Alarm Eaglemaster E8-LCD (ENG)
Alarm Eaglemaster E8-LCD (ENG)
Alarm Eaglemaster E8-LCD (ENG)
W I T H R E M O T E E N G I N E S TA R T
MODEL
E8
IMPORTANT:
Please read the entire manual for complete details on the features, accessories and
operation before attempting to use your security system.
This Security system must be installed by a qualified technician to ensure proper
operation. Do not attempt to install or modify this system yourself as
this way void your warranty.
What is included:
A control module
Tranceiver module
One 5-button 2-way LCD remote transmitter
One 4-button random code remote transmitter
Dual stage shock sensor
High output 6-tone siren (optional)
Full set wire harness
Pin switches
*Many require additional parts and/or labor, see store for details
NOTE:
Some of the features described in this manual may required additional parts and/or
labor, and may not be included as part of the standard installation of this unit.
Additionally, many features of this security system have selectable options that must be
activated or programmed during the system's installation. These items will be identified
in the following sections. Please discuss these features and any questions you may
regarding the installation of this product with your authorized dealer.
Fig.1
System Armed.
System Disarmed.
Silent Armed.
Zone1
1st-stage sensor bypass.
Zone1
2nd-stage sensor bypass.
Zone2
1st-stage sensor bypass.
Zone2
2nd-stage sensor bypass.
Panic mode.
Zone1
1st stage sensor triggered.
Zone2
1st stage sensor triggered.
Zone1
2nd stage sensor triggered.
Zone2
1st stage sensor triggered.
Immobilizer mode.
Battery conservemode.
Valet mode.
Turbo mode.
Vibrate mode.
Functions
Step
Condition
Press
once
Press
Press
Press
Press
Press
ACC ON
Press
once
Armed
Press
Armed
Press
Engine running
Press
Press
over 2sec.
over 2sec.
Engine running
Press
Press
Functions
Trunk open / CH-1 active
Step
Press
Condition
Press
Press
once
Press
Silent armed
Press
Valet mode
Press
Panic mode
Press
ACC OFF
Anti-Hi-Jack mode
Press
ACC ON
Press
once
Press
CH-2 active
Press
CH-3 active
Press
CH-4 active
Press
Functions
Step
Condition
Press
Press
Press
Press
Press
Bend the top part of the cover a bit, move it up and remove,
Remove the discharged battery,
Place the new battery (AAA) observing polarity,
Carefully place the cover back.
4. Press and hold the Valet button, you will hear the siren start chirping (from 1~3 chirp),
while give 2 chirp sound, immediately release the Valet button.
5. The LED will start flashing to acknowledging that the system is ready for programming of
new transmitters.
6. Press any button of the first transmitter, you will hear 1-short chirp acknowledging that
the first transmitter has been programmed
Press any button of the second transmitter, you will hear 2-short chirp acknowledging
that the second transmitter has been programmed.
Repeat the operation 3 for other transmitters.
7. To exit the transmitter programming mode, Turn on the ignition and you will hear two long
siren chirps.
for over 2sec. the 2-way remote will respond tone & vibrate feature,
pressing 2sec. will change the feature, see under table:
Vibrations
1-time
1-time
- With in 5 minutes, the 2-way remote will than give 1 beep sound every one minute for 5
cycles to remind the user within range.
- After 5 minutes, the 2-way remote will than give 1 beep sound every 25 minutes to remind
the user within range.
Note: If under Check-in range mode, if alarm triggered, this function will automatically
turn off (disable).
24-hour display
Minutes display
3. Press button
to turn up the numbers. Press button
to turn down the numbers.
The button may be held down to scroll faster.
4. Press button
to exit the setting mode. 2 beep will be heard.
Note: The remote will revert to normal operation from the set mode when 10-seconds has
elapsed without a button entry.
Command Page
When a command (arm/disarm, remote start , or auxiliary channel) from the remote
control is sent and received, the system will send a command page back to confirm receipt.
Note: When the system is in Valet mode, the remote control will show the lock icon and
unlock icon, but will not generate a command page.
Alarm Page
If the alarm system is triggered while armed, an Alarm Page will be sent to the remote
control. When the remote receives an Alarm Page, the LCD icons will display the alarm
system status information and the remote control will generate beeps.
Display
Beeps
5 short
Vibrations
1 times
Trigger
Zone 1
1st stage-Sensor warning
Zone 1
2nd stage-Sensor triggering
5 short
Zone2
1st stage-Sensor warning
1 times
Zone 2
2nd stage-Sensor triggering
Ignition triggering
Standard features
- To ARM the system: Press the button
once.
