Kwa Operator's Manual - Km4, Sr10, Km4 Ris
Kwa Operator's Manual - Km4, Sr10, Km4 Ris
Kwa Operator's Manual - Km4, Sr10, Km4 Ris
Before operating the Airsoft gun, read this manual in its entirety. Important safety topics and tips are discussed throughout all of the chapters. Its important that the operator know the principles of gun handling safety and operation prior to firing the Airsoft gun.
SAFETY GUIDELINES
Safety Distance
The effective shooting range is approximately 75 feet. BBs fired from this Airsoft gun may travel further than intended. Make certain that you have an adequate backstop.
Eye Protection
Eye protection should be worn at all times when both shooting and maintaining your Airsoft gun. Protect your eyes from BBs under pressure while performing maintenance on your Airsoft gun.
Until you are certain the chamber is empty, treat every gun as if it were loaded. Do not assume the chamber is empty based on your memory or someone elses words. Always remove the magazine and visually check to confirm the chamber is empty.
Ensure the Airsoft gun barrel is free of obstructions before you fire the gun. Even the smallest obstruction such as dirt, dust or a stuck cleaning patch can cause a jam, misfire or malfunction.
Muzzle Control
Always keep the muzzle of the gun pointed in a safe direction. Never point the muzzle at a person or object that you do not intend to shoot.
Keep the guns safety on until your sights are aligned on your target and you are ready to fire.
Keep your finger off the trigger and out of the trigger guard until your sights are aligned on your target and you are ready to fire.
WARNING! Airsoft BBs can be a choking hazard. Keep them away from children.
SAFETY GUIDELINES
Identify Your Target and Backstop
Before you pull the trigger, make certain of your target and what is beyond it. The Airsoft gun should never be fired at surfaces such as rocks, glass, water, or other hard surfaces where BBs are likely to ricochet in unpredictable directions.
!
Failure To Fire
WARNING! Adult supervision is required for any person under the age of 18.
If the Airsoft gun fails to fire, misfires, or malfunctions, do not look into the gun barrel. BBs can become lodged into the chamber, and serious eye injury may occur.
Performing proper maintenance, as outlined in this manual, ensures that your Airsoft gun will be safe to shoot and will perform to its designed specifications for many years. Alterations, modifications or
adjustments may damage your Airsoft gun, make it unsafe to shoot, and will void all warranty claims.
Always store the Airsoft gun in a safe place, and out of the reach of children. Always transport the Airsoft gun in a carrying case. Never display the Airsoft gun in a public place. Keep the safety engaged, and remove the magazine before storing the Airsoft gun. Note: IT Is yoUr rEsPoNsIBIlITy To TAKE EvEry rEAsoNABlE PrEcAUTIoN To ENsUrE ThE sAfE sTorAgE AND TrANsPorTATIoN of yoUr AIrsofT gUN.
Orange Tip
The orange tip on Airsoft guns helps law Enforcement distinguish between the replica guns from their real firearm counterparts. Altering the coloration or markings required by state or Federal law so as to make the product look more like a firearm is dangerous and may be a crime. Operator assumes all risks and responsibility when doing so.
Airsoft guns have been mistaken by Police and Law Enforcement as real firearms. A confrontation with law enforcement while carrying an Airsoft gun can result in serious injury or even death. It is strongly advised to operate the Airsoft gun at a safe and legal location. In the event that you are approached by law Enforcement personnel, you must comply with their instructions immediately to avoid an incident.
Do not handle or operate your Airsoft gun while under the influence of alcohol, medication or drugs. your Airsoft gun is well-engineered and manufactured to the highest standards. It was carefully inspected before it was packaged and shipped from our factory. Its safe use depends on you alone. you are the ultimate safety device. like many other devices, your Airsoft gun is safe unless handled in an irresponsible or uneducated manner.
