Service Manual: CDP-CX57
Service Manual: CDP-CX57
Service Manual: CDP-CX57
SERVICE MANUAL
US Model Canadian Model AEP Model UK Model E Model Australian Model
Model Name Using Similar Mechanism CDP-CX50/CX571 CD Mechanism Type Base Unit Type Optical Pick-up Type CDM-46C1 KSM-213BFN/M-NP KSS-213B/S-N
SPECIFICATIONS
Compact disc player Laser Laser output Semiconductor laser ( = 780 nm) Emission duration: continuous Max 44.6 W* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up block with 7 mm aperture. 20 Hz to 20 kHz 1dB More than 107 dB More than 88 dB Less than 0.013% Mass (approx.) Channel separation Outputs Jack type LINE OUT DIGITAL OUT (OPTICAL) Phono Jacks Maximum output level Load impedance More than 100 dB Supplied accessories Audio cord (2 phono plugs 2 phono plugs) (1) CONTROL A1 cord (supplied for Canadian models only) (1) Remote commander (remote) (1) Sony SUM-3 (NS) batteries (2) CD booklet holder (1) and Label (1) Design and specifications are subject to change without notice. 5.5 kg (12 lbs 3 oz) General Power requirements Where purchased US/Canada Australia UK Other countries Power consumption Dimensions (approx.) (w/h/d) Power requirements 120 V AC, 60 Hz 240 V AC, 50/60 Hz 220 V 230 V AC, 50/60 Hz 110 V 120 V or 220 V 240 V AC, adjustable, 50/60 Hz 12 W When the front cover is closed 430 182.5 295 mm (17 7 1/4 11 5/8 in.) incl. projecting parts When the front cover is open 430 182.5 414 mm (17 7 1/4 16 3/8 in.) incl. projecting parts
MICROFILM
MODEL
7. DIAGRAMS ................................................................. 7-1. Block Diagrams BD Section .................................................................... Main Section ................................................................. 7-2. Printed Wiring Board BD Section ........................... 7-3. Schematic Diagram BD Section ............................... 7-4. Printed Wiring Board Audio Section ....................... 7-5. Schematic Diagram Audio Section .......................... 7-6. Printed Wiring Board Main Section ........................ 7-7. Schematic Diagram Main Section ........................... 7-8. Printed Wiring Boards Panel Section ...................... 7-9. Schematic Diagram Panel Section .......................... 7-10. Printed Wiring Boards Sensor/Motor Section ......... 7-11. Schematic Diagram Sensor/Motor Section ............. 7-12. IC Pin Function Description ........................................... 8. 9.
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. The laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. (Except for the customers in the United States and Canada) The following caution label is located inside the unit.
CAUTION : INVISIBLE LASER RADIATION WHEN INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
OPEN AND
ADVARSEL :
USYNLIG LASERSTRLING VED BNING NR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDG UDSAETTELSE FOR STRLING. UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEFFNET UND SICHEREITSVERRIEGELUNG BERBRCKT. NICHT DEM STRAHL AUSSETZEN.
VORSICHT : VARO !
: AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NKYMTTMLLE LASERSTEILYLLE. L KATSO STEESEEN. : OSYNLING LASERSTRLING NR DENNA DEL R PPNAD OCH SPRREN R URKOPPLAD. BETRAKTA EJ STRLEN.
USYNLIG LASERSTRLING NR DEKSEL PNES OG SIKKERHEDSLS BRYTES. UNNG EKSPONERING FOR STRLEN.
VARNING
ADVERSEL : VIGYAZAT ! :
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The limit indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal Parts on Set
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the S curve check in CD section adjustment and check that the S curve waveform is output repeatedly.
0.15 F
1.5 k
AC voltmeter (0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY.
NOTE : The contents of Track No. 1 to 41 are the same as those of the current TEST DISC-their titles are displayed.
Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is no a fault.) TRACK No. 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 to 99
Recorded Contents ! # $%& ( )* + , . / 01234567 89 : ; <=>? @A B C D E F G H I J K L MNO P Q R S T U VW XYZ [ ] ^ _ (21h to 27h)1kHz 0dB L&R (28h to 2Fh) (30h to 37Fh) (38h to 3Fh) (40h to 47Fh) (48h to 4Fh) (50h to 57Fh) (58h to 5Fh) (60h to 67Fh) (68h to 6Fh) (70h to 77Fh) (78h to 7Fh) (A0h to A7h) 8859-1 (A8h to AFh) (B0h to B7h) (B8h to BFh) (C0h to C7Fh) (C8h to CFh) (D0h to D7Fh) (D8h to DFh) (E0h to E7h) (E8h to EFh) (F0h to F7Fh) (F8h to FFFh) N All the same N All the same N All the same N All the same N All the same N All the same
Display
ab c de f g
a b c d e f g (60h to 67h)
h i j k l mn o pq r s t u vw x y z { I } ~ C
1 2
N All the same p q r s t u v w (70h to 77h) xy z { } ~ (78 (A0 is not displayed (A8 C P R are not displayed
2 3
1 4
i PR
3
1 4
1 2 3 4
(B0 (B8
1
(C0h to C7h) N All the same D (D0h to D7h) Y (D8 (E0h to E7h) N All the same (F0h to F7h) y (F8h to FFh) N All the same N All the same to N All the same
SECTION 2 GENERAL
LOCATION OF PARTS AND CONTROLS
Front Panel
STANDBY
TIME/TEXT
DISC/CHARACTER
1/u
PUSH OPEN
INPUT
MEMO SEARCH
@
PLAY MODE REPEAT GROUP FILE 1 2 GROUP 3 4 5
PUSH ENTER
FADER
CHECK
CLEAR
1 2 3 4 5 6 7 8 9 ! ! !
I/u (power switch) button Front cover PLAY MODE button REPEAT button GROUP FILE button Display window GROUP 1-5 buttons TIME/TEXT button INPUT button MEMO SEARCH button JOG dial (DISC/CHARACTER/PUSH ENTER knob) FADER button
! ! ! ! ! ! ! @ @ @ @
CHECK button CLEAR button button button p button P button button PLUS ONE button X-FADE button NO DELAY button MEGA CONTROL button
SECTION 3 DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
2 case
7 claw
8 front panel
5 wire (flat type) (19 core) (CN503) 7 claw 6 three screws (BVTT3 6)
TABLE (50)
3 bracket (ILLUMINATION)
4 screw (PTPWH2.6 8)
1 screw (BVTT3 6)
5 table (50)
3 two screws (BVTP3 8) 4 ring (B) 9 screw (P3 14) 0 connector (CN51) 0 connector (CN52) 9 screw (BVTT3 8) ! connector (CN61)
7 wire (flat type) (9 core) (CN103) 5 screw (BVTT3 6) 6 connector (CN54) 1 screw (BVTT3 6) ! base (CDM)
6 transformer cover 2 ring (A) 8 two screws (BVTT3 6) ! connector (CN201) ! AUDIO board 7 screw (BVTT3 6)
BASE UNIT
1 two screws (BTP2.6 8) 2 bracket 3 screw (BTP2.6 10) 4 reinforcement (small)
7 base unit
4 BD board
2 sled shaft
1 claw
10
FLUORESCENT INDICATOR TUBE, LED ALL LIT, AND KEY CHECK MODE
1. Short-circuit the test point (TP ADJ) and test point (TP AFADJ) of the MAIN board with a lead wire. 2. Insert the power plug into the outlet. The whole fluorescent indicator tube lights up. When the SRAM is faulty, SRAMNG will be displayed. 3. Pressing the I/u button sets the key check mode. All buttons have individual button numbers. When a button is pressed, the button number is counted up and displayed.
1 DISCS CD1 DISC
**
Count up display
**
Displays button number
Display of special functions in ADJ mode Observation mode during S When this mode is set, the below will be displayed. *1
*1
ALL DISCS CD1
S-JI mode
Automatic eccentricity measurement (Not used for servicing) When this mode is set, the below will be displayed.The Sokuteichu count down display will be counted down from 4 to to 1 *2.After counting down, the eccentricity value will be displayed *3.
I/u
X-FADE NO DELAY GROUP 5 GROUP 4 GROUP 3
*2
ALL DISCS CD1 DISC TRACK MIN NEXT DISC SEC
GROUP 2 GROUP 1 GROUP FILE PUSH OPEN (DOOR SW ON) PUSH OPEN (DOOR SW OFF)
Sokuteichu -4
Sokuteichu count down display
*3
ALL DISCS CD1
STANDBY LED ON All lit (LED lights up) Partially lit 1 (LED lights up) Partially lit 2 LED lights up Partially lit 3 (LED lights up) Partially lit 4 Each time JOG is rotated, GROUP FILE 1 2 3 4 5 is displayed on the fluorescent indicator tube, and 1, 2, 3, 4, 5 light up one by one, and GROUP LED 1, 2, 3, 4, 5 lights up one by one. Clockwise : GROUP FILE 1n2n3n4n5 Counterclockwise : GROUP FILE 5n4n3n2n1
Henshin 021
Eccentricity value
11
Partially lit 1
1 DISCS
AGING MODE
G A B C D E F
CD1
Partially lit 2
1 DISCS CD1
Mode which repeatedly changes and plays back discs automatically in the unit. It will repeat aging as long as no errors occur. If an error occurs during aging, it will stop all servos, motors, etc. instantaneously, display the error number, and stop operations. However, the stopping conditions differ according to whether the unit is equipped with the self-protection function during errors described later. The function serves to maintain the state of the unit when errors occur. Sequence of Aging Mode Order of Disc Change (1 cycle takes 3 minutes) $ 1. No. 51 $ 2. No. 20 $ 3. No. 40 $ 4. No. 30 $ 5. No. 10 $ 6. No. 40* $
Partially lit 3
1 DISCS CD1 2nd
**
Partially lit 4
1 DISCS CD1 GROUP FILE 1
$ 1. Disc change $ 2. Load in $ 3. TOC read $ 4. Access of last track $ 5. 3 second playback $ 6. Access of first track $ 7. 3 second playback $ 8. Load out $ *
**
FLUORESCENT INDICATOR TUBE AND LED CHECK MODE
This mode is set by pressing the I/u button while pressing the [CHECK] and [PLUSONE] buttons in order in the power-off (standby) state. The whole fluorescent indicator tube lights up, and the [STANDBY], [MEGACONTROL] , [GROUP1-5] , [PLUSONE] , and P LEDs light up. This mode can be exited by pressing the I/u button.
