Manual Eng - Dixon
Manual Eng - Dixon
Manual Eng - Dixon
DESCRIPTION
PART No.
QTY.
FRONT TRIANGLE
8714-0300
SEAT STAYS
8812-9900
CHAIN STAYS
8714-9800
RIGHT LINKAGE
MFL14008
LEFT LINKAGE
MFL14009
M FV00073
M FV00120
MFP11022
MFP12020-XX
10
MFP12021-XX
11
ADJUSTER SHAFT
M FP12022
12
ADJUSTER SPACER
M FP12023
13
MFP11031
14
MFP11032
15
M FP11035
16
PIVOT NUT
MFP11011-XX
17
5
16
17
13
12
14
16
9
8
NO LOCTITE ON
THIS PART,
GREASE ONLY
2
12
11
BL PIVOT
8
8
8
DO PIVOT
4
8
10
CL PIVOT
WARNING:
MAKE SURE TO
CAREFULLY READ THE
ASSEMBLY
INSTRUCTIONS AND
CLEANING
INSTRUCTIONS NOTES
ON NEXT PAGE.
10
8
15
BL PIVOT
WL PIVOT
25 - 30 lb.in
2.8 - 3.4 N.m
55 - 65 lb.in
6.2 - 7.3 N.m
CL PIVOT
2
7
45 - 55 lb.in
5.1 - 6.2 N.m
55 - 65 lb.in
6.2 - 7.3 N.m
WL PIVOT
REAR AXLE
(160 - 180 lb.in)
(18 - 20.3 N.m)
DO PIVOT
ASSEMBLY INSTRUCTIONS:
1- THOROUGHLY CLEAN THE INTERIOR OF EACH BEARING HOUSING TO REMOVE ANY DIRT OR OLD GREASE;
2- APPLY HIGH QUALITY WATERPROOF GREASE ON THE INSIDE FACE AND INSIDE DIAMETER OF ALL BEARING HOUSINGS
BEFORE PRESS-FIT;
3- APPLY HIGH QUALITY WATERPROOF GREASE TO ALL PIVOT PARTS THAT CONTACT WITH THE INNER DIAMETER OF THE
BEARINGS (EX.: MFP12021);
4- APPLY HIGH QUALITY WATERPROOF GREASE TO ALL NON-THREADED METAL-TO-METAL INTERFACES (EX.: PLANAR FACE
OF THE PIVOT SPACER No1 (MFP11035) THAT CONTACTS THE LATERAL FACES OF THE FRONT TRIANGLE WL PIVOT). THESE
INSTRUCTIONS ALSO APPLY TO THE SHOCK ASSEMBLY;
5- UNLESS OTHERWISE SPECIFIED, APPLY BLUE LOCTITE 242 ON ALL THREADS BEFORE ASSEMBLY TO THE SPECIFIED
TORQUE VALUE;
6- HUB OPTIONS: YOU CAN SWITCH FROM A 142mm TO A 135mm HUB SIMPLY BY REPLACING THE PARTS MFP11031 AND
MFP11032 BY THE PARTS MFP11061 AND MFP11062;
7- TO PREVENT DAMAGE TO THE FRAME, THE SEATPOST MUST HAVE A MINIMUM INSERTION IN THE SEAT TUBE.
CARBON FRAME:
SMALL / MEDIUM - 70mm INSERTION
LARGE / X-LARGE - 100mm INSERTION
ALUMINIUM FRAME:
SMALL / MEDIUM / LARGE / X-LARGE - 100mm INSERTION
8- FRG ADJUSTABLE: THIS DESIGN ALLOWS RIDERS TO CHOOSE BETWEEN A LOW OR HIGH POSITION. WITH FRG
ADJUSTABLE TECHNOLOGY, YOU CAN FINE-TUNE YOUR RIDE TO PERSONAL TASTES OR SPECIFIC TRAIL TYPES USING A
FLIP-FLOP PIVOT MECHANISM THAT SLIGHTLY CHANGES THE BIKE'S GEOMETRY. FOR THE DIXON, THIS ADJUSTMENT IS
PROVIDED BY THE BL PIVOT ADJUSTER SHAFTS AND SPACERS (MFP12022 AND MFP12023), AS SHOWN BELOW.
LOW POSITION
HIGH POSITION
CLEANING INSTRUCTIONS:
IT IS A WELL KNOWN FACT THAT A CLEAN BIKE PERFOMS BETTER. DEVINCI RECOMMENDS WASHING
YOUR BIKE REGULARLY USING A BRUSH AND SOAPY WATER. HOWEVER, DEVINCI DO NOT
RECOMMEND THE USE OF A PRESSURE WASHER, SINCE THIS MAY SIGNIFICANTLY REDUCE THE
SERVICE LIFE OF BALL BEARINGS. EVEN THOUGH OUR BALL BEARINGS ARE EQUIPPED WITH HIGH
QUALITY DOUBLE-LIP SEALS, HIGH PRESSURE WATER CAN STILL PASS THESE SEALS AND REMOVE
THE GREASE INSIDE THE BEARING. THIS MAY CAUSE PREMATURE CORROSION AND WEAR OF THE
BALL BEARINGS.
DRIVETRAIN ASSEMBLY
1
CHAINRING BOLTS
DUE TO THE CONSTANT TENSION AND FORCES TO WHICH CHAINRINGS ARE EXPOSED, THEY REQUIRE REGULAR TORQUE INSPECTIONS TO
ENSURE THEY DO NOT TURN FREELY. PLEASE REFER TO THE CRANKS OWNER MANUAL FOR PROPER SPECIFICATIONS AND TIGHTENING
ORDER.
BOTTOM BRACKET
LOOSE BOTTOM BRACKET CUPS CAN ALTER THE FRAME BB THREADS AND CREATE LOUD CREAKING NOISES IF NOT DIAGNOSED/FIXED
QUICKLY. THEY CAN BE HARD TO DIAGNOSE AND ISOLATE DEPENDING ON A LOT OF DIFFERENT FACTORS. TAKING YOUR BICYCLE TO YOUR
DEVINCI AUTHORIZED DEALER IS ALWAYS PREFERED TO TRYING TO OVERHAUL THE WHOLE UNIT BY YOURSELF AS SPECIAL TOOLS/PROCEDURES ARE NEEDED. REMEMBER THAT IF YOU DECIDE TO PERFORM THESE CORRECTIONS BY YOURSELF, PLEASE ALWAYS REFER TO THE
RESPECTIVE PART OWNERS MANUAL AND FOLLOW THE OVERHAUL PROCEDURE OR YOU MAY RISK VOIDING THE WARRANTY.
DUE TO THE CONSTANT TENSION AND FORCES TO WHICH THE REAR DERAILLEUR/HANGER BOLT ARE EXPOSED, THEY REQUIRE REGULAR
HANGER BOLT
INSPECTION AND TIGHTENING. MOST BICYCLE DERAILLEUR HANGERS USE A 5MM HEX, HOWEVER THRU-AXLE DROP-OUTS AND OTHER
DERAILLEUR SYSTEMS MIGHT NEED SPECIAL TOOLS/TIGHETNING PROCEDURES. PLEASE ALWAYS REFER TO THE MANUFACTURERS OWNER
MANUAL BEFORE PROCEEDING.
