BPE BIO-PHARM FITTINGS CATALOG

Simplifying Sanitary Through Superior Service™

Home of
BPE FITTINGS

TABLE OF CONTENTS

BPE FITTINGS INTRODUCTION................... 1 FERRULES & CAPS............................................. 35-36

ELBOWS................................................................ 4-8 CLAMPS & GASKETS......................................... 37-39
TEES & CROSSES................................................. 9-19 TUBING................................................................. 40
REDUCERS........................................................... 20-31 INDUSTRY CROSS REFERENCE..................... 41

USE POINTS......................................................... 32-33 GLOSSARY OF TERMS....................................... 42-43

STUB ENDS.......................................................... 34

ABOUT US
Steel & O’Brien is a domestic manufacturer of sanitary stainless steel fittings for the food processing,
pharmaceutical and various other industries, located in Western New York.

Founded in 1990, S&O specializes in quick turn around, custom fittings and very competitive pricing.

Our 205,000 square foot facility, maintains over twenty-five million dollars in finished goods inventory as
well as over one million dollars in raw materials inventory.

INTRODUCTION
Steel & O’Brien offers a full line of ASME-BPE compliant fittings for the Pharmaceutical and Biotech
Industries. Ranging in sizes from 1/2” - 6” with weld and clamp end connections, in 316L material.

Traceability All fittings are marked according to the latest ASME-BPE specifications.
Permanently marking each fitting allows for full traceability back to the original
stainless steel used to make the part. All Material Test Reports are available upon
request or at steelobrien.com.

Quality Every BPE fitting is inspected by a highly trained staff to the latest ASME-BPE
specifications.

Packing To prevent damage and contamination all BPE fittings are capped and bagged in
transparent bags.

Boroscoping Ability to inspect and record welds with an inside diameter of .370 and larger.
With a reach of up to 76” from access port. Our high resolution boroscope gives
Steel and O’Brien the ability to inspect for ASME-BPE weld discoloration acceptance.

1
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
 BPE FITTINGS

INTRODUCTION
Polishing Polishing is an important component for BPE fittings. Polish offerings
are shown below and comply to the latest ASME-BPE requirements

Inside Surface Outside Surface

Surface Finish Code BPE Designation Ra Max.
Polish Method Polish Method
μ-in. μm
PU SF0 Unpolished Unpolished
PC SF1 20 0.51 Mechanical Polish Unpolished
PL SF1 20 0.51 Mechanical Polish Mechanical Polish (32Ra)
PD SF4 15 0.38 Mechanical Polish & Electropolish Unpolished
PM SF4 15 0.38 Mechanical Polish & Electropolish Mechanical Polish (32Ra)

SPECIAL FABRICATIONS
Steel & O’Brien provides custom fabrications in stainless steel as well as other alloys including Hastelloy,
AL6XN, Titanium, Monel and Inconel.

Our experienced team of engineers, machinists, welders, and polishers can take your design from
drawing to finished product while meeting and often exceeding customer specifications. Industry
leading delivery times keeps your project on time.

Give us a call for a prompt quote on your custom fabrication needs.

2 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS

DIMENSIONS & TOLERANCES

As specified in ASME BPE Part DT-3-1

Nominal Wall Thickness Wall Thickness Squareness Face to Off Angle Equivalent Off Plane, P Centerline
Size O.D. (Mechanical Polish) (Electropolish) Tangent, B O (max.) Angle (O) (max.) Radius
(max.) (max.) (CLR), R
in. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm.
1/4 ±0.005 ±0.13 +0.003/-0.004 +0.08/-0.10 +0.003/-0.006 +0.08/-0.15 0.005 0.13 0.009 0.23 2.1 0.030 0.76 0.563 14.30
3/8 ±0.005 ±0.13 +0.003/-0.004 +0.08/-0.10 +0.003/-0.006 +0.08/-0.15 0.005 0.13 0.012 0.30 1.8 0.030 0.76 1.125 28.58
1/2 ±0.005 ±0.13 +0.005/-0.008 +0.13/-0.20 +0.005/-0.010 +0.13/-0.25 0.005 0.13 0.014 0.36 1.6 0.030 0.76 1.125 28.58
3/4 ±0.005 ±0.13 +0.005/-0.008 +0.13/-0.20 +0.005/-0.010 +0.13/-0.25 0.005 0.13 0.018 0.46 1.4 0.030 0.76 1.125 28.58
1 ±0.005 ±0.13 +0.005/-0.008 +0.13/-0.20 +0.005/-0.010 +0.13/-0.25 0.008 0.20 0.025 0.64 1.4 0.030 0.76 1.500 38.10
1-1/2 ±0.008 ±0.20 +0.005/-0.008 +0.13/-0.20 +0.005/-0.010 +0.13/-0.25 0.008 0.20 0.034 0.86 1.3 0.050 1.27 2.250 57.15
2 ±0.008 ±0.20 +0.005/-0.008 +0.13/-0.20 +0.005/-0.010 +0.13/-0.25 0.008 0.20 0.043 1.09 1.2 0.050 1.27 3.000 76.20
2-1/2 ±0.010 ±0.25 +0.005/-0.008 +0.13/-0.20 +0.005/-0.010 +0.13/-0.25 0.010 0.25 0.054 1.37 1.2 0.050 1.27 3.750 95.25
3 ±0.010 ±0.25 +0.005/-0.008 +0.13/-0.20 +0.005/-0.010 +0.13/-0.25 0.016 0.41 0.068 1.73 1.3 0.050 1.27 4.500 114.30
4 ±0.015 ±0.38 +0.008/-0.010 +0.38/-0.38 +0.008/-0.012 +0.20/-0.30 0.016 0.41 0.086 2.18 1.2 0.060 1.52 6.000 152.40
6 ±0.030 ±0.76 +0.015/-0.015 +0.38/-0.20 +0.015/-0.017 +0.38/-0.43 0.030 0.76 0.135 3.43 1.3 0.060 1.52 9.000 228.60

General Notes:
1) Tolerances for “E” end-to-end and center-to-end = .050 in (1.27mm)
2) Tolerance for centerline radius (CLR) = ±10% of the nominal O.D. Dimension

3
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
ELBOWS BPE FITTINGS

S2S - 90 DEGREE ELBOW, TANGENT WELD ENDS

PART NUMBER SIZE A R

S2S-.50 1/2 3.000 1.125
S2S-.75 3/4 3.000 1.125
S2S-1 1 3.000 1.500
S2S-1.5 1-1/2 3.750 2.250
S2S-2 2 4.750 3.000
S2S-2.5 2-1/2 5.500 3.750
S2S-3 3 6.250 4.500
S2S-4 4 8.000 6.000
S2S-6 6 11.500 9.000
BPE TABLE DT-4.1.1-1

S2CKW - 90 DEGREE ELBOW, TANGENT WELD END X CLAMP

PART NUMBER SIZE A B R

S2CKW-.50 1/2 1.625 3.000 1.125
S2CKW-.75 3/4 1.625 3.000 1.125
S2CKW-1 1 2.000 3.000 1.500
S2CKW-1.5 1-1/2 2.750 3.750 2.250
S2CKW-2 2 3.500 4.750 3.000
S2CKW-2.5 2-1/2 4.250 5.500 3.750
S2CKW-3 3 5.000 6.250 4.500
S2CKW-4 4 6.625 8.000 6.000
S2CKW-6 6 10.500 11.500 9.000
BPE TABLE DT-4.1.1-2

S2KS - 45 DEGREE ELBOW, TANGENT WELD ENDS

PART NUMBER SIZE A R

S2KS-.50 1/2 2.250 1.125
S2KS-.75 3/4 2.250 1.125
S2KS-1 1 2.250 1.500
S2KS-1.5 1-1/2 2.500 2.250
S2KS-2 2 3.000 3.000
S2KS-2.5 2-1/2 3.375 3.750
S2KS-3 3 3.625 4.500
S2KS-4 4 4.500 6.000
S2KS-6 6 6.250 9.000
BPE TABLE DT-4.1.1-4

4 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS 88-92 DEGREE ELBOWS

S2KKW - 45 DEGREE ELBOW, TANGENT WELD END X CLAMP

PART NUMBER SIZE A B R

S2KKW-.50 1/2 2.250 1.000 1.125
S2KKW-.75 3/4 2.250 1.000 1.125
S2KKW-1 1 2.250 1.125 1.500
S2KKW-1.5 1-1/2 2.500 1.438 2.250
S2KKW-2 2 3.000 1.750 3.000
S2KKW-2.5 2-1/2 3.375 2.063 3.750
S2KKW-3 3 3.625 2.375 4.500
S2KKW-4 4 4.500 3.125 6.000
S2KKW-6 6 6.250 5.250 9.000
BPE TABLE DT-4.1.1-5

S2CMP - 90 DEGREE ELBOW, CLAMP ENDS

PART NUMBER SIZE A R

S2CMP-.50 1/2 1.625 1.125
S2CMP-.75 3/4 1.625 1.125
S2CMP-1 1 2.000 1.500
S2CMP-1.5 1-1/2 2.750 2.250
S2CMP-2 2 3.500 3.000
S2CMP-2.5 2-1/2 4.250 3.750
S2CMP-3 3 5.000 4.500
S2CMP-4 4 6.625 6.000
S2CMP-6 6 10.500 9.000
BPE TABLE DT-4.1.1-3

S2KMP - 45 DEGREE ELBOW, CLAMP ENDS

PART NUMBER SIZE A R

S2KMP-.50 1/2 1.000 1.125
S2KMP-.75 3/4 1.000 1.125
S2KMP-1 1 1.125 1.500
S2KMP-1.5 1-1/2 1.438 2.250
S2KMP-2 2 1.750 3.000
S2KMP-2.5 2-1/2 2.063 3.750
S2KMP-3 3 2.375 4.500
S2KMP-4 4 3.125 6.000
S2KMP-6 6 5.250 9.000
BPE TABLE DT-4.1.1-6

5
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
88-92 DEGREE ELBOWS BPE FITTINGS

S2S88 - 88 DEGREE ELBOW TANGENT WELD ENDS

PART NUMBER SIZE A R

S2S88-.50 1/2 3.065 1.125
S2S88-.75 3/4 3.065 1.125
S2S88-1 1 3.051 1.500
S2S88-1.5 1-1/2 3.801 2.250
S2S88-2 2 4.809 3.000
S2S88-2.5 2-1/2 5.559 3.750
S2S88-3 3 6.308 4.500
S2S88-4 4 8.066 6.000
BPE TABLE DT-4.1.1-9

