Pioneer vsx-1016
Pioneer vsx-1016
Pioneer vsx-1016
RECEIVER
VSX-1014-S
VSX-2014i-G
Operating Instructions
VSX_2014TX.book.fm 1
D3-4-2-1-1_En-A
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
WARNING
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230V
or 120V) written on the rear panel. D3-4-2-1-4_A_En
Before plugging in for the first time, read the following
section carefully.
WARNING
To prevent a fire hazard, do not place any naked
flame sources (such as a lighted candle) on the
equipment. D3-4-2-1-7a_A_En
WARNING
This equipment is not waterproof. To prevent a fire
or shock hazard, do not place any container filled
with liquid near this equipment (such as a vase or
flower pot) or expose it to dripping, splashing, rain
or moisture. D3-4-2-1-3_A_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat
radiation (at least 60 cm at top, 10 cm at rear, and
30 cm at each side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the
product, and to protect it from overheating. To
prevent fire hazard, the openings should never be
blocked or covered with items (such as newspapers,
table-cloths, curtains) or by operating the
equipment on thick carpet or a bed. D3-4-2-1-7b_A_En
Operating Environment
Operating environment temperature and humidity:
+5 C +35 C (+41 F +95 F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light) D3-4-2-1-7c_A_En
When disposing of used batteries, please comply
with governmental regulations or
environmental public instructions rules that
apply in your country/area. D3-4-2-3-1_En
Thank you for buying this Pioneer product.
Please read through these operating
instructions so you will know how to operate
your model properly. After you have finished
reading the instructions, put them away in a
safe place for future reference.
MASTER VOLUME
DVD/LD TV/SAT DVR/VCR VIDEO1
CD CD-R/ TAPE/MD TUNER VIDEO2
VSX-52TX
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
VSX_2014TX.book.fm 2
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from
the AC outlet to shut down all power. Therefore,
make sure the unit has been installed so that the
power cord can be easily unplugged from the AC
outlet in case of an accident. To avoid fire hazard,
the power cord should also be unplugged from the
AC outlet when left unused for a long period of time
(for example, when on vacation).
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left
unused for a long period of time (for example, when
on vacation). D3-4-2-2-1a_A_En
TWO VOLTAGE SELECTORS
230-
240 V
120-127V 110V
220V
220V
230-240V
110V
120- 127V
Voltage selector
You can find the voltage selector switch on the rear
panel of multi-voltage models.
The factory setting for the voltage selector is 220V.
Please set it to the correct voltage for your country
or region.
Saudi Arabia operates on 127V and 220V mains
voltage. Please set to the correct voltage before using.
For Taiwan, please set to 110V before using.
For Mexico, please set to 120-127V before using.
Before changing the voltage, disconnect the AC power
cord. Use a medium size screwdriver to change the
voltage selector switch.
D3-4-2-1-5_En
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. D8-10-1-2_En
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the users right to operate
the equipment. D8-10-2_En
CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the
unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and
televisions, use shielded cables and connectors for connections. D8-10-3a_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which
requires repair will be charged for even during the
warranty period. K041_En
VSX_2014TX.book.fm 3
4
En
Contents
01 Before you start
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Checking whats in the box. . . . . . . . . . . . . . . . . . . . . . . 6
Installing the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . 7
Loading the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operating range of remote control unit . . . . . . . . . . . 7
02 5 minute guide
Introduction to home theater . . . . . . . . . . . . . . . . . . . . . 8
Listening to Surround Sound . . . . . . . . . . . . . . . . . . . . . 8
Automatically setting up for surround sound
(MCACC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Other problems when using the Auto MCACC
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Checking the settings on your DVD (or other)
player. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Playing a source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
03 Connecting up
About cable types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Analog audio cables . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Digital audio cables . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Video cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
When making cable connections . . . . . . . . . . . . . . . 15
About the RS-232C connector . . . . . . . . . . . . . . . . . . . 15
About the video converter . . . . . . . . . . . . . . . . . . . . . . . 15
Connecting digital audio components. . . . . . . . . . . . . 16
Connecting analog audio components . . . . . . . . . . . . 17
Connecting multichannel analog components . . . . . 17
Connecting video components. . . . . . . . . . . . . . . . . . . 18
Connecting to the front panel video terminal . . . . . . 18
Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
AM loop antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using an external antenna to improve FM
reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting the speakers . . . . . . . . . . . . . . . . . . . . . . . 21
Speaker terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Hints on speaker placement . . . . . . . . . . . . . . . . . . . 22
AC power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Operating other Pioneer components . . . . . . . . . . . . . 23
04 Controls and displays
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
05 Listening to your system
Auto playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Listening in surround sound . . . . . . . . . . . . . . . . . . . . 30
Standard surround sound . . . . . . . . . . . . . . . . . . . . . 30
Using the Home THX modes. . . . . . . . . . . . . . . . . . . 31
Using the Advanced surround effects . . . . . . . . . . . 31
Dolby Pro Logic IIx Music settings . . . . . . . . . . . . . . 32
Neo:6 Music settings . . . . . . . . . . . . . . . . . . . . . . . . . 32
Listening in stereo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Listening with Acoustic Calibration EQ . . . . . . . . . . . 33
Choosing the input signal . . . . . . . . . . . . . . . . . . . . . . 33
Using the surround back channel
(Extended mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Using the Virtual Surround Back mode
(VirtualSB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Using Loudness and Midnight listening. . . . . . . . . . . 36
Enhancing dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Using the tone controls . . . . . . . . . . . . . . . . . . . . . . . . 36
Playing other sources. . . . . . . . . . . . . . . . . . . . . . . . . . 37
Selecting the multichannel analog inputs . . . . . . . . . 37
Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . 37
06 The System Setup menu
Making receiver settings from the System Setup
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Surround back speaker setting . . . . . . . . . . . . . . . . . . 38
Manual MCACC speaker setup . . . . . . . . . . . . . . . . . . 39
Fine Channel Level . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Fine Channel Distance. . . . . . . . . . . . . . . . . . . . . . . . 40
Acoustic Calibration EQ. . . . . . . . . . . . . . . . . . . . . . . 41
Manual speaker setup . . . . . . . . . . . . . . . . . . . . . . . . . 43
Speaker Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Crossover Network . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Channel Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Speaker Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
07 Using the tuner
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Improving FM stereo sound. . . . . . . . . . . . . . . . . . . . 47
Tuning directly to a station . . . . . . . . . . . . . . . . . . . . 47
Saving station presets . . . . . . . . . . . . . . . . . . . . . . . . . 48
Naming station presets . . . . . . . . . . . . . . . . . . . . . . . 48
Listening to station presets . . . . . . . . . . . . . . . . . . . . 48
08 Making recordings
Making an audio or a video recording . . . . . . . . . . . . 49
VSX_2014TX.book.fm 4
5
En
09 Controlling the rest of your system
Setting the remote to control other components . . . . 50
Selecting preset codes directly . . . . . . . . . . . . . . . . . . 50
Programming signals from other remote controls. . . 51
Erasing one of the remote control button settings. . . 52
Erasing all of the remote control presets . . . . . . . . . . 52
Direct function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Confirming preset codes. . . . . . . . . . . . . . . . . . . . . . . . 52
Controls for TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Controls for other components . . . . . . . . . . . . . . . . . . 54
10 Other connections
Second Zone speaker B setup . . . . . . . . . . . . . . . . . . . 55
Switching the speaker system. . . . . . . . . . . . . . . . . . 55
Bi-amping your front speakers . . . . . . . . . . . . . . . . . . . 56
Bi-wiring your speakers. . . . . . . . . . . . . . . . . . . . . . . . . 56
Connecting additional amplifiers. . . . . . . . . . . . . . . . . 57
Multi-room listening . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Making multi-room connections . . . . . . . . . . . . . . . . 57
Using the sub room controls . . . . . . . . . . . . . . . . . . . 58
Using the i.LINK interface. . . . . . . . . . . . . . . . . . . . . . . 59
About i.LINK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
About PQLS rate control . . . . . . . . . . . . . . . . . . . . . . 60
Creating an i.LINK network . . . . . . . . . . . . . . . . . . . . 60
Switching components on and off using the
12 volt trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Using this receiver with a Pioneer plasma display. . . 61
Using the SR+ mode with a Pioneer plasma
display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
11 Other Settings
The Input Assign menu . . . . . . . . . . . . . . . . . . . . . . . . 63
The Other Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . 65
Dynamic Range Control Setup . . . . . . . . . . . . . . . . . 66
Dual Mono Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
LFE Attenuator Setup. . . . . . . . . . . . . . . . . . . . . . . . . 66
SR+ Setup for Pioneer plasma displays . . . . . . . . . 67
Multi Room Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
12 Volt Trigger Setup . . . . . . . . . . . . . . . . . . . . . . . . . 68
SACD Gain Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
12 Additional information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
No sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Other audio problems . . . . . . . . . . . . . . . . . . . . . . . . 71
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
i.LINK interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
i.LINK messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Resetting the main unit . . . . . . . . . . . . . . . . . . . . . . . . 76
Changing the frequency step. . . . . . . . . . . . . . . . . . . . 76
Switching the speaker impedance . . . . . . . . . . . . . . . 76
Changing the TV format setting. . . . . . . . . . . . . . . . . . 76
Surround sound formats . . . . . . . . . . . . . . . . . . . . . . . 77
Dolby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
About THX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Cleaning the unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
VSX_2014TX.book.fm 5
Before you start 01
6
En
Chapter 1:
Before you start
Features
High quality MOSFET design
This receiver offers high-quality discrete MOSFET
configuration unique to Pioneer for low distortion, and
generates equal amplifier power to all channels,
eliminating the possibility of one channel dominating a
particular sound field.
Easy setup using Multichannel Acoustic
Calibration (MCACC)
Setting up for home theater sound is as easy as
connecting your speakers, a DVD player or other source,
and your TV. The Auto Surround Setup provides a quick
but accurate surround sound setup, while for complete
surround sound control you still have access to the full
range of surround sound settings.
THX Select certified design
This receiver bears the THX Select logo, which means it
has passed a rigorous series of quality and performance
tests covering every aspect of the product. This includes
testing of pre-amplifier and power amplifier performance
and operation, and hundreds of other parameters in both
the digital and analog domain, making your home
theater experience as faithful as possible to what the
director intended.
Dolby Digital and DTS decoding, including Dolby
Digital EX, Dolby Pro Logic IIx, DTS 96/24 and DTS-ES
Dolby Digital and DTS decoding brings theater sound
right into your home with up to six channels of surround
sound, including a special LFE (Low Frequency Effects)
channel for deep, realistic sound effects.
The built-in Dolby Pro Logic IIx and DTS Neo:6 decoders
not only provide full surround sound decoding for Dolby
Surround sources, but will also generate convincing
surround sound for any stereo source.
Also, with the addition of a surround back speaker, you
can take advantage of the built-in Dolby Digital EX and
DTS-ES decoders for six-channel surround sound.
Easy-to-use LCD remote control
The remote control gives you not only complete control
over every function of this receiver, but also over the main
functions for other components in your home theater
system. Using a system of preset codes, you can
program the remote to operate a wide range of other
equipment.
VSX-2014i-G model only:
i.LINK
digital interface
The i.LINK interface makes it possible to connect this
receiver to i.LINK-equipped components, allowing you to
enjoy high sampling rate (up to 192kHz) PCM
multichannel digital audio from DVD-Audio and SACD
discs, as well as digital audio from DVD-Video, CD and
Video CD discs, all with a single cable.
Seamless video conversion
With the Pioneer video converter, you can use a wide
range of cables interchangeably, giving you more
flexibility when making video connections.
Checking whats in the box
Please check that you've received the following supplied
accessories:
Setup microphone and stand
Remote control unit
AA/LR6 dry cell batteries x2
AM loop antenna
FM wire antenna
+10
IN
PU
T ATT
FL DIM
M
ER
SR
DISC
R
E
C
E
IV
E
R
M
U
LTI C
O
N
TR
O
L
S
O
U
R
C
E
IN
P
U
T
S
E
L
E
C
T EN
TER
T
V
C
O
N
TR
O
L
R
EC
EIV
ER
C
O
N
T
R
O
L
SH
IFT
V
O
L
D
V
D
/LD
TV
/SAT
D
VR/VCR
TV CO
N
T
CD
TUNE
TUNE
ST
ST
THX
SLEEP
DIALO
G E
AUTO SURR
STANDARD
ADV.SURR
STEREO
IN
PU
T
SELECT
TV
CH
D
TV O
N
/O
FF
TUNER
DISPLAY
M
PX
AUDIO
CH RETURN
SUBTITLE
M
IDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CH SEL
ACOUSTIC
EQ
D
TV IN
FO
REC
M
U
TE
TV VOL
CD-R/TAPE
TU
N
ER
RECEIVER
ENTER
REC STO
P
HD
D
CH
CHDVD
D
.A
CCESS
TO
P M
EN
U
DTV M
ENU
CLA
SS
M
EN
U
BA
N
D
RETU
RN
G
U
ID
E
T.ED
IT SYSTEM
SETU
P
R
E
C
E
IV
E
R
01_before_you_start.fm 6
Before you start 01
7
En
Antenna adapter
Power cord
Flat-bladed converter plug
These operating instructions
Note
The accessories will be different depending on the
country of purchase. Where two power cords are
included, make sure to use the cord appropriate for
your country or region.
Installing the
receiver
When installing this unit, make sure to put it on a
level and stable surface.
Dont install it on the following places:
on a color TV (the screen may distort)
near a cassette deck (or close to a device that gives off
a magnetic field). This may interfere with the sound.
in direct sunlight
in damp or wet areas
in extremely hot or cold areas
in places where there is vibration or other movement
in places that are very dusty
in places that have hot fumes or oils (such as a kitchen)
Using the remote control
Loading the batteries
Caution
Incorrect use of batteries may result in such hazards as
leakage and bursting. Observe the following precautions:
Never use new and old batteries together.
Insert the plus and minus sides of the batteries
properly according to the marks in the battery case.
Batteries with the same shape may have different
voltages. Do not use different batteries together.
When disposing of used batteries, please comply
with governmental regulations or environmental
public instructions rules that apply in your country or
area.
Operating range of remote control unit
The remote control may not work properly if:
There are obstacles between the remote control and
the receiver's remote sensor.
Direct sunlight or fluorescent light is shining onto the
remote sensor.
The receiver is located near a device that is emitting
infrared rays.
The receiver is operated simultaneously with another
infrared remote control unit.
MASTER VOLUME
DVD/LD TV/SAT DVR/VCR VIDEO1
CD CD-R/ TAPE/MD
STANDBY/ON
MULTI JOG
TUNER
VIDEO2
VSX-52TX
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
) terminals on the receiver match those on the speakers. You can use
speakers with a nominal impedance between 616
(please see
Switching the speaker impedance
on page 76 if you
plan to use speakers with an impedance of less than 8
).
If you only have one surround back speaker, hook it up to the surround back left (
Single
) terminal.
Caution
These speaker terminals carry
HAZARDOUS LIVE
voltage
. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
Make sure that all the bare speaker wire is twisted
together and inserted fully into the speaker terminal.
Use good quality speaker wire to connect the
speakers to the receiver.
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/
SAT
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI-
ROOM &
SOURCE
AUDIO
VIDEO S-VIDEO
RS - 232C
IN
IN
OUT
OUT
OUT
ANTENNA
AM LOOP
FMUNBAL 75
MONITOR OUT
12V
TRIGGER
Y
Y
PB
PR
PB
PR
Y
PB
PR
1 2
2
IN 1
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
OUT
REC
IN
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN
(DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN OUT
DIGITAL (TV/SAT)
4
3
2 1
1 4
SPEAKERS
AC IN TWOVOLTAGE SELECTORS
230-240 V
120-127V 110V
A B R L R L
R L(Single)
FRONT CENTER SURROUND SURROUND BACK /
SELECTABLE
SELECTABLE
220V
220V
230-240V
110V
120- 127V
OUT
OUT
D-R/
APE/MD
DEO1
VR /
CR
PRE
OUT
CEN-
TER
CEN-
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
SUBW.
M
R L
R L
R L
R
L
LAY
LAY
REC
INPUT
Front speakers
L R C LS RS
Powered
subwoofer
SW
Surround speakers
SBL SBR
Surround back speakers Center speaker
VSX_2014TX.book.fm 9
5 minute guide 02
10
En
Make sure that the speaker cable youre going to use is
properly prepared with about 10 mm of insulator stripped
from each wire, and the exposed wire strands twisted
together (
fig. A
).
To connect a terminal, unscrew the terminal a few turns
until there is enough space to insert the exposed wire
(
fig. B
). Once the wire is in position, tighten the terminal
until the wire is firmly clamped (
fig. C
).
Where you place the speakers will have a big effect on the
sound. Place your speakers as shown below for the best
surround sound effect. See
Hints on speaker placement
on page 22 for more on this.
4 Plug in the receiver and switch it on, followed by
your DVD player, your subwoofer and the TV.
Make sure youve set the video input on your TV to this
receiver. Check the manual that came with the TV if you
dont know how to do this.
5 Use the on-screen automatic MCACC setup to set
up your system.
See
Automatically setting up for surround sound
(MCACC)
on the next page for more on this.
6 Play a DVD, and adjust the volume to your liking.
Make sure that
DVD/LD
is showing in the receivers
display, indicating that the DVD input is selected. If it
isnt, press
DVD/LD
on the remote control to set the
receiver to the DVD input.
In addition to the basic playback explained in
Playing a
source
on page 13, there are several other sound options
you can select. See
Listening to your system
on page 30
for more on this. See also
Making receiver settings from
the System Setup menu
on page 38 for more setup
options.
If youre not familiar with the proper DVD settings,
refer to
Checking the settings on your DVD (or other)
player
on page 13.
10mm
fig. A fig. B fig. C
Front
speaker
(L)
Surround
speaker (LS)
Surround
speaker (RS)
Surround back
speaker (SBL)
Surround
back
speaker (SBR)
Center
speaker
(C)
Subwoofer (SW)
Listening
position
Front
speaker
(R)
VSX_2014TX.book.fm 10
5 minute guide 02
11
En
Automatically setting up for
surround sound (MCACC)
The Auto MCACC Setup measures the acoustic
characteristics of your listening area, taking into account
ambient noise, speaker size and distance, and tests for
both channel delay and channel level. After you have set
up the microphone provided with your system, the
receiver uses the information from a series of test tones
to optimize the speaker settings and equalization for your
particular room.
Make sure you do this before moving on to
Playing a
source
on page 13.
Important
Make sure the microphone and speakers are not
moved during the Auto MCACC Setup.
Using the Auto MCACC Setup will overwrite any
existing speaker settings in the receiver.
Before using the Auto MCACC Setup the
headphones should be disconnected and
MULTI CH
IN
switched off.
The receiver will automatically exit the current screen
after three minutes of inactivity.
Caution
The test tones used in the Auto MCACC Setup are
output at high volume.
1 Switch on the receiver and your TV.
2 Connect the microphone to the MCACC SETUP
MIC jack on the front panel.
Make sure there are no obstacles between the speakers
and the microphone.
Note that the illustration above shows the VSX-2014i-G
however, connection for the VSX-1014-S is the same.
Place the microphone on the supplied microphone
stand (shown above) for the best results with the
Auto MCACC Setup.
If you have a tripod, use it to place the microphone so that
its about ear level at your normal listening position.
Otherwise, place the microphone at ear level using a
table or a chair.
3 Press RECEIVER on the remote control, then press
the SYSTEM SETUP button.
An on-screen display (OSD) appears on your TV. Use the
///
buttons and
ENTER
on the remote control to
navigate through the screens and select menu items.
Press
RETURN
to exit the current menu.
Press
SYSTEM SETUP
at any time to exit the System
Setup menu.
VSX-1014-S only
If you find picture distortion, or the
OSD doesnt appear, see
Changing the TV format
setting
on page 76 and make sure the setting is
correct for your country or region.
4 Select AUTO MCACC from the System Setup
menu then press ENTER.
5 Make sure Normal (SB) is selected then press
ENTER.
+10
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
ENTER
TV CONTROL
VOL
DVD/LD TV/SAT DVR/VCR TVCONT
CD
ST ST
INPUT
SELECT
TV CH TVVOL
CD-R/TAPE TUNER RECEIVER
ENTER
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
TUNE
TUNE
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
i.LINK
SELECT
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
MULTI
JOG
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
i.LINK
SELECT
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
MULTI
JOG
System Setup
[ 1. Surr Back System ]
[ 2. AUTO MCACC ]
[ 3. MANUAL MCACC ]
[ 4. Manual SP Setup ]
[ 5. Input Assign ]
[ 6. Other Setup ]
Enter : Select
Return : Exit
2. AUTO MCACC
Surround Back Output
[ Normal (SB) ]
Enter : Start
Return : Cancel
VSX_2014TX.book.fm 11
5 minute guide 02
12
En
If you are planning on bi-amping your front speakers,
or setting up a separate speaker system in another
room, read through
Surround back speaker setting
on
page 38 and make sure to connect your speakers as
necessary before continuing to step 6.
6 Follow the instructions on-screen.
Make sure the microphone is connected.
If youre using a subwoofer, it is automatically
detected every time you switch on the system. Make
sure it is on and the volume is turned up.
See below for notes regarding high background
noise levels and other possible interference.
7 Wait for the Auto MCACC Setup to finish
outputting test tones.
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
its doing this.
Do not adjust the volume during the test tones. This
may result in incorrect speaker settings.
8 Confirm the speaker configuration in the OSD.
The configuration shown on-screen should reflect the
actual speakers you have.
If the speaker configuration displayed isnt correct, use
the
/
(cursor up/down) buttons to select the speaker
and
/
(cursor left/right) to change the setting (and
number for surround back). When youre finished, go to
the next step.
If you see an error message (
ERR
) in the right side
column, there may be a problem with the speaker
connection. If selecting
RETRY
doesnt fix the problem,
turn off the power and check the speaker connections.
9 Make sure OK is selected, then press ENTER.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for channel level, speaker
distance, and Acoustic Calibration EQ.
Again, try to be as quiet as possible while this is
happening. It may take 38 minutes.
10 The Auto MCACC Setup has finished! Select
Skip to go back to the System Setup menu.
The MCACC indicator on the front panel will light to show
the surround settings are complete.
The settings made in the Auto MCACC Setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using the
System Setup menu (see page 38).
If you are using THX Certified speakers, confirm that
all speakers are set to
SMALL
in
Speaker Setting
on
page 44, and that the
Crossover Network
on page 45
is set to
80Hz
.
You can also choose to view the settings by selecting
individual parameters from the
Analyzed Data Check
screen:
Speaker Setting
The size and number of speakers
youve connected (see page 44 for more on this)
Speaker Distance
The distance of your speakers
from the listening position (see page 46 for more on
this)
Channel Level
The overall balance of your speaker
system (see page 45 for more on this)
Acoustic Cal EQ
Adjustments to the frequency
balance of your speaker system based on the
acoustic characteristics of your room (see page 41
for more on this)
2. AUTO MCACC
Set microphone
Turn on Sub Woofer
Return : Cancel
2. AUTO MCACC
Please wait
Caution!!
Test tone is
output loudly.
Return:Cancel
2. AUTO MCACC
Now Analyzing
Environment Check
Ambient Noise [ ]
Microphone [ ]
Speaker YES/NO [ ]
Return:Cancel
2. AUTO MCACC
Check!!!
Front [ YES ]
Center [ YES ]
Surround [ YES ]
Surr Back [ YES X 2]
Sub Woofer [ YES ]
[ OK ]
2. AUTO MCACC
Now Analyzing
Surround Analyzing
Speaker System [ ]
Speaker Distance [ ]
Channel Level [ ]
Acoustic Cal EQ [ ]
Return:Cancel
2. AUTO MCACC
Analyzed Data Check
[a.Speaker Setting ]
[b.Speaker Distance ]
[c.Channel Level ]
[d.Acoustic Cal EQ ]
[ Skip ]
VSX_2014TX.book.fm 12
5 minute guide 02
13
En
Press
RETURN
after you have finished checking each
screen. When youre finished, select
Skip
to go back to
the System Setup menu.
Note
If you leave an error message on the screen for over
three minutes, or if you cancel the Auto MCACC
Setup at any time, the receiver automatically exits
and no settings will be made.
Depending on the characteristics of your room,
sometimes identical speakers with cone sizes of
around 12cm will end up with different size settings.
You can correct the setting manually using the
Manual speaker setup
on page 43.
The subwoofer distance setting may be farther than
the actual distance from the listening position. This
setting should be accurate (taking delay and room
characteristics into account) and generally does not
need to be changed.
Remember to disconnect the microphone after
youve finished the Auto MCACC Setup.
Other problems when using the Auto MCACC
Setup
If the room environment is not optimal for the Auto
MCACC Setup (too much background noise, echo off the
walls, obstacles blocking the speakers from the
microphone) the final settings may be incorrect. Check
for household appliances (air conditioner, fridge, fan,
etc.), that may be affecting the environment and switch
them off if necessary. If there are any instructions
showing in the front panel display, please follow them.
Some older TVs may interfere with the operation of
the microphone. If this seems to be happening,
switch off the TV when doing the Auto MCACC Setup.
Checking the settings on your DVD
(or other) player
Before continuing, you may want to check the digital
audio output settings on your DVD player and digital
satellite receiver.
Check that your DVD player/satellite receiver is
set to output Dolby Digital, DTS and 88.2/96kHz PCM
(2 channel) audio.
If there is an option for MPEG audio, set this to convert
the MPEG audio to PCM.
If you connected the multichannel analog outputs of the
player to this receiver, make sure that the player is set to
output multichannel analog audio.
Note
Depending on your DVD player or source discs, you
may only get digital 2 channel stereo and analog
sound. In this case, the receiver must be set to a
multichannel listening mode (see
Listening in
surround sound
on page 30 if you need to do this) if
you want multichannel surround sound.
Playing a source
Here are the basic instructions for playing a source (such
as a DVD disc) with your home theater system.
1 Turn on the power of the playback component
(for example a DVD player), your TV and subwoofer
(if you have one).
If your source is the TVs built-in tuner, then switch to
the channel you want to watch, otherwise make sure
that the TVs video input is set to this receiver. (For
example, if you connected this receiver to the
VIDEO
1
jacks on your TV, make sure that the
VIDEO 1
input
is now selected.)
2 If the receiver isnt already on, press
RECEIVER
to switch it on.
3 Change the receiver input to the source you
want to play.
You can use the front panel input select buttons or the
dedicated
MULTI CONTROL
buttons on the remote
control.
