RugerPrecisionRifle Bp2dZ95h4Rs7

S
PM605
INSTRUCTION
MANUAL
FOR
RUGER
PRECISION RIFLE
TM
Rugged, Reliable Firearms

READ THE INSTRUCTIONS AND
WARNINGS IN THIS MANUAL CAREFULLY
BEFORE USING THIS FIREARM
2015 Sturm, Ruger & Co., Inc.
This manual may not be reproduced in whole or in part without the express written
permission of Sturm, Ruger & Co., Inc.
For Service on This Model Please Call:

(603) 865-2442 (See p. 46)
THIS INSTRUCTION MANUAL SHOULD ALWAYS ACCOMPANY THIS FIREARM AND BE
TRANSFERRED WITH IT UPON CHANGE OF OWNERSHIP, OR WHEN THE FIREARM IS LOANED
OR PRESENTED TO ANOTHER PERSON
www.ruger.com
TAC 7/15
State-By-State Warnings
Certain states require by law that their own specified warning

notices in larger-than-normal type be conspicuously included by
the manufacturer, distributor or retailer with firearms sold in that
state. Sturm, Ruger & Co., Inc. sells its products in compliance
with applicable laws and regulations. Because our products may
be sold in these states, we include the following:
California:
WARNING
ADVERTENCIA
A los nios los atraen las armas
de fuego y las pueden hacer
funcionar. Ellos pueden causarses
lesions graves y la muerte. Evite
que los nios tengan accesso a las
armas de fuego guardndolas
siempre con llave y descargadas
cuando no las est utilizando. Si
usted tiene un arma de fuego
cargada en un lugar en que un
nio tiene acceso a ella y la usa
indebidamente, le pueden dar una
multa o enviarlo a la carcel.
Children are attracted to and

can operate firearms that can
cause severe injuries or death.
Prevent child access by always
keeping guns locked away and
unloaded when not in use. If you
keep a loaded firearm where a
child obtains and improperly uses
it, you may be fined or sent to
prison.
Connecticut:
UNLAWFUL STORAGE OF A LOADED FIREARM MAY

RESULT IN IMPRISONMENT OR FINE.
Florida:
IT IS UNLAWFUL, AND PUNISHABLE BY

IMPRISONMENT AND FINE, FOR ANY ADULT TO
STORE OR LEAVE A FIREARM IN ANY PLACE WITHIN
THE REACH OR EASY ACCESS OF A MINOR UNDER 18
YEARS OF AGE OR TO KNOWINGLY SELL OR
OTHERWISE TRANSFER OWNERSHIP OR POSSESSION
OF A FIREARM TO A MINOR OR A PERSON OF
UNSOUND MIND.
2
Maine:
ENDANGERING THE WELFARE OF A CHILD IS A

CRIME. IF YOU LEAVE A FIREARM AND AMMUNITION
WITHIN EASY ACCESS OF A CHILD, YOU MAY BE
SUBJECT TO FINE, IMPRISONMENT OR BOTH. KEEP
FIREARMS AND AMMUNITION SEPARATE. KEEP
FIREARMS AND AMMUNITION LOCKED UP. USE
TRIGGER LOCKS.
Maryland:
WARNING: Children can operate firearms which may cause

death or serious injury. It is a crime to store or leave a loaded
firearm in any location where an individual knew or should
have known that an unsupervised minor would gain access to
the firearm. Store your firearm responsibly!
Massachusetts:
WARNING FROM THE MASSACHUSETTS ATTORNEY

GENERAL: This handgun is not equipped with a device that
fully blocks use by unauthorized users. More than 200,000
firearms like this one are stolen from their owners every year
in the United States. In addition, there are more than a
thousand suicides each year by younger children and
teenagers who get access to firearms. Hundreds more die from
accidental discharge. It is likely that many more children
sustain serious wounds, or inflict such wounds accidentally on
others. In order to limit the chance of such misuse, it is
imperative that you keep this weapon locked in a secure place
and take other steps necessary to limit the possibility of theft
or accident. Failure to take reasonable preventive steps may
result in innocent lives being lost, and in some circumstances
may result in your liability for these deaths.
IT IS UNLAWFUL TO STORE OR KEEP A FIREARM,
RIFLE, SHOTGUN OR MACHINE GUN IN ANY PLACE
UNLESS THAT WEAPON IS EQUIPPED WITH A
TAMPER-RESISTANT SAFETY DEVICE OR IS STORED
OR KEPT IN A SECURELY LOCKED CONTAINER.
3
New Jersey:
IT IS A CRIMINAL OFFENSE TO LEAVE A LOADED

FIREARM WITHIN EASY ACCESS OF A MINOR.
New York City:
THE USE OF A LOCKING DEVICE OR SAFETY LOCK IS

ONLY ONE ASPECT OF RESPONSIBLE FIREARM
STORAGE. FOR INCREASED SAFETY, FIREARMS
SHOULD BE STORED UNLOADED AND LOCKED IN A
LOCATION THAT IS BOTH SEPARATE FROM THEIR
AMMUNITION AND INACCESSIBLE TO CHILDREN AND
UNAUTHORIZED PERSONS.
North Carolina:
IT IS UNLAWFUL TO STORE OR LEAVE A FIREARM

THAT CAN BE DISCHARGED IN A MANNER THAT A
REASONABLE PERSON SHOULD KNOW IS ACCESSIBLE
TO A MINOR.
Texas:
IT IS UNLAWFUL TO STORE, TRANSPORT, OR

ABANDON AN UNSECURED FIREARM IN A PLACE
WHERE CHILDREN ARE LIKELY TO BE AND CAN
OBTAIN ACCESS TO THE FIREARM.
Wisconsin:
IF YOU LEAVE A LOADED FIREARM WITHIN THE

REACH OR EASY ACCESS OF A CHILD YOU MAY BE
FINED OR IMPRISONED OR BOTH IF THE CHILD
IMPROPERLY DISCHARGES, POSSESSES, OR EXHIBITS
THE FIREARM.
* * * * * * * * * * * * * * * * * * * * * *
Please check with your licensed retailer or state police for
additional warnings which may be required by local law or
regulation. Such regulations change constantly, and local
authorities are in the best position to advise you on such legal
matters.
4
FIREARMS SAFETY IS YOUR RESPONSIBILITY

SAFETY MUST BE THE FIRST AND CONSTANT
CONSIDERATION OF EVERY PERSON WHO HANDLES
FIREARMS AND AMMUNITION.
This Instruction Manual is designed to assist you in learning how to
properly use and care for your RUGER PRECISION RIFLE.
Please contact us if you have any questions.
Only when you are certain you fully understand the manual and can
properly carry out its instructions should you practice loading, unloading,
etc. with live ammunition. If you have any doubts about your ability to
handle or use a particular type of gun safely, you should seek supervised
instruction. Such personalized instruction often is available from local
gun retailers, gun clubs or police departments. If none of these sources
can help, visit www.nra.org or write to the following address:
National Rifle Association
11250 Waples Mill Road
Fairfax, VA 22030-7400
The person possessing a gun has a full-time job. You cannot guess; you
cannot forget. You must know how to use your firearm safely. Do not use
any firearm without having a complete understanding of its particular
characteristics and safe use. Remember: There is no such thing as a
foolproof gun.
TABLE OF CONTENTS
Page
State-By-State Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Locking Device Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Operation of Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Unboxing Your Rifle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Ammunition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Magazines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Care and Cleaning of Magazine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
To Load and Fire (With Magazine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
To Load and Fire (Without Magazine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
To Unload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
To Clear a Malfunction (Jam) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
To Minimize Malfunctions (Jams) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Stock Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Trigger Pull Weight Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Ruger Precision Rifle Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Lower Receiver Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Reversing the Safety Selector Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Trigger Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
How to Clean the Trigger Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Service and Parts Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Shipping Firearms for Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Exploded Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 - 54
The Basic Rules of Safe Firearms Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
RUGER is a registered U.S. trademark.
WARNINGS OF GREAT IMPORTANCE ARE

FOUND ON THE FOLLOWING PAGES:
Locking Devices
Alterations
Manual Safety
Folding Stock
Ammunition
Lead Exposure
Loading
Handling
7
9
11
13
14
15
19
19
Unloading
Malfunctions
Folding Stock
Disassembly
Lubrication
Storage
Shipping
Parts Purchasers
OTHER CAUTIONS AND WARNINGS APPEAR

THROUGHOUT THE MANUAL.
21
22
23
34
43
45
46
47
LOCKING DEVICE
INSTALLATION INSTRUCTIONS
WARNING USE OF LOCKING DEVICES
Always keep your firearm pointed in a safe direction,
including when you are installing or removing your
locking device.
Always verify that your firearm is completely unloaded

before installing your locking device.
Do not install locking devices in the trigger guard;

always keep your fingers and locking device outside the
trigger guard during device installation and removal.
Store firearms, ammunition and keys separately and

securely, away from children and careless adults; do not
store your firearm with the keys in the locking device.
Do not attempt to work the action of your firearm with
the locking device in place; this may damage your
firearm.
Do not store keys

in lock.
While locking devices are an important aid to security

measures, they are not a substitute for safe firearm
handling and proper storage. Remember that any
mechanical device can be bypassed with enough time,
knowledge, determination and equipment.
LOCKING DEVICES MUST BE USED

SAFELY AND RESPONSIBLY
It is important to use the locking device on your Ruger firearm!
Keep the muzzle pointed in a safe direction and your fingers outside the
trigger guard at all times!
To Install the Factory-Supplied Locking Device:
1. Be sure the firearm and its magazine are completely unloaded and
contain no cartridges or cartridge cases.
3. Remove the magazine by pressing the magazine release lever (just
behind the magazine and in front of the trigger guard see
nomenclature, p. 10) forward, and pulling the magazine down and out
of the rifle.
2. Open the action completely by drawing the bolt fully to the rear.
4. If the stock is unfolded, fold the stock so the bolt can be removed (see
page 23).
7
5. If the bolt is in the upper receiver, remove the bolt by lifting the bolt
handle upward, and then pulling the bolt rearward while depressing
the rear portion of the bolt stop. (See step 7, page 35.)
6. Apply the lock to your RUGER PRECISION RIFLE as shown
below in Figure 1.
7. With the key turned to the farthest clockwise position, insert the
loose end of the cable into the lock. Turn the key counterclockwise
and remove the key.
8. Once the lock is securely closed, pull firmly on the lock to test the
connection and be sure it is locked. Do not leave or store your
firearm with the key in the lock! Store your locked, unloaded firearm
and the key in secure, separate locations, away from ammunition,
children and unauthorized adults.
Figure 1
Correct Installation of Cable Lock

