Kip3000 SM F4
Kip3000 SM F4
Kip3000 SM F4
KIP 3000
(K-105)
SERVICE MANUAL
(For Europe / Asia Model) Version F.4 June 25, 2007
This service manual includes the basic information about the KIP 3000 Multi-Function Printer, which is required when you during field service to maintain the products quality and reliability.
Chapter 1 Introduction
Overview (Features, specifications, name of parts and etc.) Installation requirements, method of installation, connection with PC & printer explanation for the steps of the print and scan process Circuit diagrams, image process system, electric parts location and etc. Parts replacement and mechanical disassembly Procedure of field service at required intervals Problem resolution Service Mode settings, Diagnosis and etc. General Circuit Diagram
Chapter 2 Installation Chapter 3 Print / Scan Process Chapter 4 Electrical Chapter 5 Mechanical Chapter 6 Maintenance Chapter 7 Troubleshooting Chapter 8 Service Mode and Utility Software Chapter 9 Appendix
Some of the information included in this manual may be changed by product upgrades. Such information will be informed to you through Technical Bulletins or Engineering Change Orders. Read this service manual and these TBs / ECOs to understand the KIP 3000 correctly, and you will be able to maintain the product quality for a long period of time.
Chapter 1 Introduction
1. 1 Features Page 1- 2 111111113 3 4 5 6 6 6 6
1. 2 Specifications 1. 2. 1 General 1. 2. 2 Printer part 1. 2. 3 Scanner part 1. 3 Specifications for Originals 1. 3. 1 Original - Standard 1. 3. 2 Special Documents 1. 3. 3 Do Not Scan Originals 1. 4 Appearance 1. 4. 1 Front 1. 4. 2 Rear 1. 5 Specifications for the Scan Original
1- 7 1- 7 1- 8 1- 10 1- 13 1- 13 1- 14 1- 15
1. 6 Specifications for the Printing Paper 1. 6. 1 Papers not available to use 1. 6. 2 Keeping the paper in the custody 1. 6. 3 Treatment against environmental condition
1-1
K105sm1e1_EUA
1. 1
Features
The KIP 3000 is a single footprint Multi-Function Printer which can copy, scan and print. Advanced drivers and comprehensive print utilities make the KIP 3000 an advanced, easy to use system. (some functions may be optional) The scan and print speeds are up to 60mm/sec or up to 4 landscape D prints/minute. KIP HDP technology generates no waste toner. The combination of the KIP HDP Plus imaging system with mono-component minute toner produces high definition lines, distinctive greyscale and consistent blacks. The maximum paper width is 914mm or 36 wide, and the minimum is 279mm or 11.The maximum paper length is 3.6m or 11.8 (with 36 paper), and the minimum is 210mm or 8.5. Up to 600dpi print and scan resolutions, with an advanced Image Process System, produces the highest quality images. Copier Features Easy Touch screen control panel Collated Sets copying Real-time image preview Recall/reprint previous jobs 600x600DPI copy quality Integrated Accounting and Reports for all copying, network printing, scanning Network ready copier Simple Operator assistance for every day tasks (toner replacement procedure) Image stamping All hardware/software included for instant upgrade from Digital Copier to Network Printer to Scan-to-File system. Information center displays all support information, meter readings, and serial number. Network Printer Features (Optional) Standard TCP/IP connectivity Direct support for vector file formats: HPGL1/2, HP-RTL, Calcomp 906/907 KIP 3000 DWF format support Direct support for raster file formats: TIF Group 3/4, Cals Group 4, Uncompressed Grayscale/Color TIF, Optional KIP 3000 PDF format support: PS/PDF file format. Standard Windows Driver for KIP Script (PS output) and KIP-GL (HPGL/2,RTL output) Standard AutoCAD Drivers Unlimited site license of KIP Request allows users to group supported formats together for printing collated sets. Integrated Accounting in all KIP Drivers/Request for all network printing. Integrated KIP 3000 Web Printing (web server) Open architecture ASCII Job Ticket for third party applications Scan-to-File Features Scan directly to PDF, TIF Group 4, Cals Group 4 Scan to file to FTP or personal inbox on the KIP 3000 Selected resolution up to 600 DPI optical Automatic original size recognition Retrieve scanned image files with KIP Request
1-2
K105sm1e1_EUA
1. 2
1. 2. 1
Specifications
General
Specification KIP 3000 Console 1500W (Including Scanner & IPS) Idling Max. 52db Printing Max. 60db Impulse sound Max. 65db Max. 0.1ppm (Measurement method under UL Standard) 1266mm (W) x 600mm (D) x 1100mm (H) or 50 x 24 x 44 (Operation Panel is not included in these dimensions) 210 kg (1 roll) 217 kg (2 roll) (weights are estimated) Temperature: 10 to 32 Centigrade or 50 to 86 Fahrenheit Humidity: 20 to 85% RH Network Interface (10 BASE-T / 100 BASE-TX) In USA : 120V plus 6% or minus 10%, 50/60Hz, 10A In Europe : 220-240V plus 6% or minus 10%, 50/60Hz, 6A
Subject Model Configuration Maximum power consumption Acoustic noise Ozone Dimensions Weight Environmental condition for usage
NOTE
The above specifications are subject to change without notice.
1-3
K105sm1e1_EUA
1. 2. 2.
Printer part
Specification KIP 3000 Console Single Footprint LED Array Electro-Photography Organic Photoconductive Drum 60mm per second (Metric) 2 A0 / minute (Inch) 2 E or 4 D Landscape / minute LED Array Calibrated 600dpi x 600dpi Maximum 914mm or 36 Minimum 279mm or 11 Maximum Plain paper 3.6m or 11.8 (36) 3 times as long as each standard size (other sizes) Tracing paper Twice as long as each standard size Film Each standard size Minimum 210mm or 8.5
Subject Model Configuration Printing method Photoreceptor Print speed Print head Resolution Print width Print length
NOTE
It is possible to make a longer print than the above shown maximum lengths (24 meters in maximum). But we will not guarantee the image quality or reliability of paper feeding if the page is longer than the above maximum lengths. Warm up time First print time Fusing method Development method Media Less than 4 minutes (23oC or 74F at 60% RH, with the rated voltage, and bond media) 24 seconds (D Landscape) 32 seconds (E) Heat - Pressure Rollers Dry, non-magnetic mono-component toner Plain Paper 64 to 80g/m2 - US Bond (20lbs) Tracing Paper US Vellum (20lbs) Film 4 MIL Recommend media for electro-photography process Store toner from 0 to 35 C (32 to 95 F) and within the humidity range from 10 to 85% RH.
Storage of consumables
NOTE
The above specifications are subject to change without notice.
1-4
K105sm1e1_EUA
1. 2. 3
Scanner part
Specification Contact Image Sensor (CIS) (5 A4) LED 65mm per second Face up Center Max. : 914.4mm or 36 Min. : 275.0mm or 11 Max. : 3.6m (Including the margin area) Min. : 210mm (Including the margin area) 3mm from leading edge and trailing edge 3mm on both left and right 600dpi 600, 400, 300, 200, 100dpi Sheet through type Max. : 0.65mm Min. : 0.05mm
Subject Scanning method Light source Scanning speed Setting of original Starting point of scan Scan width Scan length Margin area Optical resolution Digital resolution Original transportation Transportable original thickness
NOTE
It is possible to scan a longer original than 0.65mm (1.6mm in maximum). But we will not guarantee the image quality or reliability of original feeding if the original is thicker than 0.65mm.
NOTE
The above specifications are subject to change without notice.
1-5
K105sm1e1_EUA
1. 3
1. 3. 1
(1) (2) (3) (4) (5)
The width of original must be from 275.0mm to 965.2mm. The length of original must be 210mm to 25,000mm The thickness of original must be from 0.05mm to 0.65mm. The shape of original must be square, and it must be standard sized. The type of original must belong to any of the followings. Plain paper Coated paper (High or middle class plain paper is coated with the paint.) Tracing paper Pansy Trace Paper (Both sides of the film is sandwiched between Tracing paper.) Film Newspaper Cardboard paper
1. 3. 2
Special Documents
The following kinds of originals are special. It is possible to scan them, but the image quality and feed reliability are not guaranteed. (1) The type of original is acceptable, but the thickness and type may not be: Booklets Original with a Hanger Cut and Pasted originals (2) These original may not damage the scanner, but these types are NOT recommended: following ones. Cloth Aluminium Kent Paper
1. 3. 3
It is impossible to use the following types of originals because they are likely to damage the scanner. (1) (2) (3) (4) (5) (6) Metal originals (The Scan Glass may damage) Slippery originals which is difficult to transport Irregularly shaped originals (Not square in shape) Extremely curled originals (Diameter of curl is less than 50mm) Extremely creased originals Torn originals
1-6
K105sm1e1_EUA
1. 4
1. 4. 1
Appearance
Front
6 7 5 4 3
8 2
9 1
10
11 No. 1 2 3 4 5 6 7 Name Main Switch Original Guides User Interface Emergent Stop Button Original Tray Scanner Unit Toner Hatch (Original Table) Engine Unit Open Lever Bypass Feeder Roll Deck Print Tray Sub User Interface Counter
12
13
8 9 10 11 12 13
Function You can turn on/off the KIP 3000. Feed the original under the Scanner Unit along the Original Guides. This is a Touch Screen, and many kinds of user operation are available. Press this button when you would like to stop copying or scanning emergently. These trays catch the original ejected from the Scanner Unit. Read the original with this unit when you make scan or copy. Open the Toner Hatch when you replace the Toner Cartridge. Also put the original here and then feed it into the Scanner Unit when you make scan or copy. Pull up these levers when you open the Engine Unit. Feed a cut sheet paper from the Bypass Feeder. Roll paper can be set here. (You can set 1 roll paper normally, but 2 roll paper are available if you install the optional 2nd Roll Deck.) Prints are stacked here after the ejection. Service Mode operations are available. It counts the total amount printing. 1-7
K105sm1e1_EUA
1. 4. 2
Rear
7 2
4 5 6
No. 1 2 3 4 5 6 7
Name Exit Cover LAN Port Dehumidify Heater Switch (Option in USA) Breaker Inlet Socket Print Guide Trays COM Port (Optional)
Function Open the Exit Cover when you remove the paper mis-fed inside the Fuser Unit. Connect the LAN Cable to connect the KIP 3000 to the network. Turn on the Dehumidify Heater with this switch when you would like to dry the paper in the humid season. It is possible to shut off supplying the AC power. Connect the Power Cord here. These trays guide the prints to the Print Tray. Connect the cable from the Optional Device. (D-Sub Connector 9 pins: +/-12VDC in maximum)
1-8
K105sm1e1_EUA
1. 5
A scan original must satisfy the following specifications. Thickness Width Length
Do not scan the following kinds of original, because you may damage the original or scanner itself! Sticked with paste Paste
Torn
1-9
K105sm1e1_EUA
Not square
KIP
KIP
Wet
KIP
KIP
Rough surface
Clipped or stapled
Clipped
Stapled
KIP
KIP
1-10
K105sm1e1_EUA
The following kinds of originals can be read with using a carrier sheet. Image quality or the reliability of paper feeding for them is not guaranteed. Patched
Punched
1-11
K105sm1e1_EUA
1. 6
1. 6. 1
Do not use the following kinds of printing paper because you may damage the print engine! Excessively curled (50 mm or less in diameter)
Folded
Creased
Torn
Punched
1-12
K105sm1e1_EUA
Extremely slippery
Extremely sticky Extremely thin and soft Extremely slippery OHP Film
CAUTION
Do not use the paper with staple, or do not use such conductive paper as aluminium foil and carbon paper. Such paper may become cause for the fire.
NOTE
(1) Print image may become light if printed on a paper of rough surface. (2) Print image may become defective if the print paper is much curled. (3) It will become a cause for paper mis-feed, defective print image or crease of paper if you use a paper that does not satisfy the specification. (4) Do not use a paper of which surface is very special, such as thermal paper, art paper, aluminium foil, carbon paper and conductive paper. (5) Tracing paper exposed to air over a long period tends to defective printing. Removing one round on the surface of the tracing roll paper from the beginning is recommended.
1. 6. 2
1. 2. 3. 4.
Keep the paper in the custody taking care of the following matters. Do not expose the paper to the direct sunlight. Keep the paper away from high humidity. (It must be less than 70%) Put the paper on a flat place If you will keep the paper in the custody, which you have already unpacked, put it into the polyethylene bag to avoid the humidity.
1-13
K105sm1e1_EUA
1. 6. 3
Humidity(%)
Low
40% 70%
Void of image occurs when you print with plain paper and tracing paper. Void of image, crease of paper and other problems occurs when you print with plain paper and tracing paper.
High
NOTE
(1) The KIP 3000 is equipped with the Dehumidify Heater (option in USA) Using it in high humidity environment (65% or higher) is recommended. (2) Void of image and crease of paper will occur in case of extremely high or low humidity. Normal Print Crease of paper
Normal Print
Loss of image
1-14
K105sm1e1_EUA
Chapter 2 Installation
The machine had passed our strict inspection after careful adjustment in the factory, and then it was packaged and shipped. Installation is an important work to make the machine work at customers site as same as it has passed our strict inspection before shipment. A service engineer has to understand machines function very well. Install the machine in a good environmental place in a correct way, and then check that it works perfectly.
2. 1
Installation Requirements
Page 2- 2 2- 3 2- 3 2- 6 2- 12 2- 16 2- 18 2- 44 2- 50 2- 52
2. 2 Unpacking 2. 2. 1 Unpacking 2. 2. 2 Confirmation of accessories 2. 3 2. 4 2. 5 2. 6 2. 7 2. 8 Levelling the KIP 3000 Setup of Roll Deck Setup of the Machine Unit Installation of Accessories Turning on the KIP 3000 Initializing the KIP 3000 Scanner
2-1
K105sm2e1_EUA
2. 1
Installation Requirements
1. Power source should be rated as: In Europe / Asia 220-240V+6% or -10%, 50/60Hz, 10A or higher 2. The equipment must be on a dedicated circuit. 3. The outlet must be near the equipment and easily accessible. 1. Make sure to connect this equipment to a properly grounded outlet. 2. The outlet shall be installed near the equipment and shall be easily accessible. Site Environmental Conditions Temperature Range 10 C to 30 C 50 F to 86 F Humidity Range 20% to 85% RH. (NON CONDENSING) Keep the printer away from water sources, boilers, humidifiers or refrigerators. 1. The installation site must not have any open flames, dust or ammonia gases. 2. The equipment must not be exposed to the air vents from heating/cooling systems. 3. The equipment should not be exposed to the direct sunlight. Please draw curtains to block any sunlight. When you open the printer (Upper Half), do not expose the Photoconductive Drum to strong (intense) light as this will damage the Drum. Ozone will be generated while this equipment is in use, although the quantity generated is within all safe levels. (see certifications) Ventilate the room, if so required. Keep ample space around the equipment to ensure comfortable operation. (Refer to the following figure.) The floor must be level and the strength must be ample to sustain the weight of the equipment.
The following conditions are required for the installation of the equipment.
60cm / 24 or larger when the standard tray is installed (Rear) 45cm / 18 or wider 45cm / 18 or wider
KIP 3000
2-2
K105sm2e1_EUA
2. 2
2. 2. 1
Unpacking
Unpacking
2
1. Cut the bands (1), and then remove the top board (2).
2. Remove the outer cardboard box (3). Please note that installation toner and a Software Box will be included in the crate. The Software box has the Software CD and other important installation notes and documents OPEN THIS BOX FIRST DO NOT DISCARD THIS BOX
2-3
K105sm2e1_EUA
4. Open the front face (5) of the bottom board. Remove the wrapped machine (6) with a forklift, and move it to the installation place.
6. Put aside each accessory box (7), Start Up Kit (8) and empty Drum Box (9). DO NOT DISCARD THESE ITEMS. Remove the scanner protection box (10) and the protection papers (11) around the machine. 7 8 10 9
11
2-4
K105sm2e1_EUA
7. Put aside one more accessory box (12) under the Roll Deck. DO NOT DISCARD IT. Remove the padding (13) on Roll Deck Handle. Remove the tapes (14) on both sides.
12
14
13
14
8. Open the Scanner Unit and remove the protection mat (15). Put aside Shading Sheet (16) and Calibration Sheet (17: for machines after S/N 10510001) under the protection mat (15), which will be used on the scanner adjustment. DO NOT DISCARD THE SHEET(S). HANDLE WITH GREAT CARE. KEEP THE SHEET(S) IN SAFE COSTODY FOR AVOIDING DIRT, FOLD OR TEAR.
15
15
16
17
9. Put aside the Power Cord (18) which is on the bottom plate of machine.
18
2-5
K105sm2e1_EUA
2. 2. 2
Confirmation of accessories
Confirm the following parts are attached to the product. Item name Tray Picture Number of article 4
Guide 3
Tray 2 Assembly
2-6
K105sm2e1_EUA
Picture
Number of article 2
1 1
Power Cord
2-7
K105sm2e1_EUA
Picture
Number of article 1
Arm Assembly
Cover 3
Plate 2
2-8
K105sm2e1_EUA
Picture
Number of article 2
Arm 3
Arm 4
Plate 5 Assembly
2-9
K105sm2e1_EUA
Picture
Number of article 1
2-10
K105sm2e1_EUA
Picture
Number of article 4
Setup Procedure
1 1
2-11
K105sm2e1_EUA
2. 3
2 2
2-12
K105sm2e1_EUA
4. Remove 5 screws (4) at the back on both sides. (2 pieces on the right and 3 pieces on the left)
4 4
5. Remove the Side Cover 2 (5) and the Side Cover 3 (6).
2-13
K105sm2e1_EUA
7. Rotate 4 Levelling Bolts (7) on the bottom of the KIP 3000 with a wrench to bring up the KIP 3000 from the floor. Keep 85mm of distance between the bottom plate and the floor. (It is about 80mm before the adjustment.)
85mm
NOTE
Do not rotate the Levelling Bolts too much. If the distance between the bottom plate and the floor becomes wider than 95mm, the Adjuster Bolt may be removed.
2-14
K105sm2e1_EUA
8. Put a level (8) on the specified positions shown to check the level of the KIP 3000. If not levelled, adjust by rotating the Adjustment Bolts. Front Rear
Right
Left
2-15
K105sm2e1_EUA
2. 4
2 Left side
2 Right side
3. Remove the tape (3) at the center, which fixes the Guide Plate.
2-16
K105sm2e1_EUA
2-17
K105sm2e1_EUA
2. 5
2-18
K105sm2e2_EUA
4. Remove the screws (4) and flat washers (5) to release the Bands (6) at both sides.
5. Rotate up the Pins (7) and move them to the inside to pull them out from the holes. Remove the Toner Cover 4 (3).
2-19
K105sm2e2_EUA
10
2-20
K105sm2e2_EUA
10. Remove 2 pieces of red screw (12) at both sides of the Developer Unit, which protect the Developer Unit from vibration during transportation. (They are no longer required.)
12
12
11. Holding both sides plates firmly, slide the Developer Unit (13) out of the machine. 13
12. On the right (electrode plate side) of the unit, remove the red screw with tag (14). (This red screw will not to be reused.)
14
2-21
K105sm2e2_EUA
15
14. Completely press down and hold the Bracket 5 (16), and tighten the screws (15). (The Regulation Roller is pressed onto the Developer Roller.) 16
15
15
2-22
K105sm2e2_EUA
NOTE
(1) The Regulation Roller (17) is not pressurized during the transportation not to damage the Developer Roller (18), but it must be pressurized by pressing down the Bracket 5 (16) before using the machine. If you do not do it, too dark image will be printed out. 17
18
(2) Make sure to fix the right side (electrode plate side) of the Regulation Roller first then the left side (gear side). The pressure of Regulation Roller will be unbalanced between left and right if you do not follow this order.
15. On the left (gear side), loosen 2 screws (19) which fixes the Bracket 4. And also loosen the screw (20) which fixes the Bracket 6.
19
20
19
2-23
K105sm2e2_EUA
16. Completely press down and hold Bracket 4 (21), tighten the screws (19) to fix Bracket 4 (21).
19
21
19
NOTE
(1) The Regulation Roller (17) is not pressurized during the transportation not to damage the Developer Roller (18), but it must be pressurized by pressing down the Bracket 4 (21) before using the machine. If you do not do it, too dark image will be printed out. 17
18
(2) Make sure to fix the right side (electrode plate side) of the Regulation Roller first then the left side (gear side). The pressure of Regulation Roller will be unbalanced between left and right if you do not follow this order.
2-24
K105sm2e2_EUA
17. Tighten the screw (20) to fix the Bracket 6 (22). (It is unnecessary to press down the Bracket 6 at this point of time.) 22
20
NOTE
Note that Bracket 6 (22) on the left is fixed with the screw (20) although the Bracket 7 (23) on the right is not fixed. The Regulation Roller can press the Developer Roller with an even pressure with this state. 22
23 20
Fixed
Not fixed
18. Remove the Gear Package (24) on the Hopper and carefully unpack it. You will find a Collar (25), a Parallel Pin (26), a Gear Helical (27) and a Retaining Ring-E (28). 24 28 26
27
25
2-25
K105sm2e2_EUA
19. Set the Collar (25) onto the shaft of Regulation Roller. Install the Parallel Pin (26) to the shaft. 25
26
NOTE
Be careful of the direction of the Collar (25). Install it as shown. 25
2-26
K105sm2e2_EUA
20. Install the Gear Helical 20T (27) to the shaft, and fix it with the Retaining Ring-E (28).
28
27
NOTE
(1) Press the Gear Helical 20T (27) to the arrow direction. (you may rotate the Developer Roller Shaft with the Developer Handle (29) to easily install the Gear Helical 20T.) 27
29
(2) Do not rotate the Developer Roller when the Gear Helical 20T (27) is not installed to the shaft of Regulation Roller! The Seal 3 or the Seal 4 (30) inside of the Developer Unit will be broken if you do so. 30 30
2-27
K105sm2e2_EUA
32
32
33
34
34
2-28
K105sm2e3_EUA
36 36
26. Shake the Starting Toner Bottle (37) well, and add the toner to the Developer Unit. (Please even out the toner in the development unit.)
37
2-29
K105sm2e3_EUA
27. Insert the Developer Handle (29) to the shaft of Roller Developer, and rotate the Roller Developer several times so that its surface is covered with the toner. Developer Handle Part Number : Z050320050 29 29
NOTE
Readjustment of the pressure of Regulation Roller
If the pressure of Regulation Roller is weak, the toner layer on the Developer Unit will be much thicker than required when you rotate the Developer Roller in the above procedure 27. Pressurize the Regulation Roller in the correct way as shown below in this case. (You will not be able to pressurize it successfully by the usual way of pressurization.) (1) On the right side (Electrode Plate side) of the unit, press and hold the Bracket 5 (16) to the arrow direction completely, and fix it with the screws (15). 16
15 15
(2) On the left side of the unit (gear side), confirm that the Bracket 4 (21) is fixed with the screws (19) being completely pressed to the arrow direction. Also confirm that the screw (20) is loosened and the Gear Helical 20T (27) is installed. 21 19 19 20
27
2-30
K105sm2e3_EUA
NOTE
Readjustment of the pressure of Regulation Roller
(3) Fully press down and hold the top of the Bracket 6 (22). With holding, rotate the Developer Roller twice with the Developer Handle (29). Check that the toner layer on the Developer Roller gets thinner. 22
22
29
(4) Remove both the Retaining Ring-E (28) and the Gear Helical 20T (27).
28
27 & 28
27
22
20
2-31
K105sm2e3_EUA
NOTE
Readjustment of the pressure of Regulation Roller
(6) Reinstall the Gear Helical 20T (27) and the Retaining Ring-E (28).
28
27
27 & 28
36
NOTE
Be careful of the direction of Separator (36). Do not install it in the wrong direction. 36
2-32
K105sm2e3_EUA
35
32
NOTE
Do not install the Developer Unit at this time, as it must be removed when you setup the Drum in the later procedure.
30. The process unit and toner cover should be open. The Photoconductive Drum is covered with a black sheet (38). Gently pull and remove it.
38
38
2-33
K105sm2e3_EUA
13
NOTE
Both the Gear Helical 34T (39) on machine side and the Gear Helical 28T (40) on Developer Unit side must be in gear firmly with each other, but they may not be in gear with each other by just installing the Developer Unit to the machine.
39
40 After installing the Developer Unit to the machine, rotate the Gear Helical 34T (39) by hand from under the Engine Unit. Both gears will be in gear by this way.
39
32. Close and fix the Developer Press Unit (10), and put back the Cover 4 (3).
10 2-34
3
K105sm2e4_EUA
34. Both the LED Head and the Image Corona are locked with the screws (41) being separated from the Drum, not to be damaged during the transportation. Loosen the screws (41) to unlock the Fixing Brackets (42) at both sides. Pressing down the Fixing Brackets (42) firmly, tighten the screws (41).
42
42
41
41
NOTE
Please satisfy the following requirements before performing Step 34. (1) The black sheet has been removed from the Drum. (See the former procedure 30.) (2) The Engine Unit is closed firmly. (See the former procedure 33.) Otherwise a proper distance can not be kept between LED Head and Drum.
2-35
K105sm2e4_EUA
35. Fit the Arm Assembly (43) to the bracket of Monitor Assembly (44), with 4 - 4 x 6 screw (45). 43
44
45 45
2-36
K105sm2e4_EUA
36. Connect the VGA Cable (46), Power Supply Cable (47) and USB Cable (48) to the Monitor.
46
47
48
NOTE
Make sure that both Power Supply Cable and USB Cable are under the Core (49) of the VGA Cable to avoid any electrostatic issues. 49
37. Install the Cover 3 (50) to the Arm Assembly with 4 pieces of 3x6 screw (51).
51 51 50
2-37
K105sm2e4_EUA
38. Remove 4 screws (52), loosen 4 screws (53), and remove the Cover 15 (54). 52
54
53
39. Disconnect the connector (55), remove 5 screws (56), and remove the Case 5 (57). 56
57
55
56
40. Put a 4x8 tooth washer screw (58) to the screw hole as the photo. (Do not tighten it.) Also remove the Bushing (59) from the Right Side Plate.
58
59
2-38
K105sm2e4_EUA
41. Hold the harness with the Bushing (59), and fit it to the Side Plate.
59
59
2-39
K105sm2e4_EUA
42. Fit the screw hole (60) of the Arm Assembly to the tooth washer screw (58) you have put in step 40. 58 60
58
43. Fix the Arm with 4 - 4x8 tooth washer screw (58).
58
58
2-40
K105sm2e4_EUA
44. Insert the harnesses (61) into the machine through the hole (62). Bundle the harnesses with the Wire Saddles (63).
62 63 61
NOTE
(1) As the USB Cable (48) is a little long, curve it outside of the Side Plate, and bundle it with the Wire Saddle (63). (It is not recommended to curve it inside of the Side Plate, because there are many cables inside of the Side Plate so it will become very complicating if you do so.) 48 63
(2) There are 2 kinds of cable inside of the machine. One is the internal cable such as USB Cable, VGA Cable and Power Supply Cable. And another is the external one such as LAN Cable and Folder Cable (Option). These 2 kinds of cable must not be bundled with the same Wire Saddle because a noise problem may occur. Therefore bundle the internal cables only with the Wire Saddles at this time. (The blue cable is the LAN Cable, so do not bundle it.) LAN Cable
45. Connect the Power Supply Cable (47) to the connector (64) of the DC Power Supply. Hold the Power Supply Cable (47) with the Wire Saddles (65) at this time. 47 64
65 2-41
K105sm2e4_EUA
46. Connect the VGA Cable (46) and USB Cable (48) to the concerning terminal of Controller PC. Hold these cables with the Wire Saddles (66).
46 66
48
NOTE
There are 2 kinds of cable inside of the machine. One is the internal cable such as USB Cable, VGA Cable and Power Supply Cable. And another is the external one such as LAN Cable and Folder Cable (Option). These 2 kinds of cable must not be bundled with the same Wire Saddle because a noise problem may occur if these cables are mixed. Take care of the following matters. (1) There are 2 Wire Saddles on each PC Cover. Bundle the internal cables with the front one (66) of them. Note that the rear one (67) is for the external cable. 66
67
(2) Between the Wire Saddle (66) and the terminal of each cable, bundle each VGA Cable, Power Supply Cable and external cable together with the same Wire Saddle (68). But do not bundle the USB Cables (69 : for both scanner and UI) together at this time, because the USB Cable is the great cause for a noise issue. 66 69 68
2-42
K105sm2e4_EUA
57
48. Replace the Cover 15 (54), Cover 3 (70) and Cover 2 (71). 55
71
70
2-43
K105sm2e4_EUA
2. 6
Installation of Accessories
2 1
1. Fit 2 pieces of Guide 3 (1) to the notches (2) on the Cover 10.
2-44
K105sm2e5_EUA
3. Loosen 4 screws (4), fit the Plate 2 (5) to the screws (4), and tighten the screws (4). 4
2-45
K105sm2e5_EUA
NOTE
(1) Insert all Arm 3 (7) and Arm 4 (8) as the following photos. (Be careful of the direction of insertion.)
(2) Direct the flat end of each Arm 3 (7) and Arm 4 (8) to the bottom. Prints will not be stuck satisfactory when they installed upside down. Flat end
2-46
K105sm2e5_EUA
7. Attach 2 Plate 5 Assembly (10) with 4x6 Bind Screws (9) you have removed at step 6. 10
boss
10
10
NOTE
Fit the positioning bosses on Plate 5 Assembly to the positioning holes on machine side at this time.
2-47
K105sm2e5_EUA
8. Fit 4 pieces of Tray (11) to the notches on the rear of the machine. 11
notch
13
13
NOTE
Insert the tip plate (14) of the Guide 4 (12) into the slit (15) of the Tray 2 Assembly (13).
14
15
2-48
K105sm2e5_EUA
10. Put Tray 2 Assemblies (13) onto the slide rails (16) on the bottom. Fix them with 2 screws (M3x8) (17). 17 17 16
17 13
NOTE
Change the position of Tray 2 Assemblies (13) according to the format of printing paper. ISO (A/B) Pull out completely Architecture Align with the marking line. Engineering Push in completely
2-49
K105sm2e5_EUA
2. 7
WARNING
(1) Do not handle the Power Plug with wet hands, or you may receive an electrical shock. (2) Make sure to ground the machine for safety. (3) Do not plug the printer into a multi-wiring connector in which other devices are plugged. It may overheat the outlet and may result in a fire. (4) The outlet must satisfy the following conditions. In Europe : 220-240V plus 6% or minus 10%, 50/60Hz and 10A
2. There is a Power Switch on the right side of KIP 3000. Press it to the I side to turn on the KIP 3000.
Power Switch
2-50
K105sm2e5_EUA
3. The User Interface (UI) starts operating, and it indicates the following Copy Mode Screen in about 1 minute. There is a Ready Indicator on the Copy Mode Screen, which flashes during warming up. Ready Indicator
4. The Ready Indicator lights green when the KIP 3000 is ready. Set media type / width and then make a test copy.
2-51
K105sm2e5_EUA
2. 8
After the setup, the KIP 3000 scanner requires initialization. This provides a clearer and more accurate scan image. Follow the below outline to initialize the KIP 3000 scanner with Scanner Utility. 1. Install USB driver and Scanner Utility. See [8.12.1 Installation] on page 8-185. 2. Perform Shading and Calibration (if supported). See [8.12.4 Scanner Adjustment] on page 8-194.
2-52
K105sm2e5_EUA
3. 1 Print Process 3. 1. 1 Characteristic of toner 3. 1. 2 Each step of the print process 3. 2. 1 Erasing (Removal of negative electric charges) 3. 2. 2 Charge of Drum 3. 2. 3 Exposure 3. 2. 4 Development 3. 2. 5 Transfer 3. 2. 6 Separation 3. 2. 7 Drum Cleaning (Removal of remained toner) 3. 2. 8 Fusing 3. 1. 3 Controlling the movement of toner in the Developer Unit 3. 1. 4 Toner Collection Process 3. 2 Scan Process 3. 2. 1 Data flow in scan and copy 3. 2. 2 Positioning process of Image Block 3-1
Page 3- 2 3- 2 3- 3 3- 5 3- 6 3- 7 3- 8 3-10 3-11 3-12 3-13 3-14 3-17 3-20 3-20 3-21
K105sm3e1_EUA
3. 1
3. 1. 1
Print Process
Characteristic of toner
The toner for the KIP3000 has a characteristic to be charged negative, which tends to be attracted to a more positive object. Suppose that there are objects A and B, and the situation is as follows. 1. Electric potential of the object B is higher than that of object A. 2. Toner exists on the object A. Comparing the potential of both objects, it can be said that the object B is relatively positive and the object A is negative. (In another word, object B is more positive than the object A.) As the toner is negative, it is attracted to the object B that is more positive. If you move the object B close to the object A, therefore, the toner moves onto the object B.
A
Toner moves from A to B.
On the contrary, suppose that the toner exists on the object B of which electric potential is higher than the object A. Even if you move the object A close to the object B, the toner continues to stay on the object B because negative toner and relatively negative object A repel each other.
Toner stays on B.
Thus, the toner has a characteristic to move from one place with a lower potential to another place with a higher potential. If we control the electric potentials, it is possible to move the toner from one place to another as we intend, or it is also possible to remove the toner from an unwanted place. The KIP3000 controls the electric potentials properly working each part as Drum, Corona Units, Lamps, Developer Unit and Cleaning Roller. The movement of toner is controlled correctly and several processes as Development, Toner Transfer, Drum Cleaning and etc. are performed.
3-2
K105sm3e1_EUA
3. 1. 2
1. 2. 3. 4. 5. 6. 7. 8.
One cycle of print consists of the following 8 processes. Erasing (Removal of negative electric charges) Charge of Drum Exposure Development Transfer Separation Drum Cleaning (Removal of remained toner) Fusing
Image Corona
Eraser Lamp
Fuser Roller
Cleaning Roller
3-3
K105sm3e1_EUA
Processes from 1 to 8 are related with the control of the electric potentials. The following graphic shows the electric potential at each process and the movement of toner.
+700V +600V +500V +400V +300V +200V +100V 0V - 100V - 200V - 300V - 400V - 500V - 600V - 700V 2 SP2 1 6 3 1 SP1 4 5 7
Surface Potential of Drum SP1 : For black image / SP2 : For white image
Name of part Image Corona Wire Grid Plate Developer Roller Regulation Roller (Center) Regulation Roller (Both sides) Toner Supply Roller Transfer Corona Separation Corona Cleaning Roller Voltage (Current) during Print Cycle -1.3mA +/-0.02mA -620V +/-30V -230V +/-5V -40V +/-5V against the Developer Roller Bias 0V (Connected to the ground) Same voltage with the Developer Roller Bias +500V +/-30V AC (5.0KV) + DC (-250V +/-5V) +450V +/-5V +350V +/-5V -40V +/-5V against the Developer Roller Bias 0V (Connected to the ground) Same voltage with the Developer Roller Bias -550V +/-5V Voltage during Toner Collection Process
Reference
When the printer is going to stop after printing, or when the used Roll Deck is changed with other one, the KIP3000 Digital Printer will take the Toner Collection Process to remove the remained toner and place back into the Developer Unit. Refer to [3.1.4 Toner Collection Process] on the page 3-17 for the detail.
3-4
K105sm3e1_EUA
3. 1. 2. 1
As the first step of print cycle, it is necessary to remove the negative electric charges from the Drum, which have remained there after the former print cycle. The Drum has a characteristic to lose the negative electric charges if it is exposed to the light. So the Drum is rotated and evenly exposed to the light from the Eraser Lamp. The electric potential on the Drum becomes 0V (residual potential) by this process.
0V 0V 0V
Eraser Lamp
Drum
3-5
K105sm3e1_EUA
3. 1. 2 .2
Charge of Drum
The Image Corona discharges negative electric charges which are given to the Drum. The surface of Drum becomes about -620V evenly as a result, which corresponds to the white area of the printed image pattern. The Grid Plate is also connected to the High Voltage Power Supply individually. Current and Voltage supplied to the Image Corona Wire is as follows. Corona Wire -1.3mA +/-0.02mA
Corona Wire
Image Corona
Grid Plate
620V 620V 0V 0V
Drum
3-6
K105sm3e1_EUA
3. 1. 2. 3
Exposure
According to the printed image pattern, the LED Head throws the light (740nm) onto some part of Drum which corresponds to the black area of printed image pattern. As the Drum has a characteristic to lose the negative electric charges if it is exposed to the light, this part of Drum surface loses the charges and its potential becomes about -20V. (This potential is not constant but is variable by the environment.) The other part of Drum surface, which was not exposed to the light from the LED Head, keeps -620V of potential which the Image Corona has given. An invisible electric image pattern that consists of -620V area and the -20V area is formed on the surface of Drum as a result. (This is called Electrostatic Latent Image.)
LED Head
20V 20V
620V
620V 0V 0V
Drum
-20V
-620V
Reference
Even if the toner remains on the Drum, it will not block the light from the LED Head as the diameter of toner (9 micrometers) is much smaller than that (42 micrometers) of 1 pixel of LED. The electric charges on the Drum are removed as needed.
3-7
K105sm3e1_EUA
3. 1. 2. 4
Development
The Developer Roller, which is evenly covered with the toner, is contacted to the Drum because the Developer Unit is pressed to the Drum. (The width of contact point is about 5mm.) The Developer Roller is supplied with -230V (+/-5V) during the print cycle. And both -620V area and -20V area exist on the Drum because the Electrostatic Latent Image has been formed in the former Exposure process. Seen from the voltage of Developer Roller Bias (-230V), the -20V area on the Drum is relatively positive. So the toner moves from the Developer Roller to the -20V area of Drum. On the other hand, the -620V area is relatively negative seen from the Developer Roller. So the toner does not move to the -620V area but stays on the Developer Roller. A visible toner image is formed on the Drum as a result. Developer Roller Drum Developer Roller Drum
Before Development
-20V
3-8
K105sm3e1_EUA
Even if some toner has not been removed by the Cleaning Roller but remained on the -620V area of Drum (It corresponds to the white area of the print) in the later [3.1.2.7 Drum Cleaning], this toner is removed at the time of Development because it moves to the Developer Roller of which potential (-230V) is higher than that of Drum (-620V). So there will be no case that unnecessary black spot is printed on the white area of the print. The remained toner that moved to the Developer Roller is carried into the Developer Unit and then reused. 1. 2. 3. 4. 5. Toner remained on the Drum Toner moves from the Drum to the Developer Roller. Developer Roller carries the toner toward the Toner Supply Roller Toner is shifted to the inside of the Developer Unit by the revolution of Toner Supply Roller. Toner is reused.
3 4
-20V
-620V
Reference
The Developer Unit has not only the Developer Roller but also 2 more rollers inside which are also supplied with the individual voltages. The Developer Unit controls the movement of toner in the unit taking advantage of the difference of potentials among these rollers, and covers the Developer Roller with the toner in the end. Refer to [3.1.3 Controlling the Movement of Toner in the Developer Unit] to know how the Developer Unit controls the movement.
3-9
K105sm3e1_EUA
3. 1. 2. 5
Transfer
The printing paper is charged positively as the Transfer Corona discharges positive electric charges from under the paper. The toner existing on the -20V area on the Drum will move to the printing paper because the potential of the paper comes to be higher than the Drum by the Transfer Process. The voltage supplied to the Transfer Corona Wire is as follows. Transfer Corona Wire : +500 +/-30V (When the Insulated Drum is used.) Printing paper
20V 20V
20V
Transfer Corona
3-10
K105sm3e1_EUA
3. 1. 2. 6
Separation
The printing paper is attracted to the Drum after the Transfer because the potential of paper is positive and that of Drum is negative. It is necessary for avoiding the jam to separate the paper from the Drum by removing the static force between them. The Separation Corona takes AC discharge being supplied with the AC voltage and the DC voltage. AC voltage : 5.0KV DC voltage : -250V As the AC voltage is compensated by the negative DC voltage, the negative charges are generated more than positive ones, which mainly results in removing the positive charges of the printing paper. On the other hand, the Separation Lamp throws light from under the Corona Wires to remove the negative charges of the Drum. The static force between the printing paper and the Drum is reduced as a result, and the paper is separated from the Drum by its weight. Negative charges of the Drum are removed by the light from the Separation Lamp.
Drum
620V 20V
3-11
K105sm3e1_EUA
3. 1. 2. 7
Some amount of toner that has not been transferred onto the printing paper is remaining on the Drum. This remained toner will be removed by the Cleaning Roller. The Cleaning Roller is supplied with +450V (+/-5V), and there are some negative electric charges on the Drum at this time. As the Cleaning Roller is relatively positive and the Drum is negative, the toner moves from the Drum to the Cleaning Roller.
Cleaning Roller
450V
NOTE
If too much toner exists in a small area (like a trace of solid black image) the Cleaning Roller may not be able to remove all of them. But this toner is removed from the Drum in the Development Process. Refer to the page 3-9 for the detail.
3-12
K105sm3e1_EUA
3. 1. 2. 8
Fusing
After Transfer / Separation Processes, the printing paper is transported to the Fuser Unit by the Inner Transport Unit. The Fuser Unit mainly consists of the Fuser Roller and the Pressure Roller. The Fuser Roller is very hot, and the Pressure Roller is strongly pressed to the Fuser Roller by the spring. The toner is firmly fused onto the printing paper by the heat and the pressure when the paper passes through between these rollers. Fuser Roller
Pressure Roller
3-13
K105sm3e1_EUA
3. 1. 3
There are 3 kinds of rollers called Developer Roller, Regulation Roller and Toner Supply Roller in the Developer Unit. Each roller is supplied with its own voltage. In the following list, the voltage of the Developer Roller (-230V) is measured against the ground. The other voltages mean the difference against the voltage of Developer Roller Bias. Name of roller Developer Roller Regulation Roller (Center) Regulation Roller (Both sides) Toner Supply Roller Supplied voltage -230V +/-5V against the ground -40V +/-5V against the Developer Roller Bias 0V (Connected to the ground) Same voltage with the Developer Roller Bias (Developer Roller and Toner Supply Roller are short circuited being connected with the plate.)
Insulator
Toner Supply Roller (Same voltage with the Developer Roller Bias)
NOTE
The Regulation Roller is divided into central area and both side areas by the insulator, and individual voltage is supplied to each area.
3-14
K105sm3e1_EUA
Taking advantage of the difference of potentials among these rollers, the movement of toner is controlled in the Developer Unit as follows. 1. The Toner Supply Roller carries the toner toward the Developer Roller. 2. The toner sticks onto the surface of the Developer Roller by the friction, and then it is carried by the Developer Roller to Regulation Roller side. 3. The Regulation Roller is strongly pressed to the Developer Roller by the spring, and these 2 rollers move to the opposite direction each other at the contact point. Even if the Developer Roller carries more toner than required, the Regulation Roller limits the amount of toner that can pass through between 2 rollers. So very small amount of toner can pass through between rollers and the rest is returned back to the inside. As the voltage of Developer Roller is 40V higher than that of Regulation Roller (Center), the toner which has passed through between rollers is firmly attracted to the Developer Roller. Very thin layer of toner is evenly formed on the surface of Developer Roller as a result. 4. Much toner sticks onto the Regulation Roller when it is returned back to the inside. This toner is scraped off by the Scraper which is contacted to the Regulation Roller.
Scraper
4 3
3-15
K105sm3e1_EUA
5. The voltage of both sides of Regulation Roller is 0V as these parts are connected to the ground. It is higher than that of Developer Roller (-230V). When the toner reaches the contact point of these rollers, therefore, it moves onto the Regulation Roller. The side areas of the Developer Roller are not covered with the toner as a result, so it is possible to avoid the toner drops into the machine from the side. Regulation Roller : Both Sides (0V : Connected to GND)
Regulation Roller : Center (-40V against Developer Roller voltage) Toner area
Non-toner area
3-16
K105sm3e1_EUA
3. 1. 4
As explained in [3.1.2.7 Drum Cleaning] on the page 3-12, the Cleaning Roller is supplied with +450V to remove the remained toner from the Drum during the print cycle. This toner gathered by the Cleaning Roller is returned to the Developer Unit in the following 3 cases. (1) When the printer has finished printing out all the accumulated print jobs and then going to stop. (2) When the used roll paper is ended and changed with another one. (3) When the used roll paper is changed from one to another because the print size specified in the job is different. This process to return the toner is called Toner Collection Process. When the trailing edge of the last sheet passes over the Separation Area, the printer will take the Toner Collection Process as follows rotating the Drum for 2 revolutions. 1. The Eraser Lamp throws light onto the Drum to remove the negative electric charges from the Drum. The potential of Drum becomes 0V. 2. The voltage supplied to the Cleaning Roller is changed to -550V in the Toner Collection Process. As the potential of Drum becomes higher than that of Cleaning Roller, toner on the Cleaning Roller moves onto the Drum.
0V 0V 550V 0V
Remained toner
Drum
Cleaning Roller
3-17
K105sm3e1_EUA
3. The voltage supplied to the Developer Roller is also changed to +350V (+/-5V) in the Toner Collection Process. As the potential of Developer Roller becomes higher than that of Drum, toner on the Drum moves onto the Developer Roller. Then the toner is carried into the Developer Unit by both the Developer Roller and the Toner Supply Roller. Remained Toner
0V 0V
Drum
350V
0V
Developer Roller
3-18
K105sm3e1_EUA
Reference
Voltages supplied to Regulation Roller and Toner Supply Roller are changed also as follows. Name of roller Developer Roller Regulation Roller (Center) Regulation Roller (Both sides) Toner Supply Roller Supplied voltage +350V +/-5V against the ground -40V +/-5V against the Developer Roller Bias 0V (Ground) Same voltage with the Developer Roller Bias
Toner Supply Roller (Same voltage with the Developer Roller Bias)
3-19
K105sm3e1_EUA
3. 2
3. 2. 1
Scan Process
Data flow in scan and copy
There are CIS Units, CIS Controller PCB and Data Controller PCB in the scanner unit, which take image reading and processes the data. 1. The CIS Units read the image pattern of original and then send the analog data to the CIS Controller Board. 2. The CIS Controller Boards converts the analog data into digital data and then send to the Data Controller PCB. 3. The Data Controller PCB takes the correct image process according to the UI setting. Then it outputs the image data to the IPS through the USB 2.0. 4. The IPS output the image data to the printer part of the KIP3000 through the Interface 8 in case of copy, or it outputs to the Network PC through the LAN cable in case of scan to file.
CIS
CIS
CIS
CIS
Digital data
USB 2.0
IPS (Controller)
LAN Network PC
3-20
K105sm3e1_EUA
3. 2. 2
The scanner part of the KIP3000 reads the image of original with 5 - CIS (Contact Image Sensor). As these CIS are arranged in 2 rows, there occurs a vertical gap of image among the image blocks. So it is necessary to remove this gap by vertical positioning process (Y offset). Also the reading area of these 5 pieces of CIS overlaps each other some degree. It means some image pixels are commonly included in the neighbouring two Image Blocks. It is very hard to recognize the image because many images are duplicated. To prevent this kind of problem, it is necessary to remove the duplication of image pixels by horizontal positioning process (X overlap). The Data Controller PCB performs these positioning processes.
NOTE
The KIP3000 performs these positioning processes (X overlap & Y offset) according to the setting specified through Scanner Utility. Please refer to [8.12. 4. 4 Position] as for this setting.
[Explanation] 5 pieces of CIS are arranged in 2 rows as the following illustration, with some amount of their reading area overlapping each other. So the reading data initially inputted to the Data Controller PCB is as follows. (1) There occurs a vertical gap of image among the image blocks. (2) Some image pixels are commonly included (duplicating) in the neighbouring two Image Blocks. Reading areas
CIS
The Data Controller PCB removes the vertical gap among the Image Block according to the positioning setting (Y offset) specified through Scanner Utility. The image data before the positioning process
3-22
K105sm3e1_EUA
Also the Data Controller PCB removes the duplication of image pixels among the Image Blocks according to the positioning setting (X overlap) specified through Scanner Utility. The image data after the positioning process (Y offset)
3-23
K105sm3e1_EUA
Chapter 4 Electrical
4. 1
General Information
Page 4- 2 4- 3 4- 3 4- 7 4- 8 4-12 4-13 4-15 4-18 4-19 4-21 4-24 4-25 4-26 4-30 4-30 4-31 4-33 4-35 4-37 4-39 4-41 4-43 4-45 4-47
4. 2 Electrical Components Location 4. 2. 1 Right side 4. 2. 2 Left side 4. 2. 3 Back side 4. 2. 4 Front side 4. 2. 5 LED Head Frame 4. 2. 6 Main Frame 4. 2. 7 Developer Unit 4. 2. 8 Fuser Unit 4. 2. 9 Roll Deck 4. 2.10 Cutter Unit 4. 2.11 Inner Transport Unit 4. 2.12 Scanner Unit 4. 3 Check & Adjustment of Analog Output from HV Power Supply 4. 3. 1 Situations necessary to check the analog output 4. 3. 2 Check & Adjustment of Analog Voltage to the Image Corona 4. 3. 3 Check & Adjustment of Analog Voltage to the Transfer Corona 4. 3. 4 Check & Adjustment of AC Component to the Separation Corona 4. 3. 5 Check & Adjustment of DC Component to the Separation Corona 4. 3. 6 Check & Adjustment of Negative Developer Bias to the Developer Roller 4. 3. 7 Check & Adjustment of Positive Developer Bias to the Developer Roller 4. 3. 8 Check & Adjustment of the Bias gap between Developer Roller and Regulation Roller 4. 3. 9 Check & Adjustment of Positive Cleaning Roller Bias (Print Cycle) 4. 3.10 Check & Adjustment of Negative Cleaning Roller Bias (Toner Collection Process)
4-1
K105sm4e1
4. 1
General Information
This machine is mainly controlled by a microcomputer, which is located on DC Controller. This microcomputer reads input signals from sensors, and outputs the operation signals to motors, SSRs, solenoid, clutches and blowers on programmed timing. Sensor Micro Computer (CPU & ROM) Driver DC Load
DC Controller has an LED, meaning that 5VDC is applied on this DC Controller safely. Generally the color of wiring is separated depends on the voltage. 0VDC Blue 5VDC Yellow 12VDC Brown 24VDC Orange Signal in to DC Controller (sensors) Purple Signal out from DC Controller Gray
CAUTION
There is a battery (CR2032) on the Motherboard of IPS Controller. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions. As for the waste disposal of battery, dispose in accordance with local state and federal relations.
