ACCESSORY ORIENTATION CHART ITEM D/S PART NUMBER QTY DESCRIPTION MAT'L. GR. EST. WT.

PAINT CODE
ITEM SERVICE SIZE REF DEGREE RADIUS 1 B 9281D1A2 1 DOME STANDARD INSTALLATION DETAILS N R
67A DOME SKYLIGHT ASSEMBLY STD. 77.86° 32'-5 5/8" [9896.4mm] DESIGN CRITERIA: 2 B 9281D1A3 1 DOME STANDARD INSTALLATION DETAILS (ACC.) N R
DESIGN (PER API 650 12TH EDITION APPENDIX G)
67B DOME SKYLIGHT ASSEMBLY STD. 212.86° 32'-5 5/8" [9896.4mm] 3 - WIREROPESS38 58 WIREROPE n3/8" 7X19 STRAND 300 SERIES SS N -
WIND DESIGN: 105.12 mph [47 m/s] PER IS875 - -
67C DOME SKYLIGHT ASSEMBLY STD. 347.86° 32'-5 5/8" [9896.4mm] 4 3372T45 2 WIRE ROPE CLIP AND THIMBLE KIT 300 SERIES SS N
DESIGN LIFE: 50 YEARS
68 24" SQ. MANWAY ASSY. 24" SQ. [610mm] 270° 44'-11 5/8" [13706.4mm] 5 - 8201T68 1 ROPE GRAB CLIP 3/8" 300 SERIES SS N -
ROOF LIVE LOAD: 20 lbs/ft²
70 24" VENT ASSEMBLY W/ BIRD SCREEN Ø24" [610mm] 32.86° 9'-2 3/4" [2813.2mm] GROUND SNOW LOAD: 0 lbs/ft² 6 B CRGA06 1 CENTER RING TIE OFF 9 N R
71A MAX CLOSED MASTER FLASH Ø8.6" [218mm] 275.65° 47'-7 1/2" [14516.8mm] 0° DESIGN PRESSURE/VACUUM: ATMOSPHERIC 7
71B MAX CLOSED MASTER FLASH Ø20" [20mm] 282.39° 45'-11" [13996mm] OPERATING PRESSURE/VACUUM: ATMOSPHERIC 8 B HC16 81 HUB COVER FOR Ø16" HUBS ALUM 1100-0 3 N -
9 15 DESIGN TEMPERATURE: UP TO 200°F
15 8 9
10
OPERATING TEMPERATURE: AMBIENT -
15
15 10 B 9281D3HT1 1 HUB TOP #1-16Ø 6061-T6 7 N
P1 P1
11 11 B 9281D3HB1 1 HUB BOTTOM #1-16Ø 6061-T6 7 N -
11 5 0
13 P1 12 B 9281D3HU2 16 HUB UNIVERSAL #2-16Ø 6061-T6 7 N -
P1 14 12 3 15
6 11
15 13 B 9281D3HU3 16 HUB UNIVERSAL #3-16Ø 6061-T6 7 N -
14 P1
1 12
P1 10 14 B 9281D3HU4 16 HUB UNIVERSAL #4-16Ø 6061-T6 7 N -
8 13 4 P1
13 6
P1 P1 15 B 9281D3HU5 16 HUB UNIVERSAL #5-16Ø 6061-T6 7 N -
3 2
12 6 9 15 -
P1
10
5 14 16 B 9281D3HU6 16 HUB UNIVERSAL #6-16Ø 6061-T6 7 N
15 2
7 9 17 B 9281D3HU7 16 HUB UNIVERSAL #7-16Ø 6061-T6 7 N -
11
P1 P1 14 P1 9
0 67C 7 4 5 18 B 9281D3HT8 8 HUB TOP #8-16Ø 6061-T6 7 N -
9 9 P5
P9 19 B 9281D3HB8 8 HUB BOTTOM #8-16Ø 6061-T6 7 N -
12 SL P8
10 13 -
5 8 7 6 15 20 B 9281D3HT9 8 HUB TOP #9-16Ø 6061-T6 7 N
8 -
15 P1
P8 7 21 B 9281D3HB9 8 HUB BOTTOM #9-16Ø 6061-T6 7 N
1 P6 6
13 P1 -
P1 7 P9 1 12 P1
22 B 9281D3HT10 8 HUB TOP #10-16Ø 6061-T6 7 N
5 9 8 0 8
P7 -
P7 23 B 9281D3HB10 8 HUB BOTTOM #10-16Ø 6061-T6 7 N
10 6
14
P5
8 9 24 B 9281D3HT11 8 HUB TOP #11-16Ø 6061-T6 7 N -
4 5 3
6 11 -
25 B 9281D3HB11 8 HUB BOTTOM #11-16Ø 6061-T6 7 N
5 5 15
P1 7 P1 26
4 3
15 P6 7 P5 5
14 4 27 B 9281D3P1 7 PANEL #1 3003-H16 37 N -
3 P2
P1 10 12
6 P6 P4 28 B 9281D3P1V 1 PANEL #1V, W/ VENT CUTOUT 3003-H16 34 N -
8 11
P9 P4 4 3 -
11 5 6 P1 29 B 9281D3P2 8 PANEL #2 3003-H16 50 N
13 5 4 2
7 9 30 B 9281D3P3 8 PANEL #3 3003-H16 49 N -
4 P8
P3 13
8 P2 3 31 B 9281D3P4 8 PANEL #4 3003-H16 50 N -
P2 3 15
P1 4 4 P1 32 B 9281D3P5 8 PANEL #5 3003-H16 51 N -
2 P3 7 6
15
71B 12 7 33 B 9281D3P6 8 PANEL #6 3003-H16 51 N -
9 P7 4 2
P7 14 -
7 2 70 3 34 B 9281D3P7 8 PANEL #7 3003-H16 51 N
2 5 10
P1 P8 -
3B 5 2 P4 8 P1
35 B 9281D3P8 8 PANEL #8 3003-H16 51 N
8 P3 4 -
11 4 10 36 B 9281D3P9 5 PANEL #9 3003-H16 45 N
P4 P1 P9
5 2 SL 14 -
