P4M900T-M - v1.0
P4M900T-M - v1.0
P4M900T-M - v1.0
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp. MMX, Pentium, Pentium-II, Pentium-III, Pentium-4, Celeron are registered trademarks of Intel Corporation. Other product names used in this manual are the properties of their respective owners and are acknowledged.
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the systems manufacturer could void the users authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation
Chapter 5 VIA VT8237 SATA RAID Setup Guide Describes the information about SATA RAID Setup Go to page 47
Preface
iii
TABLE OF CONTENTS
Preface Chapter 1 i 1
Chapter 2
Installing the Motherboard 7 Safety Precautions......................................................................................7 Choosing a Computer Case.......................................................................7 Installing the Motherboard in a Case......................................................7 Checking Jumper Settings.........................................................................8
Setting Jumpers..............................................................................8 Checking Jumper Settings..............................................................9 Jumper Settings..............................................................................9
Installing Hardware...................................................................................13
Installing the Processor...............................................................13 Installing Memory Modules.........................................................15 Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive........17 Installing a Floppy Diskette Drive...............................................19 Installing Add-on Cards..............................................................20 Connecting Optional Devices......................................................22
Chapter 3
27
The Standard Configuration........................................................27 Entering the Setup Utility..............................................................27 Updating the BIOS.......................................................................29
Using BIOS................................................................................................29
Standard CMOS Setup.................................................................30 Advanced Setup............................................................................31 Advanced Chipset Setup ..............................................................34
iv
Integrated Peripherals.................................................................34 Power Management Setup...........................................................35 PCI/PnP Setup.............................................................................37 PC Health Status..........................................................................37 Frequency/Voltage Control..........................................................39 Load Default Settings ..................................................................40 Supervisor Password..................................................................40 User Password............................................................................41 Save & Exit Setup.........................................................................41 Exit Without Saving......................................................................41
Chapter 4
43
Using the Motherboard Software 43 About the Software CD-ROM................................................................43 Auto-installing under Windows 2000/XP.............................................43
Running Setup..............................................................................43
Chapter 5
47
VIA VT8237 SATA RAID Setup Guide 47 VIA RAID Configurations.......................................................................47 Installing RAID Software & Drives.......................................................54 Using VIA RAID Tool.............................................................................54
Multi-Language Translation
Feature Processor
This motherboard uses an LGA775 type of Intel CoreTM 2 Duo/Pentium D/Pentium 4/ Celeron D that carries the following features: Accommodates Intel CoreTM 2 Duo/Pentium D/Pentium 4/Celeron D processors Supports a system bus (FSB) of 1066/800/533 MHz Supports Hyper-Threading technology CPU Hyper-Threading technology enables the operating system into thinking its hooked up to two processors, allowing two threads to be run in parallel, both on separate logical processors within the same physical processor. The P4M900 Northbridge (NB) and VT8237A/VT8237S Southbridge (SB) chipsets are based on an innovative and scalable architecture with proven reliability and performance. Supports 66 MHz, 4x and 8x transfer modes, Ultra V-Link Host P4M900 interface with 1 GB/s total bandwidth (NB) Supports up to two PCI Express ports, configured as one x16 and one x1 PCI Express lanes Integrated Chrome9 HC 3D/2D Graphics & Video Controller Advanced 64-bit DDR2/DDR SDRAM controller ACPI 2.0 and PCI Bus Power Management 1.1 complaint VT8237A/ VT8237S (SB) Supports 16-bit 66 MHz Ultra V-Link Host interface with total bandwidth of 1 GB/s Compliant with PCI 2.3 specification at 33 MHz, supporting up to 6 PCI masters Integrated Serial ATA/ Serial ATA II Host Controllers, supporting data transfer rates up to 1.5/3.0 Gb/s (Serial ATA II with VT8237S only) Integrated Dual channel UltraDMA 133/100/66 Master Mode EIDE Controller USB 2.0 Controller, supporting up to 8 USB 2.0 ports Integrated keyboard Controller with PS2 mouse support
Chipset
Memory
Supports DDR2 667/533/400 DDR2 SDRAM DIMMs Accommodates two DDR2 unbuffered DIMMs Up to 2 GB per DIMM with maximum memory size up to 4 GB
Audio
This motherboard may support the following Audio chipset: 8 Channels of DAC support 16/20/24-bit PCM Format for 7.1 Audio Solution All ADCs support 48K/192kHz Independent Sample Rate Exceeds Microsoft PC2001 Requirements High Quality Differential CD input Three Stereo DACs support 16/20/24-bit PCM format for 5.1 channel audio solution ADCs support 44.1k/48k/96k sample Rate Meet Microsoft WHQL/WLP 3.1x audio requirements Direct Sound 3DTM compatible
Expansion Options
The motherboard comes with the following expansion options: One PCI Express x16 slot for Graphics Interface One PCI Express x1 slot Two 32-bit PCI v2.3 compliant slots Two 40-pin IDE connectors supporting up to 4 IDE devices One floppy disk drive interface Two 7-pin SATA connectors This motherboard supports UltraDMA bus mastering with transfer rates of 133/100/66 MB/s. The motherboard has a full set of I/O ports and connectors: Two PS/2 ports for mouse and keyboard One serial port One parallel port One VGA port One 1394a port(optional) Four USB ports One LAN port (optional) Audio jacks for microphone, line-in and 6/8-channel (optional) line-out
Integrated I/O
BIOS Firmware
This motherboard uses AMI BIOS that enables users to configure system features including the following: Power management Wake-up alarms CPU parameters CPU and memory timing The firmware can also be used to set parameters for different processor clock speeds.
Some hardware specifications and software items are subject to change without prior notice.
Motherboard Components
Memo
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is OPEN. This illustration shows a 3-pin jumper. Pins 1 and 2 are SHORT
SHORT
OPEN
Jumper Settings
Jumper Type Description Setting (default) 1-2: NORMAL CLR_CMOS 3-pin Clear CMOS 2-3: CLEAR Before clearing the CMOS, make sure to turn off the system. OPEN: Flash Write Enable SHORT: Flash Write Disable
1 CLR_CMOS
BIOS_WP
2-pin
BIOS PROTECT
1 BIOS_WP
To avoid the system unstability after clearing CMOS, we recommend users to enter the main BIOS setting page to Load Optimal Defaults and then Save Changes and Exit.
10
With ATX v1.x power supply, users please note that when installing 20-pin power cable, the latche of power cable clings to the left side of the ATX1 connector latch, just as the picture shows.
With ATX v2.x power supply, users please note that when installing 24-pin power cable, the latches of power cable clings to the right side of the ATX1 connector latch. 24-pin power cable
11
1 2 3 4
Sense PWM
Users please note that the fan connector supports the CPU cooling fan of 1.1A~2.2A (26.4W max.) at +12V.
1 2 3 4
1 2 3 4 5 6 7 8 9 10 11 12
13 14 15 16 17 18 19 20 21 22 23 24
12
Pin 1 3 5 7 9
Signal
Function
HD_LED_P Hard disk LED(+) HD_LED_N Hard disk LED(-) RST_SW_N Reset Switch(-) RST_SW_P RSVD Reset Switch(+) Reserved
Pin Signal Function 2 FP PWR/SLP *MSG LED(+) 4 6 8 FP PWR/SLP *MSG LED(-) PWR_SW_P Power Switch(+) PWR_SW_N Power Switch(-) No pin
10 Key
Reset Switch
Supporting the reset function requires connecting pin 5 and 7 to a momentary-contact switch that is normally open. When the switch is closed, the board resets and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momentarycontact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal debounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.
13
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components. On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed. Avoid using cooling fans with sharp edges on the fan casing and the clips. Also, install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.
14
H. Make sure the CPU fan is plugged to the CPU fan connector. Please refer to the CPU cooling fan users manual for more detail installation procedure.
1. To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary. 2. DO NOT remove the CPU cap from the socket before installing a CPU. 3. Return Material Authorization (RMA) requests will be accepted only if the motherboard comes with the cap on the LGA775 socket.
15
You must install at least one module in any of the two slots. Each module can be installed with 2 GB of memory; total support memory capacity is 4 GB. Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.
Installation Procedure
Refer to the following to install the memory modules. 1 2 3 4 5 6 This motherboard supports unbuffered DDR2 SDRAM . Push the latches on each side of the DIMM slot down. Align the memory module with the slot. The DIMM slots are keyed with notches and the DIMMs are keyed with cutouts so that they can only be installed correctly. Check that the cutouts on the DIMM module edge connector match the notches in the DIMM slot. Install the DIMM module into the slot and press it firmly down until it seats correctly. The slot latches are levered upwards and latch on to the edges of the DIMM. Install any remaining DIMM modules.
16
Type
Size
256 MB
Vendor
Hynix NANYA SAMSUNG
Module Name
HYMP532U646-E3 AA NT256T64UH4A0F-5A M378T3253FG0-CCC NT512T64U88A0F-5A CL3
DDR2 400
512 MB
Nanya
A-DATA Elixir
256 MB
M2OHY2F3G3110A1B0Z M2U25664TUH4A0F-37B HYS64T32400HU-3.7-A KVR533D2N4 RML 1040M28D5F-533 AET660UD00-370A98U HYS64T64400HU-3.7-A KVR533D2N4/512 M378T6553BGO-CD5 ELPIDA E5108AB-5C-E KVR533D2N4/1G HYS64T32400HU-3S-A M2OAD5Q3H3163J1C52 CM2X512-5400C4PRO HYS64T64400HU-3S-A KLCC28F-A8MF5 KVR667D2N5/512 NT512T64U88A0BY-3C K4T51083QC 8G-25JK5-EBT 8D23JK-TT
HYS64T128920HU-3S-A
1 GB 256 MB
512 MB KINGMAX
KINGSTON
DDR2 667
KINGSTON
PQI
KVR667D2N5/1G
MEAD-403LA1001-05B1
17
IDE2: Secondary IDE Connector The second drive on this controller must be set to slave mode. The configuration is the same as IDE1.
IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE. Refer to the IDE device users manual. Installing two IDE devices on one cable, ensure that one device is set to MASTER and the other device is set to SLAVE. The documentation of your IDE device explains how to do this.
18
(optional)
(optional)
the illustration below for proper installation: Attach either cable end to the connector on the motherboard. Attach the other cable end to the SATA hard drive. Attach the SATA power cable to the SATA hard drive and connect the other end to the power supply.
19
20
PCIEX16 Slot The PCI Express x16 slot is used to install an external PCI Express graphics card that is fully compliant to the PCI Express Base Specification revision 1.1. PCIEX1 Slot The PCI Express x1 slot is fully compliant to the PCI Express Base Specification revision 1.1. This motherboard is equipped with two standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.3 compliant. Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.
PCI1~2 Slots
21
Follow these instructions to install an add-on card: 1 2 3 Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw.
For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.
