Weld Ring Gaskets 2
Weld Ring Gaskets 2
Weld Ring Gaskets 2
Weld-Ring Gaskets
Page 3
Common Materials
Page 4
Dimensions
Weld-Ring Gaskets
Weld-Ring Gaskets
Typical characteristics
Profiles
Compensation of
radial differential
expansion.
Standard
procedure
Not possible
Up to max. r ~5 mm
depends on hollow lip
wall thickness
Easy to dismantle
with a 2mm cut off
disc.
Can be re-welded up
to 4 times
Can be applied as an
additional intermittent
weld for further
fastening
Standard procedure
Up to max. r ~5 mm
depends on hollow lip
wall thickness
Easy to dismantle
with a 2mm cut off
disc.
Can be re-welded up
to 4 times
a) An additional
intermittent weld for
further fastening
b) If susceptible to
corrosion
a) Standard procedure
b) Additional fastening
through intermittent
weldments
Effect is small
because of the small
hollow lip
dimensions.
max. r ~ 0,5 mm
a) An additional
intermittent weld for
further fastening
b) If susceptible to
corrosion
a) Standard procedure
b) Additional fastening
Befestigungshilfe.
through intermittent
weldments
hardly possible
max.. r ~ 0,1 mm
Not possible.
Additionally flange
form M to DIN 2526
required
Difficult to dismantle.
Can be re-welded up
to 3 times
Use cut-off disc.
Material loss 2-3 mm
each.
Can be rewelded
up to 5 times
Use cut-off disc.
Material loss 2-3 mm
each.
Can be rewelded
up to 5 times
It is recommended to use weld-ring gaskets for any application where it is absolutely necessary to have a leak proof
joint, and also a limited opportunity for disassembling is
required. Underlying reasons for this requirement may be
containment of hazardous materials or the need for a
shutdown free operation.
The limited opportunity for disassembling mean in this
case, that the bolts have to be removed and the weld seam
has to be cut besides. The gasket can be reused and
rewelded up to five times depending on gasket type.
Gasket materials are generally the same or similar to the
pipe or flange material. Weld-ring gaskets can only be
used in pairs.
Depending on requirements a gasket profile is to select
from previously shown table. In the overview, the selection
criteria are shown versus typical characteristics for profiles
A21 to A25.
The welded connection between one half of the weld-ring
gasket and one flange is defined as welded joint in the
following text. The welded joint can either be an inside or
outside weld, or even be a combination of both. The
welding connection of the two gasket halves to each other
is defined as seal-weld.
Weld-Ring Gaskets
Characteristics
Safety instruction:
Weld-ring gaskets with hollow lip profiles A24 and A25
sometimes have the tendency to build up condensation,
which can expand due to sudden temperature rises. In
order to prevent this, the design of each gasket-half has 4
radial grooves, 1.5mm deep and 3mm wide.
Profile
Cross-Section
A23
A24
A24H
A24K
A25
Weld-Ring Gaskets
A24KVR
Profile A24KVR with male and female designs. The female part is designed as a grooved gasket.
Weld-Ring Gaskets
Layers for this gasket are PTFE, graphite, silver or, AFS*
depending on design requirements. Thickness of layer
0.5 mm.
Profile A24N is designed with a groove to accommodate
a profile SpV3N spiral wound gasket. Materials of construction available are listed in brochure "Spiral Wound
Gaskets SPIROFLEX".
Spiral wound gasket SpV3N in the main load
A24N
Profile
A22
A22H
Cross-Section
A22K
A22KVR
A24R + B27A
A22N
Cross-Section
A21
Material abbreviation
EN 10 027-1
Material-No.