P1 2 4 67A 37 B 9281D3P10 7 PANEL #10 3003-H16 43 N
71A 0 B 6 1 4 15
3 1 P1 P1 38 B 9281D4P10B 1 PANEL #10B, W/ PIPE CUTOUT 3003-H16 40 N -
P1 V 8 5
15 -
12 P1 3 1 P3 6 39 B 9281D3P11 7 PANEL #11 3003-H16 47 N
1M P5
2 2 13 40 B 9281D4P11M 1 PANEL #11M, W/ MANWAY CUTOUT 3003-H16 47 N -
9 P1 4 P6
P2
1 81 9 -
7
1 5 41 B 9281D3P12 8 PANEL #12 3003-H16 47 N
270° 9 5 P2 7 P1
90°
P6 1 1 42 B 9281D3P13 7 PANEL #13 3003-H16 43 N -
4 P1
13 2 9
69 68 2 P5 43 B 9281D4P13B 1 PANEL #13B, W/ PIPE CUTOUT 3003-H16 39 N -
6 P3 1 3 12
P1 15 44 B 9281D3P14 8 PANEL #14 3003-H16 43 N -
P1 8 3 P1
5 4 1 0 -
80 15
1 6 45 B 9281D3P15 8 PANEL #15 3003-H16 42 N
4 P1 2
14 P9 2 P1 P4 5 46 B 9281D3P16 8 PANEL #16 3003-H16 42 N -
10 4 11
P1 P4 P3 8 47
4 8 2 5 P8
10 5 2 48 B 9281D3S1 8 BEAM #1 6005A-T6/6061-T6 25 N -
P7 3 2 7 P1
14 P7 3 49 B 9281D3S2 8 BEAM #2 6005A-T6/6061-T6 19 N -
2 4 9
7 12 -
P3 15
50 B 9281D3S3 8 BEAM #3 6005A-T6/6061-T6 30 N
P1 7 4 P1
6 3 P2 4 2 51 B 9281D3S4 16 BEAM #4 6005A-T6/6061-T6 33 N -
15 P2
P3 3 8 -
13 P8 52 B 9281D3S5 16 BEAM #5 6005A-T6/6061-T6 21 N
4 7
9 4 5 13 53 B 9281D3S6 8 BEAM #6 6005A-T6/6061-T6 29 N -
P1 11
2 6 5 4 P4 P9
3 54 B 9281D3S7 16 BEAM #7 6005A-T6/6061-T6 34 N -
11 P4 8
P6
12 P2 P1
6 55 B 9281D3S8 16 BEAM #8 6005A-T6/6061-T6 30 N -
3 10
5 P5 P6 4 14 -
7 15
56 B 9281D3S9 16 BEAM #9 6005A-T6/6061-T6 21 N
P1 P1
3 5 7 4 -
15 5 57 B 9281D3S10 8 BEAM #10 6005A-T6/6061-T6 19 N
6 -
11 3 5 4 58 B 9281D3S11 8 BEAM #11 6005A-T6/6061-T6 33 N
9 8 P5 14
6 10 59 B 9281D3S12 16 BEAM #12 6005A-T6/6061-T6 32 N -
P7 P7
8 P1 P1 60 B 9281D3S13 16 BEAM #13 6005A-T6/6061-T6 27 N -
0 12 P1 P9 8 9
SL 7 5
1 6 P6 13 61 B 9281D3S14 16 BEAM #14 6005A-T6/6061-T6 28 N -
P8 P1
67B 7 1 15
8 62 B 9281D3S15 32 BEAM #15 6005A-T6/6061-T6 45 N -
15 6 8 5
10 7
13 P8 63
P9 12
P5
9 9 64 B 9281D3BATTENS 1 BATTEN EXTRUSION CUT SHEET 900 N -
P1 7
9 P1 P1
5 14 4 0 65
9 7 11
15 66 B 9281D4PRGA 1 PIER LAYOUT 468 N R
5 10 P1
15 14 9 6 2
12 P1 67 C 9281D3DSLASSY 3 DOME SKYLIGHT ASSEMBLY 121 N R
P1 3
2 68 B TCMWSQ24 1 24" SQ. MANWAY ASSY. 45 N R
P1 13 8
10 6 P1 13
P1 4 69 B TCMWSQ24RF 1 24" SQ. MANWAY REINFORCING FLG ALUM 5052-H32 8 N -
12 1 14
P1 15 70 B VAB24BAL 1 24" VENT ASSEMBLY W/ BIRD SCREEN 41 N R
15 11 12 14 6
P1 13
3 71 - SQ951BA-C 2 MAX CLOSED MASTER FLASH EPDM 15 N -
P1 P1 11
11 0 5
72 - 9281D3901 11 #8 TIN COATED GROUND CABLE W/ 1/4" EYELITS 18" LG N -
15
15
10 73
8
15 9 15 74 B 9281D3FL 32 FLASHING 3003-H16 19 N -
75 B 9281D3CF1A 32 COUNTER FLASHING #1A ALUM 3003 4 N -
76 B 9281D3CF1B 32 COUNTER FLASHING #1B ALUM 3003 4 N -
180°
77 - CFSPL006 64 .050" X 2" X 6" ALUM. ALUM 3003 N -
PLAN VIEW 78 - CFSPL051 32 .050" X 2" X 51" ALUM. ALUM 3003 N -
79
80 B 9281D4101 1 L3" X 3" X 3/8", SUPT. ANGLE ALUM 6061-T6 12 N -
81 B 9281D3102 1 L3" X 3" X 3/8", SUPT. ANGLE ALUM 6061-T6 15 N -
82 - SURFMNTHNGALNH 4 ALUM. SURFACE MOUNT HINGE (NO HOLES) ALUM 6061-T6 N -
83
70 84 - BLTHS05003750F593C 68 BOLT 1/2" X 3 3/4" F593C N -
85 - WSHLS0500188 68 WASHER 1/2" (LOCK) 18-8 N -
86 - NUTHS0500316 68 NUT 1/2" A316 N -
19'-3 3/8" [5877.7 mm] DOME HEIGHT

