Nothing Special   »   [go: up one dir, main page]
Scribd Logo
Upload

Welcome to Scribd!

  • 1 views

    Tds Kng1030f2 Pa6+Gf30,Fr

    Uploaded by

    Tanveer Nazir

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Tds Kng1030f2 Pa6+Gf30,Fr

    Uploaded by

    Tanveer Nazir
    1 views2 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    1 views2 pages

    Tds Kng1030f2 Pa6+Gf30,Fr

    Uploaded by

    Tanveer Nazir

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Technical Data Sheet

    KNG1030F2

    Discription PA6 Glass fiber 30% reinforced, Flame retardant(Halogen free)


    Characteristics Rigidity, Heat resistance, UL94 V-0
    Application Automotive : BMA(Battery Module Assembly)
    Electric/Electronics : MCCB

    Injection Molding Guide

    Drying

    Dryer Temperature(℃) Time(hr) Moisture

    Dehumidifier 100 3~4 < 0.12%

    Hot air 110 3~4 < 0.12%

    ※ Definitely dehumidifier is superior to color stability

    Processing Temperature(℃)

    60~80 255~260 250~255 245~250 240~245

    Processing Condition

    Parameter Setting

    Injection Speed Medium~High

    Injection Pressure 60~70% (vs. Injection Capacity)

    Back Pressure 10 ~ 20% (vs. Injection pressure)

    Holding Pressure 40 ~ 60% (based on injection pressure value)

    20 ~ 50 RPM (depends on current screw status like


    Screw Speed
    wear, abrasion)

    Injection / Cooling Time 3-5 / 10-20 seconds

    ※ Recommended condition above are subject to change, according to injection type and capacity.

    General Tips BGFecomaterials provides the material in sealed package after drying, it is highly
    recommended to preheat it under recommended moisture limit before injection
    molding, which is an important process for unsealed package, regardless of unsealed
    duration. The material exposed to moisture over recommended limit might cause
    quality concerns such as gas flow mark, silver streak and drooling, making material
    properties significantly dropped in molded part.
    Thus, preheating is always recommended to improve quality of a molded part in
    surface, mold deposit and molding process ability.
    Technical Data Sheet

    KNG1030F2

    Properties Test Method Condition Unit Value

    Physical properties

    Density ISO 1183 1.42

    Water Absorption ISO 62 23°C, Water 24h % 0.9

    Poisson's Ratio ISO 527 - 0.36

    Mold Shrinkage ISO 294 % 0.3-0.9

    Thermal properties

    Melting Point ISO 3146 ℃ 220

    Heat Deflection Temperature ISO 75 0.45MPa ℃ 221

    1.82MPa ℃ 213

    Fammability

    Flammability UL94 V,0.75mm Rating V0

    GWIT IEC 60695-2-13 0.75mm °C 960

    GWFI IEC 60695-2-12 0.75mm °C 775

    Mechanical properties

    Tensile Strength ISO 527 MPa 150

    Tensile Modulus ISO 527 MPa 10,500

    Tensile Elongation ISO 527 % 3

    Flexural Strength ISO 178 MPa 235

    Flexural Modulus ISO 178 MPa 9,500

    IZOD Impact Strength ISO 180/1A Notched 23℃ KJ/m2 10.0

    Notched -30℃ KJ/m2 9.0

    Rockwell Hardness ISO 2039-2 23℃ R-scale 120

    Electrical properties

    Comparative Tracking Index IEC 60112 V 600

    Dielectric Dissipation Factor ASTM D150 1 MHz 31.98

    ※ Disclaimer : the data in table are typical property values measured by standard test, not guarantied as specification limits.

    The information in this document is submitted to customers


    Headquarter Seoul Office
    for the convenience. Therefore, this information does not
    18586 06160 make any guarantees, warranties, and any legally binding. The
    142, Sangduwon-gil, JangAn- 14F, 411, Teheran-ro, suitability of BGFecomaterials’s products is determined by
    myun, Hwasung-si, Gyunggi- Gangnam-gu, Seoul, each user with all responsibility.
    do, Republic of Korea Republic of Korea
    www.bgfecomaterials.com

    You might also like