Protect Fuse Switch Disconnector, XLBM 160-630A
Protect Fuse Switch Disconnector, XLBM 160-630A
Protect Fuse Switch Disconnector, XLBM 160-630A
Contents
Fuse protection General
1 2
Technical data
4
Ordering tables
5
Dimensional drawings
InLine
1. Fuse protection
Fuse protection Easy and reliable
The fuse is a superior short circuit protection element regarding the maximum allowed cut-off current (peak let through current) and energy value. This is more important the higher the voltage and prospective fault levels are. The SlimLine switch fuses fulfil the highest requirements for modern switch fuses with a total safety concept. The switch fuses are tested according to the EN 60947-3 standard with more stringent requirements for isolation, making, performance and safety. The melting curves and current limiting diagrams for NH fuse links are given in the IEC 269-2 standard. The standardised fuse characteristics and high degree of current limitation ensure that there is a simple and effective coordination with fuse links and other devices. Fuse links provide a simple procedure for selecting the right fuse type for your installation, without complicated calculations or calculation tools. Fuses prevent "blackouts". Only the fuse nearest a fault trips without upstreams fuses (feeders or mins) being affected. Fuses thus provide selective coordination. When more power is needed in an installation, more feeders can be added without changing the present structure or any new selectivity calculations. Fuse links will assure selectivity in the installation by 1,6:1 difference in the rated current.
Economical installation
Lifetime costs of fuse systems are low. Fuse links which can withstand a high fault level and a fault current, are available at economical prices. After fuse operation, only the fuse link has to be changed. Because the fuse links can be rapidly and easily replaced, plant down time and maintenance are substantially reduced with a fuse link system. Because the fusing elements operate in a cylinder, they are not affected by their surroundings. Thus their protecting characteristics remain stable year after year. The dynamic stress on the network and its equipment is dependent of the let through energy (i2t) at a short circuit. The fuse link provides the best protection compared to other solutions, at high short circuit currents. As the fuse link body is filled with quartz sand, there will be no emission of gases or arcs when a short circuit occurs. This again leads to less stress on the network and a higher degree of personal safety.
InLine
2. General
InLine is the new generation of vertical fuse rails and fuse switch disconnectors from ABB. ABB has a long history in producing these types of devices, and the first generation was introduced already in 1967. The InLine family consists of fuse rails, single-, and triple pole operated fuse switch disconnectors and incoming/outgoing units.
Areas of applications
Cable distribution cabinets (CDC) Low voltage distribution in secondary transformer substations Distribution boards for industry, housing and office buildings
Inplan
InPlan is a software tool for planning and designing InLine applications. It may be used to have: - Front view diagram - Single line diagram - Material list These can all be printed and used for documentation and offers where InLine is used.
Applications
Cable distribution cabinets Low voltage distribution in transformer secondary substations Switchboards for industries Installations
6
1SEC312022B0201
InLine
2. General
Properties
Fully type tested in accordance with IEC 60947-3 Compact 48 and 98 mm width 185mm busbar distance For flat or IP20 z-profile busbar Wide range of accessories Possibility of top, bottom or side cable connection IP20 from the front Available with Electronic Fuse Monitoring (EFM) Current metering on both the cable and busbar side Safe live installation with IP20 system V0 flame retardant materials
Advantages
Complete range for all applications Modern and sturdy design Flexibility snap on solutions
Industrial IT describes the ABB group commitment to bridging the gap between industrial and business assets and the information technology (IT) required to integrate these components in real time. The commitment encompasses a portfolio of compatible technologies for power, automation, and information; a robust, open architecture for integrated solutions; plus the domain expertise acquired through more than 100 years of meeting customer needs. This product has been certified by ABB Group as Industrial IT nabled - Information Level. All product information is supplied in interactive electronic format, based on ABB Aspect Object technology. The Industrial IT commitment from ABB ensures that every enterprise building block is equipped with the integral tools necessary to install, operate, and maintain it efficiently throughout the product lifecycle.