87 - BLTHS10MM40MMA270 4175 SS Bolt 10mm x 40mm [1 1/2"] A270 N -

88 - WSHLS10MMA2 4175 Washer 10mm (Lock) A2 N -
89 - NUTHS10MMA4 4175 Nut 10mm A4 N -
90 - BLTHS12MM40MMA270 1344 SS Bolt 12mm X 40mm [1 1/2"] A270 N -
91 - WSHLS12MMA2 1344 Washer 12mm (Lock) A2 N -
67B
92 - NUTHS12MMA4 1344 Nut 12mm A4 N -
68
93 - SCWTRI02500750188 4480 TRILOBE 1/4" X 3/4" W/ WASHER 18-8 N -
71B
94 - SCWTEK140750188 669 #14 TEK SCREW 3/4" W/ WASHER 18-8 N -
71A - -
* 95 SCWTEK141250188 1162 #14TEK SCREW 1 1/4" W/ WASHER 18-8 N
96 - SCWTRI02502500188 90 1/4" X 2 1/2" TRILOBE SCREW W/ WASHER 18-8 N -
97 - RIVDAL38198 404 DRIVE RIVET ALUMINUM N -
98 - RIVPALSL316250 303 POP RIVET ALUMINUM N -
99 - BLTHSM720MMA2 52 7mm Bolt X 20mm A2 N -
100 - WSHCS7MMA2 52 7mm WASHER A2 N -
101 - PEC890SAA20OZ 66 CAULKING / PECORA ULM SILICONE N -
* #14 X 1 1/2" TEK SCREW TO BE USED IN LIEU OF #14 X 1 1/4" AS NEEDED.
100'-0 13/16" [30500 mm] NOMINAL TANK I.D.

PLAN VIEW

ASSY. WT: 16780# PARENT: THE INFORMATION ON THIS DOCUMENT IS

CONFIDENTIAL PROPERTY OF TANK CUSTOMER NAME: TANK TECH ASIA PVT LTD CERTIFIED: APPROVED FOR CONSTRUCTION
TOLERANCES UNLESS OTHERWISE NOTED COLUMN TOLERANCES MANUFACTURER AND/OR ITS AFFILIATES. ANY
ANGULAR DEVIATION PERMISSIBLE DEVIATION NOMINAL LENGTH IN INCHES LINEAR TOLERANCE: OTHER USE, RETENTION, DISSEMINATION, ALUMINUM GEODESIC PROJ # 09281 JOB # D4
+0" / -1/8"
FORWARDING, PRINTING OR COPYING OF THIS PROJECT NAME: 7 DOMES FOR TTA ICO TENDER DOME FOR A Ø100'-0 13/16"
X = ±1.0° / X.X = ±0.5° 0 - 4" 4" - 48" 48" - 130" 130" - 240" 240"+ DOCUMENT TO UNAUTHORIZED PARTIES IS 3609 North 16th St . Parsons, Kansas 67357
STRICTLY PROHIBITED, WITHOUT THE 620.423.3010 . fax: 620.423.3999 STEEL TANK
LINEAR TOLERANCE: 1/32" 1/16" 1/8" 5/32" 3/16" SQUARENESS TOLERANCE: EXPRESSED WRITTEN CONSENT OF TANK
0 RELEASED FOR FABRICATION 10/28/2022 JLS MMP
DWG # 9281D4ASSEM
HOLE TO HOLE TOLERANCE: 1/32" ±3/32"
PROJECT LOCATION: CHENNAI, INDIA
1/32" 1/32" 1/16" 1/16" MANUFACTURER. REV REVISION DESCRIPTION DATE DRAWN BY CHECKED BY DWG SIZE: D SCALE: NTS
 PLACE 3 #14 x 1 1/4" TEK SCREWS EITHER SIDE OF SEAM IN
DOME FLASHING (TO BE INSTALLED
SUPPORT BLOCK. PREDRILL 3/16"Ø HOLES
CLOCKWISE TO ACHIEVE CORRECT LAP)
1/4" X 3/4" TRILOBE SCREW W/ WASHER
#14 X 1 1/4" SS TEK SCREWS
BATTEN
HUB COVER #14 X 3/4" SS TEK SCREWS TYPICALLY SPACED AT 8" BUT
USE AS REQ'D TO CLOSE ALL RETAINER & FLASHING GAPS TANK EAVE ANGLE
FIELD APPLY SEALANT TO CREATE WEATHERPROOF
SEAL BETWEEN FLASHING AND HUB COVER
BEND UNDER LAP TAB AND APPLY SEALANT AS REQ'D VENTED COUNTER FLASHING TO
NYLON FLASHING SHIM FOR WEATHER TIGHT SEAL AT ALL FLASHING JOINTS BE INSTALLED BETWEEN EAVE
ANGLE AND SPLICE PL
#14 X 1 1/4" SS TEK SCREWS FIELD CUT COUNTER FLASHING STRIP TO CORRECT LENGTH
AT PIER FLASHING SHIMS AND SEAL ANY GAPS BETWEEN COUNTER FLASHING JOINTS. FLASHING NOT DESIGNED AS A WALKING
USE SEALANT AND FASTEN WITH ALUMINUM RIVETS. SURFACE. LADDER PLATFORMS MUST EXTEND
#14 X 1 1/4" SS TEK SCREWS AT SEAM LOCATIONS OVER FLASHING.
PIER
SEALANT TO BE APPLIED AT FLASHING SEAM
DOME FLASHING
TIGHTEN AFTER ASSEMBLY DETAIL B

10°
FLASHING & COUNTER FLASHING INSTALLATION

COUNTER FLASHING PIER SHIM (NEOPRENE)

1/4" X 2 1/2"
SEALANT AROUND ENTIRE
TRILOBE SCREW
COUNTER FLASHING PL HUB COVER PERIMETER
W/ WASHER
#14 X 3/4" SS TEK SCREWS SPACED APPLY SEALANT BETWEEN WASHER AND HUB COVER
REF.