4 Press AUTO SURR (remote control) and start
playback of the DVD (or other component).
If youre playing a Dolby Digital or DTS surround sound
DVD disc, you should hear surround sound. If you are
playing a stereo source, you will only hear sound from the
front left/right speakers in the default listening mode.
See also
Listening to your system
on page 30 for
more information on different ways of listening to
sources.
5 Use the volume control (front panel or remote)
to adjust the volume level.
Turn down the volume of your TV so that all the sound
is coming from the speakers connected to this
receiver.
0dB
is the volume level of a regular movie theater.
Adjust the volume to your liking between
80dB
(min) and
+12dB
(max).
Note
If you need to manually switch the input signal type
from digital to analog (stereo or multichannel), press
SIGNAL SELECT
(page 33).
For more detailed surround sound setup, see
The
System Setup menu
on page 38.
VSX_2014TX.book.fm 13
Connecting up 03
14
En
Chapter 3:
Connecting up
Important
Before making or changing any connections, switch
off the power and disconnect the power cord from the
AC outlet.
About cable types
Analog audio cables
Use stereo RCA phono cables to connect analog audio
components. These cables are typically red and white,
and you should connect the red plugs to R (right)
terminals and white plugs to L (left) terminals.
Digital audio cables
Commercially available coaxial digital audio cables or
optical cables should be used to connect digital
components to this receiver.
When connecting optical cables, be careful when
inserting the plug not to damage the shutter
protecting the optical socket.
When storing optical cable, coil loosely. The cable
may be damaged if bent around sharp corners.
You can also use a standard RCA video cable for
coaxial digital connections.
Video cables
Standard RCA video cables
These cables are the most common type of video
connection and should be used to connect to the
composite video terminals. They have yellow plugs to
distinguish them from cables for audio.
S-video cables
S-video cables give you clearer picture reproduction than
standard RCA video cables by sending separate signals
for the luminance and color.
Component video cables
Use component video cables to get the best possible
color reproduction of your video source. The color signal
of the TV is divided into the luminance (
Y
) signal and the
color (
P
B
and
P
R
) signals and then output. In this way,
interference between the signals is avoided.
Right (red)
Analog audio cables
Left (white)
Coaxial digital audio cable Optical cable
Standard RCA video cable
S Video
Green (Y)
Blue (PB)
Red (PR)
Component video cables
03_connecting_up.fm 14
Connecting up 03
15
En
When making cable connections
Be careful not to arrange cables in a manner that bends
the cables over the top or around this unit. If the cables
are laid on top of the unit, the magnetic field produced by
the transformers in this unit may cause a humming noise
to come from the speakers.
About the RS-232C connector
VSX-2014i-G model only
The RS-232C connector on the rear panel is for future
improvements.
About the video converter
VSX-2014i-G model only
The video converter allows you to connect various video
sources using composite, S-video or component video
connections and the signal will be output through all of
the
MONITOR OUT
jacks (excluding multi-room). The
only exception is component video input, which is only
output from the component video output. Therefore, if
you want to connect any source using component video,
you must also connect your TV using component video. If
several video components are connected to the same
input function, the converter gives priority to component,
S-video, then composite (in that order).
The following chart shows when the video signal will be
converted fro
m the vari
ous video inputs (left column) for
output to the
MONITOR OUT
jacks (top row):
The
mark above indicates that the component
video input must be assigned before it will be output
(see
Assigning the component video inputs
on
page 64 for more on this).
When recording video sources however, you wont be
able to record sources connected to the component
video inputs. With composite and S-video sources,
they must be connected using the same type of video
cable as you used to connect the recorder to the
receiver.
NTSC model
This feature is available with NTSC
signals only. For a PAL signal, make sure youve used
the same type of cable for your video component and
monitor connections.
PAL model
With NTSC sources, you will only be able
to convert from S-Video to component video, and not
vice-versa.
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/
SAT
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI-
ROOM &
SOURCE
AUDIO
VIDEO S-VIDEO
RS - 232C
IN
IN
OUT
OUT
OUT
ANTENNA
AM LOOP
FMUNBAL 75
MONITOR OUT
12V
TRIGGER
Y
Y
PB
PR
PB
PR
Y
PB
PR
1 2
2
IN 1
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
OUT
REC
IN
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN
(DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN OUT
DIGITAL (TV/SAT)
4
3
2 1
1 4
A R L
FRONT C
Video
terminal
MONITOR OUT
VIDEO
(Composite)
S-VIDEO
COMPONENT
VIDEO
VIDEO IN
(Composite)
S-VIDEO IN
COMPONENT
VIDEO IN
03_connecting_up.fm 15
Connecting up 03
16
En
Connecting digital audio components
The easiest way to hook up this receiver for surround sound (Dolby Digital and DTS sources) is to use a digital input.
You can do this by either coaxial or optical connections (you do not need to do both). The quality of these two types of
connections is the same but since some digital components only have one type of digital terminal, it is a matter of
matching like with like (for example, the coaxial output from the component to coaxial input on the receiver). This
receiver has four digital inputs (two coaxial inputs and two optical inputs) on the rear panel. Connect your digital
components as shown below.
There is one digital output jack which is marked
DIGITAL OUT
. If you connect this to the optical input on a digital
recorder (for example an MD, DAT or CD-R) you can make direct digital recordings with this unit.
When connecting your equipment, always make sure the power is turned off and the power cord is disconnected from
the AC outlet.
The arrows indicate the direction of the signal.
Note that the illustration above shows the VSX-2014i-G however, connection for the VSX-1014-S is the same.
Note
If your digital connections are different from the default settings, you should refer to
The Input Assign menu
on
page 63 to assign the jacks to the proper component(s).
If you have a have a DVD-Audio or SACD compatible player, see
Connecting multichannel analog components
on
page 17. (
VSX-2014i-G only
Also see
Using the i.LINK interface
on page 59.)
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/
SAT
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO
COMP
AUDIO
VIDEO S-VIDEO
IN
OUT
OUT
OUT
ANTENNA
AM LOOP
FMUNBAL 75
MONITO
Y
Y
PB
PR
PB
PR
Y
PB
PR
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
OUT
REC
IN
VID
ASSIGNABLE
S400
S400
IN
(DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN OUT
DIGITAL (TV/SAT)
4
3
2 1
1 4
OUT
DIGITAL
DIGITAL OUT
COAX
DIGITAL OUT
COAX
DIGITAL
IN
DIGITAL
OUT
CD recorder
Satellite tuner
CD player
DVD or LD player
03_connecting_up.fm 16
Connecting up 03
17
En
Connecting analog audio components
To begin set up, connect your analog audio components (such as a cassette deck) to the jacks. For components you
want to record with, you need to hook up four plugs to the receiver (a set of stereo inputs and a set of stereo outputs),
but for components that only play, you only need to hook up one set of stereo plugs. You must also hook up your digital
components to analog audio jacks if you want to record to/from digital components (like an MD) to/from analog
components. See page 16 for more on digital connections.
When connecting your equipment, always make sure the power is turned off and the power cord is disconnected from
the AC outlet.
The arrows indicate the direction of the audio signal.
Note that the illustration above shows the VSX-2014i-G however, connection for the VSX-1014-S is the same.
Tip
If you dont plan on using the spare audio jacks for video components (for example,
VIDEO1
), you can use these
for connecting another audio component, like a line-level turntable.
Connecting multichannel analog components
If you prefer to use a separate component for decoding multichannel formats such as DVD Audio and SACD, you can
connect a decoder or a DVD player with multichannel analog outputs to the multichannel inputs of this receiver. Note
that the multichannel input can only be used when
MULTI CH IN
is selected (see page 37).
When connecting your equipment, always make sure the power is turned off and the power cord is disconnected from
the AC outlet.
The arrows indicate the direction of the signal.
Note that the illustration above shows the VSX-2014i-G however, connection for the VSX-1014-S is the same.
REC PLAY
L
R
L
R
OUTPUT
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/
SAT
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI-
ROOM &
SOURCE
AUDIO
VIDEO S-VIDEO
RS - 232C
IN
IN
OUT
OUT
OUT
ANTENNA
AM LOOP
FMUNBAL 75
MONITOR OUT
12V
TRIGGER
Y
Y
PB
PR
PB
PR
Y
PB
PR
1 2
2
IN 1
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
OUT
REC
IN
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN
(DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN OUT
DIGITAL
(TV/SAT)
4
3
2 1
1 4
SPE
A
CD player
CD-R/Tape/MD deck
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/
SAT
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI-
ROOM &
SOURCE
AUDIO
VIDEO S-VIDEO
RS - 232C
IN
IN
OUT
OUT
OUT
ANTENNA
AM LOOP
FMUNBAL 75
MONITOR OUT
12V
TRIGGER
Y
Y
PB
PR
PB
PR
Y
PB
PR
1 2
2
IN 1
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
OUT
REC
IN
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN
(DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN OUT
DIGITAL (TV/SAT)
4
3
2 1
1 4
SPEAKERS
AC IN TWOVOLTAGE SELECTORS
230-240 V
120-127V 110V
A B R L R L
R L(Single)
FRONT CENTER SURROUND SURROUND BACK /
SELECTABLE
SELECTABLE
220V
220V
230-240V
110V
120- 127V
CENTER
OUTPUT
SUB
WOOFER
OUTPUT
VIDEO
OUTPUT
SURROUND
OUTPUT
L
R
FRONT
OUTPUT
L
R
DVD/multi-channel decoder
with multi-channel analog
output jacks
03_connecting_up.fm 17
Connecting up 03
18
En
Connecting video components
Connect your video components to the jacks as shown below. With digital video components (like a DVD player), you
must use the connections shown on this page for the video signal, but in order to hear a digital source (like a DVD)
you should hook up the audio to a digital input (see page 16). It is also a good idea to hook up your digital components
with analog audio connections (see page 17).
For better quality video, you can hook up using the component video jacks or the S-video jacks (quality descends in
this order) on the rear of the receiver instead of the regular video jacks. (With the VSX-2014i-G, you can connect video
components and your TV using different types of video cables. See
About the video converter
on page 15.)
When connecting your equipment, always make sure the power is turned off and the power cord is disconnected from
the AC outlet.
The arrows indicate the direction of the signal.
Note that the illustration above shows the VSX-2014i-G however, connection for the VSX-1014-S is the same.
Important
VSX-2014i-G only
Make sure you dont connect your
TV to the
MONITOR OUT
jacks for
MULTI-ROOM &
SOURCE
located above the proper
MONITOR OUT
jacks.
VSX-1014-S only
Make sure to use the same type of
cable for your video connections as you used to
connect your TV.
Connecting to the front panel video terminal
Front video connections are accessed via the front panel
using the
VIDEO2
button. There are standard audio/
video jacks as well as an S-video jack and an optical
input. Hook them up the same way you made the rear
panel connections.
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/
SAT
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI-
ROOM &
SOURCE
AUDIO
VIDEO S-VIDEO
RS - 232C
IN
IN
OUT
OUT
OUT
ANTENNA
AM LOOP
FMUNBAL 75
12V
TRIGGER
Y
PR
PB
PR
Y
PB
PR
1 2
2
IN 1
R
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
REC
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN
(DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN OUT
DIGITAL (TV/SAT)
4
3
2 1
1 4
TWOVOL
11
A R L R
FRONT CENTER SURROU
220V
110V
120-
OUT
PRE
OUT
CEN-
TER
SUR-
ROUND
SUR-
ROUND
FRONT
SUBW.
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
IN
OUT
OUT
Y
PB
PR
PB
IN
L
L
L
OUT IN
OUTPUT
VIDEO
L
R
OUTPUT INPUT
VIDEO
L
R
VIDEO
L
R
OUTPUT
VIDEO
L
R
INPUT
VIDEO
Video deck
TV (monitor)
TV tuner
(or Satellite tuner)
DVD or LD player
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
TONE
ACOUSTIC
EQ
i.LINK
SELECT
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MULTI
JOG
MULTI
JOG
L V R
VIDEO OUTPUT DIGITAL OUT
Video
camera
(etc.)
03_connecting_up.fm 18
Connecting up 03
19
En
Connecting antennas
Connect the AM loop antenna and the FM wire antenna
as shown below. To improve reception and sound quality,
connect external antennas (see
Using an external
antenna to improve FM reception
below). Always make
sure that the receiver is switched off and unplugged from
the wall outlet before making or changing any
connections.
Note that the illustration above shows the VSX-2014i-G
however, connection for the VSX-1014-S is the same.
FM wire antenna
Connect the FM wire antenna and fully extend vertically
along a window frame or another suitable place that
gives good reception.
AM loop antenna
Assemble the antenna and connect to the receiver as
shown above. The ground terminal (
) helps reduce
radio noise (it is not an earthing plug). Attach (if
necessary) and face in the direction that gives the best
reception.
Note that either wire can be inserted into the
respective terminals when connecting.
Antenna snap connectors
Twist the exposed wire strands together and insert into
the hole, then snap the connector shut.
Using an external antenna to improve FM
reception
Use an antenna adapter to connect an external FM
antenna using a coaxial 75
cable.
Attaching the antenna adapter
Use the antenna adaptor to terminate the coaxial cable
used with an external FM antenna.
1 Cut and strip the coaxial cable to the
specification shown in the diagram.
2 Open the adaptor body by pulling apart the tabs
on either side.
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/
SAT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI-
ROOM &
SOURCE
AUDIO
VIDEO S-VIDEO
RS - 232C
IN
IN
OUT
OUT
OUT
AM
NITOR OUT
12V
TRIGGER
Y
PR
PB
PR
Y
PB
PR
1 2
2
IN 1
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
REC
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN
(DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN
(
4
3
2 1
1 4
AM loop
antenna
FM wire antenna
10mm
AM LOOP
Antenna
adapter
Wire mesh Pull back Wire
1020 mm 5 9
Tabs
03_connecting_up.fm 19
Connecting up 03
20
En
3 Insert the cable as shown, then use a pair of
pliers to wrap the end of the wire around the
binding post. Snip off the excess wire.
4 Use pliers to secure the cable by pinching the
clamps together, as shown.
5 Push the body cover back on.
Using an external antenna to improve AM
reception
Connect a 56m length of vinyl-coated wire to the AM
antenna terminal without disconnecting the supplied AM
loop antenna.
For the best possible reception, suspend horizontally
outdoors.
AM LOOP
Outdoor
antenna
Indoor antenna
(vinyl-coated wire)
56m
03_connecting_up.fm 20
Connecting up 03
21
En
Connecting the speakers
A complete setup of eight speakers (including the subwoofer) is shown below, but everyones home setup will vary.
Simply connect the speakers you have in the manner shown below. The receiver will work with just two stereo speakers
(the front speakers in the diagram) but using at least three speakers is recommended, and a complete setup is best
for surround sound. If youre not using a subwoofer, change the front speaker setting (see
Speaker Setting
on page 44)
to large.
Make sure you connect the speaker on the right to the right terminal and the speaker on the left to the left terminal.
Also make sure the positive and negative (
+
/
) terminals on the receiver match those on the speakers.
You can use speakers with a nominal impedance between 616
(please see
Switching the speaker impedance
on
page 76 if you plan to use speakers with an impedance of
less than
8
).
Be sure to complete all connections before connecting this unit to the AC power source.
Note that the illustration above shows the VSX-2014i-G however, connection for the VSX-1014-S is the same.
Caution
These speaker terminals carry
HAZARDOUS LIVE
voltage
. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
Make sure no bare speaker wire is touching the back
panel when the unit is switched on. The power may
cut off as a safety measure.
Note
If you only have one surround back speaker, hook it
up to the surround back left (
Single
) terminal.
If you are planning on bi-amping your front speakers,
or setting up a separate speaker system in another
room, read through
Surround back speaker setting
on
page 38 and make sure to connect your speakers as
necessary (these connections are explained in
Other
connections
on page 55).
If you are using a THX certified subwoofer use the
THX INPUT
jack on the subwoofer (if your subwoofer
has one) or switch the filter position to
THX
on your
subwoofer.
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/
SAT
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI-
ROOM &
SOURCE
AUDIO
VIDEO S-VIDEO
RS - 232C
IN
IN
OUT
OUT
OUT
ANTENNA
AM LOOP FMUNBAL 75
MONITOR OUT
12V
TRIGGER
Y
Y
PB
PR
PB
PR
Y
PB
PR
1 2
2
IN 1
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
OUT
REC
IN
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN
(DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN OUT
DIGITAL (TV/SAT)
4
3
2 1
1 4
SPEAKERS
AC IN TWOVOLTAGE SELECTORS
230-240 V
120-127V 110V
A B R L R L
R L(Single)
FRONT CENTER SURROUND SURROUND BACK /
SELECTABLE
SELECTABLE
220V
220V
230-240V
110V
120- 127V
OUT
OUT
D-R/
APE/MD
DEO1
VR /
CR
PRE
OUT
CEN-
TER
CEN-
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
SUBW.
M
R L
R L
R L
R
L
LAY
LAY
REC
INPUT
Front speakers
L R C LS RS
Powered
subwoofer
SW
Surround speakers
SBL SBR
Surround back speakers Center speaker
03_connecting_up.fm 21
Connecting up 03
22
En
Speaker terminals
1 Twist exposed wire strands together.
2 Loosen speaker terminal and insert exposed
wire.
Make sure that all the bare speaker wire is twisted
together and inserted fully into the speaker terminal. Use
good quality speaker wire to connect the speakers to the
receiver.
3 Tighten terminal.
Hints on speaker placement
Speakers are usually designed with a particular
placement in mind. Some are designed to be
floorstanding, while others should be placed on stands to
sound their best. Some should be placed near a wall;
others should be placed away from walls. We have
provided a few tips on getting the best sound from your
speakers (following), but you should also follow the
guidelines on placement that the speaker manufacturer
provided with your particular speakers to get the most
out of them.
Place the front left and right speakers at equal
distances from the TV.
When placing speakers near the TV, we recommend
using magnetically shielded speakers to prevent
possible interference, such as discoloration of the
picture when the TV is switched on. If you do not have
magnetically shielded speakers and notice
discoloration of the TV picture, move the speakers
farther away from the TV.
If you're using a center speaker, place the front
speakers at a wider angle. If not, place them at a
narrower angle.
Place the center speaker above or below the TV so
that the sound of the center channel is localized at
the TV screen. Also, make sure the center speaker
does not cross the line formed by the leading edge of
the front left and right speakers.
It is best to angle the speakers towards the listening
position. The angle depends on the size of the room.
Use less of an angle for bigger rooms.
Surround and surround back speakers should be
positioned 60 cm90 cm higher than your ears and
titled slight downward. Make sure the speakers don't
face each other. For DVD-Audio, the speakers should
be more directly behind the listener than for home
theater playback.
To achieve the best possible surround sound, install
your speakers as shown below. Be sure all speakers
are installed securely to prevent accidents and
improve sound quality.
Caution
If you choose to install the center speaker on top of
the TV, be sure to secure it with putty, or by other
suitable means, to reduce the risk of damage or
injury resulting from the speaker falling from the TV
in the event of external shocks such as earthquakes.
Overhead view of speaker setup
You can also refer to the 3-D speaker setup illustration on
page 10.
The diagrams below show suggested surround and
surround back speaker orientation. The first diagram (
fig.
A
) shows orientation with one surround back speaker (or
none) connected. The second (
fig. B
) shows orientation
with two surround back speakers connected.
If you have two surround back speakers THX
recommends placing them together and the same
distance from your listening position.
10mm
1 2 3
Surround
Left
Surround
Right
Listening Position
Front
Left
Front
Right Center
Surround Back Surround Back
Single Surround Back Speaker
Left Right
Subwoofer
90~120
fig. A fig. B
LS
LS
RS
RS
SB
LS RS
0~60
SBL
SBL
SBR
SBR
03_connecting_up.fm 22
Connecting up 03
23
En
3-D view of
7.1 channel
speaker setup
AC power cord
After youve finished making all connections, plug the
receiver into an AC outlet. The type of cord and the plug
converter which can be used depends on the power
voltage in each region or country. Please make sure you
use the correct cord and plug converter due to the
possibility of fire or other hazard if used incorrectly (see
below).
Make sure you have completely inserted the AC
power cord into the
AC IN
inlet on the rear panel.
Do not use any power cord other than the one
supplied with this unit.
This unit should be disconnected by removing the
power plug from the wall socket when not in regular
use (ex. when on vacation).
Power cord caution
Handle the power cord by the plug. Do not pull out
the plug by tugging the cord and never touch the
power cord when your hands are wet as this could
cause a short circuit or an electric shock. Do not
place the unit, a piece of furniture, etc., on the power
cord, or pinch the cord. Never make a knot in the cord
or tie it with other cords. The power cords should be
routed such that they are not likely to be stepped on.
A damaged power cord can cause a fire or give you
an electrical shock. Check the power cord once in a
while. When you find it damaged, ask your nearest
Pioneer authorized independent service company for
a replacement.
Operating other Pioneer components
Many Pioneer components have SR
CONTROL
jacks
which can be used to link components together so that
you can use just the remote sensor of one component.
When you use a remote control, the control signal is
passed along the chain to the appropriate component.
Note that if you use this feature,
make sure that you also
have at least one set of analog audio or video jacks
connected
to another component for grounding
purposes.
Note
If you want to control all your components using this
receivers remote control, refer to
Controlling the rest
of your system
on page 50.
If you have connected a remote control to the
CONTROL IN
jack (using a mini-plug cable), you
won't be able to control this unit using the remote
sensor.
AC power cord and converter plug use
Region Plug type
For European type region
Caution
Do not use this power cord
set in Singapore and
Malaysia.
European two-pin plug
For regions with two pin flat-
bladed plug
Caution
Do not use this power cord
set in Taiwan.
European two-pin plug with two-pin
flat-bladed converter plug
For Taiwan exclusively
Caution
For use in Taiwan only. In
other areas, please do not
use.
Taiwanese two-pin flat-bladed plug
CONTROL
OUT IN
OUT
IN
CONTROL
Receiver
Remote
control
unit
Other Pioneer products
with CONTROL terminals
Connect to CONTROL
terminal of other
Pioneer products
03_connecting_up.fm 23
Controls and displays 04
24
En
Chapter 4:
Controls and displays
Front panel
MASTER VOLUME
DVD/LD TV/SAT DVR/VCR VIDEO1
CD
CD-R/
TAPE/MD
MULTI JOG
TUNER VIDEO2
MODE
ENTER
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP
FL
DIMMER
INPUT
ATT RETURN
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
DIALOG
ENHANCEMENT
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
11
1 11 7 2 3 4 5 6 8 9 10
14 15 16 17 20
23 22 21 25
12
24
13 18 19
11 14 15 17 20 12 19
22 27 28 26 21 25 24
13 18
VSX-2014i-G model
VSX-1014-S model
VSX_2014TX.book.fm 24
Controls and displays 04
25
En
1 MULTI JOG dial
Use the
MULTI JOG
dial to select various settings and
menu options.
2
STANDBY/ON
Switches the receiver between on and standby.
3 LISTENING MODE SELECT
Use with the
MULTI JOG
dial to select the various
listening modes (page 30).
4 ENTER
5 Character display
See
Display
on page 26.
6 Remote sensor
Receives the signals from the remote control.
7 i.LINK indicator
(VSX-2014i-G model only)
Lights when an i.LINK-equipped audio component is
selected (page 59).
8 MCACC indicator
Lights when Acoustic Calibration EQ (page 33) is on
(Acoustic Calibration EQ is automatically set to
ALL CH
ADJUST
after the Auto MCACC Setup (page 11) or EQ
Auto Setting (page 41) is complete).
9 Input select buttons
Press to select an input source.
10 MASTER VOLUME dial
11 Front panel controls
To access the front panel controls, push gently on the
lower third portion of the panel with your finger.
12 TUNER CONTROL
TUNER EDIT
Use with the
MULTI JOG
dial to memorize and name
stations for recall
(page 48).
TUNING/STATION
Use with the
MULTI JOG
dial to select station presets
and radio frequencies. (page 47).
BAND
Switches between AM and FM radio bands (page 47).
MPX
Press to receive a radio broadcast in mono
(page 47).
13 MIDNIGHT/LOUDNESS
Use Midnight when listening to movie soundtracks at low
volume. Use Loudness to boost the bass and treble at low
volume (page 36).
14 TONE
When the
STEREO
mode is selected, press this button to
access the bass and treble controls, which you can then
adjust with the
MULTI JOG
dial.
15 ACOUSTIC EQ
Press to select an Acoustic Calibration EQ setting
(page 33).
16 i.LINK SELECT
(VSX-2014i-G model only)
Use with the
MULTI JOG
dial to select unassigned i.LINK
components (page 59).
17 MULTI CH IN
Press to select the component connected to the
MULTI
CH IN
terminals (for example, a DVD-Audio player). See
Selecting the multichannel analog inputs
on page 37.
18 SIGNAL SELECT
Use to select an input signal (page 33).
19 EXTENDED MODE
Selects the surround back channel mode (page 34) or
virtual surround back mode (page 35).
20 SPEAKERS
Use to change the speaker system (page 55).
21 VIDEO2 INPUT
See
Connecting to the front panel video terminal
on
page 18.
22 MCACC SETUP MIC jack
Use to connect the supplied microphone.
23 MULTI ROOM controls
(VSX-2014i-G model only)
If you've made multi-room connections (see
Multi-room
listening
on page 57) use these buttons to control the sub
room from the main room (see
Using the sub room
controls
on page 58).
24 System Setup menu controls
SYSTEM SETUP
Use with the
MULTI JOG
dial to access the System
Setup menu (page 11, page 38, page 63).
RETURN
Press to confirm and exit the current menu screen.
25 PHONES jack
Use to connect headphones. When the headphones are
connected, there is no sound output from the speakers.
26 DIALOG ENHANCEMENT
(VSX-1014-S model only)
Use to make dialog stand out when watching TV or a
movie (page 36).
27 FL DIMMER
(VSX-1014-S model only)
Dims or brightens the display. Switching the dimmer to
lowest setting will also switch off the MCACC and i.LINK
indicators.
28 INPUT ATT (VSX-1014-S model only)
Attenuates (lowers) the level of an analog input signal to
prevent distortion.
MASTER VOLUME
DVD/LD TV/SAT DVR/VCR VIDEO1
CD CD-R/ TAPE/MD
STANDBY/ON
MULTI JOG
TUNER VIDEO2
VSX-52TX
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
L
Left front channel
C
Center channel
R
Right front channel
LS
Left surround channel
S
Surround channel (mono) or surround back
channel
RS
Right surround channel
LFE
Low frequency effects channel
5 Matrix decoding format indicators
2
PLII
This lights to indicate Pro Logic II / Pro Logic IIx
decoding (see
Listening in surround sound
on
page 30 for more on this).
