Srge Piping Specification For Topsides: Technical Specification I-ET-3010.2D-1200-200-P4X-001

Nº:
TECHNICAL SPECIFICATION I-ET-3010.2D-1200-200-P4X-001

CLIENT: SHEET:
AGUP 1 of 18
JOB:
HIGH CAPACITY FPSO - GAS EXPORTATION ALL ELECTRIC
AREA:
ATAPU 2 AND SÉPIA 2
TITLE:
INTERNAL
SRGE PIPING SPECIFICATION FOR TOPSIDES
ESUP
INDEX OF REVISIONS
REV. DESCRIPTION AND/OR REVISED SHEETS

0 ORIGINAL ISSUE
A GENERAL REVISION
REV. 0 REV. A REV. B REV. C REV. D REV. E REV. F REV. G REV. H

DATE MAY/27/22 DEC/16/22
DESIGN EEA EEA
EXECUTION UPTP UPTP
CHECK U4T1 CXDI
APPROVAL U32N U32N
INFORMATION IN THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING PROHIBITED OUTSIDE OF THEIR PURPOSE
FORM OWNED TO PETROBRAS N-0381 REV. L
INTERNA \ Qualquer Usuário

REV.
TECHNICAL SPECIFICATION Nº I-ET-3010.2D-1200-200-P4X-001 A
AREA: SHEET
ATAPU 2 AND SÉPIA 2 2 of 19
TITLE:
INTERNAL
PIPING SPECIFICATION FOR TOPSIDES
ESUP
SUMMARY
1 SCOPE ...................................................................................................................... 3
2 NORMATIVE REFERENCES .................................................................................... 3
3 SYMBOLS AND ABBREVIATED TERMS .............................................................. 10
4 PIPING TAGGING SYSTEM ................................................................................... 12
5 PIPING SPECIFICATIONS X SERVICES ............................................................... 14
6 PIPING SPECIFICATIONS ...................................................................................... 16
7 PIPING SPECIFICATION CODE RULE .................................................................. 18
8 PIPING MATERIAL SPECIFICATIONS .................................................................. 19
ANNEX
A. Valves and Valve Datasheets

B. Pipes, Fittings and Accessories and Datasheets
C. Typical Arrangement for Drain&Vent and Instruments
D. Piping Material Selection for Corrosive HC and Produced Water
E. Flange Isolation Kit
F. Requirements for Piping internal Coating (cancelled)
G. Welding Requirements
H. Requirements for FRP Pipes and Fittings
J. Piping Weld Inspection (cancelled)
K. Pressure Safety Valves and PSV Datasheets

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
1 SCOPE
This Guideline standardizes piping and valves materials for use in oil and gas exploration and
production facilities.
This document specifies requirements for acquisition of: pipes, valves, fittings, flanges, gaskets
bolts and nuts. Aspects of design, performance, materials, fabrication, testing, inspection, marking,
storage, expedition and documentation are covered.
The designer is responsable for selecting the piping material specification (spec) taking into
account its limitations, such as: service, pressure and temperature.
2 NORMATIVE REFERENCES
Note: The Standards referred herein shall be considered in their latest edition/revision.
API RP 14E Recommended Practice for Design and Installation of offshore Production
Platform Piping Systems.
API SPEC 5L Specification for Line Pipe.
API 6A Specification for Wellhead and Christmas Tree Equipment
API SPEC 6D Petroleum and Natural Gas Industries – Pipeline Transportation Systems -
Pipeline Valves.
API STD 526 Flanged Steel Pressure-relief Valves
API STD 594 Check Valves: Wafer, Wafer - Lug, and Double Flanged Type.
API STD 598 Valve Inspection and Testing
API STD 599 Metal Plug Valves - Flanged, Threaded and Welding Ends
API STD 600 Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas Industries.
API STD 602 ISO 15671 – Compact Steel Gate Valves – Flanged, Threaded, Welding, and
Extended – Body Ends.
API STD 607 Fire Test for Quarter turn Valves and Valves Equipped with Nonmetallic Seats
API STD 609 Butterfly Valves: Double Flanged, Lug and Wafer – Type.
ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form).
ASME B1.20.1 Pipe Threads, General Purpose (Inch).
ASME B16.1 Cast Iron Pipe Flanges and Flanged Fittings Classes 25, 125 and 250.
ASME B16.5 Pipe flanges and flanged fittings NPS 1/2 through NPS 24 metric/inch
standard revision e ASME B16.5
ASME B16.9 Factory-made wrought steel buttwelding fittings.
ASME B16.10 Face-to-face and end-to-end to valves
ASME B16.11 Forged Fittings, Socket-Welding and Threaded.
ASME B16.20 Metallic gaskets for pipe flanges ring-joint, spiral-wound, and jacketed.
ASME B16.21 Nonmetallic Flat Gaskets for Pipe Flanges.
ASME B16.25 Buttwelding Ends.
ASME B16.28 Wrought Steel Buttwelding Short Radius Elbows and Returns.
ASME B16.34 Valves – Flanged, threaded and welding end
ASME B16.47 Large diameter Steel Flanges (NPS 26 through NPS 60).
ASME B16.5 Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch
Standard
ASME B18.2.2 Square and Hex Nuts (Inch Series).

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
ASME B31.3 Process Piping.

ASME B31.4 Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids
ASME B31.8 Gas Transmission and Distribution Piping Systems
ASME B36.10 Welded and Seamless Wrought Steel Pipe.
ASME B36.19 Stainless Steel Pipe
ASTM A105 Standard Specification for Aço carbonoForgings for Piping Applications.
ASTM A106 Standard Specification for Seamless Aço carbonoPipe for High Temperature
Service.
ASTM A123 Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and
Steel Products.
ASTM A126 Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe
Fittings.
ASTM A182 Standard Specification for Forged or Rolled Alloy Steel Pipe Flanges, Forged
Fittings, and Valves and Parts for High Temperature Service.
ASTM A193 Standard Specification for Alloy Steel and Stainless Steel Bolting Materials for
High Temperature Service.
ASTM A194 Standard specification for carbon and alloy steel nuts for bolts for high
pressure or high temperature service, or both.
ASTM A216 Standard Specification for Steel Castings, Carbon, Suitable for Fusion
Welding, High Temperature Service.
ASTM A234 Standard Specification for Piping Fittings of Wrought Aço carbonoand Alloy
Steel for Moderate and High Temperature Service.
ASTM A269 Standard Specification for Seamless and Welded Austenitic Stainless Steel
Tubing for General Service
ASTM A312 Standard Specification for Seamless, Welded, and Heavily Cold Worked
Austenitic Stainless Steel Pipes.
ASTM A320 Standard Specification for Alloy Steel and Stainless Steel Bolting Materials
Low High Temperature Service.
ASTM A333 Standard Specification for Seamless and Welded Steel Pipe for Low
Temperature Service.
ASTM A350 Standard Specification for Carbon and Low Alloy Steel Forgings, Requiring
Notch Toughness Testing for Piping Components.
ASTM A351 Standard Specification for Castings, Austenitic, Austenitic Ferritic (Duplex), for
Pressure Containing Parts.
ASTM A352 Standard Specification for Steel Castings, Ferritic and Martensitic, for
Pressure Containing Parts, Suitable for Low Temperature Service.
ASTM A358 Standard Specification for Electric Fusion Welded Austenitic Chromium Nickel
Stainless Steel Pipe for High Temperature Service and General Applications
ASTM A403 Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings.
ASTM A420 Standard Specification for Piping Fittings of Wrought Aço carbonoand Alloy
Steel for Low Temperature Service.
ASTM A487 Standard Specification for Steel Castings Suitable for Pressure Service.
ASTM A522 Standard Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel
Flanges, Fittings, Valves, and Parts for Low Temperature Service
ASTM A536 Standard Specification for Ductile Iron Castings.
ASTM A564 Standard Specification for Hot Rolled and Cold Finished Age Hardening
Stainless Steel Bars and Shapes.
ASTM A671 Standard Specification for Eletric Fusion Welded Steel Pipe for Atmospheric
and Lower Temperatures.
ASTM A694 Standard Specification for Carbon and Alloy Steel Forgings for Pipe Flanges,
Fittings, Valves, and Parts for High Pressure Transmission Service.

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
ASTM A733 Standard Specification for Welded and Seamless Carbon Steel and Austenitic
Stainless Steel Pipe Nipples
ASTM A790 Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless
Steel Pipe.
ASTM A815 Standard Specification for Wrought Ferritic, Ferritic/Austenitic, and Martensitic
Stainless Steel Piping Fittings.
ASTM A928 Standard Specification for Ferritic/Austenitic (Duplex) Stainless Steel Pipe
Electric Fusion Welded with Addition of Filler Metal
ASTM A995 Standard Specification for Castings, Austenitic Ferritic (Duplex) Stainless
Steel, for Pressure Containing Parts
ASTM B62 Standard Specification for Composition Bronze or Ounce Metal Castings.
ASTM B366 Standard Specification for Factory Made Wrought Nickel and Nickel Alloy
Fittings
ASTM B444 Specification for Nickel Chromium Molybdenum Columbium Alloys (UNS
N06625 and UNS N06852) and Nickel Chromium Molybdenum Silicon Alloy
(UNS N06219) Pipe and Tube
ASTM B564 Specification for Nickel Alloy Forgings
ASTM B584 Standard Specification for Copper Alloy Sand Castings for General
Applications.
ASTM D1784 Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Compounds and
Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds.
ASTM D1785 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules
40, 80 and 120.
ASTM D2467 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings,
Schedule 80.
ASTM D3567 Standard Practice for Determining Dimensions of Fiberglass (Glass-Fiber
Reinforced Thermosetting Resin) Pipe and Fittings R (2002).
ASTM D4024 Standard Specification for Machine Made "Fiberglass" (Glass-Fiber Reinforced
Thermosetting Resin) Flanges (2000).
ASTM F1173 Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to be
used for Marine Applications (2001).
ASTM F1387 Standard Specification for Performance of Piping and Tubing Mechanically
Attached Fittings
ASTM F439 Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic
Pipe Fittings, Schedule 80.
BSI BS 1873 Stell Globe and Globe Stop and Check Valves (flanged and butt welding ends)
for the Petroleum, Petrochemical and Allied Industries.
BSI BS 3799 Steel Pipe Fittings, Screwed and Socket Welding for the Petroleum Industry.
BSI BS 5152 Cast Iron Globe and Globe Stop and Check Valves for General Purposes.
BSI BS 5351 Steel Ball Valves for the Petroleum, Petrochemical and Allied Industries.
BSI BS 5352 Steel Wedge Gate, Globe and Check Valves 50 mm and Smaller for the
Petroleum, Petrochemical and Allied Industries.
EEMUA 144 90/10 Copper Nickel Alloy Piping for Offshore Applications. Tubes Seamless
and Welded.
EEMUA 145 90/10 Copper Nickel Alloy Piping for Offshore Applications. Flanges
Composite and Solid.
EEMUA 146 90/10 Copper Nickel Alloy Piping for Offshore Applications. Fittings.
IMO A 753(18) International Maritime Organization Resolution A 753(18).
IOGP S-562 Supplementary Requirements to API Specification 6D Ball Valves
IOGP S-563 Material Data Sheets for Piping and Valve Components

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
IOGP S-611 Supplementary Requirements to API 600 Steel Gate Valves and to API 603
CRA Gate Valves
ISO 15156 Petroleum and natural gas industries: Materials for use in H2S containing
environments in oil and gas production.
ISO 14692 Petroleum and natural gas industries: Glass reinforced plastic (GRP) piping.
ISO 17292 Metal ball valves for petroleum, petrochemical and allied industries.
ISO 21457 Petroleum, petrochemical and natural gas industries – Material selection and
corrosion control for oil and gas production systems.
ISO 27509 Petroleum and natural gas industries: Compact Flanged connections with IX
seal ring (First Edition).
MSS SP 6 Standard Finishes for Contact Faces de Pipe Flanges and Connecting End
Flanges of Valves and Fittings.
MSS SP70 Cast Iron Gate Valves, Flanged and Threaded Ends.
MSS SP 71 Gray Iron Swing Check Valves, Flanged and Threaded Ends.
MSS SP 72 Ball Valves with Flanged or Butt Welding Ends for General Service.
MSS SP 75 Strength, Wrought, Butt Welding Fittings.
MSS SP 80 Bronze Gate, Globe, Angle and Check Valves.
MSS SP 83 Steel Pipe Unions, Socket Welding and Threaded.
MSS SP 88 Diaphragm Type Valves.
MSS SP 95 Swage (d) Nipples and Bull Plugs.
MSS SP 97 Integrally Reinforced Forged Branch Outlet Fittings – Socket Welding,
Threaded, and Buttwelding Ends.
NBR 15827 Industrial Valves for Installations of Exploration, Production, Refining and
Transport of Petroleum Products - Requirements for Design and Prototype
Test.
NORSOK M-001 Materials Selection
API RP 14E Recommended Practice for Design and Installation of offshore

Production Platform Piping Systems.
API SPEC 5L Specification for Line Pipe.
API 6A Specification for Wellhead and Christmas Tree Equipment
API SPEC 6D Petroleum and Natural Gas Industries – Pipeline Transportation Systems
- Pipeline Valves.
API STD 526 Flanged Steel Pressure-relief Valves
API STD 594 Check Valves: Wafer, Wafer - Lug, and Double Flanged Type.
API STD 598 Valve Inspection and Testing
API STD 599 Metal Plug Valves - Flanged, Threaded and Welding Ends
API STD 600 Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas
Industries.
API STD 602 ISO 15671 – Compact Steel Gate Valves – Flanged, Threaded, Welding,
and Extended – Body Ends.
API STD 607 Fire Test for Quarter turn Valves and Valves Equipped with Nonmetallic
Seats
API STD 609 Butterfly Valves: Double Flanged, Lug and Wafer – Type.
ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form).
ASME B1.20.1 Pipe Threads, General Purpose (Inch).

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
ASME B16.1 Cast Iron Pipe Flanges and Flanged Fittings Classes 25, 125 and 250.
ASME B16.5 Pipe flanges and flanged fittings NPS 1/2 through NPS 24 metric/inch
standard revision e ASME B16.5
ASME B16.9 Factory-made wrought steel buttwelding fittings.
ASME B16.10 Face-to-face and end-to-end to valves
ASME B16.11 Forged Fittings, Socket-Welding and Threaded.
ASME B16.20 Metallic gaskets for pipe flanges ring-joint, spiral-wound, and jacketed.
ASME B16.21 Nonmetallic Flat Gaskets for Pipe Flanges.
ASME B16.25 Buttwelding Ends.
ASME B16.28 Wrought Steel Buttwelding Short Radius Elbows and Returns.
ASME B16.34 Valves – Flanged, threaded and welding end
ASME B16.47 Large diameter Steel Flanges (NPS 26 through NPS 60).
ASME B16.5 Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch
Standard
ASME B18.2.2 Square and Hex Nuts (Inch Series).
ASME B31.3 Process Piping.
ASME B31.4 Pipeline Transportation Systems for Liquid Hydrocarbons and Other
Liquids
ASME B31.8 Gas Transmission and Distribution Piping Systems
ASME B36.10 Welded and Seamless Wrought Steel Pipe.
ASME B36.19 Stainless Steel Pipe
ASTM A105 Standard Specification for Aço carbonoForgings for Piping Applications.
ASTM A106 Standard Specification for Seamless Aço carbonoPipe for High
ASTM A123 Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron
and Steel Products.
ASTM A126 Standard Specification for Gray Iron Castings for Valves, Flanges, and
Pipe Fittings.
ASTM A182 Standard Specification for Forged or Rolled Alloy Steel Pipe Flanges,
Forged Fittings, and Valves and Parts for High Temperature Service.
ASTM A193 Standard Specification for Alloy Steel and Stainless Steel Bolting
Materials for High Temperature Service.
ASTM A194 Standard specification for carbon and alloy steel nuts for bolts for high
pressure or high temperature service, or both.
ASTM A216 Standard Specification for Steel Castings, Carbon, Suitable for Fusion
Welding, High Temperature Service.
ASTM A234 Standard Specification for Piping Fittings of Wrought Aço carbonoand
Alloy Steel for Moderate and High Temperature Service.
ASTM A269 Standard Specification for Seamless and Welded Austenitic Stainless
Steel Tubing for General Service
ASTM A312 Standard Specification for Seamless, Welded, and Heavily Cold Worked
Austenitic Stainless Steel Pipes.
ASTM A320 Standard Specification for Alloy Steel and Stainless Steel Bolting
Materials Low High Temperature Service.
ASTM A333 Standard Specification for Seamless and Welded Steel Pipe for Low

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
ASTM A350 Standard Specification for Carbon and Low Alloy Steel Forgings,
Requiring Notch Toughness Testing for Piping Components.
ASTM A351 Standard Specification for Castings, Austenitic, Austenitic Ferritic
(Duplex), for Pressure Containing Parts.
ASTM A352 Standard Specification for Steel Castings, Ferritic and Martensitic, for
Pressure Containing Parts, Suitable for Low Temperature Service.
ASTM A358 Standard Specification for Electric Fusion Welded Austenitic Chromium
Nickel Stainless Steel Pipe for High Temperature Service and General
Applications
ASTM A403 Standard Specification for Wrought Austenitic Stainless Steel Piping
Fittings.
ASTM A420 Standard Specification for Piping Fittings of Wrought Aço carbonoand
Alloy Steel for Low Temperature Service.
ASTM A487 Standard Specification for Steel Castings Suitable for Pressure Service.
ASTM A522 Standard Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel
Flanges, Fittings, Valves, and Parts for Low Temperature Service
ASTM A536 Standard Specification for Ductile Iron Castings.
ASTM A564 Standard Specification for Hot Rolled and Cold Finished Age Hardening
Stainless Steel Bars and Shapes.
ASTM A671 Standard Specification for Eletric Fusion Welded Steel Pipe for
Atmospheric and Lower Temperatures.
ASTM A694 Standard Specification for Carbon and Alloy Steel Forgings for Pipe
Flanges, Fittings, Valves, and Parts for High Pressure Transmission
Service.
ASTM A733 Standard Specification for Welded and Seamless Carbon Steel and
Austenitic Stainless Steel Pipe Nipples
ASTM A790 Standard Specification for Seamless and Welded Ferritic/Austenitic
Stainless Steel Pipe.
ASTM A815 Standard Specification for Wrought Ferritic, Ferritic/Austenitic, and
Martensitic Stainless Steel Piping Fittings.
ASTM A928 Standard Specification for Ferritic/Austenitic (Duplex) Stainless Steel
Pipe Electric Fusion Welded with Addition of Filler Metal
ASTM A995 Standard Specification for Castings, Austenitic Ferritic (Duplex)
Stainless Steel, for Pressure Containing Parts
ASTM B62 Standard Specification for Composition Bronze or Ounce Metal Castings.
ASTM B366 Standard Specification for Factory Made Wrought Nickel and Nickel
Alloy Fittings
ASTM B444 Specification for Nickel Chromium Molybdenum Columbium Alloys
(UNS N06625 and UNS N06852) and Nickel Chromium Molybdenum
Silicon Alloy (UNS N06219) Pipe and Tube
ASTM B564 Specification for Nickel Alloy Forgings
ASTM B584 Standard Specification for Copper Alloy Sand Castings for General
Applications.
ASTM D1784 Standard Specification for Rigid Poly (Vinyl Chloride) (PVC)
Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds.
ASTM D1785 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe,
Schedules 40, 80 and 120.

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
ASTM D2467 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe
Fittings, Schedule 80.
ASTM D3567 Standard Practice for Determining Dimensions of Fiberglass (Glass-Fiber
Reinforced Thermosetting Resin) Pipe and Fittings R (2002).
ASTM D4024 Standard Specification for Machine Made "Fiberglass" (Glass-Fiber
Reinforced Thermosetting Resin) Flanges (2000).
ASTM F1173 Standard Specification for Thermosetting Resin Fiberglass Pipe Systems
to be used for Marine Applications (2001).
ASTM F1387 Standard Specification for Performance of Piping and Tubing
Mechanically Attached Fittings
ASTM F439 Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC)
Plastic Pipe Fittings, Schedule 80.
BSI BS 1873 Stell Globe and Globe Stop and Check Valves (flanged and butt welding
ends) for the Petroleum, Petrochemical and Allied Industries.
BSI BS 3799 Steel Pipe Fittings, Screwed and Socket Welding for the Petroleum
Industry.
BSI BS 5152 Cast Iron Globe and Globe Stop and Check Valves for General Purposes.
BSI BS 5351 Steel Ball Valves for the Petroleum, Petrochemical and Allied Industries.
BSI BS 5352 Steel Wedge Gate, Globe and Check Valves 50 mm and Smaller for the
Petroleum, Petrochemical and Allied Industries.
EEMUA 144 90/10 Copper Nickel Alloy Piping for Offshore Applications. Tubes
Seamless and Welded.
EEMUA 145 90/10 Copper Nickel Alloy Piping for Offshore Applications. Flanges
Composite and Solid.
EEMUA 146 90/10 Copper Nickel Alloy Piping for Offshore Applications. Fittings.
IMO A 753(18) International Maritime Organization Resolution A 753(18).
IOGP S-562 Supplementary Requirements to API Specification 6D Ball Valves
IOGP S-563 Material Data Sheets for Piping and Valve Components
IOGP S-611 Supplementary Requirements to API 600 Steel Gate Valves and to API
603 CRA Gate Valves
ISO 15156 Petroleum and natural gas industries: Materials for use in H2S
containing environments in oil and gas production.
ISO 14692 Petroleum and natural gas industries: Glass reinforced plastic (GRP)
piping.
ISO 17292 Metal ball valves for petroleum, petrochemical and allied industries.
ISO 21457 Petroleum, petrochemical and natural gas industries – Material selection
and corrosion control for oil and gas production systems.
ISO 27509 Petroleum and natural gas industries: Compact Flanged connections with
IX seal ring (First Edition).
MSS SP 6 Standard Finishes for Contact Faces de Pipe Flanges and Connecting End
Flanges of Valves and Fittings.
MSS SP70 Cast Iron Gate Valves, Flanged and Threaded Ends.
MSS SP 71 Gray Iron Swing Check Valves, Flanged and Threaded Ends.
MSS SP 72 Ball Valves with Flanged or Butt Welding Ends for General Service.
MSS SP 75 Strength, Wrought, Butt Welding Fittings.
MSS SP 80 Bronze Gate, Globe, Angle and Check Valves.
MSS SP 83 Steel Pipe Unions, Socket Welding and Threaded.

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
MSS SP 88 Diaphragm Type Valves.

MSS SP 95 Swage (d) Nipples and Bull Plugs.
MSS SP 97 Integrally Reinforced Forged Branch Outlet Fittings – Socket Welding,
Threaded, and Buttwelding Ends.
NBR 15827 Industrial Valves for Installations of Exploration, Production, Refining
and Transport of Petroleum Products - Requirements for Design and
Prototype Test.
NORSOK M-001 Materials Selection
3 SYMBOLS AND ABBREVIATED TERMS
For the purposes of this document, the following symbols and abbreviated terms apply:
AISI American Iron and Steel Institute

API American Petroleum Institute
ASME American Society of Mechanical Engineering
ASTM American Society for Testing And Materials
BE Beveled Ends
BF Butt Strap
BLE Beveled Large Ends.
BS Bell Spigot
CL Class
CPVC Chlorinated Polyvinyl Chloride
Cr Chrome
CS Carbon Steel
CuNi Copper-Nickel
DSS Duplex Stainless Steel
EEMUA Engineering Equipment and Materials Users Association
EJ Elastic Joint
FLG Flange
FF Flat Face
FRP Fiber reinforced plastic
FCAP Capilar Union Female
FTHD Threaded Female
GALV Galvanized
GR Grade
GRP Glass Fiber Reinforced Plastic
HC Half Coupling
HEX Hexagonal
IMO International Maritime Association
IN Inch
LTCS Low Temperature Carbon Steel
MAX Maximum
MCap Capilar Union Male
MSS Manufacturers Standardization Society of the Valve and Fittings Industry
MTHD ‘ Threaded Male
NACE National Association of Corrosion Engineers
NPT National Pipe Thread (Thread ASME B1.20.1)
NSFHT National Standard Fire Hose Thread (Thread)
Org coat Organic Coated
PBE Plain Both Ends

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
PE Plain Ends
PSE Plain Short Ends.
PSI Pounds per square inch
PTFE Polytetrafluoroethylene
PVC Polyvinyl Chloride
RF Raised Face
RJ Rigid Joint
RTEE Reduction Tee
RTJ Ring Type Joint
SCH Schedule
SDL Saddle
SDSS Super duplex Stainless Steel
SDV Shut Down Valve
SML Seamless
SOC Sockolet
SPEC Piping Material Specification
SS Stainless Steel
STD Standard
SW Socket Weld
TBE Threaded Both Ends
TEE Tee
THD Threaded
UNS Unified Numbering System
VAG Needle Valve
VAGI Instrumentation Needle Valve
VAX Axial Valve
VBO Butterfly Valve
VDE Double Ball valve
VDI Diaphragm Valve
VES Ball Valve
VESI Instrumentation Ball Valve
VGA Gate Valve
VGL Globe Valve
VMA Plug valve
VPVC Plastic valve
VRE Check Valve
WOL Weldolet
XS Extra Strong
XXS Double Extra Strong
WLD Welded
WN Weld Neck
WOL Weldolet
WPS Welding Procedure Specification
WPQR Welding Procedure Qualification Record

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
4 PIPING TAGGING SYSTEM
4.1. GENERAL
A–B–C–D–E
A – Nominal Pipe Size
Non-Integer Nominal Pipe Sizes shall be written as Fractions using a dash (“–”) to separate the
integer part from the fraction, if necessary. Example: 1/2, 3/4, 1-1/2, 2-1/2.
The number/fraction shall be followed by the double prime symbol (”) representative of inch
unit, never two (’) prime symbols. The sequential numbering need not be modified for diameter
changes in the same line.
B – Service Symbols (as listed in Item 5)
C – Piping Material Specification Code
D – Sequential Numbering of Line

Shall consist of sequential number containing exactly 4 digits. The sequential numbering
system shall be unique for each service. For example: 1/2"-P-B10-0010 (P-0010) and 8"-P-
B14-0010 (P-0010) is not allowed. For example: 6"-P-B10-0010 (P-0010) and 8"-P-B10-0010
(P-0010) is allowed within the same line.
E – Insulation:
PP – Personal Protection
HC – Heat Conservation
CC – Cold Conservation
NI – Not Insulated (Absence of insulation shall always be represented by “NI”)
Note: Piperun tag shall not contain any spaces between characters.
4.2. EXAMPLE OF PIPING TAG
1–1/2”–P–B10–0010–HC
Nominal Pipe Size: 1 1/2 inch
Service: P - Process
Piping Material Specification: B10
Sequential Numbering: 0010
Insulation: Heat Conservation
4.3. PIPELINE TAGGING FOR 3D MODELLING
B–D
For 3D modelling, where Pipeline tagging is also required, it shall consist only of Service and
sequential. Additional information regarding nominal pipe size, specification and insulation shall
be associated with the piperun. Example of pipeline tag:
P–0010
Service: Process (non-corrosive Hydrocarbon)

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
Sequential Numbering: 0010

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
5 PIPING SPECIFICATIONS X SERVICES
Code Service Specs
ADW Aerated Dilution Water B11, B23
AM Amine B10, B16, B3, B9, C10, C16, E10, E16, E3

B3, B10, C10, E10, F10, G10, R3B, R3C, R9B, R9C, S3B, S3C, S9B,
BG Inert Gas
S9C
CHW Chilled Water B1, B10, B20, R9B, R9C, S9B, S9C
Chemical Injection (non-
CI B1, B10, C10, E10, F10, G10, S9B, S9C, T12, T3, T60A, T60B
corrosive)
CI2 DBNPA Biocide B27
CN Sodium Hypochlorite B14, B20, B27
Corrosive Chemical Injection

CNI B3, C3, E3, F3, G3, H16, H3, J12, S3B, S3C, T3A, T3B, T60A, T60B
(Except Sodium Hypochlorite)
D Diesel B10, B3, C10, C3, H10
DA Open Drain B14, B22, B23, B25, B9, R9B, R9C, S9B, S9C
Closed Drain (Non-Corrosive
DF B1, B10
hydrocarbon)
Closed Drain (Corrosive
DFC B9
Hydrocarbon)
DO Carbon Dioxide (DRY) C8, E8
DOH Carbon Dioxide w/ Hydrocarbon J12P, J31, J31P
DW Distilled Water B3, R3B, R3C, S3B, S3C

B10, B12, B16, B19, B3, B30, B50, B6, B9, C3, C6, C19, C3, C6, H3,
F Safety System and Flare
H12, J40
FG Fuel Gas B10, B19, B3, B6, C10, C3, E10, E3, E6, F10, F3, G3
FL Foam Line B1, B10, B7, B7R
FLC Concentrated Foam B3
FP Production and Drilling Fluid B5, C5, E5, F5, G5, H5
FW Fire Water (Sea Water) B24, B7, B7R, S7
G Glycol B10, B3, B6, C10, C3, C6, E10, E3, E6, F10, F3, G10, G3, G6, H6
Refrigerated Liquified Petroleum

GL B6, C6, E6, F6, G6
Gases in Low Temperature
H Hydraulic Fluid B3, C3, E3, F3, G3, H3, S3B, S3C
HF Hot Fluid B4, C4
HWP Process Heating Water B4, C4, E4
HWU Utility Heating Water B21, B22, B23, B4

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
Code Service Specs
IA Instrumentation Air B3, G3, R3B, R3C, S3B, S3C
IG Instrumentation Gas B3
IGN Ignition Line B3
IN Instrumentation Nitrogen B3, R3B, R3C, S3B, S3C

B10, B14, B23, B30, C10, C14, C30, E10, E14, F10, F14, G10, G14,
IW De-Aerated Sea Water Injection
H12, H30
IWC Aerated Sea Water Injection B14, B22, B23
JF Helicopter Refueling B3
OL Lubrificating Oil B10, R9B, R9C, S9B, S9C
Process (non-corrosive B10, B6, C10, C10P, C6, E10, E3, E6, F10, F3, F6, G10, G3, G6, H10,
P
hydrocarbon) H10P, H12, H12P, H3, H31, H6, J10, J12, J12P, J40, J40P
B11, B12, B16, B17, B19, B3, B30, B9, C11, C12, C16, C19, C3, C30, C9,
PC Process (Corrosive Hydrocarbon) E16, E17, E19, E3, E30, E32, E9, F16, F3, F30, F32, G12, G12P, G16,
G16P, G19, G3, H12, H12P, H16, H3, H30, J12, J12P, J40, J40P
PCW Produced water B11, B12, B25, B26, C11, C12, C30, E11, F11, G11, H11
PW Potable Water B20, B3, R3B, R3C, S3B, S3C
PWH Hot Fresh Water B21, B22, B23, B3, S3B, S3C
S Steam B4, C4, E4, F4, G4, S9B, S9C
SA Service Air B1, B10, C10, R9B, R9C, S9B, S9C
SC Steam Condensate B4, C4, E4, F4, G4, S9B, S9C
SFW Fire Water (Fresh Water) A4
SN Start-up Nitrogen B1, B10, C10, R9B, R9C, S9B, S9C
STA Start-up Air C10H
SW Sea water B14, B22, B23, B7R, C14, C23

B1, B10, B20, B22, B23, B3, C10, E10, F10, G10, H10, R9B, R9C, S9B,
W Industrial water
S9C

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
6 PIPING SPECIFICATIONS
CORROSION MIN MAX

PRESSURE
SPEC ALLOWANCE TEMP TEMP PIPE MATERIAL SERVICE CODE
CLASS
(mm) (ºC) (ºC)
B10 150 1.6 mm Carbon Steel AM BG CHW CI D DF F FG FL G IW

-29 200
OL P SA SN W
B11 150 - 0 150 Organic Coat CS ADW PC PCW
B12 150 - 0 140 Super Duplex F PC PCW
B14 150 - 0 70 Organic Coat CS CN DA IW IWC SW
B16 150 - -46 130 Duplex AM F PC
B19 150 3.2 mm -46 210 Low Temp CS F FG PC
B20 - - 23 40 PVC CHW CN PW W
B21 - - 27 80 CPVC HWU PWH
B22 10 bar - 15 90 FRP DA HWU IW IWC PWH SW W
B23 16 bar - 15 90 FRP ADW DA HWU IW IWC PWH SW W
B27 16 bar - 15 85 FRP CI2 CN
B3 150 - SS 316/316L AM BG CNI D DW F FG FLC G H IA

-100 260
IG IGN IN JF PC PW PWH W
B30 150 - 0 240 CS Inconel Clad. F IW PC
B4 150 1.6 mm 0 300 Carbon Steel HF HWP HWU S SC
B50 150 - 38 538 SS 310H #N/D
B6 150 1.6 mm -46 240 Low Temp CS F FG G GL P
B7 20 bar - 0 75 Copper-Nickel FL FW
B9 150 3.2 mm -29 240 Carbon Steel AM DA DFC F PC
C10 300 1.6 mm 0 240 Carbon Steel AM BG CI D FG G IW P SA SN W
C11 300 - 0 150 Organic Coat CS ADW PCW PC
C12 300 - -50 140 Super Duplex PC PCW
C16 300 - -46 150 Duplex AM PC
C19 300 3.2 mm -46 200 Low Temp CS F PC
C23 25 bar - 90 90 FRP ADW SW
C3 300 - -100 150 SS 316/316L CNI D F FG G H PC
C30 300 - -20 200 CS Inconel Clad. IW PC PCW
C4 300 1.6 mm 0 350 Carbon Steel HF HWP S SC
C6 300 1.6 mm -46 110 Low Temp CS F G GL P
C9 300 3.2 mm 0 240 Carbon Steel PC
E10 600 1.6 mm -20 210 Carbon Steel AM BG CI FG G IW P W
E16 600 - -46 130 Duplex AM PC
E19 600 3.2 mm -46 180 Low Temp CS PC
E3 600 - -100 200 SS 316/316L AM CNI FG G H P PC

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
CORROSION MIN MAX

PRESSURE
SPEC ALLOWANCE TEMP TEMP PIPE MATERIAL SERVICE CODE
CLASS
(mm) (ºC) (ºC)
E30 600 - -20 200 CS Inconel Clad. PC

E6 600 1.6 mm -46 180 Low Temp CS FG G GL P
E8 600 - -18 54 Galv. CS DO
F3 900 - -100 215 SS 316/316L CNI FG G H P PC
F6 900 1.6 mm -46 320 Low Temp CS GL P
G3 1500 - -100 210 SS 316/316L CNI FG G H IA P PC
G10 1500 1.6 mm -20 200 Carbon Steel BG CI G IW P W
G12 1500 - -46 90 Super Duplex PC
H10 2500 1.6 mm -20 175 Carbon Steel DPW
H12 2500 - -50 190 Super Duplex CNI D F IW P PC
H12P 2500 - -50 115 Super Duplex P PC
H16 2500 - -50 130 Duplex CNI PC
H3 2500 - -100 150 SS 316/316L CNI F H P PC
H30 2500 - -20 120 CS Inconel Clad. IW PC
H6 2500 1.6 mm -46 180 Low Temp CS GP
J12 10000 - -50 120 Super Duplex CNI P PC
J12P 10000 - -50 120 Super Duplex DOH P PC
J40 10000 - -100 155 Inconel F P PC
J40P 10000 - -100 155 Inconel P PC
T3A - - 0 60 Tubing SS316/316L CI CNI
T3B - - 0 60 Tubing SS316/316L CI CNI
T60A - - 0 60 Tubing 6Mo CI CNI
T60B - - 0 60 Tubing 6Mo CI CNI

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
7 PIPING SPECIFICATION CODE RULE

SPEC CODE RULE: XYYZ
Material Code YY Pressure Class or Type Code X
Stainless Steel 316L 3 125 A

Carbon Steel API 5L, 1,6mm 4 150 B
Carbon Steel API 5L, 3,2mm 5 300 C
Low Temperature Carbon Steel ASTM A333 Gr6 e 6 600 E
ASTM A671 CC60, 1,6mm
Cu-Ni 90/10 7 900 F
Galvanized Carbon Steel API 5L 8 1500 G
Carbon Steel API 5L, 3,2mm 9 2500 H
Carbon Steel API 5L, 1,6mm 10 10000 J
Organic Coated Carbon Steel API 5L 11 Gasket Mechanical Coupling R

(GMC)
Super Duplex Steel UNS S32760 12 Mechanically Attached Fittings S

(MAF)
Organic Coated Carbon Steel API 5L 14 Tubing T
Duplex Steel UNS S31803 16
Carbon Steel API 5L, 6,4mm 17 Other Code Z

chracteristics
Low Temperature Carbon Steel ASTM A333 Gr6 e 19 Reduced Pressure R
ASTM A671 CC60, 3,2mm
PVC 20 ASME B31.4 or B31.8 P

CPVC 21 Hull Piping Spec. H
FRP 90°C 10 bar 22 Class 150 B
FRP 90°C 16 bar 23 Class 300 C

FRP 120°C 16 bar 24
RPVC 25
FRP 120°C 16 bar 26
FRP 85°C 16 bar 27
Inconel 625 cladded Carbon Steel API 5L 30
Alloy Steel 9Ni ASTM A 333 Gr8 31
Inconel 625 cladded Alloy Steel 3 1/2Ni ASTM A

32
333 Gr3
Inconel cladded Alloy Steel Aço Liga 9Ni ASTM A 33

333 Gr8
Inconel 625 UNS N06625 40

REV.
AREA: SHEET
TITLE:
INTERNAL
ESUP
8 PIPING MATERIAL SPECIFICATIONS

Doc: Rev ision: Sheet:
OF F SHORE PRODUCT ION F ACILIT IES I-E T-3010.2D-1200-200- A 1 of 2
P 4X-001
Issued by : Code: Corr. Allow .:
P IP IN G S P E C IFIC A TION FOR TOP S IDE S
S RGE /E S U P A S M E B 31.3 -
Serv ices (see notes): Material: Class: Standard:

AM - Amine; BG - Inert Gas; C N I - Corrosive Chemical Injection (Ex cept Sodium Hypochlorite); D - Diesel; D W - Distilled Water; F - Safety System and Flare; F G - Fuel Gas; F L C -
SS 150 B3
Concentrated Foam; G - Glycol; H - Hydraulic Fluid; IA - Instrumentation Air; IG - Instrumentation Gas; IGN - Ignition Line; IN - Instrumentation Nitrogen; J F - Aviation Kerosene; PC
- Process (Corrosive Hydrocarbon); PW - Potable Water; PW H - Hot Fresh Water; W - Industrial water; 316/316L
Pressure Rating (see notes)
Te mp e rature (°C) -100 38 100 150 250 260
Max Pre ssure (b arg ) 19.0 19.0 16.2 14.8 12.1 11.7
Pipes and Fittings (see notes)
Item s Code Size Wall Class Ends Standard M aterial
T-322 ½" - 1 ½" PE ASME B36.19 ASTM A312 TP 316/316L SML
S-40S
Pipes
2" - 24"
Pipe -
T-323 26" - 36" 0.375" BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
38" - 44" 0.438"
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Coupling C06-43 - 3000 SW
ASTM A182 Gr F316/316L
Cap C11-43
Sockolet C55-43 MSS SP-97
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Red Coupling C08-43
Fittings
Weldolet C12-43 2" - 20" MSS SP-97

90 LR Elbow C15-44
45 LR Elbow C16-44
90 SR Elbow C17-44
2" - 44"
Tee C20-44
According to pipe - BE
Cap C22-44 ASME B16.9 ASTM A403 Gr WP316/316L
Cross C24-44
Conc. Red C18-44
Ecc. Red C19-44 3" - 44"
Red Tee C21-44
Straight Nipple N-S145 ½" - 1 ½" ASTM A733 ASTM A312 TP316/316L
PBE
N-C144 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-C444 2" - 4" According to pipe - BLE x PSE
MSS SP-95 ASTM A403 Gr WP316/316L
N-E144 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E444 2" - 4" BLE x PSE
Socket Weld (SW) F-150-JX ½" - 1 ½"
ASME B16.5
2" - 24" Class 150 Raised Face
Welding Neck (WN) F-150-KX
Flanges
26" - 44" ASME B16.47 A

F-350-4X ½" - 3" According to pipe max 350 bar - ISO 6162-1 ASTM A182 Gr F316/316L
Blind ½" - 24" ASME B16.5
F-150-LX Class 150 Raised Face
26" - 44" ASME B16.47 A
Hyd One-Piece Flange F-350-3X ½" - 3" max 350 bar - ISO 6162-1
Nuts Gasket
Spiral-Wound J-150-EH ½" - 44" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
A320 L7, Zn-Ni

Paddles Stud &
Stud and Nuts P-150-08 ½" - 1 ½" - - - ASME B1.1

A194 7L, Zn-Ni
Figure-8 Blank R8-150-RS ½" - 14"
Paddle Blank RA-150-RS According to pipe 150 Raised Face ASME - Stainless Steel ASTM A240 316
16" - 44" B16.5
Paddle Spacer RE-150-RS
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
P 4X-001
Material: Class: Standard:
P IP IN G S P E C IFIC A TION FOR TOP S IDE S SS 150 B3
316/316L
Valv es (see notes)
Type Size CODE Tem p Type Size CODE Tem p Type Size CODE Tem p Type Size CODE Tem p
VAG-3000-1-S201 -100C to 200C VES-801-3-S2F1 -30C to 150C VES-150-2-S27F VDE-150-2-S206 -100C to 200C
-100C to 200C
VAG-3000-1-S202 -100C to 400C ½" - 1 ½" VES-801-3-S2F2 -46C to 150C VES-150-2-S27G VDE-150-2-S207
Needle ½" - 1 ½" -100C to 340C
VAG-3000-1-S2F1 -100C to 200C VES-801-3-S2F5 -100C to 200C VES-150-2-S280 VDE-150-2-S208
VAG-3000-1-S2F2 -100C to 400C VES-150-1-S210 -30C to 150C VES-150-2-S282 -100C to 400C VDE-150-2-S2F1
-30C to 150C
6" - 20" VBO-250-1-U291 VES-150-1-S220 VES-150-2-S28G VDE-150-2-S2F2
0C to 75C 0C to 150C
24" - 32" VBO-250-1-U293 VES-150-1-S226 VES-150-3-S216 Double ½" - 2" VDE-150-2-S2F3
-100C to 150C
6" - 20" VBO-150-2-S211 VES-150-1-S230 -46C to 150C VES-150-3-S217 -30C to 150C Ball VDE-150-2-S2F4
-46C to 150C
24" - 32" VBO-150-2-S213 VES-150-2-S210 VES-150-3-S21G VDE-150-2-S2F5
-100C to 200C
6" - 20" VBO-150-2-S231 VES-150-2-S216 VES-150-3-S227 0C to 150C VDE-150-2-S2F6
Butterfly -100C to 200C -30C to 150C
24" - 32" VBO-150-2-S233 VES-150-2-S21F VES-150-3-S230 VDE-150-2-S2F7
-100C to 340C
6" - 20" VBO-150-3-S221 VES-150-2-S21G Ball 2" - 36" VES-150-3-S237 -46C to 150C VDE-150-2-S2F8
24" - 30" VBO-150-3-S223 VES-150-2-S220 VES-150-3-S23G 3" - 8" VDE-150-2-S271 -100C to 200C
-100C to 345C 0C to 150C
6" - 20" VBO-150-3-S261 VES-150-2-S226 VES-150-3-S253 ½" - 1 ½" VGA-801-1-S201 -46C to 450C
Ball -30C to 150C
24" - 30" VBO-150-3-S263 VES-150-2-S230 VES-150-3-S25G Gate VGA-150-1-S231
2" - 36" -46C to 400C
VES-801-1-S201 -30C to 150C 2" - 36" VES-150-2-S236 VES-150-3-S263 VGA-150-2-S231
-46C to 150C 0C to 210C
VES-801-1-S202 -46C to 150C VES-150-2-S23F VES-150-3-S26G VGL-150-1-S201 -29C to 400C
VES-801-1-S205 -100C to 200C VES-150-2-S23G VES-150-3-S272 Globe 2" - 18" VGL-150-2-S201
-100C to 400C
VES-801-2-S201 -30C to 150C VES-150-2-S250 VES-150-3-S273 -100C to 200C VGL-150-2-S2F1
VES-801-2-S202 -46C to 150C VES-150-2-S252 VES-150-3-S27G Plug 2" - 24" VMA-150-2-S201 -30C to 110C
-30C to 150C
VES-801-2-S205 -100C to 200C VES-150-2-S25F VES-150-3-S283 VRE-800-1-S202
Ball ½" - 1 ½" -100C to 400C ½" - 1 ½" -100C to 400C
VES-801-2-S206 -46C to 150C VES-150-2-S25G VES-150-3-S28G VRE-800-2-S202
VES-801-2-S2F1 -30C to 150C VES-150-2-S260 VDE-150-2-S201 VRE-150-1-S211 0C to 150C
-30C to 150C
VES-801-2-S2F2 -46C to 150C VES-150-2-S262 0C to 210C VDE-150-2-S202 Check VRE-150-1-S212
VES-801-2-S2F5 -100C to 200C VES-150-2-S26F Double ½" - 2" VDE-150-2-S203 2" - 32" VRE-150-2-S212 -100C to 400C
Ball -100C to 150C
VES-801-2-S2F6 -46C to 150C VES-150-2-S270 VDE-150-2-S204 VRE-150-2-S215
-100C to 200C
VES-801-3-S205 -100C to 200C VES-150-2-S272 VDE-150-2-S205 -100C to 200C VRE-150-2-S235 -100C to 200C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
1 RTEE RTEE TEE WOL - Weldolet
1.5 RTEE RTEE RTEE TEE
2 SOC SOC SOC SOC TEE
3 SOC SOC SOC SOC RTEE TEE TEE - Tee
4 SOC SOC SOC SOC RTEE RTEE TEE
6 SOC SOC SOC SOC WOL RTEE RTEE TEE
8 SOC SOC SOC SOC WOL WOL RTEE RTEE TEE RTEE - Red Tee
10 SOC SOC SOC SOC WOL WOL WOL RTEE RTEE TEE
12 SOC SOC SOC SOC WOL WOL WOL RTEE RTEE RTEE TEE
14 SOC SOC SOC SOC WOL WOL WOL WOL RTEE RTEE RTEE TEE HC - Half Coupling
16 SOC SOC SOC SOC WOL WOL WOL WOL RTEE RTEE RTEE RTEE TEE
18 SOC SOC SOC SOC WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE TEE
20 SOC SOC SOC SOC WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE SOC - Sockolet
24 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
26 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
28 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE TEE
30 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE TEE
32 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
34 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
36 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
38 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
40 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
42 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
44 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36 38 40 42 44
BRANCH SIZE
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 do not hav e flange protectors or otherw ise denied direct atmospheric ex posure or it is not in direct open seaw ater ex posure. (see A.2.2.4 from ISO 15156-2)
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding.
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
51 Stainless Steel ex ternal coating shall be applied for the temperature limits according to I-ET-3010.00-1200-956-P4X-002 - General Painting.
54 This spec for PC serv ice should only be used w hen recommended in annex D.
57 All standardized pipe w all thickness herein listed are calculated considering only internal pressure. Other loads resulting of the piping analy sis (supporting, flex ibility , fadigue) may increase
minimum required thickness.
59 In case of use this spec below -30 °C, the material shall be furnished w ith solution heat treatment.
62 This spec for Amine serv ice is applicable for piping dow nstream the Amine stripper up to booster pump suction.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
Materials listed in this spec shall meet the requirements described in the notes and annex es of this document and also the requirements of the specific data sheet in IOGP S-563 as applicable. In
125 case of conflict of criteria Petrobras shall be consulted. It shall be highlighted that the IOGP requirements is not applicable for: inconel 625 coating, w hich shall follow I-ET-3010.00-1200-955-P4X-
001; supplementary NACE requirement for carbon steel w hich shall follow Annex D; and coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
146 Seamless pipe is acceptable in place of w elded pipe. The thickness need to be updated by designer.
156 Studs ASTM A 320 L7 are acceptable bolting material for sour serv ice since it is not ex posed directly to a sour env ironment, not buried, not insulated, not equipped w ith flange protectors or
otherw ise denied direct atmospheric ex posure or it is not in direct open seaw ater ex posure. (see A.2.2.4 from ISO 15156-2)
P 4X-001
S RGE /E S U P A S M E B 31.3 1.6 mm

H F - Hot Fluid; H W P - Process Heating Water; H W U - Utility Heating Water; S - Steam; SC - Steam Condensate;
Carbon 150 B4
Steel
Te mp e rature (°C) 0 38 50 100 150 200 250 300
Max Pre ssure (b arg ) 19.6 19.6 19.2 17.7 15.8 13.8 12.1 10.2
½" - 1 ½" XS PE API 5L Gr B PSL 1 SML
2" - 6" STD
8" - 12" S-20 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
Pipes
SAW)
Pipe T-102 14" - ASME B36.10
S-10 BE
16" - 18"
20" 0.281" API 5L Gr B PSL 1 WLD (HFW or SAW)
24" 0.312"
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
ASTM A105
Cap C11-02
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Red Coupling C08-02
Fittings

90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
2" - 24"
Tee C20-03
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 24"
Red Tee C21-03
Straight Nipple N-S120 ½" - 1 ½" ASTM A733 API 5L Gr B PSL 1 seamless
PBE
N-C103 ¾" - 1 ½"
Nipple
Swage Conc Nipple

MSS SP-95 ASTM A234 Gr WPB
N-E103 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E403 2" - 4" BLE x PSE
Nuts Gasket Flanges
Socket Weld (SW) F-150-J2 ½" - 1 ½"

Welding Neck (WN) F-150-K2 2" - 24" According to pipe Class 150 Raised Face ASME B16.5 ASTM A105
Blind F-150-L2 ½" - 24"
A193 B7
Paddles Stud &
Stud and Nuts P-150-01 ½" - 1 ¼" - - - ASME B1.1

A194 Gr 2H
Figure-8 Blank R8-150-RC ½" - 14"
Paddle Blank RA-150-RC According to pipe 150 Raised Face ASME - Carbon Steel ASTM A516 GR60
16" - 24" B16.5
Paddle Spacer RE-150-RC
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Carbon 150 B4
Steel
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-802-2-C105 Ball 2" - 24" VES-150-3-C163 0C to 210C Gate 2" - 24" VGA-150-2-C132 -29C to 400C
Needle ½" - 1 ½" ½" - 1 ½" -29C to 210C
VAG-3000-1-S202 -100C to 400C VES-802-3-C105 VGA-801-1-C101 VGL-150-1-C102
Globe 2" - 18" -29C to 400C
6" - 20" VBO-150-2-C111 -29C to 150C VES-150-1-C160 ½" - 1 ½" VGA-801-1-C102 VGL-150-2-C102
24" VBO-150-2-C113 -29C to 200C Ball VES-150-1-C162 VGA-801-2-C101 ½" - 1 ½" VRE-800-1-C103
Butterfly Gate -29C to 400C
6" - 20" VBO-150-3-C161 2" - 24" VES-150-2-C160 0C to 210C VGA-150-1-C131 Check VRE-150-1-C113 -29C to 400C
-29C to 240C 2" - 24"
24" VBO-150-3-C163 VES-150-2-C162 2" - 24" VGA-150-1-C132 VRE-150-2-C113
Ball ½" - 1 ½" VES-802-1-C105 -29C to 210C VES-150-3-C162 VGA-150-2-C131
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24
BRANCH SIZE
Notes
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
P 4X-001

F - Safety System and Flare; F G - Fuel Gas; G - Glycol; GL - Refrigerated Liquified Petroleum Gases in Low Temperature; P - Process (non-corrosive hydrocarbon);
Low T emp 150 B6
CS
Te mp e rature (°C) -46 0 38 50 100 150 200 240
½" - 1 ½" S-160 PE
2" - 6" STD
T-105 ASTM A333 Gr 6 SML
Pipes
8" - 12" S-20

Pipe - ASME B36.10
14" BE
S-10
16" - 30"
T-106 ASTM A671 Gr CC60 Class 22 WLD
32" - 36" STD
90 Elbow C01-04
45 Elbow C02-04
Tee C03-04
ASME B16.11
Cross C05-04 ½" - 1 ½"
ASTM A350 Gr LF2 Cl 1
Cap C11-04
Red Tee C04-04
¾" - 1 ½" ASME B16.11
Red Coupling C08-04
Fittings

90 LR Elbow C15-05
45 LR Elbow C16-05
90 SR Elbow C17-05
2" - 36"
Tee C20-05
Cap C22-05 ASME B16.9 ASTM A420 Gr WPL6
Cross C24-05
Conc. Red C18-05
Ecc. Red C19-05 3" - 36"
Red Tee C21-05
Straight Nipple N-S137 ½" - 1 ½" ASTM A733 ASTM A333 Gr 6
PBE
N-C105 ¾" - 1 ½"
Nipple
Swage Conc Nipple

MSS SP-95 ASTM A420 Gr WPL6
N-E105 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E405 2" - 4" BLE x PSE
Socket Weld (SW) F-150-J3½" - 1 ½"
ASME B16.5
Flanges
2" - 24"
Welding Neck (WN) F-150-K3
26" - 36" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A350 Gr LF2 Class 1
½" - 24" ASME B16.5
Blind F-150-L3
26" - 36" ASME B16.47 A
Nuts Gasket
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
Figure-8 Blank R8-150-RL ½" - 14"
Paddle Blank RA-150-RL According to pipe 150 Raised Face ASME - Low Temp. Carbon Steel ASTM A516 70 + S5
16" - 36" B16.5
Paddle Spacer RE-150-RL
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Low T emp 150 B6
CS
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-150-1-C250 -30C to 150C VES-150-3-C216 VDE-150-2-C208 -46C to 340C
VAG-3000-1-S202 -100C to 400C VES-150-1-C270 -46C to 200C VES-150-3-C217 -30C to 150C VDE-150-2-C2F1
Needle ½" - 1 ½" -30C to 150C
VAG-3000-1-S2F1 -100C to 200C VES-150-1-C280 -46C to 345C VES-150-3-C21G VDE-150-2-C2F2
VAG-3000-1-S2F2 -100C to 400C VES-150-2-C210 VES-150-3-C236 VDE-150-2-C2F3
-46C to 150C
6" - 20" VBO-150-2-C211 VES-150-2-C216 VES-150-3-C237 -46C to 150C ½" - 2" VDE-150-2-C2F4
-46C to 200C -30C to 150C
24" - 32" VBO-150-2-C213 VES-150-2-C21F VES-150-3-C23G Double VDE-150-2-C2F5
Butterfly Ball -46C to 200C
VBO-150-3-C261 VES-150-2-C21G VES-150-3-C252 VDE-150-2-C2F6
- -46C to 240C -30C to 150C
VBO-150-3-C263 VES-150-2-C230 Ball 2" - 36" VES-150-3-C253 VDE-150-2-C2F7
-46C to 340C
VES-803-1-C201 -30C to 150C VES-150-2-C236 VES-150-3-C25G -29C to 150C VDE-150-2-C2F8
-46C to 150C
VES-803-1-C205 -30C to 200C VES-150-2-C23F VES-150-3-C272 VDE-150-2-C215
-30C to 150C
VES-803-2-C201 -30C to 150C VES-150-2-C23G VES-150-3-C273 -46C to 200C 3" - 8" VDE-150-2-C21F
Ball 2" - 36"
VES-803-2-C202 -46C to 150C VES-150-2-C250 VES-150-3-C27G VDE-150-2-C235 -46C to 150C
VES-803-2-C205 -46C to 200C VES-150-2-C252 VES-150-3-C282 VGL-150-1-C201
-30C to 150C
VES-803-2-C2F1 -30C to 150C VES-150-2-C25F VES-150-3-C283 -46C to 345C Globe 2" - 18" VGL-150-2-C201 -46C to 345C
½" - 1 ½"
VES-803-2-C2F2 -46C to 150C VES-150-2-C25G VES-150-3-C28G VGL-150-2-C2F1
Ball
VES-803-2-C2F5 VES-150-2-C270 VDE-150-2-C201 Plug 2" - 24" VMA-150-2-C201 -30C to 110C
-46C to 200C -30C to 150C
VES-803-3-C205 VES-150-2-C272 VDE-150-2-C202 VRE-800-1-C202
-46C to 200C ½" - 1 ½" -46C to 345C
VES-803-3-C2F1 -30C to 150C VES-150-2-C27F VDE-150-2-C203 VRE-800-2-C202
Double ½" - 2" -46C to 150C
VES-803-3-C2F2 -46C to 150C VES-150-2-C27G Ball VDE-150-2-C204 VRE-150-1-C211 0C to 345C
Check
VES-803-3-C2F5 -46C to 200C VES-150-2-C280 VDE-150-2-C205 VRE-150-2-C212
-46C to 200C 2" - 32" -46C to 345C
VES-150-1-C210 -30C to 150C VES-150-2-C282 -46C to 345C VDE-150-2-C206 VRE-150-2-C215
2" - 36"
VES-150-1-C230 -46C to 150C VES-150-2-C28G VDE-150-2-C207 -46C to 340C VRE-150-2-C235 -46C to 210C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
BRANCH SIZE
Notes
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
P 4X-001

F L - Foam Line; F W - Fire Water (Sea Water);
Copper- 20 bar B7
Nickel
Te mp e rature (°C) 0 38 50 75
Max Pre ssure (b arg ) 19.6 19.6 19.2 18.4
½" - ¾" 2.0mm
PE
1" - 2"
2.5mm Cu-Ni 90/10 (UNS C7060X) SML
2 ½" - 3"
4" 3.0mm
6" 3.5mm
8" 4.5mm
10" 5.5mm
Cu-Ni 90/10 (UNS C7060X SML or WLD)
Pipes
12" 7.0mm
Pipe T-202 - EEMUA 234
14" 8.0mm
BE
16" 9.0mm
18" 9.5mm
20" 11.0mm
24" 13.0mm
Cu-Ni 90/10 (UNS C7060X) WLD
28" 15.0mm
32" 17.0mm
36" 19.0mm
90 Elbow C01-35
45 Elbow C02-35
Fcap
Tee C03-35
Coupling C06-35
Plug C09-35 ½" - 1 ½" 20 bar THD
Union C10-35
- Fcap
Cap C11-35
Connector C37-35
-
Connector Union C38-35
Sockolet C55-35 ½" - 2" - Cap
Fittings
Fcap
Red Coupling C08-35 EEMUA 234 Cu-Ni 90/10 (UNS C7060X)
¾" - 1 ½" 20 bar Mcap x Fcap
Bush C23-35 FTHD x Mcap
Weldolet C12-35 2" - 16"
90 LR Elbow C15-35
45 LR Elbow C16-35
2" - 36"
Tee C20-35 According to pipe
-
Cap C22-35 BE
Conc. Red C18-35
Ecc. Red C19-35 3" - 36"
Red Tee C21-35
Stub End WN-L C39-35 4" - 36" - 20 bar
N-A335 TBE
Nipple
Connector Nipple N-A735 ¾" - 1 ½" According to pipe - FTHD x Fcap EEMUA 234 Cu-Ni 90/10 (UNS C7060X)
N-A835 MTHD x Fcap
Slip on (SO) F-20-HM ½" - 1 ½" 20 bar EEMUA 234 Cu-Ni 90/10 (UNS 7060X)
Nuts Gasket Flanges
½" - 24" ASME B16.5

Blind F-150-LY According to pipe Class 150 Raised Face ASTM A105 Thermal Spray coated (note 126)
28" - 36" ASME B16.47 A
Backing Flange F-20-Y2 2" - 36" 20 bar EEMUA 234 ASTM A105
Flat type J-150-P4 ½" - 36" - Class 150 Raised Face ASME B16.21 Compressed sheet, fire-tested
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
½" - 1"
Figure-8 Blank R8-150-RT
1 ½" - 14" Raised Face ASME Carbon Steel ASTM A516 GR60 CurAl Thermal
According to pipe 150 B16.5 - Spray coated (note 126)
Paddle Blank RA-150-RT
16" - 36"
Paddle Spacer RE-150-RT
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Copper- 20 bar B7
Nickel
Valv es (see notes)
6" - 20" VBO-150-2-U311 VES-150-1-U300 Angular 2 ½" VAN-150-1-U101 0C to 75C VGL-150-1-U301
1" - 1 ½" Globe 2" - 18" 0C to 90C
24" - 36" VBO-150-2-U313 VES-150-2-U300 Gate ½" - 1 ½" VGA-200-1-U101 -29C to 75C VGL-150-2-U301
0C to 90C
6" - 20" VBO-150-2-U351 Ball 2" - 24" VES-150-1-U310 0C to 90C Globe ½" - 1 ½" VGL-150-1-U101 0C to 75C ½" - 1 ½" VRE-200-1-U122 0C to 75C
Butterfly
24" - 36" VBO-150-2-U353 VES-150-2-U310 VGA-150-1-U331 Check VRE-150-1-U311
2" - 4" Gate 1" 0C to 90C 2" - 36" 0C to 90C
6" - 20" VBO-150-3-U361 VES-150-2-U311 VGA-150-2-U331 VRE-150-1-U312
-29C to 75C
24" - 36" VBO-150-3-U363 Diaphragm 1 ½" - VDI-300-2-U301 0C to 80C
12"
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
1.5 RTEE RTEE RTEE TEE TEE
2.5 SOC SOC SOC SOC SOC RTEE TEE
3 SOC SOC SOC SOC SOC RTEE RTEE TEE
4 SOC SOC SOC SOC SOC RTEE RTEE RTEE TEE RTEE - Red Tee
6 SOC SOC SOC SOC SOC WOL WOL RTEE RTEE TEE
8 SOC SOC SOC SOC SOC WOL WOL WOL RTEE RTEE TEE
10 SOC SOC SOC SOC SOC WOL WOL WOL WOL RTEE RTEE TEE HC - Half Coupling
12 SOC SOC SOC SOC SOC WOL WOL WOL WOL RTEE RTEE RTEE TEE
14 SOC SOC SOC SOC SOC WOL WOL WOL WOL WOL RTEE RTEE RTEE TEE
16 SOC SOC SOC SOC SOC WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE TEE SOC - Sockolet
18 SOC SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE TEE
20 SOC SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
24 SOC SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
28 SOC SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
32 SOC SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
36 SOC SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
0.5 0.75 1 1.25 1.5 2 2.5 3 4 6 8 10 12 14 16 18 20 24 28 32 36
BRANCH SIZE
Notes
53 This spec must be used only for offshore facilities.
86 Pipes in this spec do not take account additional thickness for threads. Must be ev aluated pipes thicker than these here specified if threaded pipe w ill be applied.
87 Piping, connections and flanges should be specified according EEMUA 234.
104 The backing flange and stub ends are part of the composite flange according EEMUA 234.
110 Epox y coating for flanges shall be applied according to I-ET-3010.00-1200-956-P4X-002 - General Painting.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
126 Thermal spray application shall be according to the requirements of I-ET-3010.00-1200-956-P4X-003. Consumable specification: AWS C2.25m: W-CuAl-1 or ISO 14919: CuAl10.
143 Piping materiall shall be certified and approv ed by Classification Society for the intended serv ice.
152 SW connection may be used instead of capillary connection.
153 Backing flange in carbon steel shall be galv anized before painting.
P 4X-001

AM - Amine; D A - Open Drain; D F C - Closed Drain (Corrosive Hydrocarbon); F - Safety System and Flare; PC - Process (Corrosive Hydrocarbon);
Carbon 150 B9
Steel
Te mp e rature (°C) -29 0 38 50 100 150 200 240
½" - 1 ½" S-160 PE API 5L Gr B PSL 1 SML
2" XS
3" - 6" STD
SAW)
12" 0.281"
Pipes
14"
Pipe T-102 S-20 - ASME B36.10
16" - 18" BE
API 5L Gr B PSL 1 WLD (HFW or SAW)
20" - 24"
STD
26" - 28"
30" - 32" 0.406"
API 5L Gr B PSL 1 WLD SAW
34" 0.438"
36" 0.469"
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
ASTM A105
Cap C11-02
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Red Coupling C08-02
Fittings

90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
2" - 36"
Tee C20-03
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 36"
Red Tee C21-03
PBE
N-C103 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E103 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E403 2" - 4" BLE x PSE
ASME B16.5
Flanges
2" - 24"
26" - 36" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A105
½" - 24" ASME B16.5
Blind F-150-L2
26" - 36" ASME B16.47 A
Nuts Gasket
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
16" - 36" B16.5
P 4X-001
Steel
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-150-1-C130 VES-150-2-C182 VES-150-4-C174 0C to 210C
0C to 150C 0C to 400C Ball 6" - 36"
VAG-3000-1-S202 -100C to 400C VES-150-1-C150 VES-150-2-C18G VES-150-4-C184 0C to 400C
Needle ½" - 1 ½"
VAG-3000-1-S2F1 -100C to 200C VES-150-1-C160 VES-150-3-C116 VDE-150-2-C101
0C to 210C
VAG-3000-1-S2F2 -100C to 400C VES-150-1-C170 VES-150-3-C117 -29C to 150C VDE-150-2-C1F1 -29C to 150C
6" - 20" VBO-250-1-U291 VES-150-1-C180 0C to 400C VES-150-3-C11G VDE-150-2-C1F2
0C to 75C
24" - 32" VBO-250-1-U293 VES-150-2-C110 -29C to 150C VES-150-3-C126 Double ½" - 2" VDE-150-2-C1F5
-29C to 200C
6" - 20" VBO-150-2-C111 -29C to 150C VES-150-2-C116 0C to 150C VES-150-3-C127 Ball VDE-150-2-C1F6
24" VBO-150-2-C113 -29C to 200C VES-150-2-C11F -29C to 150C VES-150-3-C136 VDE-150-2-C1F7
Butterfly 0C to 150C -29C to 340C
6" - 20" VBO-150-2-C131 VES-150-2-C120 VES-150-3-C137 VDE-150-2-C1F8
24" VBO-150-2-C133 VES-150-2-C126 VES-150-3-C13G 3" - 8" VDE-150-2-C11F -29C to 150C
-29C to 240C
6" - 20" VBO-150-3-C161 VES-150-2-C130 2" - 36" VES-150-3-C152 ½" - 1 ½" VGA-801-1-C101
0C to 150C
24" - 26" VBO-150-3-C163 Ball 2" - 36" VES-150-2-C136 Ball VES-150-3-C153 Gate VGA-150-1-C131 -29C to 400C
-29C to 150C 2" - 36"
VES-803-1-C101 -29C to 150C VES-150-2-C13F VES-150-3-C15G VGA-150-2-C131
VES-803-1-C102 0C to 150C VES-150-2-C13G VES-150-3-C162 VGL-150-1-C101
2" - 18"
VES-803-1-C105 -29C to 210C VES-150-2-C150 -29C to 150C VES-150-3-C163 VGL-150-2-C101
Globe -29C to 400C
VES-803-2-C101 -29C to 150C VES-150-2-C152 0C to 150C VES-150-3-C172 0C to 210C VGL-150-2-C1F1
2" - 20"
VES-803-2-C102 0C to 150C VES-150-2-C160 VES-150-3-C173 VGL-150-2-C1F2
½" - 1 ½"
VES-803-2-C105 -29C to 210C VES-150-2-C162 VES-150-3-C17G Plug 2" - 24" VMA-150-2-C201 -30C to 110C
Ball
VES-803-2-C1F1 -29C to 150C VES-150-2-C170 VES-150-3-C182 ½" - 1 ½" VRE-800-2-C103 -29C to 400C
0C to 210C 0C to 400C
VES-803-2-C1F5 VES-150-2-C172 VES-150-3-C183 VRE-150-1-C111 0C to 150C
VES-803-3-C105 -29C to 210C VES-150-2-C17F VES-150-3-C18G -29C to 400C Check VRE-150-2-C112
2" - 32" -29C to 400C
VES-803-3-C1F5 VES-150-2-C17G VES-150-4-C154 0C to 150C VRE-150-2-C115
6" - 36"
VES-150-1-C110 -29C to 150C VES-150-2-C180 0C to 400C VES-150-4-C164 0C to 210C VRE-150-2-C135 -29C to 210C
2" - 36"
VES-150-1-C120 0C to 150C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
BRANCH SIZE
Notes
P 4X-001

AM - Amine; BG - Inert Gas; C H W - Chilled Water; C I - Chemical Injection (non-corrosive); D - Diesel; D F - Closed Drain (Non-Corrosive hydrocarbon); F - Safety System and
Carbon 150 B10
Flare; F G - Fuel Gas; F L - Foam Line; G - Glycol; IW - De-Aerated Sea Water Injection; OL - Lubrificating Oil; P - Process (non-corrosive hydrocarbon); SA - Service Compressed
Air (utility Air); SN - Start-up Nitrogen; W - Industrial water; Steel
Te mp e rature (°C) -29 0 38 50 100 150 200
Max Pre ssure (b arg ) 19.6 19.6 19.6 19.2 17.7 15.8 13.8
2" - 6" STD
SAW)
14"
S-10
16" - 18"
Pipes
Pipe T-102 24" 0.312" - ASME B36.10

BE
26" - 28" S-10
30" - 32" 0.344"
34" - 36" STD
38" - 40" 0.406"
42" 0.438"
44" 0.469"
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
ASTM A105
Cap C11-02
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Red Coupling C08-02
Fittings

90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
2" - 44"
Tee C20-03
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 44"
Red Tee C21-03
Straight Nipple N-S120½" - 1 ½" ASTM A733 API 5L Gr B PSL 1 seamless
PBE
N-C103¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E103¾" - 1 ½" PBE
Swage Ecc Nipple
N-E403 2" - 4" BLE x PSE
Socket Weld (SW) F-150-J2
½" - 1 ½"
ASME B16.5
Flanges
2" - 24"
½" - 24" ASME B16.5
Blind F-150-L2
26" - 44" ASME B16.47 A
Nuts Gasket
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
16" - 44" B16.5
P 4X-001
Steel
Valv es (see notes)
Ax ial VAC-150-1-C111 VES-803-2-C1F5 -29C to 210C VES-150-2-C160 VDE-150-2-C1F2 -29C to 150C
Control 28" - 32" -29C to 150C
VAG-3000-1-S201 -100C to 200C

VES-803-3-C101 -29C to 150C VES-150-2-C17F 0C to 210C VDE-150-2-C1F5
½" - 1 ½" -29C to 200C
VES-803-3-C105 VES-150-2-C17G ½" - 2" VDE-150-2-C1F6
VAG-3000-1-S202 -100C to 400C -29C to 210C
Needle ½" - 1 ½" VES-803-3-C1F5 VES-150-2-C18G 0C to 400C Double VDE-150-2-C1F7
VAG-3000-1-S2F1 -100C to 200C -29C to 340C
VES-150-1-C110 -29C to 150C VES-150-3-C116 Ball VDE-150-2-C1F8
VAG-3000-1-S2F2 -100C to 400C
VES-150-1-C120 VES-150-3-C117 -29C to 150C VDE-150-2-C114
2" - 20" VBO-250-1-U291
0C to 75C VES-150-1-C126 VES-150-3-C11G 3" - 8" VDE-150-2-C115 -29C to 150C
24" - 32" VBO-250-1-U293 0C to 150C
6" - 20" VBO-150-2-C111 -29C to 150C
VES-150-1-C130 VES-150-3-C126 VDE-150-2-C11F
VES-150-1-C150 Ball 2" - 36" VES-150-3-C127 ½" - 1 ½" VGA-801-1-C101
24" - 32" VBO-150-2-C113 -29C to 200C
6" - 20" VBO-150-2-C131 VES-150-1-C160 VES-150-3-C136 Gate VGA-150-1-C131 -29C to 400C
0C to 210C 0C to 150C 2" - 36"
-29C to 240C VES-150-1-C170 VES-150-3-C137 VGA-150-2-C131
24" - 32" VBO-150-2-C133
Butterfly VES-150-1-C180 0C to 400C VES-150-3-C13G VGL-150-1-C101
6" - 20" VBO-150-2-C151 Ball
-29C to 150C VES-150-2-C110 -29C to 150C VES-150-3-C152 VGL-150-2-C101
24" - 32" VBO-150-2-C153 Globe 2" - 20" -29C to 400C
6" - 20" VBO-150-3-C121 VES-150-2-C111 VES-150-3-C153 VGL-150-2-C1F1
2" - 36" 0C to 150C -29C to 150C
24" - 32" VBO-150-3-C123
VES-150-2-C116 VES-150-3-C15G VGL-150-2-C1F2
-29C to 240C VES-150-2-C11F -29C to 150C VES-150-3-C17G 0C to 210C Plug 2" - 24" VMA-150-2-C101 0C to 110C
6" - 20" VBO-150-3-C161
24" - 32" VBO-150-3-C163
VES-150-2-C120 VES-150-3-C18G -29C to 400C VRE-800-1-C102
VES-803-1-C101 -29C to 150C
VES-150-2-C126 VDE-150-2-C101 ½" - 1 ½" VRE-800-2-C102 -29C to 400C
-29C to 150C
VES-803-1-C102 0C to 150C
VES-150-2-C130 VDE-150-2-C102 VRE-800-2-C103
0C to 150C
VES-803-1-C105 -29C to 210C
VES-150-2-C136 VDE-150-2-C105 VRE-150-1-C111 0C to 150C
Double ½" - 2" -29C to 200C Check
Ball ½" - 1 ½" VES-803-2-C101 -29C to 150C
VES-150-2-C13F Ball VDE-150-2-C106 VRE-150-1-C112
2" - 32"
VES-803-2-C102 0C to 150C
VES-150-2-C13G VDE-150-2-C107 VRE-150-2-C112 -29C to 400C
-29C to 340C
VES-803-2-C105 -29C to 210C
VES-150-2-C150 -29C to 150C VDE-150-2-C108 VRE-150-2-C115
VES-150-2-C152 0C to 150C VDE-150-2-C1F1 -29C to 150C 1" - 32" VRE-150-2-C135 -29C to 210C
VES-803-2-C1F1 -29C to 150C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36 38 40 42 44
BRANCH SIZE
Notes
40 The IW serv ice is only applicable for onshore units.
43 The FL serv ice is only applicable for onshore units.
46 Diesel serv ice "D" is only applicable for piping upstream the centrifuge.
56 This spec for FG serv ice is applicable for piping upstream the filters.
64 This spec for Amine serv ice is applicable for piping dow nstream the regeneration unit and upstream the contactor unit.
P 4X-001

