Triple-band Panel R1 B1 Y1

Frequency Rang 790–960 1710–2170 2490–2690

Dual Polarization X X X
HPBW 65° 65° 65°
Adjust. Electr. DT 0°–16° 2°–10° 2°–10°
set by hand or by optional RCU (Remote Control Unit)

XXXPol Panel 790–960/1710–2170/2490–2690 65°/65°/65° 15/17/16.5dBi 0°–16°/2°–10°/2°–10°T

Type No. 80010674
Low band R1, connector 1– 2
790 – 960
Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz
Polarization +45°, –45° +45°, –45° +45°, –45°
Average gain (dBi) 14.5 ... 14.4 ... 14.2 14.6 ... 14.5 ... 14.3 14.8 ... 14.6 ... 14.4
Tilt 0° ... 8° ... 16° 0° ... 8° ... 16° 0° ... 8° ... 16°
Horizontal Pattern:
Half-power beam width 69° 68° 67°
Front-to-back ratio, copolar
(180°±30°) > 25 dB > 25 dB > 25 dB
Cross polar ratio Typically: Typically: Typically:
Maindirection 0° > 25 dB > 25 dB > 23 dB
Sector ±60° > 10 dB > 9 dB > 8 dB
Vertical Pattern:
Half-power beam width 16.5° 16.0° 15°
Electrical tilt 0°–16°, continuously adjustable
Min. sidelobe suppression for 0° ... 8° ... 16° T 0° ... 8° ... 16° T 0° ... 8° ... 16° T
first sidelobe above main beam 16 ... 15 ... 15 dB 16 ... 15 ... 15 dB 15 ... 15 ... 15 dB
Impedance 50 Ω
VSWR < 1.5
Isolation: Intrasystem > 30 dB
Isolation: Intersystem > 30 dB (790–960 // 1710–2170 // 2490–2690 MHz)
Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier)
Max. effective power per port 300 W (at 50 °C ambient temperature)
Max. effective power port 1–2 600 W (at 50 °C ambient temperature)
Max. effective power for the antenna 900 W (at 50 °C ambient temperature)

790–960 +45°/–45° Polarization

Y1
68°
125°

16.0°

10 10
1x
3
dB
dB

0
0

Horizontal Pattern Vertical Pattern

0°–16° electrical downtilt
Subject to alteration.

B1
R1

Correlation Table
Frequency range Array Connector
936.4871/a

790 – 960 MHz R1 1–2

1710 – 2170 MHz B1 3–4
2490 – 2690 MHz Y1 5–6

All specifications are subject to change without notice. 80010674 Page 1 of 3

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
Triple-band Panel

High bands B1, connector 3– 4 Y1, connector 5–6

1710 – 2170 2490 – 2690
Frequency range 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2490 – 2690 MHz
Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45°
Average gain (dBi) 17.0 ... 17.0 ... 16.6 17.2 ... 17.2 ... 16.8 17.2 ... 17.2 ... 16.7 16.3 ... 16.6 ... 15.8
Tilt 2° ... 5° ... 10° 2° ... 5° ... 10° 2° ... 5° ... 10° 2° ... 5° ... 10°
Horizontal Pattern:
Half-power beam width 63° 63° 65° 65°
Front-to-back ratio, copolar
(180°±30°) > 25 dB > 25 dB > 25 dB > 25 dB
Cross polar ratio Typically: Typically: Typically: Typically:
Maindirection 0° > 18 dB > 21 dB > 23 dB > 23 dB
Sector ±60° > 9 dB > 9 dB > 10 dB > 8 dB
Vertical Pattern:
Half-power beam width 6.2° 5.8° 5.7° 4.8°
Electrical tilt 2°–10°, continuously adjustable 2°–10°, continuously adjustable
Min. sidelobe suppression for 2° ... 5° ... 10° T 2° ... 5° ... 10° T 2° ... 5° ... 10° T 2° ... 5° ... 10° T
first sidelobe above main beam 14 ... 14 ... 15 dB 14 ... 15 ... 16 dB 14 ... 16 ... 17 dB 14 ... 16 ... 17 dB
Impedance 50 Ω 50 Ω
VSWR < 1.5 < 1.5
Isolation: Intrasystem > 28 dB > 30 dB
Isolation: Intersystem > 30 dB (790–960 // 1710–2170 // 2490–2690 MHz)
Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier)
Max. effective power per port 150 W (at 50 °C ambient temperature)
Max. effective power port 3–6 400 W (at 50 °C ambient temperature)
Max. effective power for the antenna 900 W (at 50 °C ambient temperature)

