IntelliFlow User Guide 875-0180-000 Rev C1
IntelliFlow User Guide 875-0180-000 Rev C1
IntelliFlow User Guide 875-0180-000 Rev C1
User Guide
Part No. 875-0180-000 Rev. C1
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Copyright Notice
Hemisphere GPS Precision GPS Applications Hemisphere GPS (2009). All rights reserved. No part of this manual may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Hemisphere GPS.
Trademarks
HEMISPHERE GPS, the Hemisphere GPS logo, CRESCENT, ECLIPSETM, COASTTM, e-DIF, OUTBACKTM, OUTBACK Guidance, OUTBACK Guidance CenterTM, OUTBACK STM, OUTBACK S-LiteTM, OUTBACK S2TM, OUTBACK 360TM. OUTBACK Steering GuideTM, OUTBACK HitchTM, SATLOC, the Satloc logo, eDrive, eDriveTCTM, Just Let GoTM, L-DifTM, BaseLineHDTM, AerialAceTM, AirStarTM, AirTracTM, GPSteerTM, LiteStar IITM, PocketMaxTM, PocketMax PCTM, Satloc M3TM, MapStar, IntelliFlow, Beeline, Contour LockTM, StsTM and VectorTM are proprietary trademarks of Hemisphere GPS. Other trademarks are the properties of their respective owners.
Patents
The OUTBACK STM and S-LiteTM automated navigation and steering guide system is covered by U.S. Patents No. 6,539,303 and No. 6,711,501. The OUTBACK HitchTM automated hitch control system is covered by U.S. Patent No. 6,631,916. The OUTBACK eDriveTC GPS assisted steering system is covered by U.S. Patent No. 7,142,956. Hemisphere GPS products may be covered by one or more of the following U.S. Patents: 6,111,549 6,549,091 6,876,920 7,292,186 7,429,952 6,397,147 6,631,916 7,142,956 7,373,231 7,437,230 6,469,663 6,711,501 7,162,348 7,400,956 7,460,942 6,501,346 6,744,404 7,277,792 7,400,294 6,539,303 6,865,465 7,292,185 7,388,539
Notice to Customers
Contact your local dealer for technical assistance. To find the authorized dealer near you, call or write us at:
Hemisphere GPS 4110 9th Street S.E. Calgary, Alberta, Canada T2G 3C4 Telephone number: Fax number: E-mail address: (403) 259-3311 (403) 259-8866 sales@hemispheregps.com
WARRANTY NOTICE
COVERED PRODUCTS. This warranty covers all products manufactured by Hemisphere GPS and purchased by the end purchaser (the "Products"), unless otherwise specifically and expressly agreed in writing by Hemisphere GPS. LIMITED WARRANTY. Hemisphere GPS warrants solely to the end purchaser of the Products, subject to the exclusions and procedures set forth below, that the Products sold to such end purchaser and its internal components shall be free, under normal use and maintenance, from defects in materials, and workmanship and will substantially conform to Hemisphere GPS's applicable specifications for the Product, for a period of 12 months from delivery of such Product to such end purchaser (the "Warranty Period"). Repairs and replacement components for the Products are warranted, subject to the exclusions and procedures set forth below, to be free, under normal use and maintenance, from defects in material and workmanship, and will substantially conform to Hemisphere GPS's applicable specifications for the Product, for 90 days from performance or delivery, or for the balance of the original Warranty Period, whichever is greater. EXCLUSION OF ALL OTHER WARRANTIES. The LIMITED WARRANTY shall apply only if the Product is properly and correctly installed, configured, interfaced, maintained, stored, and operated in accordance with Hemisphere GPS's relevant User's Manual and Specifications, AND the Product is not modified or misused. The Product is provided "AS IS" and the implied warranties of MERCHANTABILITY and FITNESS FOR A PARTICULAR PURPOSE and ALL OTHER WARRANTIES, express, implied or arising by statute, by course of dealing or by trade usage, in connection with the design, sale, installation, service or use of any products or any component thereof, are EXCLUDED from this transaction and shall not apply to the Product. The LIMITED WARRANTY is IN LIEU OF any other warranty, express or implied, including but not limited to, any warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, title, and non-infringement. LIMITATION OF REMEDIES. The purchaser's EXCLUSIVE REMEDY against Hemisphere GPS shall be, at Hemisphere GPS's option, the repair or replacement of any defective Product or components thereof. The purchaser shall notify Hemisphere GPS or a Hemisphere GPS's approved service center immediately of any defect. Repairs shall be made through a Hemisphere GPS approved service center only. Repair, modification or service of Hemisphere GPS products by any party other than a Hemisphere GPS approved service center shall render this warranty null and void. The remedy in this paragraph shall only be applied in the event that the Product is properly and correctly installed, configured, interfaced, maintained, stored, and operated in accordance with Hemisphere GPS's relevant User's Manual and Specifications, AND the Product is not modified or misused. NO OTHER REMEDY (INCLUDING, BUT NOT LIMITED TO, SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR CONTINGENT DAMAGES FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR PROPERTY, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS) SHALL BE AVAILABLE TO PURCHASER, even if Hemisphere GPS has been advised of the possibility of such damages. Without limiting the foregoing, Hemisphere GPS shall not be liable for any damages of any kind resulting from installation, use, quality, performance or accuracy of any Product. HEMISPHERE IS NOT RESPONSIBLE FOR PURCHASER'S NEGLIGENCE OR UNAUTHORIZED USES OF THE PRODUCT. IN NO EVENT SHALL HEMISPHERE GPS BE IN ANY WAY RESPONSIBLE FOR ANY DAMAGES RESULTING FROM PURCHASER'S OWN NEGLIGENCE, OR FROM OPERATION OF THE PRODUCT IN ANY WAY OTHER THAN AS SPECIFIED IN HEMISPHERE GPS'S RELEVANT USER'S MANUAL AND SPECIFICATIONS.
