A
A
A
EDITION ANGLAISE
RENAULT CONFIDENTIAL
CLIO 2
Type BB0 J CB0 J SB0 J
Mgane KANGOO
Fitted with the EPIC diesel fuel injection pump
13B
"The repair procedures given by the manufacturer in this document are based on the technical specifications current when it was prepared. The procedures may be modified as a result of changes introduced by the manufacturer in the production of the various component units and accessories from which the vehicles are constructed."
All rights reserved by RENAULT S.A.S. Copying or translating, in part or in full, of this document or use of the service part reference numbering system is forbidden without the prior written authority of RENAULT S.A.S.
13B
1 - Bonnet bolt Remove the mounting bolts (1) from the bonnet. Remove the bonnet. All vehicles Disconnect the battery.
IMPORTANT Please observe the recommendations when disconnecting and reconnecting the battery (see Electrical equipment, Battery: Removal Refitting) (MR 380, 80A, Battery).
Protect areas sensitive to leaking fuel (alternator and air conditioning compressor). Clean the exterior of the rotor sensor and the high pressure pipe unions: Spray brake cleaner, part number: 77 11 226 128 on the edges of the sensor and the high pressure pipe unions, Wipe using lint-free cloths, part number: 77 11 211 707, Blow compressed air over the cleaned parts.
13B -2
13B
Note For the operation to be a success, it is ESSENTIAL to observe the procedure described below.
While keeping the rotor sensor pressed against the pump: undo the mounting bolts, remove the two bolts. Remove the sensor.
IMPORTANT Ensure that the sensor does not touch the core.
2 Pump wiring harness Unclip the rotor sensor wiring harness (3) from its support on the pump side. 4 Rotor sensor Fit the blanking plug on the sensor. Fit the sensor on the engine. 4
13B -3
13B
4 Rotor sensor
Remove the O-ring from the rotor sensor. Using the special socket supplied in the repair kit: undo the core (5) of the rotor sensor. 6 Special socket
IMPORTANT 1 or 2 shims are positioned between the core of the rotor sensor and the rotor. During the removal operation, these shims can be found: - either at the base of the pump, - or on the core. 5
IMPORTANT Ensure that the shims do not fall into the engine or pump. Remove the core of the rotor sensor by hand. 5 Core ADDITION OF THE SPECIAL SHIM Remove the 2 original shims from the core. Fit the special 0.25 mm shim. Refit the original shim(s).
13B -4
13B
torque tighten the mounting bolts to 6 N.m. REFITTING Clip on the electrical sheath of the rotor sensor. After having removed the blanking plugs, refit the high pressure pipes: torque tighten to 25 N.m on the pump side only. Refit the injector return and oil vapour recirculation pipes. Protect the area around the high pressure pipes (from splashes during the bleed operation). Connect the battery.
Note 7 It is ESSENTIAL to carry out the necessary programming (see Battery: Advice) (Technical Note 3682A, 80A, Battery) or (Electrical equipment, Battery: Removal - Refitting) (MR for the vehicle, 80A, Battery).
7 Original shim(s) 8 Special shim Refit the core of the rotor sensor whilst holding the shims.
Bleed the injection system: engage the starter for 5 seconds, prime the circuit using the priming bulb, repeat the operation until air is released from the diesel circuit. Torque tighten the high pressure pipes on the injector side to 25 N.m.
Screw in the core of the rotor sensor completely by hand. Tighten it a quarter of a turn using the tool.
Special notes for Kangoo Refit the bonnet. Tighten the bolts to a torque of 8 N.m.
Clear the fault codes using the diagnostic tool. Lubricate the new O-ring. Remove the blanking plug from the rotor sensor. Fit the O-ring on the sensor body. Refit the rotor sensor, without putting the core under any strain.
Note The fault code must not reappear after having run the flow actuator and advance actuator tests on the pump.
While keeping the rotor sensor pressed against the pump: fit the sensor mounting bolts, tighten the bolts by hand until contact is made, IMPORTANT Do not exceed this value as this may damage the injection pump.
Carry out an operational test. Marking the vehicle after work has been carried out: Add the red CLIP (supplied in the kit) to the wiring harness of the rotor sensor.
13B -5
13B
With PGCS Cause Opecode: Without PGCS NITG code: With or without PGCS Supplier code: Customer complaint code:
Tooling required Conventional. Time required Clio 2 Code 7697 0331 0145 Description Repair of the EPIC pump Vehicle programming Operational test TOTAL Mgane Code 7697 0331 0145 Description Repair of the EPIC pump Vehicle programming Operational test TOTAL Kangoo Code 4191 7697 0331 0145 Description Remove and refit bonnet Repair of the EPIC pump Vehicle programming Operational test TOTAL Time 0.5 0.8 0.2 0.3 1.8 Time 0.8 0.2 0.3 1.3 Time 0.8 0.2 0.3 1.3
13B -6