Cat D400 GC®

DIESEL GENERATOR SETS

Standby: 60 Hz, 480V & 600V

Engine Model Cat® C13 In-line 6, 4-cycle diesel
Bore x Stroke 130mm x 157mm (5.1in x 6.2in)
Displacement 12.5 L (763 in³)
Compression Ratio 16.3:1
Aspiration Turbocharged Air-to-Air Aftercooled
Fuel Injection System MEUI
Governor Electronic ADEM™ A4

Standby Performance Strategy

EPA Certified for Stationary
400 ekW, 500 kVA
Emergency Application
PACKAGE PERFORMANCE
Performance Standby
Frequency 60 Hz
Genset Power Rating 500 kVA
Gen set power rating with fan @ 0.8 power factor 400 ekW
Emissions EPA TIER 3
Performance Number EM1694
Fuel Consumption
100% load with fan 105.8 L/hr 27.9 gal/hr
75% load with fan 90.7 L/hr 24.0 gal/hr
50% load with fan 66.2 L/hr 17.5 gal/hr
25% load with fan 37.7 l/hr 10.0 gal/hr
Cooling System 1

Radiator air flow restriction (system) 0.12 kPa 0.48 in. Water
Radiator air flow 497 m3/min 17551 cfm
Engine coolant capacity 14.2 L 3.8 gal
Radiator coolant capacity 30 L 8 gal
Total coolant capacity 34 L 12 gal
Inlet Air
Combustion air inlet flow rate 24.4 m³/min 966.6 cfm
Max. Allowable Combustion Air Inlet Temp 47 ° C 116 ° F
Exhaust System
Exhaust stack gas temperature 567.4 ° C 1053.4 ° F
Exhaust gas flow rate 82.0 m³/min 2894.9 cfm
Exhaust system backpressure (maximum allowable) 10.0 kPa 40.0 in. water
Heat Rejection
Heat rejection to jacket water 156 kW 8857 Btu/min
Heat rejection to exhaust (total) 398 kW 22607 Btu/min
Heat rejection to aftercooler 71 kW 4023 Btu/min
Heat rejection to atmosphere from engine 52 kW 2945 Btu/min
Heat rejection from alternator 29 kW 1661 Btu/min

LEHE2009-04 1/2
Cat C13 GC ®
DIESEL GENERATOR SETS

Emissions (Nominal)2 Standby

NOx 2274.7 mg/Nm³ 4.58 g/hp-hr
CO 666.9 mg/Nm³ 1.35 g/hp-hr
HC 6.2 mg/Nm³ 0.01 g/hp-hr
PM 39.4 mg/Nm³ 0.10 g/hp-hr
Alternator3
Voltages 480V 600V
Motor Starting Capability @ 30% Voltage Dip 871 731
Current 601.4 481.1
Frame Size M3134L4 M3115L4
Excitation S.E AREP
Temperature Rise 105°C 130°C

DEFINITIONS AND CONDITIONS APPLICABLE CODES AND STANDARDS:

1
For ambient and altitude capabilities consult your Cat dealer. Air flow AS1359, CSA C22.2 No100-04, UL142, UL489, UL869, UL2200, NFPA37, NFPA70,
restriction (system) is added to existing restriction from factory. NFPA99, NFPA110, IBC, IEC60034-1, ISO3046, ISO8528, NEMA MG1-22, NEMA
MG1-33, 2006/95/EC, 2006/42/EC, 2004/108/EC.
2
Emissions data measurement procedures are consistent with those described
in EPA CFR 40 Part 89, Subpart D & E and ISO8178-1 for measuring HC, CO, PM, Note: Codes may not be available in all model configurations. Please consult your
NOx. Data shown is based on steady state operating conditions of 77° F, 28.42 local Cat Dealer representative for availability.
in HG and number 2 diesel fuel with 35° API and LHV of 18,390 BTU/lb. The
nominal emissions data shown is subject to instrumentation, measurement , STANDBY: Output available with varying load for the duration of the interruption
facility and engine to engine variations. Emissions data is based on 100% load of the normal source power. Average power output is 70% of the standby power
and thus cannot be used to compare to EPA regulations which use values based rating. Typical operation is 200 hours per year, with maximum expected usage of
on a weighted cycle. 500 hours per year.

3
UL 2200 Listed packages may have oversized generators with a different RATINGS: Ratings are based on SAE J1349 standard conditions. These ratings
temperature rise and motor starting characteristics. Generator temperature rise also apply at ISO3046 standard conditions.
is based on a 40° C ambient per NEMA MG1-32.
Fuel Rates are based on fuel oil of 35º API [16º C (60º F)] gravity having an LHV of
42 780 kJ/kg (18,390 Btu/lb) when used at 29º C (85º F) and weighing 838.9 g/litre
(7.001 lbs/U.S. gal.). Additional ratings may be available for specific customer
requirements, contact your Caterpillar representative for details. For information
regarding Low Sulfur fuel and Biodiesel capability, please consult your Cat dealer.

LEHE2009-05 (05-20)
www.Cat.com/electricpower
©2020 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International
System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos, “Caterpillar Corporate Yellow”, the
“Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of 2/2
Caterpillar and may not be used without permission.
Cat GC ®
Control Panel

Image shown might not reflect actual configuration

GCCP 1.2 - Control Panel

GCCP 1.2 is an auto Start Control Module suitable for a wide variety of diesel gen-
set applications. Monitoring an extensive number of engine parameters, the
modules will display warnings, shutdown and engine status information on the back-
lit LCD screen, illuminated LEDs and remote PC.

FEATURES
• 4-line back-lit LCD text display
• Multiple display languages
• Five-key menu navigation
• LCD alarm indication
• Customisable power-up text and images
• Data logging facility
• Internal PLC editor
• Protections disable feature
• Fully configurable via PC using USB & RS485 communication
• Front panel configuration with PIN protection
• Power save mode
• 3-phase generator sensing and protection
• Generator current and power monitoring (kW, kvar, kVA, pf)
kW and kvar overload and reverse power alarms
• Over current protection
• Unbalanced load protection
• Breaker control via fascia buttons
• Fuel and start outputs configurable when using
CAN Support for 0 V to 10 V & 4 mA to 20 mA sensors
• 8 configurable digital inputs (3 available for Customer use)
• 8 configurable digital outputs (5 available for Customer use)
• 4 configurable analogue inputs (3 available for Customer Use)
• CAN, MPU and alternator frequency speed sensing in one variant
• Real time clock
• Engine pre-heat and post-heat functions
• Engine run-time scheduler
• Engine idle control for starting &stopping
• Fuel usage monitor and low fuel level alarms
• 3 configurable maintenance alarms

BENEFITS
• Hours counter provides accurate information for monitoring and maintenance periods
• User-friendly set-up and button layout for ease of use
• Multiple parameters are monitored & displayed simultaneously for full visibility
• The module can be configured to suit a wide range of applications for user flexibility
• PLC editor allows user configurable functions to meet user specific application requirements.
• RS485 Communication port can be used for the Remote Monitoring Communication (Compatible
with Cat PLG)

LEHE2017-02 (09-20)
www.Cat.com/electricpower
©2020 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos, “Caterpillar Corporate
Yellow”, the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
100 Amp Load Center

100 Amp Load Center

Specifications
Number of Spaces 6
System Voltage 120 / 240VAC
Number of Tandem Circuit
6
Breakers
Phase 1 Ph
NEMA Degree of Protection NEMA 3R Outdoor
Electrical Connection Lugs
Wiring Configuration 3-Wire
Tin Plated Aluminum
Material
Busbar
Enclosure Material Welded Galvanized Steel
Image shown may not reflect actual package.
Cover Finish Gray Baked Enamel
Product Certifications UL E-6294
AWG 8…AWG 1
Gauge
(Aluminium / Copper)

Dimensions and Specifications

Height / Width / Depth 321 mm / 226 mm / 127 mm
GFCI 16A (120V)
Battery Charger 6A (120V)
Jacket Water Heater 11.25A (240V)
Alternator Heater 1.04A (240V)
Total Load 34.29A Max

L1 L2
GFCI 16A (120V) Battery Charger 6A (120V)
Jacket Water Heater 11.25A (240V) Jacket Water Heater 11.25A (240V)
Alternator Heater 1.04A (240V) Alternator Heater 1.04A (240V)
Total Load 28.29A Max Total Load 18.29A Max

www.cat.com/electricpower
©2020 Caterpillar
All rights reserved.
Information contained in this publication may be considered confidential. Discretion is recommended when distributing.
Materials and specifications are subject to change without notice.
CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Corporate Yellow,” the “Power Edge”
and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks
LEHE2075-02 (04/20) of Caterpillar and may not be used without permission.
Circuit Breakers
C9 ACERT TM, C13 ACERT, C15 ACERT,
C18 ACERT Circuit Breakers
Manually Operated Circuit Breakers
Current Fram e Num ber Interrupting Ratings (kA rm s)
(A) of Poles Trip (Lugs) Cable Size
Auxiliary Options
240V 480V 600V Units Range / Phase

