B.Tech Project Report
B.Tech Project Report
B.Tech Project Report
TECH PROJECT
REPORT PREPARATION
Introduction
This document is intended to provide a set of specific and uniform
guidelines to the B. Tech students in the preparation of the eighth semester project
report. The content of the report, which is submitted to the Institute in partial
fulfillment for the award of the degree of Bachelor of Technology, is very much
important. It is also imperative that the report, to be acceptable by the Institute,
should essentially meet a uniform format emphasizing readability, concordance
with ethical standards and Institute-wide homogeneity.
2
CHAPTER 1
REPORT LAYOUT
1. COVER PAGE: See sample sheet 1. The content, relative font size and
locations of various items in the page should match with those given in
sample sheet 1. All copies to be submitted to the various offices at IIST
should be soft bound with white cardboard and black rexin in spine.
3
3. CERTIFICATE: See sample sheet 2. The content, relative font size
and locations of various items in the page should match with those given
in sample sheet 2.
4
CHAPTER 2
GENERAL GUIDELINES
2.4. Margins
A margin of 35 mm is to be provided on left and right sides, whereas top
and bottom margins should be 30 mm. No print matter should appear in the
margin except the page numbers. All page numbers should be centered inside the
bottom margin, 20mm from the bottom edge of the paper. Right margin should be
20 mm.
2.5. Font
Times New Roman (TNR) 12 point font has to be used throughout the
running text. The captions for tables and figures should have font size of 11 and
foot notes should be set at font size 10. Font sizes for various levels of headings
are given in section 2.7.
5
2.6. Line Spacing
The line spacing in the main text should be 1.5. Single line spacing
should be given for quotations, abstract, figure captions, table captions, figure
legends, footnotes, and references. The equations, tables, figures, and quotations
should be set off from the main text both before and after with spacing of 1.5.
Two consecutive paragraphs should be separated by triple line spacing.
2.7. Headings
Following format has to be followed in heading of chapters and sections.
CHAPTER 3
TITLE PAGE-CENTERED TNR 16-POINT BOLD ALL CAPS
6
Running text should be set in 12-point TNR and fully justified. First line
of paragraph should have indentation of 15 mm.
7
2.9. Citing References
[1]
Citation should be given to the referred points in the paragraph like
this.
2.10.1. Journals
1. Prakas, K. (2011). Feedback and optimal sensitivity: Model reference
transformations, multiplicative seminorms, and approximate inverses. IEEE
Transactions on Automatic Control, 26(2): 301–320.
2. Ram, R., Krishna, S. and Peter, K. (2005a). Risk sensitive estimation and a
differential game. IEEE Transactions on Automatic Control, 39(9): 1914–
1918.
4. Ram, R., Krishnamurthy, P., Prasad, N. and Peter, K. (2009). Risk sensitive
estimation model II. IEEE Transactions on Automatic Control, 43(15):
355 - 363.
8
2.10.2. Text books
1. Myers, D. G. (2007). Psychology (1st Canadian ed.). Worth: New York.
2.10.4. Reports
1. Milton, M and Robert, L. (2004). Atmospheric carbon emission through
genetic algorithm, Environment and Technical Report No.3., Indian
Meteorological Department., New Delhi.
9
2.10.9. Chapters from a book
1. Krebs, D.L. and Denton, K. (1997). Social illusions and self deception: The
evolution of biases in person perception. In J. A. Simpson & D. T. Kenrick
(Eds.), Evolutionary social psychology (pp.21-48). Hillsdale, NJ: Erlbaum.
10
the left. If the end of a chapter is in odd page (right side page) the next chapter
should start on odd page i.e., on a fresh paper, and should be numbered as odd
only by counting the blank even page also. However, the page number is not
printed on the blank pages.
2.12. Printing
Printing of all material in general should be double –sided in black ink
with exceptions as indicated in sections 2.3 and 2.11.
2.14. Binding
Thesis copies to be submitted for evaluation are to be soft bounded. The
cover page should be printed on glossy white card of 300 g/m2 or above.
11
A
Project Report on
Submitted by,
12
DR. BABASAHEB AMBEDKAR TECHNOLOGICAL UNIVERSITY
LONERE, RAIGAD, MAHARASHTRA-402103
DEPARTMENT OF ELECTRICAL ENGINEERING
CERTIFICATE
This is to certify that Project entitled “DESIGN AND DEVELOPMENT OF GTEM
Examiners:
1]
2]
Date:
13
ACKNOWLEDGEMENT
14