7
1SEC312022B0201
InLine
3. Apparatus and accessories
3.1 Standard apparatus XUBM fuse rail
XUBM1/2/3 NH1/2/3 250 A 400 A 630 A 100 mm 95 - 240 3 x M12 XUBM1 1SEP102111R0101 XUBM2 1SEP102112R0101 XUBM3 1SEP102113R0101
50 mm ) ) 1,5 - 95 3 x M8 1SEP101836R0001
50 mm 1,5 - 95 3 x M8 1SEP10211R0101
1. Cable lugs in accordance with DIN 46235 and DIN 46239. 2. Cable clamps are available as accessories.
8
1SEC312022B0201
InLine
3. Apparatus and accessories
3.1 Standard apparatus XLBM fuse switch disconnector
50 mm ) 1,5 - 95 3 x M8
1SEP101818R0001
50 mm 1,5 - 95 3 x M8 1SEP102140R0101
50 mm 1,5 - 95 3 x M8
1SEP102140R0101
1. Cable lugs in accordance with DIN 46235 and DIN 46239. 2. Cable clamps are available as accessories.
9
1SEC312022B0201
InLine
3. Apparatus and accessories
3.1 Standard apparatus Guide marks
In the back of the fuse rail it is printed guide marks. This makes it easier to mark drilling holes in the busbars.
Hooked clamp
It is possible to install the fuse rail with hooked clamp on live busbar. This feature is further described in the IP20 Z-busbar system chapter. The hooked clamp do not require bolts in the busbars. This enables an easy and quick installation. The hooked clamp covers all busbar widths up to 10 mm.
2
90
1
M12
25Nm
1SEB000107
10
1SEC312022B0201
InLine
3. Apparatus and accessories
3.1 Standard apparatus
Sealing
Voltage measurement
InLine
3. Apparatus and accessories
3.2 IP20 Z-busbar system and apparatus
Type BZ 400 A
BZ 400A/284 BZ 400A/536 BZ 400A/851 BZ 400A/1201
Rated current
Width
Order code
BZ 630 A
BZ 630A/284 BZ 630A/536 BZ 630A/851 BZ 630A/1201 630 A 630 A 630 A 630 A 284 mm 536 mm 851 mm 1201 mm 1SEP824067R0001 1SEP824068R0001 1SEP824069R0001 1SEP824070R0001
XUBM-Z and XLBM-Z may be hooked on: Z busbars type BZ Standard flat Cu-bars
12
1SEC312022B0201
InLine
3. Apparatus and accessories
3.2 IP20 Z-busbar system and apparatus
XUBM1/2/3-Z NH1/2/3 250 A 400 A 630 A 100 mm 95 - 240 3 x M12 1SEP102111R0201 1SEP102111R0121 1SEP102112R0121
XUBM1/2/3-ZS NH1/2/3 250 A 400 A 630 A 150 mm 50 - 300 Clamps 1SEP102111R0405 1SEP102112R0405 1SEP102111R0405
50 mm 1,5 - 95 3 x M8 1SEP102110R0201
13
1SEC312022B0201
InLine
3. Apparatus and accessories
3.2 IP20 Z-busbar system and apparatus XLBM 1 pole-Z fuse switch disconnector
XLBM1/2/31PZ NH1/2/3 250 A 400 A 630 A 100 mm 95 - 240 3 x M12 1SEP102141R0201 1SEP102141R0201 1SEP102142R0201
XLBM1/2/3-1P-ZS NH1/2/3 250 A 400 A 630 A 150 mm 50 - 300 Clamps 1SEP102141R0401 1SEP102142R0401 1SEP102143R0401
XLBM1/2/3-1P-Z2S NH1/2/3 250 A 400 A 630 A 208 2 x 50 - 300 Clamps 1SEP102141R0501 1SEP102142R0501 1SEP102143R0501
