Operating Instructions Process and Dialogue Module: Ecomatdisplay Cr1074
Operating Instructions Process and Dialogue Module: Ecomatdisplay Cr1074
Operating Instructions Process and Dialogue Module: Ecomatdisplay Cr1074
GB
Process and dialogue module
ecomatDisplay
CR1074
11433912 / 00 03 / 2022
CR1074
Contents
1 Preliminary note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Warnings used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1 Mounting accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.2 General installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.2.1 Location for mounting accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.2.2 Light sensor and status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3 Panel mounting / control cabinet installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3.1 Safety instructions for panel mounting / control cabinet installation . . . . . . . . . . . . . . 9
4.3.2 Installation with installation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.3 Panel cutout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.4 Mounting steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.4 Surface mounting with RAM® mount system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.4.1 Mounting steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.5 Other installation types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.1 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2 Connection accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.3 Connection technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.4 General wiring information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.5 Operating voltage and circuit breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.6 Shield connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.7 Ethernet interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.8 USB interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.8.1 Short-circuit protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.9 Selection of loudspeakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6 Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.2 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.3 Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.4 Required documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.5 Function of the internal temperature sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7 Maintenance, repair and disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.1 Battery change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.2 Cleaning the display surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.3 Cleaning the housing surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.4 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2
CR1074
1 Preliminary note
You will find instructions, technical data, approvals and further information using the QR code on the
unit / packaging or at www.ifm.com.
ATTENTION
Warning of damage to property
CAUTION
Warning of personal injury
w Slight reversible injuries may result.
WARNING
Warning of serious personal injury
w Death or serious irreversible injuries may result.
3
CR1074
2 Safety instructions
• The unit described is a subcomponent for integration into a system.
– The system architect is responsible for the safety of the system.
– The system architect undertakes to perform a risk assessment and to create documentation in
accordance with legal and normative requirements to be provided to the operator and user of
the system. This documentation must contain all necessary information and safety instructions
for the operator, the user and, if applicable, for any service personnel authorised by the
architect of the system.
• Read this document before setting up the product and keep it during the entire service life.
• The product must be suitable for the corresponding applications and environmental conditions
without any restrictions.
• Only use the product for its intended purpose (Ò Intended use).
• If the operating instructions or the technical data are not adhered to, personal injury and/or damage
to property may occur.
• The manufacturer assumes no liability or warranty for any consequences caused by tampering with
the product or incorrect use by the operator.
• Installation, electrical connection, set-up, programming, configuration, operation and maintenance
of the product must be carried out by personnel qualified and authorised for the respective activity.
• Protect units and cables against damage.
• Replace damaged units, otherwise the technical data and safety will be impaired.
• Observe applicable documents.
4
CR1074
3 Intended use
The ecomatDisplay process and dialogue module is a programmable graphic display for controlling,
parameter-setting and operation of mobile machines and plants. It is suited for use at an operating
altitude of 3000 m above sea level even under severe conditions, such as an extended temperature
range and mechanical stress (Technical data: www.ifm.com and indicated standards).
Permitted use:
• in mobile machines with supply from on-board systems (with battery) of 12 V DC or 24 V DC
nominal voltage
• in an industrial environment as a permanently installed unit with supply from SELV/PELV according
to the technical data
• even in wet environments
• even outdoors, if necessary with additional UV protection
Communication with other system components, such as decentralised I/O modules, takes place via
CAN, Ethernet and USB interfaces. Together with the Linux operating system they form a universal
platform for networking and communication with other CAN devices, networks or PCs.
By default, the device is not intended for direct connection to IT structures. If this application is
required, the users have to implement it (e.g. by using their own additional components).
This is a class A product. This product may cause radio interference in domestic areas.
u If required, take appropriate EMC screening measures.
The unit is not approved for safety-related tasks in the field of operator protection.