4-2
K105sm4e1
4. 2
4. 2. 1
3 2
Item 1 2
3 4 5
PW5724B
PW5724B
Function Turning on and off the machine Detecting whether or not the Toner Hatch or the Engine Unit is opened. (It shuts off the AC power to the DCP1 when either of them is opened Outputting the high voltage to the Cleaning Roller. ON / OFF control of the Fuser Outputting the high voltage to each of the following components. (1) Image Corona (HV1) (2) Transfer Corona (HV2) (3) Separation Corona (HV3) (4) Developer Roller (OUTPUT2) (5) Regulation Roller (OUTPUT3) Avoiding the flicker of room lamp This board is used on 230V machine only.
4-3
K105sm4e1
NOTE
Developer Bias (OUTPUT 2 & 3) is outputted (or stopped) by the signal BIAS_TRG. The polarity of Bias is decided by the signal BIAS_SW
4-4
K105sm4e1
12
11
8 7
10 15
13
14
4-5
K105sm4e1
Item 7 8
Symbol DCP1 F1 F2 F3
Signal name -
Function Outputting each 24VDC, 5VDC and 0VDC Protecting the 24VDC from the over-current If you replace the fuses, make sure to use the following specified one. (Manufacturer) LITTEL FUSE INC. (Type) 02153 15MXP (250V / 3.15A) Protecting the circuit from the surge caused by the thunder Turning on and off the Dehumidify Heater ON / OFF control for the Dehumidify Heater (It makes the Dehumidify Heater OFF when the Main Switch is ON, and it makes the heater ON when the switch is OFF.) Supplying the power to the Lamp (H1). (It stops supplying the power to the Lamp when Switch (MS3) or Thermostat (TS1) is open.) Removing the noise from the AC line Used on 230V machine. Inputting the AC Power Used on 230V machine. Protecting the AC line from the over-current Used on 230V machine.
9 10 11
12
RY1
Relay
G7L-2A-TUB (DC24V)
13 14 15
RG-208F2
X28-XQ1A-10
4-6
K105sm4e1
4. 2. 2
Left side
3 2
Item 1
Signal name -
Function Overall sequence control (different on firmware save method) PW10522: Flash memory PW10520: EP ROM Driver for the motors, clutches and so on Detecting whether or not the Toner Hatch or the Engine Unit is opened (The machine does not shut off the AC power even if the MS4 detects either of them is opened.) Meeting the image head and leading edge of paper each other
2 3
PW6654B MS4
CL1
REGIST_CL
Clutch
MIC5NE-45
4-7
K105sm4e1
4. 2. 3
Back side
Item 1 2 3 4 5 6
Signal name -
MAMTR HEAT_M
DC Motor DC Motor
Function Assisting to transport the paper on the Inner Transport Unit Cooling down the IPS Controller Supplying the DC power to both the UI and the PW10523 Shutting down the IPS Controller. Driving the Drum, Developer Unit and paper feeding section Driving the Fuser Unit
4-8
K105sm4e1
7
Item 7 8 9 Symbol BL5 BL6 BL9 Signal name Name Fan Fan Fan
9
Type ASFN60372 ASFN60372 EUDC24B8
8
Function Controlling the temperature on the right area of Fuser Roller Controlling the temperature on the left area of Fuser Roller Controlling the temperature on the central area of Fuser Roller
4-9
K105sm4e1
10
Item 10
Symbol MS8
Signal name
Type FA2L-BA22
Function It stops supplying the AC power to the Dehumidify Heater when the Roll Deck is opened.
4-10
K105sm4e1
13 12
11
11
Item 11 12
13
MS3
Switch
V-162-1C25 10E
Function Exhausting the inside air. (They are equipped with the Ozone Filter.) Detecting whether or not the Heater Hatch is opened. (It shuts off the AC power to the DCP1 when the Heater Hatch is opened.) Detecting whether or not the Heater Hatch is opened. (The machine does not shut off the AC power even if the MS3 detects the Heater Hatch is opened.)
4-11
K105sm4e1
4. 2. 4
Front side
Item 1 2 3
Signal name
COUNT
Counter
Function Several kinds of message are indicated. Several kinds of service operations are available. Counting the total linear meter (linear foot) or square meter (square foot). It is possible to change the counting unit in the Service Mode.
4-12
K105sm4e1
4. 2. 5
Item 1
Symbol PW6631
Type PW6631
Function Removing the negative electric charges from the Drum at the beginning of the Print Process
4-13
K105sm4e1
Item 2 3
Signal name
Function Creating the Electrostatic Latent Image on the Drum Keeping the Grid Voltage constant (Control of the surface potential)
4-14
K105sm4e1
4. 2. 6
Main Frame
Item 1
Symbol PW6631
Type PW6631
Function Assisting the paper separation by removing the electric charges from the Drum at the time of Separation Process
4-15
K105sm4e1
Item 2
Symbol M4
Name DC Motor
Type DU2422-1
3 4 5
Function Pressing the Developer Unit to the Drum (Or keeping the Developer Unit away from the Drum) Detecting the Developer Unit is pressed or kept away Detecting the paper at the Registration Area Detecting the set of cut sheet paper
4-16
K105sm4e1
Item 6
Symbol MS5
Name Switch
Type CS1A-B2CA
4-17
K105sm4e1
4. 2. 7
Developer Unit
Item 1 2
Symbol TLS1 M3
Function Detecting whether or not the toner exists in the Developer Unit Driving the Toner Hopper to supply the toner to the Developer Unit
4-18
K105sm4e1
4. 2. 8
Fuser Unit
4 3
Item 1 2 3 4 Symbol TS1 TH2 TH1 TH3 Signal name Name Thermostat Thermistor 2 Thermistor Thermistor 3
2 1
Function Preventing over-heat Detecting the temperature on the right area of Fuser Roller Detecting the temperature on the central area of Fuser Roller Detecting the temperature on the left area of Fuser Roller
4-19
K105sm4e1
Item 5
Symbol H1
Signal name
PH3
HEAT_EXIT
Type
GP1A73A000J
4-20
K105sm4e1
4. 2. 9
Roll Deck
Item 1 2 3 4 5
Function Feeding the roll paper from both Roll 1 and Roll 2 Feeding the Roll 1 forward Rewinding the Roll 1 Feeding the Roll 2 forward Rewinding the Roll 2
4-21
K105sm4e1
Item 6 7
Signal name
Function Dehumidifying the roll paper Controlling the temperature of Resister (The Resisters turn on when the Thermostat detects some decided temperature, and they turn off when it detects another decided temperature.)
4-22
K105sm4e1
10
11
12
Item 8 9 10 11 12
Function Detecting the trailing edge of the roll paper Detecting the set of Roll 1 Detecting the set of Roll 2 Detecting paper end of Roll 1 Detecting paper end of Roll 2
4-23
K105sm4e1
4. 2.10
Cutter Unit
Item 1 2
Signal name
Type -
Function Moving the Cutter Blade Detecting the Home Position of Cutter Blade.
4-24
K105sm4e1
4. 2.11
Item 1
Symbol PH2
Name Sensor
Type GP1A73A000J
4-25
K105sm4e1
4. 2.12
Scanner Unit
NOTE
Components in Scanner Upper Unit may differ according to the time of manufacture. S/N 10512994 10513109, 10513137 and after Refer to this page. Before S/N 10512993, 10513110-10513136 Refer to page 4-28, 4-29. (10512994 10513109, 10513137 and after)
Item 1
Symbol
Signal name
Type
2 3 4
Function Data Controller Board makes several image processes to the digital data sent from the CIS Controller Board. And then it sends the processed image data to the controller. Converting the analog data read by the CIS to the digital data (installed to machines after S/N 10510001) Detecting whether or not the Scanner Upper Unit is opened.
4-26
K105sm4e1
Item 5
Symbol
Signal name
Type
6 7
Switch
CS1A-B2CA
Function Data Controller Board makes several image processes to the digital data sent from the CIS Controller Board. And then it sends the processed image data to the controller. Converting the analog data read by the CIS to the digital data Power Board converts the +24V to each +12V, +5V and +3.3V. Also it is the Driver Circuit of the Motor. Emergent stop button
4-27
K105sm4e1
Item 1
Symbol
Signal name
Type
2 3
Function Power Board converts the +24V to each +12V, +5V and +3.3V. Also it is the Driver Circuit of the Motor. Converting the analog data read by the CIS to the digital data Emergent stop button
4-28
K105sm4e1
Item 4
Symbol
Signal name
Type
5 6 7
Function Data Controller Board makes several image processes to the digital data sent from the CIS Controller Board. And then it sends the processed image data to the controller. Converting the analog data read by the CIS to the digital data Detecting whether or not the Scanner Upper Unit is opened. (installed to machines after S/N 10510001)
4-29
K105sm4e1
(Common Specification)
10
11
12
13
Item 8 9 10 11 12 13
Symbol
Signal name
Function It detects the insertion of original. Also it detects original widths A4, 11 and 12. It detects original widths A3, 17 and 18. It detects original widths A2, 22 and 24. It detects original widths A1 and 30. It detects original widths A0, 34 and 36. It detects the original mis-feed. It is also used to detect the leading edge when the original is returned.
4-30
K105sm4e1
14
14
Item 14
Symbol
Signal name
Type CIPS218CF601
Function CIS Units read the image of original, and then send the analog data to the CIS Controller Board
15
Item 15
Symbol
Signal name
Type
4-31
K105sm4e1
4. 3
4. 3. 1
It is necessary to check the analog output from High Voltage Power Supply after replacing the following parts. 1. PW10522 PCB (DC Controller) 2. HV Power Supply PCB (EUKG845HA) 3. HV Power Supply PCB (AHKG-067) Please check the analog output for each of the following part, and please adjust if it is out of the specified range. Each Reference page in the list shows how to check and adjust each item. Check Item Analog Voltage to the Image Corona Analog Voltage to the Transfer Corona AC Component to the Separation Corona DC Component to the Separation Corona Negative Developer Bias to the Developer Roller Positive Developer Bias to the Developer Roller Bias gap between Developer Roller and Regulation Roller Positive Cleaning Roller Bias (Print Cycle) Negative Cleaning Roller Bias (Toner Collection Process) Reference page 4-33 4-35 4-37 4-39 4-41 4-43 4-45 4-47 4-49
Reference
Please try to replace the PW10522 PCB or HV Power Supply PCB if you have the following kinds of problem. PW10522 PCB (1) When the UI indicates abnormal indication although the UI has no problem. (2) When the electric component such as motor or lamp does not work properly although such component has no problem. HV Power Supply PCB (EUKG845HA) (1) When the output to each Image Corona, Transfer Corona, Separation Corona Developer Roller, Toner Supply Roller and Regulation Roller is abnormal. HV Power Supply PCB (AHKG-067) (1) When the output to the Cleaning Roller is abnormal.
4-32
K105sm4e2_EUA
4. 3. 2
The standard value of the voltage outputted from the HV Power Supply PCB to the Image Corona is 1.30 +/-0.05V. Check and adjust the output current in the following way. 1. Connect the + cable of the multi-meter to the CP11 pin on the HV Power Supply PCB (EUKG845HA). Also connect the - one to the ground. And then, select the DC volt range on the multi-meter.
HV3
HV2
CP21
CP22
HV3
CP11
CP11 VR201
CAUTION!
HV2
VR101
6606600010
HV1
Multi-meter
VR402
Don't Touch
VR401
OUTPUT2
OUTPUT3
Ground
OUTPUT2
CP33
OUTPUT3 VR501
VR302 VR301
OUTPUT1
CN301
CN302
CN303
2. Make a Test Print making reference to [8. 8 Test Print Mode] on and after the page 8-143. As the high voltage is supplied to the Image Corona during the Test Print, check the voltage with the multi-meter. Standard value of the output voltage to the Image Corona is 1.30 +/-0.05V.
4-33
K105sm4e2_EUA
HV3DC
TP12
TN1
3. Adjust the output voltage if it does not satisfy 1.30 +/-0.05V. To adjust it, rotate the VR101 with a screwdriver.
HV3
HV2
CP21
CP22
HV3
CP11
VR201
CAUTION!
HV2
VR101
6606600010
HV1
VR101
Multi-meter
VR402 Don't Touch VR401
OUTPUT2
OUTPUT3
Ground
OUTPUT2
CP33
OUTPUT3 VR501
VR302 VR301
OUTPUT1
CN301
CN302
CN303
4-34
K105sm4e2_EUA
HV3DC
TP12
TN1
4. 3. 3
The standard value of the voltage outputted from the HV Power Supply PCB to the Transfer Corona is specified to each type of paper as follows. Plain paper Tracing paper Film 1.00 +/-0.05V 1.00 +/-0.05V 1.00 +/-0.05V
NOTE
The above values are just the standard values we have adjusted at the time of shipment. Of course you may change these values according to the usage condition.
1. Connect the + cable of the multi-meter to the CP21 pin on the HV Power Supply PCB (EUKG845HA). Also connect the - one to the CP22 pin. And then, select the DC volt range on the multi-meter. CP21
HV3
CP21
CP22
HV2
CP22
HV3
CP11
VR201
CAUTION!
HV2
VR101
9606660010
HV1
Multi-meter
VR402
Don't Touch
VR401
OUTPUT2
OUTPUT3
OUTPUT2
CP33
OUTPUT3 VR501
VR302 VR301
OUTPUT1
CN301
CN302
CN303
4-35
K105sm4e2_EUA
HV3DC
TP12
TN1
2. Select the Test Print Mode, and make a test print using each type of paper (plain paper, tracing paper & Film) making reference to [8. 8 Test Print Mode] on and after the page 8-143. As the high voltage is supplied to the Transfer Corona during the Test Print, check the voltage with the multi-meter. Standard values of the output voltages to the Transfer Corona are: Plain paper 1.00 +/-0.05V Tracing paper 1.00 +/-0.05V Film 1.00 +/-0.05V
3. Adjust the output voltage if it does not satisfy 1.00 +/-0.05V. Select the Adjustment Mode (Mode No.4), select each of following Sub Mode Numbers, and change the setting value so that the output voltage satisfies 1.00 +/-0.05V. (Refer to [8. 5. 4.12 Transfer Voltage (No.029 to 034)] on the page 8-47 for the detail.) Sub Mode No. 029 030 031 032 033 034 Contents Transfer Voltage (Plain paper) Transfer Voltage (Tracing paper) Transfer Voltage (Film) Transfer Voltage (Plain paper : Special) Transfer Voltage (Tracing paper : Special) Transfer Voltage (Film : Special)
4-36
K105sm4e2_EUA
4. 3. 4
The standard value of the AC Component outputted from the HV Power Supply PCB to the Separation Corona is 5.00 +/-0.05V. Check and adjust the AC Component in the following way. 1. Connect the + cable of the multi-meter to the CP31 pin on the HV Power Supply PCB (EUKG845HA). Also connect the - one to the CPCOM pin. And then, select the DC volt range on the multi-meter.
HV3 HV2 HV3
CP21
CP22
CP11
VR201
CAUTION!
HV2
VR101
9606660010
HV1
Multi-meter
VR402
Don't Touch
VR401
OUTPUT2
OUTPUT3
OUTPUT2
CP33
VR303 CP31
HV3DC
TP12
OUTPUT3 VR501
VR302 VR301
OUTPUT1
CP31
CN301
CN302
CN303
CPCOM
2. Make a Test Print making reference to [8. 8 Test Print Mode] on and after the page 8-143. As the high voltage is supplied to the Image Corona during the Test Print, check the voltage with the multi-meter. Standard value of the AC Component to the Separation Corona is 5.00 +/-0.05V.
4-37
K105sm4e2_EUA
HV3Frequency
HV3Vp- p
TN1
3. Adjust the AC Component if it does not satisfy 5.00 +/-0.05V. To adjust it, rotate the VR302 with a screwdriver.
HV3
HV2
CP21
CP22
HV3
CP11
VR201
CAUTION!
HV2
VR101
9606660010
HV1
Multi-meter
VR402
Don't Touch
VR401
OUTPUT2
OUTPUT3
OUTPUT2
OUTPUT3 VR501
VR302 VR301
OUTPUT1
CN301
CN302
CN303
4-38
K105sm4e2_EUA
CP31
HV3Frequency
HV3Vp- p
VR302
CP33
VR303
HV3DC
TP12
TN1
4. 3. 5
The standard value of the DC Component outputted from the HV Power Supply PCB to the Separation Corona is -250 +/-5V. Check and adjust the DC Component in the following way. 1. Connect the + cable of the multi-meter to the CP33 pin on the HV Power Supply PCB (EUKG845HA). Also connect the - one to the ground. And then, select the DC volt range on the multi-meter.
HV3
HV2
CP21
CP22
HV3
CP11
VR201
CAUTION!
HV2
VR101
9606660010
HV1
Multi-meter
VR402
Don't Touch
VR401
OUTPUT2
Ground
OUTPUT3
OUTPUT2
CP33
CP33
OUTPUT3 VR501
VR302 VR301
OUTPUT1
CN301
CN302
CN303
2. Make a Test Print making reference to [8. 8 Test Print Mode] on and after the page 8-143. As the high voltage is supplied to the Image Corona during the Test Print, check the voltage with the multi-meter. Standard value of the DC Component to the Separation Corona is -250 +/-5V.
4-39
K105sm4e2_EUA
HV3DC
TP12
TN1
3. Adjust the DC Component if it does not satisfy -250 +/-5V. To adjust it, rotate the VR303 with a screwdriver.
HV3
HV2
HV3
CP21
CP22
VR303
HV3DC
CP11
VR201
CAUTION!
HV2
VR101
9606660010
HV1
Multi-meter
VR402
Don't Touch
VR401
OUTPUT2
Ground
OUTPUT3
OUTPUT2
CP33
TP12
VR501
OUTPUT1
CN301
CN302
CN303
4-40
K105sm4e2_EUA
VR301
TN1
OUTPUT3
VR302
4. 3. 6
The Negative Developer Bias means the voltage supplied to the Developer Roller during the Print Cycle. The standard value of the Negative Developer Bias is as follows for each type of paper. Plain paper Tracing paper Film -230 +/-5V against the ground -230 +/-5V against the ground -230 +/-5V against the ground
Check and adjust the Negative Developer Bias in the following way.
NOTE
The above values are just the standard values we have adjusted at the time of shipment. Of course you may change these values according to the usage condition.
1. Connect the + cable of the multi-meter to the OUTPUT2 pin on the HV Power Supply PCB (EUKG845HA). Also connect the - one to the ground. And then, select the DC volt range on the multi-meter.
HV3
HV2
CP21
CP22
HV3
CP11
VR201
CAUTION!
HV2
VR101
9606660010
HV1
Multi-meter
VR402
Don't Touch
VR401
OUTPUT2
Ground
OUTPUT3
OUTPUT2
OUTPUT3 VR501
VR302 VR301
OUTPUT1
CN301
CN302
CN303
4-41
K105sm4e2_EUA
CP31
HV3Frequency
HV3Vp- p
OUTPUT 2
CP33
VR303
HV3DC
TP12
TN1
2. Make a Test Print making reference to [8. 8 Test Print Mode] on and after the page 8-143. As the Negative Developer Bias is supplied to the Developer Roller during the Test Print, check the voltage with the multi-meter. The standard value of the Negative Developer Bias for each type of media is: Plain paper Tracing paper Film -230 +/-5V against the ground -230 +/-5V against the ground -230 +/-5V against the ground
If the above values are not satisfied, go to the next step 8 for the adjustment. 3. Select the Adjustment Mode (Mode No.4), select each of following Sub Mode Numbers, and change the setting value so that the output voltage satisfies -230 +/-5V against the ground. (Refer to [8. 5. 4.10 Developer Bias (No.022 to 027)] on the page 8-46 for the detail.) Sub Mode No. 022 023 024 025 026 027 Contents Developer Bias (Plain paper) Developer Bias (Tracing paper) Developer Bias (Film) Developer Bias (Plain paper : Special) Developer Bias (Tracing paper : Special) Developer Bias (Film : Special)
4-42
K105sm4e2_EUA
4. 3. 7
The Positive Developer Bias means the voltage supplied to the Developer Roller during the Cleaning Cycle. The standard value of the Positive Developer Bias is +350 +/-5V against the ground. Check and adjust the Negative Developer Bias in the following way. 1. Connect the + cable of the multi-meter to the OUTPUT2 pin on the HV Power Supply PCB (EUKG845HA). Also connect the - one to the ground. And then, select the DC volt range on the multi-meter.
HV3
HV2
CP21
CP22
HV3
CP11
VR201
CAUTION!
HV2
VR101
9606660010
HV1
Multi-meter
VR402
Don't Touch
VR401
OUTPUT2
Ground
OUTPUT3
OUTPUT2
OUTPUT3 VR501
VR302 VR301
OUTPUT1
CN301
CN302
CN303
4-43
K105sm4e2_EUA
CP31
HV3Frequency
HV3Vp- p
OUTPUT 2
CP33
VR303
HV3DC
TP12
TN1
2. Make a Test Print making reference to [8. 8 Test Print Mode] on and after the page 8-143. The Positive Developer Bias is supplied to the Developer Roller for some seconds after the printed paper has been ejected. Check the voltage with the multi-meter during that period. The standard value of the Positive Developer Bias is +350 +/-5V against the ground. If this is not satisfied, go to the next step 8 for the adjustment.
3. Adjust the Positive Developer Bias rotating the VR401, so that it should satisfy +350 +/-5V against the ground.
HV3
HV2
CP21
CP22
HV3
CP11
VR201
CAUTION!
HV2
VR101
9606660010
HV1
Multi-meter
VR402
Don't Touch
VR401
VR401
OUTPUT2
Ground
OUTPUT3
OUTPUT2
CP33
OUTPUT3 VR501
VR302 VR301
OUTPUT1
CN301
CN302
CN303
4-44
K105sm4e2_EUA
HV3DC
TP12
TN1
4. 3. 8
Check & Adjustment of the Bias gap between Developer Roller and Regulation Roller
The standard value of the Bias gap between Developer Roller and Toner Supply Roller is 40 +/-5V. Check and adjust it in the following way. 1. Connect the + cable of the multi-meter to the OUTPUT3 pin on the HV Power Supply PCB (EUKG845HA). Also connect the - one to the OUTPUT2 Pin. And then, select the DC volt range on the multi-meter.
HV3
HV2
CP21
CP22
HV3
CP11
VR201
CAUTION!
HV2
VR101
9606660010
HV1
Multi-meter
VR402
Don't Touch
VR401
OUTPUT2
OUTPUT 3
OUTPUT3
OUTPUT2
CP33
OUTPUT 2
OUTPUT3 VR501 VR302 VR301
OUTPUT1
CN301
CN302
CN303
2. Make a Test Print making reference to [8. 8 Test Print Mode] on and after the page 8-143. As the Bias is supplied to both the Developer Roller and the Toner Supply Roller, check the Bias gap between them with the multi-meter. The standard value of the Bias gap between Developer Roller and Regulation Roller is 40 +/-5V.
4-45
K105sm4e2_EUA
HV3DC
TP12
TN1
3. Adjust the Bias gap if it does not satisfy 40 +/-5V. To adjust it, rotate the VR501 with a screwdriver.
HV3
HV2
CP21
CP22
HV3
CP11
VR201
CAUTION!
HV2
VR101
9606660010
HV1
Multi-meter
VR402
Don't Touch
VR401
OUTPUT2
OUTPUT3
OUTPUT2
CP33
OUTPUT3 VR501
VR302 VR301
VR501
VR601 OUTPUT1 CPCOM
OUTPUT1
CN301
CN302
CN303
4-46
K105sm4e2_EUA
HV3DC
TP12
TN1
4. 3. 9
The Positive Cleaning Roller Bias means the voltage supplied to the Cleaning Roller during the Print Process. The standard value of the Positive Cleaning Roller Bias is +450 +/-5V. Check and adjust it in the following way. 1. Connect the + cable of the multi-meter to the OUTPUT pin on the HV Power Supply PCB (AHKG-067). Also connect the - one to the ground. And then, select the DC volt range on the multi-meter.
2. Make a Test Print making reference to [8. 8 Test Print Mode] on and after the page 8-143. As the Positive Cleaning Roller Bias is supplied during the Test Print, check the voltage value with the multi-meter. Standard value of the Positive Cleaning Roller Bias is +450 +/-5V.
OUTPUT
VR2
Multi-meter
(DC volt range)
CN501
Ground
4-47
K105sm4e2_EUA
3. Adjust the Positive Cleaning Roller Bias if it does not satisfy +450 +/-5V. To adjust it, rotate the VR2 with a screwdriver.
Multi-meter
(DC volt range)
CN501
VR2
Ground
4-48
K105sm4e2_EUA
4. 3.10
Check & Adjustment of Negative Cleaning Roller Bias (Toner Collection Process)
The Negative Cleaning Roller Bias means the voltage supplied to the Cleaning Roller during the Toner Collection Process, which is done after the completion of Print Process. The standard value of the Negative Cleaning Roller Bias is -550 +/-5V. Check and adjust it in the following way. 1. Connect the + cable of the multi-meter to the OUTPUT pin on the HV Power Supply PCB (AHKG-067). Also connect the - one to the ground. And then, select the DC volt range on the multi-meter.
2. Make a Test Print making reference to [8. 8 Test Print Mode] on and after the page 8-143. The Toner Collection Process works for some seconds after the printed paper has been ejected. Check the voltage value with the multi-meter during that period. Standard value of the Negative Cleaning Roller Bias is -550 +/-5V.
OUTPUT
VR2 CN501
Multi-meter
(DC volt range)
Ground
4-49
K105sm4e2_EUA
3. Adjust the Negative Cleaning Roller Bias if it does not satisfy -550 +/-5V. To adjust it, rotate the VR1 with a screwdriver.
Multi-meter
(DC volt range)
CN501
Ground
4-50
K105sm4e2_EUA
Chapter 5 Mechanical
5. 1 Outer Covers 5. 1. 1 Removal of Side Covers 5. 1. 2 Removal of Cover 15 5. 1. 3 Removal of Cover 14 5. 2 Developer Unit 5. 2. 1 Removal of the Developer Unit 5. 2. 2 Replacement of Developer Unit Components 5. 2. 3 Replacement of DC Motor 5. 2. 4 Replacement of Sensor (TLS1) 5. 2. 5 Adjustment of the space between gears (Necessary to adjust after replacing the Developer Unit) 5. 2. 6 Readjustment of the pressure of Regulation Roller 5. 3 Fuser Unit 5. 3. 1 Removal of the Fuser Unit 5. 3. 2 Replacement of Fuser Unit Components 5. 3. 3 Replacement of Roller Pressure 5. 3. 4 Replacement of Thermistors 5. 3. 5 Replacement of Thermostat 5. 3. 6 Replacement of Exit Sensor 5. 4 Roll Deck 5. 4. 1 Replacement of Cutter Assembly 5. 4. 2 Replacement of Clutches (CL3, CL4 & CL5) of Roll 1 5. 4. 3 Replacement of Clutches (CL6 & CL7) of Roll 2 5. 4. 4 Replacement of Timing Belt (480) for Roll 2 5. 4. 5 Replacement of Timing Belt (480) for Roll 1 5. 4. 6 Replacement of Timing Belt (330) 5. 4. 7 Replacement of Timing Belt (753) 5. 4. 8 Replacement of Sensors (PH6, PH7 & PH9) 5. 4. 9 Replacement of Sensors (PH8 & PH10) 5. 4.10 Replacement of Dehumidify Heater 5. 4.11 Installation of Roll Deck 2 Kit (Optional for USA) 5. 4.12 Removal of Roll Deck 2 5. 5 Photoconductive Drum 5. 5. 1 Replacement of the Photoconductive Drum 5. 5. 2 How to fix the Aluminium Blocks 5. 5. 3 Cleaning of Photoconductive Drum 5. 5. 4 Replacement of Belt 4
Page 5- 3 5- 3 5- 5 5- 6 5- 8 5- 8 5-11 5-33 5-35 5-36 5-42 5-44 5-44 5-47 5-61 5-69 5-71 5-72 5-73 5-73 5-78 5-82 5-85 5-89 5-92 5-93 5-95 5-99 5-104 5-106 5-120 5-139 5-139 5-147 5-151 5-152
5-1
K105sm5e1_EUA
5. 6 LED Head 5. 6. 1 Replacement of the LED Head Unit 5. 6. 2 LED focus adjustment 5. 6. 2. 1 Check of the Test Pattern Image 5. 6. 2. 2 Positioning of the Aluminium Blocks 5. 6. 2. 3 Focus Adjustment with Spacers 5. 7 Image Corona 5. 7. 1 Removal of the Image Corona Unit 5. 7. 2 Replacement of the Corona Wire 5. 8 Transfer / Separation Corona 5. 8. 1 Removal of the Transfer / Separation Corona 5. 8. 2 Replacement of Corona Wires 5. 9 Engine Frame 5. 9. 1 Replacement of DC Motor (M4) and Developer Press Sensor (PH4) 5. 9. 2 Replacement of Manual Set Sensor (PH5) & Registration Sensor (PH1) 5. 9. 3 Replacement of Fans (BL5 & BL6) 5. 9. 4 Replacement of Blowers (BL3 & BL4) 5.10 Inner Transport Unit 5.10. 1 Removal of the Inner Transport Unit 5.10. 2 Replacement of Sensor (PH2) & Belt 5.11 Main Frame 5.11. 1 Replacement of DC Motors (M1 & M2), Belt1 & Belt 3 5.11. 2 Replacement of Clutch (CL1) 5.11. 3 Replacement of Blower (BL7) 5.12 Scanner Unit 5.12. 1 Removal of the Scanner Unit 5.12. 2 Replacement of Motor Assembly 5.12. 3 Replacement of Belt 60S2M250 and Belt 60S2M284 5.12. 4 Replacement of Drive Rollers 1 and 2 5.12. 5 Removal of Base Plate 5.12. 5. 1 Removal of Base Plate (10512994 10513109, 10513137 and after) 5.12. 5. 2 Removal of Base Plate (before S/N 10512993, 10513110-10513136) 5.12. 6 Replacement of CIS Assembly 5.12. 7 Replacement of Gap Roller
5-154 5-154 5-162 5-162 5-163 5-172 5-178 5-178 5-185 5-190 5-190 5-192 5-195 5-195 5-199 5-201 5-202 5-204 5-204 5-206 5-210 5-210 5-218 5-221 5-222 5-222 5-229 5-232 5-235 5-253 5-253 5-258 5-263 5-265
5-2
K105sm5e1_EUA
5. 1
5. 1. 1
Outer Covers
Removal of Side Covers
5-3
K105sm5e1_EUA
4. Remove 5 pieces of screw (4) at both sides. (2 pieces on the right and 3 pieces on the left)
4 4
5-4
K105sm5e1_EUA
5. 1. 2
Removal of Cover 15
1
1. Remove 4 screws (1), loosen 4 screws (2), and remove the Cover 15 (3).
5-5
K105sm5e1_EUA
5. 1. 3
Removal of Cover 14
1
2. Loosen 4 pieces of screw (2) on the back, and remove 4 pieces of screw (3) on the front. 2 3
5-6
K105sm5e1_EUA
5-7
K105sm5e1_EUA
5. 2
5. 2. 1
Developer Unit
Removal of the Developer Unit
2. Remove the 4x6 screws and washers (2) at both sides to make the Bands (3) free.
2 3
2 3
5-8
K105sm5e2_EUA
3. There are Pins (4) at both sides. Pull them up and then slide them inward to remove the Cover 4 (1).
5-9
K105sm5e2_EUA
7. Close the Bypass Feeder, and then open the Developer Press Unit (8).
8. Holding both Side Plates (9), remove the Developer Unit (10) from the machine. 9
10
NOTE
If you replace the whole Developer Unit, it is necessary to adjust the space between developer driving gears. Refer to [5. 2. 5 Adjustment of the space between gears (Necessary to adjust after replacing the Developer Unit)] on the page 5-36.
5-10
K105sm5e2_EUA
5. 2. 2
(1)
The following parts are Developer Unit components. A periodic replacement for the following parts is recommended. This section describes how to replace all of them in one sequent operation. Item Roller Developer Sheet 3 Sheet 4 Seal 1 Seal 3 Seal 4 Scraper Toner Supply Roller Sheet 5 Sheet 6 Number of article 1 2 2 2 2 2 1 1 2 2 Remarks All of these parts are contained in Developer Maintenance Kit E (Z050980280).
(2)
Remove all the toner from Developer Unit before replacing the above parts.
1. Remove the Developer Unit from the machine making reference to [5. 2. 1 Removal of the Developer Unit] on the page 5-8.
5-11
K105sm5e2_EUA
3. Remove 4 pieces of 4x6 screws (2) which fix the Hopper Assembly. 2
5-12
K105sm5e2_EUA
6. Remove 4 pieces of 4x6 screw (6), and then remove the Scraper Assembly (7).
6 6
5-13
K105sm5e2_EUA
7. Remove 10 pieces of screw (8), and then disassemble the Scraper Assembly. Replace the Scraper (9) with the new one.
8 8
NOTE
(1) Please install the new Scraper so that one of its 4 edges pointed by an arrow mark should touch the surface of Regulation Roller. (2) The edge must be straight after the installation. Otherwise the toner will not be scraped off well. Arrow mark (3) Carry Scraper Assembly ends so that the touching edge to Regulation Roller is in downward direction. 10
If Scraper falls or slips, Seal 5 (P/N: Z054601260) should be applied on Bracket 14 (10) so that Scraper Assembly housing catches Scraper firmly.
NOTE
Do not reuse the removed toner.
5-14
K105sm5e2_EUA
11
NOTE
The Bracket 4 (12) is moved up by the spring if you loosen the screws (11). The Blade Roller (13) is released at this time.
12 11
13
11
When reassemble, make sure to tighten the screws (11) with pressing the Bracket 4 (12) fully to the arrow direction.
12 11
13
11
5-15
K105sm5e2_EUA
10. Remove 4 pieces of 4x6 screws (14), 1 piece of 4x8 screw (15) and Pin 4 (16). Also remove the Bracket 9 (17) and Collar (18).
14
15 14
18
17 16
11. Remove the Retaining Ring-E (19 : E7) to remove Thrust Washer (20 : 8.1x14x0.5) and Gear Helical 28T (21). 19
21 20 19 5-16
K105sm5e2_EUA
12. Remove the Retaining Ring-E (22 : E5) to remove Gear Helical 25T (23), Parallel Pin (24 : 2.5 x 12) and Collar 3 (25) from the shaft of Blade Roller. Also remove the Gear Helical 30T (26) and Parallel Pin (27 : 3x14) from the shaft of Roller Supply.
22
25 24 23 22 27
26
5-17
K105sm5e2_EUA
13. Remove the Retaining Ring-E (28 : E7) to remove Thrust Washer (29 : 8.1x14x0.5) and Gear Helical 28T Assembly (30).
30 29 28
28
14. Remove 2 pieces of 3x6 screw (31) to remove the Holder 2 Assembly (32).
32 31
5-18
K105sm5e2_EUA
15. Loosen 2 pieces of 4x6 screw (33) to release the Blade Roller.
33
NOTE
The Bracket 5 (34) is moved up by the spring if you loosen the screws (35). The Blade Roller (13) is released at this time. 34
13 35 35
When reassemble, make sure to tighten the screws (35) with pressing the Bracket 5 (34) fully to the arrow direction. 34 13 35
35
5-19
K105sm5e2_EUA
16. Remove 3 pieces of 4x6 screw (36) and 2 pieces of Retaining Ring-E (37 : E10). Then, remove the Collars (38) and the Bracket 10 Assembly (39).
37
36
36
39
38
38
5-20
K105sm5e2_EUA
17. Remove the Gear Helical 32T (40), the Thrust Washer (41:12.1x20x0.2), the Gear Helical 24T (42) and the Parallel Pins (43 : 3x16).
42
43
41 40 40 41
42
18. Remove the Retaining Ring-E (44 : E10) to remove Thrust Washer (45 : 12.2x20x0.5) and Counter Roller (46) on the driving side.
46 44 45 44
19. Also remove the Counter Roller (47) on the electrode plate side.
47 47
5-21
K105sm5e2_EUA
20. Remove the Retaining Ring-E (48 : E10) and the Thrust Washers (49 : 12.2x20x0.5). Remove 3 pieces of 4x6 screw(50) to remove the Bracket 8 Assembly (51).
50 48
51 49 50
50
48
21. Remove the Retaining Ring-E (52 : E10) to remove the Thrust Washer (53 : 12.2x20x0.5) and the Bearing (54).
52
54 53 52
5-22
K105sm5e2_EUA
22. Remove the Roller Developer (55), and replace it with the new one. Paste the Sheet 3 (56 : outside) and Sheet 4 (57 : inside / with double-face tape) to both side faces of Roller Developer at this time.
55
55
56
57
NOTE
You need to care about the direction of Roller Developer. The Electrode Plate side has 3 ditches on the shaft, and the driving side has 2 ditches. 3 ditches 2 ditches
Driving side
5-23
K105sm5e2_EUA
23. Remove 2 pieces of 4x6 screw (11) to remove the Bracket 4 (12) and the Spring (58).
11
12
58
5-24
K105sm5e2_EUA
24. Remove 2 pieces of 4x6 screw (35) to remove the Bracket 5 (34) and the Spring (56).
35
34
59
25. Remove the 4x8 Pan Head screw (60) to remove the Flat Washer (61 : M4) and the Bracket 6 Assembly (62)
60
61 60 62
5-25
K105sm5e2_EUA
26. Remove the Retaining Ring-E (63 : E8) to remove the Thrust Washers (59 : 10.1x16x0.5)(64) and Bracket 7 Assembly (65) on the Electrode Plate side.
63 65 64 63
27. Remove 2 pieces of 4x6 screw (66) to remove the Bracket 19 (67).
66
67
5-26
K105sm5e2_EUA
68
68
NOTE
You need to care about the direction of Blade Roller. The longer shaft should be on the driving side.
Driving side
5-27
K105sm5e2_EUA
29. Remove the Seals 1 (69) at both sides. Replace the Seals 1 (69) with the new ones. 69
30. Remove the Retaining Ring-E (70 : E10) to remove Thrust Washer (71 : 12.2x20x0.5) and Bearing (72) on the driving side.
70 72 71 70
31. Remove the Retaining Ring-E (73 : E10) to remove Thrust Washer (74 : 12.2x20x0.5) and Bearing (75) on the Electrode Plate side.
73 75 74 73
5-28
K105sm5e2_EUA
32. Turn the whole Developer Unit to the arrow mark so that you can see the bottom of the unit.
33. Remove 2 pieces of 4x6 screws (76) to remove the Bracket Assembly (77).
77 76
34. Remove 9 pieces of 4x6 screws (78) to remove the Frame 2 (79). 78 78
79 78
5-29
K105sm5e2_EUA
35. Remove the Roller Supply (80) sliding to the arrow direction, and replace it with the new one. Paste the Sheet 5 (81 : outside) and Sheet 6 (82 : inside / with double-face tape) to both side faces of Toner Supply Roller at this time.
80 80 81
82
NOTE
(1) You need to care about the direction of Roller Supply. The Electrode Plate side has 2 ditches on the shaft, and the driving side has 3 ditches. 2 ditches 3 ditches
Electrode Plate side (2) There are Seal 4 (85) at both sides of the Roller Supply. Remove them from the old Roller Supply and then install them to the new Roller Supply. (Be careful not to dispose them.)
Driving side
83
5-30
K105sm5e2_EUA
36. Remove the 4x8 tapping screws (84) and 4x8 bind screws (85) at both sides, and remove each Seal L Assembly (86), Seal R Assembly (87) and Collars (88).
86 86
85 85 84 84 88
87 87
88 84 85 84 85
NOTE
When you reinstall both the Seal L Assembly (86), Seal R Assembly (87), do not tighten the 4x8 tapping screws (84) so much as the seals will be transformed as the following bad example.
Seal is transformed.
Seal is straight.
Good example
K105sm5e2_EUA
37. There are Seals 3 (89) and Seals 4 (90) at both sides. Strip them off, and replace them with the new ones.
90
89
89
90
NOTE
Align both the Seals 3 (89) and Seals 4 (90) at the bottom side.
Alignment
5-32
K105sm5e2_EUA
5. 2. 3
Replacement of DC Motor
1
2. Disconnect the connector (3), remove 2 pieces of 4x6 screw (4), and then remove the motor assembly. 4
5-33
K105sm5e3_EUA
4. Remove 3 pieces of 3x20 screw (7) to remove the Bracket 19 (8). Replace the DC Motor (9) with the new one.
5-34
K105sm5e3_EUA
5. 2. 4
1. Remove the Developer Unit (1) from the machine making reference to [5. 2. 1 Removal of the Developer Unit] on the page 5-8.
2. Disconnect the connector (2), and then remove 2 pieces of 3x6 screw (3) to remove the Sensor (4). Replace the Sensor (4) with the new one.
2 4 3
5-35
K105sm5e3_EUA
5. 2. 5
Adjustment of the space between gears (Necessary to adjust after replacing the Developer Unit)
NOTE
You do not have to adjust the space between gears basically as it has been adjusted in the factory. But please do it only when you replace the whole Developer Unit. The Developer Unit is driven by the Gear Helical 34T on the machine and the Gear Helical 28T on the Developer Unit. There must be a little mechanical play between these gears. (In another word there must be a little space between them.)
If there is no space between these gears, the gear may be broken. In this case it is necessary to add Adjustment Plates to keep a space. Not correct Correct
Add Adjustment Plates. There is not enough space between gears. (Gears may be broken) Refer to the next page how to add the Adjustment Plates. 5-36
K105sm5e3_EUA
1. Remove the Developer Unit (1) from the machine making reference to [5. 2. 1 Removal of the Developer Unit] on the page 5-8.
2. Remove 2 screws (2) to remove each Bracket 32 (3) on the left and Bracket 33 (4) on the right. You will find Adjustment Plate (5) and Adjustment Plate 2 (6).
5 3
6 4
5-37
K105sm5e3_EUA
3. On the left side, add (or remove) as many Adjustment Plate (5) as required, cover them with the Bracket 32 (3) and then fix with 2 screws (2).
NOTE
The following 3 kinds of Spacers are used on the left side of the machine. Spacer Spacer 5 Spacer 3 Z053101200 (thickness is 0.05mm) Z053101350 (0.1mm) Z053101330 (0.2mm)
5-38
K105sm5e3_EUA
4. On the right side, add (or remove) as many Adjustment Plate 2 (6) as required, cover them with the Bracket 33 (4) and then fix with 2 screws (2).
NOTE
The following 3 kinds of Spacers are used on the left side of the machine. Spacer 2 Spacer 6 Spacer 4 Z053101210 (thickness is 0.05mm) Z053101360 (0.1mm) Z053101340 (0.2mm)
5-39
K105sm5e3_EUA
6. There is the Gear Helical 28T (7) on the Developer Unit side, and also there is the Gear Helical 34T (8) on the machine side. (They are contacted each other when the Developer Unit is on the machine.) (The bottom of the Engine Unit)
Holding the Gear Helical 28T (7) firmly with one hand, move the Gear Helical 34T (8) with another hand whether there is any mechanical play between these gears. Hold the Gear Helical 28T with one hand.
5-40
K105sm5e3_EUA
7. There must be a little mechanical play between Gear Helical 28T (7) and Gear Helical 34T (8). (In another word there must be a little space between them.) If the gear could not be moved at all when you check them on the former procedure 6, it means there is not enough space between gears. The gear may be broken in this case. In this case, add more Adjustment Plates by the way instructed at the procedures 3 and 4.
Add Adjustment Plates There is not enough space between gears. (Gears are not movable) The space between gears becomes wider. (Gears become movable)
5-41
K105sm5e3_EUA
5. 2. 6
If the pressure of Regulation Roller is weak, the toner layer on the Developer Unit will be much thicker than required when you rotate the Developer Roller in the above procedure 27. Pressurize the Regulation Roller in the correct way as shown below in this case. (You will not be able to pressurize it successfully by the usual way of pressurization.) 1. On the right side (Electrode Plate side) of the unit, press and hold the Bracket 5 (1) to the arrow direction completely, and fix it with the screws (2). 1
2. On the left side of the unit (gear side), confirm that the Bracket 4 (3) is fixed with the screws (4) being completely pressed to the arrow direction. Also confirm that the screw (5) is loosened and the Gear Helical 20T (6) is installed. 3 4 4 5
3. Fully press down and hold the top of the Bracket 6 (7). With holding, rotate the Developer Roller twice with the Developer Handle (8). Check that the toner layer on the Developer Roller gets thinner. 7 7
5-42
K105sm5e3_EUA
4. Remove both the Retaining Ring-E (9) and the Gear Helical 20T (6).
9 6&9 6
6. Reinstall the Gear Helical 20T (6) and the Retaining Ring-E (9).
9 6 6&9
5-43
K105sm5e3_EUA
5. 3
5. 3. 1
Fuser Unit
Removal of the Fuser Unit
5-44
K105sm5e4_EUA
5. There are 2 pieces of Bracket (5) on the back of the machine. Remove the upper 4x6 screw (6) and loosen the lower 4x6 screw (7), then turn the Bracket (5) as the following photo.
7 5
5-45
K105sm5e4_EUA
NOTE
It is impossible to remove the Fuser Unit if the Engine Unit is open.
5-46
K105sm5e4_EUA
5. 3. 2
NOTE
The following parts are Fuser Unit components. A periodic replacement for them is recommended. This section describes how to replace all of them in one sequent operation. Roller Fusing Bush Nail Stripping (Upper) Nail Lower 1 2 13 6 All of these parts are contained in Fuser Maintenance Kit (Z050980060)
5-47
K105sm5e4_EUA
5-48
K105sm5e4_EUA
6. Remove the 4x6 screw (6) to remove the Plate 2 (7) on the right of machine.
NOTE
(1) Please remove the Plate 2 (7) while holding the Cover Assembly. Otherwise you may drop the Cover Assembly. (2) There is the Plate on the left side of machine, which is a symmetric part of Plate 2. You may remove it instead of Plate 2 (7).
5-49
K105sm5e4_EUA
8. Remove the 4x6 screw (8) to remove each Nail Stripping Assembly (9). 9
9. Disassemble the Nail Stripping Assembly as the following photo. Replace the Nail Stripping (10) with the new one.
10
10. There are 2 pieces of Bracket (11) on the back of the machine. Remove the upper 4x6 screw (12) and loosen the lower 4x6 screw (13), then turn the Bracket (11) as the following photo.
12
11
13
11
5-50
K105sm5e4_EUA
NOTE
It is impossible to remove the Fuser Unit if the Engine Unit is open.
14
14
5-51
K105sm5e4_EUA
13. Loosen the 4x6 screw (15) and then remove the Cover 4 (16) on the connector side. (Connector side)
16
15
16
14. Loosen the 4x6 screw (17) and then remove the Cover 5 (18) on the connector side. (Gear side)
18 18 17
NOTE
Make sure to fit the hook (19) of each Cover 4 (16) and Cover 5 (18) to the notch (20) when reassemble. 19
20
5-52
K105sm5e4_EUA
15. Disconnect the connectors (21) at both sides. Remove the 4x6 screws (22) to remove the Heater Lamp Holders (23) (Connector side) 22
21
23
(Gear side) 22
21
23
5-53
K105sm5e4_EUA
24
24
NOTE
(1) You do not have to care about the direction (left and right) of the Lamp. (2) Do not touch the glass part of the Lamp with bare hand.
17. Open the Wire Saddle (25) to release the wires. (Connector side)
25
18. Remove the 3x6 screw (26) to release the Holder 5 (27). (Connector side)
26
27
5-54
K105sm5e4_EUA
19. Loosen the 4x6 screw (28) on the connector side to release the Cover 2 (29). (Connector side)
28
29
20. Also loosen the 4x6 screw (30) on the gear side to release the Cover 1 (31). (Gear side)
30
31
5-55
K105sm5e4_EUA
21. Remove the 4x6 screw (32) to remove the Bracket 6 (33) on the connector side. (Connector side)
33
32
22. Remove the 4x6 screw (34) to remove the Bracket 5 (35) on the connector side. (Gear side)
34
35
NOTE
When reassemble, make sure to slide each Bracket 6 (33) and Bracket 5 (35) fully to the arrow direction. The folded plate part (36) must be fitted into the notch as the right photo. Notch
36 5-56
K105sm5e4_EUA
23. Open the Fuser Upper Unit (37), and then bring it up to separate from the Fuser Lower Unit.
37
37
37
24. Remove the Retaining Ring-E (38 : E7) to remove the Gear 28T (39).
38
39
5-57
K105sm5e4_EUA
25. On the gear side, remove the KL Clip (40) and then remove Pin 11 (41), Gear 48T (42) and Bush (43). Replace the Bush (43) with the new one. (Gear side) 40
41
43 42
26. On the connector side, remove 2 pieces of 4x6 screw (44) to remove Collar (45) and Bush (46). Replace the Bush (47) with the new one. (Connector side)
44
44
46
45
NOTE
Please fit the projected part (47) of the Bush to the notch (48) at the time of reassembly.
47
48
5-58
K105sm5e4_EUA
27. Remove the Roller Fusing (49), and replace it with the new one.
49
NOTE
You do not have to care about the direction (left and right) of the Roller Fusing.
50
50
5-59
K105sm5e4_EUA
30. Remove the 4x6 screw (52) to remove each Nail Lower Assembly (53). 52 53
31. Rotate the Nail Lower (54) quarter evolution, and then remove it from the bracket. Replace the Nail Lower (54) with the new one.
54
5-60
K105sm5e4_EUA
5. 3. 3
5-61
K105sm5e5_EUA
6. Remove the 4x6 screw (6) to remove the Plate 2 (7) on the right of machine.
NOTE
(1) Please remove the Plate 2 (7) while holding the Cover Assembly. Otherwise you may drop the Cover Assembly. (2) There is the Plate on the left side of machine, which is a symmetric part of Plate 2. You may remove it instead of Plate 2 (7).
5-62
K105sm5e5_EUA
8. There are 2 pieces of Bracket (8) on the back of the machine. Remove the upper 4x6 screw (9) and loosen the lower 4x6 screw (10), then turn the Bracket (8) as the following photo.
10
5-63
K105sm5e5_EUA
NOTE
It is impossible to remove the Fuser Unit if the Engine Unit is open. 10. Remove the Fuser Unit (11) from the machine.
