KAOHSIUNG HITACHI

ELECTRONICS CO.,LTD
P.O. BOX 26-27
2,13TH EAST ST. K.E.P.Z.
KAOHSIUNG TAIWAN R.O.C.
TEL:(07) 821-5811(7 LINE)
FAX:(07) 821-5815

FOR MESSRS: DATE: Mar.06,2009

CUSTOMER’S ACCEPTANCE SPECIFICATIONS

SP14Q006
CONTENTS

No. ITEM SHEET No. PAGE

1 COVER 7B64PS 2701- SP14Q006-7 1-1/1
2 RECORD OF REVISION 7B64PS 2702- SP14Q006-7 2-1/2~2/2
3 GENERAL SPECIFICATION 7B64PS 2703- SP14Q006-7 3-1/1
4 ABSOLUTE MAXIMUM RATINGS 7B64PS 2704- SP14Q006-7 4-1/1
5 ELECTRICAL CHARACTERISTICS 7B64PS 2705- SP14Q006-7 5-1/2~2/2
6 OPTICAL CHARACTERISTICS 7B64PS 2706- SP14Q006-7 6-1/3~3/3
7 BLOCK DIAGRAM 7B64PS 2707- SP14Q006-7 7-1/1
8 INTERFACE TIMING CHART 7B64PS 2708- SP14Q006-7 8-1/3~3/3
9 OUTLINE DIMENSIONS 7B63PS 2709- SP14Q006-7 9-1/2
7B64PS 2709- SP14Q006-7 9-2/2
10 APPEARANCE STANDARD 7B64PS 2710- SP14Q006-7 10-1/3~3/3
11 PRECAUTION IN DESIGN 7B64PS 2711- SP14Q006-7 11-1/2~2/2
12 DESIGNATION OF LOT MARK 7B64PS 2712- SP14Q006-7 12-1/1
13 PRECAUTION FOR USE 7B64PS 2713- SP14Q006-7 13-1/1

 When products will be discontinued , customers will be informed by HITACHI with

twelve months prior announcement.

ACCEPTED BY; PROPOSED BY;

KAOHSIUNG HITACHI Sh.

7B64PS 2701- SP14Q006-7 PAGE 1-1/1
ELECTRONICS CO.,LTD. No.
 RECORD OF REVISION

DATE SHEET No. SUMMARY

Jan.16,’03 7B64PS 2705 - 5.2 ELECTRICAL CHARACTERISTICS OF LED BACKLIGHT
SP14Q006-2
Page 5-2/2 SYMBOL TYP. MAX
VLED (TBD) -
ILED 60 -
Revised↓
SYMBOL TYP. MAX
VLED 5 5.2
ILED 160 -

Oct.22,’03 7B64PS 2709 - Changed LED I/F :

SP14Q006-3 JAE/ 1L-G-4S-S3C2 →JAE/ IL-G-4S-S3C2
Page 9-2/2
Mar.24,’04 7B64PS 2708 - 8.3 POWER ON/OFF TIMING SEQUENCE
SP14Q006-4 Revised tDLD min. 200 → 50
Page 8-3/3 Revised tCH max. 200 → 30
Jun.04,’04 7B64PS 2705- 5.1 ELECTRICAL CHARACTERISTICS
Added
SP14Q006-5
ITEM SYMBOL MIN. TYP. MAX
Page 5-1/2
Power Supply Voltage Logic VDD-VSS 3.2 3.3 3.4
21.0 22.0 23.0
Recommend LC Driving Voltage VDD-V0 20.0 21.0 22.0
19.0 20.0 21.0

7B64PS 2706- 6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT

Added The LCD driving voltage should be adjusted at the
SP14Q006-5
voltage where the peak contrast is obtained.
Page 6-3/3

7B64PS 2710- 10.1 APPEARANCE INSPECTION CONDITION

Revised 45°25°
SP14Q006-5
Page 10-1/3
Jul.13,’07 7B64PS 2703- 3. GENERAL SPECIFICATIONS
Added
SP14Q006-6
Page 3-1/1 (11) Backlight Type LED(Color : white)
↓
(11) Backlight Type LED(Color : white)
Life time : 40Kh @ 25℃
Note : Life time for half of initial brightness

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2702- SP14Q006-7 PAGE 2-1/2
ELECTRONICS CO.,LTD. No.
 RECORD OF REVISION