50 mm 1,5 - 95 3 x M8 1SEP102140R0201
14
1SEC312022B0201
InLine
3. Apparatus and accessories
3.2 IP20 Z-busbar system and apparatus XLBM 3 pole-Z fuse switch disconnector
XLBM1/2/3-3P-Z NH1/2/3 250 A 400 A 630 A 100 mm 95 - 240 3 x M12 1SEP102141R0221 1SEP102142R0221 1SEP102142R0221
XLBM1/2/3-3P-ZS NH1/2/3 250 A 400 A 630 A 150 mm 50 - 300 Clamps 1SEP102141R0421 1SEP102142R0421 1SEP102143R0421
XLBM1/2/3-3P-Z2S NH1/2/3 250 A 400 A 630 A 208 mm 2 x 50 - 300 Clamps 1SEP102141R0521 1SEP102142R0521 1SEP102143R0521
50 mm 1,5 - 95 3 x M8 1SEP102140R0221
15
1SEC312022B0201
InLine
3. Apparatus and accessories
3.2 IP20 Z-busbar system and apparatus Modules with hooked clamp (Z)
16
1SEC312022B0201
InLine
3. Apparatus and accessories
3.2 IP20 Z-busbar system and apparatus
Load break switch, switch fuse and sectionalising load break switch
Type
Item description
Rated current A
160 250 400 630 160 250 400 630 160 250 400 630 160 250 400 630
Cu/Al mm2
1,5 - 95 1,5 - 95 50 - 300 50 - 300 1,5 - 95 50 - 300 50 - 300 50 - 300
Module width
168 168 217 245 168 217 245 301 168 168 217 245 168 217 245 301
Order code
LB 160 LB 250 LB 400 LB 630 FLS 160 FLS 250 FLS 400 FLS 630 LS 160 LS 250 LS 400 LS 630 FSS 160 FSS 250 FSS 400 FSS 630
160A load break switch 250A load break switch 400A load break switch 630A load break switch 160A switch fuse 250A switch fuse 400A switch fuse 630A switch fuse 160A load break switch-sectionallizer 250A load break switch-sectionallizer 400A load break switch-sectionallizer 630A load break switch-sectionallizer 160A switch fuse - sectionallizer 250A switch fuse - sectionallizer 400A switch fuse - sectionallizer 630A switch fuse - sectionallizer
1SEP731800R0001 1SEP731802R0001 1SEP731804R0001 1SEP731806R0001 1SEP731808R0001 1SEP731810R0001 1SEP731812R0001 1SEP731814R0001 1SEP731816R0001 1SEP731818R0001 1SEP731820R0001 1SEP731822R0001 1SEP731824R0001 1SEP731826R0001 1SEP731828R0001 1SEP731830R0001
17
1SEC312022B0201
InLine
3. Apparatus and accessories
3.2 IP20 Z-busbar system and apparatus
Fuse Monitoring
Electronic Fuse Monitoring (EFM)
The fuse monitor is a fuse blown monitoring and indication device. The voltage supply to the internal electronic device is supported directly by connection to the internal fuse holders. In case of a blown fuse, the internal relay will trip for giving possible remote alarm. Aditionally the green LED lamp in the front will change to red. After replacement to a new fuse link, the relay will automatically be reset. NOTE: The fuse monitor requires supply from the busbar side.
