AP238 PST1/PST2 Manual
AP238 PST1/PST2 Manual
AP238 PST1/PST2 Manual
N17478
IMPORTANT:
Read and save these instructions.
NOTICE:
Installer: Leave this guide with the homeowner
Homeowner: Keep this guide for future reference
To reduce the risk of injury to persons in the event of a stove top grease fire:
• SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn OFF the burner.
BECAREFUL TO PREVENT BURNS. NEVER PICK UP A FLAMING PAN—you may be burned.
KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames DO
NOT go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT or dial your local
emergency service immediately.
• DO NOT USE WATER, including wet dishcloths or towels — a violent steam explosion will result.
• Use an extinguisher ONLY if:
• You know you have a Class A, B, C extinguisher, and you already know how to operate it.
• The fire is small and contained in the area where it is started.
• The fire department is being called.
• You can fight the fire with your back to an exit.
WARNING
This is the safety alert symbol. This symbol alerts you to potential hazards that can hurt you and others.
All safety messages will follow the safety alert symbol and the word “WARNING”.
The manufacturer and/or distributor/reseller declines all responsibility in the event of failure to ob-
serve the instructions given here for installation, maintenance and suitable use of the product.
The manufacturer and/or distributor/reseller further declines all responsibility for injury due to neg-
ligence and the warranty of the unit automatically expires due to improper maintenance.
The manufacturer and/or distributor/reseller will not be held responsible for any damages to per-
sonal property or real estate or any bodily injuries whether caused directly or indirectly by the range
hood.
Page 2
Table of Contents
Tools needed:
Measuring
Marker or tape
pencil Utility knife
Level
Flat-blade
Powered
and Phillips
screwdriver
screwdrivers
or drill
Page 3
Parts supplied:
Single-piece Chimney
Under Cabinet Range Hood (vary with model) (Optional)
Qty: 8 PCS
(Flat head)
Optional for
Single-piece Qty: 8 PCS
Chiomney
Qty: 8 PCS
Grease Tunnel
Page 4
Venting Requirements Height & Clearance
To calculate the length of the system you need, deduct the equivalent feet for each vent piece used in the system
from the recommended maximum duct run.
Page 6
Venting Methods
• This range hood is factory set for venting through the roof or wall.
• Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.
IMPORTANT:
• NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or
garages. All exhaust must be ducted to the outside.
• Use metal/aluminum duct work only.
• Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape.
• Use caulking to seal exterior wall or roof opening around the cap.
Roof cap
Page 7
Electrical Requirements
If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that
the ground path is adequate.
A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp circuit, fused on both sides
of the line.
DO NOT ground to a gas pipe.
Check with a qualified electrician if you are not sure that the range hood is properly grounded.
DO NOT have a fuse in the neutral or ground circuit.
Wire sizes (copper wire only) and connections must conform with the rating of the appliance as specified on
the model/serial rating label. Wire sizes must conform to the requirements of the National Electrical Code
ANSI/NFPA 70 — latest edition*, or CSA Standards C22. 1-94, Canadian Electrical Code Part 1 and C22.
2 No. 0-M91 - latest edition** and all local codes and ordinances. A U.L. - or C.S.A. - listed conduit con-
nector must be provided at each end of the power supply cable (at the range hood and at the junction box).
Copies of the standards listed may be obtained from:
* National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
** CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
Page 8
Preparation
Advanced Preparations:
• Be familiar with the controls of the range hood by reading
through Range Hood Operations, Page 12.
• Place the range hood on a flat, stable surface. Connect the
WARNING
Excessive Weight
range hood to a designated standard outlet (please refer the Require three or more person to move and
product label for the suitable voltage of this unit) and turn on install this range hood. Spinal or other bodi-
the range hood. Verify all operations of the range hood by ly injuries could occur if it is not followed.
referring to Range Hood Operations, Page 12.
• Place all supplied parts and required hardware on a flat, stable surface and ver-
ify the existence of all supplied parts listed on Page 4.
• Carefully remove the white plastic protective coat from the range hood.
WARNING
Severe Injury
Rotating fan can cause severe
injury. Stay clear of fan when
Preparations: motor is running.
NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.