DATE SHEET No. SUMMARY

Jul.13,’07 7B64PS 2705- 5.2 ELECTRICAL CHARACTERISTICS OF LED BACKLIGHT
Revised
SP14Q006-6

allowable forward current

Page 5-2/2

(mA/pcs)
→

Ambient Temperature(℃)

7B64PS 2712- 12. DESIGNATION OF LOT MARK

Added
SP14Q006-6
REV No. ITEM
Page 12-1/1
- -
A Backlight life time : 40kh
Mar.06,’09 7B64PS 2712- 12. DESIGNATION OF LOT MARK
SP14Q006-7 Revised reversion from REV. A to REV.B
Page 12-1/1

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2702- SP14Q006-7 PAGE 2-2/2
ELECTRONICS CO.,LTD. No.
3. GENERAL SPECIFICATIONS

(1) Part Name SP14Q006

(2) Outer Dimensions 167.0(W)mm×109.0(H)mm×10.0 (D) mm max.

(3) Effective Area 120(W)mm min. × 89(H)mm min.

(4) Dot Size 0.345(W)min. × 0.345(H)min.

(5) Dot Pitch 0.360(W)mm × 0.360(H)mm

(6) Dot Number (Resolution) 320 (W) × 240 (H) dots

(7) Duty Ratio 1/240

(8) LCD Type Transmissive type F-B / W STN

With anti-glare type upper polarizer

(9) Viewing Direction 6 O’clock

Viewing Angle in Rear - Front
(10) Viewing Angle (12:00) (6:00)
R-F=90 °(typ.)

(11) Backlight Type LED(Color : white)

Life time : 40Kh @ 25℃

Note : Life time for half of initial brightness

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2703- SP14Q006-7 PAGE 3-1/1
ELECTRONICS CO.,LTD. No.
4. ABSOLUTE MAXIMUM RATINGS
4.1 ELECTRICAL ABSOLUTE MAXIMUM RATINGS VSS=0V : STANDARD
ITEM SYMBOL MIN. MAX. UNIT COMMENT
Power Supply for Logic VDD-VSS 0 6.0 V
Power Supply for LC Driving VDD-VEE 0 27.5 V
Input Signal Voltage Vi -0.3 VDD+0.3 V (Note 1)
Static Electricity VESD0 - ±100 V (Note 2,3,4)
VESD1 - ±10 kV (Note 2,3,5)

Note 1 : DOFF , FLM , CL1 , CL2 , D0~D3.

Note 2 : Make certain you are grounded when handling LCM.

Note 3 : Energy storage capacitance 200pF , discharge resistance 250Ω Ta=25℃ , 60%RH.

Note 4 : Contact discharge to I/F connector pins.

Note 5 : Contact discharge to front metal bezel.

4.2 ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS

ITEM OPERATING STORAGE COMMENT
MIN. MAX. MIN. MAX.
Ambient Temperature -20℃ 70℃ -30℃ 80℃ (Note 2,3,6)
Humidity (Note 1) (Note 1) Without Condensation
2 2
2.45m/s 11.76m/s
Vibration - (0.25G) - (1.2G) (Note 4)1h max.
(Note 5)
2
29.4m/s 490.0m/s2
Shock - (3 G) - (50 G) X、Y、Z Directions
(Note 5)
Corrosive Gas Not Acceptable Not Acceptable

Note 1 : Ta≦40℃ : 85%RH max.

Ta＞40℃ : Absolute humidity must be lower than the humidity of 85%RH at 40℃

Note 2 : Ta at -30℃ - - -＜ 48h , at 80℃ - - -＜ 168h.

Note 3 : Background color changes slightly depending on ambient temperature.

This phenomenon is reversible.
Note 4 : 5Hz~100Hz (Except resonance frequency)

Note 5 : This module should be operated normally after finish the test.

Note 6 : The response time will be slower under low temperature.