What is Covered
Except as specified below, this warranty covers all defects in material and workmanship in KWA products occurring during the above warranty periods. The following are not covered by the warranty: (1) Any product which is not imported and distributed in the U.s.A. by KWA PErforMANcE INDUsTrIEs, INc. (2) Any products not purchased in the U.s.A. from an KWA AUThorIZED rEsEllEr (Note: KWA AUTHORIZED RESELLER can be identified by KWA AUTHORIZED RESELLER sticker displayed in the store. If you are uncertain as to whether a dealer is a KWA AUThorIZED rEsEllEr, please contact KWA PErforMANcE INDUsTrIEs, INc. as listed above). (3) Damaged deterioration or malfunction resulting from: a) Accident, act of nature, abuse, misuse, neglect, unauthorized product repair, opening of or modification or failure to follow instructions supplied with the product. b) Repair or attempted repair by anyone not authorized by KWA PErforMANcE INDUsTrIEs, INc. c) removal of the orange safety tip. (4) Use of the product outside the U.s.A. (5) Damaged batteries or improper use of bullets (BBs), or non approved propellants (ie. Propane, red gas, 134aetc.) (6) Use in industrial, commercial, and/or professional applications.
If during the applicable warranty period from the date of the original purchase your KWA product is found to be defective by KWA Performance Industries, Inc., KWA Performance Industries, Inc. will repair, or at its option, replace with new, used, or equivalent model, the defective product without charge for parts or labor.
If your product needs service, it may be taken or shipped to KWA Performance Industries, Inc. The following procedures apply whenever your unit must be transported for warranty service: you must go to help Desk at www.kwausa.com/support to obtain an rMA number. ThE rMA 2
If your product does not require service, but you have questions regarding its operation, please contact our Technical services Department as listed below. ThIs WArrANTy Is EXPrEssly MADE IN lIEU of All oThEr WArrANTIEs, EXPrEssED or IMPlIED, INclUDINg WIThoUT lIMITATIoN, WArrANTIEs of MErchANTABIlITy AND fITNEss for A PArTIcUlAr PUrPosE. oUr lIABIlITy Is lIMITED To ThE rEPAIr or rEPlAcEMENT, AT oUr oPTIoN, of ANy DEfEcTIvE ProDUcT AND shAll IN No EvENT INclUDE INcIDENTAl or coNsEQUENTIAl coMMErcIAl or ProPErTy DAMAgEs of ANy KIND. WE ArE NoT rEsPoNsIBlE for ProDUcTs losT, sTolEN AND/or DAMAgED DUrINg shIPPINg. soME sTATEs Do NoT AlloW lIMITATIoNs oN hoW loNg AND IMPlIED WArrANTy lAsTs AND/or Do NoT AlloW ThE EXclUsIoN of INcIDENTAl or coNsEQUENTIAl DAMAgEs, ThE ABovE lIMITATIoNs AND EXclUsIoNs MAy NoT APPly To yoU. This warranty gives you specific legal rights, but you may also have other rights which vary from state to state. This Warranty may not be altered other than in writing signed by an officer of KWA Performance Industries, Inc. KWA Performance Industries, Inc. 18571 E. gale Ave. city of Industry, cA 91748-1339 626-581-1777 www.kwausa.com
PACKAGE CONTENTS
2 Allen Wrenches (for cap screw removal) 1 sight Adjustment Tool 1 owners Manual
BREAKIN PERIOD
Airsoft guns, like many other products require a break-in period to ensure the optimal
performance. This break-in period allows the spring, piston, gears and other moving parts to be seated and become more consistent in their movements. Every new KM4 Airsoft gun spring is manufactured with more tension than is required, this break-in period will allow the spring to settle and operate at the specified FPS range. The KWA KM4 Airsoft guns break-in period will require a minimum of 2000 rounds. During this break-in period, the Airsoft gun will require more cleaning because it will expel excessive grease from the gearbox. After the break-in period, the gun will operate within factory specification. The accuracy of the brass barrel will also improve as you continue to use the gun. 3