AROUND AT 8" OR AS REQ'D

1"

75 X 75 X 6
EAVE ANGLE HUB COVER
TOP HUB FIELD APPLY SEALANT ON COVER,
COUNTER FLASHING SPLICE:FIELD CUT COUNTER HUB, BATTEN AND PANEL GAPS
FLASHING STRIP TO CORRECT LENGTH AND SEAL DOME PANEL
ANY GAPS BETWEEN COUNTER FLASHING JOINTS.
USE SEALANT AND FASTEN WITH ALUM RIVETS.
DETAIL A
FLASHING INSTALLATION

BOTTOM HUB

DOME PANEL
DETAIL D
3/8" DRIVE RIVET THRU PANEL INTO HUB TYPICAL DOME BEAM CONNECTION 10mm SS BOLTS, WASHERS, & NUTS. EACH END
ALIGNMENT HOLE. TYP ALL 3 PANEL CORNERS OF BEAM FLANGE TO DOME HUB MIN OF 4 PLC'S
TOP & BOTTOM FLANGE

HUB COVER NOTES:

ALL MATERIAL IS MILL FINISH ALUMINUM UNLESS NOTED
DOME PANEL .050" ALUM PANEL CORNER MARKS ARE PANELS, FLASHING AND HUB COVERS 3003-H16 OR 5052-H32
FIELD APPLY SEALANT ON COVER, ORIENTATION MARK IS ON HUBS AND PLATES 6061-T6 OR 5052-H32
LABELED W/ "P" PANEL NUMBER
HUB, BATTEN AND PANEL GAPS THE RIGHT SIDE OF THE
1/4" X 3/4" TRILOBE AND "B" BEAM NUMBER OPPOSITE BEAM AND BATTEN STRIPS 6005A-T6 OR 6061-T6
SCREW W/ WASHER SIDE OF PANEL CORNER HOLE WHEN VIEWED
FROM THE TOP FASTENERS
BATTEN BAR W/ GASKET 10mm BOLTS, WASHERS, & NUTS
FLASHING OVERLAPS HUB P1 B1 12mm BOLTS, WASHERS, & NUTS
DOME STRUT (FIELD CUT AS NEEDED) PIER ANCHOR NOTES
1. ANCHOR POINT FOR EACH PIER HAVE TO MEET THE STRUCTURAL
1/4" X 2 1/2" TRILOBE SCREW W/ WASHER APPLY 12mm BOLTS, WASHERS, & NUTS REQUIREMENTS FOR ANCHORING.
SEALANT BETWEEN WASHER AND HUB COVER FASTENER TYP ALL HUB TO STRUT 2. ANCHORING POINT FOR EACH PIER MUST BE WITHIN +/- ½” OF THE DESIGNED
PIER CONNECTIONS RADIUS SHOWN ON THE APPROVAL AND INSTALLATION DRAWINGS.
TOP HUB
3. LEVELNESS TOLERANCE OF ANCHORING SURFACE MUST NOT EXCEED +/-⅛”
DETAIL C BETWEEN ADJACENT PIERS AND THE TOTAL DIFFERENCE FOR THE WHOLE
TYPICAL HUB, COVER & BATTEN INSTALLATION DOME FLASHING
DETAIL E ANCHORING SURFACE MUST BE LESS THAN +/-¼”.
PANEL LABELING 4. TANK WALL ROUNDNESS MUST BE WITHIN +/-1” OF THE DESIGNED RADIUS AS
SHOWN ON THE APPROVAL AND INSTALLATION DRAWINGS.
TOTAL WT: PARENT: THE INFORMATION ON THIS DOCUMENT IS
CONFIDENTIAL PROPERTY OF TANK
PRELIMINARY: NOT APPROVED FOR CONSTRUCTION
***DO NOT SCALE*** TOLERANCES UNLESS OTHERWISE NOTED MANUFACTURER AND/OR ITS AFFILIATES. ANY
DOME STANDARD
DRAWING IN INCHES ANGULAR DEVIATION PERMISSIBLE DEVIATION NOMINAL LENGTH IN INCHES OTHER USE, RETENTION, DISSEMINATION,
FORWARDING, PRINTING OR COPYING OF THIS INSTALLATION DETAILS PROJ # 09281 JOB # D1
ANSI/ASME Y14.1 STANDARDS
X = ±1.0° / X.X = ±0.5° 0 - 4" 4" - 48" 48" - 130" 130" - 240" 240"+ DOCUMENT TO UNAUTHORIZED PARTIES IS 3609 North 16th St . Parsons, Kansas 67357 1 RELEASE FOR FABRICATION 10/20/2022 MMP JLS ACCESSORIES
STRICTLY PROHIBITED, WITHOUT THE 620.423.3010 . fax: 620.423.3999
3RD ANGLE LINEAR TOLERANCE: 1/32" 1/16" 1/8" 5/32" 3/16" 0 NOT APPROVED FOR CONSTRUCTION 9/14/2022 MMP CW
EXPRESSED WRITTEN CONSENT OF TANK DWG # 9281D1A2
PROJECTION HOLE TO HOLE TOLERANCE: 1/32" 1/32" 1/32" 1/16" 1/16" MANUFACTURER. REV REVISION DESCRIPTION DATE DRAWN BY CHECKED BY DWG SIZE: B SCALE: NTS
 LOOP CABLE AND THIMBLE
8
(3) 3/8" 304SS THIMBLE AND CLIP KIT, THROUGH CENTER SUPPORT RING
INSTALL CLIPS MAX OF 5" APART DOME MANWAY

12 9
3/8" WIRE ROPE GRAB 304 SS PANEL #
INSTALL PER MFG. INSTRUCTIONS P12 3" X 3" X 3/8" ANGLE USE SEALANT
(SEE DETAIL 'B')
3/8"Ø S.S. HUB # ATTACH WITH 10mm
WIRE 5 SS BOLTS, WASHERS, & NUTS
9 9
DOME PANEL
STRUT & BATTEN #
DETAIL H
DOME MANWAY 30" SQ
LEGEND WITH REINFORCEMENT ANGLE

EXTEND ROPE TO ACCESS LADDER FIELD APPLY SEALANT BETWEEN CENTER

OR PLATFORM AND CUT TO SUPPORT BLOCK AND HUB COVER DOME PANEL
LENGTH, ATTACH TO PLATFORM 3" X 3" X 3/8" ALUM. REIN. ANGLE DOME VENT
DETAIL A DOME PANEL INSTALL ANGLE FLUSH WITH
CENTER SAFETY GRAB CABLE INSTALLATION DOME PANEL ATTACH WITH 10mm
SS BOLTS, WASHERS, & NUTS