Hemisphere GPS is NOT RESPONSIBLE for defects or performance problems resulting from (1) misuse, abuse, improper installation, neglect of Product; (2) the utilization of the Product with hardware or software products, information, data, systems, interfaces or devices not made, supplied or specified by Hemisphere GPS; (3) the operation of the Product under any specification other than, or in addition to, the specifications set forth in Hemisphere GPS's relevant User's Manual and Specifications; (4) damage caused by accident or natural events, such as lightning (or other electrical discharge) or fresh/salt water immersion of Product; (5) damage occurring in transit; (6) normal wear and tear; or (7) the operation or failure of operation of any satellite-based positioning system or differential correction service; or the availability or performance of any satellite-based positioning signal or differential correction signal. THE PURCHASER IS RESPONSIBLE FOR OPERATING THE VEHICLE SAFELY . The purchaser is solely responsible for the safe operation of the vehicle used in connection with the Product, and for maintaining proper system control settings. UNSAFE DRIVING OR SYSTEM CONTROL SETTINGS CAN RESULT IN PROPERTY DAMAGE, INJURY, OR DEATH. The purchaser is solely responsible for his/her safety and for the safety of others. The purchaser is solely responsible for maintaining control of the automated steering system at all times. THE PURCHASER IS SOLELY RESPONSIBLE FOR ENSURING THE PRODUCT IS PROPERLY AND CORRECTLY INSTALLED, CONFIGURED, INTERFACED, MAINTAINED, STORED, AND OPERATED IN ACCORDANCE WITH HEMISPHERE GPS'S RELEVANT USER'S MANUAL AND SPECIFICATIONS. Hemisphere GPS does not warrant or guarantee the positioning and navigation precision or accuracy obtained when using Products. Products are not intended for primary navigation or for use in safety of life applications. The potential accuracy of Products as stated in Hemisphere GPS literature and/or Product specifications serves to provide only an estimate of achievable accuracy based on performance specifications provided by the satellite service operator (i.e. US Department of Defense in the case of GPS) and differential correction service provider. Hemisphere GPS reserves the right to modify Products without any obligation to notify, supply or install any improvements or alterations to existing Products. GOVERNING LAW. This agreement and any disputes relating to, concerning or based upon the Product shall be governed by and interpreted in accordance with the laws of the State of Arizona. OBTAINING WARRANTY SERVICE. In order to obtain warranty service, the end purchaser must bring the Product to a Hemisphere GPS approved service center along with the end purchaser's proof of purchase. Hemisphere GPS does not warrant claims asserted after the end of the warranty period. For any questions regarding warranty service or to obtain information regarding the location of any of Hemisphere GPS approved service center, contact Hemisphere GPS at the following address: Hemisphere GPS 8444 N. 90th Street, Suite 130 Scottsdale, AZ 85258 Phone: 480-348-9919 Fax: 480-348-6370 techsupport@hemispheregps.com www.hemispheregps.com Documentation Feedback Hemisphere GPS is committed to the quality and continuous improvement of our products and services. We urge you to provide Hemisphere GPS with any feedback regarding this guide by writing to the following email address: DocFeedback@hemispheregps.com
Contents
Chapter 1 Chapter 2 Introducing IntelliFlow Whats Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installing IntelliFlow Important Safety Considerations . . . . . . . . . . . . . . . . 6 Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . 7 Mounting the Components . . . . . . . . . . . . . . . . . . . . 8 Connecting the Cables (M3) . . . . . . . . . . . . . . . . . . . 11 Connecting the Cables (Flying Flagman) . . . . . . . . 14 Connecting the Spray-Off Relay and Power . . . . . . 16 Calibrating the Pressure Switch (Optional) . . . . . . . 17 Chapter 3 Installing IntelliFlow Dual Rate Mounting the Components . . . . . . . . . . . . . . . . . . . 20 Connecting the Cables . . . . . . . . . . . . . . . . . . . . . . . 21 Chapter 4 Chapter 5 Activating Your Subscription (M3) Setting Flow Control Options Setting IntelliFlow Options (M3) . . . . . . . . . . . . . . . 28 Setting IntelliFlow Dual Rate Options (M3) . . . . . . . 33 Setting IntelliFlow Options (Flying Flagman) . . . . . 38 Chapter 6 Troubleshooting Common Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Testing the Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Chapter A Appendix Technical Specifications . . . . . . . . . . . . . . . . . . . . . . 50
vi
1: Introducing IntelliFlow
he new Air IntelliFlow Dual Rate option enables you to spray variable rate jobs in less time and in fewer trips. It does this by enabling you to spray two applications at the same time.
The basic IntelliFlow allows you to spray a constant rate or a variable rate job. The optional IntelliFlow Dual Rate enables you to: Spray a constant rate and a variable rate job simultaneously. Maintain droplet size when spraying constant Ultra Low Volume (ULV) rates. Mix two different applications at the end of the spray nozzle on the same swath. Spray one rate for most of a field and another rate for spot spraying where the crop is in need of special treatment to increase the yield. Switch back and forth between variable rate and constant rate jobs as needed.
The Hemisphere GPS flow control solution has proven to be rugged, efficient, reliable, and most importantly, flexible. The IntelliFlow Dual Rate option allows you to interface to any valve size and monitor a wide range of turbine flows. Because you are operating two controllers, you can independently operate two control valves and two spray-off relays, while monitoring two flow turbines. Using the Hemisphere GPS IntelliFlow system is easy. Upload your prescription maps using MapStar and select them from the M3s cockpit display. Alternatively, you can enter your own flow control parameters.
Figure 1-1: IntelliFlow meter, valve, and controller. Optional IntelliFlow Dual Rate meter, valve, and controller not pictured.
Whats Included
Below is the parts list for the IntelliFlow system. Please check your parts to make sure you have everything before beginning installation.
Item IntelliFlow Controller Spray-Off Relay Valve/Motor Assembly (2) Meter (2) Cable (IntelliFlow - M3, AUX, Flow Meter, Spray-Off Relay) Cable (IntelliFlow - Flying Flagman, AUX, Flow Meter, Spray-Off Relay) Cable (IntelliFlow - Motor/Valve) User Guide Part Number 806-1020-000 900-3040-000 806-1025-000 806-1025-000 051-0163-222 Qty 1 1 1 1 1
051-0204-222
054-0110-222 875-0180-000
1 1
1: Introducing IntelliFlow
Item IntelliFlow Controller Spray-Off Relay Valve and Motor Assembly (2) **Valve and Motor Assembly (1/2) *Valve and Motor Assembly (1) Flow Meter (2) **Flow Meter (1/2) *Flow Meter (3/4) **Cable (Ultra-Low Volume Adaptor) Cable (IntelliFlow Dual Rate - M3, AUX, Flow Meter, Spray-Off Relay) Cable (IntelliFlow - Motor/Valve) Cable (IntelliFlow - Power) Pressure Switch, Aircraft 10 Amp Circuit Breaker User Guide
Part Number 806-1020-000 900-3040-000 806-1025-000 710-0060-000 806-1032-000 900-3026-000 750-0046-000 710-0059-000 051-0173-000 051-0170-000
Qty 2 2 1 1 1 1 1 1 1 1
2 2 2 2 1
Notes: *Available with 1 Intelliflow Dual Rate Kit. **Available with 1/2 Ultra-Low Volume Intelliflow Dual Rate Kit.