SPECIFICATIONS
KM4 SR10
Overall Length [Retracted] = 84.45 cm (33.25) Overall Length [Extended] = 92.71 cm (36.5) Outer Barrel Length = 420 mm (16.5) Inner Barrel Length = 425 mm Inner Barrel Diameter = 6.05 mm Weight = 2.97 kg (6.55 lbs) Barrel thread = 14 mm Negative Caliber = 6 mm Magazine Capacity = 350 rounds Rate of Fire = 20+ RPS Velocity = 118~125 MPS (390~410 fPs) Energy Output with = 1.49 Joules Power Source = 9.6V NiMh, 7.4V or 11.1v 15c li-Po/li-fe
KM4 RIS
Overall Length [Retracted] = 80.65 cm (31.75) Overall Length [Extended] = 88.9 cm (35) Outer Barrel Length = 381 mm (15) Inner Barrel Length = 395 mm Inner Barrel Diameter = 6.05 mm Weight = 3.18 kg (7.01 lbs) Barrel thread = 14 mm Negative Caliber = 6 mm Magazine Capacity = 350 rounds Rate of Fire = 20+ RPS Velocity = 118~125 MPS (390~410 fPs) Energy Output with = 1.49 Joules Power Source = 9.6V NiMh, 7.4V or 11.1v 15c li-Po/li-fe
Special Features:
KWA 2GX Gearbox KWA 2G High Performance Bucking Free Float Rail Adapter System Machined, extruded aluminum 10 forend tube with four Picatinny rails Full metal alloy receiver Adjustable flip up front and rear sights 6 position collapsible stock with integrated battery compartment Flat top receiver Semi and Full Auto selective fire
Special Features:
KWA 2GX Gearbox KWA 2G High Performance Bucking Full metal alloy flat top receiver Removable carry handle Adjustable front and rear sights 6 position collapsible stock with integrated battery compartment 2 piece Rail Interface System Semi and Full Auto selective fire
*Individual test results may vary depending on brand of BBs, and chronograph used.
Note: Spring tension will unwind as you fire the gun. Continue winding the magazine regularly as necessary to empty the high cap magazine.
Switch the selector to safe Be sure the safety cap is on Keep your finger off the trigger at all times
WARNING: Use only 6mm high grade BBs. Using low grade BBs will damage the Airsoft gun.
2
Magazine Top Plate
3
5
Winding Wheel
In Safe mode the gun will not fire. For safety, you should keep the switch in safe mode at all times when you are not ready to fire.
2. Semi-Auto
In Semi-Auto mode the gun will fire one shot for each time you pull the trigger.
3. Full Auto
In Full Auto mode the gun will fire continuously as long as the trigger is depressed
!
FUSE
WARNING: Do not pull the trigger when switching the fire selector.
To replace the fuse, remove the butt stock cover and replace fuse with up to 20A glass fuse.
Fuse
BATTERY INSTALLATION
!
1.
WARNING: Stock must be fully collapsed before opening the stock cover. Do not remove the stock completely from the gun, doing so will disconnect the terminal inside
Set fire selector to safe mode. Slightly pull the stock cover release tabs to remove the cover.
2a. Two types of battery can be used, nunchuck battery and small lipo pack battery. When using a nunchuck battery, place the battery into the stock. Push the connector plugs together firmly until they click into place. 2b. When using a small lipo pack battery, place the battery into the stock cover. Push the connector plugs together firmly until they click into place. *Make sure the small lipo pack battery size is no larger than 4h x 1.25W x 0.62D 3. close the butt stock cover.
Stock Cover
2a
Connector Plug
Nunchuck Battery
2b
Connector Plug
HOPUP SYSTEM
The hop-Up device is one of KWAs standard features, giving Airsoft BBs greater stability, further travel and increased accuracy. Airsoft BBs are light-weight and can be affected by wind when fired. With the Hop-Up system, the trajectory of the Airsoft BBs can be adjusted according to the shooting environment or surroundings.
