National Capital Region

DIVISION OF CITY SCHOOLS

QUIRINO HIGH SCHOOL
Molave St., Project 3, Quezon City
SY 2022-2023
Technical Vocational Livelihood
1ST QUARTER TEST
SMAW (Shielded Metal Arc Welding) GRADE 12

I. MULTIPLE CHOICE. Directions. Read and analyze the questions carefully. Choose the
LETTER of the correct answer and write it on the answer sheet.

1. It is the process of joining two metal work pieces together using a flux covered
electrode.
A. Arching B. Chipping
C. Filleting D. Welding
2. This is done by scratching or tapping method.
A. Striking the arc B. Shaping the weld bead
C. Moving the arc to create a bead D. None of the above
3. What process should be done after completing the pass of the metal being welded?
A. Strike the arc
B. Shape the weld bead again.
C. Expose the welded metal in the fan.
D. Chip and brush the weld to remove the slag.
4. Joebert wants to measure the metal that he will be using in the welding activity, what
basic hand tool is appropriate to use?
A. Adjustable pliers B. Chipping hammer
C. Try square D. Wire brush
5. This basic hand tool is used for gripping.
A. Adjustable pliers B. Chipping hammer
C. Try square D. Wire brush
6. In removing the welding slag or spatters, what basic hand tool is needed?
A. Adjustable pliers B. Chipping hammer
C. Try square D. Wire brush
7. In performing an arc welding, which of the following is one of the standard codes of
electrode that is needed?
A. 6013 B. 6014
C. 6015 D. 6016
8. This basic hand tool is used to clean metal welded surfaces.
A. Adjustable pliers B. Blacksmith tongs
C. Chipping hammer D. Wire brush
9. PPE stands for:
A. Personality Protective Equipment B. Personal Protective Equipment
C. Person Protection Equipment D. Personnel Protective Equipment
10. In order to protect your hands from a hot welded metal, what appropriate PPE
should be used?
A. Leather jacket B. Safety shoes
C. Welding gloves D. Welding goggles/helmet
11. Ms. Iscariot is discussing the use of _______ to protect our eyes during
the welding process.
A. Leather jacket B. Plastic goggles
B. Welding gloves D. Welding goggles/helmet
12. It is one of the oldest and most commonly used welding technique.
A. Laser Beam Welding (LBW)
B. Gas Metal Arc Welding (GMAW)
C. Shielded Metal Arc Welding (SMAW)
D. Gas Tungsten Metal Arc Welding (GTAW)
13. One task of a welder is _______ a clean and safe workstation to help eliminate
accidents.
A. cleaning B. ignoring
C. maintaining D. abandoning
14. All of the following are specific career paths for future welders EXCEPT:
A. Accountant
B. Auto body welder
C. Boilermaker
D. Pipe fitter
15. In this job, you will be responsible for repairing and refinishing automotive vehicle
bodies.
A. Auto body welder B. Boilermaker
C. Civil engineer D. Mechanical engineer
16. What will be your task if you are a pipe fitter?
A. Creating boilers.
B. Installing, repairing and maintaining pipes.
C. Repairing and refinishing automotive vehicle.
D. All of the above
17. This is the best tool to manipulate and move the metal work piece.
A. Blacksmith tongs B. Diagonal pliers
C. Long nose pliers D. None of the above
18. In what designated area does a welder do his/ her welding activity?
A. In a field B. In a very narrow area
C. In a trap area D. In a safe location
19. Before you start the welding activity, make sure that your area is _______ .
A. Dry B. Slippery
C. Loaded D. Wet
20. In order to be safe during welding activity, on what example of hazard you should
protect yourself from?
A. Fire B. Rock
C. Knife D. Water
21. Among the welding positions, which is the easiest?
A. Flat B. Overhead
C. Horizontal D. Vertical
22. It is considered as fillet weld if the weld is _______ of the welded metal.
A. at the bottom B. beside
C. center D. in between