Neo:6
When one of the Neo:6 modes of the receiver is on,
this lights to indicate Neo:6 processing (see
Listening
in surround sound
on page 30 for more on this).
6 Listening mode indicators
THX
Lights when one of the Home THX modes is selected.
VIR.SB
Lights during Virtual surround back processing.
ADV.SURR.
Lights when one of the Advanced Surround modes
has been selected.
AUTO SURR.
Lights when the Auto Surround feature is switched
on (see
Auto playback
on page 30).
7 MIDNIGHT / LOUDNESS
When Midnight or Loudness listening is switched on, the
corresponding indicator shows in the display.
8 Input source indicators
Light to indicate the input source you have selected.
9 MULTI-ROOM
(VSX-2014i-G model only)
Lights when the multi-room feature is active (page 57).
10 ATT
Lights when
INPUT ATT
is used to attenuate (reduce) the
level of the analog input signal.
11 OVER
Lights to indicate that the level of an analog source is too
high. Use the attenuator (
INPUT ATT
) to reduce it.
2 1 3 4
15 12 6 14 13 17 16 11
5 6 8 10 9 7
SIGNAL
AUTO
SP AB
DIGITAL DIGITAL L
LS
C
S
R
RS
LFE PL
ADV.SURR. VIR.SB
Neo THX DVD DVR
TUNER CD-R CD
VIDEO1
VIDEO2
TV 6
DTS
SR AUTO SURR. MONOSTEREO TUNED DE MIDNIGHT LOUDNESS
OVER
dB
MULTI- ROOM ATT SLEEP
ANALOG
VSX_2014TX.book.fm 26
Controls and displays 04
27
En
12 Master volume level
Shows the overall volume level.
80dB
indicates the
minimum level, and
+12dB
indicates the maximum level.
13 DE
Lights when Dialog Enhancement (
DIALOG
E
) is
switched on (page 36).
14 TUNER indicators
(page 47)
STEREO
Lights when a stereo FM broadcast is being received
in auto stereo mode.
MONO
Lights when the mono mode is set using the
MPX
button.
TUNED
Lights when a broadcast is being received.
15 Character display
Displays various system information (for example, the
reason an operation is not possible may flash in the
display).
16 SR
Lights when the SR+ control mode has been switched
on (see
Using the SR+ mode with a Pioneer plasma
display
on page 62).
17 SLEEP
Lights when the receiver is in sleep mode (page 37).
Remote control
1 RECEIVER
This switches between standby and on for this receiver.
2 INPUT SELECT
Use to select the input source.
3 MULTI CONTROL buttons
Press to select control of other components (see
Controlling the rest of your system
on page 50).
4 Number buttons and other receiver/component
controls
Use the number buttons to directly select a radio
frequency (page 47) or the tracks on a CD, DVD, etc.
DISC (ENTER)
can be used to enter commands for TV or
DTV, and can also be used to select a disc in a multi-CD
player.
+10
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
ENTER
TV CONTROL
RECEIVERCONTROL
SHIFT
VOL
DVD/LD TV/SAT DVR/VCR TVCONT
CD
TUNE
TUNE
ST ST
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
INPUT
SELECT
TV CH
DTVON/OFF
TUNER
DISPLAY
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
DTVINFO REC MUTE
TVVOL
CD-R/TAPE TUNER RECEIVER
ENTER
RECSTOP
HDD
CH CH
DVD
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
RECEIVER
4
3
5
7
8
10
9
6
11
12
13
14
15
2
1
VSX_2014TX.book.fm 27
Controls and displays 04
28
En
The following are accessed by pressing the
RECEIVER
button first:
INPUT ATT
Attenuates (lowers) the level of an analog input
signal to prevent distortion.
FL DIMMER
Dims or brightens the display. Switching the dimmer
to lowest setting will also switch off the MCACC and
i.LINK indicators.
SR+
Switches the SR+ mode on/off (page 62).
5 Tuner/component control buttons/SYSTEM
SETUP
The following button controls (except
SYSTEM SETUP
)
can be accessed after you have selected the
corresponding
MULTI CONTROL
button (
TUNER
,
DVD/
LD
,
TV/SAT
, etc.)
D. ACCESS
After pressing, you can access a radio station directly
using the number buttons (page 47).
TOP MENU
Displays the disc top menu of a DVD.
DTV MENU
Displays menus on a digital TV.
T. EDIT
Press to memorize and name a station for recall
(page 48).
GUIDE
Displays the guides on a digital TV.
SYSTEM SETUP
(Press
RECEIVER
first to access)
Use to access the System Setup menu (see page 38).
CLASS
Switches between the three banks (classes) of radio
station presets (page 48).
MENU
Displays the disc menu of DVD-Video discs. It also
displays TV and DTV menus.
BAND
Switches between the tuner AM and FM bands
(page 47).
RETURN
Press to confirm and exit the current menu screen
(also use to return to the previous menu with DVDs or
to select closed captioning with DTV).
6
(TUNE/ST +/) /ENTER
Use the arrow buttons when setting up your surround
sound system (see page 38). Also used to control DVD
menus/options and for deck 1 of a double cassette deck
player. Use the
TUNE +/
buttons to find radio
frequencies and use
ST +/
to find preset stations
(page 48).
7 TV CONTROL buttons
These buttons are dedicated to control the TV assigned to
the
TV CONT
button. Thus if you only have one TV to hook
up to this system assign it to the
TV CONT MULTI
CONTROL
button. If you have two TVs, assign the main
TV to the
TV CONT
button (see page 50 for more on this).
TV
Use to turn on/off the power of the TV.
TV VOL +/
Use to adjust the volume on your TV.
INPUT SELECT
Use to select the TV input signal.
TV CH +/
Use to select channels.
8 Component control buttons
The main buttons (
, etc.) are used to control a
component after you have selected it using the
MULTI
CONTROL
buttons.
The controls above these buttons can be accessed after
you have selected the corresponding
MULTI CONTROL
button (for example
DVD/LD
,
DVR/VCR
or
TV/SAT
(when connected to a DTV)).
DTV ON/OFF
Switches a digital TV on/off.
DTV INFO
Use to bring up information screens on a digital TV.
TUNER DISPLAY
Switches between named station presets and radio
frequencies (page 48).
MPX
Switches between stereo and mono reception of FM
broadcasts. If the signal is weak then switching to
mono will improve the sound quality (page 47).
AUDIO
Changes the audio language or channel on DVD
discs.
CH RETURN
Returns to the last channel selected with DTV, SAT
and some TVs.
SUBTITLE
Displays/changes the subtitles included in
multilingual DVD-Video discs.
VSX_2014TX.book.fm 28
Controls and displays 04
29
En
CH +/
Use to select channels when using a TV, VCR, DVR,
etc.
These DVR controls can be accessed by pressing
SHIFT
:
REC
Starts recording.
REC STOP
Stops recording.
HDD/DVD
These buttons switch between the hard disk and DVD
controls for DVD/HDD recorders.
9 RECEIVER CONTROL buttons
THX
Press to select a Home THX listening mode
(page 31).
STANDARD
Press for Standard decoding and to switch between
the various Pro Logic IIx and Neo:6 options (page 30).
ADV. SURR
Use to switch between the various surround modes
(page 31).
STEREO
Switches between direct and stereo playback. Direct
playback bypasses the tone controls and any other
signal processing for the most accurate reproduction
of a source (page 32).
AUTO SURR
Press to have the receiver automatically detect what
kind of source youre playing and select multichannel
or stereo playback as necessary (page 30).
ACOUSTIC EQ
Press to select an Acoustic Calibration EQ setting
(page 33).
SIGNAL SELECT
Use to select an input signal (page 33).
MIDNIGHT/LOUDNESS
Use Midnight when listening to movie soundtracks at
low volume. Use Loudness to boost the bass and
treble at low volume (page 36).
EFFECT/CH SEL
Press repeatedly to select a channel, then use /+ to
adjust the level
(page 45). Also adjusts the level of the
Advanced Surround effects (page 31) as well as
Dolby Pro Logic IIx Music (page 32) and Neo:6 Music
parameters (page 32). You can then use the
+
and
buttons to make these adjustments.
+/
Use to adjust the effect and channel levels, as well as
to change Dolby Pro Logic IIx and Neo:6 Music
parameter settings.
SLEEP (SHIFT & )
Use to put the receiver in sleep mode and select the
amount of time before the receiver turns off
(page 37).
DIALOG E (SHIFT & +)
Use to make dialog stand out when watching TV or a
movie (page 36).
10 SHIFT
Press to access the DVR controls (above the component
control buttons) as well as some
RECEIVER
controls.
11
SOURCE
Press to turn on/off other components connected to the
receiver (see page 50 for more on this).
12 Character display (LCD)
This display shows information when transmitting
control signals.
The following commands are shown when youre setting
the remote to control other components (see
Controlling
the rest of your system
on page 50):
SETUP
Indicates the setup mode, from which you choose the
options below.
PRESET
See
Selecting preset codes directly
on page 50.
LEARN
See
Programming signals from other remote controls
on page 51.
DIRECT F
See
Direct function
on page 52.
ERASE
See
Erasing one of the remote control button settings
on page 52.
RESET
See
Erasing all of the remote control presets
on
page 52.
READ ID
See
Confirming preset codes
on page 52.
13 RECEIVER
Switches the remote to control the receiver (used to
select the green commands above the number buttons
(
INPUT ATT
, etc). Also use this button to set up surround
sound (page 11, page 38).
14 VOL +/
Use to set the listening volume.
15 MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
VSX_2014TX.book.fm 29
Listening to your system 05
30
En
Chapter 5:
Listening to your system
Important
VSX-2014i-G model only
The listening modes and
many of the features described in this section are not
available when playing SACD or DVD-Audio discs
using the i.LINK connection.
Tip
The listening modes described below can also be
selected using the front panel controls. Simply press
LISTENING MODE SELECT
repeatedly to access the
modes you want, then use the
MULTI JOG
to select a
particular listening mode (after five seconds the
mode is automatically set).
Auto playback
There are many ways to listen back to sources using this
receiver, but for the simplest, most direct listening option
is the Auto Surround feature. With this, the receiver
automatically detects what kind of source youre playing
and selects multichannel or stereo playback as
necessary.
While listening to a source, press AUTO SURR for
auto playback of a source.
AUTO SURROUND
shows briefly in the display before
showing the decoding or playback format. Check the
digital format indicators in the front panel display to see
how the source is being processed.
Note
Stereo surround (matrix) formats are decoded
accordingly using
Neo:6 CINEMA
or
2
Pro Logic
IIx MOVIE
(see
Listening in surround sound
below for
more on these decoding formats).
The Auto Surround feature is canceled if you connect
headphones or select the multichannel analog
inputs.
Listening in surround sound
Using this receiver, you can listen to any source in
surround sound. However, the options available will
depend on your speaker setup and the type of source
youre listening to.
If you connected surround back speakers, see also
Using
the surround back channel (Extended mode)
on page 34.
Standard surround sound
The following modes provide basic surround sound for
stereo and multichannel sources.
While listening to a source, press STANDARD.
If necessary, press repeatedly to select a listening mode.
If the source is Dolby Digital, DTS, or Dolby Surround
encoded, the proper decoding format will
automatically be selected and shows in the display.
With two channel sources
, you can select from:
2
Pro Logic IIx MOVIE
Up to 7.1 channel sound,
especially suited to movie sources
2
Pro Logic IIx MUSIC
Up to 7.1 channel sound,
especially suited to music sources
2
PRO LOGIC
4.1 channel surround sound (sound
from the surround speakers is mono)
Neo:6 CINEMA
6.1 channel sound, especially
suited to movie sources
Neo:6 MUSIC
6.1 channel sound, especially suited
to music sources
With multichannel sources, if you have connected
surround back speaker(s) and have selected
Extended
ON
, you can select (according to format):
2
Pro Logic IIx MOVIE
See above (only available
when youre using two surround back speakers)
2
Pro Logic IIx MUSIC
See above
Dolby Digital EX
Creates surround back channel
sound for 5.1 channel sources and provides pure
decoding for 6.1 channel sources (like Dolby Digital
Surround EX)
DTS-ES
Allows you to hear 6.1 channel playback
with DTS encoded sources
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
05_playing_sources.fm 30
Listening to your system 05
31
En
Note
If the Extended mode (page 34) is switched to
OFF
, or
the surround back speakers are set to
NO
(this
happens automatically if the
Surround back speaker
setting
on page 38 is set to anything but
Normal
(SB)
),
2
Pro Logic IIx
becomes
2
Pro Logic II
(5.1
channel sound).
In modes that give 6.1 channel sound, the same
signal is heard from both surround back speakers.
Using the Home THX modes
THX and Home THX are technical standards created by
Lucasfilm Ltd. for cinema and home theater sound.
Home THX is designed to make home theater audio
sound more like what you hear in a cinema.
Different THX options will be available depending on the
source and the Extended mode setting (see
Using the
surround back channel (Extended mode)
on page 34 for
more on this).
Press THX to select a THX listening mode.
With two channel sources
, select a matrix-decoding
process for the
THX CINEMA
mode (see
Listening in
surround sound
above for an explanation of each
process):
2
Pro Logic IIx MOVIE
2
PRO LOGIC
Neo:6 CINEMA
With multichannel sources
, you can select (according to
format):
THX CINEMA
Gives you cinema-quality sound from
your home theatre system using all the speakers in
your setup
THX Surround EX
Allows you to hear 6.1 or 7.1
channel playback with 5.1 channel sources
2
Pro Logic IIx MOVIE
Especially suited to movie
sources, this allows you to hear 7.1 channel playback
with 5.1 channel sources (only available when youre
using two surround back speakers)
DTS-ES
Allows you to hear 6.1 channel playback
with DTS encoded sources
Note
You wont be able to use the THX options with 88.2/
96kHz PCM or DTS 96kHz/24 bit sources, or with the
headphones connected.
Using the Advanced surround effects
The Advanced surround effects can be used for a variety
of additional surround sound effects. Most Advanced
Surround modes are designed to be used with film
soundtracks, but some modes are also suited for music
sources. Try different settings with various soundtracks
to see which you like.
Press ADV. SURR (ADVANCED SURROUND)
repeatedly to select a listening mode.
ADVANCED MOVIE
Simulates the relaxed
environment of a movie theater, and is suitable for
watching movies.
ADVANCED MUSIC
Simulates the acoustic
environment of a large concert hall and is suitable for
music or musical sources.
TV SURROUND
This mode produces surround
sound for both mono and stereo TV sources. It is
useful for older movies recorded with mono
soundtracks.
SPORTS
This is designed for sports programs with
a lot of action, adding to the excitement by bringing
background action to the forefront.
GAME
Useful when playing video games. It works
especially well with sound moving from left to right in
game software with a lot of movement.
EXPANDED
This mode is especially designed to
give sound depth to stereo sources, and lets you hear
two-channel (stereo) signals as simulated
multichannel surround sound. Use with Dolby Pro
Logic for a stereo surround effect. You can also use
with Dolby Digital sources for a wider stereo field
than the Standard modes.
7ch STEREO
This can be selected to give
multichannel sound to a stereo source, using all of
the speakers in your setup.
PhonesSurround
When listening through
headphones, you can still get the effect of overall
surround.
Note
Depending on the source and the sound mode you
have selected, you may not get sound from the
surround back speakers in your setup. For more on
this, refer to
Using the surround back channel
(Extended mode)
on page 34.
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
AUDIO SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
AUDIO SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
05_playing_sources.fm 31
Listening to your system 05
32
En
If you press
ADV. SURR
when the headphones are
connected, the
PhonesSurround
mode will
automatically be selected.
You cant use the Advanced Surround effects with
88.2/96kHz PCM or DTS 96kHz/24 bit sources.
Tip
When an Advanced Surround listening mode is
selected, the effect level can be adjusted in the range
of
10
to
90
by pressing
EFFECT/CH SEL
(until
EFFECT
shows in the display). The effect level can be set for
each Advanced Surround mode by pressing
+
/
.
Dolby Pro Logic IIx Music settings
When listening to 2-channel sources in Dolby Pro Logic
IIx Music mode, there are three further parameters you
can adjust: Center Width, Dimension, and Panorama.
1 With
2
Pro Logic IIx MUSIC mode active, press
EFFECT/CH SEL repeatedly to select CENTER WIDTH,
DIMENSION or PANORAMA.
CENTER WIDTH
Provides a better blend of the front
speakers by spreading the center channel between
the front right and left speakers, making it sound
wider (higher settings) or narrower (lower settings).
(This is applicable only when using a center speaker.)
DIMENSION
Adjusts the depth of the surround
sound balance from front to back, making the sound
more distant (minus settings), or more forward
(positive settings).
PANORAMA
Extends the front stereo image to
include the surround speakers for a wraparound
effect.
2 Use the +/ buttons to adjust the setting.
Center Width is adjustable between
0
and
7
(default :
3
);
Dimension between
3
and
+3
(default :
0
); Panorama is
On
or
Off
(default :
Off
).
3 Press EFFECT/CH SEL again to adjust other
settings.
Note
If the Extended mode is switched off,
2
Pro Logic IIx
(above) becomes
2
Pro Logic II
(5.1 channel
sound), however the above setting will still be
effective.
Neo:6 Music settings
Default setting:
2
When listening to 2-channel sources in Neo:6 Music
mode, you can adjust the center image to create a wider
stereo effect with vocals. Note that this is only available
when using a center speaker.
1 With Neo:6 MUSIC mode active, press EFFECT/CH
SEL repeatedly to select C. IMAGE.
2 Use the +/ buttons to adjust the setting.
Adjust the effect from
0
(all center channel sent to front
right and left speakers) to
5
(center channel sent to the
center speaker only).
Listening in stereo
When you select
STEREO
or
DIRECT
, you will hear the
source through just the front left and right speakers (and
possibly your subwoofer depending on your speaker
settings). Dolby Digital and DTS multichannel sources
are downmixed to stereo.
While listening to a source, press STEREO for
stereo playback.
Press repeatedly to switch between:
STEREO
The audio is heard with your surround
settings (such as channel level) and you can still use
digital processing (such as the Midnight, Loudness,
and Tone control functions).
DIRECT
Bypass all effects and surround settings so
that the audio remains as close to the source audio
signal as possible.
Note
If you switch on any signal processing features (for
example, the Midnight listening mode or the tone
controls) when
DIRECT
is selected, the receiver
automatically switches to
STEREO
.
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
05_playing_sources.fm 32
Listening to your system 05
33
En
Listening with Acoustic Calibration
EQ
Default setting:
OFF
/
ALL CH ADJ
(after the Auto
MCACC Setup or EQ Auto Setting)
You can listen to sources using the Acoustic Calibration
Equalization set in
Automatically setting up for surround
sound (MCACC)
on page 11 or
Acoustic Calibration EQ
on
page 41. Refer to these pages for more on Acoustic
Calibration Equalization.
The illustration above shows the VSX-2014i-G model.
While listening to a source, press ACOUSTIC EQ.
Press repeatedly to select between:
ALL CH ADJ
No special weighting is given to any
one channel.
FRONT ALIGN
All speakers are heard in
accordance with the front speaker settings.
CUSTOM 1/2
Custom settings
OFF
Switches Acoustic Calibration EQ off.
The MCACC indicator on the front panel lights when
Acoustic Calibration EQ is active.
Note
You cant use Acoustic Calibration EQ when
MULTI
CH IN
is switched on, and it has no effect when
headphones are connected.
If you switch on Acoustic Calibration EQ when
DIRECT
is selected, the receiver automatically
switches to
STEREO
.
Choosing the input signal
You need to hook up a component to both analog and
digital inputs on the rear of the receiver to select between
input signals.
The illustration above shows the VSX-2014i-G model.
Press SIGNAL SELECT to select the input signal
corresponding to the source component.
Each press cycles through the options as follows:
AUTO
The receiver selects the first available signal
in the following order:
(VSX-2014i-G only);
DIGITAL
;
ANALOG
.
ANALOG
Selects the analog inputs.
DIGITAL
Selects the digital input.
(VSX-2014i-G only) Selects the i.LINK input.
When set to
DIGITAL
or
AUTO
,
2
DIGITAL
lights when
a Dolby Digital signal is input, and
DTS
lights when a DTS
signal is input.
Note
This receiver can only play back Dolby Digital, PCM
(32kHz96 kHz) and DTS digital signal formats
(including DTS 96kHz/24 bit). With other digital
signal formats, set to
ANALOG
.
VSX-2014i-G only
If you are using the i.LINK
connectors, DVD-A (including 192 kHz) and SACD
are also supported.
You may get digital noise when a LD or CD player
compatible with DTS is playing an analog signal. To
prevent noise, make the proper digital connections
(page 16) and set the signal input to
DIGITAL
.
Some DVD players dont output DTS signals. For
more details, refer to the instruction manual supplied
with your DVD player.
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
05_playing_sources.fm 33
Listening to your system 05
34
En
Using the surround back channel
(Extended mode)
Default setting:
Extended ON
You can have the receiver automatically use 6.1 or 7.1
decoding for 6.1 encoded sources (for example, Dolby
Digital EX or DTS-ES), or you can choose to always use
6.1 or 7.1 decoding (for example, with 5.1 encoded
material). With 5.1 encoded sources, a surround back
channel will be generated, but the material may sound
better in the 5.1 format for which it was originally
encoded (in which case, you can simply switch the
Extended mode off).
The table below indicates when you will hear the
surround back channel when playing various kinds of
sources. (
=Sound plays through surround back
speaker(s))
The illustration above shows the VSX-2014i-G model.
Press EXTENDED MODE (front panel) repeatedly
to cycle the surround back channel options.
Each press cycles through the options as follows:
Extended ON
6.1 or 7.1 decoding is always used
(for example, a surround back channel will be
generated for 5.1 encoded material)
Extended AUTO
Automatically switches to 6.1 or
7.1 decoding for 6.1 encoded sources (for example,
Dolby Digital EX or DTS-ES)
Extended OFF
Maximum 5.1 playback
Note
You must have surround back speakers connected
(and set to
LARGE
or
SMALL
in the
Speaker Setting
on
page 44) and the
Surround back speaker setting
on
page 38 must be set to
Normal (SB)
to hear the
surround back channel.
You cant use the surround back channel with
headphones, the
STEREO
/
DIRECT
mode.
You cant hear the surround back channel with DTS
96kHz/24 bit or PCM 96/88.2kHz sources.
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
Type of source
Extended
mode
Standard / THX
Advanced
surround
Multichannel
sources
Stereo sources
2
Pro Logic II x
2
Pro Logic
Neo:6
Dolby Digital EX/DTS-ES encoded
multichannel source with 6.1ch
surround
ON
AUTO
Dolby Digital/DTS encoded
multichannel source
ON
AUTO
Dolby Digital encoded stereo source;
other digital stereo source
ON
AUTO
DTS encoded stereo source
ON
AUTO
Analog 2-channel (stereo) source
ON
AUTO
05_playing_sources.fm 34
Listening to your system 05
35
En
Using the Virtual Surround Back
mode (VirtualSB)
When youre not using surround back speakers,
selecting this mode allows you to hear a virtual surround
back channel through your surround speakers. For
example, you can choose to listen to sources with no
surround back channel information (for example, 5.1
encoded material) with emulated 6.1 encoding
(
VirtualSB ON
). Sometimes the material may sound
better in the 5.1 format for which it was originally
encoded. In this case you can have the receiver only
apply this effect to 6.1 encoded sources like Dolby Digital
EX or DTS-ES (
VirtualSB AUTO
), or you can simply
switch it off (
VirtualSB OFF
).
The table indicates when you will hear the virtual
surround back channel. (
=Virtual surround back
channel is active)
The illustration above shows the VSX-2014i-G model.
Press EXTENDED MODE (front panel) repeatedly
to cycle the virtual surround back channel options.
Each press cycles through the options as follows:
VirtualSB ON
Virtual Surround Back is always used
(for example, on 5.1 encoded material)
VirtualSB AUTO
Virtual Surround Back is
automatically applied to 6.1 encoded sources (for
example, Dolby Digital EX or DTS-ES)
VirtualSB OFF
Virtual Surround Back mode is
switched off
Note
You cant use the Virtual Surround Back mode with
headphones, or with the
THX
or
STEREO
/
DIRECT
modes.
You can only use the Virtual Surround Back mode if
the surround speakers are on and the
Surr Back
setting is set to
NO
in the
Speaker Setting
on page 44.
You cant hear the virtual surround back channel with
DTS 96kHz/24 bit or PCM 96/88.2kHz sources.
The Virtual Surround Back mode cannot be applied
to sources that do not have surround channel
information.
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
Type of source
VirtualSB
mode
Standard
Advanced
surround
Multichannel
sources
Stereo sources
2
Pro Logic II
2
Pro Logic
Neo:6
Dolby Digital EX/DTS-ES encoded
multichannel source with 6.1ch
surround
ON
AUTO
Dolby Digital/DTS encoded
multichannel source
ON
AUTO
Dolby Digital/DTS encoded stereo
source; other digital stereo source
ON
AUTO
Analog 2-channel (stereo) source
ON
AUTO
05_playing_sources.fm 35
Listening to your system 05
36
En
Using Loudness and Midnight
listening
The Loudness listening feature can be used to get good
bass and treble from music sources at low volume levels.
The Midnight listening feature allows you to hear
effective surround sound of movies at low volume levels.
The effect automatically adjusts according to the volume
at which youre listening.
The illustration above shows the VSX-2014i-G model.
Press MIDNIGHT/LOUDNESS to switch between
MIDNIGHT, LOUDNESS, and OFF.
Note
You cant use
MIDNIGHT/LOUDNESS
with DTS
96kHz/24 bit or PCM 96/88.2kHz sources, or when
MULTI CH IN
, or one of the THX modes has been
selected.
If you switch on Loudness or Midnight listening when
DIRECT
is selected, the receiver automatically
switches to
STEREO
.
Enhancing dialog
Default setting:
DIALOG E OFF
The Dialog Enhancement feature localizes dialog in the
center channel to make it stand out from other
background sounds in a TV or movie soundtrack.
Press SHIFT+DIALOG E to switch dialog
enhancement on or off.
Note
You cant use dialog enhancement with DTS 96kHz/
24 bit or PCM 96/88.2kHz sources, or when one of the
THX modes has been selected.
