GREENLEE Hyd Punch Driver
GREENLEE Hyd Punch Driver
GREENLEE Hyd Punch Driver
Read and understand all of the instructions and safety information in this manual before operating or servicing this tool.
999 9606.5
Safety
Safety is essential in the use and maintenance of Greenlee tools and equipment. This instruction manual and any markings on the tool provide information for avoiding hazards and unsafe practices related to the use of this tool. Observe all of the safety information provided.
Purpose
This manual is intended to familiarize personnel with the safe operation and maintenance procedures for the following Greenlee hydraulic punch driver kits: 38456 38520 7306/7306SB 7310/7310SB 7506 7606SB 7610SB 7625/7625Pg/7625PgSB 7646/7646Pg/7646PgSB and Slug-Buster, Slug-Splitter, are registered trademarks of Greenlee Textron. Keep this manual available to all personnel. Replacement manuals are available upon request at no charge.
Description
The Greenlee hydraulic punch driver sets combine the 746 Hydraulic Ram with the 767 Hand Pump or the 1725 Foot Pump. These hydraulic driver sets are intended to be used with either standard or Slug-Buster punches and dies to punch holes through plastic, fiberglass, aluminum and steel. Greenlee Slug-Splitter punches, dies, and draw studs are capable of punching through all of these materials and stainless steel. Round punches are available for punching holes from 12.7mm through 144mm (1/2" through 5-5/8") in diameter, including 1/2" through 5" conduit and pipe sizes. Other shapes are available square, special square, rectangular, D, double D, electronic connector, oiltight with notches, and key. The maximum thickness of material that the punch can penetrate depends on the size and shape of the punch. See the instruction manual supplied with the punch for individual punch capacities.
Electric shock hazard: Do not use this tool near live circuits. This includes, but is not limited to, the following: near circuit breaker panels or fuse boxes with energized circuits near junction boxes with energized circuits Failure to observe this warning can result in severe injury or death.
Immediate hazards which, if not avoided, WILL result in severe injury or death.
Skin injection hazard: Oil under pressure easily punctures skin causing serious injury, gangrene or death. If you are injured by escaping oil, seek medical attention immediately. Hand-tighten all couplers completely before operating the pump. Do not use tools to tighten the couplers. Do not use hands to check for leaks. Do not hold hose or couplers while the hydraulic system is pressurized. Release the hydraulic pressure before disconnecting the hoses or couplers, and before servicing the pump or accessory.
Hazards or unsafe practices which, if not avoided, MAY result in injury or property damage.
Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Failure to observe this warning will result in severe injury or death.
Wear eye protection when operating or servicing this tool. Failure to wear eye protection can result in serious eye injury from flying debris or hydraulic oil.
A component failure could throw broken parts. Do not allow anyone to stand in front of the punch or behind the hydraulic ram. Close access doors or covers on any equipment that is in line with the punch or ram. Failure to observe this warning can result in severe injury or death.
Replace worn, damaged or missing components with Greenlee replacement parts. Worn or damaged components can fail, resulting in injury or property damage. Inspect the pump, hoses, couplers, and fittings for wear or damage. Inspect all punch components (punch, die, draw stud, etc.) for wear or damage. Failure to observe these warnings can result in severe injury or death.
Do not attempt to punch a hole through two or more layers of material. This will bend or break the draw stud, and could throw parts with great force. Failure to observe this warning can result in severe injury or death.
Do not exceed the rated capacity of this tool. Exceeding the rated capacity could cause a component failure, which could throw broken parts with great force. Failure to observe this warning can result in severe injury or death.
Set up the tool properly. An improper setup could cause a component to fail and strike nearby personnel with great force. Thread the punch completely onto the draw stud. All of the punch threads must be engaged by the draw stud threads. Incomplete assembly could cause a component failure. Use only Greenlee punches, dies and draw studs. Other manufacturers components might not withstand the forces generated by this punch driver. Failure to observe these warnings can result in severe injury or death.
The punch driver will fall free when the punch is complete. Support the weight of the tool when punching. Do not allow anyone to stand beneath an overhead punch. Failure to observe this warning can result in injury or property damage.
Use this tool for the manufacturers intended purpose only. Any other use can result in injury or property damage.
This punch system was designed for a maximum operating pressure of 450 Bar (6500 psi). Use this punch system with the Greenlee 767 Hand Pump or 1725 Foot Pump only. Connect the pump to the ram with Greenlee hoses and couplers only. Use of any other hoses or couplers could result in injury from a component failure.
Note:
All of the punch threads must be engaged by the draw stud threads. If any of the punch threads are not engaged, disassemble the setup, remove one of the spacers and reassemble the setup.
Note:
If the ram stops before the hole is complete, stop pumping. Check that the setup is correct and that you have not exceeded the tools capacity. See the setup instructions. If necessary, disassemble the setup and add a spacer.
9. Activate the pump. For specific instructions, see the operating manual supplied with the pump. Note: Support the weight of the ram when operating the pump. This will prevent the ram from falling when the punch is complete. 10. Release the pressure at the pump.
PUNCH
DIE
3 SPACERS
Completed Assembly
MATERIAL
PUNCH
DIE
SPACER AS NEEDED
MATERIAL
PUNCH
DIE
E B N A
G K J I H
C D O L
P C N
C N
A E
D D O G Q H I J
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1 2 2 2 2 2 2
1 1 1
N O
1725
31353
37729
37729
52515
52515
Standard and Slug-Buster punches, dies and draw studs listed on the following page are capable of punching a maximum of 10 (.1344", 3 mm) gauge mild steel. Slug-Splitter punches, dies and draw studs listed on the following page are capable of punching a maximum of 10 (.1344", 3 mm) gauge stainless steel.
7646
7306SB 1 1 1
7306 1 1
7310SB 1 1 1
7310 1 1
7625
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
KEY 1 2 3 4 5 6 7 8 9 10 11 12
UPC NO. 78-3310500 3294.1 502 9452.2 501 7093.7 501 7095.3 501 1251.1 501 1253.8 905 4167.7 905 4168.5 905 0338.4 905 0389.9 905 0390.2 905 0832.7 905 1339.8 501 4552.5 501 2121.9
DESCRIPTION
QTY.
Shaft (746 M-3) ........................................................... 1* Shaft (746 SS) ............................................................ 1** Piston .......................................................................... 1 Cylinder ....................................................................... 1 Spring, Compression .................................................. 1 Retainer ...................................................................... 1 Coupler, 1/4" Quick Disconnect .................................. 1 Plug, Protective ........................................................... 1 O-Ring, 7/8" x 1-1/8" x 1/8" ......................................... 1 O-Ring, 2" x 2-3/8" x 3/16" .......................................... 1 Ring, Retainer ............................................................. 2 Ring, 2" x 2-3/8" x 3/16" Spiral Backup ...................... 1 Ring, 7/8" x 1-1/8" x 1/8" Spiral Backup ..................... 1 Packing Repair Kit (not shown) .................................. 1 Decal, Safety (not shown) .......................................... 1 Supplied with the 746 and used with standard punches and Slug-Buster punches Supplied with the 746 SS and used with Slug-Splitter punches and dies
* **
Maintenance
The pump and ram require little maintenance. Use the tool with care to keep dirt and grit out of the hydraulic system. All internal working parts are lubricated by the hydraulic oil, so that no other lubrication is necessary.
Repair
All repair work should be performed at an authorized Greenlee service center. Use only Greenlee replacement parts. Using any parts other than Greenlee replacement parts may do irreparable damage and will void the warranty.