9651 Engineer
9651 Engineer
9651 Engineer
PROGRAMMING GUIDE
9651
HARDWIRED CONTROL
PANEL
9651 Hardwired Control Panel Installation and Programming Guide
Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security
Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book
are subject to change without notice.
Printed and published in the U.K.
Part number 496929 Issue 2
Contents
1. INTRODUCTION.......................................................................................... 3
Operator Controls and Displays - 9930 ..........................................................................................................4
System Features.............................................................................................................................................5
Detectors ......................................................................................................................................................5
User Control .................................................................................................................................................5
2. Technical Description ................................................................................ 6
Specification ...................................................................................................................................................6
Power Supply ...............................................................................................................................................6
Outputs .........................................................................................................................................................6
Inputs............................................................................................................................................................6
Fuses............................................................................................................................................................6
Control Unit PCB ............................................................................................................................................7
3. INSTALLATION ........................................................................................... 8
Overview.........................................................................................................................................................8
Cabling Keypads ............................................................................................................................................8
Fitting the System...........................................................................................................................................9
Fitting the Control unit Case.........................................................................................................................9
Fitting a 9930 Keypad ..................................................................................................................................9
Wiring the Control Unit .................................................................................................................................11
Cable Entries ..............................................................................................................................................11
Mains Connection.......................................................................................................................................11
Remote Keypads ........................................................................................................................................12
Connecting Keypads, Exit Terminate Buttons, Lock Switches and Sounders..............................................................12
Detector Circuit Connections......................................................................................................................13
Using Programmable Outputs ....................................................................................................................14
Wiring Keyswitches ....................................................................................................................................15
Fitting a Plug-by Communicator .................................................................................................................16
Fitting a Battery ............................................................................................................................................18
Initial Start Up ...............................................................................................................................................18
4. Programming ............................................................................................ 20
Entering Programming Mode........................................................................................................................20
Programming Commands.............................................................................................................................20
Leaving Programming Mode ......................................................................................................................24
Engineer Reset...........................................................................................................................................24
Re-entering Programming Mode ................................................................................................................25
Restoring the Access Codes (1st stage reset)...........................................................................................25
Restoring All Factory Default Programming...............................................................................................25
Programming Command Reference.............................................................................................................26
0: Country Defaults.....................................................................................................................................26
01 - 08 : Zone Programming ......................................................................................................................26
20: Change Engineer Code........................................................................................................................30
21: Zone Configuration...............................................................................................................................31
22: Loudspeaker Chime .............................................................................................................................31
23: RedCare Reset.....................................................................................................................................31
25: Continuous Sounder.............................................................................................................................31
27: Exit Fault External Sounders................................................................................................................31
28: Status Display.......................................................................................................................................32
29: Entry Alarm Delay Time .......................................................................................................................32
30: Silent or Audible PA .............................................................................................................................32
31: Zone Tamper Reset .............................................................................................................................32
33: System Reset .......................................................................................................................................33
34: PA Reset ..............................................................................................................................................33
35: First Circuit Response ..........................................................................................................................33
36: Alarm Abort...........................................................................................................................................33
37: Daytime Tamper Communication.........................................................................................................33
38: System Tamper Reset..........................................................................................................................34
496929 Page 1
Contents
Page 2 496929
1. INTRODUCTION
The 9651 control unit is designed to be fully programmable to suit individual
site requirements and user needs. Note that in the UK the product does not
comply with the ACPO 2000 alarm policy and DD243: 2002.
The system comprises a control unit in a metal shielded case and up to four
separate keypads (see Figure 1 on the next page). You should always fit at
least one keypad.
The control unit provides:
° A four-wire bus connection for keypads.
° Connections for eight Fully Supervised Loop (FSL) zones or eight Closed
Circuit Loop (CCL) with a common tamper.
° Connections for three fully programmable outputs.
° Internal sounder loudspeaker output with electronically generated Chime,
Alarm, Fire and Entry/Exit tones. (The volume of the Entry/Exit and Chime
tones can be adjusted).
° Pins and wired harness for a plug-by communication device.
The control unit provides connectors for eight Closed Circuit (CC) zones or
eight Fully Supervised Loop (FSL) zones on its own printed circuit board.
The control unit supports the 9930 sixteen character Liquid Crystal Display
(LCD) keypad. The keypad(s) can accommodate the 934EUR-00 “Prox”
reader module to allow the end users to set and unset the system using a
“Prox” token in place of a four digit access code.
As an Installer you can program the system from the keypads. When
programming from the keypads the programming interface is arranged as a
set of three-digit numbered commands similar to those used by the 9800
family of products.
The system can provide for up to 16 separate users. User facilities include:
° Four different security levels (full and three part sets) on the 9651. The
levels can be programmed by the Installer.
° User programmable Duress code.
° Keyswitch setting/unsetting.
° Dual key PA alarm from the keypads.
Setting, unsetting & resetting using a “Prox” token
Before attempting to program the system, make sure you are completely
familiar with the functions of the system and its programmable options.
496929 Page 3
3. Introduction
The 9930 keypad has a 32 character LCD display that shows "first to alarm"
information, level status, and programming commands. In addition there are
three LEDs with the following functions:
Page 4 496929
3. Introduction
496929 Page 5
2. Technical Description
Specification
Environmental -10° to +40 °C.
EN50131 “Class II” 75 % RH.
Dimensions Junior combi box: 243mm W, 234mm H,
87mm D
Weight Junior combi box: 2.45 kg (without standby
battery)
Internal Clock ±10 minutes over one year (depending on the
accuracy of the mains supply frequency).
Conforms to BS4737 1986 Part 1. for Audible or Remote signalled systems.
Designed to fulfil the requirements of a EN 50131-1 Grade 2 Intruder Alarm
System.
Power Supply
All currents accurate to ±5%.
System power supply 230VAC +/- 10% (ambient Temp. 20°. C)
1.0A total.