PEDALS
MAKE SURE YOUR PEDALS ARE ALWAYS PROPERLY TIGHTENED WITH THE HELP OF AN 15MM PEDAL WRENCH OR HEX KEYS. IT IS IMPORTANT TO ALWAYS REMEMBER THAT THE NON-DRIVE SIDE IS ALWAYS REVERSE THREADED. MAKE SURE YOU ALWAYS LUBRICATE/GREASE
THE THREADS PRIOR TO INSTALLATION, AND REFER TO THE MANUFACTURERS OWNER MANUAL TO DETERMINE IF A WASHER BETWEEN
THE PEDAL AND CRANK-ARM INTERFACE IS REQUIRED BEFORE TIGHTENING TO THE PROPER TORQUE.
CHAIN WEAR
DUE TO THE CONSTANT TENSION AND FORCES THE CHAIN IS ALWAYS UNDER, HAVING A WORN-OUT CHAIN MIGHT GENERATE NOISES FROM
THE ENTIRE DRIVE-TRAIN. ON TOP OF BEING NOISY, AN USED CHAIN WILL DETERIORATE THE CHAINRING AND CASSETTE LIFE. WE RECOMMEND YOU MEASURE YOUR CHAIN-WEAR WITH PROPER TOOLS OFTEN TO MAXIMIZE YOUR OVERALL DRIVE-TRAIN LIFE.
CASSETTE ASSEMBLY
DUE TO THE CONSTANT TENSION AND FORCES THE CHAIN IS ALWAYS UNDER, HAVING A LOOSE CASSETTE ASSEMBLY CAN GENERATE LOUD
CREAKING NOISES WHEN PEDALING. PLEASE REFER TO THE MANUFACTURERS OWNER MANUAL FOR PROPER INSTALLATION/MAINTENANCE PROCEDURES.
DUE TO THE CONSTANT BRAKING FORCES V-BRAKES/DISC-BRAKES ARE ALWAYS UNDER, LOOSE BOLTS WILL GENERATE A LOT OF VIBRA-
BOLTS
TIONS THROUGHOUT THE FRAME WHICH CAN EVEN BE TRANSFERED TO LOUD NOISES WHEN APPLYING THE BRAKES. MAKE SURE TO APPLY
BLUE LOCTITE TO THE MOUNTING HARDWARE THREADS BEFORE TENSIONING TO THE MANUFACTURERS SPECIFICATIONS.
SQUEAKS N CREAKS | D E V I N C I T E C H
6
6
COCKPIT ASSEMBLY
1
EVERY SINGLE-BOLT SEATCLAMP ON A DEVINCI BICYCLE REQUIRES A HIGH TORQUE. THATS WHY A TORQUE WRENCH MUST BE USED TO
POST CLAMP
OBTAIN PROPER TORQUE SPECIFICATIONS, OTHERWISE A LOUD CREAKING NOISE CAN BE HEARD WHILE PEDALING SEATED ON THE SADDLE.
SEAT CLAMP
WHEN QUICK-RELEASE SEATCLAMPS ARE USED, MAKE SURE THE BOLT IS ADJUSTED SO THAT PROPER TIGHTENING FORCE IS APPLIED
MAKE SURE YOU SLIGHTLY GREASE ALL METAL-TO-METAL CONTACT POINTS, ESPECIALLY THE MECHANISM CLAMP BOLTS.
2
WHEN THE LEVER IS IN THE CLOSED POSITION. WHEN BOLT-ON SEATCLAMPS ARE USED, MAKE SURE THE BOLT IS PROPERLY TIGHTENED.
KEEP IN MIND NOT TO USE GREASE ON CARBON SEATPOSTS AND/OR FRAMES; USE SPECIAL CARBON ASSEMBLY PASTE INSTEAD. PLEASE
ALWAYS REFER TO THE MANUFACTURERS OWNER MANUAL FOR PROPER TORQUE SPECIFICATIONS.
3
STEM BOLTS
AS PART OF THE COCKPIT ASSEMBLY, STEM CAP BOLTS SHOULD BE INSPECTED OFTEN TO MAKE SURE PROPER TORQUE IS APPLIED AS
REFERENCED IN THE STEM OWNERS MANUAL. DO NOT USE GREASE ON CARBON STEER TUBES AND CARBON HANDLEBARS, ALWAYS
REFER TO THE PARTS OWNER MANUAL FOR PROPER INSTALLATION.
HEADSET
IN ORDER TO WORK PROPERLY, THE HEADSET ASSEMBLY REQUIRES THE STEM BOLTS TO BE TIGHTENED TO SPEC TO KEEP EVERYTHING
TIGHT AND SECURE. FOR CARBON STEER TUBES, A PROPER CARBON SPECIFIC EXPANDER PLUG NEEDS TO BE USED INSTEAD OF A REGULAR STAR NUT. PLEASE ALWAYS REFER TO THE MANUFACTURERS OWNER MANUAL FOR PROPER ASSEMBLY.
SUSPENSION ASSEMBLY
5
DRY SHOCK BOLTS AND/OR LOOSE SHOCK BOLTS CAN GENERATE SOME NOISE IF NOT TAKEN CARE OF. WE RECOMMEND LUBRICATING THE
TING HARDWARE
SHOCK BOLTS BEFORE ASSEMBLY, AND MAKE SURE TO APPLY SOME BLUE LOCTITE ON DRY AND CLEAN THREADS BEFORE TORQUING TO
SPEC.
SUSPENSION PIVOT
EACH AND EVERY PIVOT BOLT SHOULD BE TORQUED TO ITS PROPER SPECIFICIATION WITHIN THE DEVINCI SPLIT-PIVOT MANUAL. IN MOST
BOLTS
ENVIRONMENTS, LUBRICATINGS THOSE PIVOT POINTS AND BOLTS SHOULD ELIMINATE ANY CREAKING ISSUES WITHOUT THE NEED FOR
BEARING EXTRACTION. IF NOISES PERSIST AFTER LUBRICATION, PLEASE VISIT YOUR LOCAL DEVINCI AUTHORIZED DEALER FOR BEARING
REMOVAL/INSTALLATION AND OVERHAUL PROCEDURES (SPECIAL BEARING EXTRACTOR NEEDED).
SQUEAKS N CREAKS | D E V I N C I T E C H
WHEEL ASSEMBLY
1
QUICK-RELEASE
WHEEL QUICK RELEASES SHOULD ALWAYS BE UNDER PROPER TENSION AND PROPERLY FASTENED. THERE SHOULD BE AMPLE RESISTANCE
SKEWERS
WHEN TRYING TO OPEN THE QUICK RELEASE, IF NOT, TURN THE BOLT UNTIL A SIGNIFICANT AMOUNT OF FORCE IS REQUIRED TO CLOSE THE
QUICK RELEASE. MAKE SURE TO CHECK THE TENSION ON EACH QUICK RELEASE BEFORE AND AFTER EVERY BIKE RIDE.