For Ruger Precision Rifle
FIREARMS ARE DANGEROUS WEAPONS

READ THE INSTRUCTIONS AND WARNINGS
IN THIS MANUAL THOROUGHLY AND CAREFULLY
BEFORE USING.
WARNINGALTERATIONS
This product was designed to
function properly in its original
condition. Alterations can make it
unsafe. Do not alter any part or add
or substitute parts or accessories not
made by Sturm, Ruger & Co., Inc.
DO NOT ALTER ANY GUN
GENERAL INFORMATION
AND MECHANICAL CHARACTERISTICS
The RUGER PRECISION RIFLE is a bolt-action, magazine fed,
repeating rifle. The assembly of the RUGER PRECISION RIFLE is
designed to produce a direct recoil path through the upper receiver into the butt
stock, without the use of traditional bedding. Materials used in the RUGER
PRECISION RIFLE are steel and aircraft grade aluminum. Styling and
features of the RUGER PRECISION RIFLE have been carefully crafted
to accommodate Ruger and other aftermarket accessories designed for use on
modern sporting-type rifles.
Notable features of the RUGER PRECISION RIFLE include: a new
externally adjustable trigger; a magazine latching system that accepts two
different magazine types: (1) M110/SR25/DPMS/Magpul, and (2) AICS; a folding
stock with adjustment for length of pull and comb height; and a 20 MOA canted
scope base.
NOMENCLATURE
BUTT STOCK
CHEEK PIECE
CANTED
SCOPE BASE
UPPER
RECEIVER
BARREL
LOWER RECEIVER
BUTT PAD
ADJUSTMENT
CAM LEVERS
MAGAZINE
BOLT HANDLE
Figure 2
BOLT STOP
SAFETY
SELECTOR
SWITCH
HANDGUARD
MAGAZINE
RELEASE
LEVER
TRIGGER
BUTT PAD
STOCK
RELEASE BUTTON
PISTOL GRIP
Figure 3 In these illustrations the frequently used operating components are identified.
OPERATION OF SAFETY
The manual safety mechanism on the RUGER PRECISION RIFLE is
located on the left side of the lower receiver rearward of the trigger. The safety
selector switch can be moved from the FIRE position to the SAFE position
only when the firing pin is cocked. (Fully raising the bolt handle cocks the firing
pin.) The safety selector switch is on when it is in a fully horizontal position
pointing to the word SAFE. (See Figure 4, p. 11.) When the safety is on
SAFE, it blocks the trigger. The FIRE position is reached by rotating the lever
towards a vertical position. The lever will stop when the pointer reaches the word
FIRE.
10
WARNING: When manipulating the safety selector switch, KEEP YOUR

FINGERS OUTSIDE THE TRIGGER GUARD! When the safety selector switch is
in the FIRE position and the trigger is pulled, the rifle will fire.
The safety should be kept on SAFE at all times except when actually firing.
If the safety selector switch does not function properly, or it seems to move too
easily, or it does not seem firmly positioned in either the SAFE or FIRE
position, the rifle should not be used. It should be returned to the Newport
Customer Service Department for repair (see page 46).
SAFETY ON
SAFETY OFF
(ready to fire)
Figure 4
WARNING MANUAL SAFETY
Safety in "SAFE"
Position
Keep the safety selector switch in the SAFE

position unless actually firing. Always move
the safety selector switch fully to its intended
position and check it. The safety selector
switch must be rotated fully to the SAFE
position for the safety to be on. Never depend
on a safety mechanism or any other
mechanical device to justify careless handling
or permitting the rifle to point in an unsafe
direction. The only safe rifle is one in which
the bolt is open, the chamber is empty, and
there is no magazine in the gun.
KNOW HOW TO USE THE SAFETY
11
UNBOXING YOUR RIFLE

General Contents
IMPORTANT NOTICE
WHEN ORIGINALLY SHIPPED FROM THE FACTORY, YOUR
RUGER PRECISION RIFLE BOX, AND CONTENTS, WERE IN
PERFECT CONDITION TO ENSURE SAFE DELIVERY.
IF THIS BOX IS USED FOR RESHIPMENT OF THE ORIGINAL
CONTENTS, IT SHOULD BE REINFORCED AND HANDLED
CAREFULLY TO PREVENT DAMAGE IN TRANSIT.
RUGER PRECISION RIFLE
CABLE LOCK
MAGAZINES
RIFLE ACCESSORIES
BOLT
1. Keep the muzzle pointed in a safe direction and

your fingers outside the trigger guard at all times!
2. Lift butt stock (rotate 90 upward). See Figure 5.
3. Grasp the butt pad and lift the rifle until it
emerges from its nested cavity in the packaging.
At this point, keep the butt stock folded so the
bolt can be inserted into the receiver.
Figure 5
4. Be sure the firearm and its magazine are completely unloaded and contain no
cartridges or cartridge cases! At this point, no magazine should be in the
rifle.
5. Reference Operation of Safety section, p. 10. Rotate the safety selector
switch to its full horizontal position with the pointer facing the word SAFE.
If you do not plan to utilize your firearm immediately, Ruger recommends
applying the locking device to the rifle. Please see Locking Device
Installation Instructions, p. 7. If you will be using the rifle, please continue
to step 6.
12
6. Remove the rifle bolt from

its nested cavity and insert
it into the upper receiver
as shown in Figure 6.
In order to insert the bolt
into the upper receiver, the
bolt handle must be at the
two ooclock position and
the lobe of the cocking
piece must be in the six
oclock position. If this is
not the case, grasp the
entire bolt shroud firmly
and rotate it clockwise
until the lobe and handle
are in the correct positions
(see Figure 7). Tilt the rifle so
the muzzle end faces
downward (in a safe direction)
to aid in this process. The bolt
handle must be oriented
towards the bolt channel on
the right hand side of the
upper receiver.
Figure 6
Figure 7
BOLT HANDLE AT
2 OCLOCK POSITION
LOBE OF COCKING PIECE
AT 6 OCLOCK POSITION
7. Continue to run the bolt to its forwardmost position, then rotate the bolt handle
down to lock the bolt closed. Please note that the bolt must be in its forwardmost
position and not protruding from the back of the upper receiver before the stock
is closed. Closing the stock with the bolt protruding from the upper receiver can
result in damage to your rifle.
WARNING FOLDING STOCK

The bolt on your Ruger
Precision Rifle should always
be in the forwardmost and
locked (handle down) position
when folding or opening the
stock. Failure to fully close the
bolt may result in damage to
the bolt shroud or bolt.
CLOSE BOLT
BEFORE FOLDING
OR OPENING STOCK
13
8. Unfold the butt stock until it aligns with the upper receiver and snaps into
place. An audible click will be heard as the pivot latch engages.
9. Raise the bolt handle and retract the bolt fully.
10. Be sure the firearm and its magazine are completely unloaded and contain
no cartridges or cartridge cases! At this point, no magazine should be in the
rifle.
11. Your rifle is now assembled. Please continue reading this manual to
familiarize yourself with the features and functions of your RUGER
PRECISION RIFLE.
AMMUNITION
The RUGER PRECISION RIFLE is chambered for many of the most
popular factory-loaded cartridges manufactured in accordance with U.S. Industry
practice. The particular caliber for each rifle is marked on the barrel. Use
cartridges only of the designated caliber marked on the barrel. Please see
Warning - Ammunition below and Warning - Loading on page 19.
USE ONLY FACTORY AMMUNITION LOADED

TO U.S. INDUSTRY STANDARDS
WARNING AMMUNITION
Death, serious injury and damage
can result from the wrong
ammunition, bore obstructions,
powder overloads or incorrect
cartridge components. Even the
strongest gun can be blown up as
a result of excess pressure. Always
wear shooting glasses and hearing
protection.
IMPROPER AMMUNITION
DESTROYS GUNS
AMMUNITION (CARTRIDGES) NOTICE

WE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR ANY DAMAGE OR
INJURY WHATSOEVER OCCURRING IN CONNECTION WITH, OR AS
THE RESULT OF, THE USE IN RUGER FIREARMS OF FAULTY, OR
NON-STANDARD, OR REMANUFACTURED OR HAND LOADED
(RELOADED) AMMUNITION, OR OF CARTRIDGES OTHER THAN
THOSE FOR WHICH THE FIREARM WAS ORIGINALLY CHAMBERED.
14
WARNING LEAD EXPOSURE

Discharging firearms in poorly ventilated
areas, cleaning firearms, or handling
ammunition may result in exposure to
lead and other substances known to the
State of California to cause birth defects,
reproductive harm, and other serious
physical injury. Have adequate ventilation
at all times. Wash hands thoroughly after
exposure.
SHOOTING OR CLEANING GUNS

MAY EXPOSE YOU TO LEAD
MAGAZINES
The RUGER PRECISION RIFLEs patented magazine latching system
accepts two different magazine types: (1) M110/SR25/DPMS/Magpul, and (2)
AICS. Ruger has tested these magazine types and selected the 10-round, Magpul
PMAG 10 LR/SR GEN M3 magazine to ship with this rifle.
The correct caliber for your rifle is marked on the barrel and, although this
magazine is marked 7.62 x 51 you should only load it with cartridges of the correct
caliber for your rifle. As always, Ruger recommends use of only high-quality
magazines that are clean and in good working order.
Magazines that have been tested and approved for use with the RUGER
PRECISION RIFLE are available through our Sportswear & Accessories
Sales Department, Monday through Friday, 7:30 a.m. - 6:00 p.m. EST at 1-888-2201173 ET or 24 hours a day, 7 days a week on the web at www.ShopRuger.com.
Magpul PMAG 10 LR/SR GEN M3
AICS MAGAZINE
DAMAGED, NON-STANDARD OR IMPROPERLY ASSEMBLED