22
1 2 3 4 5 6 7 8 9 10
Pin Pin
AUD_MIC_BIAS Microphone Power AUD_VCC Filtered+5V used by Analog Audio Circuits AUD_F_R AUD_RET_ R REVD Key AUD_F_L AUD_RET_ L Signal Name Signal Name PORT 1L PORT 1R PORT 2R SENSE_SEND PORT 2L Right Channel Audio signal to Front Panel Right Channel Audio signal to Rear Panel Reserved No Pin Left Channel Audio signal to Front Panel Left Channel Audio signal to Rear Panel
Pin 2
1 3 5 7 9
4
6
8 10
23
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
Pin
1 2 3 4
1 2 3 4
24
1 3 5 7
2 4 6 -
1 Pin 2 3 4 5
1 3 5 7 9
2 4 6 8 10
1 2 3
25
Use the upper PS/2 port to connect a PS/2 pointing device. Use the lower PS/2 port to connect a PS/2 keyboard.
Parallel Port (LPT1) Use LPT1 to connect printers or other parallel communications devices. Serial Port (COM1) LAN Port (optional) VGA Port 1394a Port (optional) USB Ports Audio Ports Use the COM port to connect serial devices such as mice or fax/modems. Connect an RJ-45 jack to the LAN port to connect your computer to the Network. Connect the monitor cable to the VGA port. Use the 1394a port to connect 1394 devices. Use the USB ports to connect USB devices. Use the audio jacks to connect audio devices. The D port is for stereo line-in signal, while the F port is for microphone in signal. This motherboard supports 8-channel audio devices that correspond to the A, B, C, and E port respectively. In addition, all of the 3 ports, B, C, and E provide users with both right & left channels individually. Users please refer to the following note for specific port function definition. A: Center & Woofer B: Back Surround C: Side Surround D: Line-in E: Front Out F: Mic_in Rear
The above port definition can be changed to audio input or audio output by changing the driver utility setting. This concludes Chapter 2. The next chapter covers the BIOS.
26
27
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options. This chapter provides explanations for Setup Utility options.
Using BIOS
28
Press DEL/F1 to enter SETUP Press the delete key or F1 to access the BIOS Setup Utility.
CMOS Setup Utility -- Copyright (C) 1985-2005, American Megatrends, Inc.
Standard CMOS Setup Advanced Setup Advanced Chipset Setup Integrated Peripherals Power Management Setup PCI / PnP Setup PC Health Status
Frequency/Voltage Control Load Default Settings Supervisor Password User Password Save & Exit Setup Exit Without Saving
Enter : Select
ESC: Exit
Standard CMOS setup for changing time, date, hard disk type, etc. v02.59 (C)Copyright 1985-2005, American Mega trends, Inc.
FUNCTION
Exits the current menu Scrolls through the items on a menu Modifies the selected fields values Displays a screen that describes all key functions Loads an optimized setting for better performance Saves the current configuration and exits setup Exits the current menu
Using BIOS
29
3 4 5
6 7
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>. Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information. Some options (marked with a triangle ) lead to submenus that enable you to change the values for the option. Use the cursor arrow keys to scroll through the items in the submenu. In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a triangle .
Using BIOS
30
Use [ENTER], [TAB] or [SHIFT-TAB] TO select a field. Use [+] or [-] to configure system Time.
Date and Time The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility. Primary/Secondary IDE Master/Slave, S-ATA 1~2 Your computer has two IDE channels and each channel can be installed with one or two devices (Master and Slave). In addition, this motherboard supports two SATA channels and each channel allows one SATA device to be installed. Use these items to configure each device on the IDE channel. IDE BusMaster (Enabled) This item enables or disables the DMA under DOS mode. We recommend you to leave this item at the default value. Floppy A (1.44 MB 3 1/2) This item sets up size and capacity of the floppy diskette drive(s) installed in the system. Press <Esc> to return to the main menu setting page.
Using BIOS
31
Advanced Setup
This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Advanced Setup Thermal Management TM Status Limit CPUID MaxVal Enhanced Halt (C1E) Intel XD Bit Intel EIST Intel Virtualization Technol Quick Power on Self Test Boot Up Numlock Status APIC Mode Ist Boot Device 2nd Boot Device 3rd Boot Device Hard Disk Drives Removable Drives Try Other Boot Device BIOS Protect Enabled TM1/TM2 Disabled Enabled Disabled Automatic Enabled Enabled On Enabled Removable Dev. Hard Drive CD/DVD Press Enter Press Enter Yes Disabled Help Item For the processor its CPUID belows 0F41h. TM2 only can be enable under below setting. 1. Freq. >=3.66Hz FSB800 2. Freq. >=2.8GHz FSB533
Enter : Select
ESC: Exit
Thermal Management (Enabled) This item displays CPUs temperature and enables you to set a safe temperature to Prescott CPU. TM Status (TM1/TM2) This item displays CPU Thermal Monitor status. Limit CPUID MaxVal (Disabled) This item can support Prescott CPUs for old OS. Users please note that under NT 4.0, it must be set Enabled, while under WinXP, it must be set Disabled Enhanced Halt (C1E) (Enabled) This item enables or disables enhanced halt (C1E). Intel XD Bit (Enabled) This item allows users to enable or disable the Intel XD bit. Intel EIST (Automatic) This item allows users to enable or disable the EIST(Enhanced Intel SpeedStep
technology.
Intel Virtulization Technol (Enabled) This item allows users to enable or disable the Intel Virtulization technology. Quick Power On Self Test (Enabled) Enable this item to shorten the power on self testing (POST) and have your system start up faster. You might like to enable this item after you confident that your system hardware is operating smoothly. Boot Up NumLock Status (On) This item determines if the NumLock key is active or inactive at system start-up time.
Using BIOS
32
APIC Mode (Enabled) This item allows you to enable or disable the APIC (Advanced Programmable Interrupt Controller) mode. APIC provides symmetric multi-processing (SMP) for systems, allowing support for up to 60 processors. 1st/2nd/3rd Boot Device (Removable Dev./Hard Drive/CD/DVD) Use these items to determine the device order the computer used to look for an operating system to load at start-up time. The devices showed here will be different depending on the exact devices installed on your motherboard. Hard Disk Drives (Press Enter) Enter this item, the system will show you the removable drives option.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Hard Disk Drives Help item
Enter : Select
ESC: Exit
Press <Esc> to return to the Advanced Setup Page. Removable Drives (Press Enter) Enter this item, the system will show you the removable drives option.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Removable Drives Help item
Enter : Select
ESC: Exit
Using BIOS
33
Try Other Boot Device (Yes) If you enable this item, the system will also search for other boot devices if it fails to find an operating system from the first boot device. BIOS Protect (Disabled) This item enables or disables BIOS protect. Press <Esc> to return to the main menu setting page.
Enter : Select
ESC: Exit
AGP Aperture Size (128MB) This item defines the size of aperture if you use a graphic adapter. DRAM Timing (Auto) This item allows you to enable or disable the DRAM timing defined by the Serial Presence Detect electrical. Users please note that if setting this item to auto, the following two items are not available. VGA Frame Buffer Size (64MB) This item dispalys the current VGA frame buffer size. Press <Esc> to return to the main menu setting page.
Using BIOS
34
Integrated Peripherals
This page sets up some parameters for peripheral devices connected to the system.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Integrated Peripherals OnBoard Floppy Controller Serial Port1 Address Serial Port2 Adress Serial Port2 Mode Parallel Port Address Parallel Port Mode Parallel Port IRQ Parallel ATA IDE Controller OnBoard SATA-IDE * High Definition Audio * Onboard LAN Controller Onboard LAN BOOT ROM OnBoard USB Function USB Function For DOS Enabled 3F8/IRQ4 2F8/IRQ3 Normal 378 Normal IRQ7 Both IDE Auto Enabled Disabled Enabled Enabled Help Item Allow BIOS to Enable or Disable Floppy Controller.
Enter : Select
ESC: Exit
OnBoard Floppy Controller (Enabled) Use this item to enable or disable the onboard floppy disk drive interface. Serial Port1/2 Address (3F8/IRQ4)/(2F8/IRQ3) Use this item to enable or disable the onboard COM1 serial port, and to assign a port address. Serial Port2 Mode (Normal) If Serial Port 2 Address is not disabled, it allows you to set the Serial Port 2 Mode. Parallel Port Address (378) Use this item to enable or disable the onboard Parallel port, and to assign a port address. Parallel Port Mode (Normal) Use this item to select the parallel port mode. You can select Normal (Standard Parallel Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel Port), or BPP (BiDirectional Parallel Port). Parallel Port IRQ (IRQ7) Use this item to assign IRQ to the parallel port. Parallel ATA IDE Controller (Both) Use this item to set the parallel ATA IDE controller. OnBoard SATA-IDE (IDE) Use this item to set the onboard SATA-IDE channel to be disabled, IDE, or RAID.
Using BIOS
35
High Definition Audio (Auto) Use this item to enable or disalbe the High Definition audio device. Onboard LAN Controller (Enabled) This option allows you to enable or disable the onboard LAN controller. Onboard LAN BOOT ROM (Disabled) Use this item to enable or disable the boot function using the LAN boot rom. Onboard USB Function (Enabled) Enable this item if you plan to use the USB ports on this motherboard. USB Function For DOS (Enabled) Enable this item if you plan to use the USB ports on this motherboard in a DOS environment. Press <Esc> to return to the main menu setting page.
ACPI Suspend Type Suspend Time Out Resume on RTC Alarm Resume On Ring Resume On PME# Resume by WOL Resume On PS/2 Mouse Resume by PCI-E PME PWRON After PWR-Fail Soft-Off By Power Button USB Device Wakeup Function Resume from PS2 KB Wake-Up Key < > : Move F1:General Help
S1 Disabled Disabled Disabled Disabled Disabled Disabled Disabled Power Off Instant Off Enabled Disabled Any Key
Enter : Select
ESC: Exit
ACPI Suspend Type (S1) Use this item to define how your system suspends. In the default, S3 (STR), the suspend mode is a suspend to RAM, i.e., the system shuts down with the exception of a refresh current to the system memory. Suspend Time Out (Disabled) This item sets up the timeout for Suspend mode in minutes. If the time selected passes without any system activity, the computer will enter power-saving Suspend mode. Resume on RTC Alarm (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the systems RTC (realtime clock). Use the items below this one to set the date and time of the wake-up alarm. You must use an ATX power supply in order to use this feature.