S2S92 - 92 DEGREE ELBOW TANGENT WELD ENDS

PART NUMBER SIZE A R

S2S92-.50 1/2 2.934 1.125
S2S92-.75 3/4 2.934 1.125
S2S92-1 1 2.947 1.500
S2S92-1.5 1-1/2 3.696 2.250
S2S92-2 2 4.687 3.000
S2S92-2.5 2-1/2 5.437 3.750
S2S92-3 3 6.186 4.500
S2S92-4 4 7.930 6.000

BPE TABLE DT-4.1.1-10

6 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS 88-92 DEGREE ELBOWS

S2CKW88 - 88 DEGREE ELBOW, TANGENT WELD END X CLAMP END

PART NUMBER SIZE A B R

S2CKW88-.50 1/2 1.690 3.017 1.125
S2CKW88-.75 3/4 1.725 3.018 1.125
S2CKW88-1 1 2.051 3.017 1.500
S2CKW88-1.5 1-1/2 2.801 3.766 2.250
S2CKW88-2 2 3.559 4.766 3.000
S2CKW88-2.5 2-1/2 4.309 5.515 3.750
S2CKW88-3 3 5.058 6.265 4.500
S2CKW88-4 4 6.691 8.018 6.000

S2CKW92 - 92 DEGREE ELBOW, TANGENT WELD END X CLAMP END

PART NUMBER SIZE A B R

S2CKW92-.50 1/2 1.607 2.980 1.125
S2CKW92-.75 3/4 1.607 2.980 1.125
S2CKW92-1 1 1.877 2.983 1.500
S2CKW92-1.5 1-1/2 2.696 3.731 2.250
S2CKW92-2 2 3.298 4.736 3.000
S2CKW92-2.5 2-1/2 4.012 5.486 3.750
S2CKW92-3 3 4.727 6.232 4.500
S2CKW92-4 4 6.272 7.988 6.000

7
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
88-92 DEGREE ELBOWS BPE FITTINGS

S2CMP88 - 88 DEGREE ELBOW CLAMP ENDS

PART NUMBER SIZE A R

S2CMP88-.50 1/2 1.642 1.125
S2CMP88-.75 3/4 1.647 1.125
S2CMP88-1 1 2.017 1.500
S2CMP88-1.5 1-1/2 2.766 2.250
S2CMP88-2 2 3.516 3.000
S2CMP88-2.5 2-1/2 4.265 3.750
S2CMP88-3 3 5.015 4.500
S2CMP88-4 4 6.644 6.000

S2CMP92 - 92 DEGREE ELBOW CLAMP ENDS

PART NUMBER SIZE A R

S2CMP92-.50 1/2 1.607 1.125
S2CMP92-.75 3/4 1.667 1.125
S2CMP92-1 1 1.982 1.500
S2CMP92-1.5 1-1/2 2.731 2.250
S2CMP92-2 2 3.476 3.000
S2CMP92-2.5 2-1/2 4.226 3.750
S2CMP92-3 3 4.975 4.500
S2CMP92-4 4 6.592 6.000

8 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS TEES

S7WWW - TEE, TANGENT WELD ENDS

PART NUMBER SIZE A B

S7WWW-.50 1/2 1.875 3.750
S7WWW-.75 3/4 2.000 4.000
S7WWW-1 1 2.125 4.250
S7WWW-1.5 1-1/2 2.375 4.750
S7WWW-2 2 2.875 5.750
S7WWW-2.5 2-1/2 3.125 6.250
S7WWW-3 3 3.375 6.750
S7WWW-4 4 4.125 8.250
S7WWW-6 6 5.625 11.250
BPE TABLE DT-4.1.2-1

S7SWWK - TEE, TANGENT WELD ENDS x SHORT CLAMP OUTLET

PART NUMBER SIZE A B C

S7SWWK-.50 1/2 1.875 3.750 1.000
S7SWWK-.75 3/4 2.000 4.000 1.125
S7SWWK-1 1 2.125 4.250 1.125
S7SWWK-1.5 1-1/2 2.375 4.750 1.375
S7SWWK-2 2 2.875 5.750 1.625
S7SWWK-2.5 2-1/2 3.125 6.250 1.875
S7SWWK-3 3 3.375 6.750 2.125
S7SWWK-4 4 4.125 8.250 2.750
S7SWWK-6 6 5.625 11.250 4.625
BPE TABLE DT-4.1.2-2

S7WWK - TEE, TANGENT WELD ENDS x CLAMP OUTLET

PART NUMBER SIZE A B C

S7WWK-.50 1/2 1.875 3.750 2.375
S7WWK-.75 3/4 2.000 4.000 2.500
S7WWK-1 1 2.125 4.250 2.625
S7WWK-1.5 1-1/2 2.375 4.750 2.875
S7WWK-2 2 2.875 5.750 3.375
S7WWK-2.5 2-1/2 3.125 6.250 3.625
S7WWK-3 3 3.375 6.750 3.875
S7WWK-4 4 4.125 8.250 4.750
S7WWK-6 6 5.625 11.250 7.125
BPE TABLE DT-4.1.2-12

9
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
TEES BPE FITTINGS

S7WSKW - TEE, TANGENT WELD ENDS x CLAMP SHORT RUN

PART NUMBER SIZE A B C

S7WSKW-.50 1/2 1.875 2.750 1.875
S7WSKW-.75 3/4 2.000 3.000 2.000
S7WSKW-1 1 2.125 3.250 2.125
S7WSKW-1.5 1-1/2 2.375 3.750 2.375
S7WSKW-2 2 2.875 4.500 2.875
S7WSKW-2.5 2-1/2 3.125 5.000 3.125
S7WSKW-3 3 3.375 5.500 3.375
S7WSKW-4 4 4.125 6.875 4.125
S7WSKW-6 6 5.625 10.250 5.625
BPE TABLE DT-4.1.2-3

S7MPS - TEE, CLAMP ENDS x SHORT CLAMP OUTLET

PART NUMBER SIZE A B C

S7MPS-.50 1/2 2.375 4.750 1.000
S7MPS-.75 3/4 2.500 5.000 1.125
S7MPS-1 1 2.625 5.250 1.125
S7MPS-1.5 1-1/2 2.875 5.750 1.375
S7MPS-2 2 3.375 6.750 1.625
S7MPS-2.5 2-1/2 3.625 7.250 1.875
S7MPS-3 3 3.875 7.750 2.125
S7MPS-4 4 4.750 9.500 2.750
S7MPS-6 6 7.125 14.250 4.625
BPE TABLE DT-4.1.2-5

S7MP - TEE, CLAMP ENDS

PART NUMBER SIZE A B

S7MP-.50 1/2 2.375 4.750
S7MP-.75 3/4 2.500 5.000
S7MP-1 1 2.625 5.250
S7MP-1.5 1-1/2 2.875 5.750
S7MP-2 2 3.375 6.750
S7MP-2.5 2-1/2 3.625 7.250
S7MP-3 3 3.875 7.750
S7MP-4 4 4.750 9.500
S7MP-6 6 7.125 14.250
BPE TABLE DT-4.1.2-4

10 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS REDUCING TEES

S7RWWW - REDUCING TEE, TANGENT WELD ENDS

PART NUMBER SIZE A B C

S7RWWW-.75X.50 3/4 X 1/2 2.000 4.000 2.000

S7RWWW-1X.50 1 X 1/2 2.125 4.250 2.125
S7RWWW-1X.75 1 X 3/4 2.125 4.250 2.125
S7RWWW-1.5X.50 1-1/2 X 1/2 2.375 4.750 2.375
S7RWWW-1.5X.75 1-1/2 X 3/4 2.375 4.750 2.375
S7RWWW-1.5X1 1-1/2 X 1 2.375 4.750 2.375
S7RWWW-2X.50 2 X 1/2 2.875 5.750 2.625
S7RWWW-2X.75 2 X 3/4 2.875 5.750 2.625
S7RWWW-2X1 2X1 2.875 5.750 2.625
S7RWWW-2X1.5 2 X 1-1/2 2.875 5.750 2.625
S7RWWW-2.5X.50 2-1/2 X 1/2 3.125 6.250 2.875
S7RWWW-2.5X.75 2-1/2 X 3/4 3.125 6.250 2.875
S7RWWW-2.5X1 2-1/2 X 1 3.125 6.250 2.875
S7RWWW-2.5X1.5 2-1/2 X 1-1/2 3.125 6.250 2.875
S7RWWW-2.5X2 2-1/2 X 2 3.125 6.250 2.875
S7RWWW-3X.50 3 X 1/2 3.375 6.750 3.125
S7RWWW-3X.75 3 X 3/4 3.375 6.750 3.125
S7RWWW-3X1 3X1 3.375 6.750 3.125
S7RWWW-3X1.5 3 X 1-1/2 3.375 6.750 3.125
S7RWWW-3X2 3X2 3.375 6.750 3.125
S7RWWW-3X2.5 3 X 2-1/2 3.375 6.750 3.125
S7RWWW-4X.50 4 X 1/2 4.125 8.250 3.625
S7RWWW-4X.75 4 X 3/4 4.125 8.250 3.625
S7RWWW-4X1 4X1 4.125 8.250 3.625
S7RWWW-4X1.5 4 X 1-1/2 4.125 8.250 3.625
S7RWWW-4X2 4X2 4.125 8.250 3.875
S7RWWW-4X2.5 4 X 2-1/2 4.125 8.250 3.875
S7RWWW-4X3 4X3 4.125 8.250 3.875
S7RWWW-6X.50 6 X 1/2 5.625 11.250 4.625
S7RWWW-6X.75 6 X 3/4 5.625 11.250 4.625
S7RWWW-6X1 6X1 5.625 11.250 4.625
S7RWWW-6X1.5 6 X 1-1/2 5.625 11.250 4.625
S7RWWW-6X2 6X2 5.625 11.250 4.875
S7RWWW-6X2.5 6 X 2-1/2 5.625 11.250 4.875
S7RWWW-6X3 6X3 5.625 11.250 4.875
S7RWWW-6X4 6X4 5.625 11.250 5.125

BPE TABLE DT-4.1.2-6

11
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
REDUCING TEES BPE FITTINGS