REAR WHEEL
THREADED AXLES
MAKE SURE TO LUBRICATE/GREASE THE REAR AXLE AND ITS THREADS BEFORE TENSIONNING IT TO ITS PROPER TORQUE. FAILURE TO
PERFORM THESE ACTIONS WILL RESULT IN EITHER A LOOSE AXLE, SEIZED AXLE AND/OR CREAKING NOISES WHEN PEDALLING FORCES ARE
APPLIED.
MISC ASSEMBLY
3
AS SIMPLE AS THEY ARE, WATER BOTTLE CAGES WHEN NOT TIGHTENED PROPERLY CAN GENERATE RATTLING NOISES. REFER TO THE
MANUFACTURERS OWNER MANUAL FOR PROPER INSTALLATION AND TORQUES.
SQUEAKS N CREAKS | D E V I N C I T E C H
OWNERS
MANUAL
FOR
MULTI-SPEED
BICYCLES
This manual contains important safety, performance and maintenance information. Please read this manual before you take your first ride on your new
bicycle. Keep the manual handy for future reference.
Pour obtenir une version franaise de ce document, communiquez avec nous via Internet ladresse : service@devinci.com
NOTE: This manual is not intended as a comprehensive use, service, repair or maintenance manual. If you have any questions about your bicycle
which are not answered in this manual, of if you are not certain that you understand any of the answers in this manual, please consult with your
authorized Devinci dealer.
01
IMPORTANT WARNING
Most sports carry the risk of injury, damage or both, and bicycling is no exception. By choosing to ride a bike, you are aware of these inherent dangers and risks. You also agree to take full
responsibility for those risks. Neither the manufacturer, nor the distributor, nor the person who sold your bike, nor the people that do the maintenance of the trails where you ride can be held
responsible. Since you take full responsibility, it is imperative that you read and fully understand the content of this manual.
It is your duty to do the proper maintenance on your bicycle and, therefore, substantially reduce the risk of injury.
Riding a bicycle can be a very dangerous activity, even under the best circumstances. Also, since it is impossible to predict all the situations you may face, this manual is not meant to describe
every aspect of safe use. Many risks inherent to riding a bike cannot be predicted or avoided and they are, therefore, your sole responsibility.
This manual uses WARNING and CAUTION tabs that warn you about consequences that might occur because of bad inspection or inadequate maintenance of your bicycle. Also, not
respecting traffic laws can lead to serious injury or damage. The symbol
and the word WARNING always indicate risk of serious injury that could even lead to death. The symbol
and the word CAUTION imply the possibility of serious damage to your bicycle and the risk of voiding your warranty.
Warning intended for parents and guardians
It is tragic to realize that minors are the most likely to be involved in bicycling accidents. As parent or guardian, you are entirely responsible for your childrens activities and therefore of their
security. Those responsibilities consist, among other things, of making sure that the following criteria are met:
As the parent or the guardian, you should read this manual in its entirety before letting your children use the bike. Moreover, make sure your child always wears a regulation standard helmet
when bicycling.
02
YOUR AUTHORIZED
DEVINCI DEALER
Your authorized Devinci dealer is committed to guiding you in the process of choosing a bike with accessories that really are adapted to the type of cycling you wish to practice. It also provides
help concerning maintenance, so you can fully benefit from your investment. Authorized Devinci staff possess the knowledge, the experience and the necessary tools to adequately repair and
provide reliable advice.
However, your dealer cannot make decisions on your behalf and be held responsible for your lack of knowledge, experience, qualifications or common sense. On the other hand, your
authorized Devinci dealer can take the time to explain how your bike and its components work or what accessories will meet your specific needs.
If you have a problem or need information, consult your authorized Devinci dealer immediately, who will be glad to answer and guide you.
03
NOMENCLATURE
FOR YOUT BIKE
31 27
38
33
35
30
1
34
6
20
5
19
21
13
26
24
22
2
4
25
28
29
32
23
17
36
18
10
11
12
14
15
37
16
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
Frame
Top tube
Down tube
Seat tube
Chain stay
Seat stay
Head tube
Fork
Wheel
Tire
Tread
Sidewall
Valve
Inner tube
Rim
Spokes
Hub
Quick release
Bottom bracket
Crank
04
4.1 Road
The term road bike refers to any bicycle designed for paved roads or paths. Like most products that grow in popularity, so does their
design to meet the specific demands of the consumer. The road bike can be further divided into four types: Road, Time-trial/Triathlon,
Touring and Cyclo-cross.
4.2 All-terrain
The term all-terrain refers to any bicycle designed for off-road riding. Since the beginning, off-road riders have pushed the limits of their
bikes and begun to ride a wider variety of terrain, forcing the market to split into four categories of mountain bikes: XC racing, XC Trail,
Freeride and Downhill.
4.3 Hybrid
The desire to ride freely on a comfortable bike, both on cycle paths and in the city, has led to both on cycle paths and in the city, has led
to bike and the mountain bike, the hybrid is well-adapted to touring trips or your daily transportation to work. The hybrid offers a wide
range of gear ratios and large wheels for a smoother ride than the road bike and a faster one than the all-terrain.
4.4 Comfort
The comfort bike is meant for those who enjoy life on the paved paths. With larger tires than the hybrid bike and a more comfortable
saddle, it allows a straighter position for riders looking for a pleasant and safe ride. The comfort bike is an excellent choice for cyclists
that prefer comfort over speed.
05
FUNDAMENTALS OF CYCLING
It is strongly recommended that you read this manual thoroughly before your very first ride. Make sure you understand the following points and be sure to refer to the detailed sections if you
have any doubts. Remember that your authorized Devinci dealer is also available to answer your questions.
5.1.1 Bike Dimensions
First, you should know the answers to the following questions:
a. Is the size of your bike adequate for you? To check, refer to section 5.2.1. A bike thats too large or too small results in loss of stability and could make you fall.
b. Is your saddle properly adjusted? To check, refer to section 5.2.2. Before adjusting the saddle by yourself, make sure you respect the minimal insertion height by referring to section 7.2.
c. Have you correctly tightened the saddle and the seat post? If so, you shouldnt get any movement whatsoever.
d. Are the handlebars and the stem in the right positioned for you? Before adjusting, make sure you refer to section 5.2.3 to learn how to do it the right way.
e. Are the reach and angle of your brakes convenient for you? It is possible to adjust your brakes to make them more comfortable to use. Please refer to section 5.2.4.
f. Do you know precisely how everything works on your bike? If you to have any doubts, do not hesitate to contact your authorized Devinci dealer who will be pleased to describe and teach
the functioning of every mechanism to you.