3
Technical data : Minimum operation voltage: Maximum operation voltage: Uimp over a blown fuse : Uimp between phases : Uimp between main circuit/ relay contacts. : Dielectric test voltage input / output : Electrostatic Discharge : Electrical Fast Transient: Conducted Fast transient: Wire size : EMC tested: Relay: Nominal current: Nominal switching capacity: Maximum switching voltage: 380 690V 12,3 kV 9.8 kV 9.8 kV 3.5 kV / 50 Hz / 1 minute EN61000-4-2 +/- 4 kV. EN61000-4-4 +/- 2 kV EN61000-4-6 10Vrms / 150kHz 80 MHz 15 mm2 Yes
1SEB000110
18
1SEC312022B0201
InLine
3. Apparatus and accessories
3.3 Accessories
Accessories XUBM
Cable shroud
19
1SEC312022B0201
InLine
3. Apparatus and accessories
3.3 Accessories
Selector switch
Ammeter house
Front installation
compact fuse for CT and plug-in ammeter available for size 1/2
Terminal installation
kit including extension bar and CT for 1 phase available for size 1/2/3
20
1SEC312022B0201
InLine
3. Apparatus and accessories
3.3 Accessories
Accessories XLBM
Lable holder
Huckepack
for temporary additional output
Micro switch
one or two per phase
Auxiliary switch
Cable shroud
21
1SEC312022B0201
InLine
3. Apparatus and accessories
3.3 Accessories
Cable termination
Conductor cross section min-max Type of clamp/bolt Conductor flexible mm2 Rm/Sm mm2 Re/Se mm2 Torque (Nm) Order code
XLBM / XUBM00
1,5 50
1,5 50
1,5 50
3,5
1SEP407733R0001
3
Single Prism Clamp (SPC) 1,5 95 1,5 95 1,5 95 3,5 1SEP407732R0005
XLBM / XUBM1/2/3
V-clamp kit
95 240
95 240
95 240
25
1SEP304446R0001
2 x 95 240
2 x 50 185 2 x 95 240
25
1SEP304457R0001
2 x 95 240
2 x 70 240
2 x 70 240
25
1SEP304502R0001
22
1SEC312022B0201
InLine
4. Technical data
XUBM1
XUBM2
XUBM3
(kArms) (Hz)
50 50-60
50 50-60
50 50-60
50 50-60
IP 20
IP 20
IP 20
IP 20
1 690 125
400 500 690 400 500 690 400 500 690 200 250 200 315 400 315 500 630 500 250 1000 8 50 50 400 1000 8 50 50 630 1000 8 50 50
50-60
50-60
50-60
50-60
16,1 IP 20 IP 30
16,9 IP 20 IP 30
36,8 IP 20 IP 30
75,4 IP 20 IP 30
23
1SEC312022B0201
InLine
5. Ordering tables
Order number Type designation Item description Weight
Per unit (kg)
XUBM / XLBM
Fuse rail - XUBM
1SEP102110R0101 1SEP101836R0001 1SEP102100R0101 1SEP102111R0101 1SEP102101R0101 1 1SEP102112R0101 1SEP102102R0101 1SEP102113R0101 1SEP102103R0101 XUBM00 XUBM00-100 XUBM00-R XUBM1 XUBM1-R XUBM2 XUBM2-R XUBM3 XUBM3-R 160A incl. 3M8 160A 100mm busbardist. incl. 3M8 160A wo. contact shrouds, incl. 3M8 250A incl. 3M12 250A wo. contact shrouds, incl. 3M12 400A incl. 3M12 400A wo. contact shrouds, incl. 3M12 630A incl. 3M12 630A wo. contact shrouds, incl. 3M12 1,5 1,0 1,3 2,9 2,5 3,4 3,1 3,9 3,6
2
3
Explanation: XUBM XLBM XLBM-2 XUBM-2-R XLBM-2-1P 3 = Fuse rail = Fuse switch disconnector = Apparatus size = Fuse rail without contact shrouds = Number of operating poles
XLBM-2-1P-EFM = Electronic fuse monitoring XLBM-2-Z XLBM-2-ZS XLBM-2-Z2S = Hooked clamp = Hooked clamp and side connection = Hooked clamp and double side connection
24
1SEC312022B0201
