CAMPUS® Datasheet

Bakelite® PF 6507 - PF-(CF+X)

Bakelite GmbH

Product Texts

Product description:
Phenolic moulding compound, inorganically filled, glass fibre reinforced, elastomer modified, galvanizable, heat resistant, good media
resistance, high dimensional stability at raised temperature, high mechanical strength.

Application areas:
Thermally and mechanically highly stressed parts in automotive field, solenoid switch caps, electrical motor end shields.

Property Name Value Unit Standard No.

Apparent density (moulding compound) 0.7 g/cm³ ISO 60
Moulding shrinkage (injection moulding, longitudinal) 0.2 % ISO 2577
Post shrinkage (injection moulding, 168h/110°C) 0.1 % ISO 2577
Tensile strength (5mm/min) 85 MPa ISO 527-1/2
Compr. strength (test spec. flat tested) 180 MPa ISO 604
Flexural strength (2mm/min) 135 MPa ISO 178
Flexural modulus 10000 MPa ISO 178
Ball indentation hardness (H 961/30) 250 MPa ISO 2039/P1
Water absorption (24h/23°C) 15 mg similar to ISO 62
Preparation of Test Specimens of Thermosetting Moulding Compound

Compression to ISO 295

Injection to ISO 10724

Storage capability
2 years (relative humidity of 50-60% and maximum storage temperature of approximately 20°C)

Rheological properties Value Unit Test Standard

Molding shrinkage, parallel 0.2 % ISO 294-4, 2577

Mechanical properties Value Unit Test Standard

Tensile modulus 11000 MPa ISO 527-1/-2
Charpy impact strength, +23°C 15 kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 3.5 kJ/m² ISO 179/1eA

Thermal properties Value Unit Test Standard

Temp. of deflection under load, 8.00 MPa 170 °C ISO 75-1/-2

Electrical properties Value Unit Test Standard

Relative permittivity, 100Hz 6.5 - IEC 62631-2-1
Dissipation factor, 100Hz 0.1 E-4 IEC 62631-2-1
Volume resistivity 1E10 Ohm*m IEC 62631-3-1
Surface resistivity 1E11 Ohm IEC 62631-3-2
Electric strength 22.5 kV/mm IEC 60243-1
Comparative tracking index 150 - IEC 60112

Last update: 2022-07-13 Source: https://www.campusplastics.com Page: 1/4

Bakelite® PF 6507 - PF-(CF+X)
Bakelite GmbH

Other properties Value Unit Test Standard

Density 1600 kg/m³ ISO 1183

Test specimen production Value Unit Test Standard

Injection molding, injection temperature 115 °C ISO 10724
Injection molding, injection velocity 170 mm/s ISO 10724
Injection molding, hold pressure 100 MPa ISO 10724
Injection molding, cure time 25 min ISO 10724
Compression molding, mold temperature 160 °C ISO 295
Compression molding, cure time 1 min ISO 295

Diagrams

Dynamic shear modulus-temperature Stress-strain

Dynamic shear modulus-temperature Stress-strain
Bakelite® PF 6507 Bakelite® PF 6507

1E4
100 23 °C
B
80 °C
120 °C
Shear modulus in MPa

80
B - Break

B
Stress in MPa 60 B

40

www.campusplastics.com
1E3
-100 0 100 200 300
20

Temperature in °C

www.campusplastics.com
0
0 0.2 0.4 0.6 0.8 1

Strain in %

Last update: 2022-07-13 Source: https://www.campusplastics.com Page: 2/4

Bakelite® PF 6507 - PF-(CF+X)
Bakelite GmbH

Secant modulus-strain
Secant modulus-strain
Bakelite® PF 6507

14000 23 °C
80 °C
120 °C
13000
B - Break
Secant modulus in MPa

12000

11000
B

10000

B
9000

B
www.campusplastics.com
8000
0 0.2 0.4 0.6 0.8 1

Strain in %

Characteristics

Processing Regional Availability

Injection Molding, Transfer Molding North America, Europe, Asia Pacific, South and Central America,
Near East/Africa

Other text information

Injection molding
VERARBEITUNG
Temperature of material: 80 - 100 °C
Mould temperature: 160 - 190 °C
Curing time: 10-20 sec

Further Information:
Barrel temperature
- Feed zone: 60-75 °C
- Nozzle zone: 80-100 °C
Cavity moulding pressure: >15 MPa
Back pressure: 0.5-2 MPa
Holding pressure: 60% of injection pressure

Compression molding
PROCESSING
Mould temperature: 160-190 °C
Curing time: 20-40 sec
Cavity moulding pressure: >15 MPa

Bakelite Synthetics
Gennaer Str. 2 - 4
58642 Iserlohn - Letmathe, Germany

Last update: 2022-07-13 Source: https://www.campusplastics.com Page: 3/4

Bakelite® PF 6507 - PF-(CF+X)
Bakelite GmbH

E-mail: michael.stahl@bakelite.com

----------------------------------------------------------------------

Important Information

As international harmonization of testing procedures progresses, previously used national standards are increasingly being replaced by ISO
(DIN EN ISO) standards. All information, recommendations and suggestions provided by Bakelite AG in the form of verbal or written
communication, or in pertinent data bases, represent our best knowledge and experience. Such data are non-binding in character, and do
not represent, either explicitly or implicitly, assurances or a guarantee of specific properties. The specified parameters merely represent
typical data; they do not form a basis for either a guarantee or a specification. The information, recommendations and suggestions we
provide describe our products and possible applications in general or exemplary terms; they do not relate to specific cases. The process of
constant continued development and improvement of our products can lead to changes in pertinent parameters, texts and illustrations; no
special mention is made of possible alterations. Our technical advice does not free the customer of its responsibility to verify our current
information, in particular our technical data sheets, safety data sheets and technical information leaflets.

The customer will conduct its own tests of our products to determine their suitability for the intended processes and uses, as well as to
establish that their processing properties are appropriate in the pertinent situation, since our products may be used in a wide range of
technical applications that involve very different requirements according to the specific situation. Therefore, such specific cases are outside
our control, and are the exclusive responsibility of the customer. A pertinent agreement is necessary in case a binding assurance of specific
parameters is required. Customers and users of our products must themselves observe possible patent rights, existing legislation and
regulations. This publication does not represent a license, nor does it authorize infringement of any type of patent. Note: This version
supersedes and replaces all previous publications on this subject. "Bakelite" is a registered brand of Bakelite AG in more than 50 countries
throughout the world. In the USA, "Bakelite" is a registered brand of the Georgia Pacific Corporation. Bakelite AG is licensed to use the
brand name "Bakelite" for epoxy resins in the USA.

Last update: 2022-07-13 Source: https://www.campusplastics.com Page: 4/4