HOP-UP ADJUSTMENT
Pull the charging handle to the rear to open ejection port and reveal Hop-Up adjustment dial. Pull and hold the charging handle to the rear when adjusting hop-Up. Turn the Hop-Up adjustment dial forward to increase hop-up. Turn the Hop-Up adjustment dial backward to decrease hop-up. Excessively turning of the Hop-Up adjustment dial forward can cause Airsoft BBs to jam. Continued firing with a jammed barrel will cause damage to the gearbox. When jamming occurs, immediately stop shooting and turn the Hop-Up adjustment dial backward to decrease hop. remove the jammed Airsoft BBs.
Before removing the jammed Airsoft BBs, be sure to return the hop-up adjustment dial to normal position. After removal of Airsoft BBs, test fire 2 3 rounds to check for clearance. resume adjustment. KWA Airsoft guns are made with precision barrel, use only new, quality Airsoft BBs. The use of recycled or low quality Airsoft BBs are the primary cause of jamming. In most cases, it can severely damage the gearbox and inner barrel.
Excessive Hop Airsoft BB travels an upward trajectory path. Turn the Hop-Up adjustment dial backward to decrease hop-up. Perfect Hop Airsoft BB travels long distance horizontally. Inefficient Hop Airsoft BB travels a downward trajectory path. Turn the Hop-Up
adjustment dial forward to increase hop.
DECREASE HOP-UP
INCREASE HOP-UP
WARNING! If turned too far, the front sight will come off.
Flip the rear sight between general and precise aiming To adjust the horizontal point of impact, rotate the windage knob located on the rear of the sight To adjust the vertical point of impact, rotate the sight elevation knob located on the right side of the sight
Rear Sight
Small Hole
Use this position for precision firing
UP
Turn Clockwise
DOWN
Windage Knob
Large Hole
Use this position for full auto firing
Adjustment Knob
DISASSEMBLY
Note: Before opening the receiver, the piston must be in the forward position.
WARNING: Before removing any parts, be sure the fire selector is set to safe. Always place safety cap on the barrel tip when servicing the gun.
1. fire in semi-automatic mode 2-3 times to clear the barrel and reset the piston. 2. remove the rear Pin only from lower receiver with the provided Allen wrenches. 3. Use one wrench to hold the cap screw and one to turn the set pin. 4. After removal of the cap screw, use the allen wrench to push the pin out. 5. Pull the Upper receiver up. 6. slide out the inner barrel with hop-Up assembly.
2
Cap Screw
4
Retaining Pin
!
ASSEMBLY
1. Insert the inner barrel and hop-Up assembly into the upper receiver 2. secure the hop-Up assembly into the upper receiver. Push down the upper receiver to close 3. Align the pin holes. Insert the Pin and use the allen wrench to tighten the cap screw
10
WARNING! Unload and clear the Airsoft gun of all BBs before cleaning.
Cleaning procedure
The Airsoft gun barrel should be cleaned and lubricated after each shooting session. regular cleaning prevents the effects of BB residue buildup, and ensures all parts are cleaned properly. 1. 2. 3. 4. 5. Ensure that the safety is engaged Disable hop-Up by dialing to the normal position remove the magazine and clear the chamber of loaded BBs Disassemble the receiver (see Disassembly section) steps to use cleaning rod: a. cut a piece of clean cotton cloth to 1 inch by 0.5 inch size. Insert one end of the cloth into the hole in the cleaning rod (adjust the length of cloth for smooth entry into the barrel) b. Wind the cloth around the cleaning rod c. Insert the cleaning rod into the inner barrel, turning the rod as you insert into the barrel d. remove the cleaning rod and check the cotton cloth for dirt. repeat steps a. through c. when necessary cleaning rod cotton cloth 6. clean the remainder of the Airsoft gun with cotton-tipped swabs, or general purpose cleaning cloths.