100 H 3 65 35 18 8-3/0 AWG

Electronic Form C (1NO + 1NC)
LSI (2) 3/0 – 250 Shunt Trip 24VDC
250 J 3 65 35 18 kcmil
(2) 3/0 – 250 1 Form C + 1 Bell Alarm
400 T5N 3 65 25 18
kcmil 250VAC/VDC
Electronic (3) 2/0 – 400 Shunt Trip 24VDC
600 T6N 3 65 35 20 LS/I kcmil
(S or I)
(3) 2/0 – 400 1 Form C + 1 Bell Alarm
800 T6N 3 65 35 20 or
LSI kcmil 400VAC / 250VDC
1200 T7S 3 65 50 25 (4) 2/0 – 500 Shunt Trip 24VDC
kcmil

1600 R 3 65 35 18 BUS BAR

2000 R 3 65 35 18 BUS BAR

Electronic Form C (1NO + 1NC)
LSI Shunt Trip 24VDC
2500 R 3 65 35 18 BUS BAR

BUS BAR
3000 R 3 65 35 18

Electrically Operated Circuit Break ers

Current Fram e Num ber Interrupting Ratings (kA rm s) (Lugs) Cable
(A) of Poles Trip
Size Range / Auxiliary Options
240V 480V 600V Units
Phase
Electronic (4) 4/0 – 500 kcmil 2 Form C + 1 Bell Alarm
800 T 7M-S 3 65 50 25 LSI 24VDC

Electronic (4) 4/0 – 500 kcmil 2 Form C + 1 Bell Alarm

1200 T 7M-S 3 65 50 25
LSI 24VDC
Electronic BUS BAR 2 Form C + 1 Bell Alarm
2000 T8M-S 3 125 125 100 LSI 24VDC

Electronic BUS BAR 2 Form C + 1 Bell Alarm

3000 T8M-S 3 125 125 100 LSI 24VDC

LEHE0942-06 1/18
Circuit Breakers
Single Breaker Options (250 – 3000A)
Model Current (A) Operation

C9 ACERT™ 250 Manually Operated

C9 ACERT 400 Manually Operated

C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 600 Manually Operated

C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 800 Manually Operated or Electrically Operated

C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 1200 Manually Operated or Electrically Operated

C13 ACERT, C15 ACERT, C18 ACERT 1600 Manually Operated

C15 ACERT, C18 ACERT 2000 Manually Operated or Electrically Operated

C18 ACERT 2500 Manually Operated

C18 ACERT 3000 Manually Operated or Electrically Operated

Multiple Breaker Options

Model Main Breaker Box Auxiliary Box
1st Breaker 2nd Breaker Breaker
(Am ps) (Am ps) (Am ps)
Manually Manually Manually Operated
Operated Operated

C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 250 250, 400, 600,
800, or 1200 3rd Breaker:
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 400
250 or 400 (Not
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 600
available if
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 800 1st & 2nd Breaker =
1200A)
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 1200

C13 ACERT, C15 ACERT, C18 ACERT 1600

C15 ACERT, C18 ACERT 2000

2nd Breaker:
Not Available
C18 ACERT 2500 250 or 400

C18 ACERT 3000

LEHE0942-06 2/18
Circuit Breakers

Figure 1

L EHE0942-06 3/18
Circuit Breakers

Figure 2

L EHE0942-06 4/18
Circuit Breakers
J-Frame 250 A Typical Peak Let-Through Curves

Figure 3

LEHE0942-06 5/18
Circuit Breakers
J-Frame 150-250 A (JD, JG, JJ, JL, and JR) Thermal-Magnetic
Trip

Figure 4

LEHE0942-06 6/18
Circuit Breakers
Ground Fault Module GFM250JD Trip Curve

Figure 5

LEHE0942-06 7/18
Circuit Breakers
T5 400/ 600 – PR221DS

Figure 6

LEHE0942-05 8/18
Circuit Breakers
T6 600 / 800 -PR221DS

Figure 7

LEHE0942-06 9/18
Circuit Breakers
T6 600 / 800 -PR221DS

Figure 8

LEHE0942-06 10/18
Circuit Breakers
Tmax T7 PR231/P Functions
L-S Functions

Figure 9

LEHE0942-06 11/18
Circuit Breakers
T6 800 - PR222DS and PR222DS/PD-A

Figure 10

LEHE0942-06 12/18
Circuit Breakers
T7 1000/1200 - PR232/P

Figure 11

LEHE0942-06 13/18
Circuit Breakers
T7 1000/1200 - PR332/P
L-S-I Functions

Figure 12

LEHE0942-06 14/18
Circuit Breakers
T8 1600/2000/2500/3000 – PR232/P-T8
L-S-I Functions

Figure - 13

LEHE0942-06 15/18
Circuit Breakers
P, R, NS-Frame Long-Short Trip Curve and NW-Frame Long-
Short Trip Curve

Figure - 14

LEHE0942-06 16/18
Circuit Breakers
P, R, NS-Frame Instant Curve and NW-Frame Instant Trip Curve

Figure 15

LEHE0942-06 17/18
Circuit Breakers
P, R, NS-Frame Ground Curve and NW-Frame Ground Fault Trip Curve

Figure - 16

LEHE0942-06 (05-20)

www.Cat.com/electricpower
© 2020 Caterpillar. All Rights Reserved. CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, "Caterpillar Corporate Yellow", the "Power Edge" and Cat “Modern Hex” trade dress as well
as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission
18/18
Note : The Information on this Document comesfrom a Third Party Sup plier and is not a Caterpillar Material
Attachments

Jacket Water Heater (WHHH01/

WHHH03)
Appropriate when the generator set is to be
sited in a low ambient environment, the heater
maintains the engine coolant at a temperature
[typically 38°C (100°F)] which facilitates rapid
starting and load acceptance. The heater
assembly uses UL compliant components (to
UL1030) and has CSA certification which is to
both CSA and UL Standards.
The heater itself is powered by a 240V for 60 Hz
AC auxiliary supply. A thermostatic controller is
included to regulate the output temperature to
within safe limits. When the generator set is not
running the heater is automatically connected to
the AC supply through a power relay mounted in
the control panel.
Features
• Uniform heat distribution Upon receiving a start signal the AC supply is
automatically disconnected by the power relay and
• Reduces wear from cold spots
automatically reconnected when the start signal is
• Improves startability removed, and the engine has stopped.
• Thermostatically controlled and protected
• 6’ (1.8m) cord length (577-1758)
• 16.4’ (5.0m) cord length (578-9355).
• Ensures generator is at optimal starting temperature and ready to accept load
• Durable pump with non-magnetic impeller that does not attract metal debris
• Robust die cast aluminum housing improves sealing of the hoses, eliminates leaking and breakage
• Corrosion resistant steel brackets for superior strength and durability
• Reduces thermal stress on coolant hoses
• Element designed for long life with maximum heat transfer
• IP44 Ingress Protection Rating
• No evaporation of coolant from hoses
• Reduces low coolant level alarms because coolant does not boil

Regulating Safety
Part No Outlet Location Watts Volts Amps Thermostat Thermostat
On 90°F (32°C)
577-1758/578-9355 Right 2700 240 11.25 Off 115°F (46°C) 210°F (98°C)

www.cat.com/electricpower
©2020 Caterpillar
All rights reserved.

Information contained in this publication may be considered confidential. Discretion is recommended when distributing.
Materials and specifications are subject to change without notice.
CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Corporate Yellow,” the “Power Edge”
and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks
of Caterpillar and may not be used without permission.
LEHE2077-01 (10/20)
Attachments
AC SUPPLY
VOLTAGE RANGE 90 V to 305 V (L-N)

FREQUENCY RANGE
48 Hz to 64 Hz (L-N)

DC OUTPUT RATING
10 A DC at 24 V DC

RIPPLE AND NOISE

<1%

EFFICIENCY
>86%

REGULATION LINE
Image shown might not reflect actual configuration
<0.5%

BATTERY CHARGER LOAD

2%
The intelligent battery charger has been developed with safety, usability, optimised TEMPERATURE SENSOR INPUT
battery performance and maximum battery lifetimes in mind. PT1000

A comprehensive range of input and output protections ensures a continued safe PROTECTIONS
charging environment also enabling the use of the charger as a power supply. Short Circuit
DC Over Voltage
DC Over Current
Reverse Polarity
FEATURES Over Temperature
• Intelligent two, three and four stage charging profiles AC Under & Over Voltage
• Configurable to suit most battery types (12V/24V)
CHARGE FAILURE RELAY
• Adjustable current limit
3 A at 30 V DC volt free relay
• Can be used as a battery charger, power supply or both at the same time
• Automatic or Manual boost and storage charge functions to help maintain battery condition
DIMENSIONS OVERALL
• Digital Microprocessor Technology
70 mm x200 mm x 130 mm
• Temperature compensation for battery charging 2.7” x 7.9” x 5.1”
• Low Output Ripple and superb line regulation
• Three LED Indicators WEIGHT
• AC input Under voltage 0.75 kg
• AC input Over voltage
• Battery charger output Over voltage OPERATING TEMPERATURE RANGE
• Battery charger output Over current -30 °C to +80 °C
• Optional battery temperature compensation with over temperature protection -22 °F to +176 °F
• Output short circuit and Inversion polarity with auto recovery
• Configurable charge termination STORAGE TEMPERATURE RANGE
• UL1236 /UL1564 Compliant -40 °C to +70 °C
-22 °F to +158 °F

Automatic Boost Mode

• Boosts and equalises cell charge improving battery performance and life

Power Save Mode

• Once the battery is fully charged the chargers switch to Eco-Power to save energy

Communication
• Can be integrated into external systems through MODBUS RTU using RS485
• Fully configurable via PC Software

BENEFITS
• Fully flexible to maximise the life of the battery
• Suitable for a wide range of battery types
• Switched mode design
BENEFITS
• Minimum 86% efficiency throughout full operating range
• No external intervention for boost mode
• Multiple chargers can be linked together to provide larger current output
• Can be permanently connected to battery and mains (utility) supply. No need to disconnect
through high load conditions.