2: Installing IntelliFlow
3.
Warning! If you do not maintain your system and find the flow turbine unit gummed up, you may have to remove the unit and clean it on the bench. This requires disassembling the unit and reassembling it. 4. When using highly corrosive products, protect the valve stem by lubricating it with a few drops of pneumatic turbine lubricating oil or, if not available, low-viscosity lubricating oil every 20 to 30 hours of spray time. This will avoid gumming and/or chemical corrosion buildup around valve stem and/or gland sealing components.
Tip! Apply penetrating oil, if required. Use products such as WD-40 or any quality penetrating oil before lubricating. 5. Do not tighten the valve stem gland-retaining nut unless you know how it is sealed. Any incorrect adjustment to the tension of the gland-retaining nut can adversely change the torque required to rotate the valve stem. This will cause the motor valve transmission and/or motor to over work, possibly causing damage.
Warning! If the valve stem starts to gum-up, the motor valve will not be able to respond to the IntelliFlow commands correctly. A tight valve stem can cause excessive current through the power IC chip inside the IntelliFlow controller.
Required Tools
Installing IntelliFlow requires the following tools: electric drill and 3/16 and 5/32 drill bits hacksaw thread sealant to prevent leakage hose or flange clamps (12) support straps (1 - 2). A stainless wrap-around strap and supporting piece is recommended.
2: Installing IntelliFlow
Other configurations are possible, but see the Caution note on the next page.
Note: If using IntelliFlow Dual Rate, you will install a second flow meter and motor/valve assembly next to the first one. See Chapter 3 for details.
Caution! Install the flow meter before the valve to avoid turbulence around the flow meter. If you cannot install the units in the recommended configuration due to physical limitations in your aircraft, you may invert the units. To reduce turbulence, maintain the following minimum hose length-todiameter ratios: hose between strainer and flow meter (10:1) hose between flow meter and motor/valve assembly (5:1)
2: Installing IntelliFlow
To install the flow meter and motor/valve 1. Measure and cut the hoses needed to connect the strainer to the flow meter, the flow meter to the motor/valve assembly, and the motor/valve assembly to the boom. Connect the hoses using hose clamps. Use two clamps at each connection point (refer to Figure 2-1. ). Warning! Place the meter at least 10 from the valve to minimize turbulence around the flow meter. See the Caution note above. 3. Attach the IntelliFlow assembly to the boom supply plumbing.
2.
Note: The completed IntelliFlow assembly will be installed in the middle of your boom supply tube. 4. Install one or two support fittings from the belly of the aircraft close to the valve and flow meter. Warning! Do not connect fittings directly to the valve or meter. Use a stainless wrap-around strap and supporting piece.
10
11
2: Installing IntelliFlow
Power 11 - 32 VDC 10 Amp breaker IntelliFlow Controller (806-1020-000) Power Motor Aux
*Spray relay Pump *Refer to Connecting the Spray-Off Relay and Power Manual override bypass switch
Note: Cable connection details for the spray-off relay and power are detailed in Figure 2-5 on page 16. ** See Figure 2-3 on page 13 for the Boom Pressure Switch wiring details.
12
(075-0035-222)
13
2: Installing IntelliFlow
14
Warning! Avoid shorts to the ground which will damage the IntelliFlow control unit and/or motor control unit. Check the grounding cable and lugs. Do not coil or pinch cables. This will introduce noise into the system and/or destroy the cable. Secure all cables to avoid the effects of excessive vibration. Do not place stress on the cable connectors. Store excess cable length with a minimum 6-inch bend radius. Avoid high-temperature exposure (exhaust, manifold, etc.) when routing cables. Avoid running cables where they will interfere with normal operation of the aircraft. Avoid placing cables close to sources of interference.
Notes: Connections for Cable 05-F-2006: Red wire - Pin 11 of DB25 connector Black wire - Pin 12 of DB25 connector Do not connect cable shield to anything. The Micronair flow meter can be used without the Micronair monitor. Use Cable 051-0208-222 in this case. The system bypass switch, part number 075-3019-222, comes with Cable 054-0110-222. Set the pressure switch to operate between 12 and 15 psi.
15
2: Installing IntelliFlow
10 Amp CB
Brake control interface box Aircraft ground Aircraft pump/ fan brake
Manual switch
16
Note: The switch is N/O (Normally Open); The contacts will close when the required pressure is correct.
17
2: Installing IntelliFlow
18
o install the IntelliFlow Dual Rate system, follow the installation instructions for IntelliFlow in Chapter 2 with the following exceptions:
Mount a second controller and a second flow meter and motor/ valve assembly. Follow the instructions for connecting the cables for the IntelliFlow Dual Rate in this section.
It is very important that you follow the instructions listed in Chapter 2 under: Important Safety Considerations Planning the Installation
20
Pump
Pump
Meter
Meter
Motor/ valve
Motor/ valve
To spray boom
21
22
Y
1.
ou must activate your subscription to access the variable rate and/ or IntelliFlow Dual Rate options if using the M3. Without activating your subscription, you will only be able to fly single hopper, constant rate jobs.
To activate your subscription Select Setup > Setup > Setup > Subscription Authorizations to access the Subscription Authorizations screen.
24
2.
From the Subscription Authorizations screen, select the feature you want to activate and enter your subscription number. a. b. In the Select Subscription field, select the feature you are activating from the drop-down menu. In the Enter CS Subscription # field, enter your subscription number.
Note: If you did not receive a subscription number at your time of purchase, please call Hemisphere GPS Technical Support at 480-3489919.
25
c.
Verify that you entered the correct subscription number by selecting Accept Subscription #.
4.
Repeat the above steps for each feature you wish to activate.
26
The screen displays the following message indicating installation was successful: Controller FOUND. Note: If the Controller NOT FOUND message appears, click the RESET button to search for installed controllers.
28
2.
From the AirTrac Setup screen, select SETUP > Flow Control to access the Flow Control Setup screen.
29
3.
From the Flow Control Setup screen, set your basic flow control options.
Controller type is automatically detected. Select the type of spray job constant or variable rate. Select application type: liquid or dry. Enter a target rate if flying a constant rate spray job. Import Prescription Map if flying a variable rate spray job. *Enter beginning volume Select Setup to access the Advanced Flow Control Setup screen for: - meter calibration - flow lead time (on/off), and - valve testing (see Appendix).
30
4.