Using BIOS
36
Resume On Ring (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the Modem. You must use an ATX power supply in order to use this feature. Resume On PME# (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the PCI Modem or PCI LAN card. You must use an ATX power supply in order to use this feature. Use this item to do wake-up action if inserting the PCI card. Resume by WOL (Disabled) This item specifies whether the system will be awakened from power saving modes when activity or input signal of the specified WOL device is detected. Resume On PS/2 Mouse (Disabled) This item enables or disables you to allow mouse activity to awaken the system from power saving mode. Resume by PCI-E PME (Disabled) This item specifies whether the system will be awakened from power saving modes when activity or input signal of the specified WOL device is detected. PWRON After PWR-Fail (Power Off) This item enables your computer to automatically restart or return to its last operating status. Soft-Off By Power Button (Instant Off) If the item is set to Instant-Off, then the power button causes a software power down. If the item is set to Delay 4 Sec. then you have to hold the power button down for four seconds to cause power down. USB Device Wakeup Function (Enabled) This item allows you to enable or disable the USB device Wakeup function. Resume from PS2 KB (Disabled) This item enables or disables you to allow keyboard activity to awaken the system from S3 mode. Wake-Up Key (Any Key) When Keyboard Power On is set to Enable, this item is available and users can enter any key, or hot key on the keyboard or type in the password. Press <Esc> to return to the main menu setting page.
Using BIOS
37
Enter : Select
ESC: Exit
Init Display First (PCI) Use this item to decide which device to be the initial display device. Allocate IRQ to PCI VGA (Yes) If this item is enabled, an IRQ will be assigned to the PCI VGA graphics system. You set this value to No to free up an IRQ.
Help Item
Enter : Select
ESC: Exit
Using BIOS
38
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Smart Fan Function SMART Fan Control SMART Fan start PWM value SMART Fan start TEMP.(oC) DeltaT SMART Fan Slope PWM value CPU FAN Full Limit Temp [Enabled] 28 43 +3 5 PWM value/oC 63oC Help item Options Disabled Enabled
Enter : Select
ESC: Exit
SMART Fan Control (Enabled) This item enables or disables the control of the system fan speed by adjusting the fan parameter. When it is set at certain temperature, the CPU Fan PWM value will change accordingly. Press <Esc> to return to the PC Health Status page. FANs & Voltage Measurements These items display the monitoring of the overall inboard hardware health events, such as system&CPU temperature, CPU & DIMM voltage, CPU & system fan speed,...etc. Shutdown Temp.(Disabled) This item enables users to set the maximum temperature the system can reach before powering down. Warning Temp.(Disabled) This item enables or disables the warning temperature. Press <Esc> to return to the main menu setting page.
Using BIOS
39
Frequency/Voltage Control
This page helps you manually configure the CPU of this motherborad. The system will automatically detect the type of installed CPU and make the appropriate adjustments to these items on this page.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Frequency/Voltage Control Help Item Auto Disabled 266MHz +0.10V Normal Enabled Disabled Options Auto 333MHz 400MHz 533MHz
Manufacturer : Intel Ratio Actual Value : 9 DRAM Frequency CPU Over-clocking Func. CPU Frequency Memory Voltage CPU Voltage Auto Detect DIMM/PCI Clk Spread Spectrum
Enter : Select
ESC: Exit
Manufacturer (Intel) This item indicates the brand of the CPU installed in your system. Ratio Actual Value (9) This item determinese the actual value of ratio. DRAM Frequency (Auto) This item enables users to adjust the DRAM frequency. The default setting is auto and we recommend users leave the setting unchanged. Modify it at will may cause the system to be unstable. CPU Over-clocking Func. (Disabled) This item decides the CPU over-clocking function/frequencyinstalled in your system. If the over-clocking fails, please turn offthe system power. And then, hold the PageUp key (similar to theClear CMOS function) and turn on the power, the BIOS willrecover the safe default. CPU Frequency (266MHz) This item indicates the current CPU frequency. Users can not make any change to this item. Please noted that the frequency will be varied with different CPU. Memory Voltage (+0.10V) This item determines the DDR voltage adjustment. CPU Voltage (Normal) This item determines CPU voltage adjustment. Auto Detect DIMM/PCI Clk (Enabled) When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots. Spread Spectrum (Disabled) If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic interface) generated by the system.
Using BIOS
40
Supervisor Password
This page helps you install or change a password.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Supervisor Password Supervisor Password : Not Installed Change Supervisor Password Press Enter Install or Change the password. Help item
Enter : Select
ESC: Exit
Supervisor Password (Not Installed) This item indicates whether a supervisor password has been set. If the password has benn installed, Installed displays. If not, Not Installed displays. Change Supervisor Password (Press Enter) You can select this option and press <Enter> to access the sub menu. You can use the sub menu to change the supervisor password. Press <Esc> to return to the main menu setting page.
Using BIOS
41
User Password
This page helps you install or change a password.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. User Password User Password : Not Installed Change User Password Press Enter Install or Change the password. Help item
Enter : Select
ESC: Exit
User Password (Not Installed) This item indicates whether a user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays. Change User Password (Press Enter) You can select this option and press <Enter> to access the sub menu. You can use the sub menu to change the user password. Press <Esc> to return to the main menu setting page.
Using BIOS
42
Memo
Using BIOS
43
If the opening screen does not appear; double-click the file setup.exe in the root directory.
44
Setup Tab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install.
Browse CD The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support CD. Before installing the software from Windows Explorer, look for a file named README.TXT, INSTALL.TXT or something similar. This file may contain important information to help you install the software correctly. Some software is installed in separate folders for different operating systems. In install the software, execute a file named SETUP.EXE or INSTALL.EXE by double-clicking the file and then following the instructions on the screen. Exit The EXIT button closes the Auto Setup window.
Application Tab Lists the software utilities that are available on the CD. Read Me Tab Displays the path for all software and drivers available on the CD.
Running Setup
Follow these instructions to install device drivers and software for the motherboard:
1. Click Setup. The installation program begins:
The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing. The motherboard identification is located in the upper left-hand corner.
45
2. Click Next. The following screen appears:
3. 4.
Check the box next to the items you want to install. The default options are recommended. Click Next run the Installation Wizard. An item installation screen appears:
5.
Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation.
46
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard. Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder. If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.
47
Chapter 5 VIA VT8237 SATA RAID Setup Guide VIA RAID Configurations
The motherboard includes a high performance Serial ATA RAID controller integrated in the VIA VT8237 Southbridge chipset. It supports RAID 0, RAID 1 and JBOD with two independent Serial ATA channels. RAID: (Redundant Array of Independent Disk Drives) use jointly several hard drives to increase data transfer rates and data security. It depends on the number of drives present and RAID function you select to fulfill the seurity or performance pruposes or both. RAID 0 (called data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a sustained data transfer rate, double that of a single disk alone, thus improving data access and storage. RAID 1 (called data mirroring) copies and maintains an identical image of data from one drive to a second drive. If one drive fails, the disk array management software directs all applications to the surviving drive as it contains a complete copy of the data in the other drive. This RAID configuration provides data protection and increases fault tolerance to the entire system. JBOD: (Just a Bunch of Drives) Also known as Spanning. Two or more hard drives are required. Several hard disk types configured as a single hard disk. The hard drives are simply hooked up in series. This expands the capacity of your drive and results in a useable total capacity. However, JBOD will not increase any performance or data security.
48
iii 1 2 3 4 5 6 7 Either end of the Serial ATA data cable can be connected to the SATA hard disk or the SATA connector on the motherboard. Install the Serial ATA hard disks into the drive bays. Connect one end of the Serial ATA cable to the motherboards primary Serial ATA connector (SATA1). Connect the other end of Serial ATA cable to the master Serial ATA hard disk. Connect one end of the second Serial ATA cable to the motherboards secondary Serial ATA connector (SATA2). Connect the other end of Serial ATA cable to the secondary Serial ATA hard disk. Connect the Serial ATA power cable to the power connector on each drive. Proceed to section Entering VIA Tech RAID BIOS Utility for the next procedure.
The RAID BIOS information on the setup screen shown is for reference only. What you see on your screen may not by exactly the same as shown.
On the upper-right side of the screen is the message and legend box. The keys on the legend box allow you to navigate through the setup menu options. The message describes the function of each menu item. The following lists the keys found in the legend box with their corresponding functions.
F1 Enter ESC
View Array Move to the next item Confirm the selection Exit
49
Create Array
1 In the VIA RAID BIOS utility main menu, select Create Array then press the <Enter> key. The main menu items on the upper-left corner of the screen are replaced with create array menu options.
3 4
Select RAID 0 for performance from the menu and press <Enter>. From this point, you may choose to auto-configure the RAID array by selecting Auto Setup for Performance or manually configure the RAID array for stripped sets. If you want to manually configure the RAID array continue with next step, otherwise, proceed to step #5. Select Select Disk Drives, then press <Enter>. Use arrow keys to select disk drive/s, then press <Enter> to mark selected drive. An asterisk is placed before the selected drive. Select Block Size, then press <Enter> to set array block size. Lists of valid array block sizes are displayed on a pop-up menu.
Tip
For server systems, it is recommended to use a lower array block size. For multimedia computer systems used mainly for audio and video editing, a higher array block size is recommended for optimum performance.
Use arrow keys to move selection bar on items and press <Enter> to select.
50
5 Select Start Create Process and press <Enter> to setup hard disk for RAID system. The following confirmation appears: The same confirmation message appears when the Auto Setup for Performance option is selected.
Select RAID 1 for data protection from the menu and press <Enter>. Select next task from pop-up menu. The task Create only creates the mirrored set without creating a backup. Create and duplicate creates both mirrored set and backup.
4 5
Select task and press <Enter>. The screen returns to Create Array menu items. From this point, you may choose to auto-configure the RAID array by selecting Auto Setup for Data Security or manually configure the RAID array for mirrored sets. If you want to manually configure the RAID array continue with next step, otherwise, proceed to step #5. Select Select Disk Drives, then press <Enter>. Use arrow keys to select disk drive/s, then press <Enter> to mark selected drive. (An asterisk is placed before a selected drve.) Select Start Create Process and press <Enter> to setup hard disk for RAID system. The following confirmation message appears: The same confirmation message appears when the Auto Setup for Performance option is selected.
51
Delete Array
1 2 In the VIA RAID BIOS utility main menu, select Delete Array then press the <Enter> key. The focus is directed to the list of channel used for IDE RAID arrays. Press the <Enter> key to select a RAID array to delete. The following confirmation message appears.
52
If user selects Continue to boot, it will enable duplicating the array after booting into OS.
53
1. Power off and Check the Failed Drive: This item turns off the computer and replaces the failed hard drive with a good one. If your computer does not support APM, you must turn off your computer manually. After replacing the hard drive, boot into BIOS and select Choose replacement drive and rebuild to rebuild the broken array. 2. Destroy the Mirroring Relationship: This item cancels the data mirroring relationship of the broken array. For broken RAID 1 arrays, the data on the surviving disk will remain after the destroy operation. However, Destroy the Mirroring Relationship is not recommended because the data on the remaining disk will be lost when the hard drive is used to create another RAID 1 array. 3. Choose Replacement Drive and Rebuild: This item enables users to select an already-connected hard drive to rebuild the broken array. After choosing a hard drive, the channel column will be activated.