11
11
11. Open the Wire Saddle (12) to release the wires. (Connector side)
12
5-64
K105sm5e5_EUA
12. Remove the 3x6 screw (13) to release the Holder 5 (14). (Connector side) 14
13
14
13. Remove the 4x6 screw (15) to remove the Bracket 6 (16) on the connector side. (Connector side)
16
15
5-65
K105sm5e5_EUA
14. Remove the 4x6 screw (17) to remove the Bracket 5 (18) on the connector side. (Gear side)
17
18
NOTE
When reassemble, make sure to slide each Bracket 6 (16) and Bracket 5 (18) fully to the arrow direction. The folded plate part (19) must be fitted into the notch as the right photo.
Notch
19 15. Open the Fuser Upper Unit (20), and then bring it up to separate from the Fuser Lower Unit.
20
20
19
5-66
K105sm5e5_EUA
21
21
22
5-67
K105sm5e5_EUA
18. Remove the 4x6 screws (23) to remove the Guide Plate (24). 24
23
23
NOTE
4x6 screws (23) are attached with the Collar (25).
25
26
19. Remove the Retaining Ring-C (27 : C15) to remove the Collars (28) and Bearings (29) from both sides. Replace the Roller Pressure (30) with the new one. 27
30
28
29
5-68
K105sm5e5_EUA
5. 3. 4
Replacement of Thermistors
1. Remove the Fuser Unit (1) from the machine making reference to [5. 3. 1 Removal of the Fuser Unit] on the page 5-44.
2. Remove the Clump (2) removing the 4x6 screw. Also open the Wire Saddle (3) to release the wires.
4 5
4. Remove 3 pieces of Wire Stopper Brackets (6) removing 1 piece of 4x6 screw for each.
5-69
K105sm5e5_EUA
5. Remove the 4x6 screw (7) to remove each Bracket Assembly (8) with Thermistor.
6. Remove the 3x8 screw (9) to remove the Thermistor (10). Replace the Thermistor (10) with the new one.
9 10
NOTE
Be careful of the direction of Thermistor when reassemble. The projection (11) nearer to the harness should be inserted to the positioning hole (12). 11 12
5-70
K105sm5e5_EUA
5. 3. 5
Replacement of Thermostat
1. Remove the Fuser Unit (1) from the machine making reference to [5. 3. 1 Removal of the Fuser Unit] on the page 5-44.
2. Remove 2 pieces of 3x6 screw (2) to remove the Holder (3) with the Thermostat.
3 2
3. Remove 2 pieces of 3x4 screw (4) to remove the Thermostat (5). Replace the Thermostat (5) with the new one.
5 4
5-71
K105sm5e5_EUA
5. 3. 6
5-72
K105sm5e5_EUA
5. Remove the 4x6 screw (5) to remove the Plate 2 (6) on the right of machine.
NOTE
(1) Please remove the Plate 2 (6) while holding the Cover Assembly. Otherwise you may drop the Cover Assembly. (2) There is the Plate on the left side of machine, which is a symmetric part of Plate 2. You may remove it instead of Plate 2 (6).
5-73
K105sm5e5_EUA
7. Disconnect the connector (7), and then remove the screw (8) to remove the Exit Sensor Assembly (9). 7
8. Pressing the stoppers (10) inside, remove the Exit Sensor (11) from the bracket. Replace the Exit Sensor (11) with the new one. 11
10
5-74
K105sm5e5_EUA
5. 4
5. 4. 1
Roll Deck
Replacement of Cutter Assembly
5-73
K105sm5e6_EUA
NOTE
Make sure to insert the hooking part (4) to the slit as the following photo when you put back the Cover 1 (3).
5-74
K105sm5e6_EUA
NOTE
(1) Be careful not to catch the wires of Cutter Motor when you put back the Cover 3 (6).
(2) Make sure that the step part (7) on the lower side of the Cover 3 (6) is inside of the plate (8). 7
5-75
K105sm5e6_EUA
10
10
5-76
K105sm5e6_EUA
8. Remove the Cutter Assembly (11), and then replace it with the new one.
11
NOTE
(1) Put the Cutter Assembly with the Cutter Motor up. If you put it with the Cutter Motor down, you will break the Cutter Motor Harness.
(2) There is the Height Guide (12) on the right side. Please fix the Cutter Assembly aligning the plate (13) and the central line of Height Guide (12) each other.
13
12
5-77
K105sm5e6_EUA
5. 4. 2
5-78
K105sm5e6_EUA
NOTE
Make sure to insert the hooking part (4) to the slit as the following photo when you put back the Cover 1 (3).
5-79
K105sm5e6_EUA
NOTE
(1) Be careful not to catch the wires of Cutter Motor when you put back the Cover 3 (6).
(2) Make sure that the step part (7) on the lower side of the Cover 3 (6) is inside of the plate (8). 7
5-80
K105sm5e6_EUA
6. Disconnect the connector (9), and then remove the Grip Ring (10) to remove the Clutch (11 : CL3). Replace the Clutch (11 : CL3) with the new one. 9
10
11 7. Disconnect the connector (12), and then remove the Grip Ring (13) to remove the Clutch (14 : CL4). Replace the Clutch (14 : CL4) with the new one.
12
13 14
8. Disconnect the connector (15), and open the Wire Saddles (16) to release the wires.
16
15 9. Remove 4x6 the screw (17) to remove the Bracket 8 (18), Bush (19) and Clutch (20 : CL5). Replace the Clutch (20 : CL5) with the new one.
17
20 5-81
19
18
K105sm5e6_EUA
5. 4. 3
5-82
K105sm5e6_EUA
NOTE
Make sure that the step part (4) on the lower side of the Cover 7 (3) is inside of the plate (5).
4. Disconnect the connector (6), and then remove the Grip Ring (7) to remove the Clutch (8 : CL6). Replace the Clutch (8 : CL6) with the new one.
5-83
K105sm5e6_EUA
5. Disconnect 2 connectors (9), and remove the 4x6 screw (10). Pull out the Bracket 8 (11) from the shaft. 9 10
11
6. Pull out both the Bush (12) and the Clutch (13 : CL7). Replace the Clutch (13 : CL7) with the new one.
12
12
13
5-84
K105sm5e6_EUA
5. 4. 4
5-85
K105sm5e6_EUA
NOTE
Make sure to insert the hooking part (4) to the slit as the following photo when you put back the Cover 1 (3).
5-86
K105sm5e6_EUA
NOTE
(1) Be careful not to catch the wires of Cutter Motor when you put back the Cover 3 (6).
(2) Make sure that the step part (8) on the lower side of each Cover 3 (6) and Cover 7 (7) is inside of the plate (9).
9 Cover 3s side
9 Cover 7s side
5-87
K105sm5e6_EUA
6. Loosen the 4x6 screw (10) to make the Pulley 3 (11) movable. Also loosen the upper 4x6 screw (12) and remove the lower 4x6 screw (13) to make the Bracket 17 Assembly (14) movable. Remove the Timing Belt 480 (15) and replace it with the new one. 10 12 14
13
11
15
15
NOTE
You do not have to adjust the belt tension. As the Spring 7 (16) gives a proper tension to the Timing Belt 480, tighten the screw (10).
10
16
5-88
K105sm5e6_EUA
5. 4. 5
1. Remove the Cutter Assembly (1) making reference to [5. 4. 1 Replacement of Cutter Assembly] on the page 5-75.
2. Disconnect 5 connectors (2), open 5 Wire Saddles (3), and then put the harness (4) aside. 4 2 2 3
5-89
K105sm5e6_EUA
5. Remove 2 pieces of 4x6 screw (8). Then pull out the Bracket 13 (9).
11
10
5-90
K105sm5e6_EUA
7. Loosen the 4x6 screw (12), slide the Pulley 3 (13) to the arrow mark, and then remove the Timing Belt 480 (14). Replace the Timing Belt 480 (14) with the new one. 12
13 14
NOTE
You do not have to adjust the belt tension. As the Spring Coil 6 (15) gives a proper tension to the Timing Belt 480, tighten the screw (12). 12
15
5-91
K105sm5e6_EUA
5. 4. 6
3. Remove the Timing Belt 330 (4), and replace it with the new one.
5-92
K105sm5e6_EUA
5. 4. 7
5-93
K105sm5e6_EUA
3. Pressing down the Pulley 3 (3), remove the Timing Belt 753 (4). Replace the Timing Belt 753 (4) with the new one.
3 4
NOTE
You do not have to adjust the belt tension. As the Spring 7 (5) gives a proper tension to the Timing Belt 753, tighten the screw (2).
5-94
K105sm5e6_EUA
5. 4. 8
5-95
K105sm5e7_EUA
(Right)
5-96
K105sm5e7_EUA
5. Remove the 4x6 screw (7) to remove the Bracket 5 (8). Also remove 2 pieces of 4x6 screw (9) to remove the Bracket 4 (10).
10 8 6. Disconnect the connectors (11) and remove the 3x12 screws (12) to remove each Sensor (13: PH6 & PH7). Replace each Sensor (13: PH6 & PH7) with the new one. PH6 11
12
11 PH7
12 13
5-97
K105sm5e7_EUA
14
15
8. Disconnect the connectors (16) and remove the 3x12 screws (17) to remove the Sensor (18: PH9). Replace the Sensor (18: PH9) with the new one. 16
17
18
5-98
K105sm5e7_EUA
5. 4. 9
5-99
K105sm5e7_EUA
(Right)
5-100
K105sm5e7_EUA
NOTE
Make sure to insert the hooking part to the slit as the following photo when you put back the Cover 1 (8).
hook
5-101
K105sm5e7_EUA
NOTE
(1) Be careful not to catch the wires of Cutter Motor when you put back Cover 3 (10).
(2) Make sure that the step part (11) on the lower side of each Cover 3 (10) and Cover 7 (4) is inside of the plate (12).
11
11
12 Cover 3 (10)
12 Cover 7 (4)
11 12
5-102
K105sm5e7_EUA
13
14
9. Remove 2 pieces of 4x6 screw (15) to remove the Cover 5 (16). Also remove 2 pieces of 4x6 screw (17) to remove the Cover 8 (18). 16 18
15
17
10. Remove the 4x6 screw (19) to remove each Bracket 12 (20). 19
20 11. Pressing the stoppers (21) inside, remove each Sensor (22: PH8 & PH10). Replace the Sensor (22: PH8 & PH10) with the new one.
22
21
5-103
K105sm5e7_EUA
5-104
K105sm5e7_EUA
5. Disconnect the connectors (5) and remove 4x6 screws (6), and then remove each Dehumidify Heater (7). Replace the Dehumidify Heater (7) with the new one.
5-105
K105sm5e7_EUA
5. 4.11
It is possible to install two Roll Deck Units to the KIP 3000 in maximum. If your KIP 3000 is installed with only one unit, it is possible to add one more unit optionally.
NOTE
After installing the Kit it is necessary to make the KIP 3000 recognize the Roll Deck 2 in the Service Mode, which you can do in the Item Number 058 of the Adjustment Mode. Refer to [8.5.4.29 Recognition of Roll Deck 2 (No.058)] on the page 8-56. 1. Confirm that Roll Deck 2 Kit includes the following parts. 1
10
12
11
8 6
Roll Deck 2 Kit Item Part name 1 Roll Deck 2 Assembly 2 Roll Deck 2 Drive Assembly 3 Spool Assembly 4 Timing Belt 753 5 Timing Belt 480 6 Cover 7
Number of article 1 1 1 1 1 1
Item 7 8 9 10 11 12
Part name Plate 9 Assembly 1 Plate 9 Assembly 2 Bracket 17 Assembly Spring 7 4x6 Tooth Washer Screw 4x6 Bind Screws
5-106
2. Remove both Cover 2 (1) and Cover 3 (2) making reference to [5. 1. 1 Removal of Side Covers] on the page 5-3. Close the Engine Unit.
5-107
K105sm5e8_EUA
5 4 4
5-108
K105sm5e8_EUA
5. Loosen 2 screws (6) and remove 2 screws (7) to remove Bracket 31 (8) and Bracket 32 (9). After removing them, tighten the 2 screws (6). 7
6 8 9
6. Remove the lower screws (10) and loosen the upper screws (11) at both sides.
5-109
K105sm5e8_EUA
7. Rotate both the Brackets 26 (12) in a 180 degrees arc as the arrow mark.
12
NOTE
This is the limited position of Bracket 26 (12). You can not open the Roll Deck so widely in this situation because the Stopper restricts to do so.
Limited position
This is the free position of Bracket 26 (12). You can open the Roll Deck widely in this situation.
Free position
5-110
K105sm5e8_EUA
8. Fix the Brackets 26 (12) at the free position with the screws (10) and (11) you have removed or loosened at the former step 6.
10 11
10 11
NOTE
Please note that the position of the screws (10) varies if you change from limited position to free position.
5-111
K105sm5e8_EUA
9. Mount the Roll Deck 2 Assembly (13) onto the Rails (14). 13 14
13
10. Fix the Roll Deck 2 Assembly to both Rails with 2 pieces of 4x6 Tooth Washer Screw (15).
15 15
5-112
K105sm5e8_EUA
11. Loosen 4 pieces of 4x6 screw (16), and then remove the Cover 1 (17).
16
17
12. Remove 5 pieces of 4x6 screw (18), and then remove the Cover 3 (19).
18 18
19
13. Joint both the Roll Deck 1 Assembly and Roll Deck 2 Assembly with 2 pieces of 4x6 screw (20).
20 20
5-113
K105sm5e8_EUA
14. Mount the Roll Deck 2 Drive Assembly (21) onto the Roll Deck.
21
21
21
15. Fix the Roll Deck 2 Drive Assembly (21) with 2 pieces of 4x6 screw (22),
22
22
16. Attach the Bracket 17 Assembly (23) with 2 pieces of 4x6 screw (24). 24
23 23 24
5-114
K105sm5e8_EUA
17. Attach the Plate 9 Assembly 1 (25) with one piece of 4x6 Bind Screw (26). Then hook the Spring 7 (27). 27
25
26
25
27
NOTE
(1) Do not tighten the screw (26) at this time because the Plate 9 Assembly 1 (25) must be movable when you stretch the Belt in the next step. (2) Plate 9 Assembly 1 and Plate 9 Assembly 2 look similar, but you can distinguish between them because the Plate 9 Assembly 1 has a longer shaft than Plate 9 Assembly 2. Plate 9 Assembly 1 (Longer shaft) Plate 9 Assembly 2 (Shorter shaft)
5-115
K105sm5e8_EUA
18. Stretch the Timing Belt 480 (28) between gears. Then, tighten the 4x6 screw (26) to fix the Plate 9 Assembly 1. 28
26
28
NOTE
(1) If it is hard to stretch the Timing Belt 480 (28), loosen the upper one of screw (24) and remove the lower one (24) to make the Bracket 17 Assembly (23) movable. You will be able to stretch the belt if you do so. 24 23
24
(2) You do not have to adjust the belt tension especially. As the Spring 7 (27) gives enough tension to the Timing Belt 480, just tighten the screw (26). 26
27
5-116
K105sm5e8_EUA
19. Attach the Plate 9 Assembly 2 (29) with the 4x6 screw (30). Then hook another piece of Spring 7 (31). 31
29
31
30
29
NOTE
(1) Do not tighten the screw (30) at this time because the Plate 9 Assembly 2 (29) must be movable when you stretch the Belt in the next step. (2) Plate 9 Assembly 1 and Plate 9 Assembly 2 look similar, but you can distinguish between them because the Plate 9 Assembly 1 has a longer shaft than Plate 9 Assembly 2. Plate 9 Assembly 1 (Longer shaft) Plate 9 Assembly 2 (Shorter shaft)
5-117
K105sm5e8_EUA
20. Stretch the Timing Belt 753 (32) among gears and pulleys. Then, tighten the screw (30) to fix the Plate 9 Assembly 2. 32
30
32
NOTE
You do not have to adjust the belt tension especially. As the Spring 7 (31) gives enough tension to the Timing Belt 753, just tighten the screw (30). 30 31
19
5-118
K105sm5e8_EUA
(Right)
5-119
K105sm5e8_EUA
23. Attach the Cover 7 (33) with 4 pieces of 4x6 screw (34). 33 34
34
33
NOTE
Make sure that the step part (35) on the lower side of the Cover 7 (33) is inside of the plate (36).
35
36
24. Set the Roll Spool (37) to the Roll Deck Unit finally. 37
5-120
K105sm5e8_EUA
5. 4.12
NOTE
3 screws (3) and Cover 7 (4) are not reused any longer.
5-120
K105sm5e9_EUA
(Right)
5-121
K105sm5e9_EUA
NOTE
Hooks (9) at both sides of the Cover 1 (8) holds the plate firmly. To release the hooks, bring up the Cover 1 (8) and move it frontward.
5-122
K105sm5e9_EUA
7. Remove 5 pieces of 4x6 Bind Screw (10), and remove the Cover 3 (11). 10 10
10
11
NOTE
The Cover 3 (11) firmly holds the clutch stoppers (12). Move the top plate (13) of the Cover 3 as the arrows to release from the clutch stoppers, and the Cover 3 can be removed easily.
13 Released
12
5-123
K105sm5e9_EUA
14
9. Loosen the 4x6 Bind Screw (15) to unfasten the Belt 60S3M480 (16). Remove the Belt 60S3M480 (16).
15
16
NOTE
Belt 60S3M480 (16) is not reused any longer.
5-124
K105sm5e9_EUA
10. Remove the 4x6 Bind Screw (15), Washer (17), Spring 7 (18) and Plate 9 Assembly 1 (19). 18 15 19
17
NOTE
4x6 Bind Screw (15), Washer (17), Spring 7 (18) and Plate 9 Assembly 1 (19) are not reused any longer.
11. Remove 2 pieces of 4x6 Bind Screw (20), and remove the Bracket 17 Assembly (21).
20 21
20
NOTE
4x6 Bind Screw (20) and Bracket 17 Assembly (21) are not reused any longer.
5-125
K105sm5e9_EUA
12. Loosen the 4x6 Bind Screw (22) to unfasten the Belt 40S3M753 (23). Remove the Belt 40S3M753 (23).
22
23
NOTE
Belt 40S3M753 (23) is not reused any longer.
13. Remove 4x6 Bind Screw (22), Washer (24), Spring 7 (25) and Plate 9 Assembly 2 (26). 25
24
22
26
NOTE
4x6 Bind Screw (22), Washer (24), Spring 7 (25) and Plate 9 Assembly 2 (26) are not reused any longer.
5-126
K105sm5e9_EUA
27
27
28
28
NOTE
Roll Deck 2 Drive Assembly (28) is not be reused any longer.
29
29
5-127
K105sm5e9_EUA
11
NOTE
(1) Place the step part (30) on the bottom of the Cover 3 (4) inside of the rail plate (31).
(2) Do not break the Cutter Motor wire (32) by catching between plates.
32
(3) Fit the clutch stoppers (12) into the notches on the Cover (11).
12
5-128
K105sm5e9_EUA
NOTE
Fit the hooks at both sides of the Cover 1 (8) into the notches as follows.
33
33
5-129
K105sm5e9_EUA
21. Move the whole Roll Deck to the arrow direction a little, so that the Lock Shaft Receivers (35) should be nearer to the exit side than Bracket 26 (36).
36
35
37
5-130
K105sm5e9_EUA
38
38
39
39
25. Remove 5 pieces of 4x6 screw (40) at both sides. (2 pieces on the right and 3 pieces on the left)
40 40
5-131
K105sm5e9_EUA
41
42
28. Loosen the upper 4x6 screws (43) and remove the lower 4x6 screws (44) at both sides.
44 : Remove
44 : Remove
43 : Loosen
43 : Loosen
5-132
K105sm5e9_EUA
29. Rotate both the Brackets 26 (36) in a 180 degrees arc as the arrow mark.
36
NOTE
This is the limited position of Bracket 26 (36). The stopper restricts to open the Roll Deck widely with this state, because it is not required to do so when the Roll Paper Deck 2 is not installed.
Limited position
This is the free position of Bracket 26 (36). The Roll Deck can be opened widely to access to the Roll Paper Deck 2 with this state.
Free position
5-133
K105sm5e9_EUA
30. Fix the Brackets 26 (13) at the limited position with the 4x6 screws (43) and (44) you have removed or loosened at the former step 26.
43 44
43 44
NOTE
Note that the position of 4x6 screws (44) varies if you change from limited position to free position. 31. Replace both the Cover 2 (41) and Cover 3 (42), and close the Engine Unit.
41
42
5-134
K105sm5e9_EUA
43
43
33. Hook Bracket 31 (44) and Bracket 32 (45) on the screws (43). Tighten the screws (43) and fix both brackets with 1 screw each (29). Bracket 31 (P/N: Z081300020) Bracket 32 (P/N: Z081300030)
44
45
44 29 29
45
43
43
5-135
K105sm5e9_EUA
5 4 4
5-136
K105sm5e9_EUA
46
37. Press and hold the [MENU] Key on the Sub UI, and turn on the machine. (The key operation of Sub UI is unlocked.) 38. Press and hold the [ * ] key, and press the keys in the order as [ ], [ enter the Service Mode. All segments on the LCD light right after entering the Service Mode. ], [ ] and [ ] to
39. Keep your finger away from the [ * ] key. The ROM version is indicated. ROM version is indicated.
RO M Ver . 1. 6
FPG Ver . 0. 3 A
40. Press the [MENU] Key 4 times to indicate (4) Adjust Mode on the LCD.
RO M Ver . 1. 6
FPG Ver . 0. 3 A
[MENU]
( 4) A d j us t
Mode
41. Press the [ENTER] Key to enter the Adjustment Mode. (The LCD indicates as follows right after entering the Adjustment Mode.)
( 4) A d j us t Mode
[ENTER]
No000 020
[ 020 ]
L ead Reg. ( Ro l l )
42. Indicate the item number 058 (Deck 2 Option) pressing the [
No 0 0 0 0 2 0 [ 020 ]
] and [
0 01
] keys.
[ 001 ]
L e a d Re g . ( Ro l l )
] and [
No 0 5 8
De c k 2 Op t i o n
5-137
K105sm5e9_EUA
43. Press the [ENTER] Key. The setting value in the parenthesises flashes. It is changeable when flashing.
No 0 5 8 0 01 [ 001 ]
De c k 2 Op t i o n
[ENTER]
No 0 5 8
0 01
[ 001 ]
De c k 2 Op t i o n
NOTE
Another value that is not in the parenthesises is the current setting value.
No 0 5 8 0 01 [ 001 ] De c k 2 Op t i o n
Current setting value 44. Change the setting value to 000 (Roll 2 is not installed) pressing the [
No 0 5 8 0 01 [ 001 ]
] and [
[ 000 ]
] keys.
De c k 2 Op t i o n
] and [
No 0 5 8
0 01
De c k 2 Op t i o n
45. Press the [ENTER] Key to validate the new setting. The setting value stops flashing when validated. [ENTER]
No 0 5 8
0 01
[ 000 ]
No 0 5 8
0 00
[ 000 ]
De c k 2 Op t i o n
De c k 2 Op t i o n
46. Press both [MENU] Key and [ * ] Key at the same time to cancel the Service Mode. The information of the paper on Roll 2 (R2:) will not be indicated any longer.
No 0 5 8 0 00 [ 000 ]
De c k 2 Op t i o n
[MENU] and [ * ]
P r i n t e r Re a d y R1 :
47. Replace the Cover (46). Finally turn off the machine to lock the key operation of Sub UI.
46
5-138
K105sm5e9_EUA
5. 5
5. 5. 1
Photoconductive Drum
Replacement of the Photoconductive Drum
5-139
K105sm5eA_EUA
4. Remove 5 pieces of 4x6 screw (4) at both sides. (2 pieces on the right and 3 pieces on the left)
4 4
5-140
K105sm5eA_EUA
9. Disconnect the connector (10), and open the Wire Saddle (11) to release the harness.
10 11
12 5-141
K105sm5eA_EUA
11. Remove 4 pieces of 4x6 screw (13) and 2 pieces of washer screw (14).
13
14
13
13
14
13
15
13. There are 2 pieces of Stopper (16) at both sides, which lock the LED Head Frame. Loosen the screw (17) and then slide the Stoppers (16) outside to unlock the LED Head Frame.
16
17
Unlock position
K105sm5eA_EUA
NOTE
The Stopper 2 (19) comes out automatically to prevent the LED Head Frame from falling down.
19
Press the Stopper 2 as the right photo if you will close the LED Head Frame.
20
5-143
K105sm5eA_EUA
16. Remove the 4x6 screw (21), and remove the Plate (22) and Pulley Gear (23).
23
21
23
22
NOTE
The Belt 4 (24) is automatically loosed if you open the Engine Unit. It will be strained if you close the Engine Unit.
24
5-144
K105sm5eA_EUA
17. Remove the Collar (25) from the left Drum Shaft. 25
NOTE
The new (spare) Drum Assembly does not include the Collar (25). So please reuse it.
18. There are 2 pieces of screw (26) on the left which fix the Block (27). Loosen these screws and rotate the Block (27) as the arrow marks. 26
26
27
5-145
K105sm5eA_EUA
19. Similarly loosen 2 pieces of screw (28) on the right and rotate the Block 2 (29) as the arrow marks. 28
28
29
20. Remove the Photoconductive Drum (30), and replace it with the new one. 30
NOTE
The Aluminium Block (27) and (29) maintain the focus of the LED Head. Therefore it is necessary to re-position them correctly after replacing the Photoconductive Drum. Please fix them making reference to [5.5.2 How to fix the Aluminium Blocks] on the page 5-147.
5-146
K105sm5eA_EUA
5. 5. 2
There are Aluminium Blocks at both sides of the Drum Shaft. As they maintain the focus of LED Head, it is necessary to re-position them correctly after replacing the Photoconductive Drum.
Aluminium Blocks Print out the Test Pattern No.3 to check if the Aluminium Blocks are fixed at the correct position. The density of halftone is uniform as the following left image if the Aluminium Blocks are fixed at the correct positions (focus is good). But the density of halftone is different among image blocks as the following right image if blocks are not fixed correctly (focus is not good). Good (Gray looks uniform) No good (Gray looks not uniform)
If the focus of LED Head is not good, fix the Aluminium Blocks properly making reference to the next page.
5-147
K105sm5eA_EUA
There are Aluminium Blocks (1) at both sides, and each of them is fixed with 2 screws (2). Left side Right side
2 2 2
Do as follows to fix the Aluminium Blocks correctly. a) Always fix the Aluminium Block of the left side first, and then that of the right side. b) When you tighten 2 screws (2) to fix each Aluminium Block, always tighten the upper one first, and then the lower one. The following picture shows the order to tighten the screws. Tighten in the order as A, B, C and D necessarily. A C
Drum
D Right side
NOTE
The focus of LED Head will become defective if you do not satisfy the above requirements. Go to the next page as the above method is shown.
5-148
K105sm5eA_EUA
1. Rotate the Left Aluminium Block (3) fully to the arrow direction (A) and also press it down as the arrow (B), and then tighten the upper screws (4) firstly and then the lower one (5) secondary. Left side
A 3 B 4
A B 3
NOTE
There should be no space between the Bearing and U-shape notch. The LED focus will become defective if there is any space. Correct Incorrect
Space
5-149
K105sm5eA_EUA
2. Similarly rotate the Right Aluminium Block (6) fully to the arrow direction (C) and also press it down as the arrow (D), and then tighten the upper screws (7) firstly and then the lower one (8) secondary. C D D 8 7 6
C 6
3. Print out the Test Pattern No.3, and confirm that the density of halftone is uniform. If it is still not uniform, fix the Aluminium Blocks again. Good (Gray looks uniform) No good (Gray looks not uniform)
5-150
K105sm5eA_EUA
5. 5. 3
1. Remove the Photoconductive Drum from the machine making reference to [5. 5. 1 Replacement of the Photoconductive Drum] on the page 5-139.
2. Wipe the surface of Photoconductive Drum with a dry cloth. 3. If the toner strongly sticks on the surface and it is impossible to remove it, wipe with the cloth impregnated with the alcohol. 4. After using the alcohol, wipe all surface of Drum with a cloth impregnated with water so that there should be no unevenness of cleaning. 5. Wipe all surface of Drum with a dry cloth, and dry the Drum leaving in a dark place for about 10 minutes. 6. Put back the Drum to the machine.
NOTE
(1) A defective image may be printed right after the cleaning (about 10 to 20 sheets of A0), but it will be fixed naturally as the time passes. (2) Wipe the surface always to one direction. You will damage the Drum if you wipe in other ways.
Good
No good
No good
No good
5-151
K105sm5eA_EUA
5. 5. 4
Replacement of Belt 4
2 2
5-152
K105sm5eA_EUA
NOTE
Belt 4 is automatically unfastened if only you open the Engine Unit.
5-153
K105sm5eA_EUA
5. 6
5. 6. 1
LED Head
Replacement of the LED Head Unit
5-154
K105sm5eB_EUA
4. Remove 5 pieces of 4x6 screw (4) at both sides. (2 pieces on the right and 3 pieces on the left)
4 4
5-155
K105sm5eB_EUA
9. Disconnect the connector (10), and open the Wire Saddle (11) to release the harness.
10 11
12 5-156
K105sm5eB_EUA
11. Remove 4 pieces of 4x6 screw (13) and 2 pieces of washer screw (14).
13
14
13
13
14
13
15
13. There are 2 pieces of Stopper (16) at both sides, which lock the LED Head Frame. Loosen the screw (17) and then slide the Stoppers (16) outside to unlock the LED Head Frame.
16
17
Unlock position
K105sm5eB_EUA
NOTE
The Stopper 2 (19) comes out automatically to prevent the LED Head Frame from falling down.
19
Press the Stopper 2 as the right photo if you will close the LED Head Frame.
5-158
K105sm5eB_EUA
15. Remove the 4x6 screw (20) to remove the Fixing Bracket (21) on the right.
21
20
21
NOTE
You do not have to put back the Fixing Bracket (21) at the time of reassembly, because it is a part required only before the delivery of machine.
16. Loosen 2 pieces of 4x10 screw (22) to make the Plate (23) enough movable.
23
22
5-159
K105sm5eB_EUA
17. Move the Plate (23) to the right to release the pin (24) of Corona Block. Then remove the Image Corona Unit (25). 25
23
25
24
25
5-160
K105sm5eB_EUA
27
28
20. Move the right end of LED Head Unit (29) a little to the front side, and then slide the whole unit to the right. Replace the LED Head Unit (29) with the new one. 29 29
NOTE
It is necessary to check and adjust the focus of LED Head after its replacement. Refer to [5. 6. 2 LED focus adjustment] on the page 5-162.
5-161
K105sm5eB_EUA
5. 6. 2
Please adjust the focus of LED Head after the replacement of LED Head. Also adjust it if you have lost the correct focus by some reason. Adjust the focus by the following 3 steps. (1) Check of the Test Pattern Image (2) Positioning of the Aluminium Blocks (3) Focus Adjustment with Spacers
5. 6. 2. 1
Print out the Test Pattern No.3 in the Service Mode, and check its halftone image. If the density of halftone is uniform as the following left image, you do not have to make anything because the focus is correctly adjusted. But it is different among image blocks as the following right image, it is necessary to adjust the focus. Go to [5. 6. 2. 2 Positioning of the Aluminium Blocks] on the next page in this case. Good No good (Adjustment is required.)
5-162
K105sm5eB_EUA
5. 6. 2. 2
There are Aluminium Blocks at both sides of the Drum Shaft, which adjust the distance between LED Head and Drum. If the LED focus is not correct, at first it is necessary to place them at the correct positions in the following way.
Aluminium Blocks 1. Pull up the Lever 2 (1) to open the Engine Unit.
5-163
K105sm5eB_EUA
4. Remove 5 pieces of 4x6 screw (4) at both sides. (2 pieces on the right and 3 pieces on the left)
4 4
5-164
K105sm5eB_EUA
9. Disconnect the connector (10), and open the Wire Saddle (11) to release the harness.
10 11
12 5-165
K105sm5eB_EUA
11. Remove 4 pieces of 4x6 screw (13) and 2 pieces of washer screw (14).
13
14
13
13
14
13
15
13. There are 2 pieces of Stopper (16) at both sides, which lock the LED Head Frame. Loosen the screw (17) and then slide the Stoppers (16) outside to unlock the LED Head Frame.
16
17
Unlock position
K105sm5eB_EUA
NOTE
The Stopper 2 (19) comes out automatically to prevent the LED Head Frame from falling down.
19
Press the Stopper 2 as the right photo if you will close the LED Head Frame.
20
5-167
K105sm5eB_EUA
16. Remove the 4x6 screw (21), and remove the Plate (22) and Pulley Gear (23).
23
21
23
22
NOTE
The Belt 4 (24) is automatically loosed if you open the Engine Unit. It will be strained if you close the Engine Unit.
24
5-168
K105sm5eB_EUA
17. There are Aluminium Blocks (25) at both sides, and each of them is fixed with 2 screws (26). Left side Right side
25
25
26 26 26
26
Do as follows to fix the Aluminium Blocks correctly. a) Always fix the Aluminium Block of the left side first, and then that of the right side. b) When you tighten 2 screws (26) to fix each Aluminium Block, always tighten the upper one first, and then the lower one. The following picture shows the order to tighten the screws. Tighten in the order as A, B, C and D necessarily. A C
Drum
D Right side
NOTE
The focus of LED Head will become defective if you do not satisfy the above requirements. Go to the next page as the above method is shown.
5-169
K105sm5eB_EUA
17-1. Rotate the Left Aluminium Block (27) fully to the arrow direction (A) and also press it down as the arrow (B), and then tighten the upper screws (28) firstly and then the lower one (29) secondary. Left side
A 27 B 28
A B 27
29
NOTE
There should be no space between the Bearing and U-shape notch. The LED focus will become defective if there is any space. Correct Incorrect
Space
5-170
K105sm5eB_EUA
17-2. Similarly rotate the Right Aluminium Block (30) fully to the arrow direction (C) and also press it down as the arrow (D), and then tighten the upper screws (31) firstly and then the lower one (32) secondary. C 30 D 32 D 31
C 30
18. Reassemble the machine in the reversed order. 19. Print out the Test Pattern No.3, and confirm that the density of halftone is uniform. Good (Gray looks uniform) No good (Gray looks not uniform)
If it is still not uniform although you have fixed the Aluminium Blocks correctly, it is necessary to make focus adjustment with Spacers. Go to [5. 6. 2. 3 Focus Adjustment with Spacers] on the next page in this case.
5-171
K105sm5eB_EUA
5. 6. 2. 3
There may be the case that the focus of LED is not correct even if you have placed the Aluminium Blocks at both sides of the Drum Shaft correctly. This is because the height of the LED is mechanically different between left and right by some reason. In this case adjust the height by adding or removing the Spacers. 1. Remove the Guides 3 (1). 1
2 2
3. Disconnect the connector (4), and open the Wire Saddles (5) to release the harness. 5
5-172
K105sm5eB_EUA
5. Remove 4 pieces of 4x6 screw (7) and 2 pieces of washer screw (8).
5-173
K105sm5eB_EUA
7. There are 2 pieces of Stopper (10) at both sides, which lock the LED Head Frame. Loosen the screw (11) and then slide the Stoppers (10) outside to unlock the LED Head Frame.
10
11
Lock position
Unlock position
5-174
K105sm5eB_EUA
12
NOTE
The Stopper 2 (13) comes out automatically to prevent the LED Head Frame from falling down.
13
Press the Stopper 2 as the right photo if you will close the LED Head Frame.
5-175
K105sm5eB_EUA
9. There are Spacers (14) on each Aluminium Block at both sides. The height of the LED Head can be adjusted by adding more Spacer or removing some of them. Remove the screw (15), and remove all Spacers (14) at first. And then adjust the height of LED Head adding or removing the Spacers (14). 14 15 14
14
NOTE
(1) The number of Spacers initially installed is individually different machine to machine. (2) There are 3 kinds of spacers such as 0.1mm, 0.08mm and 0.05mm in thickness. Please find the best combination by making several times of trial. (3) Basically thinner Spacers (0.08mm & 0.05mm ones) must be held between the 0.1mm Spacer as the right picture. 0.1mm 0.08mm & 0.05mm
5-176
K105sm5eB_EUA
NOTE
(4) It is quite not clear which of addition or removal of Spacer is effective to solve the focus problem. (Even if the defective image caused by the focus problem looks same, for example, it is fixed by addition in some case but in another case it is fixed by removal. Only the way to find the best focus is just trial. Please try both removal and addition to find which way the image becomes better. After finding the better way, try several combinations of Spacers to find the best height. Removal of Spacer (Worse result) Addition of Spacer (Better result)
5-177
K105sm5eB_EUA
5. 7
5. 7. 1
Image Corona
Removal of the Image Corona Unit
5-178
K105sm5eC_EUA
4. Remove 5 pieces of 4x6 screw (4) at both sides. (2 pieces on the right and 3 pieces on the left)
4 4
5-179
K105sm5eC_EUA
9. Disconnect the connector (10), and open the Wire Saddle (11) to release the harness.
10 11
12 5-180
K105sm5eC_EUA
11. Remove 4 pieces of 4x6 screw (13) and 2 pieces of washer screw (14).
13
14
13
13
14
13
15
13. There are 2 pieces of Stopper (16) at both sides, which lock the LED Head Frame. Loosen the screw (17) and then slide the Stoppers (16) outside to unlock the LED Head Frame.
16
17
Unlock position
K105sm5eC_EUA
NOTE
The Stopper 2 (19) comes out automatically to prevent the LED Head Frame from falling down.
19
Press the Stopper 2 as the right photo if you will close the LED Head Frame.
5-182
K105sm5eC_EUA
15. Remove the 4x6 screw (20) to remove the Fixing Bracket (21) on the right.
21
20
21
NOTE
You do not have to put back the Fixing Bracket (21) at the time of reassembly, because it is a part required only before the delivery of machine.
16. Loosen 2 pieces of 4x10 screw (22) to make the Plate (23) enough movable.
23
22
5-183
K105sm5eC_EUA
17. Move the Plate (23) to the right to release the pin (24) of Corona Block. Move the right end of Image Corona (25) a little to the front side, and then slide the whole unit to the right. 25
23
25
24
25
5-184
K105sm5eC_EUA
5. 7. 2
1. Remove the Image Corona Unit (1) from the machine making reference to [5. 7. 1 Removal of the Image Corona Unit] on the page 5-178. 1
2. Loosen the Set Screw (2) with hexagon wrench. The Block 3 (3) moves to the arrow mark and the Grid Plate is unfastened.
5-185
K105sm5eC_EUA
NOTE
Check the following when reassembling. (1) The side edge of Block 3 (3) should stop at 0.5mm short of the side face (4) of the corona block for a proper tension. Rotate a hexagon wrench in either direction with pressing down Grid Plate (5). 0.5mm 0.5mm press down
4 5 5 3 3 4
(2) Carry Image Corona Unit (1) by both corona blocks so that Grid Plate (5) faces the floor. Make sure that Grid Plate (5) has no excess slack (in less than 1mm) on the middle of the housing.
1 1 5
5-186
K105sm5eC_EUA
NOTE
If Grid Plate is dirty, wash it with the neutral detergent and then with water. Dry it well after washing. 4. Loosen 3 pieces of 3x6 screw (6), and then remove Corona Housing (7) and Plate Electrode (8).
5-187
K105sm5eC_EUA
5. Remove the Flush Head Screw (9), and remove each Cover (10) and Cover 2 (11).
10 11
6. Loosen the screws (12) to lower the Height Adjuster. (It becomes easy to remove the Corona Wire as it is unfastened by this treatment.)
12
12
5-188
K105sm5eC_EUA
7. Remove the Spring (13), and remove the Corona Wire (14). Replace the Corona Wire (14) with the new one. 14
13
NOTE
(1) Please keep 11mm between Corona Wire (14) and bottom plate of the Corona Unit after the replacement.
11mm
(2) Fit the Corona Wire into the groove of Height Adjuster (15). Also fit the beads (16) into the correct positions.
15
16
5-189
K105sm5eC_EUA
5. 8
5. 8. 1
2. Holding both Corona Blocks (2), remove the Transfer / Separation Corona (3) from the machine.
5-190
K105sm5eD_EUA
NOTE
There is the Drum above the Transfer / Separation Corona. Do not touch it.
5-191
K105sm5eD_EUA
5. 8. 2
1. Remove the Transfer / Separation Corona (1) making reference to [5. 8. 1 Removal of the Transfer / Separation Corona] on the page 5-190.
2. There are 5 pieces of Corona Guards A (2) and Corona Guards B (3) on the housing. Remove them pressing the stoppers (4) with such tool as a screwdriver. 4 2 3
NOTE
Do not replace the position of Corona Guards A (2) and Corona Guards B (3) at the time of reassembly.
5-192
K105sm5eD_EUA
5-193
K105sm5eD_EUA
4. Remove the Wire Springs (7), and remove the Corona Wires (8). Replace the Corona Wires (8) with the new ones. 7 7
NOTE
(1) Keep a specified distance between each Corona Wire and bottom plate of the housing. There are 2 types of Tr/St Corona Assy, they differs from the position and the number of plastic sheets on the housing. A specified distance depends on the Assy type. 1 sheet type
Transfer Separation
2 sheets type
Transfer Separation
10mm
11mm
11mm
11mm
To adjust the distance, rotate the screws (9) with a flathead screwdriver.
(2) Fit the Corona Wire into the groove of Height Adjuster (10). Also fit the beads (11) into the correct positions. 10 11
5-194
K105sm5eD_EUA
5. 9
5. 9. 1
Engine Frame
Replacement of DC Motor (M4) and Developer Press Sensor (PH4)
2. Remove the 4x6 screws and washers (2) at both sides to make the Bands (3) free.
2 3
2 3
5-195
K105sm5eD_EUA
3. There are Pins (4) at both sides. Slide them inside to remove the Cover 4 (1).
5-196
K105sm5eD_EUA
6. Close the Bypass Feeder, and then open the Developer Press Unit (7).
7. Disconnect the connector (8) and remove 3 pieces of screw (9), and remove the DC Motor (10). Replace the DC Motor (10) with the new one. 8
10
5-197
K105sm5eD_EUA
8. Remove the 4x6 screw (11), release the harness from the Edge Saddle (12), and disconnect the connector (13). 12
11
13
9. Pressing the stoppers (14) with such tool as a screwdriver, remove the Developer Press Sensor (15). Replace the Developer Press Sensor (15) with the new one.
5-198
K105sm5eD_EUA
5. 9. 2
1. Remove the Developer Unit (1) from the machine making reference to [5. 2. 1 Removal of the Developer Unit] on the page 5-8.
2. Remove 2 pieces of 3x6 screw (2), and then turn over the Bracket 11 (3).
5-199
K105sm5eD_EUA
3. Remove the screw (4) and disconnect the connector (5) to remove each Sensor (6 : Manual Set Sensor or Registration Sensor). Replace the Sensor (15) with the new one. 6 4
5-200
K105sm5eD_EUA
5. 9. 3
1. Remove the Fuser Unit (1) from the machine making reference to [5. 3. 1 Removal of the Fuser Unit] on the page 5-44.
2. Disconnect the connector (2), remove 2 pieces of screw (3), and remove each Fan (4 : BL5 & BL6). Replace the Fan (4 : BL5 & BL6) with the new one. 3
5-201
K105sm5eD_EUA
5. 9. 4
3. Moving the stopper levers (4) to the inside, remove each Duct 5 (5) with Filter 2.
5 5-202
K105sm5eD_EUA
4. Remove 2 pieces of 4x6 screw (6), and then slide the Duct 6 (7) to the left. 7
6. Remove the Blower (9 : BL3 & BL4) moving as the following photos. 9
5-203
K105sm5eD_EUA
5-204
K105sm5eD_EUA
3. Disconnect the connector on the left (3), and then remove the Inner Transport Unit (4).
5-205
K105sm5eD_EUA
5.10. 2
1. Remove the Inner Transport Unit (1) from the machine making reference to [5.10. 1 Removal of the Inner Transport Unit] on the page 5-204.
2. There are Shafts (2) under the Belt (3). Remove these Shafts (2).
5-206
K105sm5eD_EUA
6. Remove 2 pieces of 3x6 screw (7) and disconnect the connector (8) to remove the Exit Sensor Assembly (9). 8
5-207
K105sm5eD_EUA
7. Pressing the Stoppers (10) inward, remove the Sensor (11) from the Sensor Bracket. Replace the Sensor (11) with the new one.
10
11
12
12
5-208
K105sm5eD_EUA
9. Remove the Rollers (13), and remove the Belts (14). Replace the Belts (14) with the new ones.
13
14
NOTE
Be careful of the outside/inside of the Belt (14). The smooth and shiny side of it should be inside.
Outside
Inside
5-209
K105sm5eD_EUA
1. Remove 4 pieces of 4x6 screw (1), loosen 4 pieces of 4x6 screw (2), and then remove the Cover 15 (3). 1
5-210
K105sm5eE_EUA
6 6
5-211
K105sm5eE_EUA
6. Loosen the 4x6 screw (8), move the Pulley 3 (9) toward the arrow mark, and then remove the Belt 1 (10). Replace the Belt 1 (10) with the new one.
10
NOTE
To adjust the tension of the Belt 1, do as follows. If you do not make the following works, the Belt 1 may slip because the tension is not correct. a) Giving the spring tension to the Belt 1, tighten the screw of each Pulley 3. b) Turn on the machine, and then turn it off some seconds later. The Belt 1 is driven by the motor, and it may be slackened around the Pulley 3 at this time. c) Loosen the screw to release the Pulley 3. The slack of Belt 1 generated by the above b) is removed because the Tension Spring pulls the Pulley 3. Then tighten the screw again.
5-212
K105sm5eE_EUA
7. Loosen the 4x6 screw (11), move the Pulley 3 (12) toward the arrow mark, and then remove the Belt 3 (13). Replace the Belt 3 (13) with the new one.
11
13
12
NOTE
To adjust the tension of the Belt 3, do as follows. If you do not make the following works, the Belt 3 may slip because the tension is not correct. a) Giving the spring tension to the Belt 3, tighten the screw of each Pulley 3. b) Turn on the machine, and then turn it off some seconds later. The Belt 3 is driven by the motor, and it may be slackened around the Pulley 3 at this time. c) Loosen the screw to release the Pulley 3. The slack of Belt 3 generated by the above b) is removed because the Tension Spring pulls the Pulley 3. Then tighten the screw again. 5-213
K105sm5eE_EUA
8. Remove 2 pieces of each Retaining Ring-E (E7) and Bush (14), remove the 4x6 screw (15), and then remove the Plate 7 (16). 14
15
16
5-214
K105sm5eE_EUA
9. Loosen the 4x6 screw (17), move the Pulley 3 (18) toward the arrow mark, and then remove one more piece of Belt 1 (19). Replace the Belt 1 (19) with the new one.
19
18
17
NOTE
To adjust the tension of the Belt 1, do as follows. If you do not make the following works, the Belt 1 may slip because the tension is not correct. a) Giving the spring tension to the Belt 1, tighten the screw of each Pulley 3. b) Turn on the machine, and then turn it off some seconds later. The Belt 1 is driven by the motor, and it may be slackened around the Pulley 3 at this time. c) Loosen the screw to release the Pulley 3. The slack of Belt 1 generated by the above b) is removed because the Tension Spring pulls the Pulley 3. Then tighten the screw again. 5-215
K105sm5eE_EUA
10. Remove 6 pieces of 4x10 screw (20) to remove the Plate 6 Assembly (21). 20
20
21
5-216
K105sm5eE_EUA
11. Remove the Set Screws (22) to remove each Pulley 5 (23) and Pulley 4 (24). 24 23
22
NOTE
Keep 8.9mm between the bracket and each Pulley 5 (21) and Pulley 4 (22) at the time of reassembly.
8.9mm
8.9mm
12. Remove 4 pieces of 4x10 screws (25) to remove each DC Motor (26 : Main) (27 : Fuser). Replace each DC Motor (26 & 27) with the new one. 25 25 27 26
25
25
5-217
K105sm5eE_EUA
5.11. 2
5-218
K105sm5eE_EUA
4. Loosen the 4x6 screw (4), move the Pulley 3 (5) toward the arrow mark, and then remove the Belt 1 (6). Replace the Belt 1 (6) with the new one.
5-219
K105sm5eE_EUA
5. Remove 2 places each Retaining Ring-E (E7) and Bush (7), remove the 4x6 screws (8), and then remove the Plate 8 (9). 7
6. Remove the Hex. Cap Screw (10) to remove the Pulley 13 (11).
11
10
7. Disconnect the connector (12), and remove the 4x6 screw (13) to remove both the Clutch (14) and the Bracket Clutch (15). Replace the Clutch (14) with the new one. 12
11
13
14
5-220
K105sm5eE_EUA
5.11. 3
1. Remove 4 pieces of 4x6 screw (1), loosen 4 pieces of 4x6 screw (2), and then remove the Cover 15 (3). 1
2. Disconnect the connector (4), remove the 4x6 screw (5), and then remove the Bracket Blower (6). 5
4 6
3. Remove 3 pieces of 4x35 screw (8) to remove the Blower (9). Replace the Blower (9) with the new one.
5-221
K105sm5eE_EUA
5.12
5.12. 1
Scanner Unit
Removal of the Scanner Unit
1
2. Remove 8 pieces of 4x6 screw (2) on both front side and back side of machine. 2 2
5-222
K105sm5eF_EUA
5-223
K105sm5eF_EUA
9 9
5-224
K105sm5eF_EUA
10
11
11. Remove 4 pieces of 4x6 screw (12) to remove the Bracket Right (13) on the right. 12
12
13
12. Remove 4 pieces of screw (14) to remove the Bracket Left (15) on the left. 14
15
14
5-225
K105sm5eF_EUA
13. Loosen 4 pieces of 4x6 screw (16), remove 4 pieces of 4x6 screw (17), and then remove the Cover 15 (18).
17
18 16
14. Disconnect the USB Cable (19) from the PC, which runs from the Scanner Unit. 19
15. Open the Wire Saddles (20) to release the USB Cable (19).
20
20
19
16. Disconnect the connector (21), and open the Wire Saddles (22) to release the USB Cable and the DC harness.
22
21
5-226
K105sm5eF_EUA
CAUTION
Make sure to close the Engine Unit before removing the screws which fix the Scanner Unit. Otherwise the Scanner Unit may drop and break.
18. Remove 4 pieces of 4x6 screw (23) which fix the Scanner Unit. (Right side)
23 (Left side)
23
5-227
K105sm5eF_EUA
CAUTION
Please bring the Scanner Unit by 2 persons as it is heavy.
5-228
K105sm5eF_EUA
5.12. 2
Replacement of Motor
1. Remove the Scanner Unit (1) from the machine making reference to [5.12. 1 Removal of the Scanner Unit] on the page 5-222.
