Circuit Symbol T1
Circuit Symbol T1
Circuit Symbol T1
Circuit symbols are used in circuit diagrams, which show how a circuit is connected together. The actual layout of the components is usually quite different from the circuit diagram. To build a circuit you need a different diagram showing the layout of the parts on the printed circuit board. However understanding electronics circuit give you a better understanding of how to find faults in an electronic circuit
Circuit Symbol
Function of Component
To conduct or pass current from one part of a circuit to another. A 'blob' should be drawn where wires are connected (joined), but it is sometimes omitted. Wires connected to another wire should be staggered slightly to form two Tjunctions, as shown. Such help to transmitted current to other paths In diagrams it is often necessary to draw wires crossing even though they are not connected. It is preferred to have the 'hump' symbol as shown because the simple crossing of the wire may be misread as a join where you have forgotten to add a 'blob'!
Wires joined
Cell
Battery
Supplies electrical energy. A battery is more than one cell. The larger terminal is the positive (+). And the small terminal is called the negative (-) +
DC supply
Supplies electrical energy. DC = Direct Current, always flowing in one direction. Supplies electrical energy. AC = Alternating Current, continually changing direction of it currents it is negative and then Positive which alternates again. A safety device, which will 'blow' or melt if the current flowing through it exceeds a specified value. Used as a protection for electrical circuits. Two coils of wire linked by an iron core. Transformers are used to step up (increase) and step down (decrease) AC voltages. Energy is transferred between the coils by the magnetic field in the core. There is no electrical connection between the coils. A connection to earth. For many electronic circuits this is the 0V (zero volts) of the power supply, but for mains electricity and some radio circuits it really means the earth. It is also known as ground.
AC supply
Fuse
Transformer
Earth (Ground)
Circuit Symbol
Function of Component
A transducer, which converts electrical energy to light. This symbol is used for a lamp providing illumination, for example a car headlamp. A transducer, which converts electrical energy to kinetic energy (motion).
Motor
Bell
Buzzer
A transducer, which converts electrical energy to sound. A coil of wire, which creates a magnetic field when current, passes through it. It may have an iron core inside the coil. It can be used as a transducer converting electrical energy to mechanical energy by pulling on something.
Switches Component
Push Switch (push-to-make)
Circuit Symbol
Function of Component
A push switch allows current to flow only when the button is pressed. This is the switch used to operate a doorbell. It is a abbreviated NO for normally open . This type of push switch is normally closed abbreviated NC for normally closed (on), it is open (off) only when the button is pressed. SPST = Single Pole, Single Throw. An on-off switch allows current to flow only when it is in the closed (on) position. SPDT = Single Pole, Double Throw. A 2-way changeover switch directs the flow of current to one of two routes according to its position. Some SPDT switches have a central off position and are described as 'on-off-on'. DPST = Double Pole, Single Throw. A dual on-off switch, which is often used to switch mains electricity because it can isolate both the live and neutral connections. DPDT = Double Pole, Double Throw. This switch can be wired up as a reversing switch for a motor. Some DPDT switches have a central off position.
Push-to-Break Switch
Relay
An electrically operated switch, for example a 9V battery circuit connected to the coil can switch a 230V AC mains circuit.
NO = Normally Open, COM = Common, NC = Normally Closed.
Resistors Component
Resistor
Circuit Symbol
Function of Component
A resistor restricts the flow of current, for example to limit the current passing through an LED. A resistor is used with a capacitor in a timing circuit. This type of variable resistor with 2 contacts (a rheostat) is usually used to control current. Examples include: adjusting lamp brightness, adjusting motor speed, and adjusting the rate of flow of charge into a capacitor in a timing circuit. This type of variable resistor with 3 contacts (a potentiometer) is usually used to control voltage. It can be used like this as a transducer converting position (angle of the control spindle) to an electrical signal.
Capacitor
Capacitor, polarized
Variable Capacitor
Diodes Component
Diode LED
Light Emitting Diode
Circuit Symbol
Function of Component
A device, which only allows current to flow in one direction. A transducer, which converts electrical energy to light. A special diode, which is used to maintain a fixed voltage in a power supply. A light-sensitive diode. Which react when light is shine direct on it may increase or decrease it resistance
Zener Diode
Photodiode
Transistor NPN
Transistor PNP
A transistor amplifies current. It can be used with other components to make an amplifier or switching circuit.
Phototransistor
A light-sensitive transistor.
Circuit Symbol
Function of Component
A transducer, which converts sound to electrical energy.
Earphone
Loudspeaker
Piezo Transducer
A transducer, which converts electrical energy to sound. An amplifier circuit with one input. Really it is a block diagram symbol because it represents a circuit rather than just one component. A device, which is designed to receive or transmit radio signals. It is also known as an antenna.
Amplifier
(general symbol)
Aerial (Antenna)
Circuit Symbol
Function of Component
A voltmeter is used to measure voltage.
The proper name for voltage is 'potential difference', but most people prefer to say voltage!
Amp-meter
An amp-meter is used to measure current. As known as amps An ohmmeter is used to measure resistance. Most Multimeter have an ohmmeter setting.
Ohmmeter
Circuit Symbol
Function of Component
A transducer which converts temperature (heat) to resistance (an electrical property).
Logic Gates Logic gates process signals, which represent true (1, high, +Vs, on) or false (0, low, 0V, off).
Gate Type
Traditional Symbol
IEC Symbol
Function of Gate
A NOT gate can only have one input. The 'o' on the output means 'not'. The output of a NOT gate is the inverse (opposite) of its input, so the output is true when the input is false. A NOT gate is also called an inverter. An AND gate can have two or more inputs. The output of an AND gate is true when all its inputs are true. A NAND gate can have two or more inputs. The 'o' on the output means 'not' showing that it is a Not AND gate. The output of a NAND gate is true unless all its inputs are true. An OR gate can have two or more inputs. The output of an OR gate is true when at least one of its inputs is true. A NOR gate can have two or more inputs. The 'o' on the output means 'not' showing that it is a Not OR gate. The output of a NOR gate is true when none of its inputs are true.
NOT
AND
NAND
OR
NOR
EX-OR
An EX-OR gate can only have two inputs. The output of an EX-OR gate is true when its inputs are different (one true, one false). An EX-NOR gate can only have two inputs. The 'o' on the output means 'not' showing that it is a Not EX-OR gate. The output of an EX-NOR gate is true when its inputs are the same (both true or both false).
EXNOR