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2704- SP14Q006-7 PAGE 4-1/1
ELECTRONICS CO.,LTD. No.
5. ELECTRICAL CHARACTERISTICS
5.1 ELECTRICAL CHARACTERISTICS
I T E M SYMBOL CONDITION MIN. TYP. MAX. UNIT COMMENT
Power Supply Voltage 4.75 5.0 5.25
VDD-VSS - V
for Logic 3.2 3.3 3.4
Power Supply Voltage
VEE-VSS - -23.1 -22.0 -20.9 V
for LC Driving
H LEVEL 0.8VDD - VDD V
Input Signal Voltage Vi (Note1)
L LEVEL 0 - 0.2VDD V
Power Supply Current VDD-VSS=5.0V
IDD - 6.0 - mA (Note2)
for Logic VEE-VSS= -22.0V
Power Supply Current VDD-VSS=5.0V
IEE - 5.0 - mA (Note2)
for LC Driving VEE-VSS= -22.0V
Ta= 0℃ ,  = 0∘ 21.0 22.0 23.0 V
Recommended LC
VDD-V0 Ta=25℃ ,  = 0∘ 20.0 21.0 22.0 V (Note3)
Driving Voltage
Ta=50℃ ,  = 0∘ 19.0 20.0 21.0 V
Frame Frequency fFLM - 70 75 80 Hz (Note4)

Note 1 : DOFF , FLM , CL1 , CL2 , D0~D3.

Note 2 : FLM=75Hz , test pattern is all “Q”.

VDD-V0=21.0V , Ta=25℃

Note 3 : Recommended LC driving voltage may fluctuate about ±1.0V by each module.
Test pattern is all “Q”

Note 4 : Please set the frame frequency so as to avoid flicker and rippling on the display.

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2705- SP14Q006-7 PAGE 5-1/2
ELECTRONICS CO.,LTD. No.
 5.2 ELECTRICAL CHARACTERISTICS OF LED BACKLIGHT

ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT COMMENT

Power Supply Voltage
VLED - - 5.0 5.2 V -
for LED
Power Supply Current
ILED VLED=5.0V - 160 - mA (Note 1)
for LED

Note 1 : The ILED changes depending on ambient temperature.

allowable forward current
(mA/pcs)

Ambient Temperature(℃)

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2705- SP14Q006-7 PAGE 5-2/2
ELECTRONICS CO.,LTD. No.
Note 4 : Definition of optical response

Non-selective state Selective state Non-selective state

Brightness

100% 10%
90%

tr tf
Rise time Fall time

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2706- SP14Q006-7 PAGE 6-2/3
ELECTRONICS CO.,LTD. No.
 6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT

I T E M MIN. TYP. MAX. UNIT NOTE

Brightness - 150 - cd/m2 ILED=160mA
Brightness Uniformity - - ±30 % Note 1

Ta=25℃, Display data should be all “ON”.

The LCD driving voltage should be adjusted at the voltage where
the peak contrast is obtained.

Note 1 : Measure of the following 9 places on the display.

Y=80 Y=160 Y=240

X=60

X=120

X=180

Definition of the brightness tolerance.

( Max. or Min. Brightness - Average Brightness

Average Brightness
) x 100

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2706- SP14Q006-7 PAGE 6-3/3
ELECTRONICS CO.,LTD. No.
 D0~D3
CL2

KAOHSIUNG HITACHI
IC1 IC2 IC4

ELECTRONICS CO.,LTD.
7. BLOCK DIAGRAM

Y1
FLM

Y80
Y81
Y160
Y241
Y320

CL1


X1
X1

DATE Mar.06,’09
IC5 D3 D2 D1 D0
X80

Sh.
No.
DOFF
X81
IC6
320×240 dots
X160

X161

IC7
X240
X240

VDD

7B64PS 2707- SP14Q006-7

VSS POWER
 : TIMING CIRCUIT
V0 SUPPLY
VEE

VLED(+)
LED Back Light

PAGE 7-1/1
VLED(-)
8. INTERFACE TIMING CHART
8.1 INTERFACE TIMING CHART

52.1s≦T≦59.5s

CL1

CL2
X240 X1 X2

D3 Y1 Y5 Y317

D2 Y2 Y6 Y318

D1 Y3 Y7 Y319

D0 Y4 Y8 320

FLM

CL1
240×T

FLM

D0~D3 X1 X2 X239 X240

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2708- SP14Q006-7 PAGE 8-1/3
ELECTRONICS CO.,LTD. No.
8.2 TIMING CHARACTERISTICS

