ADSL 2/2+ ROUTER

User’s Guide
JNet ADSL ROUTER
JN-DS5400

Always ON Connecting…

http://www.jvj.com.sg
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. JNet is a registered trademark of JVJ
Network Group. Other brands and product names are trademarks or registered trademarks
of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without permission
from JVJ Network. Copyright © 2006 All rights reserved.

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CE MARK WARNING
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.

EC DECLARATION OF CONFORMITY (EUROPE)

In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, this
product meets the requirements of the following standards:
• EN55022
• EN55024
• EN60950

SAFETY NOTICES
Caution: Do not use this product near water, for example, in a wet basement or near a
swimming pool.

Avoid using this product during an electrical storm. There may be a remote risk of electric
shock from lightning.

2
Package contents.............................................................................................................4
Chapter 1: Product Overview............................................................................................5
1.1 Product main specification...............................................................................5
1.2 Supporting protocol..........................................................................................5
1.3 Transmit data-rate............................................................................................6
1.4 ATM property...................................................................................................6
1.5 System support................................................................................................6
1.6 Working environment.......................................................................................6
1.7 Electric parameter............................................................................................6
Chapter 2: Hardware Installation Guide........................................................................... 7
2.1 System requirement.........................................................................................7
2.2 LED explanation...............................................................................................7
2.3 Rear-panel.......................................................................................................7
2.4 Hardware installation procedures....................................................................8
Chapter 3: System Configuration......................................................................................9
3.1 Computer Configuration...................................................................................9
3.2 Login..............................................................................................................10
3.3 Web Setup.....................................................................................................12
3.4 Software Dial..................................................................................................21
Chapter 4: Advantage management setup.....................................................................22
Chapter 5: FQA...............................................................................................................23

3
PACKAGE CONTENTS

The following contents should be found in your box:

 One JN-DS5400 External ADSL2+ ROUTER
 One AC power Adapter for JN-DS5400 External ADSL2+ ROUTER
 One Resource CD for JN-DS5400 External ADSL2+ ROUTER, including this Guide
 One RJ45 cable
 One RJ11 cable
 One ADSL splitter

Note: If any of the above items are damaged or missing, please contact the retailer from
whom you purchased the JN-DS5400 External ADSL2+ ROUTER for assistance.

4
CHAPTER 1: PRODUCT OVERVIEW

JNet JN-DS5400 External ADSL2+ ROUTER is the latest product designed and
manufactured by JVJ Network. With JVJ Network’s excellent circuit design and high quality
production, we guarantee the JN-DS5100 ADSL2+ ROUTER’s high performance, great
stability and easy to use.

The JN-DS5400 uses integrated ADSL2+ transceiver and a 256-MHz MIPS32 CPU. The
AFE supports full-rate ADSL connectivity conforming to the ITU and ANSI specifications;
MIPS32 CPU with MMU and 16-KB I-cache/8-KB D-cache is integrated into the device.

In addition to the basic DMT physical layer functions, the ADSL PHY supports dual latency
ADSL framing (fast and interleaved) and the I.432 ATM Physical Layer.

The JN-DS5400 is a complete plug-and-play solution. With standard Ethernet interface, it

can be directly connected to any 10M/100M Ethernet devices, support Auto-MDIX.

1.1 Product main specification

 Adopt the high performance IC which integrate the AFE transceiver and the 256 MHz
MIPS32 CPU, guarantee that this product is efficient and steady.
 High speed and asymmetry data transmit mode, built-in 4-port switch realize multi-
user to share wide-band internet access
 Support All ADSL2+ industrial standards
 Compatible with all mainstream DSLAM (CO)
 Firmware upgradeable
 Provide integrated access of internet and route function which face to SOHO user
 Advanced DMT modulation and demodulation
 Real-time Configuration and device monitoring
 Quick response semi-conductive surge protect circuit, provides reliable ESD and
surge-protect function

1.2 Supporting protocol

 G.992.1 (G.dmt) - Annex A/B/C
 G.992.2 (G.lite) - Annex A/B/C
 ANSI T1.413
 G.992.3 (ADSL2) - Annex A/B/C/M and Annex L (RE-DSL) compliant
 G.992.5 (ADSL2+) Annex A/B/C and Annex L (RE-DSL) compliant
 ADSL dual latency (fast path and interleaved path)
 I.432 ATM physical layer compliant
 Supports RFC2364 (PPPoA)
 Supports RFC2516 (PPPoE)
 Supports RFC1483 (EoA)(Bridged *and Router)
 Supports RFC1577 (IPoA)

NOTE. “*” Needs the third-party software.