1710–2170 +45°/–45° Polarization 2490–2690 +45°/–45° Polarization

65° 65°
125° 125°

5.8° 4.8°

10 10 10 10

3 3
dB

dB
dB

dB

3 3

0 0
0 0

Horizontal Pattern Vertical Pattern Horizontal Pattern Vertical Pattern

2°– 10° electrical downtilt 2°– 10° electrical downtilt

Mechanical specifications

Input 6 x 7-16 female (long neck)

Connector position Bottom
Adjustment 3 x, Position bottom
Subject to alteration.

mechanism continuously adjustable

Wind load (N) [lbf] Frontal: 700 [157]
(at Rated Wind Lateral: 270 [61]
Speed: 150 km/h) Rearside: 730 [164]
Max. wind velocity (km/h) 200
[mph] [124]
Height/width/depth (mm) 1403 / 300 / 152
[inches] [55.2 / 11.8 / 6.0]
936.4871/a

Category of mounting hardware M (Medium)

Weight (kg) 20 / 22 (clamps incl.)
[lb] [44.1 / 48.5 (clamps incl.)]
Packing size (mm) 1726 x 322 x 190
[inches] [68.0 x 12.7 x 7.5]
Scope of supply Panel and 2 units of clamps
for 42 – 115 mm
[1.7– 4.5 inches] diameter

Page 2 of 3 80010674 All specifications are subject to change without notice.

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 Accessories
General Information

Accessories (order separately if required) 64

[2.5]

[0.4]
’9
Remarks Weight approx. Units per
Type No. Description
(mm) [inches] (kg) [lb] antenna

85010002 1 clamp Mast diameter: 110 – 220 [4.3 – 8.7] 2.7 [6.0] 2
85010003 1 clamp Mast diameter: 210 – 380 [8.3 – 15.0] 4.8 [10.6] 2
85010013 1 downtilt kit Downtilt angle: 0° – 16° 3.7 [7.4] 1
Accessories (included in the scope of supply)
738546 1 clamp Mast diameter: 42 – 115 [1.7 – 4.5] 1.1 [2.4] 2
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.

1403 [55.2]
1433 [56.4]
1473 [58.0]
Wall mounting: No additional mounting kit needed.

Material: Reflector screen: Aluminum.

Fiberglass housing: It covers totally the internal antenna components.
The special design reduces the sealing areas to a minimum and
guarantees the best weather protection. Fiberglass material guarantees
optimum performance with regards to stability, stiffness, UV resistance
and painting. The color of the radome is light grey.
All nuts and bolts: Stainless steel or hot-dip galvanized steel.

Grounding: The metal parts of the antenna including the mounting kit and the inner
conductors are DC grounded.

Adjustment mechanism
with integrated scale

Dimensions in
mm and [inches]

Layout of interface: 65.5 [2.6]

790-960 t 1710-2170 t 2490-2690

Tilt Til Til
* 152 [6.0]

* 173 [6.8]

B1 B1
108 [4.3]

4 3
84 [3.3]

R1 Y1
R1 Y1
46 [1.8]

49 [1.9]

2 1 6 5
Subject to alteration.

48 [1.9]

101 [4.0]

221 [8.7]
936.4871/a

244 [9.6] Bottom view

* Dimensions refer to radome
* 300 [11.8] Dimensions in mm and [inches]

Any previous data sheet issues have now become invalid.

All specifications are subject to change without notice. 80010674 Page 3 of 3
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 General Information
about Panel Antennas

Environmental Kathrein cellular antennas are designed to operate under the environmental conditions
conditions: as described in ETS 300 019-1-4 class 4.1 E.
The antennas exceed this standard with regard to the following items:
– Low temperature: –55 °C
– High temperature (dry): +60 °C
For antennas equipped with FlexRET: The electrical downtilt adjusting is designed to
operate under the environmental conditions as described in the valid data sheet of the
FlexRET.

Ice protection: Due to the very sturdy antenna construction and the protection of
the radiating system by the radome, the antenna remains operational even under icy
conditions.

Environmental Kathrein antennas fulfil the stated specifications after completion of the environmental
tests: tests as defined in ETS 300 019-2-4. The homogenous design of Kathrein’s antenna
families uses identical modules and materials.
Extensive tests have been performed on typical samples and modules. The vibration
test has been adapted relating to frequency and acceleration to the conditions of mast
mounted antennas.

Please note: As a result of more stringent legal regulations and judgements regarding product
liability, we are obliged to point out certain risks that may arise when products are
used under extraordinary operating conditions.

The mechanical design is based on the environmental conditions as stipulated in

ETS 300 019-1-4. Wind loads are calculated according to DIN 1055-4.
The antennas may be used at locations where the anticipated peak wind velocity or
gust wind speed lies within the maximum wind speed listed in the data sheet. We
warrant the mechanical safety and electrical functionality under such conditions.
The wind speeds are defined in accordance with the DIN, EN or TIA standards. This
warranty makes allowance for the partial safety factors specified in those standards.
Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress
(e.g. strain caused by oscillating support structures), may result in the breakage of an
antenna or even cause it to fall to the ground. These facts must be considered during
the site planning process.