5.1.2 Security and Bicycling
a. A regulation standard helmet by CSA (Canada), CPSC, Snell, ASTM (America) or CEN (Europe) is an essential piece of equipment. Do you have one? It is imperative that you ALWAYS
wear a regulation standard helmet when riding your bike. Also, make sure it fits your head, that it is well-adjusted and that the chin strap is securely buckled. The use of a poorly
adjusted, wrongly positioned and/or incorrectly attached helmet may cause serious injury and could even lead to death.
b. Do you own other specific safety equipment? In certain provinces or states, you may be obliged to use other safety equipment. It is your responsibility to know and respect the safety
rules in effect wherever you ride your bike.
c. Are you familiar with the use of your wheel quick releases? If not, make sure you refer to section 7.1 to understand their functioning. The use of a bike with incorrectly adjusted wheel
quick releases is very dangerous since the wheel could become loose or even unlock and fall, causing damage and/or serious injury that could lead to death.
d. Do you know how to operate toe clips or clipless pedals? If your bike is equipped with one or the other device and you dont fully understand their functioning please refer to section 7.6
or 7.7. It is very important that you acquire the skills to safely engage and disengage these pedal models. In order to do so, you need to take time in a safe place to practice and learn
how they work, one foot at a time. The technique is tricky at first and there is a risk of falling, which could cause injuries.
e. Is your bike equipped with a front suspension? If so, refer to section 7.8. When braking, a weight transfer tends to compress the front suspension, resulting in a lifting force applied to the
rear of your bike that could throw you over the handlebars. It is important that you learn how to use a bike equipped with suspensions in a safe place before doing a real ride. Consult your
suspension user manual for more information on how to adjust your suspension. Safety mechanical inspection.
It is crucial that you make a rigorous mechanical inspection before using your bike. Refer to section 5.4 to find out precisely what has to be checked.
Congratulations, you are now up for your first ride!
Wearing your helmet, go get acquainted with your new bike. We recommend you do a short ride to familiarize yourself with the operations of all the different components.
Make sure you learn to brake, to shift gears, engage and disengage your toe clips or clipless pedals as well as understanding how your suspension responds and operates. This learning
curve is inevitable and will make you appreciate much more the rides that follow by making them safer at the same time.
Dont forget to read the manual in its entirety!
Figure 1
Figure 2
Figure 3
Figure 6
Figure 4
Figure 5
Figure 7
In order to adjust the height of your saddle, you will need to loosen the quick release of the seat collar bolt, referring to figure 6 to determine which one you have. Then, move the seat post
up or down according referring to figure 6 to determine which one you have. Then, move the seat post up or down according to your needs. Check the straightness of the saddle with
respect to the length of the bike and tighten the seat collar carefully to firmly immobilize the seat post.
WARNING: Your seat post has a minimum insertion line which limits the maximum height you can safely reach. Under no circumstances should this line be visible after
positioning the saddle (see figure 7). Placing the saddle otherwise could result in a rupture of the seat tube inducing a loss of control that could lead to serious
injury or even death.
B. The Fore-and-aft positioning
Loosen the clamp by referring to figures 3, 4 and 5 and slide the saddle toward the front or the back as desired. First, place the saddle in the middle and make it slide in the desired
direction until the most comfortable position is reached.
C. The Tilt
Even though many cyclists opt for a horizontal saddle, a few prefer to have it tilted. If this interests you and your saddle allows it (see figure 5), just loosen the saddle clamping mechanism
and tilt the saddle as desired. Be sure to tighten back the mechanism firmly.
WARNING: After moving your saddle, tighten the clamping mechanism vigorously and do it before attempting to ride your bike. In order to make sure it is properly
clamped, grab the two ends of your saddle and try to move it up, down, sideways, try to tilt it and even twist it every possible wayIf it moves, contact your
authorized Devinci dealer.
Small changes in your saddle positioning are enough to increase both your comfort and performance levels. It is strongly recommended that you adjust the saddle in one direction at a time.
Do it many times, little by little, until you find the best position for you.
If you have not found a comfortable configuration after adjusting your saddle in every direction, maybe another type of saddle would suit you better. Everyone is different and that could
explain the abundance of different saddle models on the market, offering a myriad of sizes, shapes and stiffness. Your dealer can guide you in the process of choosing an appropriate
saddle that will suit your needs and expectations.
CAUTION: Riding a bike equipped with a saddle that does not correctly support your pelvic area can induce pain or numbness. Also, injuries to your nerves and to your
blood vessels could result from an inappropriate saddle. If you happen to feel pain or numbness, adjust your saddle differently. If it persists, contact your
authorized Devinci dealer to find out about ergonomic models that might suit you better.
5.2.3 Handlebar positioning
If your bike has a stem clamped directly on the outside of the steer tube, your authorized Devinci dealer should adjust your handlebars height by using cylindrical spacers above or under it.
Do not attempt this modification by yourself, ask your authorized Devinci dealer instead.
Figure 8
Figure 9
On many bikes, it is possible to adjust the height of the handlebars slightly yourself by changing the stem height. To do so, loosen the stem clamping bolt by a few turns as shown on figure
9. Use a rubber hammer to move the stem if it appears to be jammed. You can now adjust the height of the stem and tighten back the bolt properly once you have reached the desired
setting. You should never be able to move the alignment of the handlebars and the stem with your hands. Moreover, there is a minimum insertion line on your stem; make sure it is never
visible. It is not recommended to make this modification by yourself, this one requires a certain amount of experience. Ask your authorized Devinci dealer if youre in doubt.
Now check if your handlebars turn normally and that your brakes are working properly.
CAUTION: On a few bike models, the handlebars height adjustment could modify the tension in the front brake cable, resulting in the malfunctioning of your front brakes.
If the brake pads are closer or further apart from the rim, contact your authorized Devinci dealer before using your bike to have your brakes adjusted.
WARNING: The minimum insertion line of your stem shall not be higher than the head set as shown on figure 9. If visible, there is a risk of damaging your steer tube which
could result in a loss of control and a fall, leading to serious injury or even death.
If you wish to modify the angle of your handlebars, you can loosen the bolt of its clamping system, rotate the handlebars as desired, center them and tighten the bolt vigorously. You
shouldnt be able to change the alignment of the handlebars with the stem with your hands.
WARNING: A weak tightening of the retaining bolt of your stem or of the handlebars is likely to decrease the handling of your bike and risk causing a loss of control and a
fall. Place yourself facing the bike, squeeze the front wheel between your legs and try turning the handlebars. If you can change the alignment between your
stem and your front wheel, the bolts are definitely not tightened enough. The alignment of the handlebars with respect to the stem should also be identical.
5.2.4 Brake levers and shifters position
Upon delivery of your bike, your authorized Devinci dealer has assembled the brake levers and shifters in the standard position. It is possible to modify their angle and their position with
respect to the handlebars. Ask your authorized Devinci dealer to adjust them or to show you the procedure.
5.2.5 Brake tuning
Many models offer the possibility of adjusting the reach of your brake levers and shifters. If you feel it is difficult to brake or to shift gears properly, then ask your authorized Devinci dealer
to adjust them according to your needs.