AD W - Aerated Dilution Water; PC - Process (Corrosive Hydrocarbon); PC W - Produced water;
Organic 150 B11
Coat CS
Te mp e rature (°C) 0 38 50 100 150
Max Pre ssure (b arg ) 19.6 19.6 19.2 17.7 15.8
1" - 1 ½" XS PE API 5L Gr B PSL 1 SML
2" - 6" STD
API 5L Gr B PSL 1 (SML or WLD HFW or WLD
Pipes
8" - 12" S-20 SAW)

Pipe T-102 - ASME B36.10
14" BE
16" - 24" S-10 API 5L Gr B PSL 1 WLD (HFW or SAW)
26" - 28" API 5L Gr B PSL 1 WLD SAW
Weldolet C12-02 1" - 12" MSS SP-97 ASTM A105
90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
1" - 28"
Fittings
Tee C20-03
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 1 ½" - 28"
Red Tee C21-03
Swage Conc Nipple N-C203
Nuts Gasket Flanges Nipple
1 ½" - 4" According to pipe - BBE MSS SP-95 ASTM A234 Gr WPB
Swage Ecc Nipple N-E203
1" - 24" ASME B16.5
26" - 28" ASME B16.47 A
According to pipe Class 150 Raised Face ASTM A105
1" - 24" ASME B16.5
Blind F-150-L2
26" - 28" ASME B16.47 A
Flat type J-150-PC 1" - 28" - Class 150 Raised Face ASME B16.21 Multidirectional Expanded PTFE
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
Figure-8 Blank R8-150-RP 1" - 14"
Paddle Blank RA-150-RP According to pipe 150 Raised Face ASME - Carbon Steel ASTM A516 GR60 epoxi coated
16" - 28" B16.5
Paddle Spacer RE-150-RP
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Organic 150 B11
Coat CS
Valv es (see notes)
Needle 1" - 1 ½" VAG-150-1-D201 -50C to 150C VES-150-2-D110 Ball 2" - 28" VES-150-3-D27G -46C to 150C VGL-150-1-D201 -46C to 150C
2" - 20" VBO-250-1-U284 VES-150-2-D210 VDE-150-1-D201 VGL-150-2-D101 0C to 150C
0C to 80C -30C to 150C Globe 2" - 18"
24" - 28" VBO-250-1-U286 VES-150-2-D21F VDE-150-2-D201 -30C to 150C VGL-150-2-D201
-46C to 150C
6" - 20" VBO-150-2-D211 -46C to 150C VES-150-2-D21G VDE-150-2-D202 VGL-150-2-D2F1
Butterfly
24" - 28" VBO-150-2-D213 -46C to 200C VES-150-2-D230 VDE-150-2-D203 1" - 1 ½" VRE-150-1-D205 -46C to 150C
Double 1" - 2" -46C to 150C
6" - 20" VBO-150-3-D261 VES-150-2-D23F -46C to 150C VDE-150-2-D204 VRE-150-1-D114
-46C to 150C Ball 2" - 28" Ball 0C to 150C
24" - 28" VBO-150-3-D263 VES-150-2-D23G VDE-150-2-D2F1 VRE-150-1-D211
-30C to 150C
VES-150-1-D200 VES-150-3-D217 VDE-150-2-D2F2 Check 2" - 28" VRE-150-1-D212
-30C to 150C -30C to 150C
1" - 1 ½" VES-150-2-D200 VES-150-3-D21G VDE-150-2-D2F3 VRE-150-2-D212
-46C to 150C -46C to 150C
Ball VES-150-2-D2F0 0C to 150C VES-150-3-D226 0C to 150C VDE-150-2-D2F4 VRE-150-2-D215
VES-150-1-D210 VES-150-3-D23G -46C to 150C VGA-150-1-D231 1" - 28" VRE-150-2-D235
2" - 28" -30C to 150C Gate 2" - 28" -50C to 150C
VES-150-1-D216 VES-150-3-D25G -30C to 150C VGA-150-2-D231
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
4 WOL WOL RTEE RTEE TEE
6 WOL WOL WOL RTEE RTEE TEE TEE - Tee
8 WOL WOL WOL WOL RTEE RTEE TEE
10 WOL WOL WOL WOL WOL RTEE RTEE TEE
12 WOL WOL WOL WOL WOL RTEE RTEE RTEE TEE RTEE - Red Tee
14 WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE TEE
16 WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE TEE
18 WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE TEE HC - Half Coupling
20 WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
24 WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
26 WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE SOC - Sockolet
28 WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28
BRANCH SIZE
Notes
50 Piping, fittings and acessories shall be organic coated internally according to I-ET-3010.00-1200-956-P4X-002 - General Painting.
151 Pipe NPS 2 and smaller shall be used only for short-length branch connections, w here the coating aplication is feasible.
P 4X-001

F - Safety System and Flare; PC - Process (Corrosive Hydrocarbon); PC W - Produced water;
Super 150 B12
Duplex
Te mp e rature (°C) 0 38 50 100 120 140
Max Pre ssure (b arg ) 20 20 19.5 17.7 16.9 16.1
½" - 1 ½" PE
T-303 ASTM A790 (UNS S32760) SML
Pipes
2" - 8" S-40S

Pipe - ASME B36.10/B36.19
10" - 24" BE
T-304 ASTM A928 (UNS S32760 Cl 1 or 3) WLD
26" - 36" 0.375"
90 Elbow C01-30
45 Elbow C02-30
Tee C03-30
ASME B16.11
Cross C05-30 ½" - 1 ½"
ASTM A182 Gr F55 (UNS S32760)
Cap C11-30
Red Tee C04-30
¾" - 1 ½" ASME B16.11
Red Coupling C08-30
Fittings

90 LR Elbow C15-32
45 LR Elbow C16-32
90 SR Elbow C17-32
2" - 36"
Tee C20-32
Cap C22-32 ASME B16.9 ASTM A815 (UNS S32760)
Cross C24-32
Conc. Red C18-32
Ecc. Red C19-32 3" - 36"
Red Tee C21-32
Straight Nipple N-S131 ½" - 1 ½" ASTM A733 ASTM A790 (UNS S32760)
PBE
N-C132 ¾" - 1 ½"
Nipple
Swage Conc Nipple

MSS SP-95 ASTM A815 (UNS S32760)
N-E132 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E432 2" - 4" BLE x PSE
Socket Weld (SW) F-150-JH ½" - 1 ½"
ASME B16.5
Flanges
2" - 24"
Welding Neck (WN) F-150-KH
26" - 36" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A182 Gr F55
½" - 24" ASME B16.5
Blind F-150-LH
26" - 36" ASME B16.47 A
Nuts Gasket
Spiral-Wound J-150-EL ½" - 36" - Class 150 Raised Face ASME B16.20 Duplex/graphite
A320 L7, Zn-Ni

Paddles Stud &

A194 7L, Zn-Ni
Figure-8 Blank R8-150-RX ½" - 14"
Paddle Blank RA-150-RX According to pipe 150 Raised Face ASME - Superduplex ASTM A240 UNS32760
16" - 36" B16.5
Paddle Spacer RE-150-RX
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Super 150 B12
Duplex
Valv es (see notes)
VAG-3000-1-D302 VES-801-3-D305 VES-150-3-D337 VDE-150-2-D3F1
Needle ½" - 1 ½" -46C to 150C ½" - 1 ½" 0C to 150C -30C to 150C
VAG-3000-1-D3F2 VES-801-3-D3F5 VES-150-3-D33G Double ½" - 2" VDE-150-2-D3F2
6" - 20" VBO-150-2-D311 VES-150-1-D310 -30C to 150C VES-150-3-D352 Ball VDE-150-2-D3F3
0C to 150C -46C to 150C
24" - 32" VBO-150-2-D313 VES-150-1-D330 0C to 150C VES-150-3-D353 VDE-150-2-D3F4
Butterfly Ball 2" - 36" 0C to 150C
10" - 20" VBO-150-3-D361 VES-150-2-D310 VES-150-3-D35G ½" - 1 ½" VGA-801-1-D301
-46C to 150C Gate -50C to 150C
24" - 32" VBO-150-3-D363 VES-150-2-D31F -30C to 150C VES-150-3-D372 2" - 36" VGA-150-1-D331
Ball
VES-801-1-D301 VES-150-2-D31G VES-150-3-D373 VGL-150-1-D301
2" - 36" Globe 2" - 18" -46C to 150C
VES-801-1-D305 VES-150-2-D330 VES-150-3-D37G VGL-150-2-D3F1
0C to 150C
VES-801-2-D301 VES-150-2-D33F 0C to 150C VDE-150-2-D301 Plug 2" - 24" VMA-150-2-D301 0C to 110C
Ball ½" - 1 ½" -30C to 150C
VES-801-2-D305 VES-150-2-D33G Double VDE-150-2-D302 ½" - 1 ½" VRE-800-1-D302
VES-801-2-D3F1 -30C to 150C VES-150-3-D317 Ball ½" - 2" VDE-150-2-D303 Check VRE-150-2-D315 -46C to 150C
-30C to 150C -46C to 150C 2" - 32"
VES-801-2-D3F5 0C to 150C VES-150-3-D31G VDE-150-2-D304 VRE-150-2-D335
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
BRANCH SIZE
Notes
26 See Annex A for v alv e casting qualification requirements.
48 Superduplex ex ternal coating shall be applied for the temperature limits according to I-ET-3010.00-1200-956-P4X-002 - General Painting.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
123 The application of this pipe specification for PCW - Produced Water is conditioned to max imum ox y gen content 20 ppb and max temperature 120ºC.
P 4X-001

C N - Sodium Hypochlorite; D A - Open Drain; IW - De-Aerated Sea Water Injection; IW C - Aerated Sea Water Injection; SW - Aerated Sea Water;
Organic 150 B14
Coat CS
Te mp e rature (°C) 0 38 50 70 80
2" - 6" STD
Pipes
SAW)
Pipe T-102 14" - ASME B36.10
BE
16" - 24" S-10 API 5L Gr B PSL 1 WLD (HFW or SAW)
26" - 30"
32" - 44" STD
90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
1" - 44"
Fittings
Tee C20-03
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 1 ½" - 42"
Red Tee C21-03
1" - 24" ASME B16.5
Welding Neck (WN) F-150-D2
26" - 44" ASME B16.47 A
According to pipe Class 150 Flat Face ASTM A105
1" - 24" ASME B16.5
Blind F-150-E2
26" - 44" ASME B16.47 A
Flat type J-150-CC 1" - 44" - Class 150 Flat Face ASME B16.21 Multidirectional Expanded PTFE
A193 B7, Zn-Ni

Paddles Stud &
Stud and Nuts P-150-07 1" - 1 ½" - - - ASME B1.1

A194 Gr 2H, Zn-Ni
Figure-8 Blank R8-150-FP 1" - 14"
Paddle Blank RA-150-FP According to pipe 150 Flat Face ASME - Carbon Steel ASTM A516 GR60 epoxi coated
16" - 44" B16.5
Paddle Spacer RE-150-FP
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Organic 150 B14
Coat CS
Valv es (see notes)
Needle 1" - 1 ½" VAG-150-1-D301 -50C to 150C Butterfly 24" - 32" VBO-150-3-U366 -29C to 75C Ball 1" - 6" VES-150-2-U600 0C to 70C Globe 2" - 12" VGL-150-2-U302 0C to 90C
2" - 20" VBO-250-1-U204 VES-150-1-U300 1" - 3" VGA-150-1-U102 -29C to 75C VRE-150-1-U305 0C to 90C
0C to 75C 1" - 1 ½" 1" - 1 ½"
24" - 32" VBO-250-1-U206 VES-150-2-U300 Gate VGA-150-1-U332 VRE-150-2-D305 -46C to 150C
1" - 24" 0C to 90C
Butterfly 6" - 20" VBO-150-2-U314 Ball VES-150-1-U310 0C to 90C VGA-150-2-U332 Check 2" - 32" VRE-150-1-U314
0C to 90C 0C to 90C
24" - 32" VBO-150-2-U316 2" - 4" VES-150-1-U316 2" - 12" VGL-150-1-U302 4" - 32" VRE-150-2-U335
Globe 0C to 90C
6" - 20" VBO-150-3-U364 -29C to 75C VES-150-2-U310 1" - 1 ½" VGL-150-1-U303 2" - 6" VRE-150-2-U666 0C to 70C
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
26 WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE SOC - Sockolet
28 WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE TEE
30 WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE TEE
32 WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
34 WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
36 WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
38 WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
40 WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
42 WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
44 WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36 38 40 42 44
BRANCH SIZE
Notes
28 The IW serv ice is only applicable for offshore units.
137 For Sodium Hy pochlorite (CN) serv ice only shall be applied the follow ing v alv es: VRE-150-2-U655; VRE-150-2-D305; VAG-150-1-D301; VES-150-2-U600; VES-150-3-D300.
151 Pipe NPS 2 and smaller shall be used only for short-length branch connections, w here the coating aplication is feasible.
P 4X-001

AM - Amine; F - Safety System and Flare; PC - Process (Corrosive Hydrocarbon); PC W - Produced water;
Duplex 150 B16
Te mp e rature (°C) -46 0 38 50 100 130
Max Pre ssure (b arg ) 20 20 20 19.5 17.7 16.5
½" - 1 ½" PE
Pipes
2" - 8" S-40S

10" - 24" BE
26" - 40" 0.375"
90 Elbow C01-27
45 Elbow C02-27
Tee C03-27
ASME B16.11
Cross C05-27 ½" - 1 ½"
Cap C11-27
Red Tee C04-27
¾" - 1 ½" ASME B16.11
Red Coupling C08-27
Fittings

90 LR Elbow C15-29
45 LR Elbow C16-29
90 SR Elbow C17-29
2" - 40"
Tee C20-29
Cross C24-29
Conc. Red C18-29
Ecc. Red C19-29 3" - 40"
Red Tee C21-29
PBE
N-C129 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E129 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E429 2" - 4" BLE x PSE
Socket Weld (SW) F-150-JG ½" - 1 ½"
ASME B16.5
Flanges
2" - 24"
Welding Neck (WN) F-150-KG
½" - 24" ASME B16.5
Blind F-150-LG
26" - 40" ASME B16.47 A
Nuts Gasket
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
Figure-8 Blank R8-150-RD ½" - 14"
Paddle Blank RA-150-RD According to pipe 150 Raised Face ASME - Duplex Stainless Steel ASTM A240 UNS31803
16" - 40" B16.5
Paddle Spacer RE-150-RD
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Duplex 150 B16
Valv es (see notes)
VAG-3000-1-D202 VES-150-1-D210 -30C to 150C VES-150-3-D227 0C to 150C VDE-150-2-D2F1
Needle ½" - 1 ½" -46C to 150C -30C to 150C
VAG-3000-1-D2F2 VES-150-1-D220 0C to 150C 2" - 36" VES-150-3-D236 Double 1" - 2" VDE-150-2-D2F2
6" - 20" VBO-150-2-D211 -46C to 150C 2" - 36" VES-150-1-D230 -46C to 150C VES-150-3-D237 -46C to 150C Ball VDE-150-2-D2F3
-46C to 150C
24" - 32" VBO-150-2-D213 -46C to 200C VES-150-2-D210 2" - 28" VES-150-3-D23G VDE-150-2-D2F4
Butterfly
6" - 20" VBO-150-3-D261 VES-150-2-D216 VES-150-3-D252 ½" - 1 ½" VGA-801-1-D201
-46C to 150C -30C to 150C 2" - 36"
24" - 32" VBO-150-3-D263 VES-150-2-D21F VES-150-3-D253 -30C to 150C Gate VGA-150-1-D231 -50C to 150C
2" - 28" Ball 2" - 36"
VES-801-1-D201 -30C to 150C VES-150-2-D21G 2" - 28" VES-150-3-D25G VGA-150-2-D231
VES-801-1-D202 VES-150-2-D220 VES-150-3-D262 VGL-150-1-D201
-46C to 150C 0C to 150C 0C to 150C
VES-801-1-D205 Ball VES-150-2-D226 VES-150-3-D263 Globe 2" - 18" VGL-150-2-D201 -46C to 150C
2" - 36" 2" - 36"
VES-801-2-D201 -30C to 150C VES-150-2-D230 VES-150-3-D272 VGL-150-2-D2F1
VES-801-2-D202 VES-150-2-D236 VES-150-3-D273 -46C to 150C VRE-800-1-D202
-46C to 150C -46C to 150C ½" - 1 ½" -46C to 150C
Ball ½" - 1 ½" VES-801-2-D205 VES-150-2-D23F 2" - 28" VES-150-3-D27G VRE-800-2-D202
2" - 28"
VES-801-2-D2F1 -30C to 150C VES-150-2-D23G VDE-150-2-D201 VRE-150-1-D211 0C to 150C
-30C to 150C Check
VES-801-2-D2F2 VES-150-3-D216 Double VDE-150-2-D202 VRE-150-2-D212
2" - 36"
VES-801-2-D2F5 VES-150-3-D217 -30C to 150C Ball ½" - 2" VDE-150-2-D203
2" - 32"
VRE-150-2-D215 -46C to 150C
-46C to 150C -46C to 150C
VES-801-3-D205 2" - 28" VES-150-3-D21G VDE-150-2-D204 VRE-150-2-D235
VES-801-3-D2F5 2" - 36" VES-150-3-D226 0C to 150C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36 38 40
BRANCH SIZE
Notes
29 Duplex stainless steell ex ternal coating shall be applied for the temperature limits according to I-ET-3010.00-1200-956-P4X-002 - General Painting.
60 This spec for Amine serv ice is applicable for piping upstream the Amine Regeneration unit.
P 4X-001

PC - Process (Corrosive Hydrocarbon);
Carbon 150 B17
Steel
Te mp e rature (°C) 0 38 50 100 120
¾" - 1 ½" XXS PE API 5L Gr B PSL 1 SML
2" - 3" S-160
4" XS
Pipes
Pipe T-102 6" 0.344" - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
BE SAW)
8" S-60
10" 0.438"
12" - 14" S-40
Sockolet C55-02 ½" - 1 ½" MSS SP-97
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
¾" - 1 ½"
Cross C05-02 - 9000 SW
ASME B16.11 ASTM A105
Coupling C06-02
Cap C11-02
Red Tee C04-02
1" - 1 ½"
Red Coupling C08-02
Fittings

90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
2" - 14"
Tee C20-03
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 14"
Red Tee C21-03
Straight Nipple N-S120 ¾" - 1 ½" ASTM A733 API 5L Gr B PSL 1 seamless
PBE
N-C103 1 ½"
Nipple
Swage Conc Nipple

N-E103 1 ½" PBE
Swage Ecc Nipple
N-E403 2" - 4" BLE x PSE
Stud & Gasket Flanges
Socket Weld (SW) F-150-J2 ¾" - 1 ½"

Blind F-150-L2 ¾" - 14"
Spiral-Wound J-150-EH ¾" - 14" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
A193 B7, Zn-Ni

Nuts
Stud and Nuts P-150-07 ¾" - 1" - - - ASME B1.1

A194 Gr 2H, Zn-Ni
P 4X-001
Steel
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-150-2-C111 VES-150-3-C11G -29C to 150C VDE-150-2-C1F6 -29C to 200C
VAG-3000-1-S202 -100C to 400C VES-150-2-C116 VES-150-3-C136 Double ¾" - 2" VDE-150-2-C1F7
Needle ¾" - 1 ½" Ball -29C to 340C
0C to 150C
VAG-3000-1-S2F2 -100C to 400C VES-150-2-C130 0C to 150C VES-150-3-C13G 3" - 8" VDE-150-2-C11F -29C to 150C
VES-804-1-C101 0C to 150C VES-150-2-C136 VES-150-3-C152 ¾" - 1 ½" VGA-801-1-C101
VES-804-1-C105 -29C to 210C VES-150-2-C13F VES-150-3-C153 -29C to 150C Gate VGA-150-1-C131 -29C to 400C
Ball 2" - 14" 2" - 14"
VES-804-2-C101 0C to 150C VES-150-2-C13G VES-150-3-C172 VGA-150-2-C131
¾" - 1 ½" VES-804-2-C105 Ball 2" - 14" VES-150-2-C150 -29C to 150C VES-150-3-C173 0C to 210C VGL-150-1-C101
VES-804-2-C1F5 VES-150-2-C152 0C to 150C VES-150-3-C17G VGL-150-2-C101
-29C to 210C Globe 2" - 14" -29C to 400C
VES-804-3-C105 VES-150-2-C170 VES-150-3-C18G -29C to 400C VGL-150-2-C1F1
Ball
VES-804-3-C1F5 VES-150-2-C172 VES-150-4-C154 0C to 150C VGL-150-2-C1F2
0C to 210C
VES-150-1-C110 -29C to 150C VES-150-2-C17F VES-150-4-C174 0C to 210C VRE-150-1-C111 0C to 150C
VES-150-1-C130 VES-150-2-C17G VDE-150-2-C1F1 2" - 14" VRE-150-2-C112
0C to 150C Double ¾" - 2" -29C to 150C Check -29C to 400C
2" - 14" VES-150-1-C150 VES-150-2-C18G 0C to 400C
Ball VDE-150-2-C1F2 VRE-150-2-C115
VES-150-1-C170 0C to 210C VES-150-3-C116 -29C to 150C VDE-150-2-C1F5 -29C to 200C - VRE-150-2-C135 -29C to 210C
VES-150-2-C110 -29C to 150C
Branch (see notes)
0.75 TEE
1 RTEE TEE
1.5 RTEE RTEE TEE WOL - Weldolet
2 SOC SOC SOC TEE
3 SOC SOC SOC RTEE TEE
4 SOC SOC SOC RTEE RTEE TEE TEE - Tee
6 SOC SOC SOC WOL RTEE RTEE TEE
8 SOC SOC SOC WOL WOL RTEE RTEE TEE
10 SOC SOC SOC WOL WOL WOL RTEE RTEE TEE RTEE - Red Tee
12 SOC SOC SOC WOL WOL WOL RTEE RTEE RTEE TEE
14 SOC SOC SOC WOL WOL WOL WOL RTEE RTEE RTEE TEE
0.75 1 1.5 2 3 4 6 8 10 12 14 HC - Half Coupling
BRANCH SIZE
SOC - Sockolet
Notes
P 4X-001

F - Safety System and Flare; F G - Fuel Gas; PC - Process (Corrosive Hydrocarbon);
Low T emp 150 B19
CS
Te mp e rature (°C) -46 0 38 50 100 150 200 210
½" - 1 ½" S-160 PE
2" XS
3" - 6" STD
8" - 12" S-20
16" S-10
Pipes
18" - 20" 0.281"

Pipe - ASME B36.10
24" 0.312" BE
26" - 28" 0.344"
30" - 32" STD
34" - 38" 0.406"
40" - 42" 0.438"
44" 0.469"
90 Elbow C01-04
45 Elbow C02-04
Tee C03-04
ASME B16.11
Cross C05-04 ½" - 1 ½"
Cap C11-04
Red Tee C04-04
¾" - 1 ½" ASME B16.11
Red Coupling C08-04
Fittings

90 LR Elbow C15-05
45 LR Elbow C16-05
90 SR Elbow C17-05
2" - 40"
Tee C20-05
Cross C24-05
Red Tee C21-05 3" - 40"
Conc. Red C18-05
3" - 44"
Ecc. Red C19-05
PBE
N-C105 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E105 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E405 2" - 4" BLE x PSE
Socket Weld (SW) F-150-J3
½" - 1 ½"
ASME B16.5
Flanges
2" - 24"
½" - 24" ASME B16.5
Blind F-150-L3
26" - 40" ASME B16.47 A
Nuts Gasket
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
16" - 44" B16.5
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Low T emp 150 B19
CS
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-803-3-C2F2 -46C to 150C VES-150-2-C280 VDE-150-2-C206 -46C to 200C
½" - 1 ½"
VAG-3000-1-S202 -100C to 400C VES-803-3-C2F5 -46C to 200C VES-150-2-C282 -46C to 345C VDE-150-2-C207
Needle ½" - 1 ½" -46C to 340C
VAG-3000-1-S2F1 -100C to 200C VES-150-1-C210 -30C to 150C VES-150-2-C28G VDE-150-2-C208
VAG-3000-1-S2F2 -100C to 400C VES-150-1-C230 -46C to 150C VES-150-3-C216 VDE-150-2-C2F1
-30C to 150C
6" - 20" VBO-150-2-C211 VES-150-1-C250 -30C to 150C VES-150-3-C217 -30C to 150C VDE-150-2-C2F2
-46C to 200C
24" - 32" VBO-150-2-C213 VES-150-1-C270 -46C to 200C VES-150-3-C21G ½" - 2" VDE-150-2-C2F3
Double -46C to 150C
6" - 20" VBO-150-2-C231 VES-150-1-C280 -46C to 345C VES-150-3-C236 Ball VDE-150-2-C2F4
-46C to 250C
24" - 32" VBO-150-2-C233 VES-150-2-C210 VES-150-3-C237 -46C to 150C VDE-150-2-C2F5
Butterfly -46C to 200C
VBO-150-3-C221 VES-150-2-C216 VES-150-3-C23G VDE-150-2-C2F6
-30C to 150C Ball 2" - 36"
VBO-150-3-C223 VES-150-2-C21F VES-150-3-C252 VDE-150-2-C2F7
- -46C to 240C -30C to 150C -46C to 340C
VBO-150-3-C261 VES-150-2-C21G VES-150-3-C253 VDE-150-2-C2F8
VBO-150-3-C263 Ball VES-150-2-C230 VES-150-3-C25G -29C to 150C VDE-150-2-C215
3" - 8" -30C to 150C
VES-803-1-C201 -30C to 150C 2" - 36" VES-150-2-C236 VES-150-3-C272 VDE-150-2-C21F
-46C to 150C
VES-803-1-C205 -30C to 200C VES-150-2-C23F VES-150-3-C273 -46C to 200C Gate ½" - 1 ½" VGA-801-2-C201 -46C to 240C
VES-803-2-C201 -30C to 150C VES-150-2-C23G VES-150-3-C27G VGL-150-1-C201
VES-803-2-C202 -46C to 150C VES-150-2-C250 VES-150-3-C282 Globe 2" - 18" VGL-150-2-C201 -46C to 345C
VES-803-2-C205 -46C to 200C VES-150-2-C252 VES-150-3-C283 -46C to 345C VGL-150-2-C2F1
-30C to 150C
Ball ½" - 1 ½" VES-803-2-C206 -46C to 240C VES-150-2-C25F VES-150-3-C28G VRE-800-1-C202
½" - 1 ½" -46C to 345C
VES-803-2-C2F1 -30C to 150C VES-150-2-C25G VDE-150-2-C201 VRE-800-2-C202
-30C to 150C
VES-803-2-C2F2 -46C to 150C VES-150-2-C270 VDE-150-2-C202 VRE-150-1-C211 0C to 345C
Double ½" - 2" Check
VES-803-2-C2F5 VES-150-2-C272 Ball VDE-150-2-C203 2" - 32" VRE-150-2-C212
-46C to 200C -46C to 200C -46C to 150C -46C to 345C
VES-803-3-C205 VES-150-2-C27F VDE-150-2-C204 VRE-150-2-C215
VES-803-3-C2F1 -30C to 150C VES-150-2-C27G VDE-150-2-C205 -46C to 200C 1" - 32" VRE-150-2-C235 -46C to 210C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36 38 40 42 44
BRANCH SIZE
Notes
P 4X-001

D A - Open Drain; H W U - Utility Heating Water; IW - De-Aerated Sea Water Injection; IW C - Aerated Sea Water Injection; PW H - Hot Fresh Water; SW - Aerated Sea Water; W -
F RP 10 bar B22
Industrial water;

Te mp e rature (°C) 15 90
Max Pre ssure (b arg ) 10 10
Bell-Spigot
1" - 36"
Butt-Strap
FRP - Bisphenol A Epoxy resins reinforced with
Pipes
Bell-Spigot
Pipe T-404 38" acc. manufact. - ISO 14692 fiberglass type E or E-CR. Design pressure 10
Butt-Strap bar@90ºC. SML
Bell-Spigot
40" - 48"
Butt-Strap
Plug C09-36 250 THD ASME B16.15 ASTM B62 (UNS C83600)
1" - 1 ½"
Thd Saddle C52-52 -
- -
Flg Saddle C51-52 1" - 6"
Butt-Strap
Tee C20-52 1" - 40"
BellSpigot
Butt-Strap
90 LR Elbow C15-52 According to pipe
BellSpigot
Fittings
1" - 44" FRP - Bisphenol A Epoxy resins reinforced with

Butt-Strap
45 LR Elbow C16-52 ISO 14692 fiberglass type E or E-CR. Design pressure
BellSpigot 10bar@90ºC
10 bar
Butt-Strap
FRP Conc. Red. C61-52
BellSpigot
Butt-Strap
FRP Ecc. Red. C62-52 2" - 40" -
BellSpigot
Butt-Strap
Red Tee C63-52
BellSpigot
Stud & GasketFlanges
Blind F-10-ET
1" - 40" According to pipe 10 bar Flat Face ASTM D4024 - Drilling acc. FRP - Bisphenol A Epoxy resins reinforced with
Integral Flange F-10-1T B16.5/B16.47 CL150 fiberglass type E or E-CR. Suitable for 90°C.
Flat type J-150-C3 1" - 40" - Class 150 Flat Face ASME B16.21 Neoprene
A193 B7, Zn-Ni

Nuts

A194 Gr 2H, Zn-Ni
Figure-8 Blank R8-150-FP1" - 14"
16" - 36"
Paddles
Paddle Blank RA-150-FP 38"

40" According to pipe 150 Flat Face ASME - Carbon Steel ASTM A516 GR60 epoxi coated
B16.5
16" - 36"
Paddle Spacer RE-150-FP 38"
40"
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S F RP 10 bar B22
Valv es (see notes)
6" - 20" VBO-150-1-U204 Butterfly 24" - 36" VBO-150-3-U366 -29C to 75C VGA-150-1-U332 Check 2" - 24" VRE-150-1-U314 0C to 90C
0C to 75C Gate 1" - 12" 0C to 90C
24" - 36" VBO-150-1-U206 2" - 24" VES-150-1-U310 VGA-150-2-U332 4" - 10" VES-150-1-U403
Butterfly 6" - 20" VBO-150-2-U314 Ball 2" VES-150-1-U316 0C to 90C VGL-150-1-U302 Ball 2" - 3" VES-250-1-U403 10C to 70C
0C to 90C Globe 2" - 18" 0C to 90C
24" - 36" VBO-150-2-U316 2" - 24" VES-150-2-U310 VGL-150-2-U302 1" - 1 ½" VES-275-1-U403
6" - 20" VBO-150-3-U364 -29C to 75C
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 FSDL RTEE RTEE RTEE TEE
4 FSDL FSDL RTEE RTEE RTEE TEE TEE - Tee
6 FSDL FSDL FSDL FSDL RTEE RTEE TEE
8 FSDL FSDL FSDL FSDL FSDL RTEE RTEE TEE
10 FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE TEE RTEE - Red Tee
12 FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE TEE
14 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE TEE
16 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE TEE HC - Half Coupling
18 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE TEE
20 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE TEE
24 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE SOC - Sockolet
26 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
28 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
30 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE FSDL - Flg Saddle
32 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
36 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
38 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE TSDL - Thd Saddle
40 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
42 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
44 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
46 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
48 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
1 1.5 2 2.5 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 36 38 40 42 44 46 48
BRANCH SIZE
Notes
31 Electrical conductiv ity /resistiv ity shall be tested in accordance w ith ASTM D257. For components requiring electrical conductiv ity due to ex ternal charge generating mechanisms, the surface
resistiv ity shall be 10^5 ohms or less. For components requiring electrical conductiv ity due to internal charge generating mechanisms, the v olume resistiv ity shall be 10^3 ohm-meter or less.
32 GRP piping and fittings must be certified according to lev el L3 IMO A753 fire endurance test.
33 GRP piping and fittings must be supplied w ith UV protection.
34 GRP piping and fittings must hav e Ty pe Approv al certified by Classification Societies.
35 Pipes and fittings must be supplied by the same manufacturer, that also shall be responsable for design, fabrication, assembly , inspection, test, repair and comissioning.
36 Plain w ashers must be used to assembly flanged connections.
37 See Annex H for Minimum Requirements for FRP pipes and fittings.
39 The bolt torque limit shall be informed by manufacturer.
74 Bell-spigot adhesiv ed joint is allow able for all diameter in open drain (DA) serv ice, but the max imum pressure shall be 4 bar.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
112 For pipes and fittings may be used as alternativ e v iny l ester resins. See Annex H.
149 It shall be used internal electrical conductiv ity liner (C-glass, single v eil) for pipes and fittings
P 4X-001

AD W - Aerated Dilution Water; D A - Open Drain; H W U - Utility Heating Water; IW - De-Aerated Sea Water Injection; IW C - Aerated Sea Water Injection; PW H - Hot Fresh Water;
F RP 16 bar B23
SW - Aerated Sea Water; W - Industrial water;

1" - 48" Bell-Spigot
FRP - Bisphenol A Epoxy resins reinforced with
Pipes
1" - 56"
Pipe T-406 acc. manufact. - ISO 14692 fiberglass type E or E-CR. Design pressure 16
60" Butt-Strap bar@90ºC. SML
64"
1" - 1 ½"
Thd Saddle C52-54
- - -
Coupling C06-54
90 LR Elbow C15-54 BellSpigot
45 LR Elbow C16-54
According to pipe
1" - 48" Butt-Strap
Tee C20-54
BellSpigot
Fittings
Butt-Strap FRP - Bisphenol A Epoxy resins reinforced with

FRP Stub End C64-54 -
BellSpigot ISO 14692 fiberglass type E or E-CR. Design pressure
45 LR Elbow C16-54 1" - 60" 16 bar 16bar@90ºC
According to pipe Butt-Strap
90 LR Elbow C15-54 1" - 64"
BellSpigot
FRP Ecc. Red. C62-54
2" - 48"
Butt-Strap
Red Tee C63-54 -
BellSpigot
2" - 64" Butt-Strap
ASTM D4024 - Drilling acc. FRP - Bisphenol A Epoxy resins reinforced with
Blind F-16-LT 1" - 48" B16.5/B16.47 CL150 fiberglass type E or E-CR. Suitable for 90°C.
1" - 2" According to pipe 16 bar Raised Face Drilling acc. B16.5/B16.47
Backing Flange F-16-YV CL150 ASTM A105 Epoxy coated
3" - 48"
Flat type J-150-P3 1" - 48" - Class 150 Raised Face ASME B16.21 Neoprene
A193 B7, Zn-Ni

Nuts

A194 Gr 2H, Zn-Ni
1" - 2"
Figure-8 Blank R8-150-RP
3" - 14"
16" - 56"
Paddles
Paddle Blank RA-150-RP 60" Raised Face ASME

According to pipe 150 B16.5 - Carbon Steel ASTM A516 GR60 epoxi coated
64"
16" - 56"
Paddle Spacer RE-150-RP 60"
64"
P 4X-001
Valv es (see notes)
6" - 20" VBO-250-1-U291 Butterfly 24" - 32" VBO-150-3-U363 -29C to 75C VGA-150-1-U332 VRE-150-1-U312
0C to 75C Gate 1" - 12" 0C to 90C 2" - 48"
24" - 46" VBO-250-1-U293 VES-150-1-U300 VGA-150-2-U332 Check VRE-150-1-U314 0C to 90C
1" - 1 ½"
6" - 20" VBO-150-2-U311 VES-150-2-U300 2" - 24" VGL-150-1-U302 4" - 40" VRE-150-2-U335
Butterfly 24" - 44" VBO-150-2-U313 2" - 24" VES-150-1-U310 Globe 1" - 1 ½" VGL-150-1-U303 0C to 90C 4" - 6" VES-150-1-U403
0C to 90C Ball 0C to 90C
6" - 20" VBO-150-2-U351 2" VES-150-1-U316 2" - 24" VGL-150-2-U302 Ball 2" - 3" VES-250-1-U403 10C to 70C
24" - 44" VBO-150-2-U353 VES-150-1-U350 VRE-150-1-U305 0C to 90C 1" - 1 ½" VES-275-1-U403
2" - 4" Check 1" - 1 ½"
6" - 20" VBO-150-3-U361 -29C to 75C VES-150-2-U310 VRE-150-2-D305 -46C to 150C
Branch (see notes)
1 TEE
1.5 RTEE TEE
42 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
44 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
46 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
48 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
52 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
56 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
60 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
64 FSDL FSDL FSDL FSDL FSDL FSDL FSDL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
1 1.5 2 2.5 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 36 40 42 44 46 48 52 56 60 64
BRANCH SIZE
Notes
P 4X-001

PC W - Produced water;
F RP 16 bar B26
Bell-Spigot FRP - Bisphenol A Epoxy resins reinforced with
Pipes
Pipe T-408 1" - 36" acc. manufact. - ISO 14692 fiberglass type E or E-CR. Design pressure 16
Butt-Strap bar@120ºC. SML
1" - 1 ½"
Thd Saddle C52-56 -
- -
90 LR Elbow C15-56
45 LR Elbow C16-56 According to pipe
Fittings

Tee C20-56 1" - 36"
ISO 14692 fiberglass type E or E-CR. Design pressure
FRP Stub End C64-56 16 bar 16bar@120ºC
BellSpigot
FRP Conc. Red. C61-56 -
FRP Ecc. Red. C62-56 2" - 36" Butt-Strap
Red Tee C63-56
Nuts Gasket Flanges
Blind F-16-EU Flat Face B16.5/B16.47 CL150 fiberglass type E or E-CR. Suitable for 120°C.
1" - 36" According to pipe 16 bar
Backing Flange F-16-YV Raised Face Drilling acc. B16.5/B16.47 ASTM A105 Epoxy coated
CL150
A193 B7, Zn-Ni

Paddles Stud &
Stud and Nuts P-150-07 ½" - 1" - - - ASME B1.1

A194 Gr 2H, Zn-Ni
16" - 36" B16.5
P 4X-001
Valv es (see notes)
6" - 20" VBO-150-2-D111 VES-150-1-D210 Ball 2" - 28" VES-150-3-D226 0C to 150C 2" - 12" VRE-150-1-D111
-29C to 150C 0C to 150C
24" - 36" VBO-150-2-D113 VES-150-1-D216 Double 1" - 2" VDE-150-1-D201 -30C to 150C VRE-150-1-D114
Butterfly Ball Check
6" - 20" VBO-150-2-D251 VES-150-2-D110 -30C to 150C 2" - 28" VRE-150-1-D212
-46C to 150C VGA-150-1-D231 -46C to 150C
24" - 36" VBO-150-2-D253 Ball 2" - 28" VES-150-2-D210 Gate 2" - 28" -50C to 150C VRE-150-2-D235
VGA-150-2-D231
VES-150-1-D200 VES-150-2-D216 VGL-150-1-D201 -46C to 150C
4" - 10" VES-150-1-U404
1" - 1 ½"
Ball VES-150-2-D200 -30C to 150C VES-150-2-D230 -46C to 150C Ball 2" - 3" VES-250-1-U404 10C to 90C
Globe 2" - 18" VGL-150-2-D101 0C to 150C
2" - 28" VES-150-1-D110 VES-150-3-D216 -30C to 150C
VGL-150-2-D201 -46C to 150C
1" - 1 ½" VES-275-1-U404
Branch (see notes)
1 TEE
1.5 RTEE TEE
1 1.5 2 2.5 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 36 40
BRANCH SIZE
Notes
66 It´s not allow ed to use ov erw rap joints (adhesiv e joint cov ered by fiber-resin lay ers).
P 4X-001

C I2 - DBNPA Biocide; C N - Sodium Hypochlorite;
F RP 16 bar B27
Butt-Strap FRP - Epoxy vinylester resins (bisphenol A
Pipes
Pipe T-409 1" - 6" acc. manufact. - ISO 14692 brominated) reinforced with fiberglass type E-CR,
Bell-Spigot inner liner with fiberglass veils type C. Design
pressure 16 bar@85ºC. SML
Thd Saddle C52-57 1" - 1 ½"
- - -
90 LR Elbow C15-57 FRP - Epoxy vinylester resins (bisphenol A or
Fittings
45 LR Elbow C16-57 1" - 6" According to pipe brominated) reinforced with fiberglass type E-CR,
ISO 14692 inner liner with fiberglass veils type C. Design
Tee C20-57
16 bar Butt-Strap pressure 16bar@85ºC
Red Tee C63-57 2" - 3"
FRP Conc. Red. C61-57 -
2" - 6"
Nuts GasketFlanges
Blind F-16-ES FRP - Epoxy vinylester resins (bisphenol A or

1" - 6" According to pipe 16 bar Flat Face ASTM D4024 - Drilling acc. brominated) reinforced with fiberglass type E-CR.
Integral Flange F-16-1S B16.5/B16.47 CL150 Suitable for 85°C.
Flat type J-150-CC 1" - 6" - Class 150 Flat Face ASME B16.21 Multidirectional Expanded PTFE
A193 B7, Zn-Ni

Paddles Stud &
Stud and Nuts P-150-07 ½" - ¾" - - - ASME B1.1

A194 Gr 2H, Zn-Ni
Figure-8 Blank R8-150-FP 1" - 6" According to pipe 150 Flat Face ASME - Carbon Steel ASTM A516 GR60 epoxi coated
B16.5
P 4X-001
Valv es (see notes)
Ball 1" - 2" VES-150-2-U600 0C to 70C Check 2" VRE-150-2-U666 0C to 70C
Branch (see notes)
1 TEE
1.5 RTEE TEE
4 FSDL FSDL FSDL FSDL FSDL TEE TEE - Tee
6 FSDL FSDL FSDL FSDL FSDL FSDL TEE
1 1.5 2 2.5 3 4 6
BRANCH SIZE RTEE - Red Tee
HC - Half Coupling
SOC - Sockolet
FSDL - Flg Saddle
TSDL - Thd Saddle
Notes
66 It´s not allow ed to use ov erw rap joints (adhesiv e joint cov ered by fiber-resin lay ers).
P 4X-001

F - Safety System and Flare; IW - De-Aerated Sea Water Injection; PC - Process (Corrosive Hydrocarbon);
CS Inconel 150 B30
Clad.
Te mp e rature (°C) 0 38 50 100 150 200 240
½" - 1 ½" PE
T-203 S-40S ASME B36.10/B36.19 ASTM B444 Gr 1 (UNS N06625) SML
2" - 3"
4" - 6" STD
SAW)
Pipes
14"
Pipe S-10 -
16" - 18" BE
T-102 ASME B36.10
24" 0.312"
26" - 28" S-10
30" 0.344"
90 Elbow C01-33
45 Elbow C02-33
Tee C03-33
ASME B16.11
Cross C05-33 ½" - 1 ½"
Cap C11-33
Red Tee C04-33
¾" - 1 ½" ASME B16.11 ASTM B366 (UNS N06625)
Red Coupling C08-33
90 LR Elbow C15-33
45 LR Elbow C16-33
90 SR Elbow C17-33
2" - 3" ASME B16.9
Tee C20-33
Cap C22-33
Fittings
Cross C24-33
C12-33 2" - 4"
Weldolet MSS SP-97
C12-02 2" - 14" ASTM A105
Conc. Red C18-33
Ecc. Red C19-33 3" - 4" ASTM B366 (UNS N06625)
Red Tee C21-33
90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
4" - 30" ASME B16.9
Tee C20-03
Cap C22-03 ASTM A234 Gr WPB
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 6" - 30"
Red Tee C21-03
Straight Nipple N-S139 ½" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
PBE
N-C133 ¾" - 1 ½"
Nipple
Swage Conc Nipple

MSS SP-95 ASTM B366 (UNS N06625)
N-E133 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E433 2" - 4" BLE x PSE
Socket Weld (SW) F-150-JL ½" - 1 ½"
ASTM B564 (UNS N06625)
F-150-KL 2" - 3" ASME B16.5
Flanges
Welding Neck (WN) 4" - 24"

F-150-KB ASTM A105 Cladded
26" - 30" According to pipe Class 150 Raised Face ASME B16.47 A
F-150-LL ½" - 3" ASTM B564 (UNS N06625)
ASME B16.5
Blind 4" - 24"
F-150-LB ASTM A105 Cladded
26" - 30" ASME B16.47 A
Nuts Gasket
Spiral-Wound J-150-EM ½" - 30" - Class 150 Raised Face ASME B16.20 Inconel/graphite
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
Figure-8 Blank R8-150-RI ½" - 14"
Paddle Blank RA-150-RI According to pipe 150 Raised Face ASME - Carbon Steel ASTM A516 GR60 with Inconel
16" - 30" B16.5 625 layer
Paddle Spacer RE-150-RI
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S CS Inconel 150 B30
Clad.
Valv es (see notes)
VAG-3000-1-N102 VES-150-1-C530 0C to 150C VES-150-3-C526 VDE-150-2-N105
Needle ½" - 1 ½" -100C to 400C -100C to 200C
VAG-3000-1-N1F2 VES-150-1-C560 VES-150-3-C527 VDE-150-2-N106
0C to 210C
VES-801-1-N101 -30C to 150C VES-150-1-C570 VES-150-3-C536 0C to 150C VDE-150-2-N1F1
½" - 2" -30C to 150C
VES-801-1-N102 -46C to 150C VES-150-2-C510 VES-150-3-C537 Double VDE-150-2-N1F2
-29C to 150C
VES-801-1-N105 -100C to 200C VES-150-2-C51F VES-150-3-C53G Ball VDE-150-2-N1F5
-100C to 200C
VES-801-2-N101 -30C to 150C VES-150-2-C520 VES-150-3-C553 VDE-150-2-N1F6
-29C to 150C
VES-801-2-N102 -46C to 150C VES-150-2-C526 VES-150-3-C55G VDE-150-2-C511
0C to 150C 3" - 8" -29C to 150C
VES-801-2-N105 -100C to 200C VES-150-2-C530 Ball 2" - 30" VES-150-3-C562 VDE-150-2-C51F
VES-801-2-N107 0C to 210C Ball 2" - 30" VES-150-2-C536 VES-150-3-C563 Gate ½" - 1 ½" VGA-801-2-N101 -50C to 345C
½" - 1 ½"
Ball VES-801-2-N1F1 -30C to 150C VES-150-2-C560 VES-150-3-C56G 2" - 20" VGL-150-2-C501
0C to 210C Globe -29C to 400C
VES-801-2-N1F2 -46C to 150C VES-150-2-C562 VES-150-3-C572 2" - 18" VGL-150-2-C5F1
VES-801-2-N1F5 -100C to 200C VES-150-2-C56F VES-150-3-C573 1" - 1 ½" VRE-150-2-N133
0C to 210C
VES-801-2-N1F6 -100C to 340C VES-150-2-C56G VES-150-3-C57G VRE-800-1-N102 -100C to 400C
½" - 1 ½"
VES-801-2-N1F7 0C to 210C VES-150-2-C570 VES-150-3-C582 Check VRE-800-2-N102
-29C to 340C
VES-801-3-N105 VES-150-2-C572 VES-150-3-C58G VRE-150-2-C515 -29C to 400C
-100C to 200C 2" - 30"
VES-801-3-N1F5 VES-150-2-C580 0C to 340C Double ½" - 2" VDE-150-2-N101 VRE-150-2-C535 -29C to 240C
-30C to 150C
2" - 30" VES-150-1-C520 0C to 150C VES-150-2-C58F -29C to 340C Ball VDE-150-2-N102
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30
BRANCH SIZE
Notes
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
42 Piping, fittings and acessories shall hav e internal Inconel® 625 cladding according to I-ET-3010.00-1200-955-P4X-001 - Welding. The face of the flanges shall be supplied cladded w ith 3 mm
inconel thickness. The final dimensions of the flanges shall fulfill flange standard.
P 4X-001

C N I - Corrosive Chemical Injection (Ex cept Sodium Hypochlorite); D - Diesel; F - Safety System and Flare; F G - Fuel Gas; G - Glycol; H - Hydraulic Fluid; PC - Process (Corrosive
SS 300 C3
Hydrocarbon);
316/316L
Te mp e rature (°C) -100 38 50 100 150
S-40S
2" - 20"
Pipes
24" S-80S
Pipe -
T-323 26" 0.500" BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
28" - 30" 0.562"
36" - 38" 0.688"
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Cap C11-43
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Red Coupling C08-43
Fittings

90 LR Elbow C15-44
45 LR Elbow C16-44
90 SR Elbow C17-44
2" - 38"
Tee C20-44
Cross C24-44
Conc. Red C18-44
Ecc. Red C19-44 3" - 38"
Red Tee C21-44
Straight Nipple N-S145 1" - 1 ½" ASTM A733 ASTM A312 TP316/316L
PBE
N-C144 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E144 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E444 2" - 4" BLE x PSE
ASME B16.5
2" - 24"
Class 300 Raised Face
Welding Neck (WN) F-300-KX 26" - 30"
Flanges
ASME B16.47 A
36" - 38"
According to pipe ASTM A182 Gr F316/316L
F-350-4X ½" - 3" max 350 bar - ISO 6162-1
26" - 38" ASME B16.47 A
Nuts Gasket
A320 L7, Zn-Ni

Paddles Stud &

A194 7L, Zn-Ni
12" - 38" B16.5
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S SS 300 C3
316/316L
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-300-1-S210 -30C to 150C VES-300-3-S236 VDE-300-2-S2F2 -30C to 150C
VAG-3000-1-S202 -100C to 400C VES-300-1-S220 0C to 150C VES-300-3-S237 -46C to 150C VDE-300-2-S2F3
Needle ½" - 1 ½" -100C to 150C
VAG-3000-1-S2F1 -100C to 200C VES-300-1-S230 -46C to 150C VES-300-3-S23G VDE-300-2-S2F4
VAG-3000-1-S2F2 -100C to 400C VES-300-2-S210 VES-300-3-S252 Double ½" - 2" VDE-300-2-S2F5
-100C to 200C
3" - 20" VBO-300-2-S211 VES-300-2-S216 VES-300-3-S253 -30C to 150C Ball VDE-300-2-S2F6
-46C to 150C -30C to 150C
24" - 30" VBO-300-2-S213 VES-300-2-S21F Ball 2" - 30" VES-300-3-S25G VDE-300-2-S2F7
Butterfly -100C to 340C
3" - 20" VBO-300-2-S231 VES-300-2-S21G VES-300-3-S262 VDE-300-2-S2F8
-100C to 150C 0C to 210C
24" - 30" VBO-300-2-S233 VES-300-2-S220 VES-300-3-S263 3" - 8" VDE-300-2-S234 -46C to 150C
0C to 150C
VES-801-1-S201 -30C to 150C VES-300-2-S226 VES-300-3-S272 ½" - 1 ½" VGA-801-1-S201 -46C to 450C
Gate
VES-801-1-S202 -46C to 150C VES-300-2-S230 VES-300-3-S273 -100C to 200C 2" - 30" VGA-300-1-S231 -46C to 400C
Ball 2" - 30"
VES-801-1-S205 -100C to 200C VES-300-2-S236 VES-300-3-S27G VGL-300-1-S201
-46C to 150C -100C to 400C
VES-801-2-S201 -30C to 150C VES-300-2-S23F VDE-300-2-S201 Globe 2" - 18" VGL-300-2-S201
-30C to 150C
VES-801-2-S202 -46C to 150C VES-300-2-S23G VDE-300-2-S202 VGL-300-2-S2F1 -46C to 400C
VES-801-2-S205 -100C to 200C VES-300-2-S270 VDE-300-2-S203 Plug 2" - 24" VMA-300-2-S201 -30C to 110C
-100C to 200C -100C to 150C
Ball ½" - 1 ½" VES-801-2-S2F1 -30C to 150C VES-300-2-S27F VDE-300-2-S204 VRE-800-1-S202
Double ½" - 2" ½" - 1 ½" -100C to 400C
VES-801-2-S2F2 -46C to 150C VES-300-3-S216 Ball VDE-300-2-S205 VRE-800-2-S202
-100C to 200C
VES-801-2-S2F5 VES-300-3-S217 -30C to 150C VDE-300-2-S206 VRE-300-1-S211 0C to 150C
-100C to 200C Check
VES-801-3-S205 VES-300-3-S21G VDE-300-2-S207 2" - 30" VRE-300-2-S212
-100C to 340C
VES-801-3-S2F1 -30C to 150C VES-300-3-S226 VDE-300-2-S208 VRE-300-2-S215 -46C to 150C
0C to 150C
VES-801-3-S2F2 -46C to 150C VES-300-3-S227 VDE-300-2-S2F1 -30C to 150C 1" - 30" VRE-300-2-S235
VES-801-3-S2F5 -100C to 200C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36 38
BRANCH SIZE
Notes
55 This spec for FG serv ice is applicable for piping dow nstream the filters.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to I-ET-3010.00-1200-295-P4X-001 -Requirements for Pig Launcher
and Receiv er Design.
68 This Spec shall be applied for distribution sy stem of CO2, after directional v alv es.
P 4X-001

H F - Hot Fluid; H W P - Process Heating Water; S - Steam; SC - Steam Condensate;
Carbon 300 C4
Steel
Te mp e rature (°C) 0 38 50 100 150 200 250 300 350
Max Pre ssure (b arg ) 51.1 51.1 50.1 46.6 45.1 43.8 41.9 39.8 37.6
½" - 1 ½" XS PE API 5L Gr B PSL 1 SML
2" - 6" STD
8" S-30 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
Pipes
10" - 12" STD SAW)

Pipe T-102 - ASME B36.10
14" S-40 BE
16" - 18" XS
24" S-40
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
ASTM A105
Cap C11-02
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Red Coupling C08-02
Fittings

90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
2" - 24"
Tee C20-03
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 24"
Red Tee C21-03
PBE
N-C103 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E103 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E403 2" - 4" BLE x PSE
Nuts Gasket Flanges

Blind F-300-L2 ½" - 24"
A193 B7
Paddles Stud &

A194 Gr 2H
12" - 24" B16.5
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Carbon 300 C4
Steel
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C Butterfly 24" VBO-300-3-C163 -29C to 240C VGA-801-1-C102 VGL-300-1-C102
Needle ½" - 1 ½" ½" - 1 ½" Globe 2" - 18" -29C to 400C
VAG-3000-1-S202 -100C to 400C VES-300-2-C160 0C to 210C VGA-801-2-C101 VGL-300-2-C102
4" - 20" VBO-300-2-C111 -29C to 150C VES-300-3-C116 VGA-300-1-C131 VRE-800-1-C103
-29C to 150C Gate -29C to 400C ½" - 1 ½"
24" VBO-300-2-C113 0C to 200C Ball 2" - 24" VES-300-3-C117 VGA-300-1-C132 VRE-800-2-C103 -29C to 400C
2" - 24" Check
Butterfly 4" - 20" VBO-300-2-C131 VES-300-3-C162 VGA-300-2-C131 VRE-300-2-C113
0C to 210C 2" - 24"
24" VBO-300-2-C133 -29C to 240C VES-300-3-C163 VGA-300-2-C132 VRE-300-2-C135 -29C to 210C
6" - 20" VBO-300-3-C161
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24
BRANCH SIZE
Notes
P 4X-001

F - Safety System and Flare; G - Glycol; GL - Refrigerated Liquified Petroleum Gases in Low Temperature; P - Process (non-corrosive hydrocarbon);
Low T emp 300 C6
CS
Te mp e rature (°C) -46 0 38 50 100 150 200
½" - 1 ½" S-160 PE
2" - 6" STD
T-105 8" - 10" S-30 ASTM A333 Gr 6 SML
12" 0.344"
Pipes
Pipe 14" - ASME B36.10

STD BE
16"
18" 0.406"
20" 0.438"
24" S-30
90 Elbow C01-04
45 Elbow C02-04
Tee C03-04
ASME B16.11
Cross C05-04 ½" - 1 ½"
Cap C11-04
Red Tee C04-04
¾" - 1 ½" ASME B16.11
Red Coupling C08-04
Fittings

90 LR Elbow C15-05
45 LR Elbow C16-05
90 SR Elbow C17-05
2" - 24"
Tee C20-05
Cross C24-05
Conc. Red C18-05
Ecc. Red C19-05 3" - 24"
Red Tee C21-05
PBE
N-C105 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E105 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E405 2" - 4" BLE x PSE
Nuts Gasket Flanges

Welding Neck (WN) F-300-K3 2" - 24" According to pipe Class 300 Raised Face ASME B16.5 ASTM A350 Gr LF2 Class 1
Blind F-300-L3 ½" - 24"
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
12" - 24" B16.5
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Low T emp 300 C6
CS
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C ½" - 1 ½" VES-803-3-C2F5 -46C to 200C VES-300-3-C236 VDE-300-2-C2F5
½" - 2" -46C to 200C
VAG-3000-1-S202 -100C to 400C VES-300-1-C210 -30C to 150C VES-300-3-C237 -46C to 150C VDE-300-2-C2F6
Needle ½" - 1 ½" Double
Ball -30C to 150C
VAG-3000-1-S2F2 -100C to 400C VES-300-2-C210 VES-300-3-C252 3" - 8" VDE-300-2-C21F
VBO-300-3-C261 VES-300-2-C216 Ball 2" - 24" VES-300-3-C253 -30C to 150C VDE-300-2-C27F -46C to 200C
Butterfly - -46C to 240C -30C to 150C
VBO-300-3-C263 VES-300-2-C21F VES-300-3-C25G VGL-300-1-C201
VES-803-1-C201 -30C to 150C VES-300-2-C21G VES-300-3-C272 Globe 2" - 18" VGL-300-2-C201 -46C to 345C
VES-803-1-C205 -30C to 200C Ball VES-300-2-C230 VES-300-3-C273 -46C to 200C VGL-300-2-C2F1
2" - 24"
VES-803-2-C201 -30C to 150C VES-300-2-C236 VES-300-3-C27G Plug 2" - 24" VMA-300-2-C201 -30C to 110C
-46C to 150C
VES-803-2-C205 -46C to 200C VES-300-2-C23F VDE-300-2-C201 VRE-800-1-C202
-30C to 150C ½" - 1 ½" -46C to 345C
VES-803-2-C2F1 -30C to 150C VES-300-2-C23G VDE-300-2-C202 VRE-800-2-C202
Ball ½" - 1 ½"
VES-803-2-C2F2 -46C to 150C VES-300-2-C27F -46C to 200C Double ½" - 2" VDE-300-2-C205 VRE-300-1-C211 0C to 150C
Ball -46C to 200C Check
VES-803-2-C2F5 VES-300-3-C216 VDE-300-2-C206 VRE-300-2-C212
-46C to 200C 2" - 24" -46C to 345C
VES-803-3-C205 VES-300-3-C217 -30C to 150C VDE-300-2-C2F1 VRE-300-2-C215
-30C to 150C
VES-803-3-C2F1 -30C to 150C VES-300-3-C21G VDE-300-2-C2F2 VRE-300-2-C235 -46C to 210C
VES-803-3-C2F2 -46C to 150C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24
BRANCH SIZE
Notes
P 4X-001

AM - Amine; BG - Inert Gas; C I - Chemical Injection (non-corrosive); D - Diesel; F G - Fuel Gas; G - Glycol; IW - De-Aerated Sea Water Injection; P - Process (non-corrosive
Carbon 300 C10
hydrocarbon); SA - Service Compressed Air (utility Air); SN - Start-up Nitrogen; W - Industrial water;
Steel
Te mp e rature (°C) 0 38 50 100 150 200 240
2" - 12" STD API 5L Gr B PSL 1 (SML or WLD HFW or WLD
14" 0.406" SAW)
16" 0.469"
Pipes
18" XS
Pipe T-102 - ASME B36.10 API 5L Gr B PSL 1 WLD (HFW or SAW)
20" 0.562" BE
24" S-40
26" 0.625"
28" 0.688" API 5L Gr B PSL 1 WLD SAW
30" - 32" 0.750"
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
ASTM A105
Cap C11-02
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Red Coupling C08-02
Fittings

90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
2" - 32"
Tee C20-03
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 32"
Red Tee C21-03
Straight Nipple N-S120 1" - 1 ½" ASTM A733 API 5L Gr B PSL 1 seamless
PBE
N-C103 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E103 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E403 2" - 4" BLE x PSE
ASME B16.5
Flanges
2" - 24"
½" - 24" ASME B16.5
Blind F-300-L2
26" - 32" ASME B16.47 A
Nuts Gasket
A193 B7, Zn-Ni

Paddles Stud &
Stud and Nuts P-300-07 ½" - 1 ⅞" - - - ASME B1.1

A194 Gr 2H, Zn-Ni
12" - 32" B16.5
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Carbon 300 C10
Steel
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-300-1-C180 0C to 400C 2" - 24" VES-300-3-C11G -29C to 150C VDE-300-2-C1F1
-29C to 150C
VAG-3000-1-S202 -100C to 400C 2" - 32" VES-300-2-C110 VES-300-3-C126 VDE-300-2-C1F2
Needle ½" - 1 ½"
-29C to 150C 2" - 32" ½" - 2" -29C to 200C
VAG-3000-1-S2F2 -100C to 400C VES-300-2-C11F VES-300-3-C136 VDE-300-2-C1F6
2" - 24" Double
6" - 20" VBO-300-2-C111 -29C to 150C VES-300-2-C11G VES-300-3-C137 0C to 150C
Ball VDE-300-2-C1F7
-29C to 340C
24" - 32" VBO-300-2-C113 0C to 200C VES-300-2-C120 2" - 24" VES-300-3-C13G VDE-300-2-C1F8
Butterfly
6" - 20" VBO-300-3-C161 VES-300-2-C126 VES-300-3-C152 VDE-300-2-C114
-29C to 240C 2" - 32" 2" - 32"
24" VBO-300-3-C163 VES-300-2-C130 VES-300-3-C153 3" - 8" VDE-300-2-C115 -29C to 150C
VES-803-1-C101 -29C to 150C VES-300-2-C136 0C to 150C 2" - 24" VES-300-3-C15G -29C to 150C VDE-300-2-C11F
VES-803-1-C102 0C to 150C VES-300-2-C13F VES-300-3-C162 ½" - 1 ½" VGA-801-1-C101
2" - 24"
VES-803-1-C105 -29C to 210C VES-300-2-C13G Ball VES-300-3-C163 Gate VGA-300-1-C131 -29C to 400C
2" - 32" 2" - 32"
VES-803-2-C101 -29C to 150C VES-300-2-C150 VES-300-3-C172 0C to 210C VGA-300-2-C131
VES-803-2-C102 0C to 150C Ball VES-300-2-C152 -29C to 150C VES-300-3-C173 VGL-300-1-C101
½" - 1 ½" VES-803-2-C105 -29C to 210C VES-300-2-C160 2" - 24" VES-300-3-C17G VGL-300-2-C101
Globe 2" - 18" -29C to 400C
VES-803-2-C1F1 -29C to 150C 2" - 32" VES-300-2-C162 VES-300-3-C182 VGL-300-2-C1F1
2" - 32"
VES-803-2-C1F5 -29C to 210C VES-300-2-C16F VES-300-3-C183 0C to 400C VGL-300-2-C1F2
Ball VES-803-3-C101 -29C to 150C VES-300-2-C170 0C to 210C 2" - 24" VES-300-3-C18G VMA-150-2-C1F1
Plug 2" - 24" 0C to 110C
VES-803-3-C105 VES-300-2-C172 VES-300-4-C154 0C to 150C VMA-300-2-C101
-29C to 210C
VES-803-3-C1F5 VES-300-2-C17F VES-300-4-C164 VRE-800-1-C102
2" - 24" 6" - 32" 0C to 210C ½" - 1 ½" -29C to 400C
VES-300-1-C110 -29C to 150C VES-300-2-C17G VES-300-4-C174 VRE-800-2-C102
VES-300-1-C120 VES-300-2-C180 VES-300-4-C184 0C to 400C VRE-300-1-C111 0C to 150C
2" - 32"
VES-300-1-C130 0C to 150C VES-300-2-C182 0C to 400C VDE-300-2-C101 Check VRE-300-1-C112
2" - 32" -29C to 150C 2" - 24"
VES-300-1-C150 2" - 24" VES-300-2-C18G Double ½" - 2" VDE-300-2-C102 VRE-300-2-C112 -29C to 400C
VES-300-1-C160 VES-300-3-C116 Ball VDE-300-2-C105 VRE-300-2-C115
0C to 210C 2" - 32" -29C to 150C -29C to 200C
VES-300-1-C170 VES-300-3-C117 VDE-300-2-C106 1" - 24" VRE-300-2-C135 -29C to 210C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32
BRANCH SIZE
Notes
40 The IW serv ice is only applicable for onshore units.
46 Diesel serv ice "D" is only applicable for piping upstream the centrifuge.
56 This spec for FG serv ice is applicable for piping upstream the filters.
83 This spec for Amine serv ice is applicable for booster pump discharge.
P 4X-001

AD W - Aerated Dilution Water; PC - Process (Corrosive Hydrocarbon); PC W - Produced water;
Organic 300 C11
Coat CS
Te mp e rature (°C) 0 38 50 100 150
2" - 6" STD
8" S-20
10" 0.279" API 5L Gr B PSL 1 (SML or WLD HFW or WLD
Pipes
SAW)
Pipe T-102 12" 0.312" - ASME B36.10
BE
14" 0.344"
16" 0.406"
20" XS
90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
1" - 20"
Fittings
Tee C20-03
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 1 ½" - 20"
Red Tee C21-03
Nuts GasketFlanges Nipple
1" - 20" According to pipe Class 300 Raised Face ASME B16.5 ASTM A105
Blind F-300-L2
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
12" - 20" B16.5
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Organic 300 C11
Coat CS
Valv es (see notes)
Needle 1" - 1 ½" VAG-300-1-D201 -50C to 150C VES-300-1-D210 VES-300-3-D253 1" - 1 ½" VRE-300-1-D205 -46C to 150C
-30C to 150C Ball 2" - 20" -30C to 150C
VBO-300-2-D211 VES-300-1-D216 VES-300-3-D25G VRE-300-1-D211 0C to 150C
Butterfly 6" - 20" VBO-300-2-D251 -46C to 150C VES-300-2-D110 0C to 120C VGA-300-1-D231 VRE-300-1-D212
Gate 2" - 20" -50C to 150C Check 2" - 20"
VBO-300-3-D261 Ball 2" - 20" VES-300-2-D210 VGA-300-2-D231 VRE-300-2-D212
-46C to 150C
VES-300-1-D200 -30C to 150C VES-300-2-D21F VGL-300-1-D201 -46C to 150C VRE-300-2-D215
-30C to 150C
Ball 1" - 1 ½" VES-300-2-D200 VES-300-3-D216 Globe 2" - 18" VGL-300-2-D101 0C to 150C 1" - 20" VRE-300-2-D235
0C to 150C
VES-300-2-D2F0 VES-300-3-D217 VGL-300-2-D201 -46C to 150C
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14 16 18 20
BRANCH SIZE SOC - Sockolet
Notes
P 4X-001

PC - Process (Corrosive Hydrocarbon); PC W - Produced water;
Super 300 C12
Duplex
Te mp e rature (°C) -50 0 38 50 100 140
½" - 1 ½" PE
Pipes
2" - 8" S-40S

10" - 24" BE
26" - 30" 0.375"
90 Elbow C01-30
45 Elbow C02-30
Tee C03-30
ASME B16.11
Cross C05-30 ½" - 1 ½"
Cap C11-30
Red Tee C04-30
¾" - 1 ½" ASME B16.11
Red Coupling C08-30
Fittings

90 LR Elbow C15-32
45 LR Elbow C16-32
90 SR Elbow C17-32
2" - 30"
Tee C20-32
Cross C24-32
Conc. Red C18-32
Ecc. Red C19-32 3" - 30"
Red Tee C21-32
PBE
N-C132 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-C432 2" - 4" According to pipe - BLE x PSE ASTM A815 (UNS S32760)
MSS SP-95
N-E132 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E429 2" - 4" BLE x PSE ASTM A815 (UNS S31803)
Socket Weld (SW) F-300-JH ½" - 1 ½"
ASME B16.5
Flanges
2" - 24"
Welding Neck (WN) F-300-KH
½" - 24" ASME B16.5
Blind F-300-LH
26" - 30" ASME B16.47 A
Nuts Gasket
A320 L7, Zn-Ni

Paddles Stud &
Stud and Nuts P-300-08 ½" - 1 ¾" - - - ASME B1.1

A194 7L, Zn-Ni
Figure-8 Blank R8-300-RX ½" - 10"
Paddle Blank RA-300-RX According to pipe 300 Raised Face ASME - Superduplex ASTM A240 UNS32760
12" - 30" B16.5
Paddle Spacer RE-300-RX
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Super 300 C12
Duplex
Valv es (see notes)
VAG-3000-1-D302 VES-300-1-D310 -30C to 150C VES-300-3-D337 VDE-300-2-D3F2 -30C to 150C
Needle ½" - 1 ½" -46C to 150C
VAG-3000-1-D3F2 VES-300-1-D330 0C to 150C VES-300-3-D33G ½" - 2" VDE-300-2-D3F3
Double -46C to 150C
6" - 20" VBO-300-2-D311 VES-300-2-D310 VES-300-3-D352 VDE-300-2-D3F4
0C to 150C Ball
24" - 30" VBO-300-2-D313 VES-300-2-D316 2" - 30" VES-300-3-D353 VDE-300-2-D31F -30C to 150C
Butterfly -30C to 150C 3" - 8"
- VBO-300-3-D361 VES-300-2-D31F Ball VES-300-3-D372 0C to 150C VDE-300-2-D334 -46C to 150C
-46C to 150C
24" - 30" VBO-300-3-D363 VES-300-2-D31G VES-300-3-D373 ½" - 1 ½" VGA-801-1-D301
Gate -50C to 150C
VES-801-1-D301 VES-300-2-D330 VES-300-3-D37G 2" - 30" VGA-300-1-D331
Ball 2" - 30"
VES-801-1-D305 VES-300-2-D336 VES-300-4-D354 VGL-300-2-D301
0C to 150C 0C to 150C 6" - 30" Globe 2" - 18" -46C to 150C
VES-801-2-D301 VES-300-2-D33F VES-300-4-D374 VGL-300-2-D3F1
VES-801-2-D305 VES-300-2-D33G VDE-300-2-D301 VRE-800-1-D302
Ball ½" - 1 ½" -30C to 150C ½" - 1 ½" -46C to 150C
VES-801-2-D3F1 -30C to 150C VES-300-3-D316 VDE-300-2-D302 VRE-800-2-D302
VES-801-2-D3F5 VES-300-3-D317 -30C to 150C
Double ½" - 2" VDE-300-2-D303 Check VRE-300-1-D312 -50C to 150C
Ball -46C to 150C 2" - 30"
VES-801-3-D305 0C to 150C VES-300-3-D31G VDE-300-2-D304 VRE-300-2-D315
-46C to 150C
VES-801-3-D3F5 VES-300-3-D336 0C to 150C VDE-300-2-D3F1 -30C to 150C 1" - 30" VRE-300-2-D335
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
26 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30
BRANCH SIZE
Notes
123 The application of this pipe specification for PCW - Produced Water is conditioned to max imum ox y gen content 20 ppb and max temperature 120ºC.
P 4X-001

AM - Amine; PC - Process (Corrosive Hydrocarbon); PC W - Produced water;
Duplex 300 C16
Te mp e rature (°C) -46 0 38 50 100 150
½" - 1 ½" PE
2" - 8"
10" - 20" S-40S
Pipes
22"
24" BE
26" - 28" 0.375"
30" 0.406"
32" 0.438"
90 Elbow C01-27
45 Elbow C02-27
Tee C03-27
ASME B16.11
Cross C05-27 ½" - 1 ½"
Cap C11-27
Red Tee C04-27
¾" - 1 ½" ASME B16.11
Red Coupling C08-27
Fittings

90 LR Elbow C15-29
45 LR Elbow C16-29
90 SR Elbow C17-29
2" - 32"
Tee C20-29
Cross C24-29
Conc. Red C18-29
Ecc. Red C19-29 3" - 32"
Red Tee C21-29
PBE
N-C129 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E129 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E429 2" - 4" BLE x PSE
2" - 20"
ASME B16.5
Flanges
22"
Welding Neck (WN) F-300-KG
24" According to pipe Class 300 Raised Face ASTM A182 Gr F51
26" - 32" ASME B16.47 A
½" - 24" ASME B16.5
Blind F-300-LG
26" - 32" ASME B16.47 A
½" - 20"
Stud & Gasket
Spiral-Wound J-300-EL 22" - Class 300 Raised Face ASME B16.20 Duplex/graphite
24" - 32"
A193 B7, Zn-Ni
Nuts

A194 Gr 2H, Zn-Ni
12" - 20"
Paddles
Paddle Blank RA-300-RD 22"

24" - 32" According to pipe 300 Raised Face ASME - Duplex Stainless Steel ASTM A240 UNS31803
B16.5
12" - 20"
Paddle Spacer RE-300-RD 22"
24" - 32"
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Duplex 300 C16
Valv es (see notes)
VAG-3000-1-D202 VES-300-1-D260 0C to 150C VES-300-2-D27G -46C to 150C VDE-300-2-D202 -30C to 150C
Needle ½" - 1 ½" -46C to 150C
VAG-3000-1-D2F2 VES-300-1-D270 -46C to 150C VES-300-3-D216 VDE-300-2-D203
-46C to 150C
6" - 20" VBO-300-2-D211 VES-300-2-D210 VES-300-3-D217 -30C to 150C VDE-300-2-D204
24" - 32" VBO-300-2-D213 VES-300-2-D216 VES-300-3-D21G Double ½" - 2" VDE-300-2-D2F1
Ball -30C to 150C
6" - 20" VBO-300-2-D251 VES-300-2-D21F VES-300-3-D226 VDE-300-2-D2F2
0C to 150C
24" - 32" VBO-300-2-D253 VES-300-2-D21G VES-300-3-D227 VDE-300-2-D2F3
-46C to 150C
VES-801-1-D201 -30C to 150C VES-300-2-D220 VES-300-3-D236 VDE-300-2-D2F4
0C to 150C
VES-801-1-D202 VES-300-2-D226 VES-300-3-D237 -46C to 150C 3" - 8" VDE-300-2-D21F -30C to 150C
-46C to 150C
VES-801-1-D205 VES-300-2-D230 2" - 32" VES-300-3-D23G ½" - 1 ½" VGA-801-1-D201
VES-801-2-D201 -30C to 150C VES-300-2-D236 VES-300-3-D252 Gate VGA-300-1-D231 -50C to 150C
-46C to 150C Ball 2" - 32"
VES-801-2-D202 Ball 2" - 32" VES-300-2-D23F VES-300-3-D253 -30C to 150C VGA-300-2-D231
-46C to 150C
½" - 1 ½" VES-801-2-D205 VES-300-2-D23G VES-300-3-D25G VGL-300-1-D201
VES-801-2-D2F1 -30C to 150C VES-300-2-D250 VES-300-3-D262 Globe 2" - 18" VGL-300-2-D201 -46C to 150C
0C to 150C
Ball VES-801-2-D2F2 VES-300-2-D252 VES-300-3-D263 VGL-300-2-D2F1
-30C to 150C
VES-801-2-D2F5 VES-300-2-D25F VES-300-3-D272 VRE-800-1-D202
-46C to 150C ½" - 1 ½" -46C to 150C
VES-801-3-D205 VES-300-2-D25G VES-300-3-D273 -46C to 150C VRE-800-2-D202
VES-801-3-D2F5 VES-300-2-D260 VES-300-3-D27G VRE-300-1-D211 0C to 150C
0C to 150C Check
VES-300-1-D210 -30C to 150C VES-300-2-D262 VES-300-4-D254 -30C to 150C VRE-300-2-D212
2" - 32"
VES-300-1-D220 0C to 150C VES-300-2-D270 6" - 32" VES-300-4-D264 0C to 150C VRE-300-2-D215 -46C to 150C
2" - 32"
VES-300-1-D230 -46C to 150C VES-300-2-D272 -46C to 150C VES-300-4-D274 -46C to 150C VRE-300-2-D235
VES-300-1-D250 -30C to 150C VES-300-2-D27F Double ½" - 2" VDE-300-2-D201 -30C to 150C
Ball
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
24 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE TEE
28 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32
BRANCH SIZE
Notes
58 This spec for Amine serv ice is applicable for piping dow nstream the booster pump.
82 Use this Spec after SG (free w ater separator).
P 4X-001