2. Pull up the Levers (2) and open the Scanner Upper Unit.
2 2
NOTE
The Flap Stay (3) holds the Scanner Upper Unit when opened. If you will close the Scanner Upper Unit, move it a little to open side first, and then move to close side. Move to open side first.
5-229
K105sm5eG
5-230
K105sm5eG
6. Remove 2 pieces of 4x6 screw (7) to remove the Motor Assembly (8). Replace the Motor Assembly (8) with the new one. 8
NOTE
It is possible to adjust the tension of Belt 60S2M284 (9) by moving the motor left and right. (Screws (7) must be loosed at this time.) Prepare the Tension Gage (10) and the Scale (11) like the following photo, and adjust the tension so that the bend of belt becomes 3mm when 150gf +/-50g is given. Please satisfy the following requirements when you adjust the tension. 1. Confirm that the Belt 60S2M284 (9) and Motor Pulley are surely in gear with each other. If you adjust the tension although they are not in gear, the Belt 60S2M284 (9) may be too much loosed as soon as you start machine operation. 2. Adjust the tension when the Scanner Upper Unit is closed. You can not adjust the tension properly if it is opened.
10
11
150gf +/-50g
3mm
5-231
K105sm5eG
5.12. 3
1. Remove the Scanner Unit (1) from the machine making reference to [5.12. 1 Removal of the Scanner Unit] on the page 5-220.
2. Loosen 2 piecers of screw (2), and then bring down the Tension Pulleys (3) to unfasten the Belt.
5-232
K105sm5eG
3. Remove the Belt 60S2N250 (4), and replace it with the new one. 4
NOTE
It is possible to adjust the tension of Belt 60S2M250 (4) by moving the Tension Pulleys (3) up and down. (Screws (2) must be loosed at this time.) Prepare the Tension Gage (5) and the Scale (6) like the following photo, and adjust the tension so that the bend of belt becomes 3mm when 150gf +/-50g is given. Please satisfy the following requirements when you adjust the tension. 1. Confirm that the Drive the Belt 60S2M250 (4) and Pulley Assemblies (7) are surely in gear with each other. If you adjust the tension although they are not in gear, the Belt 60S2M250 (4) may be too much loosed as soon as you start machine operation. 2. Adjust the tension when the Scanner Upper Unit is closed. You can not adjust the tension properly if it is opened. 5
2 7
2 7
150gf +/-50g
3mm
5-233
K105sm5eG
4. Loosen 2 pieces of 4x6 screw (8), and then slide the Motor Pulley (9) to the arrow direction to unfasten the Belt. 9
5. Remove the Belt 60S2M284 (10), and replace it with the new one.
10
NOTE
It is possible to adjust the tension of Belt 60S2M284 (10) by moving the Motor Pulley (9) left and right. (Screws (8) must be loosed at this time.) Adjust the tension so that the bend of belt becomes 3mm when 150gf +/-50g is given. Please satisfy the following requirements when you adjust the tension. 1. Confirm that the Drive the Belt 60S2M284 (10) and Motor Pulley (9) are surely in gear with each other. If you adjust the tension although they are not in gear, the Belt 60S2M284 (10) may be too much loosed as soon as you start machine operation. 2. Adjust the tension when the Scanner Upper Unit is closed. You can not adjust the tension properly if it is opened. 8 150gf +/-50g
3mm 10 9
5-234
K105sm5eG
5.12. 4
NOTE
If you will clean the Drive Rollers 1 and 2, use alcohol. Water is not recommended because it is not good for the rubber roller.
1. Remove the Scanner Unit (1) from the machine making reference to [5.12. 1 Removal of the Scanner Unit] on the page 5-222.
2. Pull up the Levers (2) and open the Scanner Upper Unit.
2 2
NOTE
The Flap Stay (3) holds the Scanner Upper Unit when opened. If you will close the Scanner Upper Unit, move it a little to open side first, and then move to close side. Move to open side first.
5-235
K105sm5eG
3. Remove the screw (4) of the Flap Stay, and then open the Scanner Upper Unit fully.
4. Loosen 2 pieces of screw (5), and then bring down the Tension Pulleys (6) to unfasten the Belt.
5-236
K105sm5eG
NOTE
It is possible to adjust the tension of Belt 60S2M250 (7) by moving the Tension Pulleys (6) up and down. (Screws (5) must be loosed at this time.) Prepare the Tension Gage (8) and the Scale (9) like the following photo, and adjust the tension so that the bend of belt becomes 3mm when 150gf +/-50g is given. Please follow the following requirements when you adjust the tension. 1. Confirm that the Drive the Belt 60S2M250 (7) and Pulley Assemblies (10) are surely in gear with each other. If you adjust the tension although they are not in gear, the Belt 60S2M250 (7) may be too much loosed as soon as you start machine operation. 2. Adjust the tension when the Scanner Upper Unit is closed. You can not adjust the tension properly if it is opened. 8
5 10
5 10
37
150gf +/-50g
3mm
5-237
K105sm5eG
6. Remove the 3x12 screw (11) to remove each Pulley Assembly (10).
11
10
11
10
NOTE
Be careful of the direction of Pulley Assemblies.
5-238
K105sm5eG
12
NOTE
The POM Washer is used only on the shaft of Drive Roller 1.
5-239
K105sm5eG
9. Remove the Pan Head Screw 4x8 (14) to remove P4 Pivot Washer (15) and P4 Twin Link 1 (16).
16
14
15
16
14
5-240
K105sm5eG
10. Remove the Pan Head Screw 4x8 (17) to remove P4 Pivot Washer (18) and P4 Twin Link 1 (19).
17
18 17 19
5-241
K105sm5eG
20
21
5-242
K105sm5eG
13. Remove the 2 pieces of each Retaining Ring-E (22 : E6), Polyslider Washer (23) and Bearing (24) on the right of the scanner unit.
22
24 23 22
24 23
5-243
K105sm5eG
14. Remove the Pan Head Screw 4x8 (25) to remove P4 Pivot Washer (26) and P4 Twin Link 1 (27).
25
27
26 25 27
5-244
K105sm5eG
15. Remove the Pan Head Screw 4x8 (28) to remove P4 Pivot Washer (29) and P4 Twin Link 1 (30).
30
28
29 30 28
5-245
K105sm5eG
31
NOTE
When reassemble, fit notches (33) of the P4 Sheet Guide (32) to the roller shafts (34). 34 32
33
5-246
K105sm5eG
35
35
35
5-247
K105sm5eG
20. There are 4 pieces of Holders (37) which hold the Drive Rollers 1 & 2. Remove 2 pieces of screw (38) from each Holder (37).
37
38
38 5-248
K105sm5eG
21. Rotate 4 pieces of Holder (37) 90 degrees arc revolution, and remove them.
37
37
5-249
K105sm5eG
22. Pressing down Roller Holder Assy (39), slide the Drive Roller 1 (40) to the left, and then remove it. Replace the Drive Roller 1 (39) with the new one. 39
40
40
NOTE
The longer shaft of the Drive Roller 1 shall be placed at the left side.
Left
Right
5-250
K105sm5eG
23. Pressing down Roller Holder Assy (41), slide the Drive Roller 2 (42) to the left, and then remove it. Replace the Drive Roller 2 (43) with the new one. 41
42
42
NOTE
(1) The longer shaft of the Drive Roller 1 shall be placed at the left side.
Left
Right
5-251
K105sm5eG
NOTE
(2) The pattern of Drive Rollers 1 and 2 are different. Do not replace their position each other. Drive Roller 2
Drive Roller 1
5-252
K105sm5eG
2. Disconnect 2 connectors (1) from Power Board ES (2). Open Wire Saddles (3) to release the harnesses. 3 2
1 3. Disconnect the USB cable (4) and the harness (5) from Dummy Board on Data Controller Board ES (6). Open the nylon bands (7) to release the USB cable (4). 5 4 4
NOTE
To open the nylon band (7), move up the stopper with such tool as a flat head screwdriver. 5-253
K105sm5eI
10
NOTE
Dummy Board (10) is connected to Main Board at the connectors (11). 10
11
5. Remove 3 screws (12) and the spacer (13) to release Main Board (14). 12
13
14
5-254
K105sm5eI
6. Disconnect 5 Flexible Cables (15) from the terminals on CIS Controller Board ES (16). 15 15
16
16
NOTE
(1) The shorter Flexible Cables (17) is fixed with tapes near the terminals on CIS Controller Board. Carefully remove the tapes so as not to damage Flexible Cables. Do not remove the tapes on the other (longer) ones (18) at this time.
17
18
17
18
17 (2) Fully insert Flexible Cable to the terminal on CIS Controller Board ES. If not connected firmly, the scan image may go wrong. (But be sure to handle it with great care as it is easily broken.)
5-255
K105sm5eI
7. Remove 2 screws (19) to release CIS Controller Board ES in the middle (20). 20
20
18 18
18 18
5-256
K105sm5eI
10. Remove 2 screws (22) to release CIS Controller Board ES on the second from the left (23). 23 23
24
24
12. Gently lift up Base Plate (25) and remove it so that Flexible Cables passes through the square holes to avoid damage. 25
25
25
5-257
K105sm5eI
NOTE
This section is for the machines before S/N 10512993, 10513110-10513136. For S/N 10512994 10513109, 10513137 and after, refer to [5.12.5.1 Removal of Base Plate] on page 5-253.
1. Remove Scanner Unit (1) from the machine making reference to [5.12. 1 Removal of Scanner Unit] on the page 5-222.
2. Disconnect 2 connectors (2), open the Wire Saddles (3) to release the harnesses.
5-258
K105sm5eI
3. Disconnect the USB Connector (4), and open the Nylon Bands (5) to release the USB Cable. 4 5
NOTE
To open the Nylon Band (5), move up the stopper with such tool as a minus screwdriver. 4. Remove 4 screws (7) to release Data Controller PCB. (You do not have to disconnect any connector from Data Controller PCB.) 7
5-259
K105sm5eI
5. Disconnect all of the Flexible Cables (8) from each CIS Controller Board. (Handle with great care not to break the Flexible Cable at this time!)
5-260
K105sm5eI
NOTE
(1) Insert Flexible Cable (8) fully to the CIS Controller PCB terminal when you connect it. If not connected firmly, the scan image may go wrong. (But be sure to handle it with great care as it is easily broken.
(2) Each Flexible Cable is fixed with the tapes (9). Strip off the tape (9) to make the Flexible Cable free. 9
(3) The central one of Flexible Cable is running under the Data Controller PCB and the CIS Controller PCB. Remove the Ring (10), strip off the tape (11) under the Data Controller PCB, and then put the Flexible Cable aside.
10
11
5-261
K105sm5eI
12
12
13
NOTE
Carefully remove Base Plate (13) not to damage Flexible Cables at this time!
5-262
K105sm5eI
Label
1. Remove Scanner Unit (1) from the machine. Remove Base Plate (2). Refer to [5.12.1 Removal of Scanner Unit] on page 5-222 and [5.12.5.1 / 5.12.5.2 Removal of Base Plate].)
5-263
K105sm5eI
3 3. Remove 4 screws (5) and remove CIS Assembly (4). Replace CIS Assembly (4) with a new one.
4 5
NOTE
There are screws (6) around the Counter Roller, which are locked with the paint. Do not loosen or tighten these screws (6) as they maintain the focus adjustment! (Focus has been adjusted in the factory.) You will spoil the focus adjustment if you loosen or tighten it!
6 6
NOTE
Be sure to perform scanner adjustments (Shading, Calibration (if supported), Feed Distance and Position) after replacing CIS Assembly. See [8.12 Scanner Utility] on page 8-185 for adjustment.
5-264
K105sm5eI
Gap Rollers
(2) 2 of all the 8 Gap Rollers are slightly wider, 2 types of Gap Roller replacement kits are provided. Gap Roller Replacement Kit: Z058000750
1. Remove Scanner Unit (1) from the machine. Remove Base Plate (2). Refer to [5.12.1 Removal of Scanner Unit] on page 5-222 and [5.12.5.1 / 5.12.5.2 Removal of Base Plate].) 2
5-265
K105sm5eJ
2. Remove 2 screws (3) and remove the Gap Roller Assembly (4).
3. Remove 4 screws (5), and replace the Gap Roller (6) with the new one.
NOTE
Gap Rollers shaft (7) is shaped like D, and its flat face should be aligned with the sloping edge (8) of the bracket as the following Correct case. 8
Correct
Wrong: Flat face and sloping edge are not aligned with each other.
5-266
K105sm5eJ
4. Turn 4 screws (5) lightly just to hold the Inside Bracket (9) temporarily. (Inside Bracket (9) must be slid to front and rear by hand.) 5 5
5. Install the Gap Roller Assembly (4) to the scanner unit with 2 screws (3). (Turn these screws tightly.)
NOTE
Be careful of the direction of Gap Roller Assembly (4).
Front side
Rear side
5-267
K105sm5eJ
6. 4 Gap Roller Assemblies (10) and 2 POM Roller Assemblies (11) belong to 3 front CIS. If you replaced any of these 4 Gap Roller Assemblies (10) on the front, you must adjust the rest of 3 Gap Roller Assemblies (10) and 2 POM Roller Assemblies (11). Therefore loosen the screws (12) of all these assemblies. (Do not loosen screws so much. Just holding the Inside Bracket temporarily is enough.) And 4 Gap Roller Assemblies (13) belong to 2 rear CIS. If you replaced any of these 4 Gap Roller Assemblies (13) on the front, you must adjust the rest of 3 Gap Roller Assemblies (13). Similarly loosen the screws (14) of all other assemblies. 13 13
Rear CIS
Rear CIS
Front CIS
Front CIS
Front CIS
11
10
11
14
13
10
12
11
12 12
11
5-268
K105sm5eJ
8. Put 3 pieces (for the front) or 2 pieces (for the rear) of Adjustment Plastic Sheet (15: 0.3mm thick) between Feed Roller and Scan Glass. When adjusting the Gap Roller on the front
15
15
NOTE
Do not put the Adjustment Plastic Sheet (15) under the Gap Roller!
5-269
K105sm5eJ
9. Slide the Inside Bracket (16) gently in the direction of arrow until it is stopped. When stopped, turn the screws (12) or (14) to fix the Inside Bracket (16).
14
14
16 12 12
16
NOTE
(1) Fix the Inside Bracket of Gap Roller Assemblies and POM Roller Assemblies on the front side in the following order.
1st
5th
3rd
4th
6th
2nd
5-270
K105sm5eJ
NOTE
(2) Fix the Inside Bracket of Gap Roller Assemblies on the rear side in the following order. 1st 3rd 4th 2nd
10. Open the scanner upper unit and remove Adjustment Plastic Sheets (15). Close the scanner upper unit.
15
5-271
K105sm5eJ
11. Insert the Confirmation Plastic Sheet (17: 0.1mm thick) between Feed Roller and Scan Glass to check if the gap is correct at everywhere. If not correct, repeat from the step 6.
17 17
NOTE
Be sure to perform scanner adjustments (Shading, Calibration (if supported), Feed Distance and Position) after replacing Gap Rollers. See [8.12 Scanner Utility] on page 8-185 for adjustment.
5-272
K105sm5eJ
Chapter 6 Maintenance
6. 1 6. 2 6. 3
page 6- 2 6- 3 6- 4
K105sn6e1_EUA
6. 1
For keeping the machine quality in a satisfactory level, a periodic replacement for the following parts is recommended. A damaged part (even if it looks not) may result in a critical failure. Used area Developer Unit Part Name Roller Developer Sheet 3 Sheet 4 Seal 1 Seal 3 Seal 4 Scraper Roller Supply Sheet 5 Sheet 6 Corona Wire 1 Assy Corona Wire Filter Filter 2 Roller Fusing Bush Nail Stripping Nail Lower Photoconductive Drum Quantity 1 2 2 2 2 2 1 1 2 2 1 2 1 2 1 2 13 6 1 Remarks Contained in Developer Maintenance Kit E (Z050980280)
Image Corona Transfer / Separation Corona Main Frame Fuser Upper Area Fuser Unit
Engine Frame
6-2
K105sn6e1_EUA
6. 2
CL: cleaning GR: greasing
Unit / Area Developer Unit Fuser Unit
Maintenance Period
Please make the following maintenances to keep the machine in a good condition and to get a superior image.
Maintenance part Counter Roller Roller Fusing Roller Pressure Nail Stripping Nail Lower Thermistor Thermostat Corona Wire Corona Housing
Remarks Clean with a cloth impregnated with alcohol. Clean with a cloth impregnated with alcohol. Clean with a cloth impregnated with alcohol. Clean with a dry cloth. Clean with a dry cloth. Clean with a dry cloth. Clean with a dry cloth. Clean with a cloth impregnated with water then with a dry cloth. Clean with a cloth impregnated with water then with a dry cloth. Clean with a cloth impregnated with water then with a dry cloth. Clean with a cloth impregnated with water then with a dry cloth. Clean with a dry cloth. Read [5. 5. 2 Cleaning of Photoconductive Drum] for the way of cleaning. Lubricate the gears.
Image Corona
Corona Wire Corona Housing LED Head (Selfoc Lens) Photoconductive Drum Machine inside Drive Plastic Gears
6-3
K105sn6e1_EUA
6. 3
Service Kits
The following service kits are assigned taking the serviceability into consideration.
Kit Name (Part Number for Kit) Start Up Kit (Z050980010) Developer Maintenance Kit E (Z050980280) Included Parts Toner Cartridge Kit Starting Toner (500g) Roller Developer Sheet 3 Sheet 4 Seal 1 Seal 3 Seal 4 Scraper Roller Supply Sheet 5 Sheet 6 Sheet 3 Sheet 4 Seal 1 Seal 3 Seal 4 Sheet 5 Sheet 6 Corona Wire 1 Assy Corona Wire Filter Filter 2 Roller Fusing Bush Nail Stripping Nail Lower Toner Cartridge (300g) Photoconductive Drum Quantity 1 1 1 2 2 2 2 2 1 1 2 2 2 2 2 2 2 2 2 1 2 1 2 1 2 13 6 2 1 Remarks During installation
Corona Wire Kit (Z050980040) Filter Kit (Z050980050) Fuser Maintenance Kit (Z050980060)
6-4
K105sn6e1_EUA
Chapter 7 Troubleshooting
Page 7- 3 7- 3 7- 3 7- 4 7- 5 7- 6 7- 6 7- 7 7- 7 7- 7 7- 7 7- 8 7- 9 7-10 7-10 7-11 7-13 7-14 7-15 7-15 7-16 7-16 7-17 7-17 7-18 7-18 7-19 7-19 7-20 7-20 7-21 7-21 7-23 7-24 7-25 7-25 7-26 7-26 7-27 7-28 7-29 7-29 7-30 7-30
K105sm7e1_EUA
7. 1 Troubleshooting - Printer Errors 7. 1. 1 Countermeasures - Call Operator Errors 7. 1. 1. 1 Roll 2 Feeding Jam Delay (J-0101) 7. 1. 1. 2 Roll 1 Feeding Jam Delay (J-0102) 7. 1. 1. 3 Feeding Jam Delay (J-0103) & Early (J-0303) 7. 1. 1. 4 Reg. Jam Delay (J-0104), Stay (J-0204) Early (J-0304), Remained (J-1004) 7. 1. 1. 5 Internal Jam Delay (J-0106), Stay (J-0206) Early (J-0306), Remained (J-1006) 7. 1. 1. 6 Fuser Jam Delay (J-0107), Stay (J-0207) Early (J-0307), Remained (J-1007) 7. 1. 1. 7 Paper jam by opening the Roll Deck during printing (J-1100) 7. 1. 1. 8 Paper jam by opening the Exit Cover during printing (J-1200) 7. 1. 1. 9 Deck Open 7. 1. 1.10 Deck Jam 7. 1. 1.11 Manual Set NG 7. 1. 1.12 Toner Empty 7. 1. 1.13 The door opened during the print 7. 1. 2 Countermeasures - Call Service Errors 7. 1. 2. 1 Fuser Error (E-000, E-002 & E-004) 7. 1. 2. 2 Fuser Error (E-001) 7. 1. 2. 3 Fuser Error (E-003) 7. 1. 2. 4 Main Motor Error (E-010) 7. 1. 2. 5 Fuser Motor Error (E-011) 7. 1. 2. 6 Developer Press Motor Error (E-012) 7. 1. 2. 7 Counter Error (E-020) 7. 1. 2. 8 High Voltage Output Error (E-031, E-032 & E-033) 7. 1. 2. 9 Developer Bias Output Error (E-034) 7. 1. 2.10 Cutter Error (E-040) 7. 1. 2.11 FPGA Error (E-050) 7. 1. 2.12 Developer Error (E-070) 7. 2 Troubleshooting - Image Quality Defects 7. 2. 1 Basic Image Adjustment 7. 2. 2 Countermeasures - Image Quality Defects 7. 2. 2. 1 Halftone is too light 7. 2. 2. 2 Halftone and solid black are too light 7. 2. 2. 3 The whole image is extremely light 7. 2. 2. 4 Density is uneven 7. 2. 2. 5 Totally appeared foggy image 7. 2. 2. 6 Foggy image or blurred black wide line (vertical) 7. 2. 2. 7 Clear black thin line (vertical) 7. 2. 2. 8 White line (Vertical) 7. 2. 2. 9 Void of image 7. 2. 2.10 Dirt on the back of the print 7. 2. 2.11 Defective fusing 7. 2. 2.12 Defective image placement, No Leading Edge 7. 2. 2.13 Jitter 7-1
Image looks not sharp Uneven image density (vertical) Completely white (No image) Completely black Crease of paper Double image Dirt on the print (Offset)
7-31 7-31 7-32 7-32 7-33 7-34 7-35 7-36 7-36 7-36 7-36 7-36 7-37 7-37 7-37 7-38 7-38 7-38 7-39 7-39 7-39 7-39 7-39 7-40
7. 3 Troubleshooting - Scanner Defects 7. 3. 1 Countermeasures - scanner operation 7. 3. 1. 1 Original can not be set (Scanner does not transport) 7. 3. 1. 2 Scanner does not start scanning from the original set position 7. 3. 1. 3 Original can not be set (Original feeding does not stop) 7. 3. 1. 4 Original is mis-fed 7. 3. 1. 5 Motor rotates endlessly at the time of turning on 7. 3. 1. 6 Scanner is not recognized 7. 3. 2 Countermeasures - scanner image quality 7. 3. 2. 1 Completely black 7. 3. 2. 2 Vertical black lines 7. 3. 2. 3 Vertical white lines 7. 3. 2. 4 Some image is lost at the boundary of Image Blocks 7. 3. 2. 5 Vertical image gap between Image Blocks 7. 3. 2. 6 Image quality is not good 7. 3. 2. 7 Density is different between left and right 7. 4 Touch Screen Calibration
7-2
K105sm7e1_EUA
7. 1
7. 1. 1
7. 1. 1. 1
Reference
Delay Stay Early Remained
Cause Installation of roll paper Roll 2 Set Sensor (PH9)
: Paper arrives the sensor much later than required timing. : Paper exists on the sensor for longer time than required. : Paper arrives the sensor much earlier than required timing. : Paper has already existed on the sensor when turning on the machine.
Checking order 1 2 Checking Is the roll paper correctly installed to the Roll Deck 2? Check the status of Roll 2 Set Sensor in the Device Status Mode of the Service Mode. Signal Code : 090 (Roll 2 Set Sensor) Is the status H when the roll paper is set? (Refer to the page 8-9 as for the Device Status Mode.) Result No No Treatment Install it correctly. 1. Is there any problem with the Drawer Connector which connects the machine and the Roll Deck. 2. Check if there is any problem with the wire connected to the Roll 2 Set Sensor. 3. Replace the Roll 2 Set Sensor if there is no problem with the wire. 1. Check if there is any problem with the wire connected to the Roll 2 Feed Clutch. 2. Replace the Roll 2 Feed Clutch if there is no problem with the wire.
Check the operation of Roll 2 Feed Clutch in the Device Operation Mode of the Service Mode. Signal Code : 08 (Roll 2 Feed Clutch) Does the clutch operate when you change the output signal from L to H? (Refer to the page 8-16 as for the Device Operation Mode.) Check the status of Roll 2 Set Sensor in the Device Status Mode of the Service Mode while making the following operation. (Signal Code : 090) 1. Set the leading edge of roll 2 between feeding rollers. (Leading edge must not pass over the Roll 2 Set Sensor.) 2. Close the Roll Deck. Does the status change from L to H when the machine is transporting the paper? Roll 2 Set Sensor
No
No
1. Check the driving belts of the Roll Deck. 2. Check if there is any problem with the wire connected to the Main Motor. 3. Replace the Main Motor if there is no problem with the wire. 1. Remove the whole Roll Deck, and then re-install it to the machine correctly.
Yes
7-3
K105sm7e1_EUA
7. 1. 1. 2
Cause
Check the operation of Roll 1 Feed Clutch in the Device Operation Mode of the Service Mode. Signal Code : 06 (Roll 1 Feed Clutch) Does the clutch operate when you change the output signal from L to H? (Refer to the page 8-16 as for the Device Operation Mode.) Check the status of Roll 1 Set Sensor in the Device Status Mode of the Service Mode while making the following operation. (Signal Code : 089) 1. Set the leading edge of roll 1 between feeding rollers. (Leading edge must not pass over the Roll 1 Set Sensor.) 2. Close the Roll Deck. Does the status change from L to H when the machine is transporting the paper? Roll 1 Set Sensor
No
No
1. Check the driving belts of the Roll Deck. 2. Check if there is any problem with the wire connected to the Main Motor. 3. Replace the Main Motor if there is no problem with the wire. 1. Remove the whole Roll Deck, and then re-install it to the machine correctly.
Yes
7-4
K105sm7e1_EUA
7. 1. 1. 3
Cause
Check the status of Cutter Home Position Sensors in the Device Status Mode of the Service Mode. Signal Code 078 (Cutter Home Position Sensor Right) 079 (Cutter Home Position Sensor Left) Is the status H when the Cutter is at each home position? And is it L when the Cutter is not at the home position? (Refer to the page 8-9 as for the Device Status Mode.) Check the operation of Feed Clutch in the Device Operation Mode of the Service Mode. Signal Code : 10 (Feed Clutch) Also open and close the Roll Deck, and check if the Main Motor rotates correctly. Does each Feed Clutch and Main Motor operate correctly? (Refer to the page 8-16 as for the Device Operation Mode.)
No
Driving mechanism
No
7-5
K105sm7e1_EUA
7. 1. 1. 4
Cause
Reg. Jam Delay (J-0104), Stay (J-0204) Early (J-0304), Remained (J-1004)
Checking order 1 2 Checking Does the paper mis-fed occur around the Registration Roller? Check the status of Registration Sensor in the Device Status Mode of the Service Mode. Signal Code : 084 (Registration Sensor) Is the status L when the paper is not passing beside the sensor? And is it H when the paper is passing beside the sensor? (Refer to the page 8-9 as for the Device Status Mode.) Is the Engine Unit closed firmly until it is locked? (Is the pressure around the Registration Roller correct?) Check the operation of Registration Clutch in the Device Operation Mode of the Service Mode. Signal Code : 11 (Registration Clutch) Also open and close the Roll Deck, and check if the Main Motor rotates correctly. Does each Registration Clutch and Main Motor operate correctly? (Refer to the page 8-16 as for the Device Operation Mode.) Result Yes No Treatment Remove the mis-fed paper. 1. Check if there is any problem with the wire connected to the Registration Sensor. 2. Replace the Registration Sensor if there is no problem with the wire.
Engine Unit
No
1. Close the Engine Unit firmly. 2. Adjust the pressure around the Registration Roller. Replace the Registration Clutch or Main Motor if it is defective.
Driving mechanism
No
7. 1. 1. 5
Cause
Internal Jam Delay (J-0106), Stay (J-0206) Early (J-0306), Remained (J-1006)
Checking order 1 2 Checking Does the paper mis-fed occur around the separation area? Check the status of Separation Sensor in the Device Status Mode of the Service Mode. Signal Code : 010 (Separation Sensor) Is the status L when the paper is not passing beside the sensor? And is it H when the paper is passing beside the sensor? (Refer to the page 8-9 as for the Device Status Mode.) Is the Transfer / Separation Corona Unit installed to the machine correctly? Is the Corona Wire broken? Is the output from the HV Power Supply to the Separation Corona correct? Result Yes No Treatment Remove the mis-fed paper. 1. Check if there is any problem with the wire connected to the Separation Sensor. 2. Replace the Separation Sensor if there is no problem with the wire.
Yes
HV Power Supply
Yes No
Install the Transfer / Separation Corona Unit correctly. Replace the Corona Wire. Replace the HV Power Supply. K105sm7e1_EUA
7-6
7. 1. 1. 6
Cause
Fuser Jam Delay (J-0107), Stay (J-0207) Early (J-0307), Remained (J-1007)
Checking order 1 2 Checking Does the paper mis-fed occur around the fuser area? Check the status of Exit Sensor in the Device Status Mode of the Service Mode. Signal Code : 011 (Exit Sensor) Is the status L when the paper is not passing beside the sensor? And is it H when the paper is passing beside the sensor? (Refer to the page 8-9 as for the Device Status Mode.) 2. Replace the Exit Sensor if there is no problem with the wire. Result Yes No Treatment Remove the mis-fed paper. 1. Check if there is any problem with the wire connected to the Exit Sensor.
7. 1. 1. 7
Cause Opening the Roll Deck
No
Close it firmly.
7. 1. 1. 8
Cause Opening the Exit Cover
7. 1. 1. 9
Cause Roll Deck Switch (MS5)
Deck Open
Checking order 1 2 Checking Is the Roll Deck opened? Check the status of the following signal in the Device Status Mode of the Service Mode. Signal Code : 009 (Roll Deck Open Signal) Is the status L when the Roll Deck is closed? And is it H when the Roll Deck is opened? (Refer to the page 8-9 as for the Device Status Mode.) Result Yes No Treatment Close it firmly. 1. Check if there is any problem with the wire connected to the Switch (MS5). 2. Replace the Switch (MS5) if there is no problem with the wire.
7-7
K105sm7e1_EUA
7. 1. 1.10
Cause Mis-feed of paper Installation of roll paper Roll 1 Set Sensor (PH7) Roll 2 Set Sensor (PH9)
Deck Jam
Checking order 1 2 3 Checking Does the paper mis-fed occur in the Roll Deck? Is the roll paper correctly installed to the Roll Deck 2? Check the status of Roll 1 Set Sensor and Roll 2 Set Sensor in the Device Status Mode of the Service Mode. Signal Code : 089 (Roll 1 Set Sensor) 090 (Roll 2 Set Sensor) Is the status of each sensor H when you set the roll paper? (Refer to the page 8-9 as for the Device Status Mode.) Result Yes No No Treatment Remove the mis-fed paper. Install it correctly. 1. Is there any problem with the Drawer Connector which connects the machine and the Roll Deck. 2. Check if there is any problem with the wire connected to each sensor. 3. Replace the concerning sensor if there is no problem with the wire. 1. Check if there is any problem with the wire connected to each clutch. 2. Replace the concerning clutch if there is no problem with the wire.
Roll 1 Feed Clutch (CL4) Roll 2 Feed Clutch (CL6) Roll 1 Back Clutch (CL5) Roll 2 Back Clutch (CL7)
Check the operation of the following clutches in the Device Operation Mode of the Service Mode. Signal Code 06 (Roll 1 Feed Clutch) 07 (Roll 1 Back Clutch) 08 (Roll 2 Feed Clutch) 09 (Roll 2 Back Clutch) Does each clutch operate correctly? (Refer to the page 8-16 as for the Device Operation Mode.) Check the status of Roll 1 Set Sensor and Roll 2 Set Sensor in the Device Status Mode of the Service Mode while making the following operation. Signal Code : 089 (Roll 1 Set Sensor) 090 (Roll 2 Set Sensor) 1. Set the leading edge of each roll paper between the concerning feeding rollers. (Leading edge must not pass over each Roll 1 (2) Set Sensor.) 2. Close the Roll Deck. Does the status change from L to H when the machine is transporting the paper? Roll 1 Set Sensor
No
No
1. Check the driving belts of the Roll Deck. 2. Check if there is any problem with the wire connected to the Main Motor. 3. Replace the Main Motor if there is no problem with the wire. 1. Remove the whole Roll Deck, and then re-install it to the machine correctly.
Yes
7-8
K105sm7e1_EUA
7. 1. 1.11
Cause Mis-feed
Manual Set NG
Checking order 1 2 Checking Have you already set the cut sheet paper to the Bypass Feeder before you turned on the machine? Check the status of Manual Feed Sensor in the Device Status Mode of the Service Mode. Signal Code : 008 (Manual Set Sensor) Is the status L when the paper is not passing beside the sensor? And is it H when the paper is passing beside the sensor? (Refer to the page 8-9 as for the Device Status Mode.) Check the status of Registration Sensor in the Device Status Mode of the Service Mode. Signal Code : 084 (Registration Sensor) Is the status L when the paper is not passing beside the sensor? And is it H when the paper is passing beside the sensor? (Refer to the page 8-9 as for the Device Status Mode.) Is the Engine Unit closed firmly until it is locked? (Is the pressure around the Registration Roller correct?) Check the operation of Registration Clutch in the Device Operation Mode of the Service Mode. Signal Code : 11 (Registration Clutch) Also open and close the Roll Deck, and check if the Main Motor rotates correctly. Does each Registration Clutch and Main Motor operate correctly? (Refer to the page 8-16 as for the Device Operation Mode.) 2. Replace the Manual Set Sensor if there is no problem with the wire. Result Yes No Treatment Remove the paper. 1. Check if there is any problem with the wire connected to the Manual Set Sensor.
Registration Sensor
No
1. Check if there is any problem with the wire connected to the Registration Sensor. 2. Replace the Registration Sensor if there is no problem with the wire.
Engine Unit
No
1. Close the Engine Unit firmly. 2. Adjust the pressure around the Registration Roller. Replace the Registration Clutch or Main Motor if it is defective.
Driving mechanism
No
7-9
K105sm7e1_EUA
7. 1. 1.12
Cause Toner Cartridge Toner Supply Motor (M3)
Toner Empty
Checking order 1 2 Checking Is there enough toner in the Toner Cartridge? Check the operation of Toner Supply Motor by the following 2 ways. 1. Turn on the machine, and check the action of Toner Supply Motor at that time. 2. Select the Factory Adjustment Mode, and carry out the Sub Mode No.05. Press the [ * ] Key when the machine is operating. (The Toner Supply Motor rotates when you are pressing the [ * ] Key.) Does the Toner Supply Motor operate correctly in both cases? (Refer to the page 8-154 as for the Factory Adjustment Mode.) Confirm that the Toner Sensor is not buried in the toner. Then check the status of Toner Sensor in the Input/Output Mode of the Service Mode. Signal Code : 091 (Toner Sensor) Is the status H when the Toner Sensor is covered with the toner? And is it L when the sensor is not covered? (Refer to the page 8-9 as for the Device Status Mode.) Result No No Treatment Replace the Toner Cartridge. 1. Check if there is any problem with the wires among Toner Supply Motor, Driver PCB B and PW10522 PCB. 2. Replace the Toner Supply Motor if there is no problem with the wire.
No Yes
7. 1. 1.13
Cause
Mis-feed of paper
Switch (MS5)
Check the status of the following signal in the Device Status Mode of the Service Mode. Signal Code : 009 (Roll Deck Open Signal) Is the status L when the Roll Deck is closed? And is it H when the Roll Deck is opened? (Refer to the page 8-9 as for the Device Status Mode.)
No
7-10
K105sm7e1_EUA
7. 1. 2
The followings are the names of Service Call Errors and the conditions that those errors occur. Error Code E-000 E-001 E-002
E-003 E-004
Fuser Temperature Abnormal Fall Error Fuser Temperature Abnormal Fall Error
E-010
E-011
E-012 E-020
E-031
E-032
E-033
7-11
K105sm7e1_EUA
E-040
Cutter Error
E-050 E-070
Conditions The Developer Bias Output Detection Signal (BIAS_LD) continues to be L for 1 second or longer when the Developer Bias is supplied to the Developer Unit. 1. The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R) does not change to H within 100 millisecond since the Cutter has started the operation. 2. The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R) does not change to L within 1 second since the Cutter has started the operation. Initialization of FPGA is failed after turning on. 1. The Connector J-253 is not connected. 2. The Switch (MS4) is open condition, which detects open/close of Engine Unit or Toner Hatch.
7-12
K105sm7e1_EUA
7. 1. 2. 1
E-000 : Fuser Temperature Rising Error E-002 : Fuser Low Temperature Error E-004 : Fuser Temperature Abnormal Fall Error
Cause Error clearance Checking order 1 Checking Have you cleared the fuser error in the Error Clear Mode? (Refer to the page 8-158 as for the Error Clear Mode.) Are wires among Lamp (H1), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? Unplug the machine, and then check the resistance of Lamp (H1) with the multimeter. Is it 15 ohm or lower? Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? (Refer to the page 8-12 as for the Information Mode.) Confirm that the machine is turned on, and then check the voltage of the orange line (J220-4). Is it 24V? Confirm that the machine is turned off, and then check whether or not each Fuse is broken. Relay (RY1) 6 Is any Fuse broken? Select the Device Operation Mode, and then change the signal of the following signal to H. Signal Code : 22 (Fuser Relay) And check the resistance between the following points. Between RY1-2 and RY1-4 Between RY1-6 and RY1-8 Is the each resistance almost 0 ohm? (Refer to the page 8-16 as for the Device Operation Mode.) Result Yes Treatment Wait until the Fuser Unit is enough cooled down. Then select the Error Clear Mode and clear the concerning error. Connect them properly.
Wires
No
Lamp (H1)
No
No
No
Yes
No
7-13
K105sm7e1_EUA
Checking order 7
Checking Select the Device Operation Mode, and then change the signal of the following signals to H. Signal Code : 22 (Fuser Relay) 21 (Fuser Lamp 1) Then check the voltage between J105-1 and J105-2. Is it 0V? Refer to the page 8-16 as for the Device Operation Mode.) CAUTION Change the signal of 21 (Fuser Lamp 1) to L after checking!
Result Yes No
Treatment Replace the Solid State Relay Replace the PW10522 PCB.
7. 1. 2. 2
Cause Error clearance
Wires
No
3 4
Yes No
7-14
K105sm7e1_EUA
7. 1. 2. 3
Cause Error clearance
Wires
No
No
7. 1. 2. 4
Cause Wires
Yes
Is any Fuse broken? Check the operation of Main Motor in the Device Operation Mode of the Service Mode. Signal Code : 00 (Main Motor) Does the Main Motor operate correctly? (Refer to the page 8-16 as for the Device Operation Mode.)
No
7-15
K105sm7e1_EUA
7. 1. 2. 5
Cause Wires
Yes
Is any Fuse broken? Check the operation of Fuser Motor in the Device Operation Mode of the Service Mode. Signal Code : 01 (Fuser Motor) Does the Fuser Motor operate correctly? (Refer to the page 8-16 as for the Device Operation Mode.)
No
7. 1. 2. 6
Cause Wires
Developer Press Motor (M4) Driver PCB B (PW6654) Developer Press Sensor (PH4)
No
Replace the Developer Press Motor or Driver PCB B. Replace the Developer Press Sensor.
No
7-16
K105sm7e1_EUA
7. 1. 2. 7
Cause Wires
Yes
Counter
Is any Fuse broken? Check the operation of Counter in the Device Operation Mode of the Service Mode. Signal Code : 26 (Counter) Does the Counter operate correctly? (Refer to the page 8-16 as for the Device Operation Mode.)
No
7. 1. 2. 8
E-031 : Image Corona Output Error E-032 : Separation Corona Output Error E-033 : Transfer Corona Output Error
Cause Wires Image Corona Checking order 1 2 Checking Are wires among Image Corona, HV Power Supply PCB and PW10522 PCB connected properly? Is the Image Corona dirty? Is the Corona Wire broken? Is the Transfer Corona dirty? Is the Corona Wire broken? Is the Separation Corona dirty? Is the Corona Wire broken? Can you fix the problem if you replace the HV Power Supply? Result No Yes Yes Yes Yes Yes Yes Yes Treatment Connect them properly. Clean each Corona Wire, Grid Plate and housing. Replace the Corona Wire. Clean each Corona Wire and housing. Replace the Corona Wire. Clean each Corona Wire and housing. Replace the Corona Wire. OK
Transfer Corona
Separation Corona
HV Power Supply
7-17
K105sm7e1_EUA
7. 1. 2. 9
Cause Wires Developer Unit
Yes
GND
Multi-meter
HV Power Supply
Can you fix the problem if you replace the HV Power Supply?
Yes
OK
7. 1. 2.10
Cause Wires Cutter Home Position Sensors (MS6 & MS7)
No
7-18
K105sm7e1_EUA
7. 1. 2.11
Cause PW10522 PCB
7. 1. 2.12
Cause Wires Switch (MS4)
7-19
K105sm7e1_EUA
7. 2
7. 2. 1
The followings are the settings specified to the image creation components. When a defective image is printed out, please check whether or not these settings are satisfied for the beginning.
Component Image Corona Checking point CP11 (+) CPCOM (-) Designated voltage 1.3 +/-0.05VDC Way of adjustment VR101 Height of Corona Wire
11mm Transfer Corona CP21 (+) CP22 (-) 1.0 +/-0.05VDC VR201 Service Mode 04-029 (Plain) 04-030(Tracing) 04-031(Film)
10 or 11 mm
NOTE
There are 2 types of Tr/St Corona Assy, they differs from the position and the number of plastic sheets on the housing. A specified height for a corona wire depends on the Assy type. Separation Corona (AC) CP31 (+) CPCOM (-) 5.0 +/-0.05V
1 sheet type
Transfer Separation
2 sheets type
Transfer Separation
10mm
11mm
11mm
11mm
VR302
11mm Separation Corona (DC) Negative Developer Roller Bias Positive Developer Roller Bias Toner Supply Roller Bias (On printing) CP33 (+) Ground (-) OUTPUT2 (+) Ground (-) OUTPUT2 (+) Ground (-) TAB2 OUT1OUT (+) OUTPUT2 (-) -250 +/-5VDC -230 +/-5VDC VR303 Service Mode 04-022 (Plain) 04-023(Tracing) 04-024(Film) VR401 -
+350 +/-5VDC (Brush type) Same voltage with Developer Roller Bias (Sponge type) -150 +/-5VDC (Brush type) Same voltage with Developer Roller Bias (Sponge type) -50 +/-5VDC -40 +/-5VDC +450 +/-5VDC -550 +/-5VDC
VR601 -
Regulation Roller Bias Positive Cleaning Roller Bias Negative Cleaning Roller Bias
OUTPUT3 (+) OUTPUT2 (-) OUTPUT (+) Ground (-) OUTPUT (+) Ground (-)
7-20
7. 2. 2
7. 2. 2. 1
Check the following matters with the Test Pattern No.1 and No.3. If necessary use other Test Patterns.
Cause Checking order 1 Checking Try to readjust each image creation component according to [7.2.1 Basic Image Adjustment] on the page 7-20. Is the problem fixed? Is the Lens Array of LED Head dirty? Can you fix the problem if you use a newly unpacked paper? Result Yes OK Treatment
2 3
Yes Yes
Image Corona
Yes
No
Eraser Lamp
No
Separation Lamp
No
Transfer Corona
Is the Transfer / Separation Corona dirty? Is the input voltage to the Transfer Corona correct?
Yes
No
Is each Electrode Plate on the right of the Developer Unit surely contacted to the Electrode Plate on the machine side? Can you fix the problem if you replace the HV Power Supply PCB?
No
Yes
Clean it. 1. If the paper was humidified, instruct the customer of the way store the paper. 2. If the paper was not the specified one, explain the customer that some image problem may occur in that case. Clean each Corona Wire, Grid Plate and housing, or replace the Corona Wire if it is too dirty. Readjust the input voltage making reference to [4. 3. 2 Check & Adjustment of Analog Voltage to the Image Corona] on the page 4-33. Or replace the HV Power Supply PCB. 1. Check the wire connected to the Eraser Lamp. 2. Check or replace the Eraser Lamp. 1. Check the wire connected to the Separation Lamp. 2. Check or replace the Separation Lamp. Clean each Corona Wire and housing, or replace the Corona Wire if it is too dirty. Readjust the input voltage making reference to [4. 3. 3 Check & Adjustment of Analog Voltage to the Transfer Corona] on the page 4-35. Or replace the HV Power Supply PCB. Try to install the Developer Unit so that they are contacted each other. And supply the conductive grease to the Electrode Plates. OK
7-21
K105sm7e2_EUA
Checking order 10
Checking Is the driving gear on the left of the Developer Unit surely fitted to the driving mechanism on machine side? Is the Developer Roller evenly covered with the toner?
Result No
Treatment Check whether or not the Cam of Developer Press Unit surely presses the Developer Unit. Check the concerning gears. Check the whole Developer Unit to find the cause. Replace the Photoconductive Drum.
Developer Unit
11
No Yes
7-22
K105sm7e2_EUA
7. 2. 2. 2
Check the following matters with the Test Pattern No.1 and No.3. If necessary use other Test Patterns.
Cause Checking order 1 Checking Try to readjust each image creation component according to [7.2.1 Basic Image Adjustment] on the page 7-20. Is the problem fixed? Turn off the machine in the middle of printing, and then check the toner image on the Drum. Is the toner image looks normal? Is the Transfer/Separation Corona installed to the machine correctly? Is the high voltage of Transfer Corona leaking? Can you fix the problem if you use a newly unpacked paper? Result Yes OK Treatment
Yes No
Transfer Corona
No Yes Yes
Install it correctly. Clean the Transfer Corona. 1. If the paper was humidified, instruct the customer of the way store the paper. 2. If the paper was not the specified one, explain the customer that some image problem may occur in that case. Replace the Lead Wire.
Paper
Lead Wire
Is the resistance of Lead Wire about 10 kilo ohms, which connects the HV Power Supply and the Transfer Corona? Is a correct voltage supplied from the HV Power Supply to the Transfer Corona?
No
No
7 8 9
Is the LED Head dirty? Is the Developer Roller evenly covered with the toner? Is the Developer Unit firmly pressed toward the Drum? (Are Counter Rollers at both sides of the Developer Roller touching the Drum Unit?) Is the driving gear on the left of the Developer Unit surely fitted to the driving mechanism on machine side? Is there enough toner in the Developer Unit?
Yes No No
Readjust the input voltage making reference to [4. 3. 3 Check & Adjustment of Analog Voltage to the Transfer Corona] on the page 4-35. Or replace the HV Power Supply PCB. Clean it. Check the whole Developer Unit to find the cause. Remove the Developer Unit, and then install it to the machine correctly. Check the Developer Press Unit. Check whether or not the Cam of Developer Press Unit surely presses the Developer Unit. Check the concerning gears. 1. Check the wire or the connector connected to the Toner Sensor. 2. Check the Toner Sensor. Replace the Photoconductive Drum.
10
No
Toner Sensor
11
No
Yes
7-23
K105sm7e2_EUA
7. 2. 2. 3
Check the following matters with the Test Pattern No.1 and No.3. If necessary use other Test Patterns.
Cause Checking order 1 Checking Try to readjust each image creation component according to [7.2.1 Basic Image Adjustment] on the page 7-20. Is the problem fixed? Can you fix the problem if you use a newly unpacked paper? Result Yes OK Treatment
Paper
Yes
Yes
Turn off the machine in the middle of printing, and then check the toner image on the Drum. Is the toner image looks normal? Is the Transfer/Separation Corona installed to the machine correctly? Is the high voltage of Transfer Corona leaking? Is the resistance of Lead Wire about 10 kilo ohms, which connects the HV Power Supply and the Transfer Corona? Is a correct voltage inputted from the HV Power Supply to the Transfer Corona?
Yes No
1. If the paper was humidified, instruct the customer of the way store the paper. 2. If the paper was not the specified one, explain the customer that some image problem may occur in that case. Change the setting of Item No.067 (Transfer Assist Setting) in the Adjustment Mode of Service Mode, so that the Separation Lamp works for the film. Go on to the step 4. Go on to the step 8.
Transfer Corona
No Yes No
Install it correctly. Clean the Transfer Corona. Replace the Lead Wire.
Lead Wire
No
7 8
Is the Developer Unit driving normally? Is the Developer Unit firmly pressed toward the Drum? (Are Counter Rollers at both sides of the Developer Roller touching the Drum Unit?) Is the Lead Wire to supply the Developer Bias correctly connected? Is the Developer Unit supplied with the Developer Bias correctly?
No No
Readjust the input voltage making reference to [4. 3. 3 Check & Adjustment of Analog Voltage to the Transfer Corona] on the page 4-35. Or replace the HV Power Supply PCB. Check the driving mechanism. Remove the Developer Unit, and then install it to the machine correctly. Connect the Lead Wire correctly. Check the contact points of Developer Bias, and also check the HV Power Supply.
9 10
No No
7-24
K105sm7e2_EUA
7. 2. 2. 4
Density is uneven
Check the following matters with the Test Pattern No.1 and No.3. If necessary use other Test Patterns.
Cause Image Corona Checking order 1 Checking Is the Image Corona dirty? Is the height of Corona Wire different between left and right? Is the Developer Unit firmly pressed toward the Drum? (Are Counter Rollers at both sides of the Developer Roller touching the Drum Unit?) Is the Lens Array dirty Are all LED of the Eraser Lamp light properly during the print? Is the Developer Roller evenly covered with the toner? Is the toner accumulating evenly in the Developer Unit? Result Yes Yes No Treatment Clean the Image Corona, or replace the Corona Wire. Adjust the height properly. Remove the Developer Unit, and then install it to the machine correctly. Check the Developer Press Unit. Clean it. 1. Replace the Eraser Lamp. 2. Replace the PW10522 PCB. Clean the Regulation Roller. Level the machine correctly.
3 4
Yes No
Developer Unit
No No
7. 2. 2. 5
Check the following matters with the Test Pattern No.1 and No.4. If necessary use other Test Patterns.
Cause Checking order 1 Checking Try to readjust each image creation component according to [7.2.1 Basic Image Adjustment] on the page 7-20. Is the problem fixed? Is the Developer Roller insulated from the ground? Is the foggy image printed even if you print a completely white pattern? Is the Developer Unit supplied with a correct Developer Bias during the print? Result Yes OK Treatment
2 3
No Yes
Developer Bias
No
Photoconductive Drum
Have you used the Photoconductive Drum longer than its part life?