OPERATING UNDER UNUSUAL CONDITIONS Unusual conditions are defined as any condition requiring special maintenance. Perform maintenance outlined for the climate similar to your operational area Extreme Cold: operating an Airsoft gas gun in extremely cold temperatures is not recommended. cold temperature will cause the hop-Up Bucking to harden, reducing its effectiveness or cause the gearbox shell to fracture during operation, rendering the gun inoperable. Extreme Heat: Do not keep Airsoft gun and batteries under direct sunlight for long periods of time. Dust or Sand: Dust or sand can get into a gun and cause malfunctions and/or excessive wear. Keep the gun covered whenever possible. Use lubricant sparingly, as lube naturally attracts dirt and other particles. After use in a dusty area, always field strip the gun (refer to Disassembly Section) and clean any areas you can reach with a soft, lint-free cloth. Heavy Rain: Keep the gun out of the rain and water. This will prevent electrical failure and fluid build-up inside the mechbox. Dry completely with clean cloth and clean inner barrel if necessary.
11
SOLUTIONS
Motor is running but not firing Motor or Battery is hot after short use
Semi-Auto feature not functioning properly Semi-Auto feature not functioning at all Firing cycle slows down High pitch or grinding noise BB travels upward BB travels downward BB double feeding or rolling out of the barrel
Incorrect timing Internal failure Weak battery Gear may be damaged or Motor level not adjusted Excessive hop Insufficient hop Excessive oil in chamber Hop-Up unit is contaminated Hop-Up unit may be damaged
Set selector to full-auto mode. Dry fire 10-20 rounds before returning it to semi-auto mode Return gun for professional care Recharge battery Return gun for professional care Turn hop adjustment dial backward Turn hop adjustment dial forward Fire 200 rounds to eliminate excessive oil Clean Hop-Up unit with supplied cleaning rod Return gun for professional care Return gun for professional care Use KWA Perfect BBs or other high quality BBs Clean inner barrel with supplied cleaning rod Return gun for professional care Wind wheel underneath magazine Shake or tap magazine to unclog the BBs Return gun for professional care
Damaged adjustment dial or internal parts Use of recycled or low quality BBs Inner barrel is contaminated Inner barrel is damaged
Magazine has not been wound BBs are lodged inside the magazine Internal failure
M42
M121 M116
M125 M101 M125 M97 M125 M125 M23 M35 M39 M40 M127-1 M127 M127-1
12
546
554
534
554
553
537 541
242 126 128 19 176 193 175 265A 266 35A 127 203 101 36A 69 68
553 553
553 541
538 539
2 161A 1A
204 229 47
13
48
164
37 198
138
120 46 173 67
205
17
121
137 153
292
66 123
138
77
182
24
185
209
236 85
261
135
218
174
507 509
508
519
196
500 503 514 520 510 511 517 515 501 516 514 518
14
Parts #
199-1002-138 199-1002-153 199-1002-158 199-1002-159
Description
Parts #
Description
15