5
1.3 Transmit data-rate
 Max download data-rate: 24Mbps
 Max upload data-rate: 1Mbps
 Max line length: 6Km

1.4 ATM property

 AAL0, AAL5, OAM, RM, and raw cell types supported
 Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs
supported in software
 Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)

1.5 System support

 Support PVC

 Support NAT、DHCP and so on

 Support IEEE 802.3、IEEE 802.3u

 Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet
 Support Auto-MDIX

1.6 Working environment

 Operating temperature: 0oC ~ 40oC
 Storage temperature: -40oC ~ 70oC
 Humidity: 10%~90% (non-condensing)

1.7 Electric parameter

 Adaptor power Output: 9VAC/0.8A，50Hz or 60 Hz

 Power consumption: 6W Maximum

6
CHAPTER 2: HARDWARE INSTALLATION GUIDE

The JN-DS5400 maintains five separate interfaces, four Ethernet and one ADSL interface.
The Router should not be located where it will be exposed to moisture or excessive heat.
Place the Router in a location where it can be safely connected to the various devices as
well as to a power source.

2.1 System requirement

Confirm your computer has been installed with networking interface card (NIC) before
connecting ADSL2+ ROUTER to your computer, with operating system supporting the
TCP/IP protocol.

2.2 LED explanation

The front panel of ADSL2+ ROUTER includes one power indicator (RED) and seven
function indicators (GREEN), as explained in the table below:

Indicator Description Status Function details

PWR Power On Power OK

Off Power fail

ADSL ADSL status Slow flash Self-detecting when power up

Quick flash Connecting to the telecom network
On Connection to telecom network OK

ALARM Mistake On There is mistake while sending/receiving

Off ADSL normal

ACT Data On Data is transferring through WAN port

Off No data sending / receiving

LAN 1-4 Ethernet On LAN port is connected

Off Connection fail or no connection
Flash Sending / receiving data

2.3 Rear-panel
 ON/OFF: Turn on/off the ADSL2+ ROUTER’s power.
 Power (9VAC/0.8A input): please do not use any unknown power adaptor, otherwise
your ADSL2+ ROUTER may be damaged.
 RESET (reset default): First press the reset button of ROUTER, then turn on the
ROUTER’s power for at least three seconds. It will resume the default manufacturer’s
setup.
 1~4(LAN): Connect with your computer’s NIC.
 LINE(WAN): Connect to the MODEM Port of Splitter or Connecting the telephone line.

7
2.4 Hardware installation procedures (figure 2.1)

The procedure to install the Router can be described in general terms in the following
steps:

First Step: Connecting the MODEM port of Splitter with the JN-DS5400 ADSL2+
ROUTER LINE port by telephone line. While you need to use a telephone, please attach
telephone line into the phone of Splitter.

Second Step: Connect Cat 5 or Cat 5e cable with RJ45 jacks to the ADSL2+ ROUTER’s
LAN port and your computer’s NIC.

Third Step: Plug one end of the AC Power Adapter into the Power jack on the Ethernet
ADSL2+ ROUTER and the other end to a standard electrical outlet.

Last Step: Check the line connection to see if everything is ready. Power up finally.

8
CHAPTER 3: SYSTEM CONFIGURATION

3.1 Computer Configuration

1. Connect the cable according to Chapter 2, turn on the power.
2. Change the IP address of your PC（Figure 3.1）: Open TCP/IP Properties of the LAN
card in your PC, enter the IP address as 192.168.1.* (* is any value between 2 to 254,
Net mask is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value provided
by ISP). Or you can obtain DNS address automatically by choosing “Obtain DNS
address automatically” option

Figure 3.1

Please note:
Users of Windows 98 can open TCP/IP Properties according to the following: Right-click
(Mouse) Network Neighbor → Choose Properties → Double-click TCP/IP PCI Fast
Ethernet Adapter.

