Iboost Manual v0.6
Iboost Manual v0.6
Iboost Manual v0.6
1
Thank you very much for purchasing this product.
In order to use this product correctly and safely, please be sure to read this instructions manual carefully.
This product's purpose is to control the boost of the turbocharger and improve the output of the engine.
2
INDEX
3
IMPORTANT NOTE-SAFETY
Please use this manual at your own risk. iBoost is not responsible for any damage or injury.
2. iBoost is designed to work until 30v DC and the ground is designed to be the chassis of the car.
3. Disconnect the Ground line from the battery during the installation of the iBoost.
4. DO NOT damage any wiring(s) and (or) piping(s) from the engine room during the installation of the
iBoost.
5. DO NOT install iBoost while the engine and its components are hot.
6. The installation of the iBoostMUST BE from a professional or a technician. Otherwise it will be at risk
7. The Regulation of the iBoostMUST BE done from a technician who has read the iBoost manual and
knows the boost limit of the car. Otherwise your engine will be at risk.
10. DO NOT insert extreme force to the product during the installation of the iBoost.
4
PART LIST
2 Stickers
INSTALLATION
Wiring
Power Connector
Black Connect to the Ground (chassis of the car)
Red Connect to the Power of the car (until 30 Volts).Must be install with 5 Amps Fuse.
5
Solenoid
Internal Westgate
Port 1: To atmosphere
External Westgate
Port 3: To atmosphere
IMPORTANTINFORMATION
iBoost recommends resetting the boost set point values to Zero and measure the new minimum boost
pressure before increasing your boost set point values.
6
When the valve working it will make sound.
Shorter Tubes Produce faster turbo spool.
MAIN MENU
Change Screens
7
iBoost has 5 Screen. With pressing Down/Up on
rotation switch user can change between screens
with one, two, three and four variables or Peak
Value Measurements (More about this screen
will be described on Peak Value Paragraph).
DEVICE SETTINGS
From main menu on OFF Mode by hold press inside the rotate switch you can enter on Device
Settings menu. To exit from the Device Settings hold press inside the rotate switch.
To navigate on Device Settings menu press Up/Down the rotation switch to move the circle. To
change a variable, press inside the rotation switch, now the circle is solid and you can change the
variable by pressing Up/Down Switch. When you finish the regulation press inside the rotation switch
to save the variable, now the circle will be empty and you can modify another variable or you can exit
from Device Settings.
Variables Explanation:
Start Screen:You can select the Start Up
screen when you power up iBoost.
Start Boost:You can select the startup Mode
when you power up iBoost.
Led Brightness:You can control the
9
brightness of bot leds (Blue and Read) by
changing this variable (1 is off 10 is full on).
Solenoid Hz:You can change the solenoid
frequency by modify this variable(iBoost
suggesting 35hz).
RpmSetup:
Shift Light:Select in which rpm you want
the shift light signal(Solid Red Led).
Prepare:Select how many rpm before the
shift light you want the prepare signal(Blink
Red Led).
Disp Warning:You can enable or disable a
Pop-Up window on main screen to inform
you about shift light and prepare signals.
Rpm In:Select the input of the rpm reading.
10
Out Setup:
Start Boost:In this pressure the output will
starting being enable.
Start Duty:With this Duty the output will
be start when the pressure reach the Start
Boost value.
Full Boost:Until this Pressure the output
will be progressive.
Full Duty:The Max Duty that you want to
reach your output.
Stop Boost:In this pressure your output
will be OFF(is this value is zero the stop is
disable).
Gear Setup:
To learn a gear the vehicle must be on moving.
Put a gear on gearbox and without pressing the
clutch move the circle on the running gear with
pressing Up/Down Rotation switch and press
inside the rotation switch for learning. This
routine must be done for all gears.
BOOST SETTINGS
12