MAGAZINES SHOULD NOT BE USED. THEY CAN CAUSE THE
RIFLE TO MALFUNCTION.
15
INSERTING THE MAGAZINE

Practice the important aspects of gun handling described below (with an
unloaded rifle) until you can perform each of the steps with skill and confidence.
Before loading the rifle, please read completely through this manual and be
certain the muzzle is pointing in a safe direction. Do not load the rifle until you
are ready to use it! The rifle may be loaded with the bolt in the open (fully to the
rear) or closed position, but loading in the open position is the preferred method
because the chamber condition can be readily and continually determined, and it
requires less force to insert a loaded magazine into the rifle with the bolt in the
open (rearward) position.
1. Keep the muzzle pointed in a safe direction (see Rule 2, p. 55).
2. Position the safety selector switch in the SAFE position (see Figure 4, p. 11).
3. Hold the magazine as shown in Figure 8
and insert it all the way up into the
magazine well. An audible click should
be heard and felt as the magazine latch
engages.
4. Check to be sure that the magazine is
securely latched into place by pulling
down on the magazine.
Figure 8
REMOVING THE MAGAZINE

3. Hold the magazine as shown in Figure 9
by gripping the magazine and the
magazine release lever together. Squeeze
the lever towards the magazine to
disengage the latch. As you squeeze the
lever, you will feel it move through two
stages; you may encounter heavier
resistance releasing the second stage.
(This is normal for a side latching
magazine.)
Figure 9
4. Once the magazine release lever has stopped, begin pulling down on the
magazine, allowing your thumb to slide off the lever. To minimize the
possibility of damage and malfunctions, do not let the magazine drop to the
ground.
16
LOADING THE MAGAZINE

Use only clean, dry ammunition of the proper caliber in good condition and
manufactured to U. S. Industry specifications. (See Notice and Warnings in other
sections of this manual pertaining to Ammunition).
With the narrow end of the
magazine facing forward, place a
round between the feed lips of the
magazine with the bullet tip
forward. (See Figure 10.) Press the
round down until it is held by the
feed lips. Be sure to slide the round
reward until it is seated against the
back of the magazine. Place the next
round on top and repeat until the
desired number of cartridges are
loaded or the magazine is fully
loaded.
Figure 10
CARE AND CLEANING OF MAGAZINE

Check the magazine frequently to ensure that the follower moves freely and has
adequate spring tension so that each cartridge is quickly raised to the feeding
position.
To test the spring tension, load one cartridge into the magazine and then firmly
press against the cartridge case. Remove your finger quickly. The cartridge
should instantly and fully move into the feeding position. If it does not, the
magazine should be cleaned. If cleaning does not restore proper spring tension,
do not use the magazine. (NOTE: After testing, remove the test cartridge.)
When cleaning is necessary, use a solvent that will not harm the polymer or
metal components.
TO LOAD AND FIRE (WITH MAGAZINE)

3. Lift the bolt handle and draw the bolt fully to the rear.
4. Insert loaded magazine (see Figure 8, p. 16). Do not chamber a cartridge
until you are ready to shoot.
5. Push the bolt handle forward. This will strip a cartridge from the magazine
and push the cartridge ahead of the bolt into the chamber.
17
6. Close the bolt handle fully downward and keep the safety selector switch in
the SAFE position. If it is desired to top off the magazine, the magazine
may be removed, an additional cartridge loaded into the magazine, and the
magazine inserted back into the rifle.
7. With a cartridge now chambered and the rifle pointed in a safe direction,
rotate the safety selector switch into the FIRE position. Pulling the trigger
will fire the cartridge. Always be certain that you are aware of your backstop
and know where the bullet will strike when you fire the rifle.
8. Once the rifle has discharged, you may cycle the bolt to eject the spent case
and chamber another round for firing.
9. Once the desired number of rounds have been fired, raise the bolt handle and
draw the bolt fully to the rear.
Note that cocking the firing pin by lifting the bolt handle is required to allow
the rifle to enter the SAFE mode.
TO LOAD AND FIRE (WITHOUT MAGAZINE)

3. Lift the bolt handle and draw the bolt fully to the rear.
4. Do not chamber a cartridge until you are ready to shoot. When you are ready
to shoot, place a cartridge directly into the chamber. Push the bolt handle
forward.
5. Close the bolt handle fully downward and keep the safety selector switch in
the SAFE position. An empty, partially loaded, or fully loaded magazine may
then be inserted into the rifle if desired.
6. With a cartridge chambered and the rifle pointed in a safe direction, rotate the
safety selector switch into the FIRE position. Pulling the trigger will fire the
cartridge. Always be certain that you are aware of your backstop and know
where the bullet will strike when you fire the rifle.
7. Once the desired number of rounds have been fired, raise the bolt handle and
draw the bolt fully to the rear. Note that cocking the firing pin by lifting the
bolt handle is required to allow the rifle to enter the SAFE mode.
18
WARNING LOADING
Know the caliber of your rifle you are loading and load
cartridges of only that caliber into it!
Before loading, be certain the primer of each cartridge is seated
flush with, or below, the surface of the cartridge case base. A
cartridge discharged by the closing of the bolt can result in
possible serious injury to the shooter and those nearby.
If a cartridge does not chamber readily, do not force it. Check
the bore and chamber to be certain that each cartridge is the
proper caliber and of correct dimensions. If you cannot
determine why the cartridge will not fit, clear the rifle of all
cartridges and write or call the factory.
The wrong ammunition can destroy your gun and result in
serious injury.
BE SURE WHAT YOU LOAD

IS THE CORRECT CALIBER
WARNING: DO NOT TOUCH THE TRIGGER

UNTIL YOU ARE ACTUALLY READY
TO FIRE THE RIFLE.
WARNING HANDLING
Never carry the rifle loaded with the
safety selector switch in the FIRE
position. If dropped or struck with the
safety off, the rifle may fire. Such a
discharge can occur with or without the
trigger being directly struck or touched.
Never rest a loaded rifle against any
object (wall, fence, vehicle, tree, etc.)
because there is always the possibility
that the rifle will be jarred or slide from
its position and fall with sufficient force
to discharge. Keep the safety on unless
actually firing.
ANY GUN MAY FIRE IF

DROPPED
19
TO UNLOAD
WARNING: This sequence must be followed exactly as spelled out. Failure to do
so can result in the rifles chamber becoming unintentionally loaded with a
cartridge!
1. Keep the muzzle pointed in a safe direction at all times and keep your fingers
outside the trigger guard.
2. Move the safety selector switch to the SAFE position if the firing pin is
cocked (see Figure 4, p. 11).
3. Remove the magazine. REMEMBER that even though the magazine has been
removed, a cartridge remaining in the chamber can still be fired!
4. Raise the bolt handle and draw the bolt fully to the rear, extracting and ejecting
any cartridge in the chamber.
Note that cocking the firing pin by lifting the bolt handle is required to place
the safety selector switch in the SAFE mode.
6. Always visually double check the chamber to be certain it is empty. At this
point, no magazine should be in the rifle.
CORRECT UNLOADING SEQUENCE

1
SAFETY IN
"SAFE" POSITION
20
WARNING UNLOADING
Removing the magazine or removing
cartridges from the magazine does not
prevent the rifle from being fired! When
there is a cartridge in the chamber and the
safety selector switch is in the FIRE
position, the cartridge will discharge if the
trigger is pulled. It is absolutely essential
for the user to know how to completely
unload the rifle. Completely means
emptying the magazine and removing a
chambered cartridge. The safety selector
switch should always be in the SAFE
position when the rifle is being unloaded.
See the Operation of Safety section of
this manual, page 10.
GUN WILL FIRE WITH

MAGAZINE REMOVED OR
WITH EMPTY MAGAZINE
TO CLEAR A MALFUNCTION (JAM)

If a jam occurs, immediately put the safety selector switch in the SAFE
position and be certain the muzzle of the rifle is at all times pointing in
a safe direction.
Study the situation to determine the nature of the jam and how best to clear it.
If a cartridge or fired case is caught between the bolt and the barrel, or
against a cartridge that is in the chamber, remove the magazine and retract
the bolt fully. Now remove the jammed cartridge or case. If there is a
cartridge in the chamber, remove it.
When attempting to extract a cartridge that is stuck in the chamber, do
not use any type of tool that is likely to act as a firing pin and fire the
cartridge should the tool impact the primer.
After clearing a jam, inspect the guns mechanism to determine if dirt
might be the cause of the problem. Excess lubricant or grease can cause
cartridges to feed sluggishly or fail to extract. An accumulation of grease or
dirt on the face of the bolt, under the extractor, in the chamber, or in the
magazine can contribute to cartridge feeding problems. See section on
Care and Cleaning page 41.
After clearing a jam, inspect all cartridges that have been removed from the
gun. Safely dispose of any cartridges which are in any way damaged.
If it appears that the rifle is not at fault and that the jam was caused by the
type of cartridge being used, then try another type.
Examine your fired cartridge cases. If they have split, blown or bulged
heads, stop using that ammunition and promptly return the rifle to the
factory for examination.
21
If the above procedures do not result in a smooth and reliable feeding

firearm, do not use the rifle. The RUGER PRECISION RIFLE can
be returned directly to our Newport Customer Service Department for
inspection and repair, if required. See the Service and Parts Policy section
of the manual for packing and shipping information on page 46.
WARNING MALFUNCTIONS
If a cartridge hangs up, jams, or binds when
being chambered or when being fed from the
magazine into the chamber, do not attempt to
force it into the chamber by pushing or striking
the bolt handle.
Most failures of a cartridge to feed or to
chamber are caused by improper loading of the
magazine or ammunition that is incorrect or
defective.
Whatever the cause, the user must, above all,
recognize that jams can result in the
potentially very dangerous situation of a
cartridge firing before it is chambered. If this
occurs, the cartridge case will rupture and its
fragments will fly out of the gun with sufficient
force to cause injury. Always wear shooting
glasses and hearing protection!
STRIKING PRIMER CAN

BURST CARTRIDGE
TO MINIMIZE MALFUNCTIONS (JAMS)