SHIPMENT MODE (Set to this mode when returning the unit to the user.)
This mode is set by pressing the I/u button while pressing the [PUSHENTER] and [PLUSONE] buttons in order in the poweroff (standby) state. The power goes off automatically after the SRAM is all-erased and the BD is opened (loading out state). Test points and connecting points: [MAIN BOARD] CONDUCTOR SIDE
TP (GND) R505 TP (AFADJ) R504 TP (ADJ) IC501
DISC No. 40 chucks twice during one cycle. To differentiate, the [2nd] on the block indicator of the fluo rescent indicator tube will light up during the second chucking.
Special Functions in Aging Mode There are some useful function in the aging mode. Disc setting mode*1 Switching of use/disuse of protection function in errors *2 Aging cycle count function *3 *1 Disc setting mode: 5 discs are set before setting the aging mode. This mode makes the setting of these discs more easy. *2 Switching of use/disuse of protection function in errors: Function which voluntarily corrects errors which occur during normal operations by retries. If this function is not provided, all operations will be stopped without retiring. It is suitable for checking errors with low reproducibility. If this function is provided, and errors can be corrected by retries, aging will be continued without stopping. (The normal aging should be performed with be.)
IC201
CN704
CN702
12
Error Display *3 Aging cycle count function: Functions which displays the number of agings carried out on the Fluorescent indicator tube in numbers. One aging cycle Aging carried consists of six discs.
(Hexadecimal)
1 DISCS CD1 DISC
1 1Err*01
Error code
40
Disc number
51
Disc number
1
Track number
1 0.02
MIN
SEC
Without remote commander for aging mode: 1. Turn ON the power of the unit. Open the front cover. 2. Press the [PLAYMODE], , and buttons in order. 3. When the disc set mode is set, the and P LEDs blink. The following procedure is the same as in the case With remote commander for aging mode.
Aging procedure: Some operating method will be changed depending on if the following jig for the aging mode exists or not. Jig Parts. No J-2501-123-A
With remote commander for aging mode: 1. Turn ON the power of the unit. Open the front cover. 2. Press the [AGINGSTART] button of the remote commander for aging mode. 3. When the disc set mode is set, the and P LEDs blink. 4. Rotate the JOG dial. The slits (No. 10, 20, 30, 40, 51) for setting the discs will come forward. Insert the discs into these slits. Do not set the discs in other slits. 5. Set the use/disuse of the self protection function in errors. Press the [REPEAT] button. When REPEAT is displayed on the fluorescent indicator tube, the self protection function during the error will become Use. If the REPEAT display is OFF, it means that the function is not used. (Normally set to Use when performing aging.) 6. Press the button. 7. The LED blinks, the aging mode is set, and aging is started. 8. The aging cycle lasts 3 minutes. When problems occur during aging, the error number will be displayed on the fluorescent indicator tube, and the P LED will light up. (Refer to the following table for the details of the errors.) 9. Aging will be repeated as long as no errors occur. 10. After each aging cycle, the number displayed on the Fluorescent indicator tube will increase. 11. To end aging, press the I/u button Error code
Code number Err 01 Err 02 Err 03 Err 04 Err 05 Err 06 Err *1 Err *2 Err *3 Err *4 Err *5 Err *6 Table operation check 2 Loading operation check 1 Loading operation check 2 BU related check 1 BU related check 2 BU related check 3 BU related check 4 BU related check 5 BU related check 6 Name DISC sensor check 1 DISC sensor check 2 No disc in the specified slit Disc in other slits No function No table sensor input Load in timeover Load out timeover Access timeover High speed search NG Q data read error BU operation (From focus search to until signal can be read) timeover GFS monitor error Focus cannot be imposed by focus search Contents
The * numbers mean the following according to the state of the unit during aging 2 : From checking to end of TOC read 3 : From end of TOC read to end of last track playback 4 : From end of last track playback to end of first track playback
13
oscilloscope
3. While pressing the [CLEAR] and [PLUSONE] buttons at the same time and turn ON the power.
CHECK button
CLEAR button
I/u button
button
button
4. The fluorescent indicator tube shows as follows, and the mechanism section adjustment mode is set.
Lit according to rotational direction DISC No.
ALL DISCS CD1 DISC SEC
51 3.7
PLUS ONE
**
Blinks
5. The disc table rotates in the clockwise direction. The disc table rotation time is displayed with PLUS ONE slit as a measuring point. 6. Press the [CLEAR] button, to be rotated the disc table counterclockwise. 7. Measure the waveform of the oscilloscope when the disc table is rotating.
14
8. Move the holder (sensor) center so that the flat portion center at the top of the D.SENS (CH1) input waveform and the H center of HHOUT (CH2) coincide.
Fixed screw
Holder (sensor)
9. Tighten the fixed screw to fix the disc table, then press the [CLEAR] button. 10. The disc table rotates in the clockwise direction. Measure the waveform and make sure that the flat portion center at the top of the D.SENS (CH1) input waveform and the H center of HHOUT (CH2) conform. Note: During the adjustment mode, the rotational direction is switched each time the [CLEAR] button is pressed. Pressing the [CHECK] button enters the loading mode which will be described later. Pressing the [CLEAR] button rotates the disc table again. Contets of the fluorescent indicator tube's display in the loading mode
51 IN OFF
ON
Loading direction
Loading IN SW condition
15
Magnet holder
Disc Disc
Disc holder A
a b a=b
16
11. Turn OFF the power, and remove the lead wire connected at step 7.
Note : A clear RF signal waveform means that the shape can be clearly distinguished at the center of the waveform.
RF signal waveform
S Curve Check
oscilloscope BD board TP (FE) TP (VC) +
Procedure : 1. Press the I/u button and turn ON the power supply. 2. Open the front cover, and press the [PLUSONE] button. 3. Set the disc (YEDS-18) into the PLUS ONE slit. 4. Close the front cover, and chuck the disc. 5. Press the I/u button and turn OFF the power. 6. Connect the oscilloscope to TP (FE) of the BD board. 7. Connect TP (ADJ) of the MAIN board and connect TP (GND) with a lead wire. 8. Press the I/u button and turn ON the power. 9. The first track will be played back automatically. When the [CHECK] button is pressed, S-JI mode will be displayed on the fluorescent indicator tube, and focus search will be repeated. 10. Check the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 1.8 0.6 Vp-p.
S-curve waveform symmetry
E-F Balance (Traverse) Check The procedure for this checking method differs for when a general remote control unit is used and not used.
oscilloscope BD board TP (TE) TP (VC) +
When a general remote commander is used: 1. Press the I/u button and turn ON the power supply. 2. Open the front cover, and press the [PLUSONE] button. 3. Set the disc (YEDS-18) into the PLUS ONE slit. 4. Close the front cover, and chuck the disc. 5. Press the I/u button and turn OFF the power. 6. Connect the oscilloscope to TP (TE) of the BD board. 7. Connect TP (ADJ) of the MAIN board and connect TP (GND) with a lead wire. 8. Press the I/u button and turn ON the power. 9. Playback the fifth track of the disc. 10. Press the [3] button on the remote commander. (The tracking servo and the sledding servo are turned OFF.) 11. Check the level B of the oscilliscope's waveform and the A (DC voltage) of the center of the Traverse waveform. Confirm the following : A/B x 100 = less than 10%
Traverse waveform B 0V A (DC voltage) Center of the waveform
11. Turn OFF the power, and remove the lead wire connected at step 7.
Note : Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. Take sweep time as long as possible and light up the brightness to obtain best waveform.
RF Level Check
oscilloscope (AC range) BD board TP (RF) TP (VC) +
12. Press the [8] button on the remote control unit. (The tracking servo and sledding servo are turned ON.) Confirm the C (DC voltage) is almost equal to the A (DC voltage) is step 11.
Traverse waveform
Procedure : 1. Press the I/u button and turn ON the power supply. 2. Open the front cover, and press the [PLUSONE] button. 3. Set the disc (YEDS-18) into the PLUS ONE slit. 4. Close the front cover, and chuck the disc. 5. Press the I/u button and turn OFF the power. 6. Connect the oscilloscope to TP (RF) of the BD board. 7. Connect TP (ADJ) of the MAIN board and connect TP (GND) with a lead wire. 8. Press the I/u button and turn ON the power. 9. Playback the fifth track of the disc. 10. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not.
C (DC voltage)
13. Turn OFF the power, and remove the lead wire connected at step 7.
17
When a general remote commander is not used: 1. Solder lead wires to TP (DVDD) and TP (TOFF) on the BD board severally. 2. Connect the oscilloscope to TP (TE) of the BD board. 3. Press the I/u button and turn ON the power supply. 4. Open the front cover, and press the [PLUSONE] button. 5. Set the disc (YEDS-18) into the PLUS ONE slit. 6. Close the front cover, and chuck the disc. 7. Playback the fifth track of the disc. 8. Short-circuit the lead wire connected at step 1. (The tracking servo is turned OFF) 9. Check the level B of the oscilliscope's waveform and the A (DC voltage) of the center of the Traverse waveform. Confirm the following : A/B x 100 = less than 10%
Traverse waveform Center of the waveform B 0V A (DC voltage)
RF PLL Free-run Frequency Check Procedure : 1. Connect the frequency counter to TP (PCK) of the BD board.
BD board TP (PCK) frequency counter
2. 3. 4. 5. 6. 7.