Tip
VSX-1014-S model only
You can also switch Dialog
Enhancement on or off using the front panel:
Using the tone controls
Depending on what you are listening to, you may want to
adjust the bass or treble using the front panel tone
control.
The illustration above shows the VSX-2014i-G model.
1 Press TONE to select the frequency you want to
adjust.
Each press switches between
BASS
and
TREBLE
.
2 Use the MULTI JOG dial to change the amount of
bass or treble as necessary.
The bass and treble can be adjusted from
6
to
+6
(dB).
Wait about five seconds for your changes to be input
automatically.
Note
You can only use the tone controls when
STEREO/
DIRECT
is selected.
DIRECT
will switch to
STEREO
when the tone controls are used.
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN
INPUT
ATT
FL
DIMMER
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
DIALOG
ENHANCEMENT
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
STANDBY/ON
MULTI JOG
LISTENING MODE
SELECT
ENTER
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
05_playing_sources.fm 36
Listening to your system 05
37
En
Playing other sources
1 Turn on the power of the playback component.
2 Turn on the power of the receiver.
3 Select the source you want to playback.
Use the
MULTI CONTROL
buttons (or
INPUT SELECT
).
4 Start playback of the component you selected in
step 1.
Selecting the multichannel analog
inputs
If you have connected a decoder or a DVD player with
multichannel analog outputs to this receiver (page 17),
you must select the analog multichannel inputs for
surround sound playback.
The illustration above shows the VSX-2014i-G model.
1 Make sure you have set the playback source to
the proper output setting.
For example, you might need to set your DVD player to
output multichannel analog audio.
2 Press MULTI CH IN on the front panel.
To cancel playback from the multichannel inputs, press
MULTI CH IN
once again.
Note
When playback from the multichannel inputs is
selected, you cant use the
ACOUSTIC CAL EQ
,
DIALOG E
,
SIGNAL SELECT
,
INPUT ATT
,
TONE
, and
MIDNIGHT/LOUDNESS
buttons, as well as any of
the listening modes (including
STEREO/DIRECT
and
the Extended mode).
When playback from the multichannel inputs is
selected, only the volume and channel levels can be
set.
You cant listen to your speaker B (Second Zone)
system during playback from the multichannel
inputs.
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
Press SHIFT+SLEEP repeatedly to set the sleep
time.
Note
You can check the remaining sleep time at any time
by pressing
SHIFT+SLEEP
once. Pressing repeatedly
will cycle through the sleep options again.
The sleep timer affects the sub room when the multi-
room feature is on.
You can also switch off the sleep timer simply by
switching off the receiver.
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
DVD/LD TV/SAT DVR/VCR TVCONT
CD CD-R/TAPE TUNER RECEIVER
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
RECEIVERCONTROL
SHIFT
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
Off
30 min 60 min
90 min
05_playing_sources.fm 37
The System Setup menu 06
38
En
Chapter 6:
The System Setup menu
Making receiver settings from the
System Setup menu
The following section shows you how to make detailed
settings to specify how youre using the receiver (for
example, if you want to set up two speaker systems in
separate rooms), and also explains how to fine-tune
individual speaker system settings to your liking.
1 Switch on the receiver and your TV.
Use the
RECEIVER
button to switch on.
If headphones are connected to the receiver,
disconnect them.
2 Press RECEIVER on the remote control, then press
the SYSTEM SETUP button.
An on-screen display (OSD) appears on your TV. Use the
///
buttons and
ENTER
on the remote control to
navigate through the screens and select menu items.
Press
RETURN
to confirm and exit the current menu.
Press
SYSTEM SETUP
at any time to exit the System
Setup menu.
3 Select the setting you want to adjust.
Surr Back System
Specify how you are using your
surround back speakers (see
Surround back speaker
setting
below).
AUTO MCACC
This is a quick and effective
automatic surround setup (see
Automatically setting
up for surround sound (MCACC)
on page 11).
MANUAL MCACC
Fine tune your speaker settings
and customize the Acoustic Calibration EQ (see
Manual MCACC speaker setup
below).
Manual SP Setup
Specify the size, number,
distance and overall balance of the speakers youve
connected (see
Manual speaker setup
on page 43).
Input Assign
Specify what youve connected to the
digital and component video inputs (see
The Input
Assign menu
on page 63).
Other Setup
Make customized settings to reflect
how you are using the receiver (see
The Other Setup
menu
on page 65).
Surround back speaker setting
Default setting:
Normal (SB)
There are several ways you can use the surround back
speaker channels with this system. In addition to a
normal home theater setup where they are used for the
surround back speakers, they can be used for bi-amping
the front speakers or as a separate speaker system in
another room.
1 Select Surr Back System from the System Setup
menu.
See
Making receiver settings from the System Setup menu
above if youre not already at this screen.
+10
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
ENTER
TV CONTROL
VOL
DVD/LD TV/SAT DVR/VCR TVCONT
CD
ST ST
INPUT
SELECT
TV CH
DTVON/OFF
TUNER
DISPLAY
MPX
AUDIO
CHRETURN
SUBTITLE
DTVINFO REC MUTE
TVVOL
CD-R/TAPE TUNER RECEIVER
ENTER
RECSTOP
HDD DVD
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
TUNE
TUNE
System Setup
[ 1. Surr Back System ]
[ 2. AUTO MCACC ]
[ 3. MANUAL MCACC ]
[ 4. Manual SP Setup ]
[ 5. Input Assign ]
[ 6. Other Setup ]
Enter : Select
Return : Exit
System Setup
[ 1. Surr Back System ]
[ 2. AUTO MCACC ]
[ 3. MANUAL MCACC ]
[ 4. Manual SP Setup ]
[ 5. Input Assign ]
[ 6. Other Setup ]
Enter : Select
Return : Exit
VSX_2014TX.book.fm 38
The System Setup menu 06
39
En
2 Select the surround back speaker setting.
Normal (SB)
Select for normal home theater use
with surround back speakers in your main (speaker
system A) setup.
Second Zone
Select to use the (surround back) B
speaker terminals to listen to stereo playback in
another room (see
Second Zone speaker B setup
on
page 55).
Front Bi-Amp
Select this setting if youre bi-
amping your front speakers (see
Bi-amping your front
speakers
on page 56).
3 When youre finished, press RETURN.
You will return to the System Setup menu.
Manual MCACC speaker setup
You can use the settings in the Manual MCACC setup
menu to make detailed adjustments when youre more
familiar with the system. Before making these settings,
you should have already completed
Automatically setting
up for surround sound (MCACC)
on page 11.
You only need to make these settings once (unless you
change the placement of your current speaker system or
add new speakers).
Important
For some of the settings below, youll have to connect
the setup microphone to the front panel and place it
about ear level at your normal listening position. See
Automatically setting up for surround sound (MCACC)
on page 11 if youre unsure how to do this. Also see
Other problems when using the Auto MCACC Setup
on page 13 for notes regarding high background
noise levels and other possible interference.
If youre using a subwoofer, switch it on and turn up
the volume to the middle position.
1 Select MANUAL MCACC from the System Setup
menu.
See
Making receiver settings from the System Setup menu
above if youre not already at this screen.
2 Select the setting you want to adjust.
If youre doing this for the first time, you might want to
make these settings in order.
Fine Ch Level
Make fine adjustments to the overall
balance of your speaker system (see
Fine Channel
Level
below).
Fine Ch Distance
Make precise delay settings for
your speaker system (see
Fine Channel Distance
on
page 40).
The last five settings are specifically for customizing the
parameters explained in
Acoustic Calibration EQ
below:
EQ AUTO Setting
Measure the acoustic
characteristics of your room and automatically
adjust the frequency balance of your speaker system
(see
Setting the Acoustic Calibration EQ automatically
below).
EQ Data Copy
Copy Acoustic Calibration EQ
settings for manual adjustment (see
Copying your
Acoustic Calibration EQ settings
below).
EQ CUSTOM1/2 Adjust
Make detailed manual
adjustments to your custom Acoustic Calibration EQ
settings (see
Setting the Acoustic Calibration EQ
manually
on page 42).
EQ Data Check
Check the
ALL CH ADJUST
,
FRONT ALIGN
and custom settings using the on-
screen display (see
Checking your Acoustic
Calibration EQ settings
on page 42).
1. Surround Back System
Surround Back Output
[ Normal(SB) ]
System Setup
[ 1. Surr Back System ]
[ 2. AUTO MCACC ]
[ 3. MANUAL MCACC ]
[ 4. Manual SP Setup ]
[ 5. Input Assign ]
[ 6. Other Setup ]
Enter : Select
Return : Exit
3.MANUAL MCACC
[ a .Fine Ch Level ]
[ b .Fine Ch Distance ]
[ c .EQ AUTO Setting ]
[ d .EQ Data Copy ]
[ e .EQ CUSTOM1 Adjust ]
[ f .EQ CUSTOM2 Adjust ]
[ g .EQ Data Check ]
VSX_2014TX.book.fm 39
The System Setup menu 06
40
En
Fine Channel Level
Default setting:
0dB
(all channels)
You can achieve better surround sound by properly
adjusting the overall balance of your speaker system. The
following setting can help you make detailed
adjustments that you may not achieve using the
Manual
speaker setup
on page 43.
1 Select Fine Ch Level from the Manual MCACC
setup menu.
The volume increases to the
0dB
reference level.
2 Adjust the level of the left channel.
This will be the reference speaker level, so you may want
to keep the level around
0dB
so that youll have plenty of
room to adjust the other speaker levels.
After pressing
ENTER
, test tones will be output
3 Select each channel in turn and adjust the levels
(
+/ 10dB
)
as necessary.
Use
/
(cursor left/right) to adjust the volume of the
speaker you selected to match the reference speaker.
When it sounds like both tones are the same volume,
press
ENTER
to confirm and continue to the next
channel.
For comparison purposes, the reference speaker will
change depending on which speaker you select.
If you want to go back and adjust a channel, simply
use
/
(cursor up/down) to select it.
4 When you're finished, press RETURN.
You will return to the Manual MCACC setup menu.
Fine Channel Distance
Default setting:
2.0 m
(all channels)
For proper sound depth and separation with your system,
it is necessary to add a slight bit of delay to some
speakers so that all sounds will arrive at the listening
position at the same time. The following setting can help
you make detailed adjustments that you may not achieve
using the
Manual speaker setup
below.
1 Select Fine Ch Distance from the Manual
MCACC setup menu.
2 Adjust the distance of the left channel from the
listening position.
3 Select each channel in turn and adjust the
distance as necessary.
Use
/
(cursor left/right) to adjust the delay of the
speaker you selected to match the reference speaker.
The delay is measured in terms of speaker distance from
0.1
to
9.0
meters.
Listen to the reference speaker and use it to measure the
target channel. From the listening position, face the two
speakers with your arms outstretched pointing at each
speaker. Try to make the two tones sound as if they are
arriving simultaneously at a position slightly in front of
you and between your arm span.
3.MANUAL MCACC
[ a .Fine Ch Level ]
[ b .Fine Ch Distance ]
[ c .EQ AUTO Setting ]
[ d .EQ Data Copy ]
[ e .EQ CUSTOM1 Adjust ]
[ f .EQ CUSTOM2 Adjust ]
[ g .EQ Data Check ]
3a.Fine Channel Level
Please Wait
Caution!!
Test tone is
output loudly.
Return:Cancel
3a.Fine Channel Level
Left [ + 0.5dB ]
Enter:Next
Return:Cancel
3a.Fine Channel Level
Ref:Left + 0.5dB
Right [ + 1.0dB ]
Center [ 0.0dB ]
Surround L [ 0.0dB ]
Surround R [ 0.0dB ]
Surr Back L [ 0.0dB ]
Surr Back R [ 0.0dB ]
Sub Woofer [ 0.0dB ]
Return:Finish
3.MANUAL MCACC
[ a .Fine Ch Level ]
[ b .Fine Ch Distance ]
[ c .EQ AUTO Setting ]
[ d .EQ Data Copy ]
[ e .EQ CUSTOM1 Adjust ]
[ f .EQ CUSTOM2 Adjust ]
[ g .EQ Data Check ]
3b.Fine Channel Distance
Please Wait
Caution!!
Test tone is
output loudly.
Return:Cancel
3b.Fine Channel Distance
Left [ 2.0 m ]
Enter:Next
Return:Cancel
3b.Fine Channel Distance
Ref:Left 2.0 m
Right [ 2.0 m ]
Center [ 2.0 m ]
Surround L [ 2.0 m ]
Surround R [ 2.0 m ]
Surr Back L [ 2.0 m ]
Surr Back R [ 2.0 m ]
Sub Woofer [ 2.0 m ]
Return:Finish
VSX_2014TX.book.fm 40
The System Setup menu 06
41
En
When it sounds like the delay settings are matched up,
press
ENTER
to confirm and continue to the next
channel.
For comparison purposes, the reference speaker will
change depending on which speaker you select.
If you want to go back and adjust a channel, simply
use
/
(cursor up/down) to select it.
4 When you're finished, press RETURN.
You will return to the Manual MCACC setup menu.
Acoustic Calibration EQ
Acoustic Calibration Equalization is a kind of room
equalizer for your speakers (excluding the subwoofer). It
works by measuring the acoustic characteristics of your
room and neutralizing the ambient characteristics that
can color the original source material. This provides a
flat equalization setting. If youre not satisfied with the
automatic adjustment, you can also adjust these settings
manually to get a frequency balance that suits your
tastes.
Setting the Acoustic Calibration EQ automatically
If you have already completed
Automatically setting up for
surround sound (MCACC)
on page 11,
ALL CH ADJUST
and
FRONT ALIGN
(below) should already be set.
Therefore, if you want to adjust your settings manually,
you can skip to
Setting the Acoustic Calibration EQ
manually
below.
1 Select EQ AUTO Setting from the Manual
MCACC setup menu.
Make sure the microphone is connected.
If youre using a subwoofer, it is automatically
detected every time you switch on the system. Make
sure it is on and the volume is at the middle position.
See
Other problems when using the Auto MCACC
Setup
on page 13 for notes regarding high
background noise levels and other possible
interference.
2 Wait for the Auto MCACC Setup to finish.
As the receiver outputs test tones, the frequency balance
is adjusted automatically for the following settings:
ALL CH ADJUST
A flat setting where all the
speakers are set individually so no special weighting
is given to any one channel.
FRONT ALIGN
All speakers are set in accordance
with the front speaker settings (no equalization is
applied to the front left and right channels).
You will return to the Acoustic Cal EQ setup menu after
the Acoustic Calibration Equalization is set.
Copying your Acoustic Calibration EQ settings
If you want to manually adjust the Acoustic Calibration
EQ (see
Setting the Acoustic Calibration EQ manually
below), we recommend copying the
ALL CH ADJUST
or
the
FRONT ALIGN
settings from the
EQ AUTO
setup
above (or from
Automatically setting up for surround
sound (MCACC)
on page 11) to one of the custom
settings. Instead of just a flat EQ curve, this will give you
a reference point from which to start.
1 Select EQ Data Copy from the Manual MCACC
setup menu.
2 Select CUSTOM1 or CUSTOM2 then use the
/
(cursor left/right) buttons to select the setting you
want to copy.
You can also copy from one custom setting to
another. For more on the
ALL CH ADJUST
and
FRONT ALIGN
settings, see
Setting the Acoustic
Calibration EQ automatically
above.
3.MANUAL MCACC
[ a .Fine Ch Level ]
[ b .Fine Ch Distance ]
[ c .EQ AUTO Setting ]
[ d .EQ Data Copy ]
[ e .EQ CUSTOM1 Adjust ]
[ f .EQ CUSTOM2 Adjust ]
[ g .EQ Data Check ]
3c.EQ AUTO Setting
Please Wait
Caution!!
Test tone is
output loudly.
Return:Cancel
3c. EQ AUTO Setting
Now Analyzing
Environment Check
Ambient Noise [ ]
Microphone [ ]
Speaker YES/NO [ ]
Return:Cancel
3c. EQ AUTO Setting
Now Analyzing
Surround Analyzing
Channel Level [ ]
Acoustic Cal EQ [ ]
Return:Cancel
3.MANUAL MCACC
[ a .Fine Ch Level ]
[ b .Fine Ch Distance ]
[ c .EQ AUTO Setting ]
[ d .EQ Data Copy ]
[ e .EQ CUSTOM1 Adjust ]
[ f .EQ CUSTOM2 Adjust ]
[ g .EQ Data Check ]
3d. EQ Data Copy
TO FROM
CUSTOM1 [ CUSTOM1 ]
CUSTOM2 [ CUSTOM2 ]
Start Copy [ OK ]
3d. EQ Data Copy
TO FROM
CUSTOM1 [ ALL CH ADJ. ]
CUSTOM2 [ CUSTOM2 ]
Start Copy [ OK ]
VSX_2014TX.book.fm 41
The System Setup menu 06
42
En
3 Select OK to copy and confirm.
Setting the Acoustic Calibration EQ manually
Before manually adjusting the Acoustic Calibration EQ,
we recommend copying the
ALL CH ADJUST
or the
FRONT ALIGN
settings from the auto setup above (or
from
Automatically setting up for surround sound
(MCACC)
on page 11) to one of the custom settings.
Instead of just a flat EQ curve, this will give you a
reference point from which to start (see
Copying your
Acoustic Calibration EQ settings
above for how to do this).
1 Select EQ CUSTOM1 Adjust or EQ CUSTOM2
Adjust from the Manual MCACC setup menu.
2 Select which method you would like to use to
adjust the overall frequency balance.
It is best to choose whichever one you copied to the
custom setting in
Copying your Acoustic Calibration EQ
settings
above.
ALL CH ADJUST
All the speakers can be set
independently so no special weighting is given to any
one channel. When adjusting, test tones will sound
for each individual channel.
FRONT ALIGN
Speakers are set in accordance with
the front speaker settings. The sound of the test tone
will alternate between the left front (reference)
speaker and the target speaker.
3 Select the channel(s) you want and adjust to
your liking.
Use the
/
(cursor left/right) buttons to select the
channel.
Use the
/
(cursor up/down) buttons to select the
frequency and
/
(cursor left/right) to boost or cut the
EQ. When youre finished, go back to the top of the
screen and use the
/
(cursor left/right) buttons to
select the next channel.
The front speakers cant be adjusted if you selected
FRONT ALIGN
.
The
OVER
indicator shows in the display if the
frequency adjustment is too drastic and might
distort. If this happens, bring the level down until
OVER
disappears from the display.
Tip
Changing the frequency curve of one channel too
drastically will affect the overall balance. If the
speaker balance seems uneven, you can raise or
lower channel levels using test tones with the
TRIM
feature. Use
/
(cursor up/down) to select
TRIM
then use
/
(cursor left/right) to raise or lower the
channel level for the current speaker.
4 When you're finished, press RETURN.
You will return to the Manual MCACC setup menu.
Checking your Acoustic Calibration EQ settings
After you have completed an automatic or manual
Acoustic Calibration EQ adjustment, you can check the
ALL CH ADJUST
,
FRONT ALIGN
and custom settings
using the on-screen display.
1 Select EQ Data Check from the Manual MCACC
setup menu.
3d. EQ Data Copy
TO FROM
CUSTOM1 [ ALL CH ADJ. ]
CUSTOM2 [ CUSTOM2 ]
Start Copy [ OK ]
Enter :Start Copy
3.MANUAL MCACC
[ a .Fine Ch Level ]
[ b .Fine Ch Distance ]
[ c .EQ AUTO Setting ]
[ d .EQ Data Copy ]
[ e .EQ CUSTOM1 Adjust ]
[ f .EQ CUSTOM2 Adjust ]
[ g .EQ Data Check ]
3e. EQ CUSTOM1 Adjust
Test Tone Type
[ ALL CH ADJUST ]
Enter : Next
Return : Cancel
3e. EQ CUSTOM1 Adjust
Test Tone Type:
"ALL CH ADJUST"
[ Left EQ ]
40Hz : [+ 1.0dB ]
125Hz : [ 0.0dB ]
250Hz : [ 0.0dB ]
4kHz : [ 0.0dB ]
13kHz : [ 0.0dB ]
TRIM : [ 0.0dB ]
3f. EQ CUSTOM2 Adjust
Test Tone Type:
"ALL CH ADJUST"
[ Left EQ ]
40Hz : [ 0.0dB ]
125Hz : [ 0.0dB ]
250Hz : [ 0.0dB ]
4kHz : [ 0.0dB ]
13kHz : [ 0.0dB ]
TRIM : [ 0.0dB ]
3.MANUAL MCACC
[ a .Fine Ch Level ]
[ b .Fine Ch Distance ]
[ c .EQ AUTO Setting ]
[ d .EQ Data Copy ]
[ e .EQ CUSTOM1 Adjust ]
[ f .EQ CUSTOM2 Adjust ]
[ g .EQ Data Check ]
VSX_2014TX.book.fm 42
The System Setup menu 06
43
En
2 Select the setting you want to check.
It is useful to do this while a source is playing so you
can compare the different settings.
3 Select the channels you want, pressing ENTER
when youre finished checking each one.
4 When you're finished, press RETURN.
You will return to the Manual MCACC setup menu.
Manual speaker setup
This receiver allows you to make detailed settings to
optimize the surround sound performance. You only
need to make these settings once (unless you change the
placement of your current speaker system or add new
speakers).
These settings are designed to fine-tune your system, but
if youre satisfied with the settings made in
Automatically
setting up for surround sound (MCACC)
on page 11, it
isnt necessary to make all of these settings.
Caution
The test tones used in the System Setup are output at
high volume (the volume increases to 0dB
automatically).
1 Select Manual SP Setup then press ENTER.
2 Select the setting you want to adjust.
If you are doing this for the first time, you may want to
adjust these settings in order:
Speaker Setting
Specify the size and number of
speakers youve connected (page 44).
Crossover Network
Specify which frequencies will
be sent to the subwoofer (see
Crossover Network
below).
Channel Level
Adjust the overall balance of your
speaker system (page 45).
Speaker Distance
Specify the distance of your
speakers from the listening position (page 46).
3 Make the adjustments necessary for each
setting, pressing RETURN to confirm after each
screen.
3g. EQ Data Check
Type [ ALL CH ADJUST ]
Ch [ Left EQ]
40Hz : 0.0dB
125Hz : 0.0dB
250Hz : 0.0dB
4kHz : 0.0dB
13kHz : 0.0dB
TRIM : 0.0dB
3g. EQ Data Check
Type [ ALL CH ADJUST ]
Ch [ Left EQ]
40Hz : 0.0dB
125Hz : 0.0dB
250Hz : 0.0dB
4kHz : 0.0dB
13kHz : 0.0dB
TRIM : 0.0dB
3g. EQ Data Check
Type [ ALL CH ADJUST ]
Ch [ Left EQ]
40Hz : 0.0dB 0.0dB
125Hz : 0.0dB
250Hz : 0.0dB
4kHz : 0.0dB
13kHz : 0.0dB
TRIM : 0.0dB System Setup
[ 1 . Surr Back System ]
[ 2 . AUTO MCACC ]
[ 3 . MANUAL MCACC ]
[ 4 . Manual SP Setup ]
[ 5 . Input Assign ]
[ 6 . Other Setup ]
Enter : Select
Return : Exit
4. Manual SP Setup
[ a . Speaker Setting ]
[ b . Crossover Network ]
[ c . Channel Level ]
[ d . Speaker Distance ]
VSX_2014TX.book.fm 43
The System Setup menu 06
44
En
Speaker Setting
Use this setting to specify your speaker configuration
(size, number of speakers). It is a good idea to make sure
that the settings made in
Automatically setting up for
surround sound (MCACC)
on page 11 are correct.
1 Select Speaker Setting from the Manual SP
Setup menu.
2 Choose the set of speakers that you want to set
then select a speaker size.
Use
/
(cursor left/right) to select the size (and
number) of each of the following speakers:
Front
Select
LARGE
if your front speakers
reproduce bass frequencies effectively, or if you
didnt connect a subwoofer. Select
SMALL
to send
the bass frequencies to the subwoofer.
Center
Select
LARGE
if your center speaker
reproduces bass frequencies effectively, or select
SMALL
to send bass frequencies to the other
speakers or subwoofer. If you didnt connect a center
speaker, choose
NO
(the center channel is sent to
the front speakers).
Surround
Select
LARGE
if your surround speakers
reproduce bass frequencies effectively. Select
SMALL
to send bass frequencies to the other
speakers or subwoofer. If you didnt connect
surround speakers choose
NO
(the sound of the
surround channels is sent to the front speakers or a
subwoofer).
Surr Back
Select the number of surround back
speakers you have (one, two or none). Select
LARGE
if your surround back speakers reproduce bass
frequencies effectively. Select
SMALL
to send bass
frequencies to the other speakers or subwoofer. If
you didnt connect surround back speakers choose
NO
.
Subwoofer
LFE signals and bass frequencies of
channels set to
SMALL
are output from the
subwoofer when
YES
is selected (see notes below).
Choose the
PLUS
setting if you want the subwoofer to
output bass sound continuously or you want deeper
bass (the bass frequencies that would normally come
out the front and center speakers are also routed to
the subwoofer). If you did not connect a subwoofer
choose
NO
(the bass frequencies are output from
other speakers).
Note
If you selected
Second Zone
or
Front Bi-Amp
(in
Surround back speaker setting
on page 38) you cant
adjust the surround back settings.
If you select
SMALL
for the front speakers the
subwoofer will automatically be fixed to
YES
. Also,
the center and surround speakers cant be set to
LARGE
if the front speakers are set to
SMALL
. In this
case, all bass frequencies are sent to the subwoofer.
If the surround speakers are set to
NO
, the surround
back speakers will automatically be set to
NO
.
If you select one surround back speaker only, make
sure that speaker is hooked up to the left surround
back terminal.
If youre using a THX speaker setup, confirm that all
speakers are set to
SMALL
.
3 When youre finished, press RETURN.
You will return to the Manual SP Setup menu.
Tip
If you have a subwoofer and like lots of bass, it may
seem logical to select
LARGE
for your front speakers
and
PLUS
for the subwoofer. This may not, however,
yield the best bass results. Depending on the speaker
placement of your room you may actually experience
a decrease in the amount of bass due low frequency
cancellations. In this case, try changing the position
or direction of speakers. If you cant get good results,
listen to the bass response with it set to
PLUS
and
YES
or the front speakers set to
LARGE
and
SMALL
alternatively and let your ears judge which sounds
best. If youre having problems, the easiest option is
to route all the bass sounds to the subwoofer by
selecting
SMALL
for the front speakers.