Firearms of all makes and types are susceptible to occasional malfunctioning due to a
cartridge not feeding from the magazine to the chamber, or due to a cartridge or fired
case not being extracted and ejected.
To minimize the possibility of such occurrences the gun user should:
Use ammunition of the correct caliber and type which is loaded to U.S. Industry
Specifications. Do not use cartridges that are deformed or cartridges that have
been reloaded.
Clean and lubricate the gun in accordance with the instructions in this manual.
Learn to correctly operate the bolt and how to properly load and empty the
chamber and magazine.
If the mechanism shows signs of not functioning correctly, or if a part is damaged
or broken do not use the rifle. Have it inspected and repaired.
For most repairs, we recommend that Ruger guns be returned to the factory.
However, if a gun has a cartridge in it which cannot be removed, then it is a violation
of Federal Regulations to ship that loaded gun whether it be by U.S. Mail or by
common carrier. Contact our Newport Customer Service Department at (603) 8652442.
22
STOCK ADJUSTMENT
The RUGER PRECISION RIFLE has a folding butt stock that is
adjustable for length of pull and comb height.
WARNING FOLDING STOCK

The bolt on your Ruger
Precision Rifle should always
be in the forwardmost and
locked (handle down) position
when folding or opening the
stock. Failure to fully close the
bolt may result in damage to
the bolt shroud or bolt.
CLOSE BOLT
BEFORE FOLDING
OR OPENING STOCK
To Fold the Stock:
1. Keep the rifle pointed in a safe direction! Put the safety selector switch in the
SAFE position (see Figure 4, p. 11).
2. CHECK TO BE CERTAIN THAT THE CHAMBER AND MAGAZINE ARE
EMPTY. Remove the magazine.
3. Close the bolt.
4. Push the stock release button (see Figure 11) and fold the stock fully to the
left (see Figure 12).
Figure 11
Figure 12
23
Rotate the tab (opposite) end of the

stock release button clockwise turn
to lock the stock in the folded
position (see Figure 13).
Figure 13
To Unfold the Stock:

1. Keep the rifle pointed in a safe direction! Put the safety selector switch in the
SAFE position.
2. CHECK TO BE CERTAIN THAT THE CHAMBER AND MAGAZINE ARE EMPTY.
Remove the magazine.
3. Be certain the bolt is fully closed and locked.
4. Rotate the tab end of the stock release button counterclockwise turn to
unlock the stock. Unfold the stock until it snaps in place and locks.
To Adjust Length of Pull:
1. To adjust the length of pull, release the cam lever on the cheek piece and the
cam lever on the stock frame (see Figure 14). The entire butt pad assembly can
be moved in or out to lengthen or shorten the length of pull (see Figure 15).
Note that the butt pad and the cheek piece will move together when both cam
levers are released.
Figure 14
Figure 15
24
2. To lock the butt pad in place, both the cutout in the horizontal rod (see
Figure 16a) and the indexing lugs on the lower picatinny rail (see Figure 16b)
must be aligned with the rear of the butt stock frame (see Figure 16). Each
increment adjusts the length of pull by of an inch. The length of pull
should be set before adjusting the height of your cheek piece.
3. Lock down the two cam levers (see Figure 17).
Rear of butt stock frame.
16a
16b
Figure 16
Figure 17
Adjusting Cheek Piece:

1. Release the cheek piece cam
lever (see Figure 18).
Figure 18
25
2. Gently squeeze the cheek piece on the Ruger Eagle logo (see Figure 19).
3. Move the cheek piece up or down to the desired height. Each click is 1/16
of an inch (see Figure 19).
4. Lock the cam lever (see Figure 20).
5. The cheek piece cam lever can lock either upward or downward, and should
be locked in such a manner as to facilitate release at a later time.
Squeeze here from
both sides.
Move up
and down.
Figure 20
Figure 19
2
6. In order to move the cheek piece fore
and aft, you must first free the cheek
piece by releasing the cam lever and
rotating it 180. Now move the cheek
piece fore or aft to the desired
location. Finally, rotate the cam lever
back 180 and lock it down. (See
Figure 21.)
Figure 21
To Move Cheek Piece Toggle Lever to

Other Side of Stock:
1. The cheek piece cam lever can be
moved to the other side of the
stock. To switch the cheek piece
cam lever, release the cam lever,
and remove the nut, washer and
spring from the cheek piece.
(See Figure 22.)
Figure 22
26
2. Next, remove the cam lever, spring, and washer from the other side of the
cheek piece (see Figure 23).
Figure 23
3. Reassemble from the other side.

NOTE: Cam levers should be secure, but
they should not be overtightened. If the
cam levers are too tight, release the cam
lever, loosen the nut on the opposite side a
quarter turn, and lock the cam lever down
to check the tension. Repeat until the cam
lever tightens easily and keeps the butt
stock and cheek piece firmly in place.
B
A
4. The contact portion of the cheek piece

can be adjusted fore and aft by
removing the cheek piece, rotating it
180, and reinstalling it.
(See Figure 24.)
Figure 24
Cant Angle of the Butt Pad:
Figure 25
1. Make sure both cam levers are

locked (see Figure 20, p. 26).
2. Using a 9/64 Allen wrench, remove
the two screws on the back of the
butt pad and remove the butt pad.
(See Figure 25.)
27
3. Using a 5/32 Allen wrench on the middle screw of the butt pad frame and a
1/2 open end wrench on the front of the length of pull rod, loosen and
remove the center screw from the butt pad frame. (See Figure 26.)
4. Using a 5/32 Allen wrench, loosen the lower butt pad frame screw. (See
Figure 27.)
Figure 26
Figure 27
5. The cant of the butt pad can be adjusted either 9 degrees left or right by
changing the hole that the middle butt pad screw passes through. Select the
desired cant and insert the middle butt pad screw.
6. Re-install the lower butt pad frame screw using a 5/32 Allen wrench.
7. Tighten the middle butt pad frame screw with a 1/2 inch open end wrench
and a 5/32 Allen wrench.
8. Reinstall the recoil pad using a 9/64 Allen wrench.
TRIGGER PULL WEIGHT ADJUSTMENT

The trigger pull weight on the RUGER PRECISION RIFLE can be
adjusted from approximately 2 1/4 - 5 pounds.
To Adjust the Trigger:
cocked. Note that cocking the firing pin by lifting the bolt handle is required
to allow the rifle to enter the SAFE mode.
28
4. Raise the bolt handle and draw the bolt fully to the rear, extracting and
ejecting any cartridge in the chamber.
point no magazine should be in the rifle.
7. Rotate the rifle so that the magazine opening in the lower receiver is facing
upwards.
8. Locate the slot running through the magazine release lever. Using a 5/64
Allen wrench, insert the long end into that slot and down into the square
passageway in the lower receiver (see Figure 28). (Note: An Allen wrench for
this operation is supplied in the bolt shroud located on the back of the rifle
bolt.)
9. The adjusting screw is treated with a thread locking compound and may be
difficult to move. Threading the screw in (turning clockwise) will increase the
trigger pull weight, threading the screw out (turning counterclockwise) will
reduce the trigger pull weight. Approximately six full turns of the screw
represents the entire range of trigger pull weight adjustability. Turning the
screw beyond this amount will not further increase or decrease trigger pull
weight.
Slot in magazine
release lever.
Figure 28
10. We suggest turning the screw in no more than 1/2 revolution increments and
testing the pull weight before further adjustment is attempted. Repeat the
steps outlined above as required to reach desired pull weight.
We suggest you familiarize yourself with the triggers pull weight by dry firing
(ensure the magazine is removed, the chamber is empty, and the rifle remains
pointed in a safe direction) the rifle after a trigger pull weight adjustment,
before live ammunition is fired.
Always visually double check the chamber to be certain it is empty prior to dry
fire.
29
RUGER PRECISION RIFLE ACCESSORIES

Quick Detach Sling Mount Installation:
Your RUGER PRECISION RIFLE comes with several quick detatch
(QD) mounting locations. There is one on the left side of the adjustable stock
(see Figure 29), one on the back of the lower receiver when the stock is folded
(see Figure 30), and one on the recoil pad back plate (see Figure 31). A QD sling
mount (purchased separately) can be installed by pressing the center button on
the sling mount (see Figure 32), and inserting it in any of the QD mounting
locations on the rifle. (Operation of the sling mounts may vary, consult the
instructions with the sling mount for specific information.)
To remove the QD sling mount, simply press the center button and pull it out of
the stock. (See Figure 32.)
Figure 29
Figure 30
QD Mounting
Location
QD Mounting
Location
Figure 32
QD Mounting
Location
Figure 31
30
Reversing Side QD Attachment Point:

The QD attachment on the side of the adjustable stock can be relocated to the opposite
side to accommodate alternate sling locations. To relocate this QD mounting location:
1. Loosen and remove the QD swivel cup using a 12mm wrench (see Figure 33).
2. Using a 1/8 Allen wrench, remove the screw on the opposite side (see Figure 34).
3. Switch the screw to the reverse side and tighten using a 1/8 Allen wrench. NOTE:
The screw must be tightened to the center rod prior to installing the QD swivel cup.
4. Reinstall the QD swivel cup using a 12mm wrench.
Figure 33
Figure 34
QD Mount Attachment:
Your RUGER PRECISION RIFLE also comes with a QD mount that can
be installed on the handguard using the Key Mod mounting holes. (The mount is
located in the accessory pack included in your rifle box.) To attach the QD
mount, first loosen the screw with a 3/32 Allen wrench. Now slide the mount
into the Key Mod slot of your choice (see Figure 35). The screw on the QD
mount should be inserted first and nearest to the muzzle (with the mount
nearest the stock). Finally tighten the screw on the QD mount with the 3/32
Allen wrench (see Figure 36).
Figure 35
Figure 36
Muzzle end
of rifle.
Muzzle
end of
rifle.
31
Picatinny Rail Attachment:

Your RUGER PRECISION RIFLE also includes a section of Picatinny
Rail (Mil Spec 1913) that can be installed on the handguard using the Key Mod
system for mounting lights, lasers or other devices that utilize a Picatinny Rail
mount. The Picatinny Rail is located in the accessory pack included in your rifle
box. The accessory pack also includes a conventional sling stud that can be
installed on the Picatinny Rail and utilized as a mounting point for a bipod.
Figure 37
To install the sling stud on the