EN 10 027-2
Temperature
of Medium
S235JRG2
1.0038
bis 4250C
16Mo3
1.5415
13CrMo4-5
1.7335
10CrMo9-10
1.7380
X6CrNiTi18-10
1.4541
X6CrNiMoTi17-12-2
1.4571
max. 5500C
Weld-Ring Gaskets
Profile A21
Profile A24
Profile A21
Profile A24
Weld-Ring Gaskets
Dimension Table
Dimension Table
Dimensions in mm
DN
d23) for PN
d1
63
100
160
250 u. 320
400
d32)
80
90
143
149
149
153
153
123
100
115
169
176
176
179
179
149
125
142
206
213
213
216
216
186
150
165
243
248
248
248
248
218
200
214
305
315
315
315
315
285
Dimensions in mm
250
264
360
370
370
370
340
300
310
420
430
430
400
460
400
386
539
519
NPS
d1
150
d32)
122
157
186
216
270
324
381
- 413 413
413
- 470 470
470
25
d2
d1
40
d2
d1
63
d2
d1
100
d2
d1
d2
250
- 258 389
300
- 306 456
350
400
500
655
702
600
- 598 729
745
762
811
700
- 696 831
850
877
948
800
- 795 940
900
- 892 1040
1362
972
1082
1192
1396
986
1106
1218
1450
570
to be specified
by purchaser**
490
16
d1
to be specified
by purchaser**
482
DN
to be specified
by purchaser**
340
PN
to be specified
by purchaser**
350
1576
1616
1796
1828
1998
2228
1)
Weld-Ring Gaskets
Dimension Table
Dimensions in mm
PN 10 40
DN
10
15
20
25
32
40
50
65
80
100
125
150
(175)
200
250
d2
d3
27
32
38
46
55
60
75
90
105
125
150
178
210
235
285
41
46
58
66
75
80
95
110
125
145
170
198
230
255
305
d1
13,6
17,3
22,3
28,5
37,2
43,1
54,5
70,3
82,5
107,1
131,7
159,3
182,5
206,5
258,8
PN 63
d1
13,6
17,3
28,5
37,2
42,5
54,5
69,7
81,7
106,3
130,7
157,1
181,1
204,9
255,4
PN 100
d2
d3
30
35
50
55
60
75
90
105
125
150
178
210
235
285
50
55
70
75
80
95
110
125
145
170
198
230
255
305
d1
PN 160
d2
d3
13,6
17,3
28,5
37,2
42,5
53,9
68,9
80,9
104,3
127,1
154,1
176,1
199,1
248
30
35
50
55
60
75
90
105
125
150
178
210
235
285
50
55
70
75
80
95
110
125
145
170
198
230
255
305
d3
d1
d1
13,6
17,3
27,9
41,1
52,3
66,1
76,3
98,3
119,7
143,3
165,3
187,1
233
PN 250
d2
d3
30
35
50
60
75
90
105
125
160
185
205
230
280
50
55
70
80
95
110
125
145
180
205
225
250
300
d1
12
16,1
26,5
38,3
47,7
60,1
79,6
98,6
120,4
142,8
174,7
194,5
234,5
PN 320
d2
d3
30
35
50
60
80
100
115
135
160
185
230
255
310
50
55
70
80
100
120
135
155
180
205
250
275
330
d1
12
14,9
23,7
35,7
47,5
66,9
76,6
101
128,3
143,7
163,1
184,5
243,9
PN 400
d2
30
35
50
60
90
110
125
145
172
205
230
255
335
d3
d1
d2
d3
50 10
30 50
55 16,9 40 60
70 28,2 50 70
80 40,3 80 100
110 51,1 90 110
130 69,6 120 140
145 79,3 130 150
165 95,3 150 170
192 133,7 188 208
225 149,1 218 238
250
275 193 285 305
355
-
Dimensions in mm