Control unit power 115mA nominal quiescent, 150mA active.
9930 Remote Keypad 20mA quiescent, 35mA with keypad backlight
on.
Standby Battery 12 Volt, 7.0AH rechargeable lead-acid, Gel
Type battery (not supplied).
Power Supply Type A power supply designed to fulfil the
requirements of EN 50131-1 Grade 2.
Outputs
O/P 1, 2, 3 3 open collector transistor outputs, 500mA,
12VDC, negative applied.
LS Can support two parallel connected externally
mounted 16 Ohm loudspeakers for internal
sounder or EE tones.
AUX 500mA maximum, 12VDC.
Coms OP1-8 12V logic outputs, -ve applied in alarm (+ve
removed).
Inputs
TR = Tamper return for bell.
Tellback/RedCare reset* = +12V applied to operate reset.
Line Fault input = +12V applied to indicate line failure.
Fuses
F1 - 12V AUX 1A Fast.
F2 - Battery 2A Fast.
Caution: When replacing fuses use the ratings quoted above.
Page 6 496929
2. Technical Description
12V AUX
F-1A
12
11
10
1
BATT F-2A
9
8
3 6
5
1. Outputs. 7. NVM Reset pins.
2. Aux power. 8. Battery connector.
3. Tamper switch. 9. Battery fuse.
4. Zone connectors. 10. Kick start pins.
5. Keypad bus. 11. 21VAC from transformer.
6. Communications Outputs. 12. 12V AUX fuse.
496929 Page 7
3. INSTALLATION
Overview
A typical installation comprises the following main steps:
1. Carry out a Risk Assessment of the premises and agree a security grade
for the proposed alarm installation. Decide on positions for wired
detectors, control unit, keypads, external and internal sounders. As part
of the site survey ask the user what facilities they require .
3. Ensure that there is a suitable mains supply present at the site of the
control unit.
4. If you are going to use a communication device (for example a Speech
Dialler) arrange for a PTT (Public Telephone and Telegraph) connection
point near to the control unit.
5. Install the wired detectors and run cables to the control unit. Connect
each detector to its cable.
7. Run cables from the keypads, external and internal sounders to the
control unit.
8. Install keypads and connect them to their cabling. Ensure that each one
has the correct address setting.
9. Install internal and external sounders and connect them to their cabling.
10. Install the control unit and connect it to the mains supply cabling. Do not
apply power at this point.
11. At the control unit, complete all connections to keypads, and sounders.
12. Apply power and program the control unit.
13. Test that the alarm system functions as required.
14. If required, install a communication device (for example a Speech
Dialler), connect it to the PTT network, and check that it functions
correctly.
15. Hand the system over to the user and instruct them in its use.
Cabling Keypads
Cooper Security recommend that you use a minimum 4-core 7/0.2 alarm
cable for wiring keypads.
You can connect the keypads in either a star or bus configuration. If you are
intending to use long cable runs then Cooper Security recommend that you
use star wiring with no more than 300m of cable total for the keypad wiring.
The maximum length of any one run from control unit to the most remote
keypad depends on the number of items connected to the cable. You can
double the maximum length by using two cores each for the 0V and 12V
terminals or by using 16/0.2 cable. The table below shows the maximum
Page 8 496929
3. Installation
recommended cable lengths in metres for 7/0.2 cable, assuming that you
connect all items at the end of a single cable run. In real life you may be able
to improve on these figures by spreading items along the cable length.
7/0.2 8-core cable Length (m)
No items 1 core 2 cores on 0V
and 12V.
One 200 —
Two 100 200
Three 65 130
Four 50 100
It is possible to extend the keypad cable run by using additional power
supplies, but only up to a recommended maximum of 300m
When carrying out the cabling there are two important points to remember:
1. Do not connect anything other than keypads to the keypad bus. The
keypad bus power supply is limited to a maximum of 400mA and can supply
no more than a maximum of four keypads.
2. Make sure that the voltage between 0V and 12V of the keypad bus at the
furthest point from the control unit is at least 12.0VDC when all the keypad
backlights are on.
Note: The following instructions assume that you have already run all the
necessary cabling.
496929 Page 9
3. Installation
1 1
1 1
1. Fixing hole.
2. Adjustable cam.
6. Mount the front of the keypad (containing the keypad pcb) onto the
backplate and make sure that the tamper switch operates.
8. If the tamper switch does not operate then rotate the cam until the
tamper switch operates correctly when the front of the keypad is
mounted on the backplate.
9. If the “Prox” reader and tags are required, follow the installation
instructions in the separate guide supplied with the 934EUR-00 Prox
reader.
Page 10 496929
3. Installation
To Control Panel
Transformer
L N
230V ~50Hz 200mA
T 250mA 250V
Connect the 21VAC lead from the mains transformer to the main pcb. See
Figures 3 for the location of the 21VAC connector.
Caution: Do not apply mains power at this point. Do not work inside the
control unit case when mains power is present.
496929 Page 11
3. Installation
Remote Keypads
Keypad Addressing
The control unit is supplied with one remote keypad. If you have fitted more
keypads then each one must be given a separate "address". Links LK2 to LK4
set the keypad address, as shown in Figure 6.
Address Keypad 1 Keypad 2
2 2 2
3 3 3
4 4
4
Keypad 3 Keypad 4
2 2
3 3
4 4
ON
BACKLIGHT
ON ON
BACKLIGHT BACKLIGHT
Backlight ON Backlight OFF
Keypad Backlight
When supplied from the factory the control unit is configured with the keypad
backlight ON. To turn the keypad backlight OFF remove the jumper from the
"ON BACKLIGHT" link, shown in Figure 6.
Connecting Keypads, Exit Terminate Buttons, Lock Switches
and Sounders
Figure 7 shows the connections for any of the remote keypads.
To connect an exit terminate button use the "ET" connector terminals on the
keypad PCB.