LEHE2022-02 (10-20)
©2020 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos, “Caterpillar corporate
Yellow”, the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
GFCI Receptacles

20A Tamper-Resistant,
Weather-Resistant GFCI
Receptacles

Image shown may not reflect actual configuration.

Features and Benefits

• Automatically tests the GFCI every time the Product Features
reset button is pushed in. The GFCI will not • Grounding: GFCI ground fault
reset if the GFCI circuit is not functioning • Feature: Weather and tamper-resistant
properly. • Amperage: 20 Amp
• By blocking reset of the GFCI if protection • Voltage: 125 Volt
has been compromised, SmartLockPRO • NEMA: 5-20R
reduces the possibility of end-users incorrectly • Trip Level: Class A, 5mA plus or minus 1mA
assuming that a reset GFCI outlet is providing • Pole: 2
ground fault protection when it actually is not. • Wire: 3
• A line-load reversal diagnostic feature is • Color: White
provided which prevents the GFCI from being
Standards and Certifications
reset and stops power from being fed to the
• NEMA: WD-6
GFCI receptacle face or through to downstream
• ANSI: C-73
devices. A green LED indicator on the GFCI’s
• UL498: File E13399
face also illuminates to alert the installer to the
• CSA C22.2 No. 42: File LR-57811
line-load wiring reversal.
• NOM: 057
Weather-Resistant GFCIs • UL 943: File E48380
• Meet UL 498 requirements for weather-
resistant receptacles.
Receptacles contained in a
Tamper-Resistant GFCIs weather resistant box
• Shutter mechanism inside the receptacle and in-use cover.
blocks access to the contacts unless a two-
prong plug is inserted, helping ensure foreign
objects will be locked out.

www.Cat-ElectricPower.com
©2016 Caterpillar
All rights reserved.
Materials and specifications are subject to change without notice.
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow”,
the “Power Edge” trade dress as well as corporate and product identity used
LEHE1085-00 (5-16) herein, are trademarks of Caterpillar and may not be used without permission.
 Cat GC ®
Control Panel Options

ELECTRO-MAGNETIC COMPATIBILITY
BS EN 61000-6-2
EMC Generic Immunity Standard for the Industrial Environment
BS EN 61000-6-4
EMC Generic Emission Standard for the Industrial Environment

ELECTRICAL SAFETY
BS EN 60950
Safety of Information Technology Equipment, including Electrical
Business Equipment

TEMPERATURE
BS EN 60068-2-1
Ab/Ae Cold Test -30 °C BS EN 60068-2-2
Bb/Be Dry Heat+70°C

VIBRATION
BS EN 60068-2-6
Ten sweeps in each of three major axes
5 Hz to 8 Hz @ +/-7.5 mm, 8 Hz to 500 Hz @ 2 gn

Image shown might not reflect actual configuration SHOCK

BS EN 60068-2-27
Three shocks in each of three major axes 15 gn in 11 Ms

Remote Annunciator Module HUMIDITY

BS EN 60068-2-30
It is an LED expansion module that can be used with compatible control Db Damp Heat Cyclic 20/55 °C @ 95% RH 48 Hours
BS EN 60068-2-78
modules. The module has been designed to display a maximum of eight Cab Damp Heat Static 40 °C @ 93% RH 48 Hours
individual LED indications up to a maximum distance of 1 KM (0.6miles).
DEGREES OF PROTECTION PROVIDED BY ENCLOSURES BS EN
60529
The Annunciator will consist of two modules to provide a 16 Channel IP65 - Front of module when installed into the control panel with the
Fault annunciation. supplied sealing gasket.

It is presented in a vertical enclosure. It includes an alarm sounder that

is triggered when the host controller detects an alarm condition. The
CONTINUOUS VOLTAGE RATING
alarm can be muted using the front push button. 8 V to 35 V Continuous

The Panels will be fitted with removable label cards which can be used CRANKING DROPOUTS
Able to survive 0 V for 50 mS, providing supply was at least
to identify the standard NFPA alarms. If desired 10 V before dropout and supply recovers to 5 V. This is
achieved without the need for internal batteries. LEDs and
It includes individual LEDs for each channel and a ‘Power On’ LED that backlight will not be maintained during cranking.
flashes when the link with the host controller is lost. MAXIMUM OPERATING CURRENT
112 mA at 12 V, 53 mA at 24 V

MAXIMUM STANDBY CURRENT

• The Remote annunciator has an integral Sounder / Horn 74 mA at 12 V, 35 mA at 24 V
• Eight configurable LEDs (per module)
DIMENSIONS OVERALL
• Works up to 1 KM (0.6 miles) from the host controller 355 mm x 369 mm x 90 mm
• A single Controller can support five Caterpillar Configured
remote annunciator control boxes PANEL CUT-OUT
286 mm x 326 mm x 93 mm

8 mm

LEHE2021-01 (03-21)
www.Cat.com/electricpower
©2021 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos, “Caterpillar Corporate
Yellow”, the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
Cat GC ®
Control Panel Options

ELECTRO-MAGNETIC COMPATIBILITY
BS EN 61000-6-2
EMC Generic Immunity Standard for the Industrial Environment
BS EN 61000-6-4
EMC Generic Emission Standard for the Industrial Environment

ELECTRICAL SAFETY
BS EN 60950
Safety of Information Technology Equipment, including Electrical
Business Equipment

TEMPERATURE
BS EN 60068-2-1
Ab/Ae Cold Test -30 °C BS EN 60068-2-2
Bb/Be Dry Heat+70°C

OUTPUT EXPANSION MODULE VIBRATION

BS EN 60068-2-6
Output relay expansion module for use with compatible control modules. Ten sweeps in each of three major axes
5 Hz to 8 Hz @ +/-7.5 mm, 8 Hz to 500 Hz @ 2 gn
The Output Expansion module has been designed to extend a host
module’s output capabilities. SHOCK
BS EN 60068-2-27
Three shocks in each of three major axes 15 gn in 11 Ms
A maximum of 10 Output Expansion modules can be connected to an
individual module at any one time. All outputs are configurable via the HUMIDITY
BS EN 60068-2-30
host controller. Db Damp Heat Cyclic 20/55 °C @ 95% RH 48 Hours
BS EN 60068-2-78
The module will work up to 1 KM (0.6miles) from the host control module Cab Damp Heat Static 40 °C @ 93% RH 48 Hours

CONTINUOUS VOLTAGE RATING

8 V to 35 V Continuous

CRANKING DROPOUTS
Able to survive 0 V for 50 mS, providing supply was at least
10 V before dropout and supply recovers to 5 V. This is
• achieved without the need for internal batteries. LEDs and
backlight will not be maintained during cranking.

MAXIMUM OPERATING CURRENT

325 mA at 12 V, 152 mA at 24 V

MAXIMUM STANDBY CURRENT

70 mA at 12 V, 32 mA at 24 V

AUXILIARY RELAY CONTACTS

2 Amp DC rated voltage free

DIMENSIONS OVERALL
165 mm x 76 mm x 49 mm
6.5” x 3” x 1.9”

LEHE2020-00 (08-19)
www.Cat.com/electricpower
©2019 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow”,
the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
Cat GC ®
INTEGRAL FUEL TANKS

INTEGRAL FUEL TANKS

D250 GC – D600 GC

FEATURES

• UL Listed for United States (UL 142) and Canada INTEGRAL

(CAN/ULC S601)
• Facilitates compliance with NFPA 30 code, NFPA 37 and • Integral diesel fuel tank is incorporated into the
110 standards and CSA C282 code generator set base frame
• Robust base design includes linear vibration
• Dual wall
isolators between tank base and engine
• Low fuel level warning standard, customer configurable
generator.
warning or shutdown
• Primary tank leak detection switch in containment basin
• Tank design provides capacity for thermal expansion of OPTIONS
fuel
• Audio/visual fuel level alarm panel
• Fuel supply dip tube is positioned so as not to pick up
• 5gal (18.9 L) spill containment*
fuel sediment
• Locking Fuel Fill
• Fuel return and supply dip tube is separated by an
• Overfill prevention Valve*
internal baffle to prevent immediate re-supply of heated
return fuel *Applicable for D350GC-D600GC Models only
• Pressure washed with an iron phosphate solution
• Interior tank surfaces coated with a solvent-based thin-
film rust preventative
• Heavy gauge steel gussets with internal lifting rings
• Primary and secondary tanks are leak tested at 20.7 kPa
(3 psi) minimum
• Compatible with open packages and enclosures
• Gloss black polyester alkyd enamel exterior paint
• Welded steel containment basin (minimum of 110% of
primary tank capacity)
• Direct reading fuel gauge with variable electrical output
• Emergency vents on primary and secondary tanks are
sized in accordance with NFPA 30.