Picatinny Rail, first remove the center
screw using a 3/32 Allen wrench (see
Figure 37). Be careful to hold the nut in
place when removing the screw. (If you
drop the nut, you must take care to
reinstall it in the correct orientation
(see Figure 38). Carefully thread the
sling stud into the nut a few turns (see
Figure 39).
Figure 38
Figure 39
32
To mount the Picatinny Rail, loosen the screws using a 3/32 Allen wrench
(provided), and loosen the sling stud by hand (if installed). Next, slide the nut
(located on the back of the rail) into the Key Mod slots on the handguard (see
Figures 40A & 40B).
Figure 40A
Figure 40B
Muzzle
end of
rifle.
Nut
Tighten the screws using the 3/16 Allen wrench (see Figure 41). Tighten and
align the sling swivel so that it is perpendicular to the barrel (see Figure 42).
Figure 42
Figure 41
Align
Sling
Swivel
33
WARNING DISASSEMBLY
1
SAFETY IN
"SAFE" POSITION
Always unload a firearm

before cleaning, lubrication,
disassembly or assembly.
UNLOAD BEFORE
PERFORMING
MAINTENANCE
DISASSEMBLY
(Rifle Must Be Unloaded Prior to Disassembly)
This section will cover disassembly of the RUGER PRECISION RIFLE. It
will only be necessary to disassemble up to the step required for the particular area
you will be servicing. Disassembly beyond what is described in this section is not
recommended and may result in a non-functioning firearm.
An on-line video demonstrating the disassembly and reassembly of the RUGER
PRECISION RIFLE can be viewed by going to www.ruger.com/precisionrifle.
It is preferable to carry out these procedures on a workbench or table which has a
covered top. A piece of shallow nap rug or an old, coarse blanket is an ideal
covering. Such a covering not only reduces the chances of the rifle slipping and
being scratched, but also it serves to trap pins, plungers and springs that may
otherwise get lost. It is advisable to have a container such as a shoebox in
which each part can be placed as it is removed from the gun.
Before attempting to disassemble the rifle for the first time, study the parts
drawing and parts list to become familiar with the relative position, appearance and
name of each part. Carry out the disassembly slowly and carefully note the position
of the part in the gun before starting to remove it. If a part is under spring tension,
remove it cautiously and anticipate the direction the spring and plunger are most
likely to jump.
WARNING: If a spring or plunger becomes lost, do not use a substitute. Springs of
correct tension are vital to the safe and reliable performance of firearms. Before
starting disassembly, it is recommended to remove any unnecessary accessories
that may interfere with the handling of the firearm.
34
To Disassemble Your Ruger Precision Rifle:

cocked.
4. Raise the bolt handle and draw the bolt fully to the rear, extracting and
ejecting any cartridge in the chamber.
5. If the safety selector switch is in the FIRE position, move it to the SAFE
position (see Figure 4, p. 11).
point no magazine should be in the rifle.
7. To remove the bolt: Close the bolt and
push the folding stock release button
(see Figure 43).
Figure 43
Fold the stock to the left (see Figure 44). Rotate the tab end of the folding
stock button clockwise turn and lock the stock in the folded postion (see
Figure 13, p. 24). Remove the bolt by lifting the bolt handle and retracting
the bolt while at the same time pressing on the rear of the bolt stop located
on the left side of the receiver (see Figure 45). This is as far as you need to
dismantle the rifle for a routine cleaning.
Figure 45
B
Figure 44
35
Disassembly of Bolt for Cleaning:

If the rifle is used extensively, it may occasionally be desirable to lubricate the
cocking cams. Note that this is not something that should be necessary under
typical usage conditions.
To clean the bolt: NOTE: The cocking piece will only rotate fully if turned
clockwise, relative to the bolt body (when viewed from the rear of the bolt see
Figure 7, p. 13 for proper position). Do not rotate the cocking piece beyond the
positions shown in the instructions. If the cocking piece is turned too far, it will
fall down to the bottom of the cocking cams and will take significant effort, and
possibly the use of hand tools or a gripping aid, to return the cocking piece to
the correct cam notches. Because there are dual cocking cams, you may need to
rotate the cocking piece through both cams in order to return the cocking piece
to its proper position.
a. Start with the bolt in the position shown in Figure 46. You can see the
lobe on the cocking piece is at rest inside the notch on the cam.
Figure 46
Bolt Handle
Firing Pin
Back
Firing Pin
Lobe of Cocking
Piece at Rest in
Notch on Cam
Bolt Body
Bolt Shroud
b. Grasp the outside of the bolt shroud and cocking piece, and rotate
clockwise (when looking from the rear of the bolt) approximately 30 as
shown so the cocking piece lobe is aligned with the center of the bolt
handle base. (See Figure 47A & B.)
c. Pull the bolt shroud rearward and off. (See Figure 47C.) This is as far as
you need to dismantle the rifle to lubricate the cocking cams.
A Turn Bolt Shroud Clockwise
C Remove
Bolt Shroud
B
36
Center of Bolt
Handle Base
Figure 47
d. To lubricate cocking cams: A grease-type gun lubricant is recommended.

Grease cam surfaces and the firing pin shaft as shown in Figure 48. Note
further disassembly of the bolt is not required for lubrication. Some parts
are under spring tension and may dislodge abruptly if removal is
attempted. Grease may also be lightly applied to the lug surface of the
bolt as shown in Figure 49.
Lubricate Firing Pin Shaft
Lubricate
Cocking Cams
Figure 48
Lubricate Lug Surfaces
Figure 49
Lubricate Lug Surfaces
37
LOWER RECEIVER DISASSEMBLY

NOTE: The following steps should only be performed if inspection and or
cleaning of the lower receiver are required. It also will be necessary to perform
these steps to reverse the safety selector switch (see page 39). Otherwise, always
leave the lower receiver assembled.
1. CHECK TO BE CERTAIN THAT THE CHAMBER AND MAGAZINE ARE
EMPTY. Remove the magazine.
2. Using a 3/16 Allen wrench, remove the cap screw at the bottom of the upper
receiver. (See Figure 50.)
3. Unfold the stock, and using a 3/16 Allen wrench remove the cap screw at the
front of the lower receiver as shown in Figure 51. NOTE: Only remove the
cap screws as identified above; no other cap screws should be removed or
loosened.
Cap
Screw
Figure 51
Cap
Screw
Figure 50
4. Rotate the rifle so that the magazine well opening is facing upwards.
5. Verify that the safety selector switch in is in the SAFE position (see Figure 52)
and lift upwards on the lower receiver (see Figure 53). Note: If the safety selector
switch is not in the SAFE position, the lower receiver cannot be removed.
Figure 53
SAFETY ON
Figure 52
6. This is as far as you need to dismantle the rifle to clean the lower receiver and
inspect the internals.
38
REVERSING THE SAFETY SELECTOR SWITCH

Now that the lower receiver is separated from the rifle, you can remove and
reverse the safety selector switch, if desired. First, remove the safety selector
switch by pulling it out from the indicator side (see Figure 54). Next, insert the
safety selector switch into the other side of the lower receiver until it bridges
across both holes (see Figure 55).
NOTE: There are no detent pins or springs in the system; the fire control
housing retains the safety selector switch in the rifle. Take care to keep the safety
selector switch in place during reassembly.
Figure 54
Figure 55
TRIGGER GROUP
Over time and with extensive use, it will become necessary to remove and clean
the trigger group. It is recommended that you clean the trigger group
approximately every 1,000 rounds. An increase in trigger pull weight (without
adjustment) is an indicator that the trigger group may require cleaning.
The following steps should be performed if inspection and/or cleaning of the
trigger group is required. Otherwise always leave the trigger group assembled:
1. Using a 3/16 Allen wrench remove the bolt at the front of the trigger
assembly. (See Figure 56.)
2. Release the cocking guide spring by depressing the pin and allowing it to
move into the long portion of the J shaped slot. (See Figure 57.)
Figure 57
Figure 56
39
3. The cocking piece guide holds the trigger assembly forward and in place.
Using a non-marring tool, depress the cocking piece guide through the bolt
opening inside the receiver. (See Figure 58.) While holding the cocking piece
guide down, slide the trigger assembly rearward towards the butt stock and
out of the rifle (see Figure 58).
4. The trigger group should now be free from the receiver (see Figure 59). This
is as far as you need to dismantle the rifle to clean the trigger group and
inspect the internals. Note: Further disassembly of the trigger group is not
required for cleaning, some parts are under spring tension and may
dislodge abruptly if removal is attempted.
Cocking Piece Guide
Figure 58
HOW TO CLEAN THE TRIGGER GROUP

To clean your trigger group:
1. Materials recommended: non-chlorinated parts cleaner, cotton swab or other
soft pointed cleaning tool, an oil-type gun lubricant, and a synthetic greasetype lubricant such as Slip 2000 EWG or equivalent (see Figure 59A).
2. With the trigger group removed from the rifle, spray the inside of the trigger
group and surfaces as indicated in Figure 59.
3. Using a cotton swab, wipe down all visible surfaces as shown in Figure 59.
Wipe away any debris that can be seen in and around the housing.
Wipe Down
Surfaces
Spray inside of
trigger group
Figure 59A
Figure 59
40
4. Apply a drop of an oil-type gun

lubricant to the axle shafts of the
trigger group as shown in Figure
60. Allow the oil to run down the
shaft into the assembly.
Oil these
locations
5. Using the Slip 2000 EWG

syringe, apply grease to the
trigger and sear (see Figure 60A).
Insert grease where the sear
meets the top of the trigger (see
Oil these
Figure 60B), until a 1/8 bead
locations
Figure 60
forms between the parts. Note
the grease will spread along the
surfaces and be visible through the inspection ports as shown in Figure 60C.
6. Apply a small bead of grease to the opposite side of the sear as shown in
Figure 60D.
Figure 60B
Trigger
Apply
Grease
Sear
Figure 60C
Figure 60A
Grease seen through