DOME PANEL
10mm SS BOLTS, DOME PANEL
DOME ACCESSORY 3" X 3" X 3/8" ALUM WASHERS & NUTS
REINFORCING ANGLE 3" X 3" X 3/8" ANGLE USE SEALANT
D DRILL HOLES IN HINGE, (SEE DETAIL B)
FIELD CUT TO FIT BEAM ANGLE, AND BEAM AS NEEDED
BETWEEN DOME
STRUTS WITH DETAIL G
ALUM. HINGE
D MINIMUM CLEARANCE ALUMINUM DOME VENT
SECTION D-D WITH REINFORCEMENT ANGLE
(HEELS IN)
TYPICAL ALUM ANGLE
SUPT INSTALLATION

UTILIZE #SCWTRI02501000188
FOR ATACHMENT OF PIER ASSEMBLY
RUBBER MASTER #CFSPL006 ON BOTH SIDES OF
APPROXIMATE 1" GAP
IF ACCESSORY CUT EDGE IS FLASH BOOT PIER BASE (TO BE REMOVE UTILIZE 1/2" X 3 3/4"
BETWEEN DOME ACC.
WITHIN 18" OF STRUT, SECOND AFTER DOME IS INSTALLED) SS BOLTS,
AND SUPT. ANGLE
SUPT. ANGLE NOT REQ'D. #14 X 1 1/4" WASHERS, & NUTS
TEK SCREW FOR ATTACHMENT
GROUNDING
DETAIL B PIPING AND COMPONENTS CABLE TO BE PIER SHIM
TYPICAL ACCESSORY PENETRATION NOT TO BE SUPPORTED ATTACHED PIER BY
REINFORCEMENT ANGLE BY DOME SELF-TAPING
DOME PANEL SCREW, OTHER
FIELD CUT END ATTACHED BY
DOME SKYLIGHT BY CUSTOMER
(ASSEMBLED IN SHOP) DETAIL J
FLASHING BOOT DETAIL TYPICAL PIER ATTACHMENT DETAILS
EAVE ANGLE

SKYLIGHT SUPT. ANGLE

DETAIL A
DOME SKYLIGHT

TOTAL WT: PARENT: THE INFORMATION ON THIS DOCUMENT IS

CONFIDENTIAL PROPERTY OF TANK
PRELIMINARY: NOT APPROVED FOR CONSTRUCTION
***DO NOT SCALE*** TOLERANCES UNLESS OTHERWISE NOTED MANUFACTURER AND/OR ITS AFFILIATES. ANY
DOME STANDARD
DRAWING IN INCHES ANGULAR DEVIATION PERMISSIBLE DEVIATION NOMINAL LENGTH IN INCHES OTHER USE, RETENTION, DISSEMINATION,
FORWARDING, PRINTING OR COPYING OF THIS
2 RELEASE FOR FABRICATION 10/20/2022 MMP JLS
INSTALLATION DETAILS PROJ # 09281 JOB # D1
ANSI/ASME Y14.1 STANDARDS
X = ±1.0° / X.X = ±0.5° 0 - 4" 4" - 48" 48" - 130" 130" - 240" 240"+ DOCUMENT TO UNAUTHORIZED PARTIES IS 3609 North 16th St . Parsons, Kansas 67357 1 REVISED FOR RE-SUBMIT 9/27/2022 MMP CW ACCESSORIES
STRICTLY PROHIBITED, WITHOUT THE 620.423.3010 . fax: 620.423.3999
3RD ANGLE LINEAR TOLERANCE: 1/32" 1/16" 1/8" 5/32" 3/16" 0 NOT APPROVED FOR CONSTRUCTION 9/14/2022 MMP CW
EXPRESSED WRITTEN CONSENT OF TANK DWG # 9281D1A3
PROJECTION HOLE TO HOLE TOLERANCE: 1/32" 1/32" 1/32" 1/16" 1/16" MANUFACTURER. REV REVISION DESCRIPTION DATE DRAWN BY CHECKED BY DWG SIZE: B SCALE: NTS
 ITEM D/S PART NO. QTY DESCRIPTION MAT'L. GR. EST. WT. PAINT CODE
4 3 1 B CRSB06 1 CENTER RING SUPPORT BLOCK 2 X 2 X 7.875 LG. 6061 T6 4 - -
2 - 3046T75 1 LARGE OPENING HOIST RING 17-4 PH SS 5 - -
3 3 - WSHLS0750304 1 WASHER LOCK 3/4" 304SS 304SS - - -
4 - BLTHS07501500304 1 BOLT 3/4" X 1 1/2" HEX HD 304SS 304SS - - -
3

APPLY SEALANT BETWEEN

1
HUB COVER AND HOIST
RING BASE
FIELD DRILL
FOR 3/4" BOLT
HUB COVER

A A

TOP & BTM

HUBS

3
4
CENTER RING SAFETY TIE OFF SECTION A-A
POINT AT APEX 5000# MAX LOAD

6 UPDATED BORDER 10/22/2020 BLD JWC

TOTAL WT: 9 PARENT: --- THE INFORMATION ON THIS DOCUMENT IS
CONFIDENTIAL PROPERTY OF TANK
CERTIFIED: APPROVED FOR CONSTRUCTION
5 UPDATE BORDER 9/20/2020 PROG AUTO
***DO NOT SCALE*** TOLERANCES UNLESS OTHERWISE NOTED MANUFACTURER AND/OR ITS AFFILIATES. ANY
CENTER RING GENERAL
DRAWING IN INCHES ANGULAR DEVIATION PERMISSIBLE DEVIATION NOMINAL LENGTH IN INCHES OTHER USE, RETENTION, DISSEMINATION,
FORWARDING, PRINTING OR COPYING OF THIS
4 HARDWARE UPDATE 6/28/2016 MLH JLP
ARRANGEMENT FOR SAFETY TIE PROJ # --- JOB # ---
ANSI/ASME Y14.1 STANDARDS
X = ±1.0° / X.X = ±0.5° 0 - 4" 4" - 48" 48" - 130" 130" - 240" 240"+ DOCUMENT TO UNAUTHORIZED PARTIES IS 3609 North 16th St . Parsons, Kansas 67357 3 HARDWARE UPDATE 6/16/2016 MLH JLP OFF
STRICTLY PROHIBITED, WITHOUT THE 620.423.3010 . fax: 620.423.3999
3RD ANGLE LINEAR TOLERANCE: 1/32" 1/16" 1/8" 5/32" 3/16" 2 SWITHCED TO NEW BORDER 9/8/2014 BDS JLP
EXPRESSED WRITTEN CONSENT OF TANK DWG # CRGA06
PROJECTION HOLE TO HOLE TOLERANCE: 1/32" 1/32" 1/32" 1/16" 1/16" MANUFACTURER. REV REVISION DESCRIPTION DATE DRAWN BY CHECKED BY DWG SIZE: B SCALE: NTS
 ITEM D/S PART NUMBER QTY DESCRIPTION MAT'L. GR. EST. WT. PAINT CODE
1 B 9281D3PRASM 32 PIER ASSEMBLY 13 - R
2 B 9281D3PRSHIM 32 1/4" NEOPRENE SHIM NEOPRENE 1 - -
0° 3 B 9281D3CF3 32 COUNTER FLASHING #3 ALUM 3003 1 - -