To arm your system within proper operation range, simply press button
once (while
system in disarmed or Acc off position) . The system will respond one siren chirp, one lights
flash, doors lock, disable engine starter, the status LED will flash approximately once per
second, indicating that the system is actively protecting your vehicle.
IMMO icon
indicate that
the engine
blocked
Defective zone
Siren chirps
2-way beeps
Door opened
4 chirps
1 long + 3 short
Trunk opened
5 chirps
1 long + 4 short
Hood opened
6 chirps
1 long + 5 short
Icon flashing
indicator
Note: If during the operating of the passive arming timer if a door is being opened the
Operating of the passive arming timer will be suspended. As soon as all doors, hood
and trunk are closed the system will start the cycle of the passive arming again. As
soon as 30 seconds are over the armed mode will be turned On.
Icon flashing
indicator
- Alarm cycle :
If a violation occurs the system will respond by sounding the siren and flashing the lights for
approximately 30sec. before the system resets itself and continues to protect your car. If
violation still occurs the system, siren and lights will working for 4 or 5 cycles then the
system reset itself and continues to protect other zones.
- Zone-1 / Zone-2 : 2nd stage sensor triggering limited for 4 cycles
- Door / Hood / Trunk zone triggering limited for 5 cycles
over 2sec.
To temporarily turn off the arm or disarm chirps, use Silent mode. Simply press the button
1+2 over 2sec.. The system will armed without siren chirp. Disarm the system the siren will
be automatically returned into the normal mode.
Note: The Zone1 and Zone 2 sensors are bypassed if the system is armed using Silent
Mode. This ensures that no chirps will be emitted by the siren in an area you want chirp-free.
The system is still fully capableof triggering. Only the sensor is bypassed.
for
Zone1: 2nd-stage
sensor triggered
Zone2: 2nd-stage
sensor triggered
Zone2: 1st-stage
sensor triggered
Note: Before the ignition turn on, you may realized again which zone been triggered by
Press
button (status check) once, the LCD will display triggered zone again.
-Heavy impact will activate the 2nd stage sensor and trigger the alarm for 20sec. 2-way
remote will respond melody and flashing icon as under.
Zone 1 -2nd stage
e sensor trigger
NOTE: Adjustments are made via the rotary control above the shock sensor.
Valet mode
I f you are going to have your vehicle serviced, parked by a valet or washed you will want to
put your security system Into valet mode. To enter valet mode as follows:
With Valet button:
1. Disarm the system .
2. Turn the ignition from on to off.
3. Within 10 sec after switching off the ignition press and hold the Valet button over 3 sec ,
the LED starts flashing , release the Valet button.
4. Press and hold the Valet button, you will hear siren chirp (from 1 to 3 chirp sound), while
give 1 chirp sound, immediately release the Valet button. You will automatically at Valet
mode, the LED steady ON .
With remote:
1. Turn the ignition to ON status.
2. Press the button
for over 2sec. until the status LED steady ON.
Note:
Under Valet mode, each time
turn Acc off , the siren will give
2 chirps for notification.
When the system is in the valet mode it can not be armed. The door lock and unlock will
function as keyless entry system.
To exit valet mode:
Turn Ignition switch to ON position , then press button
for over 2seconds. You
will hear siren provide 2 long and LED light OFF to confirm exit this mode and in alarm mode.
The 2-Way remote will respond 1 long and 2 short beeps.
Flash icon if
engine started.
Shutdown input :
While the vehicle is running during remote start operation, the system will monitor the
vehicle and will automatically shut down the engine if the system receives any of the
following shutdown inputs:
- The brake pedal is pressed.
- The hood is opened.
- The hand brake switch off / Park switch gear off position.
- The pre-programmed run time (10, 20, or 30 minutes) has elapsed.
- Press the button
over 2sec.
) hour.
Turn on to indicate
Fix time start enable
over 2sec.
2. Press button
to select Hour & Min adjust setting. Icon flashing to indicate.
3. Press button
to turn up the numbers. Press button
to turn down the numbers.
The button may be held down to scroll faster.
4. Press button
to enable clock time. 1 beep will be heard and exit the mode.
Press button
to disable clock time. 2 beep will be heard and exit the mode.
Note: The remote will revert to normal operation from the set mode when 10-seconds has
elapsed without a button entry.
Exit the Clock time engine start mode:
1. press the button
over 2sec. then press again the button
over 2sec.