F - Safety System and Flare; PC - Process (Corrosive Hydrocarbon);
Low T emp 300 C19
CS
Te mp e rature (°C) -46 0 38 50 100 150 200
½" - 1 ½" S-160 PE
2" XS
3" - 4" 0.250"
T-105 6" 0.312" ASTM A333 Gr 6 SML
8" 0.344"
10" - 12" 0.438"
Pipes
Pipe 14" S-40 - ASME B36.10

BE
16" 0.469"
18" XS
20" 0.562"
24" 0.625"
26" 0.688"
28" - 30" 0.750"
90 Elbow C01-04
45 Elbow C02-04
Tee C03-04
ASME B16.11
Cross C05-04 ½" - 1 ½"
Cap C11-04
Red Tee C04-04
¾" - 1 ½" ASME B16.11
Red Coupling C08-04
Fittings

90 LR Elbow C15-05
45 LR Elbow C16-05
90 SR Elbow C17-05
2" - 30"
Tee C20-05
Cross C24-05
Conc. Red C18-05
Ecc. Red C19-05 3" - 30"
Red Tee C21-05
Straight Nipple N-S137
½" - 1 ½" ASTM A733 ASTM A333 Gr 6
PBE
N-C105
¾" - 1 ½"
Swage Conc Nipple 2"
Nipple
N-C405 BLE x PSE

4" According to pipe -
N-E105 ¾" - 1 ½" PBE
Swage Ecc Nipple 2"
N-E405 BLE x PSE
4"
ASME B16.5
Flanges
2" - 24"
½" - 24" ASME B16.5
Blind F-300-L3
26" - 30" ASME B16.47 A
Nuts Gasket
A193 B7, Zn-Ni

Paddles Stud &

A194 Gr 2H, Zn-Ni
12" - 30" B16.5
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Low T emp 300 C19
CS
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-803-3-C2F2 -46C to 150C VES-300-3-C21G -30C to 150C VDE-300-2-C2F2 -30C to 150C
½" - 1 ½"
VAG-3000-1-S202 -100C to 400C VES-803-3-C2F5 -46C to 200C VES-300-3-C236 ½" - 2" VDE-300-2-C2F5
Needle ½" - 1 ½" Double -46C to 200C
VAG-3000-1-S2F1 -100C to 200C VES-300-1-C210 -30C to 150C VES-300-3-C237 -46C to 150C VDE-300-2-C2F6
Ball
3" - 8" -30C to 150C
VBO-300-3-C261 VES-300-2-C210 VES-300-3-C252 VDE-300-2-C21F
Butterfly - -46C to 240C Ball 2" - 30"
VBO-300-3-C263 VES-300-2-C216 VES-300-3-C253 -30C to 150C VGL-300-1-C201
-30C to 150C
VES-803-1-C201 -30C to 150C VES-300-2-C21F VES-300-3-C25G Globe 2" - 18" VGL-300-2-C201 -46C to 345C
VES-803-1-C205 -30C to 200C Ball VES-300-2-C21G VES-300-3-C272 VGL-300-2-C2F1
VES-803-2-C201 -30C to 150C 2" - 30" VES-300-2-C230 VES-300-3-C273 -46C to 200C Plug 2" - 12" VMA-300-2-C201 -30C to 110C
VES-803-2-C205 -46C to 200C VES-300-2-C236 VES-300-3-C27G VRE-800-1-C202
-46C to 150C ½" - 1 ½" -46C to 345C
Ball ½" - 1 ½" VES-803-2-C2F1 -30C to 150C VES-300-2-C23F VDE-300-2-C201 VRE-800-2-C202
-30C to 150C
VES-803-2-C2F2 -46C to 150C VES-300-2-C23G VDE-300-2-C202 VRE-300-1-C211 0C to 150C
Double ½" - 2" Check
VES-803-2-C2F5 VES-300-2-C270 -46C to 200C
Ball VDE-300-2-C205 VRE-300-2-C212
-46C to 200C -46C to 200C 2" - 30" -46C to 345C
VES-803-3-C205 VES-300-3-C216 VDE-300-2-C206 VRE-300-2-C215
-30C to 150C
VES-803-3-C2F1 -30C to 150C VES-300-3-C217 VDE-300-2-C2F1 -30C to 150C VRE-300-2-C235 -46C to 210C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30
BRANCH SIZE
Notes
P 4X-001

AD W - Aerated Dilution Water; SW - Aerated Sea Water;
F RP 25 bar C23
Te mp e rature (°C) 90
Max Pre ssure (b arg ) 25
Pipes
Pipe T-410 1" - 28" acc. manufact. - ISO 14692 fiberglass type E or E-CR. Design pressure 25
Bell-Spigot bar@90ºC. SML
1" - 1 ½"
Thd Saddle C52-64 -
- -
90 LR Elbow C15-64
Fittings
45 LR Elbow C16-64 According to pipe FRP - Bisphenol A Epoxy resins reinforced with
1" - 28"
Tee C20-64 ISO 14692 fiberglass type E or E-CR. Design pressure
FRP Stub End C64-64 25 bar Butt-Strap 25bar@90ºC
-
FRP Ecc. Red. C62-64 2" - 28"
Red Tee C63-64
Nuts Gasket Flanges
Blind F-25-LT B16.5/B16.47 CL300 fiberglass type E or E-CR. Suitable for 90°C.
1" - 28" According to pipe 25 bar Raised Face Drilling acc. B16.5/B16.47
Backing Flange F-25-YV CL300 ASTM A105 Epoxy coated
Flat type J-300-P3 1" - 28" - Class 300 Raised Face ASME B16.21 Neoprene
A193 B7, Zn-Ni

Paddles Stud &
Stud and Nuts P-300-07 ½" - 1 ⅝" - - - ASME B1.1

A194 Gr 2H, Zn-Ni
12" - 28" B16.5
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S F RP 25 bar C23
Valv es (see notes)
4" - 20" VBO-300-2-U311 Gate 1" - 24" VGA-300-1-U331 0C to 90C VRE-300-1-U311 VRE-300-1-U315
Butterfly 0C to 90C Check 2" - 28" 0C to 90C Check 2" - 28" 0C to 90C
24" - 28" VBO-300-2-U313 Globe 2" - 12" VGL-300-1-U301 0C to 90C VRE-300-1-U312 VRE-300-2-U335
Branch (see notes)
1 TEE
1.5 RTEE TEE
2.5 FSDL RTEE RTEE TEE
1 1.5 2 2.5 3 4 6 8 10 12 14 16 18 20 24 26 28
BRANCH SIZE
Notes
P 4X-001

IW - De-Aerated Sea Water Injection; PC - Process (Corrosive Hydrocarbon); PC W - Produced water;
CS Inconel 300 C30
Clad.
Te mp e rature (°C) -20 0 38 50 100 150 200
½" - 1 ½" PE
2" - 3"
4" - 6" STD
8" S-20
10" 0.279" API 5L Gr B PSL 1 (SML or WLD HFW or WLD
SAW)
12" 0.312"
Pipes
14" 0.344"
Pipe -
16" 0.406" BE
T-102 ASME B36.10
18" S-30
API 5L Gr B PSL 1 WLD (HFW or SAW)
20" XS
24"
0.625"
26"
28" S-30 API 5L Gr B PSL 1 WLD SAW
30" 0.688"
90 Elbow C01-33
45 Elbow C02-33
Tee C03-33
ASME B16.11
Cross C05-33 ½" - 1 ½"
Cap C11-33
Red Tee C04-33
¾" - 1 ½" ASME B16.11 ASTM B366 (UNS N06625)
Red Coupling C08-33
Weldolet C12-33 MSS SP-97
90 LR Elbow C15-33
45 LR Elbow C16-33
90 SR Elbow C17-33 2" - 3"
ASME B16.9
Tee C20-33
Fittings
Cap C22-33
Cross C24-33
Conc. Red C18-33
Ecc. Red C19-33 3" - 4" ASTM B366 (UNS N06625)
Red Tee C21-33
90 LR Elbow C15-03
45 LR Elbow C16-03
90 SR Elbow C17-03
4" - 30" ASME B16.9
Tee C20-03
Cap C22-03 ASTM A234 Gr WPB
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 6" - 30"
Red Tee C21-03
PBE
N-C133 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E133 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E433 2" - 4" BLE x PSE
F-300-KL 2" - 3" ASME B16.5
Flanges
Welding Neck (WN) 4" - 24"

F-300-KB ASTM A105 Cladded
26" - 30" According to pipe Class 300 Raised Face ASME B16.47 A
F-300-LL ½" - 3" ASTM B564 (UNS N06625)
ASME B16.5
Blind 4" - 24"
F-300-LB ASTM A105 Cladded
26" - 30" ASME B16.47 A
Nuts Gasket
A193 B7, Zn-Ni

Paddles Stud &
Stud and Nuts P-300-07 ½" - 1 ⅝" - - - ASME B1.1

A194 Gr 2H, Zn-Ni
12" - 30" B16.5 625 layer
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S CS Inconel 300 C30
Clad.
Valv es (see notes)
VAG-3000-1-N102 VES-300-1-C560 VES-300-3-C517 VDE-300-2-N106 -100C to 200C
Needle ½" - 1 ½" -100C to 400C 0C to 210C -29C to 150C
VAG-3000-1-N1F2 VES-300-1-C570 VES-300-3-C51G VDE-300-2-N1F1
-30C to 150C
VES-801-1-N101 -30C to 150C VES-300-2-C510 VES-300-3-C526 ½" - 2" VDE-300-2-N1F2
-29C to 150C
VES-801-1-N102 -46C to 150C VES-300-2-C51F VES-300-3-C527 Double VDE-300-2-N1F5
-100C to 200C
VES-801-1-N105 -100C to 200C VES-300-2-C520 VES-300-3-C536 0C to 150C Ball VDE-300-2-N1F6
VES-801-2-N101 -30C to 150C VES-300-2-C526 VES-300-3-C537 VDE-300-2-C510
-29C to 150C
VES-801-2-N102 -46C to 150C VES-300-2-C52F VES-300-3-C53G 3" - 8" VDE-300-2-C51F
VES-801-2-N105 -100C to 200C VES-300-2-C530 0C to 150C Ball 2" - 30" VES-300-3-C553 VDE-300-2-C57F -29C to 200C
-29C to 150C
½" - 1 ½" VES-801-2-N1F1 -30C to 150C VES-300-2-C536 VES-300-3-C55G VGL-300-1-C501
Ball 2" - 30" 2" - 20"
VES-801-2-N1F2 -46C to 150C VES-300-2-C53F VES-300-3-C562 Globe VGL-300-2-C501 -29C to 400C
Ball
VES-801-2-N1F5 -100C to 200C VES-300-2-C53G VES-300-3-C563 2" - 18" VGL-300-2-C5F1
VES-801-2-N1F6 -100C to 340C VES-300-2-C560 VES-300-3-C56G 1" - 1 ½" VRE-300-2-N133
0C to 210C
VES-801-2-N1F7 0C to 210C VES-300-2-C562 0C to 210C VES-300-3-C572 VRE-800-1-N102 -100C to 400C
½" - 1 ½"
VES-801-3-N105 VES-300-2-C56F VES-300-3-C573 VRE-800-2-N102
-100C to 200C
VES-801-3-N1F5 VES-300-2-C570 VES-300-3-C57G Check VRE-300-1-C512
VES-300-1-C510 -29C to 150C VES-300-2-C572 VDE-300-2-N101 VRE-300-2-C512 -29C to 400C
-29C to 200C Double ½" - 2" -30C to 150C 2" - 30"
2" - 30" VES-300-1-C520 VES-300-2-C57F Ball VDE-300-2-N102 VRE-300-2-C515
0C to 150C
VES-300-1-C530 VES-300-2-C57G VDE-300-2-N105 -100C to 200C VRE-300-2-C535 -29C to 210C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30
BRANCH SIZE
Notes
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
103 Use this Spec after choke v alv e up to SG (free w ater separator).
P 4X-001

AM - Amine; C N I - Corrosive Chemical Injection (Ex cept Sodium Hypochlorite); F G - Fuel Gas; G - Glycol; H - Hydraulic Fluid; P - Process (non-corrosive hydrocarbon); PC -
SS 600 E3
Process (Corrosive Hydrocarbon);
316/316L
Te mp e rature (°C) -100 38 50 100 150 200
S-40S
2" - 8"
10" - 14" S-80S
16" 0.625"
18" 0.688"
Pipes
Pipe 20" 0.750" -

T-323 BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
24" 0.875"
26" 0.938"
28" 1.000"
30" 1.062"
32" 1.188"
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Cap C11-43
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Red Coupling C08-43
Fittings

90 LR Elbow C15-44
45 LR Elbow C16-44
90 SR Elbow C17-44
2" - 32"
Tee C20-44
Cross C24-44
Conc. Red C18-44
Ecc. Red C19-44 3" - 32"
Red Tee C21-44
PBE
N-C144 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E144 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E444 2" - 4" BLE x PSE
ASME B16.5
2" - 24" Class 600 Raised Face
Welding Neck (WN) F-600-KX
Flanges
26" - 32" ASME B16.47 A

26" - 32" ASME B16.47 A
Nuts Gasket
A320 L7, Zn-Ni

Paddles Stud &

A194 7L, Zn-Ni
10" - 32" B16.5
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S SS 600 E3
316/316L
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-600-1-S250 -30C to 150C VES-600-3-S219 VDE-600-2-S2F4 -46C to 150C
-30C to 150C
VAG-3000-1-S202 -100C to 400C VES-600-1-S260 0C to 210C VES-600-3-S21G ½" - 2" VDE-600-2-S2F5
Needle ½" - 1 ½" -100C to 200C
VAG-3000-1-S2F1 -100C to 200C VES-600-1-S270 -100C to 200C VES-600-3-S228 VDE-600-2-S2F6
0C to 150C
VAG-3000-1-S2F2 -100C to 400C VES-600-2-S214 VES-600-3-S229 VDE-600-2-S214
6" - 20" VBO-600-3-S261 VES-600-2-S218 VES-600-3-S238 VDE-600-2-S215 -30C to 150C
24" - 32" VBO-600-3-S263 VES-600-2-S21F VES-600-3-S239 -46C to 150C VDE-600-2-S21F
VES-801-1-S203 VES-600-2-S21G VES-600-3-S23G Double VDE-600-2-S224
-30C to 150C Ball
VES-801-1-S204 VES-600-2-S224 Ball 2" - 32" VES-600-3-S252 VDE-600-2-S225 0C to 150C
0C to 150C
VES-801-1-S205 -100C to 200C VES-600-2-S228 VES-600-3-S253 -30C to 150C 3" - 8" VDE-600-2-S22F
VES-801-2-S202 -46C to 150C VES-600-2-S234 VES-600-3-S25G VDE-600-2-S234
VES-801-2-S203 -30C to 150C VES-600-2-S238 VES-600-3-S262 VDE-600-2-S235 -46C to 150C
-46C to 150C 0C to 210C
VES-801-2-S204 -46C to 150C VES-600-2-S23F VES-600-3-S263 VDE-600-2-S23F
Ball 2" - 32"
VES-801-2-S205 -100C to 200C VES-600-2-S23G VES-600-3-S272 VDE-600-2-S270
-100C to 200C
VES-801-2-S2F3 -30C to 150C VES-600-2-S250 VES-600-3-S273 -100C to 200C VDE-600-2-S27F
½" - 1 ½"
VES-801-2-S2F4 -46C to 150C VES-600-2-S252 VES-600-3-S27G ½" - 1 ½" VGA-801-1-S201 -46C to 450C
-30C to 150C Gate
Ball VES-801-2-S2F5 -100C to 200C VES-600-2-S25F VDE-600-2-S201 2" - 16" VGA-600-1-S231 -46C to 400C
-30C to 150C
VES-801-3-S203 -30C to 150C VES-600-2-S25G VDE-600-2-S202 2" - 4" VGL-600-1-S201
VES-801-3-S204 -46C to 150C VES-600-2-S260 VDE-600-2-S203 Globe VGL-600-2-S201 -100C to 400C
0C to 210C -46C to 150C 2" - 18"
VES-801-3-S205 -100C to 200C VES-600-2-S262 VDE-600-2-S204 VGL-600-2-S2F1
VES-801-3-S2F3 -30C to 150C VES-600-2-S270 Double ½" - 2" VDE-600-2-S205 Plug 2" - 16" VMA-600-2-S201 -30C to 110C
Ball -100C to 200C
VES-801-3-S2F4 -46C to 150C VES-600-2-S272 VDE-600-2-S206 ½" - 1 ½" VRE-800-2-S202
-100C to 200C
VES-801-3-S2F5 -100C to 200C VES-600-2-S27F VDE-600-2-S2F1 VRE-600-2-S212 -100C to 400C
-30C to 150C Check 2" - 24"
VES-600-1-S214 -30C to 150C VES-600-2-S27G VDE-600-2-S2F2 VRE-600-2-S215
2" - 32" VES-600-1-S224 0C to 150C VES-600-3-S218 -30C to 150C VDE-600-2-S2F3 -46C to 150C 1" - 24" VRE-600-2-S235 -100C to 200C
VES-600-1-S234 -46C to 150C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32
BRANCH SIZE
Notes
55 This spec for FG serv ice is applicable for piping dow nstream the filters.
P 4X-001

F G - Fuel Gas; G - Glycol; GL - Refrigerated Liquified Petroleum Gases in Low Temperature; P - Process (non-corrosive hydrocarbon);
Low T emp 600 E6
CS
Te mp e rature (°C) -46 0 38 50 100 150 180
½" - 1 ½" S-160 PE
2" XS
3" STD
4" 0.281"
T-105 6" 0.375" ASTM A333 Gr 6 SML
Pipes
Pipe 8" 0.438" - ASME B36.10

BE
10" 0.562"
12" 0.625"
14" 0.688"
16" - 24" S-60
26" 1.062"
90 Elbow C01-04
45 Elbow C02-04
Tee C03-04
ASME B16.11
Cross C05-04 ½" - 1 ½"
Cap C11-04
Red Tee C04-04
¾" - 1 ½" ASME B16.11
Red Coupling C08-04
Fittings

90 LR Elbow C15-05
45 LR Elbow C16-05
90 SR Elbow C17-05
2" - 26"
Tee C20-05
Cross C24-05
Conc. Red C18-05
Ecc. Red C19-05 3" - 26"
Red Tee C21-05
PBE
N-C105 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E105 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E405 2" - 3" BLE x PSE
ASME B16.5
Flanges
2" - 24"
26" According to pipe Class 600 Raised Face ASME B16.47 A ASTM A350 Gr LF2 Class 1
½" - 24" ASME B16.5
Blind F-600-L3
26" ASME B16.47 A
Nuts Gasket
A320 L7, Zn-Ni

Paddles Stud &

A194 7L, Zn-Ni
10" - 26" B16.5
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Low T emp 600 E6
CS
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-600-1-C214 -30C to 150C VES-600-3-C252 VDE-600-2-C2F5
½" - 2" -46C to 200C
VAG-3000-1-S202 -100C to 400C VES-600-1-C234 -46C to 150C VES-600-3-C253 VDE-600-2-C2F6
Needle ½" - 1 ½" -30C to 150C
VAG-3000-1-S2F1 -100C to 200C VES-600-2-C214 VES-600-3-C25G VDE-600-2-C214
2" - 26"
VAG-3000-1-S2F2 -100C to 400C VES-600-2-C218 VES-600-3-C272 Double VDE-600-2-C215 -30C to 150C
-30C to 150C Ball Ball
VES-803-1-C203 -30C to 150C VES-600-2-C21F VES-600-3-C273 VDE-600-2-C21F
-46C to 200C 3" - 8"
VES-803-1-C205 -30C to 200C VES-600-2-C21G VES-600-3-C27G VDE-600-2-C234
VES-803-2-C203 -30C to 150C VES-600-2-C234 VES-600-4-C254 -30C to 150C VDE-600-2-C235 -46C to 150C
6" - 26"
VES-803-2-C204 -46C to 150C VES-600-2-C238 VES-600-4-C274 -46C to 200C VDE-600-2-C23F
-46C to 150C
VES-803-2-C205 -46C to 200C VES-600-2-C23F VDE-600-2-C201 VGL-600-1-C201
Ball 2" - 26" -30C to 150C
VES-803-2-C2F3 -30C to 150C VES-600-2-C23G VDE-600-2-C202 Globe 2" - 20" VGL-600-2-C201 -46C to 345C
VES-803-2-C2F4 -46C to 150C VES-600-2-C252 -30C to 150C VDE-600-2-C203 VGL-600-2-C2F1
Ball ½" - 1 ½" -46C to 150C
VES-803-2-C2F5 -46C to 200C VES-600-2-C270 -46C to 200C VDE-600-2-C204 Plug 2" - 24" VMA-600-2-C201 -30C to 110C
VES-803-3-C203 -30C to 150C VES-600-3-C218 Double VDE-600-2-C205 ½" - 1 ½" VRE-800-2-C202 -46C to 345C
VES-803-3-C204 -46C to 150C VES-600-3-C219 -30C to 150C Ball ½" - 2" VDE-600-2-C206
-46C to 200C
2" - 4" VRE-600-1-C211 0C to 150C
VES-803-3-C205 -46C to 200C VES-600-3-C21G VDE-600-2-C2F1 Check VRE-600-2-C212
-30C to 150C 2" - 26" -46C to 345C
VES-803-3-C2F3 -30C to 150C VES-600-3-C238 VDE-600-2-C2F2 VRE-600-2-C215
VES-803-3-C2F4 -46C to 150C VES-600-3-C239 -46C to 150C VDE-600-2-C2F3 1" - 26" VRE-600-2-C235 -46C to 210C
-46C to 150C
VES-803-3-C2F5 -46C to 200C VES-600-3-C23G VDE-600-2-C2F4
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26
BRANCH SIZE
Notes
P 4X-001

AM - Amine; PC - Process (Corrosive Hydrocarbon);
Duplex 600 E16
Te mp e rature (°C) -46 0 38 50 100 130
½" - 1 ½" PE
Pipes
2" - 8" S-40S

10" - 12" BE
14" - 18" S-80S
90 Elbow C01-27
45 Elbow C02-27
Tee C03-27
ASME B16.11
Cross C05-27 ½" - 1 ½"
Cap C11-27
Red Tee C04-27
¾" - 1 ½" ASME B16.11
Red Coupling C08-27
Fittings

90 LR Elbow C15-29
45 LR Elbow C16-29
90 SR Elbow C17-29
2" - 18"
Tee C20-29
Cross C24-29
Conc. Red C18-29
Ecc. Red C19-29 3" - 18"
Red Tee C21-29
PBE
N-C129 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E129 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E429 2" - 4" BLE x PSE
Nuts Gasket Flanges

Welding Neck (WN) F-600-KG 2" - 18" According to pipe Class 600 Raised Face ASME B16.5 ASTM A182 Gr F51
Blind F-600-LG ½" - 18"
A320 L7, Zn-Ni

Paddles Stud &

A194 7L, Zn-Ni
Paddle Blank RA-600-RD According to pipe 600 Raised Face ASME - Duplex Stainless Steel ASTM A240 UNS31803
10" - 18" B16.5
Paddle Spacer RE-600-RD
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Duplex 600 E16
Valv es (see notes)
VAG-3000-1-D202 VES-600-2-D218 VES-600-3-D253 VDE-600-2-D21F -30C to 150C
Needle ½" - 1 ½" -46C to 150C -30C to 150C
VAG-3000-1-D2F2 VES-600-2-D21F -30C to 150C VES-600-3-D25G VDE-600-2-D224
Butterfly 6" - 16" VBO-600-3-D261 -46C to 150C VES-600-2-D21G VES-600-3-D262 VDE-600-2-D225 0C to 150C
0C to 150C Double 3" - 8"
VES-801-1-D203 -30C to 150C VES-600-2-D224 Ball 2" - 18" VES-600-3-D263 Ball VDE-600-2-D22F
0C to 150C
VES-801-1-D204 VES-600-2-D228 VES-600-3-D272 VDE-600-2-D234
-46C to 150C
VES-801-1-D205 VES-600-2-D234 VES-600-3-D273 -46C to 150C VDE-600-2-D235 -46C to 150C
VES-801-2-D203 -30C to 150C VES-600-2-D238 VES-600-3-D27G VDE-600-2-D23F
-46C to 150C
VES-801-2-D204 VES-600-2-D23F VDE-600-2-D201 ½" - 1 ½" VGA-801-1-D201
-46C to 150C -30C to 150C Gate -50C to 150C
½" - 1 ½" VES-801-2-D205 VES-600-2-D23G VDE-600-2-D202 2" - 16" VGA-600-1-D231
Ball 2" - 18"
VES-801-2-D2F3 -30C to 150C VES-600-3-D218 VDE-600-2-D203 2" - 4" VGL-600-1-D201
-46C to 150C
Ball VES-801-2-D2F4 VES-600-3-D219 -30C to 150C VDE-600-2-D204 Globe VGL-600-2-D201 -46C to 150C
½" - 2" 2" - 12"
VES-801-2-D2F5 VES-600-3-D21G Double VDE-600-2-D2F1 VGL-600-2-D2F1
-46C to 150C -30C to 150C
VES-801-3-D205 VES-600-3-D228 Ball VDE-600-2-D2F2 ½" - 1 ½" VRE-800-1-D202 -46C to 150C
0C to 150C
VES-801-3-D2F5 VES-600-3-D229 VDE-600-2-D2F3 2" - 4" VRE-600-1-D211 0C to 150C
-46C to 150C
VES-600-1-D214 -30C to 150C VES-600-3-D238 VDE-600-2-D2F4 Check VRE-600-2-D212
2" - 18"
VES-600-1-D224 0C to 150C VES-600-3-D239 -46C to 150C VDE-600-2-D214 VRE-600-2-D215 -46C to 150C
2" - 18" 3" - 8" -30C to 150C
VES-600-1-D234 -46C to 150C VES-600-3-D23G VDE-600-2-D215 1" - 12" VRE-600-2-D235
VES-600-2-D214 -30C to 150C VES-600-3-D252 -30C to 150C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 SOC - Sockolet
BRANCH SIZE
Notes
49 This spec for Amine serv ice is applicable for piping dow nstream the Amine Contactor.
P 4X-001

Low T emp 600 E19
CS
Te mp e rature (°C) -46 0 38 50 100 150 200 250 300 325
Max Pre ssure (b arg ) 102.1 102.1 102.1 100.2 93.2 90.2 87.6 83.9 79.6 77.4
½" - 1 ½" S-160 PE
2" 0.250"
3" - 8" XS
Pipes
10" - 14" S-80

Pipe - ASME B36.10
16" 0.750" BE
18" 0.812"
20" 0.875"
24" 1.000"
90 Elbow C01-04
45 Elbow C02-04
Tee C03-04
ASME B16.11
Cross C05-04 ½" - 1 ½"
Cap C11-04
Red Tee C04-04
¾" - 1 ½" ASME B16.11
Red Coupling C08-04
Fittings

90 LR Elbow C15-05
45 LR Elbow C16-05
90 SR Elbow C17-05
2" - 24"
Tee C20-05
Cross C24-05
Conc. Red C18-05
Ecc. Red C19-05 3" - 24"
Red Tee C21-05
PBE
N-C105 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E105 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E405 2" - 4" BLE x PSE
Nuts Gasket Flanges

Welding Neck (WN) F-600-K3 2" - 24" According to pipe Class 600 Raised Face ASME B16.5 ASTM A350 Gr LF2 Class 1
Blind F-600-L3 ½" - 24"
A320 L7
Paddles Stud &

A194 7L
Paddle Blank RA-600-RL 10" - 24" According to pipe 600 Raised Face ASME - Low Temp. Carbon Steel ASTM A516 70 + S5
B16.5
Paddle Spacer RE-600-RL ½" - 24"
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Low T emp 600 E19
CS
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-600-1-C234 -46C to 150C VES-600-3-C25G VDE-600-2-C2F7
-30C to 150C ½" - 2" -46C to 400C
VAG-3000-1-S202 -100C to 400C VES-600-2-C214 VES-600-3-C272 VDE-600-2-C2F8
Needle ½" - 1 ½"
VAG-3000-1-S2F1 -100C to 200C VES-600-2-C218 2" - 24" VES-600-3-C273 VDE-600-2-C214
-30C to 150C -46C to 200C
VAG-3000-1-S2F2 -100C to 400C VES-600-2-C21F Ball VES-600-3-C27G VDE-600-2-C215 -30C to 150C
VES-803-1-C203 -30C to 150C VES-600-2-C21G VES-600-3-C28G -46C to 400C Double VDE-600-2-C21F
VES-803-1-C205 -30C to 200C VES-600-2-C234 VES-600-4-C254 -30C to 150C Ball VDE-600-2-C234
6" - 24" 3" - 8"
VES-803-2-C203 -30C to 150C VES-600-2-C238 VES-600-4-C274 -46C to 200C VDE-600-2-C235 -46C to 150C
-46C to 150C
VES-803-2-C204 -46C to 150C VES-600-2-C23F VDE-600-2-C201 VDE-600-2-C23F
-30C to 150C
VES-803-2-C205 -46C to 200C VES-600-2-C23G VDE-600-2-C202 VDE-600-2-C27F -46C to 200C
VES-803-2-C2F3 -30C to 150C VES-600-2-C252 -30C to 150C VDE-600-2-C203 VDE-600-2-C28F -46C to 325C
Ball 2" - 24" -46C to 150C
VES-803-2-C2F4 -46C to 150C VES-600-2-C28F -46C to 325C VDE-600-2-C204 VGL-600-1-C201
½" - 1 ½" VES-803-2-C2F5 -46C to 200C VES-600-2-C28G -46C to 400C VDE-600-2-C205 Globe 2" - 12" VGL-600-2-C201 -46C to 345C
Ball -46C to 200C
VES-803-2-C2FA -46C to 325C VES-600-3-C218 Double VDE-600-2-C206 VGL-600-2-C2F1
VES-803-3-C203 -30C to 150C VES-600-3-C219 -30C to 150C Ball ½" - 2" VDE-600-2-C2F1 Plug 2" - 12" VMA-600-2-C201 -30C to 110C
-30C to 150C
VES-803-3-C204 -46C to 150C VES-600-3-C21G VDE-600-2-C2F2 ½" - 1 ½" VRE-800-2-C202 -46C to 345C
VES-803-3-C205 -46C to 200C VES-600-3-C238 VDE-600-2-C2F3 2" - 4" VRE-600-1-C211 0C to 150C
-46C to 150C
VES-803-3-C2F3 -30C to 150C VES-600-3-C239 -46C to 150C VDE-600-2-C2F4 Check VRE-600-2-C212
-46C to 345C
VES-803-3-C2F4 -46C to 150C VES-600-3-C23G VDE-600-2-C2F5 2" - 24" VRE-600-2-C215
-46C to 200C
VES-803-3-C2F5 -46C to 200C VES-600-3-C252 VDE-600-2-C2F6 VRE-600-2-C235 -46C to 210C
-30C to 150C
2" - 24" VES-600-1-C214 -30C to 150C VES-600-3-C253
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24
BRANCH SIZE
Notes
154 Studs, bolts and nuts shall be Zn-Ni coated if the design temperature of the line is up to 260 C. Design temperature abov e 260 C, studs, bolts and nuts shall be bare ty pe (w ithout zn ni coating).
P 4X-001

CS Inconel 600 E30
Clad.
Te mp e rature (°C) -20 0 38 100 150 200
½" - 1 ½" PE
2" - 3"
4" - 10" STD
API 5L Gr X65 PSL 2 (SML or WLD SAW)
Pipes
12" - 14" XS
Pipe -
16" 0.562" BE
T-107 ASME B36.10
18" 0.625"
API 5L Gr X65 PSL 2 WLD SAW
20" 0.688"
24" 0.812"
90 Elbow C01-33
45 Elbow C02-33
Tee C03-33
ASME B16.11
Cross C05-33 ½" - 1 ½"
Cap C11-33
Red Tee C04-33
¾" - 1 ½" ASME B16.11 ASTM B366 (UNS N06625)
Red Coupling C08-33
90 LR Elbow C15-33
45 LR Elbow C16-33
90 SR Elbow C17-33
2" - 3" ASME B16.9
Tee C20-33
Cap C22-33
Fittings
Cross C24-33
C12-33 2" - 4"
Weldolet MSS SP-97
C12-22 2" - 10" ASTM A694 Gr F65
Conc. Red C18-33
Ecc. Red C19-33 3" - 4" ASME B16.9 ASTM B366 (UNS N06625)
Red Tee C21-33
90 LR Elbow C15-22
45 LR Elbow C16-22
90 SR Elbow C17-22
4" - 24"
Tee C20-22
Cap C22-22 MSS SP-75 ASTM A860 WPHY65
Cross C24-22
Conc. Red C18-22
Ecc. Red C19-22 6" - 24"
Red Tee C21-22
PBE
N-C133 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E133 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E433 2" - 3" BLE x PSE
Flanges
F-600-KL 2" - 3"

Welding Neck (WN)
F-600-KC 4" - 24" According to pipe Class 600 Raised Face ASME B16.5 ASTM A694 Gr F65
F-600-LL ½" - 3" ASTM B564 (UNS N06625)
Blind
F-600-LC 4" - 24" ASTM A694 Gr F65
Nuts Gasket
A320 L7, Zn-Ni

Paddles Stud &

A194 7L, Zn-Ni
10" - 24" B16.5 625 layer
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S CS Inconel 600 E30
Clad.
Valv es (see notes)
VAG-3000-1-N102 2" - 4" VES-600-1-C580 0C to 400C VES-600-2-C582 VDE-600-2-N101 -30C to 150C
Needle ½" - 1 ½" -100C to 400C 0C to 400C
VAG-3000-1-N1F2 VES-600-2-C514 VES-600-2-C58G VDE-600-2-N107
-29C to 150C -100C to 400C
VES-801-1-N104 -46C to 150C VES-600-2-C51F VES-600-2-C59F -29C to 200C VDE-600-2-N108
VES-801-1-N105 -100C to 200C VES-600-2-C524 VES-600-3-C553 VDE-600-2-N1F1 -30C to 150C
-29C to 150C ½" - 2"
VES-801-2-N104 -46C to 150C VES-600-2-C528 VES-600-3-C55G VDE-600-2-N1F5
2" - 24" Double -100C to 200C
VES-801-2-N105 -100C to 200C VES-600-2-C534 VES-600-3-C562 VDE-600-2-N1F6
0C to 150C 0C to 210C Ball
VES-801-2-N1F3 VES-600-2-C538 VES-600-3-C563 VDE-600-2-N1F7
½" - 1 ½" -46C to 150C -100C to 400C
VES-801-2-N1F4 VES-600-2-C53F VES-600-3-C572 VDE-600-2-N1F8
Ball Ball
VES-801-2-N1F5 -100C to 200C 2" - 24" VES-600-2-C53G VES-600-3-C573 -29C to 200C VDE-600-2-C515
Ball -29C to 150C
VES-801-2-N1F6 -100C to 340C VES-600-2-C560 VES-600-3-C57G 3" - 8" VDE-600-2-C51F
VES-801-3-N105 VES-600-2-C562 2" - 20" VES-600-3-C582 VDE-600-2-C57F -29C to 200C
-100C to 200C
VES-801-3-N1F5 VES-600-2-C570 VES-600-3-C583 0C to 400C VGL-600-2-C501
0C to 210C 2" - 24" Globe 2" - 12" -29C to 400C
VES-600-1-C524 VES-600-2-C572 VES-600-3-C58G VGL-600-2-C5F1
0C to 150C
VES-600-1-C534 VES-600-2-C57F VES-600-4-C564 ½" - 1 ½" VRE-800-2-N102 -100C to 400C
2" - 4" 0C to 210C
VES-600-1-C560 VES-600-2-C57G 6" - 24" VES-600-4-C574 Check VRE-600-2-C515 -29C to 400C
0C to 210C 2" - 24"
VES-600-1-C570 VES-600-2-C580 0C to 400C VES-600-4-C584 0C to 400C VRE-600-2-C535 -29C to 210C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24
BRANCH SIZE
Notes
138 Welded pipe to API 5L: 100 % RT of w eld seam.
P 4X-001

3.5Ni 600 E32
InconelClad
Te mp e rature (°C) -55 0 38 50 100 150 200 250 300 330
Max Pre ssure (b arg ) 102.1 102.1 102.1 100.2 93.2 90.2 87.6 83.9 79.6 76.9
½" - 1 ½" PE
2" - 3"
4" - 6" STD
Pipes
8" 0.344"
Pipe -
10" 0.438" BE ASTM A333 Gr 3 SML
T-211 ASME B36.10
12" XS
14" 0.562"
16" 0.625" ASTM A333 Gr 3 WLD
90 Elbow C01-33
45 Elbow C02-33
Tee C03-33
ASME B16.11
Cross C05-33 ½" - 1 ½"
Cap C11-33
Red Tee C04-33
¾" - 1 ½" ASME B16.11
Red Coupling C08-33
90 LR Elbow C15-33 ASTM B366 (UNS N06625)
45 LR Elbow C16-33
90 SR Elbow C17-33
2" - 3" ASME B16.9
Tee C20-33
Fittings
Cap C22-33
Cross C24-33
Conc. Red C18-33
Ecc. Red C19-33 3" - 4"
Red Tee C21-33 According to pipe - BE
90 LR Elbow C15-11
45 LR Elbow C16-11
90 SR Elbow C17-11
4" - 16" ASME B16.9
Tee C20-11
Cap C22-11 ASTM A420 Gr WPL3
Cross C24-11
Conc. Red C18-11
Ecc. Red C19-11 6" - 16"
Red Tee C21-11
PBE
N-C133 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E133 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E433 2" - 4" BLE x PSE
Flanges
F-600-KL 2" - 3"

Welding Neck (WN)
F-600-KE 4" - 16" According to pipe Class 600 Raised Face ASME B16.5 ASTM A350 Gr LF3 Cladded
F-600-LL ½" - 3" ASTM B564 (UNS N06625)
Blind
F-600-LE 4" - 16" ASTM A350 Gr LF3 Cladded
Nuts Gasket
A320 L7
Paddles Stud &
Stud and Nuts P-600-02 ½" - 1 ⅛" - - - ASME B1.1

A194 7L
10" - 16" B16.5 625 layer
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S 3.5Ni 600 E32
InconelClad
Valv es (see notes)
VAG-3000-1-N102 VES-600-2-A538 VES-600-3-A583 VDE-600-2-N1F7
Needle ½" - 1 ½" -100C to 400C 2" - 16" -100C to 400C ½" - 2" -100C to 400C
VAG-3000-1-N1F2 VES-600-2-A53F -46C to 150C VES-600-3-A58G VDE-600-2-N1F8
Ball
Butterfly 6" - 16" VBO-600-3-A561 -100C to 345C VES-600-2-A53G VES-600-4-A574 -100C to 200C VDE-600-2-A515
6" - 16" -30C to 150C
VES-801-1-N104 -46C to 150C VES-600-2-A570 VES-600-4-A584 -100C to 400C VDE-600-2-A51F
VES-801-1-N105 -100C to 200C VES-600-2-A572 -100C to 200C VES-600-2-A589 Double VDE-600-2-A53F
Rising - -100C to 340C Ball
VES-801-2-N104 -46C to 150C VES-600-2-A57G Stem VES-600-3-A589 3" - 8" VDE-600-2-A571 -46C to 200C
VES-801-2-N105 -100C to 200C VES-600-2-A580 -100C to 340C VDE-600-2-N105 VDE-600-2-A57F
Ball 2" - 16" -100C to 200C
VES-801-2-N106 -100C to 340C VES-600-2-A582 VDE-600-2-N106 VDE-600-2-A581
½" - 1 ½" -100C to 340C
VES-801-2-N1F4 -46C to 150C VES-600-2-A58F -100C to 400C VDE-600-2-N107 VDE-600-2-A58F
Ball -100C to 400C
VES-801-2-N1F5 -100C to 200C VES-600-2-A58G Double VDE-600-2-N108 VGL-600-2-A501
Ball ½" - 2" Globe 2" - 14" -100C to 345C
VES-801-2-N1F6 -100C to 340C VES-600-3-A572 VDE-600-2-N1F1 -30C to 150C VGL-600-2-A5F1
VES-801-3-N105 VES-600-3-A573 -100C to 200C VDE-600-2-N1F3 -46C to 150C ½" - 1 ½" VRE-800-2-N102
-100C to 200C
VES-801-3-N1F5 VES-600-3-A57G VDE-600-2-N1F5 Check VRE-600-2-A515 -100C to 400C
-100C to 200C 2" - 16"
2" - 4" VES-600-1-A534 VES-600-3-A582 -100C to 400C VDE-600-2-N1F6 VRE-600-2-A535
-46C to 150C
2" - 16" VES-600-2-A534
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16
Notes
P 4X-001

C N I - Corrosive Chemical Injection (Ex cept Sodium Hypochlorite); F G - Fuel Gas; G - Glycol; H - Hydraulic Fluid; P - Process (non-corrosive hydrocarbon); PC - Process (Corrosive
SS 900 F3
Hydrocarbon);
316/316L
Te mp e rature (°C) -100 38 50 100 150 200 250 300 325
Max Pre ssure (b arg ) 148.9 148.9 144.3 126.6 115.5 107.0 100.1 94.9 92.7
S-40S
2" - 3"
4" - 8" S-80S
Pipes
10" 0.594"
Pipe -
T-323 12" 0.688" BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
14" 0.750"
16" 0.844"
18" 1.000"
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Cap C11-43
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Red Coupling C08-43
Fittings

90 LR Elbow C15-44
45 LR Elbow C16-44
90 SR Elbow C17-44
2" - 18"
Tee C20-44
Cross C24-44
Conc. Red C18-44
Ecc. Red C19-44 3" - 18"
Red Tee C21-44
PBE
N-C144 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E144 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E444 2" - 4" BLE x PSE
Socket Weld (SW) F-1500-QX ½" - 1 ½"
Class 1500
F-1500-RX 2"
Welding Neck (WN) Ring Type Joint ASME B16.5
Flanges
F-900-RX 3" - 18" Class 900

F-1500-SX ½" - 2" According to pipe Class 1500 ASTM A182 Gr F316/316L
Blind F-350-4X ½" - 3" max 350 bar - ISO 6162-1
F-900-SX 3" - 18" Class 900 Ring Type Joint ASME B16.5
Nuts Gasket
J-1500-AT ½" - 2" Class 1500

Ring-Joint - Ring Type Joint ASME B16.20 Stainless Steel AISI 316
J-900-AT 3" - 18" Class 900
A320 L7, Zn-Ni
Paddles Stud &
Stud and Nuts P-900-08 ¾" - 1 ⅞" - - - ASME B1.1

A194 7L, Zn-Ni
Figure-8 Blank R8-900-JS ½" - 6"
Paddle Blank RA-900-JS According to pipe 900 Ring Type Joint - Stainless Steel ASTM A240 316
8" - 18" ASME B16.5
Paddle Spacer RE-900-JS
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S SS 900 F3
316/316L
Valv es (see notes)
VAG-3000-1-S201 -100C to 200C VES-900-2-S21G -30C to 150C VES-900-3-S239 VDE-900-2-S2F5
-46C to 150C -100C to 200C
VAG-3000-1-S202 -100C to 400C VES-900-2-S224 VES-900-3-S23G VDE-900-2-S2F6
Needle ½" - 1 ½" 0C to 150C ½" - 2"
VAG-3000-1-S2F1 -100C to 200C VES-900-2-S228 VES-900-3-S252 VDE-900-2-S2F7
-100C to 260C
VAG-3000-1-S2F2 -100C to 400C VES-900-2-S234 VES-900-3-S253 -30C to 150C VDE-900-2-S2F8
Butterfly - VBO-900-3-S269 -100C to 345C VES-900-2-S238 VES-900-3-S25G VDE-900-2-S214
-46C to 150C
VES-1502-1-S206 -30C to 150C VES-900-2-S23F 2" - 18" VES-900-3-S262 Double VDE-900-2-S215 -30C to 150C
0C to 210C
VES-1502-1-S207 -46C to 200C VES-900-2-S23G VES-900-3-S263 Ball VDE-900-2-S21F
Ball
VES-1502-2-S206 -30C to 150C VES-900-2-S250 VES-900-3-S272 -46C to 200C VDE-900-2-S234
3" - 8"
VES-1502-2-S207 -100C to 200C VES-900-2-S252 VES-900-3-S273 VDE-900-2-S235 -46C to 150C
-30C to 150C -100C to 200C
½" - 1 ½" VES-1502-2-S2F1 -100C to 260C VES-900-2-S25F VES-900-3-S27G VDE-900-2-S23F
VES-1502-2-S2F6 -30C to 150C VES-900-2-S25G VES-900-3-S28G -100C to 260C VDE-900-2-S270 -100C to 200C
VES-1502-2-S2F7 -100C to 200C VES-900-2-S260 VES-900-4-S254 -30C to 150C VDE-900-2-S28F -100C to 260C
Ball 2" - 18" 0C to 210C
VES-1502-3-S207 VES-900-2-S262 6" - 18" VES-900-4-S264 0C to 210C ½" - 1 ½" VGA-1501-1-S201
-46C to 200C Gate -46C to 400C
VES-1502-3-S2F7 VES-900-2-S270 VES-900-4-S274 -46C to 200C 2" - 18" VGA-900-1-S231
-100C to 200C
Ball VES-900-1-S214 -30C to 150C VES-900-2-S272 VDE-900-2-S201 2" - 4" VGL-900-1-S201 -46C to 400C
-30C to 150C
VES-900-1-S222 0C to 120C VES-900-2-S27F VDE-900-2-S202 Globe VGL-900-2-S201
-46C to 200C 2" - 14" -100C to 400C
VES-900-1-S224 0C to 150C VES-900-2-S27G VDE-900-2-S203 VGL-900-2-S2F1
-46C to 150C
VES-900-1-S234 -46C to 150C VES-900-2-S28F -100C to 260C VDE-900-2-S204 Plug 2" - 10" VMA-900-2-S201 -30C to 110C
VES-900-1-S250 -30C to 150C VES-900-3-S218 Double ½" - 2" VDE-900-2-S205 VRE-1500-1-S202
2" - 18" -100C to 200C ½" - 1 ½" -100C to 400C
VES-900-1-S260 0C to 210C VES-900-3-S219 -30C to 150C Ball VDE-900-2-S206 VRE-1500-2-S202
VES-900-1-S270 -46C to 200C VES-900-3-S21G VDE-900-2-S2F1 2" - 4" VRE-900-1-S211 0C to 150C
-30C to 150C Check
VES-900-2-S214 VES-900-3-S228 VDE-900-2-S2F2 VRE-900-2-S212
0C to 150C -100C to 260C
VES-900-2-S218 -30C to 150C VES-900-3-S229 VDE-900-2-S2F3 2" - 18" VRE-900-2-S215
-46C to 150C
VES-900-2-S21F VES-900-3-S238 -46C to 150C VDE-900-2-S2F4 VRE-900-2-S235 -46C to 260C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 SOC - Sockolet
BRANCH SIZE
Notes
P 4X-001

C N I - Corrosive Chemical Injection (Ex cept Sodium Hypochlorite); F G - Fuel Gas; G - Glycol; H - Hydraulic Fluid; IA - Instrumentation Air; P - Process (non-corrosive hydrocarbon);
SS 1500 G3
316/316L
Te mp e rature (°C) -100 38 50 100 150 210
Max Pre ssure (b arg ) 248.2 248.2 240.6 211 192.5 176.0
S-80S
2"
3" - 4" 0.438"
6" 0.719"
8" 0.875"
Pipes
Pipe 10" 1.125" -

12" 1.250"
14" 1.406"
16" 1.594"
18" 1.781"
20" 1.969"
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Cap C11-43
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Red Coupling C08-43
Fittings

90 LR Elbow C15-44
45 LR Elbow C16-44
90 SR Elbow C17-44
2" - 20"
Tee C20-44
Cross C24-44
Conc. Red C18-44
Ecc. Red C19-44 3" - 20"
Red Tee C21-44
PBE
N-C144 ¾" - 1 ½"
Nipple
Swage Conc Nipple

N-E144 ¾" - 1 ½" PBE
Swage Ecc Nipple
N-E444 2" - 4" BLE x PSE
Socket Weld (SW) F-1500-QX ½" - 1 ½"
Class 1500 Ring Type Joint ASME B16.5
Flanges
Welding Neck (WN) F-1500-RX 2" - 20"

Blind
F-1500-SX ½" - 20" Class 1500 Ring Type Joint ASME B16.5
Nuts Gasket
Ring-Joint J-1500-AT ½" - 20" - Class 1500 Ring Type Joint ASME B16.20 Stainless Steel AISI 316
A320 L7, Zn-Ni

Paddles Stud &
Stud and Nuts P-1500-08 ¾" - 3" - - - ASME B1.1

A194 7L, Zn-Ni
Figure-8 Blank R8-1500-JS ½" - 6"
Paddle Blank RA-1500-JS According to pipe 1500 Ring Type Joint - Stainless Steel ASTM A240 316
8" - 20" ASME B16.5
Paddle Spacer RE-1500-JS
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S SS 1500 G3
316/316L
Valv es (see notes)
VAG-5000-1-S201 -100C to 200C VES-1500-2-S228 0C to 150C VES-1500-3-S252 VDE-1500-2-S2F5
½" - 2" -100C to 200C
VAG-5000-1-S202 -100C to 400C VES-1500-2-S234 VES-1500-3-S253 -30C to 150C VDE-1500-2-S2F6
Needle ½" - 1 ½"
VAG-5000-1-S2F1 -100C to 200C VES-1500-2-S238 VES-1500-3-S25G VDE-1500-2-S214
-46C to 150C
VAG-5000-1-S2F2 -100C to 400C VES-1500-2-S23F VES-1500-3-S262 VDE-1500-2-S215 -30C to 150C
2" - 20" 0C to 210C
VES-1502-1-S206 -30C to 150C VES-1500-2-S23G VES-1500-3-S263 Double VDE-1500-2-S21F
VES-1502-1-S207 -46C to 200C VES-1500-2-S250 VES-1500-3-S272 Ball VDE-1500-2-S234
3" - 8"
VES-1502-2-S206 -30C to 150C VES-1500-2-S252 Ball VES-1500-3-S273 -100C to 200C VDE-1500-2-S235 -46C to 150C
-30C to 150C
VES-1502-2-S207 -100C to 200C VES-1500-2-S25F VES-1500-3-S27G VDE-1500-2-S23F
½" - 1 ½" VES-1502-2-S2F6 -30C to 150C VES-1500-2-S25G 6" - 20" VES-1500-4-S254 VDE-1500-2-S270
-30C to 150C -100C to 200C
VES-1502-2-S2F7 -100C to 200C VES-1500-2-S260 2" - 20" VES-1500-4-S25U VDE-1500-2-S27F
0C to 210C
VES-1502-2-S2FB -46C to 150C VES-1500-2-S262 VES-1500-4-S264 0C to 210C ½" - 1 ½" VGA-1501-1-S201 -46C to 400C
6" - 20"
VES-1502-3-S207 Ball 2" - 20" VES-1500-2-S270 VES-1500-4-S274 Gate VGA-1500-1-S231 -29C to 400C
-46C to 200C -100C to 200C 2" - 16"
VES-1502-3-S2F7 VES-1500-2-S272 2" - 20" VES-1500-4-S27U VGA-1500-2-S231 -46C to 400C
-100C to 200C
VES-1500-1-S214 -30C to 150C VES-1500-2-S27F VDE-1500-2-S201 VRE-1500-1-S202
Ball -30C to 150C ½" - 1 ½"
VES-1500-1-S224 0C to 150C VES-1500-2-S27G VDE-1500-2-S202 VRE-1500-2-S202
-100C to 400C
VES-1500-1-S234 -46C to 150C VES-1500-3-S218 VDE-1500-2-S203 Check VRE-1500-2-S212
-46C to 150C
VES-1500-1-S250 -30C to 150C VES-1500-3-S219 -30C to 150C VDE-1500-2-S204 2" - 20" VRE-1500-2-S215
VES-1500-1-S260 0C to 210C VES-1500-3-S21G Double ½" - 2" VDE-1500-2-S205 VRE-1500-2-S235 -100C to 210C
-100C to 200C
2" - 20" VES-1500-1-S270 -100C to 200C VES-1500-3-S228 Ball VDE-1500-2-S206 Ax ial VAX-1500-3-S2F1
0C to 150C On-off 12" - 20" -100C to 150C
VES-1500-2-S214 VES-1500-3-S229 VDE-1500-2-S2F1 VGL-1500-2-S201 -46C to 400C
-30C to 150C
VES-1500-2-S218 VES-1500-3-S238 VDE-1500-2-S2F2 VGL-1500-2-S202 -100C to 400C
-30C to 150C
VES-1500-2-S21F VES-1500-3-S239 -46C to 150C VDE-1500-2-S2F3 Globe 2" - 14"
-46C to 150C VGL-1500-2-S2F1 -46C to 400C
VES-1500-2-S21G VES-1500-3-S23G VDE-1500-2-S2F4 VGL-1500-2-S2F2 -100C to 400C
VES-1500-2-S224 0C to 150C
Branch (see notes)
0.5 TEE
0.75 RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20
BRANCH SIZE
Notes
P 4X-001

C N I - Corrosive Chemical Injection (Ex cept Sodium Hypochlorite); F - Safety System and Flare; H - Hydraulic Fluid; P - Process (non-corrosive hydrocarbon); PC - Process
SS 2500 H3
(Corrosive Hydrocarbon);
316/316L
Te mp e rature (°C) -100 100 150
Max Pre ssure (b arg ) 351 351 320.8
1" S-80S
T-322 PE ASME B36.19 ASTM A312 TP 316/316L SML
1 ½" 0.281"
2" 0.344"
3" 0.438"
Pipes
4" 0.531"
Pipe -
6" 0.864"
8" 1.250"
10" - 12" 1.500"
14" 1.750"
16" 2.000"
Weldolet C12-43 1" - 6" MSS SP-97 ASTM A182 Gr F316/316L
90 LR Elbow C15-44
45 LR Elbow C16-44
90 SR Elbow C17-44 1" - 16"
Fittings
Cap C22-44
Cross C24-44 ASME B16.9 ASTM A403 Gr WP316/316L
Red Tee C21-44 1 ½" - 16"
Conc. Red C18-44
Ecc. Red C19-44 2" - 16"
Tee C20-44
Blind F-420-4X 1" - 3" max 420 bar - ISO 6162-2
Compact WN F-2500-UX
1" - 16" According to pipe Class 2500 IX seal ring ISO 27509 ASTM A182 Gr F316/316L
Compact Blind F-2500-VX
Hyd One-Piece Flange F-420-3X 1" - 3" max 420 bar - ISO 6162-2
Ring-Joint J-2500-BT 1" - 16" - Class 2500 Metallic Seal Joint ISO 27509 Stainless Steel AISI 316
A320 L7M, Zn-Ni

P-2500-11
Nuts
Stud and Nuts ½" - 2 ¾" - - - ASME B1.1 A194 7LM, Zn-Ni
P-2500-13 UNS N07718 API6ACRA
Figure-8 Blank R8-2500- 1" - 4"
CS
Paddles
Paddle Blank RA-2500- According to pipe 2500 IX Ring Compact - Stainless Steel ASTM A240 316
CS 6" - 16" flange ISO 27509
Paddle Spacer RE-2500-
CS
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S SS 2500 H3
316/316L
Valv es (see notes)
VAG-6000-1-S201 -100C to 200C 1 ½" VES-2503-3-S2F9 -100C to 200C VES-2510-2-S260 VDE-2510-2-S2F3
0C to 210C -46C to 150C
VAG-6000-1-S202 -100C to 400C VES-2510-2-S214 VES-2510-2-S262 1" - 2" VDE-2510-2-S2F4
Needle 1" - 1 ½"
VAG-6000-1-S2F1 -100C to 200C VES-2510-2-S215 VES-2510-2-S270 VDE-2510-2-S2F5 -100C to 150C
VAG-6000-1-S2F2 -100C to 400C VES-2510-2-S218 VES-2510-2-S272 Double VDE-2510-2-S235
-30C to 150C -100C to 200C Ball -46C to 150C
VES-2502-2-S208 -30C to 150C VES-2510-2-S219 VES-2510-2-S27F VDE-2510-2-S23F
3" - 8"
VES-2502-2-S209 -100C to 200C VES-2510-2-S21F VES-2510-2-S27G VDE-2510-2-S270
-100C to 200C
VES-2502-2-S2F8 -30C to 150C VES-2510-2-S21G VES-2510-3-S252 VDE-2510-2-S27F
Ball 2" - 16"
1" VES-2502-2-S2F9 -100C to 200C VES-2510-2-S224 VES-2510-3-S253 -30C to 150C 1" - 1 ½" VRE-2500-2-S202 -100C to 400C
0C to 150C
VES-2502-2-S2G8 -46C to 150C Ball VES-2510-2-S228 VES-2510-3-S25G 2" - 16" VRE-2510-2-S212 -46C to 210C
2" - 16" Check
VES-2502-3-S209 VES-2510-2-S234 VES-2510-3-S262 VRE-2510-2-S215
-46C to 200C 0C to 210C 2" -100C to 210C
Ball VES-2502-3-S2F9 VES-2510-2-S238 VES-2510-3-S263 VRE-2510-2-S235
-46C to 150C
VES-2503-2-S208 -30C to 150C VES-2510-2-S23F VES-2510-3-S272 Ax ial VAX-2510-3-S2F1
On-off 2" - 16" -100C to 150C
VES-2503-2-S209 -100C to 200C VES-2510-2-S23G VES-2510-3-S273 -100C to 200C
VGL-2510-2-S201 -46C to 400C
VES-2503-2-S2F8 -30C to 150C VES-2510-2-S250 VES-2510-3-S27G VGL-2510-2-S202 -100C to 400C
1 ½"
VES-2503-2-S2F9 -100C to 200C VES-2510-2-S252 VDE-2510-2-S203 Globe 2" - 12"
-30C to 150C -46C to 150C VGL-2510-2-S2F1 -46C to 400C
VES-2503-2-S2G8 -46C to 150C VES-2510-2-S25F Double 1" - 2" VDE-2510-2-S204
Ball VGL-2510-2-S2F2 -100C to 400C
VES-2503-3-S209 -100C to 200C VES-2510-2-S25G VDE-2510-2-S205 -100C to 150C
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14 16 HC - Half Coupling
BRANCH SIZE
SOC - Sockolet
Notes
131 ASME flanges until NPS 12 may be used only for PSV assembly .
P 4X-001

G - Glycol; P - Process (non-corrosive hydrocarbon);
Low T emp 2500 H6
CS
Te mp e rature (°C) -46 180
1" - 1 ½" PE
S-160
2"
3" - 6" XXS ASTM A333 Gr 6 SML
T-105 8" 1.000"
Pipes
Pipe 10" 1.250" - ASME B36.10

BE
12" 1.500"
ASTM A333 Gr 6 WLD
14" 1.625"
16" 1.750"
18" 2.000"
Weldolet C12-04 1" - 8" MSS SP-97 ASTM A350 Gr LF2 Cl 1
90 LR Elbow C15-05
45 LR Elbow C16-05
90 SR Elbow C17-05
1" - 18"
Fittings
Tee C20-05
Cross C24-05
Conc. Red C18-05
Ecc. Red C19-05 1 ½" - 18"
Red Tee C21-05
Straight Nipple N-S237 1" - 1 ½" ASTM A733 ASTM A333 Gr 6
Swage Conc Nipple N-C205 According to pipe - BBE

2" - 4" MSS SP-95 ASTM A420 Gr WPL6
Compact WN F-2500-U3
1" - 18" According to pipe Class 2500 IX seal ring ISO 27509 ASTM A350 Gr LF2 Class 1
Compact Blind F-2500-V3
Ring-Joint J-2500-BT 1" - 18" - Class 2500 Metallic Seal Joint ISO 27509 Stainless Steel AISI 316
A320 L7M, Zn-Ni

Paddles Stud &
Stud and Nuts P-2500-11 ½" - 2 ¾" - - - ASME B1.1

A194 7LM, Zn-Ni
Figure-8 Blank R8-2500-CL 1" - 4"
Paddle Blank RA-2500- IX Ring Compact
CL According to pipe 2500 flange ISO 27509 - Low Temp. Carbon Steel ASTM A516 70 + S5
6" - 18"
CL
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Low T emp 2500 H6
CS
Valv es (see notes)
VAG-6000-1-S201 -100C to 200C VES-2510-2-C234 VES-2510-3-C252 VDE-2510-2-C215
Needle 1" - 1 ½" -30C to 150C -30C to 150C
VAG-6000-1-S202 -100C to 400C VES-2510-2-C238 VES-2510-3-C253 Double 3" - 8" VDE-2510-2-C21F
-46C to 150C
VES-2503-2-C208 -30C to 150C VES-2510-2-C23F Ball 2" - 18" VES-2510-3-C272 Ball VDE-2510-2-C235 -46C to 150C
VES-2503-2-C209 -46C to 200C VES-2510-2-C23G VES-2510-3-C273 -46C to 200C VDE-2510-2-C271 -46C to 200C
VES-2503-2-C2F8 -30C to 150C VES-2510-2-C250 VES-2510-3-C27G VRE-2510-2-C213 -46C to 345C
1" - 1 ½" Ball 2" - 18" -30C to 150C
VES-2503-2-C2F9 VES-2510-2-C252 VDE-2510-2-C203 Check 2" - 18" VRE-2510-2-C215 -46C to 200C
Ball -46C to 150C
VES-2503-3-C209 -46C to 200C VES-2510-2-C270 VDE-2510-2-C204 VRE-2510-2-C235 -46C to 345C
VES-2503-3-C2F9 VES-2510-2-C272 Double 1" - 2" VDE-2510-2-C205 -46C to 200C VGL-2510-2-C201
-46C to 200C Ball Globe 2" - 16" -46C to 345C
VES-2510-2-C214 VES-2510-2-C27F VDE-2510-2-C2F3 VGL-2510-2-C2F1
2" - 18" -30C to 150C -46C to 150C
VES-2510-2-C218 VES-2510-2-C27G VDE-2510-2-C2F4
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14 16 18
Notes
P 4X-001

C N I - Corrosive Chemical Injection (Ex cept Sodium Hypochlorite); D - Diesel; F - Safety System and Flare; IW - De-Aerated Sea Water Injection; P - Process (non-corrosive
Super 2500 H12
hydrocarbon); PC - Process (Corrosive Hydrocarbon);
Duplex
Te mp e rature (°C) -50 115 120 190
Max Pre ssure (b arg ) 410 410 406 360
1" - 1 ½" PE
S-80S
2"
ASTM A790 (UNS S32760) SML
T-303 3" - 4" 0.438"
6" 0.625"
8" 0.812" ASTM A790 (UNS S32760) WLD
Pipes
10" 1.000"
12" 1.250" BE
14" 1.406"
T-304 16" 1.594" ASTM A928 (UNS S32760 Cl 1 or 3) WLD
18" 1.781"
20" 1.969"
24" 2.344"
Weldolet C12-30 1" - 10" MSS SP-97 ASTM A182 Gr F55 (UNS S32760)
90 LR Elbow C15-32
45 LR Elbow C16-32
90 SR Elbow C17-32
1" - 24"
Fittings
Tee C20-32
Cross C24-32
Conc. Red C18-32
Ecc. Red C19-32 1 ½" - 24"
Red Tee C21-32
Straight Nipple N-S231 1" - 1 ½" ASTM A733 ASTM A790 (UNS S32760)

1 ½" - 4" MSS SP-95 ASTM A815 (UNS S32760)
Compact WN F-2500-UH
1" - 24" According to pipe Class 2500 IX seal ring ISO 27509 ASTM A182 Gr F55
Compact Blind F-2500-VH
Ring-Joint J-2500-BU 1" - 24" - Class 2500 Metallic Seal Joint ISO 27509 Duplex , ASTM A182 F51
A320 L7M, Zn-Ni

&
P-2500-11
Paddles Stud
Stud and Nuts ½" - 3 ¼" - - - ASME B1.1 A194 7LM, Zn-Ni
Figure-8 Blank R8-2500-CX 1" - 4"
CX According to pipe 2500 flange ISO 27509 - Superduplex ASTM A240 UNS32760
Paddle Spacer RE-2500- 6" - 24"
CX
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Super 2500 H12
Duplex
Valv es (see notes)
VAG-6000-1-D302 VES-2510-2-D33G -46C to 150C VES-2510-4-D354 VDE-2510-2-D370
Needle 1" - 1 ½" -50C to 150C -30C to 150C Double 3" - 8"
VAG-6000-1-D3F2 VES-2510-2-D350 VES-2510-4-D35U Ball VDE-2510-2-D37F -50C to 200C
VES-2502-2-D308 -30C to 150C VES-2510-2-D352 VES-2510-4-D374 VDE-2510-3-D37F
-30C to 150C Ball 6" - 12"
VES-2502-2-D309 -50C to 200C VES-2510-2-D35F VES-2510-4-D375 Gate 1" - 1 ½" VGA-2501-2-D301 -50C to 150C
-50C to 200C
VES-2502-2-D3F8 -46C to 150C VES-2510-2-D35G VES-2510-4-D37E 1" - 1 ½" VRE-2500-2-D302
-50C to 150C
1" - 1 ½" VES-2502-2-D3F9 -50C to 200C VES-2510-2-D370 VES-2510-4-D37U Check 2" - 18" VRE-2510-2-D315
VES-2502-2-D3G8 -30C to 150C VES-2510-2-D372 VDE-2510-2-D301 -30C to 150C 1" - 18" VRE-2510-2-D335 -50C to 260C
-50C to 200C
VES-2502-3-D309 Ball 2" - 24" VES-2510-2-D37F VDE-2510-2-D304 -46C to 150C VAX-2510-3-D301
-50C to 200C 2" - 24"
VES-2502-3-D3F9 VES-2510-2-D37G VDE-2510-2-D305 -50C to 150C VAX-2510-3-D3F1
Ball 1" - 2"
VES-2510-2-D314 VES-2510-3-D352 VDE-2510-2-D3F3 Ax ial VAX-2510-4-D301
Double -46C to 150C -50C to 150C
VES-2510-2-D318 VES-2510-3-D353 -30C to 150C VDE-2510-2-D3F4 On-off VAX-2510-4-D302
-30C to 150C Ball 14" - 24"
VES-2510-2-D31F VES-2510-3-D35G VDE-2510-2-D3F5 -50C to 150C VAX-2510-4-D3F1
2" - 24" VES-2510-2-D31G VES-2510-3-D372 VDE-2510-2-D315 VAX-2510-4-D3F2
-30C to 150C
VES-2510-2-D334 VES-2510-3-D373 -50C to 200C 3" - 8" VDE-2510-2-D31F VGL-2510-2-D301
Globe 2" - 16" -50C to 150C
VES-2510-2-D338 -46C to 150C VES-2510-3-D37G VDE-2510-2-D33F -46C to 150C VGL-2510-2-D3F1
VES-2510-2-D33F
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 SOC - Sockolet
BRANCH SIZE
Notes
155 Studs ASTM A 320 L7M are recommended for temperatures dow n to -73 °C. For temperature below -73 °C (e.g. depressurization) studs UNS N07718 shall be used.
P 4X-001

P - Process (non-corrosive hydrocarbon); PC - Process (Corrosive Hydrocarbon);
Super 2500 H12P
Duplex
Te mp e rature (°C) -50 38 115
Max Pre ssure (b arg ) 410 410 410
1" - 1 ½" PE
S-80S
2"
T-303 3" - 4" 0.438"
6" 0.625"
Pipes
8" 0.812" ASTM A790 (UNS S32760) WLD

10" 1.000" BE
12" 1.250"
T-304 14" 1.406" ASTM A928 (UNS S32760 Cl 1 or 3) WLD
16" 1.594"
18" 1.781"
90 LR Elbow C15-32
45 LR Elbow C16-32 1" - 3" ASME B16.9 ASTM A815 (UNS S32760)
90 SR Elbow C17-32
Tee C20-32
Cap C22-32 1" - 18"
Cross C24-32
ASME B16.9 ASTM A815 (UNS S32760)
Conc. Red C18-32
1 ½" - 3"
Fittings
Ecc. Red C19-32

Red Tee C21-32 1 ½" - 18"
3D 45 Bend C33-31
5D 45 Bend C34-31
6" - 8" ASTM A790 (UNS S32760)
3D 90 Bend C35-31
5D 90 Bend C36-31
NORSOK M-630 NBE2
3D 45 Bend C33-41
5D 45 Bend C34-41
12" - 18" ASTM A928 (UNS S32760 Cl 1 or 3)
3D 90 Bend C35-41
5D 90 Bend C36-41
Straight Nipple N-S231 1" - 1 ½" According to pipe - BBE ASTM A733 ASTM A790 (UNS S32760)
Compact WN F-2500-UH
1" - 18" According to pipe Class 2500 IX seal ring ISO 27509 ASTM A182 Gr F55
Compact Blind F-2500-VH
Ring-Joint J-2500-BU 1" - 18" - Class 2500 Metallic Seal Joint ISO 27509 Duplex , ASTM A182 F51
A320 L7M, Zn-Ni

&
P-2500-11
Paddles Stud
Stud and Nuts ½" - 2 ¾" - - - ASME B1.1 A194 7LM, Zn-Ni
Figure-8 Blank R8-2500-CX 1" - 4"
CX According to pipe 2500 flange ISO 27509 - Superduplex ASTM A240 UNS32760
Paddle Spacer RE-2500- 6" - 18"
CX
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Super 2500 H12P
Duplex
Valv es (see notes)
VES-2502-2-D308 -30C to 150C VES-2510-2-D33F VES-2510-3-D35G -30C to 150C VDE-2510-2-D305 -50C to 150C
-46C to 150C
VES-2502-2-D309 VES-2510-2-D33G VES-2510-3-D372 VDE-2510-2-D3F1 -30C to 150C
-50C to 200C 2" - 18"
VES-2502-2-D3F9 VES-2510-2-D350 VES-2510-3-D373 -50C to 200C 1" - 2" VDE-2510-2-D3F3
1" - 1 ½" -46C to 150C
VES-2502-2-D3G8 -30C to 150C VES-2510-2-D352 VES-2510-3-D37G VDE-2510-2-D3F4
-30C to 150C
VES-2502-3-D309 VES-2510-2-D35F Ball VES-2510-4-D354 VDE-2510-2-D3F5 -50C to 150C
-50C to 200C -30C to 150C Double
VES-2502-3-D3F9 VES-2510-2-D35G VES-2510-4-D35U VDE-2510-2-D315
Ball Ball 2" - 18" Ball -30C to 150C
VES-2510-2-D314 VES-2510-2-D370 4" - 18" VES-2510-4-D374 VDE-2510-2-D31F
VES-2510-2-D318 VES-2510-2-D372 VES-2510-4-D37E -50C to 200C VDE-2510-2-D33F -46C to 150C
-30C to 150C -50C to 200C 3" - 8"
VES-2510-2-D31F VES-2510-2-D37F VES-2510-4-D37U VDE-2510-2-D370
2" - 18"
VES-2510-2-D31G VES-2510-2-D37G VDE-2510-2-D301 -30C to 150C VDE-2510-2-D37F -50C to 200C
VES-2510-2-D334 VES-2510-3-D352 Double 1" - 2" VDE-2510-2-D303 VDE-2510-3-D37G
-46C to 150C -30C to 150C Ball -46C to 150C
VES-2510-2-D338 VES-2510-3-D353 VDE-2510-2-D304 Gate 1" - 1 ½" VGA-2501-2-D301 -50C to 150C
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14 16 18
Notes
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
77 The max imum allow able reduction of w all thickness shall be taken into consideration for 3D and 5D bends.
139 The TOPSIDE flange connection w ith Riser shall be Sw iv el ty pe according to API SPEC 17D ty pe 17SV. It shall be ev aluated by FEM and customized to fit the hub flange w ith the piping
thickness.
155 Studs ASTM A 320 L7M are recommended for temperatures dow n to -73 °C. For temperature below -73 °C (e.g. depressurization) studs UNS N07718 shall be used.
P 4X-001

IW - De-Aerated Sea Water Injection; PC - Process (Corrosive Hydrocarbon);
CS Inconel 2500 H30
Clad.
Te mp e rature (°C) -20 120
1" - 1 ½" PE
2" - 3"
Pipes
Pipe 4" - 12" S-160 -

