IP3701 Install
IP3701 Install
IP3701 Install
IP3701H-2 Series
IP Color Camera
C2941M-B (4/08)
Contents
Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Camera Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Reset Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Lens Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Camera Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wiring Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cat5 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
24 VAC and BNC Connections (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Dynamic Range and EDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
C2941M-B (4/08) 3
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Only use attachments/accessories specified by the manufacturer.
8. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such
as vases shall be placed on the apparatus.
9. Installation should be done only by qualified personnel and conform to all local codes.
10. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be installed where exposed to rain and moisture.
11. Use only installation methods and materials capable of supporting four times the maximum
specified load.
12. Use stainless steel hardware to fasten the mount to outdoor surfaces.
13. Only use replacement parts recommended by Pelco.
14. After replacement/repair of this unit’s electrical components, conduct a resistance measurement
between the line and exposed parts to verify the exposed parts have not been connected to the line
circuitry.
The exact terms of GPL, LGPL, and some other licenses are provided to you with this product. Please refer
to the exact terms of the GPL and LGPL at http://www.fsf.org (Free Software Foundation) or
http://www.opensource.org (Open Source Initiative) regarding your rights under said license. You may
obtain a complete corresponding machine-readable copy of the source code of such software under the
GPL or LGPL by sending your request to digitalsupport@pelco.com; the subject line should read Source
Code Request. You will then receive an e-mail with a link for you to download the source code.
This offer is valid for a period of three (3) years from the date of the distribution of this product by Pelco.
4 C2941M-B (4/08)
Regulatory Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve
Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,
Washington D.C. 20402.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment
can void your authority to operate this equipment under Federal Communications Commission’s rules.
Judgment as to the suitability of the products for users’ purposes is solely the users’ responsibility. Users
shall determine the suitability of the products for their own intended application, picture rate and picture
quality. In the event users intend to use the video for evidentiary purposes in a judicial proceeding or
otherwise, users should consult with their attorney regarding any particular requirements for such use.
C2941M-B (4/08) 5
Description
The IP3701H-2 Series is a high resolution, color video camera with a built-in 100Base-TX network interface
for live streaming to a standard Web browser (Microsoft® Internet Explorer® or Firefox®). The camera
features open architecture connectivity for third-party software recording solutions and is also Endura
Enabled™ to record, manage, configure, and view multiple live streams.
The camera also includes built-in Power over Ethernet (PoE), which supplies power to the camera through
the network. If PoE is not available, the camera is prewired for 24 VAC.
Before installing your camera, thoroughly familiarize yourself with the information in this manual.
MODELS
IP3701H-2 High resolution, 480 TV lines, SuperHAD™ CCD, minimum illumination of 0.5 lux at f/1.2 and
40 IRE, NTSC
IP3701H-2X High resolution, 470 TV lines, SuperHAD CCD, minimum illumination of 0.5 lux at f/1.2 and
40 IRE, PAL
6 C2941M-B (4/08)
Basic System Configurations
IMPORTANT NOTE. PLEASE READ. The network implementations in this document are shown as
general representations only and are not intended to show detailed network topologies. Your actual
network will differ, requiring changes or perhaps additional network equipment to accommodate the
systems as illustrated. Please contact your local Pelco Representative to discuss your specific
requirements.
CAMERA
ENDURA
WEB
BROWSER
CAMERA
C2941M-B (4/08) 7
NETWORK SWITCH
(FOR EXAMPLE
169.254.200.0)
CAMERA
(FOR EXAMPLE
PRIVATE NETWORK 169.254.200.1)
PC ACTS AS SERVER CAMERA
STATIC NETWORK
(FIXED BUT UNIQUE IP ADDRESS; NOTE: FOR A SECURE NETWORK, PELCO RECOMMENDS
SAME SUBNET MASK AS CAMERAS) PLACING THE IP3701H SERIES CAMERA BEHIND A FIREWALL.
8 C2941M-B (4/08)
Camera Layout
TOP MOUNT
LENS LEVEL ADJUSTMENT
NETWORK CONNECTOR
POWER CONNECTOR
LEDs
RESET BUTTON
BACK FOCUS
ADJUSTMENT RING
BACK FOCUS ADJUSTMENT
LOCKING SCREW
BNC VIDEO SERVICE CONNECTOR
LENS CONNECTOR
DIP SWITCHES (COVER REMOVED)
RESET BUTTON
Use the reset button located on the side of the camera to access the following modes:
Table A. Reset LED Status
NOTES:
• If there is no configuration activity for 15 minutes, the camera will automatically exit the reset
mode.