Highlight the target hard drive and press <Enter>, a warning message will appear. Press Y to use that hard drive to rebuild, or press N to cancel. Please note selecting option Y will destroy all the data on the selected hard drive. 4. Continue to boot: This item enables BIOS to skip the problem and continue booting into OS.
54
5 6
55
The InstallShield Wizard will begin automatically for installation. Click on the Next button to proceed the installation in the welcoming window.
56
Put a check mark in the check box to install the feature you want. Then click Next button to proceed the installation.
After the software is finished installation, it will automatically started every time Windows is initiated. You may double-click on the icon shown in the system tray of the tool bar to launch the VIA RAID Tool utility.
57
The main interface is divided into two windows and the toolbar above contain the main functions. Click on these toolbar buttons to execute their specific functions. The left windowpane displays the controller and disk drives and the right windowpane displays the details of the controller or disk drives. The available features are as following:
View by Controller
View by Devices
Help Topics
It means that VT8237 SATA RAID only has the feature of monitoring the statuses of RAID 0 and RAID 1. Click on or button to determine the viewing type of left windowpane. There are two viewing types: By controllers and by device. Click on the object in the left windowpane to display the status of the object in the right windowpane. The following screen shows the status of Array 0-RAID 0.
58
Click on the plus (+) symbol next to Array 0--RAID 0 to see the details of each disk.
or
59
Click on the plus (+) symbol next to Array 0; RAID 1 to see the details of each disk.
60
Memo
Cette carte mre utilise un type LGA775 de Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D prsentant les fonctionnalits suivantes : Reoit des processeurs Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D Prend en charge un bus systme (FSB) de 1066/800/533 MHz Prend en charge le CPU de technologie " Hyper-Threading" La technologie Hyper-Threading permet au systme dexploitation de penser quil est connect deux processeurs, permettant dexcuter deux threads en parallle, la fois sur des processeurs logiques spars dans le mme processeur physique.
Chipset
Les chipsets P4M900 Northbridge (NB) et VT8237A/VT8237S Southbridge (SB) sont bass sur une architecture novatrice et dimensionnable avec une abilit et des performances prouves Prend en charge les modes de transfert 66 MHz,4X/8X, interface P4M900 dhte Ultra V-Link avec bande passante totale de 1 Go/s (NB)
Deux contrleurs PCI Express spars, congures comme une ligne x16 et une ligne x1 PCI Express Contrleur Graphique et Vido 3D/2D Chrome9 HC intgr Contrleur SDRAM DDR2/DDR 64 bits avancs Conforme ACPI 2.0 et PCI Bus Management 1.1
Prend en charge une interface Hte Ultra V-Link de 66 MHz en 16 bits avec une bande passante totale de 1 Go/s. Conforme aux spcications PCI 2.3 en 33 MHz, supportant jusqu 6 matres PCI Contrleurs dhte Serial ATA/ Serial ATA II intgrs, prenant en charge des vitesses de transfert jusqu 1,5/3,0 Gb/s (Serial ATA II avec VT8237S seulement) Contrleur EIDE de Mode Matre UltraDMA 133/100/66 Canal double intgr Contrleur USB 2.0, supportant 8 ports USB 2.0 Contrleur clavier intgr avec support de souris PS2
Mmoire
Prend en charge les DIMM DDR2 SDRAM DDR2 667/533/400 Reoit deux DDR2 DIMM sans tampon Jusqu 2 Go par DIMM avec une taille de mmoire maximum de 4 Go
Audio
Cette carte mre prend en charge les chipsets Audio suivants : 8 canaux de format PCM 16/20/24-bits de support DAC pour solution audio 7.1 Tous les ADC prennent en charge la vitesse dchantillonnage indpendante 48K/192kHz Dpasse les exigences de Microsoft PC2001 Entre CD diffrentielle de haute qualit Trois DAC stro prenant en charge le format PCM 16/20/24 bits pour solution audio de canal 5.1 ADC prenant en charge la vitesse dchantillonnage de 44,1k/48k/96k Conforme aux exigences audio de Microsoft WHQL/WLP 3.1x Compatible Direct Sound 3DTM
Multi-Language Translation
Franais
Caractristiques Processeur
LAN interne
Franais
Le contrleur LAN interne offre les caractristiques suivantes: Supporte le fonctionnement en Auto-ngociation N-Way et 10 /100 Mb/s Prise en charge de Wake-On-LAN (WOL) et rveil distant. Prend en charge la capacite half/full duplex Supporte le fonctionnement en Auto-ngociation N-Way et 10Mb/s et 100Mb/s Solution couche physique 100Base-TX/10Base-T simple puce. Prend en charge la capacite half/full duplex Emetteur-rcepteur 10/100/1000 intgr Prend en charge PCI v2.3, 32 bits, 33/66-MHz Prise en charge totale avec IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Conforme au contrleur dhte puce simple pour IEEE 1394-1995 et IEEE1394a-2000 PHY 2 ports intgr de 400 Mb/s pour le Bus PCI Alimentation 3,3V avec entres tolrantes de 5V.
Options dextension
La carte mre est livre avec les options dextensions suivantes: Un logement PCI Express x16 pour Interface Graphique Un logement PCI Express x1 Deux logements conforme PCI v2.3 32 bits Deux connecteurs prol bas IDE de 40 broches prenant en charge jusqu quatre priphriques IDE Une interface de lecteur de disquette Deux connecteurs SATA 7 broches Cette carte mre prenant en charge la matrise de bus UltraDMA avec vitesses de transfert de 133/100/66 Mo/s.
E/S intgres
La carte mre possde un jeu complet de ports dE/S et de connecteurs: Deux ports PS/2 pour souris et clavier Un port srie Un port parallle Un port VGA Un port 1394a (optionnel) Quatre ports USB Un port LAN (optionnel) Prises audio pour microphone, ligne dentre et ligne de sortie/sortie 6/8 canaux (en option)
Microprogramme BIOS
La carte mre utilise AMI BIOS qui permet aux utilisateurs de congurer de nombreuses caractristiques du systme comprenant les suivantes: Gestion de lalimentation Alarmes de rveil Paramtres de CPU Synchronisation du CPU et de la mmoire Le microprogramme peut aussi tre utilis pour dnir les paramtres pour les vitesses dhorloges de diffrents processeurs. Certaines spcications matrielles et lments de logiciels peuvent tre modis sans avertissement.
Multi-Language Translation
Feature Prozessor
Dieses Mainboard verwendet einen LGA775 Typ Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D mit den folgenden Eigenschaften: Nimmt Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D Prozessoren auf Untersttzt einen Systembus (FSB) mit 1066/800/533 MHz Untersttzt eine CPU mit Hyper-Threading Technologie Bei der Hyper-Threading Technologie denkt das Betriebssystem, dass es an zwei Prozessoren angeschlossen ist. Dadurch knnen im selben physikalischen Prozessor zwei Threads parallel auf separaten logischen Prozessoren laufen.
Chipsatz
Die Chipstze P4M900 Northbridge (NB) und VT8237A/VT8237S Southbridge (SB) basieren auf einer innovativen und skalierbaren Architektur mit bewiesener Zuverlssigkeit und Leistung. Untersttzt Transfermodi von 66 MHz, 4x/8x, Ultra V-Link P4M900 Host-Interface mit einer Bandbreite von insgesamt 1 GB/s (NB) Untersttzt bis zu zwei PCI Express-Anschlsse, konguriert als ein x16 und ein x1 PCI Express-Lanes Integrierter Chrome9 HC 3D/2D Grak- & Videocontroller Fortschrittlicher 64-Bit DDR2/DDR SDRAM-Controller Entspricht ACPI 2.0 und PCI Bus Management 1.1
Speicher
Untersttzt 16-Bit 66 MHz Ultra V-Link Host-Interface mit einer Bandbreite von insgesamt 1 GB/s Entspricht den Richtlinien der PCI 2.3- spezikationen von 33 MHz, mit einer Untersttzung von bis zu 6 PCI Master Integrierte Serial ATA/ Serial ATA II Host-Controller, untersttzen Datentransferraten von bis zu 1.5/3.0 Gb/s (nur Serial ATA II mit VT8237S) Eingebauter Doppel-Kanal UltraDMA 133/100/66 Master Modus EIDE-Controllerr USB 2.0 Controller, mit einer Untersttzung fr 8 USB 2.0 Steckvorrichtungen Eingebauter Tastatur-Controller mit einer PS2-Maus-Untersttzung
Untersttzt DDR2 667/533/400 DDR2 SDRAM DIMMs Es knnen zwei ungepufferte DDR2-DIMMs aufgenommen werden. Bis zu 2 GB pro DIMM mit maximaler Speicherkapazitt von bis zu 4 GB.
Audio
Dieses Mainboard kann einen der folgenden Audio-Chipstze untersttzen: 8-Kanal DAC Untersttzung 16/20/24-Bit PCM-Format fr 7.1 Audio Alle ADCs untersttzen eine unabhngige Samplingrate von 48K/192kHz bertrifft Microsoft PC2001 Anforderungen Hochwertiger Differential-CD-Eingang Drei Stereo-DACs untersttzen 16/20/24-Bit PCM-Format fr 5.1 KanalAudiolsung ADCs untersttzen eine Samplingrate von 44.1k/48k/96k Entspricht den Anforderungen von Microsoft WHQL/WLP 3.1x Kompatibel mit Direct Sound 3DTM
Multi-Language Translation
Deutsche
Der Onboard-LAN-Kontroller hat folgende Eigenschaften: Untersttzt den Betrieb bei 10/100 Mb/s N-Way Auto-Negotiation Untersttzung fr Wake-on-LAN( WOL) und Remote Wake-up Untersttzt Halb-/Vollduplex Untersttzt den Betrieb bei 10Mb/s und 100Mb/s N-Way Auto-Negotiation Single-Chip 100Base-TX/10Base-T Bitbertragunsschicht-Lsung Untersttzt Halb-/Vollduplex Enthlt 10/100/1000 Transceiver Untersttzung von PCI v2.3, 32-Bit, 33/66-MHz Volle Untersttzung mit IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Integriertes LAN(Optional)
Deutsche
Kompatibel mit Singlechip-Host Controller fr IEEE 1394-1995 und IEEE1394a-2000 Integrierter 400 Mb/Sek 2-Port PHY fr den PCI-Bus 3.3V Stromversorgung mit 5V-toleranten Eingngen
Erweiterungsoptionen
Das Mainboard bietet die folgenden Erweiterungsoptionen: Ein PCI-Express x16 Steckplatz fr eine Grakschnittstelle Ein PCI Express x1 Steckplatz Zwei 32-bit PCI v2.3-Steckpltze Zwei 40-Pin IDE Flachstecker, die bis zu 4 IDE-Gerte untersttzen Ein Steckplatz fr ein Diskettenlaufwerk Zwei 7-Pin SATA-Stecker Dieses Motherboard untersttzt UltraDMA Bus Mastering mit einer bertragungsrate von 133/100/66 MB/Sek.