InLine
5. Ordering tables
Order number Type designation Item description Weight
Per unit (kg)
Fuse switch disconnector - XLBM 1pole with hooked clamp (Z) 1SEP102140R0201 XLBM00-1P-Z 160A 1pole, w. hooked clamp, incl. 3M8 1SEP102140R0211 XLBM00-1P-EFM-Z 160A 1 pole, incl. EFM, w. hooked clamp, incl. 3M8 1SEP102141R0201 XLBM1-1P-Z 250A 1pole, w. hooked clamp, incl. 3M12 1SEP102141R0211 XLBM1-1P-EFM-Z 250A 1pole, incl. EFM, w. hooked clamp, incl. 3M12 1SEP102141R0401 XLBM1-1P-ZS 250A 1pole, w. hooked clamp, side connection, incl. 3 clamps 1SEP102141R0501 XLBM1-1P-Z2S 250A 1pole, w. hooked clamp, double side connection, incl. 6 clamps 1SEP102142R0201 XLBM2-1P-Z 400A 1pole, w. hooked clamp, incl. 3M12 1SEP102142R0211 XLBM2-1P-EFM-Z 400A 1pole, incl. EFM, w. hooked clamp, incl. 3M12 1SEP102142R0401 XLBM2-1P-ZS 400A 1pole, w. hooked clamp, side connection, incl. 3 clamps 1SEP102142R0501 XLBM2-1P-Z2S 400A 1pole, w. hooked clamp, double side connection, incl. 6 clamps 1SEP102143R0201 XLBM3-1P-Z 630A 1pole, w. hooked clamp, incl. 3M12 1SEP102143R0211 XLBM3-1P-EFM-Z 630A 1pole, incl. EFM, w. hooked clamp, incl. 3M12 1SEP102143R0401 XLBM3-1P-ZS 630A 1pole, w. hooked clamp, side connection, incl. 3 clamps 1SEP102143R0501 XLBM3-1P-Z2S 630A 1pole, w. hooked clamp, double side connection, incl. 6 clamps Fuse switch disconnector - XLBM 3pole with hooked clamp (Z) 1SEP102140R0221 XLBM00-3P-Z 160A 3pole, w. hooked clamp, incl. 3M8 1SEP102140R0231 XLBM00-3P-EFM-Z 160A 3pole, incl. EFM, w. hooked clamp, incl. 3M8 1SEP102141R0221 XLBM1-3P-Z 250A 3pole, w. hooked clamp, incl. 3M12 1SEP102141R0231 XLBM1-3P-EFM-Z 250A 3pole, incl. EFM, w. hooked clamp, incl. 3M12 1SEP102141R0421 XLBM1-3P-ZS 250A 3pole, w. hooked clamp, side connection, incl. 3 clamps 1SEP102141R0521 XLBM1-3P-Z2S 250A 3pole, w. hooked clamp, double side connection, incl. 6 clamps 1SEP102142R0221 XLBM2-3P-Z 400A 3pole, w. hooked clamp, incl. 3M12 1SEP102142R0231 XLBM2-3P-EFM-Z 400A 3pole, incl. EFM, w. hooked clamp, incl. 3M12 2 1SEP102142R0421 XLBM2-3P-ZS 400A 3pole, w. hooked clamp, side connection, incl. 3 clamps 1SEP102142R0521 XLBM2-3P-Z2S 400A 3pole, w. hooked clamp, double side connection, incl. 6 clamps 1SEP102143R0221 XLBM3-3P-Z 630A 3pole, w. hooked clamp, incl. 3M12 1SEP102143R0231 XLBM3-3P-EFM-Z 630A 3pole, incl. EFM, w. hooked clamp, incl. 3M12 1SEP102143R0421 XLBM3-3P-ZS 630A 3pole, w. hooked clamp, side connection, incl. 3 clamps 1SEP102143R0521 XLBM3-3P-Z2S 630A 3pole, w. hooked clamp, double side connection, incl. 6 clamps Modules with hooked clamp (Z) 1SEP731800R0001 LB 160 1SEP731802R0001 LB250 1SEP731804R0001 LB 400 1SEP731806R0001 LB 630 3 1SEP731808R0001 FLS 160 1SEP731810R0001 FLS 250 1SEP731812R0001 FLS 400 1SEP731814R0001 FLS 630 1SEP731816R0001 LS 160 1SEP731818R0001 LS 250 1SEP731820R0001 LS 400 1SEP731822R0001 LS 630 1SEP731824R0001 FSS 160 1SEP731826R0001 FSS 250 1SEP731828R0001 FSS 400 1SEP731830R0001 FSS 630 1SEP731530R0001 LDL 63/3 1SEP731594R0001 AKZD 95 1SEP731521R0001 AKKZ 300 Kit of IP20 Z-busbars 1SEP824063R0001 1SEP824064R0001 1SEP824065R0001 4 1SEP824066R0001 1SEP824067R0001 1SEP824068R0001 1SEP824069R0001 1SEP824070R0001