Press the I/u button and turn ON the power supply. Open the front cover, and press the [PLUSONE] button. Set the disc (YEDS-18) into the PLUS ONE slit. Close the front cover, and chuck the disc. Playback th e fifth track of the disc. Confirm that reading on frequency counter is 4.3218 MHz 30 kHz.
About RV601 on the MAIN board RV601 of the MAIN board requires no adjustments. Please note that it should be dixed to mechanical center position when you moved and do not know origin position.
10. Disconnect the lead wire short-circuited at step 8. (The tracking servo is turned ON.) Confirm the C (DC voltage) is almost equal to the A (DC voltage) is step 8.
Traverse waveform
C (DC voltage)
11. Turn OFF the power, and remove the lead wire connected at step 1.
18
TP (FE)
TP (TE)
IC201
IC201
CN704
CN702
CN702
CN704
19
SECTION 7 DIAGRAMS
Circuit Boards Location
TABLE SENSOR board LED board DISC SENSOR (R) board DISC SENSOR (S) board
MAIN board
POWER SW board
20
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) Note on Schematic Diagram: All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. : internal component. C : panel designation. Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Note: Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice por tant le numro spcifi. Note on Printed Wiring Boards: X : parts extracted from the component side. Y : parts extracted from the conductor side. : internal component. b : Pattern from the side which enables seeing. : Solder bridge. Indication of transistor.
87654321 87654321 87654321 87654321
U : B+ Line. V : B Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark: PLAY Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. J : CD c : digital out Abbreviation AED : North European AUS : Australian model. CND : Canadian model. E2 : 120 V AC Area in E model. E3 : 240 V AC Area in E model. SP : Singapore model.
21
Waveforms BD Section
1 IC101 $ (RFSM) (PLAY MODE) 6 IC102 ^ (16M)
1.8
6.2 Vp-p
16 MHz
2 IC101 @ (FE) (PLAY MODE) 7 IC102 ^ (4.2M)
560 mVp-p
5.4 Vp-p
4.2 MHz
3 IC101 7 (TE) (PLAY MODE)
MAIN Section
1 IC501 # (XTAL)
460 mVp-p
4.4 Vp-p
10 MHz
4 IC102 @ (PCK)
DIAPLAY Section
1 IC901 % (OSC0)
6.2 Vp-p
2.3 Vp-p
230 ns
5 IC102 $ (XOUT)
480 ns
3.6 Vp-p
16.9344 MHz
22
CDP-CX57
SL+
DETECTOR E
B+
B
(Page 25)
A A B D C D C B F
1 4 2 5 10 6
RCHO 40 LCHO 37
10 EFMIN
DIGITAL SIGNAL PROCESSOR, CLV SERVO PROSESSOR, DIGITAL FILTER, D/A CONVERTER IC102
LD PD LASER DIODE
62 LDD 63 LDS CV+ 40 CV 39 SLOF 38 HFL 37 TES 36 TOFF 35 TGL 34 JP+ 33 JP 32 12 CLV+ 13 CLV 14 V/P 15 HFL 16 17 18 19 20 TES TOFF TGL JP+ JP
FOCUS COIL
TRACKING COIL T+ 19 20 TRACKING COIL DRIVE FOCUS/TRACKING COIL DRIVE IC103 (1/2) F F+ 17 18 FOCUS COIL DRIVE 22 15 TO
T 2-AXIS DEVICE
A
(Page 25)
27 CONT4 27
CONT3
SPD
15
16 FD
58
10
29 SLD
SL 30 SL+ 31
RES
5 6
RST
23
24
CDP-CX57
MAIN SECTION
LINE AMP, LOW-PASS FILTER IC301,401
LOUT
MIX AMP IC302 R-CH R-CH MUTING Q331 POWER ON MUTING Q301 R-CH MUTING Q302 MUTING Q303 R-CH MUTING CONTROL SWITCH Q304 MUTING CONTROL SWITCH Q382
L R L R
A0 | A14
S-RAM IC502 WE D0 | D7
CE 20
D304
10-13, 25-23, 21,2,26,1 MUTING CONTROL SWITCH Q383 LOADING/TABLE MOTOR DRIVE IC601 LDOUT 15 LDIN 14 TBLL 16 TBLR 17 3 2 16 17 LOADING MOTOR DRIVE TABLE MOTOR DRIVE 8 9 10 11 M61 LOADING MOTOR M62 TABLE MOTOR DISC TABLE FLAG SENSOR IC52 63 T.SENS2 DISC TABLE HOME POSITION SENSOR IC53 64 T.SENS3
27 11-13,15-19
A
(Page 24) RST MUTEL
WE
28 DIGITAL OUT OPTICAL IC701 RESET 5 SIGNAL GENERATOR 2 IC201(1/2) RESET SWITCH Q501 ZMUTE
65 DOWNSW
DOUT
29 ICSW
RESET CD1/2/3 43
13
75-77,68-71 D0 | D7
30
XMODE SCLK SRDT DQSY RWC WRQ DRF COIN SQOUT CQCK SL+ SL
B
(Page 24)
61 51 52 60 58 55 54 50 49 48 47 59
XMODE SCLK SRDT DQSY RWC WRQ DRF COIN SQOUT CQCK SL+ SL
BUSOUT 45
EXTAL 31 DOORSW D.SENS HHOUT RMIN JOG1 JOG2 KEY0 KEY1 KEY2 KEY3 LEDL FLCK FLDT FLLT XTAL 32
TGL
57 TGL
22
26
27
21
20
42 1 2 3
25 CLOSE OPEN
23 24
38 39 40 41
61 CS(FLLT) 60 RESET
62 CP(FLCK)
1 3 JOG 5 1 KEY MATRIX S901-S924 REMOTE CONTROL RECEIVER IC902 FL901 VF1 VF2
39-4
40
41-55
P1 | P36
AC IN
30V
RECT D205
BUFFER Q901 DISC SENSOR Q51 DISC SENSOR D51 +5V (FOR BD) QI | QG, QD, QC QJ | QN
60 1G
59-45 2G | 16G
17-13
18-20,23,24
63 VF2 65
12.4V
D841-D843
+5V
D901-903, 909-911 05
25
26
CDP-CX57
7-2. PRINTED WIRING BOARD BD Section See page 20 for Circuit Boards Location. See page 21 for Note.
Semiconductor Location
Ref. No. D151 IC101 IC102 IC103 IC104 Q101 Q102 Q103 Location D-1 D-3 B-3 B-1 B-2 B-4 B-4 E-1
(Page 35)
(Page 36)
27
28
CDP-CX57
7-3. SCHEMATIC DIAGRAM BD Section See page 22 for Waveforms. See page 46 for IC Block Diagrams. See page 49 for IC Pin Function Description. See page 21 for Note.
(Page 38)
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
29
30
CDP-CX57
7-4. PRINTED WIRING BOARD AUDIO Section See page 20 for Circuit Boards Location. See page 21 for Note.
(Page 35)
(Page 36)
Semiconductor Location
Ref. No. D201 D202 D203 D204 D205 D701 IC301 IC302 IC401 IC402 Location C-5 C-5 C-5 D-5 B-5 A-7 B-8 B-7 C-7 C-6 Ref. No. IC701 Q301 Q302 Q303 Q331 Q401 Q402 Q403 Q431 Q701 Location A-8 B-7 B-7 A-6 C-7 B-6 B-7 B-6 C-7 A-7
(Page 44)
(Page 36)
31
32
CDP-CX57
7-5. SCHEMATIC DIAGRAM AUDIO Section See page 21 for Note.
(Page 45)
(Page 38)
(Page 38)
(Page 38)
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
33
34
CDP-CX57
7-6. PRINTED WIRING BOARD MAIN Section See page 20 for Circuit Boards Location. See page 21 for Note.
Semiconductor Location
Ref. No. D206 D207 D210 D211 D212 D304 D382 D404 D501 IC201 IC202 IC203 IC501 IC502 IC601 Q201 Q304 Q305 Q380 Q381 Q382 Q383 Q404 Q405 Q481 Q501 Q502 Location E-2 D-2 C-1 C-1 C-1 E-1 D-1 E-1 C-4 C-2 B-1 A-4 B-4 D-4 E-4 E-2 E-1 A-1 C-1 D-1 D-1 E-1 E-1 B-1 C-1 D-3 D-3
(Page 28)
(Page 28)
(Page 44)
(Page 39)
(Page 43)
(Page 43)
35
36
CDP-CX57
7-7. SCHEMATIC DIAGRAM MAIN Section See page 22 for Waveform. See page 47 for IC Block Diagrams. See page 53 for IC Pin Function Description. See page 21 for Note.
(Page 45)
(Page 41)
(Page 30)
(Page 30)
(Page 45)
(Page 33)
37
38
CDP-CX57
7-8. PRINTED WIRING BOARDS PANEL Section See page 20 for Circuit Boards Location. See page 21 for Note.
(Page 36)
(Page 40)
(Page 39)
39
40
CDP-CX57
7-9. SCHEMATIC DIAGRAM PANEL Section See page 22 for Waveform. See page 48 for IC Block Diagram. See page 21 for Note.
(Page 38)
41
42
7-10. PRINTED WIRING BOARDS SENSOR/MOTOR Section See page 20 for Circuit Boards Location. See page 21 for Note.