Select to set controller parameters. Lead time represents how early the flow control will react to reach the proper rate at the proper location. Adjust defaults if necessary.
5.
Set the controller parameters from the Flow Controller Parameters screen.
31
Enter the factory calibration factor from the meter (k factor) - 3%.
Enter your target rate. Press to reset the hopper volume.
32
The two-controller system allows you to fly a constant and variable rate spray job simultaneously. For example, perhaps you need to spray one rate for most of the field, but spray a different rate for certain areas. You can set your primary target rate using the primary controller and designate the areas needing heavier spraying by using a prescription map with the secondary controller. IntelliFlow Dual Rate also provides you with the flexibility to switch back to a single, constant or variable rate job by disabling the secondary hopper from the main flow control setup screen. This section covers: Setting flow control options for dual controllers (constant and variable rate spray jobs) Disabling the secondary controller for single constant or variable rate jobs
33
To set flow control options for dual controllers (constant and variable rate) 1. Turn on the M3 system. The AirTrac Setup screen appears:
The screen displays the following messages indicating installation was successful: IntelliFlow Dual Rate Detected in the top left corner. Controller FOUND at the bottom of the screen.
Note: If the Controller FOUND message does not appear, click the RESET button to search for installed controllers.
34
2.
From the AirTrac Setup screen, select SETUP > Flow Control to access the Flow Control Setup screen.
3.
Controller type is automatically detected. Select application type: liquid or dry. Enter a target rate for the primary hopper. Import a Prescription Map for the secondary hopper. This will control your target rate.
From the Flow Control Setup screen, set your flow control options for the primary hopper.
Select Setup > Set Controller Parameters to set controller parameters for the secondary hopper.
Enter beginning volume for the Reset Total Area primary hopper. Volume Reset volume for when starting a hopper 1 here. The for the secondary reset volume button new spray job. hopper is set in the IntelliFlow for the secondary Dual Rate Controller hopper is in the Parameters screen. IntelliFlow Dual
Rate Controller
35
Notes: If using the IntelliFlow Dual Rate system, you must import the Prescription Map for the secondary controller here on the main Flow Control Setup screen. In the Mode field, AUTO automatically searches for and finds the controller type you have connected (if supported). Selecting DUAL will speed up initialization. SINGLE will disable the secondary controller, so do not select this if flying a two-controller job. 4. Select Setup > Set Controller Parameters to access the IntelliFlow Dual Rate Controller Parameters screen.
36
5.
Set the controller parameters for Controller 2 from the IntelliFlow Dual Rate Controller Parameters screen. Notice that each controller has its own set of spray options.
Set Auto Boom to YES for Dual Flow. Notice the Target Rate button is grayed out for the secondary controller. The secondary controller requires a prescription map. You cannot select a prescription map from this screen. you must return to the Flow Control Setup screen to import a prescription map.
Enter the factory calibration factor from the meter (k factor) - 3%.
Warning! If, while using the secondary controller, the Target Rate field displays N/A, you must return to the Flow Control Setup screen to import a prescription map. Notice that the Target Rate button is grayed out for the secondary controller. You cannot select a prescription map from this screen. you must return to the Flow Control Setup screen to import a prescription map. To set flow control options for a single controller (constant or variable rate) 1. 2. Follow steps 1 - 3 in the previous section to set your flow control options for the primary hopper. In the Flow Control Setup screens Mode field, select SINGLE.
37
2.Enter the beginning hopper volume. a. From the Flow Menu, select Load Tank. The TANK SIZE screen appears:
b.
Note: The remaining volume amount is displayed on the Run screen by REM.
38
3.
Enter your target flow rate. a. From the Flow Menu, select Set App Rate. The FLOW RATE screen appears:
b.
Note: The flow rate is displayed on the Run screen by APP or APPLICATION FLOW RATE 4. (Optional) Change the turnaround delay (TAD). The TAD is the additional reversal time (in milliseconds) given to the IntelliFlow motor when reversing direction. The default rate is 40 ms. a. To enter a turnaround delay, enter 0 for the rate in the FLOW RATE screen (step 3, above). The FLOW TAD screen appears:
b.
39
5.
Set the calibration factor. a. From the Flow Menu, select Set Cal Factor. The FLOW CALFAC screen appears:
b.
Note: The calibration factor is the factory calibration number found on the meter minus 3%. 6. Select IntelliFlow as your controller. a. From the Flow Menu, select Select Device. The FLOW SELECT screen appears:
b.
Press Enter to select, or the arrow key if IntelliFlow is not the controller shown here.
40
Chapter 6: Troubleshooting
Common Issues Testing the Valve
6: Troubleshooting
Common Issues
Common issues addressed in this section include: No Power When Initialize System Valve Does Not Open Meter Does Not Work Motor Does Not Rotate Flow Data Is Not Displayed on the Run Screen
Note: Voltage sent to the Normal/bypass switch from the IntelliFlow controller does not pass through the 10 Amp fuse on the controller. This is a security feature in case the IntelliFlow controller malfunctions, allowing the control valve motor to rotate to the open position. b. Check for other fuse problems: aircraft battery state (common problem) aircraft-IntelliFlow cable installation
42
3.
aircraft-IntelliFlow grounding connections aircraft battery charging system (e.g., alternator, regulator, etc.)
Check all wiring connections and terminal strips Warning! Avoid shorts to ground which will damage the IntelliFlow controller and/or motor controller. Check the IntelliFlow controller grounding cable and grounding lugs.
Note: The valve will not move if the pressure switch is stuck in the closed position. a. b. Remove the Aux switch I/O connector plug, where the pressure switch connects, from the IntelliFlow controller. Reset the system and check for normal operation. Normal operation indicates a problem with the pressure switch.
43
6: Troubleshooting
b.
Generate pulses by passing or tapping an iron object over the pick-up point of the sensor.
Note: These simulated pulses are not sufficient for accurate testing, but are sufficient for checking cables, IntelliFlow control unit I/O ports, interface between the IntelliFlow control unit and the M3, and general display operation. Adjust for 200 Hz square wave, amplitude close to 150 mv, 0 offset. If a simple function generator is available, connect it to the sensor connector to produce pulses. Warning! Do not install fuses greater than 10 Amps for the IntelliFlow control unit. A greater fuse value will cause internal damage to the IntelliFlow control unit. 1. Check the system for gummed up components. Turbine blades and the valve stem are susceptible to problems if proper maintenance isnt performed. Check that the motor, controller, sensor unit, and connector do not have water or chemicals inside.
2.
2.
