Yokogawa

GS 01R4B04-00E-E
PRINCIPLE OF MEASUREMENT
Mass fow measurement according to the Coriolis principle.
Almost all fuids including multi phase fuids, high viscosity
liquids (pastes and slurries)
and liquid with a certain
content of gas. For difficult
fuids (e.g. abrasive or
highly corrosive fuids) and
gases please contact
your Yokogawa
representative.
3 Series
Coriolis Mass Flow and Density Meter
GS 01R04B04-00E-E
Copyright July 2003 (R)
14th edition, August 2012 (R)
Rota Yokogawa GmbH & Co. KG
Rheinstr. 8
D-79664 Wehr
Germany
General
Specifcations
RCCT39/XR RCCT34 - 39/IR RCCF31 + RCCS30LR - 33 RCCR31
RCCS34 - 39/IR
ROTAMASS is the integral and remote type Coriolis Mass
Flowmeter. Both types have highly refned digital signal
processing electronics, so that accurate and stable mass
fow measurement is achieved.
ROTAMASS employs a fame-proof type converter case
suitable for use in the hazardous area together with its
intrinsically safety type detector.
ROTAMASSs signal processing, housing protection and its
detectors special decoupling system against external loads and
vibrations, realize high performance in real applications.
FEATURES
Field transmitter type mass fowmeter for nearly all
fuids, including high viscosity liquids, slurries and multi
phase media
Field-mount and rack-mount remote converter available
Refned digital signal processing enables accurate and
stable measurement
A special detector decoupling system makes the device
highly independent from external loads or vibrations.
Simple fow path means self-draining, food capable and
simple to clean
High accuracy and high stability over a wide range
Accurate density measurement, up to +/- 0.0005 g/cm
Concentration measurement for solutions, suspensions
and emulsions (e.g. water cut, net oil computing)
Volume fow with reference density
Two analog outputs, 2 pulse outputs or status-out and
one status-in as standard I/O
Available in explosion proof versions (ATEX, FM, IECEx,
GOST/RTN, INMETRO, NEPSI, KOSHA)
European MID approval for Custody Transfer Measurement
acc. OIML R-117-1 (see GS 01R04B07-00E-E)
FMEDA report on request, SIL 2; SIL 3 levels can be
achieved if redundant meters are used
Wide temperature range 200C to 350C
Microprocessor-based multifunction capability
EEPROM protects parameter settings and totalized
values during power failure of any duration
High visibly LCD display
HART
communication function
Optional Foundation Fieldbus communication
(see GS 01R04B05-00E-E)
Optional MODBUS
communication
Optional intrinsically safe outputs
Choice of tube materials
EN, ASME or JIS fanges as standard, others on request
GS 01R04B04-00E-E
Contents
Features Page 1
Principle of measurement Page 1
Performance specifcations Page 2
Normal operating conditions Page 3
Mechanical specifcations Page 5
Remote cable specifcation Page 5
Electrical specifcations Page 6
Hazardous area specifcations Page 7
Planning and installation hints Page 11
Dimensions Page 14
Model-, suffix- and option- codes Page 22
GS 01R04B04-00E-E 14th edition August 09, 2012-00
2
All Rights Reserved. Copyright 2003, Rota Yokogawa
Qnom is the water fow rate at about 1 bar pressure drop.
The fowmeter has a default low cut of 0.05% of Qnom.
Accuracy mass fow (refer to table 2):
Liquid RCCS30LR:
0.15% of fow rate zero stability / fow rate *100%
Liquid RCCS30 - 39/XR:
Gas (option /GA):
Accuracy volume fow :
SQRT ( (mass fow error in %) + (density error in %))
Please refer to the Yokogawa sizing software.
Accuracy based on the frequency output includes the combined
effects of repeatability, linearity and hysteresis.
Repeatability for liquids:
0.05% (zero stability/2) / fow rate *100%
Table 2 : Zero stability
Type
RCCS30
LR
RCCS30 RCCS31 RCCS32 RCCS33
kg/h 0.003 0.005 0.0085 0.019 0.048
Type RCCx34 RCCx36 RCCx38 RCCx39
RCCx39
/IR
RCCx39
/XR
kg/h 0.15 0.5 1.6 5 13 25
PERFORMANCE SPECIFICATIONS
Model
- Remote detector RCCS30LR to 33: 2 tubes, low fow design
- Remote detector RCCS34 to 39/XR : 2 tube design
- Remote feld-mount converter RCCF31
- Remote rack-mount converter RCCR31
- Integral type RCCT34 to 39/XR: 2 tube integral design
Fluid to be measured : Liquid, gas or slurries
Measurement Items : Mass fow, density, temperature
and derived from these values:
concentration, volume fow and
net fow
Mass Flow Measurement
Table 1: measuring range
Type
RCCS30
LR
Qmax t/h 0.04 0.1 0.3 0.6 1.5
Qnom t/h 0.021 0.045 0.17 0.37 0.95
RCCx39
/IR
RCCx39
/XR
Qmax t/h 5 17 50 170 300 600
Qnom t/h 3 10 32 100 250 500
Pressure Dependency
The stiffness of the ROTAMASS tubes is slightly line pressure
dependent. The static pressure effect of mass fow and density
can be corrected by setting the static pressure manually via menu.
Table 3 : Static pressure effect on mass fow (if not corrected)
Type
RCCS30
LR
% of
rate
per bar
SH ---- ---- ---- ---- ----
HC 0.00000 0.00000 0.00012 0.00246 0.0035
RCCx39
/IR
% of
rate
per bar
SS 0.00081 0.00346 0.00950 0.01058 0.02920
HC 0.00084 0.00336 0.00896 0.00808 0.01780
Type
RCCx39
/XR
% of
rate per
bar
SS 0.00740
HC ----
Density Measurement
Adjustment with water and air at calibration temperature.
Measuring range:
RCCS30LR - 38: 0.3 kg/l to 5 kg/l
RCCx39 -39/XR : 0.3 kg/l to 2 kg/l
No density measurement for gas application.
With option /K4 thermal stabilized.
For option /K6 see also Special calibrations on page 3.
Table 4: Accuracy (at calibration conditions):
Type Standard Option /K4 Option /K6
RCCS30LR 0.02 g/cm *) ------ ------
RCCS30 0.008 g/cm *) ------ ------
RCCS31 0.004 g/cm 0.001 g/cm ------
RCCS32 0.004 g/cm 0.001 g/cm 0.0005 g/cm
RCCS33 0.004 g/cm 0.001 g/cm 0.0005 g/cm
RCCx34 0.003 g/cm 0.001 g/cm 0.0005 g/cm
RCCx36 0.0022 g/cm 0.001 g/cm 0.0005 g/cm
RCCx38 0.0015 g/cm 0.001 g/cm 0.0005 g/cm
RCCx39 0.0015 g/cm 0.001 g/cm 0.0005 g/cm
RCCx39//IR 0.0015 g/cm ------ ------
RCCx39//XR 0.0015 g/cm ------ ------
*) 0.003 g/cm on request
Repeatability:
RCCS32-33, RCCx34-39/XR : 0.0005 g/cm (Std, /K4)
Static pressure effect:
Compensated if static pressure is set in the menu
Specifcation of high performance density measurement
option /K6: Density calibration
Density range : 0.3 to 2.5 kg/l
Ambient temp. range : -10C to 50C
Fluid temp. range : -50C to 150C (not /HT)
150C to 350C (/HT)
Minimum fow rate for specifed accuracy:
- RCCx36 to RCCx39 : 700 kg/h
- RCCx34 : 140 kg/h
- RCCS33 : 90 kg/h
- RCCS32 : 37 kg/h
Maximum fow rate : Qnom
Repeatability : 0.0002 g/cm
Temperature measurement:
(0.5C+0.002*abs(T
medium
-20C)) (not /HT)
(0.5C+0.008*abs(T
medium
-20C)) (/HT)
Density accuracy : for one phase liquids only
Process temperature infuence :
0.000015 g/cm * abs(Tfuid-20C)
-1.0
-0.9
-0.8
-0.7
-0.6
-0.5
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0 50 100 150
Flow in % of Qnom
E
r
r
o
r

