HEC Hms Tutor
HEC Hms Tutor
HEC Hms Tutor
Prepared by Venkatesh Merwade School of Civil Engineering, Purdue University vmerwade@purdue.edu April 2007
Introduction
The intent of this exercise is to introduce you to the structure and some of the functions of the HEC-Hydrologic Modeling System (HEC-HMS), by simulating the runoff hydrographs resulting from a design storm on Waller Creek in Austin, Texas. This exercise involves the study of extreme discharges on Waller Creek using rainfall-runoff analysis. The physical parameters describing the watershed were developed previously using a GIS program (PrePro) available at http://ceprofs.tamu.edu/folivera/GISTools/PrePro2002/PrePro2002.htm. A GIS preprocessing tool called HEC-GeoHMS, available from U.S. Army Corps of Engineers can also be used for this task. HEC-GeoHMS is available at: http://www.hec.usace.army.mil/software/hec-geohms/ A tutorial on how to use the newer version of HEC-GeoHMS that works with the latest version of ArcGIS is available at: http://web.ics.purdue.edu/~vmerwade/tutorial.html
Computer Requirements
You must have a computer with the latest windows operating system, and HEC-HMS 3.1.0 installed. HEC 3.1.0 for windows is available for free from the Hydrologic Engineering Center's home page at: http://www.hec.usace.army.mil/software/hec-hms/download.html. A user's manual is also available at this location. (Purdue Students: The program is loaded on computers in ITaPs JNSN B012 lab)
Data Requirements
To run HEC-HMS model, a basin file is needed to specify the physical parameters of the watershed, and a map file to give the outline of the drainage areas and creeks. These files for Waller creek (zipped as waller.zip) can be downloaded from the following link: http://web.ics.purdue.edu/~vmerwade/education/waller.zip
Make a working directory on your computer and download waller.zip, and unzip its contents. .
Getting Started
Start HEC-HMS by clicking on the HEC-HMS icon by going to Start Programs HEC-HMS HEC-HMS 3.1.0 (Purdue students doing this tutorial in an ITap Lab may have to first run the set-up file by going to Start Programs Course Software Engineering HEC-HMS HEC-HMS 3.1.0) After a few seconds, the following should appear:
Henceforth, this window will be referred to as HMS Interface. The HEC-HMS interface consists of a menu bar, tool bar, and four panes. These panes are referred to as the Watershed Explorer, the Component Editor, the Message Log and the Desktop. More description on these panes, menus and tools is provided when they are used later in the exercise.
The first step is to create a new HEC-HMS project by selecting File New in the menu bar. Enter the project name and description as shown below, and specify your working directory (where waller.zip is downloaded).
If you expand Waller_Ck, you will see different hydrologic elements in the basin in the watershed explorer. Before we get into the details of the basin, go ahead and add the basin map which is stored in the Hms.map file. In the HMS interface, select View Background Maps. This will prompt a Background Maps window. In the Background Maps window, click on Add Browse to the Hms.map file in the working folder (make sure you change the Files of type to HMS Map File (*.map) as shown below), and select it.
This will add Hms.map in the Background Maps window. Click OK to add it to the HMS You should then see a schematic of Waller Creek showing the watershed and stream map and an overlay of the hydrologic elements. You will notice that the whole map of the basin does not fit in the Desktop window. You can change the Desktop settings by selecting View Maximum Extents in the Menu bar. Select the display method as Union of All Maps and Elements with an element buffer of 40 % or more as shown below: 4
Now you should see the whole basin in the desktop window. Save the project.
The arrow tool lets you select any hydrologic element in the basin. You can use the to zoom-in to a smaller area in the desktop, and zoom-out tool to zoom-in tool can be used to move the display in the zoom out to see a larger area. The pan tool desktop. Go ahead and experiment with these buttons to understand better how each works. Now lets explore the basin information.
Hydrologic Elements
The Waller_Ck basin contains different hydrologic elements. The following description gives brief information on each symbol that is used to represent individual hydrologic element. Subbasin Used for rainfall-runoff computation on a watershed.