• Decide the location of the venting pipe from the hood to the outside. Refer to Venting Methods on Page 7.
• A straight, short vent run will allow the hood to perform more efficiently.
• Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the
hood.
• IMPORTANT: Peel white plastic protective coat off the hood, if any.
• Use silver tape or duct tape to seal joints between pipe sections.
• For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not provided) on
each side. Refer to Figure 1.
• Using references in Measurements and Diagrams on Page 21, create access opening for electrical wires and
hood exhaust under the cabinet.
CAUTION: If moving the cooking range is necessary to install the hood, turn OFF the power on an elec-
tric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE.
• Puncture the knockout holes (for mounting under the cabinet) on the hood as shown in Figure 2.
• If necessary, attach two rubber stands with 3M adhesive tapes to the back corners of the hood.
• Attach ducting transition to hood exhaust with included 10 round head screws as shown in Figure 3.
Page 9
Installation
1. You can mount this range hood to both under cabinet and wall:
i. Using references in Height & Clearance on Page 5 and Measurements and Diagrams on Page 20, center the hood
beneath the cabinet and flush with the front of the cabinet.
ii. Make sure the range hood is level and not tilted. Mark the locations of the hanging bracket holes on the
wall and/or cabinet. Refer to Figure 4.
iii. Place aside all equipments, locate marked regions and drill holes. Attach range hood to wall using anchors recom-
mended for your type of wall:
a. Sheet rock wall: Attach range hood to stud blockings if possible. If stud blockings are not available, it is
required to build a supporting structure behind the sheet rock for best weight support.
b. Concrete wall: Use designated screws (not provided).
c. Wood wall: Use at least 5 cm long wood screws (not provided).
iv. Install Ducting Transition on top of the range hood. Refer to Figure 5.
v. Draw electrical wires through cabinet access opening and center the hood beneath the cabinet.
vi. From inside of the hood, place screws into the exact center of each knockout hole and secure to cabinet bottom.
Finish tightening all screws until secure. Be careful when using electrical screwdriver, damage to the range hood
may occur.
CAUTION: Make certain the range hood is secure before releasing!
2. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more secure installa-
tion, use as many mounting holes as needed to secure from the inside of hood.
i. Use 8” round steel pipe (follow building codes in your area) to connect the exhaust on the hood to the ductwork
above. Use silver tape or duct tape to make all joints secure and air tight. Refer to Figure 7.
SAFETY WARNING: Risk of electrical shock. this range hood must be properly grounded. Make sure this is done
by qualified electrician in accordance with all applicable national and local electrical codes. Before connecting wires,
switch power off at service panel and lock service panel to prevent power from being switched on accidentally.
3. Connect the range hood to a designated standard outlet or cut off the plug and connect three wires (black, white and
green) to house wires and cap with wire connectors. Connect according to colors (i.e. black to black, white to white,
and green to green) as shown in Figure 8.
Page 10
Installation (Continued)
4. Store excess wires in the wiring box.
5. OPTIONAL: If you purchased a single-piece chimney cover, attach it to the hood in this step.
6. Drop oil tunnel into recess support near rear of hood. Refer to Figure 9.
7. To install baffle filters and stainless spacer(s), refer to Baffle Filters and Stainless Steel Spacers on Page 23 for baffle
filter and stainless spacer placement. Refer to Figure 10 for the following five steps:
Angle baffle filter toward back of hood.
Push baffle filter up until almost level.
Slide forward into recess behind the front of hood.
Lower baffle filter.
Slide back until it fits into resting positions.
8. Repeat Step 8 to install all baffle filters and stainless spacers.
9. OPTIONAL: Install heating lamps (not included) last. 220V or 120V (for USA & Canada), 250-Watt
maximum per lamp.
10. Turn powe ON in control panel. Check all lights and fan operations.
11. Make sure to leave this Installation Guide for the homeowner.
Figure 10
Figure 7
Figure 8
Figure 9 Page 11
Range Hood Operations & Wiring Diagram
Power Light
Decrease Value Increase Value
Blower Power Indicator Power-On Elapsed Digital Timer
Blower Speed Indicator Power-Off Delay Digital Timer
Light Power Indicator Power-Off Delay Timer Indicator
The island canopy hood is designed to remove smoke, cooking vapors and odors from the cook top area. For
best results, start the range hood before cooking and allow it to operate several minutes after the cooking is
completed to clear all smoke and odors from the kitchen.