Receiver Pin Screws X 2 Rear Sight Clamp Hop-Up Cylinder Hop-Up Bucking Forward Assist Button 199-1002-161A Spring 199-1002-162 Chamber Block Spring 199-1002-163 Charging Handle Spring Charging Handle Latch 199-1002-164 Spring 199-1002-165 Flash Hider Spring 199-1002-171 Hop-Up Bar Spring 199-1002-173 Magazine Catch Spring 199-1002-174 Motor Tension Spring 199-1002-175 Ejection Port Cover Spring Ejection Port Cover Lock 199-1002-176 Spring 199-1002-177 Front Sight Spring 199-1002-182 Selector Spring 199-1002-185 Trigger Guard Lock Spring 199-1002-193 Ejection Port Cover Screw 199-1002-200 Front Sight Base 199-1002-201 Elevation Cover Screw 199-1002-202 Sight Knob Spacers X 2 199-1002-203 Screw M2X5 X 4 199-1002-204 Bolt Plate Carrier Screw 199-1002-205 Magazine Catch Screw Motor Plate Screws X 2 199-1002-206 Metric 199-1002-207 Front Sight Clamp 199-1002-209 Selector Screw 199-1002-210 BB Ramp Screws X 2 Front Sight Base Insert 199-1002-211 Screw 199-1002-215 Windage Knob Set Screw 199-1002-218 Screw MX3 SC X 2 199-1002-226 Hop-Up Wheel Screw 199-1002-227 Grip Screws X 2 Charging Handle Latch 199-1002-229 Pins X 2 199-1002-231 Gas Tube Pin 199-1002-234 Forward Assist Button Pin 199-1002-236 SP 3X20 Roll Pins X 3 199-1002-241 Flash Hider Set Screw 199-1002-242 Pin Retaining Ring 199-1002-243 Hop-Up Spindle Rings X 2 199-1002-252 Gear Box 199-1002-253 Motor 199-1002-259 Rear Sight 199-1002-260 Windage Knob 199-1002-261 Elevation Dial Base 199-1002-262 Elevation Dial
199-1002-265A Barrel Assembly Block 199-1002-266 Top Rail Elevation Dial Plunger 199-1002-273 Cover 199-1002-274 Rear Sight Housing Base 199-1002-282 Rear Sight Plate Spring 199-1002-290 Rear Sight Locking Knob 199-1002-291 Windage Knob Plunger 199-1002-292 Rear Sight Windage Screw 199-1002-293 Elevation Bar 199-1002-294 Elevation Dial Plunger 199-1002-295 Rear Sight Base Screw 199-1002-296 Elevation Knob Pin Rear Sight Elevation 199-1002-301 Spring 199-1002-302 Windage Knob Spring 199-1002-500 Crane Stock 199-1002-501 Butt Plate 199-1002-503 Stock Lever Spacer 199-1002-505 Crane Stock Cover (Left) 199-1002-506 Crane Stock Cover (Right) 199-1002-507 Sling Swivel 199-1002-508 Buffer Tube Retainer 199-1002-509 Stock Buffer Tube 199-1002-510 Stock Lever 199-1002-511 Stock Lever Nut 199-1002-512 Stock Lever Bolt 199-1002-513 Stock Lever Spring 199-1002-514 Fuse Terminals 199-1002-515 Fuse Terminal Screws X 2 199-1002-516 Crane Wire Harness Screw 199-1002-517 Stock Lever Nut Screw 199-1002-518 Fuse 199-1002-519 Crane Wire Harness 199-1002-520 Crane Wire Harness Clamp 199-1002-534 Hand Guard 199-1002-537 Hand Guard Base 199-1002-538 Outer Barrel Nut 199-1002-539 Knurled Hand Guard Ring 199-1002-540 Gas Tube Base Hand Guard Alignment 199-1002-541 Pins X 2 199-1002-546 Outer Barrel 199-1002-548 Gas Tube Base Pins X 2 199-1002-551 Gas Tube Hand Guard Base Screws 199-1001-553 X8 199-1002-554 Barrel Base Pins X 2
276
284
550
182A
260 215
290 272
16 171 162 159 243 2 5 125 158 14 15 243
92B
261
201
16
276
284
550
182A
260 215
290 272
16 171 162 159 243 125 2 5 158 14 15 243
92B
261
201
17
Description
