Construction Materials Brick
Construction Materials Brick
Construction Materials Brick
Brick:
A brick is rectangular in shape and of size that can be conveniently handled
with one hand. Brick may be made of burnt clay or mixture of sand and lime or of
Portland cement concrete.
A brick is building material used to make walls, pavements and other elements
in masonry construction. Traditionally, the term brick referred to unit composed
of clay, but it is now used to denote any rectangular units laid in mortar. A brick can
be composed of clay-bearing soil, sand and lime, or concrete materials. Bricks are
produced in numerous classes, types, materials, and sizes which vary with region
and time period, and are produced in bulk quantities. Two basic categories of bricks
are fired and non-fired bricks.
Classification of bricks according to constituent raw material:
1. Clay bricks
2. Lime – sand bricks
3. Glass brick
4. Concrete bricks
1. Clay bricks:
One of the oldest building material brick continues to be a most popular and
leading construction material because of being cheap, durable and easy to handle
and work with. Clay bricks are used for building-up exterior and interior walls,
partitions, piers, footings and other load bearing structures.
Clay brick are essentially made of clay which has some specific properties.
The Plasticity behavior when it mixed with water.
Clay particles fuse together when subjected to high temperature.
Economical and easily available.
Raw materials:
a. Silica (SiO2)
Free silica (sand) is a main constituent, if added to clay in suitable proportion
makes hard and prevents it from warping and shrinkage on drying. Silica, if present
in greater proportion, makes a brick brittle. Silica present in the combined form
(aluminum silicate) does not form good bricks, as it will shrink and develop cracks.
b. Alumina (Al2O3)
Alumina is one of a main constituent of every clay. Loam soil (adhesive soil)
forms good clay. In absence of sand, pure clay will develop cracks due to shrinkage
on drying and burning. A good clay bricks should contain about 20% of alumina.
Alumina absorbs water and renders the clay plastic. If alumina is present in
excess of the specified quantity, it produces cracks in brick on drying. Clays having
exceedingly high alumina content are likely to be very refractory. Both silica and
alumina should be in free form.
C-Lime (CaCO3):
Normally constitutes less than 10 percent of clay. This also should be present
in small quantities in the brick earth. It should be in a finely produced condition and
it should not be in the form lamps or clods. Lime prevents shrinkage of raw bricks
on drying. It helps fusion of sand at the kiln temperature. This fused sand will bind
the bricks particles fast.
d- Iron oxide:
A small quantity of oxide of iron (5-6%) is desirable. It helps the fusion of
sand like lime. It gives red colure to burn bricks. Excess of iron oxide imparts dark
blue or blackish colure to brick, while, a lower percentage of iron oxide makes the
brick yellow in colure. Iron oxide makes the bricks hard and strong.
e. Magnesia:
Rarely exceeding 1 percent affects the colour and makes the brick yellow.
A small amount of magnesia helps to decrease the shrinkage of bricks. This gives a
yellow tint to the bricks. But excess of magnesia is not desirable as it tends to
produce the decay of bricks.
1.2 Composition of good clay brick:
For the preparation of bricks, clay or other suitable earth is moulded to the
desired shape after subjecting it to several processes. After drying, it should not
shrink and no crack should develop. The clay used for brick making consists mainly
of silica and alumina mixed in such a proportion hat the clay becomes plastic when
water is added to it. It also consists of small proportions of lime, iron, manganese,
sulphur, etc. The proportions of various ingredients are as follows:
Silica 50–60%
Alumina 20–30%
Lime 10%
Magnesia < 1%
Ferric oxide < 7% Less than 20%
Alkalis < 10%
Carbon dioxide
Sulphur trioxide Very small percentage
Water
1-3 Harmful ingredients in clay bricks:
A. Excess of lime:
Excess of lime makes the colure of the brick yellow instead of red. Lumps of
limestone remaining in the finished brick are undesirable because, when such a
brick comes in contact with water, lime will begin to slake. During slaking, lime
expands and also generates heat. Due to this, stresses will be produced, which will
result in producing cracks in bricks. Excess of Lime in brick clay has the following
Effects:
1. In carbonated form, lime lowers the fusion point.
2. Excess of lime causes the brick to melt and the brick looses its shape
(dimensional changes).