WARNING: It is essential that all your stopping power is available within the reach that the brakes are adjusted in. As a matter of fact, a shorter brake reach implies a
thinner functioning range. Indeed, an insufficient reach could prevent the use of your maximum braking power, which can lead, of course, to loss of control,
falls, serious injury or even death.
Figure 10
Make sure the helmet you choose is well-adapted to your head, not to your look. Always place it correctly as shown on figure 10 and secure it completely. Ask your authorized Devinci
dealer to guide you in the process of selecting your helmet.
WARNING: You should always wear a regulation standard helmet when riding your bike. It is important to secure the chin strap. Consult your helmet user manual for more
information. The use of a regulation standard helmet can prevent serious or even deadly injury
5.3.2 Reflectors
The reflectors are an essential component of your bike that greatly improve your safety. They are designed to reflect car lights and street lights and therefore, make you easier to spot.
WARNING: Run a regular check to verify that your reflectors and their mounting brackets are functional, clean, straight and solidly mounted. Consult your authorized
Devinci dealer if they are broken or damaged, to get them replaced.
WARNING: Never remove your front or rear reflectors or their mounting brackets, because they are designed to push away from the brake cables and prevent interference
with the wheels in the event they break. Such interference could result in sudden wheel stop, leading to loss of control that could cause serious or even deadly
injuries.
WARNING: Never remove your bike reflectors. They are very important safety devices that help increase significantly your visibility. Indeed, if you remove them, there is a
risk of collision between you and the other road users who will not see you properly. Being hit by a car can result in very serious injuries or even death.
However, do not forget that reflectors are not intended to replace lights. Be sure to equip your bike with lights according to the local legislation.
5.3.3 Lights
If you use your bike at night, it has to be equipped with lights to make your surroundings visible and make you visible to your surroundings. From a legal point of view, a bicycle is as much
a road vehicle as a car. Therefore, you are required to have a white front light and a red one on the back, when riding at night. Your authorized Devinci dealer can guide you in choosing the
proper lighting devices.
WARNING: The reflectors are not intended to replace lights. You are required to equip your bike with lighting devices according to the legislation in effect in the areas
where you use it. It is dangerous to ride without reflectors and lights at night or when the visibility is poor.
5.3.4 Pedals
Performance bikes are often equipped with pedals with sharp edges and dangerous parts. These are designed to increased security and performance by improving their adherence with
the cycling shoes. If you have this pedal type, be careful and practice their use on an unpaved surface. Depending on your level, you might want to choose a less aggressive pedal model.
Consult your authorized Devinci dealer to choose a convenient pedal model.
5.3.5 Eyewear
When riding a bike, there is a high risk of getting dust, mud, bugs and other projectiles in the eyes. Therefore, it is strongly recommended that you wear eye protection adapted to riding.
Consult your authorized Devinci dealer to receive assistance choosing your eyewear.
06
07
TECHNICAL INFORMATION
In order to increase your performance, your safety as well as your fun, it is essential that you understand thoroughly how your bike and its components work. Even if you are an expert rider, the
new generation bikes have so many innovations and new technology that you could end up surprised. It is, therefore, strongly recommended you go through this section no matter how much
experience you have. For more information, always refer to your authorized Devinci dealer.
7.1 Wheels
7.1.1 Assembly and disassembly
WARNING: Using a bike with quick releases that are not tightened enough means you risk losing the wheels, resulting in damage to bike and leading potentially to serious
injury or even death. It is, therefore, essential that you:
1. Ask your authorized Devinci dealer to explain how the wheels quick releases work so that you can assemble and disassemble them safely;
2. Learn how to safely use a quick release so that you can apply this knowledge;
3. Make sure your wheels are properly clamped before every ride.
A. Adjusting the quick release system
The quick release uses a cam mechanism to exert a significant force on the wheel hub when placed in the closed position and a small force in the open position. Since it is adjustable, you need
to learn how to operate it to ensure optimal use and a safe binding.
Figure 11
WARNING: You need to use the cam mechanism when clamping your wheel with a quick release to achieve proper binding force, by switching the lever from the opened to the
closed position. If you hold the level with one hand and you screw the nut to clamp the wheel, it will never be safely tightened. Instead, you need to switch the lever
from the opened to the closed position with a very significant restriction force. The nut helps you adjust the amplitude of that force by screwing or unscrewing it.
It is the power of the cam that maintains the wheel in place. It squeezes the wheel hub in between the fork arm ends or dropouts when switching the lever from the opened to the closed
position. The tightening force depends on the torque applied on the adjusting nut. To increase the tightening force, you need to turn the adjusting nut clockwise while holding the lever with the
other hand. To reduce it, turn the adjusting nut counterclockwise again holding the lever. Less than half a turn can make the difference between a safe and an unsafe tightening. Refer to
figure 11.
Notice: The quick release mechanism is installed on the wheel hub by its manufacturer. Never remove the mechanism from the wheel hub unless you need to repair it. Consult your authorized
Devinci dealer for the repair of a wheel hub.
B. Front wheel alternative devices
On many models, the front fork is equipped with an alternative retention device that prevents the wheel from disengaging in case of poor quick release installation. This device, integrated
directly to the fork by the processes of machining or casting, shall not replace, under any circumstances, the prescribed adjustment of the quick release.
WARNING: It is very dangerous to use a bike with a modified or removed auxiliary retention device. The modification or the removal of this device could result in serious injury
or even death. This could also lead to the annulment of your warranty.
C. Disassembly and assembly of a wheel equipped with a quick release
a. Front wheel disassembly
i. If your bike has v-brakes, spread the brake calipers as elaborated in section 7.3;
ii. Switch the quick release from the closed to the opened position;
iii.Loosen the adjusting nut of the quick release until the wheel can be adequately removed;
iv.Lift the front of the bike a few centimeters and hit the wheel downward with your hand to disengage it from the fork.
Figure 12
Figure 13
Figure 14
WARNING: The auxiliary retention system is not intended to replace adequate tightening of the quick release. If you use your bike and the quick releases are not tightened
enough, you risk losing the wheels, damaging your bike and suffering serious injury or even death.
c. Rear wheel disassembly
i. Shift the rear derailleur onto the highest gear corresponding to the smallest sprocket;
ii. If your bike has v-brakes, spread the brake calipers as shown in section 7.3;
iii.Turn the quick release lever to the opened position as illustrated in figure 12;
iv. Lift the rear of the bike a few centimeters and push the wheel Lift the rear of the bike a few centimeters and push the wheel disengage it.
d. Rear wheel assembly
Notice: If your bike has disc brakes, make sure you do not damage the disc, the calipers or the pads in the process of replacing the front wheel. Be particularly careful when inserting the disc
between the brake pads and the calipers.
i. Shift the rear derailleur on to the highest gear which corresponds to the smallest sprocket;
ii. Shift the rear derailleur on to the highest gear which corresponds to the smallest sprocket;
Turn the quick release lever to the opened position, referring to figure 12. Place the wheel with the quick release positioned on the rear derailleurs opposite side;
iii.Bring the derailleur body towards the back with one of your hands;
iv.Place the chain on the smallest sprocket of the cassette. Position the wheel axel in the dropouts and push vigorously as shown on figure 14;
v. Turn the adjusting nut clockwise until it touches the dropout. Turn the quick release lever towards the closed position, making sure the lever is parallel to the seat stay;
WARNING: The auxiliary retention system is not intended to replace adequate tightening of the quick release. If you use your bike, and the quick releases are not tightened
enough, your wheels risk to disengaging, damaging your bike and leading to serious injury or even death.
vi.If you cannot tighten the quick release lever to the closed position, you need to loosen the adjusting nut a quarter of a turn. Then try again;
vii. Place the rear derailleur back in place;
viii. Reconfigure the brake back in place and make sure the wheel is properly centered so that it turns freely without rubbing the brake pads.
