This document provides specifications for a single band twin beam antenna, including its electrical specifications, mechanical specifications, remote electrical tilt information, packaging details, regulatory compliance, and included mounting kit. The antenna supports two beams at ±27 degrees from boresight and has integrated internal remote electrical tilt control.
This document provides specifications for a single band twin beam antenna, including its electrical specifications, mechanical specifications, remote electrical tilt information, packaging details, regulatory compliance, and included mounting kit. The antenna supports two beams at ±27 degrees from boresight and has integrated internal remote electrical tilt control.
This document provides specifications for a single band twin beam antenna, including its electrical specifications, mechanical specifications, remote electrical tilt information, packaging details, regulatory compliance, and included mounting kit. The antenna supports two beams at ±27 degrees from boresight and has integrated internal remote electrical tilt control.
This document provides specifications for a single band twin beam antenna, including its electrical specifications, mechanical specifications, remote electrical tilt information, packaging details, regulatory compliance, and included mounting kit. The antenna supports two beams at ±27 degrees from boresight and has integrated internal remote electrical tilt control.
Single Band Twin Beam Antenna, 824960 MHz, 38 horizontal beamwidth, internal electrical tilt with manual override. l
Single panel design supporting two separate beams perfectly optimized at horizontal pointing angles of +27 degrees and 27 degrees from boresight
Integrated Internal Remote Electrical Tilt (RET), with independent control of electrical tilt with manual override on all arrays
Electrical Specifications Frequency Band, MHz Gain, dBi Beam Centers, Horizontal, degrees Beamwidth, Horizontal, degrees Beamwidth, Vertical, degrees Beam Tilt, degrees USLS (First Lobe), dB Front-to-Back Ratio at 180, dB Isolation, Same Beam, dB VSWR | Return Loss, dB PIM, 3rd Order, 2 x 20 W, dBc Input Power per Port, maximum, watts Polarization Impedance
824890 18.0 27 39 9.8 010 18 25 25
890960 18.5 27 36 9.1 010 18 25 25
1.3 | 17.7
1.3 | 17.7
-150 500 45 50 ohm
-150 500 45 50 ohm
Electrical Specifications, BASTA*
Frequency Band, MHz Gain by all Beam Tilts, average, dBi Gain by all Beam Tilts Tolerance, dB Gain by Beam Tilt, average, dBi Beamwidth, Horizontal Tolerance, degrees Beamwidth, Vertical Tolerance, degrees USLS, beampeak to 20 above beampeak, dB Front-to-Back Total Power at 180 30, dB CPR at Boresight, dB CPR at Sector, dB
824890 17.9 0.3
890960 18.2 0.3
0 | 17.9
0 | 18.2
5 | 18.0
5 | 18.2
10 | 17.9
10 | 18.0
1.7 0.3 18 22 21 22
1.7 0.3 18 19 22 22
* CommScope supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the whitepaper Time to Raise the Bar on BSAs.
General Specifications Operating Frequency Band
824 960 MHz
Antenna Type
Multibeam
Band
Single band
Performance Note
Outdoor usage
2016CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: December 1, 2016
page 1 of 3 December 12, 2016
Product Specifications 2CPX208R 2CPX208R--V1
Mechanical Specifications RF Connector Quantity, total
RF Connector Quantity, low band
RF Connector Interface
7-16 DIN Female
Color
Light gray
Grounding Type
RF connector inner conductor and body grounded to reflector and
mounting bracket
Radome Material
Polyester fiberglass pultrusion
Reflector Material
Aluminum
RF Connector Location
Bottom
Wind Loading, frontal
1339.0 N @ 150 km/h
301.0 lbf @ 150 km/h
Wind Loading, lateral
172.0 N @ 150 km/h
38.7 lbf @ 150 km/h
Wind Loading, rear
1350.0 N @ 150 km/h
303.5 lbf @ 150 km/h
Wind Speed, maximum
200 km/h
124 mph
Dimensions Length
2090.0 mm
Width
504.0 mm
Depth
118.0 mm | 4.6 in
Net Weight, without mounting kit
32.5 kg
| |
82.3 in 19.8 in
71.7 lb
Remote Electrical Tilt (RET) Information
Input Voltage
1030 Vdc
Internal RET
Low band (2)
Power Consumption, idle state, maximum
2.0 W
Power Consumption, normal conditions, maximum 13.0 W
Protocol
3GPP/AISG 2.0 (Single RET)
RET Interface
8-pin DIN Male
RET Interface, quantity
1 male
Packed Dimensions Length
2229.0 mm
Width
593.0 mm
Depth
209.0 mm | 8.2 in
Shipping Weight
45.5 kg
| |
87.8 in 23.3 in
100.3 lb
Regulatory Compliance/Certifications Agency RoHS 2011/65/EU China RoHS SJ/T 11364-2006 ISO 9001:2008
Classification Compliant by Exemption Above Maximum Concentration Value (MCV) Designed, manufactured and/or distributed under this quality management system
2016CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: December 1, 2016
page 2 of 3 December 12, 2016
Product Specifications 2CPX208R 2CPX208R--V1
Included Products T-029-GL-E
Adjustable Tilt Pipe Mounting Kit for 2.0"-4.5" (50-115mm) OD round members for panel antennas. Includes
2 clamp sets.
* Footnotes Performance Note
Severe environmental conditions may degrade optimum performance
2016CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: December 1, 2016
