3 3 Agregacion de Enlace

1 - When a range of ports is being configured for EtherChannel, which mode will configure LACP so
that it initiates the EtherChannel negotiation?
desirable
auto
active
passive
2-
3 - What is an advantage of using LACP?
decreases the chance of a spanning-tree loop
provides a simulated environment for testing link aggregation
allows automatic formation of EtherChannel links
decreases the amount of configuration that is needed on a switch for EtherChannel
increases redundancy to Layer 3 devices
4 - Which command will initiate EtherChannel interface configuration mode?
interface port-channel interface-identifier
interface interface-identifier
interface range interface-identifier
channel-group group-identifier
5 - Launch PT Hide and Save PT

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
What are two reasons why the ping messages that are issued from Laptop0 towards Laptop1 are
failing? (Choose two.)
The wrong cable types are connecting the two switches.
The channel group mode is not set correctly on the switches.
The interface VLAN 1 is shut down on both switches.
The channel group should be configured as a trunk on each switch.
The two interfaces on each of the switches belong to different VLANs.
6 - Which three options must match in order to establish an EtherChannel between two directly
connected switches? (Choose three.)
speed of the interfaces that are used for EtherChannel
port numbers that are used for the EtherChannel
VLAN memberships of the interfaces that are used for EtherChannel
duplex settings of the interfaces that are used for EtherChannel
port security settings on the interfaces that used for EtherChannel
domain names on the switches
Refer to the exhibit. Which switching technology would allow each access layer switch link to be
aggregated to provide more bandwidth between each Layer 2 switch and the Layer 3 switch?
trunking
EtherChannel
HSRP
PortFast
8 -Which statement is true regarding the use of PAgP to create EtherChannels?
It requires more physical links than LACP does.
It mandates that an even number of ports (2, 4, 6, etc.) be used for aggregation.
It is Cisco proprietary.
It increases the number of ports that are participating in spanning tree.
It requires full duplex.
9 - Which PAgP mode combination will establish an EtherChannel?
switch 1 set to desirable; switch 2 set to desirable.
switch 1 set to on; switch 2 set to desirable.
switch 1 set to auto; switch 2 set to auto.
switch 1 set to auto; switch 2 set to on.
10 -What is a best practice to use before beginning an EtherChannel implementation?
Shut down each of the affected interfaces.
Assign affected interfaces to VLAN 1.
Assign affected interfaces to the management VLAN.
Enable each of the affected interfaces.
Assign affected interfaces to an unused VLAN.
11 - Which two protocols are link aggregation protocols? (Choose two.)
STP
802.3ad
EtherChannel
RSTP
PAgP
12
Refer to the exhibit. A network administrator has decided that an EtherChannel between ports 0/1 and
0/2 on switches S1 and S2 would help performance. After making the configuration, the administrator
notices no performance gain. Based on the output that is shown, what two possible assumptions could
a network administrator make? (Choose two.)
The EtherChannel bundle is working.
One of the ports on S2 was not configured correctly.
Switch S2 must be configured so that the maximum number of port channels is increased.
LACP and PAgP were both used to form the EtherChannel.
Switch S2 did not use a compatible EtherChannel mode.
The EtherChannel bundle is not working.
13
Which statement describes an EtherChannel implementation?
EtherChannel can connect up to a maximum of eight separate links.
EtherChannel operates only at Layer 2.
PAgP cannot be used in conjunction with EtherChannel.
A trunked port can be part of an EtherChannel bundle.
14
When a range of ports is being configured for EtherChannel by the use of PAgP, which mode will form
the bundled channel only if the port receives PAgP packets from another device?
active
desirable
auto
passive
15
As the network administrator you have been asked to implement EtherChannel on the corporate
network. What does this configuration consist of?
16
grouping multiple physical ports to increase bandwidth between two switches
grouping two devices to share a virtual IP address
providing redundant devices to allow traffic to flow in the event of device failure
providing redundant links that dynamically block or forward traffic
Refer to the exhibit. The administrator tried to create an EtherChannel between S1 and the other two
switches via the commands that are shown, but was unsuccessful. What is the problem?
Traffic cannot be sent to two different switches through the same EtherChannel link.
Traffic can only be sent to two different switches if EtherChannel is implemented on Gigabit
Ethernet interfaces.
Traffic can only be sent to two different switches if EtherChannel is implemented on Layer 3
switches.
Traffic cannot be sent to two different switches, but only to two different devices like an
EtherChannel-enabled server and a switch.
17
An EtherChannel link using LACP was formed between two switches, S1 and S2. While verifying the
configuration, which mode combination could be utilized on both switches?
S1-on and S2-active
S1-passive and S2-active
S1-passive and S2-passive
S1-on and S2-passive
18
What is the most cost-effective method of solving interface congestion that is caused by a high level of
traffic between two switches?
aggregate ports by using EtherChannel
insert a router between the switches
increase uplink speed
add more VLANs to reduce broadcast domains
19
Refer to the exhibit. An EtherChannel was configured between switches S1 and S2, but the interfaces
do not form an EtherChannel. What is the problem?
The interface port-channel number has to be different on each switch.
The switch ports were not configured with speed and duplex mode.
The EtherChannel was not configured with the same allowed range of VLANs on each
interface.
The switch ports have to be configured as access ports with each port having a VLAN
assigned.
20
Which two load balancing methods can be implemented with EtherChannel technology? (Choose two.)
destination IP to source IP
destination MAC to destination IP
source IP to destination IP
source MAC to destination MAC
destination IP to destination MAC
destination MAC to source MAC