Use the "ET" connector terminals to connect a Lock Switch. If using a lock
switch do not connect any other device to the "ET" terminals.
Note The lock switch must be closed circuit when the lock is unlocked.
Figure 7 shows the connections for the internal and external sounders.
Page 12 496929
3. Installation
9930 Keypad
Lock Switch
OR
Exit terminate button
(NO, push to make)
9651 Control
0V 12V CLK DATA ET
Unit
0V 12V CLK DATA
To other
keypads 4-core
496929 Page 13
3. Installation
FSL Connections
The control unit zone connectors provide space for up to eight FSL zones.
Each FSL zone is a ‘Fully Supervised Loop’ using a two wire closed loop. The
loop uses two resistors of different values to differentiate between ‘Circuit’ and
‘Tamper’ signals: a 2K2 resistor fitted in series at the end of the wired loop,
and a 4K7 resistor fitted across the alarm contact, see Figure 9.
With the loop in a normal state and the alarm contacts closed (shorting out the
4K7 resistor), the total resistance of the loop is 2K2. When the alarm contacts
open (removing the short from the 4K7 resistor) the resistance of the loop
increases to 6K9 and the control unit detects an alarm condition. If a tamper
device opens then the loop resistance will be open circuit and the control unit
detects a tamper signal.
To connect a detector to an FSL loop you must wire suitable resistors to the
detector. Always check resistor colour coding before wiring resistors into
circuit, see Figure 10.
The wiring resistance of the cable to the detector (including joints) should be
restricted to a maximum of 100 ohms. The recommended maximum cable
distance per zone is 200 - 300 metres.
4K7
Alarm contacts
2K2 EOL Zone 1
Tamper contacts 1
2
4K7
Zone 2
Alarm contacts
2K2 EOL
Tamper contacts
Yellow Red
Violet Red
4k7 Red 2k2 Red
Gold Gold
Note: You can leave the global anti-tamper connectors unlinked if you are
using FSL wiring.
Page 14 496929
3. Installation
Wiring Keyswitches
To allow a user to set and unset the system using a keyswitch, connect a
fixed position or spring loaded (momentary) key switch to a zone input. Note
that a key switch cannot reset the system. When programming the control unit
select zone type (KM) for momentary or (KF) for fixed position keyswitches.
Figure 12 shows the connections for a keyswitch.
Fixed Keyswitch (KF)
Keyswitch CC FSL System
CC Wiring CCT(n)
OFF Closed 2k2 Unset
ON Open 6k9 Set
4k7
Momentary Keyswitch (KM)
Keyswitch CC FSL System
FSL Wiring 2k2 CCT(n) Operate Close-Open- 2k2-6k9-2k2 Unset
Close
Operate Close-Open- 2k2-6k9-2k2 Set
Close
496929 Page 15
3. Installation
Page 16 496929
3. Installation
496929 Page 17
3. Installation
Fitting a Battery
Fit a rechargeable battery into the back of the case. The case provides space
for a 12V 7AH battery. Make sure the battery terminals are oriented in the
position shown in Figure 16.
7AH
Initial Start Up
Before applying power to the control unit, ensure that:
• All remote keypads have been addressed and connected.
• All external and internal sounders are connected.
• All wired zone circuits are connected.
Then:
1. Connect the battery to the control unit PCB.
2. Briefly short the kick start pins together (they are located above battery
connector, see Figure 3).
The green power LED on the keypad flashes and the internal sounder
may sound. Ignore any display at this stage.
3. Key-in the factory default user access code: 1234.
The internal sounder stops. Ignore any display at this stage.
4. Please fit the case lid before applying mains power (this also defeats the
tamper switch).
5. Apply mains power.
Page 18 496929
3. Installation
496929 Page 19
4. Programming
Entering Programming Mode
Installation - Initial Power Up” describes how to enter programming mode for
the first time in a new installation. If you wish to enter programming mode at
any other time:
1. Make sure the system is unset.
2. Press 0, then key in the Engineer’s code (default 7890).
The display shows: Installer Mode
You are now in programming mode.
While the system is in programming mode all keypads except the one you are
using will be locked, displaying “Busy”.
Programming Commands
When delivered from the factory the control unit already has default program
settings. To change the default programming you must be in programming
mode. Then:
1. Key in the appropriate Command number and press Y.
The display shows the current value of the Command.
2. Key in digits to select the value you require.
The display shows the new value.
3. Press Y to store the new value of the Command.
If at any time you change your mind, repeat step 1 to 3. The table on the
following pages shows the Commands and their options. ( A “Y” next to a
Command value shows that it is the factory default.)
The factory default access codes are:
Engineer Code 7890
Access Code User 1 1234
Access Code Users 2 to 16 X 002 .... X 016 (inactive)
Duress Code X017 (inactive)
Note: The factory default Access Codes 02 to 16 and the Duress Code must
be changed by USER 1 to a four digit number to activate them. See
“9651 User Guide” for a more detailed explanation of changing user
access codes.
Page 20 496929
4. Programming
496929 Page 21
4. Programming
Page 22 496929
4. Programming
78 Level D Entry Time 78YnY 92 Test Output 2 See “5. Testing” 92Y
1 10 seconds Output 2 operates, press X or Y to end
2 20 seconds Y test.
3 30 seconds
93 Test Output 3 See “5. Testing” 93Y
4 45 seconds Output 3 operates, press X or Y to end
5 60 seconds test.
6 120 seconds
94 Test Internal Sounder (Single 94Y
79 Level D Exit Time 79YnY System Only) See “5. Testing”
1 10 Seconds Internal sounders operate, press X or
2 20 seconds Y Y to end test.
3 30 seconds
95 Test Kpd Sounder See “5. Testing” 95Y
4 45 seconds
Keypad sounders operate, press X or
5 60 seconds
Y to end test.