D. Assembly and disassembly of wheels without quick release
a. Front wheel disassembly
i. If your bike has v-brakes, spread the brake calipers as elaborated in section 7.3;
iii.Lift the front of the bike a few centimeters and hit the wheel downward with your hand to disengage it from the fork.
b. Front wheel assembly
i. Place the fork straight with respect to the bike and insert the wheel between the fork dropouts. The axel must firmly rest in the dropouts. The washers should be on the outside of the
dropouts, before the nuts;
ii. Press the wheel firmly in the dropouts and align the wheel with respect to the fork. Tighten the nuts firmly on the axel with a 15mm wrench;
iii.Reconfigure the brake back in place and make sure the wheel is properly centered, so that it turns freely without touching the brake pads.
7.2 Seatpost
Most bikes have a quick release to clamp the seatpost. These work exactly like the wheel quick releases as explained before. Even though it looks like a bolt with a nut and a lever, it is
actually a cam mechanism that clamps your seatpost tightly and that facilitates adjusting its height.
WARNING: If you use your bike and its seatpost quick release is not tightened enough, your seat could move and turn. This could result in a loss of control, leading to
serious injury or even death. It is, therefore, essential that you:
1. Ask your authorized Devinci dealer to explain how your quick release works so that you can safely adjust your seat;
2. Learn how to safely use a quick release so that you can apply this knowledge;
3. Make sure your seat is properly clamped before every ride.
A. Quick release adjustments
It is the power of the cam that maintains the seatpost in place. It squeezes it inside the seat tube when switching the lever from the opened to the closed position. The tightening force
depends on the torque applied on the adjusting nut. To increase the tightening force, you need to turn the adjusting nut clockwise while holding the lever with the other hand. To reduce it, turn
the adjusting nut counterclockwise while hold ing the lever. Less than half a turn can make the difference between a safe and an unsafe clamping.
WARNING: You need to use the cam mechanism when clamping your seatpost with a quick release to achieve proper clamping force, by switching the lever from the opened
to the closed position. If you hold the nut in one hand and you turn the lever to tighten the wheel, the seatpost is never going to be safely clamped. Instead, you
need to switch the lever from the opened to the closed position with significant restriction force. The nut helps you adjust the amplitude of that force by screwing
or unscrewing it.
WARNING: To place the quick release lever into the closed position, you must use leverage with the seat tube. Also, the lever should leave a clear imprint in the palm of your
hand for a few seconds. If this not the case, place the lever back to the opened position and turn the adjusting nut a quarter of a turn clockwise and try again.
7.3 Brakes
Notice: In order to achieve the optimal braking power, use both front and rear brakes simultaneously.
WARNING: If you brake suddenly and excessively, you risk falling over your bike and that could cause serious injury or even death.
7.3.1 Brake functioning
First of all, for safety purposes, it is essential you instinctively associate each brake lever with the brake it controls. In North America, the right lever controls the rear brake while the left one
controls the front one. On a bicycle, it is the friction between the brake pads and the rims that allows braking, by transforming kinetic energy into heat. There are also disc brakes that uses the
same principle but with a disc instead of the wheel rim. In both cases, for the best braking, clean the brake pads and the rim or the disc and make sure there are no traces of lubricant or wax.
Furthermore, you should check that the brakes are easy to reach with your hands. If you feel your hands are too small, that the position is uncomfortable or if you are unable to brake with full
power, ask your authorized Devinci dealer. Most of the time, they will be able to tune the reach of the brake levers or install specific grips to solve the problem.
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Most brakes possess a mechanism that allows disengaging the brake from the rim when you want to assemble or remove the wheel. Once disengaged, it is impossible to brake. Ask your
authorized Devinci dealer to explain clearly how to disengage the brakes on your bike according to the mechanism you have (refer to figures 15 to 19). Always check that your brakes are
operational before using your bike. Brakes are not intended for the sole purpose of stopping your bike, they are also intended to help you slow down. The maximal stopping power can be
achieved just before the wheel starts skidding. When the wheels are locked up, a large amount of the breaking power is lost and you tend to loose control. You must learn to slow down and
brake efficiently without locking up your wheels. This technique is known as progressive braking modulation. Pull the brake lever by progressively increasing the braking power instead of
pulling suddenly and excessively. If you feel your wheels starting to lock, smoothly release the lever until you get a normal wheel rotation back. It is very important to adjust the braking force
on the wheels according to the surface on which youre riding. To thoroughly understand this technique, we recommend you try walking beside your bike to visualize the effect of pulling the
brake levers. You are likely to perceive more easily the moment your wheels lock up and stop rotating.
WARNING: The disc and linear pull brakes on certain models are extremely powerful. If you have this kind of brakes, familiarize yourself carefully by trying to brake
progressively at first. Pull the lever too suddenly could result in loss of control and a fall.
CAUTION: Disc brakes become very hot after intensive or prolonged use. Be careful not to burn yourself by touching the disc or the caliper.
When braking, the bike starts slowing down, but your body inertia tends to continue forward at the same pace, causing a weight transfer towards the front wheel. If you brake by suddenly
locking up the wheels, this weight transfer could throw you over the handlebars. This phenomenon will even be accentuated if you have a front suspension. Indeed, the suspension will
compress downward, increasing the weight transfer.
Another factor that affects the braking force is the load on your wheel. Indeed, normal force is directly proportional to the friction force you can reach. As a matter of fact, a wheel with a
heavy load on it will allow a higher braking force, while a wheel with a lighter load on it will lock up much sooner. Therefore, you should back up to the rear of your bike when braking with
more intensity. This will increase the weight on the rear wheel while decreasing the weight on the front one, it will also shift your center of gravity. This will help reduce the risk on being
thrown over your bike. Simultaneously , you should use the front brake with more strength than the rear one. This technique is even more important when riding down steep terrain.
In order to master braking techniques, it is important to practice in a safe place away from traffic, obstacles or any other danger. Make sure you master the lock up limits of your wheels and
the weight transfer linked to emergency braking.