i
n

%
F10.EPS
3
Temperature Measurement
Temperature measuring range of converter :
Standard, /LT, /MT : -200C to 230C
Option /HT : 0C to 350C
Accuracy:
Standard (-70C to 150C) : (0.5C+0.005*abs(T
medium
-20C))
Option /MT (-70C to 230C) : (0.5C+0.005*abs(T
medium
-20C))
Option /LT (-200C to 150C): (1.0C+0.008*abs(T
medium
-20C))
Option /HT (0C to 350C) : (1.0C+0.008*abs(T
medium
-20C))
For process temperatures more than 80C higher/lower than
ambient temperature the detector should be insulated to
maintain optimum accuracy.
Heat Tracing
Heating with heat carrier, insulation and protection housing.
The max. surface temperature at the protection housing from
inner heating is 40C. Above 150C process temperature
insulation from the manufacturer is recommended. However
up to 230C process temperature the customer can insulate
the detector themselves.
Option /T1 : only insulation and protection
Option /T2 : insulation, protection and heating line
Option /T3 : like /T2 but with ventilation
Process connection for the heat carrier fuid (see table 10):
for D-type fanges : EN DN 15 PN 40 Form B1
for A-type fanges : ANSI - 150 lbs.
for J-type fanges : JIS DN15 10K
Max. pressure : PN 40
Protection class : IP54, install roof protected
For fuid temperatures below -70C select option /LT and ask
for special insulation (see also page 10).
Calibration for liquids and gases :
The ROTAMASS fowmeters are always factory calibrated
with water. Calibration Conditions:
- Water : 22.5C 12.5C
- Ambient temperature : 22.5C 12.5C
- Process Pressure : 1 to 2 bar abs
- Installation: RCCS30LR to RCCS/T38 vertical
RCCS/T39 to RCCS/T39/XR horizontal
All specifcations are based on above mentioned calibration
reference conditions, a fow calibration protocol is attached to
each instrument.
Special calibrations
- Mass-/Volume fow calibration with factory certifcate (option /K2):
Calibration with water at customer specifed fow values
according calibration order sheet.
- Mass-/Volume fow calibration with DKD/DAkkS certifcate
EN17025 (option /K5):
Calibration with water at customer specifed fow values
according calibration order sheet.
- Density calibration with factory certifcate (option /K6):
Adjustment and check with 3 different fuids, fuid temperature
infuence adjustment for low ambient temperature infuence
and thermal treatment for long term density measurement
stability, enhanced temperature measurement (see also
page 11).
Dual Seal approval (option /DS):
- Conform with ANSI/ISA-12.27.01.
- Only for use with hazardous substances.
- Up to ANSI class 900 line pressure.
- Only with FM approval option.
- For liquid application the leakage detection is realized by
software in the converter.
- For gas application options /GA and /RD (rupture disk) are
mandatory.
- Rupture disk is only for annunciation.
NORMAL OPERATING CONDITIONS
Ambient Temperature Limits
- Remote detector RCCS3 :
Standard : -50C to +80C
Option /LT : -50C to +80C
Option /MT : -50C to +80C
Option /HT : -50C to +65C
(up to 280C medium temperature)
-50C to +55C
(up to 350C medium temperature)
Terminal box temperature should not exceed 100C
- Remote converter RCCF31, RCCR31 and Integral type
RCCT3:
Display operating range : -20C to +55C)
Electronic operating range : -40C to +55C
Cold start : above -30C
Where meters are mounted in direct sunlight, it is recom-
mended to install a sunshade. This is particularly important in
countries with high ambient temperatures.
Ambient Humidity Limits : 0 to 95% RH
Process Temperature Limits
Detector :
- RCCS30LR to 33 : -50C to 150C
- RCCS34 to 39/XR : -70C to 150C
- RCCS34 to 39/XR /MT : -70C to 230C
(Range 150C - 230C
recommended with /Tx option)
- RCCS34 to 39/XR /LT : -200C to 150C
- RCCS34 to 39/IR /HT : 0C to 350C (only with /Tx option
or with /S2 and customer insulation)
Integral type :
- RCCT34 to 39/XR : -50C to 150C
For use in hazardous area see Hazardous Area Specifcations
Heat Carrier Fluid Temperature Limits
(Option /T2 or /T3 only for remote type RCCS30LR to 39/IR)
- Standard : 0C to 150C
- With option /LT : -200C to 150C
- With option /MT : 0C to 230C
- With option /HT : 0C to 350C
For fuid temperatures below -70C select option /LT and ask
for special insulation (see also page 10).
Process Pressure Limit
According to the fange ratings:
- EN PN 16 : max. 16 bar
- EN PN 100 : max. 100 bar
- ASME class 150 : max. 16 bar
- JIS 10K : max. 14 bar (1.4 MPa)
- JIS 20K : max. 34 bar (3.4 MPa)
The RCCS30LR to RCCS34 have also thread connection. For
these connections the max. allowed tube pressure is the
limitation. For all other standard process connection please
fnd the max. process pressure in table 9.
4
On request following maximum pressure for SL/SH up to 27C
(RT=Room Temp.):
- RCCS30LR : 400 bar
- RCCS30 : 400 bar
- RCCS31 : 350 bar
- RCCS32 : 285 bar
- RCCS33 : 285 bar
- RCCS34 / RCCT34 : 260 bar
- RCCS39/IR / RCCT39/IR : 110 bar
- RCCS39/XR / RCCT39/XR : 95 bar
For higher medium temperatures maximum tube pressure
needs to be derated as follows :
up to 50C : 4% derating
51 to 100C : 11% derating
Higher pressure on request.
The maximum process pressure of a single instrument is given
by the lower value either of the process connections (table 9)
or tubes. The maximum temperature and process pressure
limits of an instrument are marked on the name plate as TS
and PS.
The given temperature/pressure ranges are calculated and
approved without corrosion or erosion effects. The customer
is fully responsible to select proper materials to withstand his
corrosive or erosive conditions. In case of heavy corrosion
and/or erosion the instrument may not withstand the pressure
and an incident may happen with human and/or environmental
harm. Yokogawa will not take any liability regarding damage
caused by corrosion / erosion. If corrosion/erosion may happen,
the user has to check periodically if the necessary wall thick-
ness is still in place.
Gas Content Limits for Liquid/Gas Mixtures
Gas content limit is defned as the amount of gas in a liquid/
gas mixture which generates an error in the converter. The
gas content limit is dependent on viscosity,
surface tension and bubble size of the liquid/gas mixture.
Furthermore it is highly fow rate dependent (the higher the
fow rate, the lower the gas content limits). The stated values
are for a fow of 50% of Qnom and water/air without /HP:
Model Gas fraction
- RCCS30LR to RCCS32 : no limitation
- RCCS33 non-Ex type : no limitation
- RCCS33 Ex type : approx. 35%
- RCCx34 : no limitation
- RCCx36 : approx. 50%
- RCCx39/IR : approx. 3%
- RCCx39/XR (with /HP) : approx. 2%
With option /HP the gas content limits are improved.
With liquid/gas mixtures the specifed mass fow accuracy will
not be achieved.
For short time aeration a function can be activated to keep
the current outputs constant during the aeration time.
Other 2 Phase Flow, liquid/solid and liquid/liquid
Two phase fow can generate minus span errors. The errors
are proportional to the difference in density between the 2
phases and the amount of the second phase. If the particles
or droplets are very small no errors will be generated.
Secondary Containment
Model Typical rupture
pressure
Option /J1
pressure test *)
RCCS30LR-33 65 bar ---
RCCx34-36 120bar 60 bar
RCCx38 120 bar 40 bar
RCCx39-39/IR 80 bar 10 bar
RCCx39/XR on request ---
RCCx39/XR/HT 50 bar ---
*) Pressure test with safety factor S=1.1
However if the detector housing is exposed to this pressure
it will deform and measurement will be strongly infuenced.
Therefore the pressure test of the housing (option /J1) can
only be done as shown in above table.
Power Supply and Power Consumption
- AC-/DC-type : For details see Electrical Specifcations
5
REMOTE CABLE RCCY03 SPECIFICATION
Li2Y(St)/CY 3x2 AWG24 + 1x3 AWG20
pair/triple shielded; pair/triple twisted; overall shielding
RCCY033/034 and RCCY031/032/KS1: fame propagation acc. IEC 60332-1.
Table 6 : Cable specifcations
Model code Temperature
range
Wire gauge Resistance of
loop
Capacitance
wire/wire
Capacitance
wire/shield
Inductance
wire/wire
RCCY031/032 -50 to +70C
AWG 24
AWG 20
190 /km
70 /km
157 nF/km
193 nF/km
249 nF/km
290 nF/km
0.60 mH/km
0.65 mH/km
RCCY031/032 /KS1 -50 to +70C
AWG 24
AWG 20
190 /km
70 /km
157 nF/km
193 nF/km
249 nF/km
290 nF/km
0.60 mH/km
0.65 mH/km
RCCY033/034 -30 to +105C
AWG 24
AWG 20
177 /km
70 /km
175 nF/km
145 nF/km
350 nF/km
290 nF/km
0.80 mH/km
0.70 mH/km
RCCY033/034 /KS1 -30 to +105C
AWG 24
AWG 20
177 /km
70 /km
175 nF/km
145 nF/km
350 nF/km
290 nF/km
0.80 mH/km
0.70 mH/km
MECHANICAL SPECIFICATIONS
Protection Class
- RCCT3x : IP66/67
- RCCF31 : IP66/67
- RCCS3x : IP66/67
- RCCR31 : IP20
Materials
- Detector housing : Stainless steel 304/1.4301
- Detector terminal box : 316L/1.4404
- Detector gas flling plug: 1.4305
- Detector insulation housing
: Stainless steel 304/1.4301
- Detector rupture disk (/RD)
: 316L
- Field- mount converter housing
: Aluminium alloy with Polyurethane
corrosion-resistant coating or
epoxy coating (option /X1)
- Field- mount converter mounting bracket:
: Stainless steel 304/1.4301
- Rack- mount converter housing
: Aluminium

Coating Color
- Field-mount converter case
: Mint green
Wetted Parts
- RCCS30LR to 33 :
Measuring tubes : Ni-Alloy C-22/2.4602
Process connections : 316L/1.4404
- RCCx34 to 39/IR :
Measuring tubes and process connection
: 316L/1.4404/1.4435 or
Measuring tubes and fange face
: Ni-Alloy C-22/2.4602
- RCCx39/XR :
Measuring tubes and process connection
: 316L/1.4404/1.4435
Table 5 : Diameter of measuring tubes
Type
RCCS30
LR
Inner
diameter
mm 0.9 1.2 2.1 3 4.5
Wall thick-
ness
mm 0.15 0.2 0.25 0.25 0.4
RCCx39
/IR
RCCx39
/XR
Inner
diameter
mm 7.7 13.4 22.1 37.2 54.5 82.50
Wall thick-
ness
mm 0.89 1.24 1.65 2.6 2.9 3.2
Pressure Equipment Directive 97/23/EC
RCCS30LR- RCCS33 : SEP
FLUID GROUP 1 : MODULE H, CATEGORY III
FLUID GROUP 2 : RCCX34-RCCX38: SEP
: RCCX39-RCCS39/XR: CAT.I
For all Process Connections
: CRN 0F12074.5
Vibration Test : Acc. IEC 60068-2-64
6
ELECTRICAL SPECIFICATIONS
Power Supply
- AC- type : 90 V to 264 V AC
- AC- Ex-type : 90 V to 250 V AC
- DC- type : 20.5 V to 28.8 V DC
Power consumption : max. 25 VA / 10 W
External circuit breaker rating : 5 A, 250 V (In the converter
no power switch is installed).
Fuse on Base Board
- AC- type : 2 A, T, breaking capacity 1500A
- DC- type : 2 A, T, breaking capacity 1500A
I/O Signals
- Two active current outputs: Iout1, Iout2
4 to 20 mA DC, galvanic separated from other signals,
Load resistance : 20 to 600
Failure current according NAMUR NE43
Ambient temperature effect : < 0.05% of span/10C
Linearity : 0.008 mA = 0.05% of span
Setting range URV for liquids: 5 to 100% of Qnom
Setting range URV for gases: 1 to 100% of Qnom
- Two pulse outputs / status outputs : Pout, Sout
Passive transistor contact output, 30 V DC, 200 mA
Output rate
Output 1 : 0 to 10000 pulses/s
Output 2 : 0 to 2000 pulses/s
Option /NM : passive, according EN 60947-5-6
Option /AP : active output, 12 V, 6 mA, R
L
> 10 k
Active pulse output is not isolated from current output 2
As frequency output
Output 1 : 20 Hz to 10000 Hz
Output 2 : 20 Hz to 2000 Hz
- Status input : Voltage-free contact
Closed : < 200
Open : > 100 k
Option /KF2, /EF2, /UF2: 2 intrinsic safe outputs
- One passive current output (additional power supply
needed) : Iout
4 to 20 mA DC, galvanic separated from other signals.
Supply voltage 10.5 V to 30 V DC (without HART
), 165 mA
Supply voltage 16.75 V to 30 V DC (with HART
), 165 mA
Load resistance : 20 ... 600
Ambient temperature effect : < 0.05% of span/10C
- One pulse output / status output : Pout
Passive transistor contact output, 30 V DC, 100 mA
Output rate : 0 to 2000 pulses/s
As frequency output : 20 Hz to 2000 Hz
Option /NM : passive, according EN 60947-5-6
- No status input
Digital Communication
- HART
communication protocol rev. 5, superimposed on

4 -20 mA DC signal (Iout1)
- Load resistance : 230 to 600 (including cable)
- Power line spacing : >15 cm, avoid parallel wiring
- Cable length : 2 km if CEV cables are used
- FOUNDATION Fieldbus communication (/FB)
- see GS 01R04B05-00E
- MODBUS
communication (/MB1)
- Physical interface RS485 as two wire data bus according
EIA/TIA-485
- Maximal bus length is depending from bus topology and
communication speed.
- Addresses: 1 to 247
- Baud rates: 1200, 2400, 4800, 9600, 19200, 38400,
57600, 76800, 115200
- Data formats: E/1, O/1, N/1, N/2 (parity/stop bits)
- Modes: RTU, ASCII
Setting Functions
Parameter setting is possible by using the infrared switches
on the display or with HART
communication. For comfortable

setting we recommend to use Yokogawas Filedmate setting
tool (DTM based).
Display Function
- Up to 4 lines.
- 4 languages selectable (English, German, French, Russian)