4. Manual SP Setup
[ a . Speaker Setting ]
[ b . Crossover Network ]
[ c . Channel Level ]
[ d . Speaker Distance ]
4a. Speaker Setting
Front [ LARGE ]
Center [ SMALL ]
Surround [ SMALL ]
Surr Back [ SMALLx2 ]
Sub Woofer [ YES ]
(THX Speaker:SMALL)
VSX_2014TX.book.fm 44
The System Setup menu 06
45
En
Crossover Network
Default setting:
80Hz
This setting decides the cutoff between bass sounds
playing back from the speakers selected as
LARGE
, or
the subwoofer, and bass sounds playing back from those
selected as
SMALL
. It also decides where the cutoff will
be for bass sounds in the LFE channel.
Note
For more on selecting the speaker sizes, see
Speaker
Setting
above.
1 Select Crossover Network from the Manual SP
Setup menu.
2 Choose the frequency cutoff point.
Frequencies below the cutoff point will be sent to the
subwoofer (or
LARGE
speakers).
3 When youre finished, press RETURN.
You will return to the Manual SP Setup menu.
Note
If youre using a THX speaker setup, confirm that the
crossover frequency is set to
80Hz
.
Channel Level
Using the channel level settings, you can adjust the
overall balance of your speaker system, an important
factor when setting up a home theater system.
1 Select Channel Level from the Manual SP Setup
menu.
2 Select a setup option.
Manual
Move the test tone manually from speaker
to speaker and adjust individual channel levels.
Auto
Adjust channel levels as the test tone moves
from speaker to speaker automatically.
3 Confirm your selected setup option.
The test tones will start after you press
ENTER
.
4 Adjust the level of each channel using the
/
(cursor left/right) buttons.
If you selected
Manual
, use
/
(cursor up/down) to
switch speakers. The
Auto
setup will output test tones in
the order shown on-screen:
Adjust the level of each speaker as the test tone is
emitted.
4. Manual SP Setup
[ a . Speaker Setting ]
[ b . Crossover Network ]
[ c . Channel Level ]
[ d . Speaker Distance ]
4b. Crossover Network
Frequency [ 80Hz ]
(THX Speaker = 80Hz)
4. Manual SP Setup
[ a . Speaker Setting ]
[ b . Crossover Network ]
[ c . Channel Level ]
[ d . Speaker Distance ]
4c. Channel Level
Test Tone [ [ Auto ] ]
Enter : Next
Return : Cancel
4c. Channel Level
Test Tone [ Manual ]
Enter : Next
Return : Cancel
4c. Channel Level
Test Tone [ Manual ]
Setting Start
Please Wait
Caution!!
Test tone is
output loudly.
Return:Cancel
4c. Channel Level
Left [ + 0.5dB]
Center [ 0.0dB]
Right [ 0.0dB]
Surround R [ 0.0dB]
Surr Back R [ 0.0dB]
Surr Back L [ 0.0dB]
Surround L [ 0.0dB]
Sub Woofer [ 0.0dB]
Return:Finish
VSX_2014TX.book.fm 45
The System Setup menu 06
46
En
Note
If you are using a Sound Pressure Level (SPL) meter,
take the readings from your main listening position
and adjust the level of each speaker to 75 dB SPL (C-
weighting/slow reading).
The subwoofer test tone is output at low volumes. You
may need to adjust the level after testing with an
actual soundtrack.
5 When youre finished, press RETURN.
You will return to the Manual SP Setup menu.
Tip
You can change the channel levels at any time by
using
EFFECT/CH SEL
and
+/
on the remote control.
You can set separate levels for the listening modes
(Standard, Home THX, Advanced and Stereo/Direct)
as well as for the
MULTI CH IN
mode. However, the
listening mode setting will be cleared if you use one
of the setups (for example, the System Setup or Auto
Setup) to set the channel levels at a later date.
Speaker Distance
For good sound depth and separation from your system,
you need to specify the distance of your speakers from
the listening position. The receiver can then add the
proper delay needed for effective surround sound.
1 Select Speaker Distance from the Manual SP
Setup menu.
2 Adjust the distance of each speaker using the
/
(cursor left/right) buttons.
You can adjust the distance of each speaker in 0.1 meter
increments.
3 When youre finished, press RETURN.
You will return to the Manual SP Setup menu.
Tip
For best surround sound, make sure the surround
back speakers are the same distance from the
listening position.
4. Manual SP Setup
[ a. Speaker Setting ]
[ b. Crossover Network ]
[ c. Channel Level ]
[ d. Speaker Distance ]
4d. Speaker Distance
Left [ 2.0 m ]
Center [ 2.0 m ]
Right [ 2.0 m ]
Surround R [ 2.0 m ]
Surr Back R [ 2.0 m ]
Surr Back L [ 2.0 m ]
Surround L [ 2.0 m ]
Sub Woofer [ 2.0 m ]
VSX_2014TX.book.fm 46
Using the tuner 07
47
En
Chapter 7:
Using the tuner
Listening to the radio
The following steps show you how to tune in to FM and
AM radio broadcasts using the automatic (search) and
manual (step) tuning functions. If you already know the
frequency of the station you want, see
Tuning directly to a
station
below. Once you are tuned to a station you can
memorize the frequency for recall latersee
Saving
station presets
on page 48 for more on how to do this.
1 Press the TUNER button to select the tuner.
2 Use the BAND button to change the band (FM or
AM), if necessary.
Each press switches the band between FM and AM.
3 Tune to a station.
There are three ways to do this:
Automatic tuning
To search for stations in the currently selected band,
press and hold
TUNE +/
for about a second. The
receiver will start searching for the next station,
stopping when it has found one. Repeat to search for
other stations.
Manual tuning
To change the frequency one step at a time, press
TUNE +/
.
High speed tuning
Press and hold
TUNE +/
for high speed tuning.
Release the button at the frequency you want.
Improving FM stereo sound
If the
TUNED
or
STEREO
indicators don't light when
tuning to an FM station because the signal is weak, press
the
MPX
button to switch the receiver into mono
reception mode. This should improve the sound quality
and allow you to enjoy the broadcast.
Tuning directly to a station
Sometimes, you'll already know the frequency of the
station you want to listen to. In this case, you can simply
enter the frequency directly using the number buttons on
the remote control.
1 Press the TUNER button to select the tuner.
2 Use the BAND button to change the band (FM or
AM), if necessary.
Each press switches the band between FM and AM.
3 Press D.ACCESS (Direct Access).
4 Use the number buttons to enter the frequency
of the radio station.
For example, to tune to
106.00
(FM), press
1
,
0
,
6
,
0
,
0
.
If you make a mistake halfway through, press
D.ACCESS
twice to cancel the frequency and start over.
Note
If you find that you cant tune into stations
successfully, the frequency step may not be suitable
for your country/region. See
Changing the frequency
step
on page 76 to switch the setting.
+10
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
ENTER
TV CONTROL
RECEIVERCONTROL
SHIFT
VOL
DVD/LD TV/SAT DVR/VCR TVCONT
CD
TUNE
ST ST
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
INPUT
SELECT
TV CH
DTVON/OFF
TUNER
DISPLAY
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
DTVINFO REC MUTE
TVVOL
CD-R/TAPE TUNER RECEIVER
ENTER
RECSTOP
HDD
CH CH
DVD
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
TUNE
RECEIVER
VSX_2014TX.book.fm 47
Using the tuner 07
48
En
Saving station presets
If you often listen to a particular radio station, it's
convenient to have the receiver store the frequency for
easy recall whenever you want to listen to that station.
This saves the effort of manually tuning in each time. This
unit can memorize up to 30 stations, stored in three
banks, or classes, (A, B and C) of 10 stations each. When
saving an FM frequency, the
MPX
setting (see page 47) is
also stored.
The illustration above shows the VSX-2014i-G model.
1 Tune to a station you want to memorize.
See
Listening to the radio
on page 47 for more on this.
2 Press T.EDIT (TUNER EDIT).
The display shows
STATION MEMORY
, then a blinking
memory class.
3 Press CLASS to select one of the three classes
then press ST +/ (STATION +/) to select the station
preset you want.
You can also use the number buttons or the
MULTI JOG
dial (front panel) to select a station preset.
4 Press ENTER.
After pressing
ENTER
, the preset class and number stop
blinking and the receiver stores the station.
Naming station presets
For easier identification, you can name your station
presets.
1 Choose the station preset you want to name.
See
Listening to station presets
below for how to do this.
2 Press T.EDIT (TUNER EDIT).
The display shows
STATION NAME
, then a blinking
cursor at the first character position.
3 Input the name you want.
Choose from the following characters for a name up to
four characters long.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
0123456789
!#$%&()
+,./:;<=>?@[ \ ]^_{|}
Use the
MULTI JOG
dial (front panel) or the
ST +/
buttons (remote) to select characters.
Press
ENTER
to confirm a character. If no character
is input, a space is input.
The name is stored when
ENTER
is pressed after
choosing the fourth character.
Tip
To erase a station name, simply repeat steps 1-3 and
input four spaces instead of a name.
Once you have named a station preset, you can press
TUNER
DISPLAY
when listening to a station to
switch the display between name and frequency.
Listening to station presets
You will need to have some presets stored to do this. See
Saving station presets
above if you havent done this
already.
1 Press TUNER to select the tuner.
2 Press CLASS to select the class in which the
station is stored.
Press repeatedly to cycle through classes A, B and C.
3 Press ST +/ (STATION +/) to select the station
preset you want.
You can also use the number buttons on the remote
control to recall the station preset.
Note
If the receiver is left disconnected from the AC power
outlet for over a month, the station memories will be
lost and will have to be reprogrammed.
STANDBY/ON
MULTI JOG
LISTENING MODE
SELECT
ENTER
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
DVD/LD TV/SAT DVR/VCR TVCONT
CD CD-R/TAPE TUNER RECEIVER
+10
INPUT ATT FLDIMMER SR
DISC
ENTER
TV CONTROL
VOL
TUNE
TUNE
INPUT
SELECT
TV CH
DTVON/OFF
TUNER
DISPLAY
MPX
AUDIO
CHRETURN
SUBTITLE
DTVINFO REC MUTE
TVVOL
ENTER
RECSTOP
HDD
CH CH
DVD
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
ST ST
VSX_2014TX.book.fm 48
Making recordings 08
49
En
Chapter 8:
Making recordings
Making an audio or a video recording
You can make an audio or a video recording from the
built-in tuner, or from an audio or video source
connected to the receiver (such as a CD player or TV).
Keep in mind you cant make a digital recording from an
analog source or vice-versa, so make sure the
components you are recording to/from are hooked up in
the same way (see
Connecting up
on page 14 for more on
connections).
If you want to record a video source, you also need to use
the same type of connection for the source as for the
recorder. For example, you cant record a component
hooked up to S-video jacks with a recorder hooked up to
the composite video outputs (see page 18 for more on
video connections).
The illustration above shows the VSX-2014i-G model.
1 Select the source you want to record.
Use the
MULTI CONTROL
buttons (or
INPUT SELECT
).
2 Select the input signal (if necessary).
Press
SIGNAL SELECT
to select the input signal
corresponding to the source component (see page 33 for
more on this).
3 Prepare the source you want to record.
Tune to the radio station, load the CD, video, DVD etc.
4 Prepare the recorder.
Insert a blank tape, MD, video etc. into the recording
device and set the recording levels.
Refer to the instructions that came with the recorder if
you are unsure how to do this. Most video recorders set
the audio recording level automaticallycheck the
components instruction manual if youre unsure.
5 Start recording, then start playback of the source
component.
Note
The receiver's volume, balance, tone (bass, treble,
loudness), and surround effects have no effect on the
recorded signal.
Some digital sources are copy-protected, and can
only be recorded in analog.
Some video sources are copy-protected. These
cannot be recorded.
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
DVD/LD TV/SAT DVR/VCR TVCONT
CD CD-R/TAPE TUNER RECEIVER
RECEIVERCONTROL
SHIFT
VOL
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
INPUT
SELECT
TV CH
DTVON/OFF
TUNER
DISPLAY
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
DTVINFO REC MUTE
TVVOL
RECSTOP
HDD
CH CH
DVD
RECEIVER
MASTER VOLUME
DVD/LD TV/SAT DVR/VCR VIDEO1
CD
CD-R/
TAPE/MD TUNER VIDEO2
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
VSX_2014TX.book.fm 49
Controlling the rest of your system 09
50
En
Chapter 9:
Controlling the rest of your system
Setting the remote to control other
components
Most components can be assigned to one of the
MULTI
CONTROL
buttons using the components manufacturer
preset code stored in the remote.
However, please note that there are cases where only
certain functions may be controllable after assigning the
proper preset code, or the codes for the manufacturer in
the remote control will not work for the model that you
are using.
If you cant find a preset code that matches the
component you want to control, you can still teach the
remote individual commands from another remote
control (page 51).
Note
TV codes (for example, codes for TV, CATV, Satellite
TV or DTV) can only be assigned to the
TV/SAT
or
TV
CONT
button.
If you assign the
TUNER
function to another
component, you will have to reassign it to the Pioneer
preset code to use this receivers built-in tuner.
You can cancel or exit any of the steps by pressing
RECEIVER
. To go back a step, press
RETURN
.
After one minute of inactivity, the remote
automatically exits the operation.
Selecting preset codes directly
1 While pressing the RECEIVER button, press and
hold the 1 button.
The remote LCD display shows
SETUP
.
2 Press the MULTI CONTROL button for the
component you want to control.
The LCD on the remote displays the component you want
to control.
You cant assign the
RECEIVER
button.
3 Use
+/~
(cursor left/right) to select PRESET
then press ENTER.
4 Use
/
(cursor up/down) to select the first
letter of the brand name of your component then
press ENTER.
This should be the manufacturers name (for example,
P
for Pioneer).
5 Use
/
(cursor up/down) to select the
manufacturers name from the list then press ENTER.
6 Use
/
(cursor up/down) to select the proper
code from the list, then try using this remote control
with your component.
The code should start with the component type (for
example,
DVD 009
). If there is more than one, start with
the first one.
To try out the remote control, switch the component on or
off (into standby) by pressing
SOURCE
C
. If it doesnt
seem to work, select the next code from the list (if there
is one).
If you cant find or properly enter a preset code, you
can still teach the remote individual commands from
another remote control (see
Programming signals
from other remote controls
below).
7 If your component is controlled successfully,
press ENTER to confirm.
The remote LCD display shows
OK
.
+10
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
ENTER
TV CONTROL
VOL
DVD/LD TV/SAT DVR/VCR TVCONT
CD
TUNE
TUNE
ST ST
INPUT
SELECT
TV CH TVVOL
CD-R/TAPE TUNER RECEIVER
ENTER
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
!
09_controlling_system.fm 50
Controlling the rest of your system 09
51
En
Programming signals from other
remote controls
If the preset code for your component is not available, or
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
assigning a preset code.
1 While pressing the RECEIVER button, press and
hold the 1 button.
The remote LCD display shows
SETUP
.
2 Press the MULTI CONTROL button for the
component you want to control.
The LCD on the remote displays the component you want
to control.
You cant assign the
RECEIVER
button.
3 Use
+/~
(cursor left/right) to select LEARN then
press ENTER.
PRES KEY
shows in the LCD display.
To exit or cancel press
RECEIVER
.
4 Point the two remote controls towards each
other then press the button that will be doing the
learning on this receivers remote control.
PRES KEY
starts flashing to indicate the remote is ready
to accept a signal.
The remote controls should be 35 cm apart.
5 Press the corresponding button on the other
remote control that is sending (teaching) the signal
to this receivers remote control.
For example, if you want to learn the playback control
signal, press and hold
>
for a couple of seconds. The
LCD display will show
OK
if the operation has been
learned.
If for some reasons the operation hasnt been learned the
LCD will display
ERROR
briefly and then display
PRES
KEY
again. If this happens, keep pressing the (teaching)
button as you vary the distance between the two remotes,
until the LCD display shows
OK
.
Certain buttons represent operations that cannot be
learned from other remote controls. The buttons
available are shown below:
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
7 Press the RECEIVER button to exit and store the
operation(s).
Note
Some commands from other remote controls cannot
be learned, but in most cases the remotes just need
to be moved closer together or farther apart.
If the remote LCD shows
ERROR
, it may also mean
the memory is full. See
Erasing one of the remote
control button settings
below to erase a programmed
button youre not using to free up more memory.
TV CONTROL
buttons (
TV
C
,
TV VOL +/
,
TV CH +/
and
INPUT SELECT
) can only be learned after
selecting
TV CONT
.
3 5 cm
+10
INPUT ATT
FL DIMMER
SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECTSETUP
ENTER
TV CONTROL
RECEIVER CONTROL
SHIFT
VOL
DVD/LD
TV/SAT
DVR/VCR
TV CONT
CD
TUNETUNE
ST
ST
STANDRAD
LEVEL
EFFECT
TEST TONE
CH SELECT
ADV. SURR
STEREO
SLEEP
INPUT
SELECT
TV CH
DTV ON/OFF
TUNER
DISPLAY
MPX
AUDIO
CH RETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
DTV INFO
REC
MUTE
TV VOL
CD-R/TAPE
TUNER
RECEIVER
ENTER
REC STOP
HDDCH
CH DVD
D.ACCESS
TOP MENU
DTV MENU
CLASS
MENU
BAND
RETURN
GUIDE
T.EDIT
MCACC
SETUP
RECEIVER
+10
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
ENTER
TV CONTROL
RECEIVERCONTROL
SHIFT
VOL
DVD/LD TV/SAT DVR/VCR TVCONT
CD
ST ST
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
INPUT
SELECT
TV CH
DTVON/OFF
TUNER
DISPLAY
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
DTVINFO REC MUTE
TVVOL
CD-R/TAPE TUNER RECEIVER
ENTER
RECSTOP
HDD
CH CH
DVD
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
RECEIVER
TUNE
TUNE
!
09_controlling_system.fm 51
Controlling the rest of your system 09
52
En
Erasing one of the remote control
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
1 While pressing the RECEIVER button, press and
hold the 1 button.
The remote LCD display shows
SETUP
.
2 Press the MULTI CONTROL button corresponding
to the button setting to be erased.
The LCD on the remote displays the component.
3 Use
+/~
(cursor left/right) to select ERASE then
press ENTER.
The LCD display flashes
PRES KEY
.
4 Press and hold the button to be erased for two
seconds.
The LCD display shows
OK
or
NO CODE
to confirm the
button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press the RECEIVER button when youre done.
Erasing all of the remote control
presets
This will erase all preset remote control preset codes and
programmed buttons.
1 While pressing the RECEIVER button, press and
hold the 1 button.
The remote LCD display shows
SETUP
.
2 Press the DVD/LD MULTI CONTROL button.
3 Use
+/~
(cursor left/right) to select RESET then
press and hold ENTER for about two seconds.
The LCD shows
OK
to confirm the remote presets have
been erased.
Direct function
Default setting:
ON
You can use the direct function feature to control one
component using the remote control while at the same
time, using your receiver to playback a different
component. This could let you, for example, use the
remote control to set up and listen to a CD on the receiver
and then use the remote control to rewind a tape in your
VCR while you continue to listen to your CD player.
When direct function is on, any component you select
(using the
MULTI CONTROL
buttons) will be selected by
both the receiver and the remote control. When you turn
direct function off, you can operate the remote control
without affecting the receiver.
1 While pressing the RECEIVER button, press and
hold the 1 button.
The remote LCD display shows
SETUP
.
2 Press the MULTI CONTROL button for the
component you want to control.
The LCD on the remote displays the component you want
to control.
3 Use
+/~
(cursor left/right) to select DIRECT F
then press ENTER.
The LCD on the remote displays the component you want
to control.
4 Use
/
(cursor up/down) to switch direct
function ON or OFF then press ENTER.
The LCD shows
OK
to confirm the setting.
Note
You cant use direct function with the
TV CONT
function.
Confirming preset codes
Use this feature to check which preset code is assigned
to a
MULTI CONTROL
button.
1 While pressing the RECEIVER button, press and
hold the 1 button.
The remote LCD display shows
SETUP
.
2 Press the MULTI CONTROL button of the
component for which you want to check the preset
code.
3 Use
+/~
(cursor left/right) to select READ ID
then press ENTER.
The brand name and preset code appears in the display
for three seconds.
09_controlling_system.fm 52
Controlling the rest of your system 09
53
En
Controls for TVs
This remote control can control components after entering the proper codes or teaching the receiver the commands
(see
Setting the remote to control other components
on page 50 for more on this). Use the
MULTI CONTROL
buttons
to select the component.
Note
The
TV CONTROL
buttons on the remote control are dedicated to control the TV assigned to the
TV CONT
button.
Thus if you only have one TV to hook up to this system assign it to the
TV CONT
(
MULTI CONTROL
) button. If you
have two TVs, assign the main TV to the
TV CONT
button.
Button(s) Function Components
TV
C
Press to switch the component assigned to the
TV CONT
button on or off.
Cable TV/Satellite TV/TV/DTV
INPUT
SELECT
Switches the TV input. (Not possible with all models.) TV
TV CH +/
Selects channels. Cable TV/Satellite TV/TV/DTV
TV VOL +/
Adjust the TV volume. Cable TV/Satellite TV/TV/DTV
SOURCE
C
Switches the DTV on or off. DTV
Switches the TV or CATV between standby and on. Cable TV/Satellite TV/TV
Switches the DTV on or off. DTV
>
Press to get information on DTV programs. DTV
m
Use to choose the BLUE commands on a DTV menu. DTV
>
Use to choose the YELLOW commands on a DTV menu. DTV
H
Use to choose the GREEN commands on a DTV menu. DTV
N
Use to choose the RED commands on a DTV menu. DTV
AUDIO
Use to switch DTV audio tracks. DTV
CH RETURN
Use to return to the previously selected channel. Cable TV/Satellite TV/TV/DTV
DTV MENU
Press to display the DTV menu. DTV
GUIDE
Use as the
GUIDE
button for navigating. Cable TV/Satellite TV/TV/DTV
RETURN
Use to select
RETURN
or
EXIT
. DTV
Number
buttons
Use to select a specific TV channel. Cable TV/Satellite TV/TV/DTV
+10
button
Use to add a decimal point when selecting a specific TV channel. DTV
ENTER/
DISC
Use to enter a channel. Cable TV/Satellite TV/TV/DTV
MENU
Select different menus from the DTV functions. DTV
Select the menu screen. Cable TV/Satellite TV/TV
=_
&
ENTER
Press to select or adjust and navigate items on the menu screen. Cable TV/Satellite TV/TV/DTV
09_controlling_system.fm 53
Controlling the rest of your system 09
54
En
Controls for other components
This remote control can control these components after entering the proper codes or teaching the receiver the
commands (see
Setting the remote to control other components
on page 50 for more on this). Use the
MULTI
CONTROL
buttons to select the component.
Button (s) Function Components
SOURCE
C
Press to switch the component between standby and on. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
m
Press to return to the start of the current track or chapter.
Repeated presses skips to the start of previous tracks or chapters.
CD/MD/CD-R/DVD/LD player
Go back channels (channel ). DVR/VCR
>
Press to advance to the start of the next track or chapter.
Repeated presses skips to the start of following tracks or chapters.
CD/MD/CD-R/DVD/LD player
Go forward channels (channel +). VCR
H
Pause playback or recording. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
>
Start playback. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
>
Hold down for fast forward playback. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
Hold down for fast reverse playback. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
N
Stops playback (on some models, pressing this when the disc is already stopped will
cause the disc tray to open).
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
&
REC
(
SHIFT+
>
)
Starts recording. To prevent accidental recording, this button must be pressed twice to
take effect (the second press must be within 10 seconds of the first).
MD/CD-R/VCR/ DVR player/
Cassette deck
REC STOP
(
SHIFT+
N
)
Stops recording. DVR player
Number
buttons
Directly access tracks on a program source. CD/MD/CD-R/VCR/LD player
Use the number buttons to navigate the on-screen
display.
DVD/DVR player
+10
button
Selects tracks higher than 10. (For example, press
+10
then
3
to select track 13.) CD/MD/CD-R/VCR/LD player
ENTER/
DISC
Chooses the disc. Multiple CD player
Ejects the disc. MD player
Use as the
ENTER
button. VCR
Use as the
CLEAR
button. DVD
Displays the setup screen for DVR players. DVR player
Changes sides of the LD. LD player
TOP MENU
Displays the disc top menu of a DVD player. DVD/DVR player
MENU
Displays menus concerning the current DVD or DVR you are using. DVD/DVR player
Pauses the tape. Cassette deck
_
Stops the tape. Cassette deck
ENTER
Starts playback. Cassette deck
/=
Fast rewinds/fast forwards the tape. Cassette deck
=_
&
ENTER
Navigates DVD menu/options. DVD/DVR Player
GUIDE
Press to access the DVD player setup screen. DVD/DVR Player
CH +/
Selects channels. VCR/DVD/DVR Player
Selects tracks. CD/MD/CD-R/Cassette deck
AUDIO
Changes the audio language or channel. DVD/DVR Player
SUBTITLE
Displays/changes the subtitles on multilingual DVDs. DVD/DVR Player
HDD
(SHIFT+CH)
Switches to the hard disk controls when using a DVD/HDD recorder. DVR Player
DVD
(SHIFT+CH+)
Switches to the DVD controls when using a DVD/HDD recorder. DVR Player
09_controlling_system.fm 54
Other connections 10
55
En
Chapter 10:
Other connections
Caution
Before making or changing the connections
, switch off
the power and disconnect the power cord from the
power outlet. Plugging in components should be the
last connection you make with your system.
Be careful not to allow any contact between speaker
wires from different terminals.
You can use speakers with a nominal impedance
between 616
(please see
Switching the speaker
impedance
on page 76 if you plan to use speakers
with an impedance of less than 8
).
Second Zone speaker B setup
After selecting
Second Zone
in
Surround back speaker
setting
on page 38, you can use the speakers connected
to the (surround back) B speaker terminals on the rear
panel to listen to stereo playback in another room. See
Switching the speaker system
below for the listening
options with this setup.
1 Connect a pair of speakers to the surround back
speaker terminals on the rear panel.
Connect them the same way you connected your
speakers in
Connecting the speakers
on page 21. Make
sure to review
Hints on speaker placement
on page 22
when placing the speakers in another room.
2 Select Second Zone from the Surr Back System
menu.
See
Surround back speaker setting
on page 38 to do this.
Note
VSX-2014i-G model only
You can also use the multi-
room feature to listen to stereo playback in another
room. See
Multi-room listening
on page 57 for more
on this.