2 beep sound will be heard and clock icon flashing.
2. Press button
to disable clock time. 2 beep will be heard and exit the mode.
- Safety mode :
Arming the system the 2way remote will turn on the safety mode icon
, it will allow to
engine start if the icon is turn on. If one of the zone's been triggered, the icon will turn off
and engine start is not available . It will able to engine start by next arming again.
over 2sec.
- Safety mode for manual-type car: Press the button
This safety feature for the car with manual-gear type (Table-3 of NO 4), before set the
engine start mode, you have to set the system in Safety mode.
To set safety mode:
1. In safe status, Engine running , press the button
for over 2sec.
2. The parking lights will active to indicate in safety mode.
3. Remove the ignition key, and leave the car , however the engine still running.
4. Arm the system, and the 2-way LCD will indicate Safety icon as under:
Icon on if the
safety mode active.
Icon flashing
indicator
Anti-Hi-Jack mode
This feature will protect your vehicle in the event that there is an attempt to Hi-jack the
vehicle. The system allows using three independent or simultaneous options to turn on the
function Anti-Hi-Jack.
If the system turned on Anti-hI-Jack mode, the parking lights will flash 1 time and the LED
will start flashing fast indicate that the mode is turned on.
Flashing normally
Flashing
1 flash
Warning chirp
Siren turn on
Siren
Engine circuit
Timer
0sec.
50sec.
60sec.
90sec.
Note. If the CH1 channel output is enable when the system was in the armed mode the
system will simultaneously turn off the shock sensor and the trunk trigger. As soon as the
trunk is closed the system will automatically re-arm the circuit and turn the shock sensor on.
Note: (1) Ignition ON does not allow to remote trunk open.
(2) Armed, if trunk keep opened over 1 minutes, the 2-way remote will give pre-warn
beep sound.
. Control of the CH-1 (Remote latched) - Press the button
over 2sec.
Simply press and hold button 4 over 2 seconds, the channel will constant output .
To exit by press and hold button 4 over 2 seconds, the channel will deactivated.
. Control of the CH-1 (programming time output with sensor off /on) Press the button
over 2sec.
Simply press and hold button 4 over 2 seconds, the channel will constant output for the preprogrammed period of time or until press the button 4 over 2 seconds.
The sensor zones can be turn off or on status , during the channel activated, check Table-2
of NO.5.
If programmed , the channel will constant output 30sec. when disarming. This feature
for the car with dome-light supervision.
. Control of the CH-2 (Remote latched) - Press the button
over 2sec.
Simply press and hold button 1+4 over 2 seconds, the channel will constant output .
To exit by press and hold button 1+4 over 2 seconds, the channel will deactivated.
. Control of the CH-2 (programming time output with sensor off /on) Press the button
over 2sec.
Simply press and hold button 1+4 over 2 seconds, the channel will constant output for the
pre-programmed period of time or until press the button 1+4 over 2 seconds.
The sensor zones can be turn off or on status , during the channel activated, check Table-2
of NO.6.
If programmed , the channel will constant output 30sec. when arming. This feature for
the car with window closing after arming.
. Control of the CH-3 (Remote latched) - Press the button
over 2sec.
Simply press and hold button 2+4 over 2 seconds, the channel will constant output .
To exit by press and hold button 2+4 over 2 seconds, the channel will deactivated.
. Control of the CH-2 (programming time output with sensor off /on) Press the button
over 2sec.
Simply press and hold button 2+4 over 2 seconds, the channel will constant output for the
pre-programmed period of time or until press the button 2+4 over 2 seconds.
The sensor zones can be turn off or on status , during the channel activated, check Table-2
of NO.7.
. Control of the CH-4 (programming time output with sensor off /on) Press the button
over 2sec.
Simply press and hold button 3+4 over 2 seconds, the channel will constant output for the
pre-programmed period of time or until press the button 3+4 over 2 seconds.
The sensor zones can be turn off or on status , during the channel activated, check Table-2
of NO.8.
LED
indicator
LED
indicator
4. Press and hold the Valet button, you will hear siren chirp (from 1 to 3 chirp sound),
while give 3 chirp sound, immediately release the Valet button.
You will automatically at the PIN code setting mode. Siren will give 1 long chirp sound.
5. If Table-1 of NO.6 set in " Valet SW status" , follow the step #9.
If Table-1 of NO.6 set in "PIN code status", follow the next step #6
6. Enter the first digit of the code with the Valet button (the number of pressing the Valet
button corresponds to one digit of the code);
Press remote button 1 once to confirm the first code, by given 1 chirp sound.