• The LED is not lit during normal operation.
C2941M-B (4/08) 9
Installation
LENS MOUNTING
The camera can be used with a fixed iris, manual iris, or auto iris lens. The camera is factory set for a
CS mount lens, but is easily adjusted for a C mount lens.
1. C mount lens only: Completely rotate the back focus adjustment counterclockwise before
installing the C mount lens (refer to Back Focus Adjustment on page 15).
2. Set the lens mode selector switch on the side of the camera to AIV (auto iris video drive) lens or AID
(auto iris DC drive) lens. Refer to Switch Settings on page 16. Switch settings are determined by the
type of lens used.
3. Screw the lens onto the lens mount. Be careful to prevent dust from entering the space between the
lens and the CCD element. If necessary, use clean compressed air to remove any foreign matter.
4. Connect the auto iris lens to the 4-pin connector located on the side of the camera. Pin connections
for the iris drive connector are as follows:
PIN DC (AID) AUTO IRIS LENS VIDEO (AIV) AUTO IRIS LENS
3 4
1 Control coil negative (-) Lens positive supply
2 Control coil positive (+) Not used
3 Drive coil positive (+) Video drive signal
1 2 4 Drive coil negative (-) Ground
CAMERA MOUNTING
Use a standard 1/4-20 screw (provided) with a maximum thread length of 3/8-inch (10 mm) for mounting to
the top or bottom of the camera.
10 C2941M-B (4/08)
Wiring Tables
CAT5 CABLE
Connect a Cat5 cable to the RJ-45 network connector. The 8-pin connector includes video and PoE for the
camera. PoE (IEEE 802.3af) injects power over the same cabling that carries the network data, eliminating
the need for a separate power supply. This simplifies the installation and operation of the camera without
any degradation of network performance.
Pin Function
1 TX+
2 TX- 1 8 8
3 RX+
1 2 3 4 5 6 7 8 8
7
1
6
4 PoE 1-2 5
4
3
2
1
5 PoE 1-2
6 RX-
7 PoE 3-4
8 PoE 3-4
The power supply connector is shown in Figure 6. Use only a Class 2 isolated power supply. Refer to
Specifications on page 21 for power consumption.
CLASS 2
ISOLATED
POWER
SUPPLY
24 VAC
C2941M-B (4/08) 11
The following are the recommended maximum distances for 24 VAC applications and are calculated with a
10-percent voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC-powered
devices.)
Table C. Recommended Wire Gauge and Wiring Distances
Total 20 18 16 14 12 10
VA (0.5 mm2) (1.0 mm2) (1.5 mm2) (2.5 mm2) (4.0 mm2) (6.0 mm2)
10 283 451 716 1142 1811 2880
(86) (137) (218) (348) (551) (877)
For example, a camera that requires 10 VA and is installed 283 ft (86 m) from the transformer would
require a minimum wire gauge of 20 AWG.
NOTE: Wire gauges are standard AWG or metric sizes. Distances are calculated in feet; values in
parentheses are meters.
12 C2941M-B (4/08)
Lens Setup and Focus Procedures
VIDEO DRIVE AUTO IRIS LENS
1. Set the lens mode selector switch to AIV.
2. Switch the electronic shutter control (ESC) and automatic gain control (AGC) OFF.
3. Refer to the lens instructions and adjust the lens for the optimum picture (video output level of
1 Vp-p).
4. Focus the lens.
a. Completely open the iris by covering the lens with a suitable neutral density ND filter.
b. If the viewed scene is 6.5 ft (2 m) away or farther, set the lens focus to infinity (far).
c. Use the back focus adjustment ring (refer to Back Focus Adjustment on page 15) and focus on
the selected scene.
d. Remove the ND filter and set the lens focus as required.