Switching the speaker system
If you selected
Second Zone
in
Surround back speaker
setting
on page 38, three speaker system settings are
possible using the
SPEAKERS
button. If you selected
Normal (SB)
or
Front Bi-Amp
, the button will simply
switch your main speaker system on or off. The options
below are for the
Second Zone
setting only.
Use the SPEAKERS button on the front panel to
select a speaker system setting.
As mentioned above, if you have selected
Normal (SB)
,
the button will simply switch your main speaker system
(A) on or off.
The illustration above shows the VSX-2014i-G model.
Press repeatedly to choose a speaker system option:
SP
A
Sound is output from speaker system A and
the same signal is output from the pre-out terminals.
SP
B
Sound is output from the two speakers
connected to speaker system B. Multichannel
sources will not be heard. The same signal is output
from the surround back channel pre-out terminals.
SP
AB
Sound is output from speaker system A (up
to 5 channels, depending on the source), the two
speakers in speaker system B, and the subwoofer.
The sound from speaker system B will be the same as
the sound from speaker system A (multichannel
sources will be downmixed to 2 channels).
SP
(off) No sound is output from the speakers. The
same sound is output from the pre-out terminals
(including from your subwoofer, if connected) as
when selecting speaker system A (above).
Note
The subwoofer output depends on the settings you
made in
Manual speaker setup
on page 43. However,
if
SP
B
is selected above, no sound is heard from the
subwoofer (the LFE channel is not downmixed).
Depending on the settings in
Surround back speaker
setting
on page 38 output from the surround back
pre-out terminals may change.
All speaker systems (except
Second Zone
connections) are switched off when headphones are
connected.
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
VSX_2014TX.book.fm 55
Other connections 10
56
En
Bi-amping your front speakers
Bi-amping is when you connect the high frequency driver
and low frequency driver of your speakers to different
amplifiers (in this case, to both front and surround back
terminals) for better crossover performance. Your
speakers must be bi-ampable to do this (having separate
terminals for high and low) and the sound improvement
will depend on the kind of speakers youre using.
1 Connect your speakers as shown below.
This illustration below shows the connections for bi-
amping your front left speaker. Hook up your front right
speaker in the same way.
Since both front and surround back speaker terminals
output the same audio, it doesnt matter which set (front
or surround back) is powering which part (
Hi
or
Low
) of
the speaker.
Make sure that the
+
/
connections are properly
inserted.
2 Select the Front Bi-Amp setting from the Surr
Back System menu.
See
Surround back speaker setting
on page 38 to specify
how youre using the surround back speaker terminals.
Caution
Most speakers with both
Hi
and
Low
terminals have
two metal plates that connect the
Hi
to the
Low
terminals. These must be removed when you are bi-
amping the speakers or you could severely damage
the amplifier. See your speaker manual for more
information.
If your speakers have a removable crossover network,
make sure you do not remove it for bi-amping. Doing
so may damage your speakers.
Bi-wiring your speakers
The reasons for bi-wiring are basically the same as bi-
amping, but additionally, interference effects within the
wire could be reduced, producing better sound. Again, to
do this your speakers must be bi-wireable (that is they
must have separate terminals for the high and low
frequencies). When bi-wiring, make sure youve selected
Normal (SB)
or
Second Zone
in
Surround back speaker
setting
on page 38.
To bi-wire a speaker, connect two speaker cords
to the speaker terminal on the receiver.
Caution
Make sure you use a parallel (not series, which are
fairly uncommon) connection when bi-wiring your
speakers.
Don't connect different speakers from the same
terminal in this way.
SPEAKERS
A B R L R L
R L(Single)
FRONT CENTER SURROUND SURROUND BACK /
SELECTABLE
SELECTABLE
Hi
Lo
Front left
speaker
VSX_2014TX.book.fm 56
Other connections 10
57
En
Connecting additional amplifiers
This receiver has more than enough power for any home
use, but its possible to add additional amplifiers to every
channel of your system using the pre-outs. Make the
connections shown below to add amplifiers to power
your speakers.
Important
Before making or changing the connections, switch
off the power and disconnect the power cord from the
AC outlet.
You can use the additional amplifier on the surround
back channel pre-outs for a single speaker as well. In
this case plug the amplifier into the left (
L (Single)
)
terminal only.
The sound from the surround back terminals will
depend on how you have configured the
Surround
back speaker setting
on page 38.
To hear sound only from the pre-outs, switch the
speaker system to
OFF
, or simply disconnect any
speakers that are connected directly to the receiver.
If youre not using a subwoofer, change the front
speaker setting (see
Speaker Setting
on page 44) to
large.
Multi-room listening
VSX-2014i-G model only
When used together with an optional IR receiver, this
receiver can power two independent systems in separate
rooms. Different sources can be playing in both rooms at
the same time or, depending on your needs, the same
source can also be used. The main and sub rooms have
independent power (the main room power can be off
while the sub room is on) and the sub room can be
controlled by this unit's remote control. You may need to
specify your volume setting and IR receiver type in
Multi
Room Setup
on page 67.
Making multi-room connections
It is possible to make these connections if you have a
separate amplifier, TV, speakers, and an IR receiver for
your sub room.
1 Connect the IR receiver sensor to the MULTI-
ROOM & SOURCE IR IN jack on the rear of this
receiver.
2 Connect a separate amplifier to the MULTI-
ROOM & SOURCE OUT jacks and a TV monitor to the
MULTI-ROOM & SOURCE MONITOR OUT jacks, both
on the rear of this receiver.
You should have a pair of speakers attached to the sub
room amplifier as shown in the illustration below.
Note
Even if you dont have an IR receiver, you can make
multi-room connections and use the front panel to
control the sub room.
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO AUDIO
VIDEO S-VIDEO
IN
OUT
OUT
OUT
ANTENNA
AM LOOP
FMUNBAL 75
R L
R L
R L
R
R
L
L
R L
L
OUT IN
ASSIGNABLE
OUT
DIGITAL /SAT)
1
1 4
Powered
subwoofer
Center channel
amplifier (mono)
INPUT
L R
ANALOG
INPUT
L R
ANALOG
INPUT
L R
ANALOG
INPUT
ANALOG
INPUT
ANALOG
Front channel
amplifier
Surround channel
amplifier
Surround back
channel amplifier
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR / VCR
DVD/ LD
TV/ SAT
OUT
PRE OUT
CEN- TER
CEN- TER
SUR- ROUND
SUR- ROUND
SUR- ROUND BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR / VCR
TV/ SAT
DVD/ LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI- ROOM & SOURCE
AUDIO VIDEO S-VIDEO
RS - 232C IN
IN
OUT
OUT
OUT
ANTENNA
AM LOOP FMUNBAL 75
MONITOR OUT
12V TRIGGER
Y
Y
PB
PR
PB
PR
Y
PB
PR
1 2
2
IN 1
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
OUT
REC
IN
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN
(DVD/ LD)
IN
(CD)
DIGITAL
IN (CD-R/ TAPE/MD) IN OUT DIGITAL (TV/SAT)
4
3
2 1
1 4
SPEAKERS
AC IN TWOVOLTAGE SELECTORS
230-240 V
120-127V 110V
A B R L R L R L(Single)
FRONT CENTER SURROUND SURROUND BACK /
SELECTABLE
SELECTABLE
220V
220V
230-240V
110V
120- 127V
Sub room
IR receiver
This receiver
Separate
amplifier
Main room
OUT
PRE
OUT
CEN-
TER
SUR-
ROUND
SUR-
ROUND
BACK
FRONT
SUBW.
CONTROL
MULTI-ROOM & SOURCE
MONITOR
MONITOR
VIDEO1
IN
IN
MULTI-
ROOM &
SOURCE
OUT
OUT
ANTENNA
12V
TRIGGER
Y
Y
PB
PR
PB
PR
IN 1
R L
R L
R L
L
OUT IN
OUT
I R
IN
(DC OUT12V/
100mA MAX)
VSX_2014TX.book.fm 57
Other connections 10
58
En
It is not possible to hear the digital output of a
component in the sub room. However, you can
connect the analog outputs of your digital
component into the receivers (analog) input
terminals to hear the component in the sub room.
Since the video converter is not enabled for multi-
room connections, youll have to connect any video
input source you want to watch in the sub room using
standard RCA video cords.
You can't use sound controls (such as the tone
controls or Midnight listening) or any surround
modes in the sub room. You can, however, use the
features available with your sub room amplifier.
Using the sub room controls
You can use the remote to adjust the sub room volume
and select sources from either the main room or the sub
room. You can also do this using the front panel controls.
Important
The receiver must be switched on (or in standby) in
the main room to control the sub room.
When someone is controlling the system from the
main room you won't be able to control the sub room
with the remote control.
If you are using a Pioneer amplifier in the sub room,
cover up the remote sensor to avoid changing the
settings when controlling the sub room.
Using the remote control in the sub room
When controlling the sub room, make sure to hold down
SHIFT
while pressing the remote control buttons below.
1 Point the remote control at the IR receiver and
press
RECEIVER.
This switches on the multi-room feature.
2 Press (SHIFT+) INPUT SELECT to select the input
source you want to listen to in the sub room.
3 Use (SHIFT+) VOLUME +/ to adjust the volume.
You wont be able to adjust the volume if it is set to
FIXED
in the
Multi Room Setup
on page 67.
You can only increase the volume to
0dB
.
In addition to the controls above, you can also use the
CLASS
,
STATION +/
and number buttons when
using the tuner.
Using the front panel multi-room controls
1 Press the MULTI ROOM ON/OFF button on the
front panel.
The
MULTI-ROOM
indicator lights in the front panel
display to indicate the multi-room control has been
switched on.
2 Press CONTROL.
Make sure that any operations for the sub room are done
while
MR:
(and the selected component) shows in the
display. If this is not showing, the front panel controls
affect the main room only.
3 Use the MULTI JOG dial to select the source.
Select between
DVD/LD
,
TV/SAT
,
DVR/VCR
,
TUNER
,
CD-R/TAPE/MD
or
CD
(in that order).
If you select
TUNER
, you can use the remote control
to select a preset station (see
Listening to station
presets
on page 48 if youre unsure how to do this).
4 Use the MASTER VOLUME dial to adjust the
volume.
This is only possible if you selected the
VARIABLE
volume control in
Multi Room Setup
on page 67.
You can only increase the volume to
0dB
.
5 When youre finished, press CONTROL again to
return to the main room controls.
You can also press the
MULTI ROOM ON/OFF
button on
the front panel to switch off all output to the sub room.
+10
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
DVD/LD TV/SAT DVR/VCR TVCONT
CD
TUNE
ST ST
CD-R/TAPE TUNER RECEIVER
ENTER
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
ENTER
TV CONTROL
RECEIVERCONTROL
SHIFT
VOL
TUNE
THX
SLEEP DIALOGE
AUTOSURR
STANDARD ADV.SURR STEREO
INPUT
SELECT
TV CH
DTVON/OFF
TUNER
DISPLAY
MPX
AUDIO
CHRETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CHSEL
ACOUSTIC
EQ
DTVINFO REC MUTE
TVVOL
RECSTOP
HDD
CH CH
DVD
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
RECEIVER
MASTER VOLUME
DVD/LD TV/SAT DVR/VCR VIDEO1
CD
CD-R/
TAPE/MD
STANDBY/ON
MULTI JOG
TUNER VIDEO2
LISTENING MODE
SELECT
ENTER
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF
MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
i.LINK
SELECT
MULTI
JOG
VSX_2014TX.book.fm 58
Other connections 10
59
En
Even if you dont press
CONTROL
above, the system
automatically switches back to the main room
controls.
Note
Multi-room cant be used when youre setting up the
system (from the on-screen
System Setup
menu).
You wont be able to switch the main room off
completely unless youve switched off the multi-room
control first.
When the multi-room feature is switched on, you can
also change the sub room input source with the front
panel
MULTI JOG
dial, even when the main unit is in
standby.
Remote operation may not be possible if direct light
from a strong fluorescent lamp is shining on the IR
receiver remote sensor window.
The tuner cannot be tuned to more than one station
at a time. Therefore, changing the station in one
room also changes the station in the other room.
Please be careful not to change stations when
recording a radio broadcast.
The volume levels of the main and sub rooms are
independent.
When the
MULTI ROOM OUT
jacks are connected to
a sub room amplifier with a remote sensor and
Pioneer
CONTROL
terminals (page 23), both the IR
receiver and the amplifier may receive remote control
commands (making correct operation impossible)
during multi-room operation. In this case, place the
IR receiver and amplifier apart from each other, and
point the remote control directly at the IR receiver
during operation.
If you dont plan to use the multi-room feature for
awhile, turn off the power in both the sub and main
rooms. Make sure the
MULTI-ROOM
indicator goes
off.
The sleep timer affects the sub room when the multi-
room feature is on.
Using the i.LINK interface
VSX-2014i-G model only
If you have a component with an i.LINK connector, you
can connect it to this receiver using an i.LINK cable.
Since the i.LINK interface does not transmit video
signals, the video signal of i.LINK-connected compo-
nents must be connected with other cables (see
Connecting video components
on page 18 for more on
making video connections).
If youve already made video connections
from the compo-
nent, assign the i.LINK input to the function (
DVD/LD
, for
example) corresponding to the video inputs to which
youve connected (see
Assigning the i.LINK inputs
on
page 64).
The two i.LINK connectors on the rear of your receiver are
4-pin connectors. Use a 4-pin, S400 i.LINK cable to
connect i.LINK-equipped components.
Caution
If your i.LINK connector comes into contact with
metallic parts of the receiver other than the i.LINK
terminal, an electrical short may occur. Some cables
have metal parts that may touch the unit when
connected. Please take care to use a suitable i.LINK
cable only.
Important
Please use 4-pin, S400 cables less than 3.5 meters
long. Although longer ones are available, they may
not work reliably.
There may be cases where the PQLS/rate control
function and/or the i.LINK audio does not work prop-
erly even when connected to i.LINK-compatible
equipment.
Do not connect/disconnect i.LINK cables or switch
on/off any components connected using i.LINK when
the receiver is on.
Copy-protected 96kHz DVD-Video discs can be heard
through the i.LINK connection, but they will be down-
sampled to 48kHz.
VSX_2014TX.book.fm 59
Other connections 10
60
En
1 Use an i.LINK cable to connect one of the i.LINK
connectors on this receiver to an i.LINK connector on
your i.LINK component.
The arrow on the cable connector body should be
lined up with the arrow to the right of the connector
on the receiver for correct alignment. The i.LINK
cable should be inserted straight into the connector
so that it snaps easily into place. If not connected
properly the receiver will not be able to recognize any
connected components. Note that the i.LINK cable is
fragile and can be broken easily if too much force is
used when connecting.
2 Assign the i.LINK component to the input you
want, then make any necessary output settings on
the component.
See
Assigning the i.LINK inputs
on page 64 to assign the
component to an input on this receiver. Follow the
operating instructions that came with the component to
make any necessary output settings.
Unassigned i.LINK components can be selected with
the front panel
i.LINK SELECT
button or the
INPUT
SELECT
button on the remote control.
Note
You can connect several components together using
i.LINK. See
Creating an i.LINK network
below.
About i.LINK
VSX-2014i-G model only
i.LINK is a trademark name for IEEE1394, a high-speed
interface for digital audio, video and other data found on
personal computers, digital camcorders, and other kinds
of audio and audio/visual equipment. A single i.LINK
connector can both send and receive data at the same
time, so only one cable is required to connect compo-
nents for two-way communication.
i.LINK and the i.LINK logo are trademarks of Sony
Corporation.
About PQLS rate control
Pioneer's PQLS (Precision Quartz Lock System)
technology provides high-precision digital audio from
DVD-A, SACD and audio CD sources when you use the
i.LINK interface. A precision quartz controller in this
receiver eliminates distortion caused by timing errors
(jitter), giving you the best possible digital-to-analog
conversion from the digital source.
To take advantage of PQLS, you must have a player
compatible with rate-control, and it must be switched on
and connected to this receiver through the i.LINK
network.
Creating an i.LINK network
Using i.LINK it is possible to chain up to 17 components
together so that the digital audio and control signals
from each component is available to other components
in the network. With the addition of an i.LINK repeater,
its possible to connect up to 34 components.
i.LINK connectors come in 4-pin and 6-pin configura-
tions. This player uses the 4-pin connection, but the two
types can be mixed on a network.
This receiver is compatible with i.LINK Audio (A&M
protocol) components, such as DVD players. Note that
when connected to i.LINK MPEG-II TS equipment (such
as a digital satellite tuner), i.LINK DV equipment (such as
a DVD recorder or DV camcorder), or an i.LINK-equipped
personal computer, audio and video signals are not
transmitted, and connecting to these devices sometimes
causes network interruptions. Check the operating
instructions supplied with your other i.LINK components
for compatibility information.
This receiver is DTCP (Digital Transmission Content
Protection) compliant, so you can play DVD-A, DVD-
Video, and SACD i.LINK audio.
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/
SAT
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI-
ROOM &
SOURCE
AUDIO
VIDEO S-VIDEO
RS - 232C
IN
IN
OUT
OUT
OUT
ANTENNA
AM LOOP
FMUNBAL 75
MONITOR OUT
12V
TRIGGER
Y
Y
PB
PR
PB
PR
Y
PB
PR
1 2
2
IN 1
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
OUT
REC
IN
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN
(DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN OUT
DIGITAL (TV/SAT)
4
3
2 1
1 4
S400
i.LINK-equipped component
VSX_2014TX.book.fm 60
Other connections 10
61
En
When setting up an i.LINK network, its important that
the components form an open ended chain (fig. 1), or a
tree (fig. 2).
The system will not work if the connected components
form a loop. If a loop is detected, the message
LOOP
CONNECT
shows in the display. Figs. 3 and 4 show
connections that form a loop.
Another consideration when connecting i.LINK devices
is the speed of the interface. At present there are three
speeds; S100 (slowest), S200 and S400 (fastest). This
receiver uses the S400 type. Although you can use
components with different speeds together, we
recommend connecting slower-speed components at
the edge of the network if possible (shown by the shaded
boxes in figs. 1 and 2). This will keep the network free of
bottlenecks.
When used within an i.LINK network, this receiver must
be on for the i.LINK connection to be maintained. Other
components in the network may or may not maintain the
connection in standby (none will when the power is
completely off)check the operating instructions
supplied with individual components. Note that the audio
may be momentarily interrupted if a component in the
i.LINK network is switched on/off, or its i.LINK
connection is switched on/off.
This product complies with the following i.LINK interface
specifications:
1) IEEE Std. 1394a-2000, Standard for a High Performance
Serial Bus
2) Audio and Music Data Transmission Protocol 2.0
Following the standard for AM824 sequence adaptation
layers, the product is compatible with IEC60958 bitstream,
DVD-A and SACD.
Switching components on and off
using the 12 volt trigger
VSX-2014i-G model only
You can connect components in your system (such as a
screen or projector) to this receiver so that they switch on
or off using a 12 volt trigger when you select an input
function. However, you must specify which input
functions switch on the trigger using the System Setup
menu (see
12 Volt Trigger Setup
on page 68 to do this).
Note that this will only work with components that have a
standby mode.
Connect the 12V TRIGGER jack of this receiver to
the 12V TRIGGER of another component.
Use a cable with a mono mini-plug on each end for the
connection.
The trigger maximum power is DC OUT 12V/100mA.
After youve specified the input functions that will switch
on the trigger, youll be able to switch the component on
or off just by pressing the input function(s) youve set on
page 68.
Using this receiver with a Pioneer
plasma display
If you have a Pioneer plasma display, you can use an
SR+ cable (see note below) to connect it to this unit and
take advantage of various convenient features, such as
automatic video input switching of the plasma display
when the input is changed.
Note that the illustration above shows the VSX-2014i-G
however, connection for the VSX-1014-S is the same.
fig. 1
fig. 2
i.LINK cable
i.LINK cable
fig. 3
fig. 4
i.LINK cable
i.LINK cable
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/
SAT
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR-
ROUND
BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM &SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
TV/
SAT
DVD/
LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI-
ROOM &
SOURCE
AUDIO
VIDEO S-VIDEO
RS - 232C
IN
IN
OUT
OUT
OUT
ANTENNA
AM LOOP
FMUNBAL 75
MONITOR OUT
12V
TRIGGER
Y
Y
PB
PR
PB
PR
Y
PB
PR
1 2
2
IN 1
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
OUT
REC
IN
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN
(DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN OUT
DIGITAL (TV/SAT)
4
3
2 1
1 4
OUT
CONTROL
Pioneer plasma
display
VSX_2014TX.book.fm 61
Other connections 10
62
En
Important
If you connect to a Pioneer plasma display using an
SR+ cable, you will need to point the remote control
at the plasma display remote sensor to control the
receiver. In this case, you wont be able to control the
receiver using the remote control if you switch the
plasma display off.
Use a 3-ringed miniplug SR+ cable to connect the
CONTROL IN jack of this receiver with the CONTROL
OUT jack of your plasma display.
Before you can use the extra SR+ features, you need to
make a few settings in the receiver. See
SR+ Setup for
Pioneer plasma displays
on page 67 for detailed
instructions.
To make the most of the SR+ features, you should
connect your source components (DVD player, etc.) in a
slightly different way to that described in this chapter. For
each component, connect the video output directly to the
plasma display, and just connect the audio (analog and/
or digital) to this receiver.
Note
This receiver is compatible with all Pioneer plasma
displays from 2003 onward.
The 3-ringed SR+ cable from Pioneer is commer-
cially available under the part number ADE7095.
Contact the Pioneer Customer Support division for
more information on obtaining an SR+ cable (you
can also use a commercially available 3-ringed mini
phone plug for the connection).
Using the SR+ mode with a Pioneer
plasma display
When connected using an SR+ cable, a number of
features become available to make using this receiver
with your Pioneer plasma display even easier. These
features include:
On-screen displays when making receiver settings,
such as speaker setup, MCACC setup, and so on.
On-screen volume display.
On-screen display of listening mode.
Automatic video input switching on the plasma
display.
Automatic volume muting on the plasma display.
See also
SR+ Setup for Pioneer plasma displays
on
page 67 for more on setting up the receiver.
1 Make sure that the plasma display and this
receiver are switched on and that they are
connected with the SR+ cable.
See
Using this receiver with a Pioneer plasma display
above for more on connecting these components.
2 To switch SR+ mode on/off, press RECEIVER, then
the SR+ button.
The front panel display shows
SR+ ON
or
SR+ OFF
.
Note
The automatic volume muting feature is enabled
separately; see
SR+ Setup for Pioneer plasma displays
on page 67.
DVD player
This receiver
Pioneer plasma
display
Satellite receiver, etc
VIDEO
INPUT 1
VIDEO
INPUT 2
TV/SAT
AUDIO IN
DVD
AUDIO IN
MASTER VOLUME
DVD/LD TV/SAT DVR/VCR VIDEO1
CD CD-R/ TAPE/MD TUNER VIDEO2
+10
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
DVD/LD TV/SAT DVR/VCR TVCONT
CD
TUNE
ST ST
CD-R/TAPE TUNER RECEIVER
ENTER
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
VSX_2014TX.book.fm 62
Other Settings 11
63
En
Chapter 11:
Other Settings
The Input Assign menu
You only need to make settings in the Input Assign menu
if you didnt hook up your digital equipment according to
the default settings for the digital inputs, or if you have
connected equipment using component video cables or
VSX-2014i-G only) an i.LINK connection.
1 Switch on the receiver and your TV.
Use the
RECEIVER
button to switch on.
2 Press RECEIVER on the remote control, then press
the SYSTEM SETUP button.
An on-screen display (OSD) appears on your TV. Use the
///
buttons and
ENTER
on the remote control to
navigate through the screens and select menu items.
Press
RETURN
to confirm and exit the current menu.
3 Select Input Assign from the System Setup
menu.
The illustration above shows the VSX-2014i-G OSD.
Assigning the digital inputs
Default settings:
Digital-1
(optical)
TV/SAT
Digital-2
(optical)
CD-R
Digital-3
(coaxial)
DVD/LD
Digital-4
(coaxial)
CD
You only need to do this if you didnt hook up your digital
equipment according to the default settings for the
digital inputs (see above). This setting tells the receiver
what digital equipment is hooked up to which terminal so
the buttons on the remote correspond to what you have
hooked up.
1 Select Digital Input from the Input Assign menu.
The illustration above shows the VSX-2014i-G OSD.
2 Select the number of the digital input to which
youve connected your digital component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
3 Select the component that corresponds with the
one you connected to that input.
Select between
DVD/LD
,
TV/SAT
,
DVR
,
VIDEO1
,
CD-R
,
CD
or
OFF
.
Use the
/
(cursor left/right)
buttons and
ENTER
to do this.
If you assign a digital input to a certain function (for
example,
DVD/LD
) then any digital inputs previously
assigned to that function will automatically be
switched off.
4 When you're finished, press RETURN.
You will return to the Input Assign menu.
+10
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
ENTER
TV CONTROL
VOL
DVD/LD TV/SAT DVR/VCR TVCONT
CD
ST ST
INPUT
SELECT
TV CH
DTVON/OFF
TUNER
DISPLAY
MPX
AUDIO
CHRETURN
SUBTITLE
DTVINFO REC MUTE
TVVOL
CD-R/TAPE TUNER RECEIVER
ENTER
RECSTOP
HDD DVD
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
TUNE
TUNE
System Setup
[ 1. Surr Back System ]
[ 2. AUTO MCACC ]
[ 3. MANUAL MCACC ]
[ 4. Manual SP Setup ]
[ 5. Input Assign ]
[ 6. Other Setup ]
Enter : Select
Return : Exit
5. Input Assign
[ a . Digital Input ]
[ b . Component Input ]
[ c . i. LINK Input ]
5. Input Assign
[ a . Digital Input ]
[ b . Component Input ]
[ c . i. LINK Input ]
5a. Digital Input
Digital - 1 [ TV/SAT ]
Digital - 2 [ CD-R ]
Digital - 3 [ DVD/LD ]
Digital - 4 [ CD ]
VSX_2014TX.book.fm 63
Other Settings 11
64
En
Assigning the component video inputs
Default settings:
Component 1
OFF
Component 2
OFF
If you used component video cords to connect your video
equipment you must tell the receiver which device it is, or
else you may see the S-video or composite video input
instead of the component video signal.
1 Select Component Input from the Input Assign
menu.
The illustration above shows the VSX-2014i-G OSD.