S7RWWK - REDUCING TEE, TANGENT WELD ENDS x CLAMP END BRANCH

PART NUMBER SIZE A B C

S7RWWK-.75X.50 3/4 X 1/2 2.000 4.000 2.500

S7RWWK-1X.50 1 X 1/2 2.125 4.250 2.625
S7RWWK-1X.75 1 X 3/4 2.125 4.250 2.625
S7RWWK-1.5X.50 1-1/2 X 1/2 2.375 4.750 2.875
S7RWWK-1.5X.75 1-1/2 X 3/4 2.375 4.750 2.875
S7RWWK-1.5X1 1-1/2 X 1 2.375 4.750 2.875
S7RWWK-2X.50 2 X 1/2 2.875 5.750 3.125
S7RWWK-2X.75 2 X 3/4 2.875 5.750 3.125
S7RWWK-2X1 2X1 2.875 5.750 3.125
S7RWWK-2X1.5 2 X 1-1/2 2.875 5.750 3.125
S7RWWK-2.5X.50 2-1/2 X 1/2 3.125 6.250 3.375
S7RWWK-2.5X.75 2-1/2 X 3/4 3.125 6.250 3.375
S7RWWK-2.5X1 2-1/2 X 1 3.125 6.250 3.375
S7RWWK-2.5X1.5 2-1/2 X 1-1/2 3.125 6.250 3.375
S7RWWK-2.5X2 2-1/2 X 2 3.125 6.250 3.375
S7RWWK-3X.50 3 X 1/2 3.375 6.750 3.625
S7RWWK-3X.75 3 X 3/4 3.375 6.750 3.625
S7RWWK-3X1 3X1 3.375 6.750 3.625
S7RWWK-3X1.5 3 X 1-1/2 3.375 6.750 3.625
S7RWWK-3X2 3X2 3.375 6.750 3.625
S7RWWK-3X2.5 3 X 2-1/2 3.375 6.750 3.625
S7RWWK-4X.50 4 X 1/2 4.125 8.250 4.125
S7RWWK-4X.75 4 X 3/4 4.125 8.250 4.125
S7RWWK-4X1 4X1 4.125 8.250 4.125
S7RWWK-4X1.5 4 X 1-1/2 4.125 8.250 4.125
S7RWWK-4X2 4X2 4.125 8.250 4.375
S7RWWK-4X2.5 4 X 2-1/2 4.125 8.250 4.375
S7RWWK-4X3 4X3 4.125 8.250 4.375
S7RWWK-6X.50 6 X 1/2 5.625 11.250 5.125
S7RWWK-6X.75 6 X 3/4 5.625 11.250 5.125
S7RWWK-6X1 6X1 5.625 11.250 5.125
S7RWWK-6X1.5 6 X 1-1/2 5.625 11.250 5.125
S7RWWK-6X2 6X2 5.625 11.250 5.375
S7RWWK-6X2.5 6 X 2-1/2 5.625 11.250 5.375
S7RWWK-6X3 6X3 5.625 11.250 5.375
S7RWWK-6X4 6X4 5.625 11.250 5.750

BPE TABLE DT-4.1.2-13

12 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS REDUCING TEES

S7RSWWK - REDUCING TEE, TANGENT WELD ENDS x SHORT CLAMP BRANCH

PART NUMBER SIZE A B C

S7RSWWK-.75X.50 3/4 X 1/2 2.000 4.000 1.000

S7RSWWK-1X.50 1 X 1/2 2.125 4.250 1.125
S7RSWWK-1X.75 1 X 3/4 2.125 4.250 1.125
S7RSWWK-1.5X.50 1-1/2 X 1/2 2.375 4.750 1.375
S7RSWWK-1.5X.75 1-1/2 X 3/4 2.375 4.750 1.375
S7RSWWK-1.5X1 1-1/2 X 1 2.375 4.750 1.375
S7RSWWK-2X.50 2 X 1/2 2.875 5.750 1.625
S7RSWWK-2X.75 2 X 3/4 2.875 5.750 1.625
S7RSWWK-2X1 2X1 2.875 5.750 1.625
S7RSWWK-2X1.5 2 X 1-1/2 2.875 5.750 1.625
S7RSWWK-2.5X.50 2-1/2 X 1/2 3.125 6.250 1.875
S7RSWWK-2.5X.75 2-1/2 X 3/4 3.125 6.250 1.875
S7RSWWK-2.5X1 2-1/2 X 1 3.125 6.250 1.875
S7RSWWK-2.5X1.5 2-1/2 X 1-1/2 3.125 6.250 1.875
S7RSWWK-2.5X2 2-1/2 X 2 3.125 6.250 1.875
S7RSWWK-3X.50 3 X 1/2 3.375 6.750 2.125
S7RSWWK-3X.75 3 X 3/4 3.375 6.750 2.125
S7RSWWK-3X1 3X1 3.375 6.750 2.125
S7RSWWK-3X1.5 3 X 1-1/2 3.375 6.750 2.125
S7RSWWK-3X2 3X2 3.375 6.750 2.125
S7RSWWK-3X2.5 3 X 2-1/2 3.375 6.750 2.125
S7RSWWK-4X.50 4 X 1/2 4.125 8.250 2.625
S7RSWWK-4X.75 4 X 3/4 4.125 8.250 2.625
S7RSWWK-4X1 4X1 4.125 8.250 2.625
S7RSWWK-4X1.5 4 X 1-1/2 4.125 8.250 2.625
S7RSWWK-4X2 4X2 4.125 8.250 2.625
S7RSWWK-4X2.5 4 X 2-1/2 4.125 8.250 2.625
S7RSWWK-4X3 4X3 4.125 8.250 2.625
S7RSWWK-6X3 6X3 5.625 11.250 3.625
S7RSWWK-6X4 6X4 5.625 11.250 3.750
BPE TABLE DT-4.1.2-7

13
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
REDUCING TEES BPE FITTINGS

S7RMP - REDUCING TEE, CLAMP ENDS

PART NUMBER SIZE A B C

S7RMP-.75X.50 3/4 X 1/2 2.500 5.000 2.500

S7RMP-1X.50 1 X 1/2 2.625 5.250 2.625
S7RMP-1X.75 1 X 3/4 2.625 5.250 2.625
S7RMP-1.5X.50 1-1/2 X 1/2 2.875 5.750 2.875
S7RMP-1.5X.75 1-1/2 X 3/4 2.875 5.750 2.875
S7RMP-1.5X1 1-1/2 X 1 2.875 5.750 2.875
S7RMP-2X.50 2 X 1/2 3.375 6.750 3.125
S7RMP-2X.75 2 X 3/4 3.375 6.750 3.125
S7RMP-2X1 2X1 3.375 6.750 3.125
S7RMP-2X1.5 2 X 1-1/2 3.375 6.750 3.125
S7RMP-2.5X.50 2-1/2 X 1/2 3.625 7.250 3.375
S7RMP-2.5X.75 2-1/2 X 3/4 3.625 7.250 3.375
S7RMP-2.5X1 2-1/2 X 1 3.625 7.250 3.375
S7RMP-2.5X1.5 2-1/2 X 1-1/2 3.625 7.250 3.375
S7RMP-2.5X2 2-1/2 X 2 3.625 7.250 3.375
S7RMP-3X.50 3 X 1/2 3.875 7.750 3.625
S7RMP-3X.75 3 X 3/4 3.875 7.750 3.625
S7RMP-3X1 3X1 3.875 7.750 3.625
S7RMP-3X1.5 3 X 1-1/2 3.875 7.750 3.625
S7RMP-3X2 3X2 3.875 7.750 3.625
S7RMP-3X2.5 3 X 2-1/2 3.875 7.750 3.625
S7RMP-4X.50 4 X 1/2 4.750 9.500 4.125
S7RMP-4X.75 4 X 3/4 4.750 9.500 4.125
S7RMP-4X1 4X1 4.750 9.500 4.125
S7RMP-4X1.5 4 X 1-1/2 4.750 9.500 4.125
S7RMP-4X2 4X2 4.750 9.500 4.375
S7RMP-4X2.5 4 X 2-1/2 4.750 9.500 4.375
S7RMP-4X3 4X3 4.750 9.500 4.375
S7RMP-6X3 6X3 7.125 14.250 5.375
S7RMP-6X4 6X4 7.125 14.250 5.750
BPE TABLE DT-4.1.2-8

14 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS REDUCING TEES

S7RMPS - REDUCING TEE, SHORT OUTLET CLAMP ENDS

PART NUMBER SIZE A B C

S7RMPS-.75X.50 3/4 X 1/2 2.500 5.000 1.000

S7RMPS-1X.50 1 X 1/2 2.625 5.250 1.125
S7RMPS-1X.75 1 X 3/4 2.625 5.250 1.125
S7RMPS-1.5X.50 1-1/2 X 1/2 2.875 5.750 1.375
S7RMPS-1.5X.75 1-1/2 X 3/4 2.875 5.750 1.375
S7RMPS-1.5X1 1-1/2 X 1 2.875 5.750 1.375
S7RMPS-2X.50 2 X 1/2 3.375 6.750 1.625
S7RMPS-2X.75 2 X 3/4 3.375 6.750 1.625
S7RMPS-2X1 2X1 3.375 6.750 1.625
S7RMPS-2X1.5 2 X 1-1/2 3.375 6.750 1.625
S7RMPS-2.5X.50 2-1/2 X 1/2 3.625 7.250 1.875
S7RMPS-2.5X.75 2-1/2 X 3/4 3.625 7.250 1.875
S7RMPS-2.5X1 2-1/2 X 1 3.625 7.250 1.875
S7RMPS-2.5X1.5 2-1/2 X 1-1/2 3.625 7.250 1.875
S7RMPS-2.5X2 2-1/2 X 2 3.625 7.250 1.875
S7RMPS-3X.50 3 X 1/2 3.875 7.750 2.125
S7RMPS-3X.75 3 X 3/4 3.875 7.750 2.125
S7RMPS-3X1 3X1 3.875 7.750 2.125
S7RMPS-3X1.5 3 X 1-1/2 3.875 7.750 2.125
S7RMPS-3X2 3X2 3.875 7.750 2.125
S7RMPS-3X2.5 3 X 2-1/2 3.875 7.750 2.125
S7RMPS-4X.50 4 X 1/2 4.750 9.500 2.625
S7RMPS-4X.75 4 X 3/4 4.750 9.500 2.625
S7RMPS-4X1 4X1 4.750 9.500 2.625
S7RMPS-4X1.5 4 X 1-1/2 4.750 9.500 2.625
S7RMPS-4X2 4X2 4.750 9.500 2.625
S7RMPS-4X2.5 4 X 2-1/2 4.750 9.500 2.625
S7RMPS-4X3 4X3 4.750 9.500 2.625
S7RMPS-6X3 6X3 7.125 14.250 3.625
S7RMPS-6X4 6X4 7.125 14.250 3.750
BPE TABLE DT-4.1.2-9