Yes
Check the Developer Roller and connector. Check the output voltage from the HV Power Supply to the Image Corona. If it is not correct, readjust it. Check the output voltage from the HV Power Supply to the Developer Unit. If it is not correct, readjust it. Or replace the HV Power Supply PCB Replace the Photoconductive Drum.
7-25
K105sm7e2_EUA
7. 2. 2. 6
Check the following matters with the Test Pattern No.1 and No.4. If necessary use other Test Patterns.
Cause Light from the outside Image Corona Developer Unit Checking order 1 2 3 Checking Is any light from the outside thrown onto the Drum? Is the Image Corona dirty? Is the Developer Roller evenly covered with the toner? Result Yes Yes No Treatment Install the outer cover correctly. Clean the Image Corona, or replace the Corona Wire. Check if the Regulation Roller is fixed at the proper position. If not, fix it at the correct position.
7. 2. 2. 7
Check the following matters with the Test Pattern No.1 and No.4. If necessary use other Test Patterns.
Cause Image Corona Checking order 1 Checking Is there something like filament on the Grid Plate, which is contacted to the Drum? Is the Image Corona dirty? Is there some foreign substance on each Corona Unit or LED Head, which is contacted to the Drum? Is there any black line or damage on the Drum, of which position corresponds with the black line on the print? Result Yes Yes Yes Yes Treatment Remove it. Clean the Image Corona, or replace the Corona Wire. Remove it. Clean the Drum making reference to [5. 5. 2 Cleaning of Photoconductive Drum]. Replace the Drum if it is damaged. (Do not forget to find the cause of damage.)
2 3
7-26
K105sm7e2_EUA
7. 2. 2. 8
Check the following matters with the Test Pattern No.1 and No.3. If necessary use other Test Patterns.
Cause Image Corona Dirt of the LED Head Transfer/Separation Corona Developer Unit Checking order 1 2 3 4 Checking Is there something like filament on the Grid Plate, which is contacted to the Drum? Can you fix the problem if you clean the LED Head? Is there any foreign substance or dirt on the Transfer/Separation Corona? Is the Developer Roller evenly covered with the toner? Is there any foreign substance or dirt around the entrance area of the Fuser Unit? Is there any damage on the Drum, which runs to the direction of Drum rotation? Result Yes Yes Yes No Treatment Remove it. OK Clean the Transfer / Separation Corona. Check whether or not there is damage or foreign substance on the Regulation Roller. Clean it off Clean the Drum making reference to [5. 5. 2 Cleaning of Photoconductive Drum]. Replace the Drum if it is damaged. (Do not forget to find the cause of damage.)
5 6
Yes Yes
7-27
K105sm7e2_EUA
7. 2. 2. 9
Void of image
Check the following matters with the Test Pattern No.1 and No.7. If necessary use other Test Patterns.
Cause Checking order 1 2 Checking Print out the Test Patter No.7 (halftone). Can you find void of image on the print? Can you fix the problem if you use a newly unpacked paper? Result Yes Yes Treatment Go to the step 2. 1. If the paper was humidified, instruct the customer of the way store the paper. 2. If the paper was not the specified one, explain the customer that some image problem may occur in that case. 1. Clean the Counter Rollers at both sides of the Developer Roller. 2. Wipe the Developer Roller with a dry cloth. 3. Replace the Developer Roller if damaged. 1. Check if there is enough toner in the Developer Unit. 2. Also select the Device Status Mode and check the Toner Sensor Signal (Signal Code: 091). It must be L when the toner is not covering the Toner Sensor. If not, replace the Toner Sensor.
Paper
Developer Unit
Does the void of image appear on the print constantly Keeping about 144mm of interval?
Yes
Yes
Photoconductive Drum
Does the void of image appear on the print constantly Keeping about 251mm of interval?
Yes
Clean Drum making reference to [5. 5. 2 Cleaning of Photoconductive Drum]. Replace Drum if damaged. Be sure to find the cause of the damage.
7. 2. 2.10
Check the following matters with the Test Pattern No.1 and No.4. If necessary use other Test Patterns.
Cause Checking order 1 Checking Try to readjust each image creation component according to [7.2.1 Basic Image Adjustment] on the page 7-20. Is the problem fixed? Are Transfer Guides of the Transfer / Separation Corona dirty with the toner? Result Yes OK Treatment
Transfer Guides
Yes
3 4 5
Is too much toner accumulating under the Developer Roller? Is the Inner Transport Unit dirty with the toner? Is the Guide Plate at the entrance of Fuser Unit dirty with the toner? Are Fuser Roller and Pressure Roller dirty with the toner?
Clean them. After that, check the distance between Transfer Guide and Drum. (It should be 0.6 to 0.7mm.) Clean the Developer Unit. Clean it, and also find where the toner came. Clean it. Clean them
7-28
K105sm7e2_EUA
7. 2. 2.11
Defective fusing
Check the following matters with the Test Pattern No.1 and No.3. If necessary use other Test Patterns.
Cause Fuser Unit Checking order 1 Checking Is the Fuser Roller properly heated up after turning on the machine? Is the type of paper selected on the UI same with that of actually installed paper? Can you fix the problem if you use a newly unpacked paper? Result No Treatment Refer to [7. 1. 2. 1 Fuser Error (E-001, E-002 & E-004)] to check the Fuser Unit. Select the correct paper type on the UI. 1. If the paper was humidified, instruct the customer of the way store the paper. 2. If the paper was not the specified one, explain the customer that some image problem may occur in that case. 1. Is there any part which is burnt? Replace that part if burnt. 2. Check if the Pressure Roller correctly pressed to the Fuser Roller. Adjust the fusing temperature correctly. Adjust the fusing pressure correctly. Adjust the fusing pressure in addition within 6.0 to 7.5mm in the nip width.
Paper
No
Yes
Does the fusing temperature specified in the Service Mode suits with the weight (gram/square meter) of paper?
Yes
No Fusing pressure (Nip) 4 Print the Test Patter No.20 with a tracing paper (36 or A0), and turn off the machine in the middle of printing. Remove the print from the machine and check the nip width. Is it 6.0 to 6.5mm? (Measure at 2 mm from the edge.) 2mm 2mm No Yes
6.0 to 6.5mm
7-29
K105sm7e2_EUA
7. 2. 2.12
Correct leading margin is 5mm (+/-2mm). Check the following matters with the Test Pattern No.1 and No.6. If necessary use other Test Patterns.
Cause Setting of Leading Registration Feed rollers Registration Clutch Checking order 1 2 3 Checking Is the Leading Registration properly adjusted in the Service Mode? Have you used the feeding rollers for very long term? Does the Registration Clutch operate correctly without slipping? Result No Yes No Treatment Adjust it properly. Replace them. Replace the Registration Clutch.
7. 2. 2.13
Jitter
Check the following matters with the Test Pattern No.1 and No.6. If necessary use other Test Patterns.
Cause Photoconductive Drum and its driving mechanism Checking order 1 Checking Does the jitter appear on the print constantly Keeping about 251mm of interval? Result Yes Treatment 1. Check if there is any damage or foreign substance on the driving gears (80T & 50T). 2. Check if there is any foreign substance between Drum and Counter Rollers of Developer Unit. If the Developer Roller is damaged, replace it. Check if there is any damage or foreign substance on the driving gears (32T, 22T & 24T) on the right side. Check if there is any damage or foreign substance on the driving gears (28T, 30T, 35T & 25T) on the left side. Check if there is any damage or foreign substance on the driving gears (25/34T & 16/30T) on the left side. Check if there is any damage or foreign substance on the driving gears (16T) on the left side.
2 3
Does the void of image appear on the print constantly Keeping about 144mm of interval? Does the jitter appear on the print constantly Keeping about 6.0mm of interval?
Yes Yes
Does the jitter appear on the print constantly Keeping about 6.4mm of interval?
Yes
Does the jitter appear on the print constantly Keeping about 8.6mm of interval? Does the jitter appear on the print constantly Keeping about 16.1mm of interval?
Yes
Yes
7-30
K105sm7e2_EUA
7. 2. 2.14
Check the following matters with the Test Pattern No.1 and No.8. If necessary use other Test Patterns.
Cause Dirt of the LED Head Installation of LED Head Checking order 1 2 Checking Is the LED Head dirty? Remove the LED Head, and then reinstall it to the machine. Is the problem fixed? Result Yes Yes No Clean it. OK Adjust the gap between LED Head and Drum by adding or removing the thin plates on the Aluminium Block at both sides of the Drum. Clean it. Treatment
Yes
7. 2. 2.15
Check the following matters with the Test Pattern No.1 and No.6. If necessary use other Test Patterns.
Cause Image Corona Transfer/Separation Corona Installation of LED Head Checking order 1 2 3 Checking Is the Image Corona dirty? Is the Transfer/Separation Corona dirty? Remove the LED Head, and then reinstall it to the machine. Is the problem fixed? Is the density of any image block different from that of other blocks? Result Yes Yes Yes Clean it. Clean it. OK Treatment
Yes
Adjust the gap between LED Head and Drum by adding or removing the Spacers on the Aluminium Block.
Yes
8mm
7-31
K105sm7e2_EUA
7. 2. 2.16
Check the following matters with the Test Pattern No.1. If necessary use other Test Patterns.
Cause Developer Press Unit Driving mechanism of Developer Unit Developer Bias Checking order 1 2 3 Checking Is the Developer Unit correctly pressed to the Drum? Does the Developer Roller rotate during the print? Is each Electrode Plate on the right of the Developer Unit surely contacted to the Electrode Plate on the machine side? Are connectors of signal cable firmly connected to the LED Head? Turn off the machine in the middle of printing, and then check the toner image on the Drum. Is there any toner image on the Drum? Is the Transfer Corona Wire broken? Is the Transfer/Separation Corona Unit correctly installed to the machine? If the high voltage leaking from the Transfer Corona? Is the connection of Lead Wire correct? Is the resistance of Lead Wire about 10 kilo ohms, which connects the HV Power Supply and the Transfer Corona? Can you fix the problem if you replace the HV Power Supply? Can you fix the problem if you replace the PW10522 PCB? Result No No No Treatment Check the Developer Press Unit. Check the driving mechanism of Process Unit. Try to install the Developer Unit so that they are contacted each other. And supply the conductive grease to the Electrode Plates. Connect them firmly. Replace the LED Head.
LED Head
No No
Transfer/Separation Corona
Yes No Yes No No
Replace it. Install it correctly. Check the Transfer / Separation Corona to find the cause for leaking. Connect it correctly. Replace the Lead Wire.
7 8
Yes Yes
OK OK
7. 2. 2.17
Completely black
Check the following matters with the Test Pattern No.1 and No.4. If necessary use other Test Patterns.
Cause Image Corona or HV Power Supply PCB Checking order 1 Checking Is the Image Corona Wire broken? Is the tension of the Corona Wire correct? Is the Corona Wire correctly stretched with the spring? Is a proper high voltage supplied to the Image Corona? Is the housing of Image Corona insulated from the ground? Can you fix the problem if you replace the PW10522 PCB? Result Yes No No No Treatment Replace it. Replace it. Check whether or not the spring is transformed. Adjust the high voltage, or replace the HV Power Supply PCB Replace the Zener PCB. OK
No Yes
PW10522 PCB
7-32
K105sm7e2_EUA
7. 2. 2.18
Crease of paper
Check the following matters with the Test Pattern No.1 and No.8. If necessary use other Test Patterns.
Cause Checking order 1 2 Checking Make a continuous printing. Can you find the crease on the 2nd or later prints? Is the type of paper selected on the UI same with that of actually installed paper? Can you fix the problem if you use a newly unpacked paper? Result Yes No Treatment Go to the following 8. Select the correct paper type on the UI. 1. If the paper was humidified, instruct the customer of the way store the paper. 2. If the paper was not the specified one, explain the customer that some image problem may occur in that case. Turn off the Dehumidify Heater. Replace it. Replace it. Replace it. Clean or replace it.
Paper
Yes
Lamp (H1) of Fuser Blower (Separation) Blower (Fuser Cooler) Fuser Entrance Guide Fusing pressure (Nip)
3 4 5 6
Is the Dehumidify Heater ON although the air is not humid. Does the Lamp light correctly? Is the Blower working properly during the print to help paper transportation? Is the Blower working properly during the print to cool down the Fuser? Is the Fuser Entrance Guide transformed? Or Is there anything on the Fuser Entrance Guide? Print the Test Patter No.20 with a tracing paper (36 or A0), and turn off the machine in the middle of printing. Remove the print from the machine and check the nip width. Is it 6.0 to 6.5mm? (Measure at 2 mm from the edge.) 2mm 2mm
Yes No No No Yes
6.0 to 6.5mm Fuser Motor speed 8 Is the paper slackened during the transportation when you make a long print? Yes Make the Fuser Motor speed faster.
7-33
K105sm7e2_EUA
7. 2. 2.19
Double image
Check the following matters with the Test Pattern No.1. If necessary use other Test Patterns.
Cause Paper Checking order 1 Checking Is the type of paper selected on the UI same with that of actually installed paper? Can you fix the problem if you use a newly unpacked paper? Result No Yes Treatment Select the correct paper type on the UI. 1. If the paper was humidified, instruct the customer of the way store the paper. 2. If the paper was not the specified one, explain the customer that some image problem may occur in that case. Replace it. Replace it. Replace it. Clean or replace it.
Lamp (H1) of Fuser Blower (Separation) Blower (Fuser Cooler) Fuser Entrance Guide Fusing pressure (Nip)
2 3 4 6
Does the Lamp light correctly? Is the Blower working properly during the print to help paper transportation? Is the Blower working properly during the print to cool down the Fuser? Is the Fuser Entrance Guide transformed? Or Is there anything on the Fuser Entrance Guide? Print the Test Patter No.20 with a tracing paper (36 or A0), and turn off the machine in the middle of printing. Remove the print from the machine and check the nip width. Is it 6.0 to 6.5mm? (Measure at 2 mm from the edge.) 2mm 2mm
No No No Yes
6.0 to 6.5mm
7-34
K105sm7e2_EUA
7. 2. 2.20
Check the following matters with the Test Pattern No.2. If necessary use other Test Patterns.
Cause Paper Developer Unit or Transfer/Separation Corona Fuser Unit Checking order 1 2 3 Checking Is the type of paper selected on the UI same with that of actually installed paper? Does the paper have dirt before it enters the Fuser Unit? Clean the Fuser Roller. Do you still have the problem even after the cleaning? Result No Yes Yes Treatment Select the correct paper type on the UI. Check the Developer Unit or Transfer/Separation Corona to find the cause. Decrease the setting value of fusing temperature (-3 to 5). OK
No
7-35
K105sm7e2_EUA
7. 3
7. 3. 1
7. 3. 1. 1
Cause Sensor
2 3
Is the USB Cable connected correctly? Can you fix the problem if you replace the Data Controller Board?
No Yes
7. 3. 1. 2
Cause
Scanner does not start scanning from the original set position
Checking order 1 2 3 4 Checking Is there any foreign substance under the Upper Unit? Does the Motor rotate? Is +24VDC supplied to the scanner? Can you fix the problem if you replace the Data Controller Board? Result Yes No No Yes Treatment Remove it. Check the Motor, and replace it if broken. Check the DC Power Supply on the printer part. Replace it if broken. OK
7. 3. 1. 3
Cause Sensor
7-36
K105sm7e2_EUA
7. 3. 1. 4
Cause
Original is mis-fed
Checking order 1 Checking Is there any foreign substance under the Upper Unit? Result Yes Treatment Remove it.
Foreign substance
7. 3. 1. 5
Cause
Foreign substance
7. 3. 1. 6
Cause USB Driver USB Cable
7-37
K105sm7e2_EUA
7. 3. 2
7. 3. 2. 1
Cause Calibration
2 3
No No
Connect it properly, or replace the cable if it is broken. 1. Check the DC Power Supply (+24V) of the printer part. Replace it if broken. 2. Replace the CIS. 3. Replace the Data Controller Board.
7. 3. 2. 2
Cause Scan Glass Calibration
3 4
Yes Yes
Clean them. OK
7. 3. 2. 3
Cause Scan Glass Calibration
3 4
Yes Yes
Clean them. OK
7-38
K105sm7e2_EUA
7. 3. 2. 4
Cause Position
7. 3. 2. 5
Cause Position
7. 3. 2. 6
Cause Scan Glass Resolution
7. 3. 2. 7
Cause Calibration
7-39
K105sm7e2_EUA
7. 4
If the cursor position in the screen does not correctly match the tapped position on the panel, the touch screen should be calibrated so that the cursor is located directly underneath your finger or a stylus. 1. Press [?] at the bottom right on the screen.
7-40
K105sm7e3_EUA
3. A password entry window will pop up. Type 8495107 and press [Enter].
5. Make sure that a wrench symbol is indicated at the top right of the screen. Press [Reset] to close UI operation window.
7-41
K105sm7e3_EUA
6. Tap Diagnostics folder twice as a double-click. Run the shortcut TouchScreen Configure Utility for touch screen calibration.
7-42
K105sm7e3_EUA
8. Press [Draw Test] to check that the touch screen correctly detects a tapped position.
NOTE
Using a stylus is recommended for easy and accurate touch screen calibration. Do not use any sharp instrument. 9. Test screen will appear.
7-43
K105sm7e3_EUA
10. Tap a certain point and check the cursor appears directly underneath a stylus. For example, suppose you tap the point shown the next figure.
The cursor will appear just underneath the tapped point in a correct condition (calibration is not necessary). Cursor matches the tap point
Cursor
Tap point
If the cursor appears an unintended position, the touch screen should be calibrated. Cursor does not match the tap point
Cursor
Tap point
7-44
K105sm7e3_EUA
13. On Calibration screen, a blinking X symbol on the bottom left can be seen. Press the X until it stops blinking with a beep.
NOTE
Press the X symbol for several seconds before the progress bar at the bottom reaches the end.
7-45
K105sm7e3_EUA
14. The X disappears and the next one will come in the following order: bottom right, top right, top left. Perform the same way for the other 3 points.
15. When all the 4 points are pressed successfully, Calibration screen disappears and the following dialog appears. Press [OK].
7-46
K105sm7e3_EUA
7-47
K105sm7e3_EUA
8. 1 Outline of Service Mode 8. 1. 1 Entering Service Mode 8. 1. 2 Selecting each Sub Mode 8. 1. 3 Cancelling the Service Mode 8. 2 Device Status Mode 8. 2. 1 Function 8. 2. 2 Indication and Operation 8. 2. 3 Device Signal List 8. 3 Information Mode 8. 3. 1 Function 8. 3. 2 Indication and Operation 8. 4 Device Operation Mode 8. 4. 1 Function 8. 4. 2 Indication and Operation 8. 5 Adjustment Mode 8. 5. 1 Function 8. 5. 2 Indication and Operation 8. 5. 3 Setting Item list 8. 5. 4 Explanation for each Setting Item 8. 5. 4. 1 Leading Registration (No. 000 & 001) 8. 5. 4. 2 Trailing Margin (No. 002 & 003) 8. 5. 4. 3 Side Margin (Left & right) (Sub Mode No. 004) 8. 5. 4. 4 LED Strobe Time for Main Pixel of each Block (No.008 to 010) 8. 5. 4. 5 LED Strobe Time for IST (Supplemental Pixel) of each Block (No.011 to 013) 8. 5. 4. 6 Horizontal Alignment of Pixels between Blocks (No.014 & 015) 8. 5. 4. 7 Cut Length 1 (length information provided) (No.016) 8. 5. 4. 8 Cut Length 2 (length information not provided) (No.017) 8. 5. 4. 9 Cut Length 3 (Compensation of a long print) (No.018) 8. 5. 4.10 Developer Bias (No.022 to 027) 8. 5. 4.11 Developer Bias compensation - 1st Drum revolution (No.028) 8. 5. 4.12 Transfer Voltage (No.029 to 034) 8. 5. 4.13 Separation Corona ON Timing (No.035) 8. 5. 4.14 Transfer Corona ON Timing (No.037) 8. 5. 4.15 Transfer Corona OFF Timing (No.038) 8. 5. 4.16 Fuser Temperature (No.039 to 044) 8. 5. 4.17 Fuser Temperature to start idling (No.045) 8. 5. 4.18 Warm Sleep Fuser Temperature (No.046) 8. 5. 4.19 Fuser Temperature Overshoot Value (No.047) 8. 5. 4.20 Fuser Temperature Control Range (No.048 & 049) 8. 5. 4.21 Reaction Time of Toner Supply Motor (No.050) 8. 5. 4.22 Toner Supply Motor ON Time (No.051)
8. 5. 4.23 8. 5. 4.24 8. 5. 4.25 8. 5. 4.26 8. 5. 4.27 8. 5. 4.28 8. 5. 4.29 8. 5. 4.30 8. 5. 4.31 8. 5. 4.32 8. 5. 4.33 8. 5. 4.34 8. 5. 4.35 8. 5. 4.36 8. 5. 4.37 8. 5. 4.38 8. 5. 4.39 8. 5. 4.40 8. 5. 4.41 8. 5. 4.42 8. 5. 4.43 8. 5. 4.44 8. 5. 4.45 8. 5. 4.46 8. 5. 4.47 8. 5. 4.48 8. 5. 4.49 8. 5. 4.50 8. 5. 4.51 8. 5. 4.52 8. 5. 4.53 8. 5. 4.54 8. 5. 4.55 8. 5. 4.56 8. 5. 4.57 8. 5. 4.58 8. 5. 4.59
Dot Enhancement Level (Dither) (No.052) Feed Clutch (CL3) OFF time applied to long print (No.053) Switch timing of Toner Supply Roller Bias (No.054) Metric or Inch (No.055) Language (No.056) Interface Communication Setting (No.057) Recognition of Roll Deck 2 (No.058) Counter Value (No.059) Maximum Length (No.060) Stacking Device setting (No.061) Operation of Fuser Roller (No.062) Operation of Central Fuser Fan (No.063 & 064) Drum Reverse Rotation Period (No.065) Operation of Separation Lamp (No.067) Automatic Adjustment of Cut Length (Long print) (No.069) Compensation of Fuser Motor Speed for roll paper (Plain paper / A3, 12 & 11) (No.070 to 075) Compensation of Fuser Motor Speed for roll paper (Tracing paper / A3, 12 & 11) (No.076 to 081) Compensation of Fuser Motor Speed for roll paper (Film / A3, 12 & 11) (No.082 to 087) Compensation of Fuser Motor Speed for roll paper (Special plain paper / A3, 12 & 11) (No.088 to 093) Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A3, 12 & 11) (No.094 to 099) Compensation of Fuser Motor Speed for roll paper (Special film / A3, 12 & 11) (No.100 to 105) Compensation of Fuser Motor Speed for roll paper (Plain paper / A2, 18 & 17) (No.106 to 111) Compensation of Fuser Motor Speed for roll paper (Tracing paper / A2, 18 & 17) (No.112 to 117) Compensation of Fuser Motor Speed for roll paper (Film / A2, 18 & 17) (No.118 to 123) Compensation of Fuser Motor Speed for roll paper (Special plain paper / A2, 18 & 17) (No.124 to 129) Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A2, 18 & 17) (No.130 to 135) Compensation of Fuser Motor Speed for roll paper (Special film / A2, 18 & 17) (No.136 to 141) Compensation of Fuser Motor Speed for roll paper (Plain paper / A1, 24 & 22) (No.142 to 147) Compensation of Fuser Motor Speed for roll paper (Tracing paper / A1, 24 & 22) (No.148 to 153) Compensation of Fuser Motor Speed for roll paper (Film / A1, 24 & 22) (No.154 to 159) Compensation of Fuser Motor Speed for roll paper (Special plain paper / A1, 24 & 22) (No.160 to 165) Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A1, 24 & 22) (No.166 to 171) Compensation of Fuser Motor Speed for roll paper (Special film / A1, 24 & 22) (No.172 to 177) Compensation of Fuser Motor Speed for roll paper (Plain paper / A0, 36 & 34) (No.178 to 183) Compensation of Fuser Motor Speed for roll paper (Tracing paper / A0, 36 & 34) (No.184 to 189) Compensation of Fuser Motor Speed for roll paper (Film / A0, 36 & 34) (No.190 to 195) Compensation of Fuser Motor Speed for roll paper (Special plain paper / A0, 36 & 34) (No.196 to 201)
8-53 8-54 8-55 8-56 8-56 8-56 8-56 8-57 8-57 8-57 8-58 8-58 8-58 8-59 8-60 8-61 8-63 8-64 8-65 8-66 8-67 8-68 8-69 8-70 8-71 8-72 8-73 8-74 8-75 8-76 8-77 8-78 8-79 8-80 8-81 8-82 8-83
8-1
K105sm8e1
8. 5. 4.60 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A0, 36 & 34) (No.202 to 207) 8. 5. 4.61 Compensation of Fuser Motor Speed for roll paper (Special film / A0, 36 & 34) (No.208 to 213) 8. 5. 4.62 Compensation of cut length (Deck 1 / 11) (No.214 to 219) 8. 5. 4.63 Compensation of cut length (Deck 1 / 12) (No.220 to 225) 8. 5. 4.64 Compensation of cut length (Deck 1 / 15) (No.226 to 231) 8. 5. 4.65 Compensation of cut length (Deck 1 / 17) (No.232 to 237) 8. 5. 4.66 Compensation of cut length (Deck 1 / 18) (No.238 to 243) 8. 5. 4.67 Compensation of cut length (Deck 1 / 22) (No.244 to 249) 8. 5. 4.68 Compensation of cut length (Deck 1 / 24) (No.250 to 255) 8. 5. 4.69 Compensation of cut length (Deck 1 / 30) (No.256 to 261) 8. 5. 4.70 Compensation of cut length (Deck 1 / 34) (No.262 to 267) 8. 5. 4.71 Compensation of cut length (Deck 1 / 36) (No.268 to 273) 8. 5. 4.72 Compensation of cut length (Deck 1 / A3) (No.274 to 279) 8. 5. 4.73 Compensation of cut length (Deck 1 / A2) (No.280 to 285) 8. 5. 4.74 Compensation of cut length (Deck 1 / A1) (No.286o 291) 8. 5. 4.75 Compensation of cut length (Deck 1 / A0) (No.292 to 297) 8. 5. 4.76 Compensation of cut length (Deck 1 / B1) (No.298 to 303) 8. 5. 4.77 Compensation of cut length (Deck 1 / 880) (No.304 to 309) 8. 5. 4.78 Main Motor Speed (No.310 to 315) 8. 5. 4.79 Fuser Motor Speed (No.316 to 321) 8. 5. 4.80 Separation Corona OFF Timing (No.322 to 327) 8. 5. 4.81 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / A3, A2, 12, 11, 18 & 17) (No.328 to 333) 8. 5. 4.82 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / A3, A2, 12, 11, 18 & 17) (No.334 to 339) 8. 5. 4.83 Compensation of Fuser Motor Speed for cut sheet paper (Film / A3, A2, 12, 11, 18 & 17) (No.340 to 345) 8. 5. 4.84 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / A3, A2, 12, 11, 18 & 17) (No.346 to 351) 8. 5. 4.85 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / A3, A2, 12, 11, 18 & 17) (No.352 to 357) 8. 5. 4.86 Compensation of Fuser Motor Speed for cut sheet paper (Special film / A3, A2, 12, 11, 18 & 17) (No.358 to 363) 8. 5. 4.87 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / A1, 24 & 22) (No.364 to 369) 8. 5. 4.88 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / A1, 24 & 22) (No.370 to 375) 8. 5. 4.89 Compensation of Fuser Motor Speed for cut sheet paper (Film / A1, 24 & 22) (No.376 to 381) 8. 5. 4.90 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / A1, 24 & 22) (No.382 to 387) 8. 5. 4.91 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / A1, 24 & 22) (No.388 to 393) 8. 5. 4.92 Compensation of Fuser Motor Speed for cut sheet paper (Special film / A1, 24 & 22) (No.394 to 399) 8. 5. 4.93 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / A0, 36 & 34) (No.400 to 405) 8. 5. 4.94 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / A0, 36 & 34) (No.406 to 411) 8. 5. 4.95 Compensation of Fuser Motor Speed for cut sheet paper (Film / A0, 36 & 34) (No.412 to 417) 8. 5. 4.96 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / A0, 36 & 34) (No.418 to 423) 8. 5. 4.97 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / A0, 36 & 34) (No.424 to 429) 8. 5. 4.98 Compensation of Fuser Motor Speed for cut sheet paper (Special film / A0, 36 & 34) (No.430 to 435)
8-86 8-87 8-88 8-88 8-89 8-89 8-90 8-90 8-91 8-91 8-92 8-92 8-93 8-93 8-94 8-94 8-95 8-95 8-96 8-96 8-96 8-97 8-98 8-99 8-100 8-101 8-102 8-103 8-104 8-105 8-106 8-107 8-108 8-109 8-110 8-111 8-112 8-113 8-114
8-2
K105sm8e1
8. 5. 4.99 Compensation of Fuser Motor Speed for roll paper (Plain paper / 30) (No.436 to 441) 8. 5. 4.100 Compensation of Fuser Motor Speed for roll paper (Tracing paper / 30) (No.442 to 447) 8. 5. 4.101 Compensation of Fuser Motor Speed for roll paper (Film / 30) (No.448 to 453) 8. 5. 4.102 Compensation of Fuser Motor Speed for roll paper (Special plain paper / 30) (No.454 to 459) 8. 5. 4.103 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / 30) (No.460 to 465) 8. 5. 4.104 Compensation of Fuser Motor Speed for roll paper (Special film / 30) (No.466 to 471) 8. 5. 4.105 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / 30) (No.472 to 477) 8. 5. 4.106 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / 30) (No.478 to 483) 8. 5. 4.107 Compensation of Fuser Motor Speed for cut sheet paper (Film / 30) (No.484 to 489) 8. 5. 4.108 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / 30) (No.490 to 495) 8. 5. 4.109 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / 30) (No.496 to 501) 8. 5. 4.110 Compensation of Fuser Motor Speed for cut sheet paper (Special film / 30) (No.502 to 507) 8. 5. 4.111 Transfer Voltage applied at 100mm from trailing edge (Plain paper / Tracing paper / Film) (No.508 to 510) 8. 5. 4.112 Transfer Voltage applied at 70mm from trailing edge (Plain paper / Tracing paper / Film) (No.511 to 513) 8. 5. 4.113 Fuser Motor Speed applied at 30mm from trailing edge (Plain paper / Tracing paper / Film) (No.514 to 516) 8. 5. 4.114 Compensation of cut length (Deck 2 / 11) (No.517 to 522) 8. 5. 4.115 Compensation of cut length (Deck 2 / 12) (No.523 to 528) 8. 5. 4.116 Compensation of cut length (Deck 2 / 15) (No.529 to 534) 8. 5. 4.117 Compensation of cut length (Deck 2 / 17) (No.535 to 540) 8. 5. 4.118 Compensation of cut length (Deck 2 / 18) (No.541 to 546) 8. 5. 4.119 Compensation of cut length (Deck 2 / 22) (No.547 to 552) 8. 5. 4.120 Compensation of cut length (Deck 2 / 24) (No.553 to 558) 8. 5. 4.121 Compensation of cut length (Deck 2 / 30) (No.559 to 564) 8. 5. 4.122 Compensation of cut length (Deck 2 / 34) (No.565 to 570) 8. 5. 4.123 Compensation of cut length (Deck 2 / 36) (No.571 to 576) 8. 5. 4.124 Compensation of cut length (Deck 2 / A3) (No.577 to 582) 8. 5. 4.125 Compensation of cut length (Deck 2 / A2) (No.583 to 588) 8. 5. 4.126 Compensation of cut length (Deck 2 / A1) (No.589 to 594) 8. 5. 4.127 Compensation of cut length (Deck 2 / A0) (No.595 to 600) 8. 5. 4.128 Compensation of cut length (Deck 2 / B1) (No.601 to 606) 8. 5. 4.129 Compensation of cut length (Deck 2 / 880) (No.607 to 612) 8. 5. 4.130 Judgement Value for Additional Cut Length for Non-standard Size Prints (No.613 to 616) 8. 5. 4.131 Additional Cut Length for Non-standard Size Prints (No.617 to 620) 8. 6 Running Mode 8. 6. 1 Function 8. 6. 2 Indication and Operation 8. 7 Jam/Error Mask Mode 8. 7. 1 Function 8. 7. 2 Indication and Operation
8-115 8-116 8-117 8-118 8-119 8-120 8-121 8-122 8-123 8-124 8-125 8-125 8-126 8-126 8-126 8-127 8-127 8-128 8-128 8-129 8-129 8-130 8-130 8-131 8-131 8-132 8-132 8-133 8-133 8-134 8-134 8-135 8-137 8-138 8-138 8-138 8-140 8-140 8-140
8-3
K105sm8e1
8. 8 Test Print Mode 8. 8. 1 Function 8. 8. 2 Indication and Operation 8. 8. 2. 1 Print Start Mode 8. 8. 2. 2 Deck Selection 8. 8. 2. 3 Paper Length 8. 8. 2. 4 Print Count 8. 8. 2. 5 Image Pattern 8. 8. 2. 6 Manual Type 8. 8. 2. 7 Manual Size 8. 8. 2. 8 Roll 1 Size 8. 8. 2. 9 Roll 1 Size Setting 8. 8. 2.10 Manual Size 8. 8. 2.11 Roll 2 Size Setting 8. 8. 2.12 Mirror 8. 8. 2.13 Nega/Posi 8. 8. 2.14 Scale 8. 9 Factory Adjustment Mode (Factory Use Only) 8. 9. 1 Function 8. 9. 2 Indication and Operation 8.10 Clear Mode 8.10. 1 Function 8.10. 2 Indication and Operation 8.10. 2. 1 RAM Clear Mode 8.10. 2. 2 Error Clear Mode 8.10. 2. 3 Jam History Clear Mode 8.10. 2. 4 Error History Clear Mode 8.10. 2. 5 Software Counter Setting Mode 8.10. 2. 6 Total Counter Setting Mode 8.11 User Mode 8.11. 1 Construction of the User Mode 8.11. 2 Selecting each sub mode 8.11. 3 Status Indication (Normal Mode) 8.11. 4 Deck Information Mode 8.11. 4. 1 Function 8.11. 4. 2 Indication and Operation 8.11. 5 Setting Mode 1 8.11. 5. 1 Function 8.11. 5. 2 Indication and Operation (1) Material setting (2) Size setting 8.11. 6 Setting Mode 2 8.11. 6. 1 Function 8.11. 6. 2 Indication and Operation (1) Selection of each Sub Mode (2) ON / OFF setting of Warm Sleep Mode (3) Timer setting of Warm Sleep Mode (4) ON / OFF setting of Cold Sleep Mode (5) Timer setting of Cold Sleep Mode (6) ON / OFF setting of Auto Power OFF (7) Timer setting of Auto Power OFF (8) Transfer Assist setting (9) Smoothing setting (10) Dot Enhancement ON/OFF setting (11) Full Image Mode setting (12) Low Temperature Mode setting 8.11. 7 Command Mode 8-4
8-143 8-143 8-143 8-145 8-145 8-146 8-147 8-147 8-149 8-149 8-150 8-150 8-151 8-151 8-152 8-152 8-153 8-154 8-154 8-154 8-156 8-156 8-156 8-158 8-158 8-159 8-159 8-160 8-161 8-162 8-162 8-162 8-163 8-164 8-164 8-164 8-166 8-166 8-166 8-166 8-168 8-170 8-170 8-170 8-170 8-172 8-173 8-174 8-175 8-176 8-177 8-178 8-179 8-180 8-181 8-182 8-183
K105sm8e1
8.11. 7. 1 Function 8.11. 7. 2 Indication and Operation 8.12 Scanner Utility 8.12. 1 Scanner Utility Installation 8.12. 1. 1 Installing USB Driver 8.12. 1. 2 Installing Scanner Utility 8.12. 2 Starting Scanner Utility 8.12. 3 Displaying Scanner Information 8.12. 4 Scanner Adjustment 8.12. 4. 1 Shading 8.12. 4. 2 Calibration 8.12. 4. 3 Feed Distance 8.12. 4. 4 Position 8.12. 5 Updating Scanner Firmware 8.13 Firmware Update(PW10522)
8-183 8-183 8-185 8-185 8-185 8-190 8-192 8-193 8-194 8-194 8-200 8-204 8-214 8-228 8-230
8-5
K105sm8e1
8. 1
8. 1. 1
1. Remove the cover from the front face of the machine to access the Sub UI.
2. Confirm that the machine is OFF. Then turn on the machine while pressing the [MENU] Key. You can unlock the key operation of Sub UI by this operation, so it becomes possible to enter the Service Mode.
P r i n t er R1 : 36 r ea dy
MENU ENTER
NOTE
It is impossible to enter the Service Mode if the key operation is locked. 3. Press and hold the [ * ] key, and then press the keys in the order as [ to enter the Service Mode. All segments on the LCD light when you enter the Service Mode. All segments light. ], [ ], [ ] and [ ]
4. Keep your finger away from the [ * ] key, and the ROM version is indicated. ROM version is indicated.
RO M Ver . 1. 6
FPG Ver . 0. 3 A
5. Then, select the necessary Sub Mode making reference to [1. 2 Selecting each Sub Mode] on the next page.
8-6
K105sm8e1
8. 1. 2
1 2 3 4 5 6 7 8 9
You can select each sub mode orderly whenever you press the [MENU] key.
( 1) I / O Mode
( 2) I n f o Mode
( 9) C l e a r Mode
( 3) Chec k Mode
( 8) Fac t o r y Mode
( 4) A d j us t
Mode
( 7) Tes t
Mode
( 5) Runn i ng Mode
8-7
K105sm8e1
8. 1. 3
Press and hold the [MENU] key, and then press the [ * ] key to cancel the Service Mode. The LCD indicates printers status after the cancellation.
P r i n t e r Ready R1 : 36 R2 : 24
NOTE
The key operation of Sub UI is automatically locked if you turn off the machine.
8-8
K105sm8e1
8. 2
8. 2. 1
It is possible to observe the status of each signal (input and output) independently.
8. 2. 2
1. Indicate (1) I/O Mode on the LCD pressing the [MENU] key.
2. Press the [ENTER] key, and you can enter the Device Status Mode. The LCD indicates signal code, signal name and signal status. Signal code Signal status
No000
I / O ( - H- )
Sw i t c h 1
Signal name
3. Pressing [ ] key or [ ] key, indicate the necessary signal code on the LCD. The LCD also indicates the signal name and its status according to the selected signal code.
8-9
K105sm8e1
8. 2. 3
Signal Code 000 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 Symbol
SCI_DATA MAN_S DOOR_OPN SEP_S HEAT_EXIT INPORT1 HEAT_DOOR SIG_IN ONLINE_LED COOL_BL_L SCI_LD SCI_CLK COOL_BLW_R SIG_OUT HEAT_BL_L HEAT_BL_H MAMTR HEAT_M HV_1ST HV_TR HV_AC BIAS_TRG BIAS_SW H1_CW_CCW PRESS_M TONER_M CLEAN_SW FEED_BL HEAT1 COOL_BL_C POWER_OFF ER2 COUNT HEAT_RY SLCT_CL FOWE_CL BACK_CL FEED_CL REGIST_CL M_LD FUMTR_LD DIS_CN HV1_LD TR_LD AC_LD
Serial Data Input Manual Feed Sensor Roll Deck Open Separation Sensor Exit Sensor Input Port 1 Heater Hatch Open Stacker Input Online LED Fuser Cooling Fan (Left) Serial LD Serial Clock Fuser Cooling Fan (Right) Stacker Output Fuser Blower (Low) Fuser Blower (High) Main Motor Fuser Motor Image Corona Transfer Corona Separation Corona Developer Bias Developer Bias Polarity Switch Fuser Motor Reversal Rotation Developer Press Motor Hopper Motor Cleaning Roller Voltage Polarity Switch Blower (BL7) Control SSR ON/OFF Signal 1 Fuser Cooling Fan (Center) Power Switch Output Separation Lamp Control Counter Fuser Relay Clutch Selection (Roll 1 or 2) Roll 1&2 Feed Clutch Roll 1&2 Back Clutch Feed Clutch Registration Clutch Main Motor Output Detection Fuser Motor Output Detection Developer Connection Detection Image Corona Output Detection Transfer Corona Output Detection Separation Corona Output Detection
Input Input Input Input Input Input Input Input Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Input Input Input Input Input Input
H : Paper detected H : Open L : Paper detected L : Paper detected Not used L : Open H : ON H : Rotate H : Rotate H : ON H : ON H : Rotate H : Rotate H : Output H : Output H : Output H : Output L : Positive Bias H : Reverse H : Rotate H : Rotate L : Positive H : Rotate H : Heater Lamp lights H : Rotate H : OFF H : Lighting H : Counting up H : ON H : Roll 1 H : ON H : ON H : ON H : ON
8-10
K105sm8e1
Signal Code 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095
Symbol BIAS_LD COUNT_OPEN IBUSY_H IPRADY_L IPREQ_L PAGEBL TEST_H I_POW_ON_A I_POW_ON_B LCD_CLK LCD_DATA LCD_EN LCD_RW LCD_RS CLEAN BIAS RESET_SIG RXD0 RXD1 RXD2 TXD0 TXD1 TXD2 MSCUTR MSCUTL MCUTL MCUTR IPRINT_L IPCUT_L REGIST_S R1_ENC_S R2_ENC_S VLC_OFF PRESS_S R1_SET_S R2_SET_S TONER_S R_EDGE
IC Port IC24 B IC24 A IC1-P10 IC1-P11 IC1-P12 IC1-P13 IC1-P14 IC1-P15 IC1-P16 IC1-P17 IC1-P20 IC1-P21 IC1-P23 IC1-P24 IC1-P22 IC1-P25 IC1-P26 IC1-P27 IC1-P32 IC1-P33 IC1-P51 IC1-P30 IC1-P31 IC1-P50 IC1-P60 IC1-P61 IC1-P63 IC1-P62 IC1-P34 IC1-P64 IC1-P65 IC1-P66 IC1-P67 IC1-PG0 IC1-PA5 IC1-PA6 IC1-PA7 AN5 IC1-PF7
Signal Name Developer Bias Output Detection Counter Connection Detection Data Output Busy Printer Ready Print Request Print Request Test Print
Input / Output Input Input Output Output Output Output Output Output Output Output Output Output Output Output Output Output Input Input Input Output Output Output Input Input Output Output Input Input Input Input Input Output Input Input Input Input Input
Status
LCD Clock LCD Data LCD Enable Data Read / Write Selection LCD Input Selection Cleaning Roller Bias Reset Signal Serial 0 Input Serial 1 Input Serial 2 Input Serial 0 Output Serial 1 Output Serial 2 Output Cutter Home Position Sensor (Right) Cutter Home Position Sensor (Left) Cutter Motor 1 Cutter Motor 2 Print Request Paper Cut Request Registration Sensor Roll 1 Encoder Roll 2 Encoder LCD Indication ON/OFF Developer Press Sensor Roll 1 Set Sensor Roll 2 Set Sensor Toner Sensor Feed Sensor
H : Output
J204-5 J204-6 J207-1 J207-2 J204-7 J204-8 J204-9 J204-10 J204-11 J204-12 J204-13
L : Staying at Home Position L : Staying at Home Position H : Rotate H : Rotate L : Requested L : Cutting H : Paper detected
H : Indicating L : Detecting H : Paper detected H : Paper detected H : Toner detected H : Paper detected
8-11
K105sm8e1
8. 3
8. 3. 1
Information Mode
Function
It is possible to monitor several kinds of information like analog data, operation time of each electric component and some other information.
8. 3. 2
1. Indicate (2) Info Mode on the LCD pressing the [MENU] key.
2. Press the [ENTER] key, and you can enter the Information Mode. The LCD indicates item number, item name and information. Item number Item name
No00 Fus e r
Temp1
150C
Information
3. Indicate the necessary item number pressing [ ] key or [ ] key, and you can check the concerning information. The following list shows the item number, item name and the concerning information. Item Number 00 Item Name (Indication) Fuser Temp 1
No00 Fus e r Temp1
Information This item indicates the temperature of the central part of Fuser Roller.
150C
01
Fuser Temp 2
No01 Fus e r Temp2
This item indicates the temperature of the right side of Fuser Roller.
140C
8-12
K105sm8e1
Item Number 02
Information This item indicates the temperature of the left side of Fuser Roller.
135C
03
Bias Vol
No03 B i as Vo l 1. 90V
This item indicates the analog output voltage for the Developer Bias.
04
Tr. Vol
No04 T r . Vo l
This item indicates the analog output voltage for the Transfer Corona.
1. 35V
05
Total Cut
No05 To t a l Cu t
This item indicates how many times the Cutter has operated totally for cutting the paper supplied from every source.
0000138
06
Roll 1 Cut
No06 Ro l l 1 Cu t 0000010
This item indicates how many times the Cutter has operated totally for cutting the paper supplied from Roll 1.
07
Roll 2 Cut
No07 Ro l l 2 Cu t 0000123
This item indicates how many times the Cutter has operated totally for cutting the paper supplied from Roll 2.
08
Others cut
No08 Ot he r s Cu t 0000005
This item indicates how many times the Cutter has operated when the machine was not on printing.
09
Total Image
No09 To t a l I mage
This item indicates how many times the printer has made printing operation totally.
0002541
8-13
K105sm8e1
Item Number 10
Information This item indicates how many times the printer has made printing operation with the Roll 1.
0001383
11
R2 Image
No11 R2 I mage
This item indicates how many times the printer has made printing operation with the Roll 2.
0001311
12
M Image
No12 M I mage 0000233
This item indicates how many times the printer has made printing operation with the cut sheet paper from Bypass Feeder.
13
R1 F Clutch
No13 R1 F C l u t c h 0000136
This item indicates how many times the Roll 1 Feed Clutch has operated up to the present.
14
R2 F Clutch
No14 R2 F C l u t c h 0003511
This item indicates how many times the Roll 2 Feed Clutch has operated up to the present.
15
R1 B Clutch
No15 R1 B C l u t c h 0002644
This item indicates how many times the Roll 1 Back Clutch has operated up to the present.
16
R2 B Clutch
No16 R2 B C l u t c h 0029877
This item indicates how many times the Roll 2 Back Clutch has operated up to the present.
17
Feed Clutch
No17 Feed C l u t c h 0007651
This item indicates how many times the Feed Clutch has operated up to the present.
8-14
K105sm8e1
Item Number 18
Information This item indicates how many times the Registration Clutch has operated up to the present.
19
Motor 1 Time
No19 Mo t o r 1 T i me 0000015mi n
This item indicates how long minutes the Main Motor has operated up to the present.
20
Motor 2 Time
No20 Mo t o r 2 T i me 0000003mi n
This item indicates how long minutes the Fuser Motor has operated up to the present.
21
LED On Time
No21 LED On T i me 0003212mi n
It indicates how long minutes the LED Head has lighted up to the present.
22
JAM Info
No22 Jam I n f o ( 01) 1007 0000385
23
Error Info
No23 E r r o r I nf o
This item indicates the record of jams. The information indicated on the second line is JAM History No., Jam Code and Counter Value (at the time of jam). The latest 20 jams can be indicated in succession whenever you press the ENTER Key. This item indicates the record of errors. The information indicated on the second line is Error History No., Error Code and Counter Value (at the time of error). The latest 20 errors can be indicated in succession whenever you press the ENTER Key.
8-15
K105sm8e1
8. 4
8. 4. 1
It is possible to operate several electrical components independently, such as motor, clutch, & fans. By this you can check whether or not the DC Controller PCB (PW10520) correctly outputs the signal to each component, and also you can check whether or not such electrical component operates correctly.
8. 4. 2
1. Indicate (3) Check Mode on the LCD pressing the [MENU] key.
2. Press the [ENTER] key, and you can enter the Device Operation Mode. The LCD indicates signal code, signal name of target item and signal status. Signal code
No00 Ou t p u t ( - L- ) Ma i n Mot o r
Signal status
8-16
K105sm8e1
3. Pressing the [ ] key or [ ] key, indicate the signal code of which target item you would like to operate. (Example : You will check the operation of Cutter Motor 1.)
No00 Ou t p u t ( - L- ) Ma i n Mot o r
No27 Ou t pu t ( - L- ) Cu t t e r Mo t o r 1
Signal Code 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17
Signal Name Main Motor Fuser Motor Fuser Rev Motor Press Motor Supply Motor Reserve Roll 1 Feed CL Roll 1 Back CL Roll 2 Feed CL Roll 2 Back CL Feed CL Reg. CL 1st Corona Tr Corona Sep Corona Bias Bias +/- Select Clean Bias
Target item Main Motor Fuser Motor Fuser Motor (Reversal rotation) Developer Press Motor Toner Supply Motor Reserved Roll 1 Feed Clutch Roll 1 Back Clutch Roll 2 Feed Clutch Roll 2 Back Clutch Feed Clutch Registration Clutch Image Corona Transfer Corona Separation Corona Developer Bias Positive/Negative selection of Developer Bias Cleaning Roller Bias
Signal Code 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Signal Name Clean +/- SW Cooler Blower (R) Tr Assist LED Heater Lamp 1 Heater Relay Heater Blower (L) Heater Blower (H) Feed Blower Counter Cutter Motor 1 Cutter Motor 2 Main Switch Cooler Blower (L) Cooler Blower (C)
Target item Positive/Negative selection of Cleaning Roller Voltage Cooling Fan (Right) Transfer Assist LED Fuser Lamp 1 Fuser Relay Fuser Blower (Low speed) Fuser Blower (High speed) Paper Feed Blower Counter Cutter Motor 1 Cutter Motor 2 Main Switch Cooling Fan (Left) Cooling Fan (Center)
4. When you press the [ENTER] key, the status of output signal changes from L to H and the selected target item operates independently.
No27 Ou t pu t ( - L- ) Cu t t e r Mo t o r 1
Press [ENTER].
No27 Ou t pu t ( - H- ) Cu t t e r Mo t o r 1
8-17
K105sm8e1
8. 5
8. 5. 1
Adjustment Mode
Function
8. 5. 2
1. Indicate (4) Adjust Mode on the LCD pressing the [MENU] key.
2. Press the [ENTER] key, and you can enter the Adjustment Mode. The LCD indicates item number, name of setting item and setting value. Item number
No000 020 [ 020 ]
Setting value
L ead Reg. ( Ro l l )
3. Pressing the [ ] key or [ ] key, indicate the Item Number of which Setting Value you will change. Please refer to [8.5.3 Setting item list] on and after the page 8-20 for the detail of each setting item. (Example : You will change Main Strobe A.)