2 Select the number of the component video input
to which youve connected your video component.
Select between
DVD/LD
,
TV/SAT
,
DVR
,
VIDEO1
or
OFF
.
The numbers correspond with the numbers beside
the inputs on the back of the receiver.
3 Select the component that corresponds with the
one you connected to that input.
Use the
/
(cursor left/right)
buttons and
ENTER
to do this.
Make sure you have connected the audio from the
component to the corresponding inputs on the rear
of the receiver.
If you connect any source component to the receiver
using a component video input, you should also have
your TV connected to this receiver's component video
MONITOR
output.
4 When you're finished, press RETURN.
You will return to the Input Assign menu.
Assigning the i.LINK inputs
VSX-2014i-G model only
If you assign i.LINK-equipped components to an input
(for example
DVD/LD
), you will be able to select both
audio and video signals from i.LINK-equipped
components using the corresponding
MULTI CONTROL
button.
1 Select i.LINK Input from the Input Assign menu.
2 Select an i.LINK-equipped component.
When a number of i.LINK-equipped components are
connected to your receiver, the i.LINK-equipped
component you are looking for might be listed on
additional display screens.
If no i.LINK-equipped components are connected,
you wont be able to assign any inputs.
i.LINK
is displayed after unassigned device names
(e.g.
DV-868AVi [i.LINK]
).
If a connected devices cannot output (playback) a
source using the i.LINK connection,
[- - - -]
is
displayed after the input device name (e.g.
DV-
868AVi [- - - -]
). Non-compatible devices cannot be
assigned to inputs.
When the cables for an assigned input device
become loose or the power is cut to the device, an
asterisk (
) appears before the device name (e.g.
DV-868AVi [DVD/LD]
).
3 Select the component that you want to assign.
Use the
/
(cursor up/down)
buttons and
ENTER
.
When you assign an i.LINK-equipped video component,
select the input source to which you have connected the
video signal from the component.
If you assign an i.LINK input to a certain function (for
example
DVD/LD
) then any digital inputs previously
assigned to that function will automatically be set to
i.LINK
(not assigned).
The
TUNER
input cannot be assigned.
4 When you're finished, press RETURN.
You will return to the Input Assign menu.
5. Input Assign
[ a . Digital Input ]
[ b . Component Input ]
[ c . i. LINK Input ]
5b. Component Input
Component-1 [ DVD/LD ]
Component-2 [ OFF ]
5. Input Assign
[ a . Digital Input ]
[ b . Component Input ]
[ c . i. LINK Input ]
5c. i.LINK Input (1/1)
( End )
1 DV - 868AVi [ DVD/LD ]
2 DV - S858Ai [ i.LINK ]
( Top)
VSX_2014TX.book.fm 64
Other Settings 11
65
En
The Other Setup menu
The Other Setup menu is where you can make
customized settings to reflect how you are using the
receiver.
1 Switch on the receiver and your TV.
Use the
RECEIVER
button to switch on.
2 Press RECEIVER on the remote control, then press
the SYSTEM SETUP button.
An on-screen display (OSD) appears on your TV. Use the
///
buttons and
ENTER
on the remote control to
navigate through the screens and select menu items.
Press
RETURN
to confirm and exit the current menu.
3 Select Other Setup then press ENTER.
4 Select the setting you want to adjust.
If you are doing this for the first time, you may want to
adjust these settings in order:
The illustration above shows the VSX-2014i-G OSD.
DRC Setup
Specify the amount of dynamic range
adjustment to Dolby Digital soundtracks (see
Dynamic Range Control Setup
below).
Dual Mono Setup
Isolate one channel when
listening to discs with dual mono encoding (see
Dual
Mono Setup
below).
LFE ATT Setup
Choose the attenuator level for the
LFE channel (
LFE Attenuator Setup
below).
SR+ Setup
Specify how you want to control your
Pioneer plasma display (
SR+ Setup for Pioneer
plasma displays
on page 67).
The following are available with the VSX-2014i-G model:
Multi Room Setup
Specify your volume setting
and IR receiver type for a multi-room setup (see
Multi
Room Setup
on page 67).
12V Trigger Setup
Specify which components are
switched on or off using the 12 volt trigger (see
12 Volt
Trigger Setup
on page 68).
SACD GAIN Setup
Listen to high sound quality and
greater detail with SACDs (see
SACD Gain Setup
on
page 68).
5 Make the adjustments necessary for each
setting, pressing RETURN to confirm after each
screen.
+10
INPUT ATT FLDIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
ENTER
TV CONTROL
VOL
DVD/LD TV/SAT DVR/VCR TVCONT
CD
ST ST
INPUT
SELECT
TV CH
DTVON/OFF
TUNER
DISPLAY
MPX
AUDIO
CHRETURN
SUBTITLE
DTVINFO REC MUTE
TVVOL
CD-R/TAPE TUNER RECEIVER
ENTER
RECSTOP
HDD DVD
D.ACCESS
TOP MENU
DTVMENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
TUNE
TUNE
System Setup
[ 1. Surr Back System ]
[ 2. AUTO MCACC ]
[ 3. MANUAL MCACC ]
[ 4. Manual SP Setup ]
[ 5. Input Assign ]
[ 6. Other Setup ]
Enter : Select
Return : Exit
6. Other Setup
[ a . DRC Setup ]
[ b . Dual Mono Setup ]
[ c . LFE ATT Setup ]
[ d . SR+ Setup ]
[ e . Multi Room Setup ]
[ f . 12V Trigger Setup ]
[ g . SACD GAIN Setup ]
VSX_2014TX.book.fm 65
Other Settings 11
66
En
Dynamic Range Control Setup
Default setting:
OFF
This setting specifies the amount of dynamic range
adjustment to Dolby Digital and DTS movie soundtracks.
You may want to use this when listening to surround
sound at low volumes.
1 Select DRC Setup from the Other Setup menu.
2 Choose the setting that you want.
OFF
No dynamic range adjustment (use when
listening at higher volume).
MID
Mid setting.
MAX
Dynamic range is reduced (loud sounds are
reduced in volume while quieter sounds are
increased).
3 When you're finished, press RETURN.
You will return to the Other Setup menu.
Dual Mono Setup
Default setting:
CH1
You can specify how dual mono encoded Dolby Digital
soundtracks should be played. Dual mono is not widely
used, but is sometimes necessary when two languages
need to be sent to separate channels.
1 Select Dual Mono Setup from the Other Setup
menu.
2 Choose the setting that you want.
CH1
Only channel 1 is played
CH2
Only channel 2 is played
CH1 CH2
Both channels are played through the
front speakers
3 When you're finished, press RETURN.
You will return to the Other Setup menu.
Note
This setting works only with dual mono encoded
Dolby Digital and DTS soundtracks.
Tip
While the receiver is in standby (using the front
panel), press the
STANDBY/ON
button while
holding down the
TUNER EDIT
button to change the
dual mono setting.
LFE Attenuator Setup
Default setting:
ATT 0 dB
Some Dolby Digital and DTS audio sources include ultra-
low bass tones. Set the LFE attenuator as necessary to
prevent the ultra-low bass tones from distorting the
sound from the speakers.
1 Select LFE ATT Setup from the Other Setup
menu.
2 Choose the setting that you want.
ATT 0dB
No limiting (recommended setting)
6. Other Setup
[ a . DRC Setup ]
[ b . Dual Mono Setup ]
[ c . LFE ATT Setup ]
[ d . SR+ Setup ]
[ e . Multi Room Setup ]
[ f . 12V Trigger Setup ]
[ g . SACD GAIN Setup ]
6a. DRC Setup
DRC [ OFF ]
6. Other Setup
[ a . DRC Setup ]
[ b . Dual Mono Setup ]
[ c . LFE ATT Setup ]
[ d . SR+ Setup ]
[ e . Multi Room Setup ]
[ f . 12V Trigger Setup ]
[ g . SACD GAIN Setup ]
6b. Dual Mono Setup
Dual Mono
[ CH1 ]
6. Other Setup
[ a. DRC Setup ]
[ b. Dual Mono Setup ]
[ c. LFE ATT Setup ]
[ d. SR+ Setup ]
[ e . Multi Room Setup ]
[ f . 12V Trigger Setup ]
[ g . SACD GAIN Setup ]
6c. LFE ATT Setup
LFE ATT [ ATT 0dB ]
VSX_2014TX.book.fm 66
Other Settings 11
67
En
ATT 10dB
10dB of limiting
LFE OFF
No sound from LFE channel
3 When you're finished, press RETURN.
You will return to the Other Setup menu.
SR+ Setup for Pioneer plasma displays
Make the following settings if you have connected a
Pioneer plasma display to this receiver using an SR+
cable. Note that the number of function settings available
will depend on the plasma display youve connected.
See also
Using this receiver with a Pioneer plasma display
on page 61 and
Using the SR+ mode with a Pioneer
plasma display
on page 62.
1 Select SR+ Setup from the Other Setup menu.
2 Select the PDP Volume Control setting you
want.
OFF
The receiver does not control the volume of the
plasma display
ON
When the receiver is switched to one of the
inputs that use the plasma display (
DVD/LD
, or
another one of functions below), the volume on the
plasma display is muted so only sound from the
receiver is heard.
3 Assign any input source connected to the plasma
display to the corresponding input number.
This matches the receivers input source with a
numbered video input on the plasma display. For
example, assign
DVD/LD
to
input-2
if you have
connected the your DVD video output to video input 2 on
the plasma display.
The
Monitor Out Connect
should be set to the input
that youve used to connect this receiver to your
plasma display.
4 When you're finished, press RETURN.
You will return to the Other Setup menu.
Multi Room Setup
VSX-2014i-G model only
Default setting:
VARIABLE
/
Setting 1
If youve made multi-room connections (see
Multi-room
listening
on page 57) you may need to specify your
volume setting and IR receiver type.
1 Select Multi Room Setup from the Other Setup
menu.
2 Select the volume level setting.
VARIABLE
Use this setting if youve connected a
power amplifier in the sub room (this receiver is
simply being used as a pre-amp) and you will be
using this receivers controls to adjust the volume.
FIXED
Use this setting if youve connected a fully
integrated amplifier (such as another Pioneer VSX
receiver) in the sub room and want to use that
receivers volume controls.
Caution
With the
FIXED
setting, the source is sent from this
receiver at maximum volume, so make sure the
volume is quite low in the sub room at first and then
experiment to find the correct level.
6. Other Setup
[ a . DRC Setup ]
[ b . Dual Mono Setup ]
[ c . LFE ATT Setup ]
[ d . SR+ Setup ]
[ e . Multi Room Setup ]
[ f . 12V Trigger Setup ]
[ g . SACD GAIN Setup ]
6d. SR+ Setup
PDP Volume Control
[ OFF ]
PDP Input Select
DVD/LD [ input-3 ]
TV/SAT [ TV ]
DVR [ input-1 ]
VIDEO1 [ OFF ]
VIDEO2 [ OFF ]
Monitor Out Connect
[ input-2 ]
6d. SR+ Setup
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD [ input-3 ]
TV/SAT [ TV ]
DVR [ input-1 ]
VIDEO1 [ OFF ]
VIDEO2 [ OFF ]
Monitor Out Connect
[ input-2 ]
6d. SR+ Setup
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD [ input-2 ]
TV/SAT [ TV ]
DVR [ input-1 ]
VIDEO1 [ OFF ]
VIDEO2 [ OFF ]
Monitor Out Connect
[ input-2 ]
6. Other Setup
[ a . DRC Setup ]
[ b . Dual Mono Setup ]
[ c . LFE ATT Setup ]
[ d . SR+ Setup ]
[ e . Multi Room Setup ]
[ f . 12V Trigger Setup ]
[ g . SACD GAIN Setup ]
6e. Multi Room Setup
Volume Level
[ VARIABLE ]
IR Setting
[Setting 1]
CAUTION:If the "FIXED"
position is chosen, the
volume will be loud.
6f. Multi Room Setup
Volume Level
[ FIXED ]
IR Setting
[Setting 1]
CAUTION:If the "FIXED"
position is chosen, the
volume will be loud.
VSX_2014TX.book.fm 67
Other Settings 11
68
En
3 Select the type of IR receiver youre using.
Setting 1
Use this setting for most IR receivers.
Setting 2
Use this setting if the IR receiver youre
using doesnt seem to work after selecting
Setting 1
.
4 When you're finished, press RETURN.
You will return to the Other Setup menu.
Note
Some IR receivers may not work with this receiver.
Check with your audio dealer for more information.
12 Volt Trigger Setup
VSX-2014i-G model only
Default setting:
OFF
(all components)
After connecting a component the 12 volt trigger (see
Switching components on and off using the 12 volt trigger
on page 61), it switches on automatically when you select
an input function set to switch the trigger on. Specify
which input functions switch on the trigger below.
1 Select 12V Trigger Setup from the Other Setup
menu.
2 Select an input function and choose the setting
that you want.
This should be the input function, that when selected,
switches on the 12 volt trigger.
OFF
12 volt trigger is not activated for the selected
component.
ON
12 volt trigger is activated for the selected
component.
3 Repeat for as many input functions as you would
like to set.
4 When you're finished, press RETURN.
You will return to the Other Setup menu.
SACD Gain Setup
VSX-2014i-G model only
Default setting:
0dB
You can get more detail from SACDs by maximizing the
dynamic range (during digital processing) using the
SACD gain feature.
1 Select SACD GAIN Setup from the Other Setup
menu.
2 Switch the SACD gain between 0dB and 6dB.
For most SACD sources, selecting
6dB
will result in high
sound quality and greater detail. The level will be
adjusted automatically for playback at the same volume.
3 When you're finished, press RETURN.
You will return to the Other Setup menu.
Note
You shouldnt have any problems using this feature
with most SACD discs, but if the sound distorts, it is
best to switch the gain setting back to
0dB
.
6e. Multi Room Setup
Volume Level
[ VARIABLE ]
IR Setting
[ Setting 1 ]
6. Other Setup
[ a . DRC Setup ]
[ b . Dual Mono Setup ]
[ c . LFE ATT Setup ]
[ d . SR+ Setup ]
[ e . Multi Room Setup ]
[ f . 12V Trigger Setup ]
[ g . SACD GAIN Setup ]
6f. 12V Trigger Setup
DVD/LD [ OFF ]
TV/SAT [ OFF ]
DVR [ OFF ]
VIDEO1 [ OFF ]
VIDEO2 [ OFF ]
TUNER [ OFF ]
CD-R [ OFF ]
CD [ OFF ]
6f. 12V Trigger Setup
DVD/LD [ ON ]
TV/SAT [ OFF ]
DVR [ OFF ]
VIDEO1 [ OFF ]
VIDEO2 [ OFF ]
TUNER [ OFF ]
CD-R [ OFF ]
CD [ OFF ]
6. Other Setup
[ a . DRC Setup ]
[ b . Dual Mono Setup ]
[ c . LFE ATT Setup ]
[ d . SR+ Setup ]
[ e . Multi Room Setup ]
[ f . 12V Trigger Setup ]
[ g . SACD GAIN Setup ]
6g. SACD GAIN Setup
SACD GAIN [ + 6dB ]
VSX_2014TX.book.fm 68
Additional information 12
69
En
Chapter 12:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest Pioneer authorized independent service company to carry out repair work.
Power
Symptom Cause Remedy
The power does not turn on. The power plug is disconnected. Connect the power plug to the wall outlet.
The protection circuit may have been
activated.
Disconnect the power plug from the outlet, and insert
again.
The receiver suddenly switches
off.
The speaker wires are frayed or sticking out
of the jack, and are touching the back of the
receiver or another set of wires.
Reinsert the speaker wires, making sure there are no
stray strands of wire and that they are inserted fully.
The receiver has a serious problem. Unplug the receiver from the wall and call a Pioneer
authorized independent service company.
During loud playback the power
suddenly switches off.
The protection circuit has been activated
because the lowest actual impedance of the
speakers (as opposed to the speakers rated
impedance) is dangerously low.
Turn down the volume.
When its convenient, go to
Acoustic Calibration EQ
on
page 41 and lower the 40 Hz and 125 Hz equalizer levels
using the manual setting.
Turning the digital safety feature on may allow you to
turn up the volume a little more. To switch between
SAFETY ON
and
SAFETY OFF
, put the receiver into
standby, then press the
STANDBY/ON
button while
holding down the
SYSTEM SETUP
button on the front
panel.
The unit does not respond when
the buttons are pressed.
Static electricity caused by dry air. Switch the unit off, then on again.
Disconnect the power plug from the outlet, and insert
again.
AMP ERR
blinks in the display,
then the power automatically
switches off. The
MCACC
blinks
and the power does not turn on.
The receiver has a serious problem. Do not try to turn on the receiver. Contact a Pioneer
authorized independent service company for assistance.
FAN STOP
blinks in the display,
then the power automatically
switches off.
Something is obstructing the fan. Remove the obstruction and try switching the receiver
back on. If the fan is still not working, or you cant remove
the object, unplug the receiver from the wall and call a
Pioneer authorized independent service company.
The fan is malfunctioning. Unplug the receiver from the wall and call a Pioneer
authorized independent service company.
OVERHEAT
blinks in the display
then the power automatically
switches off.
The internal temperature of the unit has
become too high.
After allowing the unit to cool down in a well-ventilated
place, try switching the receiver back on. Make sure you
follow the guidelines for improving heat dispersal in
Ventilation
on page 2.
VSX_2014TX.book.fm 69
Additional information 12
70
En
No sound
Symptom Cause Remedy
No sound is output when an
input source is selected.
No sound output from the front
speakers.
Improper connections. Make sure you have properly connected the component
to the corresponding input on the back of the receiver
(see
Connecting up
on page 14).
Sound is muted or the volume is turned
down.
Press
MUTE
or adjust the volume accordingly.
Speakers are turned off or selected
improperly with the
SPEAKERS
switch.
Press
SPEAKERS
to select the proper speaker set (see
Switching the speaker system
on page 55).
The input signal type is incorrect. Press
SIGNAL SELECT
to select the proper input signal
(see
Choosing the input signal
on page 33).
The multichannel analog inputs are
selected.
Press
MULTI CH IN
again (see
Selecting the
multichannel analog inputs
on page 37).
The front speakers arent connected
properly.
See
Connecting the speakers
on page 21 to connect
them properly.
No sound from the surround or
center speakers.
Speaker settings are incorrect. (for
example, they have been set to
NO
).
Check you speaker settings in
Speaker Setting
on
page 44.
The surround and/or center levels are
turned down.
Check the levels in
Channel Level
on page 45.
The surround and/or center speakers are
disconnected.
Check
Connecting the speakers
on page 21 to make sure
the speakers are connected correctly.
The
STEREO
listening mode has been
selected.
Choose a surround listening mode (see
Listening in
surround sound
on page 30).
No sound from surround back
speakers.
Surround back speakers are set to
NO
. Set the surround back speakers to
LARGE
or
SMALL
(see
Speaker Setting
on page 44).
The Extended mode is switched to
AUTO
or
OFF
.
Set to
Extended ON
(see
Using the surround back
channel (Extended mode)
on page 34).
The source is not a 6.1 channel playback
source.
Switch the Extended mode to
Extended ON
(see
Using
the surround back channel (Extended mode)
on page 34)
and choose a surround listening mode (see
Listening in
surround sound
on page 30).
The surround back speakers are
disconnected.
Check
Connecting the speakers
on page 21 to make sure
the speakers are connected correctly.
The surround back channel is on the 1
speaker setting, and your speaker is
connected to the right channel output.
Connect the speaker to the surround back left channel
output (
Connecting the speakers
on page 21).
The Extended mode is switched to
AUTO
and the Dolby Surround EX / DTS ES software
youre playing has no ag to indicate it is 6.1
compatible.
You can still listen with surround back sound by setting
to
Extended ON
(
Using the surround back channel
(Extended mode)
on page 34).
No sound from subwoofer. The subwoofer is disconnected or switched
off.
Connect or switch on the subwoofer (see
Connecting
the speakers
on page 21).
Make sure the sleep function on your subwoofer isnt
activated.
The subwoofer's settings are incorrect. Set the subwoofer (see
Speaker Setting
on page 44) to
YES
or
PLUS
.
The crossover frequency is set too low. Set the crossover frequency to a (higher) frequency that
matches your speaker characteristics (see
Crossover
Network
on page 45)
There is very little low frequency information
in your source.
Change your subwoofer setting to one of the following in
the
Speaker Setting
on page 44:
Front:
SMALL
/ Subwoofer:
YES
Front:
LARGE
/ Subwoofer:
PLUS
The LFE channel is switched off. See
LFE Attenuator Setup
on page 66 to adjust the
setting.
The subwoofer's levels are too low. See
Channel Level
on page 45 to check the speaker
levels.
Check the volume control on the subwoofer to make
sure it is turned up.
VSX_2014TX.book.fm 70
Additional information 12
71
En
Other audio problems
No sound from one speaker. The speaker setting has been set to
NO
. Change the setting in
Speaker Setting
on page 44.
The speaker level is too low. Check the level in
Channel Level
on page 45.
The speaker isnt connected properly. Check
Connecting the speakers
on page 21 to make sure
the speaker is connected correctly.
The source has no sound output for that
channel.
By choosing an advanced effect listening mode (see
Listening in surround sound
on page 30), you may be able
to create an extra channel for the speaker.
Sound is produced from analog
components, but not from digital
ones (DVD, LD, CD-ROM etc.).
The digital input assignment is wrong. Assign the digital inputs correctly (see
Assigning the
digital inputs
on page 63).
The digital components aren't connected
properly.
Make sure you have properly connected the digital
component to the corresponding input on the back of the
receiver (see
Connecting up
on page 14).
The player is not compatible with the source
you're using, or the player settings are
incorrect.
Choose a compatible source, or check the components
manual for the correct settings.
The digital output level has been turned
down on a CD recorder or other component
equipped with digital output level adjustment
capability.
Set the digital volume level of the player to full, or to the
neutral position.
The multichannel analog inputs are
selected.
Press
MULTI CH IN
again (see
Selecting the
multichannel analog inputs
on page 37).
The input signal type is set to
ANALOG
. Set the input signal type to
DIGITAL
(see
Choosing the
input signal
on page 33).
No sound is output or a noise is
output when Dolby Digital/DTS
software is played back.
A DVD player not compatible with Dolby
Digital/DTS is being used.
Make sure your DVD player is compatible with Dolby
Digital/DTS.
The settings on the DVD player are incorrect
and/or the DTS signal output is turned off.
Make sure the player's settings are correct and/or the
DTS signal out is on. Refer to the instruction manual
supplied with the DVD player.
The digital output level is turned down on a
CD player or other component equipped with
digital output level adjustment capability. (The
DTS signal has been altered by the player, and
cannot be read.)
Set the digital volume level of the player to full, or to the
neutral position.
Symptom Cause Remedy
Symptom Cause Remedy
Broadcast stations cannot be
selected automatically, or there
seems to be considerable noise
in radio broadcasts.
FM broadcasts
The FM antenna is not fully extended or is
poorly positioned.
Fully extend the FM wire antenna, position for best
reception, and secure to a wall.
Weak radio signals. Connect an outdoor FM antenna (see page 19).
AM broadcasts
The AM antenna is poorly positioned. Adjust the direction and position for best reception.
Weak radio signals. Connect an additional internal or external AM antenna
(see page 19).
Interference caused by other equipment
(uorescent lamp, motor, etc.).
Turn off the equipment causing the noise or move it
away from the receiver.
Place the antenna farther away from the equipment
causing the noise.
A multi channel DVD source
appears to be downmixed from 2
channels during playback.
The source is coming from something other
than the
MULTI CH IN
jacks (for example,
digital PCM output, etc.)
Check the
MULTI CH IN
connections (see
Connecting
multichannel analog components
on page 17) and select
the multichannel analog inputs with the
MULTI CH IN
button (see
Selecting the multichannel analog inputs
on
page 37).
Noise is output when scanning a
DTS CD.
The scan function performed by the player
slightly alters the digital information, making
it unreadable.
This is not a malfunction, but be sure to turn the volume
down to prevent the output of loud noise from your
speakers.
When playing a DTS format LD
there is audible noise on the
soundtrack.
The input signal type is set to
ANALOG
. Set the input signal type to
DIGITAL
(see
Choosing the
input signal
on page 33)
VSX_2014TX.book.fm 71
Additional information 12
72
En
Video
Can't record audio. You are trying to make an analog recording
from a digital signal, or a digital recording of
an analog source.
You can only record analog to analog, or digital to
digital.
The digital source is copy protected. You can't record digital sources that have been copy
protected.
The analog
REC
jacks have not been
connected properly.
Check your analog connections (see
Connecting analog
audio components
on page 17).
Subwoofer output is very low. The speaker settings result in very little
audio signal being sent to the subwoofer.
To route more audio signal to the subwoofer, set it to
PLUS
, or select
SMALL
for the front speaker setting (see
Speaker Setting
on page 44).
The signal is not downmixed
when listening to a multichannel
DVD-Audio disc (for example,
you only hear the front left and
right channels when listening in
stereo).
The disc is downmix prohibited. This is not a malfunction.
Everything seems to be set up
correctly, but the playback sound
is odd.
The speakers are out of phase. Check that the positive/negative speaker terminals on
the receiver are matched with the corresponding
terminals on the speakers (see
Connecting the speakers
on page 21).
Noise or hum can be heard even
when there is no sound being
input.
There is electrical interference from another
component or appliance.
Check that personal computers or other digital
components connected to the same power source are not
causing interference.
There seems to be a time lag
between the speakers and the
output of the subwoofer.
The subwoofer channel can be delayed
slightly if run through a low-pass lter.
See
Automatically setting up for surround sound
(MCACC)
on page 11 to set up your system again using
MCACC (this will automatically compensate for a delay in
the subwoofer output).
The maximum volume available
(shown in the front panel display)
is lower than the
+12dB
maximum.
The channel levels may have been adjusted. This is not a malfunction. If the levels in
Channel Level
on page 45 have been adjusted, the maximum volume will
change accordingly.
Symptom Cause Remedy
Symptom Cause Remedy
No image is output when an
input is selected.
The video connections are incorrect. Make sure the video component is connected correctly
(see page 18).
You are using component video
connections for your source, but not for your
TV.
Using the video converter, video signals can be
converted from a composite or S-video input to a
component video output, but not vice-versa (VSX-2014i-G
only). See
About the video converter
on page 15 for more
on this.
You are using component video
connections and the component video inputs
are assigned incorrectly.
Check
Assigning the component video inputs
on page 64
to make sure youre assigned the correct input.