(Page 36)
(Page 36)
(Page 35)
43
(Page 36)
(Page 31)
44
CDP-CX57
(Page 37)
(Page 38)
(Page 37)
(Page 37)
(Page 33)
45
64
63 62 APC
61
60 RF DET
59
58
57 REF
56
55 54 53 52 51 50
49 48 47
NC TBC FSC DGND SLI SLC RFSRFSM CV+ CVSLOF HFL TES TOFF TGL JP+
FIN2 FINI E F TB
1 2 3 4 5 6 7 I/V BAL
VCA
46 45 LSC +44 43 42 +-
VCA
-COM INTERFACE
+ -
8 9 10 11 12 -+ 13 14
+-
+ TO FD 15 16 17 18
FDFA
SPSPD
SLEQ
SLD
FEAGND
FA-
SPI
IC102
LC78622E
TEST1 RES COCK COIN SQOUT TEST1 TEST5 SBCK SFSY RWC WRQ FSX 4.2M 16M PW CS
63
62
61
60
SPG
59 58 57 56 55 54 53 52
SLSL+
SP
JP-
FE
DEFI
TAI PDO
2 3
VVSS ISET VVDD FR VSS EFMO EFMIN TEST2 CLV+ CLVV/P HFL TES
CONT4 CONT5
EMPH
CF2
DOUT
46
TEST3
+19
+-
+ -
20
21 22 23 24 25 26 27
28 29
30 31 32
51
50
49
2K x 8BIT RAM MUTE RAM ADDRESS GENERATOR DIGITAL ATTENUATOR OVERSAMPLING DIGITAL FILTER 1BIT DAC L.P.F 43 42 41 40 39 38 37 36 35 34 33 XVDD MUTER RVDD RCHO RVSS LVSS LCHO LVDD MUTEL N.C TEST4
IC103
LA6541
IC104
LC89170M
VDD
VCC MUTE
1 2
24 23
VCC VREF
EXCK 1
CPU INTERFACE
14 VDD
VINL VGL
3 4
11k
LEVEL SHIFT
LEVEL SHIFT
11k
22 21
VIN4 VG4
13 DQSY
SCOR 3
BTL DRIVER BTL DRIVER 20 19 Vcc VO8 VO7
12 SRDT
VO1 VO2
5 6
WFCK 4
11 SCLK
MCK 5
XMODE 6
+
10 SW2
9 SW1
GND 7 8 TEST
7 8 9 10 11k
BTL DRIVER
BTL DRIVER
18 17 16
LEVEL SHIFT
LEVEL SHIFT
11k
15
11 1 12 REGULATOR RESET
14 13
CD RES
V IN
1 ERROR AMP
AMP
V REF AMP 3 VO
VOMUTE 7
CDEL
RESET GEN
2 EN
6 VID
5 VOD
GND
RES CN
5 6
V OUT
47
IC601
BA6780
VIN1
18
VIN2
VCC
FIN1
17
FIN2
RIN1
16
RIN2
IOUT
VEE
VEE
15
CT2
VREF
14 VEE
VREG
13
FBIN-
VCC
12
FBIN+
COVERNER OUTPUT
OUT1+
8 9
11 OUT2+ 10 OUT2-
+ -
OUT1-
M66310FP
QM QD QG QH QE QL QF QJ QI QN QK
24
23
22
21
20
19
18
17
16
15
14
13
0 D
CK
0 R D
CK
0 R D
CK
0 R D
CK
0 R D
CK
0 R D
CK
0 R D
CK
0 R D
CK
0 R D
CK
0 R D
CK
0 R D
CK
0 R D
CK
1 D
CK
1 R D
CK
1 R D
CK
1 R D
CK
1 R D
CK
1 R D
CK
1 R D
CK
1 R D
CK
1 R D
CK
1 R D
CK
1 R D
CK
1 R D
CK
D D 1 CK R D 1 CK R 1
CK
D 1
CK
D 0
CK
D 0
CK
D 0
CK
D 0
CK
1
QA
2
QB
3
VCC
4
DATA
5
OE
6
LT
7
RST
8
CLK
9
GND
10
SQP
11
QO
12
QP
48
7-12.
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
49
Pin No. 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Pin Name CV+ RFSM RFS SLC SLI DGND FSC TBC NC DEF CLK CL DAT CE DRF FSS VCC2 REFI VR LF2 PH1 BH1 LDD LDS VCC1
I/O I O I O I O I O I I I I O I I O I I I O I
Function CLV error signal input from the DSP (IC102) Playback EFM RF signal output to the DSP (IC102) Works together with the RFSM (pin $) to set the RF gain and the 3T compensation constant for the EFM RF signal SLI (Slice Level Control) is output to control a data slice level of the RF waveform by the DSP (IC102) Input terminal for controlling a data slice level by the DSP (IC102) Ground terminal (digital system) Focus search smoothing capacitor output terminal TBC (Tracking Balance Control) sets a EF balance variable range Not used (open) Defect detection signal output to the DSP (IC102) Reference clock (4.2336 MHz) input from the DSP (IC102) Command serial clock signal input from the system controller (IC501) Command serial data input from the system controller (IC501) Command chip enable signal input from the system controller (IC501) Focus OK signal output to the system controller (IC501) L: NG, H: OK FSS (Focus Search Select) is a switching terminal for the focus search mode (search/+search for a reference voltage) Not used (open) Power supply terminal (+5V) (servo system and digital system) Connected to the coupling capacitor for the reference voltage (+2.5V) Reference voltage (+2.5V) output terminal Constant setting for a disc defect detection Connected to the capacitor for the RF signal peak hold Connected to the capacitor for the RF signal bottom hold Laser drive signal output to the automatic power control circuit Light amount monitor input of the laser diode (PD) Power supply terminal (+5V) (RF system)
50
BD BOARD IC102 LC78622E (DIGITAL SIGNAL PROCESSOR, DIGITAL FILTER, D/A CONVERTER)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
Pin Name DEFI TAI PDO VVSS ISET VVDD FR VSS EFMO EFMIN TEST2 CLV+ CLV V/P HFL TES TOFF TGL JP+ JP PCK FSEQ VDD CONT1 CONT2 CONT3 CONT4 CONT5 EMPH C2F DOUT TEST3 TEST4 NC MUTEL LVDD LCHO LVSS RVSS RCHO RVDD
I/O I I O I I O I I O O O I I O O O O O O I I O I O O O O I I O O O
Function Defect detection signal input from the RF amplifier (IC101) PLL test input terminal Not used (fixed at L) PLL phase comparison output for external VCO control Ground terminal (internal VCO system) Connected to a current adjusting resistor for the PDO output Power supply terminal (+5V) (internal VCO system) Adjusts the VCO frequency range Ground terminal (digital system) Slice level control to EFM signal output Playback EFM RF signal input from the RF amplifier (IC101) Test input terminal (fixed at L in this set) Disc motor control signal output to the RF amplifier (IC101) (3-value output available depending on the command) Sled servo on/off control signal output to the RF amplifier (IC101) Rough servo/phase control automatic switching monitor output H: rough servo, L: phase servo Tracking detection signal input from the RF amplifier (IC101) (Schmitt input) HFL (High Frequency Level) is used to determine whether the main beam is positioned on a pit or mirror Tracking error signal input from the RF amplifier (IC101) (schmitt input) Tracking off control signal output to the RF amplifier (IC101) Tracking becomes off when TOFF is H Tracking gain control signal output to the RF amplifier (IC101) (Raises gain when L) Track jump control signal output to the RF amplifier (IC101) (3-value output available depending on the command) EFM data playback clock monitor output terminal (4.3218 MHz when phase is locked) Sync signal detection output terminal (H when a sync signal detected from the EFM signal and that generated internally coincide) Power supply terminal (+5V) (digital system) Guard frame sync input terminal Sled servo on/off control signal input terminal Sled servo drive control signal output terminal Sled limit-in detect switch (S101) input terminal The optical pick-up is inner position when L Not used (open) De-emphasis control signal output terminal The de-emphasis disc is being played back when H Not used (open) C2PO (error condition monitor) signal output terminal Digital signal output terminal (EIAJ format) Test input terminal (fixed at L in this set) Test input terminal (fixed at L in this set) Not used (open) Line muting on/off control signal output terminal (for L-ch side) H: muting on Power supply terminal (+5V) (L-ch D/A converter system) Analog audio signal output from the internal D/A converter block (for L-ch side) Ground terminal (L-ch D/A converter system) Ground terminal (R-ch D/A converter system) Analog audio signal output from the internal D/A converter block (for R-ch side) Power supply terminal (+5V) (R-ch D/A converter system)
51
Pin No. 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Pin Name MUTER XVDD XOUT XIN XVSS SBSY EFLG PW SFSY SBCK FSX WRQ RWC SQOUT COIN CQCK RES TEST11 16M 4.2M TEST5 CS TEST1
I/O O O I O O O O I O O I O I I I O O O I I I
Function Line muting on/off control signal output terminal (for R-ch side) H: muting on Power supply terminal (+5V) (crystal oscillator system) System clock output terminal (16.9344 MHz) System clock input terminal (16.9344 MHz) Ground terminal (crystal oscillator system) C1, C2, single correction, and double correction monitor output to the CD text decoder (IC104) Subcode P to W output terminal Subcode frame sync signal output to the CD text decoder (IC104) Write frame clock signal output to the CD text decoder (IC104) Subcode reading clock signal input from the CD text decoder (IC104) (schmitt input) 7.35 kHz sync signal output divided from the crystal oscillation Subcode Q synchronizing signal output to the system controller (IC501) Command chip enable signal input from the system controller (IC501) (schmitt input) Subcode Q data output to the system controller (IC501) Command serial data input from the system controller (IC501) Command serial clock signal input from the system controller (IC501) (schmitt input) Fetching clock input or subcode extracting clock input from SQOUT (pin %) System reset signal input from the reset signal generator (IC201) L: reset For several hundreds msec. after the power supply rises, L is input, then it changes to H Test output terminal Not used (open)
Master clock signal (16.9344 MHz) output to the CD text decoder (IC104) Reference clock signal (4.2336 MHz) output to the RF amplifier (IC102) Test input terminal (fixed at L in this set) Chip select signal input terminal Not used (fixed at L) Test input terminal (fixed at L in this set)
52
Pin Name A3 to A7 A12 A14 A11 to A8 A13 WE LDIN LDOUT TBLL TBLR NC HHOUT LEDL FLLT JOG1 JOG2 DOORSW FLCK FLDT ZMUTE ICSW RESET EXTAL XTAL VSS TX TEX AVSS AVREF KEY0 KEY1 KEY2 KEY3 D.SENS CD1/2/3 TEST BUSOUT BUSIN SL+ CQCK
I/O O O O O O O O O O O O O O O I I I O O O O I I O O I I I I I I I I I O I O O
Function
