Nothing Special   »   [go: up one dir, main page]

UI-3271LE-M-GL (AB00907) : Sensor

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

UI-3271LE-M-GL (AB00907)

Not recommended for new designs


The camera model is no longer recommended for new application development.

uEye industrial cameras now also work with IDS peak! We recommend the Software Development Kit for the
implementation of new projects. Learn about the process here and switch now.
Please note: The technical data given here was measured using the IDS Software Suite.

Specification

Sensor
Sensor type CMOS Mono
Shutter Global Shutter
Sensor characteristic Linear
Readout mode Progressive scan
Pixel Class 3 MP
Resolution 3.17 Mpix
Resolution (h x v) 2056 x 1542 Pixel
Aspect ratio 4:3
ADC 12 bit
Color depth (camera) 12 bit
Optical sensor class 1/1.8''
Optical Size 7.093 mm x 5.320 mm
Optical sensor diagonal 8.87 mm (1/1.8")
Pixel size 3.45 µm
Manufacturer Sony
Sensor Model IMX265LLR-C
Gain (master/RGB) 24x/4x
AOI horizontal same frame rate
AOI vertical increased frame rate
AOI image width / step width 256 / 8
AOI image height / step width 2/2
AOI position grid (horizontal/vertical) 4/2
Binning horizontal -
Binning vertical increased frame rate
Binning method Mono
Binning factor 2
Subsampling horizontal same frame rate
Subsampling vertical increased frame rate
Subsampling method M/C automatic
Subsampling factor 2

Subject to technical modifications (2023-10-30)


Page 1 of 2 www.ids-imaging.com
IDS Imaging Development Systems GmbH
Dimbacher Str. 10 · 74182 Obersulm · Germany · Phone +49 7134 96196-0 · E-mail info@ids-imaging.com
UI-3271LE-M-GL (AB00907)

Model
Pixel clock range 10 MHz - 197 MHz
Frame rate freerun mode (in 8-bit mode) 57 fps
Frame rate trigger (continuous) 57 fps
Frame rate trigger (maximum) 57 fps
Exposure time (minimum - maximum) 0.024 ms - 1000 ms
Long exposure (maximum) 30000 ms
Power consumption 0.9 W - 1.7 W
Special features Overlap trigger
Sensor source gain

Ambient conditions
The temperature values given below refer to the outer device temperature of the camera housing.
For PCB versions, refer to the separate hints in the respective documentation.
Device temperature during operation 0 °C - 55 °C / 32 °F - 131 °F
Device temperature during storage -20 °C - 80 °C / -4 °F - 176 °F
Humidity (relative, non-condensing) 20 % - 80 %

Connectors
Interface connector USB Type-C
I/O connector 10-pin Molex connector (IllumiMate)
Power supply USB cable

Pin assignment I/O connector


1 Voltage output (USB Power Delivery), 5-15 V
2 Ground (GND)
3 General Purpose I/O (GPIO) 2, 3.3 V
4 General Purpose I/O (GPIO) 1, 3.3 V
5 TWI (Two Wire Interface) clock signal
6 TWI (Two Wire Interface) data signal
7 Trigger input without optocoupler 3.3 V
8 Flash output without optocoupler 3.3 V
9 Ground (GND)
10 Voltage output 3.3 V

Design
Lens Mount S-Mount
IP code -
Dimensions H/W/L 36.0 mm x 36.0 mm x 19.9 mm
Mass 16 g

Subject to technical modifications (2023-10-30)


Page 2 of 2 www.ids-imaging.com
IDS Imaging Development Systems GmbH
Dimbacher Str. 10 · 74182 Obersulm · Germany · Phone +49 7134 96196-0 · E-mail info@ids-imaging.com

You might also like