DN
d1
PN 10
d2
d3
d1
PN 16
d2
d3
d1
PN 25
d2
300
350
400
(450)
500
600
700
800
900
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
309,7
314,4
392,2
443
493,8
595,4
695,2
797
894
996
1198
1396
1592
1790
1984
2184
2380
2576
2776
2972
335
385
435
490
540
645
750
840
945
1045
1260
1455
1665
1860
2070
2270
2470
2675
2875
3080
355
405
455
510
560
665
770
860
965
1065
1280
1475
1685
1880
2090
2290
2490
2695
2895
3100
309,7
339,6
390,4
441,2
492
592
693,6
793
894
996
1195
1392
1588
1785
1980
2175
-
335
385
435
490
540
645
750
850
945
1045
1260
1460
1665
1865
2070
2275
-
355
405
455
510
560
665
770
870
965
1065
1280
1480
1685
1885
2090
2295
-
307,9
339,6
388,6
439,6
488
587,6
686,2
784,6
882
988
1188
1385
1585
1780
1975
-
335
385
435
490
540
645
750
855
960
1055
1265
1465
1665
1870
2075
-
355 307,9
405 338,0
455 384,4
510 435,2
560 479,6
665 585
770 683
875 781
980 880
1075 981
1285 1176
1485 1375
1685 1570
1890
2095
-
PN 40
d2
335
385
435
490
540
645
750
855
960
1060
1275
1475
1680
-
d3
d1
PN 63
d2
d3
d1
PN 100
d2
295,5
323,6
371,4
464
560
651
-
335
385
435
560
670
780
-
d3
355
405
455
580
690
800
-
d1
PN 160
d2
279,5
-
335
-
d3
d1
PN 250
d2
355
-
244
-
335
-
d3
355
-
Dimensions in mm
150300
400900
d1
NPS
1
1
1
2
2
3
3
4
5
6
8
10
12
14
16
18
20
22
24
15,7
20,8
26,7
35,1
40,9
52,6
62,7
78,0
90,2
102,4
128,3
154,2
202,7
254,5
304,8
336,6
387,3
438,1
488,9
539,7
590,5
14,0
18,8
24,4
32,5
38,1
49,3
58,9
73,7
85,3
97,3
122,2
146,3
193,8
247,6
298,4
330,2
381,0
431,8
482,6
533,4
584,2
Class
15002500
6,4
11,0
15,2
22,8
27,9
38,2
45,0
58,4
80,1
103,2
124,4
174,6
222,3
273,1
304,8
355,6
406,4
457,2
508,0
558,8
150
3002500
d2
d3
d2
d3
29
33
42
52
60
75
96
105
131
148
160
185
240
295
372
404
461
525
575
632
683
45
53
62
72
80
95
116
125
151
168
180
205
260
315
392
424
481
545
595
652
703
29
33
42
55
64
83
96
118
131
148
177
207
261
315
372
404
461
525
575
632
683
45
53
62
75
84
103
116
138
151
168
197
227
281
335
392
424
481
545
595
652
703
Weld-Ring Gaskets
Dimension Table
Dimensions in mm
NPS
Zoll
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
641,4
692,2
743,0
793,8
844,6
895,4
946,2
997,0
1047,8
1098,6
1149,4
1200,2
1251,0
1301,8
1352,6
1403,4
1454,2
1505,0
d2
695,8
746,6
797,4
848,2
899,0
949,8
1000,6
1051,4
1102,4
1153,0
1203,8
1254,6
1305,4
1356,2
1407,0
1457,8
1508,6
1559,4
d1
715,8
766,6
817,4
868,2
919,0
969,8
1020,6
1071,4
1122,2
1173,0
1223,8
1274,6
1325,4
1376,2
1427,0
1477,8
1528,6
1579,4
635,0
685,8
736,6