Forward Assist Button Inner Barrel Retainer BB Ramp Chamber Block Detente Bolt Plate Carrier Selector Cover Grip Hop-Up Adjustment Wheel Hop-Up Spindle (Small) Hop-Up Spindle (Large) Hop-Up Bar Lower Receiver Ejection Port Cover Lock Plunger Selector Plate Charging Handle Spring Hook Upper Receiver (Left) Upper Receiver (Right) Bolt Catch Charging Handle Charging Handle Latch Flash Hider Motor Cover Plate Magazine Catch Magazine Catch Button Ejection Port Cover Ejection Port Cover Lock Selector Trigger Guard Rail Retaining Block Swivel Front Top Hand Guard Bottom Hand Guard Hand Guard Clamp Hand Guard Heat Shield Bolt Plate Dust Cover Retainer Set Screw Plate Flash Hider Washer Motor Adjustment Screw Take Down Pin (Front) Take Down Pin (Rear) Gear Box Set Pin Hop-Up Bar Pin Inner Barrel Top Rail Pin Ejection Port Cover Pin Trigger Guard Lock Pin Receiver Pin Screws X 2
Parts #
199-1002-158 199-1002-159 199-1002-161A 199-1002-162 199-1002-163 199-1002-164 199-1002-165A 199-1002-165 199-1002-171 199-1002-173 199-1002-174 199-1002-175 199-1002-176 199-1002-182 199-1002-182A 199-1002-185 199-1002-193 199-1002-199 199-1002-201 199-1002-202 199-1002-203 199-1002-204 199-1002-205 199-1002-206 199-1002-209 199-1002-210 199-1002-215 199-1002-218 199-1002-226 199-1002-227 199-1002-229 199-1002-231 199-1002-234A 199-1002-236 199-1002-239 199-1002-241 199-1002-242 199-1002-243 199-1002-244 199-1002-252 199-1002-253 199-1002-259 199-1002-260 199-1002-261 199-1002-262 199-1002-265A
Description
Hop-Up Cylinder Hop-Up Bucking Forward Assist Button Spring Chamber Block Spring Charging Handle Spring Charging Handle Latch Spring Hand Guard Heat Shield Screws X 2 Flash Hider Spring Hop-Up Bar Spring Magazine Catch Spring Motor Tension Spring Ejection Port Cover Spring Ejection Port Cover Lock Spring Selector Spring Hand Guard Clamp Screw Trigger Guard Lock Spring Ejection Port Cover Screw Hand Guard Clamp Pin Carry Handle Lock Screws X2 Hand Guard Spacer Pins X 2 Screw M2X5 X 2 Bolt Plate Carrier Screw Magazine Catch Screw Motor Plate Screws X 2 Metric Selector Screw BB Ramp Screws X 2 Windage Knob Set Screw Screw M3X8 SC X 2 Hop-Up Wheel Screw Grip Screws X 2 Charging Handle Latch Pins X 2 Gas Tube Pin Forward Assist Button Pin SP 3X20 Roll Pins X 3 Front Swivel Pin Flash Hider Set Screw Pin Retaining Ring Hop-Up Spindle Rings X 2 Locking Clamp Gear Box Motor Rear Sight Windage Knob Elevation Knob Dial Base Elevation Knob Dial Barrel Assembly Block
Parts #
199-1002-266 199-1002-267 199-1002-269 199-1002-271 199-1002-272 199-1002-273 199-1002-274 199-1002-275 199-1002-276 199-1002-277 199-1002-278 199-1002-282 199-1002-283 199-1002-284 199-1002-290 199-1002-291 199-1002-292 199-1002-293 199-1002-294 199-1002-295 199-1002-296 199-1002-297 199-1002-298 199-1002-300 199-1002-301 199-1002-302 199-1002-303 199-1002-304 199-1002-500 199-1002-501 199-1002-503 199-1002-505 199-1002-506 199-1002-507 199-1002-508 199-1002-509 199-1002-510 199-1002-511 199-1002-512 199-1002-513 199-1002-514 199-1002-515 199-1002-516 199-1002-517 199-1002-518 199-1002-519 199-1002-520 199-1002-544 199-1002-550 199-1002-554
Description