15
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
OFF ANGLE TEES BPE FITTINGS

S7WWW176 - 176 DEGREE TEE, TANGENT WELD ENDS

PART NUMBER SIZE A B C

S7WWW176-.50 1/2 1.874 3.748 1.940
S7WWW176-.75 3/4 1.999 3.998 2.070
S7WWW176-1 1 2.124 4.247 2.199
S7WWW176-1.5 1-1/2 2.374 4.747 2.458
S7WWW176-2 2 2.873 5.746 2.967
S7WWW176-2.5 2-1/2 3.123 6.246 3.234
S7WWW176-3 3 3.373 6.746 3.493
S7WWW176-4 4 4.123 8.245 4.269

S7WWW88 - 88 DEGREE TEE, TANGENT WELD ENDS

PART NUMBER SIZE A B C

S7WWW88-.50 1/2 1.875 3.750 1.874
S7WWW88-.75 3/4 2.000 4.000 1.999
S7WWW88-1 1 2.125 4.250 2.124
S7WWW88-1.5 1-1/2 2.375 4.750 2.374
S7WWW88-2 2 2.875 5.750 2.873
S7WWW88-2.5 2-1/2 3.125 6.250 3.123
S7WWW88-3 3 3.375 6.750 3.373
S7WWW88-4 4 4.125 8.250 4.122

16 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS INSTRUMENT TEES

S7IWWKS - INSTRUMENT TEE, WELD ENDS x CLAMP END

PART NUMBER SIZE A B C

S7IWWKS-.50X1.5 1/2 x 1-1/2 2.500 5.000 .875
S7IWWKS-.75X1.5 3/4 x 1-1/2 2.500 5.000 1.000
S7IWWKS-1X1.5 1 x 1-1/2 2.500 5.000 1.125
S7IWWKS-.50X2 1/2 x 2 2.750 5.500 1.000
S7IWWKS-.75X2 3/4 x 2 2.750 5.500 1.125
S7IWWKS-1X2 1x2 2.750 5.500 1.250
S7IWWKS-1.5X2 1-1/2 x 2 2.750 5.500 1.500
BPE TABLE DT-4.1.2-10

S7IMPS - INSTRUMENT TEE, CLAMP ENDS

PART NUMBER SIZE A B C

S7IMPS-.50X1.5 1/2 x 1-1/2 3.000 6.000 .875
S7IMPS-.75X1.5 3/4 x 1-1/2 3.000 6.000 1.000
S7IMPS-1X1.5 1 x 1-1/2 3.000 6.000 1.125
S7IMPS-.50X2 1/2 x 2 3.250 6.500 1.000
S7IMPS-.75X2 3/4 x 2 3.250 6.500 1.125
S7IMPS-1X2 1x2 3.250 6.500 1.250
S7IMPS-1.5X2 1-1/2 x 2 3.250 6.500 1.500
BPE TABLE DT-4.1.2-11

17
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
CROSSES BPE FITTINGS

S9MP - CROSS, CLAMP ENDS

PART NUMBER SIZE A B

S9MP-.50 1/2 2.375 4.750
S9MP-.75 3/4 2.500 5.000
S9MP-1 1 2.625 5.250
S9MP-1.5 1-1/2 2.875 5.750
S9MP-2 2 3.375 6.750
S9MP-2.5 2-1/2 3.625 7.250
S9MP-3 3 3.875 7.750
S9MP-4 4 4.750 9.500
BPE TABLE DT-4.1.2-4

S9WWWW - CROSS, TANGENT WELD ENDS

PART NUMBER SIZE A B

S9WWWW-.50 1/2 1.875 3.750
S9WWWW-.75 3/4 2.000 4.000
S9WWWW-1 1 2.125 4.250
S9WWWW-1.5 1-1/2 2.375 4.750
S9WWWW-2 2 2.875 5.750
S9WWWW-2.5 2-1/2 3.125 6.250
S9WWWW-3 3 3.375 6.750
S9WWWW-4 4 4.125 8.250
BPE TABLE DT-4.1.2-1

18 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS CROSSES

S9RWWWW - REDUCING CROSS, TANGENT WELD ENDS

PART NUMBER SIZE A B C D

S9RWWWW-.75X.50 3/4 X 1/2 2.000 4.000 2.000 4.000

S9RWWWW-1X.50 1 X 1/2 2.125 4.250 2.125 4.250
S9RWWWW-1X.75 1 X 3/4 2.125 4.250 2.125 4.250
S9RWWWW-1.5X.50 1-1/2 X 1/2 2.375 4.750 2.375 4.750
S9RWWWW-1.5X.75 1-1/2 X 3/4 2.375 4.750 2.375 4.750
S9RWWWW-1.5X1 1-1/2 X 1 2.375 4.750 2.375 4.750
S9RWWWW-2X.50 2 X 1/2 2.875 5.750 2.625 5.250
S9RWWWW-2X.75 2 X 3/4 2.875 5.750 2.625 5.250
S9RWWWW-2X1 2X1 2.875 5.750 2.625 5.250
S9RWWWW-2X1.5 2 X 1-1/2 2.875 5.750 2.625 5.250
S9RWWWW-2.5X1 2-1/2 X 1 3.125 6.250 2.875 5.750
S9RWWWW-2.5X1.5 2-1/2 X 1-1/2 3.125 6.250 2.875 5.750
S9RWWWW-2.5X2 2-1/2 X 2 3.125 6.250 2.875 5.750
S9RWWWW-3X1 3X1 3.375 6.750 3.125 6.250
S9RWWWW-3X1.5 3 X 1-1/2 3.375 6.750 3.125 6.250
S9RWWWW-3X2 3X2 3.375 6.750 3.125 6.250
S9RWWWW-3X2.5 3 X 2-1/2 3.375 6.750 3.125 6.250
S9RWWWW-4X1 4X1 4.125 8.250 3.625 7.250
S9RWWWW-4X1.5 4 X 1-1/2 4.125 8.250 3.625 7.250
S9RWWWW-4X2 4X2 4.125 8.250 3.875 7.750
S9RWWWW-4X2.5 4 X 2-1/2 4.125 8.250 3.875 7.750
S9RWWWW-4X3 4X3 4.125 8.250 3.875 7.750
S9RWWWW-6X3 6X3 5.625 11.250 4.875 9.750
S9RWWWW-6X4 6X4 5.625 11.250 5.125 10.250

19
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
REDUCERS BPE FITTINGS

S31S - SHORT CONCENTRIC REDUCER, WELD ENDS

PART NUMBER SIZE A B (min.) C (min.)

S31S-.75X.50 3/4 X 1/2 2.125 1.000 1.000

S31S-1X.50 1 X 1/2 2.500 1.000 1.000
S31S-1X.75 1 X 3/4 2.125 1.000 1.000
S31S-1.5X.75 1-1/2 X 3/4 3.000 1.000 1.000
S31S-1.5X1 1-1/2 X 1 2.500 1.000 1.000
S31S-2X1 2X1 3.375 1.000 1.000
S31S-2X1.5 2 X 1-1/2 2.500 1.000 1.000
S31S-2.5X1.5 2-1/2 X 1-1/2 3.375 1.000 1.000
S31S-2.5X2 2-1/2 X 2 2.500 1.000 1.000
S31S-3X1.5 3 X 1-1/2 4.250 1.500 1.000
S31S-3X2 3X2 3.375 1.500 1.000
S31S-3X2.5 3 X 2-1/2 2.625 1.500 1.000
S31S-4X2 4X2 5.125 1.500 1.000
S31S-4X2.5 4 X 2-1/2 4.250 1.500 1.000
S31S-4X3 4X3 3.875 1.500 1.500
S31S-6X3 6X3 7.250 2.000 1.500
S31S-6X4 6X4 5.625 2.000 1.500
BPE TABLE DT-4.1.3-1

20 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS REDUCERS

S32S - SHORT ECCENTRIC REDUCER, WELD ENDS

PART NUMBER SIZE A B (min.) C (min.)

S32S-.75X.50 3/4 X 1/2 2.125 1.000 1.000

S32S-1X.50 1 X 1/2 2.500 1.000 1.000
S32S-1X.75 1 X 3/4 2.125 1.000 1.000
S32S-1.5X.75 1-1/2 X 3/4 3.000 1.000 1.000
S32S-1.5X1 1-1/2 X 1 2.500 1.000 1.000
S32S-2X1 2X1 3.375 1.000 1.000
S32S-2X1.5 2 X 1-1/2 2.500 1.000 1.000
S32S-2.5X1.5 2-1/2 X 1-1/2 3.375 1.000 1.000
S32S-2.5X2 2-1/2 X 2 2.500 1.000 1.000
S32S-3X1.5 3 X 1-1/2 4.250 1.500 1.000
S32S-3X2 3X2 3.375 1.500 1.000
S32S-3X2.5 3 X 2-1/2 2.625 1.500 1.000
S32S-4X2 4X2 5.125 1.500 1.000
S32S-4X2.5 4 X 2-1/2 4.250 1.500 1.000
S32S-4X3 4X3 3.875 1.500 1.500
S32S-6X3 6X3 7.250 2.000 1.500
S32S-6X4 6X4 5.625 2.000 1.500
BPE TABLE DT-4.1.3-1

21
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
REDUCERS BPE FITTINGS

S31SK - SHORT CONCENTRIC REDUCER, CLAMP x WELD END

PART NUMBER SIZE A B (I.D.) C (min.)