Data write enable signal output to the static RAM (IC502) L active Loading motor drive signal (load-in direction) output to the BA6780 (IC601) H active Loading motor drive signal (load-out direction) output to the BA6780 (IC601) H active Table motor drive signal (counterclockwise) output to the BA6780 (IC601) H active Table motor drive signal (clockwise) output to the BA6780 (IC601) H active Not used (open) AND output of T.SENS1 (pin ^) and T.SENS2 (pin ^) when the test mode Serial data latch pulse output to the LED driver (IC903) H active Serial data latch pulse output to the FL driver (IC901) L active Jog dial pulse input from the rotary encoder (RE901) Jog dial pulse input from the rotary encoder (RE901) Door open/close detect switch (S925) input L: close, H: open Serial data transfer clock signal output to the FL driver (IC901) L active Serial data output to the FL driver (IC901) Muting on/off control signal output for the 2nd CD IN H active Enable signal output to the LA5602 (IC201) Used for the BD section reset H active System reset signal input from the reset signal generator (IC203) L: reset For several hundreds msec. after the power supply rises, L is input, then it changes to H Main system clock input terminal (10 MHz) Main system clock output terminal (10 MHz) Ground terminal Sub system clock output terminal Not used (open) Sub system clock input terminal Not used (fixed at L) Ground terminal (for A/D converter) Reference voltage (+5V) input terminal (for A/D converter) Key input terminal (A/D input) CLEAR, CHECK, FADER, MEMO SEARCH, INPUT, TIME/TEXT keys input (S901 to 906) Key input terminal (A/D input) , , p, P, , PLUS ONE, REPEAT, PLAY MODE keys input (S907 to 914) Key input terminal (A/D input) I/u, X-FADE, NO DELAY, MEGA CONTROL keys input (S921 to 924) Key input terminal (A/D input) GROUP 5 to 1, GROUP FILE keys input (S915 to 920) Inputs the disc sensor (Q51) detection signal H active COMMAND MODE switch (S701) input terminal L: CD1, H: CD3 (CD2: center voltage input) Setting terminal for the test mode L: ADJ mode, center voltage: AFADJ mode Sircs remote control signal output for the S-LINK CONTROL A1 H active Sircs remote control signal input for the S-LINK CONTROL A1 L active Sled feeding signal (external direction) output to the RF amplifier (IC101) H active Command serial clock signal output to the RF amplifier (IC101) and DSP (IC102) L active
53
Pin No. 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 to 71 72 73 74 75 to 77 78 to 80
Pin Name SQOUT COIN SCLK SRDT NC DRF WRQ RMIN TGL RWC SL DQSY XMODE T.SENS1 T.SENS2 T.SENS3 DOWNSW UPSW SELECT D3 to D6 VDD NC (VDD) D7 D0 to D2 A0 to A2
Function Subcode Q data input from the DSP (IC102) Command serial data output to the RF amplifier (IC101) and DSP (IC102) Serial data transfer clock signal output to the CD text decoder (IC104) L active Serial data input from the CD text decoder (IC104) Not used (open) Focus OK signal input from the RF amplifier (IC101) and DSP (IC102) L: NG, H: OK Subcode Q synchronizing signal input from the DSP (IC102) H active Remote control signal input from the remote control receiver (IC902) L active Tracking gain control signal input from the DSP (IC102) Gain becomes low when tracking gain is H Command latch output to the RF amplifier (IC101) and DSP (IC102) L active Sled feeding signal (internal direction) output to the RF amplifier (IC101) H active Serial data synchronizing signal input from the CD text decoder (IC104) L active Reset signal output to the CD text decoder (IC104) H: reset Disc table flag detect sensor (IC51) input terminal Disc table flag detect sensor (IC52) input terminal Disc table home position detect sensor (IC53) input terminal Inputs the loading out switch (S52) detection signal L active Inputs the loading in switch (S51) detection signal L active Not used (fixed at H) Two-way data bus with the static RAM (IC502) Power supply terminal (+5V) Not used (connected to power supply (+5V) line) Two-way data bus with the static RAM (IC502) Two-way data bus with the static RAM (IC502) Address signal output to the static RAM (IC502)
54
2
#1
not supplied
2
#1
not supplied
3
#1
4
#1
#1
Ref. No. * 1 2 * 3
Part No.
Description
Remark
Ref. No. 4 5
Part No.
Description
Remark
55
62
not supplied
73 72 58 57 59 60
61
62 62
75 63 65 62
55 53 52 51 54 69 54
#2 #1 #2
64
56 67 75 74
66
71
70 69
62
68
Ref. No. 51 52 53 54 * 55 56 57 58 59 60 * 61 62 63
Part No. 4-997-019-01 4-997-020-01 4-997-018-01 4-988-675-01 4-988-674-01 4-989-312-01 3-008-600-01 4-997-062-11 4-991-156-01 4-991-152-11
Description LID (F) WINDOW (LID) LID (R) CUSHION (STOPPER) CUSHION (CLOSE) LATCH, NS EMBLEM (5-AR), SONY PANEL, FRONT INDICATOR (POWER) BUTTON (POWER)
Remark
Ref. No. 64 65 * 66 67 * 68 69 70 71 72 73 74 75
Part No. X-4949-357-1 4-996-359-11 A-4724-009-A 1-773-140-11 4-978-398-21 3-354-963-21 4-987-955-22 4-987-941-01 4-987-778-01 4-991-153-01
Description BUTTON (MAIN) ASSY BUTTON (BLOCK) DISPLAY BOARD, COMPLETE WIRE (FLAT TYPE) (19 CORE) CUSHION DAMPER WINDOW (FL) KNOB (JOG) BUTTON (MEGA-CON) BUTTON (2 GANG)
Remark
1-668-578-11 POWER SW BOARD 4-951-620-01 SCREW (2.6X8), +BVTP 4-933-134-61 SCREW (+PTPWH M2.6X6)
56
103
104
US, CND UK E
109
AEP, AED, SP
AUS
108
#3 #3
108
108
108
108
107 120
#1
115
102
#4 #5
101
#1
106 105
#1 #1
110
121
T501 #1 #3 #6
112
111
116
#1 #1
114 115
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Remark Ref. No. ! 109 110 110 111 112 113 114 115 116 117 Part No. 1-569-007-11 3-703-571-11 4-966-267-11 1-782-465-11 4-990-029-01 X-4946-543-2 4-978-398-21 4-990-895-01 3-704-198-51 4-988-534-01 1-769-921-11 3-704-198-61 A-4724-007-A A-4724-012-A A-4724-015-A Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi. Remark
Ref. No. 101 102 103 104 * 105 * 105 * 105 * 106 * 107 * 107 * * * * * 107 107 107 107 107
Description HOLDER, TABLE RING (A) TABLE (50) SCREW PTP WH (2.6X8) (DIA. 10) AUDIO BOARD, COMPLETE (E)
Description
ADAPTOR, CONVERSION 2P (E) BUSHING (S) (FBS002), CORD (E) BUSHING (FBS001), CORD (EXCEPT E) WIRE (FLAT TYPE) (16 CORE) RING (B) FOOT (SMALL) ASSY CUSHION SUPPORT (P TYPE), LSR SUPPORT, PC COVER, MOTOR WIRE (FLAT TYPE) (9 CORE) SUPPORT, PC MAIN BOARD, COMPLETE (E) MAIN BOARD, COMPLETE (US, CND) MAIN BOARD, COMPLETE (AEP, UK, AED, SP, AUS)
A-4724-011-A AUDIO BOARD, COMPLETE (US, CND) A-4724-014-A AUDIO BOARD, COMPLETE (AEP, UK, AED, SP, AUS) 4-991-167-11 COVER, TRANSFORMER 4-997-568-01 PANEL, BACK (US) 4-997-568-11 PANEL, BACK (CND) 4-997-568-21 4-997-568-31 4-997-568-41 4-997-568-51 4-997-568-61 1-558-943-41 1-575-651-21 1-590-926-11 1-696-845-11 1-751-529-11 PANEL, BACK (AEP, AED) PANEL, BACK (UK) PANEL, BACK (AUS) PANEL, BACK (E) PANEL, BACK (SP) CORD, POWER (E) CORD, POWER (AEP, AED, SP) CORD, POWER (US, CND) CORD, POWER (AUS) CORD, POWER (UK)
* * * *
1-431-333-11 TRANSFORMER, POWER (US, CND) 1-431-334-11 TRANSFORMER, POWER (AEP, UK, AED, SP, AUS) 1-431-335-11 TRANSFORMER, POWER (E)
57
321
324
316 326
not supplied
318
326
#8 #2 #8 #2
307 306
320
#9
312
not supplied
329 301
Ref. No. * 301 * 302 303 304 305 * 306 307 308 309 310 * 311 312 313 * 314 * 315 Part No. 1-663-975-11 4-988-427-01 4-988-420-01 4-988-436-01 4-988-418-01 4-988-417-01 4-988-433-01 X-4948-020-1 4-988-438-01 4-988-437-01 4-988-416-01 4-988-419-01 4-992-069-01 4-988-454-01 4-988-421-01 Description
303
Remark
Ref. No. 316 317 318 * 319 320 321 322 * 323 324 325 326 327 328 329
Part No. A-4672-522-A 4-960-633-11 4-999-139-01 4-976-473-01 4-988-431-01 X-4948-019-1 1-777-874-11 1-663-973-11 4-988-440-01 4-988-441-01 4-957-577-21 4-992-413-02 3-910-095-11 4-951-620-01
Description MAGNET ASSY YOKE (MAGNET) PULLEY (B) HOLDER (LED-S) ROLLER (DISC) HOLDER ASSY, BU WIRE (FLAT TYPE) (16 CORE) DISC SENSOR (S) BOARD SPRING (F-1), TENSION SPRING (F-2), TENSION SCREW PTP WH (2.6X8) (DIA. 10) STOPPER RUBBER, VIBRATION PROOF SCREW (2.6X8), +BVTP
Remark
SW BOARD COVER, CAM SLIDER (LOADING) SPRING (LOADING), TORSION HOLDER (A), DISC SLIDER (CAM) SLIDER (LOCK) LEVER (LOADING) ASSY SPRING (LEVER), TENSION SPRING (HOLDER), TORSION BASE, LOADING HOLDER (B), DISC SCREW (+PTPWH) (M2) (DIA. 7) COVER (LEVER) HOLDER (MAGNET)
58
352
358
355
356
#10 #11
360
M62
357
M61
359
#3
Description TABLE SENSOR BOARD BELT GEAR (A) (LOADING) PULLEY GEAR (TABLE)
Remark
Description BASE (CDM) DISC SENSOR (R) BOARD MOTOR BOARD HOLDER (SENSOR) MOTOR ASSY (LOADING)
Remark
59
not supplied
409 406
406
406
404 403
401
408
#13
402
M102 M101
406
405
407
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
Description OPTICAL PICK-UP KSS-213B/S-N GEAR (A) (S) GEAR (B) (RP) SHAFT, SLED BD BOARD, COMPLETE
Remark
Description
Remark
SCREW (M2), +PSW WIRE (FLAT YTPE) (16 CORE) TURN TABLE ASSY (AU) F T, T CHASSIS ASSY (MG) (F) (SPINDLE) MOTOR GEAR ASSY (MB) (RP) (SLED)
60
AUDIO
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifis par une marque ! sont critiquens pour la scurit. Ne les remplacer que par une pice portant le numro spcifi. When indicating parts by reference number, please include the board.