Damping Functions
Adjustable from 0 seconds to 200 seconds, controls display
and outputs.
Isolation Resistance of Converter
When surge arrestors are removed
- between power and ground terminal: >100 M / 500 V DC
- between power and I/O terminals : >20 M / 100 V DC
- between I/O terminals and ground : >20 M / 100 V DC
Dielectric Strength
When surge arrestors are removed
- between power and ground terminal : 1,500 V AC for 1 minute
Lightning Protection
Arresters 2000 A are inside of the converter for power
supply lines.
Electromagnetic Compatibility
Acc. EN 61326-1: 2006, Class A, Table 2
EN 61326-2-3: 2006
EN 61000-3-2: 2006
EN 61000-3-3: 2008
Safety Requirement Standards
Acc. EN 60010-1: 2001
Overvoltage category II
Pollution degree 2
7
HAZARDOUS AREA SPECIFICATIONS
ATEX
Remote Detector RCCS30LR ... 39/XR (Option /KS1):
- KEMA 01ATEX 1075 X
- Intrinsically safe
- II 2G Ex ib IIB/IIC T1 ... T6
- II 2D Ex ibD 21 IP6x Txxx (xxx = max. surface
temperature see below)
- Max. surface temperature :
Standard : 150C
/MT : 220C
/HT : 350C
- Degree of protection : IP67
- Ambient humidity : 0 to 95% RH
- Ambient temperature range
Standard and option /MT
: -50C to +80C
Option /HT (process temperature < 280C
: -50C to +65C
: -50C to +55C
- Process temperature limits :
Standard : -50C to 150C
Option /MT: : -50C to 220C
- Heat carrier fuid temperature limits
Remote Converter RCCF31 (Option /KF1) :
- Flame proof with intrinsic safe connection to detector (ib)
- II 2G Ex d(e) [ib] IIC T6
- II 2G Ex d(e) [ib] IIB T6 with option /HP
- II 2D Ex tD [ibD] A21 IP6x T75C
- Max. surface temperature : 75C
- Power supply : 90 to 250 V AC, 50/60 Hz or
20.5 to 28.8 V DC
- Power consumption : max. 25 VA / 10 W
- Ambient temperature range : -40C to +55C
Remote Converter RCCF31 (Option /KF2) :
- Additional intrinsic safe outputs.
- II 2G Ex d(e) [ia] [ib] IIC T6
- II 2G Ex d(e) [ia] [ib] IIB T6 with option /HP
Protection [ia] refers to the intrinsic safe outputs.
Protection [ib] refers to the connection to the detector.
20.5 to 28.8 V DC
- Power consumption : max. 25VA / 10W
Remote Converter RCCR31 (Option /KS1) :
- Associated apparatus with intrinsic safe connection to
detector (ib)
- II (2)G [Ex ib] IIC
- II (2)G [Ex ib] IIB with option /HP
- II (2)D [Ex ibD]
20.5 to 28.8 V DC
WARNING

Remote rack-mount converter RCCR31 must be installed in
safe area !
Integral Type RCCT34 ... 39/XR (Option /KF1) :
- II 2G Ex d(e) [ib] IIC T6 ... T3
- II 2G Ex d(e) [ib] IIB T6 ... T3 with option /HP
- II 2D Ex tD A21 IP6x T150C
- Power supply : 90 to 250V AC, 50/60 Hz or
20.5 to 28.8 V DC
- Power consumption : max. 25V A / 10 W
Integral Type RCCT34 ... 39/XR (option /KF2) :
- KEMA 02ATEX 2183 O
- II 2G Ex d(e) [ia] [ib] IIC T6 ... T3
- II 2G Ex d(e) [ia] [ib] IIB T6 ... T3 with option /HP
- Power supply : 90 to 250V AC, 50/60 Hz or
20.5 to 28.8V DC
Electrical Data Remote Detector RCCS30LR ... 33 :
- Driving circuit : terminals D+ and D
Ex ib IIC : Ui = 16 V; Ii = 53 mA; Pi = 0.212 W
Li = 4.2 mH; Ci = negligible small
Ex ib IIB : Ui = 16 V; Ii = 153 mA; Pi = 0.612 W
- Sensor circuits: terminals S1+ and S1- or S2+ and S2-
- Temperature sensor circuit : terminals TP1, TP2, TP3
Li = negligible small; Ci = negligible small
Electrical Data Remote Detector RCCS34 ... 39/XR :
Electrical Data Remote Converter RCCF31, RCCR31 and
Converter of Intergral Type RCCT3 :
- Driving circuit : terminals D+ / D-
Ex [ib] IIC : Uo = 14.5 V; Io = 47 mA; Po = 0.171 W
Lo = 15 mH; Co = 0.65 F
Ex [ib] IIB : Uo = 11.7 V; Io = 124 mA; Po = 0.363 W
Lo = 8 mH; Co = 10.3 F
- Sensor circuits: terminals S1+/ S1- or S2+ / S2-
Ex [ib] IIB/IIC : Uo = 14.5 V; Io = 47 mA; Po = 0.171 W
Ex [ib] IIC : Lo = 15 mH; Co = 0.65 F
Ex [ib] IIB : Lo = 60 mH; Co = 4.07 F
8
Ex [ib] IIC : Lo = 20 mH; Co = 0.91 F
Ex [ib] IIB : Lo = 80 mH; Co = 5.6 F
- Current output (only option /KF2) :
Ex [ia] IIC : Ui = 30 V; Ii = 165 mA; Pi = 1.25 W
Li = negligible small; Ci = 6.9 nF
- Pulse output (only option /KF2) :
Temperature classifcation see table 7.
FM (For USA and Canada)
Remote Detector RCCS30LR ... 39/XR (Option /FS1) :
- AEx ia IIC, Class 1, Zone 0
- IS Class I, Division 1, Groups A, B, C, D T6
- DIP Class II / III, Division 1, Groups E, F, G
- IP67 / NEMA 4X
- Ambient temperature range : -50C to +80C / -58F to 176F
Remote Converter RCCF31 (Option /FF1) :
- Housing explosion proof
- Provides intrinsically safe detector circuits
- AEx d [ia] IIC, Class I, Zone 1, T6
- AEx d [ia] IIB, Class I, Zone 1, T6 with option /HP
- Class I, Division 1, Groups A, B, C, D
- Class I, Division 1, Groups C, D with option /HP
- Class II / III, Division 1, Groups E, F, G
- AIS Class I / II / III, Division 1, Groups A, B, C, D, E, F, G
- AIS Class I / II / III, Division 1, Groups C, D, E, F, G with /HP
- IP67 / NEMA 4X
Remote Converter RCCR31 (Option /FS1) :
- Intrinsic safe associated apparatus
- Provides intrinsically safe detector circuits
- [AEx ia] IIC, Class I, Zone 1
- [AEx ia] IIB, Class I, Zone 1, T6 with option /HP
- AIS Class I, Division 1, Groups A, B, C, D
- AIS Class I, Division 1, Groups C, D with option /HP
Integral Type RCCT34 ... 39/XR (Option /FF1) :
- Housing explosion proof
- AEx d [ia] IIC, Class I, Zone 1, T6
- AEx d [ia] IIB, Class I, Zone 1, T6 with option /HP
- Class I, Division 1, Groups A, B, C, D
- Class I, Division 1, Groups C, D with option /HP
- Class II / III, Division 1, Groups E, F, G
- IP67 / NEMA 4X
Process Temperature Limits :
- Standard : -50C to 150C / -58F to 302F
- with option /MT : -50C to 220C / -58F to 428F
- with option /HT : 0C to 350C / 32F to 662F
Heat Carrier Fluid Temperature Limits :
- Standard : -50C to 150C / -58F to 302F
- with option /MT : -50C to 220C / -58F to 428F
- with option /HT : 0C to 350C / 32F to 662F
Converter of Intergral Type RCCT3 :
Uo = 14.5 V; Io = 47 mA; Po = 0.171 W
Lo = 15 mH; Co = 0.65 F
- Driving circuit : terminals D+ / D- with option /HP
Uo = 11.7 V; Io = 124 mA; Po = 0.363 W
Lo = 8 mH; Co = 10.3 F
Uo = 14.5 V; Io = 47 mA; Po = 0.363 W
Lo = 15 mH; Co = 0.65 F
Uo = 13.3 V; Io = 40 mA; Po = 0.133 W
Lo = 20 mH; Co = 0.91 F
Electrical Data Remote Detector RCCS30LR ... 33 :
Groups A-D: Ui = 16 V; Ii = 53 mA; Pi = 0.212 W
Groups C,D: Ui = 16 V; Ii = 153 mA; Pi = 0.612 W
Ui = 16 V; Ii = 80 mA; Pi = 0.32 W
Li = 4.2 mH;Ci = negligible small
Ui = 16 V; Ii = 50 mA; Pi = 0.2 W
Groups A-D: Ui = 16 V; Ii = 53 mA; Pi = 0.212 W
Li = 3.2mH; Ci = negligible small
Groups C,D: Ui = 16 V; Ii = 153 mA; Pi = 0.612 W
Li = 3.2mH; Ci = negligible small
Ui = 16 V; Ii = 80 mA; Pi = 0.32 W
Li = 2.1 mH;Ci = negligible small
Ui = 16 V; Ii = 50 mA; Pi = 0.2 W
The remote converter RCCF31 has a T6 temperature class
rating for operation at ambient temperature up to +50C / +122F.
Special conditions :
- ROTAMASS with FM approval is only available with ANSI
1/2 NPT cable conduit connection A.
- The fowmeter must be connected to the potential
equalization system.
- For AC-version maximum power supply is 250V AC.
- For remote type the maximum cable length is 50m / 164ft.
- For remote type at ambient temperature up to 50C / 122F
use remote cable RCCY031 or RCCY032.
- For remote type at ambient temperature from 50C /
122F up to 80C / 176F use remote cable RCCY033 or
RCCY034.
- Use conduit seals within 18 inches for power supply- and
IO- cable entries at RCCT3 / RCCF31.
9
IECEx APPROVAL
Certifcate: IECEx KEM 06.0031X
Remote Detector RCCS30LR ... 39/XR (Option /ES1):
- II 2G Ex ib IIB/IIC T6...T1
- Standard : Ex ibD 21 IP6x T150C
Option /MT : Ex ibD 21 IP6x T220C
Option /HT : Ex ibD 21 IP6x T350C
- Max. surface temperature :
Standard : 150C
/MT : 220C
/HT : 350C
- Ambient temperature range
Standard and option /MT
: -50C to +80C
: -50C to +65C
: -50C to +55C
- Process temperature limits :
- Heat carrier fuid temperature limits :
Remote Converter RCCF31 (Option /EF1) :
- Explosion proof with intrinsic safe connection to detector (ib)
- II 2G Ex d(e) [ib] IIC T6
- II 2G Ex d(e) [ib] IIB T6 with option /HP
20.5 to 28.8 V DC
Remote Converter RCCF31 (Option /EF2) :
- II 2G Ex d(e) [ia] [ib] IIC T6
- II 2G Ex d(e) [ia] [ib] IIB T6 with option /HP
20.5 to 28.8 V DC
Remote Converter RCCR31 (Option /ES1) :
- Associated apparatus with intrinsic safe connection to
detector (ib)
- II (2)G [Ex ib] IIC
- II (2)G [Ex ib] IIB with option /HP
- II (2)D [Ex ibD]
20.5 to 28.8 V DC
WARNING
Remote rack-mount converter RCCR31 must be installed in
safe area !
Integral Type RCCT34 ... 39/XR (Option /EF1) :
- II 2G Ex d(e) [ib] IIC T6 ... T3
- II 2G Ex d(e) [ib] IIB T6 ... T3 with option /HP
20.5 to 28.8 V DC
Integral Type RCCT34 ... 39/XR (Option /EF2) :
- II 2G Ex d(e) [ia] [ib] IIC T6 ... T3
- II 2G Ex d(e) [ia] [ib] IIB T6 ... T3 with option /HP
20.5 to 28.8 V DC
Converter of Integral Type RCCT3 :
Ex [ib] IIC : Uo = 14.5 V; Io = 47 mA; Po = 0.171 W
Lo = 15 mH; Co = 0.65 F
Ex [ib] IIB : Uo = 11.7 V; Io = 124 mA; Po = 0.363 W
Lo = 8 mH; Co = 10.3 F
Ex [ib] IIC : Lo = 15 mH; Co = 0.65 F
Ex [ib] IIB : Lo = 60 mH; Co = 4.07 F
Ex [ib] IIC : Lo = 20 mH; Co = 0.91 F
Ex [ib] IIB : Lo = 80 mH; Co = 5.6 F
- Current output (only option /EF2) :
- Pulse output (only option /EF2) :
Electrical Data Remote Detector RCCS30LR ... 33:
Li = negligible small;
Ci = negligible small
10
- Driving circuit : terminals D+ / D
Li = negligible small;
Ci = negligible small
For customer insulation of RCCS30LR to 39/XR the following must be regarded :
The table "with factory insulation" is calculated with 80 mm insulation and k-factor = 0.4 W/m
2
K.
If your insulation data are worse than these use table "without insulation" !
Table 7 : Temperature classifcation for ATEX, FM, IECEx, INMETRO, NEPSI and KOSHA certifed fowmeter
RCCS30LR to RCCS33
without insulation
RCCS30LR to RCCS33
with factory insulation
Temp. class Max. ambient
temperature
Max. process
temperature
Max. ambient
temperature
Max. process
temperature
T6 50C / 122F 60C / 140F 60C / 140F 60C / 140F
T5 50C / 122F 80C / 176F 80C / 176F 90C / 194F
T4
80C / 176F
50C / 122F
100C / 212F
120C / 248F
80C / 176F 130C / 266F
T3 80C / 176F 150C / 302F 80C / 176F 150C / 302F
T2 80C / 176F 150C / 302F 80C / 176F 150C / 302F
RCCS34 to RCCS39/XR
without insulation
RCCS34 to RCCS39/XR
with factory insulation
RCCT34 to RCCT39/XR
Temp. class Max. ambient
temperature
Max. process
temperature
Max. ambient
temperature
Max. process
temperature
Max. ambient
temperature
Max. process
temperature
T6 40C / 104F 40C / 104F 65C / 149F 65C / 149F 55C / 122F 65C / 149F
T5 55C / 131F 55C / 131F 75C / 167F 75C / 167F 55C / 122F 80C / 176F
T4
80C / 176F
40C / 104F
100C / 212F
120C / 248F
70C / 158F 115C / 239F 55C / 122F 115C / 239F
T3
80C / 176F
40C / 104F
160C / 320F
180C / 356F
70C / 158F 180C / 356F 55C / 122F 150C / 302F
T2 80C / 176F 220C / 428F 65C /149F 275C / 527F 55C / 122F 150C / 302F
T1 80C / 176F 220C / 428F 45C / 113F 350C / 662F 55C / 122F 150C / 302F
INMETRO APPROVAL (For Brazil)
RCCS3x with option /US1.same as IECEx /ES1
RCCT3x with options /UF1 ... /UF2 same as IECEx /EF1 ... /EF2
RCCF31 with options /UF1 ... /UF2 same as IECEx /EF1 ... /EF2
RCCR31 with option /US1 same as IECEx /ES1
Same parameters and specifcations as IECEx approval.
NEPSI APPROVAL (For China)
RCCS3x with option /NS1 same as IECEx /ES1
RCCT3x with options /NF1 ... /NF2 same as IECEx /EF1 ... /EF2
RCCF31 with options /NF1 ... /NF2 same as IECEx /EF1 ... /EF2
RCCR31 with option /NS1 same as IECEx /ES1
KOSHA APPROVAL (For Korea)
Meter with IECEx option must be ordered.
METROLOGICAL REGULATION IN CIS (GOST)
Rotamass has Pattern Approval Certifcate of Measuring
Instruments and is registered as a measuring instrument in
Russia, Kazakhstan, Uzbekistan, Belarus and Ukraine.
The calibration laboratory of Rota Yokogawa is approved by
Federal Agency on Technical Regulating and Metrology in
Russia and other Metrological Organizations in CIS countries
to issue primary calibration confrmation for ROTAMASS,
option /QR[].
Furthermore ROTAMASS is RTN (GGTN) approved for
installation in hazardous areas.
For export to CIS countries please contact your Yokogawa
representative.
11
Heat Tracing and Insulation
Basically the detector can be insulated by the customer.
To be sure not to overheat the connection box choose one
of /Tx options (insulation or heat tracing from Yokogawa). For
temperatures between 150C and 230C choose /MT option
and remote installation. For low temperature fuids ask for
special insulation. If Rotamass detector with /MT or /HT is not
insulated, the accuracy specifcation can not be guaranteed.
The converter should not be exceeded more than 50C.
Therefore never insulate the converter and keep the neck
free from insulation too. Yokogawa will not take any liability
regarding customer insulation.
Relations between Options /MT, /HT, /S2 and /Tx ( /T1,
/T2, /T3)
The meters with high temperature options (/MT, /HT) can
be insulated either by the customer by using option /S2
(prolonged neck) or by the factory through options /Tx.
The /Tx options already include the option /S2 so that the
/S2 option can not be selected in case of the /Tx options.
If the meter is not properly insulated by the customer, the
accuracy specifcation can not be guaranteed.
Installation above 100C Process Temperature
To provide enough cooling the instrument should be installed
vertically or horizontally with the converter down. This is
recommended for size RCCTx36 and larger without /Tx
option.
Installation below 0C Process Temperature
The detector can be insulated to prevent ice capping either
by the customer or by the manufacturer. Ask your Yokogawa
representative for special insulation. If the customer wants
to insulate by themselves a closed cell foam as insulation
material is recommended to avoid water siphon. In this case
option /S2 should be selected. For temperatures below -70C
option /LT is recommended (on request).
Zero Adjustment Function
Zero point can be adjusted either by setting the switches on
display or with the HART
communication or with status