A
0°
1'- 3/8" 9'-3 5/16"
n100'-6 13/16" O.D.
n100'-4 13/16" B.C.
n100'- 13/16" I.D. 6 3/8" 8'-9 3/8"
R50'-2 3/8" B.C.

9'-4 1/8" TYP.

CHO RD

10'-4 1/16" TYP

. C HO RD

DETAIL A

270° 90°
1

2
3

B B
1

2
ISOMETRIC VIEW B-B

EXISTING EAVE ANGLE

TANK INT.

SECTION B-B
TYP. (32) PLCS

180°
PLAN VIEW

TOTAL WT: 468 lbmass PARENT: THE INFORMATION ON THIS DOCUMENT IS

CONFIDENTIAL PROPERTY OF TANK
CERTIFIED: APPROVED FOR CONSTRUCTION
***DO NOT SCALE*** TOLERANCES UNLESS OTHERWISE NOTED MANUFACTURER AND/OR ITS AFFILIATES. ANY
DRAWING IN INCHES ANGULAR DEVIATION PERMISSIBLE DEVIATION NOMINAL LENGTH IN INCHES OTHER USE, RETENTION, DISSEMINATION,
FORWARDING, PRINTING OR COPYING OF THIS
PROJ # 09281 JOB # D4
ANSI/ASME Y14.1 STANDARDS PIER LAYOUT
X = ±1.0° / X.X = ±0.5° 0 - 4" 4" - 48" 48" - 130" 130" - 240" 240"+ DOCUMENT TO UNAUTHORIZED PARTIES IS 3609 North 16th St . Parsons, Kansas 67357
620.423.3010 . fax: 620.423.3999
STRICTLY PROHIBITED, WITHOUT THE
3RD ANGLE LINEAR TOLERANCE: 1/32" 1/16" 5/32" 1/8" 3/16" EXPRESSED WRITTEN CONSENT OF TANK
0 RELEASED FOR FABRICATION 10/28/2022 JLS MMP
DWG # 9281D4PRGA
PROJECTION HOLE TO HOLE TOLERANCE: 1/32" 1/32" 1/32" 1/16" 1/16" MANUFACTURER. REV DWG SIZE: B SCALE: NTS
 ITEM D/S PART NUMBER QTY DESCRIPTION MAT'L. GR. EST. WT. PAINT
1 B 9281D3PR1 1 PIER BASE (DIE #18518) X 7 3/8" LG. 6061-T6 6 -
2 B 9281D3PR2 2 PIER SHOE (DIE #18519) X 2 1/4in LG 6061-T6 -
3 - 9281D3PR3 1 PIER LINK (DIE #18517) X 2 1/4in LG 6061-T6 -
4 B 9281D3PR4 1 PIER BEAM I-6 X 19 15/16" LG. 6061-T6 6 -
5 B SHIMHDPE383A 1 .375 THK FLASHING SHIM NYLON 6/10 -
6 - 9281D3PR2_PTFETAPE 1 PTFE TAPE .020 THK X 3in X 2 1/4in LG - -
7 - 9281D3PR2_PTFETAPE2 2 PTFE TAPE .020 THK X 1in X 2 1/4in LG - -
8 - PTFETAP020315 1 PTFE TAPE .020 THK X 3" X 7 3/8" LG. - -
9 - PTFETAP0203415 2 PTFE TAPE .020 THK X 3/4" X 7 3/8" LG. - -
10 - BLTHS07502000F593D 1 BOLT 3/4" x 2" HEX HD F593D -
12 - NUTHS0750316 1 NUT 3/4" HEX HD A316 -
20 - WSHLS0750304 1 WASHER (LOCK) A304 -
21 - RIVPAL316750 2 RIVET POP DOME HD 3/16" DIA. (GRIP 5/8"-3/4") ALUM -

9
4 5

5 21
1
8

21 21

ISOMETRIC VIEW
ITEM #1 TAPE DETAIL
(OTHER COMPONENTS HIDDEN FOR CLARITY)