44
45
6: Troubleshooting
To test the valve Note: If using IntelliFlow Dual Rate, you can test the valves and sprayoff relays for the primary and secondary controllers independently. The controller you are testing will be displayed on the screen. 1. From the Flow Control Advanced Setup menu, select Test Valve.
46
2.
Controller 1 selected
3. 4.
Press the Open and Close buttons. Notice the valve position numbers. Test the spray-off relay, if necessary. The unit will stay active for 5 ms.
47
6: Troubleshooting
*Valve position number: 3250 - fully closed 2650 - 1/4 open 2050 - 1/2 open 1550 - 3/4 open 1050 - fully open (*+/- 50)
Note: The valve position values can change according to valve type and size. 2. Press the Run Screen key to exit this screen.
48
Chapter A: Appendix
Technical Specifications Updating Firmware Wiring Pin-Out Connections
A: Appendix
Technical Specifications
Mechanical, power, and environmental specifications for the Hemisphere GPS IntelliFlow system and the optional IntelliFlow Dual Rate controller are provided below.
Table A-1: Mechanical Specifications - IntelliFlow Item IntelliFlow Controller Dimensions (in.) 11.7 L x 6.70 W x 2.38 H (29.7 L x 17.0 W x 6.03 H cm) 6.00 L x 2.60 W x 1.63 H (4.1 H x 15.2 L x 6.6 W cm) 5.50 L x 3.75 W x 10.00 H (25.4 H x 14.0 L x 9.5 W cm) 4.75 L x 3.25 W x 4.75 H (12.1 H x 12. 1 L x 8.3 W cm) Not provided. Cable lengths vary. Weight (lbs) 4.00 (1.8 kg) 5.00 (2.3 kg) 14.25 (6.5 kg) 4.00 (1.8 kg) 3.50 (1.6 kg)
Spray-Off Relay
Cables
Table A-2: Mechanical Specifications - Optional IntelliFlow Dual Rate Controller Item IntelliFlow Dual Rate Controller Spray-Off Relay Dimensions (inches) 11.70 L x 6.70 W x 2.38 H (29.7 L x 17.0 W x 6.0 H cm) 6.00 L x 2.60 W x 1.63 H (15.2 L x 6.6 W x 4.1 H cm) 5.50 L x 3.75 W x 10.00 H (12.7 L x 9.5 W x 25.4 H cm) 4.00 L x 4.00 W x 7.00 H (10.2 L x 10.2 W x 17.8 H cm) Weight (lbs) 4.00 (1.8 kg) 5.00 (2.3 kg) 14.25 (6.5 kg) 4.25 (1.9 kg)
Valve and Motor Assembly (2) Valve and Motor Assembly (1/2)
50
Table A-2: Mechanical Specifications - Optional IntelliFlow Dual Rate Controller Item Meter (2) Dimensions (inches) 4.75 L x 3.25 W x 4.75 H (12.1 L x 8.3 W x 12.1 H cm) 4.00 L x 2.13 W x 3.75 H (12.1 L x 5.4 W x 9.5 H cm) Not provided. Cable lengths vary. Weight (lbs) 4.00 (1.8 kg) 2.00 (0.9 kg) 7.00 (3.2 kg)
Meter (3/4)
Cables
Table A-3: Power Specifications - IntelliFlow Controller Specification Inverse Voltage Protection Over Current and/or Short Circuit Protection Operating Voltage Maximum Working Current Maximum Transient Current Nominal Operating Current Range Description Yes Yes
Table A-4: Power Specifications - Spray-Off Relay Specification Inverse Voltage Protection Over Current and/or Short Circuit Protection Operating Voltage Description Yes Yes
11 - 60 VDC
51
A: Appendix
Table A-4: Power Specifications - Spray-Off Relay Maximum Working Current Maximum Transient Current Nominal Operating Current Range 7 Amps 10 Amps 0.1 to 6 Amps
Table A-5: Environmental Specifications Operating Temperature Storage Temperature Humidity Resistance -4 to + 140 F (-20 to +60 C) -40 to + 176 F (-40 to +80 C) 95% non-condensing Dust and Water Vibration and Shock
52
Updating Firmware
This section describes the procedure to update firmware for both the M3 and the Flying Flagman.
Note: GPS speed must be less than 5 m/s and the system must recognize the *software version for the Load New Program button to be selectable. *The software version must be more recent than 1pF or 1rF .
53
A: Appendix
4.
5.
A status message displays, Please Wait, Rebooting IntelliFlow. The following screen then appears.
54
4.
Press Enter to abort the download process or wait to see the next screen.
5.
To download the new software from the PCMCIA card, please note that if the red LED light on the upper right corner of the shift key is illuminated, you press the Shift key twice and then press the Esc key. If the red LED light on the upper right corner of the shift key is not illuminated, you press the Shift key once and then press the Esc key. The keys must be press sequentially, not simultaneously, to initiate the download process.
55
A: Appendix
6.
7.
Verify that the update was successful. If so, the following screen appears:
8.
56
BLU/WHT, 22AWG Flow1 RED/WHT, 22AWG Flow1 + BLK/WHT, 22AWG GRD ORG/WHT, 22AWG Flow2 + WHT, 22AWG Flow1 + Shield BLU/WHT, 22AWG BLK/WHT, 22AWG RX M3 TX M3 GRD Shield RED/WHT, 22AWG BLU/WHT, 22AWG BLK/WHT, 22AWG ORG/WHT, 22AWG GRD 12+ RTS CTS
57
A: Appendix
Switch, 10A, IntelliFlow DPDT Motor/valve 7343K82 (075-3019-222) Detail B Label (677-1024-222)
Figure A-2: Cable 054-0110-222.
Shield GRN ORG WHT BLK IntelliFlow motor valve Bypass switch
ORG WHT/BLK stripe GRN/BLK stripe BRN/BLK stripe N/C P4 label Note 2PL BLU BLK WHT RED
58
Cable 051-0170-000 (IntelliFlow Dual Rate - Spray-Off Relay, AUX, M3, and Flow Meter)
59
A: Appendix
1 Swath advance (red) 2 Swath decrease 3 Break (orange) 4 Mark (green) 5 Resume (brown)
Warning! DO NOT connect the black ground wire to the aircraft ground or shield of the cable. DO NOT allow the black ground wire to touch any part of the fuselage. The black ground wire is the logic return ground for the GMUs remote switch functions. The black ground wire is used as the common return for the other remote switch wires. See the following figure for an example.
60
Pressure switch
61
A: Appendix
62
2.
c. d.