BE API 5L Gr X65 PSL 2 (SML or WLD SAW)
T-107 14" 2.000" ASME B36.10
16" - 24" S-160 API 5L Gr X65 PSL 2 WLD SAW
Weldolet C12-33 MSS SP-97
90 LR Elbow C15-33
45 LR Elbow C16-33
90 SR Elbow C17-33 1" - 3" ASTM B366 (UNS N06625)
ASME B16.9
Tee C20-33
Cap C22-33
Cross C24-33
Weldolet C12-22 1" - 10" MSS SP-97 ASTM A694 Gr F65
Conc. Red C18-33
Fittings
Ecc. Red C19-33 1 ½" - 3" ASME B16.9 ASTM B366 (UNS N06625)
Red Tee C21-33
90 LR Elbow C15-22
45 LR Elbow C16-22
90 SR Elbow C17-22
Conc. Red C18-22
Ecc. Red C19-22 4" - 24" MSS SP-75 ASTM A860 WPHY65
Tee C20-22
Red Tee C21-22
Cap C22-22
Cross C24-22
Straight Nipple N-S239 1" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
Nipple

1 ½" - 4" MSS SP-95 ASTM B366 (UNS N06625)
F-2500-UL 1" - 3" ASTM B564 (UNS N06625)
Nuts Gasket Flanges
Compact WN
F-2500-UD 4" - 24" ASTM A694 Gr F65 Cladded
According to pipe Class 2500 IX seal ring ISO 27509
F-2500-VL 1" - 3" ASTM B564 (UNS N06625)
Compact Blind
F-2500-VD 4" - 24" ASTM A694 Gr F65 Cladded
Ring-Joint J-2500-BV 4" - 24" - Class 2500 Metallic Seal Joint ISO 27509 Inconel
A320 L7M, Zn-Ni

Paddles Stud &

A194 7LM, Zn-Ni
Figure-8 Blank R8-2500-CI 1" - 4"
Paddle Blank RA-2500-CI According to pipe 2500 IX Ring Compact - Carbon Steel ASTM A516 GR60 with Inconel
6" - 24" flange ISO 27509 625 layer
Paddle Spacer RE-2500-CI
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S CS Inconel 2500 H30
Clad.
Valv es (see notes)
VAG-6000-1-N102 VES-2510-2-C534 VES-2510-4-C574 Double 3" - 8" VDE-2510-2-C51F -29C to 150C
Needle 1" - 1 ½" -100C to 400C Ball
VAG-6000-1-N1F2 VES-2510-2-C538 VES-2510-4-C575 1" - 1 ½" VRE-2500-1-N102 -100C to 400C
-29C to 150C Ball 4" - 24" -29C to 200C
VES-2502-1-N108 -30C to 120C VES-2510-2-C53F VES-2510-4-C57E
VRE-2510-2-C512
VES-2502-1-N109 -100C to 200C VES-2510-2-C53G VES-2510-4-C57U Check -29C to 150C
2" - 24" VRE-2510-2-C515
VES-2502-2-N108 -30C to 120C VES-2510-2-C570 - VDE-2510-2-N101 -30C to 150C
VRE-2510-2-C535 -29C to 200C
VES-2502-2-N109 -100C to 200C Ball 2" - 24" VES-2510-2-C572 VDE-2510-2-N103
1" - 1 ½" VAX-2510-3-D301
Ball VES-2502-2-N1F8 -30C to 120C VES-2510-2-C57F Double VDE-2510-2-N104 Ax ial 6" - 24" VAX-2510-4-D301 -50C to 150C
VES-2502-2-N1F9 VES-2510-2-C57G -29C to 200C Ball 1" - 2" VDE-2510-2-N1F3
-46C to 150C On-off
VAX-2510-4-D302
VES-2502-3-N109 -100C to 200C VES-2510-3-C572 VDE-2510-2-N1F4
VGL-2510-2-C501
VES-2502-3-N1F9 VES-2510-3-C573 3" - 8" VDE-2510-2-C515 -29C to 150C Globe 2" - 16" -29C to 400C
VGL-2510-2-C5F1
2" - 24" VES-2510-2-C514 -29C to 150C VES-2510-3-C57G
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 SOC - Sockolet
BRANCH SIZE
Notes
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
70 Use this Spec only up to SDV.
138 Welded pipe to API 5L: 100 % RT of w eld seam.
P 4X-001

C N I - Corrosive Chemical Injection (Ex cept Sodium Hypochlorite); P - Process (non-corrosive hydrocarbon); PC - Process (Corrosive Hydrocarbon);
Super 10000 J12
Duplex
Te mp e rature (°C) -50 38 100 120
1" S-80S
PE
1 ½" 0.281"
2" 0.344"
T-303 3" 0.600"
Pipes
4" 0.674"
6" 0.875"
BE
8" 1.250" ASTM A790 (UNS S32760) WLD
10" 1.500"
T-304 12" - 14" 2.000" ASTM A928 (UNS S32760 Cl 1 or 3) WLD
16" 2.250"
90 LR Elbow C15-32
45 LR Elbow C16-32
90 SR Elbow C17-32
1" - 16"
Fittings
Tee C20-32
Cross C24-32
Conc. Red C18-32
Ecc. Red C19-32 1 ½" - 16"
Red Tee C21-32

1 ½" - 4" MSS SP-95 ASTM A815 (UNS S32760)
Flange WN API 6BX F-10000-RH
1" - 16" API 6A ASTM A182 Gr F55
Blind API 6BX F-10000-SH According to pipe API 10000 Ring Type Joint
Flange x female NPT F-10000-TG 1" - 2" - ASTM A182 Gr F51
Ring-Joint J-10000-AU 1" - 16" - API 10000 Ring Type Joint API 6A Duplex , ASTM A182 F51
A320 L7M, Zn-Ni

&
P-10000-11
Paddles Stud
Stud and Nuts ¾" - 1 ¾" - - - ASME B1.1 A194 7LM, Zn-Ni
Paddle Blank RA-10000-
AX 1" - 16" According to pipe API 10000 Ring Joint API 6A - Superduplex ASTM A240 UNS32760
AX
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Super 10000 J12
Duplex
Valv es (see notes)
Ball 1" - 2" VES-10000-2-D334 -50C to 150C VDE-10000-2-D3F3 VGA-10000-3-D311 VRE-10000-2-D325
1" - 2" -50C to 150C 1" - 14" Check 1" - 14" -50C to 120C
VDE-10000-2-D301 -30C to 150C Double VDE-10000-2-D3F5 VGA-10000-3-D31F VRE-10000-2-D335
Ball 3" - 4" Gate -50C to 150C
Double VDE-10000-2-D303 -50C to 150C VDE-10000-2-D371 2" - 14" VGA-10000-4-D311 VGL-10000-2-D301
Ball 1" - 2" -50C to 155C Globe 1" - 6" -50C to 150C
VDE-10000-2-D3F1 3" VDE-10000-2-D37F 1" - 14" VGA-10000-4-D31F VGL-10000-2-D3F1
-30C to 150C
VDE-10000-2-D3F2 Gate 1" - 14" VGA-10000-2-D31F -50C to 150C
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14 16 HC - Half Coupling
BRANCH SIZE
SOC - Sockolet
Notes
P 4X-001

D OH - Carbon Diox ide w/ Hydrocarbon; P - Process (non-corrosive hydrocarbon); PC - Process (Corrosive Hydrocarbon);
Super 10000 J12P
Duplex
Te mp e rature (°C) -50 38 120
Max Pre ssure (b arg ) 620 620 620
1" S-80S
PE
1 ½" 0.281"
2" 0.344"
T-303 3" 0.600"
Pipes
Pipe 4" 0.674" - ASME B36.10/B36.19

6" 0.875" BE
8" 1.250" ASTM A790 (UNS S32760) WLD
10" 1.500"
12" - 14" 2.000"
90 LR Elbow C15-32
45 LR Elbow C16-32 1" - 3" ASME B16.9 ASTM A815 (UNS S32760)
90 SR Elbow C17-32
Tee C20-32
Cap C22-32 1" - 14"
Cross C24-32
ASME B16.9 ASTM A815 (UNS S32760)
Conc. Red C18-32
1 ½" - 3"
Fittings
Ecc. Red C19-32

Red Tee C21-32 1 ½" - 14"
3D 45 Bend C33-31
5D 45 Bend C34-31
6" ASTM A790 (UNS S32760)
3D 90 Bend C35-31
5D 90 Bend C36-31
NORSOK M-630 NBE2
3D 90 Bend C35-41 10" - 14"
3D 45 Bend C33-41
ASTM A928 (UNS S32760 Cl 1 or 3)
5D 45 Bend C34-41 12" - 14"
5D 90 Bend C36-41

2" - 4" MSS SP-95 ASTM A815 (UNS S32760)
Flange WN API 6BX F-10000-RH
1" - 14" API 6A ASTM A182 Gr F55
Blind API 6BX F-10000-SH According to pipe API 10000 Ring Type Joint
Flange x female NPT F-10000-TG 1" - 2" - ASTM A182 Gr F51
Ring-Joint J-10000-AU 1" - 14" - API 10000 Ring Type Joint API 6A Duplex , ASTM A182 F51
A320 L43, Zn-Ni

&
P-10000-09
Paddles Stud
Stud and Nuts ¾" - 1 ¾" - - - ASME B1.1 A194 7L, Zn-Ni
AX
Paddle Spacer RE-10000- 1" - 14" According to pipe API 10000 Ring Joint API 6A - Superduplex ASTM A240 UNS32760
AX
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Super 10000 J12P
Duplex
Valv es (see notes)
Ball 1" - 2" VES-10000-2-D334 -50C to 150C VDE-10000-2-D3F3 VGA-10000-2-D31F Gate 1" - 14" VGA-10000-4-D31F -50C to 150C
1" - 2" -50C to 150C
VDE-10000-2-D301 -30C to 150C Double VDE-10000-2-D3F5 1" - 14" VGA-10000-3-D311 1" - 2" VRE-10000-2-D325
Ball Gate -50C to 150C Check -50C to 120C
Double VDE-10000-2-D303 -50C to 150C VDE-10000-2-D371 VGA-10000-3-D31F 1" - 14" VRE-10000-2-D335
Ball 1" - 2" VDE-10000-2-D3F1
3" - 4"
VDE-10000-2-D37F
-50C to 155C
1 ½" -
VGA-10000-4-D311 Globe 1" - 6" VGL-10000-2-D3F1 -50C to 150C
-30C to 150C 14"
VDE-10000-2-D3F2
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14
BRANCH SIZE HC - Half Coupling
SOC - Sockolet
Notes
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
77 The max imum allow able reduction of w all thickness shall be taken into consideration for 3D and 5D bends.
139 The TOPSIDE flange connection w ith Riser shall be Sw iv el ty pe according to API SPEC 17D ty pe 17SV. It shall be ev aluated by FEM and customized to fit the hub flange w ith the piping
thickness.
P 4X-001

F - Safety System and Flare; P - Process (non-corrosive hydrocarbon); PC - Process (Corrosive Hydrocarbon);
Inconel 10000 J40
Te mp e rature (°C) -100 0 100 155
1" S-80S
PE
1 ½" 0.281"
2" 0.344"
3" 0.438"
Pipes
4" 0.531"
Pipe T-203 - ASME B36.10/B36.19 ASTM B444 Gr 1 (UNS N06625) SML
6" 0.864"
BE
8" 1.062"
10" 1.250"
12" 1.594"
14" 1.781"
90 LR Elbow C15-33
45 LR Elbow C16-33
90 SR Elbow C17-33
1" - 14"
Fittings
Tee C20-33
According to pipe - BE ASTM B366 (UNS N06625)
Cap C22-33 ASME B16.9
Cross C24-33
Conc. Red C18-33
Ecc. Red C19-33 1 ½" - 14"
Red Tee C21-33
Straight Nipple N-S239 1" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)

2" - 4" MSS SP-95 ASTM B366 (UNS N06625)
Flange WN API 6BX F-10000-RL
1" - 14" According to pipe API 10000 Ring Type Joint API 6A ASTM B564 (UNS N06625)
Blind API 6BX F-10000-SL
Ring-Joint J-10000-AV 1" - 14" - API 10000 Ring Type Joint API 6A Inconel
Paddles Stud &
Stud and Nuts P-10000-13 ¾" - 1 ¾" - - - ASME B1.1 UNS N07718 API6ACRA

AI 1" - 14" According to pipe API 10000 Ring Joint API 6A - Carbon Steel ASTM A516 GR60 with Inconel
RE-10000- 625 layer
Paddle Spacer AI
P 4X-001
P IP IN G S P E C IFIC A TION FOR TOP S IDE S Inconel 10000 J40
Valv es (see notes)
VDE-10000-2-N101 VDE-10000-2-N1F2 -30C to 150C Double 3" - 4" VDE-10000-2-N171 Gate 1" - 14" VGA-10000-3-N11F -100C to 155C
-30C to 150C -50C to 155C
VDE-10000-2-N102 VDE-10000-2-N1F3 -100C to 155C Ball 3" VDE-10000-2-N17F VRE-10000-2-N125
Double 1" - 2" Double 1" - 2" Check 1" - 12" -100C to 200C
VDE-10000-2-N103 VDE-10000-2-N1F4 -100C to 150C VGA-10000-2-N111 VRE-10000-2-N135
Ball -100C to 150C Ball
VDE-10000-2-N104 VDE-10000-2-N1G1 Gate 1" - 14" VGA-10000-2-N11F -100C to 155C VGL-10000-2-N101
-46C to 150C Globe 1" - 6" -100C to 150C
VDE-10000-2-N1F1 -30C to 150C VDE-10000-2-N1G2 VGA-10000-3-N111 VGL-10000-2-N1F1
Branch (see notes)
1 TEE
1.5 RTEE TEE
3 WOL RTEE RTEE TEE
1 1.5 2 3 4 6 8 10 12 14
BRANCH SIZE HC - Half Coupling
SOC - Sockolet
Notes
101 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM B 444.
102 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM B 564.
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
ANNEX A – VALVES
(Mandatory)
DISCIPLINE: PIPING
INDEX
A.1. SCOPE .....................................................................................................................................5
A.2. NORMATIVE REFERENCES ...................................................................................................5
A.3. TERMS AND DEFINITIONS .....................................................................................................7
A.4. SYMBOLS AND ABBREVIATED TERMS ...............................................................................9
A.5. VALVE SELECTION GUIDE ..................................................................................................11
A.5.1. INTRODUCTION ..................................................................................................................................................11
A.5.2. VALVE SPECIFICATION LEVEL (VSL) - CLASSIFICATION .............................................................................11
A.5.3. VALVE SPECIFICATION LEVEL (VSL) - REQUIREMENTS ..............................................................................12
A.5.4. VALVE FEATURES AND TYPICAL APLICATIONS ............................................................................................13
A.6. GENERAL DESIGN REQUIREMENTS ..................................................................................15
A.6.1. VALVE ..................................................................................................................................................................15
A.6.2. ACTUATOR ..........................................................................................................................................................22
A.7. SPECIFIC DESIGN REQUIREMENTS ...................................................................................23
A.7.1. BALL VALVE ........................................................................................................................................................23
A.7.2. GATE VALVE .......................................................................................................................................................41
A.7.3. CHECK VALVE ....................................................................................................................................................45
A.7.4. GLOBE VALVE ....................................................................................................................................................48
A.7.5. BUTTERFLY VALVE ............................................................................................................................................50
A.7.6. NON-METALLIC VALVE ......................................................................................................................................54
A.8. MATERIALS & FABRICATION ..............................................................................................55
A.8.1. REQUIREMENTS FOR CASTING OF DUPLEX & SUPERDUPLEX ..................................................................55
A.8.2. COATINGS ...........................................................................................................................................................61
A.8.3. ALTERNATIVE MATERIALS ...............................................................................................................................63
A.9. INSPECTION & TESTING ......................................................................................................65
A.9.1. INSPECTION REQUIREMENTS .........................................................................................................................65
A.9.2. DESIGN VALIDATION .........................................................................................................................................67
A.9.3. FACTORY ACCEPTANCE TEST (FAT) REQUIREMENTS ................................................................................68
A.10. HANDLING, STORING & SHIPPING..................................................................................73
A.11. DOCUMENTATION.............................................................................................................73
A.11.1. DOCUMENTATION FORMATS & QUALITY .....................................................................................................73
A.11.2. DATA BOOK ......................................................................................................................................................74
A.11.3. USER MANUAL .................................................................................................................................................75
A.11.4. DOCUMENTATION OF PRESERVATION, PROTECTION AND PACKING ....................................................75
A.11.5. VALVE CODE ....................................................................................................................................................75
A.12. VALVE DATASHEET - VDS ...............................................................................................84
- Rev. 13 - Page 2 of 84
DISCIPLINE: PIPING
FIGURES
FIGURE A.1 – EXAMPLE OF USE OF DRAIN AND VENT PLUG ............................................................................................................................ 15
FIGURE A.2 – EXAMPLE OF NAMEPLATES WITH INDICATION OF SEAT CONFIGURATION ............................................................................. 22
FIGURE A.3 - LOCATION OF DRAIN AND VENT PORTS ....................................................................................................................................... 24
FIGURE A.4 – BALL TYPE ....................................................................................................................................................................................... 25
FIGURE A.5 – SPE/SR SEAT ASSEMBLY MECHANISM (ILLUSTRATION ON A SOFT BALL VALVE) .................................................................. 27
FIGURE A.6 – DPE SEAT ASSEMBLY MECHANISM (ILLUSTRATION ON A SOFT BALL VALVE) ........................................................................ 27
FIGURE A.7 – DBB FEATURE (REF.: DOUBLE BLOCK AND BLEED - TYPE B OF API 6D) .................................................................................. 28
FIGURE A.8 – DIB-1 FEATURE (REF.: DOUBLE ISOLATION AND BLEED - TYPE B OF API 6D) .......................................................................... 28
FIGURE A.9 – DIB-2 FEATURE (REF.: DOUBLE ISOLATION AND BLEED - TYPE B OF API 6D) .......................................................................... 28
FIGURE A.10 – ILLUSTRATION OF TYPICAL CATEGORY B (TRIPLE OFFSET) SEAT CONFIGURATIONS ........................................................ 52
TABLES
TABLE A.1 – CLASSIFICATION OF ACCUMULATED ENERGY AND HIGH DEMAND VALVES ............................................................................. 12
TABLE A.2 – VALVE SPECIFICATION LEVEL (VSL) CLASSIFICATION ................................................................................................................. 12
TABLE A.3 – VALVE SPECIFICATION LEVEL (VSL) REQUIREMENTS .................................................................................................................. 13
TABLE A.4 - VALVE FEATURES AND TYPICAL APPLICATIONS ........................................................................................................................... 14
TABLE A.5 – MATERIAL CLASSES ......................................................................................................................................................................... 16
TABLE A.6 – BODY MATERIAL, ACCORDING TO MATERIAL CLASS ................................................................................................................... 16
TABLE A.7 – PROCESS FABRICATION FOR BODY MATERIALS ACCORDING TO VSL ...................................................................................... 17
TABLE A.8 – TIGHTNESS CLASS FOR STEM SEALS - FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ......................................................... 18
TABLE A.9 – TIGHTNESS CLASS FOR BODY SEALS - FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ......................................................... 19
TABLE A.10 – TIGHTNESS CLASS FOR STEM (OR SHAFT) SEALS WITH METHANE - FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ...... 19
TABLE A.11 – LEAKAGE FROM BODY SEALS WITH METHANE - FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ........................................ 19
TABLE A.12 – ENDURANCE CLASS ACCORDING VSL CLASSIFICATION ........................................................................................................... 19
TABLE A.13 – TEMPERATURE CLASS OF FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ............................................................................ 19
TABLE A.14 – SIL LEVELS ...................................................................................................................................................................................... 20
TABLE A.15 - STUDS, BOLTS AND NUTS MATERIAL SPECIFICATION ................................................................................................................ 20
TABLE A.16 – ACTUATORS TYPE .......................................................................................................................................................................... 23
TABLE A.17 – DESIGN STANDARDS FOR BALL VALVES ..................................................................................................................................... 26
TABLE A.18 – MOUNTING TYPE FOR BALL VALVES ............................................................................................................................................ 26
TABLE A.19 – ISOLATION VALVE CONFIGURATION FOR BALL VALVES ............................................................................................................ 29
TABLE A.20 – NON-METALLIC MATERIALS FOR SEAT INSERT SEAL DESIGN .................................................................................................. 29
TABLE A.21 – SEAL GROUPS MATERIALS ............................................................................................................................................................ 30
TABLE A.22 – INDICATION OF GROUPS OF SEALS ACCORDING TO FLUID CLASS AND TEMPERATURE RANGE ........................................ 31
TABLE A.23 – SEALS GROUP CLASSIFICATION INTO VALVE CODE .................................................................................................................. 32
TABLE A.24 – NIPPLE CLASSIFICATION INTO VALVE CODE ............................................................................................................................... 32
TABLE A.25 – TYPICAL CONFIGURATIONS FOR BALL METALLIC VALVES UP TO NPS 1 1/2 (“FORGED” VALVES) ........................................ 33
TABLE A.26 – TYPICAL CONFIGURATIONS FOR METALLIC BALL VALVES NPS 2 AND ABOVE AND DOUBLE BALL VALVE NPS 3 AND ABOVE
................................................................................................................................................................................................................................. 35
TABLE A.27 – TYPICAL CONFIGURATIONS FOR RISING STEM BALL VALVES .................................................................................................. 35
TABLE A.28 – TYPICAL CONFIGURATIONS FOR METALLIC DOUBLE BALL VALVES UP TO NPS 2 .................................................................. 36
TABLE A.29 - STEM MATERIALS ACCORDING TO MATERIAL CLASS & PRESSURE CLASS OF THE VALVE ................................................... 37
TABLE A.30 – SPECIFICATION OF METALLIC COATING (PARTIAL CLAD) FOR BALL VALVES ......................................................................... 38
TABLE A.31 – SPECIFICATION OF HARD COATING ON SEATS / BALL ON SOFT BALL VALVES ...................................................................... 38
TABLE A.32 – SPECIFICATION OF HARD COATING ON SEATS / BALL ON METAL-TO-METAL BALL VALVES ................................................. 39
TABLE A.33 – TYPICAL CONFIGURATIONS FOR SOFT SEATED BALL VALVES ACCORDING TO MATERIAL CLASS ..................................... 39
- Rev. 13 - Page 3 of 84
DISCIPLINE: PIPING
TABLE A.34 – TYPICAL CONFIGURATIONS FOR METAL-TO-METAL SEATED BALL VALVES ACCORDING TO MATERIAL CLASS ................ 40
TABLE A.35 – DESIGN STANDARDS FOR GATE VALVES .................................................................................................................................... 43
TABLE A.36 – TRIM MATERIAL CONFIGURATION FOR SOLID WEDGE GATE VALVES ..................................................................................... 43
TABLE A.37 – OBTURATOR TYPE FOR GATE VALVES ........................................................................................................................................ 44
TABLE A.38 – TRIM SELECTION............................................................................................................................................................................. 45
TABLE A.39 – DESIGN STANDARDS FOR CHECK VALVES.................................................................................................................................. 46
TABLE A.40 – SEAL GROUP MATERIALS FOR SOFT SEATED DUAL PLATE CHECK VALVE............................................................................. 46
TABLE A.41 – TRIM MATERIAL ACCORDING TO MATERIAL CLASS.................................................................................................................... 47
TABLE A.42 – OBTURATOR TYPE FOR CHECK VALVES...................................................................................................................................... 48
TABLE A.43 – TRIM SELECTION............................................................................................................................................................................. 48
TABLE A.44 – DESIGN STANDARDS FOR GLOBE VALVES .................................................................................................................................. 48
TABLE A.45 – TRIM DESIGN CODE FOR GLOBE VALVES .................................................................................................................................... 49
TABLE A.46 – OBTURATOR TYPE FOR GLOBE VALVES ...................................................................................................................................... 50
TABLE A.47 – DESIGN STANDARDS FOR BUTTERFLY VALVES ......................................................................................................................... 51
TABLE A.48 – NON-METALLIC MATERIALS FOR SEATS / STEM SEAL DESIGN ................................................................................................. 51
TABLE A.49 – MATERIAL CLASS CONFIGURATION FOR BUTTERFLY VALVES ................................................................................................. 52
TABLE A.50 – DISC & SEAT CONFIGURATION FOR BUTTERFLY VALVES ......................................................................................................... 53
TABLE A.51 – END CONNECTION CONFIGURATION FOR BUTTERFLY VALVES ............................................................................................... 54
TABLE A.52 – MATERIAL CONFIGURATION FOR NON-METALLIC VALVES ........................................................................................................ 54
TABLE A.53 – MINIMUM PRESSURE (PSIG) – TEMPERATURE RATING FOR NON-METALLIC BALL VALVES .................................................. 54
TABLE A.54 – MINIMUM PRESSURE (PSIG) – TEMPERATURE RATING FOR NON-METALLIC CHECK VALVES .............................................. 54
TABLE A.55 – MINIMUM PRESSURE (PSIG) – TEMPERATURE RATING FOR NON-METALLIC BUTTERFLY VALVES ...................................... 55
TABLE A.56 – MINIMUM VALUES FOR TENSION TESTS ...................................................................................................................................... 57
TABLE A.57 - MAXIMUM LEVELS OF SEVERITY BY DEFECT BY THICKNESS .................................................................................................... 59
TABLE A.58 – CHEMICAL COMPOSITION FOR ASTM A522 – TYPE I................................................................................................................... 66
TABLE A.59 – DESIGN VALIDATION REQUIREMENTS ACCORDING VSL CLASSIFICATION.............................................................................. 67
TABLE A.60 – QSL / PSL REQUIREMENT ACCORDING VSL CLASSIFICATION................................................................................................... 70
TABLE A.61 – TIGHTNESS CLASS FOR STEM SEALS - FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ....................................................... 71
TABLE A.62 – TIGHTNESS CLASS FOR BODY SEALS - FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ....................................................... 72
TABLE A.63 – IDENTIFICATION OF BODY MATERIAL CODE, ACCORDING TO RESPECTIVE MATERIAL CLASS ............................................ 80
TABLE A.64 – IDENTIFICATION OF OBTURATOR TYPE, ACCORDING TO VALVE TYPE ................................................................................... 81
TABLE A.65 – IDENTIFICATION OF TRIM DESIGN, ACCORDING TO VALVE TYPE............................................................................................. 82
- Rev. 13 - Page 4 of 84
DISCIPLINE: PIPING
A.1. SCOPE
The scope of this document is related to axial, ball, butterfly, check, diaphragm, gate, globe, needle and plug valves,
either manually actuated or operated by actuators, for use in Exploration and Production (E&P) business area, onshore
and offshore, especially in oil and gas production and their process facilities (topsides and hull).
This document specifies requirements for valves concerning the following topics: design, performance, materials,
manufacturing, testing, inspection, marking, handling, storing, shipment and documentation.
This document is not applicable to control valves. DR-ENGP-I-1.5 addresses main requirements for control valves and
also stablishes supplementary requirements for emergency Shut Down Valves (SDV) and BlowDown Valves (BDV).
The valves considered in this document may be acquired directly by PETROBRAS or through a Contract, as example
EPC (Engineering, Procurement and Construction), in both cases to be used for existing facilities or new projects.
A.2. NORMATIVE REFERENCES

API 594, Check valves: Flanged, Lug, Wafer and Butt-welding
API 598, Valve Inspection and Testing
API 599, Metal Plug Valves-Flanged, Threaded and Welding Ends
API 600, Steel Gate Valves-Flanged and Butt-Welding Ends, Bolted Bonnets
API 602, Steel Gate, Globe and Check Valves for Sizes DN 100 and Smaller for the Petroleum and Natural Gas
Industries
API 603, Corrosion-resistant, Bolted Bonnet Gate Valves—Flanged and Butt-welding Ends
API 607, Fire Test for Quarter-turn Valves and Valves Equipped with Nonmetallic Seats
API 609, Butterfly Valves: Double-flanged, Lug – and Wafer-type
API 6A, Specification for Wellhead and Christmas Tree Equipment
API 6D, Specification for Pipeline and Piping Valves
ASME B 1.1, Unified Inch Screw Threads, UN and UNR Thread Form
ASME B 18.2.1, Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex Flange, Lobed Head, and
Lag Screws (Inch Series)
ASME B 18.2.2, Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange, and Coupling Nuts (Inch
Series)
ASME B 31.3, Process piping
ASME B1.20.1, Pipe Threads, General Purpose (Inch)
ASME B16.1, Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250
ASME B16.10, Face-to-face and end-to-end dimensions of valves
ASME B16.11, Forged fittings, socket-welding and threaded
ASME B16.20, Metallic Gaskets for Pipe Flanges: Ring-Joint, Spiral-Wound, and Jacketed
ASME B16.25, Buttwelding ends
- Rev. 13 - Page 5 of 84
DISCIPLINE: PIPING
ASME B16.34, Valves – Flanged, threaded and welding end
ASME B16.47, Large Diameter Steel Flanges: NPS 26 through NPS 60 Metric/Inch Standard
ASME B16.5, Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard
ASME B31.4, Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids
ASME B31.8, Gas Transmission and Distribution Piping Systems
ASME SA–995–04, Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing Parts
ASME SEC VIII DIV 1 APPENDIX 7, Examination of Steel Castings
ASME SEC VIII DIV 1 SUB A PT UG, General Requirements for All Methods of Construction and All Materials
ASME Section II, Part D, Boiler and Pressure Vessel Code (BPVC), Section II: Materials – Part D: Properties (Metric)
ASME Section VIII, Division 1, Boiler and Pressure Vessel Code (BPVC), Section VIII, Division 1: Rules for Construction
of Pressure Vessels
ASME Section VIII, Division 2, 2004 Edition, Boiler and Pressure Vessel Code, Section VIII, Division 2: Alternative Rules
ASTM A370–05, Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A488 / A488M–04, Steel Castings, Welding, Qualifications of Procedures and Personnel
ASTM A703 /A703M–04A, Steel Castings, General Requirements, for Pressure-Containing Parts
ASTM A781 / A781M–05, Castings, Steel and Alloy, Common Requirements, for General Industrial Use
ASTM A802 / A802M–95, Steel Castings, Surface Acceptance Standards, Visual Examination
ASTM A903 / A903M–99, Steel Castings, Surface Acceptance Standards, Magnetic Particle and Liquid Penetrant
Inspection
ASTM A995 / A995M–98, Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing
Parts
ASTM B584, Specification for copper alloy sand castings for general applications
ASTM B849, Specification for pre-treatments of iron or steel for reducing risk of hydrogen embrittlement
ASTM B850, Standard Guide for post-coating treatments of steel for reducing the risk of hydrogen embrittlement
ASTM E1030–00, Radiograph Examination of Metallic Castings
ASTM E165–02, Test method for Liquid Penetrant Examination
ASTM E186–98, Heavy-Walled (2 to 4 ½-in. [51 to 114-mm]) Steel Castings
ASTM E280–98, Heavy-Walled (4 ½ to 12-in. [114 to 305-mm]) Steel Castings
ASTM E446–98, Steel castings Up to 2 in. [51 mm] in Thickness
ASTM E562–02, Test Method for Determining Volume Fraction by Systematic Manual Point Count
ASTM E94–04, Radiograph Examination
ASTM G48–03, Standard Test Method for Pitting and Crevice Corrosion Resistance of Stainless Steel and Related
Alloys by Use of Ferric Chloride Solution
BS 1868, Specification for steel check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied
industries
- Rev. 13 - Page 6 of 84
DISCIPLINE: PIPING
BS 1873, Specification for steel globe and globe stop and check valves (flanged and butt-welding ends) for the
petroleum, petrochemical and allied industries
BS EN 1226 6-1, Industrial valves – Testing of metallic valves Part 1: Pressure tests, test procedures and acceptance
criteria – Mandatory requirements
BS EN 12266-2, Industrial valves – Testing of metallic valves Part 2: Tests, test procedures and acceptance criteria –
Supplementary requirements
BS ISO 7121, Steel Ball Valves for general purpose Industrial Applications
EN 10204, Metallic products Types of inspection documents
ET-3000.00-1200-956-PCI-001, Código de Cores – Pintura
IOGP S-562, Supplementary Requirements to API Specification 6D Ball Valves
IOGP S-611, Supplementary Requirements to API 600 Steel Gate Valves and to API 603 CRA Gate Valves
ISO 10434, Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries
ISO 10497, Testing of valves – Fire type-testing requirements
ISO 12944-9, Paints and varnishes — Corrosion protection of steel structures by protective paint systems
ISO 14313, Petroleum and natural gas industries – Pipeline transportation systems – Pipeline valves
ISO 15156 (all parts), Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and
gas production
ISO 15761, Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries
ISO 15848-1, Industrial valves - Measurement, test and qualification procedures for fugitive emissions – Part 1:
Classification system and qualification procedures for type testing of valves
ISO 15848-2, Industrial valves - Measurement, test and qualification procedures for fugitive emissions – Part 2:
Production acceptance test of valves
ISO 17292, Metal ball valves for petroleum, petrochemical and allied industries
ISO 5208, Industrial valves – Pressure testing of metallic valves
MSS SP-25, Standard Marking System for Valves, Fittings, Flanges and Unions
MSS SP-45, Bypass and drain connections
MSS SP-55, Quality Standard for Steel Castings for Valves, Flanges, Fittings, and Other Piping Components - Visual
Method for Evaluation of Surface Irregularities
MSS SP-9, Spot facing for bronze, iron and steel flanges
MSS SP-91, Guidelines for manual operation of valves
NBR 15827, Industrial Valves for Installations of Exploration, Production, Refining and Transport of Petroleum Products
- Requirements for Design and Prototype Test
NORSOK 630 Rev. 3/2004, Material Datasheet for Piping
A.3. TERMS AND DEFINITIONS

For the purposes of this document, the following terms and definitions apply:
- Rev. 13 - Page 7 of 84
DISCIPLINE: PIPING
A.3.1. BI-DIRECTIONAL VALVE:
Valve designed for blocking the fluid in both downstream and upstream directions.
A.3.2. CASTING CRITICAL AREAS:
The regions of castings determined by manufacturer engineering, based on valve parts highly stressed by manufacturing
process and as determined by finite elements under the maximum process/operating conditions.
A.3.3. DOUBLE-BLOCK-AND-BLEED VALVE – DBB:
Single valve with two seating surfaces that, in the closed position, provides a seal against pressure from both ends of
the valve with a means of venting/bleeding the cavity between the seating surfaces.
A.3.4. DOUBLE-ISOLATION-AND-BLEED VALVE - DIB:
Single valve with two seating surfaces, each of which, in the closed position, provides a seal against pressure from a
single source, with a means of venting/bleeding the cavity between the seating surfaces.
DIB-1 valves have both seats bidirectional. Vent or relief of valve cavity shall be obtained by use of an external relief
valve.
DIB-2 valves have one seat unidirectional and one seat bidirectional. Further details are listed in A.7.1.4.
A.3.5. THROUGH-CONDUIT VALVE:
Valve with an uninterrupted and continuous cylindrical opening. Consequently, there are no cavities or large gaps in the
bore between seats and body closures or between seats and obturator.
A.3.6. FULL-BORE VALVE:
Valve with an unobstructed opening, not smaller than the internal bore of the end connections.
A.3.7. SEATING SURFACES:
Contact surfaces of the obturator and seat which ensure valve sealing.
A.3.8. PRESSURE CLASS:
Numerical pressure design class, expressed in accordance with either the nominal pressure (PN) class or the ASME
rating class.
A.3.9. PITTING RESISTANCE EQUIVALENT NUMBER (PREN):
Empiric Mathematical Formula that correlates pitting corrosion resistance with the amounts alloying elements in the steel
that contribute to increase this resistance. For duplex steels it shall be calculated as follows:
PREN = %Cr + 3,3 x (%Mo + 0,5 x %W) + 16 x %N.
A.3.10. PILOT CASTING:
For the customer purpose, any casting that is the first of its model or of a new or modified project, using the same casting
procedure (same casting) as the ones it represents.
A.3.11. CASTING:
Any component of a valve, made by casting.
- Rev. 13 - Page 8 of 84
DISCIPLINE: PIPING
A.3.12. NOMINAL TORQUE OF OPERATION – TNO:
It is the actual value of torque needed to operate the valve, under any operation condition. This value shall be presented
in the marking (plate) of the valve.
A.3.13. MAXIMUM TORQUE OF OPERATION – TMO:
It is the maximum value of torque that may be applied on the valve, without damaging the override mechanism (i.e.: no
plastic deformation on the drive train). This value of torque shall present the safety margin of the actuator, to be applied
only under special situation such as a contingency (e.g.: when the valve is not opening / closing with TNO value).
Typically, TMO is 150% TNO.
A.3.14. MAXIMUM ALLOWABLE TORQUE – TMA:
It is the value of torque that may be applied on the valve, after that it shall start damaging the override mechanism (i.e.:
plastic deformation on the drive train).
A.4. SYMBOLS AND ABBREVIATED TERMS

ADV anti-columning deluge valve
CRA corrosion resistance alloy
DBB double block and bleed
DIB-1 double isolation and bleed. Both seats bidirectional (DPE)
DIB-2 double isolation and bleed. One seat uni-directional (SPE or SR) and one seat bidirectional (DPE)
DN nominal size
DPE double piston effect
EPC engineering, procurement and construction
FAT factory acceptance test
HIPPS high integrity pressure protection system
HP high pressure
HVOF high velocity oxygen fuel
ID internal diameter
ITP inspection and testing plan
LCF contractual list of supply
LP low pressure
LPI liquid penetrant inspection
LTD designation for limited class valves per ASME B16.34
MWP maximum working pressure
NDT nondestructive testing
NPS nominal pipe size
- Rev. 13 - Page 9 of 84
DISCIPLINE: PIPING
PFD probability of failure on demand
PST partial stroke testing
PVT performance verification test
QSL quality specification level
RGD rapid gas decompression
SDV shut down valve
SIF safety instrumented function
SIL safety integrity level
SIP shut in pressure
SPE single piston effect
SR self-relief
TMA maximum allowable torque
TMO maximum torque of operation
TNO nominal torque of operation
UNS unified numbering system
VAC axial control valve
VAG needle valve
VAX axial valve
VBO butterfly valve
VCI volatile corrosion inhibitor
VDE double ball valve
VDI diaphragm valve
VDS valve datasheet
VES ball valve
VGA gate valve
VGL globe valve
VMA plug valve
VRE check valve
VSL valve specification level
WPS welding procedure specifications
WPQR welding performance qualification record
- Rev. 13 - Page 10 of 84
DISCIPLINE: PIPING
A.5. VALVE SELECTION GUIDE

A.5.1. INTRODUCTION
A.5.1.1. In this item is presented general information, such as a guide of how shall be conducted the engineering process
to select a valve for use in the Project and/or specific application.
A.5.1.2. The indication of all valves shall be driven by the definition of Valve Specification Level (VSL), which regulates
the specification of an adequate valve for a certain application, taking into account the criticality foreseen in the
application/use of the valve.
A.5.1.3. The VSL classification will provide specific requirements for four valve specification levels (VSLs): VSL-1,
VSL- 2, VSL-3, VSL-4. These four VSL designations define different levels of technical / quality requirements.
A.5.1.4. The determination of the VSL is obtained by the classification rules stated on item A.5.2.
A.5.1.5. All VDS presented herein are formulated according its specific VSL indication. Design premises, such as
materials (metallic / non-metallic), configurations, tests and design validation are based on the criticality foreseen in the
application/use of the valve and defined by the specific VSL.
A.5.1.6. For any given VSL, there is a set of requirements associated with it (item A.5.3).
A.5.1.7. The manufacturer of the valve shall attend all requirements listed in the VDS, including the specific requirements
of VSL.
A.5.1.8. It is possible to have more than one type of valve (e.g.: ball, gate, etc.) with the same VSL number, and possibly
both types would be able to attend a certain application. In this case, it shall be conducted by the Project and/or user an
evaluation of the valve features associated with the foreseen application, and so define the type of valve that shall be
specified in the Project and/or specific application.
A.5.1.9. The valve’s features are presented in item A.5.4, and allows an adequate understanding about which type of
valve is more suitable for the intended application.
A.5.2. VALVE SPECIFICATION LEVEL (VSL) - CLASSIFICATION

The VSL classification shall be taken according to premises indicated in this item. It shall be evaluated the following
parameters by the Project and/or user:
Table A.2 describes this evaluation.
a) Table A.2 describes this evaluation.
b) Accumulated energy: it shall be verified the classification of accumulated energy associated with the use of the
valve, as described in Table A.1.
c) Demand: the expected number of cycles during the lifetime of the valve shall be taken into account when
considering the VSL. The higher the number, the higher the VSL, as described in Table A.1.
- Rev. 13 - Page 11 of 84
DISCIPLINE: PIPING
Table A.1 – Classification of accumulated energy and high demand valves
Valves of Pressure Class 600 and 900, NPS ≥ 6

High
Accumulated Valves of Pressure Class 1500, 2500 and 10.000psi
Energy Valves of Pressure Class 125, 150 and 300
Low
Valves of Pressure Class 600 and 900, NPS ≤ 4
Actuated Filter valves, Actuated XVs, Actuated molecular sieve valve. In

High Demand
general, actuated valves that operate more than once a month.
Table A.2 – Valve Specification Level (VSL) classification
Application Level
HIPPS, SDV Platform limits VSL-4

Safety Valves
SDV, BDV, L/R PIG (Note 1) VSL-3
ADV, ADV Block VSL-2
High Demand
Service (Note 2) Accumulated Energy
Yes No
Hydrocarbon
Hot water High
Flammable VSL-3 VSL-2
Steam Low
Toxic
High VSL-2
Other valves Other services VSL-2
Low VSL-1
Note 1 – This table is not applicable for valves in tubing specifications.
Note 2 – See below the fluids belonging to each service:
- Hydrocarbon / Flammable / Toxic: AM, CI, CI2, CN, CNI, D, DF, DFC, DOH, F, FG, G, GL,
H, HBG, IGN, JF, OL, P, PC, PCG, PLD, TR;
- Hot water: HWP;
- Steam: S;
- Other services: ADW, AO, BG, BR, BWG, BWH, CHW, CV, DA, DO, DTH, DW, EG, FL,
FLC, FP, FW, GW, HF, HBG, HWU, IA, IG, IN, IW, IWC, PCW, PW, PWH, SA, SC, SFW,
SN, SP, STA, SW, TC, TL, W, WW.
A.5.3. VALVE SPECIFICATION LEVEL (VSL) - REQUIREMENTS
A.5.3.1. Each VSL classification inputs to the valve design a basic information about which API 6D - Quality Specification
Level (QSL) shall be fulfilled, plus a sort of specific requirements (mandatory).
A.5.3.2. The QSL classification and requirements are according to API 6D: QSL-1, QSL-2, QSL-3 or QSL-4. All
requirements listed in API 6D Annex I shall be attended according the respective QSL related to the VSL.
A.5.3.3. The QSL refers to specific requirements for NDT, pressure testing and documentation of the valve.
A.5.3.4. The VSL requirements shall be as described in Table A.3:
- Rev. 13 - Page 12 of 84
DISCIPLINE: PIPING
Table A.3 – Valve Specification Level (VSL) requirements
VSL-2 (not for VSL-2 (with

VSL Requirements VSL-1 VSL-3 VSL-4
hydrocarbon) hydrocarbon)
QSL
QSL-2 QSL-2 QSL-3 QSL-3 QSL-4
(According API 6D)
PSL PSL-3 or PSL-3G PSL-3 or PSL-3G as

NA PSL-4 PSL-4
(According API 6A) as applicable applicable
Fugitive Emissions
Design No No (Note 2) Yes / No (Note 1) Yes / No (Note 1) Yes / No (Note 1)
(According item A.6.1.6)
Fire Resistant
No
(According item Yes / No (Note 3) Yes / No (Note 3) Yes / No (Note 4) Yes
(Note 2)
A.6.1.3.3)
Design Validation
No Design analytical approval Design validation test approval (PVT)
(According item A.9.2)
SIL Capable
No No No No Yes / No (Note 5)
(According item A.6.1.7)
Note 1 – The valve design shall be fugitive emissions approved if the valve will be specified for use in a process pipe that fluid contains
volatile organic compounds (e.g.: benzene), and its emissions to environment are limited by a reglementary law.
Note 2 – If fire resistant requirement is requested by the Project, it shall be considered the use of a VSL-2 valve.
Note 3 – Indication of fire-resistant valve shall be taken according design premises.
Note 4 – SDV, BDV, ADV valves and valves certified for fugitive emissions shall be fire tested. For other valves, indication of fire-tested
valve shall be taken according to design premises.
Note 5 – SIL capable applies only for HIPPS valve.
A.5.4. VALVE FEATURES AND TYPICAL APLICATIONS
A.5.4.1. For each type of valve, Table A.4 presents a summary of valve features and typical applications.
- Rev. 13 - Page 13 of 84
Ball Gate Check Globe Butterfly
Features M etal Rising Stem
Axial Plug Needle Diaphragm
Solid Axial Chamfer Category A Cate gory B Cate gory B
Soft to (Metal to Expanding Slab Piston Dual Plate Swing
We dge (Non-slam) Disc (concentric) (bi-offset) (tri-offset)
M etal M etal)
Manual operator design

A A A A A A N/A N/A N/A N/A A A A A A A A N/A
(eg.: wrench, handwheel gearbox)
Actuated design
A A A A A A N/A N/A N/A N/A A A A A A A N/A A
(e.g.: hydraulic, electric, pneumatic)
Soft seated design Yes No N/A No A No No A No A No Yes Yes No Yes Yes No Yes
Metal to Metal seat design No Yes Yes Yes A Yes Yes A Yes A Yes No No Yes Yes No Yes No
Piggable Yes Yes No No Yes Yes No No N/A No No No No No No No No No

DISCIPLINE: PIPING
Bidirectional Yes Yes No Yes Yes Yes No No No No No No No No Yes Yes No No
Double block and bleed

A A No No A No No No No No No No No No No A No No
(i.e.: DBB)
Double isolation and bleed

A A No No No No No No No No No No No No No No No No
(i.e.: DIB-1, DIB-2)
Fire tested design A A Yes N/A A N/A N/A N/A N/A N/A N/A No A A A A N/A No
- Rev. 13 -
Fire safe design N/A N/A N/A A N/A A A A A A A No N/A N/A N/A N/A A No
Fugitive emissions design Yes Yes Yes Yes Yes Yes N/A N/A N/A N/A Yes Yes Yes Yes Yes Yes Yes Yes
Fit to control application N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A P N/A N/A N/A Yes N/A P N/A
Fit to abrasive service (solids in

N/A P ALT N/A N/A ALT N/A N/A N/A N/A N/A N/A N/A ALT ALT N/A N/A N/A
suspension)
Fit to Safety Instrumented System (SIS)

N/R P N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R ALT N/R N/R N/R
(e.g.: HIPPS application)
SIL capable design N/A A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A A N/A N/A N/A
Table A.4 - Valve features and typical applications
Fit to SDV Platform Limits N/R P N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R
Fit to SDV, BDV application

N/R A N/R N/R N/R A N/R N/R N/R N/R N/R N/R N/R A A N/R N/R N/R
(Hydrocarbon service)
Fit to SDV, BDV application

A A N/R N/R N/R A N/R N/R N/R N/R N/R N/R N/R A A N/R N/R N/R
(Non-hydrocarbon service)
Fit to L/R PIG application N/R A N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R
Fit to molecular sieve application N/R N/R P N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R ALT N/R N/R N/R N/R
Fit to ADV application N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R A N/R N/R N/R N/R A
Legend: A – Available; ALT – Alternative solution; P – Preferential solution; N/R – Not Recommended; N/A - Not Available
Page 14 of 84
DISCIPLINE: PIPING
A.6. GENERAL DESIGN REQUIREMENTS

A.6.1. VALVE
A.6.1.1. GENERAL
A.6.1.1.1. Regarding documentation hierarchy, valve design shall be according to the Standard referenced in the VDS.
In case of conflict between the requirements herein stablished and that Standard, the attendance of this document shall
be considered as mandatory.
A.6.1.1.2. The valve design shall attend all quality, functional, materials, testing, and configuration requirements
specified in the VDS.
A.6.1.1.3. The assembly of the valve / actuator shall meet all operating conditions, in any position of installation, without
performance reduction. Unless clearly specified, it shall be able to operate under full rated condition, such as opening
and closing at full differential pressure, according to the design pressure indicated in the VDS.
A.6.1.1.4. For a heavy weighted valve (Weight > 25 kg) or a valve with larger dimensions (L+W+H > 1500 mm), the
corresponding design shall consider the use at least of four (4) lifting handles. The vertical line of the lifting points shall
be left free to avoid interference with the drive system or actuator.
A.6.1.1.5. The manufacturer shall present all dimensional drawings of the valve and actuator, with a list of all parts and
materials specifications.
A.6.1.1.6. The manufacturer shall present a list of required torques on the valve shaft, containing the following values
of torque: Nominal Torque of Operation (TNO), Maximum Torque of Operation (TMO) and Maximum Allowable Torque
(TMA), taking into account the pressure class of the valve and temperature limits.
Note: for gate and globe valves with manual actuation, TNO shall be according MSS SP-91; for ball valves, the TNO
shall comply with API 6D; and for butterfly valves, the TNO shall be according to API 609.
A.6.1.1.7. The manufacturer shall inform in the documentation all design and/or operation constraints (e.g.: installation
position, flow direction, flow rate, limits of pressure, temperature and metallic / non-metallic materials, etc.).
A.6.1.1.8. Valve ID (bore) shall be compatible with the ID of the pipes and accessories in which the valve is installed.
A.6.1.1.9. All metallic materials shall have a mill certification, with registers of chemical composition, mechanical
properties and other standards requirements, besides the manufacturer batch identification.
A.6.1.1.10. For valve designs which allows retained pressure in body cavity (when valve is fully closed or fully open),
plugs capable to mitigate risk of an accident under an eventual remotion shall be used. In this case, those ports shall be
closed with plugs having a constructive configuration that allows pressure relieving to atmosphere (relief hole) during
the beginning of plug remotion, serving as an alert to the operator about the remaining pressure inside the valve body.
An example of this kind of configuration is showed as follows:
Figure A.1 – Example of use of drain and vent plug
- Rev. 13 - Page 15 of 84
DISCIPLINE: PIPING
A.6.1.2. MATERIAL CLASSES
A.6.1.2.1. The design of the valves shall attend one of the following classifications of material classes:
Table A.5 – Material classes
# Material Class
C Carbon Steel
A Alloy Steel
S Stainless Steel
D Duplex Steel
N Nickel Alloy
U Uncommon materials
A.6.1.3. BODY MATERIAL
A.6.1.3.1. The referred letter of the material class of the valve, shown on the first column of Table A.5, associated with
the number indicated in the lines of Table A.6, gives the body material considered in the valve design. The combination
of the letter and number shall be considered as a part of the valve code, according to description of valve code presented
on item A.11.5.
Table A.6 – Body material, according to material class
Material Class
Body C A S D N U
Material Stainless Uncommon
Carbon steel Alloy steel Duplex steel Nickel alloys
steel materials
ASTM A182
ASTM A105 ASTM A350 LF3 Gr. F304
Alloy 625
1 or or or ASTM A995 Gr. 1B
(UNS N06625)
Bronze
ASTM A216 WCB ASTM 352 LC3 ASTM A351
Gr. CF8
ASTM A182
ASTM A182 Gr.
A350 LF2 CL1 Gr. F316
F51 Ductile iron
2 or ASTM A182 F5 or
or
-
ASTM A536-65-45-12
ASTM A352 LCC ASTM A351
ASTM A995 Gr. 4A
Gr. CF8M
ASTM A105
or ASTM A182
Gr. F317 ASTM A182 Gr.
ASTM A216 WCB ASTM A182 F11 ASTM B148
3 + CL2
or F55 or -
(UNS C95800)
ASTM A351 ASTM A995 Gr 6A
Organic Coating Gr. CG8M
(Onshore use only)
ASTM A105
or ASTM A182
Gr. F347
ASTM A216 WCB
4 +
ASTM A522 Type I or - - Plastics
ASTM A351
Organic Coating Gr. CF8C
(Offshore)
ASTM A105 ASTM A350 LF3
or or
5 ASTM A216 WCB ASTM A352 LC3
- - - Gray Iron
+ +
- Rev. 13 - Page 16 of 84
DISCIPLINE: PIPING
Material Class
Body C A S D N U
Material Stainless Uncommon
Carbon steel Alloy steel Duplex steel Nickel alloys
steel materials
Full Clad Alloy 625 Full Clad Alloy 625
overlay overlay
(UNS N06625) (UNS N06625)
ASTM A350 LF2
CL1
ASTM A522 Type I
or
+ Ductile iron + PFA
ASTM A352 LCC
6 +
Full Clad Alloy 625 - - - liner
overlay ASTM A395 60-40-18
Full Clad Alloy 625
(UNS N06625)
overlay
(UNS N06625)
7 ASTM A694 F65 a - - - - -

ASTM A216 WCB +
8 PTFE / PFA
a
See A.6.1.3.3.
A.6.1.3.2. The use of forgings or castings for the body material shall follow the following classification according the
VSL of the valve, and indicated in the VDS:
Table A.7 – Process fabrication for body materials according to VSL
Pressure Class
VSL
150 300 600 900 1500 2500 10000
VSL-1
Forging or Casting Forging (Note 1)
VSL-2
VSL-3
Forging (Note 1)
VSL-4
Note 1 - Except for axial valves (VAX, VAC) and Triple Offset Butterfly valves made of
NIAlBr (UNS C95800), for which casting is acceptable.
A.6.1.3.3. ASTM A694 forgings shall comply with MDS IX-124 of IOGP S-563 and following modifications:
Acceptance criteria for impact testing on full-size specimens shall be 40 J (average of three specimens)
and 34 J minimum;
Mechanical test specimens shall be taken from mid-thickness and mid-length of the test forging;
Test forging shall be at least the same thickness of production forging;
For cladded valves ultrasonic testing shall be applied after cladding to all forgings. The testing shall be
carried out using both compression and shear wave (normal and angle beam) techniques as per ASTM A388 and
dedicated procedure with scanning plan. Supplementary requirements S1 shall apply. Acceptance criteria shall be as
follows:
No single indication equal to or exceeding reference distance amplitude curve is allowed.
All indication with an echo greater than 25% of the reference will be deemed relevant and shall be
investigated.
No multiple indications exceeding 50% of reference distance amplitude curve is allowed. Multiple
indications are defined as two or more indications (each exceeding 50% of the reference distance amplitude curve)
within 13 mm of each other in any direction.
- Rev. 13 - Page 17 of 84
DISCIPLINE: PIPING
A.6.1.4. FIRE TESTED VALVES
A.6.1.4.1. In order to obtain indication that the valve design shall be fire tested type, it shall be fulfilled all requirements
listed in DR-ENGP-I-1.3, such as the execution of the “Risk Assessment and Safety Studies” (item 5 of DR-ENGP-I-1.3)
and the “Consequence Analysis - (fire propagation, gas dispersion, explosion, etc.)”.
A.6.1.4.2. Whenever specified in the VDS that the valve shall be fire tested, its design shall be submitted to a
certification by testing a prototype according to ISO 10497, API 6FA or API 607 (except 4th edition).
A.6.1.4.3. The manufacturer shall present to PETROBRAS the correspondent certificate and the valve shall be marked
as described on item A.6.1.10.
A.6.1.4.4. The design of the seals on seats/body and stem areas shall consider mandatory the use of a metallic element
or an element made by graphite, to guarantee the attendance of the fire testing requirement. This element shall be
installed on each leakage path of the valve.
A.6.1.5. FIRE SAFE VALVES
A.6.1.5.1. In order to obtain indication that a valve design shall be fire safe type, it shall be fulfilled all requirements
listed in DR-ENGP-I-1.3, such as the execution of the “Risk Assessment and Safety Studies” (item 5 of DR-ENGP-I-1.3)
and the “Consequence Analysis - (fire propagation, gas dispersion, explosion, etc.)”.
A.6.1.5.2. Whenever specified in the VDS that the valve shall be fire safe, its design shall contain material specification
applying materials that are capable of withstanding exposure to fire without failure.
A.6.1.5.3. The fire safe design does not require valve certification, but it shall guarantee that the valve design is resistant
to a fire scenario.
A.6.1.5.4. The design of the seals on seats/body and stem areas shall consider mandatory the use only of a metallic
element or an element made by graphite, to guarantee the attendance of the fire safe requirement.
A.6.1.6. FUGITIVE EMISSIONS
A.6.1.6.1. In order to prevent a failure on a valve (e.g.: leaking toxic fluid to external environment), that could contribute
to the minimize safety to personnel, installation and/or environment, some valves shall be designed to be fugitive
emissions approved. This is applicable to all valves with one of the following services: FG, GL, P or PC.
A.6.1.6.2. Whenever specified in the VDS that the valve shall be fugitive emission approved, its design shall be certified
according to ISO 15848 Part 1, by prototype approval to confirm that an adequate design of seals (on body joints and
stem) is provided.
A.6.1.6.3. The manufacturer shall prepare specific Performance Verification Test (PVT) procedure, according to ISO
15848 Part 1, and submit for PETROBRAS approval.
A.6.1.6.4. The manufacturer shall provide the certificate of approval containing information about the design
“Performance Class” according to ISO 15848 Part 1. Information about “Tightness Class”, “Endurance Class”, and
“Temperature Class” shall be presented in detail.
A.6.1.6.5. The “Tightness Class” shall be according BH.
Table A.8 – Tightness class for stem seals - fugitive emissions (ref.: ISO 15848 Part 1)
Measured leak Measured leak Measured leak

Class Remarks
rate (mass flow) rate (mass flow) rate (volumetric flow)
- Rev. 13 - Page 18 of 84
DISCIPLINE: PIPING
mg.s-1.m-1 stem mg.s-1.m-1 stem mbar.l.s-1 per mm

perimeter diameter through stem diameter through
(for information) stem seal system stem seal system
Typically achieved with bellow seals
AH 1 ≤ 10-5 ≤ 3,14.10-8 ≤ 1,78.10-7 or equivalent stem (shaft) sealing
system for quarter turn valves
Typically achieved with PTFE
BH 2 ≤ 10-4 ≤ 3,14.10-7 ≤ 1,78.10-6 based packings or elastomeric
seals
Typically achieved with flexible
CH 2 ≤ 10-2 ≤ 3,14.10-5 ≤ 1,78.10-4 graphite based packings
1
Expressed by the vacuum method as defined in ISO 15848 Part 1 - Annex A.
2
Measured by the total leak rate measurement method (vacuum or bagging) as defined in ISO 15848 Part 1 - Annex A.
Table A.9 – Tightness class for body seals - fugitive emissions (ref.: ISO 15848 Part 1)
Measured leakage
≤ 50 1
(Body seals)
1
Expressed in ppmv measured with the sniffing method as defined in
ISO 15848 Part 1 - Annex B
Table A.10 – Tightness class for stem (or shaft) seals with methane - fugitive emissions (ref.: ISO 15848 Part 1)
Measured leakage ppmv

Class
(sniffing method according to ISO 15848 Part 1 - Annex B)
AM ≤ 50
BM ≤ 100
CM ≤ 500
1
Expressed in ppmv measured with the sniffing method as defined in ISO 15848 Part 1 - Annex B
Table A.11 – Leakage from body seals with methane - fugitive emissions (ref.: ISO 15848 Part 1)
Measured leakage ppmv

(sniffing method according to ISO 15848 Part 1 - Annex B)
≤ 50
A.6.1.6.6. The mechanical cycles shall be performed according to ISO 15848 Part 1, considering the following
“Endurance Class” x VSL:
Table A.12 – Endurance class according VSL classification
VSL-1 VSL-2 VSL-3 VSL-4

Endurance Class
(as defined in ISO 15848 Part 1 - Annex B)
CC1 / CO1
A.6.1.6.7. The “Temperature Class” shall be tRT. Nevertheless, seal materials shall be suitable for the entire
temperature range informed in the valve data sheet.
Table A.13 – Temperature class of fugitive emissions (ref.: ISO 15848 Part 1)
(t-196 ºC) (t-46 ºC)’ (tRT) (t200 ºC) (t400 ºC)
- Rev. 13 - Page 19 of 84
DISCIPLINE: PIPING
-196 ºC -46 ºC Room temperature, ºC 200 ºC 400 ºC
A.6.1.7. SAFETY INTEGRITY LEVEL
A.6.1.7.1. The concept of Safety Integrity Level (SIL) shall be applied for valves dedicates to a HIPPS system.
A.6.1.7.2. The SIL is a representation of the required safety unavailability (average probability of failure on demand -
PFD) of a safety instrumented function (SIF).
A.6.1.7.3. The SIL classification shall be as listed in Table A.14, where SIL 4 has the highest level of safety integrity,
and SIL 1 has the lowest.
Table A.14 – SIL levels
SIL PFD Availability Risk Reduction Factor

SIL 1 0,1 to 0,01 0,90 to 0,99 10 to 100
SIL 2 0,01 to 0,001 0,99 to 0,999 100 to 1000
SIL 3 0,001 to 0,0001 0,999 to 0,9999 1000 to 10.000
SIL 4 0,0001 to 0,00001 0,9999 to 0,99999 10.000 to 100.000
A.6.1.7.4. Whenever requested in the VDS, such as for HIPPS valve, the SIL to be considered in the design of the valve
shall be SIL-3. The manufacturer shall present all documentation in order to certify that SIL 3 requirements were
achieved for the valve design.
A.6.1.8. BOLTING
A.6.1.8.1. The Studs, bolts and nuts used in the body-closure and body-bonnet shall be according:
Table A.15 - studs, bolts and nuts material specification
Body Material Studs / Bolts Material Nuts Coating
ASTM A105
ASTM A193 Gr. B7 ASTM A194 Gr. 2H
ASTM A216 Gr. WCB According
to item
ASTM A350 Gr. LF2 CL1 A.6.1.8.2
ASTM A320 Gr. L7 ASTM A194 Gr. 4L or 7L
ASTM A352 Gr. LCC
ASTM A350 Gr. LF3 CL1 ASTM A193 Gr. B8M or

ASTM A194 Gr. 8M N/A
ASTM A352 Gr. LC3 ASTM A193 Gr. B8M CL2
ASTM A182 Gr. F11 CL2

According
ASTM A217 Gr. WC6
ASTM A193 Gr. B16 ASTM A194 Gr. 7 to item
ASTM A182 Gr. F5
A.6.1.8.2
ASTM A217 Gr. C5
- Rev. 13 - Page 20 of 84
DISCIPLINE: PIPING
Body Material Studs / Bolts Material Nuts Coating
ASTM A182 Gr. F316
ASTM A351 Gr. CF8M
ASTM A182 Gr. F317 ASTM A193 Gr. B8M or

ASTM A194 Gr. 8M N/A
ASTM A351 Gr. CG8M ASTM A193 Gr. B8M CL2
ASTM A182 Gr. F347
ASTM A351 Gr. CF8C
A.6.1.8.2. Zn-Ni coating shall be applied to studs, bolts and nuts in lines with temperature up to 260°C. The studs, bolts
and nuts shall be coated with zinc-nickel (Zn-Ni) according to ASTM B841, Class 1, Type B / E, Grade 5-8, with post-
coating hydrogen embrittlement relief, according to ASTM B 849 and ASTM B 850; the maximum hardness for studs
and bolts shall be according to standard material specification.
A.6.1.8.3. For studs and bolts according to ASTM A320 Gr L7, and the valve body material is ASTM A350 Gr LF2 CL
1 or ASTM A352 Gr LCC, it will be acceptable charpy impact testing at -45°C. If the valve body material is ASTM A350
Gr LF3 or ASTM A352 Gr LC3, it will be acceptable charpy impact testing at -60°C;
A.6.1.8.4. The studs used in the body-closure (ball, check and plug) and body-bonnet (gate and globe) shall be
according to ASME B1.1, UNC-2A up to 25,40mm (1") and 8UN-2A, from 28,57mm (1 1/8") up, with standard hex nuts
according to ASME B18.2.2, with a minimum of four. The length of the studs shall have minimum of one and maximum
of three screw threads beyond the nut. For valves with DN 40 (1 1/2”) and smaller, is allowed the use of bolts according
to ASME B18.2.1. Alternatively, studs, bolts and nuts may be according metric units;
A.6.1.8.5. Valves subjected to fire type-testing shall be assembled with studs, bolts and nuts according Table A.15. For
the cases not covered in Table A.15, the manufacturer shall properly specify bolting materials. In this case, this set shall
be used for fire type-testing. As an alternative of ASTM A193 Gr B7, studs made of ASTM A193 Gr B16 may be used,
considering coating requirements indicated in item A.6.1.8.2.
A.6.1.8.6. Studs, bolts and nuts made of austenitic stainless steel (e.g.: Type 316) shall not be used when exposed to
wet marine atmosphere with maximum operating temperature above 60°C if. As an alternative, ASTM A193 Gr. B7 may
be used.
A.6.1.9. PAINTING
A.6.1.9.1. If painting of the valve is contractual required, the manufacturer shall present for PETROBRAS approval the
Painting Inspection Plan, according PETROBRAS’s specification and approved by a Painting Inspector Level II;
A.6.1.9.2. It shall be documented all painting inspection registers, and submitted for PETROBRAS;
A.6.1.9.3. The color to be applied on the valves shall according to DR-ENGP-M-I-1.15.
A.6.1.9.4. Coating systems specified for offshore and coastal applications shall be selected in accordance with ISO
12944-9 corrosion category CX high durability and I-ET 3010.00-1200-956-P4X-002.
A.6.1.10. MARKING AND NAMEPLATE
A.6.1.10.1. All valves shall be marked in accordance with the requirements stated on the design Standard referenced in
the VDS.
- Rev. 13 - Page 21 of 84
DISCIPLINE: PIPING
A.6.1.10.2. Each valve shall be provided with an austenitic stainless-steel nameplate securely affixed and so located
that it is easily accessible. Rivet holes shall be drilled prior to hydrostatic shell test.
A.6.1.10.3. The nameplate shall present information in accordance with the requirements stated on the design Standard
referenced in the respectively VDS, plus the additional data:
Indication about the VSL of the valve, such as: VSL-1, VSL-2, VSL3 or VSL-4.
Indication about fire tested design (when applicable).
Indication about fugitive emissions design (when applicable).
A.6.1.10.4. For trunnion mounted ball valves, despite of the separate identification plate requested by API 6D to indicate
the direction of seats valves with one unidirectional seat and one bidirectional seat, each valve shall present a separate
identification plate indicating the seat configuration, such as illustrated in Figure A.2.
For SPE / DPE seats For SPE / SPE seats

Figure A.2 – Example of nameplates with indication of seat configuration
A.6.1.10.5. Valves designed with unidirectional flow capability, i.e., flow occurs only in one direction, shall be marked
with a flow direction arrow or with a separate identification plate fixed to the body, indicating the direction for which flow
is permitted.
A.6.2. ACTUATOR
A.6.2.1. GENERAL
A.6.2.1.1. In general, all VDS contain technical specification considering manual actuated valves. The actuation for
manual valves may be as a wrench, hand wheel or gearbox operator.
A.6.2.1.2. Other types of actuators, such as hydraulic, pneumatic or electric, may be considered by PETROBRAS to
be used. In this case, the manufacturer shall design the valve and actuator considering also the specific datasheet.
A.6.2.1.3. When applicable (i.e.: control valve, SDV and BDV), the design of actuators shall consider the requirements
stated in DR-ENGP-M-I-1.5.
A.6.2.1.4. When applicable, the actuator shall be equipped with a positioning indicator, in order to show correct and
clearly the position of the valve (open or close). The position of a wrench or indicator shall be in the direction of the
line/bore when the valve is open and be perpendicular to the line/bore when the valve is closed.
A.6.2.1.5. For gearbox operator, the connection between the valve body and the gearbox shall be vented so that any
leakage from the stem cannot penetrate into the gearbox housing.
A.6.2.1.6. In case hydraulic actuator is considered, the manufacturer shall design it in order to have a maximum
operating pressure (e.g.: opening under full differential pressure) of 90% of the nominal operating pressure.
A.6.2.1.7. The actuator shall be designed with a safety factor of 2 times the nominal torque during normal operation
- Rev. 13 - Page 22 of 84
DISCIPLINE: PIPING
condition (maximum available torque = 2 x nominal torque).