7. Enter the second digit of the code with the Valet button (the number of pressing the
Valet button corresponds to the second digit of the code);
Press remote button 1 once to confirm the second code, by given 2 chirp sound.
8. If PIN code correct insert , the siren will give 1 long chirp to acknowledging that the
system is ready for programming of new PIN code, see next step #9.
If PIN code incorrect insert, the system will exit the mode by given 2-long chirp.
<< Suppose that you want set new PIN code is 3.8 >>
9. To programme the 1st PIN code by press the Valet button the number of times
corresponding to the 1st digit of your PIN code. Press 3 times of the Valet button,
(each time the Valet button is pressing, the status LED will activated) .
10. Press the remote button 1 once, siren will give 1 chirp to confirm the 1st digit code .
11. To programme the 2nd PIN code by press the Valet button the number of times
corresponding to the 2nd digit of your PIN code. Press 8 times of the Valet button,
(each time the Valet button is pressing, the status LED will activated) .
12. Press the remote button 1 once, siren will give 2 chirp to confirm the 2nd digit code .
13. Wait a second, the status LED will notify the 2 digit PIN code, by 3 flashes - pause - 8
flashes.
14. If you wish to change the new PIN code again, press and hols the Valet button until
transceiver give 1 long beep, to indicate that you can programme again from above
step 9 .
15. To Exit the mode, turn ignition to ON , and you will hear two long siren chirps.
You must write down or remember your PIN code.
Note:
Please notice that the time between your actions shall be less than 20 sec; otherwise the
system will automatically exit the programming mode and you will hear two long siren chirps.
PROGRAMME TABLE-1
Press the
Valet SW
to next item
Item NO. by
LED flash
Press button
Press button
Press button
Press button
1-chirp
2-chirp
3-chirp
4-chirp
PROGRAMME
FEATURES
No.1
No.2
Passive arming
No.3
Passive immobilizer
No.4
Automatically Rearming
No.5
Anti-Hi-Jack mode
No.6
Emergency disarm by :
Valet Switch / Pin code
No.7
No.8
No.9
Factory settings
OFF
ON
OFF
OFF
ON
With door
locking
OFF
OFF
ON
ON
OFF
OFF
ON
With door
locking
OFF
ON
ON
ON
ON
By Door SW
Activate
By ignition
turn on
By remote
activate
OFF
OFF
ON
ON
ON
ON
OFF
OFF
2minutes
PROGRAMME TABLE-2
Press the
Valet SW
to next item
Item NO. by
LED flash
Press button
Press button
Press button
1-chirp
2-chirp
3-chirp
4-chirp
0.8 sec.
3.5 sec.
Lock0.8sec.
Unlock2pulse
Lock30sec.
Unlock0.8sec.
5 sec.
15 sec.
45 sec.
60 sec.
PROGRAMME
FEATURES
No.1
No.2
No.3
No.4
Press button
Interlock
N/C Type
Interlock
N/C Type
Interlock
N/O Type
Interlock
N/O Type
Armed output
Armed output
Disarmed
output
Disarmed
output
OFF
OFF
ON
ON
Trunk open
Pulse output
1sec
Remote
latched
by key-1
No.5
No.6
No.7
No.8
Disarming
Pulse
output
30sec
Programme Programme
time output time output
1~120sec.
1~120sec.
sensor on
sensor off
Programme Programme
Remote
time output time output
latched
1~120sec.
by key-1+4 1~120sec.
sensor on
sensor off
Programme Programme
Remote
Arming
time output time output
latched
Pulse output
1~120sec.
by key-2+4 1~120sec.
30sec
sensor off
sensor on
2nd stage
unlock
Programme
Remote
time output
latched
by key-3+4 1~120sec.
sensor off
Programme
time output
1~120sec.
sensor on
PROGRAMME TABLE-3
Press the
Valet SW
to next item
Press button
Press button
Press button
Press button
1-chirp
2-chirp
3-chirp
4-chirp
PROGRAMME
FEATURES
Item NO. by
LED flash
Unlimited
No.1
No.2
2 hour
3 hour
4 hour
24 hour
No.3
-5 C
- 10 C
- 15 C
- 25 C
No.4
Auto
type
Auto
type
Manual
type
Manual
type
No.5
No.6
No.7
0.8 sec.
1.4 sec.
2 sec.
3.6 sec.
No.8
Petrol
(Delay2sec.)
Diesel
(Delay4sec.)
Diesel
(Delay6sec.)