Ref. No. * * *
Part No.
Description
Remark
Part No.
Description
Remark
A-4724-008-A AUDIO BOARD, COMPLETE (E) A-4724-011-A AUDIO BOARD, COMPLETE (US, CND) A-4724-014-A AUDIO BOARD, COMPLETE (AEP, UK, AED, SP, AUS) ********************* < CAPACITOR > C203 C206 C231 C232 C301 C302 C303 C304 C305 C331 C401 C402 C403 C404 C405 C431 C701 C702 C704 C708 1-161-494-00 1-126-968-11 1-126-768-11 1-126-768-11 1-130-482-00 1-106-343-00 1-126-967-11 1-162-290-31 1-124-282-00 1-126-965-11 1-130-482-00 1-106-343-00 1-126-967-11 1-162-290-31 1-124-282-00 1-126-965-11 1-104-665-11 1-161-494-00 1-162-282-31 1-161-494-00 CERAMIC ELECT ELECT ELECT MYLAR MYLAR ELECT CERAMIC ELECT ELECT MYLAR MYLAR ELECT CERAMIC ELECT ELECT ELECT CERAMIC CERAMIC CERAMIC < CONNECTOR > 0.022uF 100uF 2200uF 2200uF 0.0082uF 1000PF 47uF 470PF 22uF 22uF 0.0082uF 1000PF 47uF 470PF 22uF 22uF 100uF 0.022uF 100PF 0.022uF 25V 50V 16V 16V 50V 200V 10V 50V 25V 50V 50V 200V 10V 50V 25V 50V 10V 25V 50V 25V
IC IC IC IC IC
20% 20% 20% 5% 5% 20% 10% 20% 20% 5% 5% 20% 10% 20% 20% 20% 10%
< JACK > J301 J701 1-770-720-11 JACK, PIN 4P (2ND CD IN, LINE OUT) 1-774-726-11 JACK (S-LINK CONTROL A1) < LINE FILTER > ! L201 1-424-485-11 FILTER, LINE < TRANSISTOR > Q301 Q302 Q303 Q331 Q401 Q402 Q403 Q431 Q701 8-729-141-26 8-729-141-26 8-729-141-26 8-729-141-26 8-729-141-26 8-729-141-26 8-729-141-26 8-729-141-26 8-729-620-05 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR < RESISTOR > R301 R302 R303 R304 R305 R306 R307 R308 R309 R310 R311 R312 R313 R314 1-249-417-11 1-249-429-11 1-249-432-11 1-247-836-11 1-247-836-11 1-249-428-11 1-247-826-00 1-249-429-11 1-249-429-11 1-249-429-11 1-247-887-00 1-247-826-00 1-249-409-11 1-249-421-11 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON 1K 10K 18K 1.6K 1.6K 8.2K 620 10K 10K 10K 220K 620 220 2.2K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 2SC3622A-LK 2SC3622A-LK 2SC3622A-LK 2SC3622A-LK 2SC3622A-LK 2SC3622A-LK 2SC3622A-LK 2SC3622A-LK 2SC2603-EF
1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P 1-766-955-11 CONNECTOR, BOARD TO BOARD 11P 1-778-981-11 CONNECTOR, BOARD TO BOARD 13P < GROUND TERMINAL BOARD >
CP2
61
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
AUDIO
Ref. No. R316 R318 R319 R321 R331 R332 R335 R401 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R416 R418 R419 R421 R431 R432 R435 R701 R702 R703 R704
BD
Description 8.2K 470K 2.2K 2.2K 1.8K 2.2K 470K 1K 10K 18K 1.6K 1.6K 8.2K 620 10K 10K 10K 220K 620 220 2.2K 8.2K 470K 2.2K 2.2K 1.8K 2.2K 470K 10K 4.7K 10K 10 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W Ref. No. C110 C111 C112 C113 C114 C115 C116 C117 C118 C119 C120 C121 C122 C123 C124 C125 C126 C127 C128 C129 C130 C131 C132 C133 C141 C142 C151 C152 C153 C154 C155 C156 C157 C158 C159 C160 C161 C162 C163 C164 C165 C166 C167 C171 C172 C173 C174 C175 C181 C182 C183 C184 Part No. Description 0.022uF 0.033uF 0.001uF 0.15uF 0.15uF 0.01uF 0.01uF 220PF 0.47uF 0.22uF 22uF 0.0033uF 4.7uF 0.1uF 10uF 100uF 100uF 0.033uF 0.047uF 0.33uF 100uF 0.001uF 0.1uF 0.1uF 0.1uF 2.2uF 0.1uF 0.1uF 0.1uF 0.001uF 10PF 2PF 0.01uF 0.1uF 22PF 100PF 0.1uF 0.1uF 0.1uF 10PF 10PF 220uF 0.1uF 0.1uF 100uF 47uF 0.1uF 0.1uF 47uF 47uF 330PF 330PF 10% 10% 10% 10% 10% Remark 25V 25V 50V 16V 16V 50V 50V 50V 16V 16V 16V 50V 50V 25V 16V 10V 10V 25V 25V 16V 10V 50V 25V 25V 25V 16V 16V 16V 16V 50V 50V 50V 50V 25V 50V 50V 25V 25V 25V 50V 50V 10V 25V 25V 10V 16V 25V 25V 16V 16V 50V 50V 1-163-037-11 CERAMIC CHIP 1-163-989-11 1-163-009-11 1-164-492-11 1-164-492-11 1-164-232-11 1-164-232-11 1-163-001-11 1-107-823-11 1-164-489-11 1-124-234-00 1-164-182-11 1-126-963-11 1-163-038-00 1-104-396-11 1-126-177-11 1-126-177-11 1-163-989-11 1-163-809-11 1-110-501-11 1-124-443-00 1-163-009-11 1-163-038-00 1-163-038-00 1-163-038-00 1-164-505-11 1-107-725-11 1-107-725-11 1-107-725-11 1-163-009-11 1-163-227-11 1-163-085-00 1-164-232-11 1-163-038-00 1-163-101-00 1-163-117-00 1-163-038-00 1-163-038-00 1-163-038-00 1-163-227-11 1-163-227-11 1-104-666-11 1-163-038-00 1-163-038-00 1-124-443-00 1-124-589-11 1-163-038-00 1-163-038-00 1-104-664-11 1-104-664-11 1-163-003-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP
Part No.