6 120 seconds
97 Engineer Walk Test See “5. Testing” 97Y
81 Output 1 Type, one of 81YnY Zn indication and chime operate when
Where n is one of the following: cct open
00 Bell (default full/part set sys.) Y (Clear) End walk test
01 EE follow 98 Load Defaults 98Y1Y
02 Armed lamp
03 Set latch 99 Leave Programming 99YY
04 Shock sensor reset 126 Language 126YnnY
05 Walk test
nn = 0 = English(Y)
06 Ready lamp 1 = Italian
07 24 hour alarm 2 = Espanol
08 Strobe 3 = Portugu
09 Smoke sensor reset 4 = Nederl
10 French Siren Test 5 = Francai
11 Strobe Set 6 = Deutsch
7 = Norsk
12 Pulse Set o/p 1
8 = Svenska
13 Pulse Unset o/p 1 9 = Dansk
26 Pulsed Set o/p 1
27 Pulsed Set o/p 2 151 Plug by Comms Output 1 151YnnY
28 Pulsed Set o/p 3 nn 00 Not Used
01 Fire (default)
29 Pulsed Set o/p 4
02 PA
30 Pulsed Unset o/p 1 03 Burglar
31 Pulsed Unset o/p 2 04 Open/Close
32 Pulsed Unset o/p 3 05 Alarm Abort
33 Pulsed Unset o/p 4 06 Technical Alarm
11 AC Fail
82 Output 2 Type, one of 82YnY
12 Tamper Alarm
See Command 81 for a list of options.
13 Open
Default for Command 82 is 08 Strobe.
14 Close
83 Output 3 Type, one of 83YnY 15 Zone Omitted
See Command 81 for a list of options. 16 Medical
Default for Command 83 is 03 Set 17 Key-Box
latch. 18 Anti-Mask
19 Smoke Detector
85 Burg Comms Rearm 85YnY 30 Set o/p 1
31 Set o/p 2
0 Latch Y 32 Set o/p 3
1 Rearm 33 Set o/p 4
34 Unset o/p 1
86 Dual Ply Entry 86YnY
35 Unset o/p 2
0 Off Y
36 Unset o/p 3
1 On (not recommended in U.K.) 37 Unset o/p 4
87 Dual Key Alarm 87YnY 152 Plug by Comms Output 2 152YnnY
0 Off Y Default 02 PA. See Command 151
1 On
153 Plug by Comms Output 3 153YnnY
90 Event Log* 90YnY Default 03 Burglar. See Command 151
0 Print log
1 View earlier events 154 Plug by Comms Output 4 154YnnY
3 View later events Default 04 Open/Close. See Command 151
X Cancel viewing 155 Plug by Comms Output 5 155YnnY
Y Toggles time/date display Default 15 Zone Omitted. See Command 151
91 Test Output 1 See “5. Testing” 91Y 156 Plug by Comms Output 6 156YnnY
Output 1 operates, press X or Y to end Default 05 Alarm Abort. See Command 151
test.
496929 Page 23
4. Programming
2. Press Y.
The display shows: 99:Checking Sys
followed by the time and date.
The system is now in user mode.
Note: If there is a fault, for example an open tamper circuit, the display shows
this and will not return to Day mode. Press X and rectify the faults.
Engineer Reset
To perform an Engineer Reset:
1. Check that the display is showing the alarm condition.
2. Key in 0 followed by the Engineer’s code (default 7890), followed by 99
YY.
The display shows the time and date.
Page 24 496929
4. Programming
496929 Page 25
4. Programming
01 - 08 : Zone Programming
The zone programming Commands 01 to 08 take three or more digits. The
first two digits describe the zone type, subsequent digits describe the zone
attributes.
When you key in the zone number and press Y the display shows the zone
number and any text caption for the zone. At this point you can edit the zone
text (see next page). Press Y again to start entering the zone types and
attributes. When you have entered the zone type and attributes press Y once
more to store the changes.
Zone Names
When you key in the zone number and press Y the display shows the current
zone name with a flashing cursor under the first letter. Enter letters from the
keypad one at a time by pressing a number key repeatedly until the display
shows the letter you want. You may already be familiar with typing out short
messages on a mobile phone using the same sort of system. Figure 17
shows which letters are assigned to each key. Press C to move the cursor to
the next space for a new letter.
If you make a mistake press C or D to move the cursor over the letter you
want to change, and key in the new letter. If you want to delete a name
completely press D to move the cursor under the extreme left hand character
of the name. Press D again. The display clears the old name.
The system can store a maximum of 12 characters per name, including
spaces and punctuation marks.
When you have finished entering the user name press Y.
Page 26 496929
4. Programming
Zone Types
The following types are available:
00 Not Used (NU) The system ignores Zones with this type. Key in 00 for
a zone that will not be used.
Note: If a zone is programmed as ‘Not Used’, it is not necessary to link the
circuit or anti-tamper connections.
496929 Page 27
4. Programming
06 Entry Route (ER) - Use this zone type for detectors sited between the
Final Exit door/detector and a keypad. If an ‘Entry Route’ zone is
violated when the system is set, an alarm will occur. If the entry/exit
timer is running when an Entry Route zone is violated then no alarm
occurs until the entry/exit timer expires.
07 Shock Analyser (SA) - You can apply this zone type to zones 1 to 4
Only. This zone type can accommodate up to 4 - 5 “Inertia” type
sensors normally fitted on windows or patio doors.
(See also “Zone Attributes - Sensitivity”.)
08 Technical (TC) - Use this zone type when you want to monitor
equipment, for example a freezer, without raising a full alarm. If a
technical alarm zone is activated while the system is set, the system
makes no audible alarm. However, when a user unsets the system the
keypad indicates a fault. If a technical alarm zone is activated while
the system is unset then the system starts a pulsed tone from the
keypad. If programmed, the control unit also starts communication.
When a user enters a valid code the keypad stops the tone and
displays the zone.