20 12 10

2 2

1 1 3
3
7 7

6
2 2
2 1/4" REF
ITEM #2 TAPE DETAIL
(OTHER COMPONENTS HIDDEN FOR CLARITY)
FRONT ASSEMBLY VIEW
SIDE ASSEMBLY VIEW

TOTAL WT: 13 lbmass PARENT: THE INFORMATION ON THIS DOCUMENT IS

CONFIDENTIAL PROPERTY OF TANK
CERTIFIED: APPROVED FOR CONSTRUCTION
***DO NOT SCALE*** TOLERANCES UNLESS OTHERWISE NOTED MANUFACTURER AND/OR ITS AFFILIATES. ANY
DRAWING IN INCHES
ANSI/ASME Y14.1 STANDARDS
ANGULAR DEVIATION PERMISSIBLE DEVIATION NOMINAL LENGTH IN INCHES
X = ±1.0° / X.X = ±0.5° 0 - 4" 4" - 48" 48" - 130" 130" - 240" 240"+
OTHER USE, RETENTION, DISSEMINATION,
FORWARDING, PRINTING OR COPYING OF THIS
DOCUMENT TO UNAUTHORIZED PARTIES IS
Connection PIER ASSEMBLY
PROJ # 09281 JOB # D3
STRICTLY PROHIBITED, WITHOUT THE AFFILIATE GROUP
3RD ANGLE LINEAR TOLERANCE: 1/32" 1/16" 5/32" 1/8" 3/16" 3609 North 16th St . Parsons, Kansas 67357 0 RELEASED FOR FABRICATION 10/27/2022 JLS MMP
EXPRESSED WRITTEN CONSENT OF TANK 620.423.3010 . fax: 620.423.3999 DWG # 9281D3PRASM
PROJECTION HOLE TO HOLE TOLERANCE: 1/32" 1/32" 1/32" 1/16" 1/16" MANUFACTURER. REV REVISION DESCRIPTION DATE DRAWN BY CHECKED BY DWG SIZE: B SCALE: NTS
 ITEM D/S PART NUMBER QTY DESCRIPTION MAT'L. GR. EST. WT. PAINT CODE
H4 1 B 9281D3SLEXT1 1 DOME SKYLIGHT EXTRUSION X 91 11/16" LG 6005-AT61 4 N -
H4
HUB IDENTIFICATION 2 B 9281D3SLEXT2 1 DOME SKYLIGHT EXTRUSION X 12'-9 3/8" LG 6005-AT61 7 N -
MARK 3 B 9281D3SLEXT3 1 DOME SKYLIGHT EXTRUSION X 12'-9 3/8" LG 6005-AT61 7 N -
4 B 9281D3SLGL 1 DOME SKYLIGHT GLASS, 1/4" ACRYLIC Plexiglass 13 N -
5 B 9281D3SLP1 1 DOME SKYLIGHT END CAP ALUM 3003 N -
6 B 9281D3SLP2 1 DOME SKYLIGHT END CAP ALUM 3003 N -
7 B 9281D3SLP3 1 DOME SKYLIGHT END CAP ALUM 3003 N -
8 B 9281D3ANG1 1 DOME SKYLIGHT SUPT, L3" X 3" X 3/8" X 79 15/16" LG ALUM 6061-T6 15 N -
9 B 9281D3ANG2 1 DOME SKYLIGHT SUPT, L3" X 3" X 3/8" X 79 15/16" LG ALUM 6061-T6 15 N -
10 B 9281D3ANG3 1 DOME SKYLIGHT SUPT, L3" X 3" X 3/8" X 51 3/4" LG ALUM 6061-T6 10 N -
11 B 9281D3SLCLP1 1 SUPT. CLIP ALUM 5052-H32 1 N -
12 B 9281D3SLCLP2 1 SUPT. CLIP ALUM 5052-H32 1 N -
13 B 9281D3SLCLP3 1 SUPT. CLIP ALUM 5052-H32 1 N -
APPLY SEALANT 14 C 9281D3SLRA 1 SKYLIGHT RETAINING FLANGE ASSY. 45 N -
14
BETWEEN SKYLIGHT - -
15 SCWTEK121000316 91 TEK SCREW #12 X 1" SS HEX HEAD A316 N
& RETAINING ANGLE FRAME
10 16 - WSHCS12316 91 #12 SEALING NEOPRENE WASHER A316 N -
* 17 - 86573MVHBTAPE 1 3M VHB TAPE DOUBLE SIDED - 2" WIDE X 58 LINEAR FT - N -
A - - -
18 PEC890SAA20OZ 6 PECORA 890 SILICONE SEALANT 20oz SG TUBE ALUM N
A
17

NOTE: ASSEMBLED IN SHOP

* APPLY DBL SIDED TAPE TO TOP OF SUPPORT ANGLE UNDER GLASS.

14

B
B

HUB IDENTIFICATION HUB IDENTIFICATION

MARK MARK
H2
H2

H2
H2

TOP ASSY. VIEW

3
2 C
14

ISOMETRIC VIEW
4

APPLY SEALANT 2

4 14
OUTSIDE ISOMETRIC VIEW A
10
8"

12' -

15 16
9 1/

14
9 1/
12' -

16 15
8"

13 10 12 4 12 2

2
SECTION A-A
4 14
1 TYP (4) PLCS
15 16 -@ CLIP TO EXT.
5 CONNECTION
9
8
DETAIL C 2
10
SIMILAR (3) PLCS
HLS ARE PRE-DRILLED
16 15
FOR ALIGN PURPOSES
4

INSIDE ISOMETRIC VIEW A

5/16" TYP
GAP

11

7 5 2 ISOMETRIC VIEW B
1
91 1/2"
16 15 CAULK
TOP (2) SCREWS TO BE 14
TOP ASSY. VIEW 15 16 -INSTALLED THROUGH
TOP SUPPORTS NOT SHOWN FOR CLARITY ITEM #14 COVER 4

1 2
5

DETAIL C SECTION B-B

FRONT ASSY. VIEW ITEM 14 HIDDEN FOR CLARITY

TOTAL WT: 121 lbmass PARENT: THE INFORMATION ON THIS DOCUMENT IS

CONFIDENTIAL PROPERTY OF TANK
CERTIFIED: APPROVED FOR CONSTRUCTION
***DO NOT SCALE*** TOLERANCES UNLESS OTHERWISE NOTED MANUFACTURER AND/OR ITS AFFILIATES. ANY
DRAWING IN INCHES
ANSI/ASME Y14.1 STANDARDS
ANGULAR DEVIATION PERMISSIBLE DEVIATION NOMINAL LENGTH IN INCHES
X = ±1.0° / X.X = ±0.5° 0 - 4" 4" - 48" 48" - 130" 130" - 240" 240"+
OTHER USE, RETENTION, DISSEMINATION,
FORWARDING, PRINTING OR COPYING OF THIS
DOCUMENT TO UNAUTHORIZED PARTIES IS
Connection DOME SKYLIGHT ASSEMBLY
PROJ # 09281 JOB # D3
STRICTLY PROHIBITED, WITHOUT THE AFFILIATE GROUP
3RD ANGLE LINEAR TOLERANCE: 1/32" 1/16" 5/32" 1/8" 3/16" 3609 North 16th St . Parsons, Kansas 67357 0 RELEASED FOR FABRICATION 10/27/2022 JLS MMP
EXPRESSED WRITTEN CONSENT OF TANK 620.423.3010 . fax: 620.423.3999 DWG # 9281D3DSLASSY
PROJECTION HOLE TO HOLE TOLERANCE: 1/32" 1/32" 1/32" 1/16" 1/16" MANUFACTURER. REV REVISION DESCRIPTION DATE DRAWN BY CHECKED BY DWG SIZE: C SCALE: NTS
 ITEM D/S PART NUMBER QTY DESCRIPTION MAT'L. GR. EST. WT. PAINT CODE
1 B TCMW24BASE 1 24" SQ. DOME MANWAY BASE 14 N -
2 B TCMW24COVER 1 24" SQ DOME MANWAY COVER 21 N -
3 - TCMW24SEAL 10 (MC - 1120A312) WR RUBBER PUSH-ON SEAL LINEAR FT. 1 N -
4 - BLTHS03751500304 3 BOLT 3/8" X 1 1/2" LG HEX HD SS A304 N -
5 - WSHLS0375304 3 WASHER LOCK 3/8" SS A304 N -
6 - NUTHS0375316 5 NUT 3/8" HEX A316 N -