3. Red bricks are obtained on burning at considerably high temperature (more than
800°C) and buff-burning bricks are made by increasing the lime content.
B. Iron pyrites (FeS2):
These will decompose and oxide the clay during the burning of bricks. After
oxidation a black discoloration will be produced on the bricks, making it look ugly.
C. Pebbles:
The presence of pebbles, girt, gravel etc. will be undesirable because they
prevent the clay from being mixed well. They prevent the manufacture of smooth
and regular, standard bricks. They also spoil the appearance of the bricks. Pebbles,
gravel, grit, etc., should be removed before mixing and pugging of clay are done.
D- Organic matter:
This includes leaves, twigs. Etc. of plants, roots, grass, bones of animals etc.
These if prevent and burnt along with bricks, produced empty pockets or pores and
will produce porous bricks.
E- Alkalis ( MgO , K2O ):
1 .It lowers the fusion temperature and molts bricks
2. Changes the shape of bricks or get twisted.
3. These salts have hygroscopic action, they absorb moisture, present in the
atmosphere and keep brick damp which is harmful for health and decays the
structure.
MgO + H2O Mg (OH)2
K2 O + H2 O 2 KOH
F-Salts:
Salts such as sodium sulphate cause efflorescence. Efflorescence is the
migration of a salt to the surface of a porous material, where it forms a coating.
The essential process involves the dissolving of an internally held salt in water, or
occasionally in another solvent. The water, with the salt now held in solution,
migrates to the surface, and then evaporates, leaving a coating of the salt.
G. Corboaceous :
Corboaceous materials in the form of bituminous matter or carbon greatly
affects the colour of raw clay. Unless proper precaution is taken to effect complete
removal of such matter by oxidation, the brick is likely to have a black core.
H. Sulphur:
Sulphur is usually found in clay as the sulphate of calcium, magnesium,
sodium, potassium or iron, or as iron sulphide. Generally, the proportion is small. If,
however, there is carbon in the clay and insufficient time is given during burning for
proper oxidation of carbon and sulphur, the latter will cause the formation of a
spongy, swollen structure in the brick and the brick will be decoloured by white
blotches.
I. Water: A large proportion of free water generally causes clay to shrink
considerably during drying, whereas combined water causes shrinkage during
Clearly, the only stage during manufacturing, where the size will be a relevant
issue, is when they are formed into their desired shape. In ancient Egypt times, clay
were forming by using their hands, but this changed with the invention of brick
making machines in the 19 th century, where the majority of manufacturing of clay
bricks in America, are machine made.
Manufacture of clay bricks involves the following operation:
1.4.1 Preparation of clay:
a. Removal of loose soil:
The soil used for making building bricks should be processed so as to be free
ofgravel, coarse sand (practical size more than 2 mm), lime and kankar particles,
organic matter, etc. About 20 cm of the top layer of the earth, normally containing
stones, pebbles, gravel, roots, etc., is removed after clearing the trees and
vegetation. The top layer of loose disintegrated soil up to about 20 cm depth has to
be removed as this contains a lot of impurities.
clay would also be eroded by rain to some extent, which otherwise could have
caused scumming at the time of burning of the bricks in the kiln. The soil should be
turned over at least twice and it should be ensured that the entire soil is wet
throughout the period of weathering. In order to keep it wet, water may be sprayed
as often as necessary. The plasticity and strength of the clay are improved by
exposing the clay to weather.
d. Blending:
The earth is then mixed with sandy-earth and calcareous-earth in suitable
proportions to modify the composition of soil. Moderate amount of water is mixed
so as to obtain the right consistency for moulding. The mass is then mixed
uniformly with spades. Addition of water to the soil at the dumps is necessary for
the easy mixing and workability, but the addition of water should be controlled in
such a way that it may not create a problem in moulding and drying. Excessive
moisture content may effect the size and shape of the finished brick. This refers to
mixing the clay, after making it loose and adding any required ingredients to the top
of the heap.