Top Rail Hand Guard Ring Barrel Nut Carry Handle Carry Handle Lock Front A Carry Handle Lock Rear B Rear Sight Housing Base Front Sight Front Sight Housing Base Swivel Base Swivel Base Lock Rear Sight Plate Spring Carry Handle Locking Plate Hand Guard End Cap Carry Handle Knobs X 2 Windage Knob Plunger Rear Sight Windage Screw Elevation Bar Rear Sight Elevation Plunger Carry Handle Bolts X 2 Elevation Knob Pin Front Sight Plunger Front Sight Housing Pins X 2 Hand Guard Lock Spring Rear Sight Elevation Spring Windage Knob Spring Front Sight Spring Swivel Mount Spacer Crane Stock Butt Plate Stock Lever Spacer Crane Stock Cover (Left) Crane Stock Cover (Right) Sling Swivel Buffer Tube Retainer Stock Buffer Tube Stock Lever Stock Lever Nut Stock Lever Bolt Stock Lever Spring Fuse Terminals Fuse Terminal Screws X 2 Crane Wire Harness Screw Stock Lever Nut Screw Fuse Crane Wire Harness Crane Wire Harness Clamp Outer Barrel Gas Tube Barrel Base Pins X 2
18
Description
Cylnder Head (Main) Piston (Main) Piston Plate Anti-Reversal Latch (Assembly) Cylinder Anti-Reversal Latch (Assembly) Switch (Assembly) Piston Head Piston (Assembly) Spring Guide (Assembly) Spring Guide (Assembly) Tappet Plate Spring Switch (Assembly) Anti-Reversal Latch Spring Main Spring Tappet Plate Safety Lever Base
Parts #
199-1002-M53 199-1002-M54 199-1002-M55 199-1002-M56 199-1002-M57 199-1002-M58 199-1002-M59 199-1002-M62 199-1002-M63 199-1002-M64 199-1002-M65 199-1002-M69 199-1002-M70 199-1002-M71 199-1002-M72 199-1002-M74 199-1002-M78 199-1002-M79 199-1002-M80
Description
Safety Lever Switch (Assembly) Switch (Assembly) Switch (Assembly) Selector Plate Switch (Assembly) Wire Retainer Gearbox Shell (Left) Gearbox Shell (Right) Disconnect Trigger Switch (Assembly) Switch (Assembly) Switch (Assembly) Selector Plate Contact Air Nozzle Disconnect Spring Safety Lever Spring Trigger Spring
Parts #
199-1002-M96 199-1002-M97 199-1002-M101 199-1002-M107 199-1002-M114 199-1002-M115 199-1002-M116 199-1002-M117 199-1002-M118 199-1002-M119 199-1002-M120
Description
Piston Head Set Screw Bevel Gear Spur Gear Sector Gear Switch (Assembly) Screw X 4 Screw X 2 Screw X 2 Piston (Assembly) Switch (Assembly) Disconnect Screw X 2 Locking Washer (Gearbox) 199-1002-M121 X4 199-1002-M122 Switch (Assembly) 199-1002-M123 Gear Box Set Pin 199-1002-M124 Cylinder O-Ring 199-1002-M125 9mm Bearing X 6 Piston Washer (Assembly) 199-1002-M127 X2 199-1002-M127-1 Grooved Washer X 4
Parts #
199-1002-MG300 199-1002-MG301 199-1002-MG302 199-1002-MG303 199-1002-MG304 199-1002-MG305 199-1002-MG306 199-1002-MG307 199-1002-MG308 199-1002-MG09 199-1002-MG310
Description
Magazine Case Inner Magazine Housing (Left) Inner Magazine Housing (Right) BB Stop BB Compartment Cover Gear # 1 Gear # 2 Winding Wheel BB Spindle Counter Weight Wheel Half Wheel Counter Weight
Parts #
199-1002-MG314 199-1002-MG316 199-1002-MG317 199-1002-MG319 199-1002-MG320 199-1002-MG321 199-1002-MG323 199-1002-MG324 199-1002-MG325 199-1002-MG-26
Description
Magazine Base Plate Sprocket Shaft Sprocket Wheel Pin BB Stop Spring Coil Spring Counter Weight Spring Half Wheel Retainer Clip Phillip Screws X 5 Magazine Base Plate Screw Base Plate Nut
19