input when the fuid fow is stopped and the detector flled.
To ensure no fow conditions isolation valves should be
installed. To achieve the specifed accuracy a zero should
be performed at process conditions (temp., pressure).
Pressure / Temperature Dependencies of Process Connections
See also process pressure limits in chapter Normal operation
conditions.
Rupture Disk
The rupture disk is used as annunciation method in the case
of tube rupture (Dual Seal) preferable for high pressure
gas service. Practically a tube rupture of ROTAMASS is
not known to the manufacturer. For large sizes it cannot be
expected that the full line pressure can be released via the
rupture disk. If this is requested please contact Yokogawa
for a special execution.
PLANNING AND INSTALLATION HINTS
Design Limits
It is the responsibility of the user to use the instrument within
the given design limits. Erosion and corrosion infuence the
accuracy and may restrict the temperature / pressure limits.
Therefore corrosion and erosion should be avoided.
Installation
The fowmeter can be installed vertically, horizontally or
in any other position, as long as the measuring tubes are
completely flled with the measured liquid during measurement.
Redundant Installation
If two fowmeters of the same size are installed in series
mutual interference called cross talk may take place. Cross
talk occurs due to the fact that both meters have the same
resonance frequency. If serial installation is planned please
contact your Yokogawa representative who can ensure that
a frequency adjustment is made to one of the meters at the
factory.
Sizing
The measuring range and accuracy are virtually independent
of fuid conditions and size of the connecting pipe. Select a
suitable nominal size from pressure loss calculation. Check
whether the measuring range and accuracy at minimal fow
ft the application. The calculations of the pressure loss are
based on Newtonian fuids. For correct calculation of the
pressure drop use the YOKOGAWA Sizing software.
Sanitary Applications
For sanitary applications select process connection S2, S4 or
S8. The wetted surface will be Ra 1.6 m. However, if
option /SFx is selected the surface roughness will be
Ra < 0.8m and with /SF2 a certifcate with a 3- point
roughness measurement certifcate is delivered. The EHEDG
certifcate shows that ROTAMASS conforms to the EHEDG
criteria regarding the capability to be cleaned by a CIP pro-
cess. The evaluation does not include the process
connections and seals.
Cavitation
To avoid cavitation keep the back pressure of the fuid suffi-
ciently above the vapor pressure of the fuid. For low viscous
fuids following condition should be fulflled at the given
temperature:
p
back
> p
vapor
+ 0.7*p
With p = pressure loss (e.g. given by the Yokogawa sizing
software)
Long Term Stability
To get stable defection of the tubes by the Coriolis forces the
stiffness and therefore the wall thickness has to kept constant
during measuring. With corrosion or erosion the meter factor
is drifting with time and recalibration is necessary. Select the
suitable resistant tube material for the process!
Recalibration Service
Yokogawa offers via its European Flow Centre (Rota Yokogawa,
Germany) full recalibration service, if necessary with a
certifcate traceable to German national standards. Please
contact your Yokogawa affiliate or directly Rota Yokogawa,
Germany.
12
Density Measurement
There are 3 levels of density measurement. The standard adjustment and /K4 delivers an accuracy up to 0.001 g/cm, if the fuid den-
sity is around 1 kg/l. However, at elevated temperatures the density error may increase. For option /K4 the instrument is
preheated ensuring long term stability. However, if high density stability is needed at high temperatures option /HT is recommended.
Option /K6 includes preheating, a full calibration at 3 different densities, increased temperature measurement specifcation and individual
adjustment of the fuid temperature dependency. Multiphase fow can generate higher deviations. The higher the density differences of
the single components are the more likely it is that a negative density error is generated. Aeration has to be avoided fully to receive
good density measurement.
For more information please see TI 01R04B04-05E Density Measurement with ROTAMASS.
Note: Density specifcation under calibration condition only with fow direction forward according the arrow on the meter.
Table 8: Overview density-/volume- fow measurement:
Option Accuracy Certifcate Description Typical Application
Standard 0.0015 g/cm to
0.02 g/cm
Standard (mass fow)
factory calibration
certifcate
- Standard adjustment with water and air
- Density constants given in mass fow
certifcate
- Process medium and environment are
approximately at room temperature, the density
range is 0.9 kg/l to 1.1 kg/l
Option /K4 0.001 g/cm Standard (mass fow)
factory calibration
certifcate
- Thermal treatment of the sensor and
special hardware design
- Standard adjustment with water and air
- Density constants given in mass fow
certifcate
- Improved volume fow accuracy
- Process medium up to 150C, for higher
temperature select option /HT
- Density range is 0.9 kg/l to 1.1 kg/l
Option /K6 0.0005 g/cm Separate factory
density calibration
certifcate
- Thermal treatment of the sensor and
special hardware design
- Density calibration with 3 different liquids
- Individual adjustment of the fuid
temperature dependency
- Density and concentration measurement in
addition to the mass fow:
- Process medium up to 150C, for higher
temperature select option /HT
- Density range 0.3 kg/l to 2.5 kg/l
- Best volume fow accuracy
Explosion Proof Concept
The detector is intrinsically safe Ex ib, the converter RCCT
and RCCF31 are fame (explosion) proof. The converter
RCCR31is an intrinsically safe associated apparatus. The
driving power from converter to detector is limited and
protected by an intrinsically safe barrier, which is part of the
converter. The barrier is protecting the detector either for gas
group IIC or IIB (option /HP).
Option /KF2 delivers one passive intrinsic safe current and
one pulse output, however the converter is fame (explosion)
proof.
Option /HP
With option /HP the detector driving power is higher which is
beneft to 2 phase fow. This is also true for non hazardous
applications.
Gas Measurement
For gas applications please choose the option /GA.
Density reading below 0.3 kg/l is not possible. Volume fow is
calculated by using the fx density value stored in Reference density.
Based on the selection of the gas density, the following volume
fow rates can be calculated; standard, reference, normal.
Besides, the corresponding volume fow rate units can be
selected. Some functions are unavailable for gas measurement,
including concentration measurement, empty pipe, slug or corrosion
detection.
Good and stress free installation is mandatory for a stable Zero.
Attention to resonance phenomenons has to be taken if gas
compressors are used in the pipe. Flow noise has to be avoided.
Batch Process
The specifed mass fow accuracy applies if the batch process
is >1 minute. For shorter batch time (Dt in s) the accuracy
decreases with the square root of 60/Dt.
For short batches the opening and closing times of the valves
have to be longer than 2 seconds.
Concentration Measurement for Liquids
The Standard Concentration Measurement (option /CST)
is suitable for concentration measurement of emulsions or
suspensions, where the density of the solid is assumed to
be fx. It can also be used for (mainly low concentration)
solutions if the two fuids are not strongly interacting. The
density change of the liquid components due to temperature
can normally be described with a linear or quadratic function
with very high accuracy within the desired measurement
range. The coefficients of these function (linear and quadratic
thermal expansion coefficients) must be either known or have
to be determined prior to using this function.
For interacting liquids the Advanced Concentration
Measurement options should be used, these options
can be ordered using the appropriate /Cxx concentration
measurement option. For more information please see
TI 01R04B04-04E-E Concentration Measurement with
ROTAMASS.
13
Type of process connection
1)
Process Temperature
RT
2)
50C
(120F)
100C
(210F)
150C
(300F)
200C
(390F)
250C
(480F)
300C
(570F)
350C
(660F)
A1 Flange acc. ASME B16.5 Class 150 15.9 bar 15.3 bar 13.2 bar 12.0 bar 11.0 bar 10.2 bar 9.7 bar 8.4 bar
A5
Flange acc. ASME B16.5 Class
1500
206.8 bar 200.1 bar 173.9 bar 157.0 bar 145.8 bar 137.3 bar 130.3 bar 125.4 bar
D2 Flange acc. EN 1092-1 PN 16 16 bar 15.6 bar 14.2 bar 12.8 bar 11.7 bar 10.9 bar 10.3 bar 9.9 bar
G9 Internal thread (RCCS30LR...33)
See tube pressure. for option /DS max. pressure
according A4. ASME class 900
------------------------------------------------------------------------
T9 Internal thread NPT (RCCS30LR...33)
See tube pressure. for option /DS max. pressure
according A4. ASME class 900
------------------------------------------------------------------------
G9 Internal thread (RCCS34) See tube pressure. for option /DS max. pressure according A4. ASME class 900
T9 Internal thread NPT (RCCS34) See tube pressure. for option /DS max. pressure according A4. ASME class 900
Process Temperature
up to 120C (248F) 220C (428F) 300C (572F) 350C (662F)
J1 Flange acc. JIS B 2220 10K 14 bar (203 psi)
12 bar
(174 psi)
10 bar
(145 psi)
------
J2 Flange acc. JIS B 2220 20K 34 bar (493 psi)
31 bar
(449 psi)
29 bar
(420 psi)
26 bar
(377 psi)
Process Temperature
up to 140C (284F)
*)
S2
Pipe connection up to DN 40
acc. DIN 11851 DN 50 to DN 100
above DN 100
40 bar (580 psi)
*)
under the restriction using suitable gasket materials 25 bar (362 psi)
16 bar (232 psi)
Process Temperature
up to 150C (302F)
**)
S4
Clamp connection up to DN 50
acc. DIN 32676 above DN 50
16 bar (232 psi)
**)
under the restriction using suitable gasket materials
10 bar (145 psi)
S8
Clamp acc. Mini-Clamp up to 1/2 16 bar (232 psi)
Clamp acc. Tri-Clamp