3.1 Properties
• 7" colour display
• Closed metal housing suitable for panel mounting and surface mounting outside or in the cabin
• Freely programmable to IEC 61131-3 with target visualisation
• 64-bit controller and Embedded Linux operating system
• CAN interfaces with CANopen and SAE J1939 protocol
• Ethernet and USB interfaces
Feature CR1074
Touch screen -
Freely programmable, backlit buttons 6
Navigation keys with button 1
Ethernet interfaces 1
CAN interfaces 2
ifm plug&play (CAN based) -
USB 2.0 interfaces 1
Analogue video inputs -
Digital inputs BL -
Digital outputs 2.5 A -
Line In -
Speaker output 1
Headphone output -
Controller Dual Core with GPU, 800 MHz
5
CR1074
Feature CR1074
RAM 1 GB
FLASH 2 GB
●= available
-= not available
6
CR1074
4 Installation
ATTENTION
Impact stress on display screen
w Damage possible
w Protection rating and electrical protection might be impaired
w Risk of injury possible
u If necessary, the system creator must take external measures to protect the device
depending on the requirements of the corresponding application.
u Replace damaged devices, otherwise the technical data and safety will be impaired.
On the back, the pressure compensation element, the service cover and the connector areas
are to be protected by taking external measures, if necessary.
7
CR1074
38,1
30
1 M5 2
1: 4 x M5 threaded hole for RAM® mount system / for the fixing profile of the installation kit
2: pressure compensation element
ATTENTION
The device is equipped with a pressure compensation element. Sealing or closing the
corresponding ventilation ducts with elastic materials may damage the device.
u Do not use any sealing materials in the area around the pressure compensation
elements.
1 2
1: light sensor
2: status LED
8
CR1074
The dimensions for the control panel cut-out are a basic prerequisite for the requirements
concerning electrical protection, fire protection and protection rating of the device / system.
However, this alone does not ensure compliance with the requirements. See the following
safety instructions. They must be complied with for the risk assessment by the system creator
(Ò Safety instructions).
WARNING
The housing does not meet the requirements concerning protective earth. Only functional
grounding is possible.
w Risk of electrical shock in case of hazardous active voltages in the control cabinet
behind the installation surface.
u The system creator must separate hazardous active voltages / parts behind the
installation surface from the housing of the device and its circuits by means of double /
reinforced insulation (air creepage distances, solid insulation).
u Take single-fault safety into account (e.g. individual core detached from the terminal →
use cable ties).
u The responsibility for the electrical protection of the system lies with the system creator.
When installing the device in a control cabinet, the following requirements concerning fire protection
apply:
If installed according to the information given in 4.3, the device itself complies with the requirements of
the IEC (or DIN EN) 61010-2-201 for a closed device to prevent fire from spreading.
WARNING
The damping strip (installation kit) has no flammability rating and thus presents no fire
obstacle.
w Fire protection for the system might not be given or might be restricted.
u The system creator has to ensure the fire protection depending on the requirements of
his/her application, if necessary by means of external precautions.
u The responsibility for the fire protection of the system lies with the system creator.
Using the installation kit does not ensure the protection rating of the system with the installed
device. The protection rating depends on the properties of the control panel / control cabinet
(e.g. thickness, material, surface characteristics, torsional stiffness).
CAUTION
The use of the installation kit does not ensure the requirements concerning the protection
rating of the system with the installed device.
w Protection rating and electrical protection might be impaired
u The system creator has to ensure the protection rating depending on the requirements of
his application, if necessary by means of external precautions.
u The responsibility for the protection of the system with the installed device lies with the
system creator.
9
CR1074
Fig. 1: Fixing profile of the installation kit Fig. 2: Dialogue module with mounted installation kit
Use the fixing profile of the mounting kit only together with a suitable spacer and the damping
strip .
4 x R7
213
10
CR1074
ATTENTION
Contact corrosion between the mounting screws and the housing.
w Damage to the device
u Do not use copper or nickel-plated materials for the bolting elements.
u Use zinc-plated screws.
u In very corrosive environments such as extremely salty air, use screws with surface
finishing on a zinc/nickel basis with thick-film passivation and sealing.
