Tuto RenOLink Par Nowen - Fr.en

RenoLink
Manual and tutorial
tutorial is consistent with GabiGafu
Renolink is a program based on the DDT2000 and directed by

GabiGafu.
Contact : gabigafu@hotmail.com
This program is compatible with all Renault vehicles,

some Nissan, Opel and some some Mercedes.
This program is not only useful for the changes it can

bring in some computers but also a diagnostic tool.
The probe is compatible with this program is the OBDLink
SX probe
Here's what it looks like:

probe easily found on the net
Launch app
At program
When the program
launch you
comearrive
on on this page
everythingisisok
If everything okyou
youmust
musthave
havethe
the bottom
bottom leftleft the
shownby
message shown bythe
thered
redarrow
arrowififyou
youinstead
insteadthe
the
message of the black arrow is that
that you
you either
either have
have aa
problem with the probe (drivers or no sensor) or while the
ornot
program is no activated. while the program has
probe) or when
been deactivated.
Description of menus and toolbar

file
File:
Vehicles: opens a page

: Opens orwhere you can
a page we can
select a vehiclevehicle
partially
in left
the and
left part
the box
andin which you
case in which
want to you
connect wantright.
partly to connect in part
Opensevery
Open XML: opens all the
f xml files
iles of
xmlallall
boxes, to, find
to find
thethe
oneone
you're
you're
looking
looking
it's it's
bestbest
notnot
to to
go through this mode.
Close: :simply
Simplyprogram.
to exit to exit
communications
Connect: to connect to limp previously

selected.
Disconnect: to disconnect.
first Misc
Manual Requets: send requests to the case, but be

careful you must not do anything with this command
because if you make a mistake it can permanently block
your calculator.
Identification: displays the identifiers of the selected

computer (ref version, calibration ...)
Wine: Plays the case of the wine but also to change the
Clear Log: Clear log that appear at the bottom left at the
diag or otherwise.
Scan
Scan: Opens the page to start the scan

second Misc
Virginizer: This command opens a window in which

there is a drop down menu which are displayed UCH
that can virginiser (in fact they will not be virgin but
rather properties so clear properties) but now old UCH
Laguna 3 and Latitude.
Eps Virginizer: same kind of control as above, but this

one is for DAE
current Clio 3, Modus, Megane / Scenic and Clio 3 4.
Clear properties also.
Keys: This command opens a window in which there is a

drop down menu where you can choose the type of UCH
according to the vehicle and clicking connect in this window
we can see appear the ISK code, PIN code and also the
identifiers of keys or cards assigned to the UCH, if Uch is
blank and therefore without any of the three previous items
a box will be checked with noted near Uch Virgin.
Airbag
Again a window with a drop down menu opens and you

can choose the housing that we need (if present in the
list). It is possible to erase data from a crash only if the
computer is not cheap to replace.
Two small boxes are present in the window, and ECU

Crash Detected To Replace.
tdb
Same principle window with pull-down menu, but here you

can read and write the mileage or read and write eeprom of
the table.
sniffing
This command is made to capture the frames

circulating on the car network (either CAN or K)
therefore .And with an extension cable Y (or other) can
capture frames sent by other probes (eg. AVDI or
CanClip).
ATTENTION This command is for very highly advanced

users do not do anything with this command, there are
risks in calculators but also in hardware.
The icons of the toolbar
Reading and writing config but so requests,

therefore mistrust with queries.
Allows you to control modes on the case (eg

driving windscreen wipers in UCH)
Writes the injectors codes
the injection ECUs.
Can read and clear fault in the selected

computer.
Lets see these boxes
On can network and especially those who
are not seen.

This order is for new
types of ECU (kind Megane3, Clio4, Logan2).
meaning it is a property of DTC
extended to what can be seen
Mileage to the fault occurred.
There are 3 types of DTC
- for old boxes, we find the DTC
As DEF
- Generic defects
- And so the extended defects (extended DTC)
So this command is useful and
used only on vehicles with
the boxes can provide a history of
on the occurrence of DTC.
So much for the presentation and explanation of the tools of
this program.
Now use tutorial.
Connect to a computer
To be connected to a complete vehicle you must click on

or choose the menu and Scan
arrives this window
To see all the computers click on the green arrow
(Scan), but it will be quite long because RenoLink will
attempt to enter into dialogue with all ECU from its
database.
To connect to a specific computer you must specify the

type of network and type of housing, an example with
UCH Scenic 2, to do this check the diag Can (green
diamond at the bottom left) and the ECU menu roll up at
desired kind of computer.
Then click the green arrow Scan and RenoLink will
enter into dialogue with the computer once the
computer recognized it appears in the table above.
Just double click on the line and the files on this case
will be loaded into the left window of the program's
home page.
Close the small window of the Scan and end up

like this:
Now you must click on the green arrow on the toolbar,
RenoLink will connect to the case, can be seen in lower
left it is written (connected to ECU) and here we are
diag with the computer, we can see everything there by
clicking on the lines of the left table.
When the diag is finished you must click on the red
button that appeared in place of the green play
arrow in the toolbar.
Here I hope to have informed you.
nowen

Tuto RenOLink Par Nowen - Fr.en

Uploaded by

Copyright:

Available Formats

Tuto RenOLink Par Nowen - Fr.en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tuto RenOLink Par Nowen - Fr.en

Uploaded by

Copyright:

Available Formats

RenoLink

Manual and tutorial

tutorial is consistent with GabiGafu

Renolink is a program based on the DDT2000 and directed by

This program is compatible with all Renault vehicles,

This program is not only useful for the changes it can

The probe is compatible with this program is the OBDLink

Here's what it looks like:

Description of menus and toolbar

Vehicles: opens a page

Connect: to connect to limp previously

Manual Requets: send requests to the case, but be

Identification: displays the identifiers of the selected

Scan: Opens the page to start the scan

Virginizer: This command opens a window in which

Eps Virginizer: same kind of control as above, but this

Keys: This command opens a window in which there is a

Again a window with a drop down menu opens and you

Two small boxes are present in the window, and ECU

Same principle window with pull-down menu, but here you

This command is made to capture the frames

ATTENTION This command is for very highly advanced

Reading and writing config but so requests,

Allows you to control modes on the case (eg

Writes the injectors codes

the injection ECUs.

Can read and clear fault in the selected

Lets see these boxes

On can network and especially those who

are not seen.

types of ECU (kind Megane3, Clio4, Logan2).

meaning it is a property of DTC

extended to what can be seen

Mileage to the fault occurred.

There are 3 types of DTC

- for old boxes, we find the DTC

- And so the extended defects (extended DTC)

So this command is useful and

used only on vehicles with

the boxes can provide a history of

on the occurrence of DTC.

So much for the presentation and explanation of the tools of

To be connected to a complete vehicle you must click on

To connect to a specific computer you must specify the

Close the small window of the Scan and end up

Here I hope to have informed you.

You might also like