The users of Windows 2000/NT/XP can do the following: Right-click Network Neighbor
→ Choose Properties → Right-click Local Connection → Choose Properties → Double-
click Internet Protocol (TCP/IP).

9
Remarks: you can check whether your configuration is successful through PING
command. Enter Ping 192.168.1.1

If the screen looks like the following, you have been successful.

Pinging 192.168.1.1 with 32 bytes of data:

Reply from 192.168.1.1: bytes=32 time<10ms TTL-128 …

If the screen looks like the following, the connection has failed. Please try again.

Pinging 192.168.1.1 with 32 bytes of data:

Request timed out…

3.2 Login

Startup Internet Explorer, and enter 192.168.1.1; then enter default user name (admin)
password (admin), When ADSL2+ connection is OK, you will see the Figure 3.2

Figure 3.2

Then you will see the Figure 3.3. You will see some information such as link rate and so
on.

10
 Figure 3.3

Default value of user name and password is “admin”; if you want to change them, please
go to “Management” → “Access control” → “Passwords”. (Figure 3.4)

Figure 3.4

11
3.3 Web Setup
Choose “Advanced Setup” → ”WAN”, you will enter the page of Wide Area Network
(WAN) Setup, you will see the Figure 3.5.

Figure 3.5

Choose the fit PVC according to your needs, and then click the Edit button, or choose
Add button to make new PVC link by yourself, you will enter the page of ATM PVC
Configuration (See Figure 3.6)

Figure 3.6
12
Enter VPI/VCI value and service category which is provided by your ISP, click next to enter
the next step. You will see the figure 3.7.

NOTE: The type of network protocol selected may be different in different area, there are
five types（Figure 3.7）, So you should ask your ISP to acquire the local type of network
protocol and Encapsulation mode.

Figure 3.7

After choosing the proper protocol, enter the correct parameters supported by your ISP.
Enable the configurations，then you will go to Internet.

 PPP over ATM (PPPoA)

If you select the protocol of PPP over ATM (PPPoA), you will see the figure 3.8, enter the
value of user name and password which is provided by your ISP, after selecting the other
function(often using the default setup), click the next button.

13
 Figure 3.8

You will see the figure 3.9. Then turn on the selected functions according to your
demands. Clicking the next button to enter the next step, you will see the Figure 3.10.

Figure 3.9

14
 Figure 3.10

Clicking the save button to enter the next step you will see the Figure 3.11

Figure 3.11

Finally click Save/Reboot to complete the configuration. Close the browser Router will
reboot automatically

15
  PPP over Ethernet (PPPoE)

If you select the protocol of PPP over Ethernet (PPPoE), you will see the figure 3.12, enter
the value of user name and password which is provided by your ISP, after selecting the
other function (often using the default setup), click the next button.

Figure 3.12

You will see the figure 3.13 Then turn on the selected functions according to your needs.

16
Clicking the next button to enter the next step, you will see the Figure 3.14, finally click
save to complete the configuration.

Figure 3.14

 MAC Encapsulation Routing (MER)

If you select the protocol of MAC Encapsulation Routing (MER), you will see the page
(Figure 3.15). Enter the parameter and the way which is provided by your ISP, then click
the next button you will see the figure 3.16.

Figure 3.15

17
Then turn on the selected functions according to your needs. Clicking the next button to
enter the next step, you will see the Figure 3.17, finally click save to complete the
configuration.

Figure 3.16

Figure 3.17

18
  IP over ATM (IPoA)

If you select the protocol of IP over ATM (IPoA), you will see the figure 3.18, enter the
parameter and the way which is provided by your ISP, then click the next button you will
see the page (figure 3.19).

Figure 3.18

Turn on the selected functions according to your demands. Clicking the next button to
enter the next step, you will see the Figure 3.20,

Figure 3.19

19
Finally press save to complete the configuration.

Figure 3.20

 Bridging
If you select the Bridging protocol, you just open the bridge service function options, you
will see the figure 3.21, then click the next button, you will see the Figure 3.22, finally press
save to complete the configuration.