inspection port.
Figure 60D
41
Apply Grease
CARE AND CLEANING

BEFORE CLEANING, BE CERTAIN THE RIFLE
AND ITS MAGAZINE CONTAIN NO CARTRIDGES.
An on-line video demonstrating the cleaning of the RUGER PRECISION
RIFLE can be viewed by going to www.ruger.com/precisionrifle.
A firearm must be free of rust, dirt, grease and firing residues to function safely and
reliably. Periodic maintenance, which includes inspection of components to determine
if they are in proper working order, is absolutely essential. Firing deposits particles of
bullet, lubricant and powder in the bore, chamber, bolt, receiver, magazine and other
parts of the rifle. There is no fixed rule as to how frequently the cleaning should be
carried out, but the alert gun owner soon learns that any firearm functions most
reliably and accurately when it is free of accumulations of grease and other firing
residues.
Basic cleaning equipment includes: A correct size cleaning rod equipped with bore
brushes (fiber and brass) and a tip in which a cloth patch can be inserted, patches,
powder solvent, lubricant, small lint-free cloths and a toothbrush. Use correct size
patches and brushes. Larger sizes will bind in the bore and can be very difficult to
remove! Insert rod from the chamber end of the barrel and push firmly so the patch or
brush emerges from the muzzle. Do not reverse the rod when a brush or patch is being
used before the brush or patch exits the muzzle it may bind. Do not use patches or
brushes dripping with solvent or oil. Use rod and brushes with care so as not to damage
the gun.
1. For routine cleaning it is necessary only to remove the bolt and magazine.
2. Push-pull a properly sized, solvent-wetted patch through the bore several times.
Next, using a solvent-wetted brush, run it the full length of the bore as many times
as is necessary to completely remove all foreign matter from the bore and chamber.
Dry the bore with clean patches and examine it. If the bore remains fouled, repeat
the brushing. Complete the cleaning by dry-patch wiping of bore and chamber.
3. Use a clean, solvent-wetted patch to remove firing residue and dirt from all
reachable surfaces inside the receiver. Use the solvent-wetted toothbrush to
dislodge caked dirt from all parts of the bolt assembly and from surfaces inside the
receiver that cannot be reached with a patch. Use cleaning patches or the cloth to
remove the solvent.
4. If lifting the bolt handle becomes difficult or requires more force than usual,
remove the end cap (see Disassembly of Bolt for Cleaning, p. 36 & 37) and clean
and lubricate the bolt cocking cam surfaces.
5. Wipe all surfaces internal and external with a very light coat of oil. Oil and
similar preparations collect dirt particles which can interfere with reliable
functioning of the rifle. Therefore, use these preparations very sparingly. A drop of
oil applied to the bolt assembly components, the pivot points of the trigger
mechanism, the safety, the bolt stop, and the magazine latch, will work into all the
parts that need lubrication.
6. Reassemble the rifle and carefully wipe off all excess solvent, lubricating and
preservative preparations from the rifle.
7. If the rifle is to be stored for an extended period, clean the rifle thoroughly.
Disassemble to the extent described elsewhere in this manual, taking care to put
pins and similar easily mislaid and rolling components in a tray. Rewipe all
surfaces with preservative oil. Reassemble and store properly.
42
WARNING LUBRICATION
IL
Firing a rifle with oil, grease, or any other material even

partially obstructing the bore may result in damage to the
rifle and serious injury to the shooter and those nearby.
Do not spray or apply lubricants directly on ammunition.
If the powder charge of a cartridge is affected by the
lubricant, it may not be ignited, but the energy from the
primer may be sufficient to push the bullet into the bore
where it may become lodged. Firing a subsequent bullet
onto the obstructed bore may damage the rifle and cause
serious injury or death to the shooter and those nearby.
Use lubricants properly. You are responsible for the proper
care and maintenance of your firearm.
IMPROPER LUBRICATION
DESTROYS GUNS
REASSEMBLY
1. Trigger Group: With the upper receiver standing upside down on a bench,
insert the trigger group into the receiver, and slide it away from the butt
stock. (See Figure 61.)
a. Grasp the cocking piece guide and maneuver it into the mating feature,
making sure that it seats out fully against the receiver (see Figure 62A).
b. Compress the cocking piece guide spring by moving the pin into the short
portion of the J shaped slot. (See Figure 62B.)
c. Using a 3/16 Allen wrench, tighten the front trigger assembly screw. (See
Figure 56, p. 39.)
Figure 61
Figure 62
A
Cocking piece guide
2. Lower Receiver: Insert the safety selector switch into the lower receiver, and
with the safety selector switch in the SAFE position, install the lower
receiver back onto the rifle. Fold the stock and install the cap screw. Then
unfold the stock and install the cap screw (sequence is important to properly
seat components). Follow Figures 50 through 53, p. 38, in reverse order.
3. Test the function of the safety.
43
4. Bolt Reassembly:
a. Install the bolt shroud by sliding it over the end of the firing pin. Rotate
the bolt shroud 30 degrees counterclockwise (see Figure 62) and the
firing pin back will lock into the bolt in the at rest position (see Figure
63).
b. Replace the bolt in the rifle and visually double check the chamber to be
certain it is empty. At this point no magazine should be in the rifle.
C Turn Bolt Shroud Counterclockwise
A Reinstall
Bolt Shroud
Center of Bolt
Handle Base
Figure 62
Lobe of Cocking
Piece at Rest in
Notch on Cam
Figure 63
While practicing safe firearm handling skills, test the movement and function of
the safety from the safe position to the fire position. By dry firing the rifle,
ensure that the safety is preventing the firing pin from advancing. If the above
procedures do not result in a safe operating firearm, do not use the gun. The rifle
can be returned directly to our Newport, New Hampshire Customer Service
Department for repair. See the Service and Parts Policy section, page 46, of
this manual for packing and shipping information.
44
STORAGE
GUNS SHOULD NOT BE STORED LOADED!
USE THE LOCKING DEVICE SUPPLIED WITH

THE RIFLE FOR STORAGE.
(See Page 7)
Do not store the rifle in a leather case or scabbard. Leather attracts moisture,
even though it may appear to be dry.
WARNING STORAGE
Never place or store any firearm in
such a manner that it may be
dislodged. Firearms should always be
stored securely and unloaded, away
from children and careless adults.
Use the locking device supplied with
the rifle for storage. The use of a
locking device or safety lock is only one
aspect of responsible firearms storage.
For increased safety, firearms should
be stored unloaded in a location that is
both separate from their ammunition
and inaccessible to children and any
other unauthorized person.
STORE SECURELY & UNLOADED
45
SERVICE AND PARTS POLICY

If you have any question with regard to the performance of your RUGER
PRECISION RIFLE please write or call (603-865-2442) our Customer
Service Department in Newport, New Hampshire 03773, fully describing all
circumstances and conditions involved. If you should return your rifle to the
factory for repair, or order parts for it, please comply with the following
suggestions for prompt service:
WARNING: BEFORE SHIPPING ANY FIREARM,

BE ABSOLUTELY CERTAIN THAT THE FIREARM AND ITS
MAGAZINE ARE UNLOADED. DO NOT SHIP CARTRIDGES
WITH A FIREARM.
SHIPPING FIREARMS FOR REPAIR

RUGER PRECISION RIFLES returned to the factory for repair should
be sent to: Sturm, Ruger & Company, Inc., Customer Service Department, 411
Sunapee St., Newport, New Hampshire 03773. The complete rifle should be
shipped. NOTE: You must obtain a Repair Authorization Number before
returning your firearm. An authorization number can be obtained by contacting
Customer Service online at www.ruger.com or calling the Customer Service
Dept. at 603-865-2442. Guns should be sent prepaid. We will not accept collect
shipments.
The Federal Gun Control Act, as well as the laws of most states and localities, do
not prohibit an individual (who is not otherwise barred from purchasing or
possessing a firearm) from shipping a firearm directly to the manufacturer for
repair. However, before you ship your rifle to us, be certain that your state or
locality does not have a law or regulation which will prohibit you from receiving
the rifle from us after it has been repaired. If such receiving is prohibited, then
please have a Federally Licensed Firearms Dealer ship the gun to us. If your rifle
is sent to us by a dealer, it will be returned to that dealer after being repaired.
DO NOT SEND GUN BOXES OR LITERATURE THAT YOU CONSIDER TO BE
COLLECTORS ITEMS THESE ARE INVARIABLY DAMAGED OR
DESTROYED IN SHIPMENT. Please do not include rifle case, sling, telescopic
sights or custom accessories with a firearm being shipped to the factory for
service. Rifles and shotguns may be shipped via U.S. Mail. Always insure your
shipment.
Enclose a letter which includes your name, address, telephone number, serial
number, model of the firearm, and your repair authorization number. Describe in
detail the trouble you have experienced with your firearm, or the work you wish
to have done. Merely stating that the firearm needs repair is inadequate
information.
All work performed is subject to a minimum labor charge and charges for
shipping and handling. Most models can be reblued, but custom gunsmithing
service or nonstandard alterations are NOT AVAILABLE from Ruger Customer
Service Departments. Please contact the Customer Service Department for
pricing information.
46
WARNING PARTS PURCHASERS

It is the purchasers responsibility to be
absolutely certain that any parts ordered from
the factory are correctly fitted and installed.
Firearms are complicated mechanisms and
IMPROPER FITTING OF PARTS MAY RESULT
IN A DANGEROUS MALFUNCTION, DAMAGE
TO THE FIREARM, AND SERIOUS INJURY TO
THE SHOOTER AND OTHER PERSONS.
The purchaser and installer of parts must
accept full responsibility for the correct
adjustment and functioning of the firearm
after such installation.
PARTS MUST FIT CORRECTLY
ORDERING PARTS
Please contact the New Hampshire Customer Service Department for parts
availability and current prices. All parts orders for the RUGER PRECISION
RIFLE should be sent to: Sturm, Ruger & Co., Inc., Customer Service
Department, 411 Sunapee Street, Newport, New Hampshire 03773, 603-865-2442.
We cannot comply with open account or C.O.D. requests. Payment in full via
credit card (Visa or MasterCard only), money order or certified bank check (no
personal checks or cash, please) is required before any service will be performed.
Please provide your credit card number, your name as it appears on the credit
card, the expiration date, and the 3-digit security code. All parts orders are subject
to a minimum charge and charges for shipping and handling. Order parts by Part
Name and Part Number and include the entire serial number of the firearm for
which the parts are being ordered. There is a minimum labor charge plus a
shipping and handling charge if the parts are factory fitted. All factory fitted parts
are fit on an exchange basis only. We will not return the replaced parts. Please
contact the Customer Service Department for pricing information.
Barrels, and a number of other component parts must be fitted at the factory.
Company policy is to proof-test and/or function fire all barrels after fitting to the
receivers in which they are to be used. This procedure ensures maximum
protection to our customers. The special proof-test ammunition used in this
testing is sold only to bonafide firearms manufacturers and is not available to gun
shops, gunsmiths or individuals.
Because the receiver of the RUGER PRECISION RIFLE is a serial
numbered component, it is defined as a firearm by Federal law and is not sold as
a separate component.
*Parts designated by an asterisk must be factory fitted. These parts are fitted on an
exchange basis only. We will not return the replaced parts. We will not return any
part that is broken, malfunctioning, badly worn or has been modified. See
Warning Parts Purchasers, above.
WARNING: A gun containing broken, malfunctioning or badly

worn parts should not be fired.
47

PARTS LIST
Design, prices and specifications subject to change without notice.
(See Exploded Views on Pages 51 -54)
Key
*
1
2
*
*
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
* 19
*
*
*
*
*
*
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Part Name
Part No.
Model
Bolt / Firing Pin Assembly Complete