31" O.S. SQ.

(6) SPCS @ 4" = 24" TYP

1 1/4" 1 1/4"
TYP TYP

5 4 6
DBL NUT LOOSE FIT
CONNECTION
TYP (2) PLCS
24" SQ. OPENING

5 4 6

A A
ISOMETRIC VIEW

(28) n7/16" HLS

TOP ASSY. VIEW

2
3

4 5/8"
4 6

24" SQ. OPENING

1
1
FRONT ASSY. VIEW

SECTION A-A

TOTAL WT: 45 lbmass PARENT: THE INFORMATION ON THIS DOCUMENT IS

CONFIDENTIAL PROPERTY OF TANK
CERTIFIED: APPROVED FOR CONSTRUCTION
***DO NOT SCALE*** TOLERANCES UNLESS OTHERWISE NOTED MANUFACTURER AND/OR ITS AFFILIATES. ANY
DRAWING IN INCHES ANGULAR DEVIATION PERMISSIBLE DEVIATION NOMINAL LENGTH IN INCHES OTHER USE, RETENTION, DISSEMINATION,
PROJ # - JOB # -
FORWARDING, PRINTING OR COPYING OF THIS
ANSI/ASME Y14.1 STANDARDS 24" SQ. MANWAY ASSY.
X = ±1.0° / X.X = ±0.5° 0 - 4" 4" - 48" 48" - 130" 130" - 240" 240"+ DOCUMENT TO UNAUTHORIZED PARTIES IS 3609 North 16th St . Parsons, Kansas 67357
620.423.3010 . fax: 620.423.3999
STRICTLY PROHIBITED, WITHOUT THE
3RD ANGLE LINEAR TOLERANCE: 1/32" 1/16" 5/32" 1/8" 3/16" EXPRESSED WRITTEN CONSENT OF TANK
0 RELEASED FOR FABRICATION 7/1/2022 JLS MMP
DWG # TCMWSQ24
PROJECTION HOLE TO HOLE TOLERANCE: 1/32" 1/32" 1/32" 1/16" 1/16" MANUFACTURER. REV DWG SIZE: B SCALE: NTS
 ITEM D/S PART NO. QTY DESCRIPTION MAT'L. GR. EST. WT. PAINT CODE
1 B VNB24AL 1 24" VENT NECK W/ FLANGED BOTTOM ALUM 15 - -
2 B VCA24AB 1 24" ALUM. VENT CAP ASSEMBLY W/ BIRD SCREEN ALUM 26 - -
3 B GSKT24VAI 1 GASKET FOR 24" VENT ASSEMBLY EPDM - - -
2 1 4 - BLTHS05002250304 3 BOLT 1/2" X 2 1/4" HEX HD (304SS) A304 - - -
2 1 5 - WSHFS0500304 5 WASHER FLAT 1/2" (304SS) A304 - - -
2 1 6 - NUTHS0500316 5 NUT 1/2" HEX HD (316SS) A316 - - -

5 4

5 6 6

SECTION A-A
DOUBLE NUT (1)
SIDE FOR HINGE
BIRD SCREEN

A A

SEE A3 FOR ATTACHMENT DETAILS

DOME PANEL AND CONNECTION HARDWARE

5 CHANGE HARDWARE CALLOUT 9/27/2022 MMP JWC

TOTAL WT: 41 PARENT: --- THE INFORMATION ON THIS DOCUMENT IS
CONFIDENTIAL PROPERTY OF TANK
CERTIFIED: APPROVED FOR CONSTRUCTION
4 FIXED REVS. 5/24/2021 BLD JWC
***DO NOT SCALE*** TOLERANCES UNLESS OTHERWISE NOTED MANUFACTURER AND/OR ITS AFFILIATES. ANY
24" VENT ASSEMBLY W/ BIRD
DRAWING IN INCHES ANGULAR DEVIATION PERMISSIBLE DEVIATION NOMINAL LENGTH IN INCHES OTHER USE, RETENTION, DISSEMINATION,
FORWARDING, PRINTING OR COPYING OF THIS
3 UPDATE BORDER 9/21/2020 PROG AUTO
SCREEN PROJ # --- JOB # ---
ANSI/ASME Y14.1 STANDARDS
X = ±1.0° / X.X = ±0.5° 0 - 4" 4" - 48" 48" - 130" 130" - 240" 240"+ DOCUMENT TO UNAUTHORIZED PARTIES IS 3609 North 16th St . Parsons, Kansas 67357 2 REVISED HARDWARE 2/22/2018 MLH JWC
STRICTLY PROHIBITED, WITHOUT THE 620.423.3010 . fax: 620.423.3999
3RD ANGLE LINEAR TOLERANCE: 1/32" 1/16" 1/8" 5/32" 3/16" 1 HARDWARE UPDATE 8/30/2016 MLH JLP
EXPRESSED WRITTEN CONSENT OF TANK DWG # VAB24BAL
PROJECTION HOLE TO HOLE TOLERANCE: 1/32" 1/32" 1/32" 1/16" 1/16" MANUFACTURER. REV REVISION DESCRIPTION DATE DRAWN BY CHECKED BY DWG SIZE: B SCALE: NTS