LEHE2015-01
Cat GC ®
INTEGRAL FUEL TANKS

Integral Fuel Tank Base Useable Capacities with Fuel Tank Dimensions & Weights
Standby Width Width
ekW mm in
250-300 1430 56.3
350-400 1630 64.1
450-500 1630 64.1
550-600 1865 73.4

WIDTH
HEIGHT
LENGTH

The heights listed above do not include lumber used during manufacturing and shipping

A. Open Set & Sound Attenuated Enclosure

Overall Package Height

Tank Only
Tank Total Useable with Tank
Feature Capacity Capacity
Design Dry
Code Height ‘H’ Length ‘L’ Open Enclosure
Weight
Litre Gallon Litre Gallon kg lb mm in mm in mm in mm in
FTDW035 2270.7 599.8 2059.9 543.9 970 2138 762.4 30.0 3958 155.8 2202 86.7 2487 97.9

Integral FTDW036 2820 744.9 2553 674.4 1165 2568 818.8 32.2 4815 189.5 2584 101.7 2644 104
Tank FTDW037 3671 969.7 3323 877.8 1331 2934 668.2 26.3 4622 181.9 2456 96.7 2644 104

FTDW038 4292 1133.8 3889 1027.3 1657 3653 816.4 32.1 4980 196 2560 100.7 2721 107.1

LEHE2015-02
Cat GC ®
INTEGRAL FUEL TANKS

B. Estimated Run Time (Hours)

Standby Ratings (kVA)

Tank Design Feature Code

ekW 100% 75% 50%
Hrs L/hr Hrs L/hr Hrs L/hr
250 28.1 73.3 35 58.8 47 43.8
FTDW035
300 24 86.0 30.8 66.8 40 51.5
350 27.1 94.3 31.2 81.9 42.4 60.2
FTDW036
400 24.1 105.9 28.1 90.7 38.6 66.2
Integral Tank
450 25.2 131.7 31.3 106.1 42.0 79.1
FTDW037
500 24.3 137 30.1 110.5 46.6 71.3
550 25.7 151.1 32.9 118.1 45.2 86.1
FTDW038
600 24.1 161.6 30.0 129.6 42.4 91.7

Tanks with full electrical stub-up area include removable end channel. Tanks with RH stub-up include stubup area directly below the
circuit breaker or power terminal strips.

Fuel tanks and applicable options facilitate compliance with the following United States NFPA Code and Standards:
NFPA 30: Flammable and Combustible Liquids Code
NFPA 37: Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines
NFPA 110: Standard for Emergency and Standby Power Systems

Fuel tanks and applicable options facilitate compliance with the following Canadian Standard and Code:
CSA C282 – Emergency Electrical Power Supply for Buildings
CSA B139-09 – Installation Code for Oil-Burning Equipment

LEHE2015-02 (01-20)
www.Cat.com/electricpower
©2020 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow”, the “Power
Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
Cat GC ®
ENCLOSURES

SOUND ATTENUATED LEVEL 2

ENCLOSURES
D250GC – D600GC
60 Hz

FEATURES

Robust / Highly Corrosion Resistant Construction Sound Attenuated Level 2

• Factory installed on skid base or tanks base • Caterpillar white paint
• Environmentally friendly, polyester powder baked paint • UL Listed integral fuel tank with 24 hours running time
• Enclosure constructed with 18-gauge steel capacity (Optional).
• Interior zinc plated fasteners • DC lighting package (Optional)
• Internally mounted exhaust silencing system
• Comply with ASCE /SEI 7 for Wind loads up to 100mph
• Designed and tested to comply with UL 2200 Listed
generator set package

Excellent Access
• Large cable entry area for installation ease.
• Accommodates side mounted single or multiple breakers.
• Two doors on both sides.
• Vertically hinged allow 180° opening rotation
• Radiator fill cover.

Security and Safety

• Lockable access doors which give full access to control
panel and breaker.
• Cooling fan and battery charging alternator fully guarded.
• Fuel fill, oil fill and battery can only be reached via
lockable access.
• Externally mounted emergency stop button (Optional).
• Designed for spreader bar lifting to ensure safety.
• Stub-up area is rodent proof.

LEHE2014-02
 Cat GC ®
ENCLOSURES

Enclosure Package Operating Characteristics

Sound Pressure
Cooling Air Flow Ambient
Standby Levels (dBA) at
Enclosure Type Rate Capability*
ekW 7m (23 ft)
m3 /s cfm °C °F 100% Load
250 6.4 13561 57 135 74
300 6.4 13561 51 125 74
350 7.4 15680 57 134 71
400 7.4 15680 53 127 71
Level 2 Sound Attenuated Enclosure (Steel)
450 8.4 17692 54 130 73
500 8.4 17692 50 122 73
550 11.2 23731 56 133 73
600 11.2 23731 53 127 73
*Cooling system performance at sea level. Consult your Cat® dealer for site specific ambient and altitude capabilities.
Note: Sound level measurements are subject to instrumentation, installation and manufacturing variability, as well as ambient site conditions.

Sound Attenuated Enclosure on Skid Base

Sound Attenuated Enclosure on a UL Listed Integral Fuel Tank Base

Image shown might not reflect actual configuration

LEHE2014-02
Cat GC ®
ENCLOSURES

Standby
Length, L Width, W Height, H Package Weights
Enclosure Type Ratings,
ekW mm in mm in mm in kg lb
Sound Attenuated Enclosure on 250 2857 6298.6
3958 155.8 1440 56.7 1991 78.4
Skid Base 300 2945 6492.6
350 3983 8781.0
4633 182.4 1630 64.2 2227 87.7
400 4017 8856.0
450 4408 9718.0
4823 189.8 1630 64.2 2777 109.3
500 4457 9826.0
550 4754 10480.8
4980 196.1 1865 73.4 2723 107.2
600 4837 10663.8
Sound Attenuated Enclosure on 250 3497 7709.6
UL Listed Integral Fuel Tank 3958 155.8 1440 56.7 2487 97.9
300 3585 7903.6
Base 350 4765 10505.0
4633 182.4 1630 64.2 2644 104.1
400 4799 10580.0
450 5345 11783.7
4823 189.8 1630 64.2 2777 109.3
500 5394 11891.7
550 5973 13168.2
4980 196.1 1865 73.4 2723 107.2
600 6056 13351.2

LEHE2014-02 (09-19)
www.Cat.com/electricpower
©2019 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos,
“Caterpillar Yellow”, the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

L L

THIS DIAGRAM IS FOR GC GENSET MODELS (250kW to 600kW)