11
CR1074
A
1 2 3 4 5 6 7
Fig. 7: RAM® mount components Fig. 8: Dialogue module with mounted RAM® mount system
1: mounting arm with fastening screw
2: mounting plate with ball head
You will find more information about the available RAM® mount components at: www.ifm.com
12
CR1074
38 (1,5") 38,1
56
30
6
62 5,3
Fig. 9: Mounting plate with ball head Fig. 10: Hole dimensions
All other installation types are in the sole responsibility of the system creator.
13
CR1074
5 Electrical connection
u Disconnect the machine from the mains supply before installation; if necessary, also
disconnect any independently supplied input / output load circuits.
u Observe the national and international regulations for the installation of electrical equipment.
u Observe the requirements according to EN 60204.
Accessible surfaces of the device are insulated from the circuits with basic insulation to IEC 61010-1
(secondary circuit with max. 32 V DC, supplied from the mains circuit up to 300 V of overvoltage
category II).
GND of the supply is connected via EMC suppression capacitors on the shield connection (metal
housing) of the device.
The external wiring has to be carried out in a way that ensures the required separation from other
circuits.
5.1 Wiring
Wiring: Technical data: www.ifm.com
The terminals may only be supplied with the signals specified in the technical data or on the
device label
Unconnected pins must not be connected to the cable harness and its individual cores must be
sealed.
ATTENTION
Reverse polarity protection not ensured in case of power supply SELV/PELV on VBB30 and
VBB0)
Reverse polarity protection is only ensured in case of supply via the on-board system (via a
battery), if the polarity of the supply is reversed as a whole (battery connected incorrectly).
The basic principle of the reverse polarity protection is that the upstream fuses are quickly
switched off in case of excessive current. In case of supply via SELV/PELV, reverse polarity
protection is not ensured.
w Damage to the device possible
u Ensure that the ends of the cables are properly connected to the connector before
connecting the latter to the device, also in case of supply via the on-board system.
14
CR1074
u Carry out the fitting according to the indications of the cable manufacturer. The permitted maximum
is 10 Nm.
u During installation, place the M12 connector vertically so that the coupling nut will not damage the
thread.
u Unused sockets are equipped with protective caps (included).
Tightening torque: 1.3 ±0.1 Nm
u Use 40-pole connectors with individually sealed cores to ensure protection rating IP 67.
The ingress resistance of cables that users have cut to length must be guaranteed.
For CAN / IFM cables ≥ 30 m, ensure appropriate protection against surge (e. g. shielded
cables).
1 2
15
CR1074
ATTENTION
Wrong connection may cause damage to the device.
u Observe the safety instructions.
ATTENTION
The short-circuit / reverse polarity protection of the device applies to the operating voltage
connections. A short circuit between operating voltage VBB X and USB / audio might cause
damage to the device.
u Lay supply and signal cables away from the device using the shortest possible route.
u Provide all outgoing cables with a strain relief 200 mm behind the cable entry.
• USB ≤ 1.8 m
• Ethernet ≤ 30 m
• Audio ≤ 30 m
Minimum operating quality audio:
There might be interference to audio circuits in the vicinity of strong HF sources or due to ESD. This
may result in audible and visible distortion.
Required triggering
Designation Connector 1 Operating voltage Nominal value fuse
characteristics
VBB15 Pin 119 8...16 V DC and 16… 3A Tfuse ≤ 120 s at max.
32 V DC 6.25 A
Ignition-starter switch
VBB30 Pin 121 8...16 V DC 5A Tfuse ≤ 120 s at max.
6.25 A
16…32 V DC 3A Tfuse ≤ 120 s at max.
6.25 A
VBB0 Pin 114 8...16 V DC and 16… 15 A -
32 V DC
Digital inputs Pin 115, 116, 89, 97, 8...16 V DC and 16… 3A Tfuse ≤ 120 s at max.
110 32 V DC 6.25 A
Tab. 1: Terminal designation to DIN 72552
Supply cables of the inputs can be secured together with the circuit breaker for VBB15.