No000 020 [ 020 ] No008 010 [ 010 ]
L ead Reg. ( Ro l l )
Ma i n St r obe A
8-18
K105sm8e2_EUA
4. Press the [ENTER] key. The setting value in the parenthesises starts flashing and it becomes possible to change it.
No008 010 [ 010 ] No008 010 [ 010 ]
Ma i n St r obe A
Ma i n St r obe A
NOTE
The LCD indicates another value that is not in the parenthesises. This is the current setting value.
No008 010 [ 010 ] Ma i n St r obe A
] key or [
] key.
No008 010 [ 013 ]
Ma i n St r obe A
Ma i n St r obe A
6. Press the [ENTER] key. New value stops flashing and it is validated.
No008 010 [ 013 ] No008 013 [ 013 ]
Ma i n St r obe A
Ma i n St r obe A
NOTE
Some Setting Items may require another way of operation. This kind of special operation is written in each explanation in [5.3 Explanation for each Setting Item].
8-19
K105sm8e2_EUA
8. 5. 3
Item No.
Setting Item
000 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057
Leading Registration (Roll paper) Leading Registration (Cut sheet paper) Trailing Margin (Roll paper) Trailing Margin (Cut sheet paper) Side Margin (Left and right) Reserved Reserved Reserved LED Strobe Time for Main Pixel (Block A) LED Strobe Time for Main Pixel (Block B) LED Strobe Time for Main Pixel (Block C) LED Strobe Time for IST (Supplemental Pixel) (Block A) LED Strobe Time for IST (Supplemental Pixel) (Block B) LED Strobe Time for IST (Supplemental Pixel) (Block C) Horizontal Alignment of Pixels between Image Blocks A & B Horizontal Alignment of Pixels between Image Blocks B & C Cut Length 1 (length information provided) Cut Length 2 (length information not provided) Cut Length 3 (Compensation of the length of a long print) Reserved Reserved Reserved Developer Bias (Plain Paper) Developer Bias (Tracing Paper) Developer Bias (Film) Developer Bias (Special Media/Plain Paper) Developer Bias (Special Media/Tracing Paper) Developer Bias (Special Media/Film) Developer Bias compensation - 1st Drum revolution Transfer Voltage (Plain Paper) Transfer Voltage (Tracing Paper) Transfer Voltage (Film) Transfer Voltage (Special Media/Plain Paper) Transfer Voltage (Special Media/Tracing Paper) Transfer Voltage (Special Media/Film) Separation Corona ON Timing Reserved Transfer Corona ON Timing Transfer Corona OFF Timing Fuser Temperature (Plain Paper) Fuser Temperature (Tracing paper) Fuser Temperature (Film) Fuser Temperature (Special Media/Plain Paper) Fuser Temperature (Special Media/Tracing Paper) Fuser Temperature (Special Media/Film) Fuser temperature to Start Idling Warm Sleep - Fuser Temperature Fuser Temperature Overshoot Value Fuser Temperature Control Range (In the print cycle) Fuser Temperature Control Range (Stand by) Reaction Time of Toner Supply Motor Toner Supply Motor Time Dot Enhancement Level ( Dither ) Feed Clutch OFF Time applied to long print Switch timing of Toner Supply Roller Bias Metric or Inch Language Interface Communication Setting
1 to 40 1 to 40 1 to 40 1 to 40 0 to 20
1 microsecond 1 microsecond 1 microsecond 1 microsecond 1 microsecond 1 microsecond 1mm 1mm 0.1mm 1mm 1mm 1mm o 1C o 1C o 1C o 1C o 1C o 1C o 1C o 1C o 1C o 1C o 1C 1 Second 1 Second 1msec. 1mm -
10 10 10 0 0 0 8 8 43 50 500
10 10 10 0 0 0 8 8 43 50 500
8-38 8-38 8-38 8-40 8-40 8-40 8-42 8-42 8-43 8-43 8-44
135 135 135 135 135 135 155 243 243 243 175 175 175 50 50 35 165 164 170 165 165 160 120 100 0 1 2 15 10 1 130 45 1 1 2
135 135 135 135 135 135 155 243 243 243 175 175 175 50 48 23 165 165 160 165 165 160 120 100 10 1 2 15 10 1 130 45 0 1 2
0 to 255 0 to 255 0 to 255 0 to 255 0 to 255 0 to 255 0 to 255 3 to 255 3 to 255 3 to 255 3 to 255 3 to 255 3 to 255 0 to 100 0 to 100 0 to 100 120 to 180 120 to 180 120 to 180 120 to 180 120 to 180 120 to 180 100 to 140 100 to 160 0 to 30 1 to 20 1 to 20 1 to 30 1 to 15 1 to 3 80 to 180 0 to 220 0 to 1 0 to 1 0 to 2
8-46 8-46 8-46 8-46 8-46 8-46 8-47 8-47 8-47 8-47 8-47 8-47 8-47 8-48 8-48 8-49 8-50 8-50 8-50 8-50 8-50 8-50 8-51 8-51 8-52 8-53 8-53 8-54 8-54 8-55 8-56 8-57 8-58 8-58 8-58
8-20
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 1 1 5 0 0 0 0 0 0 0 167 168 143 143 50 50 4 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 4 Setting range Refer to page ;
058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093
Recognition of Roll Deck 2 Counter Value Maximum Length Stacking Device Setting Operation of Fuser Roller Operation of Central Fuser Fan (Tracing paper) Operation of Central Fuser Fan (Special tracing paper) Drum ReverseTime Reserved Operation of Separation Lamp Reserved Automatic Adjustment of Cut Length Fuser Motor 1st Speed (Roll) (Plain Paper / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll) (Plain Paper / A3, 12 & 11) Fuser Motor 2nd Speed (Roll) (Plain Paper / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll) (Plain Paper / A3, 12 & 11) Fuser Motor 3rd Speed (Roll) (Plain Paper / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll) (Plain Paper / A3, 12 & 11) Fuser Motor 1st Speed (Roll) (Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll) (Tracing / A3, 12 & 11) Fuser Motor 2nd Speed (Roll) (Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll) (Tracing / A3, 12 & 11) Fuser Motor 3rd Speed (Roll) (Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll) (Tracing / A3, 12 & 11) Fuser Motor 1st Speed (Roll) (Film / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll) (Film / A3, 12 & 11) Fuser Motor 2nd Speed (Roll) (Film / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll) (Film / A3, 12 & 11) Fuser Motor 3rd Speed (Roll) (Film / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll) (Film / A3, 12 & 11) Fuser Motor 1st Speed (Roll) (Special Media / Plain Paper / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Plain Paper / A3, 12 & 11) Fuser Motor 2nd Speed Setting (Roll) (Special Media / Plain Paper / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Plain Paper / A3, 12 & 11) Fuser Motor 3rd Speed (Roll) (Special Media / Plain Paper / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Plain Paper / A3, 12 & 11)
1C o 1C 1 millisecond
0 to 1 0 to 5 0 to 1 0 to 1 0 to 1 130 to 170 130 to 170 10 to 70 1 to 7 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-58 8-59 8-59 8-59 8-60 8-60 8-60 8-60 8-61 8-62 8-63 8-63 8-63 8-63 8-63 8-63 8-65 8-65 8-65 8-65 8-65 8-65 8-66 8-66 8-66 8-66 8-66 8-66 8-67 8-67 8-67 8-67 8-67 8-67
25 1 27 2 20 2 23 1 23 2 23 3 25 1 25 2 20 0 20 0 20 0 20 0
23 1 25 2 21 2 23 1 23 2 23 3 22 1 22 2 20 0 20 0 20 0 20 0
8-21
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 20 20 0 20 0 20 0 20 0 20 0 20 0 23 1 24 3 23 5 23 1 24 3 24 3 25 1 25 3 20 0 0 20 0 20 0 20 0 20 0 20 0 22 1 24 3 22 5 23 1 24 3 24 3 22 1 22 3 20 0 Setting range Refer to page ;
094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123
Fuser Motor 1st Speed (Roll) (Special Media / Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Tracing / A3, 12 & 11) Fuser Motor 2nd Speed (Roll) (Special Media / Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Tracing / A3, 12 & 11) Fuser Motor 3rd Speed (Roll) (Special Media / Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Tracing / A3, 12 & 11) Fuser Motor 1st Speed (Roll) (Special Media / Film / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Film / A3, 12 & 11) Fuser Motor 2nd Speed (Roll) (Special Media / Film / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Film / A3, 12 & 11) Fuser Motor 3rd Speed (Roll) (Special Media / Film / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Film / A3, 12 & 11) Fuser Motor 1st Speed (Roll) (Plain Paper / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll) (Plain Paper / A2, 18 & 17) Fuser Motor 2nd Speed (Roll) (Plain Paper / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll) (Plain Paper / A2, 18 & 17) Fuser Motor 3rd Speed (Roll) (Plain Paper / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll) (Plain Paper / A2, 18 & 17) Fuser Motor 1st Speed (Roll) (Tracing / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll) (Tracing / A2, 18 & 17) Fuser Motor 2nd Speed (Roll) (Tracing / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll) (Tracing / A2, 18 & 17) Fuser Motor 3rd Speed (Roll) (Tracing / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll) (Tracing / A2, 18 & 17) Fuser Motor 1st Speed (Roll) (Film / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll) (Film / A2, 18 & 17) Fuser Motor 2nd Speed (Roll) (Film / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll) (Film / A2, 18 & 17) Fuser Motor 3rd Speed (Roll) (Film / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll) (Film / A2, 18 & 17)
1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second
0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-68 8-68 8-68 8-68 8-68 8-68 8-69 8-69 8-69 8-69 8-69 8-69 8-70 8-70 8-70 8-70 8-70 8-70 8-71 8-71 8-71 8-71 8-71 8-71 8-72 8-72 8-72 8-72 8-72 8-72
8-22
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 20 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 22 1 21 7 21 8 22 1 23 7 22 5 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 21 1 22 7 21 8 22 1 24 7 23 5 Setting range Refer to page ;
124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153
Fuser Motor 1st Speed (Roll) (Special Media / Plain Paper / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Plain Paper / A2, 18 & 17) Fuser Motor 2nd Speed (Roll) (Special Media / Plain Paper / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Plain Paper / A2, 18 & 17) Fuser Motor 3rd Speed (Roll) (Special Media / Plain Paper / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Plain Paper / A2, 18 & 17) Fuser Motor 1st Speed (Roll) (Special Media / Tracing / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Tracing / A2, 18 & 17) Fuser Motor 2nd Speed (Roll) (Special Media / Tracing / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Tracing / A2, 18 & 17) Fuser Motor 3rd Speed (Roll) (Special Media / Tracing / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Tracing / A2, 18 & 17) Fuser Motor 1st Speed (Roll) (Special Media / Film / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Film / A2, 18 & 17) Fuser Motor 2nd Speed (Roll) (Special Media / Film / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Film / A2, 18 & 17) Fuser Motor 3rd Speed (Roll) (Special Media / Film / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Film / A2, 18 & 17) Fuser Motor 1st Speed (Roll) (Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll) (Plain Paper / A1, 24 & 22) Fuser Motor 2nd Speed (Roll) (Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll) (Plain Paper / A1, 24 & 22) Fuser Motor 3rd Speed (Roll) (Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll) (Plain Paper / A1, 24 & 22) Fuser Motor 1st Speed (Roll) (Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll) (Tracing / A1, 24 & 22) Fuser Motor 2nd Speed (Roll) (Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll) (Tracing / A1, 24 & 22) Fuser Motor 3rd Speed (Roll) (Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll) (Tracing / A1, 24 & 22)
1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second
0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-73 8-73 8-73 8-73 8-73 8-73 8-74 8-74 8-74 8-74 8-74 8-74 8-75 8-75 8-75 8-75 8-75 8-75 8-76 8-76 8-76 8-76 8-76 8-76 8-77 8-77 8-77 8-77 8-77 8-77
8-23
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 21 21 1 21 7 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 19 1 19 12 20 11 1 21 7 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 18 1 19 12 18 11 Setting range Refer to page ;
154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183
Fuser Motor 1st Speed (Roll) (Film / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll) (Film / A1, 24 & 22) Fuser Motor 2nd Speed (Roll) (Film / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll) (Film / A1, 24 & 22) Fuser Motor 3rd Speed (Roll) (Film / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll) (Film / A1, 24 & 22) Fuser Motor 1st Speed (Roll) (Special Media / Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Plain Paper / A1, 24 & 22) Fuser Motor 2nd Speed (Roll) (Special Media / Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Plain Paper / A1, 24 & 22) Fuser Motor 3rd Speed (Roll) (Special Media / Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Plain Paper / A1, 24 & 22) Fuser Motor 1st Speed (Roll) (Special Media / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Tracing / A1, 24 & 22) Fuser Motor 2nd Speed (Roll) (Special Media / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Tracing / A1, 24 & 22) Fuser Motor 3rd Speed (Roll) (Special Media / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Tracing / A1, 24 & 22) Fuser Motor 1st Speed (Roll) (Special Media / Film / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Film / A1, 24 & 22) Fuser Motor 2nd Speed (Roll) (Special Media / Film / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Film / A1, 24 & 22) Fuser Motor 3rd Speed (Roll) (Special Media / Film / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Film / A1, 24 & 22) Fuser Motor 1st Speed (Roll) (Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll) (Plain Paper / A0, 36 & 34) Fuser Motor 2nd Speed (Roll) (Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll) (Plain Paper / A0, 36 & 34) Fuser Motor 3rd Speed (Roll) (Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll) (Plain Paper / A0, 36 & 34)
1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second
0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-78 8-78 8-78 8-78 8-78 8-78 8-79 8-79 8-79 8-79 8-79 8-79 8-80 8-80 8-80 8-80 8-80 8-80 8-81 8-81 8-81 8-81 8-81 8-81 8-82 8-82 8-82 8-82 8-82 8-82
8-24
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 19 20 1 20 12 20 5 22 1 25 12 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 1 21 12 19 5 20 1 23 12 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 Setting range Refer to page ;
184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213
Fuser Motor 1st Speed (Roll) (Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll) (Tracing / A0, 36 & 34) Fuser Motor 2nd Speed (Roll) (Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll) (Tracing / A0, 36 & 34) Fuser Motor 3rd Speed (Roll) (Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll) (Tracing / A0, 36 & 34) Fuser Motor 1st Speed (Roll) (Film / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll) (Film / A0, 36 & 34) Fuser Motor 2nd Speed (Roll) (Film / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll) (Film / A0, 36 & 34) Fuser Motor 3rd Speed (Roll) (Film / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll) (Film / A0, 36 & 34) Fuser Motor 1st Speed (Roll) (Special Media / Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Plain Paper / A0, 36 & 34) Fuser Motor 2nd Speed (Roll) (Special Media / Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Plain Paper / A0, 36 & 34) Fuser Motor 3rd Speed (Roll) (Special Media / Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Plain Paper / A0, 36 & 34) Fuser Motor 1st Speed (Roll) (Special Media / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Tracing / A0, 36 & 34) Fuser Motor 2nd Speed (Roll) (Special Media / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Tracing / A0, 36 & 34) Fuser Motor 3rd Speed (Roll) (Special Media / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Tracing / A0, 36 & 34) Fuser Motor 1st Speed (Roll) (Special Media / Film / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Film / A0, 36 & 34) Fuser Motor 2nd Speed (Roll) (Special Media / Film / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Film / A0, 36 & 34) Fuser Motor 3rd Speed (Roll) (Special Media / Film / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Film / A0, 36 & 34)
1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second
0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-83 8-83 8-83 8-83 8-83 8-83 8-84 8-84 8-84 8-84 8-84 8-84 8-85 8-85 8-85 8-85 8-85 8-85 8-86 8-86 8-86 8-86 8-86 8-86 8-87 8-87 8-87 8-87 8-87 8-87
8-25
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 54 54 50 50 50 50 50 50 Setting range Refer to page ;
214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273
Deck 1 Compensation of cut length (11 / Plain paper) Deck 1 Compensation of cut length (11 / Tracing paper) Deck 1 Compensation of cut length (11 / Film) Deck 1 Compensation of cut length (11 / Special plain paper) Deck 1 Compensation of cut length (11 / Special tracing paper) Deck 1 Compensation of cut length (11 / Special film) Deck 1 Compensation of cut length (12 / Plain paper) Deck 1 Compensation of cut length (12 / Tracing paper) Deck 1 Compensation of cut length (12 / Film) Deck 1 Compensation of cut length (12 / Special plain paper) Deck 1 Compensation of cut length (12 / Special tracing paper) Deck 1 Compensation of cut length (12 / Special film) Deck 1 Compensation of cut length (15 / Plain paper) Deck 1 Compensation of cut length (15 / Tracing paper) Deck 1 Compensation of cut length (15 / Film) Deck 1 Compensation of cut length (15 / Special plain paper) Deck 1 Compensation of cut length (15 / Special tracing paper) Deck 1 Compensation of cut length (15 / Special film) Deck 1 Compensation of cut length (17 / Plain paper) Deck 1 Compensation of cut length (17 / Tracing paper) Deck 1 Compensation of cut length (17 / Film) Deck 1 Compensation of cut length (17 / Special plain paper) Deck 1 Compensation of cut length (17 / Special tracing paper) Deck 1 Compensation of cut length (17 / Special film) Deck 1 Compensation of cut length (18 / Plain paper) Deck 1 Compensation of cut length (18 / Tracing paper) Deck 1 Compensation of cut length (18 / Film) Deck 1 Compensation of cut length (18 / Special plain paper) Deck 1 Compensation of cut length (18 / Special tracing paper) Deck 1 Compensation of cut length (18 / Special film) Deck 1 Compensation of cut length (22 / Plain paper) Deck 1 Compensation of cut length (22 / Tracing paper) Deck 1 Compensation of cut length (22 / Film) Deck 1 Compensation of cut length (22 / Special plain paper) Deck 1 Compensation of cut length (22 / Special tracing paper) Deck 1 Compensation of cut length (22 / Special film) Deck 1 Compensation of cut length (24 / Plain paper) Deck 1 Compensation of cut length (24 / Tracing paper) Deck 1 Compensation of cut length (24 / Film) Deck 1 Compensation of cut length (24 / Special plain paper) Deck 1 Compensation of cut length (24 / Special tracing paper) Deck 1 Compensation of cut length (24 / Special film) Deck 1 Compensation of cut length (30 / Plain paper) Deck 1 Compensation of cut length (30 / Tracing paper) Deck 1 Compensation of cut length (30 / Film) Deck 1 Compensation of cut length (30 / Special plain paper) Deck 1 Compensation of cut length (30 / Special tracing paper) Deck 1 Compensation of cut length (30 / Special film) Deck 1 Compensation of cut length (34 / Plain paper) Deck 1 Compensation of cut length (34 / Tracing paper) Deck 1 Compensation of cut length (34 / Film) Deck 1 Compensation of cut length (34 / Special plain paper) Deck 1 Compensation of cut length (34 / Special tracing paper) Deck 1 Compensation of cut length (34 / Special film) Deck 1 Compensation of cut length (36 / Plain paper) Deck 1 Compensation of cut length (36 / Tracing paper) Deck 1 Compensation of cut length (36 / Film) Deck 1 Compensation of cut length (36 / Special plain paper) Deck 1 Compensation of cut length (36 / Special tracing paper) Deck 1 Compensation of cut length (36 / Special film)
0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100
8-88 8-88 8-88 8-88 8-88 8-88 8-88 8-88 8-88 8-88 8-88 8-88 8-89 8-89 8-89 8-89 8-89 8-89 8-89 8-89 8-89 8-89 8-89 8-89 8-90 8-90 8-90 8-90 8-90 8-90 8-90 8-90 8-90 8-90 8-90 8-90 8-91 8-91 8-91 8-91 8-91 8-91 8-91 8-91 8-91 8-91 8-91 8-91 8-91 8-92 8-92 8-92 8-92 8-92 8-92 8-92 8-92 8-92 8-92 8-92
8-26
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 52 50 50 50 50 50 50 50 50 50 50 50 54 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 21 21 21 21 24 21 20 20 20 20 20 20 25 18 24 31 25 24 20 20 20 20 20 20 45 45 45 45 22 22 58 58 58 58 58 58 23 22 1 24 3 23 5 1 24 3 22 5 Setting range Refer to page ;
274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333
Deck 1 Compensation of cut length (A3 / Plain paper) Deck 1 Compensation of cut length (A3 / Tracing paper) Deck 1 Compensation of cut length (A3 / Film) Deck 1 Compensation of cut length (A3 / Special plain paper) Deck 1 Compensation of cut length (A3 / Special tracing paper) Deck 1 Compensation of cut length (A3 / Special film) Deck 1 Compensation of cut length (A2 / Plain paper) Deck 1 Compensation of cut length (A2 / Tracing paper) Deck 1 Compensation of cut length (A2 / Film) Deck 1 Compensation of cut length (A2 / Special plain paper) Deck 1 Compensation of cut length (A2 / Special tracing paper) Deck 1 Compensation of cut length (A2 / Special film) Deck 1 Compensation of cut length (A1 / Plain paper) Deck 1 Compensation of cut length (A1 / Tracing paper) Deck 1 Compensation of cut length (A1 / Film) Deck 1 Compensation of cut length (A1 / Special plain paper) Deck 1 Compensation of cut length (A1 / Special tracing paper) Deck 1 Compensation of cut length (A1 / Special film) Deck 1 Compensation of cut length (A0 / Plain paper) Deck 1 Compensation of cut length (A0 / Tracing paper) Deck 1 Compensation of cut length (A0 / Film) Deck 1 Compensation of cut length (A0 / Special plain paper) Deck 1 Compensation of cut length (A0 / Special tracing paper) Deck 1 Compensation of cut length (A0 / Special film) Deck 1 Compensation of cut length (B1 / Plain paper) Deck 1 Compensation of cut length (B1 / Tracing paper) Deck 1 Compensation of cut length (B1 / Film) Deck 1 Compensation of cut length (B1 / Special plain paper) Deck 1 Compensation of cut length (B1 / Special tracing paper) Deck 1 Compensation of cut length (B1 / Special film) Deck 1 Compensation of cut length (880 / Plain paper) Deck 1 Compensation of cut length (880 / Tracing paper) Deck 1 Compensation of cut length (880 / Film) Deck 1 Compensation of cut length (880 / Special plain paper) Deck 1 Compensation of cut length (880 / Special tracing paper) Deck 1 Compensation of cut length (880 / Special film) Main Motor Speed (Plain paper) Main Motor Speed (Tracing paper) Main Motor Speed (Film) Main Motor Speed (Special plain paper) Main Motor Speed (Special tracing paper) Main Motor Speed (Special film) Fuser Motor Speed (Plain paper) Fuser Motor Speed (Tracing paper) Fuser Motor Speed (Film paper) Fuser Motor Speed (Special plain paper) Fuser Motor Speed (Special tracing paper) Fuser Motor Speed (Special film) Separation Corona OFF Timing (Plain paper) Separation Corona OFF Timing (tracing paper) Separation Corona OFF Timing (Film) Separation Corona OFF Timing (Special plain paper) Separation Corona OFF Timing (Special tracing paper) Separation Corona OFF Timing (Special film) Fuser Motor 1st Speed (Cut sheet) (Plain Paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Plain Paper / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet) (Plain Paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Plain Paper / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet) (Plain Paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Plain Paper / A3, A2, 12, 11, 18 & 17)
0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 40 0 to 40 0 to 40 0 to 40 0 to 40 0 to 40 0 to 40 0 to 40 0 to 40 0 to 40 0 to 40 0 to 40 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-93 8-93 8-93 8-93 8-93 8-93 8-93 8-93 8-93 8-93 8-93 8-93 8-94 8-94 8-94 8-94 8-94 8-94 8-94 8-94 8-94 8-94 8-94 8-94 8-95 8-95 8-95 8-95 8-95 8-95 8-95 8-95 8-95 8-95 8-95 8-95 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-96 8-97 8-97 8-97 8-97 8-97 8-97
8-27
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 23 23 1 24 3 24 3 25 1 25 3 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 22 1 21 7 21 8 1 24 3 24 3 22 1 22 3 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 21 1 22 7 21 8 Setting range Refer to page ;
334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369
Fuser Motor 1st Speed (Roll) (Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Tracing / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet) (Tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Tracing / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet) (Tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Tracing / A3, A2, 12, 11, 18 & 17) Fuser Motor 1st Speed (Cut sheet) (Film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Film / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet) (Film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Film / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet) (Film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Film / A3, A2, 12, 11, 18 & 17) Fuser Motor 1st Speed (Cut sheet) (Special Media / Plain Paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Plain Paper / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Plain Paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Plain Paper / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Plain Paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Plain Paper / A3, A2, 12, 11, 18 & 17) Fuser Motor 1st Speed (Cut sheet) (Special Media / Tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Tracing / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Tracing / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Tracing / A3, A2, 12, 11, 18 & 17) Fuser Motor 1st Speed (Cut sheet) (Special Media / Film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Film / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Film / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Film / A3, A2, 12, 11, 18 & 17) Fuser Motor 1st Speed (Cut sheet) (Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Plain Paper / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet) (Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Plain Paper / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet) (Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Plain Paper / A1, 24 & 22)
1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second
0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-98 8-98 8-98 8-98 8-98 8-98 8-99 8-99 8-99 8-99 8-99 8-99 8-100 8-100 8-100 8-100 8-100 8-100 8-101 8-101 8-101 8-101 8-101 8-101 8-102 8-102 8-102 8-102 8-102 8-102 8-103 8-103 8-103 8-103 8-103 8-103
8-28
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 22 22 1 23 7 22 5 21 1 21 7 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 1 24 7 23 5 21 1 21 7 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 Setting range Refer to page ;
370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399
Fuser Motor 1st Speed (Cut sheet) (Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Tracing / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet) (Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Tracing / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet) (Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Tracing / A1, 24 & 22) Fuser Motor 1st Speed (Cut sheet) (Film / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Film / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet) (Film / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Film / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet) (Film / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Film / A1, 24 & 22) Fuser Motor 1st Speed (Cut sheet) (Special Media / Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Plain Paper / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Plain Paper / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Plain Paper / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Plain Paper / A1, 24 & 22) Fuser Motor 1st Speed (Cut sheet) (Special Media / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Tracing / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Tracing / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Tracing / A1, 24 & 22) Fuser Motor 1st Speed (Cut sheet) (Special Media / Film / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Film / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Film / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Film / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Film / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Film / A1, 24 & 22)
1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second
0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-104 8-104 8-104 8-104 8-104 8-104 8-105 8-105 8-105 8-105 8-105 8-105 8-106 8-106 8-106 8-106 8-106 8-106 8-107 8-107 8-107 8-107 8-107 8-107 8-108 8-108 8-108 8-108 8-108 8-108
8-29
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 18 18 1 19 12 18 11 19 1 19 12 18 5 22 1 25 12 20 0 20 0 20 0 20 0 20 0 20 0 20 0 1 19 12 18 11 20 1 21 12 19 5 20 1 23 12 20 0 20 0 20 0 20 0 20 0 20 0 20 0 Setting range Refer to page ;
400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429
Fuser Motor 1st Speed (Cut sheet) (Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Plain Paper / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet) (Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Plain Paper / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet) (Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Plain Paper / A0, 36 & 34) Fuser Motor 1st Speed (Cut sheet) (Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Tracing / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet) (Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Tracing / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet) (Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Tracing / A0, 36 & 34) Fuser Motor 1st Speed (Cut sheet) (Film / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Film / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet) (Film / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Film / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet) (Film / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Film / A0, 36 & 34) Fuser Motor 1st Speed (Cut sheet) (Special Media / Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Plain Paper / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Plain Paper / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Plain Paper / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Plain Paper / A0, 36 & 34) Fuser Motor 1st Speed (Cut sheet) (Special Media / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Tracing / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Tracing / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Tracing / A0, 36 & 34)
1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second
0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-109 8-109 8-109 8-109 8-109 8-109 8-110 8-110 8-110 8-110 8-110 8-110 8-111 8-111 8-111 8-111 8-111 8-111 8-112 8-112 8-112 8-112 8-112 8-112 8-113 8-113 8-113 8-113 8-113 8-113
8-30
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 20 20 0 20 0 20 0 21 1 20 12 22 11 22 1 21 12 23 5 22 1 25 12 20 0 20 0 20 0 20 0 0 20 0 20 0 20 1 20 12 20 11 23 1 22 12 21 5 20 1 23 12 20 0 20 0 20 0 20 0 Setting range Refer to page ;
430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459
Fuser Motor 1st Speed (Cut sheet) (Special Media / Film / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Film / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Film / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Film / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Film / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Film / A0, 36 & 34) Fuser Motor 1st Speed (Roll) (Plain Paper / 30) Switch Timing to Fuser Motor 1st Speed (Roll) (Plain Paper / 30) Fuser Motor 2nd Speed (Roll) (Plain Paper / 30) Switch Timing to Fuser Motor 2nd Speed (Roll) (Plain Paper / 30) Fuser Motor 3rd Speed (Roll) (Plain Paper / 30) Switch Timing to Fuser Motor 3rd Speed (Roll) (Plain Paper / 30) Fuser Motor 1st Speed (Roll) (Tracing / 30) Switch Timing to Fuser Motor 1st Speed (Roll) (Tracing / 30) Fuser Motor 2nd Speed (Roll) (Tracing / 30) Switch Timing to Fuser Motor 2nd Speed (Roll) (Tracing / 30) Fuser Motor 3rd Speed (Roll) (Tracing / 30) Switch Timing to Fuser Motor 3rd Speed (Roll) (Tracing / 30) Fuser Motor 1st Speed (Roll) (Film / 30) Switch Timing to Fuser Motor 1st Speed (Roll) (Film / 30) Fuser Motor 2nd Speed (Roll) (Film / 30) Switch Timing to Fuser Motor 2nd Speed (Roll) (Film / 30) Fuser Motor 3rd Speed (Roll) (Film / 30) Switch Timing to Fuser Motor 3rd Speed (Roll) (Film / 30) Fuser Motor 1st Speed (Roll) (Special Media / Plain Paper / 30) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Plain Paper / 30) Fuser Motor 2nd Speed (Roll) (Special Media / Plain Paper / 30) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Plain Paper / 30) Fuser Motor 3rd Speed (Roll) (Special Media / Plain Paper / 30) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Plain Paper / 30)
1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second
0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-114 8-114 8-114 8-114 8-114 8-114 8-115 8-115 8-115 8-115 8-115 8-115 8-116 8-116 8-116 8-116 8-116 8-116 8-117 8-117 8-117 8-117 8-117 8-117 8-118 8-118 8-118 8-118 8-118 8-118
8-31
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 20 20 0 20 0 20 0 20 0 20 0 20 0 20 1 20 12 20 11 22 1 20 12 21 5 22 1 25 12 20 0 0 20 0 20 0 20 0 20 0 20 0 18 1 19 12 18 11 20 1 21 12 19 5 20 1 23 12 20 0 Setting range Refer to page ;
460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489
Fuser Motor 1st Speed (Roll) (Special Media / Tracing / 30) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Tracing / 30) Fuser Motor 2nd Speed (Roll) (Special Media / Tracing / 30) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Tracing / 30) Fuser Motor 3rd Speed (Roll) (Special Media / Tracing / 30) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Tracing / 30) Fuser Motor 1st Speed (Roll) (Special Media / Film / 30) Switch Timing to Fuser Motor 1st Speed (Roll) (Special Media / Film / 30) Fuser Motor 2nd Speed (Roll) (Special Media / Film / 30) Switch Timing to Fuser Motor 2nd Speed (Roll) (Special Media / Film / 30) Fuser Motor 3rd Speed (Roll) (Special Media / Film / 30) Switch Timing to Fuser Motor 3rd Speed (Roll) (Special Media / Film / 30) Fuser Motor 1st Speed (Cut sheet) (Plain Paper / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Plain Paper / 30) Fuser Motor 2nd Speed (Cut sheet) (Plain Paper / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Plain Paper / 30) Fuser Motor 3rd Speed (Cut sheet) (Plain Paper / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Plain Paper / 30) Fuser Motor 1st Speed (Cut sheet) (Tracing / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Tracing / 30) Fuser Motor 2nd Speed (Cut sheet) (Tracing / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Tracing / 30) Fuser Motor 3rd Speed (Cut sheet) (Tracing / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Tracing / 30) Fuser Motor 1st Speed (Cut sheet) (Film / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Roll) (Film / 30) Fuser Motor 2nd Speed (Roll) (Cut sheet) (Film / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Film / 30) Fuser Motor 3rd Speed (Cut sheet) (Film / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Film / 30)
1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second 1 second
0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400
8-119 8-119 8-119 8-119 8-119 8-119 8-120 8-120 8-120 8-120 8-120 8-120 8-121 8-121 8-121 8-121 8-121 8-121 8-122 8-122 8-122 8-122 8-122 8-122 8-123 8-123 8-123 8-123 8-123 8-123
8-32
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 20 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 255 255 255 33 33 255 16 16 0 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 20 0 255 255 255 33 33 255 16 16 0 Setting range Refer to page ;
490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516
Fuser Motor 1st Speed (Cut sheet) (Special Media / Plain Paper / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Plain Paper / 30) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Plain Paper / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Plain Paper / 30) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Plain Paper / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Plain Paper / 30) Fuser Motor 1st Speed (Cut sheet) (Special Media / Tracing / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Tracing / 30) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Tracing / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Tracing / 30) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Tracing / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Tracing / 30) Fuser Motor 1st Speed (Cut sheet) (Special Media / Film / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet) (Special Media / Film / 30) Fuser Motor 2nd Speed (Cut sheet) (Special Media / Film / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet) (Special Media / Film / 30) Fuser Motor 3rd Speed (Cut sheet) (Special Media / Film / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet) (Special Media / Film / 30) Transfer Voltage applied at 100mm from trailing edge (Plain paper) Transfer Voltage applied at 100mm from trailing edge (Tracing paper) Transfer Voltage applied at 100mm from trailing edge (Film) Transfer Voltage applied at 70mm from trailing edge (Plain paper) Transfer Voltage applied at 70mm from trailing edge (Tracing paper) Transfer Voltage applied at 70mm from trailing edge (Film) Fuser Motor Speed applied at 30mm from trailing edge (Plain paper) Fuser Motor Speed applied at 30mm from trailing edge (Tracing paper) Fuser Motor Speed applied at 30mm from trailing edge (Film)
0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 0 to 510 0 to 510 0 to 510 0 to 40 0 to 40 0 to 40
8-124 8-124 8-124 8-124 8-124 8-124 8-125 8-125 8-125 8-125 8-125 8-125 8-125 8-125 8-125 8-125 8-125 8-125 8-126 8-126 8-126 8-126 8-126 8-126 8-126 8-126 8-126
8-33
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 54 54 50 50 50 50 50 50 Setting range Refer to page ;
517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576
Deck 2 Compensation of cut length (11 / Plain paper) Deck 2 Compensation of cut length (11 / Tracing paper) Deck 2 Compensation of cut length (11 / Film) Deck 2 Compensation of cut length (11 / Special plain paper) Deck 2 Compensation of cut length (11 / Special tracing paper) Deck 2 Compensation of cut length (11 / Special film) Deck 2 Compensation of cut length (12 / Plain paper) Deck 2 Compensation of cut length (12 / Tracing paper) Deck 2 Compensation of cut length (12 / Film) Deck 2 Compensation of cut length (12 / Special plain paper) Deck 2 Compensation of cut length (12 / Special tracing paper) Deck 2 Compensation of cut length (12 / Special film) Deck 2 Compensation of cut length (15 / Plain paper) Deck 2 Compensation of cut length (15 / Tracing paper) Deck 2 Compensation of cut length (15 / Film) Deck 2 Compensation of cut length (15 / Special plain paper) Deck 2 Compensation of cut length (15 / Special tracing paper) Deck 2 Compensation of cut length (15 / Special film) Deck 2 Compensation of cut length (17 / Plain paper) Deck 2 Compensation of cut length (17 / Tracing paper) Deck 2 Compensation of cut length (17 / Film) Deck 2 Compensation of cut length (17 / Special plain paper) Deck 2 Compensation of cut length (17 / Special tracing paper) Deck 2 Compensation of cut length (17 / Special film) Deck 2 Compensation of cut length (18 / Plain paper) Deck 2 Compensation of cut length (18 / Tracing paper) Deck 2 Compensation of cut length (18 / Film) Deck 2 Compensation of cut length (18 / Special plain paper) Deck 2 Compensation of cut length (18 / Special tracing paper) Deck 2 Compensation of cut length (18 / Special film) Deck 2 Compensation of cut length (22 / Plain paper) Deck 2 Compensation of cut length (22 / Tracing paper) Deck 2 Compensation of cut length (22 / Film) Deck 2 Compensation of cut length (22 / Special plain paper) Deck 2 Compensation of cut length (22 / Special tracing paper) Deck 2 Compensation of cut length (22 / Special film) Deck 2 Compensation of cut length (24 / Plain paper) Deck 2 Compensation of cut length (24 / Tracing paper) Deck 2 Compensation of cut length (24 / Film) Deck 2 Compensation of cut length (24 / Special plain paper) Deck 2 Compensation of cut length (24 / Special tracing paper) Deck 2 Compensation of cut length (24 / Special film) Deck 2 Compensation of cut length (30 / Plain paper) Deck 2 Compensation of cut length (30 / Tracing paper) Deck 2 Compensation of cut length (30 / Film) Deck 2 Compensation of cut length (30 / Special plain paper) Deck 2 Compensation of cut length (30 / Special tracing paper) Deck 2 Compensation of cut length (30 / Special film) Deck 2 Compensation of cut length (34 / Plain paper) Deck 2 Compensation of cut length (34 / Tracing paper) Deck 2 Compensation of cut length (34 / Film) Deck 2 Compensation of cut length (34 / Special plain paper) Deck 2 Compensation of cut length (34 / Special tracing paper) Deck 2 Compensation of cut length (34 / Special film) Deck 2 Compensation of cut length (36 / Plain paper) Deck 2 Compensation of cut length (36 / Tracing paper) Deck 2 Compensation of cut length (36 / Film) Deck 2 Compensation of cut length (36 / Special plain paper) Deck 2 Compensation of cut length (36 / Special tracing paper) Deck 2 Compensation of cut length (36 / Special film)
0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100
8-127 8-127 8-127 8-127 8-127 8-127 8-127 8-127 8-127 8-127 8-127 8-127 8-128 8-128 8-128 8-128 8-128 8-128 8-128 8-128 8-128 8-128 8-128 8-128 8-129 8-129 8-129 8-129 8-129 8-129 8-129 8-129 8-129 8-129 8-129 8-129 8-130 8-130 8-130 8-130 8-130 8-130 8-130 8-130 8-130 8-130 8-130 8-130 8-131 8-131 8-131 8-131 8-131 8-131 8-131 8-131 8-131 8-131 8-131 8-131
8-34
K105sm8e2_EUA
NOTE: All items greyed are not generally for field technician use
Item No. Setting Item Unit Default Value USA EUR / AS 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 52 50 50 50 50 50 50 50 50 50 50 50 54 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 1 1 1 1 1 0 0 0 0 1 1 1 0 0 0 0 Setting range Refer to page ;
577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620
Deck 2 Compensation of cut length (A3 / Plain paper) Deck 2 Compensation of cut length (A3 / Tracing paper) Deck 2 Compensation of cut length (A3 / Film) Deck 2 Compensation of cut length (A3 / Special plain paper) Deck 2 Compensation of cut length (A3 / Special tracing paper) Deck 2 Compensation of cut length (A3 / Special film) Deck 2 Compensation of cut length (A2 / Plain paper) Deck 2 Compensation of cut length (A2 / Tracing paper) Deck 2 Compensation of cut length (A2 / Film) Deck 2 Compensation of cut length (A2 / Special plain paper) Deck 2 Compensation of cut length (A2 / Special tracing paper) Deck 2 Compensation of cut length (A2 / Special film) Deck 2 Compensation of cut length (A1 / Plain paper) Deck 2 Compensation of cut length (A1 / Tracing paper) Deck 2 Compensation of cut length (A1 / Film) Deck 2 Compensation of cut length (A1 / Special plain paper) Deck 2 Compensation of cut length (A1 / Special tracing paper) Deck 2 Compensation of cut length (A1 / Special film) Deck 2 Compensation of cut length (A0 / Plain paper) Deck 2 Compensation of cut length (A0 / Tracing paper) Deck 2 Compensation of cut length (A0 / Film) Deck 2 Compensation of cut length (A0 / Special plain paper) Deck 2 Compensation of cut length (A0 / Special tracing paper) Deck 2 Compensation of cut length (A0 / Special film) Deck 2 Compensation of cut length (B1 / Plain paper) Deck 2 Compensation of cut length (B1 / Tracing paper) Deck 2 Compensation of cut length (B1 / Film) Deck 2 Compensation of cut length (B1 / Special plain paper) Deck 2 Compensation of cut length (B1 / Special tracing paper) Deck 2 Compensation of cut length (B1 / Special film) Deck 2 Compensation of cut length (880 / Plain paper) Deck 2 Compensation of cut length (880 / Tracing paper) Deck 2 Compensation of cut length (880 / Film) Deck 2 Compensation of cut length (880 / Special plain paper) Deck 2 Compensation of cut length (880 / Special tracing paper) Deck 2 Compensation of cut length (880 / Special film)
Judgement Value for Additional Cut Length for Nonstandard Size Prints (36/ 34/ 30/ A0 / B1) Judgement Value for Additional Cut Length for Nonstandard Size Prints (24/ 20/ A1) Judgement Value for Additional Cut Length for Nonstandard Size Prints (18/ 17/ 15/ A2) Judgement Value for Additional Cut Length for Nonstandard Size Prints (12/ 11/ A3) Additional Cut Length for Non-standard Size Prints (36/ 34/ 30/ A0 / B1) Additional Cut Length for Non-standard Size Prints (24/ 22/ A2) Additional Cut Length for Non-standard Size Prints (18/ 17/ 15/ A2) Additional Cut Length for Non-standard Size Prints (12/ 11/ A3)
0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 1 to 20 1 to 20 1 to 20 1 to 20 0 to 35 0 to 35 0 to 35 0 to 35
8-132 8-132 8-132 8-132 8-132 8-132 8-132 8-132 8-132 8-132 8-132 8-132 8-133 8-133 8-133 8-133 8-133 8-133 8-133 8-133 8-133 8-133 8-133 8-133 8-134 8-134 8-134 8-134 8-134 8-134 8-134 8-134 8-134 8-134 8-134 8-134 8-135 8-135 8-135 8-135 8-137 8-137 8-137 8-137
8-35
K105sm8e2_EUA
8. 5. 4
8. 5. 4. 1
It is possible to specify where to start printing the image at the leading edge of the media. If you increase the setting value by +1 , the head of image is shifted 1mm downward toward the trailing edge As a result the leading margin becomes larger.
Item No. 000 001 Setting Item Leading Registration (Roll paper) Leading Registration (Cut sheet paper) Default value USA EUR/ASIA 17 19 18 20 Setting range 1 to 40 1 to 40 Step of increment 1mm 1mm
Leading Registration
value is increased.
value is decreased.
8. 5. 4. 2
It is possible to adjust the length of trailing margin. The length of trailing margin becomes 1mm longer if you Increase the setting value by +1 .
Item No. 002 003 Setting Item Trailing Margin (Roll paper) Trailing Margin (Cut sheet paper) Default value USA EUR/ASIA 9 10 9 10 Setting range 1 to 40 1 to 40 Step of increment 1mm 1mm
Trailing Margin
NOTE
Some trailing image may be lost if you decrease the value too much.
8-36
K105sm8e2_EUA
8. 5. 4. 3
It is possible to adjust the amount of side margin. (Both left and right) Each side margin becomes 1mm wider if you increase the setting value. (As a result the width of print image becomes 2mm narrower.)
Default value USA EUR/ASIA 0 0 Setting range 0 to 20 Step of increment 1mm
Side Margin
NOTE
Each print is compulsively provided with 3mm of side margins on both sides regardless of this setting.
8-37
K105sm8e2_EUA
8. 5. 4. 4
LED Strobe Time for Main Pixel of each Block (No.008 to 010)
It is possible to make the whole image of each Image Block (A, B and C) darker or lighter independently by changing the LED Strobe Time for the Main Pixels. As a result an even image density can be accomplished among 3 Image Blocks. The whole image of the concerning Image Block becomes darker if you increase the setting value.
Item No. 008 009 010 Setting Item LED Strobe Time for Main Pixel (Image Block A : Left) LED Strobe Time for Main Pixel (Image Block B : Center) LED Strobe Time for Main Pixel (Image Block C : Right) Default value USA EUR/ASIA 10 10 10 10 10 10 Setting range 0 to 13 0 to 13 0 to 13 Step of increment 1 micro second 1 micro second 1 micro second
Block A
Block B
Block C
Decrease the value of 008 to make the image of Block A lighter. Setting value is decreased. .
Increase the value of 010 to make the image of Block C darker. Default Setting value is increased
Main pixel
Supplemental pixel
Please read [REFERENCE] on the page 8-41 for the explanation about Main Pixel and Supplemental Pixel.
8-38
K105sm8e2_EUA
NOTE
(1) The LED Strobe Times specified in these 008, 009 and 010 are directly applied to the Test Print. If the setting values are 10 (for 008), 11 (for 009) and 12 (for 010), for example, the actual LED Strobe Times are also 10 (for block A), 11 (for block B) and 12 (for block C). In case of Test Print 008 : 10 microsecond 009 : 11 microsecond 010 : 12 microsecond Block A (10)
Block B (11)
Block C (12)
But in case of a copy or a plot, the density command (LED Strobe Time) sent from the output device (image scanner or controller) is applied to the Image Block A. And only the difference of setting values among 008, 009 and 010 are applied to the actual LED Strobe Time. If the density command from the output device is 8 microsecond and the setting values are 10 (for 008), 11 (for 009) and 12 (for 010), for example, the actual LED Strobe Times are 8 (for block A), 9 (for block B) and 10 (for block C). In case of copy or plot Density command from output device : 8 microsecond 008 : 10 microsecond 009 : 11 microsecond 010 : 12 microsecond Block A Block B Block C (8) (9) (10)
(2) If the value of density command (LED Strobe Time) sent from the output device is larger than 13 microsecond (Max.), it is automatically corrected to 13 microsecond. If it is smaller than 0 microsecond (Min.), it is corrected to 0 microsecond similarly. 8-39
K105sm8e2_EUA
8. 5. 4. 5
LED Strobe Time for IST (Supplemental Pixel) of each Block (No.011 to 013)
If such image as a diagonal line looks too weak, you can make it clearer by changing the LED Strobe Time for the Supplemental Pixels. The adjustment is available for each Image Block independently. A diagonal line comes to look clearer if you increase the setting value, as the LED Strobe Time for the Supplemental Pixels becomes longer.
Item No. 011 012 013 Setting Item LED Strobe Time for Supplemental Pixel (Image Block A : Left) LED Strobe Time for Supplemental Pixel (Image Block B : Center) LED Strobe Time for Supplemental Pixel (Image Block C : Right) Default value USA EUR/ASIA 0 0 0 0 0 0 Setting range 0 to 13 0 to 13 0 to 13 Step of increment 1 micro second 1 micro second 1 micro second
Block A
Block B
Block C
Increase the setting values of 011 and 013 to make the images of these blocks clearer.
Default
Supplemental pixel
Actual print image Please read [REFERENCE] on the page 8-41 for the explanation about Main Pixel and Supplemental Pixel.
8-40
K105sm8e2_EUA
Reference
Normally the KIP3000 takes 600 times of image exposure per inch for the vertical direction as its resolution is 600DPI. Pixels created by this normal timing is called [Main Pixel]. When a specific image pattern (like a diagonal line) is printed, however, the KIP3000 will make additional image exposure between vertically neighboring 2 Main Pixels. This additional image exposure is completed within a very short time. The pixel created by this additional process is called [Supplemental Pixel]. Normal image pattern In case of a certain image pattern Main Pixels Supplemental Pixels Main Pixels
Supplemental Pixels are provided so as to fill the space between Main Pixels. When we compare a vertical / horizontal 1 dot line and a diagonal 1 dot line, for example, the diagonal one looks vague and rough although the vertical / horizontal one looks clear and smooth. This is because the diagonal line has a wider space between Main Pixels than the vertical / horizontal one. If this space is filled with the Supplemental Pixel, diagonal line comes to look smoother and clearer. No Supplemental Pixel Supplemental Pixels are provided.
Direction of print
8. 5. 4. 6
It is possible to align the pixels between Image Blocks if there is a gap of pixels. The Image Block B is the standard, and both the Image Blocks A and C can be shifted vertically. If you increase the setting value by +1, the whole pixels of the concerning Image Block is shifted 1 line (pixel) to the trailing edge side.
Item No. 014 015 Setting Item Horizontal Alignment of Pixels between Image Blocks A & B Horizontal Alignment of Pixels between Image Blocks B & C Default value USA EUR/ASIA 8 8 8 8 Setting range 2 to 14 2 to 14 Step of increment 1 pixel 1 pixel
Decrease the value of 014 to shift the block A to the leading edge side.
Decrease the value of 015 to shift the block C to the trailing edge side.
8-42
K105sm8e2_EUA
8. 5. 4. 7
It is possible to make the print length longer or shorter. This setting is applied when the print command (plot & copy) is provided with the length information. ( this is command used on all standard pages printed from the IPS ) If you increase the setting value by +1, the print length becomes 1mm longer.
Default value USA EUR/ASIA 43 43 Setting range 0 to 100 Step of increment 1mm
Cut length
8. 5. 4. 8
It is possible to make the print length longer or shorter. This setting is applied when the print command (plot & copy) is not provided with the length information. ( This is may only be used on LONG prints over 6 meters on the IPS) If you increase the setting value by +1, the print length becomes 1mm longer.
Default value USA EUR/ASIA 50 50 Setting range 0 to 100 Step of increment 1mm
Cut length
8-43
K105sm8e3_EUA
8. 5. 4. 9
When you make a long print, the actual print length may become shorter than expected because the paper is likely to shrink. It is possible in this mode to compensate the print length manually. The length of long print is not compensated directly, but it is indirectly compensated by correcting the length of A1 print. If you increase the setting value by +1, the length of A1 print length becomes 0.1mm longer per 10mm.
Default value USA EUR/ASIA 500 500 Setting range 0 to 999 Step of increment 0.1mm
NOTE
(1) It is necessary to finish the adjustment of Cut Length 1 (No.016) before starting the adjustment in this Cut Length 3 (No.018). (2) This No.018 is the manual adjustment of the length of long print. But you can make the same adjustment in automatic way in the No.069. Refer to [8. 5. 4.37 Automatic Adjustment of Cut Length (Long print) (No.069)] on the page 8-62.