ITEM SYMBOL MIN. TYP. MAX. UNIT

CL2 frequency fCP - - 6.5 MHz
CL2 pulse width tw 45 - - ns
CL2 rise, fall time tr,tf - - 15 ns
Data set up time tDSU 30 - - ns
Data hold time tDHD 30 - - ns
CL1 set up time tLSU 80 - - ns
CL1 clock time tLC 120 - - ns
“FLM” set up time tSETUP 100 - - ns
“FLM” hold time tHOLD 100 - - ns
“CL1” pulse width twc 125 - - ns

tw tw tw
tf tr

0.8VDD 0.8VDD 0.8VDD 0.8VDD

CL2 0.2VDD 0.2VDD 0.2VDD 0.2VDD

tDSU tDHD

0.8VDD 0.8VDD 0.8VDD 0.8VDD

D0~D3 0.2VDD 0.2VDD 0.2VDD 0.2VDD

tLSU tLC
0.8VDD 0.8VDD
CL1 0.2VDD 0.2VDD

twc

tSETUP tHOLD

0.8VDD 0.8VDD
FLM

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2708- SP14Q006-7 PAGE 8-2/3
ELECTRONICS CO.,LTD. No.
8.3 POWER ON/OFF TIMING SEQUENCE
tDLD tDLD

VDD
tCH tCH
GND
0.8VDD 0.8VDD
SIGNAL
GND tDLCr tDLCf

VEE GND

tDLCs tDLCs

0.8VDD 0.8VDD
DOFF
0.2VDD 0.2VDD
GND tLDH tLDH
tDOr tDOf

SYMBOL MIN. MAX. UNIT COMMENT

tDLD 50 - ms
tCH 0 30 ms (Note 1)
tLDH 0 - ms
tDOr - 100 ns
tDOf - 100 ns
tDLCr 0 - ms (Note 2)
tDLCf 0 - ms
tDLCs 20 - ms
Note 1 : Please keep the specified sequence because wrong
sequence may cause permanent damage to the LCD panel.
Note 2 : HITACHI recommends you to use DOFF function.
Display quality may deteriorate if you don‘t use DOFF function.

8.4 POWER SUPPLY FOR LCM (EXAMPLE)

VDD +5.0V

5.0V

LCM VSS

V0 VR 22.0V
VEE
-22.0V
Note 1 : VR : 10k

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2708- SP14Q006-7 PAGE 8-3/3
ELECTRONICS CO.,LTD. No.
9.2 DISPLAY PATTERN
115.185 (320 dots)

0.345
0.36
86.385 (240 dots)

0.345 Scale : NTS

0.36 Unit : mm
Measurement Tolerance : ±0.1
9.3 INTERFACE PIN CONNECTION
FPC：pitch 1.25mm 14 pins
INTERFACE PIN No. SIGNAL LEVEL FUNCTION
LCM CN1 1 D0 H/L Display Data
2 D1
3 D2
4 D3
5 DOFF H/L H : ON / L : OFF
6 FLM H First Line Marker
7 N.C - -
8 CL1 HL Data Latch
9 CL2 HL Data Shift
10 VDD - Power Supply for Logic
11 VSS - GND
12 VEE - Power Supply for LC
13 V0 - Operating Voltage LC Driving
14 VSS - GND

INTERFACE PIN No. SIGNAL LEVEL FUNCTION

LCM CN2 1 VLED(+) - Power Supply for LED
2 N.C - -
3 N.C - -
4 VLED(-) - LED GND
LED I/F : J.A.E / IL – G - 4S – S3C2-SA

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2709- SP14Q006-7 PAGE 9-2/2
ELECTRONICS CO.,LTD. No.
10. APPEARANCE STANDARD
10.1 APPEARANCE INSPECTION CONDITION

Visual inspection should be done under the following condition.

(1) The inspection should be done under in the dark room.
(2) The CFL should be lighted with the prescribed inverter.
(3) The distance between eyes of an inspector and the LCD module is 25cm.
(4) The viewing zone is shown the figure .
Viewing angle ≦25°

eye eye
25° 25°
LCD
Bezel

10.2 DEFINITION OF EACH ZONE

A zone : Within the effective area specified at page 9-1/2 of this document.
B zone : Area between the window of metal frame and the effective area line
specified at page 9-1/2 of this document.