3 3 Agregacion de Enlace

Uploaded by

Copyright:

Available Formats

3 3 Agregacion de Enlace

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

3 3 Agregacion de Enlace

Uploaded by

Copyright:

Available Formats

1 - When a range of ports is being configured for EtherChannel, which mode will configure LACP so

that it initiates the EtherChannel negotiation?

3 - What is an advantage of using LACP?

decreases the chance of a spanning-tree loop

provides a simulated environment for testing link aggregation

allows automatic formation of EtherChannel links

decreases the amount of configuration that is needed on a switch for EtherChannel

increases redundancy to Layer 3 devices

4 - Which command will initiate EtherChannel interface configuration mode?

interface port-channel interface-identifier

interface range interface-identifier

5 - Launch PT Hide and Save PT

The wrong cable types are connecting the two switches.

The channel group mode is not set correctly on the switches.

The interface VLAN 1 is shut down on both switches.

The channel group should be configured as a trunk on each switch.

The two interfaces on each of the switches belong to different VLANs.

speed of the interfaces that are used for EtherChannel

port numbers that are used for the EtherChannel

VLAN memberships of the interfaces that are used for EtherChannel

duplex settings of the interfaces that are used for EtherChannel

port security settings on the interfaces that used for EtherChannel

domain names on the switches

8 -Which statement is true regarding the use of PAgP to create EtherChannels?

It requires more physical links than LACP does.

It increases the number of ports that are participating in spanning tree.

It requires full duplex.

9 - Which PAgP mode combination will establish an EtherChannel?

switch 1 set to desirable; switch 2 set to desirable.

switch 1 set to on; switch 2 set to desirable.

switch 1 set to auto; switch 2 set to auto.

switch 1 set to auto; switch 2 set to on.

10 -What is a best practice to use before beginning an EtherChannel implementation?

Shut down each of the affected interfaces.

Assign affected interfaces to VLAN 1.

Assign affected interfaces to the management VLAN.

Enable each of the affected interfaces.

Assign affected interfaces to an unused VLAN.

11 - Which two protocols are link aggregation protocols? (Choose two.)

The EtherChannel bundle is working.

One of the ports on S2 was not configured correctly.

LACP and PAgP were both used to form the EtherChannel.

Switch S2 did not use a compatible EtherChannel mode.

The EtherChannel bundle is not working.

EtherChannel can connect up to a maximum of eight separate links.

EtherChannel operates only at Layer 2.

PAgP cannot be used in conjunction with EtherChannel.

A trunked port can be part of an EtherChannel bundle.

grouping multiple physical ports to increase bandwidth between two switches

grouping two devices to share a virtual IP address

providing redundant links that dynamically block or forward traffic

S1-on and S2-active

S1-passive and S2-active

S1-passive and S2-passive

S1-on and S2-passive

aggregate ports by using EtherChannel

insert a router between the switches

increase uplink speed

add more VLANs to reduce broadcast domains