up to 2
above 2
16 bar (232 psi)
10 bar (145 psi)
1)
all process connections are made of material 1.4404 / 1.4435 (equivalent to group 2.3 material AISI 316L acc. ASME B16.5)
2)
RT = Room Temperature; EN1092: -10C to 50C; ASME B16.5: -29C to 38C (-20F to 100F)
Table 9 : Pressure rating
14
Note: The fange dimensions depend on size and pressure rating of the fange.
Model L1 L2 L3 H1 H2 H3 H4 W1 W2 Weight
RCCT34 [mm] see table 11 272 212 177 212 278 80 60 80 13 kg
RCCT39/IR [mm] see table 11 870 454 435 272 338 200 154 200 113 kg
Dimensions in [mm]. Weights with smallest fanges.
DIMENSIONS
Integral Type RCCT34 - 38 and 39/IR
15
L15
L2
L3
H
4
W1
H
3
H
1
W2
H
2
(147)
(
6
5
)
85
(266)
122 144
32 50
30
4
9
1
2
3
Integral Type RCCT39/XR
see table 11
L1 5 see table 11
Dimensions in mm
Weight: RCCT39/XR: 295 ... 325 kg (650 ... 720 lb) depends on flanges
Dimensions in mm
Weight: RCCS39/XR: 290 ... 320 kg (640 ...710 lb) depends on flanges
Integral Type RCCT39
Note: The fange dimensions are depended on its respective size and pressure rating.
Model L1 L2 L3 H1 H2 H3 H4 W1 W2 Weight
16
Remote feld-mount Converter RCCF31
75
2
0
1
3
0
5
1
7
1
2
0
6
4
85
(148)
102
1
2
3
9
1
.
6
32 29 49
144 122
2
0
1
3
0
5
75
85
148
6
4
1
2
0
1
7
1
2
3
9
1
.
6
32 29 29
102
124 122
F2.EPS
1
2
2
1
2
2
Weight with bracket: about 5.5 kg (depends on type)
Without window
With window
Remote rack-mount Converter RCCR31
Terminal Board Cassette, side view Cassette, front view
228 107 (21TE)
1
2
8

(
3
H
E
)
Dimensions in mm
19-inch rack, acc. IEC / DIN EN 60297-3-101
Weight: 1.5 kg
17
Remote Detector RCCS30LR - 33
Option /PD
Mounting set for DN50 tube
25 58 47
210
180
150
8
.
5
1
1
0
1
5
0
s
.

t
a
b
l
e

1
1

3
9
8
Weight (without flanges): 5.2 kg (11.5 lb) Weight (without flanges): 6.2 kg (13.5 lb)
1
0
2
8
9
126
201
51
29 20 25
Option /S2
Dimensions in mm
111 (RCCS30LR)
111 (RCCS30)
99 (RCCS31)
89 (RCCS32)
55 (RCCS33)
Remote Detector RCCS34 - 38 and 39/IR
Model L1 L2 L3 H1 W1 W2 H4 H5 H6 Weight
RCCS34 [mm] see table 11 272 212 177 60 80 80 138 218 9.5 kg
RCCS36 [mm] see table 11 400 266 230 76 90 80 138 218 13 kg
RCCS39/IR [mm] see table 11 870 454 435 154 200 200 198 278 110 kg
18
Remote Detector RCCS39/XR
see table 11
L1 5 see table 11
Dimensions in mm
Weight: RCCT39/XR: 295 ... 325 kg (650 ... 720 lb) depends on flanges
Dimensions in mm
Weight: RCCS39/XR: 290 ... 320 kg (640 ...710 lb) depends on flanges
Remote Detector RCCS39
Note: The fange dimensions are depended on its respective size and pressure rating.
Model L1 L2 L3 H1 W1 W2 H4 H5 H6 Weight
L15
L2
L3
W1
H
4
H
5
H
1
H
6
102
102
8
0
Option /S2 and /MT
W
2
19
Remote Detector RCCS39/XR with option /HT
2
8
0
683
1140
273
2
8
0
8
9
2
3
1
8
8
0
50
102 L1 5 s. table 11
F22.EPS
20
Remote Detector RCCS34 - 39/IR with option /Tx (Insulation / Heating)
Model L1 L4 L5 D1 D2 H6 H7 H8 H9 W3 Weight
RCCS34 mm see table 11 420 310 200 330 218 411 273 138 240 18 kg
RCCS39/IR mm see table 11 1040 932 350 570 278 726 528 198 342 125 kg
Weights with smallest fanges including insulation cover and heat tracing.
Standard heating connection according table 10.
21
Table 10: Heat tracing connection types depending on process connection type
Process connection Standard heating connection *)
Ax ASME - 150
Dx EN DN 15 PN 40
Jx JIS 10K DN15
S2 ; S4 EN DN 15 PN 40
S8 ASME - 150
G9 EN DN 15 PN 40
T9 ASME - 150
*) others on request
Adapter 1/2 NPT - G1/2 (option /AD2)
N1 N2 D B C L1 L2 L Weight (kg)
1/2 NPT G1/2 15 27 30 19 23 45 0.07
Unit: mm
Remote Detector RCCS30LR - 33 with option /Tx (Insulation / Heating)
ventilation optional /T3
heating connection
optional /T2 or /T3
160
176
180
270
3
5
0
1
2
6
1
6
5
4
2
5
2
9
9

1
0
2
F21.EPS Dimensions in mm
L1 3 s. table on page 4
1
3
4
22
MODEL, SUFFIX AND OPTION CODES
Integral Type RCCT3, Model and Suffix Code
Model Suffix Code Description Restrictions
RCCT34
RCCT36
RCCT38
RCCT39
RCCT39/IR
RCCT39/XR
Nominal Value : 3 t/h = 50 kg/min
Nominal Value : 500 t/h = 8340 kg/min only with /HP
Power supply -A
-D
90 - 264 V AC
24 V DC
Indicator direction H1
H2
V0
N0
Detector installation horizontal, tubes down
Detector installation horizontal, tubes up
Detector installation vertical
Without indicator
recom. for liquid service
recom. for gas service /GA
Cable conduit connection M
A
M20 x 1.5, female thread with cable glands
ANSI NPT, female thread without cable glands mandatory with /FF1, /FF2
Process connection size
1)
23
01
02
04
05
06
08
10
12
15
20
DN 15,
DN 25, 1
DN 40, 1
DN 50, 2
DN 65, 2
DN 80, 3
DN 100, 4
DN 125, 5
DN 150, 6
DN 200, 8
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
Process connection rating and style
1)
A1
A2
A3
A4
A5
D2
D4
D5
D6
J1
J2
S2
S4
S8
G9
T9
ASME fange class 150, process connection dim. + facing acc. ASME B16.5
EN fange PN 16, process connection dim. + facing acc. EN 1092-1 Form B1
JIS fange 10K, JIS B 2220
Thread acc. DIN 11851
Clamp, process connection dimensions acc. DIN 32676
Clamp, process connection dim. acc. Tri-Clover (Tri-Clamp) and Mini Clamp
G, female thread
NPT female thread
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
Material of wetted parts
1)
SL
HC
Stainless steel 316L (1.4404)
Hastelloy C-22 (2.4602) only RCCT34 to 39/IR

