Tds - Penguard Classic ZP - English (Uk) - Issued.19
Tds - Penguard Classic ZP - English (Uk) - Issued.19
Tds - Penguard Classic ZP - English (Uk) - Issued.19
PENGUARD CLASSIC ZP
Product description
Penguard Classic ZP is a high build, two-pack zinc phosphate pigmented epoxy coating based on
epoxy resin with high molecular weight. Two hardeners (Comp. B) are available for varying substrate
temperatures, Standard (Std) and Cold Climate (CC).
Recommended use
As an anti-corrosive primer and/or intermediate coating for protection of steel and other substrates.
Can be used alone or in various systems of primers and topcoats.
Minimum
100
160
6,2
Maximum
150
240
4,1
Typical
100
160
6,2
Physical properties
Colour
Solids (vol %)*
Grey, Red
62 2
Flash point
25C 2 (Setaflash)
Gloss
Flat
Water resistance
Very good
Abrasion resistance
Very good
Solvent resistance
Excellent
Chemical resistance
Excellent
Flexibility
Good
*Measured according to ISO 3233:1998 (E)
Surface preparation
All surfaces should be clean, dry and free from contamination. The surface should be assessed and
treated in accordance with ISO 8504.
Bare steel
Cleanliness: Blast cleaning to Sa 2 (ISO 8501-1:1988). Roughness: using abrasives suitable to
achieve grade Fine to Medium G (30-85 m, Ry5) (ISO 8503-2)
Shopprimed steel
Clean, dry and undamaged approved shopprimer.
Coated surfaces
Clean, dry and undamaged compatible primer. Please contact your local Jotun office for more
information.
PENGUARD CLASSIC ZP
Page 1 of 4
Other surfaces
For aluminium and galvanised surface; degreasing, light abrading or sweep blasting. For stainless
steel; light abrading or sweep blasting using chloride free, non-metallic abrasive.
The coating may be used on other substrates. Please contact your local Jotun office for more
information.
Application methods
Spray
Brush
Application data
Mixing ratio (volume)
Mixing
Pot life (23C)
Thinner/Cleaner
Guiding data airless spray
Pressure at nozzle
Nozzle tip
Spray angle
Filter
Drying time
Drying times are generally related to air circulation, temperature, film thickness and number of coats,
and will be affected correspondingly. The figures given in the table are typical with:
* Good ventilation (Outdoor exposure or free circulation of air)
* Typical film thickness
* One coat on top of inert substrate
PENGUARD CLASSIC ZP
Page 2 of 4
Std Comp. B
Substrate temperature
Surface dry
Through dry
Cured
Dry to recoat, minimum
Dry to recoat, maximum
CC Comp. B
Substrate temperature
Surface dry
Through dry
Cured
Dry to recoat, minimum
Dry to recoat, maximum
1
10C
4h
16 h
14 d
16 h
23C
2h
8h
7d
8h
40C
1h
3h
3d
3h
5C
6h
20 h
16 d
20 h
10C
3h
10 h
8d
10 h
23C
2h
5h
4d
5h
0C
12 h
30 h
30 h
1
Provided the surface is free from chalking and other contamination prior to application, there is
normally no overcoating time limit. Best intercoat adhesion occurs, however, when the
subsequent coat is applied before preceding coat has cured. If the coating has been exposed to
direct sunlight for some time, special attention must be paid to surface cleaning and
mattening/removal of the surface layer in order to obtain good adhesion.
The given data must be considered as guidelines only. The actual drying time/times before recoating
may be shorter or longer, depending on film thickness, ventilation, humidity, underlying paint system,
requirement for early handling and mechanical strength etc. A complete system can be described on
a system sheet, where all parameters and special conditions could be included.
1 x 100 microns
1 x 100 microns
1 x 50 microns
Storage
The product must be stored in accordance with national regulations. Storage conditions are to keep
the containers in a dry, cool, well ventilated space and away from source of heat and ignition.
Containers must be kept tightly closed.
Handling
Handle with care. Stir well before use.
Packing size
16 litres Comp. A (base) in a 20 litre container and 4 litres Comp. B (curing agent) in a 5 litre
container
4 litres Comp. A (base) in a 5 litre container and 1 litre Comp. B (curing agent) in a 1 litre container
Packing may vary from country to country according to local requirements.
PENGUARD CLASSIC ZP
Page 3 of 4
Europe
Middle East
South East A s i a
Jotun A /S
P .O . Box 2021
N-3248 Sandefjord
Road
Norway
8RR
Jurong
P hone +47 33 45 70 00
Fax
+47 33 46 46 13
U nited Kingdom
P .O Box 3671
Dubai U .A .E
P hone
Fax
+971 4 3 39 50 00
+971 4 3 38 06 66
Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your
nearest local Jotun address please contact the nearest regional office or visit our website at www.jotun.com
PENGUARD CLASSIC ZP
Page 4 of 4