787,4
838,2
889,0
939,8
990,6
1041,4
1092,2
1143,0
1193,8
1244,6
1295,4
1346,2
1397,0
1447,8
1498,6
d2
695,8
746,6
797,4
848,2
899,0
949,8
1000,6
1051,4
1102,4
1153,0
1203,8
1254,6
1305,4
1356,2
1407,0
1457,8
1508,6
1559,4
Class 900
d3
715,8
766,6
817,4
868,2
919,0
969,8
1020,6
1071,4
1122,2
1173,0
1223,8
1274,6
1325,4
1376,2
1427,0
1477,8
1528,6
1579,4
d1
d2
d3
622,4
673,2
724,0
774,8
825,6
876,4
927,2
978,0
1028,8
1079,6
1130,4
1181,2
-
708,4
759,2
810,0
860,8
911,6
962,4
1013,0
1064,0
1114,8
1165,6
1216,4
1267,2
-
728,4
779,2
830,0
880,8
931,6
982,4
1033,0
1084,0
1134,8
1185,6
1236,4
1287,2
-
DimensionTable WN 134, PN 10
Dimensions in mm
DN
32 *
40 *
50 *
65 *
80
100 *
125 *
150 *
(175) *
200 *
250
300
350
400
(450)
500
600
700
800
900
1000
d1
37,2
43,1
54,5
70,3
82,5
107,1
131,7
159,3
182,9
207,3
260,4
309,7
341,4
392,2
443,0
493,8
595,4
695,2
797,0
894,0
996,0
d2
d3
d4
groove
d5
65
79
40,0
54
71
85
46,0
60
84
98
59,0
73
101 115
74,6
90
115 135
86,6 102
141 155 111,4 128
166 180 136,4 153
196 210 165,2 183
223 237 189,0 209
246 260 212,0 232
299 315 264,0 285
354 370 314,6 338
390 410 348,6 372
445 465 401,2 427
500 520 453,0 481
555 575 506,0 534
660 680 608,0 638
770 790 710,2 745
875 895 813,0 850
970 990 908,0 945
1075 1095 1012,0 1049
width
spiral wound
gasket
width
d6
d7
7,0
7,0
7,0
7,7
7,7
8,3
8,3
8,9
10,0
10,0
10,5
11,7
11,7
12,9
14,0
14,0
15,0
17,4
18,5
18,5
18,5
6,0
41
53
6,0
47
59
6,0
60
72
6,5
76
89
6,5
88 101
7,0 113 127
7,0 138 152
7,5 167 182
8,5 191 208
8,5 214 231
9,0 266 284
10,0 317 337
10,0 351 371
11,0 404 426
12,0 456 480
12,0 509 533
13,0 611 637
15,0 714 744
16,0 817 849
16,0 912 944
16,0 1016 1048
Weld-Ring Gaskets
Dimension Table
DimensionTable WN 134, PN 16
Dimensions in mm
DN
32 *
40 *
50 *
65 *
80
100 *
125 *
150 *
(175) *
200 *
250
300
350
400
500
600
700
800
900
1000
d1
37,2
43,1
54,5
70,3
82,5
107,1
131,7
159,3
182,9
207,3
260,4
309,7
339,6
390,4
492,0
592,4
693,4
793,0
894,0
996,0
d2
d3
d4
groove
d5
65
79
40,0
54
71
85
46,0
60
84
98
59,0
73
101 115
74,6
90
115 135
86,6 102
141 155 111,4 128
166 180 136,4 153
196 210 165,2 183
223 237 189,0 209
246 260 212,0 232
299 315 264,0 285
354 370 314,6 338
390 410 348,6 372
445 465 401,2 427
555 575 506,0 534
660 680 608,0 638
770 790 710,2 745
875 895 813,0 850
970 990 908,0 945
1075 1095 1012,0 1049
width
spiral wound
gasket
width
d6
d7
7,0
7,0
7,0
7,7
7,7
8,3
8,3
8,9
10,0
10,0
10,5
11,7
11,7
12,9
14,0
15,0
17,4
18,5
18,5
18,5
6,0
41
53
6,0