The details given in our data sheets have to be followed carefully when installing
the antennas and accessories.
Site planning and installation must be carried out by qualified and experienced
staff. All relevant national safety regulations must be upheld and respected.
Incorrect site planning, faulty installation, as well as interfering surroundings
on site, may lead to deviations in the electrical parameters compared to those
specified in the respective data sheets.
The connectors on this product are only suitable for connecting to the compatible
counterpart. Please ensure that the connected cable has been fitted with a
Subject to alteration.

connector of the same standard, otherwise damage may occur.

Our quality assurance system and our Our products are compliant to the
environmental management system apply EU Directive RoHS as well as to other
to the entire company and are certified RoHS environmentally relevant regulations
936.4694/b

by TÜV according to EN ISO 9001 and (e.g. REACH).

EN ISO 14001.

Any previous data sheet issues have now become invalid.

All specifications are subject to change without notice. Page 1 of 1
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 Mounting Hardware
Clamp Included in the Scope of Supply

Suitable for mast diameter (mm) 42 – 115

[inches] [1.65 – 4.53]
Antenna – mast distance (mm) 20 – 25
[inches] [0.79 – 0.98]
Material of clamp and screws Hot-dip galvanized steel / stainless steel
Weight (kg) 1.1
[lb] [2.43]

152 [5.98]

100 [3.94]

[0.79–0.98]
40 [1.57]
72 [2.83]

20–25
40 [1.57]

15
2–1
’ 4 4.53]
5–
[1.6

M10 ‰MA = 25 Nm

M8 ‰MA = 20 Nm
35 [1.38]
64 [2.52]
125 [4.92]

20–25
[0.79–0.98]
Subject to alteration.
936.3920/c

Please note: Kathrein does not recommend to use counter nuts.

The additional nuts supplied are only meant as spares. All dimensions in mm and [inches]

Any previous data sheet issues have now become invalid.

All specifications are subject to change without notice. 738546 Page 1 of 1
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 General Instructions
for Adjustment Mechanism

Description of the adjustment mechanism (protective cap removed):

1
2

2
➀ Adjustment wheel with twist-lock ➀ Thread for fixing the protective To set the downtilt angle exactly,
function. cap or the RCU (Remote Control you must look horizontally at the
➁ Downtilt spindle with integrated Unit). scale. The lower edge of the gear-
scale. ➁ Gearwheel for RCU power drive. wheel must be used for alignment.

Manual adjustment procedure:

0° – max.°

0° – max.°

Remove the protective cap. Set downtilt angle by rotating the Screw on the protective cap again.
adjustment wheel.

Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

Subject to alteration.
936.4038/a

For a description of RCU installation please refer to the respective data sheet.

All specifications are subject to change without notice. Page 1 of 2

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
General Instructions for Feederline Installation
for Triple- and Quad-band Antennas

Please note: To avoid any damage to the interfaces, please ensure that only suitable tools are used. To
tighten the feederline connector interfaces, we strongly recommend using a special Kathrein installation tool
(as shown below) in combination with a standard torque-wrench.

Description of bottom end cap (exemplary picture):

Adjustment mechanism Ventilation hole

(protective cap removed)

Spindle with tilting scale

7-16 female (long neck) Colour coding:

Correlation of each RF input to:
– the corresponding adjustment
mechanism
There are eight feederline connectors and four adjustment mechanisms – the frequency range
located at the bottom of the antenna. – the polarization

Installation of the feederline connector and RCU (optional):

In order to protect the adjustment mechanism the protective caps have to be attached during
feederline installation!
Kathrein installation set: Type No. 85010077
Set has to be ordered separately!
Set consists of three spanners of 27, 32 and 41 mm width.
1/2ßsquare actuation
according to
DIN 3120 Form C
Subject to alteration.

32 mm

For the feederline installation

carefully put the connector in
place and hand-screw the nut.
m
Use a torque-wrench to finish m
27

installation. 41
mm

936.4038/a

After feederline installation, the

optional remote control units
These tools are suitable for 7-16 connectors with a wrench size of 27 or
(RCU) R1, B1 and Y1 can be
32 mm, and the RCU attachment nut with a wrench size of 41 mm.
mounted if required. For a full
description of RCU installation Tighten nuts within a torque range of 25 – 33 Nm depending on
please refer to the respective connector manufacturers’ specifications, respectively the RCU nut with
data sheet. a torque range of 15 – 18 Nm.

All specifications are subject to change without notice.

Page 2 of 2 The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com