Integrierte I/O-Schnittstellen
Das Mainboard verfgt ber einen kompletten Satz von I/O-Schnittstellen und Anschlssen: Zwei PS/2-Schnittstellen fr Tastatur und Maus Eine serielle Schnittstelle Eine parallele Schnittstelle Eine VGA-Schnittstelle Eine 1394a-Schnittstelle (optional) Vier USB-Schnittstellen Eine LAN-Schnittstelle (optional) Audiobuchsen fr Mikrofon, Line-in und 6/8-Kanal (optional) Line-out Dieses Mainboard setzt das AMI BIOS ein, mit dem der Anwender viele Systemeigenschaften selbst kongurieren kann, einschlielich der folgenden: Energieverwaltung Wake-up Alarm CPU-Parameter CPU- und Speichertiming Mit der Firmware knnen auch Parameter fr verschiedene Prozessortaktgeschwindigkeiten eingestellt werden. Einige Hardware- und Software-Spezikationen knnen jederzeit und ohne vorherige Ankndigung gendert werden.
BIOS Firmware
Multi-Language Translation
Caratteristiche Processore
Chipset
Il chipset P4M900 Northbridge (NB) e VT8237A/VT8237S Southbridge (SB) basato su un'innovativa architettura scalabile e offre afdabilit e prestazioni comprovate. Supporto di interfaccia per Ultra V-Link a 66 MHz, modalit di P4M900 trasferimento 4X/8X, con larghezza di banda totale di 1 GB/s (NB) Supporto di no a due porte PCI Express, congurate una come corsia PCI Express x16 e una come corsia PCI Express x1 Controller graca 3D/2D e video Chrome9 HC 3D/2D integrato Controller SDRAM DDR2/DDR a 64 bit avanzato Conforme ad ACPI 2.0 e PCI Bus Management 1.1 Supporto di interfaccia per Host Ultra V-Link a 66 MHz a 16 VT8237A bit con larghezza di banda totale di 1 GB/s /VT8237S Conforme alle speciche PCI 2.3 a 33 MHz, in grado di sup(SB) portare no a 6 master PCI. Host controller Serial ATA/Serial ATA II integrati, con supporto di velocit di trasferimento dati no a 1,5/3,0 Gb/s (solo Serial ATA II con VT8237S) Controller Master integrato UltraDMA a due canali 133/100/66 Master Mode EIDE Controller Controller USB 2.0, in grado di supportare sino a 8 porte USB 2.0. Controller integrato per la Tastiera e supporto mouse PS2
Memoria
Supporto di DIMM SDRAM DDR2 DDR2 667/533/400 Alloggia 2 DDR2 DIMM unbuffered Dimensione massima della DIMM pari ad 2 GB per un ammontare massimo di 4 GB di memoria
La scheda madre offre supporto per uno dei seguenti chipset Audio: 8 canali per formato PCM a 16/20/24 bit con supporto DAC per soluzioni audio 7.1 Tutti i convertitori ADC supportano una velocit di campionamento indipendente di 48 K/192 kHz Superiore ai requisiti Microsoft PC2001 Ingresso CD differenziale ad alta qualit Tre DAC stereo supportano il formato PCM a 16/20/24 bit per soluzioni audio a 5.1 canali Supporta ADC con sample rate di 44.1k/48k/96k Conforme ai requisiti audio di WHQL e WLP 3.1x di Microsoft Compatibile con Direct Sound 3DTM
Audio
Multi-Language Translation
Italiano
Questa scheda madre utilizza un tipo LGA775 di Intel CoreTM2 Duo/Pentium D/Pentium 4/ Celeron D che offre le seguenti caratteristiche: Alloggia processori Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D Supporto di un bus di sistema (FSB) da 1066/800/533 MHz Supporto di CPU con tecnologia Hyper-Threading La tecnologia Hyper-Threading simula per il sistema operativo una sorta di doppio processore e consente a due processi di essere eseguiti in parallelo, ciascuno su un diverso processore logico allinterno del medesimo processore sico.
La funzionalit LAN integrata sulla scheda offre le seguenti caratteristiche: Supporto di NWay Auto-negotiation a 10/100 Mb/s Supporto di funzionalit Wake-on-LAN e riattivazione remota Supporto di funzionalit half/full duplex Supporto di NWay Auto-negotiation a 10Mb/s e 100 Mb/s Soluzione livello sico 100Base-TX/10Base-T a chip unico Supporto di funzionalit half/full duplex Transceiver 10/100/1000 integrato Supporta PCI v2.3, 32-bit, 33/66-MHz Completamente conforme con lIEEE 802.3,IEEE 802.3u, IEEE 802.3ab
Italiano
Conforme a host controller Single Chip per IEEE1394-1995 e IEEE1394a2000 PHY a 2 porte da 400 Mb/s integrato per il bus PCI Alimentazione a 3,3 V con ingressi dotati di tolleranza di 5 V
Opzioni di espansione
La scheda madre dotata delle seguenti opzioni di espansione: Uno slot PCI Express x16 per interfaccia graca Uno slot PCI Express x1 Due slot PCI v2.3 a 32 bit Due connettori a basso prolo IDE a 40 pin per il supporto di no a quattro dispositivi IDE Uninterfaccia per unit disco oppy Due connettori SATA a 7 pin Questa scheda madre supporta bus master UltraDMA con tasso di trasferimento di 133/100/66 MB/s.
I/O integrati
La scheda madre offre una serie completa di porte e connettori I/O: Due porte PS/2 per mouse e tastiera Una porta seriale Una porta parallela Una porta VGA Una porta 1394a (opzionale) Quattro porte USB Una porta LAN (opzionale) Prese jack audio per microfono, line-in e line-out a 6/8 canali (opzionale)
Firmware BIOS
La scheda madre si avvale del BIOS AMI che consente la congurazione personalizzata di molte funzionalit del sistema, tra cui: Gestione dellalimentazione Allarmi di attivazione Parametri CPU Sincronizzazione di CPU e memoria Il rmware consente inoltre di impostare i parametri per diverse velocit di clock del processore. Alcune speciche hardware e voci di software possono essere modicate senza preavviso.
Multi-Language Translation
Caracterstica Procesador
Chipset
El chipset P4M900 Northbridge (NB) y VT8237A/VT8237S Southbridge (SB) se basa de una arquitectura innovadora y escalable con el rendimiento y abilidad comprobados.
P4M900 (NB)
Memoria
Soporta modos de transferencia 66 MHz, 4x/8x, interfaz U ltra V-Link Host con la ancha de banda total de 533 MB/s Soporta hasta dos puertos PCI Express, congurado como una lnea x16 y una lnea x1 PCI Express Controlador de Grcas & Vdeo 3D/2D UniChrome Pro Integrado Controlador 64-bit DDR2/DDR SDRAM avanzado Conformidad de ACPI 2.0 y PCI Bus Management 1.1 Soporta interfaz 16-bit 66 MHz Ultra V-Link Host con ancha de banda total de 1GB/s Conforme con la especicacin PCI 2.3 en 33 MHz, que soporta hasta 6 msters de PCI Controladores Antriones Serial ATA/ Serial ATA II integrados, soporta ndices de transferencia de datos hasta 1.5/3.0 Gb/s (Serial ATA II con VT8237S solamente) Controlador EIDE del Modo Mster UltraDMA 133/100/66 de Canal Dual integrado Controlador USB 2.0, con soporte para 8 puertos USB 2.0 Controlador de teclado integrado con soporte de ratn PS2
Soporta SDRAM DIMMs de DDR2 667/533/400 DDR2 Acomoda dos DIMMS DDR2 sin buffer Hasta 2 GB por DIMM con el tamao de memoria mximo hasta 4 GB
Audio
Esta placa principal puede soportar uno de los sigtes. chipset Audio: 8 canales de formato PCM de 16/20/24-bit de soporte DAC para la solucin de audio 7.1 Todos los ADCs soportan ndice de Muestreo Independiente de 48K/192kHz Excede los Requisitos de Microsoft PC2001 Entrada de CD diferencial de alta calidad Tres DACs Estreo soportan formato PCM de 16/20/24-bit para la solucin de audio de canal 5.1 ADCs soportan ndice de muestreo de 44.1k/48k/96k Satisface los requisitos de audio de Microsoft WHQL/WLP 3.1x Compatible con Direct Sound 3DTM
Multi-Language Translation
Espaol
Esta placa principal usa un tipo LGA775 de Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D que lleva las sigtes caractersticas: Acomoda procesadores Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D Soporta un bus de sistema (FSB) de 1066/800/533 MHz Soporta la CPU con tecnologa "Hyper-Threading" La tecnologa Hyper-Threading habilita el sistema operativo en pensar que est conectado a dos procesadores, que permite dos hilos a correr en paralelo, ambos en procesadores "lgicos" separados dentro de un mismo procesador fsico.
El controlador LAN abordo provee las sigtes. caractersticas: Soporta operacin de Autonegociacin N-Way de 10/100 Mb/s Soporta la funcin Wake-On-LAN y despertar remoto Soporta capacidad duplex medio/completo Soporta operacin de Autonegociacin N-Way de 10Mb/s y 100Mb/s Solucin de capa fsica de 100Base-TX/10Base-T de un solo chip Soporta capacidad duplex medio/completo Transceptor 10/100/1000 integrado Soporta PCI v2.3, 32-bit, 33/66-MHz Soporte completo con el IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Espaol
Conformidad con un controlador antrin de un solo chip para IEEE 1394-1995 y IEEE1394a-2000 400 Mb/s 2-Port PHY integrado para el Bus PCI Suministro de 3.3V con Entradas Tolerantes de 5V
Opciones de Expansin
La placa principal viene con las sigtes. opciones de expansin: Un ranura PCI Express x16 para la Interfaz de Grcas Una ranura PCI Express x1 Dos ranuras conforme con 32-bit PCI v2.3 Dos conectores de bajo perl IDE de 40-pin que soporta hasta 4 dispositivos IDE Una interfaz de la unidad de disco oppy Dos conectores SATA de 7-pin Esta placa principal soporta el mastering de bus UltraDMA con ndices de transferencia de 133/100/66 MB/s.
I/O Integrado
La placa principal tiene un juego completo de puertos y conectores I/O: Dos puertos PS/2 para ratn y teclado Un puerto serial Un puerto paralelo Un puerto VGA Un puerto 1394a (optativo) Cuatro puertos USB Un puerto LAN (optativo) Clavijas de Audio para micrfono, line-in y line-out de 6/8-canales (opcional)
BIOS Firmware
La placa principal usa AMI BIOS que habilita usuarios para congurar muchas caractersticas de sistema que incluyen las sigtes: Administracin de Alimentacin Alarmas para despertar Parmetros de CPU Cronometraje de CPU y de memoria Tambin se lo puede usar el rmware para congurar los parmetros para diferentes velocidades de reloj de procesador. Algunas especicaciones de hardware e tems de software son sujetos a cambio sin aviso previo.