Reach Used to convey (route) streamflow downstream in the basin model. Reservoir Used to model the detention and attenuation of a hydrograph caused by a reservoir or detention pond. Junction Used to combine flows from upstream reaches and sub-basins. Diversion Used to model abstraction of flow from the main channel. Source Used to introduce flow into the basin model (from a stream crossing the boundary of the modeled region). Source has no inflow. Sink Used to represent the outlet of the physical watershed. Sink has no outflow. The model of Waller Creek contains only 4 of these kinds of elements. There are 18 hydrologic elements in the Waller Creek model, made up of 7 subbasins, 5 river reaches, 5 junctions, and 1 sink at the point where Waller Creek flows into the Colorado River. Notice that when a stream flows through a watershed, the additional local runoff from the drainage area around the stream is not accounted for until the downstream end of the reach where its flow is combined at a junction with the flow coming from the upstream reach. The junctions have been located at points where roads cross Waller Creek.
Remember the sub-basin element is used to convert rainfall to runoff. So the information on methods used to compute loss rates, hydrograph transformation and baseflow is required for each sub-basin element. The loss method allows you to choose the process which calculates the rainfall losses absorbed by the ground. Click (do not select any!) on the drop down menu to see your choices. Some options are SCS Curve No. and Green & Ampt. In this model, Initial and Constant has been selected. This loss relationship means that a quantity of rainfall will be absorbed by permeable soil initially, and a constant rate will be absorbed over the time frame of the model. The loss method will convert the rainfall hyetograph to excess rainfall (chapter 5 in the text book). The Transform method allows you to specify how to convert excess rainfall to direct runoff. Again, click on the drop down menu to view your options. You may remember these options from class notes (chapter 7 in the text book). This model employs the SCS technique (dimensionless unit hydrograph in Chapter 7). The modClark model takes gridded rainfall data, subtracts the losses as specified through the Loss Rates, and converts the excess rainfall to a runoff hydrograph using a variation of what is known as the Clark unit hydrograph. There is no baseflow method specified for this model, but you can look at the available options. If we specify baseflow, this baseflow will be added to the resulting direct run-off hydrograph to produce total streamflow hydrograph. Once the loss and transform methods are chosen for the sub-basin, the next step is to specify the parameters for these methods. Select the Loss tab in the component editor to look at the parameters for the loss method.
Each sub-basin requires an initial loss quantity, a constant loss rate, and a percent imperviousness. These values have been selected arbitrarily. If the % impervious value differs from 0, that % of the land area is assumed to have no losses and the loss method is applied only to the remainder of the drainage area Similarly select the Transform tab to look at the parameters for the transform method.
Note that the SCS unit hydrograph method requires only one parameter for each subbasin: lag time between rainfall and runoff in the sub-basin. The parameter that is specified here is tp, and the program will compute Tc (time of concentration) and qp(peak flow) to rescale the SCS dimensionless unit hydrograph (Chapter 7). This is then used to compute the direct runoff hydrograph for this sub-basin. The Options tab is used to enter observed streamflow and stage data which is left blank for this model. After the sub-basin element, lets look at a reach element. Click on reach 10, and look at its parameters in the component editor.
Since the reach element route flows, only one method (routing) is associated with it. Click on the drop-down menu to look at choices available for routing flows. The Muskingum method is specified here, which is the routing technique used for the reaches in this model. Routing is described in chapters 8-10 in the text book. Select the Route tab to look at the parameters for the routing method (Muskingum).
This simulation routes the water through the reaches by the Muskingum method in which K is the travel time of a flood wave passing through the reach, X is a measure of the degree of storage (X = 0 means a level-pool reservoir or maximum storage, X = 0.5 means a pure transmission reach in which there are no storage effects, and X ranges between 0 and 0.5). The reach is divided into a number of subreaches if necessary to keep the computations numerically stable. You can explore the junctions, source and sink elements to see how they are specified.