The DVD/video player settings are incorrect. Set correctly. Refer to the instruction manual supplied
with the DVD/video player.
The video input selected on the TV monitor
is incorrect.
Set correctly. Refer to the instruction manual supplied
with the TV.
Even though the sub room monitor is
connected properly, the multi-room feature is
switched off.
Press the
MULTI ROOM&SOURCE ON/OFF
button to
switch it on.
The component video inputs are assigned
to a video component connected only to the
composite or S-Video terminals.
Check
Assigning the component video inputs
on page 64
to make sure the component video assign for that video
component is switched to
OFF
.
You connected your TV to the
MULTI ROOM
& SOURCE MONITOR OUT
jack instead of
the main
MONITOR OUT
jack.
Connect the
MONITOR OUT
jack to the TV monitor (see
Connecting video components
on page 18).
VSX_2014TX.book.fm 72
Additional information 12
73
En
Settings
Display
The
System Setup
screen
doesn't appear (or is displayed
incorrectly).
Some TVs connected to the receiver with
component video cables do not display the
System Setup
screen when the Color Burst
feature is on.
When the receiver is in standby, switch to
COLOR
BURST OFF
by holding down the front panel
ACOUSTIC
EQ
button and pressing
STANDBY/ON
. (the current
setting appears in the display).
The
MONITOR OUT
jack hasn't been
connected.
You connected your TV to the
MULTI ROOM
& SOURCE MONITOR OUT
jack instead of
the main
MONITOR OUT
jack.
Connect the
MONITOR OUT
jack to the TV monitor (see
Connecting video components
on page 18).
VSX-1014-S model only
The TV format
setting for your country or region is incorrect.
See
Changing the TV format setting
on page 76 to
change the format setting to match your country or
region.
Cant record video. You are trying to record a source connected
to the component video jacks.
Connect the source component to either the composite
video or the S-video jacks (see
Connecting video
components
on page 18).
The source is copy protected. You can't record sources that have been copy protected.
The recorder's video input is hooked up
using a different type of cable to the source
video output.
Hook up the source and the recorder using the same
type of video cable (
VSX-2014i-G model only
see
About the
video converter
on page 15 for exceptions to this).
Symptom Cause Remedy
Symptom Cause Remedy
The Auto MCACC Setup
continually shows an error.
The ambient noise level in the room is too
high, or obstacles are blocking the setup
microphone.
Keep the noise level in the room as low as possible
when using the Auto MCACC Setup (see
Other problems
when using the Auto MCACC Setup
on page 13 for more
on this). If the noise cannot be kept low enough, you will
have to set up the surround sound manually (page 43).
After using the Auto MCACC
Setup, the speaker size setting
(
LARGE
or
SMALL
) is incorrect.
There was some inaudible low-frequency
noise in the room.
The low-frequency noise could have been caused by an
air conditioner or motor. Switch off all appliances in the
room and rerun the Auto MCACC Setup.
The display shows
KEY LOCK
ON
when you try to make
settings.
Your Pioneer dealer has enabled the key
lock feature.
Ask your Pioneer dealer to disable the key lock.
12V TRG ERR
blinks in the
display.
There is a problem with the 12V trigger
connection.
Turn the receiver off and check the 12V trigger
connection.
Symptom Cause Remedy
The display is dark or off. The display is set to dark or off. Press
FL. DIMMER
on the remote control repeatedly to
select a different brightness.
After making an adjustment the
display goes off.
The display is set to off. Press
FL. DIMMER
on the remote control repeatedly to
select a different brightness.
You can't get
DIGITAL
to display
when using the
SIGNAL SELECT
button.
There is a problem with the digital
connections or the digital input is assigned
incorrectly.
Check your digital connections and/or assign the digital
inputs correctly (see
Assigning the digital inputs
on
page 63).
The multichannel analog inputs are
selected.
Press
MULTI CH IN
again (see
Selecting the
multichannel analog inputs
on page 37).
The Dolby/DTS indicator doesn't
light when playing Dolby/DTS
software.
The player is paused. Press play.
The player's sound output settings are
wrong.
Set the player correctly (consult the manual that came
with the player, if necessary).
When playing a DVD-Audio disc,
the DVD player display shows
96
kHz
. However, the receivers
display does not.
The audio from these discs is output from
the analog audio jacks of the DVD player only;
the receiver does not show the sampling rate
of the input signal through the analog inputs.
This is not a malfunction. See also the operating
instructions that came with your DVD player.
During playback of a DTS 96/24
source, the display doesn't show
96kHz
.
The receivers input signal type is set to
analog.
Set the receiver to
AUTO
or
DIGITAL
(see
Choosing the
input signal
on page 33).
VSX_2014TX.book.fm 73
Additional information 12
74
En
Remote control
When playing Dolby Digital or
DTS sources, the receivers
format indicators do not light.
No digital connection, or the digital
connection is incorrect.
Check the digital audio connection (page 16).
The receivers input signal type is set to
analog.
Set the receiver to
AUTO
or
DIGITAL
(see
Choosing the
input signal
on page 33).
The DVD player is set to output Dolby Digital
and/or DTS audio as PCM.
Check the settings on the player. Set the output for
Dolby Digital and DTS (no PCM conversion). See also the
operating instructions that came with your DVD player.
The disc has several playback audio tracks;
the one currently playing is actually PCM.
Switch the playback audio channel on your DVD player.
See the operating instructions that came with your DVD
player.
When playing certain discs,
none of the receivers format
indicators light.
The audio format of the disc is not 5.1/6.1
channel.
This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
When playing a disc, the
2
PL II
or
Neo:6
indicator lights
on the receiver.
The input signal type is set to analog. Set the receiver to
AUTO
or
DIGITAL
(see
Choosing the
input signal
on page 33).
A two channel soundtrack is currently
playing.
This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
The soundtrack currently playing is
encoded using Dolby Surround.
This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
During playback of a Surround
EX or DTS ES source on the
Extended AUTO
setting, the
EX
and
ES
indicators dont light, or
the signal is not properly
processed.
The source may be Dolby Surround EX /
DTS ES software, but it has no ag to indicate
it is 6.1 compatible.
Set to
Extended ON
(see
Using the surround back
channel (Extended mode)
on page 34) then switch to the
THX Surround EX or Standard EX listening mode (see
Listening in surround sound
on page 30).
Symptom Cause Remedy
Symptom Cause Remedy
Cannot be remote controlled. The remote control batteries have worn out. Replace the batteries (see
Loading the batteries
on
page 7).
Too far away or improper angle of operation. Operate within 7 meters and a 30 angle of the remote
sensor on the front panel (see
Operating range of remote
control unit
on page 7).
There is an obstacle between the receiver
and the remote control.
Remove the obstacle or move to another place.
Strong light such as uorescent light is
shining onto the unit's remote control sensor.
Avoid exposing the remote sensor on the front panel to
direct light.
Something is plugged into the
CONTROL IN
jack.
Unplug the cable from the
CONTROL IN
jack and use
remote normally (see
Operating other Pioneer components
on page 23).
VSX-2014i-G model only
The IR receiver
type is mismatched with the setting.
Disconnect the IR receiver from the rear panel or set to
the other IR receiver type (see
Multi Room Setup
on
page 67).
Other components can't be
operated with the system
remote.
The preset code settings are wrong. Input the correct preset code.
The batteries wore out and the system
settings were cleared.
Reset the proper system settings.
The SR cable is connected, but
the connected components cant
be operated with the remote.
The SR cable hasn't been connected
properly.
Reinsert the SR cable, making sure its connected to the
right jack (see
Operating other Pioneer components
on
page 23).
The rest of the component connections
have not been made.
Make sure an analog connection has been made
between the units.
The component you have hooked up is not a
Pioneer product.
This feature only works with Pioneer products.
VSX_2014TX.book.fm 74
Additional information 12
75
En
i.LINK interface
VSX-2014i-G model only
i.LINK messages
VSX-2014i-G model only
You may see the following messages displayed in the front panel display when using the i.LINK interface:
Symptom Cause Remedy
No sound is output. An output signal is not produced from the
i.LINK connector on the source player.
Refer to the manual that came with the source player.
The selected component is not compatible
with i.LINK audio.
Refer to the manual that came with the source player.
The input signal is set to
DIGITAL
or
ANALOG
.
Select
i.LINK
or
AUTO
using the
SIGNAL SELECT
button (see
Assigning the i.LINK inputs
on page 64).
i.LINK indicator does not light up
even when an i.LINK-equipped
component is selected.
The
DIGITAL
or
ANALOG
input signal is
selected.
Select
i.LINK
or
AUTO
using the
SIGNAL SELECT
button (see
Assigning the i.LINK inputs
on page 64).
The i.LINK cable has become disconnected. Check all connections.
The i.LINK cable is too long. Use a cable less than 3.5m long.
The selected component does not
correspond to the i.LINK Audio format.
Refer to the manual for the selected component.
The component between the unit and the
source player is turned off.
When the source player is turned off or in standby, the
output signal is not produced. Refer to the manual for the
selected component.
PQLS OFF
or
PQLS ON
is
displayed temporarily on your
player and the sound output is
discontinued.
During playback through an i.LINK
connection, if you change the settings for
other i.LINK components, the sound will be
discontinued momentarily.
This is not a malfunction.
The program format indicators
dont disappear when SACD
playback stops.
The program format indicators remain lit
until another format source is input.
This is not a malfunction.
You cant get i.LINK to display
when using the
SIGNAL SELECT
button.
i.LINK-equipped component(s) are not
ready.
Turn on the component(s).
i.LINK input setting is incorrect. Select the correct i.LINK input setting (see
Assigning
the i.LINK inputs
on page 64).
After upgrading a component, it
is not recognized and cannot be
selected using the i.LINK
connection.
Depending on the upgrade process, certain
components may cease to be recognized by
the receiver.
You may need to reset the i.LINK database memory in
the receiver (use the front panel):
With the receiver in standby, press
STANDBY/ON
while holding down
RETURN
. When you see
DB CLEAR?
appear in the display, press
ENTER
, then
SET UP
to
conrm. When youve reset the i.LINK database memory,
DB CLEAR SET
shows in the display. If
DB ERROR
is
displayed, step through the procedure again.
Message Explanation
BUS FULL
The i.LINK bus has reached its capacity and cannot transmit any more data.
CANNOT LINK 1
The connection between the receiver and the selected i.LINK-equipped component is unstable. If the
i.LINK cables appear to be connected properly and both the receiver and i.LINK-equipped component are
on, switch both units off, then on again to re-establish the connection between them.
CANNOT LINK 2
The receiver cant identify the selected i.LINK-equipped component. For example, the receiver may not be
able to identify an i.LINK-equipped personal computer.
LINK CHECK
The receiver is checking the i.LINK network. It does this when components are added to, or removed from
the network. The sound may be interrupted if this happens during playback.
LOOP CONNECT
The i.LINK network cannot function because the connected components form a loop. See
Creating an
i.LINK network
on page 60 for more on this.
NO NAME
When an i.LINK-equipped component has no name, this message is displayed instead of the proper
component name.
NO SIGNAL
A component is outputting an i.LINK signal that the receiver cannot reproduce. This receiver can only
reproduce signals from i.LINK-Audio equipped components. See
About i.LINK
on page 60 for more on
this.
VSX_2014TX.book.fm 75
Additional information 12
76
En
Note
If the unit does not operate normally due to external effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal operating conditions.
Resetting the main unit
Use this procedure to reset all the receivers settings to
the factory default. Use the front panel controls to do this.
1 Switch the receiver into standby.
2 While holding down the TONE button, press and
hold the
STANDBY/ON button for about three
seconds.
3 When you see RESET? appear in the display,
press ENTER.
OK?
shows in the display.
4 Press SYSTEM SETUP to confirm.
OK
appears in the display to indicate that the receiver
has been reset to the factory default settings.
Changing the frequency step
If you find that you cant tune into stations successfully,
the frequency step may not be suitable for your country/
region. Heres how to switch the setting:
1 Switch the receiver into standby.
2 While holding down the front panel BAND
button, press
STANDBY/ON.
The display shows the new setting:
9K STEP
For areas with an FM reception of 50kHz
and AM reception of 9kHz
10K STEP
For areas with an FM reception of 100kHz
and AM reception of 10kHz
Note
If youre unsure of the correct frequency step for your
region, consult your local Pioneer dealer.
Switching the speaker impedance
We recommend using speakers of 8
with this system,
but it is possible to switch the impedance setting if you
plan to use speakers with a 6
impedance rating.
With the receiver in standby, press
STANDBY/
ON while holding down the SPEAKERS button.
Each time you do this, you switch between the
impedance settings:
SP 6 OHM
Use this setting if your speakers are
rated at 6
SP 8 OHM
Use this setting if your speakers are
rated at 8
or more.
Changing the TV format setting
VSX-1014-S model only
If the
System Setup
menu is not displayed correctly, it
may be that the TV system is set incorrectly for your
country or region.
With the receiver in standby, press
STANDBY/
ON while holding down the SIGNAL SELECT button.
The display shows the new setting (
PAL
or
NTSC
).
PQLS OFF
This is displayed on a playback component when PQLS turns off during playback. The sound may be
interrupted momentarily when this happens.
PQLS ON
This is displayed on a playback component when PQLS turns on during playback. The sound may be
interrupted momentarily when this happens.
UNKNOWN
When an i.LINK-equipped component name cannot be recognized, this message is displayed instead of
the proper component name.
Message Explanation
12_additional_info.fm 76
Additional information 12
77
En
Surround sound formats
Below is a brief description of the main surround sound
formats youll find on DVDs, satellite, cable and
terrestrial broadcasts, and video cassettes.
Dolby
The Dolby technologies are explained below. See
www.dolby.com for more detailed information.
Dolby Digital
Dolby Digital is a multichannel digital audio coding
system widely used in cinemas, and in the home for DVD
and digital broadcast soundtracks. It can deliver up to six
discrete audio channels, comprising five full range
channels and a special LFE (low frequency effects)
channel used mainly for deep, rumbling sound effects;
hence the term 5.1-channel Dolby Digital.
In addition to the format features above, Dolby Digital
decoders offer downmixing for compatibility with mono,
stereo and Dolby Pro Logic audio from a number of bit
rates and channels. Another feature, called Dialog
Normalization, attenuates programs based on the
average level of dialog in a program relative to its peak
level (also known as Dialnorm) in order to achieve
uniform playback level.
Dolby Digital Surround EX
Dolby Digital Surround EX (the EX stands for EXtended)
is an extension of Dolby Digital encoding whereby a
surround back channel is matrixed into the surround left/
right channels for 6.1 channel playback. This allows for
compatibility with Dolby Digital 5.1 channel decoding, as
well as for decoding using Dolby Digital EX.
Dolby Pro Logic IIx and Dolby Surround
Dolby Pro Logic IIx is an improved version of the Dolby
Pro Logic II (and Dolby Pro Logic)
decoding
system. Using
the innovative steering logic circuit, this system
extracts surround sound from sources as follows:
Dolby Pro Logic
4.1 channel sound (mono
surround) from any stereo source
Dolby Pro Logic II
5.1 channel sound (stereo
surround) from any stereo source
Dolby Pro Logic IIx
6.1 or 7.1 channel sound
(stereo surround and surround back) from two
channel or 5.1(and 6.1) channel sources
With two channel sources, the .1 subwoofer channel is
generated by bass management in the receiver.
Dolby Surround is an
encoding
system which embeds
surround sound information within a stereo soundtrack,
which a Dolby Pro Logic decoder can then use for
enhanced surround listening with greater sound detail.
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, Surround EX and the double-D
symbol are trademarks of Dolby Laboratories.
DTS
The DTS technologies are explained below. See
www.dtstech.com for more detailed information.
DTS Digital Surround
DTS Digital Surround is a 5.1-channel audio coding
system from Digital Theater Systems Inc. now widely
used for DVD-Video, DVD-Audio, 5.1 music discs, digital
broadcasts, and video games. It can deliver up to six
discrete audio channels, comprising five full range
channels, including an LFE channel. Higher sound
quality is achieved through the use of a low compression
rate, and high rates of transmittance during playback.
DTS-ES
DTS-ES (the ES stands for Extended Surround) is a
decoder that is capable of decoding both DTS-ES
Discrete 6.1 and DTS-ES Matrix 6.1 encoded sources.
DTS-ES Discrete 6.1 gives true 6.1 channel sound, with
a completely separate (discrete) surround back channel.
DTS-ES Matrix 6.1 has a surround back channel matrixed
into the surround left/right channels. Both sources are
also compatible with a conventional DTS 5.1 channel
decoder.
DTS Neo:6
DTS Neo:6 can generate 6.1 channel surround sound
from any matrixed stereo source (such as video or TV)
and from 5.1 channel sources. It uses both the channel
information already encoded into the source, as well as
its own processing to determine channel localization
(with two channel sources, the .1 subwoofer channel is
generated by bass management in the receiver). Two
modes (Cinema and Music) are available using DTS
Neo:6 with two channel sources.
DTS 96/24
DTS 96/24 is an extension of the original DTS Digital
Surround which offers high quality 96 kHz / 24-bit audio
using a DTS 96/24 decoder. This format is also fully
backward compatible with all existing decoders. This
means that DVD players can play this software using a
conventional DTS 5.1 channel decoder.
DTS, DTS-ES, Neo:6 and DTS 96/24 are trademarks
of Digital Theater Systems, Inc.
VSX_2014TX.book.fm 77
Additional information 12
78
En
About THX
The THX technologies are explained below. See
www.thx.com for more detailed information.
THX Cinema processing
THX is an exclusive set of standards and technologies
established by the world-renowned film production
company, Lucasfilm Ltd. THX grew from George Lucas'
personal desire to make your experience of the film
soundtrack, in both movie theatres and in your home
theatre, as faithful as possible to what the director
intended. Movie soundtracks are mixed in special movie
theatres called dubbing stages and are designed to be
played back in movie theatres with similar equipment
and conditions. This same soundtrack is then transferred
directly onto Laserdisc, VHS tape, DVD, etc., and is not
changed for playback in a small home theatre
environment. THX engineers developed patented
technologies to accurately translate the sound from the
movie theatre environment into the home, correcting the
tonal and spatial errors that occur. On this product, when
the THX indicator is on, THX features are automatically
added in Cinema modes (e.g. THX Cinema, THX
Surround EX).
Re-Equalization
The tonal balance of a film soundtrack will be excessively
bright and harsh when played back over audio
equipment in the home because film soundtracks were
designed to be played back in large movie theaters using
very different professional equipment. Re-Equalization
restores the correct tonal balance for watching a movie
soundtrack in a small home environment.
Timbre Matching
The human ear changes our perception of a sound
depending on the direction from which the sound is
coming. In a movie theatre, there is an array of surround
speakers so that the surround information is all around
you. In a home theatre, you use only two speakers located
to the side of your head. The Timbre Matching feature
filters the information going to the surround speakers so
that they more closely match the tonal characteristics of
the sound coming from the front speakers. This ensures
seamless panning between the front and surround
speakers.
Adaptive Decorrelation
In a movie theatre, a large number of surround speakers
help create an enveloping surround sound experience,
but in a home theatre there are usually only two speakers.
This can make the surround speakers sound like
headphones that lack spaciousness and envelopment.
The surround sounds will also collapse into the closest
speaker as you move away from the middle seating
position. Adaptive Decorrelation slightly changes one
surround channel's time and phase relationship with
respect to the other surround channel. This expands the
listening position and createswith only two speakers
the same spacious surround experience as in a movie
theatre.
THX Select
Before any home theatre component can be THX Select
certified, it must incorporate all the features above and
also pass a rigorous series of quality and performance
tests. Only then can a product feature the THX Select
logo, which is your guarantee that the Home Theatre
products you purchase will give you superb performance
for many years to come. THX Select requirements cover
every aspect of the product including pre-amplifier and
power amplifier performance and operation, and
hundreds of other parameters in both the digital and
analog domain.
THX Surround EX
THX Surround EX - Dolby Digital Surround EX is a joint
development of Dolby Laboratories and the THX Ltd. In a
movie theater, film soundtracks that have been encoded
with Dolby Digital Surround EX technology are able to
reproduce an extra channel which has been added
during the mixing of the program. This channel, called
Surround Back, places sounds behind the listener in
addition to the currently available front left, front center,
front right, surround right, surround left and subwoofer
channels. This additional channel provides the
opportunity for more detailed imaging behind the listener
and brings more depth, spacious ambience and sound
localization than ever before. Movies that were created
using the Dolby Digital Surround EX technology, when
released into the home consumer market may exhibit
wording to that effect on the packaging. A list of movies
created using this technology can be found on the Dolby
web site at www.dolby.com.
Only receiver and controller products bearing the THX
Surround EX logo, when in the THX Surround EX mode,
faithfully reproduce this new technology in the home.
This product may also engage the THX Surround EX
mode during the playback of 5.1 channel material that is
not Dolby Digital Surround EX encoded. In such case the
information delivered to the Surround Back channel will
be program dependent and may or may not be very
pleasing depending on the particular soundtrack and the
tastes of the individual listener.
THX is a trademark or registered trademark of THX Ltd.
Surround EX is a jointly developed technology of THX and
Dolby Laboratories and is a trademark of Dolby
Laboratories. Used under authorization. All rights reserved.
VSX_2014TX.book.fm 78
Additional information 12
79
En
Specifications
Amplifier section
Maximum Output Power . . . . . . . . . . . . . . . .170 W/channel
(1 kHz, THD 10.0%, 8
)
Continuous Power Output
Front . . . . . . . . . . . 130 W + 130 W (DIN 1kHz, THD 1%, 8
)
Center . . . . . . . . . . . . . . . . . 130 W (DIN 1kHz, THD 1%, 8
)
Surround . . . . . . . 130 W + 130 W (DIN 1kHz, THD 1%, 8
)
Surround back . . 130 W + 130 W (DIN 1kHz, THD 1%, 8
)
Rated Power Output . . . . . . . . . . . . . . . . . . . . . 100W+100W
(20Hz20kHz, 0.09%, 8
)
Audio Section
Input (Sensitivity/Impedance)
LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 mV/47 k
Frequency Response
LINE. . . . . . . . . . . . . . . . . . . . . .5 Hz to 100,000 Hz dB
Output (Level/Impedance)
REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 mV/2.2 k
Tone Control
BASS . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 dB (100 Hz)
TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . 6 dB (10 kHz)
LOUDNESS. . . . . . . . . . . . . . +4/+2 dB (100Hz/10 kHz)
(at volume position 40dB)
Signal-to-Noise Ratio (IHF, short circuited, A network)
LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 dB
Signal-to-Noise Ratio
[DIN (continuous rated power output/50mW]
LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92/65 dB
Composite Video / S-Video Section
Input (Sensitivity/Impedance) . . . . . . . . . . . . . . 1 Vp-p/75
Output (Level/Impedance) . . . . . . . . . . . . . . . . . 1 Vp-p/75
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . 65 dB
Frequency Response . . . . . . . . . . . . . 5 Hz to 10 MHz dB
Component Video Section
Input (Sensitivity/Impedance) . . . . . . . . . . . . . . 1 Vp-p/75
Output (Level/Impedance) . . . . . . . . . . . . . . . . . 1 Vp-p/75
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . 65 dB
Frequency Response . . . . . . . . . . . . . 5 Hz to 40 MHz dB
FM Tuner Section
Frequency Range . . . . . . . . . . . . . . . . 87.5 MHz to 108 MHz
Usable Sensitivity . . . . . . Mono: 15.2 dBf, IHF (1.6 V/75
)
50 dB Quieting Sensitivity . . . . . . . . . . . . . . Mono: 20.2 dBf
Stereo: 41.2 dBf
Sensitivity (DIN) . . . . . . . . . . . . . . Mono: 1.1 V (S/N 26dB)
Stereo: 50 V (S/N 46dB)
Signal-to-Noise Ratio . . . . . . . . . . . Mono: 76 dB (at 85 dBf)
Stereo: 72 dB (at 85 dBf)
Signal-to-Noise Ratio (DIN) . . . . . . . . . . . . . . . .Mono: 62 dB
Stereo: 58 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . Stereo: 0.6% (1 kHz)
Alternate Channel Selectivity . . . . . . . . . . . 70 dB (400 kHz)
Stereo Separation . . . . . . . . . . . . . . . . . . . . . . .40 dB (1 kHz)
Frequency Response . . . . . . . . . . . . 30 Hz to 15 kHz 1dB
Antenna Input . . . . . . . . . . . . . . . . . . . . . . 75
unbalanced
AM Tuner Section
Frequency Range . . . . . . 531 kHz to 1,602 kHz (9kHz step)
530 kHz to 1,700 kHz (10kHz step)
Sensitivity (IHF, Loop antenna) . . . . . . . . . . . . . . . 350 V/m
Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna
Miscellaneous
Power Requirements
. . . . . . . . . . . . . . . AC 110/120127/220/230240 V, 50/60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . .470 W
In standby . . . . . . . . . . . . . . . . . . . . . . 0.67 W (220V/50Hz)
Dimensions . . . . . . . . . . . . 420 (W) x 173 (H) x 465 (D) mm
Weight (without package)
VSX-2014i-G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.6 kg
VSX-1014-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.4 kg
Furnished Parts
Microphone (for Auto MCACC setup) . . . . . . . . . . . . . . 1
Microphone stand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA/LR6 dry cell batteries
. . . . . . . . . . . . . . . . . . . . . . . . . . 2
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Antenna adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Flad-bladed converter plug. . . . . . . . . . . . . . . . . . . . . . . . . . 1
Power cord(s):
VSX-1014-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
VSX-2014i-G (PAL model) . . . . . . . . . . . . . . . . . . . . . . . . . 1
VSX-2014i-G (NTSC model) . . . . . . . . . . . . . . . . . . . . . . . . 2
These operating instructions
Note
Specifications and the design are subject to possible
modifications without notice, due to improvements.
Cleaning the unit
Use a polishing cloth or dry cloth to wipe off dust and
dirt.
When the surface is dirty, wipe with a soft cloth
dipped in some neutral cleanser diluted five or six
times with water, and wrung out well, and then wipe
again with a dry cloth. Do not use furniture wax or
cleansers.
Never use thinners, benzine, insecticide sprays or
other chemicals on or near this unit, since these will
corrode the surface.
VSX_2014TX.book.fm 79
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270 K002_A_En
Published by Pioneer Corporation.
Copyright 2004 Pioneer Corporation.
All rights reserved.
<04H00001> Printed in <ARB7306-A>
VSX_2014TX.book.fm 80