47
59
6,0
60
72
6,5
76
89
6,5
88 101
7,0 113 127
7,0 138 152
7,5 167 182
8,5 191 208
8,5 214 231
9,0 266 284
10,0 317 337
10,0 351 371
11,0 404 426
12,0 509 533
13,0 611 637
15,0 714 744
16,0 817 849
16,0 912 944
16,0 1016 1048
Dimensions in mm
Dimensions in mm
DN
32
40 *
50 *
65 *
80
100 *
125 *
150 *
(175) *
200 *
250
300
350
400
500
600
700
800
900
1000
d1
37,2
43,1
54,5
70,3
82,5
107,1
131,7
159,3
182,5
206,5
258,8
307,9
339,6
388,8
488,0
588,0
686,0
784,6
882,0
981,0
d2
d3
d4
groove
d5
65
79
40,0
54
71
85
46,0
60
84
98
59,0
73
101 115
74,6
90
115 135
86,6 102
141 155 111,4 128
166 180 136,4 153
196 210 165,2 183
225 245 189,0 209
250 270 214,0 234
310 330 269,0 290
360 380 317,6 341
390 410 348,6 372
445 465 399,2 425
555 575 506,0 534
660 680 608,0 638
770 790 710,2 745
875 895 813,0 850
970 990 908,0 945
1075 1095 1012,0 1049
width
spiral wound
gasket
width
d6
d7
7,0
7,0
7,0
7,7
7,7
8,3
8,3
8,3
10,0
10,0
10,5
11,7
11,7
12,9
14,0
15,0
17,4
18,5
18,5
18,5
6,0
41
53
6,0
47
59
6,0
60
72
6,5
76
89
6,5
88 101
7,0 113 127
7,0 138 152
7,5 167 182
8,5 191 208
8,5 216 233
9,0 271 289
10,0 320 340
10,0 351 371
11,0 402 424
12,0 509 533
13,0 611 637
15,0 714 744
16,0 817 849
16,0 912 944
16,0 1016 1048
DN
32
40 *
50 *
65 *
80
100 *
125 *
150 *
(175) *
200 *
250
300
350
400
500
d2
d1
37,2
43,1
54,5
70,3
82,5
107,1
131,7
159,3
182,5
206,5
258,8
307,9
338,0
388,4
479,6
65
71
84
101
115
141
166
196
225
250
310
360
390
440
540
d3
d4
79
85
98
115
135
155
180
210
245
270
330
380
410
460
560
40,0
46,0
59,0
74,6
86,6
111,4
136,4
165,2
189,0
214,0
269,0
317,6
347,6
394,2
491,0
groove
d5
54
60
73
90
102
128
153
183
209
234
290
341
371
420
519
width
spiral wound
gasket
width
d6
d7
7,0
7,0
7,0
7,7
7,7
8,3
8,3
8,9
10,0
10,0
10,5
11,7
11,7
12,9
14,0
6,0
6,0
6,0
6,5
6,5
7,0
7,0
7,5
8,5
8,5
9,0
10,0
10,0
11,0
12,0
Dimensions in mm
Dimensions in mm
DN
25 *
32 *
40 *
50
65
80
100
125
150
(175)
200
250
300
350
400
d1
28,5
37,2
42,5
54,5
69,7
81,7
106,3
130,7
157,1
181,1
204,9
255,4
301,9
330,6
378,0
d2
61
65
76
85
105
120
145
175
200
225
250
305
355
385
435
d3
d4
75
79
90
105
125
140
165
195
220
245
270
325
375
405
455
33,0
40,0
48,0
58,0
74,6
88,6
111,4
139,2
164,0
188,0
212,0
265,0
311,6
341,6
389,2
groove
d5
47
54
62
72
90
104
128
157
183
208
232
286
335
365
415
width
7,0 6,0
7,0 6,0
7,0 6,0
7,0 6,0
7,7 6,5
7,7 6,5
8,3 7,0
8,9 7,5
9,5 8,0
10,0 8,5
10,0 8,5
10,5 9,0
11,7 10,0
11,7 10,0
12,9 11,0
34
41
49
59
76
90
113
141
166
190
214
267
314