Effective Area

Window of Metal Frame

A zone
B zone

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2710- SP14Q006-7 PAGE 10-1/3
ELECTRONICS CO.,LTD. No.
10.3 APPEARANCE SPECIFICATION
*) If a problem occurs in respect to any of these items ,
both parties(Customer and HITACHI) will discuss in more detail.

No. ITEM CRITERIA A B

Scratches Distinguished one is not acceptable  -
(To be judged by HITACHI limit sample)
Dent Same as above  -
Wrinkles in Polarizer Same as above  -
Bubbles Average Diameter Maximum Number
D(mm) Acceptable
D≦0.2 Ignore
0.2＜D≦0.3 12 ○ -
0.3＜D≦0.5 3
0.5＜D None
Stains, Filamentous
Foreign Materials, Length Width Maximum Number ○ -
Dark Spot L(mm) W(mm) Acceptable
L≦2.0 W≦0.03 Ignore
L≦3.0 0.03＜W≦0.05 6
L L≦2.5 0.05＜W≦0.1 1
Round
Average Diameter Maximum Number Minimum
D(mm) Acceptable Space
C
D＜0.2 Ignore - ○ -
0.2 ≦D＜0.33 8 10mm
0.33≦D None -
D Total Filamentous + Round = 10
Those wiped out easily are acceptable ○ ○
Color Tone To be judged by HITACHI limit sample ○ -
Color Uniformity Same as above ○ -
Pinhole Average Diameter Maximum Number
D(mm) Acceptable
D≦0.15 Ignore
0.15＜D≦0.3 10
C≦0.015 Ignore
Contrast Average Contrast Maximum Minimum ○ -
Irregularity Diameter Number Space
(Spot) D(mm) Acceptable
D≦0.25 To be Ignore -
0.25＜D≦0.35 judged by 10 20mm
0.35＜D≦0.5 HITACHI 4 20mm
0.5 ＜D None -

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2710- SP14Q006-7 PAGE 10-2/3
ELECTRONICS CO.,LTD. No.
11. PRECAUTION IN DESIGN
11.1 LC DRIVING VOLTAGE (VEE) AND VIEWING ANGLE RANGE
Setting VEE out of the recommended condition will be a cause for a change of
viewing angle range.

11.2 PRECAUTIONS AGAINST STATIC CHARGE

As this module contains C-MOS LSIs , it is not strong against electrostatic discharge.
Make certain that the operator’s body is connected to the ground through a list
band etc. And don’t touch I/F pins directly.

11.3 POWER ON SEQUENCE

Input signals should not be applied to LCD module before power supply voltage is
applied and reaches to specified voltage (VDD).
If above sequence is not kept, C-MOS LSIs of LCD modules may be damaged due
to latch up problem.

11.4 PACKAGING
(1) No leaving product is preferable in the place of high humidity for a long period of
time. For their storage in the place where temperature is 35 ℃ or higher ,special care
to prevent them from high humidity is required. A combination of high temperature and
high humidity may cause them polarization degradation as well as bubble generation
and polarizer peel-off. Please keep the temperature and humidity within the specified
range for use and storage.

(2) Since polarizers tend to be easily damaged, They should be handled full
with care so as not to get them touched, pushed or rubbed.

(3) As the adhesives used for adhering polarizers are made of organic substances
which will be deteriorated by a chemical reaction with such chemicals as acetone, toluene ,
ethanol and isopropyl alcohol. The following solvents are recommended for use:
normal hexane

Please contact us when it is necessary for you to use chemicals.

(4) Lightly wipe to clean the dirty surface with absorbent cotton waste or other soft
material like chamois , soaked in the chemicals recommended without scrubbing it
hardly. To prevent the display surface from damage and keep the appearance in good
state, it is sufficient, in general, to wipe it with absorbent cotton.

(5) Immediately wipe off saliva or water drop attached on the display area because its
long period adherence may cause deformation or faded color on the spot.

(6) Foggy dew deposited on the surface due to coldness will be caused for polarizer
damage, stain and dirt on product. When necessary to take out the products from
some place at low temperature for test, etc. It is required for them to be warmed
up in a container once at the temperature higher than that of room.

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2711- SP14Q006-7 PAGE 11-1/2
ELECTRONICS CO.,LTD. No.
 (7) Touching the display area and contact terminals with bare hands and contaminating
them are prohibited, because the stain on the display area and poor insulation
between terminals are often caused by being touched by bare hands.
(Some cosmetics are detrimental to polarizers.)

