Safety Data Sheet: Coenzyme A Sodium Salt Hydrate
Safety Data Sheet: Coenzyme A Sodium Salt Hydrate
Safety Data Sheet: Coenzyme A Sodium Salt Hydrate
4
Revision Date 03.08.2023
according to Regulation (EC) No. 1907/2006 Print Date 08.02.2024
GENERIC EU MSDS - NO COUNTRY SPECIFIC DATA - NO OEL DATA
1.2 Relevant identified uses of the substance or mixture and uses advised against
Identified uses : Laboratory chemicals, Manufacture of substances
1.3 Details of the supplier of the safety data sheet
Company : Sigma-Aldrich Chemical Pvt Limited
Industrial Area, Anekal Taluka
Plot No 12,
12 Bommasandra - Jigani Link Road
560100 BANGALORE
INDIA
1.4 Emergency telephone
Emergency Phone # : 000 800 1007 141 (CHEMTREC)
Ecological information:
The substance/mixture does not contain components considered to have endocrine
disrupting properties according to REACH Article 57(f) or Commission Delegated regulation
(EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher.
Toxicological information:
The substance/mixture does not contain components considered to have endocrine
disrupting properties according to REACH Article 57(f) or Commission Delegated regulation
(EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher.
Eye/face protection
Use equipment for eye protection tested and approved under appropriate
government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Skin protection
Handle with gloves. Gloves must be inspected prior to use. Use proper glove
removal technique (without touching glove's outer surface) to avoid skin contact
with this product. Dispose of contaminated gloves after use in accordance with
applicable laws and good laboratory practices. Wash and dry hands.
The selected protective gloves have to satisfy the specifications of Regulation (EU)
2016/425 and the standard EN 374 derived from it.
Full contact
Material: Nitrile rubber
Minimum layer thickness: 0,11 mm
Break through time: 480 min
Material tested:Dermatril® (KCL 740 / Aldrich Z677272, Size M)
Splash contact
Material: Nitrile rubber
Minimum layer thickness: 0,11 mm
Break through time: 480 min
Material tested:Dermatril® (KCL 740 / Aldrich Z677272, Size M)
data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 87300, e-mail
sales@kcl.de, test method: EN374
If used in solution, or mixed with other substances, and under conditions which
differ from EN 374, contact the supplier of the EC approved gloves. This
recommendation is advisory only and must be evaluated by an industrial hygienist
and safety officer familiar with the specific situation of anticipated use by our
customers. It should not be construed as offering an approval for any specific use
scenario.
Respiratory protection
required when dusts are generated.
Further information
The above information is believed to be correct but does not purport to be all inclusive
and shall be used only as a guide. The information in this document is based on the
present state of our knowledge and is applicable to the product with regard to
appropriate safety precautions. It does not represent any guarantee of the properties of
the product. Sigma-Aldrich Corporation and its Affiliates shall not be held liable for any
damage resulting from handling or from contact with the above product. See
www.sigma-aldrich.com and/or the reverse side of invoice or packing slip for additional
terms and conditions of sale.
Copyright 2020 Sigma-Aldrich Co. LLC. License granted to make unlimited paper copies
for internal use only.
The branding on the header and/or footer of this document may temporarily not visually
match the product purchased as we transition our branding. However, all of the
Sigma- C3144 Page 9 of 10