A.6.2.1.8. For hand wheel actuated valves, the hand wheel shall be designed to allow operation of the valve under full
differential pressure. It shall also attend the requirements listed in MSS SP-91.
A.6.2.1.9. Levers and handwheels shall be in grade 316 stainless steel material.
A.6.2.2. ACTUATOR TYPE
A.6.2.2.1. Unless otherwise specified, the actuator type shall be according:
Table A.16 – Actuators type
Use of Gearbox
Pressure
Type x
Class
DN(NPS) ≥
150 300 (12)
300 250 (1 O)
Gate 600 150 (6)
900 100 (4)
1500, 2500 80 (3)
150, 300 200 (8)
Globe 600, 900 100 (4)
1500, 2500 80 (3)
150, 300 150 (6)
Ball 600, 900 100 (4)
1500, 2500 50 (2)
Butterfly Category A
CWP and 150 250 (1 O)
(concentric)
150 and 300 200 (8)

Butterfly Category B
(bi-eccentric / triple-eccentric)
600 160 (6)
150, 300 150 (6)

Plug
600, 900 100 (4)
A.7. SPECIFIC DESIGN REQUIREMENTS

A.7.1. BALL VALVE
A.7.1.1. DESIGN REQUIREMENTS
A.7.1.1.1. The valve shall be designed to operate and seal, according to design premises, under the following
conditions:
a) high pressure, equivalent to MWP, being able to operate and seal with high and low differential pressure.
- Rev. 13 - Page 23 of 84
DISCIPLINE: PIPING
b) low pressure, equivalent to LP of specific QSL requirement, being able to operate and seal with a low differential
pressure.
A.7.1.1.2. The type of the seats, regarding SPE or DPE, shall be used in the assembly of the valve in order to guarantee
the isolation valve configuration specified in the VDS (i.e.: DBB, DIB-1 or DIB-2). Any deviation shall be submitted for
PETROBRAS approval.
A.7.1.1.3. All sealings specified for the body construction shall be bi-directional, and no visible leakage shall be
considered to external environment.
A.7.1.1.4. The sealing type of the valve, regarding metal-to-metal or soft sealing, shall be according to the indication in
the VDS. Any deviation shall be submitted for PETROBRAS approval.
A.7.1.1.5. A metal-to-metal seated ball valve consists exclusively in use of a metal-to-metal sealing between seats and
ball, without the use of a non-metallic insert.
A.7.1.1.6. A soft seated ball valve consists in use of a non-metallic insert to guarantee its sealing performance. In this
case, the seat insert design and its groove shall be designed in order to prevent extrusion under all operation conditions.
A.7.1.1.7. Whenever specified in the VDS, the manufacturer shall attend to the metallic coating specified for the sealing
surfaces, such as in the body, bonnet, ball, seats, etc. In this case, the manufacturer shall attend the applicable
requirements listed on items A.7.1.7.3 and A.8.
A.7.1.1.8. Whenever specified in the VDS, the manufacturer shall attend to the hard coating specified for the sealing
surfaces, such as in the ball and seats. In this case, the manufacturer shall attend the applicable requirements listed on
items A.7.1.7.4 and A.8.2.2.
A.7.1.1.9. Whenever specified in the VDS, the manufacturer shall attend to the organic coating specified. In this case,
the manufacturer shall attend the applicable requirements listed on item A.8.2.2.4.
A.7.1.1.10. Trunnion valves with NPS 3 (DN 80) and smaller may have a single drain and vent connection, at the lowest
possible position on the valve body cavity. Valves NPS 4 and higher shall contain both drain and vent ports, in order to
allow drain, purge, pressurization and monitoring through the body during testing. MSS SP45 shall be considered, with
the additional requirements:
Figure A.3 - Location of drain and vent ports
a) For trunnion ball valves, the body shall contain a threaded hole with drain plug in position "G" or "J", according
Figure A.3. It is not allowed to mount plugs using PTFE tape.
- Rev. 13 - Page 24 of 84
DISCIPLINE: PIPING
b) The plug shall be specified considering the alert given in A.6.1.1.10.
A.7.1.1.11. For trunnion ball valves type DIB-1, or when requested in the VDS, it shall be provided with an automatic
cavity-pressure relief. In this case, it shall be considered the use of a block valve before the cavity-relief valve.
A.7.1.1.12. For floating ball valves (NPS ≥ 2) and for trunnion ball valves, it shall be designed in order to allow pressure
relief in the cavity from exceeding 1,33 times the valve pressure rating at the specified maximum operating temperature.
A.7.1.1.13. The ball shall be full bore type, cylindrical and solid as shown in Figure A.4.
Figure A.4 – Ball type
A.7.1.2. DESIGN STANDARD
A.7.1.2.1. The following standards shall apply to the design of ball valves:
- Rev. 13 - Page 25 of 84
DISCIPLINE: PIPING
Table A.17 – Design Standards for ball valves
Body / Closure Material
Casting or Forging Forging

Description
Butt
Flanged b Socket weld c Flanged
weld c
DN a 50 up to 900 50 up to 600 50 up to 400 50 up to 300 15 up to 40

(NPS) (2 up to 36) (2 up to 24) (2 up to 16) (2 up to 12) (1/2 up to 1 1/2)
150, 300 150, 300, 600

Class 900 1500 2500 800 1500 2500
600 900, 1500, 2500
ASME
Standard API 6D / IOGP S-562 d ISO 17292 API 6D
B 16.34 LTD
a DN = Nominal diameter, in millimeters (mm).
b For DN > standard diameter, face to face shall be by agreement between manufacturer and PETROBRAS. The design shall be
according to ASME B16.34.

c The design of the valve shall consider the use of a nipple with extension of 100,00 millimeters.
d As applicable. See also A.7.1.8.
A.7.1.3. MOUTING TYPE
A.7.1.3.1. The design of metallic ball valves (metal-to-metal or soft seated) shall attend the following characteristic
regarding mounting:
Table A.18 – Mounting type for ball valves
DN (NPS) 150 300 600 800 900 1500 I 2500

I I I
15 (1/2) up t o 40 (1 1/2) Floating
Trunnion
50 (2) up to 100 (4) Floating a, b Trunnion c
150 (6) and above Trunnion

a Single ball valves used for LIT / LG block shall be trunnion-mounted, DIB-2 configuration.
b Double ball valves NPS 3 and 4, classes 150 and 300, shall be trunnion-mounted.
c Double ball valves NPS 2, classes 600 and 900, shall be floating.
A.7.1.4. ISOLATION VALVE CONFIGURATION
A.7.1.4.1. SINGLE PISTON EFFECT (SPE) OR SELF-RELIEF (SR) SEAT:
A SPE/SR assembly seat provides sealing only when differential pressure is higher from outside of the
valve. When the SPE assembly seat faces higher differential pressure from inside of the valve (cavity), it occurs self-
relieving.
A SPE/SR assembly seat may be provided on a metal-to-metal seat design or on a soft seated design.
- Rev. 13 - Page 26 of 84
DISCIPLINE: PIPING
Left side of Figure A.5 illustrates the sealing mechanism when pressure (or higher differential pressure)
is applied from outside of the valve. The difference in the area (“D”) times the line pressure creates a piston effect force
which pushes the seat against the ball surface resulting in a sealing between ball and seat.
Right side of Figure A.5 illustrates the relief mechanism when a higher differential pressure is applied
from the cavity of the valve. When the pressure in the valve cavity reaches certain pressure (so that the total force from
cavity pressure that act on the seat is higher than the force causing by the upstream pressure), the trapped pressure
will have enough force to push the seat and relief the valve cavity pressure.
Figure A.5 – SPE/SR seat assembly mechanism (illustration on a soft ball valve)
A.7.1.4.2. DOUBLE PISTON EFFECT (DPE) SEAT:
A DPE assembly seat provides sealing on both directions, when differential pressure is higher from
outside/inside of the valve.
A DPE assembly seat may be provided on a metal-to-metal seat design or on a soft seated design.
Left side of Figure A.6 illustrates the sealing mechanism when pressure (or higher differential pressure)
is applied from outside of the valve. The difference in the area (“D”) times the line pressure creates a piston effect force
which pushes the seat against the ball surface resulting in a sealing between ball and seat.
Right side of Figure A.6 illustrates the sealing mechanism when pressure (or differential pressure) is
applied from the cavity of the valve. The difference in the area (“D”) times the cavity pressure creates a piston effect
force which pushes the seat against the ball surface resulting in a sealing between ball and seat.
Figure A.6 – DPE seat assembly mechanism (illustration on a soft ball valve)
A.7.1.4.3. Whenever not specified in the VDS, the valve design shall consider as a standard isolation valve configuration
the use of two unidirectional sealing seats, giving a characteristic of single piston effect (SPE) or self-relief (SR) on both
seats.
A.7.1.4.4. In order to ensure adequate operational requirements, whenever specified in the VDS, the design of trunnion
- Rev. 13 - Page 27 of 84
DISCIPLINE: PIPING
ball valves (metal-to-metal or soft seated) may fulfill one or more of the following functions/features:
a) DOUBLE BLOCK AND BLEED (DBB):
The DBB feature of the valve is the ability to segregate two pressure sources and to bleed/vent pressure in the valve
body between the two seats when the valve has the DBB feature. The DBB feature may be obtained by using SPE/SR
or DPE seats.
Figure A.7 – DBB feature (ref.: Double Block and Bleed - Type B of API 6D)
b) DOUBLE ISOLATION AND BLEED 1 (DIB-1):
The DIB-1 feature of the valve is the ability to provide two sealing elements to a single pressure source, and to bleed/vent
between the two sealing elements. It shall be considered Upstream and Downstream as bidirectional sealing seat (DPE
seats).
Figure A.8 – DIB-1 feature (ref.: Double Isolation and Bleed - Type B of API 6D)
Valves designed with a DIB-1 feature shall be provided with automatic cavity-pressure relief, unless otherwise agreed.
In this case, it shall be attended all requirements described on API 6D (ref. item 5.5 of API6D).
c) DOUBLE ISOLATION AND BLEED 2 (DIB-2):
The DIB-2 feature of the valve is the ability to provide two sealing elements to a single pressure source, and to bleed/vent
between the two sealing elements. It shall be considered the Upstream as unidirectional sealing seat (SPE seat) and
downstream as bidirectional sealing seat (DPE seat).
Figure A.9 – DIB-2 feature (ref.: Double Isolation and Bleed - Type B of API 6D)
- Rev. 13 - Page 28 of 84
DISCIPLINE: PIPING
All DIB-2 valves shall have a clear identification about seat sealing direction, by marking on a separate identification
plate affixed to valve body both seats type of sealing (SPE or DPE).
The assembly of a DIB-2 valve on the line shall attend its preferred direction.
A.7.1.4.5. Depending on detailed design, indicated in the VDS, the valve may have an isolation valve configuration as
follows:
Table A.19 – Isolation Valve Configuration for Ball Valves
Isolation valve Single Piston Double Block and Bleed Double Isolation and Bleed
Effect (SPE) on
configuration both seats (DBB) Feature (DIB-2) Feature
1 Yes No No
2 Yes Yes No
1
3 No Yes Yes
4 No Yes 2 Yes
1
DBB feature applied in the closed position (only).
2
DBB feature applied in the opened and closed position (both).
Note: The use of DIB-1 feature has not been foreseen. Particular analyses of use may be conducted by Project
team and/or an Operational Unit (UO).
A.7.1.5. NON-METALLIC SEALS
A.7.1.5.1. All non-metallic seals shall be suitable for the pressure, temperature and service conditions considered in
this item.
A.7.1.5.2. The manufacturer of the valve shall guarantee together with your seals supplier(s) the attendance of the
essential material requirements for the non-metallic seals, in order to ensure that the designed seal system works
properly during the whole design life of the valve.
A.7.1.5.3. The VDS of soft seated ball valves indicates the material of the seat insert.
A.7.1.5.4. The use of certain seat insert material shall be based on the following classification:
Table A.20 – Non-metallic materials for seat insert seal design
Design Temp. (ºC)

Material Pressure Class
Minimum Maximum
PTFE reinforced with 25% of Carbon 150, 300 -46 +150
Devlon V-API 1 600, 900 -46 +120
PEEK Based 2 600, 900, 1500, 2500 - 46 +150

1 The use of Devlon V-API is not allowed on valves applied on AM (amine) systems.
2 The use of PEEK is acceptable for pressure class 2500 only up to 120ºC.
Note: The values listed in Table A.20 presents the limits of temperature that shall be applied in the valve design
considering operational conditions of it.
A.7.1.5.5. For the design of the seats / stem seals, in metal-to-metal or soft seated ball valves, the VDS contains
- Rev. 13 - Page 29 of 84
DISCIPLINE: PIPING
indication about the non-metallic group material that shall be considered in the valve design.
A.7.1.5.6. The materials of each group are indicated in Table A.21, according to the following classification:
- Group A – Terpolymer of VF2, HFP e TFE with fluor content of ~ 67 - 70% or HNBR with %ACN between 36
and 40%. E.g.: Viton B (DuPont), Technoflon TN (Solvay Solexis);
- Group B – Ter- or Tetrapolymer of TFE, VF2 and PMVE with fluor content of ~ 62-68% or HNBR LT (%ACN
between 36 and 40%) both with TR10 ≤ -30°C according to ASTM D1329. E.g.: Viton GLT (DuPont), Technoflon
855 (Solvay Solexis);
- Group C – Terpolymer of PP, TFE and VDF with higher resistance to bases or perfluoro elastomer (FFKM). e.g.:
FKM Type 4- Aflas (Asashi Glass), BRE 7132 (Dyneon), FFKM- Kalrez, Chemraz, Technoflon PFR (Solvay
Solexis);
- Group D – Terpolymer of PP, TFE and VDF with higher resistance to aromatic hydrocarbons or perfluoro
elastomer (FFKM). e.g.: BRE 7132 (Dyneon), FFKM- Kalrez, Chemraz, Technoflon PFR (Solvay Solexis);
- Group E – Polytetrafluoroethylene (PTFE) based Chevron Packing or Polytetrafluoroethylene (PTFE) energized
with a Co-Cr-Ni alloy UNS R30003 (Elgiloy) spring;
- Group F – Graphite 98% pure, Graphoil or a metallic seal.
Table A.21 – Seal groups materials
Design Transient
Seals Temp. 1 Temp. 2 Seals Seals Group
Application RGD Suitable for
Group Min. Max. Min. Max. Materials Design Restrictions
(° C) (° C) (° C) (° C)
O-ring Water, Utility, Amines
HNBR Steam
Normal Polypak Sweet
Group A 0 +150 0 +170 No Aromatic
Temperature FKM Type 2 hydrocarbon
Gasket and Chemicals hydrocarbons 4
O-ring
HNBR LT Sweet Amines, Steam,
Low Polypak
Group B
Temperature
- 30 +150 - 46 +170
FKM Type 3 Yes 3 hydrocarbon Aromatic
Gasket (Gas) hydrocarbons 4
FKM Type 4 O-ring Amines, Amine

based Aromatic
Medium High FKM Type 5 Polypak
Group C
Temperature
0 +210 0 +240 No scavengers and hydrocarbons 4,
Gasket Inhibitors, Xylene
FFKM
Steam
O-ring
Medium High FKM Type 5
Group D Temperature + 0 +210 0 +240 Polypak No All -
Aromatics FFKM
Gasket
PTFE based
Wide Range Chevron Seal6
Group E 5
- 100 +200 - 100 +240 PTFE based + N/A All -
Service UNS R30003 Lip Seal
(Elgiloy)
Graphite 98% Pure
Gasket
High Graphoil
Group F - 100 +500 - 100 +500 N/A All -
Temperature C-Ring
Metallic Seal
1 Temperature range for use of non-metallic material (i.e.: seats / stem seals) in the valve design. It shall be considered for
continuous service without reducing the seals' economic life or its sealing capability.
- Rev. 13 - Page 30 of 84
DISCIPLINE: PIPING
2 Temperature range considered whether the seals may be exposed for a short period of time (transient temperature spike),
under a static condition (without operation), with a possible leakage but without permanently damaging the sealing system.
3 RGD according to ISO 23936-2 for valves of pressure class 300 or above.
4 Hydrocarbons streams containing more than 25% aromatics.
5 The use of Group E is acceptable in replacement of Groups A, B, C or D, as long as the design of the valve considers application
of Alloy 625 overlay (partial clad) on all sealing areas.
6 Use of Chevron packing shall be combined with anti-extrusion PEEK rings.
A.7.1.5.7. As a reference, the use of each group seal is based to the following fluid classes & temperature ranges:
Table A.22 – Indication of groups of seals according to fluid class and temperature range
Temperature Range
Fluid Class Normal Low Medium High Wide Range High
(0 ° C to +1 5 0 ° C ) ( - 3 0 ° C to +1 5 0 ° C ) (0 ° C to +2 1 0 ° C ) ( - 1 0 0 ° C to +2 0 0 ° C) ( - 1 0 0 ° C to +5 0 0 ° C)
Utility Group A - - - -
Water Group A - - - -
Hot Water - - Group C - -
Steam Group C - Group C - -
Sweet Hydrocarbon 1 Group A Group B Group C - -
Sour Hydrocarbon 2 Group C Group E Group C Group E Group F
Aromatic Hydrocarbon 3 Group D Group E Group D Group E Group F
Chemicals 4 Group A - Group C - -
High CO2 content 5 - - - Group E -
Amine (MEA) 6 Group C - Group C - -

1 Hydrocarbon streams containing less than 1% H2S (10.000 ppm).
2 Hydrocarbon streams containing more than 1% H2S (10.000 ppm). Qualification and production testing of elastomers and thermoplastics
shall be performed in accordance with NORSOK M-710 or ISO 23936 Parts 1 and 2, qualifying the materials for sour service for the
temperature range specified valve datasheet.
4 It shall be considered the use of Group A for all chemicals typically used in a production facility (e.g.: inhibitors, scavengers, etc.), and
Group D for amine-based chemicals or xylene.
5 Hydrocarbon streams containing CO2 with more than 10 mol%.
6 Monoethanolamine.
A.7.1.5.8. For the indication of a valve configuration, it shall be considered the following classification as a part of the
valve code, according to description of valve code presented on item A.11.5:
- Rev. 13 - Page 31 of 84
DISCIPLINE: PIPING
Table A.23 – Seals group classification into valve code
Seals Group Soft Metal x Metal

A or B 1 5
C 2 6
D or E 3 7
F N/A 8
Fugitive Emissions 4 9
A.7.1.5.9. The housing design of elastomeric O-rings shall prevent risk of extrusion by use of thermoplastic back-up
rings on both sides (PEEK or reinforced PTFE) for valves in piping class 900 and above.
A.7.1.6. TYPICAL CONFIGURATIONS
A.7.1.6.1. This item presents typical configurations for ball valves, as a result of combinations of materials and features.
The configurations herein listed are considered to create a specific VDS.
A.7.1.6.2. The referred number of the typical configuration of the valve, shown on the first column of Table A.25 and
Table A.26, shall be considered as a part of the valve code, according item A.11.5.
A.7.1.6.3. BALL VALVES UP TO NPS 1 1/2 (“FORGED” VALVES)
The design of ball valves up to NPS 1 1/2 (“Forged” valves) shall consider the use of a nipple with
extension of 100,00 millimeters.
For the indication of the nipple considered in the valve configuration, it shall be considered the following
classification as a part of the valve code, according to description of valve code presented on item A.11.5.
Table A.24 – Nipple classification into valve code
Pressure Class
SCH
800 1 1500 2500
40S 801 1501 2501
80 802 1502 2502
160 803 1503 2503
XXS 804 1504 2504
1 Code 800 is used for screwed ended connections.
The following basic configurations shall be considered in the design of ball valves up to NPS 1 1/2
(“Forged” valves):
- Rev. 13 - Page 32 of 84
DISCIPLINE: PIPING
Table A.25 – Typical configurations for ball metallic valves up to NPS 1 1/2 (“Forged” Valves)
Pressur
Config. Sealing Seat Insert Stem Seal Fire End Seats Fugitive
e DBB VSL
# Type Material Material Tested Connection Configuration Emission
Class
150, 300 PTFE + 25%C
N/A
600, 900
00 Soft Group B Yes Flanged No 1, 2
1500, PEEK
SPE x SPE
2500
01 PTFE + 25%C Group B
02 PTFE + 25%C Group C, E

Soft
03 800 PEEK Group B Yes SW, SE N/A No 1, 2, 3
04 PEEK Group C, E
No
Metal to
05 Metal
N/A Group D, E
06 Soft PEEK Group B

1500 Yes SW SPE x SPE No 1, 2, 3
Metal to
07 Metal
N/A Group D, E
08 Soft PEEK Group B

2500 Yes BW SPE x SPE No 1, 2, 3
Metal to
09 Metal
N/A Group D, E
Metal to
0A Metal
800 N/A Group F Yes SW N/A No 1, 2, 3
- Rev. 13 - Page 33 of 84
DISCIPLINE: PIPING
Pressur
Config. Sealing Seat Insert Stem Seal Fire End Seats Fugitive
e DBB VSL
# Type Material Material Tested Connection Configuration Emission
Class
150, 300 PTFE + 25%C
N/A
600, 900
F0 Soft Group B Flanged No 1, 2
1500, PEEK
SPE x SPE
2500
F1 PTFE + 25%C Group B
F2 PTFE + 25%C Group C, E

Soft
F3 800 PEEK Group B SW, SE N/A No 1, 2, 3
F4 PEEK Group C, E
Metal to
F5 Metal
N/A Group D, E Yes Yes
F6 Soft PEEK Group B

1500 SW SPE x SPE No 1, 2, 3
Metal to
F7 Metal
N/A Group D, E
F8 Soft PEEK Group B

2500 BW SPE x SPE No 1, 2, 3
Metal to
F9 Metal
N/A Group D, E
Metal to
FA Metal
800 N/A Group F SW N/A No 1,2
FB Soft 1500 PEEK Group E SW SPE x SPE No 1, 2
A.7.1.6.4. BALL VALVES NPS 2 AND ABOVE AND DOUBLE BALL VALVES NPS 3 AND ABOVE
The following basic configurations shall be considered in the design of small ball and double ball valves:
- Rev. 13 - Page 34 of 84
DISCIPLINE: PIPING
Table A.26 – Typical configurations for metallic ball valves NPS 2 and above and double ball valve NPS 3 and above
Config. Sealing Fire Seats Fugitive

Seat Insert Pressure Class DBB VSL
# type Tested Configuration emission
0 No 1, 2
PTFE+25%C 150, 300 SPE x SPE No
1 Yes 2
2 No 1, 2
PEEK 600, 900 SPE x SPE No
3 Yes 2
4 No 600, 900 1, 2
Soft PEEK SPE x SPE Yes
5 Yes 1500, 2500 2
6 No
PTFE+25%C 150, 300 DIB-2 Yes 2, 3 2
7 Yes
8 No No
600, 900
PEEK DIB-2 Yes 2, 3 2
9 Yes 1500, 2500
0 No 150, 300, 600 1, 2

SPE x SPE No
1 Yes 900, 1500, 2500 2
2 Metal No 150, 300, 600
DIB-2 Yes 2, 3
3 to N/A Yes 900, 1500, 2500
Metal
150, 300, 600
4 Yes
900, 1500, 2500
DIB-2 Yes 1 4
53 Yes 1500, 2500 DIB-2 Yes 1 4

PTFE+25%C 150, 300 SPE x SPE No 2
F 600, 900
PEEK SPE x SPE Yes 2
1500, 2500
Soft
PTFE+25%C 150, 300 DIB-2 Yes 2, 3 2
G 600, 900
PEEK DIB-2 Yes 2, 3 2
1500, 2500
Yes 150, 300, 600 Yes
F 900, 1500, 2500
SPE x SPE No 2
Metal 150, 300, 600

G 900, 1500, 2500
DIB-2 Yes 2, 3
to N/A
Metal 150, 300, 600
U 900, 1500, 2500
DIB-2 Yes 1 4
E3 1500, 2500 DIB-2 Yes 1 4

1 DBB designed for fully opened and closed position. The valve shall be able to perform DBB test on both conditions.
2 Soft seated ball valves with VSL-3 shall not be considered for use in hydrocarbon service lines.
3 Valve configurations used for HIPPS application.
A.7.1.6.5. RISING STEM BALL VALVES
The following basic configuration shall be considered in the design of rising stem ball valves:
Table A.27 – Typical configurations for rising stem ball valves
Config. # Sealing type Seat Insert Fire Tested Pressure Class VSL
9 Metal to Metal N/A Yes 600,900 2,3
A.7.1.6.6. DOUBLE BALL VALVES
- Rev. 13 - Page 35 of 84
DISCIPLINE: PIPING
Table A.28 – Typical configurations for metallic double ball valves up to NPS 2
Config. Sealing Seat Stem Seal Fire End Fugitive

Pressure Class VSL
# type Seat Insert Material Tested Connection emission
PTFE+25%C 150, 300
01 Flanged
PEEK 600, 900, 1500, 2500
Group B
PTFE+25%C 150, 300 Flanged x
02 NPT
PEEK 600, 900, 1500, 2500
Soft
PTFE+25%C 150, 300
03 Flanged
PEEK 600, 900, 1500, 2500
Group E
04 NPT
PEEK 600, 900, 1500, 2500 Yes 2 No
05 Flanged
Group E
Flanged x
06 NPT
Metal
150, 300, 600
to N/A
900, 1500, 2500
Metal
07 Flanged
Group F
Flanged x
08 NPT
PTFE+25%C 150, 300

F1 Flanged
PEEK 600, 900, 1500, 2500
Group B
F2 NPT
PEEK 600, 900, 1500, 2500
Soft
PTFE+25%C 150, 300
F3 Flanged
PEEK 600, 900, 1500, 2500
Group E
F4 NPT
PEEK 600, 900, 1500, 2500 Yes 2 Yes
F5 Flanged
Group E
Flanged x
F6 NPT
Metal
150, 300, 600
to N/A
900, 1500, 2500
Metal
F7 Flanged
Group F
Flanged x
F8 NPT
A.7.1.7. MATERIALS CONFIGURATIONS
A.7.1.7.1. STEM MATERIALS
Table A.29 presents the standardized materials for each combination of material and pressure class of
- Rev. 13 - Page 36 of 84
DISCIPLINE: PIPING
the valve. The stem materials listed herein are considered to create a specific VDS.
Alternative materials are presented when applicable. The use of it shall be approved by PETROBRAS.
Table A.29 - Stem materials according to material class & pressure class of the valve
Pressure Class Alternative

Material Class
150 300 600 800 900 1500 2500 Materials
ASTM A564 Type
630 (UNS S17400)
ASTM A276 or
A479 (UNS
ASTM A276 or A479
Carbon Steel S31803)
(UNS S41000)
ASTM A276
(UNS S32760)
ASTM B637
(UNS N07718)
ASTM A564 Type

630 H1150 (UNS
S17400)
ASTM A276 or
Low ASTM A564 Type
A479 (UNS
Temperature ASTM A276 or A479 (UNS S31600) 630 H1150 (UNS
S31803)
Carbon Steel S17400)
ASTM A276
(UNS S32760)
ASTM B637
(UNS N07718)
ASTM A276 or
Carbon Steel A479 (UNS
S31803)
with Organic
ASTM A276 or A479 ASTM A276 or
Coating
(UNS S31803) A479
(Onshore / (UNS S32760)
Offshore) ASTM B637
(UNS N07718)
Carbon Steel
with Alloy 625 ASTM B637
N/A
overlay (UNS N07718)
(UNS N06625)
ASTM B637
ASTM A276 or A479
Stainless Steel ASTM A276 or A479 (UNS S31600) (UNS N07718) 1
(UNS S31803) 1
ASTM A182 FXM-19
ASTM A276
(UNS S32760)
ASTM A276 or A479 ASTM B637
Duplex Steel
(UNS S31803) (UNS N07718)
Hastelloy C276
(UNS N10276)
ASTM B637
Super Duplex ASTM A276 or A479 (UNS N07718)
Steel (UNS S32760) Hastelloy C276
(UNS N10276)
Alloy Steel
ASTM B637
(ASTM A333 N/A
(UNS N07718)
Gr.3)
Alloy Steel
ASTM B637
(ASTM A333 N/A
(UNS N07718)
Gr.8)
- Rev. 13 - Page 37 of 84
DISCIPLINE: PIPING
Pressure Class Alternative

Material Class
150 300 600 800 900 1500 2500 Materials
1
Whenever Group E is considered as seats / stem seals material in metal-to-metal ball valves (due to low temperature
requirements), it shall be used ASTM B637 (UNS N07718).
A.7.1.7.2. SPRING MATERIAL
All valves design shall consider the use of Alloy X750 (UNS N07750) as spring material, to be used on
the seat assembly.
A.7.1.7.3. METALLIC COATING
Whenever specified in the VDS use of partial clad, it shall be considered the application according:
Table A.30 – Specification of metallic coating (partial clad) for ball valves
Partial Clad
Stainless Steel
(AISI 316) Valves with VSL = 2 which Material Class is Carbon Steel or Low Temperature Carbon Steel
Weld Overlay
Nickel Alloy Valves with VSL ≥ 3 and all valves with seals (seats/stem) using Group E.
(Alloy 625) Note: Only applicable for valves with Material Classes Carbon Steel, Low Temperature Carbon Steel or
Weld Overlay Stainless Steel
Whenever specified in the VDS partial clad, it shall be considered the application of CRA (according
Table A.30) on all body sealing areas.
Whenever specified in the VDS full clad, it shall be considered the application of Nickel Alloy (Alloy 625)
Weld Overlay on all wetted parts.
All metallic coatings shall attend the specific requirements listed in item A.8.2.1.
A.7.1.7.4. HARD COATING
All designs of soft ball valves shall consider the application of hard coating on seats / ball according:
Table A.31 – Specification of hard coating on seats / ball on soft ball valves
Pressure Class
VSL
150 300 600 900 1500 2500 10000
VSL-1 N/A
Tungsten Carbide
VSL-2 N/A or
Chrome Carbide
Tungsten Carbide
VSL-3 N/A or
Chrome Carbide
VSL-4 N/A
All designs of metal-to-metal ball valves shall consider the use of hard coating on seats / ball according:
- Rev. 13 - Page 38 of 84
DISCIPLINE: PIPING
Table A.32 – Specification of hard coating on seats / ball on metal-to-metal ball valves
Pressure Class
VSL
150 300 600 900 1500 2500 10000
VSL-1 Chromium
Tungsten Carbide 2
or
Electroplate 1
VSL-2 Chrome Carbide
VSL-3
Tungsten Carbide 2, Chrome Carbide or Chrome-Nickel Spray and Fuse
VSL-4
1If requested by the manufacturer, it may be acceptable the use of tungsten carbide or chrome carbide
coating.
2 For valves which maximum design temperature 210ºC.
All hard coatings application shall attend the specific requirements listed in item A.8.2.2.
A.7.1.7.5. SOFT SEATED BALL VALVES
Table A.33 – Typical configurations for soft seated ball valves according to material class
Pressure Seat Insert Body Ball / Seats

Material Class
Class Material Material 2 Material 3
150
PTFE + 25%C AISI 410
300
600 ASTM A105 AISI 410

800 PEEK or +
Carbon Steel 900 ASTM A216 WCB
Hard Coating 3
+
Partial Clad 1 AISI 410
1500
PEEK +
2500
Hard Coating 3
150
300
ASTM A350 LF2 Cl1
600 AISI 316
Low or
Temperature 800 PEEK ASTM A352 Gr.LCC +
Carbon Steel 900 + Hard Coating 3
1500
PEEK +
2500
Hard Coating 3
Carbon Steel
ASTM A105
with 150
PTFE + 25%C or ASTM A995 Gr.1b
Organic Coating 300
ASTM A216 WCB
(Onshore)
150
Carbon Steel PTFE + 25%C UNS S31803
300 ASTM A105
with
or UNS S31803
Organic Coating
ASTM A216 WCB
(Offshore) 1500 PEEK +
Hard Coating 3
- Rev. 13 - Page 39 of 84
DISCIPLINE: PIPING
150
300
ASTM A182 Gr. F316 AISI 316
600
or
800 PEEK +
Stainless Steel ASTM A351 Gr. CF8M
900 Hard Coating 3
+
1500
PEEK +
2500
Hard Coating 3
150
PTFE + 25%C UNS S31803
300
ASTM A182 Gr. F51
600 or UNS S31803
800 PEEK ASTM A995 Gr. 4a +
Duplex Steel
900 or Hard Coating 3
ASTM A995 Gr. 1b
(onshore only) UNS S31803
1500
PEEK +
2500
Hard Coating 3
150
PTFE + 25%C UNS S32760
300
600 UNS S32760

800 PEEK ASTM A182 Gr. F55 +
Super Duplex
or
Steel 900 Hard Coating 3
ASTM A995 Gr 6a
UNS S32760
1500
PEEK +
2500
Hard Coating 3
Alloy Steel 600 ASTM A350 Gr. LF3 UNS N06625

(ASTM A333 800 PEEK or +
Gr.3) 900 ASTM A352 Gr. LF3 Hard Coating 3
Alloy Steel ASTM A522 Type I

(ASTM A333 2500 PEEK ASTM A522 Type I +
Gr.8) Hard Coating 3
1 Partial clad may be requested in the VDS and shall be according Table A.30.
2 The use of forging or casting shall be according VSL classification. For valves with NPS < 2, It shall be
considered only the use of forging material.
3 Hard Coatings may be requested in the VDS and shall be applied according Table A.31.
A.7.1.7.6. METAL SEATED BALL VALVES
Table A.34 – Typical configurations for metal-to-metal seated ball valves according to material class
- Rev. 13 - Page 40 of 84
DISCIPLINE: PIPING
Material Class Pressure Class Body Material 1, 2 Ball / Seats Material 3
ASTM A105
or AISI 410
Carbon Steel ASTM A216 WCB +
+ Hard Coating 3
Partial Clad 1
ASTM A350 LF2 Cl1

Low or AISI 316
Temperature ASTM A352 Gr.LCC +
150
Carbon Steel + Hard Coating 3
300 Partial Clad 1
600
800
900 ASTM A182 Gr. F316L
or AISI 316
Stainless Steel 1500 ASTM A351 Gr. CF8M +
2500 + Hard Coating 3
10000psi Partial Clad 1
ASTM A182 Gr. F51 UNS S31803

Duplex Steel or +
ASTM A995 Gr 4A Hard Coating 3
ASTM A182 Gr. F55 UNS S32760

Super Duplex
or +
Steel
ASTM A995 Gr 6A Hard Coating 3
Alloy Steel 600 ASTM A350 Gr. LF3 UNS N06625

(ASTM A333 800 or +
Gr.3) 900 ASTM A352 Gr. LF3 Hard Coating 3
Alloy Steel ASTM A522 Type I

2500
(ASTM A333 ASTM A522 Type I +
Gr.8) 10000psi Hard Coating 3
1 Partial clad may be requested in the VDS and shall be according Table A.30.
2 The use of forging or casting shall be according VSL classification. For valves with NPS <
2, It shall be considered only the use of forging material.
3 Hard Coatings may be requested in the VDS and shall be applied according Table A.31.
A.7.1.8. BALL VALVES ACCORDING TO IOGP S-562
A.7.1.8.1. Ball valves included in scope of S-562 shall comply with S-562, this Annex and following
requirements/modifications.
A.7.1.8.2. Design validation shall be as required by Table A.3.
A.7.1.8.3. Process fabrication for body materials shall be according Table A.7.
A.7.1.8.4. Table J.3 of S-562, sequence 7, shall be read as: Low-pressure pneumatic seat test at 5 psi to 14.5 psi (0.34
bar to 1 bar) per H.3.2 Type I.
- Rev. 13 - Page 41 of 84
DISCIPLINE: PIPING
A.7.1.8.5. For fluid services such as aromatic hydrocarbons, steam, methanol, amines, strong alkalis and some Freons,
Table A.21 and Table A.22 shall be used as reference to selection of suitable sealing material.
A.7.1.8.6. For classes 150 to 600, all sizes, and for classes 900 to 2500, sizes NPS 8 (DN 200), vents and drains shall
have double seal (axial outboard and radial inboard) parallel threads with locking ring. During loosening of the fitting, the
design configuration shall ensure pressure is relieved from the inboard seal without thread disengagement.
A.7.1.8.7. NDE, tests and documentation of each valve shall be according A.7.1.8.7.1 to A.7.1.8.7.4.
VSL-1 valves shall comply with S-562 QSL-1 requirements.

VSL-2 valves shall comply with S-562 QSL-2 or QSL-2G requirements as applicable.
VSL-3 valves shall comply with S-562 QSL-3 or QSL-3G requirements as applicable.
VSL-4 valves shall comply with S-562 QSL-4 requirements.
A.7.1.8.8. SDV, BDV, XV and ADV valves shall be fire tested. For other valves, fire type-tested certified design shall be
required according to design premises.
A.7.2. GATE VALVE

A.7.2.1.1. It shall be considered a Metal-to-Metal seated design for all types of gate valve. Expanding gate valves may
have an additional non-metallic insert.
A.7.2.1.2. Whenever specified in the VDS, the manufacturer shall attend to the requirement of coating, such as metallic
coating, hard coating and/or organic coating specified for some parts and sealing surfaces, such as in the body, bonnet,
gate, seats, etc. In this case, the manufacturer shall attend the applicable requirements listed on item A.8.2.
A.7.2.1.3. Gate valves, with flanged or butt weld ends, shall have face to face dimensions according to ASME B16.10.
A.7.2.1.4. End connections shall be according:
a) Flanged ends: according to ASME B16.5 up to DN 600 (NPS 24) for ASME classes 150 to 1500, and up to DN
300 (NPS 12) for class 2500; according to ISO 27509 for DN 400 (NPS 14) to NPS 600 (NPS 24) in ASME class
2500; according to ASME B16.47 Series A from DN 650 (NPS 26) up to DN 1500 (NPS 60) for ASME Classes
150 to 600, and from DN 650 (NPS 26) up to DN 1200 (NPS 48) for ASME class 900.
b) Screwed ends: according to ASME B1.20.1 NPT;
c) Butt weld: according to ASME B16.25;
d) Socket weld: according to ASME B16.11.
A.7.2.1.5. The design of gate and body guides shall be optimized with respect to chamfers, clearances and machining
to ensure valves operate smoothly during operation without self-locking, seizure, internal wear or galling effects in the
absence of any form of lubrication.
A.7.2.1.6. In case the design of a gate valve consider the use of drain and vent ports, the plugs shall be specified
considering the alert given in item A.6.1.1.10.
A.7.2.1.7. Up to and including DN 40 (NPS 1 ½), the valve shall be furnished with a solid wedge.
A.7.2.2.1. The following standards shall be considered for the design of gate valves:
- Rev. 13 - Page 42 of 84
DISCIPLINE: PIPING
Table A.35 – Design Standards for gate valves

Description Forging Forging or Casting
Socket weld Butt weld Flange Flange
DN 15 up to 40 25 up to 40 46 up to 346 50 up to 600 50 up to 400 50 up to 300

(NPS) (1/2 up to 1 1/2) (1 up to 1 1/2) (1 13/16 up to 13 5/8) (2 up to 42) (2 up to 24) (2 up to 12)
Class 800 and 1500 2500 10.000 psi 150 and 300 600 to 1500 2 500
ASME
Standard API 602
B16.34 LTD
API 6A API 600 or API 603 / IOGP S-611 a
a As applicable. See also A.7.2.5
A.7.2.3.1. All non-metallic seals shall be suitable for the pressure, temperature and service conditions specified in the
VDS.
A.7.2.3.2. The manufacturer of the valve shall guarantee together with your seals supplier(s) the necessary material
requirements for the non-metallic seals, in order to ensure that the designed seal system works properly during the
whole design life of the valve.
A.7.2.3.3. For solid wedge gate valves, the design shall consider the use of gaskets made of flexible graphite with
inconel wire for the stem seal.
A.7.2.3.4. The design of a slab gate valve shall consider the use of non-metallic seals, mounted on seats and stem,
according to the materials specified in the VDS.
A.7.2.4.1. This item presents typical configurations for gate valves, as a result of combinations of materials and features.
The following configurations are considered to create a specific VDS.
A.7.2.4.2. The referred number of the typical configuration of a gate valve, shown on the first column of Table A.36,
Table A.37 and Table A.38, shall be considered as a part of the valve code, according item A.11.5.
A.7.2.4.3. TRIM MATERIAL CONFIGURATION FOR SOLID WEDGE GATE VALVES
Table A.36 – TRIM material configuration for solid wedge gate valves
Material API 600 TRIM

Body Material Gate Material Seat Material Stem Material
Class Number
ASTM A105
Trim Number 8 Stellite ASTM A276
or AISI 410
(API 600 / 602) (Co-Cr Alloy) (UNS S41000)
Carbon ASTM A216 Gr. WCB
Steel ASTM A105
Trim Number 5 Stellite Stellite ASTM A276
or
(API 600 / 602) (Co-Cr Alloy) (Co-Cr Alloy) (UNS S41000)
ASTM A216 Gr. WCB
- Rev. 13 - Page 43 of 84
DISCIPLINE: PIPING
Material API 600 TRIM

Body Material Gate Material Seat Material Stem Material
Class Number
ASTM A350 LF2 Cl 1

Trim Number 16 Stellite ASTM A276
or AISI 316
(API 600 / 602) (Co-Cr Alloy) (UNS S31803)
ASTM A352 Gr. LCC
ASTM A105 ASTM A276
ASTM A995 Gr. 1b ASTM A995 Gr. 1b
or (UNS S32550)
ASTM A216 Gr. WCB -
ASTM A276
+ ASTM A995 Gr. 4a ASTM A995 Gr. 4a
(UNS S31803)
Organic Coating
ASTM A182 Gr. F316
Stainless or Trim Number 16 Stellite
AISI 316 A276 316 / 316L
Steel ASTM A351 Gr. (API 600 / 602) (Co-Cr Alloy)
CF8M
ASTM A182 F51
ASTM A276
or - UNS S31803 UNS S31803
(UNS S31803)
ASTM A995 Gr. 4a
Duplex Steel
ASTM A182 F55
ASTM A276
or - UNS S32760 UNS S32760
(UNS S32760)
ASTM A995 Gr. 6a
ASTM B564 ASTM B564 ASTM B564 ASTM B637
Nickel Alloy -
(UNS N06625) (UNS N06625) (UNS N06625) (UNS N07718)
Bronze
ASTM B61 ASTM B61 ASTM B61
ASTM B61 -
(UNS C92200) (UNS C92200) (UNS C92200)
(UNS C92200)
Gray Iron ASTM B62 ASTM B62 ASTM B62
Uncommon -
ASTM A126 Cl. B (UNS C83600) (UNS C83600) (UNS C83600)
Materials
Nickel Aluminum
Bronze ASTM B148 ASTM B148 ASTM B150
-
ASTM B148 (UNS C95800) (UNS C95800) (UNS C63200)
(UNS C95800)
A.7.2.4.4. OBTURATOR TYPE
Table A.37 – Obturator type for gate valves
Obturator type
0 Solid wedge
1 Slab gate
2 Expanding gate
3 Flexible wedge
A.7.2.4.5. TRIM DESIGN
- Rev. 13 - Page 44 of 84
DISCIPLINE: PIPING
Table A.38 – Trim selection
TRIM design
1 Standard Trim
2 Alternative Trim
3 Special Trim
F Standard Trim, with fugitive emission
A.7.2.5. GATE VALVES ACCORDING TO IOGP S-611
A.7.2.6. GATE VALVES INCLUDED IN SCOPE OF S-611 SHALL COMPLY WITH S-611 AND FOLLOWING
REQUIREMENTS/MODIFICATIONS.
A.7.2.7. DESIGN VALIDATION SHALL BE AS REQUIRED BY TABLE A.3.
A.7.2.8. PROCESS FABRICATION FOR BODY MATERIALS SHALL BE ACCORDING TO TABLE A.7.
A.7.2.9. FIRST PARAGRAPH OF S-611 ITEMH.3.5 SHALL BE READ AS: VALVES SHALL BE TESTED WITH
FULL PRESSURE END THRUST EFFECT TO CHECK THE EFFECTIVENESS OF BODY JOINTS AND
TIGHTNESS AS PER TABLE H.5. TEST SHALL BE CARRIED OUT WITH HORIZONTAL FLOW BORE
AND STEM HORIZONTAL TO DEMONSTRATE COMPLIANCE WITH 5.6.3/5.6.5 (API 600/APII 603).
FOR THIS SELECTED VALVE FROM TABLE H.5, FUNCTIONAL TEST IN ACCORDANCE WITH
H.3.6.2, EXCEPT STEP (A) (2), SHALL BE CARRIED OUT OVER FIVE CYCLES.
A.7.2.10. NDE, TESTS AND DOCUMENTATION OF EACH VALVE SHALL BE ACCORDING A.7.2.11 TO A.7.2.14.
A.7.2.11. VSL-1 VALVES SHALL COMPLY WITH S-611 QSL-1 REQUIREMENTS;
A.7.2.12. VSL-2 VALVES SHALL COMPLY WITH S-611 QSL-2 OR QSL-2G REQUIREMENTS AS APPLICABLE;
A.7.2.13. VSL-3 VALVES SHALL COMPLY WITH S-611 QSL-3 OR QSL-3G REQUIREMENTS AS APPLICABLE;
A.7.2.14. VSL-4 VALVES SHALL COMPLY WITH S-611 QSL-4 REQUIREMENTS.
A.7.3. CHECK VALVE

A.7.3.1.1. Check valves, with flanged or butt weld ends, shall have face to face dimensions according to ASME B16.10.
a) Flanged ends: according to ASME B16.5 up to DN 600 (NPS 24) for ASME classes 150 to 1500, and up to DN
300 (NPS 12) for class 2500; according to ASME B16.47 Series A from DN 650 (NPS 26) up to 1500 (NPS 60)
for ASME Classes 150 to 600, and from DN 650 (NPS 26) up to DN 1200 (NPS 48) for ASME Class 900;
according to ISO 27509 for DN 350 (NPS 14) up to DN 500 (NPS 24) for ASME Class 2500.
A.7.3.1.3. For other materials not specified in the VDS, such as bolts, nuts, washers and lock pins, it shall be considered
the use of materials with similar corrosion resistance than the materials indicated for the internals.
A.7.3.1.4. Whenever specified in the VDS, the manufacturer shall attend to the coating, such as metallic coating, hard
- Rev. 13 - Page 45 of 84
DISCIPLINE: PIPING
coating and/or organic coating specified for some parts and sealing surfaces. In this case, the manufacturer shall attend
the applicable requirements listed on item A.8.2.
A.7.3.1.5. In case the design of a check valve considers the use of drain and vent ports, the plugs shall be specified
considering the alert given in item A.6.1.1.10.
A.7.3.2.1. The following standards shall apply to the design of check valves:
Table A.39 – Design Standards for check valves
Description Casting Forging Forging Forging or Casting Forging

Flanged or Flanged or Butt
Flanged, wafer and lug Flanged
Screwed End Socket weld welding
DN 15 up to 40 15 up to 40 25 up to 40 50 up to 1200 50 up to 1050 50 up to 600 50 up to 300 50 up to 254
(NPS) (1/2 up to 1 1/2) (1/2 up to 1 1/2) (1 up to 1 1/2) (2 up to 48) (2 up to 42) (2 up to 24) (2 up to 12) (2 up to 10)
Class 150, 200 800 and 1500 2500 150 and 300 600 900 and 1500 2500 10.000 psi
ASME
Standard MSS SP-80 API 602
B16.34 LTD
API 594, API 6D API 6A
A.7.3.3.1. For the design of soft seated dual plate check valve, the VDS contains indication about the non-metallic
group material that shall be considered in the valve design, in this case:
- Group A – Terpolymer of VF2, HFP e TFE with fluor content of ~ 67 - 70% or HNBR with %ACN between 36
and 40%. E.g.: Viton B (DuPont), Technoflon TN (Solvay Solexis);
Table A.40 – Seal group materials for soft seated dual plate check valve
Operating Design
Seals Temp. 1 Temp. 2 Seals Seals Group
Application RGD Suitable for
Group Min. Max. Min. Max. Materials Design Restrictions
(° C) (° C) (° C) (° C)
Water, Utility, Amines, Steam,

O-ring
Normal HNBR Sweet Aromatic
Group A 0 +150 0 +170 Polypak No
Temperature FKM Type 2 hydrocarbon and
Gasket
Chemicals hydrocarbons 3
1 Temperature range considered for continuous service without reducing the seals' economic life or its sealing capability.
2 Temperature range considered whether the seals may be exposed for a short period of time (transient temperature spike),
under a static condition (without operation), with a possible leakage but without permanently damaging the sealing system.
A.7.3.4.1. This item presents typical configurations for check valves, as a result of combinations of materials and
features. The following configurations are considered to create a specific VDS.
A.7.3.4.2. The referred number of the typical configuration of a check valve, shown on the first column of Table A.41,
- Rev. 13 - Page 46 of 84
DISCIPLINE: PIPING
Table A.42 and Table A.43, shall be considered as a part of the valve code, according item A.11.5.
A.7.3.4.3. TRIM MATERIAL ACCORDING TO MATERIAL CLASS
Table A.41 – TRIM material according to material class
Soft Sealing Metal-to-metal Sealing

Material Class Body Material
Primary TRIM Primary TRIM ¹ Secondary TRIM ²
ASTM A105
Trim Number 1 Trim Number 8 Trim Number 5
Carbon Steel or
(API 594) (API 594) (API 594)
ASTM A216 WCB
ASTM A350 LF2 Cl.1
Low Temperature Trim Number 10 Trim Number 12
or N/A
Carbon Steel (API 594) (API 594)
ASTM A352 LCC
ASTM A182 F316
Trim Number 10 Trim Number 12
Stainless Steel or N/A
(API 594) (API 594)
ASTM A351 CF8M
Duplex Steel
ASTM A995 Gr. 1b ASTM A995 Gr. 1b N/A N/A
(Onshore)
ASTM A182 F51 ASTM A182 F51 ASTM A182 F51
Duplex Steel
or or or N/A
(Offshore)
ASTM A995 Gr. 4a ASTM A995 Gr. 4a ASTM A995 Gr. 4a
ASTM A182 F55 ASTM A182 F55 ASTM A182 F55
Superduplex Steel or or or N/A
ASTM A995 Gr. 6a ASTM A995 Gr. 6a ASTM A995 Gr. 6a
ASTM A350 LF3
or ASTM A350 LF3
Alloy Steel ASTM A352 LF3 +
N/A N/A
(ASTM A333 Gr.3) + Alloy 625
Alloy 625 (UNS N06625)
(UNS N06625)
Alloy Steel
ASTM A522 Type I N/A ASTM A522 Type I N/A
(ASTM A333 Gr.8)
Alloy Steel ASTM A522 Type I ASTM A522 Type I
(ASTM A333 Gr.8) + +
N/A N/A
with nickel-based Alloy 625 Alloy 625
alloy cladding (UNS N06625) (UNS N06625)
Nickel Aluminum ASTM B148 ASTM B148
N/A N/A
Bronze (UNS C95800) (UNS C95800)
TRIM AA
Gray Iron ASTM A126 Cl B N/A N/A
(API 594)
- Rev. 13 - Page 47 of 84
DISCIPLINE: PIPING
Table A.42 – Obturator type for check valves
Config.
# Type
0 Piston
1 Dual plate
2 Swing
3 Axial non-slam
4 Ball
5 Swing, spring loaded, non-slam
6 Manufacturer standard
A.7.3.4.5. TRIM SELECTION
Table A.43 – TRIM selection
Config.
# Type Body Construction
1 Primary TRIM (Soft) Wafer
2 Primary TRIM (Metal x Metal) Wafer
3 Secondary TRIM (Metal x Metal) Wafer
4 Alternative TRIM Wafer
Double Flanged Short Pattern or
5 Primary TRIM (Metal x Metal)
Studded End (API 6A)
6 Lined Flanged
A.7.4. GLOBE VALVE

A.7.4.1.1. It shall be considered a metal-to-metal seated design for all types of globe valve.
coating, hard coating and/or organic coating specified for some parts and sealing surfaces, such as in the body, etc. In
this case, the manufacturer shall attend the applicable requirements listed on item A.8.2.
A.7.4.1.3. Globe valves, with flanged or butt weld ends, shall have face to face dimensions according to ASME B16.10.
a) Flanged ends: According ASME B16.5 up to DN 600 (NPS 24) for ASME classes 150, 300, 600 and 900,
according to ASME B16.47 Series A from DN 650 up to DN 1500 (NPS 26-60) for and from DN 650 up to DN
1200 (NPS 26-48) for ASME class 900.
A.7.4.2.1. The following standards shall apply to the design of globe valves:
Table A.44 – Design Standards for globe valves
- Rev. 13 - Page 48 of 84
DISCIPLINE: PIPING

Description Forging Casting or Forging
Socket Weld Butt Weld Flange
DN a 15 up to 40 25 up to 40 50 up to 400
(NPS) (1/2 up to 1 1/2) (1 up to 1 1/2) (2 up to 24)
Class 800 and 1500 2500 150 up to 2500
Standard API 602 ASME B16.34 LTD BS 1873 or API 623
A.7.4.3.1. This item presents typical configurations for globe valves, as a result of combinations of materials and
features. The following configurations are considered to create a specific VDS.
A.7.4.3.2. The referred number of the typical configuration of a globe valve, shown on the first column of Table A.45
and Table A.46, shall be considered as a part of the valve code, according item A.11.5.
A.7.4.3.3. TRIM MATERIAL CLASS CONFIGURATION
Table A.45 – TRIM design code for globe valves
Metal-to-metal
Metal-to-metal Sealing Sealing, alternative
face type
Primary TRIM ¹ Secondary TRIM Primary TRIM ¹
1 2 3
ASTM A105
CR13 and HF HF
Carbon Steel or
(BS 1873) (BS 1873)
ASTM A216 WCB
ASTM A105
Carbon Steel
or ASTM A995 Gr. 4a ASTM A995 Gr 1b
with organic coating
ASTM A216 WCB
ASTM A350 LF2 Cl.1
Low Temperature N/A
or AISI 316 + Stellite
Carbon Steel
ASTM A352 LCC
ASTM A182 F316L
Stainless Steel or AISI 316 + Stellite N/A
ASTM A351 CF8M
ASTM A182 F51 ASTM A182 F51
Duplex Steel or or N/A
ASTM A995 Gr. 4a ASTM A995 Gr. 4a
ASTM A182 F55
ASTM A182 F55 ASTM A182 F55 or
Super duplex Steel or or N/A ASTM A995 Gr. 6a
ASTM A995 Gr. 6a ASTM A995 Gr. 6a
ASTM A350 LF3

Alloy Steel
or ASTM A350 LF3 N/A
(ASTM A333 Gr.3)
ASTM A352 LF3
Alloy Steel ASTM A522 Type I ASTM A522 Type I N/A
- Rev. 13 - Page 49 of 84
DISCIPLINE: PIPING
Metal-to-metal
Metal-to-metal Sealing Sealing, alternative
face type
Primary TRIM ¹ Secondary TRIM Primary TRIM ¹
1 2 3
(ASTM A333 Gr.8)

Nickel Aluminum ASTM B148 NAB
N/A
Bronze (UNS C95800) (BS 1873)
Table A.46 – Obturator type for globe valves
Config.
# Type
0 Bevelled disc
1 Angular
A.7.5. BUTTERFLY VALVE

A.7.5.1.1. It shall be considered the following types of butterfly valves: Category A (concentric), Category B (Double
offset) and Category B (Triple Offset).
A.7.5.1.2. All butterfly valves category B with triple offset shall consider a metal-to-metal seated design.
coating and/or hard coating specified for some parts and sealing surfaces, such as in the body or disc. In this case, the
manufacturer shall attend the applicable requirements listed on items A.7.5.4.3 and A.8.2.
A.7.5.1.4. Butterfly valves and its actuators shall be designed and tested considering the maximum differential pressure
equal to the maximum pressure rating of the associated flange class.
A.7.5.2.1. The following standards shall apply to the design of butterfly valves:
- Rev. 13 - Page 50 of 84
DISCIPLINE: PIPING
Table A.47 – Design Standards for butterfly valves
Category A Category B
Description Concentric Double offset Triple offset
Lug Lug Flanged (Short Pattern) Flanged (Short Pattern)
Ductile Iron Forging or Casting Forging or Casting
DN a 50 to 1200 50 to 600 50 to 1200 50 to 600 50 to 1200 50 to 600

(NPS) (2 to 48) (3 to 24) (3 to 48) (3 to 24) (2 to 48) (2 to 24)
Maximum Working
Class 150 up to 600 150 up to 300 600 150 up to 300 600
Pressure (MWP)
Standard API 609
A.7.5.3.1. For the design of seats / stem seals, in butterfly valves Category A or B, the following materials shall be
considered:
Table A.48 – Non-metallic materials for seats / stem seal design
Minimum Maximum
Type Material
Temp. (ºC) Temp. (ºC)
NBR -10 +80
Category A
FKM -10 +150
Category B (Double Offset) RPTFE -46 +260
Category B (Triple Offset) Graphite -240 +550
Note: Temperature values listed in Table A.48 represents the limits of use the non-metallic material on a butterfly valve
design.
A.7.5.4. MATERIAL CONFIGURATION
A.7.5.4.1. CATEGORY B (TRIPLE OFFSET) CONFIGURATION
A.7.5.4.2. For the design of butterfly valves category B (triple offset), it may be considered one of the following
configurations:
- Rev. 13 - Page 51 of 84
DISCIPLINE: PIPING
(a) Seal ring fixed to body & hard coating on disc (b) Seal ring fixed to disc & hard coating on body
Figure A.10 – Illustration of typical category B (triple offset) seat configurations
A.7.5.4.3. METALLIC COATING
Whenever AISI 410 is considered as disc material for category B butterfly valves, it shall be applied
ENP coating on disc sealing surface.
On triple offset butterfly valves (category B), it shall be applied metallic coating on sealing surface (disc
or body, depending on configuration as described in Figure A.10). In this case, the use of Cobalt-Chromium (Co-Cr)
weld overlay or ENP are acceptable.
All metallic coatings application shall attend the specific requirements listed in item A.8.2.1.
A.7.5.5.1. MATERIAL CLASS CONFIGURATION
Table A.49 – Material class configuration for butterfly valves
Material Disc
Body Material Type Seats 1 Stem Seal Ring
Class Material
AISI 410
Category B ASTM A276
+ RPTFE N/A
ASTM A105 (Double Offset) (UNS S41000)
Carbon ENP
or
Steel ASTM A216 Gr. WCB
AISI 316 ASTM A564
Category B Graphite Laminated
AISI 316 + Type 630
(Triple Offset) with AISI 316
Hard Coating (UNS S17400)
ASTM B148 ASTM B865
NBR N/A
(UNS C95800) (UNS N05500)
ASTM A536
Gr 65-45-12 ASTM A276
NBR N/A
ASTM A536 Category A + (UNS S41000)
Ductile Iron Gr 65-45-12 (Concentric) PA Coating
ASTM A536
Gr 65-45-12 ASTM A276
NBR N/A
+ (UNS S31803)
PA Coating
Low Category B AISI 316 ASTM A564 Graphite Laminated
ASTM A352 Gr. LCC AISI 316
Temperature (Triple Offset) + Type 630 H1150 with AISI 316
- Rev. 13 - Page 52 of 84
DISCIPLINE: PIPING
Material Disc
Body Material Type Seats 1 Stem Seal Ring
Class Material
Carbon Hard Coating (UNS S17400)
Steel
ASTM A564
Stainless Category B Graphite Laminated
ASTM A351 CF8M AISI 316 RPTFE Type 630 H1150
Steel (Double Offset)
(UNS S17400)
with AISI 316
Category B Duplex ASTM A276

RPTFE N/A
(Double Offset) (UNS S31803) (UNS S31803)
Duplex
Duplex Steel ASTM A995 Gr. 4a
Category B Duplex (UNS S31803) ASTM A276 Graphite Laminated with
(Triple Offset) (UNS S31803) + (UNS S31803) Duplex (UNS S31803)
Hard Coating
Category B Super duplex ASTM A276
RPTFE N/A
(Double Offset) (UNS S32760) (UNS S32760)
Super Super duplex
ASTM A995 Gr. 6a
duplex Steel Category B Super duplex (UNS S32760) ASTM A276 Graphite Laminated with
(Triple Offset) (UNS S32760) + (UNS S32760) Super duplex (UNS S32760)
Hard Coating
Category B ASTM B148 ASTM B865

RPTFE N/A
(Double Offset) (UNS C95800) (UNS N05500)
Nickel
ASTM B148
Aluminum ASTM B148
(UNS C95800)
Bronze Category B ASTM B148 (UNS C95800) ASTM B574 Graphite Laminated with
(Triple Offset) (UNS C95800) + (UNS N10276) Hastelloy (UNS N10276)
Hard Coating
1
For all triple offset butterfly valves (category B), the VDS have taken into consideration typical configuration “(a) Seal ring fixed to body
& hard coating on disc”, as described in Figure A.10. Adequate adjustments shall be made for use of configuration “(b) Seal ring fixed to
disc & hard coating on body”.
A.7.5.5.2. DISC & SEAT CONFIGURATION
Table A.50 – Disc & Seat Configuration for butterfly valves

Config. Category
# (Ref. API 609) Disc & Seat Configuration
0 Category A Concentric, trim 1 (monel)

1 Category B Double offset (bi-eccentric), soft-seated
2 Category B Triple offset (tri-eccentric)
3 Category B Double offset (bi-eccentric), metal-seated
4 Category A Concentric, trim 2 (410)
5 Category B Double offset (bi-eccentric), soft-seated, fire-tested
6 Category B Triple offset (tri-eccentric), fire-tested
7 Category B Double offset (bi-eccentric), metal-seated, fire-tested
8 Category A Concentric, trim 3 (22 CR)
9 Category A Concentric, trim 4 (NAB)
F Category B Double offset (bi-eccentric), soft-seated, fire-tested, fugitive emission
U Category B Triple offset (tri-eccentric), fire-tested, fugitive emission
G Category B Double offset (bi-eccentric), metal-seated, fire-tested, fugitive emission
- Rev. 13 - Page 53 of 84
DISCIPLINE: PIPING
A.7.5.5.3. END CONNECTION
Table A.51 – End connection configuration for butterfly valves

Double
Face type Lug Flanged
(Short Pattern)
RF 1 3
FF 4 6
RTJ 7 9
A.7.6. NON-METALLIC VALVE

A.7.6.1. TYPICAL CONFIGURATION
A.7.6.1.1. MATERIAL CONFIGURATION
Table A.52 – Material configuration for non-metallic valves
Config.
# Material
01 PVC
02 CPVC
03 FRP
A.7.6.2. DESIGN REQUIREMENTS FOR NON-METALLIC VALVE
A.7.6.2.1. The design of non-metallic ball valve shall consider the minimum pressure – temperature rating as follows:
Table A.53 – Minimum pressure (psig) – temperature rating for non-metallic ball valves
Material PVC CPVC FRP

DN (NPS) DN (NPS) DN (NPS)
Temp.
1/2 up to 1 1/2 ≥2 1/2 up to 1 1/2 ≥2 1/2 up to 1 1/2 2 up to 3 4 up to 10
23°C 250 150 250 150 275 250 150
30°C 235 150 250 150 275 250 150
35°C 212 150 245 150 275 250 150
40°C 192 144 232 146 250 225 140
45°C 211 137 250 225 140
50°C 188 128 250 225 140
55°C 179 119 250 225 140
60°C N/A 170 101 250 225 140
65°C 161 92 250 225 140
70°C 140 83 232 210 130
80°C 134 74 232 210 130
A.7.6.2.2. The design of non-metallic check valve shall consider the minimum pressure – temperature rating as follows:
Table A.54 – Minimum pressure (psig) – temperature rating for non-metallic check valves
- Rev. 13 - Page 54 of 84
DISCIPLINE: PIPING
Material
PVC CPVC
Temp.
23°C 150 150
30°C 150 150
35°C 150 150
40°C 144 146
45°C 137
50°C 128
55°C 119
60°C 110
N/A
65°C 101
70°C 92
75°C 83
80°C 74
A.7.6.2.3. The design of non-metallic butterfly valve shall consider the minimum pressure – temperature rating as
follows:
Table A.55 – Minimum pressure (psig) – temperature rating for non-metallic butterfly valves
Material
PVC CPVC
Temp.
23°C 150 150
30°C 132 140
35°C 115 129
40°C 97 119
45°C 108
50°C 98
55°C 87
60°C 77
N/A
65°C 66
70°C 56
75°C 45
80°C 35
A.8. MATERIALS & FABRICATION

A.8.1. REQUIREMENTS FOR CASTING OF DUPLEX & SUPERDUPLEX
A.8.1.1. SCOPE
A.8.1.1.1. All valves made from stainless steel duplex and/or super duplex casting (UNS J92205, UNS J93404 and
UNS J93380), without using bake sand foundry process, shall attend the minimum requirements listed herein for design,
production, inspection and acceptance.
A.8.1.1.2. The requirements listed herein are applicable for axial, ball, gate, globe and check type flanged valves, for
all pressure classes, with NPS ≥ 2.
- Rev. 13 - Page 55 of 84
DISCIPLINE: PIPING
A.8.1.2. DOCUMENTATION
A.8.1.2.1. The Data Book of the valve shall contain all certificates related to all parts, according:
- chemical requirements;
- mechanical tests (tension, hardness and impact);
- metallurgic tests (resistance to localized corrosion and metallography for phase treatment counting and thermal
treatment of the pilot casting);
- inspection reports (visual, using penetrant liquid and radiography);
- all thermal treatments;
- all WPS for defect repairing, approved by PETROBRAS or by a Classification Society indicated by
PETROBRAS.
- welders qualification certificates, for repairs execution;
- cavity mapping, for bigger repairs of each part of the valve;
- welding report, for repairs of each part of the valve.
A.8.1.3. CHEMICAL REQUIREMENTS
A.8.1.3.1. The duplex steel used for manufacturing casting valves, for use in piping specifications B16, C16, E16, G16
or G16P, shall be in accordance with ASME SA-995 or ASTM A 995 Grade 4A (UNS J92205 or ACI CD3MN).
A.8.1.3.2. The super duplex steel used for manufacturing casting valves, for use in piping specifications B12, C12, H12,
G12, G12P or J12, shall be in accordance with ASME SA-995 or ASTM A 995 Grade 5A (UNS J93404 or ACI CE3MN).
A.8.1.3.3. The super duplex steel used for manufacturing casting valves, for use in piping specifications B13 or C13,
shall be in accordance with ASME SA-995 or ASTM A 995 Grade 6A (UNS J93380 or CD3MWCuN).
A.8.1.3.4. The representative sample of the chemical requirements of the valve shall be collected from the pouring
ladle.
A.8.1.3.5. A representative sample for carbon, sulfur and nitrogen contents shall be collected from the furnace before
pouring into the ladle.
A.8.1.3.6. The addition of Niobium to the cast shall be avoided. The maximum allowable content of Niobium shall be
0,060% at the chemical requirements of the cast.
A.8.1.3.7. Adding Aluminum to the run shall be avoided. The maximum allowable content of Aluminum to the final
chemical requirements shall 0,030%.
A.8.1.3.8. The levels of Nitrogen shall preferably be in the range of 0,20% up to 0,25%.
A.8.1.3.9. All consumables for the welding process shall have certification of their chemical requirements guaranteeing
maximum levels of Niobium of 0,060%.
A.8.1.3.10. The chemical analysis of the elements shall be made in calibrated equipment according certified standards.
A.8.1.3.11. Whenever more than one ladle is used for one mold, the metal founded in each ladle shall be in accordance
with the chemical specifications for the required level.
A.8.1.4. HEAT TREATMENT
A.8.1.4.1. The procedure for solubilization heat treatment used to the super duplex steel casting valves shall be in
accordance with ASME SA-995 or ASTM A 995 Grade 5A (UNS J93404 or ACI CE3MN) and Grade 6A (UNS J93380
- Rev. 13 - Page 56 of 84
DISCIPLINE: PIPING
or ACI CD3MWCuN).
A.8.1.4.2. Solubilization heat treatment is the only acceptable treatment for production of the super duplex steel casting
valves.
A.8.1.4.3. The maximum number of solubilization heat treatments allowed for a single valve is limited to three (03) at
foundry and one (01) at machining shop. If more heat treatments are needed, the manufacturer shall submit it for
PETROBRAS approval.
A.8.1.4.4. All heat treatments shall be monitored through thermocouples in the heat charge and in the furnace, and its
register shall be inserted into the Data Book.
A.8.1.4.5. Welding repair is not allowed before heat treatment.
A.8.1.4.6. Whenever solubilization heat treatment is necessary after casting, it shall be performed in order to avoid
distortions of the piece. It may be executed only one time.
A.8.1.4.7. The soaking time depends on the prior experience of the manufacturer, and shall guarantee full solubilization
of the inter-metallic phases and the precipitates through the thickest dimension of the piece without causing dimensional
distortions.
A.8.1.4.8. The pilot casting shall have possibility of extracting a test specimen for metallographic tests, which can be in
any direction (longitudinal or transversal), representing a central session of the thickest part of the piece, according
supplementary requirement S26.2 of ASTM A703, in order to verify the effectiveness and adjustment of the soaking time
of the solubilization heat treatment. The results of this metallographic shall be part of the Data Book.
A.8.1.4.9. The result of the metallographic test shall indicate absence of inter-metallic phases and undesired
precipitates – notably, the sigma phase, carbides and nitrates – in a 200X magnification, as well as indicate a level of
ferrite in the range of 35 to 55%, according ASTM E 562.
A.8.1.4.10. For each casting with weight ≥ 300 kg, specimens for mechanical and metallurgical tests shall be attached,
according ASTM A703. These test specimens shall remain attached to the casting until the last thermal treatment. For
pieces with weight < 300 kg, a test specimen per run is accepted.
A.8.1.5. MECHANICAL AND METALLURGICAL TESTS
A.8.1.5.1. The mechanical and metallurgical tests shall be done after the last the solubilization heat treatment, and
before machining the casting.
A.8.1.5.2. The mechanical tests to be performed are tension, hardness and impact (Charpy-V) testing, according ASTM
A370.
A.8.1.5.3. The test specimens shall be obtained from cast test blocks, according to ASTM A703. These blocks shall go
through all the solubilization heat treatments before collecting the specimens for analysis.
A.8.1.5.4. One (01) test specimen shall be extracted for the tension test. The minimum acceptable values are according
Table A.56 (ref. ASME SA-995 or ASTM A995).
Table A.56 – minimum values for tension tests
Grade 4A 5A 6A
UNS J92205 J93404 J93380
Tensile Strength, ksi [Mpa] {kg/mm²} 90 [620] {63} 100 [690] {70} 100 [690] {70}
Yield Strength, ksi [Mpa] {kg/mm²} 60 [414] {42} 75 [515] {53} 65 [450] {46}
- Rev. 13 - Page 57 of 84
DISCIPLINE: PIPING
Grade 4A 5A 6A
Elongation in 2” [50 mm], % 25 18 25
A.8.1.5.5. Three (03) test specimens shall be collected for the impact tests (Charpy-V). The tests shall be performed at
a temperature of -46°C. The minimum values of absorbed energy shall be of 45J for an average of the three test
specimens and 35J for each one of the test specimens.
A.8.1.5.6. The hardness tests shall be run on a test specimen collected from a test block, in a point representative of
the central part of the thickest part of the casting, according to the supplementary requirement S26.2 of ASTM A703.
The maximum hardness shall not be above 32 HRC (or 310 HB or 330 HV10), considering the average of three
measurements. Castings with weight < 300 kg shall be tested individually and shall render specific hardness values less
or equal to the pilot casting on the surface.
A.8.1.5.7. A test specimen shall be collected from the pilot casting, in order to perform the corrosion tests according
ASTM G48 Method A. The test shall be run for 24 hours at a temperature of 50°C. The acceptance criteria shall be
according to Grade 5A (UNS J93404 or CE3MN) and Grade 6A (UNS J93380 or CD3MWCuN):
- no pites located at 20 X magnification;
- loss of mass less than 4,0 g/m².
A.8.1.5.8. The test to define the levels of ferrite shall be performed according to ASTM E562. The test specimen shall
be collected from a cast test block connected to a casting that would represent a certain run. The acceptable range is
35 up to 55% of ferrite.
A.8.1.6. CASTING INSPECTION
A.8.1.6.1. VISUAL
visual inspection shall be made on all castings before and after each solubilization heat treatment, after
pre-machining (whenever applicable) and the final machining.
all accessible surfaces, internal and/or external, shall be visually examined, comparing acceptable
discontinuities and superficial finishing according MSS SP-55 or comparison rules of Steel Casting Research and
Trading Association (SCRATA) adopted in ASTM A802, or other standard considered equivalent by a set deal between
the manufacturer and PETROBRAS.
the levels of acceptance for visual inspections are set in ASTM A802, and are:
- level II, for non-machined surfaces;
- level III, for surfaces to be machined, as long as the machining completely eliminates the discontinuities.
all castings that presents, in one or more surfaces, independent of how serious or how extensive the
defects are, or whether it allows repairs using welding or not, the following defects shall be considered
UNACCEPTABLE:
- chaplet - discontinuity due to the incomplete fusion of the supports of chills and cores;
- shrinkage - cavity resulting from contraction while solidifying;
- shift - discontinuity due to displacement of contact edges of the molding boxes;
- misrun - insufficient foundered metal in the casting;
- shut metal - discontinuity due to the encounter of two currents of metal that have not been well mixed;
- Rev. 13 - Page 58 of 84
DISCIPLINE: PIPING
- veins - discontinuity due to movement or cracking of the sand mold;

- rat tail - depression on the surface of the piece caused by waves or failure in the mold surface;
- internal chills - discontinuity caused by incomplete fusion of devices used to increase the cooling rate in
determined places.
A.8.1.7. LIQUID PENETRANT INSPECTION (LPI)
A.8.1.7.1. LPI shall be performed by Level 2 inspectors qualified by the “Sistema de Nacional de Qualificação e
Certificação” (National System of Qualification and Certification) in Non Destructive Testing (SNQC/END), or by another
bureau according to ISO 9712 or EN 473.
A.8.1.7.2. LPI shall be performed on every produced casting, on all accessible surfaces (internally and/or externally),
after the final machining. All castings that make up the valves of the same order shall undergo inspection using Liquid
penetrant.
A.8.1.7.3. LPI shall be performed according to ASTM E165.
A.8.1.7.4. indications shall be classified according to APPENDIX 8 (8-3) of ASME SEC VIII Div. 1.
A.8.1.7.5. The acceptance criteria shall be according to ASME SEC VIII DIV 1 APPENDIX 7.
A.8.1.8. RADIOGRAPHY OF VALVE PARTS AND PILOT CASTING
A.8.1.8.1. radiographic inspection shall be executed by Level 2 inspectors qualified by the “Sistema de Nacional de
Qualificação e Certificação” (National System of Qualification and Certification) in Non Destructive Testing (SNQC/END),
or by certification according to ISO 9712 or EN 473.
A.8.1.8.2. radiographic inspection shall be performed on the pilot casting (body, cap and shutter), after conclusion of
heat treatment. For parts which pressure classes are 900 and above, it is mandatory to perform radiographic inspection
on 100% of the final pieces, in the critical regions defined in ASME B16.34.
A.8.1.8.3. radiographic inspection shall be performed according to ASTM E94 and ASTM E1030.
A.8.1.8.4. The list of parts to be radiographed and the acceptance criteria shall be according to ASME B16.34.
A.8.1.8.5. If all indications are classified as ACCEPTABLE, no other piece than the pilot casting shall be radiographed.
A.8.1.8.6. If one or more conditions were classified UNACCEPTABLE, the pilot casting shall be fixed or scrapped, a
report shall be issued with causes analyses and solutions, and another piece shall be radiographed. If the second piece
is approved, no more piece needs to be radiographed. If the second piece also presents UNACCEPTABLE indications,
all pieces equal to the pilot casting of the order shall be radiographed in the areas rejected for the pilot casting and for
the second casting. The second casting and the subsequent piece of the order shall be repaired whenever identified an
unacceptable indication, otherwise it shall be rejected.
Table A.57 - maximum levels of severity by defect by thickness
Defects by
Thickness < 2” 2 ≤ Thickness < 4 1/2” 4 1/2” ≤ Thickness < 12”
Thickness
Standards ASTM E446 ASTM E186 ASTM E280
Porosity (A) A2 A3 A3
Sand or Slag (B) B3 B3 B3
Shrinkage CA2 CA3 CA3
- Rev. 13 - Page 59 of 84
DISCIPLINE: PIPING
Porosity (CA)
Shrinkage
CB3 CB3 CB3
Porosity (CB)
Shrinkage
CC3 CC3 CC3
Porosity (CC)
Shrinkage
CD3 - -
Porosity (CD)
Cracks (D) None None None
Shrinkage
None None None
Cracks (E)
Inserts (F) None None None
A.8.1.9. ULTRASONIC INSPECTION
A.8.1.9.1. Ultrasonic inspection shall be executed by Level 2 inspectors qualified by the “Sistema de Nacional de
Qualificação e Certificação” (National System of Qualification and Certification) in Non Destructive Testing (SNQC/END),
or by certification according to ISO 9712 or EN 473.
A.8.1.9.2. Ultrasonic inspection shall be performed according to ASTM A388 (forgings) and ASTM A609 (castings).
A.8.1.9.3. Acceptance criteria shall be according to ASME B16.34.
A.8.1.10. REPAIRS
A.8.1.10.1. All kind of repairs shall be made by welding.

A.8.1.10.2. All repairs shall have a specific WPS approved by welding inspector level 2, according to type of equipment,
and by a Classification Society indicated by PETROBRAS. This WPS shall be based on ASTM A488.
A.8.1.10.3. The WPS and the qualification of the welder shall be according to acceptance criteria established in I-ET-
3010.00-1200-955-P4X-001.
A.8.1.10.4. The repair shall be witnessed by a Level I welding inspector.
A.8.1.10.5. Before any repair, the surface shall be inspected by visual and preferably magnetic particle and liquid
penetrant inspection.
A.8.1.10.6. Twenty-four hours (for hydrogen diffusion) after the last welding repair, it shall be repeated the same NDT
used to identify the defect. For extensions over 50 mm length and over 20% thickness depth a ultrasonic test or
radiography shall be executed. Acceptance criteria shall be according to ASME B16.34.
A.8.1.10.7. It is mandatory to perform post weld heat treatment for carbon steel or solubilization on stainless steel when:
The repair is demanded after leaking in the hydrostatic test;

The cavity after the repair preparation is over 20% of thickness depth or 25 mm, whichever is smaller;
The extension (area) of the cavity is bigger than 65 cm².
A.8.1.10.8. Test Specimens for Counter-Sample - Chemical Analysis and Mechanical Testing: the minimum period
established for storage, by the foundry, of test specimens for sample are twelve (12) months.
A.8.1.11. MACHINING
- Rev. 13 - Page 60 of 84
DISCIPLINE: PIPING
A.8.1.11.1. The machining of the casting shall only be executed after heat treatment.
A.8.1.11.2. No kind of machining may be done after hydrostatic test.
A.8.1.11.3. Machined surfaces shall be according to valve design as tolerance and rugosity.
A.8.1.11.4. No kind of metallurgical changing may occur caused by heating during machining. If necessary, shall be a
metallographic replica exam.
A.8.1.11.5. Liquid penetrant on seal surface shall be ZERO defect.
A.8.2. COATINGS
A.8.2.1. METALLIC COATING
A.8.2.1.1. ELECTROLESS NICKEL PLATING (ENP)
Whenever specified in the VDS, it shall be applied on the indicated parts an ENP coating obtained by
chemical reactions leading to a plating composed of 90% Nickel and 10% Phosphorus. This coating shall be in
accordance with ASTM B 733 attending classification SC4, Type V, heat treatment Class 2.
The minimum thickness of the ENP coating shall be 0,003 inch (75 μm).
All components shall be traceable for the details of the coating procedure, coating conditions and date
of application.
The manufacturer shall issue inspection certificates of the ENP coating, and each certificate shall
identify the plant where the treatment is performed and the history of the process. Also, it shall list all serial numbers of
the parts coated together with the material grades and the overall geometry of those parts.
A.8.2.1.2. COBALT-CHROMIUM (CO-CR) WELD OVERLAY
Whenever specified in the VDS the term Stellite, it shall be applied a weld overlay of cobalt-chromium
(Co-Cr) alloy on indicated parts.
The specification of the cobalt-chromium (Co-Cr) alloy shall fulfil the requirements of the design standard
indicated in the VDS.
For valves with DN < 2 , which is not possible to apply cobalt-chromium (Co-Cr) weld overlay, the
manufacturer shall consider to use integral parts of cobalt-chromium (Co-Cr) alloy.
For the parts which materials are made of solid cobalt-chromium (Co-Cr) alloy there is no need to apply
an overlay.
A.8.2.1.3. STAINLESS STEEL (AISI 316) WELD OVERLAY
Whenever specified in the VDS, it shall be applied a minimum of 3,0 mm thick weld overlay in stainless
steel grade 316L on seat pockets and stem seal contact faces on the body.
For floating ball valves, this requirement is not applicable to the seat pockets as soon as the seat ring
is made of an integral, solid thermoplastic material (i.e.: valves having a fixed seat), but it applies to stem sealing areas
in all cases (for floating ball valves having also a floating seat design, the seat-to-body sealing area shall consequently
be overlaid).
For valves with DN < 2, which is not possible to apply stainless steel weld overlay, the manufacturer
shall consider using integral parts of stainless steel or CRA alloy.
For the parts which materials are made of stainless steel, duplex, super duplex or solid Alloy 625 there
- Rev. 13 - Page 61 of 84
DISCIPLINE: PIPING
is no need to apply an overlay.