[Example of adjustment] 1. Supposing the actual length of a long print is shorter than expected.
100 100
Expected length
Actual length
50
50
0 C
8-44
K105sm8e3_EUA
2. Make an A1 (841mm long) or 34 long print. Measure the actual length of this A1 or 34 print to know how long millimeter it is shorter than expected. (Example : Print out is 838mm, so it is 3mm shorter than expected.)
Expected length A1 or 34
Actual length
3mm
3. Necessary value for the compensation is 10 times as long as the difference between actual length and expected length. It is 30 in this example. (3mm x 10 = 30) Specify 30 as the setting value of No.018.
4. Make a long print. The actual print out will be as long as expected. Expected length Actual length
100 100
50
50
0 C
8-45
K105sm8e3_EUA
NOTE
Please adjust the Developer Bias while checking the actual voltage with the multi-meter.
8-46
K105sm8e3_EUA
NOTE
There may be the case that the density of leading area, which corresponds to the 1st revolution of Drum, is darker than other area. In this case compensate the Developer Bias to have even density on both areas.
NOTE
(1) Please adjust Transfer Corona Analog Voltage while checking the actual voltage with the multi-meter. (2) For machines that correspond to both of the followings, set No.029, 030, 031 to 170. S/N 10511288 and before, 10511361 to 10511504 Without TE Quality Enhancement Kit 8-47
K105sm8e3_EUA
NOTE
You may lose some leading image as the following example if you increase the setting value too much, because the timing to start discharging is too much delayed. Normal Setting value is increased too much. Transfer Corona starts discharging at this point.
8-48
K105sm8e3_EUA
NOTE
(1) You may lose some trailing image as the following example if you decrease the setting value too much, because the Transfer Corona stops discharging too early. Normal Setting value is increased too much.
Transfer Corona stops discharging at this point. (2) For machines that correspond to both of the followings, set No.038 to 23. S/N 10511288 and before, 10511361 to 10511504 Without TE Quality Enhancement Kit
8-49
K105sm8e3_EUA
(oC)
0 Turn on Ready
(Time)
8-50
K105sm8e3_EUA
(Time)
Setting value of 046 (Example : 100 oC) 0 (Time) Warm Sleep starts. 100 oC is maintained after this point. 8-51
K105sm8e3_EUA
NOTE
(1) Overshoot works only when the temperature of Fuser Roller is colder than 50 oC. (2) When Overshoot works, the machine gets ready when the temperature of Fuser Roller reaches the sum value of Fuser Temperature and Overshoot. (The machine will get ready when the temperature of Fuser Roller reaches 170 oC in case of the above example.) (3) The purpose of Overshoot is to stabilize the image fusing even right after turning on.
8-52
K105sm8e3_EUA
Example : Value of No.048 (Fuser Temperature Control Range) is 10 Value of No.039 (Fuser Temperature) is 160 Highest limit of control range (170 oC) (oC) Fuser Lamp turns OFF. Fuser Temperature (160 oC)
(Time)
8-53
K105sm8e3_EUA
Toner Low
Motor stops
NOTE
The reaction time may be too long if the image gets lighter and lighter when you make large volume prints continuously. In this case try to decrease the setting value of No.050 to shorten the reaction time.
Toner Low
Motor stops
NOTE
The ON time may be too short if the image gets lighter and lighter when you make large volume prints continuously. In this case try to increase the setting value of No.051 to make the ON time longer.
8-54
K105sm8e3_EUA
Reference
(1) An isolated dot image tends to look so weak. The Dot Enhancement function emphasizes the isolated dot so that it looks clear. (Dot Enhancement function emphasizes only the isolated dot. It will not emphasize the dots coming together some degree.) Dot Enhancement function is OFF. Dot Enhancement function is ON.
(2) The Dot Enhancement function can be validated in the User Mode. It will not work if not validated.
8-55
K105sm8e3_EUA
8. 5. 4.24
The Feed Clutch turns OFF for a very short period whenever the machine transports the paper 3 meters long, so as to remove the paper slack in a long printing. It is possible in this No.053 to specify how long period the Feed Clutch continues to be OFF.
Default value USA EUR/ASIA 130 130 Setting range 80 to 180 Step of increment 1msec.
3 meters
3 meters
3 meters
8-56
K105sm8e3_EUA
The Toner Supply Roller Bias is high (-50 +/-5V against the Developer Roller Bias) right after starting the print. When the leading edge reaches the position at X millimetre from the sensor (PH6), which you have specified in the No.054, the Toner Supply Roller Bias changes to low (-150 +/-5V against the Developer Roller Bias).
PH6
Toner Supply Roller Bias changes from high to low when the leading edge of paper reaches here.
Reference
Toner Supply Roller Bias changes from low to high when the trailing edge of paper reaches the position at X millimetre from the sensor (PH1). Setting value of No.054 (X millimetre)
PH1
Toner Supply Roller Bias changes from low to high when the leading edge of paper reaches here. 8-57
K105sm8e3_EUA
8-58
K105sm8e3_EUA
NOTE
We will not guarantee the print quality if the print is longer than the following sizes. 36 plain paper Other sizes of plain paper Tracing paper Film 3.6m 3 times as long as each standard size Twice as long as each standard size Standard sizes
8-59
K105sm8e3_EUA
Reference
The Fuser Roller periodically rotates and then stops when the machine is ready, so as to equalize the temperature at every point of Fuser Roller. But if you feel it is so noisy to rotate it, select the setting value 1. In this case please note that the fusing quality may not be so good because the temperature of Fuser Roller is not equalized.
Reference
The Central Fuser Fan starts or stops working in the following conditions. Starts working : The right side of Fuser Roller becomes 1oC colder than the setting value of No.063 (or No.064), and also the central area of it becomes hotter than that of No.040 (or No.043). Stops working : The right side of Fuser Roller becomes 1oC hotter than the setting value of No.063 (or No.064), or the central area of it becomes 5oC colder than that of No.040 (or No.043).
8-60
K105sm8e3_EUA
stops
Reference
(1) The Drum reverse rotation may produce a slight amount of toner sticking on the Drums surface. This causes a black line at 50mm below the leading registration on a print. Setting a smaller value will reduce such a line. (2) Setting an extremely small value may cause an indentation on Developer Roller.
Reference
Sometimes you can avoid defect of transfer (light image) by making the Separation Lamp work. So if you feel the print image is too light, try to make it work. You may be able to fix the problem.
8-61
K105sm8e3_EUA
[Way of adjustment] 1. Select the Item Number 069 in the Adjustment Mode. 2. Set an A1 roll paper to the Roll Deck 1. 3. Press the [ENTER] Key. 4. The machine takes 4 sheets of 210mm long prints automatically. 5. Then, the machine also takes 4 sheets of 840mm prints automatically. 6. The machine automatically calculates the best compensation data from those 8 sheets of print. Press the [ * ] Key to write this data into the memory. (It will not be written in the memory if you press the [ENTER] Key.)
S t ep3 Da t a Wr i t e Y: N : ENTER
8-62
K105sm8e3_EUA
8. 5. 4.38 Compensation of Fuser Motor Speed for roll paper (Plain paper / A3, 12 & 11) (No.070 to 075)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper of A3, 12 and 11 sizes by roll paper feeding.
Item No. 070 071 072 073 074 075 Setting Item Fuser Motor 1st Speed (Roll / Plain paper / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll / Plain paper / A3, 12 & 11) Fuser Motor 2nd Speed (Roll / Plain paper / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll / Plain paper / A3, 12 & 11) Fuser Motor 3rd Speed (Roll / Plain paper / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll / Plain paper / A3, 12 & 11) Default value USA EUR/ASIA 25 23 1 1 27 2 20 2 25 2 21 2 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
Reference
Sometimes crease of paper or defective image may occur when you make a very long print with a constant Fuser Motor Speed. Fuser Motor Speed is constant
100
Leading edge
50
A B C
Defective image
Crease of paper
It is effective to fix these problems if we change the Fuser Motor Speed step by step during 1 sheet of print. The Fuser Motor speed can be changed 3 times in maximum for 1 sheet of print. At first the Fuser Motor rotates obeying the setting of Fuser Motor Speed (specified in No.316 to 321). After that it changes its rotation speed step by step obeying the settings of No.070 to 075.
Fuser Motor 1st Speed Switch Timing (No.071) Fuser Motor Speed (No.316) Fuser Motor 2nd Speed Switch Timing (No.073) Fuser Motor 1st Speed (No.070) Fuser Motor 2nd Speed (No.072) Fuser Motor 3rd Speed Switch Timing (No.075) Fuser Motor 3rd Speed (No.074)
100 A 50 B C
8-63
K105sm8e4_EUA
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.070, 072 and 074. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. (The default setting value 20 corresponds to 60mm/second.) (Example) Setting value of 070 is 21 Setting value of 072 is 22 Setting value of 074 is 23 Fuser Motor 1st Speed is 60.06mm/sec. Fuser Motor 2nd Speed is 60.12mm/sec. Fuser Motor 3rd Speed is 60.18mm/sec.
Fuser Motor 1st Speed (60.06mm/sec.) Fuser Motor 2nd Speed (60.12mm/sec.) Fuser Motor 3rd Speed (60.18mm/sec.)
100 A 50 B C
You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.071, 073 and 075. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. (If you specify 0, the Fuser Motor Speed does not change.) (Example) Setting value of 071 is 5 Setting value of 073 is 10 Setting value of 075 is 15 Fuser Motor 1st Speed starts 5 seconds after the Registration Sensor detects the leading edge. Fuser Motor 2nd Speed starts 10 seconds after the start of Fuser Motor 1st Speed. Fuser Motor 2nd Speed starts 15 seconds after the start of Fuser Motor 1st Speed.
15 seconds (Fuser Motor 2nd Speed)
100 A 50 B C
8-64
K105sm8e4_EUA
8. 5. 4.39 Compensation of Fuser Motor Speed for roll paper (Tracing paper / A3, 12 & 11) (No.076 to 081)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper of A3, 12 and 11 sizes by roll paper feeding.
Item No. 076 077 078 079 080 081 Setting Item Fuser Motor 1st Speed (Roll / Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll / Tracing / A3, 12 & 11) Fuser Motor 2nd Speed (Roll / Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll / Tracing / A3, 12 & 11) Fuser Motor 3rd Speed (Roll / Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll / Tracing / A3, 12 & 11) Default value USA EUR/ASIA 23 23 1 1 23 2 23 3 23 2 23 3 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.076, 078 and 080. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.077, 079 and 081. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-65
K105sm8e4_EUA
8. 5. 4.40 Compensation of Fuser Motor Speed for roll paper (Film / A3, 12 & 11) (No.082 to 087)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film of A3, 12 and 11 sizes by roll paper feeding.
Item No. 082 083 084 085 086 087 Setting Item Fuser Motor 1st Speed (Roll / Film / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll / Film / A3, 12 & 11) Fuser Motor 2nd Speed (Roll / Film / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll / Film / A3, 12 & 11) Fuser Motor 3rd Speed (Roll / Film / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll / Film / A3, 12 & 11) Default value USA EUR/ASIA 25 22 1 1 25 2 20 0 22 2 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.082, 084 and 086. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.083, 085 and 087. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-66
K105sm8e4_EUA
8. 5. 4.41 Compensation of Fuser Motor Speed for roll paper (Special plain paper / A3, 12 & 11) (No.088 to 093)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper (special media) of A3, 12 and 11 sizes by roll paper feeding.
Item No. 088 089 090 091 092 093 Setting Item Fuser Motor 1st Speed (Roll / Special plain paper / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll / Special plain paper / A3, 12 & 11) Fuser Motor 2nd Speed Setting (Roll / Special plain paper / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll / Special plain paper / A3, 12 & 11) Fuser Motor 3rd Speed (Roll / Special plain paper / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll / Special plain paper / A3, 12 & 11) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.088, 090 and 092. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.089, 091 and 093. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-67
K105sm8e4_EUA
8. 5. 4.42 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A3, 12 & 11) (No.094 to 099)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper (special media) of A3, 12 and 11 sizes by roll paper feeding.
Item No. 094 095 096 097 098 099 Setting Item Fuser Motor 1st Speed (Roll/ Special Media / Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll/ Special Media / Tracing / A3, 12 & 11) Fuser Motor 2nd Speed (Roll/ Special Media / Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll/ Special Media / Tracing / A3, 12 & 11) Fuser Motor 3rd Speed (Roll/ Special Media / Tracing / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll/ Special Media / Tracing / A3, 12 & 11) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.094, 096 and 098. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.095, 097 and 099. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-68
K105sm8e4_EUA
8. 5. 4.43 Compensation of Fuser Motor Speed for roll paper (Special film / A3, 12 & 11) (No.100 to 105)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film (special media) of A3, 12 and 11 sizes by roll paper feeding.
Item No. 100 101 102 103 104 105 Setting Item Fuser Motor 1st Speed (Roll / Special film / A3, 12 & 11) Switch Timing to Fuser Motor 1st Speed (Roll / Special film / A3, 12 & 11) Fuser Motor 2nd Speed (Roll / Special film / A3, 12 & 11) Switch Timing to Fuser Motor 2nd Speed (Roll / Special film / A3, 12 & 11) Fuser Motor 3rd Speed (Roll / Special film / A3, 12 & 11) Switch Timing to Fuser Motor 3rd Speed (Roll / Special film / A3, 12 & 11) Default value USA EUR/ASIA 20 20 0 0 20 0 20 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.100, 102 and 104. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.101, 103 and 105. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-69
K105sm8e4_EUA
8. 5. 4.44 Compensation of Fuser Motor Speed for roll paper (Plain paper / A2, 18 & 17) (No.106 to 111)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper of A2, 18 and 17 sizes by roll paper feeding.
Item No. 106 107 108 109 110 111 Setting Item Fuser Motor 1st Speed (Roll / Plain paper / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll / Plain paper / A2, 18 & 17) Fuser Motor 2nd Speed (Roll / Plain paper / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll / Plain paper / A2, 18 & 17) Fuser Motor 3rd Speed (Roll / Plain paper / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll / Plain paper / A2, 18 & 17) Default value USA EUR/ASIA 23 22 1 1 24 3 23 5 24 3 22 5 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.106, 108 and 110. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.107, 109 and 111. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-70
K105sm8e4_EUA
8. 5. 4.45 Compensation of Fuser Motor Speed for roll paper (Tracing paper / A2, 18 & 17) (No.112 to 117)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper of A2, 18 and 17 sizes by roll paper feeding.
Item No. 112 113 114 115 116 117 Setting Item Fuser Motor 1st Speed (Roll / Tracing / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll / Tracing / A2, 18 & 17) Fuser Motor 2nd Speed (Roll / Tracing / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll / Tracing / A2, 18 & 17) Fuser Motor 3rd Speed (Roll / Tracing / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll / Tracing / A2, 18 & 17) Default value USA EUR/ASIA 23 23 1 1 24 3 24 3 24 3 24 3 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.112, 114 and 116. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.113, 115 and 117. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-71
K105sm8e4_EUA
8. 5. 4.46 Compensation of Fuser Motor Speed for roll paper (Film / A2, 18 & 17) (No.118 to 123)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film of A2, 18 and 17 sizes by roll paper feeding.
Item No. 118 119 120 121 122 123 Setting Item Fuser Motor 1st Speed (Roll / Film / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll / Film / A2, 18 & 17) Fuser Motor 2nd Speed (Roll / Film / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll / Film / A2, 18 & 17) Fuser Motor 3rd Speed (Roll / Film / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll / Film / A2, 18 & 17) Default value USA EUR/ASIA 25 22 1 1 25 3 20 0 22 3 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.118, 120 and 122. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.119, 121 and 123. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-72
K105sm8e4_EUA
8. 5. 4.47 Compensation of Fuser Motor Speed for roll paper (Special plain paper / A2, 18 & 17) (No.124 to 129)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper (special media) of A2, 18 and 17 sizes by roll paper feeding.
Item No. 124 125 126 127 128 129 Setting Item Fuser Motor 1st Speed (Roll / Special plain paper / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll / Special plain paper / A2, 18 & 17) Fuser Motor 2nd Speed (Roll / Special plain paper / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll / Special plain paper / A2, 18 & 17) Fuser Motor 3rd Speed (Roll / Special plain paper / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll / Special plain paper / A2, 18 & 17) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.124, 126 and 128. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.125, 127 and 129. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-73
K105sm8e4_EUA
8. 5. 4.48 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A2, 18 & 17) (No.130 to 135)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper (special media) of A2, 18 and 17 size by roll paper feeding.
Item No. 130 131 132 133 134 135 Setting Item Fuser Motor 1st Speed (Roll / Special tracing / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll / Special tracing / A2, 18 & 17) Fuser Motor 2nd Speed (Roll / Special tracing / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll / Special tracing / A2, 18 & 17) Fuser Motor 3rd Speed (Roll / Special tracing / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll / Special tracing / A2, 18 & 17) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.130, 132 and 134. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.131, 133 and 135. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-74
K105sm8e4_EUA
8. 5. 4.49 Compensation of Fuser Motor Speed for roll paper (Special film / A2, 18 & 17) (No.136 to 141)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film (special media) of A2, 18 and 17 sizes by roll paper feeding.
Item No. 136 137 138 139 140 141 Setting Item Fuser Motor 1st Speed (Roll / Special film / A2, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Roll / Special film / A2, 18 & 17) Fuser Motor 2nd Speed (Roll / Special film / A2, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Roll / Special film / A2, 18 & 17) Fuser Motor 3rd Speed (Roll / Special film / A2, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Roll / Special film / A2, 18 & 17) Default value USA EUR/ASIA 20 20 0 0 20 0 20 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.136, 138 and 140. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.137, 139 and 141. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-75
K105sm8e4_EUA
8. 5. 4.50 Compensation of Fuser Motor Speed for roll paper (Plain paper / A1, 24 & 22) (No.142 to 147)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper of A1, 24 and 22 sizes by roll paper feeding.
Item No. 142 143 144 145 146 147 Setting Item Fuser Motor 1st Speed (Roll / Plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll / Plain paper / A1, 24 & 22) Fuser Motor 2nd Speed (Roll / Plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll / Plain paper / A1, 24 & 22) Fuser Motor 3rd Speed (Roll / Plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll / Plain paper / A1, 24 & 22) Default value USA EUR/ASIA 22 21 1 1 21 7 21 8 22 7 21 8 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.142, 144 and 146. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.143, 145 and 147. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-76
K105sm8e4_EUA
8. 5. 4.51 Compensation of Fuser Motor Speed for roll paper (Tracing paper / A1, 24 & 22) (No.148 to 153)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper of A1, 24 and 22 sizes by roll paper feeding.
Item No. 148 149 150 151 152 153 Setting Item Fuser Motor 1st Speed (Roll / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll / Tracing / A1, 24 & 22) Fuser Motor 2nd Speed (Roll / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll / Tracing / A1, 24 & 22) Fuser Motor 3rd Speed (Roll / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll / Tracing / A1, 24 & 22) Default value USA EUR/ASIA 22 22 1 1 23 7 22 5 24 7 23 5 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.148, 150 and 152. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.149, 151 and 153. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-77
K105sm8e4_EUA
8. 5. 4.52 Compensation of Fuser Motor Speed for roll paper (Film / A1, 24 & 22) (No.154 to 159)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film of A1, 24 and 22 sizes by roll paper feeding.
Item No. 154 155 156 157 158 159 Setting Item Fuser Motor 1st Speed (Roll / Film / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll / Film / A1, 24 & 22) Fuser Motor 2nd Speed (Roll / Film / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll / Film / A1, 24 & 22) Fuser Motor 3rd Speed (Roll / Film / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll / Film / A1, 24 & 22) Default value USA EUR/ASIA 21 21 1 1 21 7 20 0 21 7 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.154, 156 and 158. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.155, 157 and 159. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-78
K105sm8e4_EUA
8. 5. 4.53 Compensation of Fuser Motor Speed for roll paper (Special plain paper / A1, 24 & 22) (No.160 to 165)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper (special media) of A1, 24 and 22 sizes by roll paper feeding.
Item No. 160 161 162 163 164 165 Setting Item Fuser Motor 1st Speed (Roll / Special plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll / Special plain paper / A1, 24 & 22) Fuser Motor 2nd Speed (Roll / Special plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll / Special plain paper / A1, 24 & 22) Fuser Motor 3rd Speed (Roll / Special plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll / Special plain paper / A1, 24 & 22) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.160, 162 and 164. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.161, 163 and 165. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-79
K105sm8e4_EUA
8. 5. 4.54 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A1, 24 & 22) (No.166 to 171)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper (special media) of A1, 24 and 22 size by roll paper feeding.
Item No. 166 167 168 169 170 171 Setting Item Fuser Motor 1st Speed (Roll / Special tracing / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll / Special tracing / A1, 24 & 22) Fuser Motor 2nd Speed (Roll / Special tracing / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll / Special tracing / A1, 24 & 22) Fuser Motor 3rd Speed (Roll / Special tracing / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll / Special tracing / A1, 24 & 22) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.166, 168 and 170. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.167, 169 and 171. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-80
K105sm8e4_EUA
8. 5. 4.55 Compensation of Fuser Motor Speed for roll paper (Special film / A1, 24 & 22) (No.172 to 177)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film (special media) of A1, 24 and 22 sizes by roll paper feeding.
Item No. 172 173 174 175 176 177 Setting Item Fuser Motor 1st Speed (Roll / Special film / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Roll / Special film / A1, 24 & 22) Fuser Motor 2nd Speed (Roll / Special film / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Roll / Special film / A1, 24 & 22) Fuser Motor 3rd Speed (Roll / Special film / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Roll / Special film / A1, 24 & 22) Default value USA EUR/ASIA 20 20 0 0 20 0 20 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.172, 174 and 176. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.173, 175 and 177. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-81
K105sm8e4_EUA
8. 5. 4.56 Compensation of Fuser Motor Speed for roll paper (Plain paper / A0, 36 & 34) (No.178 to 183)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper of A0, 36 and 34 sizes by roll paper feeding.
Item No. 178 179 180 181 182 183 Setting Item Fuser Motor 1st Speed (Roll / Plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll / Plain paper / A0, 36 & 34) Fuser Motor 2nd Speed (Roll / Plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll / Plain paper / A0, 36 & 34) Fuser Motor 3rd Speed (Roll / Plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll / Plain paper / A0, 36 & 34) Default value USA EUR/ASIA 19 18 1 1 19 12 20 11 19 12 18 11 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.178, 180 and 182. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.179, 181 and 183. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-82
K105sm8e4_EUA
8. 5. 4.57 Compensation of Fuser Motor Speed for roll paper (Tracing paper / A0, 36 & 34) (No.184 to 189)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper of A0, 36 and 34 sizes by roll paper feeding.
Item No. 184 185 186 187 188 189 Setting Item Fuser Motor 1st Speed (Roll / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll / Tracing / A0, 36 & 34) Fuser Motor 2nd Speed (Roll / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll / Tracing / A0, 36 & 34) Fuser Motor 3rd Speed (Roll / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll / Tracing / A0, 36 & 34) Default value USA EUR/ASIA 19 20 1 1 20 12 20 5 21 12 19 5 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.184, 186 and 188. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.185, 187 and 189. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-83
K105sm8e4_EUA
8. 5. 4.58 Compensation of Fuser Motor Speed for roll paper (Film / A0, 36 & 34) (No.190 to 195)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film of A0, 36 and 34 sizes by roll paper feeding.
Item No. 190 191 192 193 194 195 Setting Item Fuser Motor 1st Speed (Roll / Film / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll / Film / A0, 36 & 34) Fuser Motor 2nd Speed (Roll / Film / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll / Film / A0, 36 & 34) Fuser Motor 3rd Speed (Roll / Film / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll / Film / A0, 36 & 34) Default value USA EUR/ASIA 22 20 1 1 25 12 20 0 23 12 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.190, 192 and 194. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.191, 193 and 195. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-84
K105sm8e4_EUA
8. 5. 4.59 Compensation of Fuser Motor Speed for roll paper (Special plain paper / A0, 36 & 34) (No.196 to 201)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper (special media) of A0, 36 and 34 sizes by roll paper feeding.
Item No. 196 197 198 199 200 201 Setting Item Fuser Motor 1st Speed (Roll / Special plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll / Special plain paper / A0, 36 & 34) Fuser Motor 2nd Speed (Roll / Special plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll / Special plain paper / A0, 36 & 34) Fuser Motor 3rd Speed (Roll / Special plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll / Special plain paper / A0, 36 & 34) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.196, 198 and 200. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.197, 199 and 201. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-85
K105sm8e4_EUA
8. 5. 4.60 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A0, 36 & 34) (No.202 to 207)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper (special media) of A0, 36 and 34 size by roll paper feeding.
Item No. 202 203 204 205 206 207 Setting Item Fuser Motor 1st Speed (Roll / Special tracing / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll / Special tracing / A0, 36 & 34) Fuser Motor 2nd Speed (Roll / Special tracing / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll / Special tracing / A0, 36 & 34) Fuser Motor 3rd Speed (Roll / Special tracing / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll / Special tracing / A0, 36 & 34) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.202, 204 and 206. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.203, 205 and 207. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-86
K105sm8e4_EUA
8. 5. 4.61 Compensation of Fuser Motor Speed for roll paper (Special film / A0, 36 & 34) (No.208 to 213)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film (special media) of A0, 24 and 22 sizes by roll paper feeding.
Item No. 208 209 210 211 212 213 Setting Item Fuser Motor 1st Speed (Roll / Special film / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Roll / Special film / A0, 36 & 34) Fuser Motor 2nd Speed (Roll / Special film / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Roll / Special film / A0, 36 & 34) Fuser Motor 3rd Speed (Roll / Special film / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Roll / Special film / A0, 36 & 34) Default value USA EUR/ASIA 20 20 0 0 20 0 20 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.208, 210 and 212. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.209, 211 and 213. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-87
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.214 to 219.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.220 to 225.
8-88
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.226 to 231.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.232 to 237.
8-89
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.238 to 243.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.244 to 249.
8-90
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.250 to 255.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.256 to 261.
8-91
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.262 to 267.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.268 to 273.
8-92
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.274 to 279.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.280 to 285.
8-93
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.286 to 291.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.292 to 297.
8-94
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.298 to 303.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.304 to 309.
8-95
K105sm8e4_EUA
CAUTION
The Main Motor Speed is the basis for many other print settings. So you have to re-adjust all of these print settings if you change the Main Motor Speed.
NOTE
For machines that correspond to both of the followings, set No.322, 323 to 18, and No.324 to 23 S/N 10511288 and before, 10511361 to 10511504 Without TE Quality Enhancement Kit 8-96
K105sm8e4_EUA
8. 5. 4.81 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / A3, A2, 12, 11, 18 & 17) (No.328 to 333)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper of A2, 18 and 17 sizes by cut sheet bypass feeding.
Item No. 328 329 330 331 332 333 Setting Item Fuser Motor 1st Speed (Cut sheet / Plain paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Plain paper / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet / Plain paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Plain paper / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet / Plain paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Plain paper / A3, A2, 12, 11, 18 & 17) Default value USA EUR/ASIA 23 22 1 24 3 23 5 1 24 3 22 5 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.328, 330 and 332. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.329, 331 and 333. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-97
K105sm8e4_EUA
8. 5. 4.82 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / A3, A2, 12, 11, 18 & 17) (No.334 to 339)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper of A2, 18 and 17 sizes by cut sheet bypass feeding.
Item No. 334 335 336 337 338 339 Setting Item Fuser Motor 1st Speed (Cut sheet / Tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Tracing / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet / Tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Tracing / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet / Tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Tracing / A3, A2, 12, 11, 18 & 17) Default value USA EUR/ASIA 23 23 1 24 3 24 3 1 24 3 24 3 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.334, 336 and 338. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.335, 337 and 339. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-98
K105sm8e4_EUA
8. 5. 4.83 Compensation of Fuser Motor Speed for cut sheet paper (Film / A3, A2, 12, 11, 18 & 17) (No.340 to 345)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film of A2, 18 and 17 sizes by cut sheet bypass feeding.
Item No. 340 341 342 343 344 345 Setting Item Fuser Motor 1st Speed (Cut sheet / Film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Film / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet / Film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Film / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet / Film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Film / A3, A2, 12, 11, 18 & 17) Default value USA EUR/ASIA 25 22 1 25 3 20 0 1 22 3 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.340, 342 and 344. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.341, 343 and 345. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-99
K105sm8e4_EUA
8. 5. 4.84 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / A3, A2, 12, 11, 18 & 17) (No.346 to 351)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper (special media) of A2, 18 and 17 sizes by cut sheet bypass feeding.
Item No. 346 347 348 349 350 351 Setting Item Fuser Motor 1st Speed (Cut sheet / Special plain paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Special plain paper / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet / Special plain paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Special plain paper / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet / Special plain paper / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Special plain paper / A3, A2, 12, 11, 18 & 17) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.346, 348 and 350. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.347, 349 and 351. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-100
K105sm8e4_EUA
8. 5. 4.85 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / A3, A2, 12, 11, 18 & 17) (No.352 to 357)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper (special media) of A2, 18 and 17 size by cut sheet bypass feeding.
Item No. 352 353 354 355 356 357 Setting Item Fuser Motor 1st Speed (Cut sheet / Special tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Special tracing / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet / Special tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Special tracing / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet / Special tracing / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Special tracing / A3, A2, 12, 11, 18 & 17) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.352, 354 and 356. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.353, 355 and 357. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-101
K105sm8e4_EUA
8. 5. 4.86 Compensation of Fuser Motor Speed for cut sheet paper (Special film / A3, A2, 12, 11, 18 & 17) (No.358 to 363)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film (special media) of A2, 18 and 17 sizes by cut sheet bypass feeding.
Item No. 358 359 360 361 362 363 Setting Item Fuser Motor 1st Speed (Cut sheet / Special film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Special film / A3, A2, 12, 11, 18 & 17) Fuser Motor 2nd Speed (Cut sheet / Special film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Special film / A3, A2, 12, 11, 18 & 17) Fuser Motor 3rd Speed (Cut sheet / Special film / A3, A2, 12, 11, 18 & 17) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Special film / A3, A2, 12, 11, 18 & 17) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.358, 360 and 362. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.359, 361 and 363. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-102
K105sm8e4_EUA
8. 5. 4.87 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / A1, 24 & 22) (No.364 to 369)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper of A1, 24 and 22 sizes by cut sheet bypass feeding.
Item No. 364 365 366 367 368 369 Setting Item Fuser Motor 1st Speed (Cut sheet / Plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Plain paper / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet / Plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Plain paper / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet / Plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Plain paper / A1, 24 & 22) Default value USA EUR/ASIA 22 21 1 21 7 21 8 1 22 7 21 8 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.364, 366 and 368. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.365, 367 and 369. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-103
K105sm8e4_EUA
8. 5. 4.88 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / A1, 24 & 22) (No.370 to 375)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper of A1, 24 and 22 sizes by cut sheet bypass feeding.
Item No. 370 371 372 373 374 375 Setting Item Fuser Motor 1st Speed (Cut sheet / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Tracing / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Tracing / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet / Tracing / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Tracing / A1, 24 & 22) Default value USA EUR/ASIA 22 22 1 1 23 7 22 5 24 7 23 5 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.370, 372 and 374. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.371, 373 and 375. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-104
K105sm8e4_EUA
8. 5. 4.89 Compensation of Fuser Motor Speed for cut sheet paper (Film / A1, 24 & 22) (No.376 to 381)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film of A1, 24 and 22 sizes by cut sheet bypass feeding.
Item No. 376 377 378 379 380 381 Setting Item Fuser Motor 1st Speed (Cut sheet / Film / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Film / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet / Film / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Film / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet / Film / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Film / A1, 24 & 22) Default value USA EUR/ASIA 21 21 1 1 21 7 20 0 21 7 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.376, 378 and 380. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.377, 379 and 381. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-105
K105sm8e4_EUA
8. 5. 4.90 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / A1, 24 & 22) (No.382 to 387)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper (special media) of A1, 24 and 22 sizes by cut sheet bypass feeding.
Item No. 382 383 384 385 386 387 Setting Item Fuser Motor 1st Speed (Cut sheet / Special plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Special plain paper / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet / Special plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Special plain paper / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet / Special plain paper / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Special plain paper / A1, 24 & 22) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.382, 384 and 386. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.383, 385 and 387. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-106
K105sm8e4_EUA
8. 5. 4.91 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / A1, 24 & 22) (No.388 to 393)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper (special media) of A1, 24 and 22 size by cut sheet bypass feeding.
Item No. 388 389 390 391 392 393 Setting Item Fuser Motor 1st Speed (Cut sheet / Special tracing / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Special tracing / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet / Special tracing / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Special tracing / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet / Special tracing / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Special tracing / A1, 24 & 22) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.388, 390 and 392. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.389, 391 and 393. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-107
K105sm8e4_EUA
8. 5. 4.92 Compensation of Fuser Motor Speed for cut sheet paper (Special film / A1, 24 & 22) (No.394 to 399)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film (special media) of A1, 24 and 22 sizes by cut sheet bypass feeding.
Item No. 394 395 396 397 398 399 Setting Item Fuser Motor 1st Speed (Cut sheet / Special film / A1, 24 & 22) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Special film / A1, 24 & 22) Fuser Motor 2nd Speed (Cut sheet / Special film / A1, 24 & 22) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Special film / A1, 24 & 22) Fuser Motor 3rd Speed (Cut sheet / Special film / A1, 24 & 22) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Special film / A1, 24 & 22) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.394, 396 and 398. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.395, 397 and 399. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-108
K105sm8e4_EUA
8. 5. 4.93 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / A0, 36 & 34) (No.400 to 405)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper of A0, 36 and 34 sizes by cut sheet bypass feeding.
Item No. 400 401 402 403 404 405 Setting Item Fuser Motor 1st Speed (Cut sheet / Plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Plain paper / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet / Plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Plain paper / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet / Plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Plain paper / A0, 36 & 34) Default value USA EUR/ASIA 18 18 1 19 12 18 11 1 19 12 18 11 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.400, 402 and 404. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.401, 403 and 405. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-109
K105sm8e4_EUA
8. 5. 4.94 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / A0, 36 & 34) (No.406 to 411)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper of A0, 36 and 34 sizes by cut sheet bypass feeding.
Item No. 406 407 408 409 410 411 Setting Item Fuser Motor 1st Speed (Cut sheet / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Tracing / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Tracing / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet / Tracing / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Tracing / A0, 36 & 34) Default value USA EUR/ASIA 19 20 1 1 19 12 18 5 21 12 19 5 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.406, 408 and 410. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.407, 409 and 411. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-110
K105sm8e4_EUA
8. 5. 4.95 Compensation of Fuser Motor Speed for cut sheet paper (Film / A0, 36 & 34) (No.412 to 417)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film of A0, 36 and 34 sizes by cut sheet bypass feeding.
Item No. 412 413 414 415 416 417 Setting Item Fuser Motor 1st Speed (Cut sheet / Film / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Film / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet / Film / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Film / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet / Film / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Film / A0, 36 & 34) Default value USA EUR/ASIA
22 1 25 12 20 0 20 1 23 12 20 0
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.412, 414 and 416. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.413, 415 and 417. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-111
K105sm8e4_EUA
8. 5. 4.96 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / A0, 36 & 34) (No.418 to 423)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper (special media) of A0, 36 and 34 sizes by cut sheet bypass feeding.
Item No. 418 419 420 421 422 423 Setting Item Fuser Motor 1st Speed (Cut sheet / Special plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Special plain paper / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet / Special plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Special plain paper / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet / Special plain paper / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Special plain paper / A0, 36 & 34) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.418, 420 and 422. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.419, 421 and 423. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-112
K105sm8e4_EUA
8. 5. 4.97 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / A0, 36 & 34) (No.424 to 429)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper (special media) of A0, 36 and 34 size by cut sheet bypass feeding.
Item No. 424 425 426 427 428 429 Setting Item Fuser Motor 1st Speed (Cut sheet / Special tracing / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Special tracing / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet / Special tracing / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Special tracing / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet / Special tracing / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Special tracing / A0, 36 & 34) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.424, 426 and 428. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.425, 427 and 429. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-113
K105sm8e4_EUA
8. 5. 4.98 Compensation of Fuser Motor Speed for cut sheet paper (Special film / A0, 36 & 34) (No.430 to 435)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film (special media) of A0, 24 and 22 sizes by cut sheet bypass feeding.
Item No. 430 431 432 433 434 435 Setting Item Fuser Motor 1st Speed (Cut sheet / Special film / A0, 36 & 34) Switch Timing to Fuser Motor 1st Speed (Cut sheet / Special film / A0, 36 & 34) Fuser Motor 2nd Speed (Cut sheet / Special film / A0, 36 & 34) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / Special film / A0, 36 & 34) Fuser Motor 3rd Speed (Cut sheet / Special film / A0, 36 & 34) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / Special film / A0, 36 & 34) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.430, 432 and 434. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.431, 433 and 435. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-114
K105sm8e4_EUA
8. 5. 4.99 Compensation of Fuser Motor Speed for roll paper (Plain paper / 30) (No.436 to 441)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper of 30 size by roll paper feeding.
Item No. 436 437 438 439 440 441 Setting Item Fuser Motor 1st Speed (Roll / plain paper / 30) Switch Timing to Fuser Motor 1st Speed (Roll / plain paper / 30) Fuser Motor 2nd Speed (Roll / plain paper / 30) Switch Timing to Fuser Motor 2nd Speed (Roll / plain paper / 30) Fuser Motor 3rd Speed (Roll / plain paper / 30) Switch Timing to Fuser Motor 3rd Speed (Roll / plain paper / 30) Default value USA EUR/ASIA 21 20 1 1 20 12 22 11 20 12 20 11 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.436, 438 and 440. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.437, 439 and 441. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-115
K105sm8e4_EUA
8. 5. 4.100 Compensation of Fuser Motor Speed for roll paper (Tracing paper / 30) (No.442 to 447)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper of 30 size by roll paper feeding.
Item No. 442 443 444 445 446 447 Setting Item Fuser Motor 1st Speed (Roll / tracing / 30) Switch Timing to Fuser Motor 1st Speed (Roll / tracing / 30) Fuser Motor 2nd Speed (Roll / tracing / 30) Switch Timing to Fuser Motor 2nd Speed (Roll / tracing / 30) Fuser Motor 3rd Speed (Roll / tracing / 30) Switch Timing to Fuser Motor 3rd Speed (Roll / tracing / 30) Default value USA EUR/ASIA 22 23 1 1 21 12 23 5 22 12 21 5 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.442, 444 and 446. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.443, 445 and 447. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-116
K105sm8e4_EUA
8. 5. 4.101 Compensation of Fuser Motor Speed for roll paper (Film / 30) (No.448 to 453)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film of 30 size by roll paper feeding.
Item No. 448 449 450 451 452 453 Setting Item Fuser Motor 1st Speed (Roll / film / 30) Switch Timing to Fuser Motor 1st Speed (Roll / film / 30) Fuser Motor 2nd Speed (Roll / film / 30) Switch Timing to Fuser Motor 2nd Speed (Roll / film / 30) Fuser Motor 3rd Speed (Roll / film / 30) Switch Timing to Fuser Motor 3rd Speed (Roll / film / 30) Default value USA EUR/ASIA 22 20 1 1 25 23 12 12 20 20 0 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.448, 450 and 452. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.449, 451 and 453. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-117
K105sm8e4_EUA
8. 5. 4.102 Compensation of Fuser Motor Speed for roll paper (Special plain paper / 30) (No.454 to 459)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper (special media) of 30 size by roll paper feeding.
Item No. 454 455 456 457 458 459 Setting Item Fuser Motor 1st Speed (Roll / special plain paper / 30) Switch Timing to Fuser Motor 1st Speed (Roll / special plain paper / 30) Fuser Motor 2nd Speed (Roll / special plain paper / 30) Switch Timing to Fuser Motor 2nd Speed (Roll / special plain paper / 30) Fuser Motor 3rd Speed (Roll / special plain paper / 30) Switch Timing to Fuser Motor 3rd Speed (Roll / special plain paper / 30) Default value USA EUR/ASIA 20 20 0 0 20 0 20 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.454, 456 and 458. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.455, 457 and 459. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-118
K105sm8e4_EUA
8. 5. 4.103 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / 30) (No.460 to 465)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper (special media) of 30 size by roll paper feeding.
Item No. 460 461 462 463 464 465 Setting Item Fuser Motor 1st Speed (Roll / special tracing / 30) Switch Timing to Fuser Motor 1st Speed (Roll / special tracing / 30) Fuser Motor 2nd Speed (Roll / special tracing / 30) Switch Timing to Fuser Motor 2nd Speed (Roll / special tracing / 30) Fuser Motor 3rd Speed (Roll / special tracing / 30) Switch Timing to Fuser Motor 3rd Speed (Roll / special tracing / 30) Default value USA EUR/ASIA 20 20 0 0 20 0 20 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.460, 462 and 464. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.461, 463 and 465. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-119
K105sm8e4_EUA
8. 5. 4.104 Compensation of Fuser Motor Speed for roll paper (Special film / 30) (No.466 to 471)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film (special media) of 30 size by roll paper feeding.
Item No. 466 467 468 469 470 471 Setting Item Fuser Motor 1st Speed (Roll / special film / 30) Switch Timing to Fuser Motor 1st Speed (Roll / special film / 30) Fuser Motor 2nd Speed (Roll / special film / 30) Switch Timing to Fuser Motor 2nd Speed (Roll / special film / 30) Fuser Motor 3rd Speed (Roll / special film / 30) Switch Timing to Fuser Motor 3rd Speed (Roll / special film / 30) Default value USA EUR/ASIA 20 20 0 0 20 0 20 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.466, 468 and 470. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.467, 469 and 471. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-120
K105sm8e4_EUA
8. 5. 4.105 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / 30) (No.472 to 477)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper of 30 size by cut sheet bypass feeding.
Item No. 472 473 474 475 476 477 Setting Item Fuser Motor 1st Speed (Cut sheet / plain paper / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet / plain paper / 30) Fuser Motor 2nd Speed (Cut sheet / plain paper / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / plain paper / 30) Fuser Motor 3rd Speed (Cut sheet / plain paper / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / plain paper / 30) Default value USA EUR/ASIA 20 18 1 1 20 12 20 11 19 12 18 11 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.472, 474 and 476. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.473, 475 and 477. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-121
K105sm8e4_EUA
8. 5. 4.106 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / 30) (No.478 to 483)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper of 30 size by cut sheet bypass feeding.
Item No. 478 479 480 481 482 483 Setting Item Fuser Motor 1st Speed (Cut sheet / tracing / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet / tracing / 30) Fuser Motor 2nd Speed (Cut sheet / tracing / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / tracing / 30) Fuser Motor 3rd Speed (Cut sheet / tracing / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / tracing / 30) Default value USA EUR/ASIA 22 20 1 1 20 12 21 5 21 12 19 5 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.478, 480 and 482. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.479, 481 and 483. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-122
K105sm8e4_EUA
8. 5. 4.107 Compensation of Fuser Motor Speed for cut sheet paper (Film / 30) (No.484 to 489)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film of 30 size by cut sheet bypass feeding.
Item No. 484 485 486 487 488 489 Setting Item Fuser Motor 1st Speed (Cut sheet / film / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet / film / 30) Fuser Motor 2nd Speed (Cut sheet / film / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / film / 30) Fuser Motor 3rd Speed (Cut sheet / film / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / film / 30) Default value USA EUR/ASIA 22 20 1 1 25 12 20 0 23 12 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.484, 486 and 488. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.485, 487 and 489. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-123
K105sm8e4_EUA
8. 5. 4.108 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / 30) (No.490 to 495)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a plain paper (special media) of 30 size by cut sheet bypass feeding.
Item No. 490 491 492 493 494 495 Setting Item Fuser Motor 1st Speed (Cut sheet / special plain paper / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet / special plain paper / 30) Fuser Motor 2nd Speed (Cut sheet / special plain paper / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / special plain paper / 30) Fuser Motor 3rd Speed (Cut sheet / special plain paper / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / special plain paper / 30) Default value USA EUR/ASIA 20 20 0 20 0 20 0 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 1 second 1 second Step of increment
1 second
You can specify the Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.490, 492 and 494. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.491, 493 and 495. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8-124
K105sm8e4_EUA
8. 5. 4.109 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / 30) (No.496 to 501)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a tracing paper (special media) of 30 size by cut sheet bypass feeding.
Item No. 496 497 498 499 500 501 Setting Item Fuser Motor 1st Speed (Cut sheet / special tracing / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet / special tracing / 30) Fuser Motor 2nd Speed (Cut sheet / special tracing / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / special tracing / 30) Fuser Motor 3rd Speed (Cut sheet / special tracing / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / special tracing / 30) Default value USA EUR/ASIA 20 20 0 0 20 0 20 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.496, 498 and 500. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.497, 499 and 501. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings.
8. 5. 4.110 Compensation of Fuser Motor Speed for cut sheet paper (Special film / 30) (No.502 to 507)
It is possible to compensate the Fuser Motor speed specifying each Fuser Motor 1st, 2nd and 3rd Speed. It is also possible to specify when to switch the speed. (Switch timing) These settings become effective when you use a film (special media) of 30 size by cut sheet bypass feeding.
Item No. 502 503 504 505 506 507 Setting Item Fuser Motor 1st Speed (Cut sheet / special film / 30) Switch Timing to Fuser Motor 1st Speed (Cut sheet / special film / 30) Fuser Motor 2nd Speed (Cut sheet / special film / 30) Switch Timing to Fuser Motor 2nd Speed (Cut sheet / special film / 30) Fuser Motor 3rd Speed (Cut sheet / special film / 30) Switch Timing to Fuser Motor 3rd Speed (Cut sheet / special film / 30) Default value USA EUR/ASIA 20 20 0 0 20 0 20 0 20 0 20 0 Setting range 0 to 40 0 to 400 0 to 40 0 to 400 0 to 40 0 to 400 Step of increment 1 second 1 second 1 second
You can specify Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.502, 504 and 506. If you increase the setting value by +1, each Fuser Motor Speed becomes 0.06mm/second faster. You can specify the switch timing to each Fuser Motor 1st Speed, 2nd one and 3rd one in each Item No.503, 505 and 507. If you increase the setting value by +1, the timing to switch the speed is 1 second delayed. Please refer to the explanation on the pages 8-63 and 8-64 for the details of these settings. 8-125
K105sm8e4_EUA
8. 5. 4.111 Transfer Voltage applied at 100mm from trailing edge (Plain paper / Tracing paper / Film) (No.508 to 510)
It is possible to adjust the analog voltage to Transfer Corona on 100mm end of a print. This section does not function and is reserved for future update.
Item No. 508 509 510 Setting Item Default value USA EUR/ ASIA 255 255 255 255 255 255 Setting range Step of increment -
Transfer Voltage applied at 100mm from trailing edge (Plain) Transfer Voltage applied at 100mm from trailing edge (Tracing) Transfer Voltage applied at 100mm from trailing edge (Film)
NOTE
Keep the setting values unchanged from each default 255.
8. 5. 4.112 Transfer Voltage applied at 70mm from trailing edge (Plain paper / Tracing paper / Film) (No.511 to 513)
It is possible to adjust the analog voltage to Transfer Corona on 70mm end of a print. A setting combination among No.511 to No.516 can reduce ghost images on the bottom area of a print in some cases.
Item No. 511 512 513 Setting Item Default value USA EUR/ ASIA 33 33 33 33 255 255 Setting range 0 to 510 0 to 510 0 to 510 Step of increment -
Transfer Voltage applied at 70mm from trailing edge (Plain) Transfer Voltage applied at 70mm from trailing edge (Tracing) Transfer Voltage applied at 70mm from trailing edge (Film)
NOTE
For machines that correspond to both of the followings, set No.511, 512 to 255. S/N 10511288 and before, 10511361 to 10511504 Without TE Quality Enhancement Kit
8. 5. 4.113 Fuser Motor Speed applied at 30mm from trailing edge (Plain paper / Tracing paper / Film) (No.514 to 516)
It is possible to adjust the speed of Fuser Motor driving on 30mm end of a print. A setting combination among No.511 to No.516 can reduce ghost images on the bottom area of a print in some cases.
Item No. 514 515 516 Setting Item Default value USA EUR/ ASIA 16 16 16 16 0 0 Setting range 0 to 40 0 to 40 0 to 40 Step of increment -
Fuser Motor Speed applied at 30mm from trailing edge (Plain) Fuser Motor Speed applied at 30mm from trailing edge (Tracing) Fuser Motor Speed applied at 30mm from trailing edge (Film)
NOTE
For machines that correspond to both of the followings, set No.514, 515 to 0. S/N 10511288 and before, 10511361 to 10511504 Without TE Quality Enhancement Kit 8-126
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.517 to 522.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.523 to 528.
8-127
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.529 to 534.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.535 to 540.
8-128
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.541 to 546.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.547 to 552.
8-129
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.553 to 558.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.559 to 564.
8-130
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.565 to 570.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.571 to 576.
8-131
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.577 to 582.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.583 to 588.
8-132
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.589 to 594.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.595 to 600.
8-133
K105sm8e4_EUA
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.601 to 606.
NOTE
Please finish the basic adjustment of cut length (Cut Length 1 [No.016] and Cut Length 3 [No.018]) before starting to adjust these settings from No.607 to 612.
8-134
K105sm8e4_EUA
8. 5. 4.130 Judgement value for Additional Cut Length for Non-standard Size Prints (No.613 to 616)
It is possible to avoid the lack of trailing image on the non-standard size print, by providing additional paper length by service modes 4-617 to 4-620 (Additional Cut Length for non-standard size print). Additional Cut Length specified by service mode 4-617 to 4-620 is not always provided. Whether or not it is provided is judged by service mode 4-613 to 4-616 (Judgment value for Additional Cut Length for non-standard size print.)