When riding your bike on wet surfaces, in rainy weather or on light and running soil, your bike response changes. The tire adherence decreases quickly and your maneuverability is
negatively affected. Often, a smaller braking pressure is all it takes to lock up the wheels completely. Furthermore, water and humidity make the brake pads less efficient. In wet weather,
make sure you reduce your speed in order to better control your bike.
7.3.2 Brake tuning
If your bike is equipped with hydraulic disc brakes and you suspect something abnormal at your safety mechanical inspection, have it immediately checked by your authorized Devinci dealer.
On the other hand, if your bike is equipped with cable brakes and it fails the safety mechanical inspection, you can try adjusting their strokes by turning their tuning barrel counter-clockwise.
Make sure you screw back the lock nut after the adjustment. If the problem persists, ask your authorized Devinci dealer for assistance. Refer to figures 20 and 21 for visual support.
A rear derailleur;
A front derailleur (most of the time);
A freewheel cassette;
One to three chainrings;
A chain;
One or two shifters.
To calculate the number of speeds available on a bike, just multiply the number of chainrings with the number of rear sprockets on your freewheel cassette. For example, a bike with three
chainrings and nine sprockets on your freewheel cassette has twenty-seven speeds.
A. Shifting gears
Many shifter models are available on the market. Devinci has selected shifters to better meet your criteria in terms of ergonomics, performance and price. The figures 22 to 25 illustrate the
way the different models work. Check the type of shifters your bike is equipped with before continuing.
Figure 22
Figure 24
Figure 23
Figure 25
The vocabulary for gear shifting might seem a bit confusing at first. To go to a shorter gear ratio or to a slower gear is designated as a downshift while upshifting refers to the action of going
at a longer gear ratio or a faster gear. A slower gear requires less strength than a faster gear. To make that even more complex, the actions on your rear derailleur are opposite to those on
your front derailleur. Indeed, the action of down shifting can be achieved in two different ways; lowering the chain on a smaller chainring or raising the chain on a larger sprocket on the
freewheel cassette. Refer to sections B and C for more details.
A little trick to help you memorize this is to note that the chain must be closer to the frame in order to down shift and climb a hill or further away to upshift and go faster.
To shift gears, the chain must be tight and rotate in the normal direction. The derailleur works only when pedaling forward.
CAUTION: Never activate your shifters when pedaling backwards and never pedal backwards after having shifted gears. The gears could jam and damage your bike.
WARNING: Never send the chain on the larger or the smaller sprocket of the freewheel cassette if your derailleur is not properly adjusted. The chain could jam and result in
a fall and serious injury. This also applies to the front derailleur.
Figure 26
Figure 27
As mentioned earlier, your tire sidewall indicates an interval of recommended tire pressure. The maneuverability of your bike on different soils largely depends on your tire pressure.
When inflated to the maximal pressure, your tire offers less resistance and friction. However, this damps impacts. Maximum pressure is recommended on a dry and smooth surface. At the
minimum pressure, tires offer better results on smooth or slippery surfaces like compact argyle or light and running soil.
If your tire pressure is insufficient for your weight or riding style, the tire could deform and pinch the inner tube which could result in a tire puncture.
WARNING: The pressure readings from gas station compressor units are often inaccurate and so are many automotive tire gages. Do not rely on these devices, unless
you are confident of their precision. Make sure you always use a quality manometer that provides good and accurate results.
Refer to your authorized Devinci dealer to learn about the tire pressure you should have, according to your riding habits, and inflate your tires accordingly. To check, refer to section 5.4.2.
You will then have a visual benchmark to refer to when inspecting your tire pressure. Make sure you check it frequently since it can change quickly.
Some high-end tires have specific direction of rotation. Indeed, their tread is designed to provide a better adherence in a specific direction. In that case, an arrow on the sidewall indicates
the proper direction. Make sure the wheels are properly mounted to respect the rotating direction as you go forward.
7.5.2 Valves
Valves allow inflating your tires inner tubes and keeping their pressure at the same time. Two valve models are available on the market; the Presta and the Schraeder shown on figures 28
and 29. You need a pump that is compatible with the valve model that your tires are equipped with. Adaptors exist to make the Presta valves fit the Schraeder standard.
The Schraeder valve is the same used by the automotive industry. To inflate a Schraeder valve tube, all you need to do is to unscrew its cap and use a bicycle pump or a compressor. To
deflate it partially or completely, just press on the tiny pin in the middle of the valve end with a sharp-pointed object. Always have the valve caps properly hand-tightened before using your
bike.
Figure 28
Figure 29
The Presta valve has a smaller diameter than the Schraeder and can only be found on bicycle tires. To inflate a Presta valve tube, you need a pump equipped with a Presta head. Remove
the cap, unscrew its small retaining nut and press down the small pin to set it free. Insert your pump head on the valve end and just inflate the tube. However, if you wish to inflate a tube
using a compressor, you are going to need a Presta adaptor. Ask your authorized Devinci dealer for one. The adaptor can be screwed on the valve end once the small retaining nut is
loosened. To diminish the pressure inside your Presta valve tube, unscrew the retaining nut and press it down until you have reached the desired pressure. Tighten the retaining nut and
place your cap back before using your bike.
7.6 Toe-clips
Toe-clips are intended to help cyclists maintain their feet in place on their pedals. Furthermore, the toe-clip allows you to adequately position your foot on the pedal, providing the best
pedaling power Cyclists can tighten the straps to maintain their feet on the pedals during the whole pedaling cycle. The main advantage of this mechanism is to allow the use of any kind of
shoes, even though results are optimal with adapted shoes. Ask your authorized Devinci dealer for more details.
WARNING: You need to have specific skills to get on and off a bike that has toe-clips. These skills are earned through practice. Before becoming a reflex, this technique is
likely to require all your concentration. Practice using the toe-clips in a safe place where there is no traffic, obstacles or any other risk. Make sure you learn to
use them with loose pedal straps and do not tighten them before mastering the technique. Never ride in traffic with tightened straps.
7.8 Suspension
All all-terrain bikes have suspension systems. These are designed to help absorb the shocks and impacts encountered while riding off-road. There are many suspension models on the
market and to elaborate on each of them would be futile and too exhaustive for this manual. If your bike is equipped with a suspension system, refer to your authorized Devinci dealer for
details regarding its maintenance and tuning.
A suspension improves the comfort, stability and maneuverability of your bike. This helps you ride faster on the mountain biking trails. But do not rely only on your bikes superior ability to
attack difficult courses. Make sure you also know your own limits. You need to spend lots of time and sweat to increase your riding skills.
WARNING: If your suspension is maladjusted or poorly maintained, it could malfunction and that could result in a loss of control and a fall.
CAUTION: By adjusting a suspension, you risk affecting your bike braking and handling capacities. Never try to adjust suspension settings without having previously
studied the manufacturers instructions and recommendations. Test your new setting carefully by doing a short ride in safe spot.
CAUTION: Your bike is not meant to be equipped with any suspension models. You should check with your authorized Devinci dealer which suspension systems are
compatible.