Dilution on welded surface shall not exceed 10% of base metal.
A.8.2.1.4. NICKEL ALLOY (INCONEL 625) WELD OVERLAY
Whenever specified in the VDS the term Alloy 625, it shall be applied a weld overlay of a nickel alloy
UNS N06625 on indicated parts.
The areas of such parts that shall be welded are indicated in the VDS. The manufacturer shall attend to
the requirement of partial or full cladding.
The weld overlay thickness shall be sufficient in order to obtain a minimum of 3,0 mm thick protective
layer in the final machined condition.
For valves with DN < 2, which is not possible to apply Alloy 625 weld overlay, the manufacturer shall
consider to use integral parts of Alloy 625.
For the parts which materials are made of solid Alloy 625 there is no need to apply an overlay.
Dilution on welded surface shall not exceed 10% of base metal.
A.8.2.2. HARD COATING
A.8.2.2.1. CHROMIUM ELECTROPLATE
Whenever specified hard coating in the VDS, a hard coating of chromium electroplate may be applied
on the indicated parts of a metal-to-metal ball valve, as described in Table A.32.
A.8.2.2.2. CHROME CARBIDE
Whenever specified hard coating in the VDS, a hard coating of chrome carbide may be applied on the
indicated parts.
When applicable, hard coating of chrome carbide shall be applied by High Velocity Oxy-Fuel (HVOF)
process.
The hard coating of chrome carbide shall achieve a minimum thickness of 200 μm after grinding and
lapping.
The hard coating shall be carefully applied and inspected to ensure that the finish is smooth, fine
grained, adherent, and free from blisters, pits, nodules, indication of burning, edge buildup, and other defects.
The hard Coating thickness shall be measured to confirm the results of it against the specified thickness.
A.8.2.2.3. TUNGSTEN CARBIDE
Whenever specified hard coating in the VDS, a hard coating of tungsten carbide may be applied on the
indicated parts.
When applicable, hard coating of tungsten carbide shall be applied by High Velocity Oxy-Fuel (HVOF)
process.
The hard coating of tungsten carbide shall achieve a minimum thickness of 200 μm after grinding and
lapping.
The hard coating thickness shall be measured to confirm the results of it against the specified thickness.
- Rev. 13 - Page 62 of 84
DISCIPLINE: PIPING
A.8.2.2.4. CHROME-NICKEL SPRAY AND FUSE
Whenever specified hard coating in the VDS, a hard coating of chrome-nickel basis with metallurgical
bonding may be applied on the indicated parts.
When applicable, hard coating of chrome-nickel basis with metallurgical bonding shall be applied by
Flame Spray and Fuse process.
The hard coating of chrome-nickel spray and fuse shall achieve a minimum thickness of 500 μm after
grinding and lapping.
The hard Coating thickness shall be measured to confirm the results of it against the specified thickness.
A.8.2.3. NON-METALLIC COATING
A.8.2.3.1. ORGANIC COATING
The use of valves with organic coating may be considered as option for specific service applications,
such as with seawater service.
Whenever applicable, the pipe specification (spec) may present an organic coated valve code as an
option.
Only ball, gate and globe valve types classified as VSL-1 and VSL-2 may consider the use of organic
coating.
The VDS of organic coated valve shall indicate/allow, as principle, the application of organic coating
only in the body/closure material of the valve.
For small size valves (e.g.: NPS < 3), when organic coating is not applicable, the body may be made of
a material with the same corrosion resistance of the materials specified for the internals.
The specification of the organic coating shall be according to Annex F of this document.
RTJ flanges may be organic coated, except the ring groove which shall attend the orientation indicated
in the pipe specification (spec).
A.8.2.3.2. POLYAMIDE (PA) COATING
The use of valves with polyamide (PA) coating may be considered as option for specific service
applications, such as with seawater service.
Whenever applicable, the pipe specification (spec) may present an polyamide (PA) coated valve code
as an option.
Only concentric butterfly valves (Category A) classified as VSL-1 may consider the use of polyamide
(PA) coating.
The VDS of polyamide (PA) coated valve shall indicate/allow, as principle, the application of polyamide
(PA) coating only in the disc material of the valve.
The acceptable specifications of the polyamide (PA) coating are PA 11 and PA 12.
A.8.3. ALTERNATIVE MATERIALS
A.8.3.1. All materials listed in the VDS shall be considered as standardized materials for valve parts, but are not exclusive
- Rev. 13 - Page 63 of 84
DISCIPLINE: PIPING
solutions. Therefore, the valve manufacturer may propose alternative materials (equivalent or better), conditioned to
PETROBRAS approval.
A.8.3.2. For a material to be accepted as equivalent or better, it shall have the same or better mechanical (i.e. yield
strength, hardness, etc.) and anti-corrosive properties (measured by PREN), be suitable for temperature range
presented in the VDS whilst not being susceptible to phenomenon such as brittle fracture or stress corrosion cracking.
A.8.3.3. Charpy impact testing is required for all materials, considering minimum temperature listed in ASME B31.3,
section 323 or as listed in the VDS, whichever is lower. All metallic materials shall be suitable for minimum temperature
service of -29°C.
A.8.3.4. Some examples of alternative materials are:
A.8.3.4.1. For pressure-containing parts, forging materials are acceptable in place of casting materials, but not vice-
versa.
A.8.3.4.2. For remaining internal parts (i.e.: non pressure-containing), forgings and castings are interchangeable as
long as they have the same desired properties (i.e.: mechanical properties, corrosion resistance, maximum or minimum
hardness, and other properties as applicable).
A.8.3.4.3. Superduplex (UNS S32760) may be used as replacement for duplex (UNS S31803), but not vice-versa.
A.8.3.4.4. Superduplex and duplex steels shall not be used for chlorinated seawater services (SW).
A.8.3.4.5. Nickel Aluminum Bronze (UNS C95800) may be used as replacement for bronze B62 (UNS C83600), but
not vice-versa.
A.8.3.4.6. Higher mechanical strength alloys such as ASTM A694 F60 or ASTM A694 F65 (see A.6.1.3.3.) are
acceptable instead of ASTM A105 or ASTM A216 Gr WCB. For Nickel-based alloy cladded valves used for sour service,
the base material shall be NACE compliant.
A.8.3.4.7. Superduplex and duplex steels may be replaced by carbon steel with 3 mm of Alloy 625 overlay, and vice-
versa if low temperature requirements are satisfied. Additionally, the pressure-temperature rating shall be validated.
A.8.3.4.8. Austenitic steels with PREN number less than that of 316/316L shall not be used on offshore facilities (e.g.:
AISI 304 and AISI 304L stainless steel materials shall not be used).
A.8.3.4.9. Internal parts made of martensitic stainless steels (e.g.: AISI 410) may be replaced by higher chromium alloys
such as ASTM A564 Gr 630 H1150 (17-4PH), superduplex or duplex steels.
A.8.3.4.10. ASTM A350 LF3 may be replaced with ASTM A350 LF2 CL1, in case minimum temperature is above - 46°C.
A.8.3.4.11. Internal parts made of austenitic stainless steels may be replaced with higher chromium alloys, if low
temperature requirements are satisfied:
- Down to - 46°C: ASTM A350 LF2 CL1 with 3 mm of Alloy 625 overlay or ASTM A564 Gr 630 H1150 (17-4PH);
- Down to - 51°C: Duplex (UNS S31803) or Superduplex (UNS S32760);
- Down to - 100°C: ASTM A350 LF3 with 3 mm of Alloy 625 overlay, ASTM A522 type I with 3 mm of alloy 625
overlay or full inconel parts.
A.8.3.4.12. Low temperature carbon steel parts (i.e.: ASTM A350 LF2, ASTM A350 LF3) may be used in lieu of regular
carbon steel parts (e.g.: ASTM A105, ASTM A216 WCB).
- Rev. 13 - Page 64 of 84
DISCIPLINE: PIPING
A.9. INSPECTION & TESTING

A.9.1. INSPECTION REQUIREMENTS
A.9.1.1. INSPECTION AND TESTING PLAN (ITP)
A.9.1.1.1. The ITP shall be issued by the supplier and submitted to PETROBRAS or EPC contractor approval.
A.9.1.1.2. The ITP shall allow the identification of stages, through the valve production cycle, where it shall be done
checks or inspections, including those carried out by material or service suppliers.
A.9.1.1.3. The ITP shall indicate the types of examinations, tests or checks to be made, as well as procedures and/or
applicable instructions, acceptance criteria and issued records.
A.9.1.1.4. The ITP shall contain register of critical quotas as defined by the manufacturer, including, at least,
standardized quotas in the construction and design standards of valves.
A.9.1.1.5. The ITP shall contain the procedures and instructions for inspection of all expected activities.
A.9.1.1.6. The inspection shall be performed by PETROBRAS or EPC contractor.
A.9.1.2. RECEIVING INSPECTION
A.9.1.2.1. The receiving inspection shall be performed without causing damages to the package and without
compromising the preservation of the valves.
A.9.1.2.2. It shall be checked the valve and its components as the Data Book, identification (e.g. valve serial number,
actuator serial number, pressure class, etc.) and manufacturer manual for handling, storage and preservation.
A.9.1.2.3. After verifying the documentation and attesting its conformity, the packed shall be stored according to item
A.10.
A.9.1.3. NON DESTRUCTIVE TESTING (NDT)
The execution of NDT shall follow specific requirements, according to type of material:
A.9.1.3.1. CAST IRON AND BRASS VALVES:

- 100% visual inspection;
- for body and bonnet made of cast iron or forgings, pressure class 150 and 300, magnetic particle testing is
required at least in 20% of each batch material.
A.9.1.3.2. CARBON STEEL VALVES:

- for body and bonnet made of forgings, pressure class 600, 900, 1500, 2500 and 10.000psi, magnetic particle
testing is required in 100% of each batch material;
- for body and bonnet made of casting, pressure class 600, 900, 1500, 2500 and 10.000psi, radiographic
examination in critical areas is required in 100% of each batch material.
A.9.1.3.3. CARBON ALLOY STEEL VALVES:
a) ASTM A522 Type I (forging):

- for body and bonnet made of forgings, pressure class 150 and 300, liquid penetrant inspection is required at
least in 20% of each batch material;
- Rev. 13 - Page 65 of 84
DISCIPLINE: PIPING
- for body and bonnet made of forging, pressure class 900, 1500, 2500 and 10.000psi, liquid penetrant inspection
is required in 100% of each batch material;
- for body and bonnet made of castings, pressure class 900, 1500, 2500 and 10.000psi, radiographic examination
is required in 100% in critical areas.
Table A.58 – Chemical composition for ASTM A522 – Type I
Chemical Carbon
Manganese Phosphorus Sulfur Silicon Nickel
Composition (max.)
ASTM A522 Type I 0,06 0,59 < 0,005 < 0,001 0,28 9,08
A.9.1.3.4. STAINLESS STEEL VALVES:

- for body and bonnet made of forgings, pressure class 900, 1500, 2500 and 10.000psi, liquid penetrant inspection
is required in 100% of each batch material;
- for body and bonnet made of casting, pressure class 900, 1500, 2500 and 10.000psi, radiographic examination
is required in 100% in critical areas.
A.9.1.3.5. STAINLESS STEEL DUPLEX AND SUPER DUPLEX VALVES:

- for body and bonnet made of forgings, pressure class 900, 1500, 2500 and above, liquid penetrant inspection is
required in 100% of each batch material;
- for body and bonnet made of casting, pressure class 900, 1500, 2500 and above, radiographic examination is
required in 100% in critical areas.
A.9.1.3.6. Additional Requirements:

- all valves specified for hydrogen sulfide service shall be in strict accordance with the requirements of the ISO
15156;
- visual inspection shall be according to ASME BPV section V. The acceptance criteria shall be according to MSS
SP-55 specification;
- liquid penetrant and magnetic particles testing shall be according to ASME BPV section V. The acceptance
criteria shall be according to ASME B16.34 specification for class pressure up to 600#. For higher class
pressures the acceptance criteria shall be according to ASME B16.4, with the exception that no linear indication
shall be accepted;
- visual inspection shall be according to ASME BPV section V. The acceptance criteria shall be according to
ASME B16.34 specification;
- radiographic examination shall be according to ASME BPV section V and ASTM E94. The acceptance criteria
shall be according to ASME B16.34 specification;
- Rev. 13 - Page 66 of 84
DISCIPLINE: PIPING
- for castings valves NDT examinations shall focus on critical areas.
A.9.2. DESIGN VALIDATION
A.9.2.1. The design validation of a valve is requested according its VSL classification, as presented as follows:
Table A.59 – Design validation requirements according VSL classification
VSL Classification VSL-1 VSL-2 VSL-3 VSL-4
Design Validation No Design analytical approval Design validation test approval (PVT)
A.9.2.2. For VSL-1 valves, no design validation is required. In this case, the manufacturer shall perform the design and
manufacture the valve attending all requirements listed in the applicable standards (e.g.: API 6D, API 6A, etc.).
A.9.2.3. For VSL-2 valves, design validation is required at documentation level. In this case, the manufacturer shall have
an analytical approval of the valve design. To attend this kind of design validation, the manufacturer shall submit for
PETROBRAS approval:
- Certificate of approval, issued by a 3rd party, referred to an analytical approval of the valve design, according
normative requirements (e.g.: NBR 15827, API 6D, API 6A, API 600, API 609, etc.); or
- A valid API monogram of the valve design, complying to all normative requirements of quality and design.
NOTE: In case the manufacturer has already performed a PVT test in the past on a representative prototype of the valve
design or on a valve which scaling may be considered valid, the requirement of design analytical approval may be
demonstrated by the certificate of approval. This certificate, referred to the execution to this PVT test, shall be issued by
a 3rd party.
A.9.2.4. For VSL-3 and VSL-4 valves, design validation is required at PVT test execution level. In this case, the
manufacturer shall perform all PVT tests on a representative prototype of the valve that will be supplied.
NOTE: The manufacturer is free of charge on performing the PVT test, in case it is presented a certificate of approval,
issued by 3rd party, referred on a PVT test performed in the past, on a representative prototype of the valve that will be
supplied or on a valve which scaling may be considered valid.
A.9.2.5. In the case of PVT test execution, the following Standards may be considered to the test:
- NBR 15827; or
- API 6A, considering PSL 3G, PR2 (Appendix F); or
- API 6AV1.
NOTE: In case of missing technical requirements, including acceptance criteria (e.g.: ball valve on API 6A), the PVT test
procedure shall be elaborated from better suited standards such as NBR 15827, and submitted to PETROBRAS
approval.
A.9.2.6. For a supply of a fire tested valve, the manufacturer shall also present a certificate of approval, issued by 3rd
- Rev. 13 - Page 67 of 84
DISCIPLINE: PIPING
party, complying to ISO 10497.

A.9.2.7. For a supply of a fugitive emissions valve, the manufacturer shall also present a certificate of approval, issued
by 3rd party, complying to ISO 15848.
A.9.3. FACTORY ACCEPTANCE TEST (FAT) REQUIREMENTS

A.9.3.1. TEST MEDIUM
A.9.3.1.1. The manufacturer shall consider the use of the following test medium:
For all tests with liquid: It shall be used fresh water with an addition of corrosion inhibitor.
NOTE: The chloride content of test water in contact with austenitic and duplex stainless steel wetted components of
valves shall not exceed 30 μg/g (30 ppm by mass) and the water temperature shall not be greater than 38°C (100°F)
during the testing period.
For high pressure gas tests: It shall be used dry nitrogen (N2).
For low pressure gast tests: It may be used dry air or nitrogen (N2).
A.9.3.2. TEST BENCH
A.9.3.2.1. The manufacturer shall attend all requirements herein stated for the design and assembly of the test bench
dedicated to perform the FAT tests of the valve / actuator.
A.9.3.2.2. It shall be considered, as minimum, the use of the following equipment:
a) Test Panel with devices for manual and automatic operation, provided of pressure transmitters, digital indicators
or controllers, pressure meters, solenoid valves, relays, end-of-stroke indicators, cycles counter, etc., as well as
hydraulic systems (hydraulic units, etc.) compatible with the flows and test pressure levels for the valve / actuator
which will be tested.
b) Fittings and tubing of stainless steel.
c) High pressure hoses.
d) Torque tool.
e) Data acquisition system, with capacity to adequately record the values of pressure and / or torque during test
execution.
A.9.3.2.3. The manufacturer shall take attention to the adequacy of protection for personnel carrying out the testing, in
the event of failure of a valve, connection or equipment during the test. Additional caution shall be taken whenever high
pressure gas tests are required.
A.9.3.3. MONITORING PORTS FOR ACTUATED VALVES
A.9.3.3.1. During execution of any valve cycle, the following pressure ports shall be monitored / registered:
a) Valve upstream pressure
b) Valve downstream pressure
c) Valve body pressure
- Rev. 13 - Page 68 of 84
DISCIPLINE: PIPING
d) Actuator input (e.g.: hydraulic or pneumatic pressure, electric current)
e) Valve stroke
A.9.3.4. LEAKAGE IDENTIFICATION
A.9.3.4.1. The test bench shall have the capacity to monitor eventual leakages and allow to measure the volume in
order to allow verification of the acceptance criteria.
A.9.3.4.2. Hydraulic lines must be, whenever technically possible, built with short stainless steel tubing, to increase the
sensitivity to leakage detection. With the same purpose a procedure for purging the air of the valve body, the actuator
and the test panel must be foreseen. This procedure shall be approved by PETROBRAS.
A.9.3.4.3. During sealing tests with liquid, whenever visual observation of leakage in a direct way is not possible,
leakages can be monitored by pressure variation.
A.9.3.4.4. In case of leakage identification by pressure variation, one example of a method of quantifying sensitivity of
the test bench would be the creation of a “leakage”, small and controlled, where the leaked volume variation would be
co-related with the pressure drop generated by this “leakage”, for each test condition (pressure value, upstream lines,
downstream, ambient temperature, etc.).
A.9.3.4.5. Detection of a leakage shall be associated with the identification of a continuous pressure variation, without
occurring its stabilization along the time and since the effects of temperature variation can be disregarded (or
compensated). Thus, the pressure drop in an upstream line or pressure rise in a downstream line , without stabilization
of these pressure variations shall be considered as leakage.
A.9.3.4.6. In case of leakage identification by using level variation in a capillary, its diameter shall be compatible with
the capacity of identifying small leakages / volumes.
A.9.3.4.7. Pneumatic shell test shall be performed using inert gas, such as mixture of 99 % nitrogen with a 1 % helium,
tracer measured using a mass spectrometer, in order to guarantee leakage detection. Alternatively, if nitrogen (100%)
is used as test medium, the valve shall be submerged.
A.9.3.4.8. In case of monitoring gas leakage at the pressure ports, for higher and constant leakages it shall be
considered the use of flowmeters operating inside 20% to 80% of the nominal capacity of it.
A.9.3.4.9. For monitoring gas leakage on pressure ports for smaller or inconstant leakages it shall be performed by
using scale burette where a flexible hose is inserted totally on a burette (or at least above the meniscus) and the set is
submerged on a transparent aquarium filled with clean water. Monitoring of leakage shall be done by registering the
displacement of the meniscus line inside the burette, which can be seen through the aquarium.
A.9.3.4.10. Before each type of test, the manufacturer shall present the test bench set-up in order to demonstrate that it
is assembled on a correct way to perform the tests and monitor eventual leakages. The following items shall be
concerned during this presentation:
a) It shall be verified that the pressure source is connected to the correct pressure port.
b) It shall be verified that all test devices are properly assembled, such as if flanges and fittings are tightened,
check of instrumentation valves position (fully opened or fully closed), identification of hoses (which shall be in
a good shape, without creases, holes or tears), etc.;
c) Before gas tests, if the valve is completely purged.
- Rev. 13 - Page 69 of 84
DISCIPLINE: PIPING
d) Check of safety rules appliance, prior to beginning the tests.
A.9.3.5. FAT SEQUENCE
A.9.3.5.1. All manual and actuated valves shall be subjected to a Factory Acceptance Test (FAT) prior to delivery and/or
shipping the valve.
A.9.3.5.2. It shall be considered the execution of FAT for the valve and its actuator.
A.9.3.5.3. Otherwise agreed, the FAT shall be performed with the actuator assembled onto the valve.
A.9.3.5.4. A functional test of valve + actuator shall be considered in order to guarantee adequate performance of the
set.
A.9.3.5.5. Valves wich design contains fugitive emissions requirement shall also perform additional FAT tests according
to item A.9.3.6.
A.9.3.5.6. HIPPS valves shall also perform additional FAT tests according to item A.9.3.7.
A.9.3.5.7. Any conflict between contract requirements and this document shall be presented for PETROBRAS
evaluation.
A.9.3.5.8. The FAT of bronze globe valves shall follow MS SP-80. The FAT of other globe valves shall follow BS 1873
/ BS 12266 or API 623 requirements, as applicable, and applicable tests listed in these Standards shall be performed.
A.9.3.5.9. The FAT of butterfly valves (except to the triple offset design) shall follow API 609 / API 598 requirements,
and applicable tests listed in these Standards shall be performed, including the optional high-pressure closure test.
A.9.3.5.10. The FAT of ball, gate, check, plug, axial and triple offset butterlfy valves shall be as bellow. The FAT of ball
and gate valves complying with IOGP S-562 and S-611 shall be according to A.7.1.8 and A.7.2.5, repectivelly.
Pressure tests according the respective QSL requirement for each VSL classification:
Table A.60 – QSL / PSL requirement according VSL classification
VSL-2 (not for VSL-2 (with

VSL Requirements VSL-1 VSL-3 VSL-4
hydrocarbon) hydrocarbon)
QSL
QSL-2 QSL-2 QSL-3 QSL-3 QSL-4
(According API 6D)
PSL PSL-3 or PSL-3G PSL-3 or PSL-3G as

NA PSL-4 PSL-4
(According API 6A) as applicable applicable
a) For VSL-1 valves, it shall be performed pressure tests according to API 6D QSL-2 requirements.
b) For VSL-2 valves, it shall be performed pressure tests according to API 6D QSL-3 requirements. For liquid
service application, it shall be performed pressure tests according to API 6D QSL-2 requirements.
c) For VSL-3 valves, it shall be performed pressure tests according to API 6D QSL-3 requirements.
d) For VSL-4 valves, it shall be performed pressure tests according to API 6D QSL-4 requirements.
In addition to the pressure tests required by Table A.60, the FAT of ball valves shall consider the
execution of the following supplementary tests listed in Annex H of API 6D: H.5, H.6, H.7, H.8, H.9, H.11.
NOTE: Otherwise agreed, the supplementary tests H.9 and H.11 shall be performed using gas as test medium.
The acceptable leakage rate for the tests shall be according to API 6D, except to:
- Rev. 13 - Page 70 of 84
DISCIPLINE: PIPING
a) Hydrostatic seat test and low-pressure gas seat test of metal seated valves: the acceptable leakage shall be
ISO 5208 Rate B. For DBB tests the acceptable leakage is 2 X B.
b) High-pressure gas seat test of metal seated valves: the acceptable leakage rate shall be 2 X C (two times ISO
5208 Rate C). For DBB tests the acceptable leakage is 4 X C.
NOTE: Whenever DBB feature is required for the valve design at closed or closed & opened position, it shall be
considered the execution of DBB test on both conditions.
c) Triple offset butterlfy valves: The acceptable leakage rate for all HP/LP sealing (i.e.: seat) tests shall be ISO
5208 Rate A.
Prior to perform the drive train strength test, listed in item H.7 of API 6D, the manufacturer shall provide
the following information:
a) Drive train engineering data (i.e.: stem calculation), demonstrating that the design thrust or torque for all drive
train calculations is at least two times the breakaway thrust or torque of the valve (i.e.: maximum thrust or torque
required to operate a valve at maximum pressure differential).
b) Actuator engineering data (e.g.: gearbox, hydraulic, etc.), demonstrating that proper safety factor has been taken
into account.
c) Test fixture design data, in order to guarantee that the test fixture used to block the obturator is able to withstand
the loads of the test and it would not damage the surface of the parts in contact (i.e.: ball / seats edges, sealing
region).
d) The selected torque value (acc. item H.7 of API 6D) that will be applied on the drive train strength test. If the
valve actuator (e.g.: gearbox, hydraulic, etc.) is used to generate the torque test, it shall be checked the values
of maximum output torque of the actuator and the selected torque value for the test, in order to confirm its
compatibility.
NOTE: The drive train strength test shall be performed prior to the sealing tests (i.e.: seat test) and it may be done in
only one valve of the lot, per nominal, per actuator type (e.g.: gearbox, hydraulic, etc.), and per pressure class,
conditioned to:
- Agreement by test inspector of all documentation listed in this item.

- No failures on the drive train strength tests. If one valve of the lot failures on the drive train strength, the others
valves with same design premise shall perform the test.
A.9.3.6. FUGITIVE EMISSIONS FAT
A.9.3.6.1. Whenever specified in the VDS that the valve shall be fugitive emissions approved, a minimum of one valve
of the lot shall be selected at random from each production lot of valves per valve type, pressure class and nominal size,
and tested according to ISO 15848 Part 2.
A.9.3.6.2. The manufacturer shall prepare specific Factory Acceptance Test (FAT) procedure, according to ISO 15848
Part 2, and submit for PETROBRAS approval.
A.9.3.6.3. The “Tightness Class” shall be according:
Table A.61 – Tightness class for stem seals - fugitive emissions (ref.: ISO 15848 Part 1)
- Rev. 13 - Page 71 of 84
DISCIPLINE: PIPING
Tightness Class
Measured Leak Rate 1
(Stem seals)
A ≤ 50
B ≤ 100
C ≤ 1000
1
ISO 15848 Part 1 - Annex B (1 ppmv = 1 ml/m3 = 1 cm3/m3)
Table A.62 – Tightness class for body seals - fugitive emissions (ref.: ISO 15848 Part 1)
Measured concentration
≤ 50 1
(Body seals)
1
ISO 15848 Part 1 - Annex B (1 ppmv = 1 ml/m3 = 1 cm3/m3)
A.9.3.6.4. The FAT report shall be according to item 7 of ISO 15848 Part 1.
A.9.3.6.5. Valves shall comply with stem tightness class BH.
A.9.3.7. HIPPS VALVE IN PLACE TEST
A.9.3.7.1. All HIPPS valves shall be able to pass through a regular testing to demonstrate correct function and
monitoring operating status. The test interval shall be consistent with the basis of the SIL analysis.
A.9.3.7.2. Following are the minimum considerations that shall be verified during in place test of a HIPPS valve:
a) Regular Pressure/Leak Integrity Testing: The HIPPS shall be capable of demonstrating that the system has
sufficient integrity to contain SIP with leakage less than the maximum leak rate. Testing interval will be
determined by SIL rating or regulatory requirement.
b) Maximum Leak Rate Testing: The HIPPS design shall include appropriate methods to measure or infer the leak
rate of the HIPPS for comparison to the predetermined maximum leak rate. Maximum leak rate determination
shall consider both short-term shutdown events and long-term shutdown events such as a storm shut-in and
shall either be set by the operator or by regulatory requirement.
c) Partial Stroke Testing (PST): Each valve shall be supplied with a dedicated Partial Stroke Test (PST) system
installed inside the local control valve cabinet. Required Partial Stroke Test shall be implemented using devices
specifically designed and certified for that purpose. PST shall be considered as a functional test which covers
only a fraction of the possible failures, and not as self-test with diagnostic coverage. The fraction detected shall
be properly documented. As minimum, the following tests shall be scope of the PST:
- 4 actuations of HIPPS valves under operational condition, with nominal line pressure in upstream, downstream
and body cavity;
- 4 actuations of HIPPS valves under DBB condition, direction open to close. In this case the valve should be at
opened position, with nominal line pressure in the bore and without pressure in the cavity;
- Rev. 13 - Page 72 of 84
DISCIPLINE: PIPING
- 4 actuations of HIPPS valves under DBB condition, direction close to open. In this case the valve should be at
closed position, with nominal line pressure in upstream and downstream, and without pressure in the cavity;
- For the FAT tests of the valve HIPPS, the sequence described herein shall be done considering the line pressure
of 0% PMT, 50% PMT and 100% PMT.
NOTE: The results of the PST shall be registered using a statistical analysis (i.e.: average, standard deviation), in order
to serve as a reference for the commissioning test and periodical test. Also, a failure mode effects and criticality analysis
(e.g.: FMECA) shall be considered to be used.
A.10. HANDLING, STORING & SHIPPING

A.10.1. The manufacturer shall present a tested/validated procedure by laboratory performance for the preservation
system and a procedure with handling, storing, packaging and shipping the valve (including actuator and positioner -
electric/electronic parts).
A.10.2. After hydrostatic test, all valves shall be purged with dry compressed air, in the fully open position, until they are
completely dry.
A.10.3. After purge, the valve shall be kept closed or opened, according to manufacturer instruction, inner protected
with VCI for all the parts and no corrosion protector that will need any solvent to be removed may be used.
A.10.4. Valves with corrosion resistant materials needs the corrosion inhibitor for liquid and vapor phase added on the
water, but do not need the use of VCI. Corrosion protector that will need any solvent to be removed shall not be used.
A.10.5. Valves made of brass, stainless steel and other non-oxidizable metal alloys shall receive protection against dust
and moisture.
A.10.6. Small sized valves may be shipped inside a collective package. Even that, each valve shall be individually
package prior to assembly the collective package.
A.10.7. Medium valves shall have an individual package.
A.10.8. Large valves shall be packed limited to their nozzles considering that they are protected by the painting.
A.10.9. The valves may be packed on upright or horizontal position, on open or closed position, according to
manufacturer recommendation.
A.11. DOCUMENTATION
A.11.1. DOCUMENTATION FORMATS & QUALITY
A.11.1.1. Whenever is possible (e.g.: a supply from a Brazilian manufacturer) all documentation shall be delivered in
Portuguese (pt-BR). An alternative language to be considered for the documentation shall be English (e.g.: supply from
an international manufacturer). Any deviation shall be requested and approved by PETROBRAS in advance of the
delivery.
A.11.1.2. Typically, the format for the documents shall be Adobe Acrobat PDF (*.PDF). Other formats shall be agreed
with PETROBRAS.
A.11.1.3. All documentation shall be of good quality with maximum legibility. Scanned images shall be checked before
submittal for proper image quality, skewness and completeness.
- Rev. 13 - Page 73 of 84
DISCIPLINE: PIPING
A.11.2. DATA BOOK
A.11.2.1. The Data Book shall be filled in a manner which will facilitate rapid retrieval of information. They shall be made
available to PETROBRAS, if required, for at least 5 years following the commencement of the guarantee period of last
batch commercialized.
A.11.2.2. The Data Book shall represent the manufacturer's compilation of calculations together with the necessary
drawings, manufacturing, testing and inspection procedures, certificates, personnel qualifications, non-conformance
reports, records and reports required to demonstrate that the valve and actuator is in compliance with PETROBRAS’s
requirements.
A.11.2.3. It shall include, as minimum:
a) Material certificates of compliance;
b) ITP copy approved by PETROBRAS or EPC purchaser;
c) Copy of all reports issued by the company responsible for inspection;
d) WPS and WPQR for structural welding;
e) Repair weld maps;
f) NDT reports with lists of welder and NDT operator qualifications and procedures, and drawings of critical areas
for NDT;
g) Relevant fabrication drawings;
h) Reports of non-compliance and corrective actions taken;
i) FAT procedure and test results.
j) Actuator certificate;
k) Positioner certificate;
l) Fire-test certificate, when applicable;
m) Fugitive emission certificate, when applicable;
n) Inspection final report for shipment.
A.11.2.4. The issue of certificates shall be according EN 10204 type 2.2 for parts with no risk for environment as: hard
welding deposit, closures, seal, springs and so on.
A.11.2.5. The issue of certificates shall be according EN 10204 type 3.1 for parts with risk for environment as: body,
bonnet, cover, stem, studs/bolts, etc.
A.11.2.6. The Data Book shall be issued one per valve or one per purchase order (with traceability for valves groups).
One hard copy of the Data Book shall be sent with the valve to final destination and an electronic copy shall be sent to
the PURCHASER.
A.11.2.7. All material certificates shall be identified with: valve serial number, project name (when applicable), purchase
order number, order item number, VDS number or project number.
- Rev. 13 - Page 74 of 84
DISCIPLINE: PIPING
A.11.3. USER MANUAL
A.11.3.1. The User Manual shall in an organized manner, give sufficient information in order to enable operation and
maintenance of the valve in a safe, economical and functionally correct manner during all phases after installation.
A.11.3.2. The User Manual shall cover valve and actuator.
A.11.3.3. All documents shall be updated to "as-built".
A.11.4. DOCUMENTATION OF PRESERVATION, PROTECTION AND PACKING
A.11.4.1. The manufacturer shall prepare and submit procedure(s) for PETROBRAS approval, showing the following:
a) description of the initial preservation/protection/packing carried out by the manufacturer prior to shipment:
- The procedure shall also specify type of preservatives/ lubricants used, with technical data, handling and safety
instructions, especially giving details of any chemical substances used that may be hazardous to personnel or
environment.
b) description of re-preservation after incoming inspection at end destination:
- Preservation maintenance is to be carried out by the user during storage, installation and in the period prior to
start-up for the intended use.
c) unpacking and removal of protective devices and preservatives prior to operation:
- The procedure shall indicate the proposed lifting methods for the valve and actuator, and all additional measures
that shall be observed prior to and during installation.
A.11.4.2. The documentation of preservation, protection and packing shall fulfill all requirements stated on item A.10.
A.11.5. VALVE CODE

A.11.5.1. DESCRIPTION
A.11.5.1.1. All valves specified for application in Exploration and Production (E&P) oil production and process facilities
have a unique code, in order to have uniformity and to systematize the coding of valves so that they can be handled in
an organized manner and information can be easily retrieved.
A.11.5.1.2. The complete structure of all valve codes shall be as follows:
A.11.5.2. BASIC STRUCTURE OF A VALVE CODE
A.11.5.2.1. The valve code shall be made up of 3 basic groups ordered as follows:
- Rev. 13 - Page 75 of 84
DISCIPLINE: PIPING
Group 0 Group 1 Group 2
Valve Type Pressure Rating VSL

LLL - A - B
Where:
L is a letter;
A, B are numbers.
A.11.5.3. CONCECPT OF BASIC GROUPS
A.11.5.3.1. IDENTIFICATION OF VALVE TYPE (GROUP 0)
This is the basic group that identifies the type of the valve.
This group is comprised of three letters and its configuration is illustrated as follows:
Group 0
Valve Type
LLL
The following characters shall be used to distinguish the type of the valve:
VAG – Needle valve
VAX – Axial valve
VBO – Butterfly valve
VDE – Double Ball valve
VDI – Diaphragm valve
VES – Ball valve
VGA – Gate valve
VGL – Globe valve
VMA – Plug valve
VRE – Check valve
A.11.5.3.2. IDENTIFICATION OF PRESSURE RATING (GROUP 1)
This is the basic group that identifies the pressure rating of the valve.
This group is comprised at least of three and maximum of 5 numbers and its configuration is illustrated
as follows:
Group 1
Pressure Rating
The following characters shall be used to distinguish the pressure rating of the valve:
- Rev. 13 - Page 76 of 84
DISCIPLINE: PIPING
125 – ASME Class 125
250 – Maximum pressure 250 psi (for Category A butterfly valves only)
800 - ASME Class 800
801 – ASME Class 800 with SCH 40S (for ball valves)
801 – ASME Class 800 with SW ends ASME B16.11 (for gate valves)
802 – ASME Class 800 with SCH 80
804 – ASME Class 800 with SCH XXS
1501 – ASME Class 1500 with SCH 40S (for ball vales)
2500 – ASME Class 2500, with ASME flanges
2501 – ASME Class 2500 with SCH 40S (for ball valves)
2510 – ASME Class 2500, with compact flanges
3000 – Maximum Pressure 3.000 psi
A.11.5.3.3. IDENTIFICATION OF VSL (GROUP 2)
This is the basic group that identifies the VSL of the valve.
This group is comprised with one number and its configuration is illustrated as follows:
- Rev. 13 - Page 77 of 84
DISCIPLINE: PIPING
Group 2
VSL
The following characters shall be used to distinguish the VSL of the valve:
1 – VSL-1
2 – VSL-2
3 – VSL-3
4 – VSL-4
A.11.5.4. SPECIFIC STRUCTURE OF A VALVE CODE
A.11.5.4.1. The valve code shall be made up of 4 specific groups ordered as follows:
Group 3 Group 4 Group 5 Group 6
Material Class Body material Obturator type TRIM design

L - C - D - E
Where:
L is a letter;
C, D, E may be either numbers or letters.
A.11.5.5. CONCECPT OF SPECIFIC GROUPS
A.11.5.5.1. IDENTIFICATION OF MATERIAL CLASS (GROUP 3)
This is the basic group that identifies the material class of the valve.
This group is comprised of one letter and its configuration is illustrated as follows:
Group 3
Material Class
L
The following characters shall be used to distinguish the material class of the valve:
C – Carbon steel
A – Alloy Steel
S – Stainless steel
D – Duplex steel
N – Nickel alloy
U – Uncommon materials
A.11.5.5.2. IDENTIFICATION OF BODY MATERIAL (GROUP 4)
- Rev. 13 - Page 78 of 84
DISCIPLINE: PIPING
This is the basic group that identifies the body material of the valve.
This group is comprised of one number and its configuration is illustrated as follows:
Group 4
Body Material
C
The following characters shall be used to distinguish the body material of the valve, related to the specific
material class of the valve:
- Rev. 13 - Page 79 of 84
DISCIPLINE: PIPING
Table A.63 – Identification of body material code, according to respective material class
Material Class
Body C A S D N U
Material
Stainless Nickel Uncommon
Carbon steel Alloy steel Duplex steel
steel alloys materials
ASTM A105 ASTM A350 LF3 Alloy 625
1 or or - ASTM A995 Gr. 1B (UNS Bronze
ASTM A216 WCB ASTM 352 LC3 N06625)
ASTM A182
ASTM A182 Gr.
A350 LF2 CL1 Gr. F316
F51
2 or ASTM A182 F5 or
or
- ASTM A536-65-45-12
ASTM A352 LCC ASTM A351
ASTM A995 Gr. 4A
Gr. CF8M
ASTM A105
or ASTM A182
Gr. F317 ASTM A182 Gr.
ASTM A216 WCB ASTM A182 F11 ASTM B148
3 + CL2
or F55 or -
(UNS C95800)
ASTM A351 ASTM A995 Gr 6A
Organic Coating Gr. CG8M
(Onshore use only)
ASTM A105
or ASTM A182
Gr. F347
ASTM A216 WCB
4 +
ASTM A522 Type I or - - Plastics
ASTM A351
Organic Coating Gr. CF8C
(Offshore)
or or
ASTM A216 WCB ASTM A352 LC3
5 + +
- - - Gray Iron
alloy 625 overlay alloy 625 overlay

(UNS N06625) (UNS N06625)
ASTM A350 LF2
CL1
ASTM A522 Type I
or
+
6 ASTM A352 LCC
alloy 625 overlay
- - - -
+
(UNS N06625)
alloy 625 overlay
(UNS N06625)
A.11.5.5.3. IDENTIFICATION OF OBTURATOR TYPE (GROUP 5)
This is the basic group that identifies the obturator type of the valve.
Group 5
Obturator Type
D
The following characters shall be used to distinguish the obturator type of the valve:
- Rev. 13 - Page 80 of 84
DISCIPLINE: PIPING
Table A.64 – Identification of obturator type, according to valve type
Valve Type
Obturator
type Butterfly
Gate valve Globe valve Check Valve
valve
Solid
0 Bevelled disc Piston
wedge
1 Slab gate Angular Dual Plate
2 Expanding - Swing
Flexible
3 - Axial non-slam
wedge See Table
4 - - Ball A.50
Swing, spring loaded,
5 - -
non-slam
6 - - Manufacturer standard
Bevelled disc, with
F - -
fugitive emission
NOTE: For ball and double ball valves, the last two digits “D” (GROUP 5) and “E” (GROUP 6) in the valve code presents
the configuration number of the valve, where:
DE – presents the basic configuration, according Table A.25 – for metallic ball valves up to NPS 1 1/2 (“Forged” valves);
DE – presents the basic configuration, according Table A.28 – for metallic double ball valves up to NPS 2 (“Forged”
valves);
DE – presents the basic configuration, according Table A.52 – for non-metallic valves;
D - presents the selected group seal, according Table A.23 – for ball valves with NPS 2 and above and for double ball
valves with NPS 3 and above.
A.11.5.5.4. IDENTIFICATION OF TRIM DESIGN (GROUP 6)
This is the basic group that identifies the TRIM design of the valve.
Group 6
TRIM Design
E
The following characters shall be used to distinguish the TRIM design of the valve:
- Rev. 13 - Page 81 of 84
DISCIPLINE: PIPING
Table A.65 – Identification of TRIM design, according to valve type
Valve Type
TRIM Valve Type
design Gate
Check Butterfly (see Table A.51)
Globe
Double Flanged
Standard Soft Face type Lug
1 (Short Pattern)
TRIM TRIM
Alternative Metal to Metal RF 1 3
2
TRIM TRIM
FF 4 6
Alternative
3 N/A Metal to Metal RTJ 7 9
TRIM
NOTE: For ball valves, the last two digits “D” and “E” in the valve code presents the configuration number of the valve,
where:
DE – presents the basic configuration, according Table A.25 – for metallic ball valves up to NPS 1 1/2 (“Forged” valves).
DE – presents the basic configuration, according Table A.28 – for metallic double ball valves up to NPS 2 (“Forged”
valves);
DE – presents the basic configuration, according Table A.52 – for non-metallic valves;
E - presents the basic configuration, according Table A.26 – for ball valves with NPS 2 and above and for double ball
valves with NPS 3 and above.
A.11.5.5.5. EXAMPLE OF VALVE CODE
Example 1
Gate valve, pressure rating class 900, VSL-2, material class of carbon steel, solid wedge, using standard TRIM:
VGA-900-2-C101
Valve Type: VGA – Gate valve
Pressure Rating: 900 – Class 900
VSL: 2 – VSL-2
Material Class: C – Carbon steel
Body Material: 1 – ASTM A105 or ASTM A216 WCB
Obturator type: 0 – Solid wedge
Trim design: 1 – Standard TRIM
Example 2
Ball valve, pressure rating 1500, VSL-2, material class of carbon steel, configuration 04 with nipple SCH XXS:
VES-1504-2-C207
Valve Type: VES – Ball valve
Pressure Rating: 1504 – ASME Class 1500 with SCH XXS
VSL: 2 – VSL-2
Material Class: C – Carbon steel
- Rev. 13 - Page 82 of 84
DISCIPLINE: PIPING
Body Material: 2 – A350 LF2 CL1 or ASTM A352 LCC

Configuration: 07 – Metal-to-metal ball valve with configuration according Table A.25
Example 3
Ball valve, pressure rating 2500, VSL-3, material class of super duplex, soft sealing, fire tested, DIB-2:
VES-2500-3-D339
Valve Type: VES – Ball valve
Pressure Rating: 2500 – ASME Class 2500
VSL: 3 – VSL-3
Material Class: D – Super duplex
Body Material: 3 – ASTM 182 Gr. F55
Seal Group: 3 – Groups D or E
Configuration: 9 – Soft sealing ball valve with configuration according Table A.26.
- Rev. 13 - Page 83 of 84
DISCIPLINE: PIPING
A.12. VALVE DATASHEET - VDS
- Rev. 13 - Page 84 of 84
N/A
N/A
N/A
A.12.1 BALL VALVES
Valve Code VES-10000-2-D334
Specs J12P J12
1. Valve Type Ball
2. Sealing Type Soft
3. Valve Specification Level (VSL) VSL-2
4. Ball Mouting Trunnion
5. Standard API 6A
6. Size Range (NPS) 1" - 2"
7. End Connection API 6A, 6BX
8. Pressure Class max. press 10000 psi
9. Temperature -50°C to 150°C
10. Material Class Super Duplex Steel
11. Body Material ASTM A182 Gr F55
12. Obturator Material Super Duplex (UNS S32760)
13. Seat Material Super Duplex (UNS S32760)
14. Seat Insert PEEK
15. Spring (Seat) Material UNS N07750
16. Stem Material ASTM A276 (UNS S32760)
17. Seat-Stem Seal Group E (acc. item A.7.1.5.6)
18. Operator Type Gearbox
19. Additional Requirement N/A
20. Seat Type (For trunnion-mounted) Side A: SPE / Side B: SPE; DBB
21. Bore Type Full Bore
22. Body Construction split body, bolted
23. Cladding or Coating N/A
24. Valve Testing FAT according A.9.3
25. Notes N/A
Valve Code VES-1500-1-S214

Specs G3
1. Valve Type Ball
5. Standard API 6D / IOGP S-562
7. End Connection ASME B16.5, RTJ
8. Pressure Class 1500
10. Material Class Stainless Steel
12. Obturator Material AISI 316
13. Seat Material AISI 316
17. Seat-Stem Seal Group B (acc. item A.7.1.5.6)
25. Notes N/A
N/A Page 1 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
9. Temperature 0°C to 150°C
17. Seat-Stem Seal Group C (acc. item A.7.1.5.6)
25. Notes N/A

Specs G3
1. Valve Type Ball
25. Notes N/A
N/A Page 2 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
2. Sealing Type Metal to Metal
12. Obturator Material AISI 316 + Tungsten carbide coating
13. Seat Material AISI 316 + Tungsten carbide coating
14. Seat Insert N/A
20. Seat Type (For trunnion-mounted) Side A: SPE / Side B: SPE
25. Notes N/A

Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 3 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
16. Stem Material ASTM B637 (UNS N07718)
25. Notes N/A

Specs G3
1. Valve Type Ball
25. Notes N/A
N/A Page 4 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
20. Seat Type (For trunnion-mounted) Side A: SPE / Side B: DPE; DIB-2 & DBB
25. Notes N/A
Valve Code VES-1500-2-S21F

Specs G3
1. Valve Type Ball
19. Additional Requirement Fire Tested (acc. item A.6.1.4); Fugitive Emission (acc. item A.6.1.6)
25. Notes N/A
N/A Page 5 of 842

N/A
N/A
N/A
Valve Code VES-1500-2-S21G
Specs G3
1. Valve Type Ball
25. Notes N/A

Specs G3
1. Valve Type Ball
25. Notes N/A
N/A Page 6 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
25. Notes N/A

Specs G3
1. Valve Type Ball
25. Notes N/A
N/A Page 7 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
25. Notes N/A

Specs G3
1. Valve Type Ball
25. Notes N/A
N/A Page 8 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
25. Notes N/A

Specs G3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 9 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs G3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 10 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 11 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A

Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 12 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A

Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 13 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A

Specs G3
1. Valve Type Ball
25. Notes N/A
N/A Page 14 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
19. Additional Requirement Fire Tested (acc. item A.6.1.4)
25. Notes N/A

Specs G3
1. Valve Type Ball
25. Notes N/A
N/A Page 15 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
25. Notes N/A

Specs G3
1. Valve Type Ball
25. Notes N/A
N/A Page 16 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
25. Notes N/A

Specs G3
1. Valve Type Ball
25. Notes N/A
N/A Page 17 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
25. Notes N/A

Specs G3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes Acceptance criteria for sealing tests see Annex A
N/A Page 18 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
14. Seat Insert N/A

Specs G3
1. Valve Type Ball
14. Seat Insert N/A
N/A Page 19 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A

Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
N/A Page 20 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A

Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
N/A Page 21 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A

Specs G3
1. Valve Type Ball
14. Seat Insert N/A
18. Operator Type Actuated
20. Seat Type (For trunnion-mounted) Side A: SPE / Side B: DPE; DIB-2 & DBB (notes)
25. Notes Acceptance criteria for sealing tests see Annex A, DBB tests to be performed
at both conditions, fully opened and closed, Vent and drain connections
according Annex A
N/A Page 22 of 842

N/A
N/A
N/A
Valve Code VES-1500-4-S25U
Specs G3
1. Valve Type Ball
14. Seat Insert N/A
according Annex A

Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A
N/A Page 23 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A
Valve Code VES-1500-4-S27U

Specs G3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A
N/A Page 24 of 842

N/A
N/A
N/A
Valve Code VES-150-1-C110
Specs B9 B10 B17
1. Valve Type Ball
4. Ball Mouting 2" - 4" Floating
6" - 38" Trunnion
7. End Connection 2" - 24" ASME B16.5, RF
26" - 38" ASME B16.47 Series A, RF
10. Material Class Carbon Steel
11. Body Material ASTM A105 or ASTM A216 Gr WCB + SS316 weld overlay (acc. item A.7.1.7.3)
14. Seat Insert PTFE reinforced with 25% Carbon
18. Operator Type 2" - 4" Lever
6" - 38" Gearbox
23. Cladding or Coating Partial clad - SS316 weld overlay on all body sealing areas
25. Notes N/A

Specs B9 B10
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 25 of 842

N/A
N/A
N/A
Specs B10
1. Valve Type Ball
6" - 38" Gearbox
25. Notes N/A

Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
17. Seat-Stem Seal Group D (acc. item A.7.1.5.6)
6" - 36" Gearbox
25. Notes N/A
N/A Page 26 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
17. Seat-Stem Seal Group A (acc. item A.7.1.5.6)
6" - 36" Gearbox
25. Notes N/A

Specs B4 B9 B10
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 27 of 842

N/A
N/A
N/A
Specs B4
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
6" - 38" Gearbox
25. Notes N/A

Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 28 of 842

N/A
N/A
N/A
Specs B9 B10
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
12. Obturator Material AISI 410 + Chrome-Nickel Spray and Fuse (acc. Item A.8.2.2.4)
13. Seat Material AISI 410 + Chrome-Nickel Spray and Fuse (acc. Item A.8.2.2.4)
14. Seat Insert N/A
17. Seat-Stem Seal Group F (acc. item A.7.1.5.6)
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
10. Material Class Low-Temperature Carbon Steel
11. Body Material ASTM A350 Gr LF2 CL1 or ASTM A352 Gr LCC + Inconel 625 weld overlay (acc.
item A.7.1.7.3)
6" - 36" Gearbox
23. Cladding or Coating Partial clad - Inconel 625 weld overlay on all body sealing areas
25. Notes N/A
N/A Page 29 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 30 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 31 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
10. Material Class Carbon Steel with Cladding
11. Body Material ASTM A105 or ASTM A216 Gr WCB + Inconel 625 weld overlay (acc. item
A.7.1.7.3)
12. Obturator Material ASTM A105 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
13. Seat Material ASTM A105 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
6" - 30" Gearbox
23. Cladding or Coating Full clad - Inconel 625 weld overlay on all wetted parts
25. Notes N/A

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 32 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
12. Obturator Material ASTM A105 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Tungsten
carbide coating
13. Seat Material ASTM A105 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Tungsten
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 33 of 842

N/A
N/A
N/A
Specs B26
1. Valve Type Ball
6" - 28" Trunnion
10. Material Class Duplex Steel
11. Body Material ASTM A995 Gr 1b
12. Obturator Material Duplex (UNS S32550)
13. Seat Material Duplex (UNS S32550)
6" - 28" Gearbox
25. Notes N/A

Specs B11 B26
1. Valve Type Ball
4. Ball Mouting Floating
5. Standard API 6D
6. Size Range (NPS) 1" - 1 ½"
7. End Connection Flange ASME B16.5, RF
13. Seat Material PTFE reinforced with 25% Carbon
14. Seat Insert N/A
15. Spring (Seat) Material N/A
18. Operator Type Lever
20. Seat Type N/A
25. Notes N/A
N/A Page 34 of 842

N/A
N/A
N/A
Specs B11 B16 B26
1. Valve Type Ball
6" - 36" Trunnion
11. Body Material ASTM A182 Gr F51 or ASTM A995 Gr 4A
6" - 36" Gearbox
25. Notes N/A

Specs B11 B26
1. Valve Type Ball
6" - 36" Gearbox
25. Notes N/A
N/A Page 35 of 842

N/A
N/A
N/A
Specs B16
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B16
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 36 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 37 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
11. Body Material ASTM A182 Gr F316 or ASTM A351 Gr CF8M
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 38 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 39 of 842

N/A
N/A
N/A
Valve Code VES-150-1-U300
Specs B7 B14 B23
1. Valve Type Ball
5. Standard API 6D
6. Size Range (NPS) ½" - 1 ½"
10. Material Class Uncommon Materials
11. Body Material ASTM B148 (UNS C95800)
12. Obturator Material ASTM B148 (UNS C95800)
14. Seat Insert N/A
16. Stem Material Monel K500
20. Seat Type N/A
25. Notes N/A

Specs B7 B14 B22 B23
1. Valve Type Ball
6" - 24" Trunnion
5. Standard API 6D
7. End Connection ASME B16.5, RF
13. Seat Material ASTM B148 (UNS C95800)
6" - 24" Gearbox
20. Seat Type N/A
25. Notes N/A
N/A Page 40 of 842

N/A
N/A
N/A
Specs B14 B22 B23
1. Valve Type Ball
5. Standard API 6D
6" - 36" Gearbox
25. Notes N/A

Specs B23
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 41 of 842

N/A
N/A
N/A
Specs F3 G3
1. Valve Type Ball
5. Standard ASME B16.34 LTD
7. End Connection socket weld ends ASME B16.11 with nipple SCH 80/80S
11. Body Material ASTM A182 Gr F316/316L
25. Notes N/A

Specs F3 G3
1. Valve Type Ball
12. Obturator Material AISI 316 + Hard Coating (acc. Item A.7.1.7.4)
13. Seat Material AISI 316 + Hard Coating (acc. Item A.7.1.7.4)
14. Seat Insert N/A
25. Notes N/A
N/A Page 42 of 842

N/A
N/A
N/A
Specs F3 G3
1. Valve Type Ball
25. Notes N/A

Specs F3 G3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 43 of 842

N/A
N/A
N/A
Valve Code VES-1502-2-S2F1
Specs F3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs F3 G3
1. Valve Type Ball
25. Notes N/A
N/A Page 44 of 842

N/A
N/A
N/A
Specs F3 G3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
Valve Code VES-1502-2-S2FB

Specs G3
1. Valve Type Ball
25. Notes N/A
N/A Page 45 of 842

N/A
N/A
N/A
Specs F3 G3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs F3 G3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 46 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B10 B17
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 47 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 38" Gearbox
25. Notes N/A

Specs B17
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 48 of 842

N/A
N/A
N/A
Valve Code VES-150-2-C11F
Specs B9 B10
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B9 B10
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 49 of 842

N/A
N/A
N/A
Specs B9 B10
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 50 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 51 of 842

N/A
N/A
N/A
Valve Code VES-150-2-C13G
Specs B9 B10 B17
1. Valve Type Ball
6" - 38" Gearbox
25. Notes N/A

Specs B9 B10 B17
1. Valve Type Ball
6" - 38" Trunnion
14. Seat Insert N/A
6" - 38" Gearbox
25. Notes N/A
N/A Page 52 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B4 B9 B10
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 53 of 842

N/A
N/A
N/A
Specs B4 B9
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B9 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 54 of 842

N/A
N/A
N/A
Specs B9 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 55 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B9
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 56 of 842

N/A
N/A
N/A
Specs B9
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 57 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A
N/A Page 58 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A
N/A Page 59 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A
N/A Page 60 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A
N/A Page 61 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 62 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 63 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 64 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 65 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 66 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 67 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
6" - 30" Gearbox

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 68 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 69 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 70 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 71 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 36" Gearbox

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 72 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
12. Obturator Material ASTM A105 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Chrome-Nickel
Spray and Fuse (acc. Item A.8.2.2.4)
13. Seat Material ASTM A105 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Chrome-Nickel
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 73 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox

Specs B11 B26
1. Valve Type Ball
6" - 28" Trunnion
6" - 28" Gearbox
25. Notes N/A
N/A Page 74 of 842

N/A
N/A
N/A
Specs B11 B26
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B11 B16 B26
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 75 of 842

N/A
N/A
N/A
Specs B16 B26
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
Valve Code VES-150-2-D21F

Specs B11 B16
1. Valve Type Ball
6" - 28" Trunnion
6" - 28" Gearbox
25. Notes N/A
N/A Page 76 of 842

N/A
N/A
N/A
Valve Code VES-150-2-D21G
Specs B11 B16
1. Valve Type Ball
6" - 28" Trunnion
6" - 28" Gearbox
25. Notes N/A

Specs B16
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 77 of 842

N/A
N/A
N/A
Specs B16
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B11 B16 B26
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 78 of 842

N/A
N/A
N/A
Specs B16
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B11 B16
1. Valve Type Ball
6" - 28" Trunnion
6" - 28" Gearbox
25. Notes N/A
N/A Page 79 of 842

N/A
N/A
N/A
Specs B11 B16
1. Valve Type Ball
6" - 28" Trunnion
6" - 28" Gearbox
25. Notes N/A
Valve Code VES-150-2-D2F0

Specs B11
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 80 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 81 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Ball
6" - 36" Gearbox
25. Notes N/A

Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 82 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 83 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Gearbox
25. Notes N/A
N/A Page 84 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Gearbox
25. Notes N/A
N/A Page 85 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 86 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 87 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 88 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 89 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 90 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 91 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 92 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 93 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 94 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
25. Notes N/A
N/A Page 95 of 842

N/A
N/A
N/A
Specs B7 B14 B23
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B7 B14 B22 B23
1. Valve Type Ball
6" - 24" Trunnion
5. Standard API 6D
6" - 24" Gearbox
20. Seat Type N/A
25. Notes N/A
N/A Page 96 of 842

N/A
N/A
N/A
Specs B7
1. Valve Type Ball
5. Standard API 6D
20. Seat Type N/A
25. Notes N/A

Specs B14 B27
1. Valve Type Ball
5. Standard Manufacturer standard
7. End Connection ASME B16.1, FF
11. Body Material ASTM A395 60-40-18 + PFA liner
12. Obturator Material Stainless Steel + PFA liner
13. Seat Material PTFE
14. Seat Insert N/A
16. Stem Material According manufacturer standard, fitted to service conditions
17. Seat-Stem Seal According to manufacturer standard, fitted to service conditions
20. Seat Type N/A
24. Valve Testing FAT according manufacturer standard
25. Notes N/A
N/A Page 97 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
11. Body Material ASTM A105 + SS316 weld overlay (acc. item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A

Specs B9 B10
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 98 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B9 B10
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 99 of 842

N/A
N/A
N/A
Specs B9 B10
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 100 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 101 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox

Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 102 of 842

N/A
N/A
N/A
Specs B9 B10
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B4 B9
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 103 of 842

N/A
N/A
N/A
Specs B4 B9
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B9 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 104 of 842

N/A
N/A
N/A
Specs B9 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 105 of 842

N/A
N/A
N/A
Specs B9
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B9
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 106 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
11. Body Material ASTM A350 Gr LF2 CL1 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A
N/A Page 107 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 108 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 109 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 110 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 111 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 112 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 113 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B6 B19
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 114 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
11. Body Material ASTM A105 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 115 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 116 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 117 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 118 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 119 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 120 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox

Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 121 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A

Specs B16 B26
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 122 of 842

N/A
N/A
N/A
Specs B11 B16
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B11 B16
1. Valve Type Ball
6" - 28" Trunnion
6" - 28" Gearbox
25. Notes N/A
N/A Page 123 of 842

N/A
N/A
N/A
Specs B11 B16 B26
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B16
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 124 of 842

N/A
N/A
N/A
Specs B16
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B16
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 125 of 842

N/A
N/A
N/A
Specs B11 B16
1. Valve Type Ball
6" - 28" Trunnion
6" - 28" Gearbox
25. Notes N/A

Specs B16
1. Valve Type Ball
6" - 36" Trunnion
12. Obturator Material Duplex (UNS S31803) + Tungsten carbide coating
13. Seat Material Duplex (UNS S31803) + Tungsten carbide coating
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 126 of 842

N/A
N/A
N/A
Specs B16
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox

Specs B11 B16
1. Valve Type Ball
6" - 28" Trunnion
14. Seat Insert N/A
6" - 28" Gearbox
N/A Page 127 of 842

N/A
N/A
N/A
Specs B16
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox

Specs B16
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 128 of 842

N/A
N/A
N/A
Specs B16
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox

Specs B16
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 129 of 842

N/A
N/A
N/A
Specs B11 B16
1. Valve Type Ball
6" - 28" Trunnion
14. Seat Insert N/A
6" - 28" Gearbox

Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 130 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 131 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B12
1. Valve Type Ball
6" - 36" Trunnion
12. Obturator Material Super Duplex (UNS S32760) + Tungsten carbide coating
13. Seat Material Super Duplex (UNS S32760) + Tungsten carbide coating
14. Seat Insert N/A
6" - 36" Gearbox
according Annex A
N/A Page 132 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
according Annex A

Specs B12
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
according Annex A
N/A Page 133 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
according Annex A

Specs B12
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
according Annex A
N/A Page 134 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
according Annex A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 135 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 136 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 137 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
6" - 36" Gearbox
25. Notes N/A
N/A Page 138 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 139 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 140 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 141 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox
N/A Page 142 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 36" Gearbox

Specs B9 B17
1. Valve Type Ball
6" - 36" Trunnion
14. Seat Insert N/A
according Annex A
N/A Page 143 of 842

N/A
N/A
N/A
Specs B9
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A

Specs B9 B17
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
14. Seat Insert N/A
according Annex A
N/A Page 144 of 842

N/A
N/A
N/A
Specs B9
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A
Valve Code VES-2502-1-N108

Specs H30
1. Valve Type Ball
7. End Connection butt weld ASME B16.25 with nipple SCH 80S
10. Material Class Nickel Alloys
11. Body Material ASTM B564 (UNS N06625)
12. Obturator Material ASTM B564 (UNS N06625)
13. Seat Material ASTM B564 (UNS N06625)
25. Notes N/A
N/A Page 145 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
12. Obturator Material ASTM B564 (UNS N06625) + Hard Coating (acc. Item A.7.1.7.4)
13. Seat Material ASTM B564 (UNS N06625) + Hard Coating (acc. Item A.7.1.7.4)
14. Seat Insert N/A
25. Notes N/A

Specs H12P H12
1. Valve Type Ball
25. Notes N/A
N/A Page 146 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
12. Obturator Material Super Duplex (UNS S32760) + Hard Coating (acc. Item A.7.1.7.4)
13. Seat Material Super Duplex (UNS S32760) + Hard Coating (acc. Item A.7.1.7.4)
14. Seat Insert N/A
25. Notes N/A

Specs H12
1. Valve Type Ball
25. Notes N/A
N/A Page 147 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
Valve Code VES-2502-2-D3G8

Specs H12P H12
1. Valve Type Ball
25. Notes N/A
N/A Page 148 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
25. Notes N/A

Specs H30
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 149 of 842

N/A
N/A
N/A
Valve Code VES-2502-2-N1F8
Specs H30
1. Valve Type Ball
25. Notes N/A

Specs H30
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 150 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
6. Size Range (NPS) 1"
25. Notes N/A

Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 151 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
25. Notes N/A

Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 152 of 842

N/A
N/A
N/A
Valve Code VES-2502-2-S2G8
Specs H3
1. Valve Type Ball
25. Notes N/A

Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 153 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H30
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 154 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 155 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H6
1. Valve Type Ball
7. End Connection butt weld ASME B16.25 with nipple SCH 160
11. Body Material ASTM A350 Gr LF2 CL1
25. Notes N/A
N/A Page 156 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
Valve Code VES-2503-2-C2F8

Specs H6
1. Valve Type Ball
25. Notes N/A
N/A Page 157 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H3
1. Valve Type Ball
25. Notes N/A
N/A Page 158 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H3
1. Valve Type Ball
6. Size Range (NPS) 1 ½"
25. Notes N/A
N/A Page 159 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
Valve Code VES-2503-2-S2G8

Specs H3
1. Valve Type Ball
25. Notes N/A
N/A Page 160 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H6
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 161 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 162 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
7. End Connection ISO 27509, IX
25. Notes N/A

Specs H6
1. Valve Type Ball
25. Notes N/A
N/A Page 163 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
25. Notes N/A

Specs H6
1. Valve Type Ball
25. Notes N/A
N/A Page 164 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
25. Notes N/A

Specs H6
1. Valve Type Ball
25. Notes N/A
N/A Page 165 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H6
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 166 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A

Specs H6
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 167 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A

Specs H6
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 168 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
25. Notes N/A

Specs H30
1. Valve Type Ball
25. Notes N/A
N/A Page 169 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
25. Notes N/A

Specs H30
1. Valve Type Ball
25. Notes N/A
N/A Page 170 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
25. Notes N/A

Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
25. Notes N/A
N/A Page 171 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
25. Notes N/A

Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
25. Notes N/A
N/A Page 172 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
25. Notes N/A

Specs H12P H12
1. Valve Type Ball
25. Notes N/A
N/A Page 173 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
25. Notes N/A

Specs H12P H12
1. Valve Type Ball
25. Notes N/A
N/A Page 174 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
25. Notes N/A

Specs H12P H12
1. Valve Type Ball
25. Notes N/A
N/A Page 175 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
25. Notes N/A

Specs H12P H12
1. Valve Type Ball
25. Notes N/A
N/A Page 176 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
25. Notes N/A

Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 177 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 178 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H12P H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 179 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A

Specs H12P H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 180 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A

Specs H3
1. Valve Type Ball
25. Notes N/A
N/A Page 181 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
25. Notes N/A

Specs H3
1. Valve Type Ball
25. Notes N/A
N/A Page 182 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
25. Notes N/A

Specs H3
1. Valve Type Ball
25. Notes N/A
N/A Page 183 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
25. Notes N/A

Specs H3
1. Valve Type Ball
25. Notes N/A
N/A Page 184 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
25. Notes N/A

Specs H3
1. Valve Type Ball
25. Notes N/A
N/A Page 185 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
25. Notes N/A

Specs H3
1. Valve Type Ball
25. Notes N/A
N/A Page 186 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
25. Notes N/A

Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 187 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A
N/A Page 188 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
14. Seat Insert N/A
25. Notes N/A

Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 189 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A

Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 190 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A

Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A
N/A Page 191 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
25. Notes N/A

Specs H6
1. Valve Type Ball
14. Seat Insert N/A
N/A Page 192 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
14. Seat Insert N/A

Specs H6
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
N/A Page 193 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A

Specs H6
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
N/A Page 194 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A

Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
N/A Page 195 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A

Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
N/A Page 196 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A

Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
N/A Page 197 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A

Specs H12P H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
N/A Page 198 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A

Specs H3
1. Valve Type Ball
14. Seat Insert N/A
N/A Page 199 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
14. Seat Insert N/A

Specs H3
1. Valve Type Ball
14. Seat Insert N/A
N/A Page 200 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A

Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
N/A Page 201 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A

Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
N/A Page 202 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A

Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
according Annex A
N/A Page 203 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
19. Additional Requirement Fire Tested (acc. item A.6.1.4), Fire Tested (acc. item A.6.1.4); SIL-3 (see notes)
24. Valve Testing FAT according A.9.3 and HIPPS in place test according A.9.3.7
at both conditions, fully opened and closed, The manufacturer shall present
all documentation in order to certify that SIL 3 requirements were achieved
for the valve design, Vent and drain connections according Annex A
Valve Code VES-2510-4-C57E

Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
19. Additional Requirement Fire Tested (acc. item A.6.1.4); Fugitive Emission (acc. item A.6.1.6); SIL-3 (see
notes)
N/A Page 204 of 842

N/A
N/A
N/A
Valve Code VES-2510-4-C57U
Specs H30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
according Annex A

Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
according Annex A
N/A Page 205 of 842

N/A
N/A
N/A
Valve Code VES-2510-4-D35U
Specs H12P H12
1. Valve Type Ball
14. Seat Insert N/A
according Annex A

Specs H12P H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A
N/A Page 206 of 842

N/A
N/A
N/A
Specs H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
19. Additional Requirement Fire Tested (acc. item A.6.1.4), Fire Tested (acc. item A.6.1.4); SIL-3 (see notes)
Valve Code VES-2510-4-D37E

Specs H12P H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
notes)
N/A Page 207 of 842

N/A
N/A
N/A
Valve Code VES-2510-4-D37U
Specs H12P H12
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 208 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 209 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 210 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 211 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
item A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
item A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 212 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 213 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 214 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A

Specs C11
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 215 of 842

N/A
N/A
N/A
Specs C11 C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C11
1. Valve Type Ball
6" - 36" Gearbox
25. Notes N/A
N/A Page 216 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 217 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 218 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 219 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 220 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 221 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 222 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 223 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 224 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 225 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 226 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 227 of 842

N/A
N/A
N/A
Specs C4 C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 228 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 229 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 230 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 231 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 232 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
item A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
item A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 233 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
item A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C6 C19
1. Valve Type Ball
item A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A
N/A Page 234 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
item A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
item A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 235 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
item A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
item A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 236 of 842

N/A
N/A
N/A
Specs C19
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A

Specs C6
1. Valve Type Ball
6" - 24" Trunnion
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
6" - 24" Gearbox
25. Notes N/A
N/A Page 237 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 36" Trunnion
5. Standard API 6D
A.7.1.7.3)
6" - 36" Gearbox
25. Notes N/A
N/A Page 238 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 239 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 240 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A
N/A Page 241 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
A.7.1.7.3)
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 242 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 243 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 244 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 245 of 842

N/A
N/A
N/A
Specs C11
1. Valve Type Ball
6" - 20" Trunnion
6" - 20" Gearbox
25. Notes N/A

Specs C11
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 246 of 842

N/A
N/A
N/A
Specs C11 C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 247 of 842

N/A
N/A
N/A
Specs C11 C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 36" Gearbox
25. Notes N/A
N/A Page 248 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 249 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 250 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 251 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 252 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 253 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 254 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 255 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
25. Notes N/A
N/A Page 256 of 842

N/A
N/A
N/A
Specs C11
1. Valve Type Ball
5. Standard API 6D
8. Pressure Class 150, 300
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 257 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 258 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 259 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 260 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 261 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 262 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 263 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 264 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 265 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A
N/A Page 266 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 30" Gearbox
25. Notes N/A

Specs C4 C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 267 of 842

N/A
N/A
N/A
Specs C4 C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 268 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 269 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 270 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
N/A Page 271 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
N/A Page 272 of 842

N/A
N/A
N/A
Specs C4 C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox

Specs C4 C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
N/A Page 273 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
N/A Page 274 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
N/A Page 275 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 32" Gearbox
N/A Page 276 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 277 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 278 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 279 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox

Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 280 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox

Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 281 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 30" Gearbox

Specs C6 C19
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 282 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 283 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 284 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 285 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 286 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 287 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 288 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox

Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 289 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
6" - 30" Gearbox

Specs C11 C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 290 of 842

N/A
N/A
N/A
Specs C11 C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 291 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 292 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A
N/A Page 293 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
6" - 32" Gearbox
25. Notes N/A

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
N/A Page 294 of 842

N/A
N/A
N/A
Specs C11 C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox

Specs C11 C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
N/A Page 295 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
N/A Page 296 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox

Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox
N/A Page 297 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
6" - 32" Gearbox

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 298 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 299 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 300 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 301 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 302 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox

Specs C12
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 303 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 304 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 305 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 306 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
6" - 30" Gearbox
25. Notes N/A
N/A Page 307 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 308 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
14. Seat Insert N/A
6" - 30" Gearbox

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 309 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 30" Gearbox

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 310 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 30" Gearbox

Specs C3
1. Valve Type Ball
6" - 30" Trunnion
5. Standard API 6D
14. Seat Insert N/A
6" - 30" Gearbox
N/A Page 311 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
14. Seat Insert N/A
according Annex A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
according Annex A
N/A Page 312 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
according Annex A

Specs C10
1. Valve Type Ball
6" - 32" Trunnion
5. Standard API 6D
14. Seat Insert N/A
according Annex A
N/A Page 313 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
14. Seat Insert N/A
according Annex A

Specs C16
1. Valve Type Ball
14. Seat Insert N/A
according Annex A
N/A Page 314 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Ball
14. Seat Insert N/A
according Annex A

Specs C12
1. Valve Type Ball
14. Seat Insert N/A
according Annex A
N/A Page 315 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Ball
14. Seat Insert N/A
according Annex A
Valve Code VES-600-1-A534

Specs E32
1. Valve Type Ball
10. Material Class Alloy Steel
11. Body Material ASTM A350 Gr LF3 or ASTM A352 Gr LC3 + Inconel 625 weld overlay (acc.
item A.7.1.7.3)
12. Obturator Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
13. Seat Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
4" Gearbox
25. Notes N/A
N/A Page 316 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
26" ASME B16.47 Series A, RF
item A.7.1.7.3)
4" - 26" Gearbox
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
item A.7.1.7.3)
4" - 26" Gearbox
25. Notes N/A
N/A Page 317 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
A.7.1.7.3)
4" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
A.7.1.7.3)
4" Gearbox
25. Notes N/A
N/A Page 318 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" Gearbox
25. Notes N/A
N/A Page 319 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
14. Seat Insert N/A
4" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 320 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 321 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A
N/A Page 322 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A
N/A Page 323 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A
N/A Page 324 of 842

N/A
N/A
N/A
Specs E32
1. Valve Type Ball
item A.7.1.7.3)
4" - 16" Gearbox
25. Notes N/A

Specs E32
1. Valve Type Ball
item A.7.1.7.3)
4" - 16" Gearbox
25. Notes N/A
N/A Page 325 of 842

N/A
N/A
N/A
Valve Code VES-600-2-A53F
Specs E32
1. Valve Type Ball
item A.7.1.7.3)
4" - 16" Gearbox
25. Notes N/A
Valve Code VES-600-2-A53G

Specs E32
1. Valve Type Ball
item A.7.1.7.3)
4" - 16" Gearbox
25. Notes N/A
N/A Page 326 of 842

N/A
N/A
N/A
Specs E32
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
12. Obturator Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Tungsten
carbide coating
13. Seat Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Tungsten
carbide coating
14. Seat Insert N/A
4" - 16" Gearbox
25. Notes N/A