Multi-Language Translation
Caractersticas Processador
Esta motherboard usa um tipo LGA775 de Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D que possui as seguintes caractersticas: Acomoda processadores Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D Suporta um bus de sistema (FSB) de 1066/800/533 MHz Suporta CPU de tecnologia Hyper Threading Tecnologia Hyper Threading que permite ao sistema funcionar de forma interligada at dois processadores, permitindo que os dois os possam funcionar em paralelo, ambos em processadores lgicos separados dentro do mesmo processador fsico.
Conjunto de Chips
Um conjunto de chips P4M900 Northbridge (NB) e VT8237A/VT8237S Southbridge (SB) baseado numa arquitectura inovadora e escalvel com uma performance comprovadamente credvel. Suporta modos de transferncia 66 MHz, 8X/4X, interface P4M900 Ultra V-Link Host com largura de banda total de 1 GB/seg. (NB) Suporta at duas portas PCI Express, congurado como uma x16 e uma x1 via PCI Express Grcos Chrome9 HC 3D/2D Integrados & Controlador de Vdeo Controlador DDR SDRAM e DDR2 Avanado de 64 bits Compatvel com ACPI 2.0 e Gesto de Bus PCI 1.1 VT8237A /VT8237S (SB) Suporta um interface 66 MHz Ultra V-Link Host de 16 bits com largura de banda total de 1 GB/seg. Compatvel com especicao PCI 2.3 a 33 MHz, suportando mais de 6 PCI mestres ATA de Srie integrado/ Controladores Host ATA II de Srie, suportando taxas de transferncia de dados at 1.5/3.0 Gb/seg. (ATA II de Srie com somente VT8237S) Canal Duplo Integrado UltraDMA 133/100/66 Modo Mestre EIDE Controlador Controlador USB 2.0, suportando portes para 8 USB 2.0 Controlador de teclado integrado com suporte para mouse PS2
Memria
Suporta DDR2 667/533/400 DDR2 SDRAM DIMMs Acomoda duas DDR2 DIMMs sem buffers At 2 GB por DIMM com tamanho de memria mxima de at 4 GB
udio
Esta motherboard poder suportar qualquer um dos seguintes conjuntos de chips Audio: Formato 16/20/24-bit PCM com suporte DAC de 8 canais para soluo udio 7.1 Todos os ADCs suportam uma Taxa de Amostragem Independente de 48K/192kHz Excede os requisitos Microsoft PC2001 Entrada de CDs de diferencial de alta qualidade Trs DACs Estreo que suportam 16/20/24-bits e formato PCM para soluo udio canal 5.1 ADCs suportam taxa de amostragem de 44.1k/48k/96k Cumpre com os requisitos udio WHQL/WLP 3.1x da Microsoft audio Compatvel com Direct Sound 3DTM
Multi-Language Translation
Portugus
Esta motherboard poder suportar qualquer um dos seguintes conjuntos de chips LAN: Suporta operao de Auto-negociao N-Way 10/100 Mb/s Suporte Wake-on-LAN ( WOL) e wake-up remoto Suporta capacidade de duplex pela metade/ou na totalidade Suporta operao de Auto-negociao N-Way 10Mb/s e100Mb/s Soluo de passagem 100Base-TX/10Base-T fsica com um nico chip Suporta capacidade de duplex pela metade/ou na totalidade Transreceptor integrado 10/100/1000 Suporta PCI v2.3, 32-bit, 33/66-MHz Suporta inteiramente com IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Portugus
Opes de Expanso
A motherboard fornecida com as seguintes opes de expanso: Um ranhura PCI Express x16 para Interface de Grcos Uma ranhura PCI Express x1 Dois ranhuras compatveis com PCI v2.3 de 32 bits Dois conectores de baixo perl IDE de 40 pinos suportando at 4 dispositivos IDE Um interface com drive de disco exvel Dois conectores SATA de 7 pin Esta motherboard suporta um domnio bus UltraDMA bus com taxas de Transferncia de 133/100/66 MB/s.
I/O Integrado
A motherboard possui um conjunto completo de portas I/O e conectores: Duas portas PS/2 para rato e teclado Uma porta de srie Uma porta paralela Uma porta VGA Uma porta 1394a (opcional) Quatro portas USB Uma porta LAN (opcional) Fichas udio para microfone, line-in e line-out de 6/8-canais (opcional)
Microprogramao BIOS
Esta motherboard usa AMI BIOS que permitem aos utilizadores congurar muitas caractersticas do sistema incluindo as seguintes: Gesto de corrente Alarmes de despertar Parmetros CPU Temporizao de memria e CPU A microprogramao poder ser tambm usada para estabelecer parmetros para diferentes velocidades de relgio do processador. Algumas especicaes de hardware e itens de software podero ser sujeitos a alteraessem aviso prvio.
Multi-Language Translation
Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D LGA775 Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D 1066/800/533 MHz(FSB) HT 2 21
P4M900 Northbridge (NB) VT8237A/VT8237S Southbridge (SB) P4M900 66 MHz 4X8 Ultra V-Link 1 GB/ (NB) 2PCI Expressx16x1PCI Express Chrome9HC 3D/2D Graphics & Video 64DDR2 DDR SDRAM ACPI 2.0 and PCI Bus Management 1.1 1666 MHzUltra V-Link 1 GB/ VT8237A/ VT8237S 33MHzPCI 2.36PCI (SB) ATA/ ATA II 1.5/3.0 Gb/ (ATA II VT8237S) UltraDMA133/100/66 EIDE USB2.08USB2.0 PS2
Multi-Language Translation
LAN
LAN 10/100 Mb/s N-way Wake-on-LANWOL) / 10Mb/s 100Mb/s N-way 100Base-TX/10Base-T / 10/100/1000 PCI v2.3, 32-bit, 33/66MHz IEEE 802.3IEEE 802.3uIEEE 802.3ab
BIOS
AMI BIOS CPU CPU
Multi-Language Translation
LGA775 Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D : Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D 1066/800/533 MHz (FSB) "Hyper-Threading" CPU "Hyper-Threading" , "" .
P4M900 (NB)
66 MHz, 8X/4X , UltraV-Link 1 GB/s 2 PCI Express (x16 + PCI Express lane) Chrome9 HC 3D/2D 64 DDR2/DDR SDRAM ACPI 2.0 PCI Bus Management 1.1 16 66 MHz Ultra V-Link 1 GB/s 33 MHz PCI 2.3 , 6 PCI Serial ATA/ Serial ATA II , 1.5/3.0 Gb/s (VT8237S Serial ATA II ) UltraDMA 133/100/66 EIDE USB 2.0 , 8 USB 2.0 PS2
DDR2 667/533/400 DDR2 SDRAM DIMM 2 DDR2 unbuffered DIMM DIMM 2 GB, 4 GB
: 8 DAC, 7.1 16/20/24 PCM ADC 48K/192kHz Microsoft PC2001 CD 3 DAC` 5.1 16/20/24 PCM ADCs 44.1k/48k/96k WHQL/WLP 3.1x Direct Sound 3DTM
Multi-Language Translation
LAN ( )
LAN : 10/100 Mb/s N-Way Auto-negotiation Wake-on-LAN wake-up Half/full 10Mb/s 100Mb/s N-Way Auto-negotiation 100Base-TX/10Base-T Half/full 10/100/1000 PCI v2.3, 32-bit, 33/66-MHz IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
1394a ( )
IEEE 1394-1995 IEEE1394a-2000 PCI 400 Mb/s 2 PHY 3.3V (5V )
: 32 PCI v2.3 2 4 IDE 40 IDE low profile 2 1 7 SATA 2 133/100/66 MB/s UltraDMA .
PCI x16 1 PCI Express x1 1
I/O
I/O : PS/2 2 1 1 VGA 1 1394 a 1 ( ) USB 4 LAN 1 ( ) (, 6/8 () )
BIOS
AMI BIOS : Wake-up CPU CPU .
Multi-Language Translation
Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D LGA775 Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D 1066/800/533 MHz(FSB) (Hyper-Threading)CPU (HT)
P4M900 (NB)VT8237A/VT8237S (SB) 66 MHz4X8XUltra V-Link P4M900 1 GB/ (NB) PCI Expressx16 x1 PCI Express Chrome9 HC 3D/2D 64 DDR2 DDR SDRAM ACPI 2.0PCI 1.1 1666 MHzUltra V-Link VT8237A/ 1GB/ VT8237S 33MHzPCI v2.3(6PCI) (SB) ATA/ATA II 1.5/3.0 Gb/ (ATA IIVT8237S) Ultra 133/100/66EIDE USB2.0(8USB2.0) PS2
8DAC 7.116/20/24-PCM ADC 48K/192kHz Microsoft PC2001 CD 3(DAC)5.1 16/20/24PCM (ADC)44.1k/48k/96k Microsoft WHQL/WLP 3.1x Direct Sound 3DTM
Multi-Language Translation
LAN 10Mb/s 100Mb/s N-way (WOL) / 10Mb/s 100Mb/s N-way 100Base-TX/10Base-T / 10/100/1000 PCI v2.3, 32, 33/66 MHz IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
1PCI Express x16 1PCI Express x1 232PCIv2.3 240IDE4 IDE 1 27SATA 133/100/66 MB/Ultra DMA
I/O
I/O 2 PS/2 1 1 1 VGA 1 1394a() 4 USB 1 () Line6/8()Line
BIOS
AMI BIOS CPU CPU
Multi-Language Translation
LGA775 Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D CPU Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D 1066/800/533 MHz (FSB) CPU
P4M900 (NB) VT8237A/VT8237S (SB) P4M900 66 MHz 4x 8x Ultra V-Link (NB) 1GB/s 2 PCI Express x16 x1 PCI Express lane Chrome9 HC 3D/2D & 64 DDR2 DDR SDRAM ACPI 2.0 PCI 1.1 VT8237A/ VT8237S (SB) 16 66 MHzUltra V-Link 1 GB/sec 33 MHz PCI 2.3 6 PCI Serial ATA/ Serial ATA II 1.5/3.0 Gb/s Serial ATA II VT8237S UltraDMA 133/100/66 EIDE USB 2.0 8 USB 2.0 PS2
8 DAC 16/20/24 PCM 7.1 ADC 48K/192kHz Microsoft PC2001 CD 3 DAC 16/20/24 PCM 5.1 ADC 44.1k/48k/96k Microsoft WHQL/WLP 3.1x Direct Sound 3DTM
Multi-Language Translation
Onboard LAN
LAN 10Mb/s 100Mb/s N LAN (WOL) / 10Mb/s 100Mb/s N 100Base-TX/10Base-T / 10/100/1000 PCI v2.332-33/66-MHz IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
1394a
IEEE1394-1995 IEEE1394a-2000 PCI PCI 400 Mbit 2 PHY 3.3V 5V
1 PCI Express x16 1 PCI Express x1 2 32 PCI v2.3 2 40-pin IDE 4 IDE 1 2 7-pin SATA Ultra DMA 133/100/66MB/s
I/O
I/O 2 PS/2 1 1 1 VGA 1 1394a 4 USB 1 LAN 6/8
BIOS
AMI BIOS CPU CPU .