There are a couple of ways to look at Basin model. If you expand the sub-basin model (by clicking the + sign next to it) in the watershed explorer, you will see the methods specified for the sub-basin, and when you click on the method, you see the parameters in the component editor. Alternatively, you can look at the parameters for all hydrologic elements by selecting Parameters in the menu bar and selecting a method. For example, by selecting Parameters Transform SCS Unit Hydrograph gives a list of lag times for all the sub-basins in the model as shown below:
We will input the rainfall to HMS in English units (inches). To import an existing basin or meteorological model, one can use the menubar by selecting File Import (like you did for the basin model). To create a new model, we use Components menu. To create a new Meteorologic Model, select Components Meteorologic Model Manager. In the Meteorologic model manager, click New and enter the following information:
Click Create and close the Meteorologic model manager. This will add Meteorologic Models folder to the watershed explorer. Expand the Meteorologic Models folder, and select the Met 1 model as shown below:
` Once the Met 1 model is selected in the watershed explorer, its details will appear in the component editor. The description box includes the description you entered earlier when creating the model. By default, the precipitation data type is Specified Hyetograph (which is the most common data type). In this exercise, however, we will use design precipitation data for Travis County. From the drop-down menu for precipitation, choose Frequency Storm, and specify US Customary units as shown below:
10
Similarly select the Basins tab and specify Yes to include sub-basins. Once we specify the precipitation type, the next step is to enter the data. Unlike Basin model, there is no extra tab in the component editor to enter the data after you choose the precipitation type. To enter the data, you need to expand the Met 1 model in the watershed explorer and then choose the precipitation type (Frequency Storm) as shown below:
This will prompt a precipitation tab in the component editor. Fill in the values shown in the Travis County table above for a 10 year storm (10% chance of being equalled or exceeded in any year). The storm is configured by selecting the exceedance probability (10 % or 10 year return period), output type (Annual duration), duration of maximum intensity (5 mins), storm duration (one day), and percentage of storm that occurs before the peak intensity (50 %) as shown below:
11
Save the project. For each project, the HMS creates an output Data Storage System DSS file which stores calculated data from all runs for a given project so that results from a previous run can be directly compared to results from a more current run.
Click Create and close the control specifications manager. This will add a Control Specifications folder in the watershed explorer. To see the control specifications file, expand the folder, and select Control 1
This will prompt the control specifications tab in the component editor. Specify the duration of the simulation in date and time, and also the time interval of the calculations (10 minutes) as shown below:
12
In this case, the duration is arbitrary; long enough to depict the runoff from a 1-day storm, but the 10 minute time interval is part of the Basin file model setup and should remain fixed for this Waller Creek model.
Click Close. You will see a log in the message log as program executes the model. If there are errors in the model, you will see them in red color. For this model, there are no errors. If you want to make runs with alternative model files, you can do so by first creating/importing new model files (basin, Meteorologic and control specifications), creating a new run (say Run 2) by going to Compute Create simulation run and selecting the new files while creating Run 2. Though the model used in this exercise has one dataset each for basin, meteorology and control specifications, HMS is slick in that it allows the user to have multiple data sets available to include conveniently in different runs.
13
In addition to viewing global results, you may also view results for each element within the model. Again there are a couple of options to do this, and each option provides output in different ways. One option is to use the watershed explorer and component editor tab. To view results, you select the Results tab in the watershed explorer, expand the Simulation Runs folder, and expand Run 1. To see results for any element, expand that element as seen below:
To see the outflow from sub-basin 12, you can select outflow and see the outflow hydrograph in the component editor as shown below:
14
Similarly you can look at other graphs in the component editor by selecting the variable in the watershed explorer. You can select a reach element and see the attenuation in the inflow and outflow hydrograph by selecting the combined inflow and outflow option in the watershed explorer. Each element also has a summary option that gives the results from the global summary table (a single row of the table) for that particular element. Another way of looking at results is by using the tools on the tool bar, which show results in a different way than the component editor. However, to use these tools, you need to select the element by using the component tab in the watershed explorer. For example, select Colorado River (Sink) in the watershed explorer, and click on the view graph tool to get the following graph:
15
The dashed line hydrographs are the inflow data from the sub-basins immediately upstream of the Colorado River which is added to the routed flow in the channel to produce the total outflow curve. If you click on a sub-basin (12), you see the rainfall at the top and the runoff at the bottom as shown below:
16
Unlike a single graph in the component editor, you get to see all graphs (input precipitation, outflow hydrograph, baseflow, precipitation losses) in a single window using this option. You can also see the results in tabular form by using the view time in the toolbar. These functions are also accessed through the Results series table tool menu on the menu bar. OK, you are done with learning the basics of HEC-HMS for event based modeling. The following sections are designed to use your skills in doing some hydrologic design analysis and create new model from scratch.
17
18
19