5. Set the AGC switch to ON, as required. Most scenes benefit from AGC.
C2941M-B (4/08) 13
MANUAL IRIS LENS
1. Set the ESC and AGC switches to ON (default settings).
2. Focus the lens.
a. Open the iris fully and set the lens focus to infinity.
b. View an image more than 6.5 ft (2 m) away.
c. Focus the image with the back focus adjustment ring (refer to Back Focus Adjustment on
page 15).
d. Adjust the lens focus and set the iris (if equipped) for the best picture quality. The largest
aperture gives the best light sensitivity; the smaller the aperture, the greater the depth of
field.
ZOOM LENS
1. Set the lens focus to infinity (far) and completely open the iris by covering the lens with a suitable
ND filter
2. Zoom out to the widest field of vision and view a distant object.
3. Adjust the back focus adjustment ring until the object is in focus (refer to Back Focus Adjustment on
page 15).
4. Zoom in completely and adjust the lens focus until the object is again focused.
5. Repeat these steps until the full zoom range may be viewed with the minimum loss of focus.
14 C2941M-B (4/08)
Back Focus Adjustment
The back focus adjustment is located at the front of the camera and is accessible from either side of
the case.
WISE
OCK
RCL
NTE
COU
BACK FOCUS
ADJUSTMENT
BACK FOCUS LOCKING SCREW
ADJUSTMENT
ISE
RING CKW
CLO
C2941M-B (4/08) 15
Switch Settings
NOTES:
• White indicates the switch setting.
• Under most conditions, you will not be required to set any switches.
16 C2941M-B (4/08)
t Not Used
u Extended dynamic range (EDR)
OFF (default setting): Disables the EDR mode.
EDR: Enables the EDR mode to help balance a scene with a large dynamic range. Use this feature
to improve the picture in washed-out areas. This feature adds 12X the dynamic range, but also
increases dark area picture noise. Refer to Dynamic Range and EDR on page 17 for further details.
~í Automatic white balance (AW1/AW2)
AW1 (default setting): Automatically processes the viewed image to retain color balance over a
wide color temperature range.
AW2: Processes the viewed image to retain color balance in a restricted color temperature range.
Use only when AW1 causes an unbalanced color picture.
C2941M-B (4/08) 17
Dynamic Range and EDR
Dynamic range is the ratio between the brightest and darkest parts of an image or scene. A scene that
ranges from bright sunlight to deep shadows has a high dynamic range, while indoor scenes with less
contrast have a low dynamic range.
The extended dynamic range (EDR) feature will help capture the entire range of the scene. This feature can
achieve 12X the improvement in dynamic range. In scenes with very high dynamic range, the EDR feature
will exhibit a higher noise level than when the feature is turned off. This is normal and is not a
malfunction.
NOTE: Depending on the scene contrast, it may or may not be possible to capture the entire range with
any camera. Careful camera placement should be considered in extreme cases.
18 C2941M-B (4/08)
Troubleshooting
Power issue (24 VAC) • Verify the 24 VAC power supply connection.
• Disconnect the network cable and then reconnect
it to the camera. Power is indicated by the LED.
The LED will flash (green) five times per second for
approximately two minutes if the camera has
power.
Image too dark/ Installation error • Make sure the lens cover in not installed.
black image • Make sure camera is not located in an environment
with zero light.
• Use a service connector to check camera
operation. Connect one end of the service
connector to the BNC service connector on the
camera. Connect the other end of the service
connector to a monitor.
• Replace camera with a working camera. If the new
camera does not work, contact Pelco Product
Support at 1-559-292-1981 or 1-800-289-9100.