(min.)
S31SK-.75X.50 3/4 X 1/2 2.625 .375 1.000
S31SK-1X.50 1 X 1/2 3.000 .375 1.000
S31SK-1X.75 1 X 3/4 2.625 .375 1.000
S31SK-1.5X.75 1-1/2 X 3/4 3.500 .375 1.000
S31SK-1.5X1 1-1/2 X 1 3.000 .375 1.000
S31SK-2X1 2X1 3.875 .375 1.000
S31SK-2X1.5 2 X 1-1/2 3.000 .375 1.000
S31SK-2.5X1.5 2-1/2 X 1-1/2 3.875 .375 1.000
S31SK-2.5X2 2-1/2 X 2 3.000 .375 1.000
S31SK-3X1.5 3 X 1-1/2 4.750 .375 1.000
S31SK-3X2 3X2 3.875 .375 1.000
S31SK-3X2.5 3 X 2-1/2 3.125 .375 1.000
S31SK-4X2 4X2 5.750 .375 1.000
S31SK-4X2.5 4 X 2-1/2 4.875 .375 1.000
S31SK-4X3 4X3 4.500 .375 1.500
S31SK-6X3 6X3 8.000 .375 1.500
S31SK-6X4 6X4 6.375 .375 1.500
BPE TABLE DT-4.1.3-2

22 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS REDUCERS

S32SK - SHORT ECCENTRIC REDUCER, CLAMP x WELD END

PART NUMBER SIZE A B (I.D.) C (min.)

(min.)
S32SK-.75X.50 3/4 X 1/2 2.625 .375 1.000
S32SK-1X.50 1 X 1/2 3.000 .375 1.000
S32SK-1X.75 1 X 3/4 2.625 .375 1.000
S32SK-1.5X.75 1-1/2 X 3/4 3.500 .375 1.000
S32SK-1.5X1 1-1/2 X 1 3.000 .375 1.000
S32SK-2X1 2X1 3.875 .375 1.000
S32SK-2X1.5 2 X 1-1/2 3.000 .375 1.000
S32SK-2.5X1.5 2-1/2 X 1-1/2 3.875 .375 1.000
S32SK-2.5X2 2-1/2 X 2 3.000 .375 1.000
S32SK-3X1.5 3 X 1-1/2 4.750 .375 1.000
S32SK-3X2 3X2 3.875 .375 1.000
S32SK-3X2.5 3 X 2-1/2 3.125 .375 1.000
S32SK-4X2 4X2 5.750 .375 1.000
S32SK-4X2.5 4 X 2-1/2 4.875 .375 1.000
S32SK-4X3 4X3 4.500 .375 1.500
S32SK-6X3 6X3 8.000 .375 1.500
S32SK-6X4 6X4 6.375 .375 1.500
BPE TABLE DT-4.1.3-2

23
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
REDUCERS BPE FITTINGS

S31S-14MP - SHORT CONCENTRIC REDUCER, CLAMP x CLAMP

PART NUMBER SIZE A B (I.D.) C (I.D.)

(min.) (min.)
S31S-14MP-.75X.50 3/4 X 1/2 3.125 .375 1.125
S31S-14MP-1X.50 1 X 1/2 3.500 .375 1.125
S31S-14MP-1X.75 1 X 3/4 3.125 .375 1.125
S31S-14MP-1.5X.75 1-1/2 X 3/4 4.000 .375 1.125
S31S-14MP-1.5X1 1-1/2 X 1 3.500 .375 1.125
S31S-14MP-2X1 2X1 4.375 .375 1.125
S31S-14MP-2X1.5 2 X 1-1/2 3.500 .375 1.125
S31S-14MP-2.5X1.5 2-1/2 X 1-1/2 4.375 .375 1.125
S31S-14MP-2.5X2 2-1/2 X 2 3.500 .375 1.125
S31S-14MP-3X1.5 3 X 1-1/2 5.250 .375 1.125
S31S-14MP-3X2 3X2 4.375 .375 1.125
S31S-14MP-3X2.5 3 X 2-1/2 3.625 .375 1.125
S31S-14MP-4X2 4X2 6.250 .375 1.125
S31S-14MP-4X2.5 4 X 2-1/2 5.375 .375 1.125
S31S-14MP-4X3 4X3 5.000 .375 1.625
S31S-14MP-6X3 6X3 8.500 .375 1.625
S31S-14MP-6X4 6X4 7.000 .375 1.625
BPE TABLE DT-4.1.3-3

24 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS REDUCERS

S32S-14MP - SHORT ECCENTRIC REDUCER, CLAMP x CLAMP

PART NUMBER SIZE A B (I.D.) C (I.D.)

(min.) (min.)
S32S-14MP-.75X.50 3/4 X 1/2 3.125 .375 1.125
S32S-14MP-1X.50 1 X 1/2 3.500 .375 1.125
S32S-14MP-1X.75 1 X 3/4 3.125 .375 1.125
S32S-14MP-1.5X.75 1-1/2 X 3/4 4.000 .375 1.125
S32S-14MP-1.5X1 1-1/2 X 1 3.500 .375 1.125
S32S-14MP-2X1 2X1 4.375 .375 1.125
S32S-14MP-2X1.5 2 X 1-1/2 3.500 .375 1.125
S32S-14MP-2.5X1.5 2-1/2 X 1-1/2 4.375 .375 1.125
S32S-14MP-2.5X2 2-1/2 X 2 3.500 .375 1.125
S32S-14MP-3X1.5 3 X 1-1/2 5.250 .375 1.125
S32S-14MP-3X2 3X2 4.375 .375 1.125
S32S-14MP-3X2.5 3 X 2-1/2 3.625 .375 1.125
S32S-14MP-4X2 4X2 6.250 .375 1.125
S32S-14MP-4X2.5 4 X 2-1/2 5.375 .375 1.125
S32S-14MP-4X3 4X3 5.000 .375 1.625
S32S-14MP-6X3 6X3 8.500 .375 1.625
S32S-14MP-6X4 6X4 7.000 .375 1.625
BPE TABLE DT-4.1.3-3

25
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
REDUCERS BPE FITTINGS

S31 - CONCENTRIC REDUCER, TANGENT WELD ENDS

PART NUMBER SIZE A

S31-.75X.50 3/4 X 1/2 4.000

S31-1X.50 1 X 1/2 4.500
S31-1X.75 1 X 3/4 4.000
S31-1.5X.50 1-1/2 X 1/2 5.500
S31-1.5X.75 1-1/2 X 3/4 5.000
S31-1.5X1 1-1/2 X 1 5.000
S31-2X.50 2 X 1/2 7.750
S31-2X.75 2 X 3/4 7.250
S31-2X1 2X1 7.250
S31-2X1.5 2 X 1-1/2 5.250
S31-2.5X.50 2-1/2 X 1/2 9.750
S31-2.5X.75 2-1/2 X 3/4 9.250
S31-2.5X1 2-1/2 X 1 9.250
S31-2.5X1.5 2-1/2 X 1-1/2 7.250
S31-2.5X2 2-1/2 X 2 5.500
S31-3X.50 3 X 1/2 12.750
S31-3X.75 3 X 3/4 11.250
S31-3X1 3X1 11.250
S31-3X1.5 3 X 1-1/2 9.250
S31-3X2 3X2 7.500
S31-3X2.5 3 X 2-1/2 5.500
S31-4X1 4X1 15.500
S31-4X1.5 4 X 1-1/2 13.500
S31-4X2 4X2 11.750
S31-4X2.5 4 X 2-1/2 9.750
S31-4X3 4X3 7.750
S31-6X3 6X3 10.000
S31-6X4 6X4 10.000

Per ASME BPE-2012

26 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS REDUCERS

S32 - ECCENTRIC REDUCER, TANGENT WELD ENDS

PART NUMBER SIZE A

S32-.75X.50 3/4 X 1/2 4.000

S32-1X.50 1 X 1/2 4.500
S32-1X.75 1 X 3/4 4.000
S32-1.5X.50 1-1/2 X 1/2 5.500
S32-1.5X.75 1-1/2 X 3/4 5.000
S32-1.5X1 1-1/2 X 1 5.000
S32-2X.50 2 X 1/2 7.750
S32-2X.75 2 X 3/4 7.250
S32-2X1 2X1 7.250
S32-2X1.5 2 X 1-1/2 5.250
S32-2.5X.50 2-1/2 X 1/2 9.750
S32-2.5X.75 2-1/2 X 3/4 9.250
S32-2.5X1 2-1/2 X 1 9.250
S32-2.5X1.5 2-1/2 X 1-1/2 7.250
S32-2.5X2 2-1/2 X 2 5.500
S32-3X.50 3 X 1/2 11.750
S32-3X.75 3 X 3/4 11.250
S32-3X1 3X1 11.250
S32-3X1.5 3 X 1-1/2 9.250
S32-3X2 3X2 7.500
S32-3X2.5 3 X 2-1/2 5.500
S32-4X1 4X1 15.500
S32-4X1.5 4 X 1-1/2 13.500
S32-4X2 4X2 11.750
S32-4X2.5 4 X 2-1/2 9.750
S32-4X3 4X3 7.750
S32-6X3 6X3 9.750
S32-6X4 6X4 10.000

Per ASME BPE-2012

27
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
REDUCERS BPE FITTINGS

S31K - CONCENTRIC REDUCER, CLAMP x TANGENT WELD END

PART NUMBER SIZE A

S31K-.75X.50 3/4 X 1/2 3.000

S31K-1X.50 1 X 1/2 3.500
S31K-1X.75 1 X 3/4 3.000
S31K-1.5X.50 1-1/2 X 1/2 4.500
S31K-1.5X.75 1-1/2 X 3/4 4.000
S31K-1.5X1 1-1/2 X 1 4.000
S31K-2X.50 2 X 1/2 6.500
S31K-2X.75 2 X 3/4 6.000
S31K-2X1 2X1 6.000
S31K-2X1.5 2 X 1-1/2 4.000
S31K-2.5X.50 2-1/2 X 1/2 8.500
S31K-2.5X.75 2-1/2 X 3/4 9.000
S31K-2.5X1 2-1/2 X 1 8.000
S31K-2.5X1.5 2-1/2 X 1-1/2 6.000
S31K-2.5X2 2-1/2 X 2 4.250
S31K-3X.50 3 X 1/2 12.000
S31K-3X.75 3 X 3/4 11.000
S31K-3X1 3X1 10.000
S31K-3X1.5 3 X 1-1/2 8.000
S31K-3X2 3X2 6.250
S31K-3X2.5 3 X 2-1/2 4.250
S31K-4X1 4X1 14.125
S31K-4X1.5 4 X 1-1/2 12.125
S31K-4X2 4X2 10.375
S31K-4X2.5 4 X 2-1/2 8.375
S31K-4X3 4X3 6.375
S31K-6X3 6X3 9.000
S31K-6X4 6X4 9.000