1-249-428-11 CARBON 1-247-895-00 1-249-421-11 1-249-421-11 1-249-420-11 1-249-421-11 1-247-895-00 1-249-417-11 1-249-429-11 1-249-432-11 1-247-836-11 1-247-836-11 1-249-428-11 1-247-826-00 1-249-429-11 1-249-429-11 1-249-429-11 1-247-887-00 1-247-826-00 1-249-409-11 1-249-421-11 1-249-428-11 1-247-895-00 1-249-421-11 1-249-421-11 1-249-420-11 1-249-421-11 1-247-895-00 1-249-429-11 1-249-425-11 1-249-429-11 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON
10% 10% 10% 20% 10% 20% 20% 20% 20% 10% 10% 10% 20% 10%
! S201 S701
1-572-675-11 SWITCH, POWER VOLTAGE CHANGE (VOLTAGE SELECTOR) (E) 1-571-308-11 SWITCH, SLIDE (COMMAND MODE) < TRANSFORMER >
5% 5%
! T501 ! T501
1-431-333-11 TRANSFORMER, POWER (US, CND) 1-431-334-11 TRANSFORMER, POWER (AEP, AED, UK, SP, AUS) ! T501 1-431-335-11 TRANSFORMER, POWER (E) ************************************************************ * A-4724-006-A BD BOARD, COMPLETE ****************** < CAPACITOR > C101 C102 C103 C104 C105 C106 C107 C108 C109 1-163-038-00 1-163-038-00 1-164-489-11 1-163-003-11 1-163-023-00 1-110-501-11 1-163-989-11 1-164-492-11 1-164-161-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.22uF 330PF 0.015uF 0.33uF 0.033uF 0.15uF 0.0022uF 25V 25V 16V 50V 50V 16V 25V 16V 100V
20% 20%
1-770-173-11 CONNECTOR, FFC/FPC 16P 1-691-894-21 SOCKET, CONNECTOR 16P 1-568-852-11 SOCKET, CONNECTOR 9P Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
62
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
BD
Ref. No. Part No. Description < DIODE > D151 8-719-991-33 DIODE 1SS133T-77 < IC > IC101 IC102 IC103 IC104 8-759-498-93 8-759-449-65 8-759-449-66 8-759-428-57 IC IC IC IC LA9241M LC78622E LA6541 LC89170M R136 R137 R138 R151 R152 R153 R154 R155 R156 R157 R158 R159 R160 R161 R162 R163 R164 R165 R166 R171 R172 R173 R174 R181 R182 R183 R184 R191 R192 R193 R194 R195 R196 R197 1-216-073-00 1-216-009-00 1-216-089-00 1-216-045-00 1-216-093-00 1-216-051-00 1-216-085-00 1-216-089-00 1-216-081-00 1-216-077-00 1-216-049-11 1-216-083-00 1-216-037-00 1-216-073-00 1-216-037-00 1-216-049-11 1-216-065-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-057-00 1-216-057-00 1-216-073-00 1-216-073-00 1-216-025-00 1-216-041-00 1-216-041-00 1-216-025-00 1-216-041-00 1-216-025-00 1-216-025-00 Remark Ref. No. R132 R133 R134 R135 Part No. 1-216-065-00 1-216-113-00 1-216-113-00 1-216-065-00 Description
RES, CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP RES, CHIP RES, CHIP RES, CHIP RES, CHIP RES, CHIP RES, CHIP RES, CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP RES, CHIP RES, CHIP < SWITCH >
< JUMPER RESISTOR > JW1 JW2 JW4 JW5 JW6 JW7 JW8 JW9 JW10 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 0 0 0 0
< TRANSISTOR > Q101 Q102 Q103 8-729-119-78 TRANSISTOR 2SC403SP-51 8-729-119-78 TRANSISTOR 2SC403SP-51 8-729-119-76 TRANSISTOR 2SA1175-HFE < RESISTOR > R101 R102 R103 R104 R105 R106 R107 R108 R109 R110 R111 R112 R113 R114 R115 R116 R117 R118 R119 R120 R121 R122 R123 R124 R125 R126 R127 R128 R129 R130 R131 1-216-097-00 1-216-093-00 1-216-093-00 1-216-093-00 1-216-093-00 1-216-097-00 1-216-097-00 1-216-068-00 1-216-076-00 1-216-093-00 1-216-057-00 1-216-109-00 1-216-099-00 1-216-055-00 1-216-689-11 1-216-057-00 1-216-085-00 1-216-081-00 1-216-069-00 1-216-085-00 1-216-059-00 1-216-083-00 1-216-099-00 1-216-093-00 1-216-089-00 1-216-037-00 1-216-089-00 1-216-077-00 1-216-069-00 1-216-113-00 RES, CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP RES, CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP METAL CHIP 100K 68K 68K 68K 68K 100K 100K 6.2K 13K 68K 2.2K 330K 120K 1.8K 39K 2.2K 33K 22K 6.8K 33K 2.7K 27K 120K 68K 47K 330 47K 15K 6.8K 470K 470K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
S101
X101 1-577-576-21 VIBRATOR, CRYSTAL (16.9344MHz) ************************************************************ * 1-663-972-11 DISC SENSOR (R) BOARD ********************* 4-990-669-01 HOLDER (SENSOR) 7-685-132-19 SCREW +BTP 2.6X5 TYPE2 N-S < TRANSISTOR > Q51 8-729-926-31 PHOTO TRANSISTOR PT483F1S ************************************************************
63
DISPLAY
Remark Ref. No. R903 R904 R905 R906 R907 R908 R909 R910 R911 R912 R913 R914 R915 R916 R917 R918 R930 R931 R932 R933 R934 R936 R937 R938 R941 R942 R943 R944 R945 Part No. Description 1.5K 2.2K 3.3K 6.8K 680 1K 1.5K 2.2K 3.3K 6.8K 15K 680 1K 1.5K 2.2K 3.3K 3.3K 1K 1K 1K 1K 100K 100 100 220 220 220 220 1K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1-249-419-11 CARBON 1-249-421-11 CARBON 1-247-843-11 CARBON 1-249-427-11 1-249-415-11 1-249-417-11 1-249-419-11 1-249-421-11 1-247-843-11 1-249-427-11 1-249-431-11 1-249-415-11 1-249-417-11 1-249-419-11 1-249-421-11 1-247-843-11 1-247-843-11 1-249-417-11 1-249-417-11 1-249-417-11 1-249-417-11 1-249-441-11 1-247-807-31 1-247-807-31 1-249-409-11 1-249-409-11 1-249-409-11 1-249-409-11 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON
1-663-973-11 DISC SENSOR (S) BOARD ********************* 4-976-473-01 HOLDER (LED-S) < CONNECTOR >
* CN53
D51
R54 1-249-409-11 CARBON 220 5% 1/4W ************************************************************ * A-4724-009-A DISPLAY BOARD, COMPLETE *********************** 4-996-361-01 HOLDER (FL) < CAPACITOR > C901 C902 C903 C904 C905 1-164-159-11 1-162-215-31 1-161-494-00 1-104-665-11 1-162-288-31 CERAMIC CERAMIC CERAMIC ELECT CERAMIC < CONNECTOR > CN901 1-568-802-11 SOCKET, CONNECTOR 19P 0.1uF 47PF 0.022uF 100uF 330PF 50V 50V 25V 10V 50V
5% 20% 10%
1-249-417-11 CARBON
< LED > < ROTARY ENCODER > D901 D902 D903 D904 D905 D906 D907 D908 8-719-313-50 8-719-018-46 8-719-313-50 8-719-313-50 8-719-313-50 LED LED LED LED LED SEL6810A-TH12 (PLUS ONE) SEL3510C-CD () SEL6810A-TH12 (P) SEL6810A-TH12 (GROUP 1) SEL6810A-TH12 (GROUP 2) RE901 1-475-543-11 ENCODER, ROTARY (DISC/CHARACTER PUSH ENTER) < SWITCH > S901 S902 S903 S904 S905 S906 S907 S908 S909 S910 S911 S912 S913 S914 S915 S916 S917 S918 S919 S920 5% 5% 1/4W 1/4W 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 SWITCH, TACTILE (CLEAR) SWITCH, TACTILE (CHECK) SWITCH, TACTILE (FADER) SWITCH, TACTILE (MEMO SEARCH) SWITCH, TACTILE (INPUT) SWITCH, TACTILE (TIME/TEXT) SWITCH, TACTILE () SWITCH, TACTILE () SWITCH, TACTILE (p) SWITCH, TACTILE (P) SWITCH, TACTILE () SWITCH, TACTILE (PLUS ONE) SWITCH, TACTILE (REPEAT) SWITCH, TACTILE (PLAY MODE) SWITCH, TACTILE (GROUP 5) SWITCH, TACTILE (GROUP 4) SWITCH, TACTILE (GROUP 3) SWITCH, TACTILE (GROUP 2) SWITCH, TACTILE (GROUP 1) SWITCH, TACTILE (GROUP FILE)
8-719-313-50 LED SEL6810A-TH12 (GROUP 3) 8-719-313-50 LED SEL6810A-TH12 (GROUP 4) 8-719-313-50 LED SEL6810A-TH12 (GROUP 5) < FLUORESCENT INDICATOR TUBE >
FL901
R901 R902
680 1K
64
LED
Ref. No. * Part No. Description Remark Ref. No. CN801 1-668-581-11 LED BOARD ********* < CONNECTOR > CNP841 1-506-481-11 PIN, CONNECTOR 2P < LED > D841 D842 D843 8-719-057-10 LED LNJ301MPUJAB (INSIDE ILLUMINATION) 8-719-057-09 LED LNJ801LPDJA (INSIDE ILLUMINATION) 8-719-064-21 LED LNJ801TPSJA (INSIDE ILLUMINATION) < RESISTOR > R841 1-249-407-11 CARBON 150 5% 1/4W R842 1-249-410-11 CARBON 270 5% 1/4W R843 1-249-408-11 CARBON 180 5% 1/4W ************************************************************ * * * A-4724-007-A MAIN BOARD, COMPLETE (E) A-4724-012-A MAIN BOARD, COMPLETE (US, CND) A-4724-015-A MAIN BOARD, COMPLETE (AEP, UK, AED, SP, AUS) ******************** < CAPACITOR > C204 C205 C207 C208 C209 C210 C211 C212 C220 C221 C222 C250 C382 C501 C502 C503 C504 C505 C506 C507 C508 C509 C530 C531 1-126-768-11 1-126-768-11 1-126-965-11 1-126-963-11 1-126-963-11 1-126-935-11 1-126-927-11 1-126-935-11 1-126-963-11 1-126-935-11 1-126-963-11 1-126-962-11 1-126-962-11 1-161-494-00 1-161-494-00 1-104-665-11 1-162-306-11 1-162-306-11 1-162-306-11 1-162-294-31 1-162-306-11 1-161-494-00 1-110-489-11 1-164-159-11 ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC CERAMIC ELECT CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CAPACITOR CERAMIC < CONNECTOR > * CN501 * CN502 CN503 CN601 * CN603 * CN702 CN704 1-568-835-11 1-568-828-11 1-568-802-11 1-506-468-11 1-568-955-11 SOCKET, CONNECTOR 16P SOCKET, CONNECTOR 9P SOCKET, CONNECTOR 19P PIN, CONNECTOR 3P PIN, CONNECTOR 6P 2200uF 2200uF 22uF 4.7uF 4.7uF 470uF 2200uF 470uF 4.7uF 470uF 4.7uF 3.3uF 3.3uF 0.022uF 0.022uF 100uF 0.01uF 0.01uF 0.01uF 0.001uF 0.01uF 0.022uF 1F 0.1uF 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 16V 16V 50V 50V 50V 6.3V 10V 16V 50V 6.3V 50V 50V 50V 25V 25V 10V 16V 16V 16V 50V 16V 25V 5.5V 50V FB501 FB503 D206 D207 D210 D211 D212 D304 D382 D404 D501 8-719-921-54 8-719-982-22 8-719-991-33 8-719-921-42 8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33 Part No. Description 1-506-468-11 PIN, CONNECTOR 3P < DIODE > DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE MTZJ-6.2B MTZJ-30D 1SS133T-77 MTZJ-5.1A 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77