ATTENTION
Load dump and surge without connection of VBB0
w Destruction of the device possible!
u Always connect VBB0, even if the outputs are not used or are not available.
16
CR1074
u Establish the connection between the device and the ground of the vehicle using the intended
screw for RAM® Mount installation. If possible, use the thread next to the 40-pole AMP connector.
Max. tightening torque: 5 Nm
To avoid contact corrosion on the shield connection of the housing, do not use any copper or
nickel-plated materials for the bolting elements!
u In very corrosive environments such as extremely salty air, use screws with surface finishing on a
zinc/nickel basis with thick-film passivation and sealing.
The max. cable length depends, for example, on the bus topology, the selected operating mode
(10/100 Mbits/s) or the quality of the connectors.
u Use screened connector housings and connect the screen of the Ethernet cable to the connector
housing.
u Do not lay the Ethernet cable in parallel to live cables.
17
CR1074
≤ 1,8 m
ATTENTION
The USB interface (M12 connector) is not protected against short circuits with a live wire
outside the following voltage ranges:
+5 V DC -0.3...6.0 V DC (pin 1)
–Data -0.3...3.6 V DC (pin 2)
+Data -0.3...3.6 V DC (pin 3)
ID -0.3...3.6 V DC (pin 4)
w A short circuit will destroy the USB interface.
18
CR1074
6 Set-up
6.1 General
The factory setting of the device shows a demo application. The installed recovery app can be used to
load any suitable firmware version to the device.
Factory setting:
IP address 192.168.82.247
Subnet mask: 255.255.255.0
Gateway IP address: 192.168.82.1
The user is responsible for the safe function of the application programs which he created
himself. If necessary, they must additionally carry out an approval by corresponding supervisory
and test organisations according to the national regulations.
6.3 Set-up
The set-up allows setting the device parameters directly via the local display or the web interface of
the device. Select the set-up button in the App Launcher to start the local set-up.
While the App Launcher is shown, entering the device IP address (e.g. 192.168.82.247) via the
connected web browser takes you to the web set-up.
After leaving the set-up, a project can be loaded. Libraries (.lib) are available to use the operating
elements, interfaces and other internal functions of the device. They have to be integrated into the
application program.
19
CR1074
ATTENTION
Internal temperature exceeds the permissible value (Technical data: www.ifm.com)
w Malfunction or damage to the device possible
u Reduce device temperature.
u Take appropriate measures to prevent further heating up of the device.
20
CR1074
Battery may explode if handled incorrectly. Do not recharge or disassemble the battery, nor
dispose of it in fire.
1 2
1: service cover
2: battery
u Replace the battery if the displayed time is permanently wrong after the device is switched on.
ATTENTION
The protection rating does not apply if the service cover is open and there is no ESD
protection of the accessible contacts inside
w Damage to the device possible
u Clean the area around the service cover before opening it.
u Remove the service cover on the back of the device (width across flats 13 mm or ¼“).
u Protect inside of device, sealing areas and sealing of the service cover from soiling and
humidity.
u When changing the battery, take ESD precautions.
u Remove the battery and replace it with a new one.
Observe the polarity: positive side up
Battery type (Technical data: www.ifm.com)
u Check sealing areas and sealing for soiling. Clean them, if necessary.
u Screw the service cover with 3.0 Nm to restore the protection rating (width across flats
13 or ¼“).
u Reset the system time via device set-up or application
(see programming manual ecomatDisplay).
21
CR1074
• Chemicals dissolving plastics such as methylated spirit, benzine, thinner, alcohol, acetone or
ammonia.
• paper towels, crepe paper etc.
• abrasive cleaners etc.
• polish or wax
u Clean the device from dirt using a soft, chemically untreated and dry cloth.
u In case of severe soiling, use a damp cloth.
7.4 Repair
u The device must only be repaired by the manufacturer.
Observe the safety instructions. Ò Safety instructions
7.5 Disposal
u Dispose of used batteries in accordance with the national environmental regulations.
Do not dispose of used batteries as household waste.
u Dispose of the unit in accordance with the national environmental regulations.
22