Per ASME BPE-2012

28 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS REDUCERS

S32K - ECCENTRIC REDUCER, CLAMP x TANGENT WELD END

PART NUMBER SIZE A

S32K-.75X.50 3/4 X 1/2 3.000

S32K-1X.50 1 X 1/2 3.500
S32K-1X.75 1 X 3/4 3.000
S32K-1.5X.50 1-1/2 X 1/2 4.500
S32K-1.5X.75 1-1/2 X 3/4 4.000
S32K-1.5X1 1-1/2 X 1 4.000
S32K-2X.50 2 X 1/2 6.500
S32K-2X.75 2 X 3/4 6.000
S32K-2X1 2X1 6.000
S32K-2X1.5 2 X 1-1/2 4.000
S32K-2.5X.50 2-1/2 X 1/2 9.500
S32K-2.5X.75 2-1/2 X 3/4 9.000
S32K-2.5X1 2-1/2 X 1 8.000
S32K-2.5X1.5 2-1/2 X 1-1/2 6.000
S32K-2.5X2 2-1/2 X 2 4.250
S32K-3X.50 3 X 1/2 12.000
S32K-3X.75 3 X 3/4 11.000
S32K-3X1 3X1 10.000
S32K-3X1.5 3 X 1-1/2 8.000
S32K-3X2 3X2 6.250
S32K-3X2.5 3 X 2-1/2 4.250
S32K-4X1 4X1 14.125
S32K-4X1.5 4 X 1-1/2 12.125
S32K-4X2 4X2 10.375
S32K-4X2.5 4 X 2-1/2 8.375
S32K-4X3 4X3 6.375
S32K-6X3 6X3 8.750
S32K-6X4 6X4 9.000

Per ASME BPE-2012

29
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
REDUCERS BPE FITTINGS

S31-14MP - CONCENTRIC REDUCER, CLAMP ENDS

PART NUMBER SIZE A

S31-14MP-.75X.50 3/4 X 1/2 2.000

S31-14MP-1X.50 1 X 1/2 2.500
S31-14MP-1X.75 1 X 3/4 2.000
S31-14MP-1.5X.50 1-1/2 X 1/2 3.500
S31-14MP-1.5X.75 1-1/2 X 3/4 3.000
S31-14MP-1.5X1 1-1/2 X 1 3.000
S31-14MP-2X.50 2 X 1/2 7.000
S31-14MP-2X.75 2 X 3/4 6.000
S31-14MP-2X1 2X1 5.000
S31-14MP-2X1.5 2 X 1-1/2 3.000
S31-14MP-2.5X.50 2-1/2 X 1/2 9.000
S31-14MP-2.5X.75 2-1/2 X 3/4 8.000
S31-14MP-2.5X1 2-1/2 X 1 7.000
S31-14MP-2.5X1.5 2-1/2 X 1-1/2 5.000
S31-14MP-2.5X2 2-1/2 X 2 3.000
S31-14MP-3X.50 3 X 1/2 11.000
S31-14MP-3X.75 3 X 3/4 10.000
S31-14MP-3X1 3X1 9.000
S31-14MP-3X1.5 3 X 1-1/2 7.000
S31-14MP-3X2 3X2 5.000
S31-14MP-3X2.5 3 X 2-1/2 3.000
S31-14MP-4X1 4X1 13.125
S31-14MP-4X1.5 4 X 1-1/2 11.125
S31-14MP-4X2 4X2 9.125
S31-14MP-4X2.5 4 X 2-1/2 7.125
S31-14MP-4X3 4X3 5.125
S31-14MP-6X3 6X3 7.625
S31-14MP-6X4 6X4 7.625

Per ASME BPE-2012

30 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS BOTTOM OUTLET USE POINT

S32-14MP - ECCENTRIC REDUCER, CLAMP ENDS

PART NUMBER SIZE A

S32-14MP-.75X.50 3/4 X 1/2 2.000

S32-14MP-1X.50 1 X 1/2 2.500
S32-14MP-1X.75 1 X 3/4 2.000
S32-14MP-1.5X.50 1-1/2 X 1/2 3.500
S32-14MP-1.5X.75 1-1/2 X 3/4 3.000
S32-14MP-1.5X1 1-1/2 X 1 3.000
S32-14MP-2X.50 2 X 1/2 6.500
S32-14MP-2X.75 2 X 3/4 6.000
S32-14MP-2X1 2X1 5.000
S32-14MP-2X1.5 2 X 1-1/2 3.000
S32-14MP-2.5X.50 2-1/2 X 1/2 8.500
S32-14MP-2.5X.75 2-1/2 X 3/4 8.000
S32-14MP-2.5X1 2-1/2 X 1 7.000
S32-14MP-2.5X1.5 2-1/2 X 1-1/2 5.000
S32-14MP-2.5X2 2-1/2 X 2 3.000
S32-14MP-3X.50 3 X 1/2 10.500
S32-14MP-3X.75 3 X 3/4 10.000
S32-14MP-3X1 3X1 9.000
S32-14MP-3X1.5 3 X 1-1/2 7.000
S32-14MP-3X2 3X2 5.000
S32-14MP-3X2.5 3 X 2-1/2 3.000
S32-14MP-4X1 4X1 13.125
S32-14MP-4X1.5 4 X 1-1/2 11.125
S32-14MP-4X2 4X2 9.125
S32-14MP-4X2.5 4 X 2-1/2 7.125
S32-14MP-4X3 4X3 5.125
S32-14MP-6X3 6X3 7.500
S32-14MP-6X4 6X4 7.625

Per ASME BPE-2012

31
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BOTTOM OUTLET USE POINT BPE FITTINGS

S2UBWWK - BOTTOM OUTLET USE POINT

PART NUMBER SIZE A B C D

S2UBWWK-.75X.50 3/4 X 1/2 4.500 2.250 3.750 .875

S2UBWWK-1X.50 1 X 1/2 3.000 1.500 3.000 1.125
S2UBWWK-1X.75 1 X 3/4 3.000 1.500 3.000 1.125
S2UBWWK-1.5X.50 1-1/2 X 1/2 4.500 2.250 4.500 1.375
S2UBWWK-1.5X.75 1-1/2 X 3/4 4.500 2.250 4.500 1.375
S2UBWWK-1.5X1 1-1/2 X 1 4.500 2.250 4.500 1.375
S2UBWWK-2X.50 2 X 1/2 6.000 3.000 5.000 1.625
S2UBWWK-2X.75 2 X 3/4 6.000 3.000 5.000 1.625
S2UBWWK-2X1 2X1 6.000 3.000 5.000 1.625
S2UBWWK-2X1.5 2 X 1-1/2 6.000 3.000 5.000 1.625
S2UBWWK-2.5X.50 2-1/2 X 1/2 7.500 3.750 5.750 1.875
S2UBWWK-2.5X.75 2-1/2 X 3/4 7.500 3.750 5.750 1.875
S2UBWWK-2.5X1 2-1/2 X 1 7.500 3.750 5.750 1.875
S2UBWWK-2.5X1.5 2-1/2 X 1-1/2 7.500 3.750 5.750 1.875
S2UBWWK-2.5X2 2-1/2 X 2 7.500 3.750 5.750 1.875
S2UBWWK-3X.50 3 X 1/2 9.000 4.500 6.500 2.125
S2UBWWK-3X.75 3 X 3/4 9.000 4.500 6.500 2.125
S2UBWWK-3X1 3X1 9.000 4.500 6.500 2.125
S2UBWWK-3X1.5 3 X 1-1/2 9.000 4.500 6.500 2.125
S2UBWWK-3X2 3X2 9.000 4.500 6.500 2.125
S2UBWWK-3X2.5 3 X 2-1/2 9.000 4.500 6.500 2.125
S2UBWWK-4X.50 4 X 1/2 12.000 6.000 8.500 2.625
S2UBWWK-4X.75 4 X 3/4 12.000 6.000 8.500 2.625
S2UBWWK-4X1 4X1 12.000 6.000 8.500 2.625
S2UBWWK-4X1.5 4 X 1-1/2 12.000 6.000 8.500 2.625
S2UBWWK-4X2 4X2 12.000 6.000 8.500 2.625
S2UBWWK-4X2.5 4 X 2-1/2 12.000 6.000 8.500 2.625
S2UBWWK-4X3 4X3 12.000 6.000 8.500 2.625
ALSO AVAILABLE WITH BUTT-WELD OUTLET

32 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS SIDE OUTLET USE POINT

S2USWWK - SIDE OUTLET USE POINT

PART NUMBER SIZE A B C D E

S2USWWK -.75X.50 3/4 X 1/2 4.500 2.250 3.750 3.875 .875

S2USWWK-1X.50 1 X 1/2 3.000 1.500 3.000 3.250 1.125
S2USWWK-1X.75 1 X 3/4 3.000 1.500 3.000 3.125 1.125
S2USWWK-1.5X.50 1-1/2 X 1/2 4.500 2.250 4.500 5.000 1.375
S2USWWK-1.5X.75 1-1/2 X 3/4 4.500 2.250 4.500 4.875 1.375
S2USWWK-1.5X1 1-1/2 X 1 4.500 2.250 4.500 4.750 1.375
S2USWWK-2X.50 2 X 1/2 6.000 3.000 5.000 5.750 1.625
S2USWWK-2X.75 2 X 3/4 6.000 3.000 5.000 5.625 1.625
S2USWWK-2X1 2X1 6.000 3.000 5.000 5.500 1.625
S2USWWK-2X1.5 2 X 1-1/2 6.000 3.000 5.000 5.250 1.625
S2USWWK-2.5X.50 2-1/2 X 1/2 7.500 3.750 5.750 6.750 1.875
S2USWWK-2.5X.75 2-1/2 X 3/4 7.500 3.750 5.750 6.625 1.875
S2USWWK-2.5X1 2-1/2 X 1 7.500 3.750 5.750 6.500 1.875
S2USWWK-2.5X1.5 2-1/2 X 1-1/2 7.500 3.750 5.750 6.250 1.875
S2USWWK-2.5X2 2-1/2 X 2 7.500 3.750 5.750 6.000 1.875
S2USWWK-3X.50 3 X 1/2 9.000 4.500 6.500 7.750 2.125
S2USWWK-3X.75 3 X 3/4 9.000 4.500 6.500 7.625 2.125
S2USWWK-3X1 3X1 9.000 4.500 6.500 7.500 2.125
S2USWWK-3X1.5 3 X 1-1/2 9.000 4.500 6.500 7.250 2.125
S2USWWK-3X2 3X2 9.000 4.500 6.500 7.000 2.125
S2USWWK-3X2.5 3 X 2-1/2 9.000 4.500 6.500 6.750 2.125
S2USWWK-4X.50 4 X 1/2 12.000 6.000 8.500 10.250 2.625
S2USWWK-4X.75 4 X 3/4 12.000 6.000 8.500 10.125 2.625
S2USWWK-4X1 4X1 12.000 6.000 8.500 10.000 2.625
S2USWWK-4X1.5 4 X 1-1/2 12.000 6.000 8.500 9.750 2.625
S2USWWK-4X2 4X2 12.000 6.000 8.500 9.500 2.625
S2USWWK-4X2.5 4 X 2-1/2 12.000 6.000 8.500 9.250 2.625
S2USWWK-4X3 4X3 12.000 6.000 8.500 9.000 2.625
ALSO AVAILABLE WITH BUTT-WELD OUTLET