64
e. f. g. h. i. 3.
sub-license, rent, lease, loan or distribute the Software; permit any third party to use the Software; use or operate Product for the benefit of any third party in any type of service outsourcing, application service, provider service or service bureau capacity; reverse engineer, de compile or disassemble the Software or otherwise reduce it to a human perceivable form; Assign this Agreement or sell or otherwise transfer the Software to any other party except as part of the sale or transfer of the whole Product.
UPDATES. At Hemisphere's discretion Hemisphere may make Updates available to Licensee. An update ("Update") means any update to the Software that is made available to Licensee including error corrections, enhancements and other modifications. Licensee may access, download and install Updates during the Warranty Period only. All Updates that Licensee downloads, installs or uses shall be deemed to be Software and subject to this Agreement. Hemisphere reserves the right to modify the Product without any obligation to notify, supply or install any improvements or alterations to existing Software. SUPPORT. Hemisphere may make available directly or through its authorized dealers telephone and email support for the Software. Contact Hemisphere to find the authorized dealer near you. As well, Hemisphere may make available user and technical documentation regarding the Software. Hemisphere reserves the right to reduce and limit access to such support at any time. BACKUPS AND RECOVERY. Licensee shall back-up all data used, created or stored by the Software on a regular basis as necessary to enable proper recovery of the data and related systems and processes in the event of a malfunction in the Software or any loss or corruption of data caused by the Software. Licensee shall assume all risks of loss or damage for any failure to comply with the foregoing. OWNERSHIP . Hemisphere and its suppliers own all rights, title and interest in and to the Software and related materials, including all intellectual property rights. The Software is licensed to Licensee, not sold. TRADEMARKS. "Hemisphere GPS", "Outback Guidance", "BEELINE", "Crescent", "Eclipse" and the associated logos are trademarks of Hemisphere. Other trademarks are the property of their respective owners. Licensee may not use any of these trademarks without the consent of their respective owners. LIMITED WARRANTY. Hemisphere warrants solely to the Licensee, subject to the exclusions and procedures set forth herein below, that for a period of one (1) year from the original date of purchase of the Product in which it is embedded (the "Warranty Period"), the Software, under normal use and maintenance, will conform in
4.
5.
6.
7.
8.
65
all material respects to the documentation provided with the Software and any media will be free of defects in materials and workmanship. For any Update, Hemisphere warrants, for 90 days from performance or delivery, or for the balance of the original Warranty Period, whichever is greater, that the Update, under normal use and maintenance, will conform in all material respects to the documentation provided with the Update and any media will be free of defects in materials and workmanship. Notwithstanding the foregoing, Hemisphere does not warrant that the Software will meet Licensee's requirements or that its operation will be error free. 9. WARRANTY EXCLUSIONS. The warranty set forth in Section (LIMITED WARRANTY. Hemisphere warrants solely to the Licensee, subject to the exclusions and procedures set forth herein below, that for a period of one (1) year from the original date of purchase of the Product in which it is embedded (the "Warranty Period"), the Software, under normal use and maintenance, will conform in all material respects to the documentation provided with the Software and any media will be free of defects in materials and workmanship. For any Update, Hemisphere warrants, for 90 days from performance or delivery, or for the balance of the original Warranty Period, whichever is greater, that the Update, under normal use and maintenance, will conform in all material respects to the documentation provided with the Update and any media will be free of defects in materials and workmanship. Notwithstanding the foregoing, Hemisphere does not warrant that the Software will meet Licensee's requirements or that its operation will be error free. will not apply to any deficiencies caused by (a) the Product not being used as described in the documentation supplied to Licensee, (b) the Software having been altered, modified or converted in any way by anyone other than Hemisphere approved by Hemisphere, (c) any malfunction of Licensee's equipment or other software, or (d) damage occurring in transit or due to any accident, abuse, misuse, improper installation, lightning (or other electrical discharge) or neglect other than that caused by Hemisphere. Hemisphere GPS does not warrant or guarantee the precision or accuracy of positions obtained when using the Software (whether standalone or embedded in a Product). The Product and the Software is not intended and should not be used as the primary means of navigation or for use in safety of life applications. The potential positioning and navigation accuracy obtainable with the Software as stated in the Product or Software documentation serves to provide only an estimate of achievable accuracy based on specifications provided by the US Department of Defense for GPS positioning and DGPS service provider performance specifications, where applicable.
10. WARRANTY DISCLAIMER. EXCEPT AS EXPRESSLY SET OUT IN THIS AGREEMENT, HEMISPHERE MAKES NO REPRESENTATION, WARRANTY OR CONDITION OF ANY KIND TO LICENSEE, WHETHER VERBAL OR WRITTEN AND HEREBY DISCLAIMS ALL REPRESENTATIONS, WARRANTIES AND CONDITIONS OF
66
ANY KIND INCLUDING FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, ACCURACY, RELIABILITY OR THAT THE USE OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE AND HEREBY DISCLAIMS ALL REPRESENTATIONS, WARRANTIES AND CONDITIONS ARISING AS A RESULT OF CUSTOM, USAGE OR TRADE AND THOSE ARISING UNDER STATUTE. 11. LIMITS ON WARRANTY DISCLAIMER. Some jurisdictions do not allow the exclusion of implied warranties or conditions, so some of the above exclusions may not apply to Licensee. In that case, any implied warranties or conditions which would then otherwise arise will be limited in duration to ninety (90) days from the date of the license of the Software or the purchase of the Product. The warranties given herein give Licensee specific legal rights and Licensee may have other rights which may vary from jurisdiction to jurisdiction. 12. CHANGE TO WARRANTY. No employee or agent of Hemisphere is authorized to change the warranty provided or the limitation or disclaimer of warranty provisions. All such changes will only be effective if pursuant to a separate agreement signed by senior officers of the respective parties. 13. WARRANTY CLAIM. In the event Licensee has a warranty claim Licensee must first check for and install all Updates that are made available. The warranty will not otherwise be honored. Proof of purchase may be required. Hemisphere does not honor claims asserted after the end of the Warranty Period. 14. LICENSEE REMEDIES. In all cases which involve a failure of the Software to conform in any material respect to the documentation during the Warranty Period or a breach of a warranty, Hemisphere's sole obligation and liability, and Licensee's sole and exclusive remedy, is for Hemisphere, at Hemisphere's option, to (a) repair the Software, (b) replace the Software with software conforming to the documentation, or (c) if Hemisphere is unable, on a reasonable commercial basis, to repair the Software or to replace the Software with conforming software within ninety (90) days, to terminate this Agreement and thereafter Licensee shall cease using the Software. Hemisphere will also issue a refund for the price paid by Licensee less an amount on account of amortization, calculated on a straight-line basis over a deemed useful life of three (3) years. 15. LIMITATION OF LIABILITY. IN NO EVENT WILL HEMISPHERE BE LIABLE TO LICENSEE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR INDIRECT DAMAGES INCLUDING ARISING IN RELATION TO ANY LOSS OF DATA, INCOME, REVENUE, GOODWILL OR ANTICIPATED SAVINGS EVEN IF HEMISPHERE HAS BEEN INFORMED OF THE POSSIBILITY OF SUCH LOSS OR DAMAGE. FURTHER, IN NO EVENT WILL HEMISPHERE'S TOTAL CUMULATIVE LIABILITY HEREUNDER, FROM ALL CAUSES OF ACTION OF ANY KIND, EXCEED THE TOTAL AMOUNT PAID BY LICENSEE TO HEMISPHERE TO PURCHASE THE PRODUCT. THIS LIMITATION AND