09 Key Box (KB) - This zone type is for use in Scandinavia only. When a
zone of this type is required, the Installer connects the alarm wires of
the zone to a special external key box and the tamper wires to the
box enclosure switch. When someone opens the box the control unit
logs the event and communicates it to the ARC. The control unit also
provides a Key Box output type that you can program to trigger one of
the plug by communicator output pins, see Command 151.
10 Smoke Detector (SD) - Use this type for zones connected to 12V
smoke detectors. This type is active whether the system is set or
unset and the control unit will transmit a specific alarm to the ARC if
triggered. The control unit also provides a Smoke Detector output type
that you can program to trigger one of the plug by communicator
output pins, see Command 151.
If a zone of this type causes an alarm then the user will need to enter
an access code to disarm and reset the system.
Key Switch - There are two Key Switch zone types: Momentary and
Fixed. These two zone types are intended for use on zones that
connect to an access control keypad, electronic key or other type of
hardwired device used to set or unset the system.
When the user operates the Keyswitch while the system is unset then
the control unit starts the programmed exit mode.
When the user operates the Keyswitch while the system is set then
the control unit unsets the system immediately.
The user cannot reset the sytem from a Keyswitch zone.
Page 28 496929
4. Programming
X2 Soak Test (S) Use this zone attribute if you want to place under long
term test a detector that you suspect is giving false alarms. Zones with
this attribute are disabled for 14 days after you return the control unit
to user mode. If the zone is opened while the system is set then the
Service LED glows and the control unit logs the event as a “Soak Test
Fail Zn” (n is the zone number) without sounding any bells or starting
signalling. The Service LED stays alight until the Engineer resets the
system. After midnight on the 14th day the control unit returns the
zone to normal use.
Note: Soak test is available only for Normal Alarm, Entry Route, Technical
and Shock Analyser zone types.
496929 Page 29
4. Programming
X3 Double Knock (2) Zones with this attribute will cause an alarm
condition only if one or more sensors generate two alarms events
within a five minute time window, or if one zone remains open for
more than 10 seconds. Programming a zone as ‘Double Knock’ is a
way of reducing false alarms caused by environmental changes, but is
not normally recommended.
Note: ‘Double Knock’ is available only for Normal Alarm and Entry Route
zone types.
X4 Omit Allow (O) When applied to a zone, this attribute allows the user
to omit the zone.
B Level B When applied, the zone will be armed when the user selects
Level B.
C Level C When applied, the zone will be armed when the user selects
Level C.
D Level D When applied, the zone will be armed when the user selects
Level D.
X7 Sensitivity When you use this Command you must also enter an extra
digit in the range 1 to 6 in order to set the sensitivity of the shock
sensor. 1 is least sensitive, 6 is most sensitive. Note that to use this
attribute you must make one of zones 1 to 4 a shock analyser type.
To adjust the sensitivity you must enter the complete Command, for
example to change the sensitivity to 3 you must key in: X7 + 3.
20: Change Engineer Code
To change the Engineer access code:
1. Make sure you are in programming mode.
2. Key in 20 and press Y.
The display shows: 20:Code
4. Press Y.
Page 30 496929
4. Programming
After an alarm the user keys in their access code to silence the alarm, but
cannot reset the system. The first to alarm display and Service LEDs remain
visible. The user contacts the ARC, who verifies the user's identity. The ARC
sends a signal back to the control unit. The Service LED goes dark and the
end user can now reset the system with any valid access code, providing that
there are no faults.
Use option 0 (the default) to disable the function.
25: Continuous Sounder
Option 0 of this Command makes the internal sounder follow the external bell
delay and duration times. Option 1 makes the internal sounder continue after
the external bell times out.
27: Exit Fault External Sounders
When programmed with option 0 the system operates the internal sounders if
the user tries to exit while a zone is still violated (for example a door is not
shut). When programmed with option 1 the system operates the external
sounders as well as the internal sounders.
496929 Page 31
4. Programming
Page 32 496929
4. Programming
496929 Page 33
4. Programming
To set the system the user first enters their access code at a keypad.
The control unit starts the exit tone. Note that the exit time is infinite in
this option. The user then closes the final exit zone and turns the key
in the lock switch to “locked”. The system sets seven seconds after
the lock switch contacts open (detector settling time), and changes the
final exit zone to a Normal Alarm zone.
To unset the system the user turns the lock switch to “unlocked”
(closing the lock switch contacts). The keypads start a continuous
tone. When the user opens the final exit zone the control unit starts
Page 34 496929
4. Programming
the entry timer. The user completes entry by unsetting the system in
the normal way.
Note: If an intruder opens the final exit door without first unlocking the
lockswitch then the control unit immediately starts an alarm.
If you select Timed (options 0), Terminate (option 1), or Final Door (option 2)
exit modes the system allows a seven second settling time after pressing an
exit terminate button or closing a final door.
40: System Auto Re-Arm
This Command lets you program the number of times that the system will re-
arm when the bell delay expires. The system re-arms all closed zones. Select
option 0 to make the system never re-arm (the system will go into alarm once
only). Select options 1 to 4 to make the system re-arm once, twice, three
times or always.
Use this Command in conjunction with Command 35 - First Circuit Response.
If the system has rearmed, then when a user enters the system through the
entry route the control unit will give an audible internal alarm in place of the
normal entry tone.
41: Bell Delay
When the system is set and (for example) an intruder violates a zone, then
the system waits for the programmed Bell Delay before operating the external
sounder. The system then operates the external sounder for the programmed
Bell Duration. See “Programming Commands” for the Command options.
42: Bell Duration
This Command lets you set the length of time the system will operate the
external sounder during an alarm. See “Programming Commands” for the
Command options.
43: Level A Entry Time
This Command lets you set the Entry Time for Full Set. See “Programming
Commands” for the Command options. The time starts when a user opens
any Final Exit zone.
44: Level A Exit Time
This Command lets you set the Exit Time for Full Set. See “Programming
Commands” for the Command options.