344
392
46
53
61
71
89
103
127
156
182
207
231
285
334
364
414
53
59
72
89
101
127
152
182
208
233
289
340
370
419
518
41
47
60
76
88
113
138
167
191
216
271
320
350
397
494
Weld-Ring Gaskets
Dimension Table
DN
25 *
32 *
40 *
50
65
80
100
125
150
(175)
200
250
300
350
d1
28,5
37,2
42,5
53,9
68,9
80,9
104,3
127,1
154,1
176,1
199,1
248,0
295,5
323,6
d2
61
65
76
85
105
120
145
170
200
225
245
295
350
385
d3
d4
75
79
90
105
125
140
165
190
220
245
265
315
370
405
33,0
40,0
48,0
58,0
74,6
87,6
111,4
135,2
164,0
186,0
207,0
256,0
306,6
337,6
groove
d5
47
54
62
72
90
103
128
153
183
206
227
277
330
361
width
spiral wound
gasket
width
d6
d7
7,0 6,0
7,0 6,0
7,0 6,0
7,0 6,0
7,7 6,5
7,7 6,5
8,3 7,0
8,9 7,5
9,5 8,0
10,0 8,5
10,0 8,5
10,5 9,0
11,7 10,0
11,7 10,0
34
41
49
59
76
89
113
137
166
188
209
258
309
340
46
53
61
71
89
102
127
152
182
205
226
276
329
360
Dimensions in mm
Dimensions in mm
DN
25
40*
50
65
80
100
125
150
(175)
200
250
300
d1
27,9
41,1
52,3
66,1
76,3
98,3
119,7
143,3
165,3
187,1
233,0
279,5
d2
61
76
90
105
115
140
160
190
215
230
280
335
d3
d4
75
90
110
125
135
160
180
210
235
250
300
355
33,0
48,0
59,0
72,6
83,6
106,4
126,2
152,0
175,0
194,0
241,0
290,6
groove
d5
47
62
73
88
99
123
144
171
195
214
262
314
width
spiral wound
gasket
width
d6
d7
7,0
7,0
7,0
7,7
7,7
8,3
8,9
9,5
10,0
10,0
10,5
11,7
6,0
6,0
6,0
6,5
6,5
7,0
7,5
8,0
8,5
8,5
9,0
10,0
34
49
60
74
85
108
128
154
177
196
243
293
46
61
72
87
98
122
143
170
194
213
261
313
DN
10*
15*
25
40
50
65
80
100
125
150
(175)
200
250
d1
12,0
14,9
23,7
35,7
47,5
66,9
76,6
101,0
128,3
143,7
163,1
184,5
243,9
d2
46
51
60
75
90
110
125
145
172
205
230
255
335
d3
d4
60
65
80
95
110
130
145
165
192
225
250
275
355
18,0
23,0
30,0
43,0
56,0
75,6
88,6
109,4
136,2
160,0
182,0
205,0
274,0
groove
d5
width
32 7,0
37 7,0
44 7,0
57 7,0
70 7,0
91 7,7
104 7,7
126 8,3
154 8,9
179 9,5
202 10,0
225 10,0
295 10,5
spiral wound
gasket
width
d6
d7
6,0
6,0
6,0
6,0
6,0
6,5
6,5
7,0
7,5
8,0
8,5
8,5
9,0
Dimensions in mm
Dimensions in mm
DN
10*
15*
25*
40
50
65
80
100
125
150
(175)
200
250
d1
12,0
16,1
26,5
38,3
47,7
60,1
79,6
98,6
120,4
142,8
174,7
194,5
234,5
d2
46
51
61
75
85
100
120
140
165
190
230
255
310
d3
d4
60
65
75
95
105
120
140
160
185
210
250
275
330
18,0
23,0
33,0
45,0
54,0
67,6
87,6
106,4
129,2
152,0
198,0
220,0
257,0
groove
d5
width
32 7,0
37 7,0
47 7,0
59 7,0
68 7,0
83 7,7
103 7,7
123 8,3
147 8,9
171 9,5
218 10,0
240 10,0
278 10,5
spiral wound
gasket
width
d6
d7
6,0
6,0
6,0
6,0