e. Tempering:
This is necessary to make the clay fully consistent, and fit for molding into raw
bricks, by adding the required amount of water to make it plastic. Tempering
consists of kneading the earth with feet so as to make the mass stiff and plastics (by
plasticity, we mean the property which wet clay has of being permanently deformed
without cracking). It should preferably be carried out by storing the soil in a cool
place in layers of about 30 cm thickness for not less than 36 hours. This will ensure
homogeneity in the mass of clay for subsequent processing. For manufacturing
good brick, tempering is done in pug mills and the operation is called pugging Pug
mill consists of a conical iron tube as shown in Fig 2. The mill is sunk 60 cm into
the earth. A vertical shaft, with a number of horizontal arms fitted with knives, is
provided at the centre of the tube. This central shaft is rotated with the help of
bullocks yoked at the end of long arms. However, steam, diesel or electric power
may be used for this purpose. Blended earth along with required water, is fed into
the pug mill from the top. The knives cut through the clay and break all the clods or
lump-clays when the shaft rotates. The thoroughly pugged clay is then taken out
from opening provided in the side near the bottom. The yield from a pug mill is
about 1500 bricks.
Pug mill
1.4.2 Molding:
Molds required for making a brick are made of rectangular blocks slightly large
in size (10% larger than the burnt bricks). It is done to allow for the shrinkage of the
molded brick on drying and burning. The molding is improved by the following
process:
After mining, clay is extruded through a die and trimmed to specify dimensions
before it is sent to the firing chambers. Figure 2 shows a example of the molding
procedure.
The 1 st step in the forming process produces a homogeneous, plastic clay mass,
figure 3 shows how this is achieved by adding water to the clay (As found on TN).
This happens in a mixing chamber with one or more revolving shafts each with
blade extensions. Here after, the forming begins, there are basically 3 principal
processes of bricks clay bricks into their desired shape. These, will be discussed
later:
In this method, clay is not made sufficiently plastic, but only small amount of
water is mixed with clay as to form a damp powder. With plunger machines, this
powder is compressed in the mold, in the form of bricks. Such bricks are directly
burned, no drying is needed, but care is to be taken during burning where the
temperature should be raised gradually.
clay in its pigging chamber, sands or wets the molds, presses the clay into 4 to 9
molds at a time, strikes off the excess clay, bumps the molds uniformly and dumps
the bricks into a pallet. The pallets of bricks are carried away to the dryer as fast as
made.
1.4.3 Drying:
As wet clay bricks come from different brick machine, they contain from 7-50%
moisture depend on whether dry press stiff mud or soft mud process has been used
moisture in clay may be classified as:
i. Equilibrium moisture: is that moisture in the material which exerts a vapor
pressure equal to that exerted by the surrounding air of a given temperature and
humidity.
ii. Free moisture: is held strongly in the pore spaces.
Most of the free water is removed in the drying process and the remaining moisture
during the burning process. Mechanical dryer, who permit of automatic control of
temperature, humidity and air velocity, have come into general use. As the free
water of the clay body is removed, the clay particles tend to coalesce causing
shrinkage. The general effect of such shrinkage is to increase the resistance to
moisture flow in the dried layers. If the drying is carried on too rapidly as by means
of hot dry air, the moisture is removed from the surface of the solid more rapidly
than the interior of the solid so that the surface harden and cracking occur. It is
desirable to dry clay with moist air, reducing the drying rate to the point where
diffusion of water to the surface can keep up with the vaporization at the surface.
The average time necessary for drying clay brick is about 3 days, and the
temperature required is from 38 ºC to 149 ºC.
1.4.4 Burning:
The burning of clay in a kiln requires an average time of 3 to 4 days. The process of
burning may be divided into the following stages:
a. Water smoking:
During this period which remove most of the water in the clay under
temperature ranging from 125 ºC to 175 ºC.
b. Dehydration:
Dehydration consists of expelling chemically combined water by breaking
down the clay molecules. It begins at about 425 ºC and complete at about 750 ºC.
c. Oxidation:
Oxidation begins during the dehydration stage. All combustible matter is
consumed, carbon is eliminated, the fluxing materials are changed to oxides, and
sulfur is removed. This is achieved at about 300 – 900 ºC.
d. Vitrification: when extensive fluxing occurs and the mass becomes tight, solid
and nonabsorbent; leading to a deformed shape.