K
FOR USE WITH : C9, C13, C15 & C18 ENGINES K

6310 CONTROLLER

J J

I I

H H

SIGNAL NAMES SYMBOL LEGEND TABLE INDEX TABLE

SHEET INDEX DESCRIPTION
CIRCUIT_ID COLOR DESCRIPTION 1 CROSS REFERENCE SHEET INDEX, NOTES
MINIATURE CIRCUIT BREAKER
10 WH AVR_SUPPLY_X2_(SHUNT) 2 CONTROL SCHEMATIC
101 RD UNFUSED_BTRY_(+) WIRE NAME DEFINITION 3 POWER SCHEMATIC
105 WH (+24V_DC)_ECM_SUPPLY 4 OPTION SCHEMATIC
108 WH (+24V_DC_)_PANEL_SUPPLY EMERGENCY STOP PUSHBUTTON 5 OPTION SCHEMATIC (CONTINUED)
123 FUSED BTRY +
XXXX-XX# XX-XX
WH 6 CUSTOMER CONNECTIONS AND COMPONENT DETAILS .
14 WH AVR_SUPPLY_X1_(PMG)
G 148 WH (+24_VDC)_LIGHTING_SUPPLY G
15 WH AVR_SUPPLY_X2_(PMG)
16 WH AVR_SUPPLY_Z1_(PMG) WIRE GAUGE FUSED AUTOMOTIVE RELAY
200 GN-YL GROUND
208 WH BATTERY_(-)
229 CLEAN_GROUND WIRE COLOUR
WH
344 WH EMERGENCY_STOP
345 WH EMERGENCY_STOP WIRE NUMBER RESISTOR
346 WH EMERGENCY_STOP HARNESS LAYER TABLE
347 WH EMERGENCY_STOP HARNESS IDENT
348 WH EMERGENCY_STOP IDENT PART NO CHG LOC DESCRIPTION NOTE
5+ GENERATOR_EXCITATION_(+) HARNESS AS. - - - - -
WH
6- GENERATOR_EXCITATION_(-) CIRCUIT IDENT EARTH/GROUND A 572-5793 02 SH 2 MAIN HARNESS (C9-C13)
WH
879 WH REMOTE_START_INPUT A 572-5795 02 SH 2 MAIN HARNESS (C15-C18)
F F
892 BK CAT_DATA_LINK_(-) AN 578-6063 01 SH 4 ANNUNCIATOR HARNESS
893 WH CAT_DATA_LINK_(+) B 577-8429 01 SH 4 PLG 641 & 601 HARNESS (RS485)
9 WH AVR_SUPPLY_X1_(SHUNT) C 580-2678 00 SH 2 E-STOP LINK (OPEN SET)
951 WH MODBUS A CURRENT TRANSFORMER CE 581-0536 00 SH 5 LC BATTERY CHARGER
952 BK MODBUS B COLOUR ABBREVIATIONS CD 577-8711 00 SH 5 GFCI
953 CU MODBUS COM CF 581-0537 00 SH 5 LC ALT HEATER
1 1
954 WH DSENET A PANEL TERMINAL E 572-5798 02 SH 2 E-STOP HARNESS (ENCLOSED SET)
ABBREVIATION DESCRIPTION X
955 BK DSENET B 1 1 EL 580-3699 01 SH 4 CANOPY LIGHTS HARNESS
956 CU DSENET SCREEN
RD RED ER 578-7682 01 SH 5 BATTERY CHARGER HARNESS
WH WHITE TERMINAL GF 581-1932 SH 5 GROUND FAULT RELAY INDICATION HARNESS
SCR CU SCREEN 01
A309 WH DIGITAL_INPUT_(GENSET RUNNING) OR ORANGE GR 579-3092 00 SH 4 GENSET RUNNING & COMMON ALARM
A666 WH ENCLOSURE_LIGHTING YL YELLOW PG 443-0637 00 SH 4 PMG ADAPTOR
A774 WH EMERGENCY_STOP T 577-3930 00 SH 4 PLG 641 & 601 HARNESS (POWER)
E PK PINK CONNECTOR E
A775 WH EMERGENCY_STOP RC 580-8446 01 SH 5 ALTERNATOR HEATER HARNESS
AC101 FUSED BTRY CHARGER (L) BK BLACK AX TBA - SH3 1200A CB AUX CONTACT HARNESS
WH
AC102 BTRY CHARGER (L) GY GREY FF TBA - SH3 1200A CB SHUNT TRIP HARNESS
WH
AC103 WH ALT HEATER BREAKER PU PURPLE Y 586-4861 00 SH 5 PLG CANBUS HARNESS
+
AC104 WH ALT HEATER BREAKER BR BROWN BATTERY
AC199 BTRY CHARGER (N) WIRE AS. / CABLE AS. - - - - -
WH GN GREEN
AC703 ALT HEATER RELAY (11) N - - SH 2 BATTERY NEGATIVE
WH
AC719 ALT HEATER RELAY (12)
BU BLUE P - - SH 2 BATTERY POSSITVE
WH SPLICE
AC720 ALT HEATER TERM CU COPPER R - - SH 2 BATTERY LINK
WH
E486 SENSING_VOLTAGE-PHASE_A GN-YL GREEN-YELLOW SEE SHEET 3 - - SH 2 400A POWER CABLES
WH
E487 SENSING_VOLTAGE-PHASE_B WIRE SEE SHEET 3 - - SH 3 600A POWER CABLES
WH
E488 SENSING_VOLTAGE-PHASE_C SEE SHEET 3 - - SH 3 800A POWER CABLES
WH
E494 CT_SENSING-PHASE_A SEE SHEET 3 - - SH 3 1200A POWER CABLES
WH
D E495 WH CT_SENSING-PHASE_B SCREEN CABLE D
E496 WH CT_SENSING-PHASE_C
E498 WH CT_SENSING-COMMON
E600
E601
WH
WH
GROUND FAULT RELAY
GROUND FAULT RELAY
ABBREVIATIONS A FUSE
F409 WH SENSING_VOLTAGE-NEUTRAL
F430 DIGITAL_INPUT_(D) ABBREVIATIONS DESCRIPTION
WH
F434 GEN_PHASE_A AC ALTERNATING CURRENT
WH
F435 GEN_PHASE_B AVR AUTOMATIC VOLTAGE REGULATOR
WH
F436 GEN_PHASE_C BATT BATTERY
WH
N756 HORN_OUTPUT CR CONTROL RELAY
WH
P733 ANALOG_I/P_SIGNAL_(FUEL_LEVEL) DC DIRECT CURRENT
WH
P854 BREAKER_SHUNT_TRIP ECM ENGINE CONTROL MODULE
WH
R958 DIGITAL_OUTPUT_(SHUNT_TRIP) ECR ENGINE CRANK RELAY
C WH C
R959 DIGITAL_OUTPUT_(ENCLOSURE_LIGHTS) ELR EMNVLOSURE LIGHTS RELAY
WH
X861 STARTER_MAG_SWITCH E-STOP EMERGENCY STOP
WH
Y797 YL J1939_DATALINK_(CAN_+) FLS FUEL LEVEL SENDER
Y798 BK J1939_DATALINK_(CAN_-) GFR GERNERAL FAULT RELAY
Y799 CU J1939_DATALINK_(CAN_SHLD) GND GROUND
Y983 DIGITAL_INPUT_(LOW_COOLANT_LEVEL) GRR GENERATOR RUNNING RELAY
WH
Y984 DIGITAL_INPUT_(FUEL_LEAK) LCL LOW COOLANT LEVEL
WH
Y985 DIGITAL_INPUT__(ENCLOSURE_LIGHTS) MCB MINIATURE CIRCUIT BREAKER
WH
PMG PERMANENT MAGNET GENERATOR
STR SHUNT TRIP RELAY
TERM PANEL TERMINAL
VFC VOLT FREE CONTACT

B B

M
A
T
NOTE A: FACTORY WIRING NOT PROVIDED AS STANDARD. REFER TO MANUFACTURER INSTALLATION INSTRUCTIONS. L
HT
TR

NOTE B: CONTACT OPEN IN DE-ENERGIZED STATE OR FAULT CONDITION. 1E5167A INT-PROP

1E0198W BRAND MARKINGS
1E0013Y CONFIDENTIALITY
NOTE C: RESISTOR TO BE REMOVED IF ADDITIONAL EXPANSION MODULES ARE CONNECTED. 1E0012A INTERPRETATION
N 1E0011 INTPR & TOL
O
T
E Caterpillar: Confidential Yellow
PROD X OTHER
UNLESS OTHERWISE SPECIFIED
VERSION PRIMARY X
DIMENSIONS ARE IN mm
A DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
THIRD ANGLE SHEET 1 OF 6
PROJECTION
DWG CONTROL W591

THE INFORMATION HEREON IS THE PROPERTY OF CATERPILLAR INC. AND/OR ITS

SUBSIDIARIES. WITHOUT WRITTEN PERMISSION, ANY COPYING, TRANSMITTAL TO
OTHERS, AND ANY USE EXCEPT THAT FOR WHICH IT IS LOANED, IS PROHIBITED

DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 2X3
- 02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

L
CONTROL SCHEMATIC (DSE 6310) L

ADEM A4:E4
A-C3
ECM 160-7689

J1-PIN3 ANALOG RTN 3

J1-PIN2 5V ANALOG POWER 2
SPARE ANALOG INPUT
J1-PIN17 PROG. ANALOG 3 17 (NOTE A)
6310 CONTROLLER
J1-PIN67 BATT - 67
K 20 MPU + K
CUSTOMER TERMINALS
MAG PICKUP (NOT USED) 21 MPU -
(NOTE A)
22 MPU SCR
CBL-A2:Y799-A3 CU-20 A-T10 1 1 A-T16
CBL-A3:Y799-A3 CU-18 A-T25

25 ECU SCR (J1939)

CAN SH
J1-PIN42 CAN A SHIELD 42 A-T11
1 1 CBL-A3:Y797-A2 YL-18 A-T23

23 ECU + (J1939)
A-S3

J1-PIN50 CAN A + 50 Y797-A2 WH-18 CBL-A2:Y797-A2 WH-18 A-T12 1 1 A-T18

CBL-A3:Y798-A1 GN-18 A-T24

24 ECU - (J1939)
A-S4 CAN+
J1-PIN34 CAN A- 34 Y798-A3 WH-18 A-T13
1 1
120R
CBL-A2:Y798-A1 BK-18 A-T14 1 1

CAN-
Resistor_As_3_Nodes_1 A-T15
1 1 A-T17

134-2540 A-C2
155-2267
J J
A Y797-A20 WH-18 A-C1
265-4123
B Y798-A44 WH-18
CBL-A4:Y798-A1 BK-18 F
C REF [16,F] 208-A22 WH-18 A-T61