Multi-Language Translation
Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D LGA775 : Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D (FSB) 1066/800/533 MHz CPU Hyper-Threading Hyper-Threading , ; , .
P4M900 (NB)
66 M, 4X/8X, Ultra V-Link 1G/ PCI Express, x16 x1 PCI Express Chrome9 HC 3D/2D 64- DDR2/DDR SDRAM ACPI 2.0 PCI Bus Management 1.1
A : 8- DAC 16/20/24- PCM . 7.1 ADC 48K/192 Microsoft PC2001 CD -DAC 16/20/24- PCM 5.1 ADC 44.1k/48k/96k Microsoft WHQL/WLP 3.1x Direct Sound 3DTM
Multi-Language Translation
16- 66 M Ultra V-Link 1/ PCI 2.3 33 MHz, 6 PCI master Serial ATA/ Serial ATA II, 1,5/3,0 / ( Serial ATA II VT8237S) UltraDMA 133/100/66 Master Mode EIDE USB 2.0, 8 USB 2.0 PS2
LAN ()
LAN :
10/100 Mb/s
10/100/1000 PCI v2.3, 32-, 33/66-M IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
1394a FireWire ()
IEEE 1394-1995 IEEE1394a-2000 400 Mb/s 2- PHY PCI 3.3 5
32- PCI v2.3 40- IDE 4 IDE 7-pin SATA UltraDMA bus mastering 133/100/66 /.
/ :
BIOS
AMI BIOS, :
BIOS .
CPU CPU
Multi-Language Translation
Cechy Procesor
Pyta gwna obsuguje procesory Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D typu LGA775 i posiada nastpujce waciwoci: Przystosowana do obsugi procesorw Intel CoreTM2 Duo/Pentium D/ Pentium 4/Celeron D Obsuguje szyn systemowa (FSB) 1066/800/533 MHz Zabezpiecza technologi CPU Hyper-Threading Technologia Hyper-Threading powoduje, e system "myli, e posiada dwa procesory i wykonuje rwnolegle dwa procesy; za wykonanie kadego procesu odpowiedzialny jest jeden z dwuch "logicznych" procesorw w ramach jednego zycznego procesora
Chipset
Mostek pnocny (NB) P4M900 i mostek poudniowy VT8237A/VT8237S chipsetu s zbudowane w oparciu o innowacyjn architektur skalowaln o potwierdzonej niezawodnoci i solidnym wykonaniu. Obsuguje 66 MHz tryby przesyania 8X/4X, interfejs hosta P4M900 Ultra V-Link o cakowitej przepustowoci 1 GB/s (NB) Obsuguje do dwu portw PCI Express, z ktrych jeden jest skongurowany jako PCI Express x16, a drugi jako PCI Express x1 Zintegrowany kontroler graki i video Chrome9 HC 3D/2D Zaawansowany kontroler 64-bitowy DDR2/DDR SDRAM Zgodne z ACPI 2.0 oraz PCI Bus Management 1.1
Pami
Obsuguje banki pamici DDR2 533/400 DDR2 SDRAM DIMM Zaopatrzony w dwa gniazda niebuforowanej pamici typu DDR2 DIMM Obsuguje pami DIMM do pojemnoci 2 GB kada; maksymalna moliwa pojemno pamici do 4 GB
Audio
Multi-Language Translation
Polski
Obsuguje 16 bitowy, 66 MHz interfejs hosta Ultra V-Link o cakowitej przepustowoci 1 GB/s Zgodny ze standardem PCI w wersji 2.3 o czstotliwoci 33 MHz, obsuguje do 6 urzdze PCI typu master. Zintegrowane kontrolery Serial ATA/ Serial ATA II zapewniajce szybkoci przesyania do 1,5/3,0 Gb/s (tylko Serial ATA II z VT8237S) Zintegrowany dwukanaowy kontroler UltraDMA 133/100/66 w trybie Master EIDE Kontroler USB 2.0, obsugujcy do 8 gniazd USB 2.0 Zintegrowany kontroler klawiatury z obsug myszy PS2
Zintegrowany terminal nadawczo-odbirczy 10/100/1000 Obsluguje 32 bitowe PCI w wersji 2.3 o czstotliwociach 33/66-MHz Obsuguje wpeni standard IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Moliwoci rozbudowy
Pyta gwna wyposaona jest w nastpujce gniazda: Jedno gniazdo PCI Express x16 dla karty gracznej Jedno gniazdo PCI Express x1 Dwa 32-bitowych gniazda zgodnych z PCI w wersji 2.3 Dwa 40-nkowe zcza niskoprolowe IDE obsugujce do 4 urzdze IDE Jedno zcze obsugujce stacje dyskietek Dwa 7-nkowe zcza SATA
Zintegrowane We/Wy
Pyta gwna wyposaona jest w peny zestaw gniazd i zczy We/Wy: Dwa gniazda PS/2 dla myszy i klawiatury Jedno gniazdo szeregowe Jedno gniazdo rwnolege Jedno gniazdo VGA Jedno gniazdo 1394a (opcjonalnie) Cztery gniazda USB Jedno gniazdo LAN (opcjonalnie) Gniazda typu Jack dla mikrofonu, 6/8-kanaowego wejcia (opcjonalnie) oraz wyjcia
Polski
Firmowy BIOS
Pyta gwna wyposaona jest w BIOS rmy AMI, ktry pozwala uytkownikowi kongurowa wiele cech systemu wczajc w to nastpujce waciwoci: Zarzdzanie poborem mocy Alarmy typu Wake-up Parametry pracy procesora Ustalenia szybkoci pracy procesora i pamici BIOS moe by uywany do ustalania parametrw wpywajcych na szybkoci pracy zegara procesora.
Niektre parametry dotyczce pyty i jej oprogramowania mog ulec zmianie bez uprzedniego powiadomienia.
Multi-Language Translation
Vlastnosti Procesor
Tato zkladn deska je urena pro procesory Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D LGA775 a me nabdnout nsledujc vlastnosti: Pouit pro procesory Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D s jdrem Podporuje taktovn systmov sbrnice (FSB) na frekvenci 1066/800/533 MHz Podporuje technologii CPU Hyper-Threading Technologie Hyper-Threading umouje operanmu systmu pracovat tak, jako by byl pipojen ke dvma procesorm, protoe je mon pracovat se dvma toky programovho kdu (vlkny) paraleln najednou, piem jsou k dispozici samostatn logick procesory umstn v rmci jednoho fyzickho procesoru.
ipy northbridge (NB) P4M900 a southbridge (SB) VT8237A/VT8237S jsou zaloeny na inovativn a klovateln architektue s ovenou spolehlivost a vkonnost. P4M900 Podpora hostitelskho rozhran 66 MHz, penosov reimy 4x/8x, Ultra V-Link s celkovou kou psma 1 GB/s (NB) Podporuje a dva sloty PCI Express, kongurovan jako jedna trasa x16 a jedna trasa x1 PCI Express Integrovan adi graky a videa Chrome9 HC 3D/2D Modern 64bitov adi pamt DDR2 a DDR SDRAM Sluiteln s ACPI 2.0 a PCI Bus Management 1.1 VT8237A Podpora rozhran Ultra VLink 16bit 66 MHz s celkovou kou psma 1 GB/s /VT8237S Spluje specikace standardu PCI 2.3 s frekvenc 33 MHz, (SB) podporujc a 6 hlavnch kanl PCI Integrovan adie Serial ATA/ Serial ATA II, podpora rychlosti penosu dat a 1,5/3,0 Gb/s (jen adi Serial ATA II s ipem VT8237S) Integrovan dvoukanlov adi UltraDMA133/100/66 EIDE v dcm reimu. adi USB 2.0, podporujc 8 port USB 2.0 Integrovan adi klvesnice s podporou myi PS2
ipov sada
Pam esky
Podpora pamovch modul DDR2 667/533/400 DDR2 SDRAM DIMM Instalovat je mon a dv DDR2 DIMM moduly bez vyrovnvac pamti A 2 GB pamti na jeden modul DIMM s maximln velikost pamti do 4 GB
Vestavn sov rozhran zvukov nabz nsledujc monosti: 8 kanl pevodnku DAC podporuje 16/20/24bitov formt PCM pro zvukov vstup 7.1 Vechny A/D pevodnky podporuj nezvisl vzorkovn 48 K/192 kHz S rezervou vyhovuj poadavkm Microsoft PC2001 Vysoce kvalitn diferenn vstup CD 3 stereo pevodnky DAC podporuj 16/20/24bitov formt PCM pro zvukov vstup 5.1 Podpora ADC se vzorkovac frekvenc 44.1k/48k/96k Spluje poadavky pro audio zazen Microsoft WHQL/WLP 3.1x Kompatibilita s Direct Sound 3DTM
Zvukov
Multi-Language Translation
Shoda se standardem jednoipovho adie IEEE 1394-1995 a IEEE1394a-2000 2 integrovan porty 400 Mb/s PHY pro sbrnici PCI Podporuje napjen 3,3 V s toleranc vstupu 5 V
Monosti rozen
Zkladn deska je dodvna s nsledujcmi monostmi rozen Jedna patice PCI Express x16 pro grackou kartu Jedna patice PCI Express x1 Dva 32bitov patice PCI v2.3 Dva nzkoprolov 40kolkov konektory IDE podporujc pipojen 4 zazen standardu IDE Jedno rozran pro disketovou mechaniku Dva 7kolkov konektor SATA Zkladn deska podporuje sbrnici Ultra DMA s penosovmi rychlostmi 133/100/66 MB/s.
Integrovan vstup/vstup
Zkladn deska je vybavena kompletn sadou vstupnch port a konektor I/O: Dva porty PS/2 pro my a klvesnici Jeden sriov port Jeden paraleln port Jeden port VGA Jeden port LAN (voliteln) tyi porty USB Jeden port LAN (voliteln) Audio konektory mikrofonu, linkovho vstupu a 6/8kanlovho (voliteln) linkovho vstupu
esky
Firmware BIOS
Zkladn deska vyuv BIOS formy AMI, kter uivateli umouje nakongurovat mnoho systmovch parametr, vetn nsledujcch: zen spoteby Alarmy pi spoutn systmu Parametry CPU asovn CPU a pamti Firmware me bt rovn pouit k nastaven parametr pro rzn taktovac frekvence procesoru. Nkter technick parametry hardware a software se mohou mnit bez pedchozho upozornn.
Multi-Language Translation
Caracteristici Procesorul
Aceast plac de baz utilizeaz un Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D de tip LGA775 cu urmtoarele caracteristici: Funcioneaz cu procesoare Intel CoreTM2 Duo/Pentium D/Pentium 4/ Celeron D Funcioneaz cu bus sistem (FSB) de 1066/800/533 MHz Este compatibil cu uniti centrale dotate cu tehnologia HyperThreading Tehnologia Hyper-Threading permite sistemului de operare s funcioneze ca i cum ar exista dou procesoare, putnd rulate n paralel dou re, ecare pe cte un procesor logic separat, aate pe acelai procesor zic.