67
EXCLUSION APPLIES IRRESPECTIVE OF THE CAUSE OF ACTION, INCLUDING BUT NOT LIMITED TO BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, TORT, BREACH OF WARRANTY, MISREPRESENTATION OR ANY OTHER LEGAL THEORY AND WILL SURVIVE A FUNDAMENTAL BREACH. 16. LIMITS ON LIMITATION OF LIABILITY. Some jurisdictions do not allow for the limitation or exclusion of liability for incidental or consequential damages, so the above limitation or exclusion may not apply to Licensee and Licensee may also have other legal rights which may vary from jurisdiction to jurisdiction. 17. BASIS OF BARGAIN. Licensee agrees and acknowledges that Hemisphere has set its prices and the parties have entered into this Agreement in reliance on the limited warranties, warranty disclaimers and limitations of liability set forth herein, that the same reflect an agreed-to allocation of risk between the parties (including the risk that a remedy may fail of its essential purpose and cause consequential loss), and that the same forms an essential basis of the bargain between the parties. Licensee agrees and acknowledges that Hemisphere would not have been able to sell the Product at the amount charged on an economic basis without such limitations. 18. PROPRIETARY RIGHTS INDEMNITY. Hemisphere shall indemnify, defend and hold harmless Licensee from and against any and all actions, claims, demands, proceedings, liabilities, direct damages, judgments, settlements, fines, penalties, costs and expenses, including royalties and attorneys' fees and related costs, in connection with or arising out of any actual infringement of any third party patent, copyright or other intellectual property right by the Software or by its use, in accordance with this Agreement and documentation, PROVIDED THAT: (a) Hemisphere has the right to assume full control over any action, claim, demand or proceeding, (b) Licensee shall promptly notify Hemisphere of any such action, claim, demand, or proceeding, and (c) Licensee shall give Hemisphere such reasonable assistance and tangible material as is reasonably available to Licensee for the defense of the action, claim, demand or proceeding. Licensee shall not settle or compromise any of same for which Hemisphere has agreed to assume responsibility without Hemisphere's prior written consent. Licensee may, at its sole cost and expense, retain separate counsel from the counsel utilized or retained by Hemisphere. 19. INFRINGEMENT. If use of the Software may be enjoined due to a claim of infringement by a third party then, at its sole discretion and expense, Hemisphere may do one of the following: (a) negotiate a license or other agreement so that the Product is no longer subject to such a potential claim, (b) modify the Product so that it becomes non-infringing, provided such modification can be accomplished without materially affecting the performance and functionality of the Product, (c) replace the Software, or the Product, with non-infringing software, or product, of equal or better
68
performance and quality, or (d) if none of the foregoing can be done on a commercially reasonable basis, terminate this license and Licensee shall stop using the Product and Hemisphere shall refund the price paid by Licensee less an amount on account of amortization, calculated on a straight-line basis over a deemed useful life of three (3) years. 20. The foregoing sets out the entire liability of Hemisphere and the sole obligations of Hemisphere to Licensee in respect of any claim that the Software or its use infringes any third party rights 21. INDEMNIFICATION. Except in relation to an infringement action, Licensee shall indemnify and hold Hemisphere harmless from any and all claims, damages, losses, liabilities, costs and expenses (including reasonable fees of lawyers and other professionals) arising out of or in connection with Licensee's use of the Product, whether direct or indirect, including without limiting the foregoing, loss of data, loss of profit or business interruption. 22. TERMINATION. Licensee may terminate this Agreement at any time without cause. Hemisphere may terminate this Agreement on 30 days notice to Licensee if Licensee fails to materially comply with each provision of this Agreement unless such default is cured within the 30 days. Any such termination by a party shall be in addition to and without prejudice to such rights and remedies as may be available, including injunction and other equitable remedies. Upon receipt by Licensee of written notice of termination from Hemisphere or termination by Licensee, Licensee shall at the end of any notice period (a) cease using the Software; and (b) return to Hemisphere (or destroy and provide a certificate of a Senior Officer attesting to such destruction) the Software and all related material and any magnetic or optical media provided to Licensee. The provisions of Sections OWNERSHIP . Hemisphere and its suppliers own all rights, title and interest in and to the Software and related materials, including all intellectual property rights. The Software is licensed to Licensee, not sold. , TRADEMARKS. "Hemisphere GPS", "Outback Guidance", "BEELINE", "Crescent", "Eclipse" and the associated logos are trademarks of Hemisphere. Other trademarks are the property of their respective owners. Licensee may not use any of these trademarks without the consent of their respective owners., LIMITED WARRANTY. Hemisphere warrants solely to the Licensee, subject to the exclusions and procedures set forth herein below, that for a period of one (1) year from the original date of purchase of the Product in which it is embedded (the "Warranty Period"), the Software, under normal use and maintenance, will conform in all material respects to the documentation provided with the Software and any media will be free of defects in materials and workmanship. For any Update, Hemisphere warrants, for 90 days from performance or delivery, or for the balance of the original Warranty Period, whichever is greater, that the Update, under normal use and maintenance, will conform in all material respects to the documentation provided with the Update and
69