• Button functions:
• Power: Power ON/OFF the range hood and activate power-off delay timer.
• Decrease Value: Blower (motor) speed decrease, timer value decrease, and enter timer mode.
• Increase Value: Blower (motor) speed increase timer value increase, and cumulative timer reset.
• Blower Power Indicator: Lights up when blower (motor) is running.
• Blower Speed Indicator: Shows current blower (motor) speed (1-6).
• Light Power Indicator: Lights up when lights turned on.
• Light: Turns ON/OFF and dim halogen lights.
• Power-On Elapsed Digital Timer: Indicates the accumulated time the system is running.
• Power-Off Delay Digital Timer: Indicates the length of time left for delay off function.
• Power-Off Delay Timer Indicator: Lights up when auto-shutdown delay timer function is on.
• Controls:
• Automatic cleaning reminder:
• This range hood is equipped with a cleaning reminder that will activate following 30 hours of use.
When blower (motor) starts to rotate, cumulative running time will be shown in Power-On Elapsed
Digital Timer. This timer icon flashes when 30 hours is up and reminds user to clean the aluminum
filter.
• After cleaning the filter and when the motor is not in use, press and hold Increase Value button over
3 seconds to reset the timer. Please note that turning off the system will not reset the Power-On
Elapsed Digital Timer.
• Adjusting the blower (motor) speed:
• Press Power button once to turn on the system. The Blower Power Indicator icon flashes showing
that the blower (motor) is ready. Decrease Value button will decrease the speed of the blower (mo-
tor) from 6 to 1 (strongest to quietest). Increase Value button will increase the speed of the blower
(motor) from 1 to 6 (quietest to strongest).
• Press Power button once to turn off the system.
Note: The system saves user configurations, hence settings such as light, timer and blower (motor) speed
will remain the same the next time it is turned on. Page 12
Range Hood Operations & Wiring Diagram (Continued)
Power Light
Decrease Value Increase Value
Blower Power Indicator Power-On Elapsed Digital Timer
Blower Speed Indicator Power-Off Delay Digital Timer
Light Power Indicator Power-Off Delay Timer Indicator
• Controls:
• Adjusting the timer function:
• While the blower (motor) is not running, press and hold Decrease Value button over 3 seconds to
enter timer mode. Adjust to desired period of delay off timer by pressing Increase Value or Decrease
Value button (minimum 1 minute to maximum 15 minutes). This setting will be saved immediately.
• Activating the timer function:
• While the blower (motor) is running, press and hold Power button for over 3 seconds to activate
delay off timer. Power-off delay indicator will lit up and power-off delay digital timer will begin to
countdown, when it reaches zero, the blower (motor) will shut down.
• Adjusting the light:
• Press Light button once to turn on the lights, and once again to turn off the lights.
• While the lights are off, press and hold Light button for over 3 seconds to dim the lights from low to
high. Level of brightness will be stored in system’s memory.
Note: Light settings are independent from other settings (including power-off delay) and lights has to be
manually turned on or off.
Note: The system saves user configurations, hence settings such as light, timer and blower (motor) speed
will remain the same the next time it is turned on.
Page 13
Range Hood Operations & Wiring Diagram (Continued)
Control type 1 - Touch Sensitive Version (Six speed with type GU10 bulb)
Control type 1 - Touch Sensitive Version (Six speed with type MR16 bulb)
12V/75W
Transformer
Page 14
Range Hood Operations & Wiring Diagram (Continued)
Control type 1 - Soft-Touch Version (Six speed with type GU10 bulb)
Control type 1 - Soft-Touch Version (Six speed with type MR16 bulb)
12V/75W
Transformer
Page 15
Range Hood Operations & Wiring Diagram (Continued)
Power Light
Power-Off Delay Increase Value
Decrease Value Power-Off Delay Digital Timer
Blower Speed Indicator Cleaning Reminder Indicator
The range hood is designed to remove smoke, cooking vapors and odors from the cook top area. For best results,
start the range hood before cooking and allow it to operate several minutes after the cooking is completed to clear
all smoke and odors from the kitchen.