Setul de chipuri
Chipsetul P4M900 Northbridge (NB) i VT8237A/VT8237S Southbridge (SB) se bazeaz pe o arhitectur inovatoare i dezvoltat cu abilitate i performan demonstrate. P4M900 suport pentru moduri de transfer 66 MHz, 4x/8x, interfa Ultra V-Link Host cu lime de band total de 1 GB/s (NB) Suport pn la dou porturi PCI Express, congurat ca i un x16 i unu x1 PCI LANE-uri Express Controller grac & video Chrome9 HC 3D/2D integrat Controller 64-bit DDR2/DDR SDRAM avansat Compatibil cu ACPI 2.0 i PCI Bus Management 1.1 VT8237A/ suport pentru interfa 16-bit 66 MHz Ultra V-Link Host cu lime de band total de 1 GB/s VT8237S Compatibil cu specicaia PCI, versiunea 2.3 33MHz, care (SB) suport cel mult 6 module PCI master Serial ATA/ Serial ATA II Host Controller-uri integrate, care suport rate de transferuri de dat de pn la 1.5/3.0 Gb/s (Serial ATA II cu VT8237S numai) Controler EIDE UltraDMA 133/100/66 Master Mode integrat cu canal dual Controler USB 2.0 care suport 8 porturi USB 2.0 Controler de tastatur cu suport pentru mouse PS/2
Memoria
Suport pentru DIMM-uri DDR2 667/533/400 DDR2 SDRAM Poate funciona cu dou module DDR2 DIMM fr zon tampon Poate funciona cu module DIMM de cel mult 2 GB, iar cantitatea maxim de memorie este de 4 GB
Suport DAC 8 canale format PCM 16/20/24-bit pentru soluii audio 7.1 Toate ADC-urile suport 48K/192kHz Independent Sample Rate Excede Cerinele Microsoft PC2001 input CD diferenial nalt calitate Trei DAC-uri stereo 16/20/24-bit format PCM pentru soluie audio 5.1 canale Suport ADC-uri la vitez de eantionare 44.1k/48k/96k Corespunde cerinelor audio Microsoft WHQL/WLP 3.1x Compatibil cu Direct Sound 3DTM
Multi-Language Translation
Romn
Audio
Onboard LAN are urmtoarele caracteristici: Suport operaii de autonegociere N-way de 10/100 Mb/s Suport pentru funciile Wake-on-LAN ( WOL) i trezire la distan Posibilitate semi-duplex i duplex complet Suport operaii de autonegociere N-way de 10Mb/s i 100 Mb/s Soluie cu start zic cu un singur cip 100Base-TX/10Base-T physical layer solution Posibilitate semi-duplex i duplex complet Unitate de emisie/recepie 10/100/1000 integrat Suport PCI, versiunea 2.3, de 32 bii, la 33/66 MHz compatibil pe deplin cu standardul IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Opiuni de extindere
Placa de baz este dotat urmtoarele posibiliti de extindere: Un slot PCI Express de 16x pentru interfaa grac Un slot PCI Express x1 Dou sloturi de 32 bii compatibile PCI, versiunea 2.3 Dou socluri IDE plate de 40 de ace care suport cel mult patru uniti IDE O interfa pentru unitate oppy Dou conectoare SATA plate de 7 Placa de baz suport bus mastering UltraDMA cu viteze de transfer de 133/100/66 MB/s
I/O integrat
Placa de baz este dotat cu un set complet de porturi i conectoare I/O: Dou porturi PS/2, pentru mouse i tastatur Un port serial Un port paralel Un port VGA Un port 1394a (opional) Patru porturi USB Un port LAN (opional) Fi audio pentru microfon, priz de intrare i priz de ieire 6/8-canale (opional)
Romn
Firmware BIOS
Placa de baz utilizeaz AMI BIOS, care permite utilizatorului s congureze mai muli parametri ai sistemului, cum ar : Gestionarea energiei Alarme de trezire Parametri CPU Temporizare CPU i memorie Acest rmware poate utilizat i pentru a seta parametrii diferitelor frecvene de comand ale procesorului. Anumite specicaii hardware i elemente de software pot modicate fr ntiinare prealabil.
Multi-Language Translation
LGA775 Intel CoreTM2 Duo/Pentium D/ Pentium 4/Celeron D : Intel CoreTM2 Duo/Pentium D/Pentium 4/ Celeron D 1066/800/533 MHz Hyper-Threading" Hyper-Threading" , , .
P4M900 VT8237A/VT8237S . P4M900 66 MHz, 4x/8x, Ultra (NB) V-Link 1GB/s PCI Express ( 16 1) Chrome9 HC 3D/2D 64- DDR2/DDR SDRAM ACPI 2.0 PCI Bus Management 1.1 16- Ultra V-Link Host , 66 VT8237A /VT8237S MHz, 1 GB/sec (SB) PCI 2.3 33 MHz, 6 PCI master Serial ATA/ Serial ATA II host , 1.5/3.0 Gb/s (Serial ATA II VT8237S) - EIDE UltraDMA 133/100/66 Master Mode USB 2.0 8 USB 2.0 PS2
: 8- - 16/20/24-bit PCM 7.1 . - (DAC) 48K/192kHz Microsoft PC2001 CD- DAC 16/20/24 PCM 5.1 ADC- 44.1k/48k/96k - Microsoft WHQL/WLP 3.1x Direct Sound 3DTM
Multi-Language Translation
()
10/100 Mb/s, N-Way Auto-negotiation operation Wake-On-LAN wake-up : Half/Full duplex 10Mb/s 100Mb/s, N-Way Auto-negotiation operation LAN 100BaseTX/10Base-T : Half/Full duplex 10/100/1000 PCI v2.3, 32-bit, 33/66-MHz IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
1394a FireWire ()
: E PCI Express x16 PCI Express x1 32-bit PCI v2.3 40-pin IDE 4 IDE 7- SATA s UltraDMA 133/100/66 MB/s
BIOS Firmware
Multi-Language Translation
Jellemz Processzor
Ez az alaplap LGA775 tpus Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D-et hasznl, amely a kvetkez tulajdonsgokkal rendelkezik: Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D processzorokkal mkdik 1066/800/533 MHz sebessg rendszerbuszt (FSB) tmogat Tmogatja a Hyper-Threading technolgit hasznl kzponti egysgeket A Hyper-Threading technolgia ltal az opercis rendszer gy mkdik, mintha kt processzorral rendelkezne, ami kt szl prhuzamos futst teszi lehetv kt fggetlen, ugyanazon zikai processzoron tallhat logikai processzoron. A P4M900 Northbridge (NB) s a VT8237A/VT8237S Southbridge (SB) chip-kszlet bizonytott megbzhatsg s teljestmny j s fejlesztett architektrra pl. megfelel 66 MHz, 4X/8X transzfer mdoknak, Ultra V-Link Host P4M900 1GB/s teljes svszlessg interfssze (NB) Akr kt PCI Express portot is tmogat, ha ezek egy x16-knt s egy x1 PCI Express LANE hlzatknt vannak kongurlva integrlt Chrome9 HC 3D/2D grakai & video vezrl fejlett 64-bites DDR2/DDR SDRAM vezrl ACPI 2.0 s PCI Bus Management 1.1 megfelels
Lapkakszlet
Memria
megfelel 16-bit 66 MHz Ultra V-Link Host 1Gb/s teljes svszlessg interfsznek A PCI 2.3 specikcival kompatibilis 33 MHz-en, maximum 6 PCI mastert tmogat Integlt soros ATA/ Soros ATA II Host Controllerek, melyek egszen 1.5/3.0 Gb/s-os adattvitelt tmogatnak (kizrlag Soros ATA II VT8237S-el) Beptett dul csatorns UltraDMA 133/100/66 Master md EIDE vezrl USB 2.0 vezrl, 8 USB 2.0 portot tmogat Beptett billentyzet-vezrl, PS/2 egr tmogatsa
Megfelel DDR2 667/533/400 DDR2 SDRAM DIMM-eknek Kt puffermentes DIMM DDR2 egysggel mkdik Maximum 2 GB-os DIMM egysgeket tmogat, maximlis memria 4 GB
Audio
Ez az alaplap a kvetkez Audio lapkakszletek brmelyikt tmogatja. 8 csatorns DAC tmogats 16/20/24-bit PCM formtum 7.1 hangberendezsre Az sszes ADC tmogatja a 48K/192kHz-es fggetlen mintavteli frekvencia Meghaladja a Microsoft PC2001 Kvetelmnyeket j minsg differencil CD input Hrom Stereo DAC tmogats 16/20/24-bit PCM formtummal 5.1 csatorns audio kivitelezshez ADC tmogats 44.1k/48k/96k mintavtelezsi sebessghez Megfelel a Microsoft WHQL/WLP 3.1x audio kvetelmnyeine Kompatibilis a Direct Sound 3DTM technolgival
Multi-Language Translation
Magyar
Megfelel az egy csipes host vezrlnek, az IEEE 1394-1995 s IEEE1394a-2000 specikciknak Integrlt 400 Mb/s 2-Port PHY a PCI buszhoz 3.3V ramforrs 5V tolerns beadssal
Bvtsi lehetsgek
Az alaplap a kvetkez bvtsi lehetsgekkel rendelkezik: Egy PCI Express x16 foglalat a grakus interfsz Egy PCI Express x1 foglalat Kt 32 bites, a PCI 2.3-as vltozatval kompatibilis foglalat Kt 40 ts lapos IDE foglalat, amelyek maximum ngy IDE egysget kpesek kiszolglni Egy hajlkonylemez meghajt interfsz Kt 7 ts SATA csatlakoz Ez az alaplap tmogatja az UltraDMA bus mastering megoldst, 133/100/66 MB/s sebessgen
Beptett I/O
Az alaplapot az I/O portok s csatlakozk teljes kszletvel szereltk fel: Kt PS/2 port az egr s a billentyzet szmra Egy soros port Egy prhuzamos port Egy VGA port Egy 1394a port (vlaszthat) Ngy USB port Egy LAN port (vlaszthat) Audio dugasz a mikrofon szmra, bemeneti s 6/8-csatorns (opcionlis) kimeneti csatlakozk
BIOS Firmware
Az alaplapon lev AMI BIOS segtsgvel a felhasznl a rendszer sok paramtert llthatja be, pldul: Energiagazdlkods bresztsi riasztsok CPU paramterek CPU s memria idzts A rmware segtsgvel a processzor rajel-frekvenciinak paramtereit is bellthatjk. Bizonyos hardverjellemzk s szoftverelemek elzetes bejelents nlkl mdosulhatnak.
Magyar
Multi-Language Translation