Technical Data:: Oasis Epoxy TL 8758
Technical Data:: Oasis Epoxy TL 8758
Technical Data:: Oasis Epoxy TL 8758
PRODUCT :
Description
Oasis Epoxy TL8758 is Low VOC high build, high solids two pack epoxy
Phenolic primer/finish.
Recommended Use
It is used for internal coatings of storage tanks and vessel. It is suitable for
insulated steel surfaces including pipe work and the equipments.
Suitable to use up to 150C
753%
Flash Point
Base - 24C
V.O.C.
247gms/ltr
Colours
Pack Size
Mixing Ratio
:
:
:
6 m 2 /Ltr
5 m 2 /Ltr
3.75 m 2 /Ltr
125 m
150 m
200 m
166 m
200 m
267 m
Spreading rates are calculated and due allowance for loss and wastage should
be made.
:
:
:
15C
6Hrs
Additive 26 C
25C
24Hrs
35C
4 hrs
2hr
24Hrs
24Hrs
These figures are given as a guide only. Factors such as air movement and
humidity must also be considered.
Cleanser or Thinner
Pot Life
Thinner # 5
15C
3 hours
23C
2hours
35C
1.5 hours
Application Notes
Application Methods
Surface Preparation
SAFETY, HEALTH & ENVIRONMENTAL INFORMATION (READ THIS SECTION BEFORE USE)
SOLVENT BASED PAINT PRODUCT
W hen applying paint it is advisable to wear suitable eye protection. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
Remove splashes from skin : use soap and water or a recognised skin cleaner.
Keep container tightly closed and keep out of reach of children. Do not use or store by hanging on a hook. Do not empty into wadis, drains or watercourses.
August 2013
Issue 1: Revision:0
For further information please contact
AL GURG PAINTS L.L.C
Head Office & Factory P.O. Box 22334,
Sharjah, U.A.E
Tel : (+971)6-5343919 Fax : (+971)6 343983
E-mail : enquiries@agp.ae
Web : www.aglpuae.com
APPLICATION DATA
PRODUCT :
SURFACE PREPARATION
For better performance we recommend blast clean to Sa 2.5 BS 7079: Part A1: 1989 (ISO 8501-1: 1988). Average surface profile should be in the
range 50-75. Manually prepared surfaces should be to a minimum standard of St 3 BS 7079: Part A1: 1989 at the time of coating.
Ensure surfaces to be coated are dry and free from all traces of surface contaminants.
APPLICATION EQUIPMENT
Airless Spray
Nozzle Size
Fan Angle
Operating Pressure
The airless spray details given above are intended as a guide only. Fluid hose length and diameter, paint temperature and project complexity all
have an effect on the choice of spray tip and operating pressure. The operating pressure should be the lowest possible consistent with satisfactory
atomisation. As conditions vary, it is the applicators' responsibility to ensure that the equipment in use has been adjusted to give optimum
performance. In case of any difficulties or queries, please contact Al Gurg Paints L.L.C.
Conventional Spray
Nozzle Size
Atomising Pressure
Fluid Pressure
1.50mm 2.0mm
2.8kg/cm 3.5kg/ cm
0.4kg/cm (6 psi)
The conventional spray details given above are intended as a guide only. It may be found that in some circumstances, slight variations in atomising
pressure, fluid pressure and alteration of tip arrangements may provide optimum atomisation. For application by conventional spray, thinning with up
to 10% Thinner No. 5 may be required. Adjustment for wet film thickness should be allowed. Thinning will affect VOC compliance.
ADDITIONAL NOTES
Drying, curing times should be considered as a guide only. For spraying maximum 5 to 10% dilution is recommended,
August 2013
Issue 1: Revision:0
For further information please contact
AL GURG PAINTS L.L.C
Head Office & Factory P.O. Box 22334,
Sharjah, U.A.E
Tel : (+971)6-5343919 Fax : (+971)6 343983
E-mail : enquiries@agp.ae
Web : www.aglpuae.com