33
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
STUB ENDS BPE FITTINGS

S14WA - STUB END - TYPE A

PART NUMBER SIZE A B C

S14WA-.50 1/2 2.750 1.500 .130
S14WA-.75 3/4 2.750 1.500 .130
S14WA-1 1 2.750 2.000 .130
S14WA-1.5 1-1/2 2.750 2.875 .130
S14WA-2 2 2.750 3.625 .130
S14WA-2.5 2-1/2 2.750 4.125 .130
S14WA-3 3 2.750 5.000 .166
S14WA-4 4 2.750 6.187 .166
S14WA-6 6 3.000 8.500 .218
STUB END FACE IS SERRATED

34 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS FERRULES

STL14AM7 - LONG WELD FERRULE

PART NUMBER SIZE A

STL14AM7-.50 1/2 1.750
STL14AM7-.75 3/4 1.750
STL14AM7-1A 1 (TYPE A) 1.750
STL14AM7-1 1 1.750
STL14AM7-1.5 1-1/2 1.750
STL14AM7-2 2 2.250
STL14AM7-2.5 2-1/2 2.250
STL14AM7-3 3 2.250
STL14AM7-4 4 2.250
STL14AM7-6 6 3.000
BPE TABLE DT-4.1.4-1

SL14AM7 - MEDIUM WELD FERRULE

PART NUMBER SIZE A

SL14AM7-.50 1/2 1.125
SL14AM7-.75 3/4 1.125
SL14AM7-1 1 1.125
S14AM7-1.5 1-1/2 1.125
S14AM7-2 2 1.125
S14AM7-2.5 2-1/2 1.125
S14AM7-3 3 1.125
S14AM7-4 4 1.125
BPE TABLE DT-4.1.4-1

S14WMP - SHORT WELD FERRULE

PART NUMBER SIZE A

S14WMP-.50 1/2" .500
S14WMP-.75 3/4” .500
S14WMP-1 1" .500
S14WMP-1.5 1-1/2 .500
S14WMP-2 2 .500
S14WMP-2.5 2-1/2 .500
S14WMP-3 3 .500
S14WMP-4 4 .625
BPE TABLE DT-4.1.4-1

35
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
CAPS BPE FITTINGS

S16W - LONG TANGENT WELD CAP

PART NUMBER SIZE A
S16W-.50 1/2 1.500
S16W-.75 3/4 1.500
S16W-1 1 1.629
S16W-1.5 1-1/2 1.660
S16W-2 2 1.762
S16W-2.5 2-1/2 1.505
S16W-3 3 1.750
S16W-4 4 2.000
S16W-6 6 2.500
BPE TABLE DT-4.1.5-1
“A” DIMENSION IS STRAIGHT TANGENT LENGTH
“B” MINIMUM I.D. STRAIGHT LENGTH = .375 ALL SIZES

S16AMP - CLAMP CAP

PART NUMBER SIZE A B

S16AMP-.50 1/2" & 3/4" .187 .984
S16AMP-1 1" & 1-1/2" .250 1.984
S16AMP-2 2" .250 2.516
S16AMP-2.5 2-1/2 .250 3.047
S16AMP-3 3 .250 3.579
S16AMP-4 4 .312 4.682
S16AMP-6 6 .437 6.570
BPE TABLE DT-4.1.5-2

36 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS CLAMPS

13MHHM - SINGLE PIN CLAMP

PART NUMBER SIZE A PSI RATING @ PSI RATING @

70°F 250°F
13MHHM-.50 1/2 & 3/4 1.125 1500 1200
13MHHM-1 1 & 1-1/2 2.122 500 300
13MHHM-2 2 2.654 450 300
13MHHM-2.5 2-1/2 3.185 400 200
13MHHM-3 3 3.717 350 195
13MHHM-4 4 4.820 300 150
13MHHM-5 5 5.625 150 75
13MHHM-6 6 6.695 150 75
13MHHM-8 8 8.695 100 50
13MHHM-10 10 10.695 75 40
13MHHM-12 12 12.695 50 25
NOTES: ALSO AVAILABLE WITH ROCKET WING NUT
AVAILABLE IN 304 OR 316 MATERIAL
PRESSURE RATINGS ARE MAXIMUM WORKING PRESSURE ONLY
PRESSURE RATINGS PERTAIN TO THE CLAMP “UNION”

13MHHM-DP - DOUBLE PIN CLAMP

PART NUMBER SIZE A PSI RATING @ PSI RATING @
70°F 250°F
13MHHM-DP-.50 1/2 & 3/4 1.125 1500 1200
13MHHM-DP-1 1 & 1-1/2 2.122 500 300
13MHHM-DP-2 2 2.654 450 300
13MHHM-DP-2.5 2-1/2 3.185 400 200
13MHHM-DP-3 3 3.717 350 195
13MHHM-DP-4 4 4.820 300 150
13MHHM-DP-6 6 6.695 150 75
13MHHM-DP-8 8 8.695 100 50
13MHHM-DP-10 10 10.695 75 40
NOTES: ROCKET WING NUTS ALSO AVAILABLE
AVAILABLE IN 304 MATERIAL ONLY PRESSURE RATINGS ARE MAXIMUM WORKING PRESSURE ONLY
PRESSURE RATINGS PERTAIN TO THE CLAMP “UNION”

37
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
CLAMPS BPE FITTINGS

13MHP - HIGH PRESSURE CLAMP

PART NUMBER SIZE A PSI RATING @ PSI RATING @
70°F 250°F
13MHP-.50 1/2 & 3/4 1.125 1500 1200
13MHP-1 1 & 1-1/2 2.046 1000 800
13MHP-2 2 2.596 1000 800
13MHP-2.5 2-1/2 3.127 1000 800
13MHP-3 3 3.659 1000 800
13MHP-4 4 4.762 800 600
13MHP-5 5 5.762 300 200
13MHP-6 6 6.695 300 200
AVAILABLE IN 304 AND 316 MATERIAL 13MHP-8 8 8.695 250 150
13MHP-10 10 10.695 200 125
13MHP-12 12 12.695 150 100
NOTES: PRESSURE RATINGS ARE MAXIMUM WORKING PRESSURE ONLY
PRESSURE RATINGS PERTAIN TO THE CLAMP “UNION”
SUPPLIED WITH BRASS HEX NUTS

13MHHS - THREE SEGMENT CLAMP

PART NUMBER SIZE A PSI RATING PSI RATING

@ 70°F @ 250°F
13MHHS-1 1 & 1-1/2 2.122 600 300
13MHHS-2 2 2.654 550 275
13MHHS-2.5 2-1/2 3.185 450 225
13MHHS-3 3 3.717 350 175
13MHHS-4 4 4.820 300 150

NOTES: ROCKET WING NUTS ALSO AVAILABLE

PRESSURE RATINGS ARE MAXIMUM WORKING PRESSURE ONLY
PRESSURE RATINGS PERTAIN TO THE CLAMP “UNION”
AVAILABLE IN 304 MATERIAL ONLY

13ASME - ASME DOUBLE BOLT CLAMP

PART NUMBER SIZE A PSI RATING PSI RATING
@ 70°F @ 250°F
13ASME-1 1 & 1-1/2 2.046 1485 1337
13ASME-2 2 2.578 1370 1233
13AMSE-3 3 3.640 1000 900
13ASME-4 4 4.744 874 787
13ASME-6 6 6.632 415 374
13ASME-8 8 8.632 299 269
13ASME-10 10 10.632 161 145
13ASME-12 12 12.632 102 92
AVAILABLE IN 316 MATERIAL ONLY
NOTE: TO MEET THE PSI RATINGS ABOVE THE FERRULE (HUB) USED
SHALL BE DESIGNED IN ACCORDANCE WITH ASME SECTION 8
DIVISION 1 MANDATORY APPENDIX 24
STANDARD FERRULES AND FULL FACE GASKET CAN BE USED
HOWEVER PERFORMANCE MAY NOT MEET THE ABOVE RATINGS

38 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
 BPE FITTINGS GASKETS

CLAMP GASKET PERFORMANCE CHART

PROPERTY BUNA-N EPDM TEFLON VITON SILICONE
TENSILE STRENGTH GOOD GOOD - EXCELLENT EXCELLENT EXCELLENT GOOD
ELECTRICAL PROPERTIES POOR EXCELLENT EXCELLENT GOOD EXCELLENT
WEATHER RESISTANCE GOOD EXCELLENT EXCELLENT EXCELLENT EXCELLENT
OZONE RESISTANCE POOR EXCELLENT EXCELLENT EXCELLENT EXCELLENT
HEAT RESISTANCE GOOD (250°F) EXCELLENT (300°F) EXCELLENT (500°F) EXCELLENT (400°F) EXCELLENT (450°F)
COLD RESISTANCE GOOD (-30°F) GOOD - EXCELLENT EXCELLENT (-100°F) GOOD (-30°F) EXCELLENT (-40°F)
(-20°F)
STEAM RESISTANCE EXCELLENT EXCELLENT EXCELLENT EXCELLENT GOOD
TEAR RESISTANCE GOOD GOOD EXCELLENT GOOD GOOD
ABRASION RESISTANCE GOOD GOOD EXCELLENT GOOD GOOD
ACID RESISTANCE POOR - GOOD GOOD - EXCELLENT EXCELLENT GOOD GOOD
PETROLEUM OIL EXCELLENT POOR EXCELLENT EXCELLENT POOR - GOOD
FLAME RESISTANCE POOR POOR EXCELLENT GOOD POOR
VEGETABLE OIL EXCELLENT GOOD EXCELLENT EXCELLENT GOOD (INTERMITTENT)
USP CLASS VI NO YES YES YES YES
ANIMAL OILS & FATS EXCELLENT POOR EXCELLENT EXCELLENT GOOD
ALCOHOL, GLYCOLS EXCELLENT EXCELLENT EXCELLENT GOOD EXCELLENT
SOAPS, BLEACHES, POOR EXCELLENT EXCELLENT GOOD POOR
DETERGENTS

THE ABOVE CHART IS INTENDED AS A GUIDLINE, ACUTAL PERFORMANCE MAY VARY WITH EACH APPLICATION.

