Introduction To Impulse Hammers
Introduction To Impulse Hammers
Introduction To Impulse Hammers
Introduction
A transfer function of a mechanical system describes its dynamic behavior in
response to an applied stimulus (excitation). There are six major transfer functions used in mechanical systems analysis.
These are:
Dynamic Mass (Force/Acceleration)
Mechanical Impedance (Force/Velocity)
Dynamic Stiffness (Force/Displacement)
Compliance (Displacement/Force)
Accelerance (Acceleration/Force)
(Note that each of these transfer functions is itself a function of Force.)
Each transfer function describes the dynamic behavior of the mechanical system in a different fashion and each involves the ratioing of the output
response to the input stimulus. Response can be measured most conveniently
with accelerometers placed at important points throughout the structure under
test. Spectrum analyzers perform the necessary mathematical ratioing on input
and response signals to produce, almost instantaneously the desired transfer
function.
The input stimulus (forcing function) may be applied to the structure by various methods. One common way to excite structures is by use of an electrodynamic or hydraulic shaker. A force sensor attached to the armature driving the
test object may be used to define input force amplitude and a signal generator
controls frequency. When the test object is too large to be excited in this fashion, or when it is physically impossible to do so, there is another method to
consider.
An alternative method available to excite a structure without the complication
and expense of a shaker system, involves striking it with a calibrated dynamic
impulse hammer. A force sensor mounted in the head of the hammer transforms the input force pulse into an analogous waveform that contains the necessary amplitude and phase information to completely describe the forcing
function. Impact tip material stiffness helps determine the frequency content of
the input forcing function by controlling the impact pulse duration. By defining the frequency and amplitude of the forcing function, impulse hammers
present a fast, simple way to excite structures in a well defined fashion.
Spectrum analyzers in conjunction with hammer systems (with accelerometers) can instantaneously plot transfer functions greatly simplifying testing and
saving valuable man hours. A branch of mechanical system analysis called
Modal Analysis, uses software to further refine the frequency response data to
describe in detail each mode (resonance and anti-resonance) of the structure.
Dytran Dynapulse impulse hammers utilize an exclusive acceleration compensated quartz force sensor to ensure that hammer self-resonances do not produce spurious noise glitches in the hammer output signal spectrum. The
high rigidity of the force sensor combined with acceleration compensation produces a clean, smooth output signal which is an exact representation of the
forcing function, both in amplitude and phase.
The Low Impedance Voltage Mode (LIVM) force sensor is permanently mounted
to the front surface of the hammer head with electrical connections conveniently routed through head and handle, terminating in a BNC connector
located at the end of the handle. This streamlined concept in design was pioneered by Dytran and has become the industry standard.
21592 Marilla Street, Chatsworth, California 91311 Phone: 818.700.7818 Fax: 818.700.7880
www.dytran.com For permission to reprint this content, please contact info@dytran.com
Figure 2 is a typical result from a Dytran series 5800B hammer as seen with a
spectrum analyzer.
Figure 5 is an expanded view of the analog voltage pulse (time base) produced
by a 5801B using a hard plastic impact tip and no head extender. The pulse
duration is .640 mSec.
To decrease the high frequency content of the input excitation, increase head
inertia by adding a head extender and use a softer impact tip to increase the
rise time and pulse duration. This will further lower the frequency content of
the excitation.
Figure 6 is an expanded view of the pulse with added mass by use of a head
extender with the same impact tip as in Figure 5, above. Notice that the pulse
duration is longer.
Coherence plots will enable the user to determine if the structure is being properly excited at all frequencies of interest. Various Impact tip materials and
extender mass can be substituted to achieve close to optimum excitation.
System Interconnection
Figure 7 illustrates how an impulse hammer system may be used in conjunction with a spectrum analyzer. A computer operating in concert with the analyzer may be added to perform modal analysis, a software based extension of
mechanical system frequency response testing.
21592 Marilla Street, Chatsworth, California 91311 Phone: 818.700.7818 Fax: 818.700.7880
www.dytran.com For permission to reprint this content, please contact info@dytran.com
Hammer Selection
All Dytran hammers feature internal impedance converting IC amplifiers for
convenient LIVM operation. Hammers may be purchased separately or as hammer kits which include accelerometers, power supplies, cables, several tips and
head extenders. The complete Dytran hammer line consists of seven different
hammer configurations, from the very miniature 5800SL to the large 12 lb.
sledge hammer model 5803A, to excite a wide range of test objects and structures from tiny turbine blades to viaducts. All Dytran hammers come supplied
with NIST traceable calibration certificates at no extra cost.
The following summary will help in determining the best hammer for your
application:
Model 5800SL: This miniature Super Light hammer was designed to excite
very light compliant structures such as small turbine blades and disc drive read
heads. Model 5800SL has a very high tip stiffness and low head mass making it
ideal for very high frequency excitation of small structures. A removable head
extender is supplied with each instrument. The impact tip, made from hardened steel, is not interchangeable. Sensitivity is 100 mV/lbf.
Model Series 5800B: The first in the Dynapulse series, model 5800B has a 100
gram head mass and is available in five force ranges from 10 to 1,000 lbf. full
scale. Interchangeable impact tips and a 40 gram head extender are supplied.
Acceleration compensation ensures a smooth frequency spectrum free from
anomalies. This hammer is recommended for general purpose use on bearing
housings, brake rotors, I-beams, plates and other small structures and
machines.
Model Series 5801B: This general purpose Dynapulse hammer series is available in three force ranges, 500, 1000 and 5,000 lbf. Series 5801B hammers have
a 150 gram head which can be increased to 210 grams and 270 grams with the
two head extenders available. This hammer is recommended for engine block
castings, auto frames, airframes, machine tools, etc.
Model 5850B: The patented Dynapulse Multi-Range hammer offers versatility to dynamics laboratories where structures of varying size and weight are to
be tested. A three-position toggle switch located in the handle allows the user to
select sensitivities of 1, 10 and 100 mV/lbf. The switch summons three different
ranging capacitors to change sensitivity and adds no electrical gain to the circuit ensuring that the three ranges share the same low noise level. The model
5850B effectively replaces three dedicated range hammers. Dynapulse acceleration ensures smooth glitch free response. This hammer comes with three
impact tips and two head extenders to allow tailoring of the impulse. The very
wide dynamic range of this hammer provides adequate excitation of a multitude of structures from small to large.
Model 5802A: This lighter sledge hammer (3 lb head) can be equipped with
any one of four interchangeable plastic impact tips of varying stiffness and can
be used to excite low frequencies in concrete castings, storage tanks, pipelines,
towers, etc.
Model 5803A: Our heaviest hammer at 12 lbs, this instrumented sledge hammer has been used to shake buildings, bridges, dams and foundations.
Model 5805A: This is the lightest of the sledge hammers at 1 lb and was
designed to be used on smaller structures than the 3 lb 5802A.
21592 Marilla Street, Chatsworth, California 91311 Phone: 818.700.7818 Fax: 818.700.7880
www.dytran.com For permission to reprint this content, please contact info@dytran.com