1)
see selection table Process connection and materials (table 11)
Integral Type RCCT3, Option Code :
Options Option
code
Description Restrictions
Hazardous Area Approvals /KF1
/KF2
/FF1
/FF2
/EF1
/EF2
/UF1
/UF2
/NF1
/NF2
ATEX Flame proof converter + Intrinsic safe detector
ATEX Flame proof converter + Intrinsic safe detector + Intrinsic safe outputs
FM approval for USA+Canada, Flame proof converter + Intrinsic safe detector +
2 active analog outputs + 2 passive pulse outputs + 1 status input
FM approval for USA+Canada, Flame proof converter + Intrinsic safe detector +
1 passive analog output + 1 passive pulse output
IECEx Flame proof converter + Intrinsic safe detector
IECEx Flame proof converter + Intrinsic safe detector + Intrinsic safe outputs
INMETRO Flame proof converter + Intrinsic safe detector
INMETRO Flame proof converter + Intrinsic safe detector + Intrinsic safe outputs
NEPSI Flame proof converter + Intrinsic safe detector
NEPSI Flame proof converter + Intrinsic safe detector + Intrinsic safe outputs
with /HP for gas group IIB
only with cable conduit A; with /HP not for groups
A and B
only with cable conduit A; with /HP not for groups A
and B
Custody Transfer Measurement
acc. OIML R 117-1
/Q01 European MID Approval (fuids other than water) (refer to GS 01R04B07-00E)
GOST /QR1
/QR2
/QR3
Primary Calibration and Test Confrmation valid in Russia
Primary Calibration and Test Confrmation valid in Kazakhstan
Primary Calibration and Test Confrmation valid in Uzbekistan
see page 9
see page 9
see page 9
Dual Seal Approval /DS
/RD
Dual Seal approval (conform with ANSI/ISA-12.27.01)
Rupture disk, rupture pressure 20 bar, nominal diameter 8 mm
only with /FF1; not with process connection A5;
preferable with /GA, mandatory if /DS+/GA is selected
23
Integral Type RCCT3, Option Code (continued)
Options Option
code
High Driving Power /HP High Driving Power not for RCCT34, recommended for RCCT36 to 39,
strongly recommended for RCCT39/IR, mandatory for
RCCT39/XR
1);
Please see Hazardous Area Specifcations
Communication /MB1 Modbus communication protocol for selected parameters and values not with /Q01, /KF2, /EF2, /UF2, /FF2, /NF2
Active Pulse Output /AP One active pulse output not with /KF2, /EF2, /UF2, /NF2, /NM
NAMUR Switch /NM One pulse output acc. to EN 60947-5-6 (NAMUR) not with /AP
Tag Number /BG With customer specifed tag number on name plate max. 16 digits
HART
Tag Number (Software Tag) /BT1 With customer specifed tag number for HART
communication in converter 8 digits for tag, 22 digits for long tag

Flange Facing /DN
/RJ
Flange with safety grooves acc. to EN 1092-1 form D
Ring Type Joint Flanges
only for D2 to D6; not HC
only for A3, A4, A5; not HC
Gas Measurement /GA Gas measurement, special factory adjustments and settings to be conform with ANSI/ISA-12.27.01 select /RD
Special Calibration /K2
2)
/K4
/K5
2)
/K6
Custom 5 pts mass-/volume-fow calibration using water with factory certifcate
(traceable to German national standards)
Density adjustment + thermal treatment; (accuracy: 0.001 g/cm)
Custom 10 pts mass-/volume-fow calibration using water with DKD certifcate
(according EN-17025:2005)
Density calibration with 3 different fuids incl. individual temperature compensation
with certifcate (accuracy: 0.0005 g/cm)
only RCCT34 to 39; not with /GA
only RCCT34 to 39; not with /GA
Certifcates /P2
/P3
/P6
/P8
/H1
/WP
Certifcate of compliance with the order acc. to EN 10204:2004 -2.1
As /P2 + Test report acc. to EN 10204: 2004 -2.2 (QIC)
Material certifcate acc. to EN 10204: 2004 -3.1
Pressure test report measuring system
Oil and fat free for wetted surface acc. to ASTM G93-03 level C
WPS acc. DIN EN ISO 15609-1 (Welding Procedure Specifcation)
WPQR acc. DIN EN ISO 15614-1 (Welder Performance Qualifcation Record)
WQC acc. DIN EN 287-1 (Welder Qualifcation Certifcate)
only for butt weld between process connection and
fow divider; not for material HC
Sanitary Type /SF1
/SF2
/SA
/SE
Surface roughness Ra = 0.8 m
As /SF1 + Test report roughness of wetted parts
As /SF2 + 3A- declaration of conformity and 3A- mark
As /SF2 + EHEDG certifcate
not RCCT39/XR; only process connections S2, S4, S8;
see also restrictions in table 11
not with process connection S2
Customer Presetting /PS Presetting sheet with customer data has to be issued with the order
Housing Pressure Test /J1 Rupture pressure proof test and certifcate (see page 4) not for RCCT39/XR
X-Ray Examination /RT X-ray examination of fange welding RCCT34 with /K4 or /K6 only one-sided
PMI Examination /PM6 PAMI test (6 test points: process connection inlet + outlet, measuring tubes, fow
divider inlet + outlet)
3)
Dye Penetration Test /PT Dye penetration test of fange welding
Epoxy Coating /X1 Epoxy coating of converter housing
Concentration Measurement
4)
/CST
/Cxx
Standard concentration measurement
Advanced concentration measurement, details see table Advanced Concentration
Measurement Options
not with /GA
not with /GA
Delivery to Japan /PJ For meters which are delivered to Japan, with SI-unit preset
Delivery to Korea /KC With KC-mark for Korea
Cable glands /AD2 2 pcs ANSI 1/2 NPT / G1/2 adapter only with cable conduit A
Instruction Manuals /IEn
/IDn
/IFn
Quantity of instruction manuals in English
Quantity of instruction manuals in German
Quantity of instruction manuals in French
n = 1 to 3 selectable
5)
5)
5)
Quick Delivery /QD Delivery within 24 hours from factory Delivery scope please refer to Quick Delivery Possibili-
ties or contact Yokogawa sales office.
Special order /Z Special design must be specifcation an extra sheet
1)
For gas application /GA RCCT39/XR can also be ordered without /HP.
2)
Calibration order sheet must be delivered with the order. This is available on the Flow Center Page at Coriolis/RCCx3/Technical Information.
3)
Measuring tube PAMI test is performed per delivery batch.
4)
For detailed information please see TI 01R04B04-04E-E. Concentration measurement is recommended with option /K6.
5)
If no instruction manual is selected, only a DVD with instruction manuals is shipped with the instrument. More than 3 manuals of one language on request.
24
Remote Detector RCCS3, Model and Suffix Code
Model Suffix Code Description Restrictions
RCCS30LR
RCCS30
RCCS31
RCCS32
RCCS33
RCCS34
RCCS36
RCCS38
RCCS39
RCCS39/IR
RCCS39/XR
Nominal Value : 0.021 t/h = 0.35 kg/min
Nominal Value : 0.95 t/h = 16 kg/min
Nominal Value : 500 t/h = 8340 kg/min select affiliated RCCF31 or
RCCR31 with /HP
Cable conduit connection -M
-A
ANSI NPT, female thread only with cable gland for detector connection mandatory with /FS1
Process connection size
1)
41
01
23
02
04
05
06
08
10
12
15
20
DN 15,
DN 25, 1
DN 40, 1
DN 50, 2
DN 65, 2
DN 80, 3
DN 100, 4
DN 125, 5
DN 150, 6
DN 200, 8
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
Process connection rating and style
1)
A1
A2
A3
A4
A5
D2
D4
D5
D6
J1
J2
S2
S4
S8
G9
T9
Thread acc. DIN 11851
Clamp, process connection dimensions acc. DIN 32676
Clamp, process connection dim. acc. Tri-Clover (Tri-Clamp) and Mini Clamp
G female thread
NPT female thread
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
see table 11
Material of wetted parts
1)
SH
SL
HC
316L (1.4404) and Hastelloy C-22 (2.4602) for tube
Stainless steel 316L (1.4404)
Hastelloy C-22 (2.4602)
only RCCS30LR to 33
only RCCS34 to 39/XR
only RCCS34 to 39/IR

1)
see selection table Process connection and materials (table 11)
25
Remote Detector RCCS3, Option Code
Options Option
code
Hazardous Area Approvals
1)
/KS1
/FS1
/ES1
/US1
/NS1
ATEX intrinsically safe approval
FM intrinsically safe approval for USA + Canada
IECEx intrinsically safe approval
INMETRO intrinsically safe approval for Brazil
NEPSI intrinsically safe approval for China
only with cable conduit A
acc. OIML R 117-1
GOST
1)
/QR1
/QR2
/QR3
see page 9; not with RCCS30LR
Dual Seal Approval /DS
/RD
Dual Seal approval (conform with ANSI/ISA-12.27.01)
Rupture disk, rupture pressure 20 bar, nominal diameter 8 mm
only RCCS34 to 39/XR; only with /FS1; not with pro-
cess connection A5
only RCCS34 to 39/XR, preferable with /GA, not with /
Tx, mandatory if /DS + /GA is selected
Flange Facing /DN
/RJ
Flange with safety grooves acc. to EN 1092-1 form D
Ring Type Joint Flanges
only for D2 to D6; not HC, for RCCS30LR only for 01D4
or 01D6
only for A3, A4, A5; not HC, for RCCS30LR only for
01A3 or 01A5
Gas Measurement /GA Gas measurement, special factory adjustments and settings select affiliated RCCF31 or RCCR31 with /GA;
to be conform with ANSI/ISA-12.27.01 select /RD
Low temperature version /LT -200C < T
medium
< 150C not RCCS30LR to 33; not with /KS1, /FS1, /ES1, /US1,
/MT, /HT, /T1, /T2, /T3
Extended temperature range /MT -70C < T
medium
< 230C not RCCS30LR to 33; always with /S2 or /Tx;
remote cable RCCY033/034 recommended
High temperature version /HT T
medium
up to 350C RCCS34 to 39/IR only with /Tx or /S2 (customer insula-
tion required); RCCS39/XR only with /S2;
remote cable RCCY033/034 recommended
Special Calibration /K2
2)
/K4
/K5
2)
/K6
Custom 5 pts mass-/volume-fow calibration using water with factory certifcate
(traceable to German national standards)
Density adjustment + thermal treatment; (accuracy: 0.001 g/cm)
Custom 10 pts mass-/volume-fow calibration using water with DKD certifcate
(according EN-17025:2005)
Density calibration with 3 different fuids incl. individual temperature compensation
with certifcate (accuracy: 0.0005 g/cm)
only RCCS31 to 39; not with /GA
only RCCS32 to 39; not with /GA; not with /LT;
not with /MT; only available if converter is also ordered
Certifcates /P2
/P3
/P6
/P8
/H1
/WP
Certifcate of compliance with the order acc. to EN 10204:2004 -2.1
As /P2 + Test report acc to EN 10204: 2004 -2.2 (QIC)
Material certifcate acc to EN 10204: 2004 -3.1
Pressure test report measuring system
Oil and fat free for wetted surface acc. to ASTM G93-03 level C
WPS acc. DIN EN ISO 15609-1 (Welding Procedure Specifcation)
WPQR acc. DIN EN ISO 15614-1 (Welder Performance Qualifcation Record)
WQC acc. DIN EN 287-1 (Welder Qualifcation Certifcate)
only for butt weld between process connection and
fow divider; not for HC
Sanitary Type /SF1
/SF2
/SA
/SE
Surface roughness Ra = 0.8 m
As /SF1 + Test report roughness of wetted parts
As /SF2 + 3A- declaration of conformity and 3A- mark
As /SF2 + EHEDG- certifcate
only RCCS34 to 39/IR; only process connections S2,
S4, S8; see also restrictions in table 11
Mounting set /PD 2 inch pipe mounting set only RCCS30LR to 33; not with /Tx; recommended for
RCCS30LR and RCCS30
Housing Pressure Test /J1 Rupture pressure proof test and certifcate (see page 4) not for RCCS30LR to 33 + RCCS39/XR
Customer insulation / Heating /S2 Terminal box on extension for high or low process temperature not with /T1 ... /T3
Factory Insulating / Heating /T1
/T2
/T3
Insulation
Insulation + Heat carrier heating
Insulation + Heat carrier heating with ventilation (purge)
not for RCCS39/XR
not for RCCS39/XR
not for RCCS39/XR
X-Ray Examination /RT X-ray examination of fange welding RCCS30LR to 33 and RCCS34 with /K4, /K6 or /LT
only one-sided
PMI Examination /PM4
/PM6
PAMI test (4 test points: process connection inlet + outlet, fow divider inlet +
outlet)
3)
PAMI test (6 test points: process connection inlet + outlet, measuring tubes, fow
divider inlet + outlet)
3)
only RCCS30LR to 33
not RCCS30LR to 33
Dye Penetration Test /PT Dye penetration test of fange welding
Stainless steel cable gland /BS Cable gland stainless steel
Delivery to Japan /PJ For meters which are delivered to Japan
Quick Delivery /QD Delivery within 24 hours from factory Delivery scope please refer to Quick Delivery Possibili-
ties or contact Yokogawa sales office.
1)
Select affiliated converter RCCF31/RCCR31 with the same approval type (e.g. ATEX).
2)
Calibration order sheet must be delivered with the order. This is available on the Flow Center Page at Coriolis/RCCx3/Technical Information.
3)
Measuring tube PAMI test is performed per delivery batch.
26
Remote feld-mount Converter RCCF31, Model, Suffix and Option Code
Model Suffix Code Option
Code
RCCF31 Remote feld-mount converter to be connected to RCCS3;
when ordered without detector combination option /NC must be selected
Power supply -A
-D
90 - 264 V AC
24 V DC
Indicator direction H2
N0
With indicator
Without indicator
Cable conduit connection M
A
ANSI NPT, female thread, only cable gland for detector connection mandatory with /FF1, /FF2
Hazardous Area Approvals /KF1
/KF2
/FF1
/FF2
/EF1
/EF2
/UF1
/UF2
/NF1
/NF2
ATEX Flame proof converter + Intrinsic safe detector output
ATEX Flame proof converter + Intrinsic safe detector output + Intrinsic safe
outputs
FM approval for USA+Canada, Flame proof converter + Intrinsic safe detector
output + 2 active analog outputs + 2 passive pulse outputs + 1 status input
FM approval for USA+Canada, Flame proof converter + Intrinsic safe detector
output + 1 passive analog output + 1 passive pulse output
IECEx Flame proof converter + Intrinsic safe detector output
IECEx Flame proof converter + Intrinsic safe detector output + Intrinsic safe
outputs
INMETRO Flame proof converter + Intrinsic safe detector
INMETRO Flame proof converter + Intrinsic safe detector output + Intrinsic safe
outputs
NEPSI Flame proof converter + Intrinsic safe detector output
NEPSI Flame proof converter + Intrinsic safe detector output + Intrinsic safe
outputs
A and B
A and B
acc. OIML R 117-1
GOST
1)
/QR1
/QR2
/QR3
see page 9
see page 9
see page 9
Communication /MB1 Modbus communication protocol for selected parameters and values not with /Q01, /KF2, /EF2, /UF2, /FF2, /NF2
High Driving Power /HP High Driving Power not for combination with RCCS30LR to 34,
recommended for combination with RCCS36 to 39,
strongly recommended for combination with RCCS39/IR,
mandatory for combination with RCCS39/XR
4)
Active Pulse Output /AP One active pulse output not with /KF2, /EF2, /UF2, /NF2, /NM
NAMUR Switch /NM One pulse output acc. EN 60947-5-6 (NAMUR) not with /AP
HART