1 DC SUPPLY (-)
120 CBL-A4:Y797-A2 WH-18 G
ENGINE SERVICE E-STOP_PANEL REF [10,D] 108-A25 WH-18 A-T62
DC SUPPLY (+)
2
CBL-A4:Y799-A3 CU-20 C CONNECTOR 390--1209

J1-PIN8 ATA/CAT+ 8 CBL-A5:893-A2 WH-18 D

J1-PIN9 ATA/CAT- 9 CBL-A5:892-A1 BK-18 E 12 11
A-T19 A-T21
A775-A29 WH-18 A-T26

3 EMERGENCY STOP NC (POS)

A-CLIPPED_2

CBL-A5:200-A3 CU-20 A-CLIPPED_1

J 22 21
A-T20 A-T22

347-A28 WH-18 REF [7,E]

J1-PIN23 GND SW 2 E-STOP 23 A774-A32 WH-18 H
I REF [16,F] 208-A54 WH-18 B I
REF [10,D] 108-A55 WH-18 A
J1-PIN40 GND SW 3 RUN-STOP 40
OPEN SET LINK ENCLOSURE ESTOP
C-C32 E-STOP 4 OUTPUT A (NOT USED)
3E-3376 390--1209
REF [12,G] X861-A30 WH-18 A-T27

5 OUTPUT B (STARTER MOTOR)

1
12 11 E-C1 A-C5 6 CHARGE ALT EXCITE (NOT USED)
2 E-T1 E-T3
3E-3376 155-2272
CONNECT TO A-C5
22 21
344-C54 WH-18 3 E-T2 E-T4
A774-E4 WH-18 1
348-C55 WH-18 4 345-E3 WH-18 2 346-A46 WH-18
344-E1 WH-18 3 344-A27 WH-18 REF [6,E]
H 348-E2 WH-18 4 348-A26 WH-18 H

J1-PIN48 BATT + 48 105-A11 WH-16 OPTIONAL

J1-PIN52 BATT + 52 105-A10 WH-16
F5
AUDIBLE STR
352--2951
J1-PIN53 BATT + 415-2232 ALARM
53 105-A9 WH-16
241-3114
25A REF [16,F]
A-S7

J1-PIN70 KEY SW 70 105-A8 WH-16 105-A7 WH-14 A-T53 A-T63

101-A45 WH-14 Horn_1 208-A47 WH-18 A-T68 A-T67

R958-A50 WH-18 A-T66

7 OUTPUT C (SHUNT TRIP)

A2 A1

J1-PIN61 BATT - 61 208-A14 WH-16 A-T6

8 OUTPUT D (SPARE)
A-T7

J1-PIN63 BATT - 63 208-A12 WH-16 9 OUTPUT E (SPARE)

G J1-PIN65 BATT - 208-A13 WH-16 208-A56 WH-18 OUTPUT F (SPARE)
G
65 REF[16,E] 10
11 OUTPUT G (SPARE)
N756-A57 WH-18 A-T76

12 OUTPUT H (SPARE)
CUSTOMER TERMINALS
A-S2

208-A16 WH-10 208-A24 WH-18 X861-A30 WH-18 REF [3,I]

REF [13,A] 229-A58 WH-18 A-T78
1 1 A-T64
229-A53 WH-16 REF [12,E]
CLN_GND
REF [3,J] 208-A22 WH-18 1 1 A-T77
229-A59 WH-18 REF [5,E]
1 1
A-T1

879-A1 WH-18 A-T28

42 INPUT A (REMOTE START)

REF [5,G] 208-A47 WH-18 REM_STRT
REMOTE START 1 1 REF [13,C] Y983-A5 WH-18 A-T29
INPUT B (LOW COOLANT LEVEL)
43
REF [7,I] A-C4 REF [16,F]
208-A54 WH-18 230-4011
1 1 A-T2

208-A15 WH-16 REF [13,B] Y984-A52 WH-18 A-T74

44 INPUT C (FUEL LEAK)

21
BATT-
F 1 1
45 INPUT D (SPARE) F
REF [13,B] 208-A51 WH-18
1 1
46 INPUT E (SPARE)
BATT-
REF [12,C] 208-A18 WH-18 1 1
47 INPUT F (SPARE)
PROGRAMMABLE INPUTS
STARTER MOTOR 1 1 (NOTE A) 48 INPUT G (SPARE)
REF [7,F] 208-A15 WH-16 BATT-
1 1
49 INPUT H (SPARE)
G S LINK A
REF Sheet_3-[3,J] 208-A48 WH-18 1 1
A-T3

347-A28 WH-18 REF [4,I]

ESTOP_A
1 1
REF [8,G] 208-A56 WH-18 MOT BTRY A-T38
101-A31 RD-8
A-S5
REMOTE ESTOP (OPTIONAL)
NOTE: REMOVE LINKS A&B
G-T2

1 1
A-T4

344-A27 WH-18 REF [10,H] REF [7,F] 229-A59 WH-18 A-T9

15 ANALOG INPUT (GND)

ESTOP_B
101-P1 RD-2 1 1 REF [13,A] P733-A60 WH-18 A-T8

16 ANALOG INPUT A (SPARE)

M LINK B
E 1 1
17 ANALOG INPUT B (SPARE) E
A-T73

229-A53 WH-16 REF [7,G] BATT+

39
A-T

G-T
1

1 1
18 ANALOG INPUT C (SPARE)
F4 SPARE ANALOG INPUT
208-A19 BK-8 422-6095 1 1 (NOTE A) 19 ANALOG INPUT D (SPARE)
BATT+
10A
A-S6

101-A21 WH-14 A-T52 A-T54

108-A23 WH-16 108-A4 WH-16 A-T5
1 1
208-N1 BK-2

26 DSENET B
REF [3,J] 108-A25 WH-18 EXPANSION DATALINK 27 DSENET A
(NOTE A) 28 DSENET SCR
REF [7,I] 108-A55 WH-18

REF Sheet_3-[4,K] 108-A49 WH-18

D 101-R1 BK-2 D
50 RS485 SCR
Battery_1 Battery_2 RS485 CONNECTIONS 51 RS485 B
230-6368 230-6368 (NOTE A)
52 RS485 A
CHARGE ALT

ALT
A-T41
B+ A-T40
101-A43 WH-10

LOW COOLANT LEVEL A-C6

362-2913 155-2267
C C

A A 108-A6 WH-18
B B 208-A18 WH-18 REF [15,G]
C C Y983-A5 WH-18 REF [5,F]

FUEL LEAK SWITCH

A-C7
155-2269

1 Y984-A52 WH-18 REF [5,F]

B 2 208-A51 WH-18 REF [16,F] B

M
A
A-C8 T
L
FUEL LEVEL SENSOR 247-8195 HT
TR

1 1 1E5167A INT-PROP
1E0198W BRAND MARKINGS
1E0013Y CONFIDENTIALITY
2 2 P733-A60 WH-18 REF [9,G] 1E0012A INTERPRETATION
N
O 1E0011 INTPR & TOL
3 3 229-A58 WH-18 REF [5,E] T
E Caterpillar: Confidential Yellow
PROD X OTHER
UNLESS OTHERWISE SPECIFIED VERSION PRIMARY X

A DIMENSIONS ARE IN mm
DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
THIRD ANGLE SHEET 2 OF 6
PROJECTION
DWG CONTROL W591

THE INFORMATION HEREON IS THE PROPERTY OF CATERPILLAR INC. AND/OR ITS

SUBSIDIARIES. WITHOUT WRITTEN PERMISSION, ANY COPYING, TRANSMITTAL TO
OTHERS, AND ANY USE EXCEPT THAT FOR WHICH IT IS LOANED, IS PROHIBITED

DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 - 2X3
02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

L
POWER SCHEMATIC L
CB SHUNT TRIP
STR
352--2951

21 24
22

REF Sheet_2-[10,D] 108-A49 WH-18 A-T69

11 14
A-T70

12

3 PHASE STAR
(6 WIRE) 1200A HARNESS
C2 C1
L1 (U)
L2 (V)
UF-T2

L1-UF1 BK-0 UF-T1

FF-T3 FF-T4

C1-FF1 WH-18 FF-T2

1 1
A-T72

P854-A62 WH-18
K CB1_Y0 CB1_ST+ K
T2
UG-T2

L1-UG1 BK-0 UG-T1 1 1

T1
EXCITER
UH-T2

L1-UH1 BK-0 UH-T1

CB2 OPTIONAL
C2 C1
ABB-T4 ABB-T3
C1-BK ABB-T2
1 1

T5
VF-T2

L2-VF1 BK-0 VF-T1

CB2_Y0 CB2_ST-
T4
VG-T2

L2-VG1 BK-0 VG-T1

T6
VH-T2

L2-VH1 BK-0 VH-T1

CONNECT TO CONNECT TO
ALTERNATOR
WF-T2

L3-WF1 BK-0 WF-T1

BREAKER
WG-T2

L3-WG1 BK-0 WG-T1

C2-BK ABB-T1
1
CB_BATT-
1
A-T71

208-A48 WH-18 REF Sheet_2-[16,E]