45: Entry/Exit Tone Volume
Use this Command to set the volume of entry/exit tones from the internal
sounder. If you select option 0 then the internal sounder gives no entry/exit
tones. If you select option 1 then the internal sounder gives quiet entry/exit
496929 Page 35
4. Programming
tones, while option 9 gives the loudest entry/exit tones. The internal sounder
demonstrates the volume of the tone when you enter the digit.
46: Tamper Alarm Annunciation
Use this Command to chose which sounders the control unit will activate for a
tamper alarm while the system is unset.
Option
0 Selects internal sounders only.
1 Selects keypad sounders only.
2 Selects internal sounders and keypad sounders.
50: CSID Code
To allow the customer to use the ‘Remote Reset’ facility, you must program
the control unit as ‘Engineer Reset’ (Command 33 option 1) and then install a
four digit Central Station Identification (CSID) code.
First make contact with the ARC and obtain the CSID code. Then ensure that
the system is in programming mode. Next, key in:
50 Y nnnn Y
Where nnnn is the "CSID Code".
The control unit now contains the same CSID code as the ARC. After an
alarm the control unit can generate a ‘Reset Code’ which will be recognised
by the ARC 7300 Remote Reset decode programmer.
After an alarm the user keys in their access code to silence the alarm, but
cannot reset the system. The system generates a four digit code number and
displays it on the keypad. The user calls the ARC and tells them the number
shown on the keypad display. The ARC verifies the user's identity, then enters
the code number into a special programmer. The programmer generates an
‘Anti Code’, which the ARC gives back to the user. The user then enters the
‘Anti Code’ at the keypad to reset the system.
Note: To delete a CSID code key in “0000” over the existing code.
3. Key in two digits for the day number and press Y. Use a leading zero for
the first nine days of the month.
Page 36 496929
4. Programming
4. Key in the two digits for the month number and press Y . Use a leading
zero for January to September.
5. Key in the two digits of the year and press Y.
The display shows the current time, for example: H09 M15
6. Key in two digits for the hours of the day and press Y. Use the 24-hour
clock.
7. Key in two digits for the minutes and press Y.
The keypad sounder gives a double “bleep” and the display shows
“Installer Mode”. The system sets its internal clock/calendar to the time
you have given it.
Option
0 The control unit omits alarm contacts only
1 The control unit omits both alarm and tamper contacts when the user
omits a zone.
53: Abort Reset
Option
0 Ensures that reset after abort is the same as system reset (see
Command 33).
1 Enables customer reset after an abort.
60: Level B Final Exit Operation
Command 60 controls how the system will treat Final Exit zones in part set
Level B. When the Command option is set to 0 any Final Exit zones included
in part set B will continue to act as Final Exit zones during part set B. When
the option is set to 1 any Final Exit zones included in part set B will act as
Normal Alarm zones during part set B.
61: Level B Entry Route Response
Command 61 controls how the system treats Entry Route zones during part
set B. When the option is set to 0 all Entry Route zones included in part set B
will continue to act as Entry Routes during part set B. When the option is set
496929 Page 37
4. Programming
to 1 any Entry Route zones included in part set B will act as Final Exit zones
during part set B.
62: Level B Exit Mode
Command 62 specifies the exit mode for Level B.
Option
0 Low Tone. Timed set with the exit tone fixed at half volume.Use
Command 65 to select the exit time.
1 Instant Set (no exit tone)
2 Silent Set. (Timed Set with no exit tone) .Use Command 65 to
program the Exit time.
3 As A. The exit mode chosen for Level A (whole system) is also
applied to this level.
Note: The keypads give a double beep confirmation tone at the end of all
setting modes.
Page 38 496929
4. Programming
496929 Page 39
4. Programming
0 Low Tone. Timed set with the exit tone fixed at half volume. Use
Command 79 to select the exit time.
1 Instant Set (no exit tone)
2 Silent Set. (Timed Set with no exit tone ).Use Command 79 to
program the Exit time.
3 As A. The exit mode chosen for Level A (whole system) is also
applied to this level.
Note: That the keypads give a double beep confirmation tone at the end of all
setting modes.
77: Level D Alarm Response
Command 77 specifies the alarm response for Level D.
Option
0 Keypad sounders only.
1 Internal sounders and keypad sounders.
2 Local alarm (internal and external sounder only).
3 Full alarm (communication outputs and internal/external sounders).
78: Level D Entry Time
This Command sets the entry time for Level D. See “Programming
Commands” for options.
79: Level D Exit Time
This Command sets the exit time for Level D. See “Programming Commands”
for options.
81, 82, 83, : Output Programming
The system has three transistorised, high current, programmable outputs.
Command 81 programs output 1, Command 82 programs output 2 and,
Command 83 programs output 3. All three Commands take a single following
digit that selects the function.
Note: The outputs are a "pull down” type that provide negative applied control
signals. The outputs float(neither + or -) when inactive, and 0V when
active.
Page 40 496929
4. Programming
Output Type
Option
00 Bell. - The control unit operates this output during an alarm. Use
Command 41 to control bell delay and 42 to control bell duration.
01 EE Follow. - This output is active when the entry or exit time starts
and deactivates at the end of the entry/exit time, or if the entry/exit
time is terminated. The output can be used for a separate entry/exit
buzzer. Note that the output does not give a tone during part set if the
exit mode is silent set or instant set.
02 Armed lamp. - The output is active continuously while the system is
full or part set.
03 PIR Set Latch. - This output is active when the system is set and
deactivates when the system is unset or an alarm condition occurs.
The output will also activate for one second when a reset is performed
or the control unit leaves programming mode. In addition, the output is
active during a walk test.
04 Shock Reset. - This output is used to reset shock sensors, (for
example the ‘Viper or Trapper’). The control unit triggers the output at
the start of the exit period. The output remains active for a fixed time
of five seconds.