any media will be free of defects in materials and workmanship. Notwithstanding the foregoing, Hemisphere does not warrant that the Software will meet Licensee's requirements or that its operation will be error free. , WARRANTY EXCLUSIONS. The warranty set forth in Section (LIMITED WARRANTY. Hemisphere warrants solely to the Licensee, subject to the exclusions and procedures set forth herein below, that for a period of one (1) year from the original date of purchase of the Product in which it is embedded (the "Warranty Period"), the Software, under normal use and maintenance, will conform in all material respects to the documentation provided with the Software and any media will be free of defects in materials and workmanship. For any Update, Hemisphere warrants, for 90 days from performance or delivery, or for the balance of the original Warranty Period, whichever is greater, that the Update, under normal use and maintenance, will conform in all material respects to the documentation provided with the Update and any media will be free of defects in materials and workmanship. Notwithstanding the foregoing, Hemisphere does not warrant that the Software will meet Licensee's requirements or that its operation will be error free. will not apply to any deficiencies caused by (a) the Product not being used as described in the documentation supplied to Licensee, (b) the Software having been altered, modified or converted in any way by anyone other than Hemisphere approved by Hemisphere, (c) any malfunction of Licensee's equipment or other software, or (d) damage occurring in transit or due to any accident, abuse, misuse, improper installation, lightning (or other electrical discharge) or neglect other than that caused by Hemisphere. Hemisphere GPS does not warrant or guarantee the precision or accuracy of positions obtained when using the Software (whether standalone or embedded in a Product). The Product and the Software is not intended and should not be used as the primary means of navigation or for use in safety of life applications. The potential positioning and navigation accuracy obtainable with the Software as stated in the Product or Software documentation serves to provide only an estimate of achievable accuracy based on specifications provided by the US Department of Defense for GPS positioning and DGPS service provider performance specifications, where applicable. , WARRANTY DISCLAIMER. EXCEPT AS EXPRESSLY SET OUT IN THIS AGREEMENT, HEMISPHERE MAKES NO REPRESENTATION, WARRANTY OR CONDITION OF ANY KIND TO LICENSEE, WHETHER VERBAL OR WRITTEN AND HEREBY DISCLAIMS ALL REPRESENTATIONS, WARRANTIES AND CONDITIONS OF ANY KIND INCLUDING FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, ACCURACY, RELIABILITY OR THAT THE USE OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE AND HEREBY DISCLAIMS ALL REPRESENTATIONS, WARRANTIES AND CONDITIONS ARISING AS A RESULT OF CUSTOM, USAGE OR TRADE AND THOSE ARISING UNDER STATUTE., LIMITATION OF LIABILITY. IN NO EVENT WILL HEMISPHERE BE LIABLE TO LICENSEE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR INDIRECT DAMAGES INCLUDING ARISING IN RELATION TO ANY LOSS OF DATA, INCOME, REVENUE, GOODWILL OR
70
ANTICIPATED SAVINGS EVEN IF HEMISPHERE HAS BEEN INFORMED OF THE POSSIBILITY OF SUCH LOSS OR DAMAGE. FURTHER, IN NO EVENT WILL HEMISPHERE'S TOTAL CUMULATIVE LIABILITY HEREUNDER, FROM ALL CAUSES OF ACTION OF ANY KIND, EXCEED THE TOTAL AMOUNT PAID BY LICENSEE TO HEMISPHERE TO PURCHASE THE PRODUCT. THIS LIMITATION AND EXCLUSION APPLIES IRRESPECTIVE OF THE CAUSE OF ACTION, INCLUDING BUT NOT LIMITED TO BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, TORT, BREACH OF WARRANTY, MISREPRESENTATION OR ANY OTHER LEGAL THEORY AND WILL SURVIVE A FUNDAMENTAL BREACH., INDEMNIFICATION. Except in relation to an infringement action, Licensee shall indemnify and hold Hemisphere harmless from any and all claims, damages, losses, liabilities, costs and expenses (including reasonable fees of lawyers and other professionals) arising out of or in connection with Licensee's use of the Product, whether direct or indirect, including without limiting the foregoing, loss of data, loss of profit or business interruption. , FORUM FOR DISPUTES. The parties agree that the courts located in Calgary, Alberta, Canada and the courts of appeal there from will have exclusive jurisdiction to resolve any disputes between Licensee and Hemisphere concerning this Agreement or Licensee's use or inability to use the Software and the parties hereby irrevocably agree to abide to the jurisdiction of those courts. Notwithstanding the foregoing, either party may apply to any court of competent jurisdiction for injunctive relief. and APPLICABLE LAW. This Agreement shall be governed by the laws of the Province of Alberta, Canada, exclusive of any of its choice of law and conflicts of law jurisprudence. herein shall survive the expiry or termination of this Agreement for any reason. 23. EXPORT RESTRICTIONS. Licensee agrees that Licensee will comply with all export control legislation of Canada, the United States, Australia and any other applicable country's laws and regulations, whether under the Arms Export Control Act, the International Traffic in Arms Regulations, the Export Administration Regulations, the regulations of the United States Departments of Commerce, State, and Treasury, or otherwise as well as the export control legislation of all other countries. 24. PRODUCT COMPONENTS. The Product may contain third party components. Those third party components may be subject to additional terms and conditions. Licensee is required to agree to those terms and conditions in order to use the Product. 25. FORCE MAJEURE EVENT. Neither party will have the right to claim damages as a result of the other's inability to perform or any delay in performance due to unforeseeable circumstances beyond its reasonable control, such as labor disputes, strikes, lockouts, war, riot, insurrection, epidemic, Internet virus attack, Internet failure, supplier failure, act of God, or governmental action not the fault of the nonperforming party.
71
26. FORUM FOR DISPUTES. The parties agree that the courts located in Calgary, Alberta, Canada and the courts of appeal there from will have exclusive jurisdiction to resolve any disputes between Licensee and Hemisphere concerning this Agreement or Licensee's use or inability to use the Software and the parties hereby irrevocably agree to abide to the jurisdiction of those courts. Notwithstanding the foregoing, either party may apply to any court of competent jurisdiction for injunctive relief. 27. APPLICABLE LAW. This Agreement shall be governed by the laws of the Province of Alberta, Canada, exclusive of any of its choice of law and conflicts of law jurisprudence. 28. CISG. The United Nations Convention on Contracts for the International Sale of Goods will not apply to this Agreement or any transaction hereunder. 29. GENERAL. This is the entire agreement between Licensee and Hemisphere relating to the Product and Licensee's use of the same, and supersedes all prior, collateral or contemporaneous oral or written representations, warranties or agreements regarding the same. No amendment to or modification of this Agreement will be binding unless in writing and signed by duly authorized representatives of the parties. Any and all terms and conditions set out in any correspondence between the parties or set out in a purchase order which are different from or in addition to the terms and conditions set forth herein, shall have no application and no written notice of same shall be required. In the event that one or more of the provisions of this Agreement is found to be illegal or unenforceable, this Agreement shall not be rendered inoperative but the remaining provisions shall continue in full force and effect.
72