Gas Measurement /GA Gas measurement, special factory adjustments and settings select affiliated RCCS3 with /GA
Combination with RCCS39/XR /XR Special converter adjustment with RCCS39/XR mandatory for combination with RCCS39/XR
No Combination /NC No combination with detector
Epoxy Coating /X1 Epoxy coating of converter housing
Delivery to Japan /PJ For meters which are delivered to Japan with SI-unit preset
Cable glands /AD2 2 pcs ANSI 1/2 NPT / G1/2 adapter only with cable conduit A
2)
/CST
/Cxx
Measurement Options
not with /GA
not with /GA
/IDn
/IFn
3)
3)
3)
Quick Delivery /QD Delivery within 24 hours from factory Delivery scope please refer to Quick Delivery Pos-
sibilities or contact Yokogawa sales office.
1)
Select affiliated RCCS3 with the same approval type (e.g. /KFx with /KS1).
2)
For detailed information please see TI 01R04B04-04E-E. Option /K6 of RCCS3 is recommended with concentration measurement.
3)
4)
RCCF31 in combination with RCCS39/XR with gas application /GA can also be ordered without /HP.
27
Remote Cable RCCY03, Model, Suffix and Option Code
Code
RCCY031
RCCY032
RCCY033
RCCY034
Length in meter
Length in feet
Length in meter
Length in feet
max. ambient temperature 70C; with /FFx or /FS1: 50C
Cable ends -0
-1
No termination, with one termination kit
Terminated
Cable length Lxxx Enter the length max. 300m / 999ft (with /FFx or /FS1 max. 50m / 165ft);
the following lengths can be ordered (e.g. 3m = L003):
RCCY031-0: 3m, 5m, 10m, 15m, 30m, 50m, 100m, 150m, 200m, 250m, 300m
RCCY031-1: 3m, 5m, 10m, 15m, 30m, 50m
RCCY032-0: 10ft, 15ft, 30ft, 50ft, 100ft, 150ft, 300ft, 500ft, 1000ft
RCCY032-1: 10ft, 15ft, 30ft, 50ft, 100ft, 150ft
RCCY033-0: 3m, 5m, 10m, 15m, 30m, 50m, 100m, 150m, 300m
RCCY033-1: 3m, 5m, 10m, 15m, 30m, 50m
RCCY034-0: 10ft, 15ft, 30ft, 50ft, 100ft, 150ft, 300ft, 500ft, 1000ft
RCCY034-1: 10ft, 15ft, 30ft, 50ft, 100ft, 150ft
Options:
Hazardous area installation
Termination kits
Quick delivery
/KS1
/TKxx
/QD
Blue cable for Ex-i indication
Quantity of additional termination kits
Delivery within 24 hours from factory
xx = 01 to 99
only RCCY031-1, L003, L005, L010
Remote rack-mount Converter RCCR31, Model, Suffix and Option Code
Code
RCCR31 Remote converter for 19 rack mounting to be connected to RCCS3
Power supply -A
-D
90 - 264 V AC
24 V DC
Hazardous Area Approvals
1)
/KS1
/FS1
/ES1
/US1
/NS1
ATEX associated apparatus for intrinsic safe detector connection for gas group IIC
FM associated apparatus for intrinsic safe detector output
IECEx associated apparatus for intrinsic safe detector output for gas group IIC
INMETRO associated apparatus for intrinsic safe detector output for gas group IIC
NEPSI associated apparatus for intrinsic safe detector output for gas group IIC
with /HP not for gas groups A and B
GOST
1)
/QR1
/QR2
see page 9
see page 9
High Driving Power /HP High Driving Power not for combination with RCCS30LR to 34, recom-
mended for combination with RCCS36 to 39, strongly
recommended for combination with RCCS39/IR,
mandatory for combination with RCCS39/XR
4)
Active Pulse Output /AP One active pulse output not with /NM
NAMUR Switch /NM One pulse output acc. EN 60947-5-6 (NAMUR) not with /AP
Communication /MB1 Modbus communication protocol for selected parameters and values
HART

Gas Measurement /GA Gas measurement, special factory adjustments and settings select affiliated RCCS3 with /GA
Combination with RCCS39/XR /XR Special converter adjustment with RCCS39/XR mandatory for combination with RCCS39/XR
No Combination /NC No combination with detector
2)
/CST
/Cxx
Measurement Options
not with /GA
not with /GA
Subrack /SR2
/SR4
Subrack for 2 converter RCCR31 with mounting
Subrack for 4 converter RCCR31 with mounting
/IDn
/IFn
3)
3)
3)
1)
Select affiliated RCCS3 with the same approval type (e.g. /KS1 with /KS1).
2)
For detailed information please see TI 01R04B04-04E-E. Option /K6 of RCCS3 is recommended with concentration measurement.
3)
4)
RCCR31 in combination with RCCS39/XR with gas application /GA can also be ordered without /HP.
28
Advanced Concentration Measurement Options (others on request), recommended with Option /K6
Option Display Components Concentration
range
Temp.
range
Source of concentration- / density table
/C01 Brix Sugar / Water 0 - 85 Brix 0 - 80C PTB- Messages 100 5/90:
The density of watery Saccarose solutions after the introduction of the interna-
tional temperature scale of 1990 (ITS1990) Table 5
/C02 WT% NaOH / Water 2 - 50 WT% 0 - 100C DAns-Lax, Handbook for chemists and physicists Vol.1, 3rd edition, 1967
/C03 WT% KOH / Water 0 - 60 WT% 54 - 100C DAns-Lax, Handbook for chemists and physicists Vol.1, 3rd edition, 1967
/C04 WT% NH
4
NO
3
/ Water 1 - 50 WT% 0 - 80C Data table on request
/C05 WT% NH
4
NO
3
/C06
1)
WT% HCl / Water 22 - 34 WT% 20 - 40C DAns-Lax, Handbook for chemists and physicists Vol.1, 3rd edition, 1967
/C07 WT% HNO
3
/C09 WT% H
2
O
2
/C10 WT% Ethylene Glycol /
Water
10 - 50 WT% -20 - 40C Data table on request
/C11 WT% Amylum = starch / Water 33 - 43 WT% 35 - 45C Data table on request
/C12 WT% Methanol / Water 35 - 60 WT% 0 - 40C Data table on request
/C20 VOL% Alcohol / Water 55 - 100 VOL% 10 - 40C Data table on request
/C21 Brix Sugar / Water 40 - 80 Brix 75 - 100C Data table on request
/C30 WT% Alcohol / Water 66 - 100 WT% 15 - 40C Standard Copersucar 1967
/C37 WT% Alcohol / Water 66 - 100 WT% 10 - 40C Brazilian Standard ABNT
/C38 VOL% Alcohol / Water 73 - 100 VOL% 10 - 40C Brazilian Standard ABNT
1)
only with material HC
29
Table 11 : Selection Table Process Connection and Materials, Installation Length (mm)
RCCS
30LR
RCCS
30-33
RCCS34
RCCT34
RCCS36
RCCT36
RCCS38
RCCT38
RCCS39
RCCT39
RCCS39/IR
RCCT39/IR
RCCS39/XR
RCCT39/XR
SH SH SL HC SL HC SL HC SL HC SL HC SL HC
F
l
a
n
g
e
s