All Models
Includes Key Nos. 2 - 18 (See Exploded View p. 51)
Bolt Shroud Assembly, Short
DBA21702
All Models
w/Cap & 5/64 Hex Wrench
Firing Pin Back
DBA01802
All Models
Firing Pin Spring Stop
DBA03501
All Models
Firing Pin, Short Action
DBA01102
All Models
Firing Pin Spring
DBA01201
All Models
Bolt Knob
DBA00088
All Models
Ejector/Firing Pin Back Pin
DBA01900
All Models
Ejector Spring
DBA00901
All Models
Ejector Plunger
DBA00802
All Models
Extractor
DBA01401
All Models
Extractor Ball
DBA08601
All Models
Extractor Spring
DBA08701
All Models
Bolt Body, Short Action
DBA01008
All Models
Bolt Handle
DBA01603
All Models
Receiver
TAC00100
All Models
Barrel Nut
DBA00303
All Models
Barrel
0TAC8001
18001
Barrel
0TAC8002
18005
Barrel
0TAC8003
18010
Trigger Assembly Complete
All Models
Safety Connector
DBA03704
All Models
Cocking Piece Guide Spring
DBA02415
All Models
Cocking Piece Guide
DBA01320
All Models
Sear Spring
DBA02402
All Models
Sear
DBA02301
All Models
Safety Link
DBA03703
All Models
Sear Stop Pin
DBA05601
All Models
Trigger block Pin
DBA04502-135
All Models
Trigger-Sear Pin, 3 Reqd
DBA02101
All Models
Safety Shaft
DBA03603
All Models
Safety Spring
DBA05402
All Models
Trigger Housing
DBA01302
All Models
Trigger-Sear Pin E-Clip, 3 Reqd
DBA04201
All Models
Trigger Block Pin E-Clip
DBA04601
All Models
Safety Shaft E-Clip
DBA05501
All Models
* Parts so marked must be factory fitted.

The receiver is a serial-numbered part and is not offered for sale.
48
Key
*
35
36
* 37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
Part Name
Part No.
Model
Trigger Release
DBA05701
All Models
Trigger Release Spring
DBA04901
All Models
Trigger
DBA02002
All Models
Trigger Release Pin
DBA05901
All Models
Trigger Pull Adjustment Spring
DBA02503
All Models
Trigger Adjustment Screw
DBA08103
All Models
Stock Assembly Complete
Rail Cover
DBA13512
All Models
Butt Pad Screw, 2 Reqd
DBA08300
All Models
Recoil Pad
D06319
All Models
Recoil Pad Base Plate Screw, 2 Reqd DBA00092
All Models
Recoil Pad Base Plate
DBA06301
All Models
Lower Picatinny Rail
DBA13506
All Models
Adjustment Rod
DBA13505
All Models
Rear Stock Frame
DBA15302
All Models
Cheek Rest
DBA15304
All Models
Stock Cam Spring, 3 Reqd
DBA13511
All Models
Stock Detent Washer, 4 Reqd
DBA00039
All Models
QD Swivel Cup
DBA00083
All Models
Cam Nut, 2 Reqd
DBA00079
All Models
Buffer Tube
NS00400
All Models
Stock Front Clamp
DBA15301
All Models
Stock Connector Rod
DBA15303
All Models
Acorn Nut
DBA00089
All Models
Castle Nut
NS00088
All Models
End Plate
NS00087
All Models
Stock Front Clamp Bottom
DBA15305
All Models
Stock Clamp Screw, 2 Reqd
DBA00084
All Models
Cheek Clamp, 2 Reqd
DBA13510
All Models
Stock Length Lock
DBA13507
All Models
Cam Lever, 2 Reqd
DBA13508
All Models
Cam Cross Pin, 2 Reqd
KDBA13509
All Models
Cam Rod Short
DBA00077
All Models
Cam Rod Long
DBA00078
All Models
Stock Mount Back
DBA13700
All Models
Stock Pivot Latch
DBA00034
All Models
Stock Pivot Latch Pin
KDBA01901
All Models
Latch Spring
KDBA14401
All Models
Stock Mount Bottom
DBA13701
All Models
Stock Hinge Pin washer, 2 Reqd
DBA05603
All Models
Stock Hinge Pin
DBA05600
All Models
Stock Mount Top
DBA13702
All Models
Scope Mount Screw, 4 Reqd
DBA06103
All Models
Stock Latch detent Washer
DBA00038
All Models
* Parts so marked must be factory fitted.
49
Key
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
Part Name
Part No.
Model
Stock Pivot Lock Button

Bolt Stop Spring
Bolt Stop
Bolt Stop Pin
Scope Base
Hinge Mounting Screw, 2 Reqd
Mounting Screw, 2 Reqd
Barrel Nut Lock
Handguard Nut Ring
Handguard Nut
12 1/4 Handguard
w/ (2) Thermal Bushings
15 Handguard
w/ (2) Thermal Bushings
Muzzle Cap
Short Lower, Right
Short Lower, Left
Safety Selector
Mounting Screw, 3 Reqd
Lower Lever Pin
Side Catch Spring
Magazine Side Latch Pin
Magazine Latch Lever Spring
Magazine Latch Lever
Magazine Latch Side Catch
Lower Front Mount
Grip Screw
Grip Washer
Pistol Grip
Magazine
DBA00038
DBA05303
DBA05304
DBA05302
DBA08810
DBA04804
DBA00081
DBA01790
DBA00310
DBA00302
DBA16600
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
DBA16601
All Models
DBA01345
DBA13100
DBA13101
NS13800
DBA04801
KDBA03104
DBA03106
DBA05604
KDBA03202
DBA03102
DBA03103
DBA00670
NS00069
MA13500
ND00075
NS12711
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
All Models
50

BOLT / FIRING PIN ASSEMBLY
51

TRIGGER ASSEMBLY
52

STOCK ASSEMBLY
53

EXPLODED VIEW
54
THE BASIC RULES OF SAFE FIREARMS HANDLING

We believe that Americans have a right to purchase and use firearms for lawful
purposes. The private ownership of firearms in America is traditional, but that
ownership imposes the responsibility on the gun owner to use his firearms in a
way which will ensure his own safety and that of others. When firearms are used in
a safe and responsible manner, they are a great source of pleasure and satisfaction,
and represent a fundamental part of our personal liberty.
Firearms do not cause accidents! Firearms accidents are almost always found to
have been the result of carelessness or ignorance on the part of the shooter of the
basic rules of safe gun handling.
The following rules must be observed by gun users at all times. Safe gun handling
is not just desirable, it is absolutely essential to your safety, the safety of others, and
the continuation of gun ownership and sport shooting as we know it today.
1. LEARN THE MECHANICAL AND HANDLING

CHARACTERISTICS OF THE FIREARM YOU ARE USING.
Not all firearms are the same. The method of carrying and handling firearms
varies in accordance with the
mechanical provisions for avoiding
accidental discharge and the various
proper procedures for loading and
unloading. No person should handle
any firearm without first having
thoroughly familiarized himself with
the particular type of firearm he is
using, and with safe gun handling in
general.
2. ALWAYS KEEP THE

MUZZLE POINTED IN A
SAFE DIRECTION.
Be sure of the bullet stop behind
your target, even when dry-firing.
Never let the muzzle of a firearm
point at any part of your body or at
another person. This is particularly
important when loading or
unloading a firearm. In the event of
an accidental discharge, no injury
can occur as long as the muzzle is
pointing in a safe direction. A safe
direction means a direction that will
not permit a discharged bullet to
strike a person, or to strike an object
from which the bullet may ricochet.
55
A safe direction must take into account the fact that a bullet may
penetrate a wall, ceiling, floor, window, etc., and strike a person or
damage property. Make it a habit to know exactly where the muzzle of
your gun is pointing whenever you handle it, and be sure that you are
always in control of the direction in which the muzzle is pointing, even
if you fall or stumble. Keep your finger off the trigger until you are ready
to shoot.
3. FIREARMS SHOULD BE UNLOADED WHEN NOT IN

USE.
Firearms should be loaded only
when you are in the field or on the
1
target range or shooting area,
SAFETY IN
"SAFE" POSITION
ready to shoot. Firearms and
ammunition should be securely
3
4
locked in safes, racks or cabinets,
or by using the locking device
supplied with the firearm, when
not in use. Ammunition should
2
safely be stored separate from
firearms. Store your firearms out
of sight of visitors and children. It
is the gun owners responsibility to
be certain that children and
persons unfamiliar with firearms cannot gain access to firearms,
ammunition, or components.
4. BE SURE THE BARREL IS CLEAR OF OBSTRUCTIONS