6,0
6,5
6,5
7,0
7,5
8,0
8,5
8,5
9,0
19
24
34
46
55
69
89
108
131
154
200
222
259
31
36
46
58
67
82
102
122
146
170
217
239
277
DN
d1
d2
10* 10,0 46
15* 16,9 51
25
28,2 65
40
40,3 80
50
51,1 90
65
69,6 120
80
79,3 130
100
95,3 150
125 133,7 188
150 149,1 218
200 193,0 285
d3
d4
60
65
85
100
110
140
150
170
208
238
305
18,0
23,0
35,0
49,0
59,0
82,6
92,6
109,4
147,2
169,0
224,0
groove
d5
width
32 7,0
37 7,0
49 7,0
63 7,0
73 7,0
98 7,7
108 7,7
126 8,3
165 8,9
188 9,5
244 10,0
19
24
31
44
57
77
90
111
138
162
184
207
276
31
36
43
56
69
90
103
125
153
178
201
224
294
Weld-Ring Gaskets
Dimension Table
spiral wound
gasket
width
d6
d7
6,0
6,0
6,0
6,0
6,0
6,5
6,5
7,0
7,5
8,0
8,5
19
24
36
50
60
84
94
111
149
171
226
31
36
48
62
72
97
107
125
164
187
243
10
Dimensions in mm
Dimensions in mm
DN
2*
2
3*
3
4
5
6
8
10
12
14
16
18
20
22
24
d1
52,6
62,7
78,0
90,2
102,4
128,3
154,2
202,7
254,5
304,8
336,6
387,3
438,1
488,9
539,7
590,5
d2
d3
d4
81
96
111
131
148
160
194
245
300
372
404
461
515
575
625
683
95
116
125
151
168
180
210
265
320
392
424
481
535
595
645
703
56,0
68,0
82,6
97,4
112,4
132,2
160,2
209,0
262,0
321,6
353,6
406,2
458,0
513,0
563,0
617,0
groove
d5
70
82
98
114
129
150
178
229
283
345
377
432
486
541
593
647
width
spiral wound
gasket
width
d6
d7
7,0
7,0
7,7
8,3
8,3
8,9
8,9
10,0
10,5
11,7
11,7
12,9
14,0
14,0
15,0
15,0
6,0
6,0
6,5
7,0
7,0
7,5
7,5
8,5
9,0
10,0
10,0
11,0
12,0
12,0
13,0
13,0
57
69
84
99
114
134
162
211
264
324
356
409
461
516
566
620
69
81
97
113
128
149
177
228
282
344
376
431
485
540
592
646
DN
*
1*
1*
1*
2
2
3
3
4
5
6
8
10
12
14
16
18
20
22
24
d1
20,8
26,7
35,1
40,9
52,6
62,7
78,0
90,2
102,4
128,3
154,2
202,7
254,5
304,8
336,6
387,3
438,1
488,9
539,7
590,5
d2
d3
d4
52
58
68
71
81
96
111
131
148
170
195
260
315
372
404
461
515
575
632
683
62
68
78
85
95
116
125
151
168
190
215
280
335
392
424
481
535
595
652
703
25,0
32,0
42,0
45,0
56,0
68,0
83,6
97,4
112,4
135,2
161,2
217,0
270,0
321,6
353,6
406,2
458,0
513,0
566,6
617,0
groove
d5
39
46
56
59
70
82
99
114
129
153
179
237
291
345
377
432
486
541
596
647
width
spiral wound
gasket
width
d6
d7
7,0
7,0
7,0
7,0
7,0
7,0
7,7
8,3
8,3
8,9
8,9
10,0
10,5
11,7
11,7
12,9
14,0
14,0
15,0
15,0
5,5
5,5
5,5
6,0
6,0
6,0
6,5
7,0
7,0
7,5
7,5
8,5
9,0
10,0
10,0
11,0
12,0
12,0
13,0
13,0
27
34
44
46
57
69
85
99
114
137
163
219
272
324
356
409
461
516
569
620
Dimensions in mm
Dimensions in mm
DN
*
*
1*
1
1*
2
2
3
4
5
6
8
10
12
14
16
18
20
24
d1
15,7
20,8
26,7
35,1
40,9
52,6
62,7
78,0