C2941M-B (4/08) 19
Problem Possible Cause Suggested Remedy
20 C2941M-B (4/08)
Specifications
GENERAL
Construction
Finish Black polyester powder coat
Imaging Device 1/3-inch imager
Picture Elements
IP3701H-2 768 (H) x 494 (V)
IP3701H-2X 752 (H) x 582 (V)
Sensing Area 6 mm diagonally
Horizontal Resolution 480 TV lines
Iris Control Electronic/passive
Minimum Illumination 0.5 lux, f/1.2, 40 IRE, AGC on, 75% reflectance
ESC 1/60 to 1/100,000 second
Signal-to-Noise Ratio 52 dB (AGC off)
Backlight Compensation Selectable by DIP switch setting
Scanning System
IP3701H-2 525 lines, 2:1 interlace
IP3701H-2X 625 lines, 2:1 interlace
Auto Iris Lens Type DC/video control, selectable by DIP switch position
Unit Weight 2.2 lb (1.0 kg)
ELECTRICAL
Ports RJ-45 connector for 100Base-TX
Auto MDI/MDI-X
Autonegotiate/manual setting
Cabling Type Cat5 or better for 100Base-TX
Input Voltage 24 VAC (18-30) or PoE (IEEE802.3af)
Power Consumption 7 W maximum
MECHANICAL
Lens Mount C/CS mount (adjustable)
Camera Mount Use 1/4-20 screw, top or bottom of camera housing
VIDEO
Signal System NTSC or PAL
Compression MPEG-4, MJPEG in Web viewing mode
Video Streams 3, simultaneous
Video Resolutions NTSC PAL
4CIF 704 x 480 704 x 576
2CIF 704 x 240 704 x 288
CIF 352 x 240 352 x 288
QCIF 176 x 120 176 x 144
Bit Rate Configurable 20 kbps to 2 Mpbs per stream, implements EnduraView™
Video Access from
Web Browser Camera live view for up to 10 video sources
Users 10 simultaneous users, unlimited number of users using multicast
Minimum Web Browser
Requirements PC (Pentium® 4 microprocessor, 1.6 GHz) with
Windows® 98, Windows 2000, Windows XP (or later), or
Mac® OS X 10.3.9 (or later)
RAM 512 Mbyte
Ethernet Card 100 Mbit
Web Browser Internet Explorer 5.5 (or later) or Firefox 1.5 (or later)
Screen Resolution 1024 x 768 pixels or higher, 16- or 32-bit pixel color resolution
C2941M-B (4/08) 21
ENVIRONMENTAL
Operating Temperature 14° to 122°F (-10° to 50°C)
Storage Temperature 14° to 158°F (-10° to 70°C)
PHYSICAL
Dimensions 4.54" D x 2.64" W x 3.06" H
(11.53 x 6.71 x 7.77 cm)
Weight (without lens) 1.01 lb (0.46 kg)
The materials used in the manufacture of this document and its components are compliant to the requirements of
Directive 2002/95/EC.
This equipment contains electrical or electronic components that must be recycled properly to comply with
Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment
(WEEE). Contact your local dealer for procedures for recycling this equipment.
22 C2941M-B (4/08)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.
Exceptions to this warranty are as noted below:
• Five years on fiber optic products and TW3000 Series unshielded twisted pair (UTP) transmission products.
• Three years on Spectra® IV products.
• Three years on Genex® Series products (multiplexers, server, and keyboard).
• Three years on DX Series digital video recorders, DVR5100 Series digital video recorders, DigitalSENTRY® Series hardware products, DVX Series
digital video recorders, NVR300 Series network video recorders, and Endura® Series distributed network-based video products.
• Three years on Camclosure® and Pelco-branded fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.
• Three years on PMCL200/300/400 Series LCD monitors.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
• Two years on Spectra III™, Spectra Mini, Esprit®, ExSite®, and PS20 scanners, including when used in continuous motion applications.
• Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).
• Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of
90 days. The air filter is not covered under warranty.
• Two years on Intelli-M® eIDC controllers.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners, or preset lenses used in continuous motion applications (preset scan, tour, and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to a Pelco designated location. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the
Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or
consequential damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair) and designated return location.
All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid.
1-8-08
REVISION HISTORY
Manual # Date Comments
C2941M 8/07 Original version.
C2941M-A 1/08 Added Open Source Software Notice.
C2941M-B 4/08 Removed referenced to JRE per CN21185.
Pelco, the Pelco logo, Camclosure, DigitalSENTRY, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.
Spectra III is a trademark of Pelco, Inc. © Copyright 2008, Pelco, Inc. All rights reserved.
DLP is a registered trademark of Texas Instruments Incorporated.
Microsoft, Windows, and Internet Explorer are registered trademarks of Microsoft Corporation.
Firefox is a registered trademark of the Mozilla Foundation.
Pentium is a registered trademark of Intel Corporation.
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
www.pelco.com
ISO9001
Australia | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore
South Africa | Spain | Sweden | United Arab Emirates | United Kingdom | United States