E
WH-T2

L3-WH1 BK-0 WH-T1

C2-FF2 WH-18 FF-T1
1 1

J T3 J
NF-T2

N-NF1 BK-0
NF-T1

L3 (W) NG-T2

N-NG1 BK-0
NG-T1

NH-T2
OPTIONAL OPTIONAL
N-NH1 BK-0
NH-T1

CB AUX CONTACTS CB AUX CONTACTS

(1200A) 1 1
(100A TO 800A) 1 1

41 95
41-AX1 WH-16 AX-T7
1 1 95-BK ABB-T21
1 1

PARALLEL STAR 600A/800A HARNESS CB TRIPPED/ 44

1

44
1
98
1

98
1

UNTRIPPED CB TRIPPED/
(12 WIRE) 44-AX2 WH-16 1 1 98-BK 1 1
AX-T1 AX-T6 ABB-T30 ABB-T25

(SY) 41 UNTRIPPED 95
UC-T1

L1-UC1 BK-0 UC-T2

AX-T11 AX-T12
1 1 (SY) ABB-T28 ABB-T29
1 1
L1 (U) 42 96
L2 (V) 42 96
I UE-T1

L1-UE1 BK-0 UE-T2

42-AX3 WH-16 AX-T5
1 1 96-BK ABB-T22
1 1
I
T7 T2
1 1 1 1

EXCITER T1 T8
VC-T1

L2-VC1 BK-0 VC-T2

11 11
11-AX4 WH-16 AX-T2
1 1 11-BK ABB-T24
1 1

T10 T5
VE-T1

L2-VE1 BK-0 VE-T2

CONNECT TO CONNECT TO 1 1 1 1
14 14 14 14
CB OPEN/CLOSED
T4 T11 ALTERNATOR WC-T1

L3-WC1 BK-0 WC-T2

BREAKER (Q/1)
AX-T10

14-AX5 WH-16 AX-T4

1 1
CB OPEN/CLOSED
ABB-T32
14-BK ABB-T23
1 1
11 11
WE-T1

L3-WE1 BK-0 WE-T2

AX-T8 AX-T9
1 1 (Q/1) ABB-T27 ABB-T31
1 1

T12 T6
12 12 12 12
12-AX6 WH-16 AX-T3
1 1 12-BK ABB-T26
1 1
NC-T1

N-NC1 BK-0 NC-T2

NE-T1

N-NE1 BK-0 NE-T2

E T9 T3
H H
L3 (W)

400A HARNESS

1 2
L1-UA1 BK-0 UA-T14

L1

A-T42

A-T43
G G
SERIES STAR 1 2
L2-VA1 BK-0 VA-T2

L2 CUSTOMER LOAD

A-T44

A-T45
(12 WIRE)
1 2
L3-WA1 BK-0 WA-T1

L3
A-T49

A-T46

A-T47
UA-
T6

T2
VA-

T4
A-T50

T1 T5
EXCITER
5+ T4
T8 N-NA1 BK-0 NA-T3

N
T7 T11
E494-A36 WH-18

E495-A35 WH-18

E496-A34 WH-18
E498-A37 WH-18
E498-A38 WH-18
E498-A39 WH-18
200-A63 GN-YL-16 A-T65

F T10
NA-T5
F
A-T
51

T12

GENERATOR GROUND
-6 T9 6310 CONTROLLER
200-A61 GN-YL-16 A-T75

T6

E 41 N/C

T3
CONTROL PANEL DOOR GROUND
E498-A33 WH-16 40 CURRENT SENSING COMMON
A-S1
WA-T3
A-T30
A-T48

E496-A34 WH-18 A-T31

39 CURRENT SENSING L3

E E
E495-A35 WH-18 A-T32

38 CURRENT SENSING L2

NE LINK CABLE
E494-A36 WH-18 A-T33
37 CURRENT SENSING L1
F1
GN/YL GN/YL 7W-0482

GN/YL F434-A17 WH-18 A-T34

2A A-T60

E486-A66 WH-18
A-T57

29 VOLTAGE SENSING L1

MAIN CUSTOMER GROUND

F2
7W-0482

F435-A42 WH-18 A-T35

2A A-T59

E487-A65 WH-18 A-T56

30 VOLTAGE SENSING L2
D D

BASEFRAME
F3
GROUND 7W-0482

F436-A40 WH-18 A-T36

2A A-T58
E488-A64 WH-18 A-T55

31 VOLTAGE SENSING L3

F409-A41 WH-18 A-T37

32 VOLTAGE SENSING N

C C

STANDARD
SHUNT EXCITATION
D350 AVR

6- 3 F-
0V
5+ 6 F+
AI1
CONNECT TO T7 9 4 X1
0V
B CONNECT TO T12 10 2 X2 B
RTD
5 Z1
0V
1 Z2
DI1
0V M
A
T
L
D02 HT
TR

D01
1E5167A INT-PROP
1E0198W BRAND MARKINGS
1E0013Y CONFIDENTIALITY
1E0012A INTERPRETATION
N
O 1E0011 INTPR & TOL
CONNECT TO T1 U 1 U T
E Caterpillar: Confidential Yellow
PROD X OTHER

CONNECT TO T2 V 2 V S1
UNLESS OTHERWISE SPECIFIED VERSION PRIMARY

A DIMENSIONS ARE IN mm
DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
SHEET 3 OF 6
CONNECT TO T3 W 3 W S2
THIRD ANGLE
PROJECTION
DWG CONTROL W591

THE INFORMATION HEREON IS THE PROPERTY OF CATERPILLAR INC. AND/OR ITS

SUBSIDIARIES. WITHOUT WRITTEN PERMISSION, ANY COPYING, TRANSMITTAL TO
OTHERS, AND ANY USE EXCEPT THAT FOR WHICH IT IS LOANED, IS PROHIBITED

DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 - 2X3
02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

L L

ADDITIONAL OPTIONS
OPTIONAL
VFC FOR GENSET RUNNING AND GENERAL FAULT

K K

GFR 6310 CONTROLLER

352-2951
A2 A1
208-GR2 WH-18 R958-GR1 WH-18 OUTPUT E (GENERAL FAULT)
GR-T4 GR-T2 GR-T1
1 1 GR-T3
9
BATT- GR-T5
1 1
14 11
12
24 21
22
J GRR J
352-2951
A2 A1
208-GR3 WH-18 R959-GR4 WH-18 OUTPUT F (GEN RUNNING)
GR-T7 GR-T6
GR-T8
10

14 11
12
24 21
22

I I

OPTIONAL
REMOTE ANNUNCIATOR
2548 CONTROLLER

108-AN1 WH-18 C-T1

1 BTRY -
H H
208-AN2 WH-18 C-T2
2 BTRY +

CBL-AN1 953-AN3 CU-20 C-T3 3 SCREEN

CBL-AN1 951-AN2 WH-18 C-T4

4 A

CBL-AN1 952-AN1 BK-18 C-T5

5 B

G G

120R

2548 CONTROLLER

108-AN1 WH-18 1 BTRY -

AN-T6
1 1 AN-T1

BATT+
1 1
F F
1 1
AN-T7

208-AN2 WH-18 AN-T2 2 BTRY +

BATT-
1 1

CUSTOMER CONNECTIONS: 1 1
AN-T8

CBL-AN1:956-AN3 CU-20 AN-T3

3 SCREEN
SCR
1 1

TO BE CONNECTED IN SERIES 1 1
AN-T9

CBL-AN1:954-AN2 WH-18 AN-T4

4 A
WITH DSENET CIRCUIT A
1 1

1 1
AN-T10

CBL-AN1:955-AN1 BK-18 AN-T5 5 B

B
1 1

E E

D D

C C

B B

M
A
T
L
HT
TR

1E5167A INT-PROP
1E0198W BRAND MARKINGS
1E0013Y CONFIDENTIALITY
1E0012A INTERPRETATION
N
O 1E0011 INTPR & TOL
T
E Caterpillar: Confidential Yellow
PROD X OTHER
UNLESS OTHERWISE SPECIFIED VERSION PRIMARY

A DIMENSIONS ARE IN mm
DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
THIRD ANGLE SHEET 4 OF 6
PROJECTION
DWG CONTROL W591

THE INFORMATION HEREON IS THE PROPERTY OF CATERPILLAR INC. AND/OR ITS

SUBSIDIARIES. WITHOUT WRITTEN PERMISSION, ANY COPYING, TRANSMITTAL TO
OTHERS, AND ANY USE EXCEPT THAT FOR WHICH IT IS LOANED, IS PROHIBITED

DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 - 2X3
02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