102,4
128,3
154,2
202,7
254,5
304,8
336,6
387,3
438,1
488,9
590,5
d2
d3
d4
46
52
56
66
76
90
100
120
150
180
210
260
315
372
404
461
515
575
683
56
62
70
80
90
110
120
140
170
200
230
280
335
392
424
481
535
595
703
20,0
25,0
31,0
40,0
48,0
60,0
70,0
86,6
113,4
140,2
168,2
217,0
270,0
321,6
353,6
406,2
458,0
513,0
617,0
groove
d5
34
39
45
54
62
74
84
102
130
158
186
237
291
345
377
432
486
541
647
width
spiral wound
gasket
width
d6
d7
7,0
7,0
7,0
7,0
7,0
7,0
7,0
7,7
8,3
8,9
8,9
10,0
10,5
11,7
11,7
12,9
14,0
14,0
15,0
5,5
5,5
6,0
6,0
6,0
6,0
6,0
6,5
7,0
7,5
7,5
8,5
9,0
10,0
10,0
11,0
12,0
12,0
13,0
22
27
32
41
49
61
71
88
115
142
170
219
272
324
356
409
461
516
620
33
38
44
53
61
73
83
101
129
157
185
236
290
344
376
431
485
540
646
DN
*
*
1*
1
1*
2
2
3
4
5
6
8
10
12
14
16
18
20
24
d1
15,7
20,8
26,7
35,1
40,9
52,6
62,7
78,0
102,4
128,3
154,2
202,7
254,5
304,8
336,6
387,3
438,1
488,9
590,5
d2
d3
d4
46
51
61
70
80
95
105
125
155
185
210
260
315
372
404
461
515
575
683
60
65
75
90
100
115
125
145
175
205
230
280
335
392
424
481
535
595
703
20,0
25,0
33,0
41,0
49,0
62,0
72,0
89,6
115,4
143,2
168,2
217,0
270,0
321,6
353,6
406,2
458,0
513,0
617,0
groove
d5
34
39
47
55
63
76
86
105
132
161
186
237
291
345
377
432
486
541
647
38
45
55
58
69
81
98
113
128
152
178
236
290
344
376
431
485
540
595
646
width
spiral wound
gasket
width
d6
d7
7,0
7,0
7,0
7,0
7,0
7,0
7,0
7,7
8,3
8,9
8,9
10,0
10,5
11,7
11,7
12,9
14,0
14,0
15,0
6,0
6,0
6,0
6,0
6,0
6,0
6,0
6,5
7,0
7,5
7,5
8,5
9,0
10,0
10,0
11,0
12,0
12,0
13,0
21
26
34
42
50
63
73
91
117
145
170
219
272
324
356
409
461
516
620
Weld-Ring Gaskets
Dimension Table
33
38
46
54
62
75
85
104
131
160
185
236
290
344
376
431
485
540
646
11
Weld-Ring Gaskets
At our disposal we have up-todate machines and our experienced specialist employees in
production are the guarantee of
our high quality.
All information and technical descriptions contained in this brochure correspond to our state
of knowledge at the time of the printing. They are intended as information about our products
and their various applications.
Therefore, we will only guarantee certain attributes described in the brochure or the
suitability for actual intended purposes according to a written express warranty in the actual
individual case. Any industrial proprietary rights must be observed. Orders will only be
accepted and completed under our standard terms and conditions, which we will make
available on request.
URL: www.kempchen.de
12