BEFORE SHOOTING.
Even a bit of mud, snow or excess
lubricating oil or grease in the
bore may cause the barrel to
bulge, or even burst on firing, and
can cause serious injury to the
shooter and bystanders. Be sure
that you are using ammunition of
the proper caliber and loading for
the gun you are using. If the
report or recoil on firing seems
weak, or doesnt seem quite right,
CEASE FIRING IMMEDIATELY,
unload your firearm, and check to
be sure that no obstruction has
become lodged in the barrel. Never
try to shoot out an obstruction!
56
5. BE SURE OF YOUR
TARGET BEFORE YOU
SHOOT.
Dont shoot unless you know
exactly where your bullet is going
to strike. Be sure of the bullet
stop behind your target, even
when dry-firing with an unloaded
gun. If you are in the field
hunting, do not fire at a
movement or noise. Take the time
to be absolutely certain of your
target before you pull the trigger.
6. WEAR SHOOTING
GLASSES AND HEARING
PROTECTION WHEN
YOU SHOOT.
All shooters should wear
protective shooting glasses and
adequate hearing protection
when shooting. Exposure to
shooting noise can damage
hearing, and wearing adequate
eye protection when shooting is
essential.
7. NEVER CLIMB A TREE

OR FENCE WITH A
LOADED FIREARM.
Put the firearm down carefully
before climbing a fence, and
unload it before climbing or
descending a tree or jumping over
a ditch or other obstruction. Never
pull or push a loaded firearm
toward yourself or another person.
When in doubt, or whenever you
are about to do anything awkward,
unload your gun!
57
8. DONT SHOOT AT A
HARD SURFACE OR AT
WATER.
Bullets can glance off many
surfaces like rocks or the surface
of water and travel in
unpredictable directions with
considerable velocity.
9. NEVER TRANSPORT A
LOADED FIREARM.
Firearms should always be
unloaded before being placed in a
vehicle. A suitable carrying case
or scabbard should be used to
carry an unloaded firearm to and
from the shooting area.
10. AVOID ALCOHOLIC

BEVERAGES WHEN
SHOOTING.
Dont drink until the days
shooting is over. Handling
firearms while under the
influence of alcohol in any form,
or medications that could affect
your judgement or coordination,
constitutes a criminal disregard
for the safety of others.
58
A BRIEF ACCOUNT OF AN EXTRAORDINARY

ACHIEVEMENT: RUGER FIREARMS
Sturm, Ruger & Company, Inc., had its beginning in a small machine
shop occupying a rented frame building in Southport, Connecticut. In
January, 1949, with an initial investment of only $50,000 and an idea,
William B. Ruger and Alexander M. Sturm started production of a .22
caliber autoloading pistola design which was so successful that it
became the cornerstone upon which one of the most comprehensive
lines of sporting firearms ever made in America was established. After
Alex Sturms death in 1951, William B. Ruger continued to direct the
Company until his death in 2002. William B. Ruger, Jr. continued to
provide guidance, which helped make this Company a sound and
successful enterprise, until his retirement in 2006. The Company has
continued to prosper, under new management and guidance from our
Board, with new products and fresh perspectives.
Ruger, in this relatively short time, has established itself as a leading
small arms design organization, developing a unique and broad line of
fine quality sporting, military and police firearms to become one of the
worlds most famous producers of revolvers, pistols, rifles and shotguns.
Since 1949, Ruger craftsmen have built many millions of firearms.
During its five decades of growth and progress under the leadership of
William B. Ruger, the Company developed a business philosophy and
implemented policies which represent a constructive influence in the life
of modern America. From the beginning, Ruger played a positive role in
conservation efforts and has supported the interests of shooters through
such groups as the National Rifle Association, National Shooting Sports
Foundation, and many regional sportsmens organizations.
The Company has always endeavored to market its firearms for
constructive and recreational purposes, to emphasize the traditional and
responsible aspects of shooting, to render meaningful public services,
and to encourage shooters in constructive, responsible, and safe
participation in the shooting sports. Its motto, Arms Makers For
Responsible Citizens, exemplifies this Company philosophy.
Today, Ruger is particularly mindful of those elements which have
contributed to the creation of its success, and extends heartfelt thanks to
its many loyal employees and customers.
The firearms catalog, and instruction manuals for all Ruger firearms,
can be downloaded from our website at:
www.ruger.com
59
WHY NO WARRANTY CARD HAS BEEN

PACKED WITH THIS NEW RUGER FIREARM
The Magnuson-Moss Act (Public Law 93-637) does not require any
seller or manufacturer of a consumer product to give a written
warranty. It does provide that if a written warranty is given, it must be
designated as limited or as full and sets minimum standards for a
full warranty. Sturm, Ruger & Company, Inc. has elected not to
provide any written warranty, either limited or full, rather than to
attempt to comply with the provisions of the Magnuson-Moss Act and
the regulations issued thereunder. There are certain implied warranties
under state law with respect to sales of consumer goods. As the extent
and interpretation of these implied warranties varies from state to
state, you should refer to your state statutes. Sturm, Ruger &
Company wishes to assure its customers of its continued interest in
providing service to owners of Ruger firearms.
STURM, RUGER & COMPANY, INC.

411 Sunapee Street
Newport, New Hampshire 03773 U.S.A.
www.ruger.com
Arms Makers For Responsible Citizens
A COPY OF THE INSTRUCTION MANUAL FOR ANY RUGER
FIREARM IS AVAILABLE FROM THE FACTORY FREE ON REQUEST, OR IT MAY BE
DOWNLOADED FROM OUR WEBSITE AT WWW.RUGER.COM.
THESE INSTRUCTION MANUALS CONTAIN IMPORTANT
WARNINGS WHICH MUST BE UNDERSTOOD
BEFORE USING THESE FIREARMS.
The Following are Sturm, Ruger & Co., Inc. Trademarks: BX-Trigger, Bisley, Eagle SR, Elite 452, Gold
Label, Its Mine and Its American, LC6, LCR-357, LCRx, Mark II, Mark III, Match Champion,
Model 96, P345D, P345PR, P85, P90, P91, P93, P94, P95, P97, Ruger Marksman
Adjustable, Ruger 77/50, Ruger 10/17, 77/357, Single-Seven, SR45, SR-556C, SR-556VT, SR762, 10/22-FS, 22 Charger, 22/45, and 22/45 RP.
The Following are Registered U.S. Trademarks Belonging to Sturm, Ruger & Co., Inc.: RUGER,
Sturm,Ruger Logo, AC-556, AR-556, Arms Makers For Responsible Citizens, All-Weather, Bearcat,
Blackhawk, BX-15, BX-25, Eagle R, GP100, Hard R Logo, Hawkeye, LC380, LC9, LC9s,
LCP, LCR, M77, Mini Thirty, Mini-14, 9E, Old Army, Power Bedding, P345, Redhawk,
Ruger American Rifle, Ruger American Rimfire, Ruger Hunting, Ruger Hunting Logo, Ruger Inside &
Out phrase & logo design, Ruger 77/17, Ruger 77/22, Ruger 77/44, Ruger SP101, Ruger 10/22
Takedown phrase & logo design, Ruger Titanium, Ruger 22/45 Lite, Ruger Vaquero, Rugged, Reliable
Firearms, Security-Six, Service-Six, Single-Nine, Single-Six, Single-Ten, Speed-Six, the SR
Design, SR9, SR9c, SR40, SR40c, SR-22, SR22, SR-556, SR-556E, SR1911, Super Redhawk
Alaskan, Target Grey, 10/22, and 10/22 Takedown.

RugerPrecisionRifle Bp2dZ95h4Rs7

Uploaded by

Copyright:

Available Formats

RugerPrecisionRifle Bp2dZ95h4Rs7

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RugerPrecisionRifle Bp2dZ95h4Rs7

Uploaded by

Copyright:

Available Formats

S

Rugged, Reliable Firearms

For Service on This Model Please Call:

Certain states require by law that their own specified warning

Children are attracted to and

UNLAWFUL STORAGE OF A LOADED FIREARM MAY

IT IS UNLAWFUL, AND PUNISHABLE BY

ENDANGERING THE WELFARE OF A CHILD IS A

WARNING: Children can operate firearms which may cause

WARNING FROM THE MASSACHUSETTS ATTORNEY

IT IS A CRIMINAL OFFENSE TO LEAVE A LOADED

New York City:

THE USE OF A LOCKING DEVICE OR SAFETY LOCK IS

IT IS UNLAWFUL TO STORE OR LEAVE A FIREARM

IT IS UNLAWFUL TO STORE, TRANSPORT, OR

IF YOU LEAVE A LOADED FIREARM WITHIN THE

FIREARMS SAFETY IS YOUR RESPONSIBILITY

RUGER is a registered U.S. trademark.

WARNINGS OF GREAT IMPORTANCE ARE

OTHER CAUTIONS AND WARNINGS APPEAR

Always verify that your firearm is completely unloaded

Do not install locking devices in the trigger guard;

Store firearms, ammunition and keys separately and

Do not store keys

While locking devices are an important aid to security

LOCKING DEVICES MUST BE USED

Correct Installation of Cable Lock

FIREARMS ARE DANGEROUS WEAPONS

DO NOT ALTER ANY GUN

WARNING: When manipulating the safety selector switch, KEEP YOUR

WARNING MANUAL SAFETY

Keep the safety selector switch in the SAFE

KNOW HOW TO USE THE SAFETY

UNBOXING YOUR RIFLE

1. Keep the muzzle pointed in a safe direction and

6. Remove the rifle bolt from

WARNING FOLDING STOCK

USE ONLY FACTORY AMMUNITION LOADED

AMMUNITION (CARTRIDGES) NOTICE

WARNING LEAD EXPOSURE

SHOOTING OR CLEANING GUNS

Magpul PMAG 10 LR/SR GEN M3

DAMAGED, NON-STANDARD OR IMPROPERLY ASSEMBLED

INSERTING THE MAGAZINE

REMOVING THE MAGAZINE

LOADING THE MAGAZINE

CARE AND CLEANING OF MAGAZINE

TO LOAD AND FIRE (WITH MAGAZINE)

TO LOAD AND FIRE (WITHOUT MAGAZINE)

BE SURE WHAT YOU LOAD

WARNING: DO NOT TOUCH THE TRIGGER

ANY GUN MAY FIRE IF

CORRECT UNLOADING SEQUENCE

GUN WILL FIRE WITH

TO CLEAR A MALFUNCTION (JAM)

If the above procedures do not result in a smooth and reliable feeding

STRIKING PRIMER CAN

TO MINIMIZE MALFUNCTIONS (JAMS)

WARNING FOLDING STOCK