WARNING: When equipped with a suspension, your bike is likely to become more dangerous at high speeds. Indeed, braking makes the front suspension compress and
that could result in loss of control and a fall. You should learn to master the behavior of your suspension before try ing to ride on steep terrain and/or at high
speeds.
08
Notice: New technologies now allow the modern bike to become highly efficient but very complex at the same time. This complexity, along with a high number of recent innovations, make it
impossible for us to provide you with all the necessary information you would need to maintain and repair your bike. In order to minimize the risk of accidents and injuries, we strongly
recommend you bring your bike to your authorized Devinci dealer for maintenance and service.
Your authorized Devinci dealer is certainly the best resource to get your bike tuned-up or fixed. Indeed, the maintenance that you can perform yourself depends largely on your skills, your
experience and the tools you have at your disposal.
The maintenance required for your bike is determined by many factors, ranging from your cycling style to your geographical location. Consult your authorized Devinci dealer to identify your
maintenance needs.
WARNING: Many situations you may encounter require very specific knowledge and tools. Do not attempt to tune or fix your bike if you doubt in any way your ability to
finish it. Any error could lead to bike damage and serious injury or even death.
If you wish to learn to repair your bike by yourself, three possibilities lay ahead of you:
1. Ask your authorized Devinci dealer to suggest books that cover bike repair and maintenance;
2. Ask your authorized Devinci dealer to provide you with the manuals of installation and maintenance of the various components your bike is equipped with;
3. Ask your authorized Devinci dealer to inform you concerning bike mechanics classes and training near you.
No matter what your choice ends up being, we advise you to ask your authorized Devinci dealer to in spect the quality of your work before using your bike. This precaution is meant to ensure
that everything is correct and properly functioning. Since this check-up is time-consuming, it is likely that your authorized Devinci dealer will charge a small monetary compensation.
WARNING: A bike and its components sustain the hight levels of reoetitive stresses. The fatigue endurance depends largely on the nature of the materials and their
micrographic structures. If you use a component longer than its standard fatigue like, id risks cracking and then suddenly breaking, causing serious injury or
even death. The apparance of cracks, scratches or discolorations are clues that your bike is fatigued and worn. If you find any of these, immediately ask your
authorized Devinci dealer to evaluate the components and replace them if necessary.
8.1.5 Braking and shifting issues
If you find a problem with your brakes when doing your safety mechanical inspection, try adjusting their strokes by turning their tuning barrel. Make sure you lock it back screwing its lock nut.
If the problem persists, ask your authorized Devinci dealer for assistance.
If you find a shifting problem when doing your safety mechanical inspection, the derailleur is probably maladjusted. The problem may come from a simple elongation of your shifter cable.
Turn the shifters tuning barrel counterclockwise a quarter of a turn and lock it back with its lock nut. If the problem persists, ask your authorized Devinci dealer for assistance.
8.1.6 After riding 25 off-road hours or 50 road hours
Bring your bike to your authorized Devinci dealer for a complete check-up.
09
Carbon fi ber has been put to the test in recent years and has yielded excellent results. It has very different properties than aluminum. Unlike aluminum, carbon fi ber is not subject to fatigue,
does not deform, does not bend or dent: it breaks. Damaged carbon fi ber components may not appear compromised or dangerous but can be subject to sudden failure as result of impact,
and may do so without warning. DEVINCI would like you to enjoy safe rides. If you crash or your bicycle has sufered a major impact, have an authorized DEVINCI dealer inspect your bicycle.
WARNING : A damaged carbon fi ber frame may fail under impact and cause an accident leading to serious injury or even death. A crash or impact may result in damaged
carbon fiber. If you suspect damage to your carbon fi ber frame or components due to crash or impact, bring your bicycle immediately to an authorized DEVINCI
dealer for inspection. DO NOT CONTINUE TO RIDE!
10.1 Inspection
Inspect regularly your frame and components using your eyes, ears and hands. If you suspect an anormaly, cease riding immediately and bring it to an authorized DEVINCI dealer for
inspection.
10.1.1 Visual
Visually inspect your carbon fi ber frame and components. Checks for deep scratches, cracks, bumps or any other surface damage.
10.1.2 Touch
Be attentive to any change in perfomance or comfort during riding. Abnormal vibration, sudden loss of braking power or pedaling resistance can be signs of a problem.
10.1.3 Auditory
Be attentive to any abnormal noise. Cracking, grinding or any other abnormal noise may be indicative of a problem.
10.2 Maintenance
Carbon fiber requires more careful and frequent maintenance than other materials. Devinci recommands to:
Clean your carbon fi ber components after each use to remove any abrasive elements such as sand, small pebbles, tar or any other road contaminants;
Use a clean 100% cotton rag. Be sure that no abrasives stay stuck to the rag you are using to wipe the carbon fiber;
Use a mild non-abrasive detergent;
Do not use a high pressure water jet directly on your carbon fiber.
WARNING : Improper maintenance or negligence could lead to damage. A damaged carbon fiber component may fail under impact and cause an accident leading to serious
injury or even death. Improper maintenance could void your warranty.
vertical frame
Wheel clamp
support
rack
Nerver place a bicycle on a repair stand where the jaws clamp on the carbon fi ber frame or seat post. Doing so could permanently damage the carbon fi ber tubes. Substitute an aluminum
seat post or use our DEVINCI adaptor for aero seat post (MASA08001).
Aluminum seat
post clamp
DEVINCI adaptator
for aero seat post
If your bicycle travel case requires that you remove the wheels, it is imperative that you place spacers between the rear drop outs and the front fork drop outs to prevent misalignment of your
frame. Make sure that no loose items in your travel case come into direct contact with your carbon fi ber frame or components.
Fork spacer
10.3.4 Storage
The frames of cycles devinci inc,. 1555 Manic, Chicoutimi, Qubec, Canada (Devinci) are guaranteed against all manufacturing defects, for the periods specified below, as of the date of the
initial purchase. During there specific periods, Devinci will replace or repair without charge, and at its discretion, the Devinci frames that display a manufacturing defect. The parts replaced
or repaired in according with this warranty will be covered for a period equal to the remaining portion of the warranty of the original equipment. All frames are quaranteed for life. Paint and
decals placed under Devinci clear coat on all frame models : 1 year.
The pivot * for full susension frames : 1 year
The components assembled on Devinci frames are guaranteed by their respective manufacturers. Please contact your authorized Devinci retailer for more information regarding the
applicable warranty.
*The pivots include the bearings, bolts and axles holding together the elements of the suspension of the rear triangle.
WARRANTY EXCLUSIONS
Each Devinci bicycle was conceived for a specific use. The operational life of a bicycle varies according to its construction, maintenance and the care provided. Intensive use, use with a
heavy load, use during competitions or for activities other than those for which the bicycle was conceived decreases largely its operational life. Any of these conditions may lead to a random
failure. Abusive use will therefore cancel the warranty. Vinyl decals placed over the Devinci clear coat are not covered by warranty.