• Button functions:
• Power: Power ON/OFF the range hood and activate power-off delay timer.
• Decrease Value: Blower (motor) speed decrease, timer value decrease, and enter timer mode.
• Increase Value: Blower (motor) speed increase, timer value increase, and cleaning reminder reset.
• Blower Speed Indicator: Shows current blower (motor) speed (1-4 or 1-6).
• Light: Turns ON/OFF and dim halogen lights.
• Power-Off Delay Digital Timer: Indicates the length of time left for delay off function.
• Controls:
• Automatic cleaning reminder:
• This range hood is equipped with a cleaning reminder that will activate following 30 hours of use. The
blower (motor) running time starts to accumulate when it first rotates, when the running time reached
30 hours, the Cleaning Reminder Indicator “C” flashes and reminds user to clean the range hood.
• After cleaning the filter and when the motor is not in use, press and hold Increase Value button over 3
seconds to reset the timer. Please note that turning off the system will not reset the Power-On Elapsed
Timer.
• Adjusting the blower (motor) speed:
• Press Power button once to turn on the system. The Blower Speed Indicator shows the blower (mo-
tor) speed level. Decrease Value button will decrease the speed of the blower (motor) from 4 or 6 to 1
(strongest to quietest). Increase Value button will increase the speed of the blower (motor) from 1 to
4 or 6 (quietest to strongest).
• Press Power button once to turn off the system.
Note: The system saves user configurations, settings such as light, timer and blower (motor) speed will re-
main the same the next time it is turned on.
Page 16
Range Hood Operations & Wiring Diagram (Continued)
Power Light
Power-Off Delay Increase Value
Decrease Value Power-Off Delay Digital Timer
Blower Speed Indicator Cleaning Reminder Indicator
• Controls:
• Adjusting the timer function:
• While the blower (motor) is not running, press and hold Decrease Value button over 3 seconds to
enter timer mode. Adjust to desired period of delay off timer by pressing Increase Value or Decrease
Value button (minimum 1 minute to maximum 9 minutes). This setting will be saved immediately.
• Activating the timer function:
• While the blower (motor) is running, press and hold Power button for over 3 seconds to activate
delay off timer. Power-Off Delay Digital Timer begin to countdown, when it reaches zero, the blower
(motor) will shut down.
• Adjusting the light:
• Press Light button once to turn on the lights, and once again to turn off the lights.
• While the lights are off, press and hold Light button for over 3 seconds to dim the lights from high to
low. Level of brightness will be stored in system’s memory.
CAUTION: DO NOT touch the lights until switched OFF and cooled.
Note: Light settings are independent from other settings (including power-off delay) and lights has to be
manually turned on or off.
Note: The system saves user configurations, settings such as light, timer and blower (motor) speed will re-
main the same the next time it is turned on.
Page 17
Range Hood Operations & Wiring Diagram (Continued)
12V/75W
Transformer
Page 18
Troubleshooting
1. If the range hood or halogen light does not operate • Check if the range hood has been plugged in, make
after installation: sure that all power has been turned back ON, fused
not blown and all electrical wiring are properly con-
nected.
• Swap out light assembly to working ones to deter-
mine whether it is caused by defective bulbs. See
Replacing the light bulbs on Page 26.
2. The range hood vibrates when the blower is on: • The range hood might not have been secured prop-
erly on to the ceiling or wall.
3. The blower or fan seems weak: • Check that the duct sized used is at least 8” or 3-1/4
x 10”. Range hood WILL NOT function efficiently
with insufficient duct size. For example: 9” duct
over 8” hole and loosely secured.
• Check if duct is clogged or if damper unit (half-cir-
cular flapper) is not installed correctly or opening
properly. A tight mesh on a side wall cap unit might
also cause restriction to the air flow.
4. The lights work but the blower is not spinning at all, • The blower might be jammed or scraping the bot-
is stuck or is rattling. tom due to shipping damage. Please contact us im-
mediately.
