j b 00 C0 TBD

Pat t ern Generat o r G Cut TBD

- LEN: Number of Data Byte to be sent 5.5.5. Adjustment method

Standard color coordinate and temperature using CA-210

5.8. 3D function test

5.10. EYE-Q Green Function Inspection

MODEL : 55UH615* 55UH615-U

In case of keeping module is in the circumstance of 0C, it

d. Check the model name INSTART menu -> Factory name

Standard color coordinate and temperature using CA-210