(8) In general the quality of glass is fragile so that it tends to be cracked or chipped in
handling, specially on its periphery. Be careful not to give it sharp shock caused by
dropping down, etc.

11.5 CAUTION FOR OPAERATION

(1) It is an indispensable condition to drive LCDs within the specified voltage limit since
the higher voltage than the limit causes the shorter LCD life. An electrochemical
reaction due to direct current causes LCDs undesirable deterioration , so that the use
of direct current driver should be avoided.

(2) Response time will be extremely delayed at lower temperature than the operating
temperature range and on the other hand at higher temperature LCDs show dark blue
color in them. However those phenomena do not mean malfunction or out of order
with LCDs which will come back in the specified operating temperature range.

(3) If the display area is pushed hard during operation, some font will be abnormally
displayed but it resumes normal condition after turning off once.

(4) A slight dew depositing on terminals is a cause for electrochemical reaction resulting
in terminal open circuit. Please operate the LCD module under the relative condition of
40℃ 85%RH.

11.6 STORAGE
In case of storing for a long period of time (for instance , for years) for the purpose of
replacement use , the following ways area recommended.
(1) Storage in a polyethylene bag with the opening sealed , so the fresh air will not
be entered from outside .
(2) Placing in a dark place where neither exposure to direct sunlight nor light is , keeping
temperature in the range from 0 ℃ to 35 ℃.

(3) Storing with no touch on polarizer surface by anything else. (It is recommended to
store them as they have been contained in the inner container at the time of delivery
from us.)

11.7 SAFETY
(1) It is recommendable to crash damaged or unnecessary LCDs into pieces and wash
off liquid crystal by either of solvents such as acetone and ethanol , which should be
burned up later.

(2) When any liquid leaked out of a damaged glass cell comes in contact with your
hands , please wash it off well with soap and water.

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2711- SP14Q006-7 PAGE 11-2/2
ELECTRONICS CO.,LTD. No.
 12. DESIGNATION OF LOT MARK
12.1 LOT MARK
Lot mark is consisted of 5 digits for production lot and
6 digits for production control.
Year Figure in
8 0 4 1 T lot mark
2009 9
Digits for production control
2010 0
T : Made in Taiwan 2011 1
Week 2012 2
Month 2013 3
Year

Figure in Figure in Week Figure in

Month Month
lot mark lot mark (day in calendar) lot mark
Jan. 01 Jul. 07 1~ 7 1
Feb. 02 Aug. 08 8~14 2
Mar. 03 Sep. 09 15~21 3
Apr. 04 Oct. 10 22~28 4
May 05 Nov. 11 29~31 5
Jun. 06 Dec. 12

12.2 SERIAL No.

Serial No. is consisted of 6 digits number (000001~999999).

12.3 LOCATION OF LOT MARK

Label is bring attached on the back side of module.

12.4 REVISION(Rev.) CONTROL

Rev No. ITEM

Backlight life time : 40kh
A Mcount IC :MN73099HED(Panasonic)
Transistor :2SA1036K(ROHM)
Backlight life time : 40kh
B Mcount IC :IT7001M(ITE)
Transistor :2SA1576(ROHM)

SP14Q006 B

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2712- SP14Q006-7 PAGE 12-1/1
ELECTRONICS CO.,LTD. No.
13. PRECAUTION FOR USE
13.1 A limit sample should be provided by the both parties on an occasion when the both
parties agreed its necessity. Judgment by a limit sample shall take effect after the
limit sample has been established and confirmed by the both parties.

13.2 On the following occasions, the handling of the problem should be decided through
discussion and agreement between responsible persons of the both parties.

(1) When a question is arisen in the specifications.

(2) When a new problem is arisen which is not specified in this specifications.

(3) When an inspection specifications change or operating condition change in customer

is reported to HITACHI, and some problem is arisen in this specification due to the
change.

(4) When a new problem is arisen at the customer’s operating set for sample evaluation
in the customer site.

The precaution that should be observed when handling LCM have been explained
above. If any points are unclear or if you have any request , please contact HITACHI.

KAOHSIUNG HITACHI Sh.

DATE Mar.06,’09 7B64PS 2713- SP14Q006-7 PAGE 13-1/1
ELECTRONICS CO.,LTD. No.