05 Walk Test. - This output is active during both engineer and user walk
test and in the period between silencing the system and resetting the
system. This output type is used on movement detectors which have
the facility to switch off the walk test LED in any state other than a
walk test.
06 Ready Lamp. - (System is Clear to Set) This output is active when the
system is unset, and if there are no faults. The output is inactive when
the system is full or part set, during any alarm, or if a circuit fault
prevents setting (Final Door and Entry Route zone types are ignored).
Note: The output will also be active when the control unit is in programming
mode.
496929 Page 41
4. Programming
output for 3 seconds when the system is reset after any alarm has
occurred.
10 Siren Test. - This output becomes active when the Installer performs a
sounder test using Command 91.
11 Strobe Set. - This output is active for 10 seconds after the system has
set. The output can be used to operate the strobe to give a visual
indication that the system has completed setting.
Page 42 496929
4. Programming
496929 Page 43
4. Programming
3. Press 1. (You can press X to stop the procedure if you change your mind
at this stage.)
4. Press Y.
The keypad gives a double confirmation tone and the system loads the
factory default Command values, erasing all previously programmed
values.
Note: The log is protected and cannot be erased by the Installer.
2. Press Y.
The display shows: Checking System
and after a few seconds the control unit
resets itself and returns to user mode.
If any 24 hour, Fire, PA or Technical zones or any tamper switches are active
when you try to leave
programming mode then the keypad gives an error tone and displays all the
faults.
Clear the faults shown on the display and press Y. Repeat steps 1 and 2 and
the control unit should leave programming mode.
Page 44 496929
4. Programming
496929 Page 45
4. Programming
1 +ve Applied to trigger. The inactive output floats. When active the output
goes +ve.
170 - 175: Pulsed Set & Unset Output Options
Use commands 170 to 175 to apply additional options to the output types
pulsed set o/p 1-4 and pulsed unset o/p 1-4.
Example 1: Panel output 3 is programmed with the output type 12 (Pulsed set
o/p 1). This is required to operate a locking mechanism when the system is
set. The locking system requires a pulsed trigger time of 6 seconds
(command 170 - Set o/p 1 is programmed as 06 seconds). This is only to be
applied when the whole system is set. Select level A in command 171 Set
O/p 1).
The programming sequence for the physical panel output no. 3 is:
Command 83 = 12 (Output type - Pulsed Set o/p 1)
Command 170 = (set 1 = 06) seconds
Command 171 = (set 1 = a) level
Example 2: Panel output 3 is programmed with the output type 13 (Pulsed
Unset o/p 1). This is required to operate an unlocking mechanism when the
system is set. The unlocking system requires a pulsed trigger time of 8
seconds (command 172 - Set o/p 1 is programmed as 08 seconds). This is
only to be applied when the whole system is Unset. Select level A in
command 173 Set O/p 1). In addition if a Fire or PA alarm occurs then the
output will be active for the programmed time.
The programming sequence for the physical panel output 3 is: -
Command 83 = 13 (Output type - Pulsed Unset o/p 1)
Command 172 = (set 1 = 08) seconds
Command 173 = (set 1 = a) level
Command 174 = (Fire o/p 1) active if Fire alarm
Command 175 = (PA o/p 1) active if PA alarm
The Pulsed set o/p commands are:
(use tick key to scroll round o/p 1-4)
170 Set o/p 1 Time, select a time in the range 01-12 seconds
Set o/p 2 Time, select a time in the range 01-12 seconds
Set o/p 3 Time, select a time in the range 01-12 seconds
Set o/p 4 Time, select a time in the range 01-12 seconds
171 Set o/p 1 ABCD, select the level(s) in which the output will be active,
toggle abcd keys to select level on /off.
Set o/p 2 ABCD, select the level(s) in which the output will be active
toggle abcd keys to select level on /off.
Page 46 496929
4. Programming
Set o/p 3 ABCD, select the level(s) in which the output will be active
toggle abcd keys to select level on /off.
Set o/p 4 ABCD, select the level(s) in which the output will be active
toggle abcd keys to select level on /off.
172 Unset o/p 1 Time, select a time in the range 01-12 seconds
Unset o/p 2 Time, select a time in the range 01-12 seconds
Unset o/p 3 Time, select a time in the range 01-12 seconds
Unset o/p 4 Time, select a time in the range 01-12 seconds
173 Unset o/p 1 ABCD, select the level(s) in which the output will be active,
toggle abcd keys to select level on /off.
Unset o/p 2 ABCD, select the level(s) in which the output will be active,
toggle abcd keys to select level on /off.
Unset o/p 3 ABCD, select the level(s) in which the output will be active,
toggle abcd keys to select level on /off.
Unset o/p 4 ABCD, select the level(s) in which the output will be active,
toggle abcd keys to select level on /off.
174 Fire o/p 1, Select as on if O/P 1 is to respond if a Fire alarm occurs
Fire o/p 2, Select as on if O/P 2 is to respond if a Fire alarm occurs
Fire o/p 3, Select as on if O/P 3 is to respond if a Fire alarm occurs
Fire o/p 4, Select as on if O/P 4 is to respond if a Fire alarm occurs
175 PA o/p 1, Select as on If O/P 1 is to respond if a PA alarm occurs
PA o/p 2, Select as on If O/P 2 is to respond if a PA alarm occurs
PA o/p 3, Select as on If O/P 3 is to respond if a PA alarm occurs
PA o/p 4, Select as on If O/P 4 is to respond if a PA alarm occurs
Note: For options 174 to 175 use 1 for ON and 0 for OFF.
496929 Page 47
5. Testing
Reading the Log (Command 90)
The control unit keeps a log of recent events The log can contain up to 250
events. Each event is represented by a short text message, shown below and
on the next page. To review the event log, make sure the system is in
programming mode, then:
1. Key in 90Y.
The display shows the most recent event in the log. For a list of the log
messages see below.