40MP - CLAMP GASKET

PART NUMBER SIZE

40MP-.50 1/2
40MP-.75 3/4
40MP-1 1
40MP-1.5 1-1/2
40MP-2 2
40MP-2.5 2-1/2
40MP-3 3
40MP-4 4
40MP-5 5
AVAILABLE IN THE FOLLOWING MATERIALS:
BUNA-N, EPDM, TEFLON, VITON, SILICONE 40MP-6 6
TUF-STEEL & STAINLESS 40MP-8 8
OTHER MATERIALS AVAILABLE UPON REQUEST
40MP-10 10
40MP-12 12

39
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE-TUBING BPE FITTINGS

ASTM-A270 BPE TUBING

• Tubing is made from 316L material and is 100% boroscoped.
• Mechanically polished on both I.D. and O.D. (20Ra I.D., 32Ra O.D.)
Also Available with 15Ra EP I.D., 32Ra O.D. finish
Surface finish measured per ASME/ANSI B46.1
• Tubing is tested beyond the requirements of ASTM A269 and A270
by mechanically testing to ASME SA249 specifications.
• Tubing is bright annealed in line to 1900°F
• High purity tubing is also available which can include cleaned for gas/oxygen service, thermocouple
cleaning or nitric acid cleaning with a deionized water rinse.
• High purity tubing is cleaned and packaged in a Class 100 Cleanroom.
Tubing Tolerances
PART OD SIZE WALL OD WALL LENGTH BOX QTY.
NUMBER (IN.) (IN.) TOLERANCE TOLERANCE TOLERANCE (FT.)

SAN00507 .500 .065 +.005 / -.005 .065 ± 10% + .125 / -.000 300
SAN00757 .750 .065 +.005 / -.005 .065 ± 10% + .125 / -.000 300
SAN01007 1.000 .065 +.005 / -.005 .065 ± 10% + .125 / -.000 300
SAN01507 1.500 .065 +.008 / -.008 .065 ± 10% + .125 / -.000 300
SAN02007 2.000 .065 +.008 / -.008 .065 ± 10% + .125 / -.000 300
SAN02507 2.500 .065 +.010 / -.010 .065 ± 10% + .125 / -.000 200
SAN03007 3.000 .065 +.010 / -.010 .065 ± 10% + .125 / -.000 200
SAN04007 4.000 .083 +.015 / -.015 .083 ± 10% + .125 / -.000 100
SAN06007 6.000 .109 +.030 / -.030 .109 ± 10% + .188 / -.000 20

• Tubing available in numerous sizes and wall thicknesses not listed including rectangular shapes, call
for details and pricing.
• Surcharges apply at time of shipment.
Chemical Composition - 316L (%)
(C) Carbon, (Mn) Manganese, max (N) Nitrogen, (S) Sulfur (Ni) Nickel (Cr) Chromium (Mo) Molybdenum
max max

.030 2.00 .10 .005 - .017 10.0 - 14.0 16.0 - 18.0 2.0 - 3.0

40 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
BPE FITTINGS INDUSTRY CROSS REFERENCE

STEEL & O’BRIEN ALFA-LAVAL SPX VNE DIXON

S2S B2S S2S TE2S T2S

S2CKW B2CMW S2CKW TE2C T2CM
S2KS B2KS S2KS TE2KS T2KS
S2KKW B2KMW S2KKW TE2KC T2KM
S2CMP B2CMP S2CMP TEG2C T2CMP
S2KMP B2KMP S2KMP TEG2K T2KMP
S7WWW B7WWW S7WWW TE7WWW T7WWW
S7SWWK B7WWMS S7SWWK TE7WWCS T7WWMS
S7WWK B7WWM S7WWK TE7WWC T7WWM
S7WSKW B7WMSW S7WSKW TE7WCSW
S7MPS B7MPS S7MPS TEG7S T7MPS
S7MP B7MP S7MP TEG7 T7MP
S7RWWW B7RWWW S7RWWW TE7RWWW T7RWWW
S7RWWK B7RWWM S7RWWK TE7RWWC T7WWM
S7RSWWK B7RWWMS S7RSWWK TE7RWWCS T7RWWMS
S7RMP B7RMP S7RMP TEG7R T7RMP
S7RMPS B7RMPS S7RMPS TEG7RS T7RMPS
S7IWWKS B7IWWMS S7RSGT TE7IWWCS T7IWWMS
S7IMPS B7IMPS S7RSGTMP TEG7IS T7IMPS
S9MP B9MP S9MP TEG9
S9WWWW B9WWWW S9WWWW TE9WWWW
S9RWWWW B9RWWWW S9RWWWW TE9RWWWW
S31S TE31SWW
S32S TE32SWW
S31SK TE31SCW
S32SK TE32SCW
S31S-14MP TEG31SCC
S32S-14MP TEG32SCC
S31 B31 S31 TE31WW T31W
S32 B32 S32 TE32WW T32W
S31K B31M S31K TE31CW T31M
S32K B32M S32K TE32CW T32M
S31-14MP B31-14MP S31-14MP TEG31CC T3114MP
S32-14MP B32-14MP S32-14MP TEG32CC T3214MP
S2UBWWK B2UMPBOA S2UBWWK TE2UBWWW
S2USWWK B2UMPSOA S2USWWK TE2USWWC
STL14AM7 BS14AM S14AWF TEG14AM7 TL14AM7
S16W B16W S16AWF TE16W T16W
S16AMP 16AMP S16AMP TEG16A T16AMP
S14WA S14WA TE14WA T14VB

41
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
 BPE FITTINGS

GLOSSARY OF TERMS

Automatic weld Uses equipment which welds without the constant adjusting of controls by the welder or operator.
Equipment controls joint alignment by using an automatic sensing device.

Bioprocessing Specific process that uses complete living cells or their components (e.g., bacteria, enzymes,
chloroplasts) to obtain desired products.

Borescope An optical device consisting of a rigid or flexible tube with an eyepiece on one end, an objective
lens on the other, linked together by a relay optical system in between. Used for the inspection of
difficult access locations.

Clean-in-place (CIP) A method of cleaning the interior surfaces of pipes, vessels, process equipment, typically with acid,
caustic or a combination of both, without disassembly.

Compendial water Water that complies with USP and/or other acknowledged body related to the quality, manufacture
or distribution of high purity water.

Dead leg An area of entrapment in a vessel or piping run that could lead to contamination of the product.

Electropolishing An electrochemical process that removes material from a metallic workpiece. It is used to polish,
passivate, and deburr metal parts.

Fixture mark An area on an electropolished component where the electrical connection was made for processing
the component.

Full penetration weld A weld joint where the depth of the weld extends from its face into the weld joint so that the joint
is fully fused.

Gasket A static seal which fills the space between two or more mating surfaces, generally to prevent
leakage from or into the joined objects while under compression.

Heat number The identification number that is stamped on a material plate after it is removed from the ladle and
rolled at a steel mill.

Hydrotest A pressure test of vessels, piping or components performed by pressurizing the internal volume
with water at a pressure defined by applicable code.

Hygienic Term used to describe equipment and piping systems that, by their design, construction and
operation provide for cleanliness so that the products produced will not adversely affect human or
animal health.

42 7869 ROUTE 98 TEL: 585-492-5800

WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
 BPE FITTINGS

GLOSSARY OF TERMS

Lay One of the three components of surface finish. Lay is the direction of the predominant surface
pattern ordinarily determined by the production method used.

Manual welding Welding in which the entire welding operation is performed and controlled by hand.

Maximum working The temperature/pressure at which the system is capable of operating for a sustained period of
temperature/pressure time.

Mechanical seal A device used for sealing fluids with rotating shafts.

Orbital welding Automatic welding whereby the arc is rotated mechanically through 360° (180° in double up
welding) around a static work piece, an object such as a pipe, in a continuous process, with or
without filler material.

O-ring A static seal of circular cross section.

Passivation The removal of free iron from the surface of stainless steel by means of a chemical dissolution
usually by acid which enhance the formation of the passive layer.

Product contact surface Any surface that contacts raw materials, process materials and/or product.

Profilometer A measuring instrument used to measure a surface’s profile, in order to quantify its roughness.

Ra Log of the arithmetic mean of the surface profile.

Steam-in-place (SIP) The use of steam to sterilize a piece of equipment without the use of an autoclave.

Sterile Free from living organisms.

Surface finish The description of the surface expressed in Ra.

Validation Documented evidence that the system does what it purports to do.

WFI A classification of compendial water suitable for human injection.

43
7869 ROUTE 98 TEL: 585-492-5800
WWW.STEELOBRIEN.COM SALES@SOB.US
ARCADE, NY 14009
 OUR QUALITY POLICY

Steel & O’Brien Manufacturing is committed

to understanding the needs of our customers
and meeting or exceeding those requirements
through careful attention to detail and through the
continuous improvement of our processes.

We are dedicated to delivering defect-free

products on-time at the most competitive cost
possible through an effective Quality Management
System based on sound Quality Objectives
while complying with all relevant national and
international requirements.

PLEASE NOTE:
Reasonable care has been taken in preparing this catalog. Steel & O’Brien Manufacturing. Inc. reserves the right to make
changes or corrections to any of the product information, including dimensions, listed herein without notice.
Proudly Serving Our Customers For Over 30 Years
CRN Certified

7869 Route 98
Arcade, New York 14009
Tel: (585) 492-5800 © Steel & O’Brien Mfg. Inc.
sales@sob.us Form No.002 09/22