L L

ADDITIONAL OPTIONS
OPTIONAL
ALTERNATOR HEATER

AHR
352-2951
K K
REF [16,I] 208-RC36 WH-18 RC-T2 RC-T1

A309-RC35 WH-18 REF [14,H]

A2 A1
21 24 F7
22 190-2558
ALTERNATOR HEATER
HTR-H1 1 1
RC-T12

AC703-RC1 WH-18 RC-T11

11 14
1 AH_L1 12
RC-T10
AC719-RC39 WH-18 RC-T5
6A CF-T4
AC104-CF2 WH-14
1 1
2
F8
1 1 190-2558
AH_L2
HTR-H2 1 1 RC-T13
AC720-RC40 WH-18 RC-T6
6A CF-T3
AC103-CF1 WH-14

J J

OPTIONAL
BATTERY CHARGER

1 1 572-0792
BATTERY_CHARGER
BATT+
1 1 ER-T13
108-ER1 WH-14 ER-T1
OP+
1 1 ER-T12
208-ER2 WH-14 ER-T2

OP-
I BATT- I
REF [16,K] 208-RC36 WH-18 RC-T4
1 1

NC
COM
NO

NTC
NTC_1
6310 CONTROLLER
120R
8 OUTPUT D (GENSET RUNNING) RC-T3
A309-RC35 WH-18 REF [13,K] LK1
H NOTE C LK1_1 H

26 DSENET B ER-T16
CBL-ER1:B-1 GN-18 ER-T6
B
27 DSENET A ER-T17
CBL-ER1:A-2 YL-18 ER-T7

A
28 DSENET SCR ER-T18
CBL-ER1:SCR-3 CU-18 ER-T8

SCR

200-ER46 WH-14 ER-T19

GND_1
AC199-ER45 WH-14 ER-T20

N
1 1 F9 AC102-ER44 WH-14 ER-T21
L
GND 422-6095
G 200-CE3 GN-YL-14 CE-T8
1 1 ER-T26

G
ER-T23
10A ER-T22

1 1

AC199-CE2 WH-14 CE-T7

1 BC_N 1 ER-T25

1 1

BC_L1
AC101-CE1 WH-14 CE-T6
1 1 ER-T24
AC101-ER43 WH-14

F F

AC199-CE2 WH-14 AC199-CD3 WH-12 REF [11,D]

E OPTIONAL E
LOAD CENTER BOX
CE-T13

CD-T3

NEUTRAL
BATT_CHRG_BREAKER
508-6697
20A CE-T18
AC101-CE1 WH-14

ALT_HTRG_BREAKER
577-8557
AC103-CF1 WH-14
L1 CF-T2

CUSTOMER 15A
CF-T1

AC104-CF2 WH-14
D CONNECTION GFCI_RECEPTACLE D
240V 3WIRES 423-7031
GFCI_BREAKER
508-6697
BK (LINE)
L2 20A CD-T2
AC101-CD1 WH-12 CD-T4

WH (N) CD-T5
AC199-CD3 WH-12 REF [14,E]
JWH_BREAKER
577-8557
CONNECT
JACKET WATER GND
CD-T6

15A
HEATER WIRES
200-CE3 GN-YL-14 200-CD2 GN-YL-10
CE-T11

CD-T1

GROUND GFCI RECEPTACLE

CD-T8

C C
200-CD4 GN-YL-10
CD-T7

MAIN CUSTOMER
GROUND

B B

M
A
T
L
HT
TR

1E5167A INT-PROP
1E0198W BRAND MARKINGS
1E0013Y CONFIDENTIALITY
1E0012A INTERPRETATION
N
O 1E0011 INTPR & TOL
T
E Caterpillar: Confidential Yellow
PROD X OTHER
UNLESS OTHERWISE SPECIFIED VERSION PRIMARY

A DIMENSIONS ARE IN mm
DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
THIRD ANGLE SHEET 5 OF 6
PROJECTION
DWG CONTROL W591

THE INFORMATION HEREON IS THE PROPERTY OF CATERPILLAR INC. AND/OR ITS

SUBSIDIARIES. WITHOUT WRITTEN PERMISSION, ANY COPYING, TRANSMITTAL TO
OTHERS, AND ANY USE EXCEPT THAT FOR WHICH IT IS LOANED, IS PROHIBITED

DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 - 2X3
02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

L ADDITIONAL INFORMATION - COMPONENT DETAILS & CUSTOMER CONNECTIONS L

MAIN CUSTOMER RAIL

CIRCUIT BREAKER RAIL
(OPTIONS INCLUDED)
K

FUSE ID CURRENT RATING WIRE ID DESCRIPTION

(OPTIONS INCLUDED) K

F4 10A 101, 108 PANEL SUPPLY

F5 25A 101, 105 ECM POWER
F6 2A 148, 101 ENCLOSURE LIGHTS

DC FUSES

J J

GROUND FAULT

F1 F2 F3 F4 F5 F6 STR GFR GRR ELR

REM_STRT
CLN_GND

ESTOP_A

ESTOP_B

CAN_SH
BATT +

BATT +

CB2_95

CB2_96

CB2_98
BATT -

BATT -

BATT -

CB1_14

CB2_11

CB2_12

CB2_14
CB1_11

CB1_12

CB1_95
CB1_41
CB1_96
CB1_42
CB1_98
CB1_44
CAN +

CAN -
C1 C1 C2 C2
I I

H H

TERMINAL ID WIRE ID DESCRIPTION

CB1_ST+ C1 CB1 SHUNT TRIP
CB2_ST+ C1 CB2 SHUNT TRIP
BATT- C2 BATTERY NEGATIVE
AC FUSES CUSTOMER TERMINALS RELAY VFC CONNECTIONS GROUND FAULT RELAY 11 11 CB1 AUX COM
12 12 CB1 AUX NO
14 14 CB1 AUX NC
FUSE ID CURRENT RATING WIRE ID DESCRIPTION TERMINAL ID WIRE ID DESCRIPTION RAIL CURRENT RATING DESCRIPTION 95/41 95/41 CB1 AUX COM
F1 2A F434, E486 CLN_GND 229 CLEAN GROUND FOR ANALOG INPUTS STR 8A SHUNT TRIP RELAY
L1 SENSING AC 96/42 96/42 CB1 AUX NO
F2 2A F435, E487 REM_STRT 879 REMOTE START INPUT GFR 8A GENERAL FAULT RELAY
G L2 SENSING AC 98/44 98/44 CB1 AUX NC G
F3 2A F436, E488 BATT - 208 BATTERY NEGATIVE GRR 8A GENSET RUNNING RELAY
L3 SENSING AC 11 11 CB2 AUX COM
BATT - 208 BATTERY NEGATIVE ELR 8A ENCLOSURE LIGHTS RELAY 12 12 CB2 AUX NO
BATT - 208 BATTERY NEGATIVE
14 14 CB2 AUX NC
ESTOP_A 347 ECM ESTOP INPUT 95 95 CB2 AUX COM
ESTOP_B 344 GENSET CONTROLLER ESTOP INPUT 96 96 CB2 AUX NO
BATT + 108 BATTERY POSITIVE (10A FUSED) 98 98 CB2 AUX NC
BATT + 108 BATTERY POSITIVE (10A FUSED)
CAN + Y797 CAN + COMMS
CAN - Y798 CAN - COMMS
CAN SH Y799 CAN SH COMMS

F F

SHORE POWER RAIL

(OPTIONS INCLUDED)
E E

10A UL BATTERY CHARGER

D D
F7 F8 F9
AHR
BC_L1
AH_L1

AH_L2

BC_N
GND

C C

B COMPONENT DESCRIPTION B
AHR ALTERNATOR SPACE HEATER RELAY
AH_L1 ALTERNATOR HEATER AC SUPPLY L1
AH_L2 ALTERNATOR HEATER AC SUPPLY L2
F7 ALTERNATOR HEATER FUSE L1 (6A)
F8 ALTERNATOR HEATER FUSE L2 (6A) M
A
GND SHORE POWER GROUND T
L
HT
F9 BATTERY CHARGR FUSE L1 (10A) TR

BC_L1 BATTERY CHARGER AC SUPPLY L1

1E5167A INT-PROP
BC_N BATTERY CHARGER AC SUPPLY N 1E0198W BRAND MARKINGS
1E0013Y CONFIDENTIALITY
1E0012A INTERPRETATION
N
O 1E0011 INTPR & TOL
T
E Caterpillar: Confidential Yellow
PROD X OTHER
UNLESS OTHERWISE SPECIFIED VERSION PRIMARY

A DIMENSIONS ARE IN mm
DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
THIRD ANGLE SHEET 6 OF 6
PROJECTION
DWG CONTROL W591

THE INFORMATION HEREON IS THE PROPERTY OF CATERPILLAR INC. AND/OR ITS

SUBSIDIARIES. WITHOUT WRITTEN PERMISSION, ANY COPYING, TRANSMITTAL TO
OTHERS, AND ANY USE EXCEPT THAT FOR WHICH IT IS LOANED, IS PROHIBITED

DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 - 2X3
02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1