Diesel
(Delay10sec.)
No.9
Voltage
"noise"
Tacho
sensor
Generator Generator
(+)
(-)
if
No.10
Zone1&Zone2 triggered
No.11
No.12
press
Factory settings
button to disarm
OFF
OFF
Zone1
Zone2
Zone1+2
2nd stage 2nd stage 2nd stage
Triggered triggered triggered
OFF
Zone1
Bypass
Zone2
Bypass
Zone1+2
Bypass
OFF
Delay
10sec.
ON
ON
System Installation:
1. Thoroughly read and become familiar with the installation instructions before
beginning the installation.
2. Review system contents: (1). A control module. (2).2-way pager transceiver antenna
(3). One 5-button 2-way LCD remote transmitter.
(4).One 3-button random code remote transmitter
(5).Dual stage shock sensor (6).High output 6-tone siren (optional)
(7).Harness:
. 24-Pin main harness . 4-pin x2 shock sensor harness.
. 7-pin transceiver harness . 3-Pin (40a) block relay harness
3. Verify with the owner, the mounting location for all visible components, including the
LED and Valet/over-ride switch.
4. Verify with the owner, the optional programme features.
5. Inspect and perform a function test for all vehicle systems before and after the
installation.
6. Always use a Volt / Ohm meter for testing vehicle circuits. Never use a test light.
7. Always look before drilling any holes or mounting self-tapping screws. Be sure fuel
lines and exterior wiring looms are clear as they often close to the chassis and difficult
to see.
8. Protect all wires running from the engine compartment to the interior of the vehicle by
covering with electrical tape and split loom tubing. Be sure to use a grommet when
routing wires through the firewall.
9. Properly fuse any additional accessories such as window module, trunk opener, etc.,
making sure to power them separate from the alarm module. This will ensure the
functionality system in the event of an accessory failure.
WIRING DIAGRAM :
Green
Blue
Black
Red
Dual-stage/zone
Shock Sensor
Antenna
Extend the whole wire, align it with the intersection
of dashboard and the front window glass.
Keep it away from the metal at least 5 cm to have
the best receiving condition.
ZONE1
Plug-in dual stage
shock sensor
ZONE2
External
Ultra sonic &
micro-wave
sensor port
LED
indicator
LED
indicator
Push button
Call switch
External
Temperature
Sensor
E8
Use external temperature
sensor for measurement of
engine temperature or
temperature in the given
point of car compartment.
Install the sensor in nearby
engine .
20-PIN CON2
Main connector
wiring
6-PIN CON3
Connector
for door lock
wiring
6-PIN CON1
Connector
for Engine start
wiring
10
(-) CH-6
Connect to Chassis
Ground (-)
20
11
Yellow
Black
Connect to (-)
negative Hood
pin switch
Pink
Red/black
Green/white
Gray
Blue/white
Connect to (-)
negative Trunk
pin switch
Connect to
Existing (+)
Positive
Door Switch
Connect to
Existing (-)
Negative
Door Switch
Blue
White
Purple
Gray/black
White
Green
Brown
White/red
Yellow/black
Orange
Black/white
IGN1 output(+)
the wire will active
when remote start
and engine running
Yellow
Black/yellow
Positive power
(+) 12VDC input
Yellow/black
blue
6
30A
red
Green
Green
Green/black
Blue/red
Blue/black
Blue
(+)12V DC
(-) When Armed
Red
Green
Black
Blue
Black/white
original bypass
output
SENSOR TRIGGER
OUTPUT
CUT
Yellow/black (-)
factory disarm output
(+)12V
To disarm (-)
wire
(+)12V
To disarm (+)
wire
(+)12V
11
10
20
White/red wire
1.0 uf/250V
To Tachometer sensor
+ 12V
STOP lamps
MOTOR CONTROL
DOWN
UP
MAIN LINE
+ 12V
2 WIRE ACTUATOR
Green/black
Green
Green/red
Blue/black
Blue
Blue/red
LOCK MOTOR
UNLOCK MOTOR
(-)GND
3.) A built-in Central door lock with electric lock switch( like: CHRYSLER.. )
+ 12V
DOWN
ELECTRIC
MOTOR
MOTOR LOCK
INSIDE THE
FRONT DOOR
UP
4.) For vacuum type central door lock system ( like : Mercedes Benz , AUDI.. )
Green/black
Green
Green/red
Blue/black
Blue
Blue/red
+ 12V
ELECTRIC
MOTOR
DOWN
AIR COMPRESSOR
UP
Made in Taiwan