Figure 3.21

20
 Figure 3.22

NOTE: After you complete the settings, the new settings must be saved and the Router
must be restarted for the settings to go into effect. Please press the Save/Reboot button to
restart, referring to the Figure 3.11.

NOTE: All of the above setup is under windows XP OS.

3.4 Software Dial

If JN-DS5400 work in bridged (RFC 1483 Bridged) mode when it connects Internet. You
must to install dial software on your PC. There are some software working on WINDOWS
in market, example for EnterNet3000、RASPPPoE、WinPeET.
How do I set up the connection in the windows XP?
 The users of Windows XP can click the “Start → All Programs → Accessories →
Communications → New connection wizard” then click Next to enter the setting
page.
 Please select the “Connect to the internet”, and then click the Next button to enter
the next page and select the “Set up my connection manually”, click Next to enter
the next page.
 Please select the “Connect using a broadband connection that requires user
name and password”, click Next to type the name of your ISP in the current page,
and then click Next.
 Type an ISP account name and password, if you have forgotten an existing account
name or password, please connect with your ISP, click Next.
 To create the connection and close this wizard, click finish to add a shortcut to this
connection to your desktop.
 When you assess the internet by ADSL, double-click this shortcut of dial connection in
your desktop, type the account name and password, then click connect to connect the
Internet.

21
CHAPTER 4: ADVANTAGE MANAGEMENT SETUP

In order to satisfy customer’s needs, feel free to utilize Advantage application and on-line
software upgrade, we provided a perfect Web management interface for you, its main
function is as follows:
 Upgrade software
 Modify the default IP address of the port of LAN(192.168.1.1)
 Modify the login password
 Configure DHCP
 Check the information of IP and the operation status
 Configure the NAT function
 Configure the DNS parameters

 Configure RIP(Routing Information Protocol）

 Configure IP route
 Configure Security rule
 Configure DSL parameter

22
CHAPTER 5: FQA

1. What related parameters are required to acquire ISP when you want to access the
internet by ADSL2+ ROUTER?
1. Dial user: Connection protocol, User name, Password, Value of VCI/VPI,
Encapsulation mode of AAL5 and so on.
2. Static IP user: Connection protocol, WAN IP Address, Subnet Mask, Gateway,
Value of VCI/VPI, Encapsulation mode of AAL5 and so on.

2. About Connection protocol, VCI/VPI, Encapsulation mode of AAL5

1. This product supports the PPP protocol over ATM (PPPoA) 、 PPP over Ethernet
(PPPoE)、MAC Encapsulation Routing (MER)、IP over ATM (IPoA) and Bridging.
That may be used with any one of the five protocols above. Because the ISP in
different areas supports different protocols, choosing protocol must be supported by
ISP.
2. The VPI is the English abbreviation of the Virtual Path Identifier, the VCI is the
English abbreviation of the Virtual Channel Identifier, the value of VCI/VPI must be
compatible with the value that provided by ISP.
3. Encapsulation mode of AAL5 include: LLC/SNAP and VC_MAX(often using
LLC/SNAP).

3. Why are the LAN Indicators and the NIC both bright, but the setting interface is
inaccessible?
1. Use the ping 192.168.1.1 order to check the Accuracy of connection.
2. Check the Accuracy of working NIC.
3. Whatever the setting the IP address of your computer (if you close the DHCP
function, you can't obtain the IP address automatically, must specify the IP address
of your computer manually).
4. Run the winipcfg order in the windows 95/98(run the ipconfig order in the windows
2000) to check the IP address setup, subnet mask, default gateway by DHCP.
5. Resume the ADSL default configuration if necessary.

4. Complete all configurations, but can’t dial through computer

1. Check the indicator led of ADSL, it should be working normally.
2. Check the accuracy of parameter of value of VPI/VCI, Encapsulation mode of AAL5
and so on, whether you need to install the software of dial the number, such as
Winpoet, Enternet.
3. This product has the PPP dial procedure inside, so you will not need to use the dial
software if your protocol is PPPoA or PPPoE, ADSL will connect automatically.
4. You can check whether your router succeeds in connection with PING command.
5. In setting process, the connection is intermitted, how is this done?
6. Please re- log on to the pages, and configure once more.

23