Specs E32
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 16" Gearbox
25. Notes N/A
N/A Page 327 of 842

N/A
N/A
N/A
Specs E32
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 16" Gearbox
25. Notes N/A

Specs E32
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
12. Obturator Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Chrome-
Nickel Spray and Fuse (acc. Item A.8.2.2.4)
13. Seat Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Chrome-
14. Seat Insert N/A
4" - 16" Gearbox
25. Notes N/A
N/A Page 328 of 842

N/A
N/A
N/A
Specs E32
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
4" - 16" Gearbox
25. Notes N/A
Valve Code VES-600-2-A58F

Specs E32
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
4" - 16" Gearbox
25. Notes N/A
N/A Page 329 of 842

N/A
N/A
N/A
Specs E32
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
4" - 16" Gearbox
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
item A.7.1.7.3)
4" - 26" Gearbox
25. Notes N/A
N/A Page 330 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
item A.7.1.7.3)
4" - 26" Gearbox
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
item A.7.1.7.3)
4" - 26" Gearbox
25. Notes N/A
N/A Page 331 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
item A.7.1.7.3)
4" - 26" Gearbox
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
item A.7.1.7.3)
4" - 26" Gearbox
25. Notes N/A
N/A Page 332 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
item A.7.1.7.3)
4" - 26" Gearbox
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
item A.7.1.7.3)
4" - 26" Gearbox
25. Notes N/A
N/A Page 333 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
item A.7.1.7.3)
4" - 26" Gearbox
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
item A.7.1.7.3)
14. Seat Insert N/A
4" - 26" Gearbox
25. Notes N/A
N/A Page 334 of 842

N/A
N/A
N/A
Specs E6
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
4" - 26" Gearbox
25. Notes N/A

Specs E19
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A
N/A Page 335 of 842

N/A
N/A
N/A
Specs E19
1. Valve Type Ball
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
A.7.1.7.3)
4" - 36" Gearbox
25. Notes N/A
N/A Page 336 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
A.7.1.7.3)
4" - 24" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
A.7.1.7.3)
4" - 24" Gearbox
25. Notes N/A
N/A Page 337 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
A.7.1.7.3)
4" - 24" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
A.7.1.7.3)
4" - 24" Gearbox
25. Notes N/A
N/A Page 338 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
A.7.1.7.3)
4" - 24" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
A.7.1.7.3)
4" - 24" Gearbox
25. Notes N/A
N/A Page 339 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
A.7.1.7.3)
4" - 24" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A
N/A Page 340 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A
N/A Page 341 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A
N/A Page 342 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A
N/A Page 343 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A

Specs E30
1. Valve Type Ball
5. Standard API 6D
A.7.1.7.3)
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A
N/A Page 344 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 345 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 346 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 347 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 348 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 349 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A
N/A Page 350 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A
N/A Page 351 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A
N/A Page 352 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A
N/A Page 353 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A
N/A Page 354 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A
N/A Page 355 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A
N/A Page 356 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A
N/A Page 357 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A
N/A Page 358 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A
N/A Page 359 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
25. Notes N/A

Specs E32
1. Valve Type Ball
5. Standard API 6D
11. Body Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 16" Gearbox
N/A Page 360 of 842

N/A
N/A
N/A
Specs E32
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
4" - 16" Gearbox

Specs E32
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
4" - 16" Gearbox
N/A Page 361 of 842

N/A
N/A
N/A
Specs E32
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 16" Gearbox

Specs E32
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 16" Gearbox
N/A Page 362 of 842

N/A
N/A
N/A
Specs E32
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 16" Gearbox

Specs E6 E19
1. Valve Type Ball
4" - 26" Gearbox
25. Notes N/A
N/A Page 363 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
4" - 26" Gearbox
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
4" - 26" Gearbox
25. Notes N/A
N/A Page 364 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
4" - 26" Gearbox
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
4" - 26" Gearbox
25. Notes N/A
N/A Page 365 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
4" - 26" Gearbox
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
4" - 26" Gearbox
N/A Page 366 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
4" - 26" Gearbox

Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
4" - 26" Gearbox
N/A Page 367 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
4" - 26" Gearbox

Specs E6 E19
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 26" Gearbox
N/A Page 368 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 26" Gearbox

Specs E19
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 24" Gearbox
25. Notes N/A
N/A Page 369 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox

Specs E30
1. Valve Type Ball
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox
N/A Page 370 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox

Specs E30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox
N/A Page 371 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox

Specs E30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox
N/A Page 372 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
4" - 24" Gearbox

Specs E30
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 20" Gearbox
N/A Page 373 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 24" Gearbox

Specs E30
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 24" Gearbox
N/A Page 374 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 375 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 376 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 377 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs E16
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 378 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox

Specs E16
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox
N/A Page 379 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox

Specs E16
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox
N/A Page 380 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox

Specs E16
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox
N/A Page 381 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox

Specs E16
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox
N/A Page 382 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A
N/A Page 383 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A
N/A Page 384 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A
N/A Page 385 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A

Specs E3
1. Valve Type Ball
4" - 32" Gearbox
25. Notes N/A
N/A Page 386 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
14. Seat Insert N/A
4" - 32" Gearbox

Specs E3
1. Valve Type Ball
14. Seat Insert N/A
4" - 32" Gearbox
N/A Page 387 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
14. Seat Insert N/A
4" - 32" Gearbox

Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
N/A Page 388 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox

Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
N/A Page 389 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox

Specs E3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 32" Gearbox
N/A Page 390 of 842

N/A
N/A
N/A
Specs E32
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
according Annex A

Specs E32
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A
N/A Page 391 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
according Annex A

Specs E6 E19
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A
N/A Page 392 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
according Annex A

Specs E30
1. Valve Type Ball
5. Standard API 6D
carbide coating
carbide coating
14. Seat Insert N/A
according Annex A
N/A Page 393 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A

Specs B16 C16
1. Valve Type Ball
5. Standard ISO 17292
7. End Connection socket weld ends ASME B16.11 with nipple SCH 40S
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 394 of 842

N/A
N/A
N/A
Specs B16 C16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E16
1. Valve Type Ball
13. Seat Material PEEK
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 395 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B16 C16 E16
1. Valve Type Ball
12. Obturator Material Duplex (UNS S31803) + Hard Coating (acc. Item A.7.1.7.4)
13. Seat Material Duplex (UNS S31803) + Hard Coating (acc. Item A.7.1.7.4)
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 396 of 842

N/A
N/A
N/A
Specs B12 C12
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B12 C12
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 397 of 842

N/A
N/A
N/A
Specs B30 C30
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B30 C30
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 398 of 842

N/A
N/A
N/A
Specs E30 E32
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B30 C30 E30 E32
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 399 of 842

N/A
N/A
N/A
Specs B3 C3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B3 C3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 400 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 401 of 842

N/A
N/A
N/A
Specs B3 C3 E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B16 C16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 402 of 842

N/A
N/A
N/A
Specs B16 C16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 403 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B16 C16 E16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 404 of 842

N/A
N/A
N/A
Specs B16 C16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B16 C16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 405 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 406 of 842

N/A
N/A
N/A
Specs B16 C16 E16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B12 C12
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 407 of 842

N/A
N/A
N/A
Specs B12 C12
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B12 C12
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 408 of 842

N/A
N/A
N/A
Specs B12 C12
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B30 C30
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 409 of 842

N/A
N/A
N/A
Specs B30 C30
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E30 E32
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 410 of 842

N/A
N/A
N/A
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E32
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 411 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B30 C30
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 412 of 842

N/A
N/A
N/A
Specs B30 C30
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E30
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 413 of 842

N/A
N/A
N/A
Specs E30 E32
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 414 of 842

N/A
N/A
N/A
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B30 C30
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 415 of 842

N/A
N/A
N/A
Specs B3 C3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B3 C3 E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 416 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 417 of 842

N/A
N/A
N/A
Specs B3 C3 E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 418 of 842

N/A
N/A
N/A
Specs B3 C3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B3 C3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 419 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 420 of 842

N/A
N/A
N/A
Specs B3 C3 E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 421 of 842

N/A
N/A
N/A
Specs B16 C16 E16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B16 C16 E16
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 422 of 842

N/A
N/A
N/A
Specs B12 C12
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B12 C12
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 423 of 842

N/A
N/A
N/A
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 424 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 425 of 842

N/A
N/A
N/A
Specs B3 C3 E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B3 C3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 426 of 842

N/A
N/A
N/A
Specs B3 C3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 427 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B3 C3 E3
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 428 of 842

N/A
N/A
N/A
Specs B4
1. Valve Type Ball
11. Body Material ASTM A105
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B4
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 429 of 842

N/A
N/A
N/A
Specs B4
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B9 B10 C10
1. Valve Type Ball
7. End Connection socket weld ends ASME B16.11 with nipple SCH 160
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 430 of 842

N/A
N/A
N/A
Specs B9 B10 C10
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B9 B10 C10
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 431 of 842

N/A
N/A
N/A
Specs B6 B19 C6 C19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 432 of 842

N/A
N/A
N/A
Specs B6 B19 C6 C19 E6 E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B9 B10 C10
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 433 of 842

N/A
N/A
N/A
Specs B9 B10 C10
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B9 B10 C10
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 434 of 842

N/A
N/A
N/A
Specs B9 B10 C10
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B9 B10 C10
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 435 of 842

N/A
N/A
N/A
Specs B6 B19 C6 C19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B6 B19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 436 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 437 of 842

N/A
N/A
N/A
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 438 of 842

N/A
N/A
N/A
Specs B6 B19 C6 C19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B6 B19 C6 C19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 439 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 440 of 842

N/A
N/A
N/A
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
Valve Code VES-803-2-C2FA

Specs E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 441 of 842

N/A
N/A
N/A
Specs B10 C10
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B9 B10 C10
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 442 of 842

N/A
N/A
N/A
Specs B9 B10 C10
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 443 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 444 of 842

N/A
N/A
N/A
Specs B6 B19 C6 C19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B6 B19 C6 C19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 445 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs E6 E19
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 446 of 842

N/A
N/A
N/A
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B17
1. Valve Type Ball
6. Size Range (NPS) ¾" - 1 ½"
7. End Connection socket weld ends ASME B16.11 with nipple SCH XXS
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 447 of 842

N/A
N/A
N/A
Specs B17
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B17
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 448 of 842

N/A
N/A
N/A
Specs B17
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B17
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 449 of 842

N/A
N/A
N/A
Specs B17
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A

Specs B17
1. Valve Type Ball
14. Seat Insert N/A
20. Seat Type N/A
25. Notes N/A
N/A Page 450 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
14. Seat Insert Devlon V-API
4" - 18" Gearbox
25. Notes N/A
N/A Page 451 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 452 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A
N/A Page 453 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 454 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 455 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 456 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 457 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 458 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A
N/A Page 459 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A
N/A Page 460 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A
N/A Page 461 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A
N/A Page 462 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A
N/A Page 463 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
N/A Page 464 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 465 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 466 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 467 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A

Specs F3
1. Valve Type Ball
4" - 18" Gearbox
25. Notes N/A
N/A Page 468 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox

Specs F3
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox
N/A Page 469 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
14. Seat Insert N/A
4" - 18" Gearbox

Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
N/A Page 470 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox

Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
N/A Page 471 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox

Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox
N/A Page 472 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
4" - 18" Gearbox

Specs F3
1. Valve Type Ball
14. Seat Insert N/A
according Annex A
N/A Page 473 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A

Specs F3
1. Valve Type Ball
5. Standard API 6D
14. Seat Insert N/A
according Annex A
N/A Page 474 of 842

N/A
N/A
N/A
A.12.2 RISING STEM

Specs E32
1. Valve Type Rising Stem
5. Standard API 6D
item A.7.1.7.3)
12. Obturator Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Stellite
(Co-Cr Alloy acc. item A.8.2.1.2)
13. Seat Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Stellite
14. Seat Insert N/A
20. Seat Type N/A
22. Body Construction Top entry, solid body
25. Notes N/A

Specs E32
1. Valve Type Rising Stem
5. Standard API 6D
12. Obturator Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Stellite
13. Seat Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3) + Stellite
14. Seat Insert N/A
20. Seat Type N/A
22. Body Construction Top entry, solid body
25. Notes N/A
N/A Page 475 of 842

N/A
N/A
N/A
A.12.3 DOUBLE BALL VALVES
Valve Code VDE-10000-2-D301
Specs J12P J12
1. Valve Type Double Ball
4. Obturator Type Floating
5. Standard API 6A
6. Size Range (NPS) 1 ¹³/₁₆"
7. End Connection Flanged API 6A type 6BX
14. Seat Insert Material PEEK
15. Spring Material N/A
17. Stem Seal Material Group B (acc. item A.7.1.5.6)
19. Adiitional Requirement Fire Tested (acc. item A.6.1.4)
21. Bore Type Reduced Bore (min. 10mm)
22. Body Construction One piece forged body
23. Product Testing FAT according A.9.3
25. Notes Needle valve between balls for cavity-pressure relief Max weight 55kg
Minimum bore size 10mm

Specs J12P J12
5. Standard API 6A
17. Stem Seal Material Group E (acc. item A.7.1.5.6)
N/A Page 476 of 842

N/A
N/A
N/A
Specs J12P J12
4. Ball Mouting N/A
5. Standard API 6A
14. Seat Insert N/A
22. Body Construction Compact flangeless single body double ball valve. Face to face according
ASME B16.10
25. Notes All materials described in this datasheet are required for both valve, Needle
valve between balls for cavity-pressure relief
Valve Code VDE-10000-2-D37F

Specs J12P J12
4. Ball Mouting N/A
5. Standard API 6A
14. Seat Insert N/A
ASME B16.10
N/A Page 477 of 842

N/A
N/A
N/A
Valve Code VDE-10000-2-D3F1
Specs J12P J12
5. Standard API 6A
19. Adiitional Requirement Fire Tested (acc. item A.6.1.4); Fugitive Emission (acc. item A.6.1.6)

Specs J12P J12
5. Standard API 6A
7. End Connection Flanged API 6A type 6BX x NPT 1/2" ASME B1.20.1
N/A Page 478 of 842

N/A
N/A
N/A
Specs J12P J12
5. Standard API 6A

Specs J12P J12
5. Standard API 6A
14. Seat Insert Material N/A
N/A Page 479 of 842

N/A
N/A
N/A
Valve Code VDE-10000-2-N101
Specs J40
5. Standard API 6A

Specs J40
5. Standard API 6A
N/A Page 480 of 842

N/A
N/A
N/A
Specs J40
2. Sealing Type Metal to Metal, Soft
5. Standard API 6A

Specs J40
5. Standard API 6A
N/A Page 481 of 842

N/A
N/A
N/A
Specs J40
4. Ball Mouting N/A
5. Standard API 6A
14. Seat Insert N/A
ASME B16.10
Valve Code VDE-10000-2-N17F

Specs J40
4. Ball Mouting N/A
5. Standard API 6A
14. Seat Insert N/A
ASME B16.10
N/A Page 482 of 842

N/A
N/A
N/A
Valve Code VDE-10000-2-N1F1
Specs J40
5. Standard API 6A

Specs J40
5. Standard API 6A
N/A Page 483 of 842

N/A
N/A
N/A
Specs J40
5. Standard API 6A

Specs J40
5. Standard API 6A
N/A Page 484 of 842

N/A
N/A
N/A
Valve Code VDE-10000-2-N1G1
Specs J40
5. Standard API 6A
Valve Code VDE-10000-2-N1G2

Specs J40
5. Standard API 6A
N/A Page 485 of 842

N/A
N/A
N/A
Valve Code VDE-1500-2-S201
Specs G3
4. Obturator Type Trunnion
5. Standard ASME B16.34
6. Size Range (NPS) ½" - 2"
7. End Connection Flanged ASME B16.5, RTJ
15. Spring Material UNS N07750

Specs G3
7. End Connection Flanged ASME B16.5, RTJ x NPT 1/2" ASME B1.20.1
N/A Page 486 of 842

N/A
N/A
N/A
Specs G3

Specs G3
N/A Page 487 of 842

N/A
N/A
N/A
Specs G3

Specs G3
N/A Page 488 of 842

N/A
N/A
N/A
Specs G3
5. Standard API 6D
ASME B16.10

Specs G3
5. Standard API 6D
ASME B16.10
N/A Page 489 of 842

N/A
N/A
N/A
Valve Code VDE-1500-2-S21F
Specs G3
4. Ball Mouting N/A
5. Standard API 6D
ASME B16.10

Specs G3
5. Standard API 6D
11. Body Material ASTM A182 Gr F316 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
ASME B16.10
N/A Page 490 of 842

N/A
N/A
N/A
Specs G3
5. Standard API 6D
ASME B16.10

Specs G3
4. Ball Mouting N/A
5. Standard API 6D
ASME B16.10
N/A Page 491 of 842

N/A
N/A
N/A
Specs G3
5. Standard API 6D
14. Seat Insert N/A
ASME B16.10

Specs G3
5. Standard API 6D
14. Seat Insert N/A
ASME B16.10
N/A Page 492 of 842

N/A
N/A
N/A
Valve Code VDE-1500-2-S2F1
Specs G3

Specs G3
N/A Page 493 of 842

N/A
N/A
N/A
Specs G3

Specs G3
N/A Page 494 of 842

N/A
N/A
N/A
Specs G3

Specs G3
N/A Page 495 of 842

N/A
N/A
N/A
Specs B11 B26
7. End Connection Flanged ASME B16.5, RF
20. Seat Type N/A
Valve Code VDE-150-2-C101

Specs B9 B10
20. Seat Type N/A
N/A Page 496 of 842

N/A
N/A
N/A
Specs B10
7. End Connection Flanged ASME B16.5, RF x NPT 1/2" ASME B1.20.1
20. Seat Type N/A

Specs B10
20. Seat Type N/A
N/A Page 497 of 842

N/A
N/A
N/A
Specs B10
20. Seat Type N/A

Specs B10
17. Stem Seal Material Group F (acc. item A.7.1.5.6)
20. Seat Type N/A
N/A Page 498 of 842

N/A
N/A
N/A
Specs B10
20. Seat Type N/A

Specs B10
5. Standard API 6D
18. Operator Type 3" Lever
4" - 8" Gearbox
ASME B16.10
N/A Page 499 of 842

N/A
N/A
N/A
Specs B10
5. Standard API 6D
4" - 8" Gearbox
ASME B16.10
Valve Code VDE-150-2-C11F

Specs B9 B10 B17
5. Standard API 6D
4" - 8" Gearbox
ASME B16.10
N/A Page 500 of 842

N/A
N/A
N/A
Valve Code VDE-150-2-C1F1
Specs B9 B10 B17
20. Seat Type N/A

Specs B9 B10 B17
20. Seat Type N/A
N/A Page 501 of 842

N/A
N/A
N/A
Specs B9 B10 B17
20. Seat Type N/A

Specs B9 B10 B17
20. Seat Type N/A
N/A Page 502 of 842

N/A
N/A
N/A
Specs B9 B10 B17
20. Seat Type N/A

Specs B9 B10 B17
20. Seat Type N/A
N/A Page 503 of 842

N/A
N/A
N/A
Specs B6 B19
20. Seat Type N/A

Specs B6 B19
20. Seat Type N/A
N/A Page 504 of 842

N/A
N/A
N/A
Specs B6 B19
20. Seat Type N/A

Specs B6 B19
20. Seat Type N/A
N/A Page 505 of 842

N/A
N/A
N/A
Specs B6 B19
20. Seat Type N/A

Specs B6 B19
20. Seat Type N/A
N/A Page 506 of 842

N/A
N/A
N/A
Specs B6 B19
20. Seat Type N/A

Specs B6 B19
20. Seat Type N/A
N/A Page 507 of 842

N/A
N/A
N/A
Specs B6 B19
5. Standard API 6D
11. Body Material ASTM A350 Gr LF2 CL1 or ASTM A352 Gr LCC + SS316 weld overlay (acc. item
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs B6 B19
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 508 of 842

N/A
N/A
N/A
Specs B6
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs B6 B19
20. Seat Type N/A
N/A Page 509 of 842

N/A
N/A
N/A
Specs B6 B19
20. Seat Type N/A

Specs B6 B19
20. Seat Type N/A
N/A Page 510 of 842

N/A
N/A
N/A
Specs B6 B19
20. Seat Type N/A

Specs B6 B19
20. Seat Type N/A
N/A Page 511 of 842

N/A
N/A
N/A
Specs B6 B19
20. Seat Type N/A

Specs B6 B19
20. Seat Type N/A
N/A Page 512 of 842

N/A
N/A
N/A
Specs B6 B19
20. Seat Type N/A

Specs B30
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 513 of 842

N/A
N/A
N/A
Specs B30
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs B11 B16
20. Seat Type N/A
N/A Page 514 of 842

N/A
N/A
N/A
Specs B11 B16
20. Seat Type N/A

Specs B11 B16
20. Seat Type N/A
N/A Page 515 of 842

N/A
N/A
N/A
Specs B11 B16
20. Seat Type N/A

Specs B11 B16
20. Seat Type N/A
N/A Page 516 of 842

N/A
N/A
N/A
Specs B11 B16
20. Seat Type N/A

Specs B11 B16
20. Seat Type N/A
N/A Page 517 of 842

N/A
N/A
N/A
Specs B11 B16
20. Seat Type N/A

Specs B12
20. Seat Type N/A
N/A Page 518 of 842

N/A
N/A
N/A
Specs B12
20. Seat Type N/A

Specs B12
20. Seat Type N/A
N/A Page 519 of 842

N/A
N/A
N/A
Specs B12
20. Seat Type N/A

Specs B12
20. Seat Type N/A
N/A Page 520 of 842

N/A
N/A
N/A
Specs B12
20. Seat Type N/A

Specs B12
20. Seat Type N/A
N/A Page 521 of 842

N/A
N/A
N/A
Specs B12
20. Seat Type N/A

Specs B30
20. Seat Type N/A
N/A Page 522 of 842

N/A
N/A
N/A
Specs B30
20. Seat Type N/A

Specs B30
20. Seat Type N/A
N/A Page 523 of 842

N/A
N/A
N/A
Specs B30
20. Seat Type N/A

Specs B30
20. Seat Type N/A
N/A Page 524 of 842

N/A
N/A
N/A
Specs B30
20. Seat Type N/A

Specs B30
20. Seat Type N/A
N/A Page 525 of 842

N/A
N/A
N/A
Specs B30
20. Seat Type N/A

Specs B3
20. Seat Type N/A
N/A Page 526 of 842

N/A
N/A
N/A
Specs B3
20. Seat Type N/A

Specs B3
20. Seat Type N/A
N/A Page 527 of 842

N/A
N/A
N/A
Specs B3
20. Seat Type N/A

Specs B3
20. Seat Type N/A
N/A Page 528 of 842

N/A
N/A
N/A
Specs B3
20. Seat Type N/A

Specs B3
20. Seat Type N/A
N/A Page 529 of 842

N/A
N/A
N/A
Specs B3
20. Seat Type N/A

Specs B3
5. Standard API 6D
11. Body Material ASTM A182 Gr F316 or ASTM A351 Gr CF8M + Inconel 625 weld overlay (acc.
item A.7.1.7.3)
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10
N/A Page 530 of 842

N/A
N/A
N/A
Specs B3
20. Seat Type N/A

Specs B3
20. Seat Type N/A
N/A Page 531 of 842

N/A
N/A
N/A
Specs B3
20. Seat Type N/A

Specs B3
20. Seat Type N/A
N/A Page 532 of 842

N/A
N/A
N/A
Specs B3
20. Seat Type N/A

Specs B3
20. Seat Type N/A
N/A Page 533 of 842

N/A
N/A
N/A
Specs B3
20. Seat Type N/A

Specs B3
20. Seat Type N/A
N/A Page 534 of 842

N/A
N/A
N/A
Specs H6
7. End Connection Compact Flange ISO 27509 IX Ring

Specs H6
7. End Connection Compact Flange ISO 27509 IX x FNPT 1/2" ASME B1.20.1
N/A Page 535 of 842

N/A
N/A
N/A
Specs H6

Specs H6
5. Standard API 6D
11. Body Material ASTM A350 Gr LF2 CL1 + SS316 weld overlay (acc. item A.7.1.7.3)
ASME B16.10
N/A Page 536 of 842

N/A
N/A
N/A
Specs H6
5. Standard API 6D
7. End Connection 3" ASME B16.5, IX
4" - 8" ISO 27509, IX
11. Body Material ASTM A350 Gr LF2 CL1 + SS316 weld overlay (acc. item A.7.1.7.3)
ASME B16.10

Specs H6
5. Standard API 6D
ASME B16.10
N/A Page 537 of 842

N/A
N/A
N/A
Specs H6
5. Standard API 6D
14. Seat Insert N/A
ASME B16.10

Specs H6
N/A Page 538 of 842

N/A
N/A
N/A
Specs H6

Specs H30
5. Standard API 6D
ASME B16.10
N/A Page 539 of 842

N/A
N/A
N/A
Specs H30
5. Standard API 6D
ASME B16.10

Specs H12P H12
N/A Page 540 of 842

N/A
N/A
N/A
Specs H12P

Specs H12P H12
N/A Page 541 of 842

N/A
N/A
N/A
Specs H12P H12

Specs H12P H12
5. Standard API 6D
ASME B16.10
N/A Page 542 of 842

N/A
N/A
N/A
Specs H12P H12
5. Standard API 6D
ASME B16.10

Specs H12P H12
5. Standard API 6D
ASME B16.10
N/A Page 543 of 842

N/A
N/A
N/A
Specs H12P H12
5. Standard API 6D
14. Seat Insert N/A
ASME B16.10

Specs H12P H12
5. Standard API 6D
14. Seat Insert N/A
ASME B16.10
N/A Page 544 of 842

N/A
N/A
N/A
Specs H12P

Specs H12P H12
N/A Page 545 of 842

N/A
N/A
N/A
Specs H12P H12

Specs H12P H12
N/A Page 546 of 842

N/A
N/A
N/A
Specs H30
6. Size Range (NPS) N/A

Specs H30
N/A Page 547 of 842

N/A
N/A
N/A
Specs H30

Specs H30
N/A Page 548 of 842

N/A
N/A
N/A
Specs H30

Specs H3
N/A Page 549 of 842

N/A
N/A
N/A
Specs H3

Specs H3
N/A Page 550 of 842

N/A
N/A
N/A
Specs H3
5. Standard API 6D
ASME B16.10

Specs H3
5. Standard API 6D
ASME B16.10
N/A Page 551 of 842

N/A
N/A
N/A
Specs H3
5. Standard API 6D
14. Seat Insert N/A
ASME B16.10

Specs H3
5. Standard API 6D
14. Seat Insert N/A
ASME B16.10
N/A Page 552 of 842

N/A
N/A
N/A
Specs H3

Specs H3
N/A Page 553 of 842

N/A
N/A
N/A
Specs H3

Specs H12
5. Standard API 6D
14. Seat Insert N/A
ASME B16.10
N/A Page 554 of 842

N/A
N/A
N/A
Valve Code VDE-2510-3-D37G
Specs H12P
5. Standard API 6D
14. Seat Insert N/A
ASME B16.10

Specs C10
20. Seat Type N/A
N/A Page 555 of 842

N/A
N/A
N/A
Specs C10
20. Seat Type N/A

Specs C10
20. Seat Type N/A
N/A Page 556 of 842

N/A
N/A
N/A
Specs C10
20. Seat Type N/A

Specs C10
5. Standard API 6D
4" - 8" Gearbox
ASME B16.10
N/A Page 557 of 842

N/A
N/A
N/A
Specs C10
5. Standard API 6D
4" - 8" Gearbox
ASME B16.10

Specs C10
5. Standard API 6D
4" - 8" Gearbox
ASME B16.10
N/A Page 558 of 842

N/A
N/A
N/A
Specs C10
20. Seat Type N/A

Specs C10
20. Seat Type N/A
N/A Page 559 of 842

N/A
N/A
N/A
Specs C10
20. Seat Type N/A

Specs C10
20. Seat Type N/A
N/A Page 560 of 842

N/A
N/A
N/A
Specs C10
20. Seat Type N/A

Specs C10
20. Seat Type N/A
N/A Page 561 of 842

N/A
N/A
N/A
Specs C6 C19
20. Seat Type N/A

Specs C6 C19
20. Seat Type N/A
N/A Page 562 of 842

N/A
N/A
N/A
Specs C6 C19
20. Seat Type N/A

Specs C6 C19
20. Seat Type N/A
N/A Page 563 of 842

N/A
N/A
N/A
Specs C6 C19
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs C6 C19
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 564 of 842

N/A
N/A
N/A
Specs C6
5. Standard API 6D
A.7.1.7.3)
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10

Specs C6 C19
20. Seat Type N/A
N/A Page 565 of 842

N/A
N/A
N/A
Specs C6 C19
20. Seat Type N/A

Specs C6 C19
20. Seat Type N/A
N/A Page 566 of 842

N/A
N/A
N/A
Specs C6 C19
20. Seat Type N/A

Specs C30
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 567 of 842

N/A
N/A
N/A
Specs C30
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs C30
5. Standard API 6D
A.7.1.7.3)
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10
N/A Page 568 of 842

N/A
N/A
N/A
Specs C16
20. Seat Type N/A

Specs C16
20. Seat Type N/A
N/A Page 569 of 842

N/A
N/A
N/A
Specs C16
20. Seat Type N/A

Specs C16
20. Seat Type N/A
N/A Page 570 of 842

N/A
N/A
N/A
Specs C16
5. Standard API 6D
4" - 8" Gearbox
ASME B16.10

Specs C16
20. Seat Type N/A
N/A Page 571 of 842

N/A
N/A
N/A
Specs C16
20. Seat Type N/A

Specs C16
20. Seat Type N/A
N/A Page 572 of 842

N/A
N/A
N/A
Specs C16
20. Seat Type N/A

Specs C12
20. Seat Type N/A
N/A Page 573 of 842

N/A
N/A
N/A
Specs C12
20. Seat Type N/A

Specs C12
20. Seat Type N/A
N/A Page 574 of 842

N/A
N/A
N/A
Specs C12
20. Seat Type N/A

Specs C12
5. Standard API 6D
4" - 8" Gearbox
ASME B16.10
N/A Page 575 of 842

N/A
N/A
N/A
Specs C12
5. Standard API 6D
4" - 8" Gearbox
ASME B16.10

Specs C12
20. Seat Type N/A
N/A Page 576 of 842

N/A
N/A
N/A
Specs C12
20. Seat Type N/A

Specs C12
20. Seat Type N/A
N/A Page 577 of 842

N/A
N/A
N/A
Specs C12
20. Seat Type N/A

Specs C30
20. Seat Type N/A
N/A Page 578 of 842

N/A
N/A
N/A
Specs C30
20. Seat Type N/A

Specs C30
20. Seat Type N/A
N/A Page 579 of 842

N/A
N/A
N/A
Specs C30
20. Seat Type N/A

Specs C30
20. Seat Type N/A
N/A Page 580 of 842

N/A
N/A
N/A
Specs C30
20. Seat Type N/A

Specs C30
20. Seat Type N/A
N/A Page 581 of 842

N/A
N/A
N/A
Specs C30
20. Seat Type N/A

Specs C3
20. Seat Type N/A
N/A Page 582 of 842

N/A
N/A
N/A
Specs C3
20. Seat Type N/A

Specs C3
20. Seat Type N/A
N/A Page 583 of 842

N/A
N/A
N/A
Specs C3
20. Seat Type N/A

Specs C3
20. Seat Type N/A
N/A Page 584 of 842

N/A
N/A
N/A
Specs C3
20. Seat Type N/A

Specs C3
20. Seat Type N/A
N/A Page 585 of 842

N/A
N/A
N/A
Specs C3
20. Seat Type N/A

Specs C3
5. Standard API 6D
item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 586 of 842

N/A
N/A
N/A
Specs C3
20. Seat Type N/A

Specs C3
20. Seat Type N/A
N/A Page 587 of 842

N/A
N/A
N/A
Specs C3
20. Seat Type N/A

Specs C3
20. Seat Type N/A
N/A Page 588 of 842

N/A
N/A
N/A
Specs C3
20. Seat Type N/A

Specs C3
20. Seat Type N/A
N/A Page 589 of 842

N/A
N/A
N/A
Specs C3
20. Seat Type N/A

Specs C3
20. Seat Type N/A
N/A Page 590 of 842

N/A
N/A
N/A
Valve Code VDE-600-2-A515
Specs E32
5. Standard API 6D
item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
Valve Code VDE-600-2-A51F

Specs E32
5. Standard API 6D
item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 591 of 842

N/A
N/A
N/A
Specs E32
5. Standard API 6D
item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs E32
5. Standard API 6D
item A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10
N/A Page 592 of 842

N/A
N/A
N/A
Specs E32
5. Standard API 6D
item A.7.1.7.3)
carbide coating
carbide coating
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10

Specs E32
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10
N/A Page 593 of 842

N/A
N/A
N/A
Specs E32
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10

Specs E6 E19
20. Seat Type N/A
N/A Page 594 of 842

N/A
N/A
N/A
Specs E6 E19
20. Seat Type N/A

Specs E6 E19
20. Seat Type N/A
N/A Page 595 of 842

N/A
N/A
N/A
Specs E6 E19
20. Seat Type N/A

Specs E6 E19
20. Seat Type N/A
N/A Page 596 of 842

N/A
N/A
N/A
Specs E6 E19
20. Seat Type N/A

Specs E6 E19
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 597 of 842

N/A
N/A
N/A
Specs E6 E19
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs E6 E19
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 598 of 842

N/A
N/A
N/A
Specs E6 E19
5. Standard API 6D
item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs E6 E19
5. Standard API 6D
item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 599 of 842

N/A
N/A
N/A
Specs E6 E19
5. Standard API 6D
item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs E19
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10
N/A Page 600 of 842

N/A
N/A
N/A
Specs E19
5. Standard API 6D
item A.7.1.7.3)
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10

Specs E6 E19
20. Seat Type N/A
N/A Page 601 of 842

N/A
N/A
N/A
Specs E6 E19
20. Seat Type N/A

Specs E6 E19
20. Seat Type N/A
N/A Page 602 of 842

N/A
N/A
N/A
Specs E6 E19
20. Seat Type N/A

Specs E6 E19
20. Seat Type N/A
N/A Page 603 of 842

N/A
N/A
N/A
Specs E6 E19
20. Seat Type N/A

Specs E19
13. Seat Material ASTM A105 + Hard Coating (acc. Item A.7.1.7.4)
20. Seat Type N/A
25. Notes Acceptance criteria for sealing tests see Annex A.
N/A Page 604 of 842

N/A
N/A
N/A
Specs E19
13. Seat Material ASTM A105 + Hard Coating (acc. Item A.7.1.7.4)
20. Seat Type N/A
25. Notes Acceptance criteria for sealing tests see Annex A.

Specs E30
5. Standard API 6D
A.7.1.7.3)
12. Obturator Material AISI 316 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
13. Seat Material AISI 316 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 605 of 842

N/A
N/A
N/A
Specs E30
5. Standard API 6D
A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs E30
5. Standard API 6D
A.7.1.7.3)
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10
N/A Page 606 of 842

N/A
N/A
N/A
Specs E16
20. Seat Type N/A

Specs E16
20. Seat Type N/A
N/A Page 607 of 842

N/A
N/A
N/A
Specs E16
20. Seat Type N/A

Specs E16
20. Seat Type N/A
N/A Page 608 of 842

N/A
N/A
N/A
Specs E16
5. Standard API 6D
4" - 8" Gearbox
ASME B16.10

Specs E16
4" - 8" Gearbox
ASME B16.10
N/A Page 609 of 842

N/A
N/A
N/A
Specs E16
4" - 8" Gearbox
ASME B16.10

Specs E16
4" - 8" Gearbox
ASME B16.10
N/A Page 610 of 842

N/A
N/A
N/A
Specs E16
4" - 8" Gearbox
ASME B16.10

Specs E16
4" - 8" Gearbox
ASME B16.10
N/A Page 611 of 842

N/A
N/A
N/A
Specs E16
4" - 8" Gearbox
ASME B16.10

Specs E16
4" - 8" Gearbox
ASME B16.10
N/A Page 612 of 842

N/A
N/A
N/A
Specs E16
4" - 8" Gearbox
ASME B16.10

Specs E16
20. Seat Type N/A
N/A Page 613 of 842

N/A
N/A
N/A
Specs E16
20. Seat Type N/A

Specs E16
20. Seat Type N/A
N/A Page 614 of 842

N/A
N/A
N/A
Specs E16
20. Seat Type N/A

Specs E30
20. Seat Type N/A
N/A Page 615 of 842

N/A
N/A
N/A
Specs E32
20. Seat Type N/A

Specs E32
20. Seat Type N/A
N/A Page 616 of 842

N/A
N/A
N/A
Specs E30 E32
20. Seat Type N/A

Specs E30 E32
20. Seat Type N/A
N/A Page 617 of 842

N/A
N/A
N/A
Specs E30 E32
13. Seat Material PEEK + Hard Coating (acc. Item A.7.1.7.4)
20. Seat Type N/A

Specs E32
13. Seat Material PEEK + Hard Coating (acc. Item A.7.1.7.4)
20. Seat Type N/A
N/A Page 618 of 842

N/A
N/A
N/A
Specs E30 E32
20. Seat Type N/A

Specs E30 E32
20. Seat Type N/A
N/A Page 619 of 842

N/A
N/A
N/A
Specs E30 E32
20. Seat Type N/A

Specs E30 E32
20. Seat Type N/A
N/A Page 620 of 842

N/A
N/A
N/A
Specs E3
20. Seat Type N/A

Specs E3
20. Seat Type N/A
N/A Page 621 of 842

N/A
N/A
N/A
Specs E3
20. Seat Type N/A

Specs E3
20. Seat Type N/A
N/A Page 622 of 842

N/A
N/A
N/A
Specs E3
20. Seat Type N/A

Specs E3
20. Seat Type N/A
N/A Page 623 of 842

N/A
N/A
N/A
Specs E3
4" - 8" Gearbox
ASME B16.10

Specs E3
4" - 8" Gearbox
ASME B16.10
N/A Page 624 of 842

N/A
N/A
N/A
Specs E3
4" - 8" Gearbox
ASME B16.10

Specs E3
4" - 8" Gearbox
ASME B16.10
N/A Page 625 of 842

N/A
N/A
N/A
Specs E3
4" - 8" Gearbox
ASME B16.10

Specs E3
4" - 8" Gearbox
ASME B16.10
N/A Page 626 of 842

N/A
N/A
N/A
Specs E3
4" - 8" Gearbox
ASME B16.10

Specs E3
4" - 8" Gearbox
ASME B16.10
N/A Page 627 of 842

N/A
N/A
N/A
Specs E3
4" - 8" Gearbox
ASME B16.10

Specs E3
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10
N/A Page 628 of 842

N/A
N/A
N/A
Specs E3
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10

Specs E3
20. Seat Type N/A
N/A Page 629 of 842

N/A
N/A
N/A
Specs E3
20. Seat Type N/A

Specs E3
20. Seat Type N/A
N/A Page 630 of 842

N/A
N/A
N/A
Specs E3
20. Seat Type N/A

Specs E3
20. Seat Type N/A
N/A Page 631 of 842

N/A
N/A
N/A
Specs E3
20. Seat Type N/A

Specs F3
20. Seat Type N/A
N/A Page 632 of 842

N/A
N/A
N/A
Specs F3
20. Seat Type N/A

Specs F3
20. Seat Type N/A
N/A Page 633 of 842

N/A
N/A
N/A
Specs F3
20. Seat Type N/A

Specs F3
20. Seat Type N/A
N/A Page 634 of 842

N/A
N/A
N/A
Specs F3
20. Seat Type N/A

Specs F3
4" - 8" Gearbox
ASME B16.10
N/A Page 635 of 842

N/A
N/A
N/A
Specs F3
4" - 8" Gearbox
ASME B16.10

Specs F3
4" - 8" Gearbox
ASME B16.10
N/A Page 636 of 842

N/A
N/A
N/A
Specs F3
item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs F3
item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10
N/A Page 637 of 842

N/A
N/A
N/A
Specs F3
item A.7.1.7.3)
4" - 8" Gearbox
ASME B16.10

Specs F3
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10
N/A Page 638 of 842

N/A
N/A
N/A
Specs F3
14. Seat Insert N/A
4" - 8" Gearbox
ASME B16.10

Specs F3
20. Seat Type N/A
N/A Page 639 of 842

N/A
N/A
N/A
Specs F3
20. Seat Type N/A

Specs F3
20. Seat Type N/A
N/A Page 640 of 842

N/A
N/A
N/A
Specs F3
20. Seat Type N/A

Specs F3
20. Seat Type N/A
N/A Page 641 of 842

N/A
N/A
N/A
Specs F3
20. Seat Type N/A

Specs F3
20. Seat Type N/A
N/A Page 642 of 842

N/A
N/A
N/A
Specs F3
20. Seat Type N/A
N/A Page 643 of 842

N/A
N/A
N/A
A.12.4 GATE VALVES
Valve Code VGA-10000-2-D31F
Specs J12P J12
1. Valve Type Gate
4. Obturator Type Slab
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"
7. End Connection API 6A, studded type 6BX (stud and nuts included)
12. TRIM Material N/A
13. Gate Material ASTM A182 Gr F55 + Tungsten Carbide (acc. item A.8.2.2.3)
14. Seat Material ASTM A182 Gr F55 + Tungsten Carbide (acc. item A.8.2.2.3)
17. Stem Seal Material According manufacturer standard, fitted to service conditions
18. Seat Seal Material PEEK+UNS R30003 (Elgiloy)
20. Additional Requirement Fire tested acc. API 6FA; Fugitive Emission (acc. item A.6.1.6)
21. Body Construction According manufacturer standard
24. Stem Design Non rising stem
Valve Code VGA-10000-2-N111

Specs J40
1. Valve Type Gate
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"
13. Gate Material ASTM B564 (UNS N06625) + Tungsten Carbide (acc. item A.8.2.2.3)
14. Seat Material ASTM B564 (UNS N06625) + Tungsten Carbide (acc. item A.8.2.2.3)
20. Additional Requirement Fire tested acc. API 6FA
N/A Page 644 of 842

N/A
N/A
N/A
Valve Code VGA-10000-2-N11F
Specs J40
1. Valve Type Gate
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"
Valve Code VGA-10000-3-D311

Specs J12P J12
1. Valve Type Gate
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"
N/A Page 645 of 842

N/A
N/A
N/A
Specs J12P J12
1. Valve Type Gate
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"

Specs J40
1. Valve Type Gate
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"
N/A Page 646 of 842

N/A
N/A
N/A
Valve Code VGA-10000-3-N11F
Specs J40
1. Valve Type Gate
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"

Specs J12P J12
1. Valve Type Gate
5. Standard API 6A
6. Size Range (NPS) 1 ½" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"
N/A Page 647 of 842

N/A
N/A
N/A
Specs J12P J12
1. Valve Type Gate
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"
N/A Page 648 of 842

N/A
N/A
N/A
Valve Code VGA-1500-1-S231
Specs G3
1. Valve Type Gate
4. Obturator Type Flexible Wedge, one piece
5. Standard API 600 / IOGP S-611
12. TRIM Material TRIM 16 according API
13. Gate Material ASTM A182 Gr F316
14. Seat Material Stellite (Co-Cr Alloy acc. item A.8.2.1.2)
17. Stem Seal Material Flexible graphite with inconel wire
18. Seat Seal Material N/A
19. Operator Type 2" non rising handwheel
3" - 16" Gearbox
20. Additional Requirement Fire safe design (acc. item A.6.1.5)
21. Body Construction bolted bonnet
24. Stem Design Rising Stem OS&Y

Specs G3
1. Valve Type Gate
19. Operator Type 2" non rising handwheel
3" - 16" Gearbox
N/A Page 649 of 842

N/A
N/A
N/A
Specs F3 G3
1. Valve Type Gate
4. Obturator Type Solid Wedge
5. Standard API 602
7. End Connection socket weld ends ASME B16.11
13. Gate Material ASTM A182 Gr F316L
19. Operator Type non rising handwheel
Valve Code VGA-150-1-C131

Specs B4 B9 B10 B17
1. Valve Type Gate
11. Body Material ASTM A105 or ASTM A216 Gr WCB
13. Gate Material AISI 410
19. Operator Type 2" - 10" non rising handwheel
12" - 36" Gearbox
N/A Page 650 of 842

N/A
N/A
N/A
Specs B4
1. Valve Type Gate
13. Gate Material Stellite (Co-Cr Alloy acc. Item A.8.2.1.2)
12" - 36" Gearbox

Specs B11 B16 B26
1. Valve Type Gate
13. Gate Material (A182 F51 or A995 4A) + E/ERCoCr
12" - 36" Gearbox
N/A Page 651 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Gate
12" - 36" Gearbox

Specs B3
1. Valve Type Gate
12" - 36" Gearbox
N/A Page 652 of 842

N/A
N/A
N/A
Valve Code VGA-150-1-U331
Specs B7
1. Valve Type Gate
4. Obturator Type Flexible Wedge (NPS>=2), one piece
5. Standard API 600
13. Gate Material ASTM B148 (UNS C95800)
16. Stem Material ASTM B150 (UNS C63200)
17. Stem Seal Material PTFE
12" - 24" Gearbox

Specs B14 B22 B23
1. Valve Type Gate
5. Standard API 600
12" - 24" Gearbox
N/A Page 653 of 842

N/A
N/A
N/A
Specs B4 B9 B10 B17
1. Valve Type Gate
12" - 36" Gearbox

Specs B4
1. Valve Type Gate
12" - 36" Gearbox
N/A Page 654 of 842

N/A
N/A
N/A
Specs B11 B16 B26
1. Valve Type Gate
12" - 36" Gearbox

Specs B3
1. Valve Type Gate
12" - 36" Gearbox
N/A Page 655 of 842

N/A
N/A
N/A
Specs B7
1. Valve Type Gate
5. Standard API 600
12" - 24" Gearbox

Specs B14 B22 B23
1. Valve Type Gate
5. Standard API 600
12" - 24" Gearbox
N/A Page 656 of 842

N/A
N/A
N/A
Specs H12P H12
1. Valve Type Gate
5. Standard API 600
7. End Connection butt weld ASME B16.25
14. Seat Material ASTM A182 Gr F55

Specs C4 C10
1. Valve Type Gate
10" - 36" Gearbox
N/A Page 657 of 842

N/A
N/A
N/A
Specs C4
1. Valve Type Gate
10" - 36" Gearbox

Specs C11 C16
1. Valve Type Gate
10" - 36" Gearbox
N/A Page 658 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Gate
10" - 36" Gearbox

Specs C3
1. Valve Type Gate
10" - 36" Gearbox
N/A Page 659 of 842

N/A
N/A
N/A
Specs C23
1. Valve Type Gate
5. Standard API 600
12" - 24" Gearbox

Specs C4 C10
1. Valve Type Gate
10" - 36" Gearbox
N/A Page 660 of 842

N/A
N/A
N/A
Specs C4
1. Valve Type Gate
10" - 36" Gearbox

Specs C11 C16
1. Valve Type Gate
10" - 36" Gearbox
N/A Page 661 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Gate
6" - 16" Gearbox

Specs E3
1. Valve Type Gate
6" - 16" Gearbox
N/A Page 662 of 842

N/A
N/A
N/A
Specs B4 B9 B10 B17 C10
1. Valve Type Gate
5. Standard API 602

Specs B4 C4
1. Valve Type Gate
5. Standard API 602
N/A Page 663 of 842

N/A
N/A
N/A
Specs B16 C16 E16
1. Valve Type Gate
5. Standard API 602
13. Gate Material Duplex (UNS S31803)

Specs B12 C12
1. Valve Type Gate
5. Standard API 602
13. Gate Material Super Duplex (UNS S32760)
N/A Page 664 of 842

N/A
N/A
N/A
Specs B3 C3 E3
1. Valve Type Gate
5. Standard API 602
13. Gate Material AISI 316L

Specs B4 C4
1. Valve Type Gate
5. Standard API 602
N/A Page 665 of 842

N/A
N/A
N/A
Specs B19
1. Valve Type Gate
5. Standard API 602

Specs B30
1. Valve Type Gate
5. Standard API 602
13. Gate Material ASTM B564 (UNS N06625)
N/A Page 666 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Gate
4" - 18" Gearbox
N/A Page 667 of 842

N/A
N/A
N/A
A.12.5 GLOBE VALVES
Valve Code VGL-10000-2-D301

Specs J12
1. Valve Type Globe
4. Obturator Type Bevelled Disc
5. Standard API 6A
13. Obturator Material ASTM A182 Gr F55
16. Seat-Stem Seal Material According manufacturer standard, fitted to service conditions
18. Stem Construction outside screw stem
19. Bonnet Construction According manufacturer standard
20. Product testing FAT according A.9.3
21. Coating or Cladding N/A
22. Notes N/A
Valve Code VGL-10000-2-D3F1

Specs J12P J12
1. Valve Type Globe
5. Standard API 6A
22. Notes N/A
23. Additional Requirement Fugitive Emission (acc. item A.6.1.6)
N/A Page 668 of 842

N/A
N/A
N/A
Valve Code VGL-10000-2-N101
Specs J40
1. Valve Type Globe
5. Standard API 6A
22. Notes N/A
Valve Code VGL-10000-2-N1F1

Specs J40
1. Valve Type Globe
5. Standard API 6A
22. Notes N/A
N/A Page 669 of 842

N/A
N/A
N/A
Valve Code VGL-1500-2-S201
Specs G3
1. Valve Type Globe
5. Standard BS 1873
15. Stem Material ASTM A564 Type 630 H1150 (UNS S17400)
16. Seat-Stem Seal Material Flexible graphite with inconel wire
17. Operator Type 2" Rising Handwheel
3" - 14" Gearbox
19. Bonnet Construction bolted bonnet
22. Notes N/A

Specs G3
1. Valve Type Globe
5. Standard BS 1873
12. TRIM Material N/A (Low Temperature Stem)
3" - 14" Gearbox
22. Notes N/A
N/A Page 670 of 842

N/A
N/A
N/A
Valve Code VGL-1500-2-S2F1
Specs G3
1. Valve Type Globe
5. Standard BS 1873
3" - 14" Gearbox
22. Notes N/A

Specs G3
1. Valve Type Globe
5. Standard BS 1873
3" - 14" Gearbox
22. Notes N/A
N/A Page 671 of 842

N/A
N/A
N/A
Valve Code VGL-150-1-C101
Specs B9 B10 B17
1. Valve Type Globe
5. Standard BS 1873
12. TRIM Material TRIM CR 13 and HF according BS 1873
17. Operator Type 2" - 6" Rising Handwheel
8" - 20" Gearbox
22. Notes N/A
23. Additional Requirements N/A

Specs B4
1. Valve Type Globe
5. Standard BS 1873
12. TRIM Material TRIM HF according BS 1873
13. Obturator Material Stellite (Co-Cr Alloy acc. item A.8.2.1.2)
8" - 18" Gearbox
22. Notes N/A
N/A Page 672 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Globe
5. Standard BS 1873
11. Body Material ASTM A350 Gr LF2 CL1 or ASTM A352 Gr LCC
8" - 18" Gearbox
22. Notes N/A

Specs B11 B16 B26
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 673 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs B3
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 674 of 842

N/A
N/A
N/A
Valve Code VGL-150-1-U301
Specs B7
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs B14 B22 B23
1. Valve Type Globe
5. Standard BS 1873
8" - 48" Gearbox
22. Notes N/A
N/A Page 675 of 842

N/A
N/A
N/A
Specs B14 B23
1. Valve Type Globe
5. Standard MSS SP-80
17. Operator Type Rising Handwheel
19. Bonnet Construction unnion bonnet
22. Notes N/A

Specs B9 B10 B17
1. Valve Type Globe
5. Standard BS 1873
8" - 20" Gearbox
22. Notes N/A
N/A Page 676 of 842

N/A
N/A
N/A
Specs B4
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
Valve Code VGL-150-2-C1F1

Specs B9 B10 B17
1. Valve Type Globe
5. Standard BS 1873
8" - 20" Gearbox
22. Notes N/A
23. Additional Requirements Fugitive Emission (acc. item A.6.1.6)
N/A Page 677 of 842

N/A
N/A
N/A
Specs B9 B10 B17
1. Valve Type Globe
5. Standard BS 1873
8" - 20" Gearbox
22. Notes N/A

Specs B6 B19
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 678 of 842

N/A
N/A
N/A
Specs B6 B19
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs B30
1. Valve Type Globe
5. Standard BS 1873
A.7.1.7.3)
8" - 20" Gearbox
21. Coating or Cladding Full clad - Inconel 625 weld overlay on all wetted parts
22. Notes N/A
N/A Page 679 of 842

N/A
N/A
N/A
Specs B30
1. Valve Type Globe
5. Standard BS 1873
A.7.1.7.3)
8" - 18" Gearbox
22. Notes N/A

Specs B11 B26
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 680 of 842

N/A
N/A
N/A
Specs B11 B16 B26
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs B11 B16
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 681 of 842

N/A
N/A
N/A
Specs B12
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs B3
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 682 of 842

N/A
N/A
N/A
Specs B3
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs B7
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 683 of 842

N/A
N/A
N/A
Specs B14 B22 B23
1. Valve Type Globe
5. Standard BS 1873
8" - 24" Gearbox
22. Notes N/A

Specs H6
1. Valve Type Globe
5. Standard BS 1873
3" - 16" Gearbox
22. Notes N/A
N/A Page 684 of 842

N/A
N/A
N/A
Specs H6
1. Valve Type Globe
5. Standard BS 1873
3" - 16" Gearbox
22. Notes N/A

Specs H30
1. Valve Type Globe
5. Standard BS 1873
3" - 16" Gearbox
22. Notes N/A
N/A Page 685 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Globe
5. Standard BS 1873
3" - 16" Gearbox
22. Notes N/A

Specs H12
1. Valve Type Globe
5. Standard BS 1873
3" - 16" Gearbox
22. Notes N/A
N/A Page 686 of 842

N/A
N/A
N/A
Specs H12
1. Valve Type Globe
5. Standard BS 1873
3" - 16" Gearbox
22. Notes N/A

Specs H3
1. Valve Type Globe
5. Standard BS 1873
3" - 12" Gearbox
22. Notes N/A
N/A Page 687 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Globe
5. Standard BS 1873
3" - 12" Gearbox
22. Notes N/A

Specs H3
1. Valve Type Globe
5. Standard BS 1873
3" - 14" Gearbox
22. Notes N/A
N/A Page 688 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Globe
5. Standard BS 1873
3" - 14" Gearbox
22. Notes N/A

Specs C10
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 689 of 842

N/A
N/A
N/A
Specs C4
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs C6 C19
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 690 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Globe
5. Standard BS 1873
A.7.1.7.3)
8" - 20" Gearbox
22. Notes N/A

Specs C11 C16
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 691 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs C23
1. Valve Type Globe
5. Standard BS 1873
8" - 12" Gearbox
22. Notes N/A
N/A Page 692 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs C4
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 693 of 842

N/A
N/A
N/A
Specs C10
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs C10
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 694 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs C6 C19
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 695 of 842

N/A
N/A
N/A
Specs C30
1. Valve Type Globe
5. Standard BS 1873
A.7.1.7.3)
8" - 20" Gearbox
22. Notes N/A

Specs C30
1. Valve Type Globe
5. Standard BS 1873
A.7.1.7.3)
8" - 18" Gearbox
22. Notes N/A
N/A Page 696 of 842

N/A
N/A
N/A
Specs C11
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs C11 C16
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 697 of 842

N/A
N/A
N/A
Specs C16
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs C12
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 698 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs C3
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A
N/A Page 699 of 842

N/A
N/A
N/A
Specs C3
1. Valve Type Globe
5. Standard BS 1873
8" - 18" Gearbox
22. Notes N/A

Specs E6 E19
1. Valve Type Globe
5. Standard BS 1873
4" - 20" Gearbox
22. Notes N/A
N/A Page 700 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Globe
5. Standard BS 1873
4" Gearbox
22. Notes N/A

Specs E3
1. Valve Type Globe
5. Standard API 623
12. TRIM Material 316 and Hardfaced
4" Gearbox
22. Notes N/A
N/A Page 701 of 842

N/A
N/A
N/A
Valve Code VGL-600-2-A501
Specs E32
1. Valve Type Globe
5. Standard BS 1873
item A.7.1.7.3)
4" - 14" Gearbox
22. Notes N/A
Valve Code VGL-600-2-A5F1

Specs E32
1. Valve Type Globe
5. Standard BS 1873
item A.7.1.7.3)
4" - 14" Gearbox
22. Notes N/A
N/A Page 702 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Globe
5. Standard BS 1873
4" - 20" Gearbox
22. Notes N/A

Specs E6 E19
1. Valve Type Globe
5. Standard BS 1873
4" - 20" Gearbox
22. Notes N/A
N/A Page 703 of 842

N/A
N/A
N/A
Specs E30
1. Valve Type Globe
5. Standard BS 1873
A.7.1.7.3)
4" - 12" Gearbox
22. Notes N/A

Specs E30
1. Valve Type Globe
5. Standard BS 1873
A.7.1.7.3)
4" - 12" Gearbox
22. Notes N/A
N/A Page 704 of 842

N/A
N/A
N/A
Specs E16
1. Valve Type Globe
5. Standard BS 1873
4" - 12" Gearbox
22. Notes N/A

Specs E16
1. Valve Type Globe
5. Standard BS 1873
4" - 12" Gearbox
22. Notes N/A
N/A Page 705 of 842

N/A
N/A
N/A
Specs E3
1. Valve Type Globe
5. Standard API 623
4" - 18" Gearbox
22. Notes N/A

Specs E3
1. Valve Type Globe
5. Standard API 623
4" - 18" Gearbox
22. Notes N/A
N/A Page 706 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Globe
5. Standard BS 1873
4" Gearbox
22. Notes N/A

Specs F3
1. Valve Type Globe
5. Standard BS 1873
4" - 14" Gearbox
22. Notes N/A
N/A Page 707 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Globe
5. Standard BS 1873
4" - 14" Gearbox
22. Notes N/A
N/A Page 708 of 842

N/A
N/A
N/A
A.12.6 CHECK VALVES
Valve Code VRE-10000-2-D325
Specs J12P J12
1. Valve Type Check
4. Obturator Type Swing
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"
16. Shaft Material ASTM A276 (UNS S32760)
18. Cover Construction bolted cover
21. Notes N/A

Specs J12P J12
1. Valve Type Check
4. Obturator Type Axial non-slam
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"
18. Cover Construction Not Applicable
21. Notes N/A
N/A Page 709 of 842

N/A
N/A
N/A
Valve Code VRE-10000-2-N125
Specs J40
1. Valve Type Check
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" - 14" 9"
16. Shaft Material ASTM B637 (UNS N07718)
21. Notes N/A

Specs J40
1. Valve Type Check
5. Standard API 6A
6. Size Range (NPS) 1" - 2" 1 ¹³/₁₆"
3" 2 ¹/₁₆"
4" 2 ⁹/₁₆"
6" 4 ¹/₁₆"
8" 5 ⅛"
10" 7 ¹/₁₆"
12" 9"
21. Notes N/A
N/A Page 710 of 842

N/A
N/A
N/A
Valve Code VRE-1500-1-S202
Specs F3 G3
1. Valve Type Check
4. Obturator Type Piston
5. Standard API 602
13. Obturator Material AISI 316L
16. Shaft Material Not Applicable
17. Operator Type N/A
21. Notes N/A

Specs F3 G3
1. Valve Type Check
5. Standard API 602
21. Notes N/A
N/A Page 711 of 842

N/A
N/A
N/A
Specs G3
1. Valve Type Check, Wafer type
4. Obturator Type Dual Plate
5. Standard API 594
12. TRIM Material TRIM 12 according API 594
21. Notes Wafer valves shall not to be used with flamable services.

Specs G3
1. Valve Type Check, Flanged type
5. Standard API 594
21. Notes N/A
N/A Page 712 of 842

N/A
N/A
N/A
Specs G3
5. Standard API 6D
21. Notes N/A
Valve Code VRE-150-1-C111

Specs B9 B10 B17
5. Standard API 594
14. Seat Material Group A (acc. item A.7.3.3.1)
N/A Page 713 of 842

N/A
N/A
N/A
Specs B10
5. Standard API 594

Specs B4
5. Standard API 594
N/A Page 714 of 842

N/A
N/A
N/A
Specs B6 B19
5. Standard API 594

Specs B26
5. Standard API 594
21. Notes Material suitable only for onshore application. Through holes drilled and
tapped according to ASME B1.1.
N/A Page 715 of 842

N/A
N/A
N/A
Specs B11 B26
5. Standard API 594

Specs B11
1. Valve Type Check
5. Standard API 602
7. End Connection N/A
21. Notes N/A
N/A Page 716 of 842

N/A
N/A
N/A
Specs B11 B16
5. Standard API 594

Specs B11 B26
5. Standard API 594
N/A Page 717 of 842

N/A
N/A
N/A
Specs B3
5. Standard API 594

Specs B3
5. Standard API 594
N/A Page 718 of 842

N/A
N/A
N/A
Valve Code VRE-150-1-U305
Specs B14 B23
1. Valve Type Check
5. Standard API 602
21. Notes N/A

Specs B7
5. Standard API 594
16. Shaft Material ASTM B150 (UNS C63200)
N/A Page 719 of 842

N/A
N/A
N/A
Specs B7 B23
5. Standard API 594

Specs B14 B22 B23
5. Standard API 594
N/A Page 720 of 842

N/A
N/A
N/A
Specs B9 B10 B17
5. Standard API 594

Specs B4
5. Standard API 594
N/A Page 721 of 842

N/A
N/A
N/A
Specs B9 B10 B17
5. Standard API 594
21. Notes N/A

Specs B9 B10 B17
5. Standard API 6D
21. Notes N/A
N/A Page 722 of 842

N/A
N/A
N/A
Specs B6 B19
5. Standard API 594

Specs B6 B19
5. Standard API 594
21. Notes N/A
N/A Page 723 of 842

N/A
N/A
N/A
Specs B6 B19
5. Standard API 6D
21. Notes N/A

Specs B30
5. Standard API 594
A.7.1.7.3)
21. Notes N/A
N/A Page 724 of 842

N/A
N/A
N/A
Specs B30
5. Standard API 6D
A.7.1.7.3)
21. Notes N/A

Specs B11 B16
5. Standard API 594
N/A Page 725 of 842

N/A
N/A
N/A
Specs B11 B16
5. Standard API 594
21. Notes N/A

Specs B11 B16 B26
5. Standard API 6D
21. Notes N/A
N/A Page 726 of 842

N/A
N/A
N/A
Specs B14 B23
1. Valve Type Check
5. Standard API 602
21. Notes N/A

Specs B12
5. Standard API 594
21. Notes N/A
N/A Page 727 of 842

N/A
N/A
N/A
Specs B12
5. Standard API 6D
21. Notes N/A

Specs B30
1. Valve Type Check
5. Standard API 6D
21. Notes N/A
N/A Page 728 of 842

N/A
N/A
N/A
Specs B3
5. Standard API 594

Specs B3
5. Standard API 594
21. Notes N/A
N/A Page 729 of 842

N/A
N/A
N/A
Specs B3
5. Standard API 6D
21. Notes N/A

Specs B14 B23
5. Standard API 6D
21. Notes N/A
N/A Page 730 of 842

N/A
N/A
N/A
Specs B14 B27
4. Obturator Type Manufacturer Standard
5. Standard Manufacturer Standard
11. Body Material ASTM A395 60-40-18 + PFA liner
13. Obturator Material PFA
14. Seat Material PFA
15. Spring Material According manufacturer standard, fitted to service conditions
19. Product testing FAT according manufacturer standard
21. Notes N/A

Specs B7
1. Valve Type Check
7. End Connection Screwed ends ASME B1.20.1 NPT
8. Pressure Class max. press 200 psig
12. TRIM Material TRIM AA according API 594
19. Cover Construction screwed cover
21. Notes N/A
N/A Page 731 of 842

N/A
N/A
N/A
Specs H30
1. Valve Type Check
21. Notes N/A

Specs H12
1. Valve Type Check
21. Notes N/A
N/A Page 732 of 842

N/A
N/A
N/A
Specs H3
1. Valve Type Check
21. Notes N/A

Specs H6
5. Standard API 594
N/A Page 733 of 842

N/A
N/A
N/A
Specs H6
5. Standard API 594
21. Notes N/A

Specs H6
5. Standard API 6D
21. Notes N/A
N/A Page 734 of 842

N/A
N/A
N/A
Specs H30
5. Standard API 594
21. Notes N/A

Specs H30
5. Standard API 594
21. Notes N/A
N/A Page 735 of 842

N/A
N/A
N/A
Specs H30
5. Standard API 6D
21. Notes N/A

Specs H12
5. Standard API 594
21. Notes N/A
N/A Page 736 of 842

N/A
N/A
N/A
Specs H12
5. Standard API 6D
21. Notes N/A

Specs H3
5. Standard API 594
N/A Page 737 of 842

N/A
N/A
N/A
Specs H3
5. Standard API 594
21. Notes N/A

Specs H3
5. Standard API 6D
21. Notes N/A
N/A Page 738 of 842

N/A
N/A
N/A
Specs C10
5. Standard API 594

Specs C10
5. Standard API 594
N/A Page 739 of 842

N/A
N/A
N/A
Specs C6 C19
5. Standard API 594

Specs C30
5. Standard API 594
A.7.1.7.3)
21. Notes N/A
N/A Page 740 of 842

N/A
N/A
N/A
Specs C11
1. Valve Type Check
5. Standard API 602
21. Notes N/A

Specs C11 C16
5. Standard API 594
N/A Page 741 of 842

N/A
N/A
N/A
Specs C11
5. Standard API 594

Specs C12
5. Standard API 594
N/A Page 742 of 842

N/A
N/A
N/A
Specs C3
5. Standard API 594

Specs C23
5. Standard API 594
N/A Page 743 of 842

N/A
N/A
N/A
Specs C23
5. Standard API 594

Specs C23
5. Standard API 594
N/A Page 744 of 842

N/A
N/A
N/A
Specs C10
5. Standard API 594

Specs C4
5. Standard API 594
N/A Page 745 of 842

N/A
N/A
N/A
Specs C10
5. Standard API 594
21. Notes N/A

Specs C4 C10
5. Standard API 6D
21. Notes N/A
N/A Page 746 of 842

N/A
N/A
N/A
Specs C6 C19
5. Standard API 594

Specs C6 C19
5. Standard API 594
21. Notes N/A
N/A Page 747 of 842

N/A
N/A
N/A
Specs C6 C19
5. Standard API 6D
21. Notes N/A

Specs C30
5. Standard API 594
A.7.1.7.3)
21. Notes N/A
N/A Page 748 of 842

N/A
N/A
N/A
Specs C30
5. Standard API 594
A.7.1.7.3)
21. Notes N/A

Specs C30
5. Standard API 6D
A.7.1.7.3)
21. Notes N/A
N/A Page 749 of 842

N/A
N/A
N/A
Specs C11 C16
5. Standard API 594

Specs C11 C16
5. Standard API 594
21. Notes N/A
N/A Page 750 of 842

N/A
N/A
N/A
Specs C11 C16
5. Standard API 6D
21. Notes N/A

Specs C12
5. Standard API 594
21. Notes N/A
N/A Page 751 of 842

N/A
N/A
N/A
Specs C12
5. Standard API 6D
21. Notes N/A

Specs C30
1. Valve Type Check
5. Standard API 6D
21. Notes N/A
N/A Page 752 of 842

N/A
N/A
N/A
Specs C3
5. Standard API 594

Specs C3
5. Standard API 594
21. Notes N/A
N/A Page 753 of 842

N/A
N/A
N/A
Specs C3
5. Standard API 6D
21. Notes N/A

Specs C23
5. Standard API 6D
21. Notes N/A
N/A Page 754 of 842

N/A
N/A
N/A
Specs E6 E19
5. Standard API 594

Specs E16
5. Standard API 594
N/A Page 755 of 842

N/A
N/A
N/A
Valve Code VRE-600-2-A515
Specs E32
5. Standard API 594
item A.7.1.7.3)
21. Notes N/A
Valve Code VRE-600-2-A535

Specs E32
5. Standard API 6D
item A.7.1.7.3)
21. Notes N/A
N/A Page 756 of 842

N/A
N/A
N/A
Specs E6 E19
5. Standard API 594

Specs E6 E19
5. Standard API 594
21. Notes N/A
N/A Page 757 of 842

N/A
N/A
N/A
Specs E6 E19
5. Standard API 6D
21. Notes N/A

Specs E30
5. Standard API 594
A.7.1.7.3)
21. Notes N/A
N/A Page 758 of 842

N/A
N/A
N/A
Specs E30
5. Standard API 6D
A.7.1.7.3)
21. Notes N/A

Specs E16
5. Standard API 594
N/A Page 759 of 842

N/A
N/A
N/A
Specs E16
5. Standard API 594
21. Notes N/A

Specs E16
5. Standard API 6D
21. Notes N/A
N/A Page 760 of 842

N/A
N/A
N/A
Specs E3
5. Standard API 594

Specs E3
5. Standard API 594
21. Notes N/A
N/A Page 761 of 842

N/A
N/A
N/A
Specs E3
5. Standard API 6D
21. Notes N/A

Specs B10 C10
1. Valve Type Check
5. Standard API 602
7. End Connection Screwed ends ASME B1.20.1 NPT
21. Notes N/A
N/A Page 762 of 842

N/A
N/A
N/A
Specs B4 C4
1. Valve Type Check
5. Standard API 602
21. Notes N/A

Specs B6 B19 C6 C19
1. Valve Type Check
5. Standard API 602
21. Notes N/A
N/A Page 763 of 842

N/A
N/A
N/A
Specs B16 C16 E16
1. Valve Type Check
5. Standard API 602
21. Notes N/A

Specs B12 C12
1. Valve Type Check
5. Standard API 602
21. Notes N/A
N/A Page 764 of 842

N/A
N/A
N/A
Specs B30 C30
1. Valve Type Check
5. Standard API 602
21. Notes N/A

Specs B3 C3
1. Valve Type Check
5. Standard API 602
21. Notes N/A
N/A Page 765 of 842

N/A
N/A
N/A
Specs B10 C10
1. Valve Type Check
5. Standard API 602
21. Notes N/A

Specs B9 B10 C4
1. Valve Type Check
5. Standard API 602
21. Notes N/A
N/A Page 766 of 842

N/A
N/A
N/A
1. Valve Type Check
5. Standard API 602
21. Notes N/A

Specs B16 C16
1. Valve Type Check
5. Standard API 602
21. Notes N/A
N/A Page 767 of 842

N/A
N/A
N/A
Specs C12
1. Valve Type Check
5. Standard API 602
21. Notes N/A

1. Valve Type Check
5. Standard API 602
21. Notes N/A
N/A Page 768 of 842

N/A
N/A
N/A
Specs B3 C3 E3
1. Valve Type Check
5. Standard API 602
21. Notes N/A

Specs F3
5. Standard API 594
N/A Page 769 of 842

N/A
N/A
N/A
Specs F3
5. Standard API 594

Specs F3
5. Standard API 594
21. Notes N/A
N/A Page 770 of 842

N/A
N/A
N/A
Specs F3
5. Standard API 6D
21. Notes N/A
N/A Page 771 of 842

N/A
N/A
N/A
A.12.7 BUTTERFLY VALVES
Valve Code VBO-150-1-U204

Specs B22
1. Valve Type Butterfly, Lug type
4. Disc & Seat Configuration Concentric, trim 1
5. Standard API 609 Category A
11. Body Material ASTM A536 Gr. 65-45-12
12. Disc Material ASTM B148 (UNS C95800)
13. Seat Material FKM
14. Seal Ring N/A
10" - 20" Gearbox
18. Additional Requirement Dead-end Service per API 609.
20. Disc Coating N/A
21. Notes Through holes drilled and tapped according to ASME B1.1.

Specs B22
1. Valve Type Butterfly, Double Flanged (short pattern)
14. Seal Ring N/A
21. Notes N/A
N/A Page 772 of 842

N/A
N/A
N/A
Valve Code VBO-150-2-C111
Specs B4 B9 B10
4. Disc & Seat Configuration Double Offset
5. Standard API 609 Category B
12. Disc Material AISI 410 + ENP (acc. Item A.8.2.1.1)
13. Seat Material RPTFE
14. Seal Ring N/A
8" - 20" Gearbox
20. Disc Coating Electroless Nickel Plating (ENP)

Specs B4 B9 B10
7. End Connection 24" ASME B16.5, RF
14. Seal Ring N/A
21. Notes N/A
N/A Page 773 of 842

N/A
N/A
N/A
Specs B9 B10
4. Disc & Seat Configuration Double Offset, metal-seated
13. Seat Material AISI 316 + Metallic Coating (acc. Item A.7.5.4.3.2)
14. Seal Ring N/A
8" - 20" Gearbox

Specs B9 B10
14. Seal Ring N/A
21. Notes N/A
N/A Page 774 of 842

N/A
N/A
N/A
Specs B10
4. Disc & Seat Configuration Double Offset, fire tested
14. Seal Ring N/A
8" - 20" Gearbox
18. Additional Requirement Fire Tested (acc. item A.6.1.4). Dead-end Service per API 609.

