HXRF-140JP Manual
HXRF-140JP Manual
HXRF-140JP Manual
www.huatecgroup.com
Operating Instruction
China
Dear users,
Hello!
Thank you very much for choosing to buy and use our products. Our products are of
reliable quality and superior performance. For your convenience, please read the
instructions carefully and standardize the operation.
1 Instrument packaging and component composition
The instrument and accessories are packed in a special suitcase, which can be
shockproof, waterproof and dustproof. The instrument should be put back into the
suitcase after use.
To open the suitcase: push down the red buttons on both sides of the suitcase, and
then pull up the buckles on both sides to open the top cover of the suitcase.
Packing List
NAME Instrument charging unit battery operation instruction
host
quantity 1 1 2 1
11
In the picture: 1 -- display screen 2 -- warning light bar 3 -- protection cover 4 -- probe
protection cover against rope loss 5 --
Trigger 6 -- Handle 7 -- Battery cover 8 -- anti-fall lanyard 9 -- main switch 10 --
Material sensing 11 -- Camera 12 -- Auxiliary line of sight 13 -- Detection window
17
18
14 15
16
20 Charging device
In the picture: 14 -- battery front 15 -- battery back 16 -- battery pull cord 17 --
ADD.: B-730 CHENGYUAN BUILDING,MID. OF JIANCAICHENG ROAD,HAIDIAN,BEIJING,CHINA
E-mail:export@huatecgroup.com TEL.:+86 10 82921131 FAX:+86 10 82916893
HUATEC Group Corporation
www.huatecgroup.com
battery quantity display button 18 -- battery quantity indicator 19 -- wiring port 20 --
charging device
2 Usage
2.1 Battery Installation
Before installing the battery, check the battery level. Press the battery level display
button and observe the battery level indicator. If the battery level is less than 25%,
charge the battery or replace the battery.
Pinch the protrusion on both sides of the battery bin cover to separate the card slot
on the battery bin cover from the card buckle on the battery bin, rotate the battery
bin cover, open it;When installing the battery, hold the instrument handle with your
right hand and keep the display screen facing your side. Insert the battery wiring port
vertically into the battery compartment with the battery wiring port facing the upper
left. After the battery is firmly inserted, rotate the battery compartment cover in the
opposite direction and fasten it tightly.
2.2 boot
Keep the probe protection cover in the installation state, press the power switch, the
power indicator lights up, and then the screen enters the boot interface. After a
moment, enter the user login interface, input the account and password, click [Login],
and then < Login succeeded > appears, and the boot is complete.
After startup, first enter the [Measurement] interface, wait until the screen appears
"Ready", then pull the trigger or click the green circular [Start] button at the top of
the screen to start the test.Top elements can be selected by element option (one or
more top focus elements can be selected), and unit of measurement can be selected
by PPM option (optional PPM or % option)
During the test (the left and right sides and above the screen light flashing, the red
light of the start button flashing, the interface "Do not pull the trigger during sample
test"), be sure to keep the relative position of the tested sample and the test window
unchanged.When the interface appears "test completed, you can pull the trigger", it
indicates that the test is completed, and the next sample can be tested according to
the above method, or other operations.
Attention should be paid to:
1) During the test, if the test needs to be stopped immediately, press the trigger to
stop the test.
2) To prevent irregular objects from piercing the protective film of the detection
window and damaging the probe beryllium window, and the instrument should be
avoided from shaking during the detection process.
3) It is impossible to detect without objects in front.
2.4 Data Viewing
Data can be viewed in the Measurement or Results interface.
[Measurement] View data on the interface
From the end of each measurement to the beginning of the next measurement, the
[Measurement] interface will display the latest measurement data, including the
elements and content of the sample, plus or minus statistical error value and other
information.
(1) Sample label: Set the name of the sample to facilitate subsequent inspection of
test data
(2) Intelligent fine-tuning: used to manually fine-tune the test results to make the
results more accurate.
(3) Data export: data can be output through mailbox and Bluetooth
(4) Data export Settings: mailbox can be added
(5) Variance threshold: used for intelligent switching between different test
algorithms.(Factory default values are recommended)
The above options are shortcuts in the "Settings" menu.
Click "Settings" to enter the tool menu interface, which consists of 6 menus including
"Interface Settings", "Collection Settings", "Analysis Settings", "Brand Settings",
"System Settings" and "Shutdown lock screen".
(2) "Material sensing Setting" is used to see if there is an object in front of the
sensing test window
(2)"Intelligent Fine-tuning" is used to manually fine-tune the test results to make the
results more accurate.
(3) "Result Display Setting" is used to set the lower limit of element content that can
be displayed in the interface. Elements whose content is less than this value will not
be displayed in the result interface.
(1) "number of brands displayed" refers to the number of brands displayed on the
[measurement] interface. For example, if the value is set to 3, the 3 brands displayed
on the [measurement] interface are closest to the test results.
(3) "standard display setting of brand number" includes 8 kinds, respectively: only
display brand name, display GB, display American standard and other existing brand
number library element content information.
(4) "Brand standard display Settings" can be added according to customer needs
brand library.
(5) "brand number display mode" has two kinds, respectively: display multiple at the
same time, display one at a time.
(2) "Data export" includes two output modes of "Bluetooth" and "mailbox"
Bluetooth transfer procedure - Select the file to be transferred - Confirm - Generate
PDF file - Select bluetooth device - Confirm to send.As is shown in
(3) "Mailbox" transfer step, first in [measurement] - soil - Data export setting - add
mailboxaddress, and then click confirm as prompted.As is shown in
(4) In "History", users can send and delete data statistical details atlas.As is shown in
The procedure for deleting data is as follows:
(5) Click the "User Management" menu to create new users. New users can be
divided into advanced users and ordinary users according to different levels.The two
types of new users are created in the same way but with different permissions, as
shown in Table 1.
In the Level column, select Advanced User or Common User, enter the user name and
password, and click Add to create a user.
(9) "Remote assistance" when customers encounter problems that cannot be solved,
they can first contact after-sale technical personnel of the company, and send
one-click diagnosis according to the guidance of after-sale technical personnel to
solve the problem.