5. The hood is not venting out properly: • Make sure the distance between the stove top and
the bottom of the hood is within* 28” and 31” in
distance. *Due to different ceiling height configura-
tions, recommended height may not be applicable.
• Reduce the number of elbows and length of duct
work. Check if all joints are properly connected,
sealed, and taped.
• Make sure the power is on high speed for heavy
cooking.
NOTE: For all other inquiries, please contact your local reseller.
Page 19
Use and Care Information
Operations:
• Read and understand all instructions and warnings in this manual before operating the appliance. Save these
instructions for future reference.
• Always leave safety grills and filters in place. Without these components, operating blowers could catch on to
hair, fingers and loose clothing.
• NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into blowers.
• NEVER leave cooking unattended. When frying, oil in the pan can easily overheat and catch fire. The risk of
self combustion is higher when the oil has been used several times.
• NEVER cook on “open” flames under the range hood. Check deep-fryers during use: Superheated oil may be
flammable.
Cleaning:
• The saturation of greasy residue in the blower and filters may cause increased inflammability. Keep unit clean
and free of grease and residue build-up at all times to prevent possible fires.
• Filters must be cleaned periodically and free from accumulation of cooking residue (see cleaning instructions
on Page 26). Old and worn filters must be replaced immediately.
• DO NOT operate blowers when filters are removed. Never disassemble parts to clean without proper instruc-
tions. Disassembly is recommended to be performed by qualified personnel only. Read and understand all
instructions and warnings in this manual before proceeding.
Specifications
Specifications3:
Body Design Seamless Stainless Steel, Satin Finish
Power Rating 220V/50Hz or 120V/60Hz (USA & Canada Standard)
General Input Power 430W (360W + 2x35W) or 790W (2x360W + 2x35W)
Motor Input Power 360W per Blower
Levels Of Speed Control 4 Levels or 6 Levels
Airflow1 1000CFM (Single Motor) or 1400CFM (Dual Motor)
Noise Level2 1.4Sone (45dB) to 8.0Sone (70dB) (Lowest to Highest Speed)
Number Of Motors Single or Dual Motor
Motor Type Dual Chamber Ultra Quiet
Fan Type Dual Centrifugal Squirrel Cage
Control Type Soft-Touch or Touch-Sensitive Control Panel
Filtration Type Stainless Steel Baffle Filter
Illumination 35W Maximum, Dimmable
Heating Lamp (Optional) 220V or 120V (USA & Canada), 250W Maximum
Venting Size Top Transition Rectangular to 8 Inches Round
Interference Protection Radio Frequency Interference Protected
1. In House Test Static Pressure “0”.
2. One sone is roughly equivalent to the sound of a refrigerator (1kHz) at 40 decibels.
3. Subject to change without notice, please contact your local reseller for details. Page 20
Measurements and Diagrams
Page 21
Measurements and Diagrams (Continued)
Page 22
Measurements and Diagrams (Continued)
Page 23
Range Hood Assembly:
No. Description No. Description
1 Hood Casing 13 Halogen Light
2 Ducting Transition 14 Screws
3 Screws 15 Gasket
4 Blower Assembly 16 Baffle Filter
5 Wiring Box Cover 17 Stainless Steel Spacer
6 Wiring Box 18 Baffle Filter Handle
7 Heat Lamp Socket (optional) 19 Screws
8 Screws 20 Switch Assembly
9 Heat Lamp Socket Box (optional) 21 Electrical Assembly
10 Oil Tunnel
11 Real Halogen Light / Heat Lamp Panel
12 Front Halogen Light Panel
Page 24
Blower Assembly:
No. Description No. Description
4.1 Air Chamber 4.5 Motor
4.2 Air Flow Grill 4.6 Right Squirrel Cage
4.3 Left Locknut 4.7 Right Locknut
4.4 Left Squirrel Cage 4.8 Air Chamber
Page 25
Maintenance
SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating!
For optimal operation, clean range hood and all baffle/spacer/filter/grease tunnel/oil container regularly. Regular care will
help preserve the appearance of the range hood.