a
c
c
o
r
d
i
n
g

t
o

A
S
M
E

B
1
6
.
5
01A1 -150 240 240 370 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
01A2 -300 240 240 370 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
01A3 -600 250 250 380 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
01A5 -900/1500 270 270 400 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
02A1 1-150 ---- 240 370 390 500 ---- ---- ---- ---- ---- ---- ---- ---- ----
02A2 1-300 ---- 240 370 390 500 ---- ---- ---- ---- ---- ---- ---- ---- ----
02A3 1-600 ---- 260 390 ---- 520 ---- ---- ---- ---- ---- ---- ---- ---- ----
02A5 1-9000 ---- 320 450 ---- 540 ---- ---- ---- ---- ---- ---- ---- ---- ----
04A1 1-150 ---- 250 380 390 500 520 600 ---- ---- ---- ---- ---- ---- ----
04A2 1-300 ---- 250 380 390 510 520 600 ---- ---- ---- ---- ---- ---- ----
04A3 1-600 ---- 270 400 ---- 530 ---- 620 ---- ---- ---- ---- ---- ---- ----
04A4 1-900 ---- ---- ---- ---- ---- ---- 640 ---- ---- ---- ---- ---- ---- ----
04A5 1-900/1500 ---- 340 450 ---- 600 ---- ---- ---- ---- ---- ---- ---- ---- ----
05A1 2-150 ---- ---- ---- ---- 510 520 600 620 ---- ---- ---- ---- ---- ----
05A2 2-300 ---- ---- ---- ---- 510 520 600 620 ---- ---- ---- ---- ---- ----
05A3 2-600 ---- ---- ---- ---- 540 ---- 630 ---- ---- ---- ---- ---- ---- ----
05A4 2-900 ---- ---- ---- ---- ---- ---- 720 ---- ---- ---- ---- ---- ---- ----
05A5 2-9000 ---- ---- ---- ---- 660 ---- ---- ---- ---- ---- ---- ---- ---- ----
06A1 2-150 ---- ---- ---- ---- ---- ---- 610 620 ---- ---- ---- ---- ---- ----
06A2 2-300 ---- ---- ---- ---- ---- ---- 610 620 ---- ---- ---- ---- ---- ----
06A3 2-600 ---- ---- ---- ---- ---- ---- 640 ---- ---- ---- ---- ---- ---- ----
06A4 2-900 ---- ---- ---- ---- ---- ---- 760 ---- ---- ---- ---- ---- ---- ----
08A1 3-150 ---- ---- ---- ---- ---- ---- 610 620 1000 1020 ---- ---- ---- ----
08A2 3-300 ---- ---- ---- ---- ---- ---- 620 620 1000 1020 ---- ---- ---- ----
08A3 3-600 ---- ---- ---- ---- ---- ---- 640 ---- 1000 ---- ---- ---- ---- ----
08A4 3-900 ---- ---- ---- ---- ---- ---- 760 ---- ---- ---- ---- ---- ---- ----
10A1 4-150 ---- ---- ---- ---- ---- ---- ---- ---- 1000 1020 1100 ---- ---- ----
10A2 4-300 ---- ---- ---- ---- ---- ---- ---- ---- 1000 1020 1100 ---- ---- ----
10A3 4-600 ---- ---- ---- ---- ---- ---- ---- ---- 1030 ---- 1100 ---- ---- ----
12A1 5-150 ---- ---- ---- ---- ---- ---- ---- ---- 1000 1020 1100 1100 ---- ----
12A2 5-300 ---- ---- ---- ---- ---- ---- ---- ---- 1000 1020 1100 1100 ---- ----
12A3 5-600 ---- ---- ---- ---- ---- ---- ---- ---- 1040 ---- 1160 ---- ---- ----
15A1 6-150 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1100 1100 1350 ----
15A2 6-300 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1100 1100 1350 ----
15A3 6-600 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1200 ---- ---- ----
20A1 8-150 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1350 ----
20A2 8-300 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1350 ----
F
l
a
n
g
e
s

a
c
c
o
r
d
i
n
g

t
o

E
N

1
0
9
2
-
1
01D4 DN 15 PN 40 240 240 370 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
01D6 DN 15 PN 100 250 250 380 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
02D4 DN 25 PN 40 ---- 240 370 390 500 520 ---- ---- ---- ---- ---- ---- ---- ----
02D6 DN 25 PN 100 ---- 260 390 ---- 520 ---- ---- ---- ---- ---- ---- ---- ---- ----
04D4 DN 40 PN 40 ---- 240 370 390 500 520 600 ---- ---- ---- ---- ---- ---- ----
04D6 DN 40 PN 100 ---- 320 450 ---- 560 ---- 620 ---- ---- ---- ---- ---- ---- ----
05D4 DN 50 PN 40 ---- ---- ---- ---- 500 520 600 620 ---- ---- ---- ---- ---- ----
05D5 DN 50 PN 63 ---- ---- ---- ---- 520 ---- 620 620 ---- ---- ---- ---- ---- ----
05D6 DN 50 PN 100 ---- ---- ---- ---- 590 ---- 660 ---- ---- ---- ---- ---- ---- ----
08D4 DN 80 PN 40 ---- ---- ---- ---- ---- ---- 610 620 1000 1020 ---- ---- ---- ----
08D5 DN 80 PN 63 ---- ---- ---- ---- ---- ---- 620 ---- 1000 ---- ---- ---- ---- ----
08D6 DN 80 PN 100 ---- ---- ---- ---- ---- ---- 730 ---- 1000 ---- ---- ---- ---- ----
10D2 DN 100 PN 16 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1100 ---- ---- ----
10D4 DN 100 PN 40 ---- ---- ---- ---- ---- ---- ---- ---- 1000 1020 1100 ---- ---- ----
10D5 DN 100 PN 63 ---- ---- ---- ---- ---- ---- ---- ---- 1000 ---- 1100 ---- ---- ----
10D6 DN 100 PN 100 ---- ---- ---- ---- ---- ---- ---- ---- 1050 ---- 1100 ---- ---- ----
12D2 DN 125 PN 16 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1100 1100 ---- ----
12D4 DN 125 PN 40 ---- ---- ---- ---- ---- ---- ---- ---- 1000 1020 1100 1100 ---- ----
12D5 DN 125 PN 63 ---- ---- ---- ---- ---- ---- ---- ---- 1000 ---- 1100 ---- ---- ----
12D6 DN 125 PN 100 ---- ---- ---- ---- ---- ---- ---- ---- 1100 ---- 1140 ---- ---- ----
15D2 DN 150 PN 16 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1100 1100 1350 ----
15D4 DN 150 PN 40 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1100 1100 1350 ----
15D5 DN 150 PN 63 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1140 ---- ---- ----
15D6 DN 150 PN 100 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1180 ---- ---- ----
20D2 DN 200 PN 16 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1350 ----
20D4 DN 200 PN 40 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1350 ----
30
RCCS
30LR
RCCS
30-33
RCCS34
RCCT34
RCCS36
RCCT36
RCCS38
RCCT38
RCCS39
RCCT39
RCCS39
RCCT39/IR
RCCS39
RCCT39/XR
SH SH SL HC SL HC SL HC SL HC SL HC SL HC
F
l
a
n
g
e
s

a
c
c
o
r
d
i
n
g

t
o

J
I
S

B

2
2
2
0
01J1 DN 15 10K 240 240 370 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
01J2 DN 15 20K 240 240 370 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
02J1 DN 25 10K ---- 240 370 390 500 ---- ---- ---- ---- ---- ---- ---- ---- ----
02J2 DN 25 20K ---- 240 370 390 500 ---- ---- ---- ---- ---- ---- ---- ---- ----
04J1 DN 40 10K ---- 240 370 390 500 520 600 ---- ---- ---- ---- ---- ---- ----
04J2 DN 40 20K ---- 240 370 390 500 520 600 ---- ---- ---- ---- ---- ---- ----
05J1 DN 50 10K ---- ---- ---- ---- 500 520 600 620 ---- ---- ---- ---- ---- ----
05J2 DN 50 20K ---- ---- ---- ---- 500 520 600 620 ---- ---- ---- ---- ---- ----
08J1 DN 80 10K ---- ---- ---- ---- ---- ---- 600 620 1000 1020 ---- ---- ---- ----
08J2 DN 80 20K ---- ---- ---- ---- ---- ---- 610 620 1000 1020 ---- ---- ---- ----
10J1 DN 100 10K ---- ---- ---- ---- ---- ---- ---- ---- 1000 1020 1100 ---- ---- ----
10J2 DN 100 20K ---- ---- ---- ---- ---- ---- ---- ---- 1000 1020 1100 ---- ---- ----
12J1 DN 125 10K ---- ---- ---- ---- ---- ---- ---- ---- 1000 1020 1100 1100 ---- ----
12J2 DN 125 20K ---- ---- ---- ---- ---- ---- ---- ---- 1000 1020 1100 1100 ---- ----
15J1 DN 150 10K ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1100 1100 ---- ----
15J2 DN 150 20K ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 1100 1100 ---- ----
C
l
a
m
p

D
I
N
01S4 DN 15 240 240 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
02S4 DN 25 ---- 240 370 *) ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
04S4 DN 40 ---- 240 370 ---- 500 *) ---- ---- ---- ---- ---- ---- ---- ---- ----
05S4 DN 50 ---- ---- ---- ---- 500 ---- 600 *) ---- ---- ---- ---- ---- ---- ----
06S4 DN 65 ---- ---- ---- ---- ---- ---- 600 ---- ---- ---- ---- ---- ---- ----
10S4 DN 100 ---- ---- ---- ---- ---- ---- ---- ---- 1000 ---- ---- ---- ---- ----
T
r
i
-
C
l
a
m
p
01S8 240 240 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
02S8 1 ---- 240 370 *) ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
04S8 1 ---- 240 370 ---- 500 *) ---- ---- ---- ---- ---- ---- ---- ---- ----
05S8 2 ---- ---- ---- ---- 500 ---- 600 *) ---- ---- ---- ---- ---- ---- ----
08S8 3 ---- ---- ---- ---- ---- ---- 600 ---- ---- ---- ---- ---- ---- ----
10S8 4 ---- ---- ---- ---- ---- ---- ---- ---- 1000 ---- ---- ---- ---- ----
D
I
N
1
1
8
5
102S2 DN 25 ---- 240 370 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
04S2 DN 40 ---- ---- ---- ---- 500 ---- ---- ---- ---- ---- ---- ---- ---- ----
05S2 DN 50 ---- ---- ---- ---- ---- ---- 600 ---- ---- ---- ---- ---- ---- ----
10S2 DN 100 ---- ---- ---- ---- ---- ---- ---- ---- 1000 ---- ---- ---- ---- ----
T
h
r
e
a
d
41G9 G female 260 260 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
01G9 G female 260 260 390 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
23G9 G female 260 260 390 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
41T9 NPT female 260 260 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
01T9 NPT female 260 260 390 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
23T9 NPT female 260 260 390 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
*) not possible with Option SFx, SA, SE
Table 11 : Selection Table Process Connection and Materials, Installation Length (continued)
Subject to change without notice
REGISTERED TRADEMARKS
HART
: Registered trademark of HART Communication Foundation, Austin, TX, USA

MODBUS
: Registered trademark of MODBUS Organization

FOUNDATION Fieldbus : Registered trademark of the Fieldbus FOUNDATION, Austin, TX, USA
TRI-CLAMP
: Registered trademark of Ladish & Co., Inc., Kenosha, USA

31
32
Yokogawa has an extensive sales and
distribution network.
Please refer to the European website
(www.yokogawa.com/eu) to contact your
nearest representative.
Euroweg 2
3825 HD AMERSFOORT
The Netherlands
www.yokogawa.com/eu
YOKOGAWA ELECTRIC CORPORATION
World Headquarters
9-32, Nakacho 2-chome, Musashino-shi
Tokyo 180-8750
Japan
www.yokogawa.com
YOKOGAWA CORPORATION OF AMERICA
2 Dart Road
Newnan GA 30265
USA
www.yokogawa.com/us
YOKOGAWA ELECTRIC ASIA Pte. LTD.
5 Bedok South Road
Singapore 469270
Singapore
www.yokogawa.com/sg
YOKOGAWA CHINA CO. LTD.
3F Tower D Cartelo Crocodile Building
No.568 West Tianshan Road Changing District
Shanghai, China
www.yokogawa.com/cn
YOKOGAWA MIDDLE EAST B.S.C.(c)
P.O. Box 10070, Manama
Building 577, Road 2516, Busaiteen 225
Muharraq, Bahrain
www.yokogawa.com/bh

Yokogawa

Uploaded by

Copyright:

Available Formats

Yokogawa

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Yokogawa

Uploaded by

Copyright:

Available Formats

GS 01R4B04-00E-E

communication protocol rev. 5, superimposed on

communication. For comfortable

communication or with status

communication in converter 8 digits for tag, 22 digits for long tag

communication in converter 8 digits for tag, 22 digits for long tag

communication in converter 8 digits for tag, 22 digits for long tag

: Registered trademark of HART Communication Foundation, Austin, TX, USA

: Registered trademark of MODBUS Organization

: Registered trademark of Ladish & Co., Inc., Kenosha, USA

You might also like