1.5. kilns
There are several different types of kiln but they can be allocated to two main
categories.
Intermittent kilns: These are static, usually small kilns and are used for firing
small batches of products eg. Special shapes.
Continuous kilns: For large scale production continuous kilns are more
economical and are capable of turning out large quantities of bricks at a steady
constant rate.
There are two main types of continuous kiln Chamber and Tunnel
1. Chamber kiln : In its simplest form a chamber kiln is an annular tunnel divided
off into chambers (usually 12-20). A section of the kiln (about 4-5 chambers) is
being fired at any one time. The firing is drawn round the kiln with chambers being
lit in front of the firing and the chambers behind are allowed to go out. Bricks are
loaded into the kiln in front of the fire and pre-heat for 1-2 days before the fire
reaches them. The bricks then fire for 2-3 days. Once the fire has passed, the bricks
cool before being removed from the kiln. They are then replaced with fresh dry
bricks awaiting the fire’s next circuit.
2. Tunnel kiln : In a tunnel kiln dry bricks are loaded onto a fireproof trolley or kiln
car. This then travels very slowly through the kiln. Typical schedule through the
kiln from end to end is 3-4 days but variations occur depending on production
schedules.
compression testing machine. The load shall be applied at a uniform rate until
failure occurs.
Plywood
1.7.3 Effloresce:
Efflorescence is a powdery deposit of salts which forms on the surface of bricks
and mortar. It is usually white but efflorescence can be yellow, green or brown. A
temporary efflorescence is particularly common on new brickwork as soluble salts
are transported to the surface of the brickwork by water.
Efflorescence can occur from a variety of sources. New bricks contain
minimal, if any, soluble salts, but mortar and concrete have relatively high soluble
salt contents. Ground waters that are naturally saltbearing can be drawn into base
brickwork. A faulty or bridged damp-proof course will allow the salts to migrate up
the wall. Render that has been applied over a damp-proof course can also allow salt
to migrate up the face of the brickwork. Water allowed to enter uncovered cavity
walls during construction is also likely to cause efflorescence, so brickwork must be
protected from water entry during construction.
Efflorescence on new brickwork may be unsightly, but it will not cause
damage unless it persists for a long time. Persistent efflorescence should be taken as
a warning that water is entering the wall through faulty copings, damp-proof
courses or pipes. If allowed to continue unchecked, the salts carried to the face of
the wall may eventually attack the bricks and cause deterioration.
Remedy: Laying dry bricks and providing good ventilation to speed up the drying
process after the bricks have been laid can minimise efflorescence. Forced
ventilation and heating of the premises may be necessary to ensure drying during
cold winter months. The best removal method is simply to brush off the deposit
with a stiff dry bristle brush after the wall has dried out.
Efflorescence on brickwork
Soluble salts, if present in bricks, will cause effloresce on the surface of bricks.
Effloresce test is carried out in accordance with Iraqi standard No. 24.The test is
very useful for comparing samples of bricks from different sources, such as when
we want to test bricks from several different factories at one time. In this test take a
representative sample of 10 bricks and place them on end in the pan containing
distilled water to a depth of 2.5 cm for 7 days. Allow the bricks to dry for 3 more
days in similar pan not containing water.
Water
2.5 cm
Pan
Colour: The brick should have a uniform deep red or cherry colour as
of the brick.
Textue and compactness: The surfaces should not be too smooth to cause
slipping of mortar. The brick should have precompact and uniform texture. A
fractured surface should not show fissures, holes grits or lumps of lime.
Hardness and soundness: The brick should be so hard that when scratched
by a finger nail no impression is made. When two bricks are struck together, a
Water absorption: should not exceed 20 per cent of its dry weight when kept
Brick earth: should be free from stones, kankars, organic matter, saltpetre,
etc.
A Slight 16 18 22 20
B Slight 11 13 26 24
C - 7 9 28 28