23. It is considered as groove weld if the weld is _______ of the welded metal.
A. at the bottom B. beside
C. center D. in between
24. It known as the hardest welding position.
A. Flat B. Overhead
C. Horizontal D. Vertical
25. 1F stands for:
A. Fillet weld in vertical position.
B. Fillet weld in horizontal position.
C. Fillet weld in flat position.
D. Fillet weld in overhead position.
26. It is known as the protective coating of the electrode.
A. Gas coating B. Overhead
C. Horizontal D. Vertical
27.When joining two metal pieces, what correct arc length should be done?
A. 18 mm B. 6 mm
C. 3 mm D. 4 mm
28. This parameter states that in performing arc welding, it should be 1 to 5 second per
movement.
A. Correct electrode angle B. Correct amperage
C. Correct arc length D. Correct travel and speed
29. For a beginner welder, what amperage is suitable to set in a welding machine?
A. 330 A B. 400 A
C. 70 A D. 500 A
30. It is known as the common measurement system.
A. English B. Binary
C. Metric D. Local
31. The following are the fundamental operations used in measuring material EXCEPT:
A. Division B. Addition
C. Multiplication D. Algebraic expression
32. English System is also known as _______ .
A. Metric system B. British (U.S.) system
C. International system D. Local system
33. Inch, yard and pounds are under on what system of measurement?
A. International system B. Metric system
C. English system D. Local system
34. Meters, centimeters, and millimeters are under on what system of measurement?
A. Metric system B. Local system
C. International system D. English system
35.1 inch is equivalent to how many centimeters?
A. 2.54 cm B. 10 cm
C. 5 cm D. 15 cm
36. 15 yard is equivalent to _______ meter.
A. 6 m B. 13.716 m
C. 25.50 m D. 30 m
37. 12 centimeters when converted to feet, is _______ .
A. 0.39 ft. B. 0.5 ft.
C. 0.65 ft. D. 1.6 ft.
38. 6 grams when converted to ounce, is _______.
A. 0.112 oz. B. 0.211 oz.
C. 0.65 oz. D. 1.3 oz.
39. 82 feet when converted to centimeters, is _______.
A. 29 m B. 18 cm
C. 300 cm D. 2499.36 cm
40. 6 quarts is equivalent to _______ liters.
A. 1.15 L B. 1.5 L
C. 5.67 L D. 6.5 L
41. This characteristic involves using of logical, step by step plans to reach the goal you
have set for yourself.
A. Goal oriented B. Persistent
C. Hardworking D. Setting your own standards
42. Aling Chana opens her new business and aims for a good profit. She is a _______
person.
A. Hardworking B. Persistent
C. Profit oriented D. Reliable
43. Despite of many problems, Geebert has a strong faith to his ability in running his
own welding shop someday, what characteristic is he portray?
A. Able to take risk B. Future-oriented
C. Self-confident D. Willing to listen
44. In doing weld passes, what do you call the first pass that is need to be done?
A. Fill pass B. Final capping
C. Hot pass D. Root pass
45. In performing root pass, what suitable electrode is needed to be use?
A. E-6011 B. E-6013
C. E-7018 D. E-7020
46. Roy is done performing hot pass in creating single V butt weld joint. What pass will
be his next move in order to fill the bevel portion?
A. Fill pass B. Final capping
C. Hot pass D. Root pass
47. This refers to a pass that helps smoothen or resurface the already done root pass.
A. Fill pass B. Final capping
C. Hot pass D. Root pass
48. Jojo is done filling the bevel of the welded metals correctly after performing fill pass.
The end process that he needs to be do is ________.
A. Perform tack weld.
B. Perform final capping.
C. Clean the surface of the welded metal.
D. Brush the welded metal and soak it in water.
49. In cutting metals and pipes, what appropriate tool is needed to use?
A. Hacksaw B. Hand drill
C. Pliers D. Vise
50. It is a measuring tape that coils into a compact disc.
A. Hacksaw B. Hand drill
C. Pliers D. Vise

GOODLUCK & GOD BLESS YOU.