Specs B10
14. Seal Ring N/A
N/A Page 775 of 842

N/A
N/A
N/A
Specs B6 B19
12. Disc Material AISI 316
14. Seal Ring N/A
8" - 20" Gearbox
21. Notes N/A

Specs B6 B19
14. Seal Ring N/A
21. Notes N/A
N/A Page 776 of 842

N/A
N/A
N/A
Specs B19
14. Seal Ring N/A
8" - 20" Gearbox
21. Notes N/A

Specs B19
14. Seal Ring N/A
21. Notes N/A
N/A Page 777 of 842

N/A
N/A
N/A
Valve Code VBO-150-2-D111
Specs B26
12. Disc Material ASTM A995 Gr 1b
14. Seal Ring N/A
8" - 20" Gearbox

Specs B26
7. End Connection 24" ASME B16.5, FF
26" - 36" ASME B16.47 Series A, FF
12. Disc Material ASTM A995 Gr 1b
14. Seal Ring N/A
N/A Page 778 of 842

N/A
N/A
N/A
Specs B11 B16
12. Disc Material Duplex (UNS S31803)
14. Seal Ring N/A
8" - 20" Gearbox

Specs B11 B16
14. Seal Ring N/A
21. Notes N/A
N/A Page 779 of 842

N/A
N/A
N/A
Specs B26
14. Seal Ring N/A
8" - 20" Gearbox

Specs B26
14. Seal Ring N/A
21. Notes Wafer valves shall not to be used with flamable or combustible services.
N/A Page 780 of 842

N/A
N/A
N/A
Specs B12
12. Disc Material Super Duplex (UNS S32760)
14. Seal Ring N/A
8" - 20" Gearbox

Specs B12
14. Seal Ring N/A
21. Notes N/A
N/A Page 781 of 842

N/A
N/A
N/A
Valve Code VBO-150-2-S211
Specs B3
14. Seal Ring N/A
8" - 20" Gearbox

Specs B3
14. Seal Ring N/A
21. Notes N/A
N/A Page 782 of 842

N/A
N/A
N/A
Specs B3
14. Seal Ring N/A
8" - 20" Gearbox
21. Notes N/A

Specs B3
14. Seal Ring N/A
21. Notes N/A
N/A Page 783 of 842

N/A
N/A
N/A
Specs B7 B23
14. Seal Ring N/A
8" - 20" Gearbox

Specs B7 B23
14. Seal Ring N/A
21. Notes N/A
N/A Page 784 of 842

N/A
N/A
N/A
Specs B14 B22
14. Seal Ring N/A
8" - 20" Gearbox

Specs B14 B22
7. End Connection 3" - 24" ASME B16.5, FF
14. Seal Ring N/A
8" - 48" Gearbox
21. Notes N/A
N/A Page 785 of 842

N/A
N/A
N/A
Specs B7 B23
14. Seal Ring N/A
8" - 20" Gearbox

Specs B7 B23
14. Seal Ring N/A
21. Notes N/A
N/A Page 786 of 842

N/A
N/A
N/A
Specs B10
4. Disc & Seat Configuration Triple Offset
14. Seal Ring Graphite Laminated with AISI 316
16. Stem Seal Material Graphite Based Seal
21. Notes Acceptance criteria for all HP/LP seat tests (Normative/Supplementary): ISO
5208 Rate A.

Specs B10
5208 Rate A.
N/A Page 787 of 842

N/A
N/A
N/A
Specs B4 B9 B10
4. Disc & Seat Configuration Triple Offset, fire tested
5208 Rate A.

Specs B4 B9 B10
5208 Rate A.
N/A Page 788 of 842

N/A
N/A
N/A
Specs B19
7. End Connection RF
5208 Rate A.

Specs B19
5208 Rate A.
N/A Page 789 of 842

N/A
N/A
N/A
Specs B6 B19
5208 Rate A.

Specs B6 B19
5208 Rate A.
N/A Page 790 of 842

N/A
N/A
N/A
Specs B11 B16
13. Seat Material Duplex (UNS S31803) + Metallic Coating (acc. Item A.7.5.4.3.2)
14. Seal Ring Graphite Laminated with Duplex (UNS S31803)
5208 Rate A.

Specs B11 B16
5208 Rate A.
N/A Page 791 of 842

N/A
N/A
N/A
Specs B12
13. Seat Material Super Duplex (UNS S32760) + Metallic Coating (acc. Item A.7.5.4.3.2)
14. Seal Ring Graphite Laminated with Super Duplex (UNS S32760)
5208 Rate A.

Specs B12
5208 Rate A.
N/A Page 792 of 842

N/A
N/A
N/A
Specs B3
5208 Rate A.

Specs B3
5208 Rate A.
N/A Page 793 of 842

N/A
N/A
N/A
Specs B3
5208 Rate A.

Specs B3
5208 Rate A.
N/A Page 794 of 842

N/A
N/A
N/A
Specs B7 B23
13. Seat Material ASTM B148 (UNS C95800) + Metallic Coating (acc. Item A.7.5.4.3.2)
14. Seal Ring Solid NAB (UNS C95800)
5208 Rate A.

Specs B7 B23
5208 Rate A.
N/A Page 795 of 842

N/A
N/A
N/A
Specs B14 B22
5208 Rate A.

Specs B14 B22
7. End Connection 24" ASME B16.5, FF
5208 Rate A.
N/A Page 796 of 842

N/A
N/A
N/A
Specs B14
14. Seal Ring N/A
10" - 20" Gearbox

Specs B14
14. Seal Ring N/A
21. Notes N/A
N/A Page 797 of 842

N/A
N/A
N/A
Specs B11
12. Disc Material ASTM A536 Gr 65-45-12 + Polyamide Disc Coating (acc. item A.8.2.3.2)
13. Seat Material NBR
14. Seal Ring N/A
10" - 20" Gearbox
20. Disc Coating Polyamide Disc Coating
21. Notes N/A

Specs B11
12. Disc Material ASTM A536 Gr 65-45-12 + Polyamide Disc Coating (acc. item A.8.2.3.2)
14. Seal Ring N/A
20. Disc Coating Polyamide Disc Coating
21. Notes N/A
N/A Page 798 of 842

N/A
N/A
N/A
Specs B3 B9 B10 B23
14. Seal Ring N/A
10" - 20" Gearbox

Specs B3 B9 B10 B23
14. Seal Ring N/A
21. Notes N/A
N/A Page 799 of 842

N/A
N/A
N/A
Specs C4 C10
14. Seal Ring N/A
8" - 20" Gearbox

Specs C4 C10
14. Seal Ring N/A
21. Notes N/A
N/A Page 800 of 842

N/A
N/A
N/A
Specs C4
13. Seat Material ASTM B564 (UNS N06625) + Metallic Coating (acc. Item A.7.5.4.3.2)
14. Seal Ring N/A
8" - 20" Gearbox

Specs C4
14. Seal Ring N/A
N/A Page 801 of 842

N/A
N/A
N/A
Specs C11 C16
14. Seal Ring N/A
8" - 20" Gearbox

Specs C16
14. Seal Ring N/A
21. Notes N/A
N/A Page 802 of 842

N/A
N/A
N/A
Specs C11 C16
14. Seal Ring N/A
8" - 20" Gearbox

Specs C16
14. Seal Ring N/A
N/A Page 803 of 842

N/A
N/A
N/A
Specs C12
14. Seal Ring N/A
8" - 20" Gearbox
21. Notes Wafer valves shall not to be used with flamable or combustible services.

Specs C12
14. Seal Ring N/A
21. Notes N/A
N/A Page 804 of 842

N/A
N/A
N/A
Specs C3
14. Seal Ring N/A
8" - 20" Gearbox
21. Notes N/A

Specs C3
14. Seal Ring N/A
21. Notes N/A
N/A Page 805 of 842

N/A
N/A
N/A
Specs C3
14. Seal Ring N/A
8" - 20" Gearbox
21. Notes N/A

Specs C3
14. Seal Ring N/A
21. Notes N/A
N/A Page 806 of 842

N/A
N/A
N/A
Specs C23
14. Seal Ring N/A
8" - 20" Gearbox

Specs C23
14. Seal Ring N/A
21. Notes N/A
N/A Page 807 of 842

N/A
N/A
N/A
Specs C4 C10
5208 Rate A.

Specs C4 C10
5208 Rate A.
N/A Page 808 of 842

N/A
N/A
N/A
Specs C6 C19
5208 Rate A.

Specs C6 C19
5208 Rate A.
N/A Page 809 of 842

N/A
N/A
N/A
Specs C11
5208 Rate A.

Specs C12
5208 Rate A.
N/A Page 810 of 842

N/A
N/A
N/A
Specs C12
5208 Rate A.
Valve Code VBO-600-3-A561

Specs E32
12. Disc Material ASTM A350 Gr LF3 + Inconel 625 weld overlay (acc. item A.7.1.7.3)
14. Seal Ring Graphite Laminated with ASTM B564 (UNS N06625)
20. Disc Coating Full clad - Inconel 625 weld overlay on all wetted parts
5208 Rate A.
N/A Page 811 of 842

N/A
N/A
N/A
Specs E16
5208 Rate A.

Specs E3
5208 Rate A.
N/A Page 812 of 842

N/A
N/A
N/A
Specs E3
5208 Rate A.

Specs F3
7. End Connection RTJ
5208 Rate A.
N/A Page 813 of 842

N/A
N/A
N/A
A.12.8 PLUG VALVES
Valve Code VMA-150-2-C101

Specs B10
1. Valve Type Plug
4. Obturator Type Expanding slips
5. Standard API 6D
11. Body Material ASTM A216 Gr WCB
12. Plug Material A216 WCB + ENP (acc. Item A.8.2.1.1)
13. Slips Material ASTM A395 Gr 60-40-18
14. Seat Insert Material FKM Type 2
15. Spring (Seat) Material ASTM A216 Gr WCB + ENP (acc. Item A.8.2.1.1)
16. Stem Seal Material FKM Type 2
6" - 24" Gearbox
19. Body Construction top entry, bottom entry
22. Notes N/A
Valve Code VMA-150-2-C1F1

Specs C10
1. Valve Type Plug
5. Standard API 6D
6" - 24" Gearbox
22. Notes N/A
N/A Page 814 of 842

N/A
N/A
N/A
Specs B6 B9
1. Valve Type Plug
5. Standard API 6D
11. Body Material ASTM A352 Gr LCC
12. Plug Material A352 LCB + ENP (acc. Item A.8.2.1.1)
13. Slips Material ASTM A352 Gr LCB
15. Spring (Seat) Material ASTM A352 Gr LCB + ENP (acc. Item A.8.2.1.1)
6" - 24" Gearbox
22. Notes N/A
Valve Code VMA-150-2-D301

Specs B12
1. Valve Type Plug
5. Standard API 6D
11. Body Material ASTM A995 Gr 6A
12. Plug Material A995 6a + ENP (acc. Item A.8.2.1.1)
13. Slips Material ASTM A995 Gr 6a
15. Spring (Seat) Material ASTM A995 Gr 6a
6" - 24" Gearbox
22. Notes N/A
N/A Page 815 of 842

N/A
N/A
N/A
Valve Code VMA-150-2-S201
Specs B3
1. Valve Type Plug
5. Standard API 6D
11. Body Material ASTM A351 Gr CF8M
12. Plug Material A351 CF8M + ENP (acc. Item A.8.2.1.1)
13. Slips Material ASTM A351 Gr CF8M
6" - 24" Gearbox
22. Notes N/A

Specs C10
1. Valve Type Plug
5. Standard API 6D
4" - 24" Gearbox
22. Notes N/A
N/A Page 816 of 842

N/A
N/A
N/A
Specs C6 C19
1. Valve Type Plug
5. Standard API 6D
4" - 24" Gearbox
22. Notes N/A

Specs C3
1. Valve Type Plug
5. Standard API 6D
4" - 24" Gearbox
22. Notes N/A
N/A Page 817 of 842

N/A
N/A
N/A
Specs E6 E19
1. Valve Type Plug
5. Standard API 6D
4" - 24" Gearbox
22. Notes N/A

Specs E3
1. Valve Type Plug
5. Standard API 6D
4" - 16" Gearbox
22. Notes N/A
N/A Page 818 of 842

N/A
N/A
N/A
Specs F3
1. Valve Type Plug
5. Standard API 6D
22. Notes N/A
N/A Page 819 of 842

N/A
N/A
N/A
A.12.9 NEEDLE VALVES
Valve Code VAG-150-1-D201
Specs B11
1. Valve Type Needle
4. Obturator Type Rising Plug
5. Standard ASME 16.34 LTD
7. End Connection Flanged ASME B16.5 (CL150), RF
15. Body Construction N/A
18. Stem Design rising stem, inside screw stem; Stem swivel
21. Notes N/A

Specs B14
21. Notes N/A
N/A Page 820 of 842

N/A
N/A
N/A
Specs B16 C16 E16
8. Pressure Class max. pressure 3000 psi
14. Stem Seal Material Graphoil
21. Notes N/A
Valve Code VAG-3000-1-D2F2

Specs B16 C16 E16
21. Notes N/A
N/A Page 821 of 842

N/A
N/A
N/A
Specs B12 C12
21. Notes N/A

Specs B12 C12
21. Notes N/A
N/A Page 822 of 842

N/A
N/A
N/A
Valve Code VAG-3000-1-N102
21. Notes N/A
Valve Code VAG-3000-1-N1F2

21. Notes N/A
N/A Page 823 of 842

N/A
N/A
N/A
Valve Code VAG-3000-1-S201
Specs B3 B4 B6 B9 B10 B17 B19 C3 C4 C6 C10 C19 E3 E6 E19 F3
12. Obturator Material Stainless Steel with hardness superior to seat
13. Seat Material ASTM A 182 Gr F316L
21. Notes N/A

Specs B3 B4 B6 B9 B10 B17 B19 C3 C4 C6 C10 C19 E3 E6 E19 F3
21. Notes N/A
N/A Page 824 of 842

N/A
N/A
N/A
Valve Code VAG-3000-1-S2F1
Specs B3 B6 B9 B10 B17 B19 C3 C6 C10 C19 E3 E6 E19 F3
21. Notes N/A

Specs B3 B6 B9 B10 B17 B19 C3 C6 C10 C19 E3 E6 E19 F3
21. Notes N/A
N/A Page 825 of 842

N/A
N/A
N/A
Specs C11
7. End Connection Flange ASME B16.5 (CL300), RF
21. Notes N/A

Specs G3
21. Notes N/A
N/A Page 826 of 842

N/A
N/A
N/A
Specs G3
21. Notes N/A

Specs G3
21. Notes N/A
N/A Page 827 of 842

N/A
N/A
N/A
Specs G3
21. Notes N/A

Specs H12
21. Notes N/A
N/A Page 828 of 842

N/A
N/A
N/A
Specs H12
21. Notes N/A
Valve Code VAG-6000-1-N102

Specs H30
21. Notes N/A
N/A Page 829 of 842

N/A
N/A
N/A
Valve Code VAG-6000-1-N1F2
Specs H30
21. Notes N/A

Specs H3 H6
21. Notes N/A
N/A Page 830 of 842

N/A
N/A
N/A
Specs H3 H6
21. Notes N/A

Specs H3
21. Notes N/A
N/A Page 831 of 842

N/A
N/A
N/A
Specs H3
21. Notes N/A
N/A Page 832 of 842

N/A
N/A
N/A
A.12.10 DIAPRAGM VALVES
Valve Code VDI-300-2-U301

Specs B7
1. Valve Type Diaphragm
4. Obturator Type Diaphragm
5. Standard According Manufacturer Standard
6. Size Range (NPS) 1 ½" - 12"
12. Diaphragm Material NBR
15. Adiitional Requirement Fire safe design (acc. item A.6.1.5)
16. Body Construction According to Manufacturer Standard
16. Stem Seal Material N/A
19. Notes N/A
N/A Page 833 of 842

N/A
N/A
N/A
A.12.11 AXIAL VALVES
Valve Code VAX-1500-3-S2F1
Specs G3
1. Valve Type Axial On-off
4. Obturator Type Piston type
7. End Connection ASME B16.5, Ring Type Joint
12. Obturator Material ASTM A 351 CF8M
13. Seat Material ASTM A351 CF8M
14. Seat Insert According to manufacturer standard, fitted to service conditions
15. Stem Material ASTM A322 (UNS G41300)
16. Stem Seal PEEK spring energized
21. Notes N/A
Valve Code VAX-2510-3-D301

Specs H12 H30
7. End Connection 2" - 3" ASME B16.5, Ring Type Joint
4" - 24" ISO 27509, IX seal ring
12. Obturator Material ASTM A995 Gr 6a
13. Seat Material ASTM A995 Gr 6a
21. Notes N/A
N/A Page 834 of 842

N/A
N/A
N/A
Valve Code VAX-2510-3-D3F1
Specs H12
21. Notes N/A
Valve Code VAX-2510-3-S2F1

Specs H3
12. Obturator Material ASTM A 351 CF8M
13. Seat Material ASTM A351 CF8M
21. Notes N/A
N/A Page 835 of 842

N/A
N/A
N/A
Specs H12 H30
7. End Connection ISO 27509, IX seal ring
6" - 12" ASME B16.5, Ring Type Joint
21. Notes N/A

Specs H12 H30
18. Additional Requirement Fire Tested (acc. item A.6.1.4); SIL-3 (see notes)
21. Notes SIL-3 requirements according A.6.1.6 (for HIPPS valves)
N/A Page 836 of 842

N/A
N/A
N/A
Specs H12
21. Notes N/A

Specs H12
notes)
21. Notes SIL-3 requirements according A.6.1.6 (for HIPPS valves)
N/A Page 837 of 842

N/A
N/A
N/A
A.12.12 BRONZE VALVES
Valve Code VAN-150-1-U101
Specs B7
1. Valve Type Angular Valve
7. End Connection Inlet: flange acc. B16.24 - Outlet: Male-threaded acc. NFPA 1693 2,5-7,5 NH
19. Body Construction screwed bonnet
22. Stem Design inside screw stem

Specs B14
1. Valve Type Gate Valve
7. End Connection Flat Face, ASME B16.24
19. Body Construction unnion bonnet
N/A Page 838 of 842

N/A
N/A
N/A
Specs B7
1. Valve Type Gate Valve
7. End Connection Screwed ends, ASME B1.20.1

Specs B7
1. Valve Type Globe Valve
7. End Connection Screwed ends, ASME B1.20.1
N/A Page 839 of 842

N/A
N/A
N/A
A.12.13 PLASTIC VALVES

Specs B22 B23
1. Valve Type Ball Valve
6. End Connection Flanged ASME B16.1, FF
10. Body Material glass-fiber reinforced vinyl ester
11. Obturator Material Glass fiber reinforced vinyl ester resin
12. Seat Material Glass fiber reinforced vinyl ester
17. Product Testing FAT according manufacturer standard
18. Notes Any metallic parts used in valve construction and in contact with process
fluid shall be made of ASTM B564 (UNS N10276), For use with temperatures
higher than ambient, see item A.7.6.2

Specs B26
11. Obturator Material Glass Fiber reinforced novolac epoxy
N/A Page 840 of 842

N/A
N/A
N/A
Specs B22 B23

Specs B26

Specs B22 B23
N/A Page 841 of 842
N/A
N/A
N/A
Specs B26
N/A Page 842 of 842

DISCIPLINE: PIPING
ANNEX B
PIPES │ FITTINGS │ ACESSORIES

(Mandatory)
INTERNA \ Força de Trabalho

DISCIPLINE: PIPING
INDEX
B.1. SCOPE .....................................................................................................................................3
B.2. NORMATIVE REFERENCES ...................................................................................................3
B.3. TERMS AND DEFINITIONS .....................................................................................................5
B.4. SYMBOLS AND ABBREVIATED TERMS ...............................................................................5
B.5. PIPES AND TUBES .................................................................................................................5
B.5.1. IDENTIFICATION CODE .......................................................................................................................................5
B.5.2. GENERAL INFORMATION .................................................................................................................................... 5
B.6. FITTINGS .................................................................................................................................5
B.6.2. GENERAL INFORMATION .................................................................................................................................... 8
B.7. NIPPLES ..................................................................................................................................8
B.8. FLANGES .................................................................................................................................9
B.8.2. GENERAL INFORMATION ..................................................................................................................................10
B.9. GASKETS ..............................................................................................................................10
B.9.1. IDENTIFICATION CODE .....................................................................................................................................10
B.9.2. GENERAL INFORMATION ..................................................................................................................................11
B.10. BOLTS AND NUTS .............................................................................................................11
B.10.1. IDENTIFICATION CODE ...................................................................................................................................11
B.10.2. GENERAL INFORMATION ................................................................................................................................11
B.11. ZINC-NICKEL COATING REQUIREMENTS ......................................................................12
B.12. ALTERNATIVE MATERIALS..............................................................................................12
B.13. DATASHEETS ....................................................................................................................13
- Rev. 13 - Page 2 of 13
DISCIPLINE: PIPING
B.1. SCOPE
This document defines requirements and material data sheets for pipes, fittings, flanges, gaskets and bolts, for use in
Exploration and Production (E&P) business area, onshore and offshore, especially in oil and gas production and their
process facilities.
B.2. NORMATIVE REFERENCES

ABNT NBR 5648 -Tubos e Conexões de PVC-U com Junta Soldável para Sistemas Prediais de Água Fria;
API SPEC 6A - Specification for Wellhead and Christmas Tree Equipment;
API SPEC 5L - Specification for Line Pipe;
ASME B1.1 - Unified Inch Screw Threads (UN and UNR Thread Form);
ASME B1.20.1 - Pipe Threads, General Purpose (Inch);
ASME B16.1 - Gray Iron Pipe Flanges and Flanged Fittings Classes 25, 125 and 250;
ASME B16.5 - Pipe Flanges and Flanged Fittings NPS 1/2 through NPS 24 Metric/Inch Standard;
ASME B16.9 - Factory-Made Wrought Steel Butt-Welding Fittings;
ASME B16.11 - Forged Fittings, Socket-Welding and Threaded;
ASME B16.14 - Ferrous Pipe Plugs, Bushings and Locknuts with Pipe Threads;
ASME B16.15 - Cast Copper Alloy Threaded Fitting Classes 125 and 250;
ASME B16.20 - Metallic Gaskets for Pipe Flanges Ring-Joint, Spiral-Wound and Jacketed;
ASME B16.21 - Nonmetallic Flat Gaskets for Pipe Flanges;
ASME B16.25 - Buttwelding Ends;
ASME B16.39 - Malleable Iron Threaded Pipe Unions Classes 150, 250 and 300;
ASME B16.47 - Large Diameter Steel Flanges NPS 26 through NPS 60 Metric/Inch Standard;
ASME B18.2.1 - Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex Flange, Lobed Head and
Lag Screws (Inch Series);
ASME B18.2.2 - Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange, and Coupling Nuts
(Inch Series);
ASME B31.3 - Process Piping;
ASME B31.4 - Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids;
ASME B31.8 - Gas Transmission and Distribution Piping Systems;
ASME B36.10 - Welded and Seamless Wrought Steel Pipe;
ASME B36.19 - Stainless Steel Pipe;
ASME BPVC Section VIII, Division I - Rules for Construction of Pressure Vessels;
ASTM A105/A105M - Standard Specification for Carbon Steel Forgings for Piping Applications;
ASTM A126 - Standard Specification for Gray Iron castings for Valves, Flanges, and Pipe Fittings;
- Rev. 13 - Page 3 of 13
DISCIPLINE: PIPING
ASTM A182/A182M - Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged
Fittings, and Valves and Parts for High-Temperature Service;
ASTM A193/A193M - Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature Service
or High Pressure Service and other Special Purpose Applications;
ASTM A194/A194M - Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High
Temperature Service, or Both;
ASTM A312/A312M - Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless
Steel Pipes;
ASTM A320/A320M - Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service;
ASTM A333/A333M - Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service;
ASTM A335/A335M - Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service;
ASTM A350/A350M - Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness
Testing for Piping Components;
ASTM A358/A358M - Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel
Pipe for High-Temperature Service and General Applications;
ASTM A671/A671M - Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower
Temperatures;
ASTM A672/A672M - Standard Specification for Electric-Fusion-Welded Steel Pipe for High-Pressure Service at
Moderate Temperatures;
ASTM A733 - Standard Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe
Nipples;
ASTM B841 - Standard Specification for Electrodeposited Coatings of Zinc Nickel Alloy Deposits
ASTM B849 - Standard Specification for Pre-Treatments of Iron or Steel for Reducing Risk of Hydrogen Embrittlement
ASTM B850 - Standard Guide for Post-Coating Treatments of Steel for Reducing the Risk of Hydrogen Embrittlement
ASTM F 1378 - Standard specification for performance of piping and tubing mechanically attached fittings
ASTM B62 - Standard Specification for Composition Bronze or Ounce Metal Castings;
EEMUA 144 - 90/10 copper nickel alloy piping for offshore applications – specification: tubes seamless and welded
EEMUA 145 - 90/10 copper nickel alloy piping for offshore applications – specification: flanges composite and solid
EEMUA 146 - 90/10 copper nickel alloy piping for offshore applications – specification: fittings
MSS SP-6 - Standard Finishes for Contact Faces of Pipe Flanges and Connecting - End Flanges of Valves and
Fittings;
MSS SP-43 - Wrought and Fabricated Butt-Welding Fittings for Low Pressure, Corrosion Resistant Applications;
MSS SP-83 - Class 3 000 Steel Pipe Unions, Socket Welding and Threaded;
MSS SP-95 - Swage (d) Nipples and Bull Plugs;
MSS SP-97 - Integrally Reinforced Forged Branch Outlet Fittings - Socket Welding, Threaded and Buttwelding Ends.
ISO 27509 - Petroleum and natural gas industries – compact flanged connections with IX seal ring
- Rev. 13 - Page 4 of 13
DISCIPLINE: PIPING
B.3. TERMS AND DEFINITIONS
B.4. SYMBOLS AND ABBREVIATED TERMS

B.5. PIPES AND TUBES

B.5.1. IDENTIFICATION CODE
Each pipe datasheet is identify by a code which follow the rule below:
T-XYY
Where:
X - Pipe material code, according to Table B.1.
YY - Sequencial number.
Table B.1 - Pipe material codes
MATERIAL CODE X
CARBON STEEL 1
ALLOYS AND ALLOY STELLS 2
STAINLESS STEEL 3
NON METTALICS 4
B.5.2. GENERAL INFORMATION
B.5.2.1. Shall not be used the following diameters (NPS): 3 ½, 5 and 22. NPS 1 ¼ and 2 ½ may be used only in non-
metallic piping and fittings.
B.5.2.2. The minimum piping diameter is NPS 1 for organic coat specs (11 and 14 group) in order to minimize flanges
connections.
B.5.2.3. The organic coating shall be according to annex F.
B.5.2.4. Specs with Inconel cladded pipes shall have monolithic pipes under NPS 4. For NPS 4 and greater the
Inconel cladding shall be according to annex G.
B.5.2.5. The thickness calculation for piggable specs is according to ASME B31.4/B31.8 for NPS equal and greater
than NPS 4. Under NPS 4 the thickness is according to ASME B31.3.
B.6. FITTINGS
Each fitting datasheet is identify by a code which follow the rule below:
CXX.Y-ZZ
Where:
- Rev. 13 - Page 5 of 13
DISCIPLINE: PIPING
XX - Fitting type, according to Table B.2.
Y - Sequencial number to use when necessary.
ZZ - Fitting material codes according to Table B.2.
Table B.2 - Fitting type and material
CODE CODE
FITTING TYPE FITTING TYPE
CXX.Y CXX.Y
Elbow 90º C01 Connector C37
Elbow 45º C02 Union Connector C38
Tee C03 Stub End type L C39
Reduction Tee C04 Elbow 45º - MAF C40
Cross C05 Elbow 90º - MAF C41
Coupling C06 Coupling - MAF C42
Half Coupling C07 Tee - MAF C43
Reduction Coupling C08 Union - MAF C44
Plug C09 Cap - MAF C45
Union – Plain seat type with
Union C10 C46
isolation gasket
Cap C11 Cap - MAF C45
Weldolet C12 Union – Flexible lug nut type C47
Elbow 90º LR (B16.9) C15 45° Tee C48
Elbow 45º LR (B16.9) C16 22°30' Elbow C49
Elbow 90º SR (B16.9) C17 11°15' deg Elbow C50
Reduction Concentric (B16.9) C18 Flanged Saddle C51
Reduction Eccentric (B16.9) C19 Threaded Saddle Flg C52
Tee (B16.9) C20 Reduction Cross C53
Reduction Tee (B16.9) C21 Thredolet C54
Cap (B16.9) C22 Sockolet C55
Reduction Bushing C23 Reducer Bushing C56
Cross (B16.9) C24 Elbow 45º SR C57
Elbow 45º 3D Radius C33 Y Tee - 30 Deg C58
Elbow 45º 5D Radius C34 Reduction Y Tee - 30 Deg C59
Elbow 90º 3D Radius C35 Cap Threade End C60
Elbow 90º 5D Radius C36
- Rev. 13 - Page 6 of 13
DISCIPLINE: PIPING
MATERIAL CODE ZZ MATERIAL CODE ZZ

A105 2 FRP Epoxy vinylester resins
A234 WPB 3 (bisphenol A ou brominated)
reinforced with fiberglass type
A350 LF2 Cl 1 4 53
E-CR, inner liner with fiberglass
A420 WPL6 5 veils type C. Suitable for 85°C
A420 WPL3 11 and 16 bar.
A182 F316L 14 FRP Bisphenol A Epoxy resins
A403 WP316L 15 reinforced with fiberglass type E
or E-CR, inner liner with
API 5L B PSL 1 SML 20 54
fiberglass veils type C or
API 5L X65 PSL 2 21 synthetic organic fibers.
A860 WPHY65 22 Suitable for 90 °C and 10 bar.
A333 8 23 FRP Bisphenol A Epoxy resins

A420 WPL8 24 reinforced with fiberglass type E
A522 Tp I 25 55
A182 F316 26 synthetic organic fibers.
A182 F51 (UNS S31803) 27 Suitable for 90 °C and 16 bar.
A790 (UNS S31803) 28 FRP Bisphenol A

Epoxy vinylester resins
A815 (UNS S31803) 29
reinforced with fiberglass type E
A182 F55 (UNS S32760) 30 or E-CR, inner liner with 56
A790 (UNS S32760) 31
synthetic organic fibers.
A815 (UNS S32760) 32 Suitable for 90 °C and 10 bar.
B366 (UNS N06625) 33 FRP Bisphenol A Epoxy resins
Cu-Ni 70/30 34 reinforced with fiberglass type E
Cu-Ni 90/10 (UNS C70620) 35 57
B62 (UNS C83600) 36 synthetic organic fibers.
A333 6 37 Suitable for 120 °C and 16 bar.
A312 TP316L 38 RPVC RJ/BS 58

B444 1 (UNS N06625) 39 RPVC RJ/SS 59
AISI 316 40 RPVC EJ/BS 60
ASTM A312 TP310H 41
ASTM A 403 Gr WP 316/316L 44
ASTM A 312 TP 316 / 316L 45
PVC 50 FRP Bisphenol A Epoxy
CPVC 51 vinylester resins reinforced with
fiberglass type E or E-CR, inner
FRP - Bisphenol A Epoxy 61
liner with fiberglass veils type C
resins reinforced with
52 or synthetic organic fibers.
fiberglass type E or E-CR.
Suitable for 90 °C and 16 bar.
Design pressure 10bar@90ºC
- Rev. 13 - Page 7 of 13
DISCIPLINE: PIPING
B.6.2.1. Maximum allowed thickeness reduction for 3D and 5D pipe bends are 15% and 10%, respectively.
B.6.2.2. The organic coating shall be according to Annex F.
B.6.2.3. The Inconel cladding shall be according to Annex G.
B.7. NIPPLES
Each nipple datasheet is identify by a code which follow the rule below:
N-XXYY
Where:
XX - Code that identify the relation of nipple types with end type, according to Table B.3.
YY - Nipple material code, according to Table B.3.
Table B.3 – Nipple type and material
CODE XX
END Female TE Male TE

PE BE TE BE x PE BE x TE MAF X X PE X TE
TYPE Male Capilar Male Capilar
CONCENTRIC C1 C2 C3 C4 C5 C6 - -
ECCENTRIC E1 E2 E3 E4 E5 - - -
STRAIGHT S1 S2 S3 - - - - - S9
CONNECTOR - - A3 - - - A7 A8
CODE CODE
MATERIAL MATERIAL
YY YY
ASTM A105 2 ASTM B366 (UNS N06625) 33
ASTM A234 Gr WPB 3 Cu-Ni 70/30 34
ASTM A350 Gr LF2 Cl 1 4 Cu-Ni 90/10 (UNS C70620) 35
ASTM A420 Gr WPL6 5 ASTM B62 (UNS C83600) 36
ASTM A420 Gr WPL3 11 ASTM A333 Gr 6 37
ASTM A182 Gr F316L 14 ASTM A312 TP316L 38
ASTM A403 Gr WP316L 15 ASTM B444 Gr 1 (UNS N06625) 39
API 5L Gr B PSL 1 seamless 20 PVC - ASTM D1785 class 1120 50
API 5L Gr X65 PSL 2 21 CPVC - ASTM F441 class 4120 51
ASTM A860 WPHY65 22 RPVC-Glass fiber reinforced PVC 52
ASTM A333 Gr 8 23 Glass fiber reinforced plastic
53
ASTM A420 Gr WPL8 24 suitable for 70°C and 16 bar
ASTM A522 Type I 25 Glass fiber reinforced plastic

54
ASTM A182 Gr F316 26 suitable for 90°C and 10 bar
- Rev. 13 - Page 8 of 13
DISCIPLINE: PIPING
ASTM A182 Gr F51 (UNS S31803) 27 Glass fiber reinforced plastic

55
ASTM A790 (UNS S31803) 28 suitable for 90°C and 16 bar
ASTM A815 (UNS S31803) 29 Glass fiber reinforced plastic
56
ASTM A182 Gr F55 (UNS S32760) 30 suitable for 120°C and 10 bar
ASTM A790 (UNS S32760) 31 Glass fiber reinforced plastic

57
ASTM A815 (UNS S32760) 32 suitable for 120°C and 16 bar
B.8. FLANGES
Each flange datasheet is identify by a code which follow the rule below:
F-class-XY
Where:
Class – Pressure class, according to Table B.4.
X – Code that identify the relation of flange face with flange type, according to Table B.4.
Y – Flange material codes according to Table B.4.
Table B.4 - Codes for flanges
CODE
CLASS MATERIAL
Y
150 ASME B16.5 ou B16.47 ASTM A105 Galvanized 1
300 ASME B16.5 ou B16.47 ASTM A105 2
600 ASME B16.5 ou B16.47 ASTM A350 Gr LF2 CL1 3
900 ASME B16.5 ou B16.47 ASTM A182 Gr F5 4
1500 ASME B16.5 ASTM A350 Gr LF3 5
ASME B16.5 ou ISO
2500 ASTM A182 Gr F304L 6
27509
10000 API 6A ASTM A182 Gr F316L 7
20 EEMUA ASTM A182 Gr F11 8
16 D4024 ASTM A182 Gr F317L 9
25 D4024 ASTM A182 Gr F347 A
ASTM A105 with cladded B
ASTM A694 Gr F65 C
ASTM A694 Gr F65 cladded D
ASTM A350 Gr LF3 cladded E
CODE X ASTM A182 Gr F316 F
Face Flange type ASTM A182 Gr F51 G
Type THD SO SW WN BL OR RJ EJ BF MAF INT ASTM A182 Gr F55 H
FF A B C D E F W X 1 ASTM A522 Type 1 J
RF G H J K L M Y Z ASTM A522 Tipo 1 cladded K
RTJ N P Q R S T ASTM B564 L
MSJ U V Cu-Ni 90/10 M
Cu-Ni 70/30 N
- Rev. 13 - Page 9 of 13
DISCIPLINE: PIPING
PVC P
CVPC Q
RPVC R
FRP 70°C S
FRP 90°C T
FRP 120°C U
B.8.2.1. The organic coating shall be according to Annex F.

B.8.2.2. The Inconel cladding shall be according to Annex G.
B.8.2.3. The composite welding neck flange is according to EEMUA 145, composed of a backing flange and a stub
end type L. The backing flange shall be epoxy coated following anexx F recommendations.
B.9. GASKETS
Each Gasket datasheet is identify by a code which follow the rule below:
J-class-XY
Where:
Class – Pressure class, according to Table B.5.
X – Code that identify the relation of flange face with gasket type, according to Table B.5.
Y – Flange material codes according to Table B.5.
Table B.5 - Codes for gaskets

Inner Centering Facing CODE
Flange Standard Class MATERIAL FILLER
Ring Ring layer Y
ASME B16.1 125 Aramide Fiber - - - - A
150 Neoprene - - - - B
PTFE
300 - - - - C
ASME B16.5 expanded
and 600 SBR - - - - D
ASME B16.47
900 AISI 304 Graphite AISI 304 Carbon steel - E
1500 AISI 316 Graphite AISI 316 Carbon steel - F
ASME B16.5 / ISO 27509 2500 AISI 316 Graphite AISI 317 Carbon steel - G
API 6A 10000 AISI 316 Graphite AISI 316 AISI 316 - H
AISI 347 Graphite - Carbon steel - J
MONEL PTFE MONEL Carbon steel - K
Duplex Graphite Duplex AISI 316 - L
CODE X Inconel 625 Graphite Inconel 625 AISI 316 - M
Face type Carbon Steel - - - - N
Gasket type
FP FR FJA MSJ A182 F5 - - - - P
Flat C P A182 F11 - - - - Q
Spiral Wound E A182 F347 - - - - R
Ring Joint A B AISI 304 - - - - S
- Rev. 13 - Page 10 of 13
DISCIPLINE: PIPING
Grooved G AISI 316 - - - - T

Isolation D F H A182 F51 - - - - U
Inconel 625 - - - - V
A522 TP I - - - - W
AISI 316 - - - PTFE X
Nitrile
Phenolic - - - Y
Rubber
AISI 316 - - - G10 Z
B.9.2.1. The Zinc-Nickel coating indicated in gaskets datasheets shall be according to item B.11.
B.9.2.2. Electric isolation gasket shall be according to Annex J.
B.10. BOLTS AND NUTS

Each Bolt and nut datasheet, is identify by a code which follow the rule below:
P-class-XX
Where:
Class – Flange pressure class
XX - Sequencial number.
Table B.6 - Codes for Bolts and Nuts
BOLT MATERIAL NUT MATERIAL CODE XX
ASTM A193 Gr. B7 ASTM A194 Gr. 2H 01
ASTM A320 Gr. L7 ASTM A194 Gr. 4L 02
ASTM A 193 Gr. B7, ASTM A 194 Gr. 2H,

07
revestido em Zn-Ni revestido em Zn-Ni
ASTM A 320 Gr. L7, ASTM A 194 Gr. 4L,
08
ASTM A320 Gr. L43, ASTM A194 Gr. 4L,

09
- Rev. 13 - Page 11 of 13
DISCIPLINE: PIPING
B.10.2.1. The studs, bolts and nuts shall be coated with zinc-nickel (Zn-Ni) according to item B.11.
B.11. ZINC-NICKEL COATING REQUIREMENTS
B.11.1. The procedure for studs, bolts, nuts, washers and gaskets Zn-Ni coating shall be in accordance with I-ET-
3010.00-1200-251-P4X-001 - REQUIREMENTS FOR BOLTING MATERIALS.
B.12. ALTERNATIVE MATERIALS
B.12.1. All materials listed in pipe specs shall be considered as standardized materials. Therefore, alternative
materials (equivalent or better) may be proposed, conditioned to PETROBRAS approval.
B.12.2. When substitutions were made shall be verified the wall thickness and the piping spec shall be updated.
B.12.3. Other altenative materials may be acceptable subject to Petrobras approval.
B.12.4. Some examples of alternative materials are in Table B.7
Table B.7 – Alternative Materials
Standardized material Alternative material
API 5L Gr B ASTM A 106 Gr B

API 5L Gr B API 5L Gr X65 PSL 2
API 5L Gr B ASTM A333 GR 6
Super duplex UNS S32760 Super duplex UNS S32750
Duplex UNS 31803 Super duplex UNS S32760 or UNS S32750
ASTM A234 WPB ASTM A420 WPL6
- Rev. 13 - Page 12 of 13
DISCIPLINE: PIPING
B.13. DATASHEETS
- Rev. 13 - Page 13 of 13
N/A
N/A
N/A
1. PIPES
PIPE
Commodity Code T-102

Specs B4 B9 B10 B11 B14 B17 B30 C4 C10 C11 C30
1. Item Pipe
2. Material API 5L Gr B PSL 1
4. Schedule (SCH) or thickness -
5. Ends ½" - 1 ½" NPT Threaded End , Plain End
2" - 44" Beveled End
6. Seam type ½" - 1 ½" Seamless
2" - 14" HFW , SAW , Seamless
16" - 24" HFW , SAW
26" - 44" SAW
8. Additional requirement -
9. Weight -
10. Dimension -

Specs B6 B19 C6 C19 E6 E19 H6
1. Item Pipe
2. Material ASTM A333 Gr 6
5. Ends ½" - 1 ½" Plain End
6. Seam type ½" - 10" Seamless
12" - 14" Seamless , Welded
16" - 28" Welded
9. Weight -
10. Dimension -
N/A Page 1 of 191

N/A
N/A
N/A
1. Item Pipe
2. Material ASTM A671 Gr CC60 Class 22
5. Ends Beveled End
6. Seam type 2" - 14" Seamless
16" - 44" Welded
9. Weight -
10. Dimension -

Specs E30 H30
1. Item Pipe
2. Material API 5L Gr X65 PSL 2
5. Ends 1" - 1 ½" Plain End
6. Seam type 1" - 1 ½" Seamless
2" - 14" SAW , Seamless
16" - 34" SAW
9. Weight -
10. Dimension -
N/A Page 2 of 191

N/A
N/A
N/A
Specs B7
1. Item Pipe
2. Material Cu-Ni 90/10 (UNS C7060X)
3. Standard EEMUA 234
5. Ends ½" - 2" Plain End
2 ½" - 36" Beveled End
6" - 16" Seamless , Welded
18" - 36" Welded
9. Weight -
10. Dimension -

Specs B30 C30 E30 E32 H30 J40
1. Item Pipe
2. Material ASTM B444 Gr 1 (UNS N06625)
3. Standard ASME B36.10/B36.19
6. Seam type Seamless
9. Weight -
10. Dimension -

Specs E32
1. Item Pipe
5. Ends Beveled End
6. Seam type 4" - 14" Seamless
16" - 30" Welded
9. Weight -
10. Dimension -
N/A Page 3 of 191

N/A
N/A
N/A
Specs
1. Item Pipe
2. Material ASTM A671 Gr CFE70 Class 32
5. Ends -
6. Seam type -
7. Size Range (NPS) -
9. Weight -
10. Dimension -

Specs B16 C16 E16
1. Item Pipe
2. Material ASTM A790 (UNS S31803)
10" - 14" Welded
9. Weight -
10. Dimension -

Specs B16 C16 E16
1. Item Pipe
2. Material ASTM A928 (UNS S31803 Cl 1 or 3)
5. Ends Beveled End
6. Seam type Welded
9. Weight -
10. Dimension -
N/A Page 4 of 191

N/A
N/A
N/A
Specs B12 C12 H12P H12 J12P J12
1. Item Pipe
2" - 8" Beveled End
8" Welded
9. Weight -
10. Dimension -

1. Item Pipe
10" - 48" Welded
9. Weight -
10. Dimension -

Specs B3 C3 E3 F3 G3 H3
1. Item Pipe
2. Material ASTM A312 TP 316/316L
2" - 6" Beveled End
6. Seam type ½" - 1 ½" Seamless
2" - 6" Welded
9. Weight -
10. Dimension -
N/A Page 5 of 191
N/A
N/A
N/A
1. Item Pipe
2. Material ASTM A358 Type 316/316L Cl 1 or 3
5. Ends Beveled End
6. Seam type Welded
9. Weight -
10. Dimension -

Specs B22
1. Item Pipe
2. Material FRP - Bisphenol A Epoxy resins reinforced with fiberglass type E or E-CR.
Design pressure 10 bar@90ºC.
5. Ends ½" - ¾" Plain End
1" - 8" Butt-Strap, Elastic Joint / Bell x Spigot Ends, Plain
End , Rigid Joint / Bell x Spigot Ends, Rigid Joint /
Spigot Ends
10" - 28" Butt-Strap, Elastic Joint / Bell x Spigot Ends, Rigid
Joint / Bell x Spigot Ends, Rigid Joint / Spigot Ends
30" - 48" Butt-Strap
9. Weight -
10. Dimension -
N/A Page 6 of 191

N/A
N/A
N/A
Specs
1. Item Pipe
2. Material FRP - Bisphenol A Epoxy vinylester resins reinforced with fiberglass type E or
E-CR. Design pressure 10 bar@90ºC.
5. Ends -
6. Seam type -
9. Weight -
10. Dimension -

Specs B23
1. Item Pipe
5. Ends Butt-Strap
9. Weight -
10. Dimension -

Specs
1. Item Pipe
E-CR. Design pressure 16 bar@90ºC.
5. Ends -
6. Seam type -
9. Weight -
10. Dimension -
N/A Page 7 of 191

N/A
N/A
N/A
Specs B26
1. Item Pipe
5. Ends Butt-Strap
9. Weight -
10. Dimension -

Specs B27
1. Item Pipe
2. Material FRP - Epoxy vinylester resins (bisphenol A brominated) reinforced with
fiberglass type E-CR, inner liner with fiberglass veils type C. Design pressure
16 bar@85ºC.
5. Ends Butt-Strap
9. Weight -
10. Dimension -

Specs C23
1. Item Pipe
5. Ends Butt-Strap
9. Weight -
10. Dimension -
N/A Page 8 of 191

N/A
N/A
N/A
2. FITTINGS
B12.2.1 5D 45 DEG PIPE BEND
Commodity Code !! EXISTING !! C34-39 ID155040

Specs
1. Fitting type 5D 45 deg Pipe Bend
3. Standard ASME B31.8 (ISO 15590-1 or ASME B16.49)
4. Pressure class or thickness -
5. End connections Beveled end
8. Weight -
9. Dimension -
Commodity Code C34-31

Specs H12P J12P
3. Standard NORSOK M-630 NBE2
8. Weight -
9. Dimension -

Specs H12P J12P
8. Weight -
9. Dimension -
N/A Page 9 of 191

N/A
N/A
N/A
Specs
2. Material ASTM A358 TP316/316L
8. Weight -
9. Dimension -
Commodity Code !! EXISTING !! C36-39 ID155044

Specs
8. Weight -
9. Dimension -

Specs H12P J12P
8. Weight -
9. Dimension -
N/A Page 10 of 191

N/A
N/A
N/A
Specs H12P J12P
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -
B12.2.3 90 DEG ELBOW, B16.11

Specs B4 B9 B10 B17 C4 C10
1. Fitting type 90 deg Elbow, B16.11
2. Material ASTM A105
4. Pressure class or thickness 3000
½" - 1 ½" 2000, 6000, 9000
5. End connections NPT Threaded End
½" - 1 ½" Socket Weld
8. Weight -
9. Dimension -
N/A Page 11 of 191

N/A
N/A
N/A
2. Material ASTM A350 Gr LF2 Cl 1
4. Pressure class or thickness 3000, 6000, 9000
5. End connections Socket Weld
8. Weight -
9. Dimension -

Specs
2. Material ASTM A420 Gr WPL8
5. End connections -
8. Weight -
9. Dimension -

Specs B16 C16 E16
2. Material ASTM A182 Gr F51 (UNS S31803)
8. Weight -
9. Dimension -
N/A Page 12 of 191

N/A
N/A
N/A
Specs B12 C12
8. Weight -
9. Dimension -

2. Material ASTM B366 (UNS N06625)
8. Weight -
9. Dimension -

Specs B7
4. Pressure class or thickness 20 bar
5. End connections Female Capilar
8. Weight -
9. Dimension -
N/A Page 13 of 191

N/A
N/A
N/A
Specs B3 C3 E3 F3 G3
2. Material ASTM A182 Gr F316/316L
8. Weight -
9. Dimension -
B12.2.4 45 DEG ELBOW, B16.11

5. End connections NPT Threaded End , Socket Weld
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 14 of 191

N/A
N/A
N/A
Specs B16 C16 E16
8. Weight -
9. Dimension -

Specs B12 C12
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 15 of 191

N/A
N/A
N/A
Specs B7
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
B12.2.5 TEE, B16.11

1. Fitting type Tee, B16.11
4. Pressure class or thickness 3000, 6000
¾" - 1 ½" 9000
N/A Page 16 of 191

N/A
N/A
N/A

Specs B16 C16 E16

Specs B12 C12

N/A Page 17 of 191

N/A
N/A
N/A
Specs B7

B12.2.6 REDUCING TEE, B16.11

1. Fitting type Reducing Tee, B16.11
8. Weight -
9. Dimension -
N/A Page 18 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -

Specs B12 C12
8. Weight -
9. Dimension -
N/A Page 19 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
B12.2.7 CROSS, B16.11
N/A Page 20 of 191

N/A
N/A
N/A
1. Fitting type Cross, B16.11
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -
N/A Page 21 of 191

N/A
N/A
N/A
Specs B12 C12
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
B12.2.8 COUPLING
N/A Page 22 of 191

N/A
N/A
N/A
1. Fitting type Coupling
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -
N/A Page 23 of 191

N/A
N/A
N/A
Specs B12 C12
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs B7
8. Weight -
9. Dimension -
N/A Page 24 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B22
8. Weight -
9. Dimension -

Specs
E-CR. Design pressure 10bar@90ºC.
8. Weight -
9. Dimension -
N/A Page 25 of 191

N/A
N/A
N/A
Specs B23
5. End connections Bell-Spigot
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -

Specs B26
1" - 16" 10 bar, 25 bar
5. End connections Butt-Strap
8. Weight -
9. Dimension -
N/A Page 26 of 191

N/A
N/A
N/A
Specs B27
2. Material FRP - Epoxy vinylester resins (bisphenol A or brominated) reinforced with
16bar@85ºC
8. Weight -
9. Dimension -

Specs C23
1" - 6" 16 bar
8. Weight -
9. Dimension -
B12.2.9 HALF COUPLING, B16.11

Specs
1. Fitting type Half Coupling, B16.11
N/A Page 27 of 191

N/A
N/A
N/A
Specs
2. Material PVC - ASTM D1784 class 12454
3. Standard ASTM D2464

Specs
2. Material CPVC - ASTM D1784 class 23447
3. Standard ASTM F439

Specs

Specs
N/A Page 28 of 191

N/A
N/A
N/A
Specs

Specs

Specs

Specs
16bar@85ºC
N/A Page 29 of 191

N/A
N/A
N/A
B12.2.10 REDUCING COUPLING, B16.11
1. Fitting type Reducing Coupling, B16.11
¾" NPT Threaded End
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -
N/A Page 30 of 191

N/A
N/A
N/A
Specs B12 C12
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs B7
5. End connections Female Capilar, Male x Female Capilar
6. Size Range (NPS) ¾" - 2"
8. Weight -
9. Dimension -
N/A Page 31 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -
N/A Page 32 of 191

N/A
N/A
N/A
Specs
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -
N/A Page 33 of 191

N/A
N/A
N/A
Specs
16bar@85ºC
8. Weight -
9. Dimension -
B12.2.11 HEX HEAD PLUG, B16.11

Specs
1. Fitting type Hex Head Plug, B16.11
2. Material ASTM A182 Gr F316
5. End connections Beveled End
8. Weight -
9. Dimension -

Specs B7
8. Weight -
9. Dimension -
N/A Page 34 of 191

N/A
N/A
N/A
Specs B22 B23 B26 C23
2. Material ASTM B62 (UNS C83600)
8. Weight -
9. Dimension -
B12.2.12 UNION
Specs B7
1. Fitting type Union
8. Weight -
9. Dimension -
B12.2.13 CAP, B16.11

1. Fitting type Cap, B16.11
1" - 1 ½" Beveled End
8. Weight -
9. Dimension -
N/A Page 35 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -

Specs B12 C12
8. Weight -
9. Dimension -
N/A Page 36 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B7
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
B12.2.14 WELDOLET
N/A Page 37 of 191

N/A
N/A
N/A
1. Fitting type Weldolet
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs E30 H30
8. Weight -
9. Dimension -
N/A Page 38 of 191

N/A
N/A
N/A
Specs B16 C16 E16
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs B30 C30 E30 E32 H30 J40
8. Weight -
9. Dimension -
N/A Page 39 of 191

N/A
N/A
N/A
Specs B7
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
B12.2.15 LONG RADIUS 90 DEG ELBOW

1. Fitting type Long Radius 90 deg Elbow
2. Material ASTM A234 Gr WPB
8. Weight -
9. Dimension -
N/A Page 40 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs E32
8. Weight -
9. Dimension -

Specs E30 H30
2. Material ASTM A860 WPHY65
4. Pressure class or thickness ""
8. Weight -
9. Dimension -
N/A Page 41 of 191

N/A
N/A
N/A
Specs B16 C16 E16
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs B30 C30 E30 E32 H30 J40
8. Weight -
9. Dimension -
N/A Page 42 of 191

N/A
N/A
N/A
Specs B7
8. Weight -
9. Dimension -

2. Material ASTM A403 Gr WP316/316L
8. Weight -
9. Dimension -

Specs B22
5. End connections Bell-Spigot, Butt-Strap
8. Weight -
9. Dimension -
N/A Page 43 of 191

N/A
N/A
N/A
Specs
8. Weight -
9. Dimension -

Specs B23
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -
N/A Page 44 of 191

N/A
N/A
N/A
Specs B26
8. Weight -
9. Dimension -

Specs B27
16bar@85ºC
8. Weight -
9. Dimension -

Specs
2. Material RPVC - Glass fiber reinforced PVC
3. Standard according to manufacturer
8. Weight -
9. Dimension -
N/A Page 45 of 191

N/A
N/A
N/A
Specs
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -

Specs C23
8. Weight -
9. Dimension -
B12.2.16 LONG RADIUS 45 DEG ELBOW
N/A Page 46 of 191

N/A
N/A
N/A


Specs E32

Specs E30 H30
N/A Page 47 of 191

N/A
N/A
N/A
Specs B16 C16 E16


Specs B30 C30 E30 E32 H30 J40

Specs B7
N/A Page 48 of 191

N/A
N/A
N/A

Specs B22

Specs

Specs B23
N/A Page 49 of 191

N/A
N/A
N/A
Specs

Specs B26

Specs B27
16bar@85ºC

Specs
N/A Page 50 of 191

N/A
N/A
N/A
Specs

Specs

Specs C23
B12.2.17 SHORT RADIUS 90 DEG ELBOW

1. Fitting type Short radius 90 deg Elbow
8. Weight -
9. Dimension -
N/A Page 51 of 191
N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs E32
8. Weight -
9. Dimension -

Specs E30 H30
8. Weight -
9. Dimension -
N/A Page 52 of 191

N/A
N/A
N/A
Specs B16 C16 E16
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs B30 C30 E30 E32 H30 J40
8. Weight -
9. Dimension -
N/A Page 53 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -
B12.2.18 CONCENTRIC REDUCING

1. Fitting type Concentric Reducing
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 54 of 191

N/A
N/A
N/A
Specs E32
8. Weight -
9. Dimension -

Specs E30 H30
8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -
N/A Page 55 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B30 C30 E30 E32 H30 J40
8. Weight -
9. Dimension -

Specs B7
8. Weight -
9. Dimension -
N/A Page 56 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -
B12.2.19 ECCENTRIC REDUCING

1. Fitting type Eccentric Reducing
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 57 of 191

N/A
N/A
N/A
Specs E32
8. Weight -
9. Dimension -

Specs E30 H30
8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -
N/A Page 58 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B30 C30 E30 E32 H30 J40
8. Weight -
9. Dimension -

Specs B7
8. Weight -
9. Dimension -
N/A Page 59 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -
B12.2.20 TEE
1. Fitting type Tee
8. Weight -
9. Dimension -

1. Fitting type Tee
8. Weight -
9. Dimension -
N/A Page 60 of 191

N/A
N/A
N/A
Specs E32
1. Fitting type Tee
8. Weight -
9. Dimension -

Specs E30 H30
1. Fitting type Tee
8. Weight -
9. Dimension -

Specs B16 C16 E16
1. Fitting type Tee
8. Weight -
9. Dimension -
N/A Page 61 of 191

N/A
N/A
N/A
1. Fitting type Tee
8. Weight -
9. Dimension -

Specs B30 C30 E30 E32 H30 J40
1. Fitting type Tee
8. Weight -
9. Dimension -

Specs B7
1. Fitting type Tee
8. Weight -
9. Dimension -
N/A Page 62 of 191

N/A
N/A
N/A
1. Fitting type Tee
8. Weight -
9. Dimension -

Specs
1. Fitting type Tee
8. Weight -
9. Dimension -

Specs
1. Fitting type Tee
8. Weight -
9. Dimension -
N/A Page 63 of 191

N/A
N/A
N/A
Specs B22
1. Fitting type Tee
8. Weight -
9. Dimension -

Specs
1. Fitting type Tee
8. Weight -
9. Dimension -

Specs B23
1. Fitting type Tee
8. Weight -
9. Dimension -
N/A Page 64 of 191

N/A
N/A
N/A
Specs
1. Fitting type Tee
8. Weight -
9. Dimension -

Specs B26
1. Fitting type Tee
8. Weight -
9. Dimension -

Specs B27
1. Fitting type Tee
16bar@85ºC
8. Weight -
9. Dimension -
N/A Page 65 of 191

N/A
N/A
N/A
Specs C23
1. Fitting type Tee
8. Weight -
9. Dimension -
B12.2.21 REDUCING TEE

1. Fitting type Reducing Tee
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 66 of 191

N/A
N/A
N/A
Specs E32
8. Weight -
9. Dimension -

Specs E30 H30
8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -
N/A Page 67 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B30 C30 E30 E32 H30 J40
8. Weight -
9. Dimension -

Specs B7
8. Weight -
9. Dimension -
N/A Page 68 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -
B12.2.22 CAP

1. Fitting type Cap
8. Weight -
9. Dimension -

1. Fitting type Cap
8. Weight -
9. Dimension -
N/A Page 69 of 191

N/A
N/A
N/A
Specs E32
1. Fitting type Cap
8. Weight -
9. Dimension -

Specs E30 H30
1. Fitting type Cap
8. Weight -
9. Dimension -

Specs B16 C16 E16
1. Fitting type Cap
8. Weight -
9. Dimension -
N/A Page 70 of 191

N/A
N/A
N/A
1. Fitting type Cap
8. Weight -
9. Dimension -

Specs B30 C30 E30 E32 H30 J40
1. Fitting type Cap
8. Weight -
9. Dimension -

Specs B7
1. Fitting type Cap
8. Weight -
9. Dimension -
N/A Page 71 of 191

N/A
N/A
N/A
1. Fitting type Cap
8. Weight -
9. Dimension -

Specs
1. Fitting type Cap
8. Weight -
9. Dimension -

Specs
1. Fitting type Cap
8. Weight -
9. Dimension -
B12.2.23 HEX HEAD BUSHING, B16.11
N/A Page 72 of 191

N/A
N/A
N/A
Specs B7
1. Fitting type Hex Head Bushing, B16.11
4. Pressure class or thickness 20 bar, 3000, 6000, 9000
1 ½" 10 bar, 16 bar, 25 bar
5. End connections Female Capilar, Female NPT Thread x Male Capilar, Male x Female Capilar,
NPT Threaded End , Socket Weld
1 ½" Butt-Strap, Elastic Joint / Bell x Spigot Ends, Rigid
Joint / Bell x Spigot Ends, Rigid Joint / Spigot Ends
B12.2.24 CROSS
1. Fitting type Cross
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 73 of 191

N/A
N/A
N/A
Specs E32
8. Weight -
9. Dimension -

Specs E30 H30
8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -
N/A Page 74 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B30 C30 E30 E32 H30 J40
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 75 of 191

N/A
N/A
N/A
Specs
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -

Specs H12P J12P
8. Weight -
9. Dimension -
N/A Page 76 of 191

N/A
N/A
N/A
Specs H12P J12P
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -

Specs H12P J12P
8. Weight -
9. Dimension -
N/A Page 77 of 191

N/A
N/A
N/A
Specs H12P J12P
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -
B12.2.27 CONNECTOR

Specs B7
1. Fitting type Connector
8. Weight -
9. Dimension -
B12.2.28 CONNECTOR UNION
N/A Page 78 of 191

N/A
N/A
N/A
Specs B7
1. Fitting type Connector Union
B12.2.29 STUB END WELDING NECK L TYPE

Specs B7
1. Fitting type Stub End Welding Neck L type
6" - 36" 16 bar
8. Weight -
9. Dimension -
B12.2.30 FLANGED SADDLE

Specs B22
1. Fitting type Flanged Saddle
8. Weight -
9. Dimension -
N/A Page 79 of 191

N/A
N/A
N/A
Specs
8. Weight -
9. Dimension -

Specs B23
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -
N/A Page 80 of 191

N/A
N/A
N/A
Specs B26
8. Weight -
9. Dimension -

Specs B27
16bar@85ºC
8. Weight -
9. Dimension -

Specs C23
8. Weight -
9. Dimension -
B12.2.31 THREADED SADDLE FLG
N/A Page 81 of 191

N/A
N/A
N/A
Specs B22
1. Fitting type Threaded Saddle Flg

Specs

Specs B23

Specs
N/A Page 82 of 191

N/A
N/A
N/A
Specs B26

Specs B27
16bar@85ºC

Specs C23
B12.2.32 SOCKOLET
N/A Page 83 of 191

N/A
N/A
N/A
1. Fitting type Sockolet
2" - 24" 9000
5. End connections Socket weld
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs
2. Material ASTM A182 Gr F316L
8. Weight -
9. Dimension -
N/A Page 84 of 191

N/A
N/A
N/A
Specs
8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -

Specs B12 C12
8. Weight -
9. Dimension -
N/A Page 85 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B7
5. End connections Capillary
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
B12.2.33 CONCENTRIC REDUCING, FRP
N/A Page 86 of 191

N/A
N/A
N/A
Specs B22
1. Fitting type Concentric Reducing, FRP
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -

Specs B23
8. Weight -
9. Dimension -
N/A Page 87 of 191

N/A
N/A
N/A
Specs
8. Weight -
9. Dimension -

Specs B26
8. Weight -
9. Dimension -

Specs B27
16bar@85ºC
8. Weight -
9. Dimension -
N/A Page 88 of 191

N/A
N/A
N/A
Specs C23
8. Weight -
9. Dimension -
B12.2.34 ECCENTRIC REDUCING, FRP

Specs B22
1. Fitting type Eccentric Reducing, FRP

Specs
N/A Page 89 of 191

N/A
N/A
N/A
Specs B23

Specs

Specs B26
N/A Page 90 of 191

N/A
N/A
N/A
Specs B27
16bar@85ºC

Specs C23
B12.2.35 FRP REDUCING TEE

Specs B22
1. Fitting type FRP Reducing Tee
8. Weight -
9. Dimension -
N/A Page 91 of 191

N/A
N/A
N/A
Specs
8. Weight -
9. Dimension -

Specs B23
4. Pressure class or thickness "", 16 bar
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -
N/A Page 92 of 191

N/A
N/A
N/A
Specs B26
8. Weight -
9. Dimension -

Specs B27
16bar@85ºC
8. Weight -
9. Dimension -

Specs C23
8. Weight -
9. Dimension -
B12.2.36 FRP STUB END
N/A Page 93 of 191

N/A
N/A
N/A
Specs B23
1. Fitting type FRP Stub End
4. Pressure class or thickness 1" - 1 ½" BellSpigot, Butt-Strap
2" - 2 ½" BellSpigot, BellSpigot16 bar, Butt-Strap
3" - 8" 16 bar, BellSpigot, BellSpigot16 bar, Butt-Strap
10" - 28" 16 bar, BellSpigot, BellSpigot16 bar, Butt-Strap,
Butt-Strap16 bar
30" - 44" 16 bar, BellSpigot, BellSpigot16 bar, Butt-Strap16
bar
46" 16 bar, BellSpigot16 bar, Butt-Strap16 bar
48" BellSpigot16 bar, Butt-Strap16 bar
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -
N/A Page 94 of 191

N/A
N/A
N/A
Specs B26
4. Pressure class or thickness 1" 16 bar
1 ½" - 2" 16 bar, Butt-Strap
2 ½" 16 bar, Butt-Strap, Butt-Strap16 bar
3" - 14" 16 bar, BellSpigot16 bar, Butt-Strap, Butt-Strap16
bar
16" 16 bar, BellSpigot16 bar, Butt-Strap
18" - 24" 16 bar, BellSpigot, BellSpigot16 bar
26" - 34" 16 bar, BellSpigot16 bar
36" BellSpigot16 bar
8. Weight -
9. Dimension -

Specs
16bar@85ºC
8. Weight -
9. Dimension -
N/A Page 95 of 191

N/A
N/A
N/A
Specs C23
4. Pressure class or thickness 1" Butt-Strap
1 ½" 25 bar, Bell-Spigot25 bar, Butt-Strap
2" - 3" 25 bar, Bell-Spigot25 bar, Butt-Strap, Butt-
Strap25 bar
4" - 24" 25 bar, Bell-Spigot, Bell-Spigot25 bar, Butt-Strap,
Butt-Strap25 bar
26" 25 bar, Bell-Spigot25 bar, Butt-Strap, Butt-
Strap25 bar
28" 25 bar, Butt-Strap25 bar
8. Weight -
9. Dimension -
N/A Page 96 of 191

N/A
N/A
N/A
3. NIPPLE
B12.3.1 CONNECTOR NIPPLE
Commodity Code N-A335

Specs B7
1. Nipple type Connector Nipple
5. End connections Threaded NPT Both Ends
8. Weight -
9. Dimension -

Specs B7
5. End connections Female NPT Thread x Female Capilar
8. Weight -
9. Dimension -

Specs B7
5. End connections Male NPT Thread x Female Capilar
8. Weight -
9. Dimension -
B12.3.2 SWAGE CONCENTRIC NIPPLE
N/A Page 97 of 191

N/A
N/A
N/A
Commodity Code N-C103
1. Nipple type Swage Concentric Nipple
5. End connections Plain Both Ends
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -
N/A Page 98 of 191

N/A
N/A
N/A
Specs B12 C12
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 99 of 191

N/A
N/A
N/A
Specs B11 B14 C11
5. End connections Bevel Both Ends
8. Weight -
9. Dimension -

Specs H6
8. Weight -
9. Dimension -

Specs H12 J12P J12
8. Weight -
9. Dimension -
N/A Page 100 of 191

N/A
N/A
N/A
Specs H30 J40
8. Weight -
9. Dimension -

Specs H3
8. Weight -
9. Dimension -

5. End connections Bevel Large End x Plain Small End
8. Weight -
9. Dimension -
N/A Page 101 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -

Specs B12 C12
8. Weight -
9. Dimension -
N/A Page 102 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
B12.3.3 SWAGE ECCENTRIC NIPPLE
Commodity Code N-E103

1. Nipple type Swage Eccentric Nipple
8. Weight -
9. Dimension -
N/A Page 103 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs B16 C16 E16
8. Weight -
9. Dimension -

Specs B12 C12
8. Weight -
9. Dimension -
N/A Page 104 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

Specs B11 B14 C11
8. Weight -
9. Dimension -
N/A Page 105 of 191

N/A
N/A
N/A
Specs H6
8. Weight -
9. Dimension -

Specs H12 J12P J12
8. Weight -
9. Dimension -

Specs H30 J40
8. Weight -
9. Dimension -
N/A Page 106 of 191

N/A
N/A
N/A
Specs H3
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 107 of 191

N/A
N/A
N/A
Specs B16 C12 C16 E16
8. Weight -
9. Dimension -

Specs B12
8. Weight -
9. Dimension -

6. Size Range (NPS) ¾" - 4"
8. Weight -
9. Dimension -
N/A Page 108 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -
B12.3.4 STRAIGHT NIPPLE
Commodity Code N-S120

1. Nipple type Straight Nipple
2. Material API 5L Gr B PSL 1 seamless
3. Standard ASTM A733
8. Weight -
9. Dimension -

Specs
8. Weight -
9. Dimension -
N/A Page 109 of 191

N/A
N/A
N/A
Specs B16 C16 E16
8. Weight -
9. Dimension -

Specs B12 C12
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 110 of 191

N/A
N/A
N/A
8. Weight -
9. Dimension -

Specs
2. Material Straight Nipple, NPT nut, ASTM A312 Grade TP 316, SC, ASTM A733
3. Standard -
8. Weight -
9. Dimension -

8. Weight -
9. Dimension -
N/A Page 111 of 191

N/A
N/A
N/A
Specs H12P H12 J12P J12
8. Weight -
9. Dimension -

Specs H6
8. Weight -
9. Dimension -

Specs H30 J40
8. Weight -
9. Dimension -
N/A Page 112 of 191

N/A
N/A
N/A
Specs H3
8. Weight -
9. Dimension -
N/A Page 113 of 191

N/A
N/A
N/A
4. FLANGES
B12.4.1 INTEGRAL FRP FLANGE
Commodity Code F-10-1T
Specs B22
1. Flange type Integral FRP Flange
Suitable for 90°C.
3. Standard ASTM D4024 - Drilling acc. B16.5/B16.47 CL150
4. Pressure class 10 bar
5. Flange facing Flat Face
6. Face finishing -
7. Coating -
11. Weight -
12. Dimension -
Commodity Code F-16-1S

Specs B27
fiberglass type E-CR. Suitable for 85°C.
6. Face finishing -
7. Coating -
11. Weight -
12. Dimension -
N/A Page 114 of 191

N/A
N/A
N/A
Commodity Code F-16-1U
Specs
Suitable for 120°C.
6. Face finishing -
7. Coating -
11. Weight -
12. Dimension -
B12.4.2 BLIND FLANGE
Commodity Code F-10-ET

Specs B22
1. Flange type Blind Flange
Suitable for 90°C.
6. Face finishing -
7. Coating -
11. Weight -
12. Dimension -
N/A Page 115 of 191

N/A
N/A
N/A
Commodity Code F-1500-SX
Specs F3 G3
4. Pressure class Class 1500
5. Flange facing Ring Type Joint
6. Face finishing Surface finish not exceed 63 μin.
7. Coating -
11. Weight -
12. Dimension -
Commodity Code F-150-E2

Specs B14
3. Standard ½" - 24" ASME B16.5
26" - 44" ASME B16.47 Series A
6. Face finishing 125-250 μin. surface finish
7. Coating -
11. Weight -
12. Dimension -
N/A Page 116 of 191

N/A
N/A
N/A
Commodity Code F-150-L2
Specs B4 B9 B10 B11 B17
5. Flange facing Raised Face
7. Coating -
11. Weight -
12. Dimension -
Commodity Code F-150-L3

Specs B6 B19
2. Material ASTM A350 Gr LF2 Class 1
7. Coating -
11. Weight -
12. Dimension -
N/A Page 117 of 191

N/A
N/A
N/A
Commodity Code F-150-LB
Specs B30
2. Material ASTM A105 Cladded
3. Standard 4" - 24" ASME B16.5
7. Coating Inconel (UNS N06625) clad
11. Weight -
12. Dimension -
Commodity Code F-150-LG

Specs B16
7. Coating -
11. Weight -
12. Dimension -
N/A Page 118 of 191

N/A
N/A
N/A
Commodity Code F-150-LH
Specs B12
7. Coating -
11. Weight -
12. Dimension -
Commodity Code F-150-LL

Specs B30
7. Coating -
11. Weight -
12. Dimension -
N/A Page 119 of 191

N/A
N/A
N/A
Commodity Code F-150-LX
Specs B3
7. Coating -
11. Weight -
12. Dimension -
Commodity Code F-150-LY

Specs B7
2. Material ASTM A105 Thermal Spray coated (note 126)
7. Coating -
11. Weight -
12. Dimension -
N/A Page 120 of 191

N/A
N/A
N/A
Commodity Code F-16-ES
Specs B27
fiberglass type E-CR. Suitable for 85°C.
6. Face finishing -
7. Coating -
11. Weight -
12. Dimension -
Commodity Code F-16-EU

Specs B26
Suitable for 120°C.
6. Face finishing -
7. Coating -
11. Weight -
12. Dimension -
N/A

Srge Piping Specification For Topsides: Technical Specification I-ET-3010.2D-1200-200-P4X-001

Uploaded by

Copyright:

Available Formats

Srge Piping Specification For Topsides: Technical Specification I-ET-3010.2D-1200-200-P4X-001

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Srge Piping Specification For Topsides: Technical Specification I-ET-3010.2D-1200-200-P4X-001

Uploaded by

Copyright:

Available Formats

Nº:

TECHNICAL SPECIFICATION I-ET-3010.2D-1200-200-P4X-001

REV. DESCRIPTION AND/OR REVISED SHEETS

REV. 0 REV. A REV. B REV. C REV. D REV. E REV. F REV. G REV. H

INTERNA \ Qualquer Usuário

A. Valves and Valve Datasheets

INTERNA \ Qualquer Usuário

INTERNA \ Qualquer Usuário

ASME B31.3 Process Piping.

INTERNA \ Qualquer Usuário

INTERNA \ Qualquer Usuário

API RP 14E Recommended Practice for Design and Installation of offshore

INTERNA \ Qualquer Usuário

INTERNA \ Qualquer Usuário

INTERNA \ Qualquer Usuário

INTERNA \ Qualquer Usuário

MSS SP 88 Diaphragm Type Valves.

3 SYMBOLS AND ABBREVIATED TERMS

AISI American Iron and Steel Institute

INTERNA \ Qualquer Usuário

INTERNA \ Qualquer Usuário

4 PIPING TAGGING SYSTEM

B – Service Symbols (as listed in Item 5)

C – Piping Material Specification Code

D – Sequential Numbering of Line

INTERNA \ Qualquer Usuário

Sequential Numbering: 0010

INTERNA \ Qualquer Usuário

5 PIPING SPECIFICATIONS X SERVICES

Code Service Specs

ADW Aerated Dilution Water B11, B23

AM Amine B10, B16, B3, B9, C10, C16, E10, E16, E3

CN Sodium Hypochlorite B14, B20, B27

Corrosive Chemical Injection

D Diesel B10, B3, C10, C3, H10

DOH Carbon Dioxide w/ Hydrocarbon J12P, J31, J31P

DW Distilled Water B3, R3B, R3C, S3B, S3C

FL Foam Line B1, B10, B7, B7R

FLC Concentrated Foam B3

FP Production and Drilling Fluid B5, C5, E5, F5, G5, H5

FW Fire Water (Sea Water) B24, B7, B7R, S7

Refrigerated Liquified Petroleum

HF Hot Fluid B4, C4

HWP Process Heating Water B4, C4, E4

HWU Utility Heating Water B21, B22, B23, B4

INTERNA \ Qualquer Usuário

Code Service Specs

IA Instrumentation Air B3, G3, R3B, R3C, S3B, S3C

IGN Ignition Line B3

IN Instrumentation Nitrogen B3, R3B, R3C, S3B, S3C

OL Lubrificating Oil B10, R9B, R9C, S9B, S9C

PW Potable Water B20, B3, R3B, R3C, S3B, S3C

S Steam B4, C4, E4, F4, G4, S9B, S9C

SA Service Air B1, B10, C10, R9B, R9C, S9B, S9C

SC Steam Condensate B4, C4, E4, F4, G4, S9B, S9C

SFW Fire Water (Fresh Water) A4

SN Start-up Nitrogen B1, B10, C10, R9B, R9C, S9B, S9C

STA Start-up Air C10H