2. Key in 1 to show earlier events or 3 to see more recent events.
3. Press Y to toggle between the event message and the event time.
4. Press X to leave the log.
The table below and on the next page shows all the messages that can
appear in the event log. The left hand column shows the messages that
appear on a keypad display.
Note: Each event in the log is accompanied by the date and time in numerical
format.
Neither the Installer nor the user can erase the log.
In the log user codes are represented by numbers as follows:
U00 Installer U19 Idle
U01 User code 1
... ... U21 Keyswitch
U16 User code 16 U22 Remote Reset
U17 Duress code
U18 Control Unit
Keypad and Event Log Displays
Keypad Meaning
AC Fail Mains supply failed
AC Restore Mains supply restored
Alarm Abort User aborted alarm
Aux DC Fail Aux power failed
Aux DC Fail Rstr Aux power restored
Bad Checksum The control unit has detected data corruption in its memory
Batt Missing Battery disconnected
Batt Missing Rstr Battery re-connected
Burg Znn Alarm Intruder alarm on zone nn
Burg Znn Rstr Instruder alarm on zone nn restored
Codes Defaulted User access codes and installer code returned to default values
Defaults Loaded All programming defaults loaded
Page 48 496929
5. Testing
Keypad Meaning
EEProm Fail Control unit memory damaged
Fire Znn Alarm Fire alarm on zone nn
Fire Znn Reset Fire alarm on zone nn reset
Fire Znn Rstr Fire alarm on zone nn restored
Knn Excess Keys User has tried to enter access code too many times on keypad nn
Knn Missing Keypad nn disconnected
Knn Restore Keypad nn re-connected
Knn Tamper Tamper alarm on keypad nn
Tamper Knn Restr Tamper alarm on keypad nn
Fr Knn Alarm Fire alarm started at keypad nn
Md Knn Alarm Medical alarm started at keypad nn
Key Sw Set Znn System set by keyswitch on zone nn
Key Sw UnsetZnn System unset by keyswitch on zone nn
Key Box Cls Znn Keybox on zone nn closed
Key Box Opn Znn Keybox on zone nn opened
Lid Tamp Rst Control unit lid tamper alarm restored
Lid Tamper Control unit lid tamper alarm
Low Batt Rstr Control unit low battery restored
Low Battery Low battery on control unit
PA Knn Alarm Panic alarm raised from keypad nn
PA Znn Alarm Panic alarm raised from zone nn
PA Znn Rstr Panic alarm on zone nn restored
Set Fail Znn System setting failed because of fault on zone nn
Smk Det Alm Znn Smoke detector alarm on zone nn
Smk Det Res Znn Smoke detector on zone nn restored
Soak Fail Znn Soak fail test on zone nn caused alarm
Sounder Tamp Rst Tamper on sounder restored
Sounder Tamper Sounder tamper
System Rearmed System rearmed
System Startup Power applied to system
Tamper Znn Zone nn tamper alarm
Tamper Znn Rstr Tamper alarm on zone nn restored
Tech Znn Alarm Technical alarm on zone nn
Tech Znn Rstr Technical alarm restored on zone nn
Tel Line Fault Telephone line fault detected
Tel Line Rstr Telephone line restored
Unn Change Unn User nn changed access code for user nn
Unn Delete Unn User nn deleted access code for user nn
Unn Off-Site Engineer exited programming mode
Unn On-Site Engineer entered programming mode
Unn System Reset User nn reset system
Unn System Set User nn set system
Unn System UnSet User nn unset system
Unn Time/Date User nn changed the time and date
Unn Znn Omit User nn omitted zone nn
Unn Znn Unomit User nn un-omitted zone nn
496929 Page 49
5. Testing
Page 50 496929
Index
496929 Page 51
using ......................................................................14 Start up ......................................................................18
PA reset......................................................................33 Status display............................................................. 32
Panic Alarm ................................................................27 Strobe ........................................................................ 41
PCB ..............................................................................7 testing .................................................................... 50
Plug by communicator outputs ...................................45 Strobe set................................................................... 42
Power Strobe while setting.................................................... 42
Control unit current ..................................................6 System tamper reset .................................................. 34
Programming commands ...........................................20 Tamper alarm annunciation ....................................... 36
Programming mode ....................................................20 Tamper communication.............................................. 33
leaving .............................................................24, 44 Tamper return .............................................................. 6
re-entering .............................................................25 Technical.................................................................... 28
Pulse Set ....................................................................42 Tellback........................................................................ 6
Pulse Unset ................................................................42 Tellback reset............................................................. 31
Ready lamp ................................................................41 Terminate................................................................... 34
Reset Testing ....................................................................... 48
after abort ..............................................................37 Time and date ............................................................ 36
engineer.................................................................24 Timed ......................................................................... 34
RedCare ..................................................................6 User codes ................................................................. 20
remote....................................................................36 Walk test .............................................................. 41, 50
shock .....................................................................41 Weight.......................................................................... 6
tellback...................................................................31 Zone
Sensitivity ...................................................................30 attributes................................................................ 29
Set latch .....................................................................41 description ............................................................... 5
Shock analyser...........................................................28 names.................................................................... 26
Shock reset ................................................................41 programming ......................................................... 26
Silent or audible PA ....................................................32 types ...................................................................... 27
Siren test ....................................................................42 wiring ..................................................................... 13
Smoke detector ..........................................................28 Zone configuration ..................................................... 31
Smoke reset ...............................................................41 Zone Name ................................................................ 30
Soak Test ...................................................................29 deleting .................................................................. 26
Sounders ....................................................................12 Zone tamper reset...................................................... 32
Specification .................................................................6
Page 52 496929
Notes
496929 Page 53
Declaration of Conformance
Cooper Security Ltd issues this certificate to
certify that the equipment known as:
9651
Complies with the following directive:
1995/5/EC R&TTE Directive
Signed