Nothing Special   »   [go: up one dir, main page]
Scribd Logo
Upload

Welcome to Scribd!

  • 37 views

    ADO A20F Quick Installation Guide

    Uploaded by

    Miguel Caldas

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    ADO A20F Quick Installation Guide

    Uploaded by

    Miguel Caldas
    37 views4 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    37 views4 pages

    ADO A20F Quick Installation Guide

    Uploaded by

    Miguel Caldas

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    ADO A16, A20, A20F, Ebike

    Quick Installation Guide


    English
    1 Accessories list
    1. Mobile Phone Stand 2. Pedals 3. Chargers 4. Foot support 5. Air Pump
    6. 5mm Hexagon screw driver 7. 6mm Hexagon screw driver 8.Multi-type wrench

    1 2 3 4 5 6 7 8

    2 Installation Guide
    Depending on the model, some steps have already been installed, just check it.
    1. After opening the carton, take out the accessories, tools 2. Unroll the body
    and bicycle.

    3. Close the body lock. 4. Fasten the safety lock

    5. Prepare foot brace, use the 6 tool to take out two 6. Place the foot brace behind the fender, use the 6 tool
    5mm hexagon screws locked in the foot brace. to lock the screws.
    7. Place the head tube into the front fork head tube 8. Straighten the head and make sure that the arrow on
    the label is aligned with the marking line. Make sure that
    the bicycle head and the body are vertical to each other.

    Mark lines

    9. Open the lock firstly.After alignment, put down the 10. Put the tube up, close the head lock, snap the safety
    tube, use the 7 tool to lock the screws. lock into the head lock

    2 1

    11. Open the handlebar lock, adjust the height of the head, 12. Open the cross handle lock, adjust the direction of the
    and then lock tightly. head grip, and then lock tightly.

    1
    2

    2
    1

    1. Align the left pedal ( with "L" mark ) to the crank thread
    and rotate the pedal counterclockwise.
    2. Align the right pedal ( with "R" mark ) to the crank
    13. Insert the saddle into the saddle tube. Adjust the height thread and rotate the pedal clockwise.
    of the saddle, and then lock tightly. 3. Tighten the pedals with an Hexagon screwdriver.

    4 3
    2
    1

    3
    15. Turn the headlight to the front 30 degrees down 16. Finish the installation, use the pump to inflate the
    position，use the 8 tool to twist the screws. tires.

    30°

    17. Before using the bicycle, insert the key and twist 18. Finished using the bicycle, turn the key 45°clockwise,
    45°counterclockwise, the battery has been started. the battery has been disconnected, and take out the key.

    45° 45°

    19.The step of removing battery, insert the key, press upward and then rotate 90°clockwise.

    Note:Remove the key firstly,and then take out key and then take out the battery to avoid damaging the key.

    2
    90°

    3 Operation Guide
    Battery power display Speed display

    SPEED
    Switch on/off Assist gear display
    km/h

    Assist gear
    adjustment km

    Multifunctional display area

    1.In shutdown state, long press Power key for 3 second to start the ebike;
    2.In the power on state, Long press Power key for 3 second to off the ebike;
    3.In the power-on state, press POWER KEY, the multi-function area will display ODO, VOL, TRIP, TIME.
    ODO: The total mileage of this bicycle when it is turned on
    VOL: Current battery voltage value display
    TRIP: Mileage traveled after this start
    TIME: The time since the start of this ride
    4. Press the “+” button to increase the gear. The higher the gear, the faster the speed.
    5. Press the “-” button to lower the gear. The lower the gear, the slower the speed.

    You might also like