2,4 2,5 4,5 4,7 4,5 5,8 5,1 4,9 5,0 6,3 5,5 5,7 5,4 6,7
2,5 2,6 4,6 4,8 4,6 5,8 5,2 5,4 5,1 6,3 5,6 5,8 5,5 6,7
160A load break switch 250A load break switch 400A load break switch 630A load break switch 160A switch fuse 250A switch fuse 400A switch fuse 630A switch fuse 160A load break switch-sectionallizer 250A load break switch-sectionallizer 400A load break switch-sectionallizer 630A load break switch-sectionallizer 160A switch fuse -sectionallizer 250A switch fuse -sectionallizer 400A switch fuse -sectionallizer 630A switch fuse -sectionallizer 63A diazed unit w. 3 groups Direct incomer Direct incomer
0,1 0,4
400A/284mm, incl. IP20 busbars&holders 400A/536mm, incl. IP20 busbars&holders 400A/851mm, incl. IP20 busbars&holders 400A/1201mm, incl. IP20 busbars&holders 630A/284mm, incl. IP20 busbars&holders 630A/536mm, incl. IP20 busbars&holders 630A/851mm, incl. IP20 busbars&holders 630A/1201mm, incl. IP20 busbars&holders
25
1SEC312022B0201
InLine
5. Ordering tables
Order number Type designation Item description Weight
Per unit (kg)
Lenght 185mm Lenght 64mm Kit incl. 2 pcs. Kit incl. 3 pcs. 1,5-50 mm2 Kit incl. 3 pcs. 1,5-95 mm2 Single Double For A-meter 48x48mm Kit incl. 3 pcs. 2,5VA cl.1
Kit incl. 2 pcs. Kit incl. 3 pcs. Temporary supply outlet Kit incl. 3 pcs. Kit incl. 3 pcs. For A-meter 72x72mm
5
6
Kit incl. 3 pcs. 3,75VA cl.1 Kit incl. 3 pcs. 5VA cl.1 Kit incl. 3 pcs. 5VA cl.1 Kit incl. 3 pcs. 5VA cl.0,5 Kit incl. 1 pc. 2,5VA cl.1 Kit incl. 1 pc. 3,75VA cl.1 Kit incl. 1 pc. 5VA cl.1 Kit incl. 1 pc. 5VA cl.1 Kit incl. 1 pc. 5VA cl.0,5
0,3 0,4 0,3 0,2 0,2 0,1 0,1 0,3 0,5 0,5 0,5 0,1 0,2 0,2 0,2 1,3 1,3 1,3 1,3 0,6 0,6 0,6 0,6 0,6 0,2 0,2 0,5 0,5 0,5 0,5 0,5 0,5 0,5 0,5 0,5 0,1 0,1
0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,3 0,4 0,7 0,1
Insulated hexagon key NV6 Micro switch Auxiliary switch NC Auxiliary switch NO
26
1SEC312022B0201
InLine
6. Dimensional drawings
XUBM00-100
XLBM00-3P-100
XUBM00
XUBM1/2/3
27
1SEC312022B0201
InLine
6. Dimensional drawings
XLBM00-1P
XLBM00-3P
XLBM1/2/3-1P
XLBM1/2/3-3P
28
1SEC312022B0201
InLine
6. Dimensional drawings
XUBM00-Z
XLBM00-3P-Z
XLBM1/2/3-3P-Z
29
1SEC312022B0201
InLine
6. Dimensional drawings
XLBM1/2/3-3P-ZS
XLBM1/2/3-3P-Z2S
30
1SEC312022B0201
InLine
6. Dimensional drawings
Accessories Size 00
EFM
Label holder
31
1SEC312022B0201
InLine
6. Dimensional drawings
Label holder
6
EFM housing Ammeter house
A part of its on-going product improvement, ABB reserves the right to modify the characteristics or the products described in this brochure. The information given is notcontractual. For further details please contact the ABB company marketing theese products in your country.
P.O. Box 100, Sentrum, N-3701 Skien, Norway Tel. +47 35 58 25 00 Fax +47 35 58 28 00 e-mail: abb.control@no.abb.com www.abb.com
1SEC312022B0201