Cleaning Exterior surfaces:
• Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent (e.g. Comet
Power Scruv®, EZ-Off® oven cleaner), or steel wool/scoring pads, which will scratch and damage the stainless steel
surface. For heavier soil use liquid degrease such as “Forumla 409®” or “Fantastic®” brand cleaner.
• If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting
cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. CAUTION: Do not
leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently
rub off any stubborn spots. Use dry soft towel to dry the hood.
• After cleaning, you may use non abrasive stainless steel polish such as 3M® or ZEP®, to polish and buff out the stainless
luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.
• DO NOT allow deposits to accumulate or remain on the hood.
• DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.
• DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel
for extended periods. Many of these compounds contain chemicals, which may be harmful. Rinse with water after ex-
posure and wipe dry with a clean cloth.
Cleaning Stainless Steel Baffle Filters:
IMPORTANT: Drain oil from oil containers before oil and residue overflow!
• The metal filters fitted by the factory are intended to filter out residue and grease from cooking. It need not be replaced
on a regular basis but are required to be kept clean.
• Filters should be cleaned after every 30 hours of use.
• Remove and clean by hand or dishwasher. Spray “Formula 409®” or equivalent degreasing detergent and leave to soak
if heavily soiled. Dry filters and re-install before using hood.
Replacing Filters:
• The stainless steel baffle filters are designed to last but are required to be replaced if damaged, please contact your local
reseller for replacement filters.
Replacing the light bulb:
• This range hood uses halogen bulb (please refer to the actual specification of the hood purchased):
USA/Canada:
35W Type MR16 12V / Type GU10 120V Align arrows on both rings
Europe and other Countries:
35W Type MR16 12V / Type GU10 220V
• Make sure the range hood is unplugged or turn OFF breaker.
• Make sure the lights are cool to touch, carefully align the ar-
row on the inner ring with the arrow on the outer ring where it
says OPEN. The inner ring will loosen and the light bulb will
be available for removal. Install a new halogen light bulb and
reverse the steps.
• Turn ON breaker and range hood to test for operation.
WARNING
Hazard of Burns!
Light bulb become extremely hot when turned on.
DO NOT touch bulb until switched off and cooled.
Touching hot bulbs could cause serious burns. Page 26
Warranty
The information in this document is subject to change without notice, please contact your local reseller for updated details. Page 27
Disclaimer
Carefully inspect all items for damages before accepting delivery. note any damages on the freight bill or
express receipt. request name and signature of the carrier’s agent and keep copy to support your claim. Upon
acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the carrier and file
a claim immediately. Failure to do so may result in the denial of your claim. The carrier will furnish you with
necessary forms for filing a claim.
Damages caused during transit are not covered under our warranty. Please contact us to file an insurance claim.
Please inspect contents of package(s) carefully upon receiving! We must be notified of any damages and/or
missing parts within five (5) days upon your receipt of package(s). Claims will not be accepted after five (5)
days. NOTE: Items were thoroughly tested and carefully packed in our factory before shipping.
Products must be returned in good working condition with ALL original parts and documentation packed in
ALL original cartons, fillers and shipping cartons. A restocking fee of 15% will be charged for all approved
return(s). Exchanges or returns may not be accepted if any packaging is missing.
Make sure to inspect the hood for damages and defects before installation. Appearance flaws of the hood found
after installation and not affecting hood performance is not covered under our warranty for returns or exchang-
es. Service visits not covered under warranty will carry a service charge.
Before Installation: Return for exchange or refund (please see above for acceptable returns).
After Installation: NO exchange or refund.
Contact Us
If you need any assistance, please contact your local reseller. Please have your order number and model of the
range hood ready. This information will help them better respond to your request.
If you need replacement parts, we recommend that you only use genuine parts. Our accessories and parts are
engineered and designed specifically for this series of range hood, each is rigorously tested assuring the utmost
in durability and reliability, providing a factory match, factory-installed appearance and functionality tailored to
each individual range hood model.
The information in this document is subject to change without notice, please contact your local reseller for updated details. Page 28
Your Notes
Page 29
Your Notes
Page 30
Euro-Kitchen, Inc.
2341 Industrial Parkway West
Hayward, CA 94545
Ph: 510.266.0099
Fax: 510.266.6630
http://www.euro-kitchen.com