MAIN
Remark
< FERRITE BEAD > 1-412-473-21 INDUCTOR 1-412-473-21 INDUCTOR < IC > IC201 IC202 IC203 IC501 IC502 IC601 8-759-061-65 8-749-011-78 8-759-821-93 8-752-891-32 8-759-463-99 IC IC IC IC IC LA5602 BA17807T LA5601 CXP84340-071Q M5M5256DFP-70XL 0uH 0uH
L502
1-410-507-11 INDUCTOR
6.8uH
< TRANSISTOR > Q201 Q304 Q305 Q380 Q381 Q382 Q383 Q404 Q405 Q481 Q501 Q502 8-729-140-97 8-729-900-65 8-729-900-80 8-729-900-65 8-729-900-65 8-729-900-65 8-729-900-65 8-729-900-65 8-729-900-80 8-729-900-65 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SB734-34 DTA144ES DTC114ES DTA144ES DTA144ES DTA144ES DTA144ES DTA144ES DTC114ES DTA144ES
R201 R202 R210 R320 R322 R329 R330 R333 R334 R420 R422 R430 R501 R502
1-249-435-11 1-249-425-11 1-249-411-11 1-249-441-11 1-249-417-11 1-249-441-11 1-249-441-11 1-249-441-11 1-249-441-11 1-249-441-11 1-249-417-11 1-249-441-11 1-249-429-11 1-249-429-11
CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON
33K 4.7K 330 100K 1K 100K 100K 100K 100K 100K 1K 100K 10K 10K
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W
1-770-730-11 CONNECTOR, BOARD TO BOARD 11P 1-778-982-11 CONNECTOR, BOARD TO BOARD 13P
65
MAIN
Ref. No. R503 R504 R505 R506 R507 R508 R509 R510 R511 R512 R513 R514 R515 R516 R517 R519 R520 R522 R523 R530 R531 R532 R533 R601 R602 R603 R604 R605 R606 R607
MOTOR
Part No. 1-249-429-11 CARBON 1-249-429-11 1-249-429-11 1-249-427-11 1-249-427-11 1-249-427-11 1-249-429-11 1-249-429-11 1-249-429-11 1-249-429-11 1-249-429-11 1-249-429-11 1-249-429-11 1-249-429-11 1-249-437-11 1-249-429-11 1-249-429-11 1-249-427-11 1-249-425-11 1-249-429-11 1-249-429-11 1-249-403-11 1-249-403-11 1-249-429-11 1-249-428-11 1-249-382-11 1-249-382-11 1-247-850-11 1-249-429-11 1-247-807-31 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON
POWER SW
10K 10K 10K 6.8K 6.8K 6.8K 10K 10K 10K 10K 10K 10K 10K 10K 47K 10K 10K 6.8K 4.7K 10K 10K 68 68 10K 8.2K 1.2 1.2 6.2K 10K 100 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
SW
Remark 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/6W 1/6W 1/4W 1/4W 1/4W
TABLE SENSOR
Ref. No. D911 Part No. Description Remark 8-719-057-97 LED SEL5923A-TP15 (MEGA CONTROL) < TRANSISTOR > Q906 Q907 8-729-900-80 TRANSISTOR DTC114ES 8-729-119-76 TRANSISTOR 2SA1175-HFE < RESISTOR > R919 R920 R921 R946 R947 R948 R949 R950 R951 1-249-415-11 1-249-417-11 1-249-419-11 1-249-407-11 1-249-429-11 1-249-429-11 1-249-407-11 1-249-407-11 1-249-417-11 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON < SWITCH > S921 1-554-303-21 SWITCH, TACTILE (I/u) S922 1-554-303-21 SWITCH, TACTILE (X-FADE) S923 1-554-303-21 SWITCH, TACTILE (NO DELAY) S924 1-554-303-21 SWITCH, TACTILE (MEGA CONTROL) ************************************************************ * 1-663-975-11 SW BOARD ********* < CONNECTOR > * CN54 1-568-941-11 PIN, CONNECTOR 3P < SWITCH > S51 1-571-958-11 SWITCH, PUSH (1 KEY) (UP) S52 1-571-958-11 SWITCH, PUSH (1 KEY) (DOWN) ************************************************************ * 1-663-971-11 TABLE SENSOR BOARD ******************* < CONNECTOR > 680 1K 1.5K 150 10K 10K 150 150 1K 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W
Description
< VARIABLE RESISTOR > RV601 1-238-551-11 RES, ADJ, CARBON 220K < TEST PIN > TP501 1-564-506-11 PLUG, CONNECTOR 3P < VIBRATOR > X501 1-579-175-11 VIBRATOR, CERAMIC (10MHz) ************************************************************ * 1-663-974-11 MOTOR BOARD ************* < CONNECTOR > CN61 1-506-469-11 PIN, CONNECTOR 4P ************************************************************ * 1-668-578-11 POWER SW BOARD **************** < CONNECTOR > * CN903 1-568-943-11 PIN, CONNECTOR 5P < LED > D909 D910 8-719-057-09 LED LNJ801LPDJA (STANDBY) 8-719-057-97 LED SEL5923A-TP15 (MEGA CONTROL)
* CN51 CN52
1-568-944-11 PIN, CONNECTOR 6P 1-506-481-11 PIN, CONNECTOR 2P < PHOTO INTERRUPTER >
8-749-924-18 PHOTO INTERRUPTER RPI-1391 8-749-924-18 PHOTO INTERRUPTER RPI-1391 8-749-924-18 PHOTO INTERRUPTER RPI-1391 < RESISTOR >
R51 1-249-416-11 CARBON 820 5% 1/4W R52 1-249-416-11 CARBON 820 5% 1/4W R53 1-249-416-11 CARBON 820 5% 1/4W ************************************************************ MISCELLANEOUS ************** 67 ! 108 ! 108 ! 108 1-773-140-11 1-558-943-41 1-575-651-21 1-590-926-11 WIRE (FLAT TYPE) (19 CORE) CORD, POWER (E) CORD, POWER (AEP, AED, SP) CORD, POWER (US, CND) Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
66
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Ref. No. ! 108 ! 108 ! 109 111 119 322 ! 401 408 M101 M102 M61 M62 ! T501 ! T501
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1-696-845-11 CORD, POWER (AUS) 1-751-529-11 1-569-007-11 1-782-465-11 1-769-921-11 1-777-874-11 8-848-379-31 1-777-874-11 X-2646-110-2 X-2625-769-1 X-4948-434-1 CORD, POWER (UK) ADAPTOR, CONVERSION 2P (E) WIRE (FLAT TYPE) (16 CORE) WIRE (FLAT TYPE) (9 CORE) WIRE (FLAT TYPE) (16 CORE) OPTICAL PICK-UP KSS-213B/S-N WIRE (FLAT TYPE) (16 CORE) T, T CHASSIS ASSY (MG) (F) (SPINDLE) MOTOR GEAR ASSY (MB) (RP) (SLED) MOTOR ASSY (LOADING)
X-4948-434-1 MOTOR ASSY (TABLE) 1-431-333-11 TRANSFORMER, POWER (US, CND) 1-431-334-11 TRANSFORMER, POWER (AEP, UK, AED, SP, AUS) ! T501 1-431-335-11 TRANSFORMER, POWER (E) ************************************************************ ACCESSORIES & PACKING MATERIALS ******************************** 1-475-607-11 1-558-271-11 1-777-241-11 3-810-765-32 REMOTE COMMANDER (RM-DX57) CORD, CONNECTION (AUDIO 108cm) CORD, CONNECTION (CONTROL A1) (CND) MANUAL, COMMONNESS INSTRUCTION (ENGLISH) (US, AUS) 3-810-765-42 MANUAL, COMMONNESS INSTRUCTION (ENGLISH,FRENCH, GERMAN, ITALIAN, SPANISH, DUTCH,SWEDISH, PORTUGUESE, CHINESE) (CND, AEP, E, SP) 3-862-557-11 MANUAL, INSTRUCTION (ENGLISH) (EXCEP AED) 3-862-557-21 MANUAL, INSTRUCTION (FRENCH, SPANISH, CHINESE) (CND, AEP, E, SP) 3-862-557-31 MANUAL, INSTRUCTION (GERMAN, DUTCH, ITALIAN, PORTUGUESE) (AEP) 3-862-557-41 MANUAL, INSTRUCTION (SWEDISH, FINNISH, DANISH) (AED) 4-981-643-01 COVER, BATTERY (for RM-DX57) 4-991-161-01 LET (50), BOOK * 4-991-854-01 LABEL (DISC) ************************************************************ ************** HARDWARE LIST ************** #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 #12 #13 7-685-871-01 7-685-534-19 7-685-646-79 7-685-872-09 7-685-647-79 7-685-873-09 7-685-132-19 7-685-107-11 7-685-535-19 7-685-134-19 SCREW +BVTT 3X6 (S) SCREW +BTP 2.6X8 TYPE2 N-S SCREW +BVTP 3X8 TYPE2 N-S SCREW +BVTT 3X8 (S) SCREW +BVTP 3X10 TYPE2 N-S SCREW +BVTT 3X10 (S) SCREW +BTP 2.6X5 TYPE2 N-S SCREW +P 2X12 TYPE2 NON-SLIT SCREW +BTP 2.6X10 TYPE2 N-S SCREW (+ PTPWH) (2.6X8)
7-621-770-67 SCREW +PWH 2.6X6 7-685-649-79 SCREW +P 3X14 TYPE2 NON-SLIT 7-621-255-15 SCREW +P 2X3
67
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
CDP-CX57
Sony Corporation
9-922-818-11
Home A&V Products Company
68