Item No. 613 614 615 616 Setting Item Judgement value for Additional Cut Length for Non-standard Size Prints (36/ 34/ 30/ A0 / B1) Judgement value for Additional Cut Length for Non-standard Size Prints (24/ 20/ A1) Judgement value for Additional Cut Length for Non-standard Size Prints (18/ 17/ 15/ A2) Judgement value for Additional Cut Length for Non-standard Size Prints (12/ 11/ A3) Default value USA EUR/ASIA 1 1 1 1 1 1 1 1 Setting range 1 to 20 1 to 20 1 to 20 1 to 20 Step of increment 1mm 1mm 1mm 1mm
Reference
(1) Which Judgement Value / Additional Cut Length setting is applied to a non-standard size print depends on the corresponding roll width. Roll Width Standard Size Standard Cut Length 36" 841mm 34" 30" 728mm 24" 22" 594mm 18" 420mm 17" 15" 12" 11" 297mm (next page) 36"x48" A0 34"x44" 30"x42" B1 24"x36" 22"x34" A1 18"x24" A2 17"x22" 15"x21" 12"x18" 11"x17" A3 1219mm 1189mm 1118mm 1067mm 1030mm 914mm 864mm 841mm 610mm 594mm 559mm 533mm 457mm 432mm 420mm Judgement Value No.613 Additional Length No.617
No.614
No.618
No.615
No.619
No.616
No.620
8-135
K105sm8e4_EUA
Reference
(2) If the actual image length is longer than (or equal to) A+B, C is provided to the trailing edge of non-standard size print. A: Standard Cut Length (depends on roll width) B: Value of Judgement Value for Additional Cut Length for Non-standard Size Prints C: Value of Additional Cut Length for Non-standard Size Prints <Example> Actual Image Length: 860mm A: 841mm (A1 roll width) B: 10 C: 20
A (841mm) B (10)
C (20)
(3) If the actual image length is shorter than A+B, the print is cut as long as the actual image length. (C is not provided to the trailing edge of the print.) A: Standard Cut Length (depends on roll width) B: Value of Judgement Value for Additional Cut Length for Non-standard Size Prints C: Value of Additional Cut Length for Non-standard Size Prints <Example> Actual Image Length: 845mm A: 841mm (A1 roll width) B: 10 C: 20
A (841mm) Actual Image Length (845mm) B (10)
8-136
K105sm8e4_EUA
8. 5. 4.131 Additional Cut Length for Non-standard Size Prints (No.617 to 620)
It is possible to avoid the lack of trailing image on the non-standard size print, by providing additional paper length by service modes 4-617 to 4-620 (Additional Cut Length for non-standard size print). Additional Cut Length specified by service mode 4-617 to 4-620 is not always provided. Whether or not it is provided is judged by service mode 4-613 to 4-616 (Judgment value for Additional Cut Length for non-standard size print.)
Item No. 617 618 619 620 Setting Item Additional Cut Length for Non-standard Size Prints (36/ 34/ 30/ A0 / B1) Additional Cut Length for Non-standard Size Prints (24/ 22/ A2) Additional Cut Length for Non-standard Size Prints (18/ 17/ 15/ A2) Additional Cut Length for Non-standard Size Prints (12/ 11/ A3) Default value USA EUR/ASIA 0 0 0 0 0 0 0 0 Setting range 0 to 35 0 to 35 0 to 35 0 to 35 Step of increment 1mm 1mm 1mm 1mm
Refer to page 8-135 and 136 for Additional Cut Length and its Judgement Value.
8-137
K105sm8e4_EUA
8. 6
The Running Mode is prepared for factory use. Do not take the following operation because it is meaningless to do it in the field.
8. 6. 1
Function
In the Running Mode the machine takes usual printing operation even if no paper is installed. (If you install any paper it is transported and ejected from the printer as usual. But note that the printer continues printing endlessly.)
8. 6. 2
1. Indicate (5) Running Mode on the LCD pressing the [MENU] key.
2. Press the [ENTER] key, and you can enter the Running Mode.
3. In case the machine is provided with 2 Roll Decks, you can select either of them pressing the [ * ] Key.
4. Press the [ENTER] key, and the printer starts the printing operation. (This is called Running Operation.) (Start) is indicated when you start the Running Operation.
NOTE
(1) You can not go to other sub modes of the Service Mode unless you cancel the Running Operation. (2) Cut length and the image pattern rely on the settings specified in the Test Print Mode.
8-138
K105sm8e5_EUA
5. Press the [ENTER] key again to cancel the Running Operation. The indication changes to (Stop), and after that (Ready) is indicated when the Printing Operation has been completed.
Dec k 1 Runn i ng ( S t op ) Dec k 1 Runn i ng ( Ready )
NOTE
(-----) is indicated if the Running Operation is not available. It will be indicated in the following cases. 1. Any of paper jam, error or warning condition occurs. 2. Printer is not ready.
Dec k 1 Runn i ng (- - - - - )
8-139
K105sm8e5_EUA
8. 7
8. 7. 1
if the printer has any paper jam or other error, it is possible to mask (ignore) it in the Jam/Error Masking Mode. The jam or error is not detected when it is masked, you can operate the printer as usual even if the cause of jam or error is not removed.
NOTE
Masking condition will be cancelled if you cancel it manually in the Jam/Error Masking Mode or if you cancel the Service Mode.
8. 7. 2
1. Indicate (6) Mask Mode on the LCD pressing the [MENU] key.
2. Press the [ENTER] key, and you can enter the Jam/Error Masking Mode. The LCD indicates mask item (sensor name or error name) and status. Mask item
. R1 Se t R: 0
Sens o r E: 0
D: 0
Status
8-140
K105sm8e5_EUA
3. Pressing [ ] key or [ ] key, indicate the necessary mask item on the LCD. If you will mask any paper jam, go to the following step 4. If you will mask any error, go to the following step 6. Mask item (Indication on the LCD) Paper jam R1 Set Sensor R2 Set Sensor Feed Sensor Regist Sensor Manual Sensor Sep Sensor Exit Sensor Error M Motor Error F Motor Error P Motor Error Dev Motor Error Counter Error 1st Error Tr Error AC Error Bias Error FPGA Error Contents of mask Roll Deck 1 Jam Roll Deck 2 Jam Feeding Jam Registration Jam Bypass Feeder Jam Internal Jam Fuser Jam Main Motor Error Fuser Motor Error Paper Feed Motor Error Developer Motor Error Counter Error Image Corona Output Error Transfer Corona Output Error Separation Corona Output Error Developer Bias Output Error FPGA Configuration Error
4. In case you will mask any paper jam, press the [ENTER] Key several times to indicate the necessary mask item. (Example : You will mask the Registration Jam.)
. R1 Se t R: 0 Sens o r E: 0 . Reg i s t R: 0 Sens o r E: 0
D: 0
D: 0
8-141
K105sm8e5_EUA
5. Each paper jam occurs being related with 3 factors such as R (Remain), D (Delay) and E (Early arrival), which can be masked separately. The value 0 beside each factor means not masked, and 1 means masked. Press the [ENTER] Key several times until the necessary factor is masked.
. Reg i s t R: 0
Sens o r E: 0
D: 0
. Reg i s t R: 0
Sens o r E: 1
D: 0
Sens o r E: 0
D: 1
6. In case you will mask any error, press the [ENTER] Key several times to indicate the necessary mask item. (Example : You will mask the Main Motor Error.)
. R1 Se t R: 0 Sens o r E: 0 . M Mo t o r E r r o r
D: 0
7. Press the [ENTER] Key, and you can mask the selected mask item. Error Mask will be indicated when the selected mask item is in the mask condition.
. M Mo t o r E r r o r . M Mo t o r E r r o r E r r o r Mas k
NOTE
You can cancel the mask condition if you press the [ENTER] Key once more.
8-142
K105sm8e5_EUA
8. 8
8. 8. 1
Test Print Mode is available to make the printer perform printing operation by all alone (no output device is connected). The image patterns printed in the Test Print Mode are memorized in the printer.
8. 8. 2
1. Indicate (7) Test Mode on the LCD pressing the [MENU] key.
2. Press the [ENTER] key, and you can enter the Test Print Mode.
P r i n t e r Ready R1 : 36 R2 : 17
8-143
K105sm8e5_EUA
3. There are some kinds of Sub Item in the Test Print Mode. Please select the necessary Sub Item pressing [ ] and [ ] Keys. Please refer to the later pages as each Sub Mode is explained precisely. Print Mode
P r i n t e r Ready R1 : 36 R2 : 17
8-144
K105sm8e5_EUA
8. 8. 2. 1
Press the [ENTER] Key to start test printing. Now Printing is indicated during Test Print.
P r i n t e r Ready R1 : 36 R2 : 17 Now P r i n t i ng R1 : 36 R2 : 17
Press the [ENTER] key again if you want to stop the Test Print in the middle. Printing Stop is indicated.
Now P r i n t i ng R1 : 36 R2 : 17 P r i n t i ng S t op R1 : 36 R2 : 17
NOTE
In addition to the above indications, you will find such indications as Warming up, Printer stops., Warm Sleep, Cold Sleep and so on according to the condition of printer.
8. 8. 2. 2
Deck Selection
You can specify which paper source should be used for Test Print. Select either Roll 1 or Roll 2 pressing the [ENTER] Key.
. Dec k Se l ec t i on Ro l l 1 . Dec k Se l ec t i on Ro l l 2
The Bypass Feeder is selected as the paper source automatically if only you set the cut sheet paper. Manual is indicated in this case. (It becomes impossible to make Test Print with Roll 1 or Roll 2.)
. Dec k Se l ec t i on Manua l
8-145
K105sm8e5_EUA
8. 8. 2. 3
Paper Length
You can specify the paper length (cut length) of the Test Print. The following standard paper lengths are selectable. Metric : A0, A1, A2, A3, A4, A5, B1, B2, B3, B4 and B5 Inch : 48, 44, 42, 36, 34, 24, 22, 18, 17, 12, 11, 9 and 8.5 If you press the [ * ] key several times, you can magnify the standard size by the integral number. (For example the cut length becomes A0 x 2 (2378mm) if you press the [ * ] key once when A0 is selected. It will become A0 x 3 (3567mm) if you press twice.) 1. Indicate Paper Length on the LCD, and then press the [ENTER] key. The setting value (36x1 in this case) starts flashing showing that you can change the setting now.
. Pape r L eng t h 36 x 1
2. Change the paper length pressing [ ] key or [ ] key. And change the magnification pressing the [ * ] Key.
. Pape r L eng t h 36 x 1
] or [
] Key
. Pape r L eng t h 24 x 1
. Pape r L eng t h 24 x 1
[ * ] Key
. Pape r L eng t h 24 x 2
NOTE
Even if you specify a longer paper length than the maximum cut length, it is automatically corrected to the maximum cut length. (The maximum cut length relies on the paper size or the maximum cut length setting.)
3. Press the [ENTER] key to decide the setting. The setting value stops flashing when decided.
8-146
K105sm8e5_EUA
8. 8. 2. 4
Print Count
It is possible to specify how many sheets of test print should be done. 1. Indicate Print Count on the LCD, and then press the [ENTER] key. The setting value (001 Count in this case) starts flashing showing that you can change the setting now.
. P r i n t Coun t 001 Cou n t
] key or [ ] or [ ] Key
3. Press the [ENTER] key to decide the setting. The setting value stops flashing when decided.
8. 8. 2. 5
Image Pattern
You can choose which image pattern should be printed in the Test Print. 1. Indicate Image Pattern on the LCD, and then press the [ENTER] key. The setting value (P(0) S(0) in this case) starts flashing showing that you can change the setting now.
. Image Pa t t e r n P( 0) S( 0)
2. P(X) of the setting value means the Test Pattern Number Select the necessary Test Pattern Number pressing [ ] key or [
. Image Pa t t e r n P( 0) S( 0)
] key.
. Image Pa t t e r n P( 1) S( 0)
] or [
] Key
3. S(X) of the setting value means the size (enlargement or reduction of image pattern). Press and hold the [ * ] Key, and then press [ ] or [ ] Key to change the size.
. Image Pa t t e r n P( 1) S( 0)
].
. Image Pa t t e r n P( 1) S( 1)
4. Press the [ENTER] key to decide the setting. The setting value stops flashing when decided.
8-147
K105sm8e5_EUA
Reference
Examples of the test pattern images are shown below.
No.1
No.2
No.3
No.5 (halftone)
No.7
No.8 S(f)
8-148
K105sm8e5_EUA
8. 8. 2. 6
Manual Type
It is possible to make the printer recognize the type of cut sheet paper you will use. 1. Indicate Manual Type on the LCD, and press the [ENTER] key. The setting value (Plain in this case) starts flashing showing that you can change the setting now.
. Manua l Pl a i n T y pe
2. Pressing [
] key or [
T y pe
] key, indicate the type of the cut sheet paper you will use. [ ] or [ ] Key
. Manua l T y pe
. Manua l Pl a i n
T r ac i ng
3. Press the [ENTER] key to decide the setting. The indication stops flashing when decided.
8. 8. 2. 7
Manual Size
It is possible to make the printer recognize the size of cut sheet paper you will use. 1. Indicate Manual Size on the LCD, and press the [ENTER] key. The setting value (11x17 in this case) starts flashing showing that you can change the setting now.
. Manua l 11 x 17
Si ze
2. Indicate the same size with the used cut sheet paper pressing [
. Manua l 11 x 17 Si ze
] key or [
] key.
Si ze
] or [
] Key
. Manua l 18 x 12
3. Press the [ENTER] key to decide the setting. The indication stops flashing when decided.
8-149
K105sm8e5_EUA
8. 8. 2. 8
Roll 1 Type
It is possible to make the printer recognize the type of roll paper in the Roll Deck 1. 1. Indicate Roll 1 Type on the LCD, and press the [ENTER] key. The setting value (Plain in this case) starts flashing showing that you can change the setting now.
. R o l l 1 T y pe Pl a i n
2. Pressing [
] key or [
] key, indicate the type of the roll paper installed in the Roll 1. [ ] or [ ] Key
. R o l l 1 T y pe Pl a i n
. R o l l 1 T y pe T r ac i ng
3. Press the [ENTER] key to decide the setting. The indication stops flashing when decided.
8. 8. 2. 9
It is possible to make the printer recognize the size of roll paper in the Roll Deck 1. 1. Indicate either Roll 1 Size on the LCD, and press the [ENTER] key. The setting value (36 in this case) starts flashing showing that you can change the setting now.
. Ro l l 36 1 Si ze
2. Indicate the same size with the roll paper in the Roll Deck 1 pressing [
. Ro l l 36 1 Si ze
] key or [
] key.
] or [
] Key
. Ro l l 24
1 Si ze
3. Press the [ENTER] key to decide the setting. The setting value stops flashing when decided.
8-150
K105sm8e5_EUA
2. Pressing [
] key or [
] key, indicate the type of the roll paper installed in the Roll 2. [ ] or [ ] Key
. R o l l 2 T y pe Pl a i n
. R o l l 2 T y pe T r ac i ng
3. Press the [ENTER] key to decide the setting. The indication stops flashing when decided.
2. Indicate the same size with the roll paper in the Roll Deck 2 pressing [
. Ro l l 36 2 Si ze
] key or [
] key.
] or [
] Key
. Ro l l 24
2 Si ze
3. Press the [ENTER] key to decide the setting. The setting value stops flashing when decided.
8-151
K105sm8e5_EUA
8. 8. 2.12 Mirror
It is possible to print a mirror image. 1. Indicate Mirror on the LCD, and press the [ENTER] key. The setting value (OFF in this case) starts flashing showing that you can change the setting now.
.Mi r r o r OFF
] key or [ [ ] or [
] key. ] Key
.Mi r r o r O N
3. Press the [ENTER] key to decide the setting. The setting value stops flashing when decided.
8. 8. 2.13 Nega/Posi
It is possible to print a negative image. 1. Indicate Nega/Posi on the LCD, and press the [ENTER] key. The setting value (Positive in this case) starts flashing showing that you can change the setting now.
. Nega / Pos i Pos i t i v e
] key or [ ] Key
] key.
. Nega / Pos i Nega t i v e
] or [
3. Press the [ENTER] key to decide the setting. The setting value stops flashing when decided.
8-152
K105sm8e5_EUA
8. 8. 2.14 Scale
It is possible to print an image of scale on the printed paper for measuring purpose. 1. Indicate Scale on the LCD, and press the [ENTER] key. The setting value (OFF in this case) starts flashing showing that you can change the setting now.
. Sc a l e OFF
] key or [ [ ] or [
] key. ] Key
. Sc a l e ON
3. Press the [ENTER] key to decide the setting. The indication stops flashing when decided.
8-153
K105sm8e5_EUA
8. 9
8. 9. 1
This mode is used mainly in the Factory to adjust several units before shipment. The followings are available operations. Sub Mode No. 00 01 02 03 04 05 Available operation Main Motor rotates for 3 minutes. Drum rotates for 1 revolution. Also the Image Corona takes discharging when the Drum is rotating. Drum rotates for 1 revolution. Also the Transfer Corona takes discharging when the Drum is rotating. Drum rotates for 1 revolution. Also the Separation Corona takes discharging when the Drum is rotating. Main Motor rotates first, and then Bias is outputted for 3 minutes. The machine makes the same operation with the normal printing.
8. 9. 2
1. Indicate (8) Factory Mode on the LCD pressing the [MENU] key.
2. Press the [ENTER] key, and you can enter the Factory Adjustment Mode. The LCD indicates Sub Mode Number, Sub Mode Name and the status. Sub Mode No. Sub Mode Name
No00 Ma i n Mo t o r (- - - - - )
Status
3. Select the necessary Sub Mode pressing [ ] key or [ ] key. (Example : You will make the Transfer Corona operate.)
No00 Ma i n Mo t o r (- - - - - )
] or [
] Key
No02 T r Ou t pu t (- - - - - )
8-154
K105sm8e5_EUA
4. Press the [ENTER] key, and the selected object starts operating. Start is indicated when the selected object is operating. Press the [ENTER] key again to stop the operation in the middle. [ENTER] Key
No02 T r Ou t pu t (- - - - - )
No02 T r Ou t pu t (St a r t )
8-155
K105sm8e5_EUA
8.10
8.10. 1
Clear Mode
Function
It is possible to clear several kinds of information. The following modes are available. Name of mode RAM Clear Mode Error Clear Mode Jam Record Clear Mode Error Record Clear Mode Software Counter Setting Mode Total Counter Setting Mode Contents You can initialize all settings of Adjustment Mode and some other initial information memorized in the RAM. You can clear the error caused by the problem of Fuser Unit. You can clear the record of jams memorized in the memory. You can clear the record of errors memorized in the memory. You can input the value of Software Counter. You can input the value of Total Counter which is a kind of Software Counter.
NOTE
Record all the present data for the safety before you make RAM Clear.
8.10. 2
1. Indicate (9) Clear Mode on the LCD pressing the [MENU] key.
2. Press the [ENTER] key, and you can enter the Clear Mode.
. RAM C l ea r
8-156
K105sm8e5_EUA
3. Select any subordinate mode pressing [ ] key or [ ] key. Please read the later pages for the explanation about each mode.
. RAM C l ea r
. E r r o r C l ea r E- 000
. J am I n f o C l ea r C l ea r
. Er r o r C l ea r
I n f o Cl r
. Pr i n t
Coun t
0001154
. To t a l
Coun t
0001720
8-157
K105sm8e5_EUA
Ini t i al
s t at e
NOTE
The followings are possible errors caused by the problem of Fuser Unit. E-000 : Fuser Temperature Rising Error 1 E-001 : Fuser Over Temperature Error E-002 : Fuser Temperature Rising Error 2 E-003 : Fuser Low Temperature Error 1 E-004 : Fuser Low Temperature Error 2 Once anyone of the above occurs, it is impossible to make copy, plot and scan unless you clear it in the Error Clear Mode!
If the Fuser has any error, its error code is indicated in the LCD. To make Error Clear, press and hold the [ * ] key and then press the [ENTER] key. No error code will be indicated after the Error Clear. Press and hold the [ * ], and then press the [ENTER].
. E r r o r C l ea r E- 000
. E r r o r C l ea r
NOTE
Before you make Error Clear, please wait until the Fuser is enough cooled down.
8-158
K105sm8e5_EUA
. J am I n f o C l ea r
No jam code will be indicated in the No.22 (Jam Info) of the Information Mode.
. Er r o r
I n f o Cl r
No error code will be indicated in the No.23 (Error Info) of the Information Mode.
8-159
K105sm8e5_EUA
NOTE
The KIP3000 has a Software Counter which was synchronized with the Hardware Counter. These are displayed in the UI. It is not necessary to change the value unless the PW10520 PCB is replaced or value lost to reset. In this case set the value in this mode.
1. Indicate the Software Counter Setting Mode, and then press the [ENTER] Key. The 1st digit of the counted value starts flashing and it becomes possible to change it.
. Pr i n t
Coun t
. Pr i n t
Coun t
0001154
0001154
] key or [ Press [
] key. ] or [ ] Key.
. Pr i n t Coun t
0001154
0001150
3. If you press the [ * ] Key, one more upper digit flashes. Change the value in the same way.
. Pr i n t Coun t
. Pr i n t
Coun t
0001150
0001150
4. Press the [ENTER] key to decide the setting. The indication stops flashing when decided.
8-160
K105sm8e5_EUA
NOTE
The counting unit of Total Counter is always linear meter. Note that you can not change it.
1. Indicate the Total Counter Setting Mode, and then press the [ENTER] Key. The 1st digit of the counted value starts flashing and it becomes possible to change it.
. To t a l Coun t
. To t a l
Coun t
0001720
0001720
] key or [ Press [
] key. ] or [ ] Key.
. To t a l Coun t
0001720
0001723
3. If you press the [ * ] Key, one more upper digit flashes. Change the value in the same way.
. To t a l Coun t
0001723
. To t a l
Coun t
0001723
4. Press the [ENTER] key to decide the setting. The indication stops flashing when decided.
8-161
K105sm8e5_EUA
NOTE
It is impossible to select the sub mode if the key operation is locked.
2. Select each sub mode pressing the [MENU] key. The name of selected sub mode is indicated on the LCD. Status Indication (Normal Mode)
P r i n t e r Ready R1 : 36
Command Mode
( 4 ) Command
8-162
K105sm8e6_EUA
8-163
K105sm8e6_EUA
[ENTER] Key
Ro l l 1 S i z e 36
3. If you press [ ] and [ ] Keys, you can indicate either Roll 1 Size or Roll 2 Size on the LCD. You check the information about the Roll1 when Roll 1 Size is indicated, and you can check that of Roll 2 when Roll 2 Size is indicated. So select either Roll Deck of which information you will check.
Ro l l 1 S i z e 36
] and [
] Keys
Ro l l 2 S i z e 36
Roll 1 information
Roll 2 information
NOTE
You can indicate Roll 2 Size only when the machine is equipped with the Roll Deck 2.
8-164
K105sm8e6_EUA
4. After selecting the Roll Deck, press the [ * ] key several times to indicate the information about the selected Roll Deck. The LCD indicates Size (Width), Type and Remain (Remaining level of roll) orderly whenever you press the [ * ] Key.
Ro l l 1 S i z e 36
Press [ * ] key
Ro l l 1 T y p e Plai n
Press [ * ] key
Ro l l 1 Rema i n 75%
Press [ * ] key
Reference
(1) Each indication in Roll Remain means as follows. 100% From 100 to 75% 75% From 75 to 50% 50% From 50 to 10% 10% Smaller than 10% (2) The following messages are also indicated according to the situation. Machine is checking the paper.
Ro l l 1 Pape r Chec k
8-165
K105sm8e6_EUA
( 2 ) Se t t i ng Mode1
2. Press the [ENTER] key to enter the Setting Mode 1. The LCD initially indicates Roll 1 Type.
( 2 ) Se t t i ng Mode1
[ENTER] Key
Ro l l 1 T y p e Pl ai n
3. There are 2 setting items Roll Type and Roll Size in the Setting Mode, which you can specify for each Roll Deck 1 and 2 respectively. To specify the type of roll paper, indicate either Roll 1 Type or Roll 2 Type pressing the [ ] key and [ ] key.
Ro l l 1 T y p e Pl ai n
Ro l l 1 S i z e 36
[
Ro l l 2 T y p e Pl ai n
] key and [
] key
Ro l l 2 S i z e 36
8-166
K105sm8e6_EUA
4. Press the [ENTER] Key when you will change the paper type. The paper type indicated on the 2nd line starts flashing, which means now you can change the setting. [ENTER] Key
Ro l l 1 T y p e Pl ai n
Ro l l 1 T y p e Pl ai n
Ro l l 1 T y p e Pl ai n
] and [
] Keys
Ro l l 1 Ty p e T r ac i ng
NOTE
1 is indicated after the paper type if you press the [ * ] Key at this time. It means the special paper. (Tracing 1 in this example means Tracing paper of special paper.)
Ro l l 1 Ty p e T r ac i ng 1
6. Press the [ENTER] Key finally to decide the setting. The selected setting (Tracing in this example) stops flashing when decided. [ENTER] Key
Ro l l 1 Ty p e T r ac i ng
Ro l l 1 Ty p e T r ac i ng
8-167
K105sm8e6_EUA
( 2 ) Se t t i ng Mode1
2. Press the [ENTER] key to enter the Setting Mode 1. The LCD initially indicates Roll 1 Type.
( 2 ) Se t t i ng Mode1
[ENTER] Key
Ro l l 1 T y p e Pl ai n
3. There are 2 setting items Roll Type and Roll Size in the Setting Mode, which you can specify for each Roll Deck 1 and 2 respectively. To specify the size of roll paper, indicate either Roll 1 Size or Roll 2 Size pressing the [ ] key and [ ] key.
Ro l l 1 T y p e Pl ai n
Ro l l 1 S i z e 36
[
Ro l l 2 T y p e Pl ai n
] key and [
] key
Ro l l 2 S i z e 36
4. Press the [ENTER] Key when you will change the size setting. The size indicated on the 2nd line starts flashing, which means now you can change the setting. [ENTER] Key
Ro l l 2 S i z e 36
Ro l l 2 S i z e 36
8-168
K105sm8e6_EUA
] and [
] Keys, select the size of the roll paper installed on the concerning
Ro l l 2 S i z e 36
] and [
] Keys
Ro l l 2 S i z e 24
6. Press the [ENTER] Key finally to decide the setting. The selected setting (24 in this example) stops flashing when decided.
Ro l l 2 S i z e 24
[ENTER] Key
Ro l l 2 S i z e 24
8-169
K105sm8e6_EUA
2. Press the [ENTER] key to enter the Setting Mode 2. The LCD initially indicates Warm Sleep.
. Wa r m S l eep OFF
8-170
K105sm8e6_EUA
3. As there are 10 Sub Modes in the Setting Mode 2, select the necessary one pressing the [ ] and [ ] Key.
. Wa r m S l eep OFF
] and [
] Keys
L ow Temp Mo d e OFF
. Co l d S l eep OFF
. Fu l l OFF
I mage Mode
. Co l d S l eep T i me 10mi n
. Enhanc e OFF
. Au t o Powe r Of f OFF
. Smoo t h i ng OFF
. Powe r Of f 10mi n
T i me
. TR As s i s t L ED OFF
8-171
K105sm8e6_EUA
Reference
The purpose of Warm Sleep Mode is to reduce the power consumption by falling down the temperature of heater some degrees. The temperature of the heater unit is about 160 -170 degrees Centigrade when the KIP3000 is ready. But if no print job or copy job is sent for a long time, it is better for saving the power to fall down the temperature of heater. (Temperature is kept about 100 degrees Centigrade.) The Warm Sleep Mode will be cancelled automatically if only you send a print job or a copy job from the outer device. However, please understand it takes some minutes to recover from the Warm Sleep Mode because it is necessary to raise the temperature again up to about 160 - 170 degrees Centigrade. (Print starts when the KIP3000 gets ready.)
1. Select Warm Sleep in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
. Wa r m S l eep OFF
2. Switch between ON and OFF pressing the [ENTER] Key. The Warm Sleep Mode will work if you select ON.
. Wa r m S l eep OFF
[ENTER] Key
. Wa r m S l eep ON
8-172
K105sm8e6_EUA
Reference
The purpose of Warm Sleep Mode is to reduce the power consumption by falling down the temperature of heater some degrees. The temperature of the heater unit is about 160 -170 degrees Centigrade when the KIP3000 is ready. But if no print job or copy job is sent for a long time, it is better for saving the power to fall down the temperature of heater. (Temperature is kept about 100 degrees Centigrade.) The Warm Sleep Mode will be cancelled automatically if only you send a print job or a copy job from the outer device. However, please understand it takes some minutes to recover from the Warm Sleep Mode because it is necessary to raise the temperature again up to about 160 - 170 degrees Centigrade. (Print starts when the KIP3000 gets ready.) 1. Select Warm Sleep Time in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
2. Press the [ENTER] Key when you will change the timer setting. The value indicated on the 2nd line starts flashing, which means now you can change the setting.
.Wa rm S l eep T i me 10mi n
[ENTER] Key
3. Change the timer value pressing the [ ] and [ ] Keys. The setting range is from 10 minutes to 4 hours.
.Wa rm S l eep T i me 10mi n
] and [
] Keys
4. Press the [ENTER] Key finally to decide the timer setting. The timer value stops flashing when decided.
.Wa rm S l eep T i me 50mi n
[ENTER] Key
8-173
K105sm8e6_EUA
Reference
The purpose of Cold Sleep Mode is not to consume as much power as possible by shutting off supplying the power to the heater unit. It can save more power than Warm Sleep Mode. The temperature of the heater unit is about 160 - 170 degrees Centigrade when the KIP3000 is ready. But if the KIP3000 does not receive any print job or copy job for a long time, it is the best way for saving the power to stop supplying the power to the heater unit completely. The Cold Sleep Mode will be cancelled automatically if only you send a print job or a copy job from the outer device. However, please understand it takes a little long time to recover from the Cold Sleep Mode because it is necessary to raise the temperature again up to about 160 -170 degrees Centigrade. (Print starts when the KIP3000 gets ready.)
1. Select Cold Sleep in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
. Co l d S l eep OFF
2. Switch between ON and OFF pressing the [ENTER] Key. The Cold Sleep Mode will work if you select ON.
. Co l d S l eep OFF
[ENTER] Key
. Co l d S l eep ON
8-174
K105sm8e6_EUA
Reference
The purpose of Cold Sleep Mode is not to consume as much power as possible by shutting off supplying the power to the heater unit. It can save more power than Warm Sleep Mode. The temperature of the heater unit is about 160 - 170 degrees Centigrade when the KIP3000 is ready. But if the KIP3000 does not receive any print job or copy job for a long time, it is the best way for saving the power to stop supplying the power to the heater unit completely. The Cold Sleep Mode will be cancelled automatically if only you send a print job or a copy job from the outer device. However, please understand it takes a little long time to recover from the Cold Sleep Mode because it is necessary to raise the temperature again up to about 160 -170 degrees Centigrade. (Print starts when the KIP3000 gets ready.)
1. Select Cold Sleep Time in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
. Co l d S l eep T i me 10mi n
2. Press the [ENTER] Key when you will change the timer setting. The value indicated on the 2nd line starts flashing, which means now you can change the setting.
. Co l d S l eep T i me 10mi n
[ENTER] Key
. Co l d S l eep T i me 10mi n
3. Change the timer value pressing the [ ] and [ ] Keys. The setting range is from 10 minutes to 4 hours.
. Co l d S l eep T i me 10mi n
] and [
] Keys
. Co l d S l eep T i me 50mi n
4. Press the [ENTER] Key finally to decide the timer setting. The timer value stops flashing when decided.
. Co l d S l eep T i me 50mi n
[ENTER] Key
. Co l d S l eep T i me 50mi n
8-175
K105sm8e6_EUA
Reference
The Auto Power OFF is the function to switch off the KIP3000 automatically if no print job or copy job is sent for the time you have specified in advance (timer). If the KIP3000 is turned off by the Auto Power OFF, the operator needs to turn it on again pressing the Power Switch. (It is impossible to turn it on automatically.)
1. Select Auto Power Off in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
. Au t o Powe r Of f OFF
2. Switch between ON and OFF pressing the [ENTER] Key. The Auto Power OFF will work if you select ON.
. Au t o Powe r Of f OFF
[ENTER] Key
. Au t o Powe r Of f ON
8-176
K105sm8e6_EUA
Reference
The Auto Power OFF is the function to switch off the KIP3000 automatically if no print job or copy job is sent for the time you have specified in advance (timer). If the KIP3000 is turned off by the Auto Power OFF the operator needs to turn it on again pressing the Power Switch. (It is impossible to turn it on automatically.)
1. Select Power Off Time in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
. Powe r Of f 10mi n
T i me
2. Press the [ENTER] Key when you will change the timer setting. The value indicated on the 2nd line starts flashing, which means now you can change the setting.
. Powe r Of f 10mi n T i me
[ENTER] Key
. Powe r Of f 10mi n
T i me
3. Change the timer value pressing the [ ] and [ ] Keys. The setting range is from 10 minutes to 4 hours.
. Powe r Of f 10mi n T i me
] and [
] Keys
. Powe r Of f 50mi n
T i me
4. Press the [ENTER] Key finally to decide the timer setting. The timer value stops flashing when decided.
. Powe r Of f 50mi n T i me
[ENTER] Key
. Powe r Of f 50mi n
T i me
8-177
K105sm8e6_EUA
Reference
There may be the case that the print image looks so light (not so clear) although the density setting is proper or higher than required. This kind of problem may occur when the used printing paper is special, because it is difficult to transfer the toner image fully onto it. The Transfer Assist LED (Separation Lamp) is the solution for this kind of problem as it helps to transfer the toner image. Try to make it work if you feel the print image is so light. Transfer Assist LED is OFF. (Image looks not so clear.) Transfer Assist LED is ON. (Image looks clear with enough density.)
NOTE
You can specify to which type of paper the Transfer Assist LED (Separation Lamp) should work. It can be specified in the Service Mode. Refer to [8. 5. 4.36 Operation of Separation Lamp (No.067)] on the page 8-61.
1. Select TR Assist LED in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
. TR As s i s t L ED OFF
2. Switch between ON and OFF pressing the [ENTER] Key. The Transfer Assist LED will work if you select ON.
. TR As s i s t L ED OFF
[ENTER] Key
. TR As s i s t L ED ON
8-178
K105sm8e6_EUA
Reference
A diagonal line tends to look weaker than vertical one or horizontal one. The Smoothing function emphasizes the diagonal one so that it becomes as clear as vertical and horizontal ones. Smoothing function is OFF. (Diagonal line looks so weak.) Smoothing function is ON. (Diagonal line looks clear.)
1. Select Smoothing in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
. Smoo t h i ng OFF
2. Switch between ON and OFF pressing the [ENTER] Key. The Smoothing function is validated if you select ON.
. Smoo t h i ng OFF
[ENTER] Key
. Smoo t h i ng ON
8-179
K105sm8e6_EUA
Reference
An isolated dot image tends to look so weak. The Dot Enhancement function emphasizes the isolated dot so that it looks clear. (Dot Enhancement function emphasizes only the isolated dot. It will not emphasize the dots coming together some degree.) Dot Enhancement function is OFF. (Diagonal line looks so weak.) Dot Enhancement function is ON. (Diagonal line looks clear.)
NOTE
The Dot Enhancement function is validated if you select ON in the User Mode. At this time the Level (degree) of Dot Enhancement Function relies on the setting in the Service Mode. Refer to [8. 5. 4.23 Dot Enhancement Level (Dither) (No.052)] on the page 8-55 for this setting.
1. Select Enhance in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
. Enhanc e OFF
2. Switch between ON and OFF pressing the [ENTER] Key. The Dot Enhancement function is validated if you select ON.
. Enhanc e OFF
[ENTER] Key
. Enhanc e ON
8-180
K105sm8e6_EUA
Reference
Usually each print is compulsively provided with a trailing margin of 3mm long regardless of the image size. But the image can be printed even in the trailing margin area if you validate the Full Image Mode. Full Image Mode is OFF. (Print is provided with trailing margin.) Full Image Mode is OFF. (No trailing margin is provided.)
NOTE
The interval between each sheet of print becomes longer than usual if you validate the Full Image Mode, because it requires a cleaning operation between each sheet.
1. Select Full Image Mode in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
. Fu l l OFF
I mage Mode
2. Switch between ON and OFF pressing the [ENTER] Key. The Full Image Mode is validated if you select ON.
. Fu l l OFF I mage Mode
[ENTER] Key
. Fu l l ON
I mage Mode
8-181
K105sm8e6_EUA
Reference
The toner image may not be fixed firmly onto the paper if you make a copy or plot right after turning on the machine (in the morning especially) in very cold environment. But it is possible to avoid this kind of fusing problem by the Low Temperature Mode. It works as follows. 1. If both the center and sides of the Fuser Roller are colder than 30 degrees centigrade when you turn on the machine (or when you cancel the Sleep Mode), the Low Temperature Mode is validated. 2. The Fuser Roller is heated up to 10 degrees higher than the setting temperature. (If the setting temperature is 170 degrees, it is heated up to 180 degrees. (170+10)) When plain paper or tracing paper is selected, the roller is heated 5 degrees more. (The roller is heated up to 185 degrees in this example. (170+10+5)) 3. The machine does not get ready even if the Fuser Roller is heated up to 10 degrees higher than the setting temperature. Instead of that the Fuser Roller continues rotating for 360 seconds. (Setting temperature plus 10 degrees is kept during this period.) 4. When 360 seconds has passed, the machine gets ready.
1. Select Low Temp Mode in the Setting Mode 2. (Refer to [(1) Selection of each Sub Mode] on the page 8-170 how to select it.)
L ow Temp Mo d e OFF
2. Switch between ON and OFF pressing the [ENTER] Key. The Full Image Mode is validated if you select ON.
. L ow Temp Mo d e OFF
[ENTER] Key
L ow Temp Mo d e ON
8-182
K105sm8e6_EUA
Reference
The leading edge of the new roll media may be rough or folded. To straighten the leading edge easily, the KIP3000 has a convenient function called Initial Cut. If you select one roll media and make the Initial Cut, the leading part (210mm from the leading edge) of roll media is cut off. The leading edge of that roll media is straight after the Initial Cut.
2. Press the [ENTER] key to enter the Command Mode. The LCD indicates Initial Cut.
. Ini t i al Ro l l
Cu t
1 ( Ready )
8-183
K105sm8e6_EUA
3. Pressing the [ * ] Key, select either Roll 1 or Roll 2 to which you will make Initial Cut.
. Ini t i al Ro l l . Ini t i al Ro l l
Cu t
1 ( Ready )
[ * ] Key
Cu t
2 ( Ready )
4. Press the [ENTER] Key to make Initial Cut. The LCD indicates (Start) during the Initial Cut.
. Ini t i al Ro l l Cu t
1 ( Ready )
[ENTER] Key
. Ini t i al Ro l l
Cu t
1 (St a r t )
NOTE
The LCD indicates (- - - - -) is it is impossible to make Initial Cut by some reason like an error of machine.
. Ini t i al Ro l l Cu t 2 (- - - - - )
8-184
K105sm8e6_EUA
8.12
Scanner Utility
8.12. 1 Installation
NOTE
Below are the system requirements to operate Scanner Utility. Windows 2000 / XP operating system USB 2.0 support
2. Disconnect the USB Cable (4), and connect it to the USB Terminal to your service PC.
8-185
K105sm8e7_EUA
3. Turn on both the service PC and then the KIP 3000. [Found New Hardware Wizard] starts automatically. Click [Next].
Reference
KIP K105SK is shown as example in this section. K105SC is displayed for machines after S/N 10510001.
4. Select Search for a suitable driver for my device [recommended], and then click [Next].
Choose this.
8-186
K105sm8e7_EUA
5. Set the Tech CD disk to the CD-ROM drive. Select Specify Location and then click [Next].
Mark this. The drivers are located under the Drivers Scanner Utility / USB Drivers on the KIP Tech CD. 6. The following message is indicated when the necessary driver is found. Click [Next].
8-187
K105sm8e7_EUA
8-188
K105sm8e7_EUA
10. Open the Device Manager, and confirm that [KIP K105SK] is operating properly.
8-189
K105sm8e7_EUA
3. It is possible to specify the destination of installed program. Install the program to the suggested location, click [Next].
8-190
K105sm8e7_EUA
4. The Setup Program asks you of the Program Folder. Just click [Next] if you have nothing to change.
5. Program files are copied onto the hard drive. Wait until all files are copied
6. The following message is indicated when all files have been copied. Click [Finish] finally.
8-191
K105sm8e7_EUA
NOTE
To use the entire adjustment menu, follow the instruction below. (A command line option switch to be set.) (1) Open the properties panel for a Scanner Utility shortcut. (2) Add the following text to the end of a path name. (en quad)/Maintenance
8-192
K105sm8e7_EUA
8-193
K105sm8e7_EUA
These adjustments are very important because they are greatly related with the image quality.
Dark Light Before Calibration (Uneven inputs) [Necessary situation] Shading is required when; Machine installation After replacing; (1) CIS Assembly (2) CIS Controller Board (3) Data Controller Board (4) Gap Roller
NOTE
Shading adjustment should be performed with Shading Sheet (P/N: Z058300790, 10 sheets). 1 sheet of Shading Sheet is included in the KIP 3000 accessary. Keep it in safe custody. 8-194
K105sm8e8_EUA
[Operation] 1. Connect the scanner unit and the PC directly with the USB 2.0 Cable. 2. Start Scanner Utility. 3. Select [Calibration] under [Adjust].
4. At first it is required to calibrate all pixels. Select [All] and then click [Execute]. You will be asked to set the original.
8-195
K105sm8e8_EUA
NOTE
(1) One corner of the Shading Sheet is cut off. Set Shading Sheet so that the corner is on the left and on the front side of machine. (2) Handle Shading Sheet with great care. Keep it in safe custody for avoiding dirt, fold or tear.
6. Click [OK] after setting Shading Sheet, and the scanner reads it. It takes about 5 minutes to complete Shading adjustment.
7. When finished scanning, click [OK]. Click [Confirm] to check the result of Shading.
NOTE
The dialog the same as the former step 6 will appear again. Just click [OK] without removing Shading Sheet.
8-196
K105sm8e8_EUA
Scan image of Shading Sheet 9. Scrolling the image horizontally, check whether the density is even or not. If the density is even at every place, finish Shading clicking [Close]. There may be some place of which density is different from others as the following image. As this pixel is defective, it is necessary to calibrate it individually in the next step.
Defective pixel
8-197
K105sm8e8_EUA
NOTE
Sometimes the density may be different between left and right as the following image. This is not a problem but it is just the border of image blocks.
11. Move the pointer onto the scan image, and you will find a kind of red cursor.
defective pixel
8-198
K105sm8e8_EUA
12. Move the red cursor so that its vertical line matches the defective pixel and click it. The defective pixel is selected by this operation. If there are some more defective pixels, select them in the same way.
Match the vertical line to a defective pixel. 13. Click [Execute], and the selected defective pixel is compensated individually.
14. You will be asked to set the original again. Set Shading Sheet to the scanner and click [OK]. Check the result of Shading again. When finished, click [Close].
8-199
K105sm8e8_EUA
NOTE
Color Correction should be performed with Calibration Sheet (P/N: Z108300230, 10 sheets). 1 sheet of Calibration Sheet is included in the KIP 3000 accessary. Keep it in safe custody.
8-200
K105sm8e9_EUA
NOTE
Position Calibration Sheet in the centre of Original Table so that the numbers on Calibration Sheet are at the top.
6. Click [OK] after setting the original, and the scanner reads Calibration Sheet.
7. The scan image of Calibration Sheet is displayed. Click [Get]. When the pointer moves on to the scan image, it changes to a red cross cursor.
8-201
K105sm8e9_EUA
NOTE
No colour calibration is always applied to the scan image of [Scan] in order to get a new calibration. An existing colour calibration can be checked with the scan image of [Confirm]. 8. Click the 6 reference points where the following picture shows to read colour information on Calibration Sheet. Each reference point has a pair of markers. Align the cursor with the markers so that the cursor is placed on a reference point. And then click the point to set a reference point. Set the all the 6 reference point in the order shown below. red cross cursor match the cursor to the markers 6 reference points
markers
match them
Reference
You can enlarge the scan image by dragging with the right button of mouse. Press F2 Key when you would like to go back to the reduced image.
8-202
K105sm8e9_EUA
9. When finished the 6 clicks for the reference points, [Set] will be activated. Click [Set] to apply the reference points to the colour correction adjustment.
10. Click [Confirm]. Scan Calibration Sheet again. Check that the scan image and Calibration Sheet do not have extreme difference in colour between them. Click [Close] to finish.
8-203
K105sm8e9_EUA
Feed Distance is the solution for this phenomenon. It compares the actual original image and the scan image to know how much their lengths are different. Then Feed Distance calculates the best compensation (motor speed) automatically so that both images should become as long as each other. [Necessary situation] Feed Distance is required when; After replacing; (1) Drive Roller 1 (2) Drive Roller 2 (3) Gap Roller Also you need to check whether the Feed Distance is proper after replacing the following parts. (Please record the current setting value before the replacement and input the same value after the replacement.) (1) CIS Assembly (2) Data Controller Board
8-204
K105sm8e9_EUA
[Operation]
NOTE
Feeding Distance (and Position) adjustment should be performed with Target Sheet (P/N: Z058501590, 10 sheets). 1. Measure the actual distance between a point and c point on the far left area of original, and also between b point and d point on the far right area. Lets suppose that each distance is as follows. Between a point and c point (800) is 799.7mm Between b point and d point (800) is 799.8mm Target Sheet
a a b b
c 800
d 800
NOTE
There are some number of c point X and d point X on the Target Sheet. You can select any one, but better adjustment can be expected if you measure a longer distance.
2. Connect the scanner unit and the PC directly with the USB 2.0 Cable. 3. Start Scanner Utility.
8-205
K105sm8e9_EUA
4. Select [Adjust Feed Distance] from [Adjust]. The Adjust Feed Distance Dialog is indicated.
NOTE
(1) If [Adjust Feed Distance] does not appear, follow the instruction on the next page.
8-206
K105sm8e9_EUA
NOTE (Continued)
a) Open the properties panel for a Scanner Utility shortcut. b) Add the following text to the end of a path name. (en quad)/Maintenance
(2) We recommend you to record the current setting value of Feed Distance for the safety before starting the adjustment from the next step. Click [Current value], and the current setting value is indicated.
8-207
K105sm8e9_EUA
5. At first, input the actual distance between a point and c point in [Actual Distance], which you have measured at the former step 1.
6. Set the Target Sheet to the scanner unit, and then click [Scan].
7. A dialog to specify the scan settings is indicated. Simply click [Scan] to scan the Target Sheet. (You do not have to change any setting this time.)
8-208
K105sm8e9_EUA
8. The scan image of the Target Sheet is indicated in the screen of Scanner Utility.
Reference
You can enlarge the scan image by dragging with the right button of mouse. Press the F2 Key when you would like to go back to the reduced image.
NOTE
Make another scan for the top and bottom part of Target Sheet. Scan images for top and bottom part should not be used for Feeding Distance adjustment. 9. Indicate the enlarged image of a point on the screen, which was the measuring point at the former step 1.
8-209
K105sm8e9_EUA
10. Click the input window of [Theoretical Distance]. A red cursor appears on the screen.
8-210
K105sm8e9_EUA
12. Similarly indicate the enlarged image of c point and click the mouse at the measuring point.
13. Some value is indicated in [Theoretical Distance] according to 2 measuring points you specified at both steps 9 and 10. This value means the distance between a point and b point of the resulting scan image.
8-211
K105sm8e9_EUA
14. Click [Calculate]. The program automatically calculates the best compensation value considering the difference of Actual Distance and Theoretical Distance. The calculated compensation value (motor speed) is indicated in [Feed Adjustment Value].
15. Click [Set], and the calculated Feed Adjustment Value is validated.
8-212
K105sm8e9_EUA
16. It is necessary to check the balance of original feeding between left and right after validating the new setting. (Left side means a-c points side, and right side means b-d points side.) Repeat the former steps from 3 to 12 also for the right side (between b point and d point), and compare the values of Feed Adjustment Value between left (a-c points) and right (b-d points). You do not have to do anymore thing if the difference between left and right is within 0.2%. (within 0.2% means the difference of indicated values is within +/-20.) Please click [Close] without clicking [Set].
17. If the difference of the values of Feed Adjustment Value between left and right is larger than 0.2%, do as follows. a) Measure the actual distance between the center of a-b points and that of c-d points on the Target Sheet.
c 800 c 1000
c 1100 c 1150
Measure between these 2 points. b) Repeat the former steps from 3 to 12 for the center area. c) Click [Set] to validate the Value indicated in [Feed Adjustment Value].
8-213
K105sm8e9_EUA
8.12. 4. 4
Position (stitching)
[Purpose of Position (stitching)] The scanner part of KIP 3000 reads the image of original with 5 - CIS (Contact Image Sensor). As these CIS are arranged in 2 rows, there occurs a vertical gap of image among the image blocks. Also the reading area of these 5 pieces of CIS overlaps each other some degree. As a result there occurs the duplication of image between neighboring Image Block (same image is commonly included in the neighboring two Image Blocks).
Vertical gap of image Duplications of image Position is the solution for these kinds of phenomenon. It is possible remove the vertical gap of image by vertical positioning process (Y offset). And it is also possible to remove the duplication of image by horizontal positioning process (X overlap). [Necessary situation] Position is required when; After replacing; (1) CIS Assembly (2) Gap Roller Also you need to check whether or not the Feed Distance is proper after replacing the following part. (Please record the current setting value before the replacement and then input the same value after the replacement.) (1) Data Controller Board
8-214
K105sm8e9_EUA
[Operation]
NOTE
Position (and Feeding Distance) adjustment should be performed with Target Sheet (P/N: Z058501590, 10 sheets). 1. Connect the scanner unit and the PC directly with the USB 2.0 Cable. 2. Start Scanner Utility. 3. Select [Calibration] from [Adjust]. The Position Adjustment Dialog is indicated.
8-215
K105sm8e9_EUA
NOTE
(1) If [Adjust Position] does not appear, follow the instruction below.
a) Open the properties panel for a Scanner Utility shortcut. b) Add the following text to the end of a path name. (en quad)/Maintenance
8-216
K105sm8e9_EUA
NOTE (Continued)
(2) We recommend you to record the current setting values of Position for the safety before starting the adjustment from the next step. Click [Current value], and the current setting values are indicated.
4. Click [Default Value], and all setting value become default condition.
8-217
K105sm8e9_EUA
6. Set the Target Sheet to the scanner unit, and then click [Scan].
8-218
K105sm8e9_EUA
7. A dialog to specify the scan settings is indicated. Simply click [Scan] to scan the Target Sheet. (You do not have to change any setting this time.)
8. The scan image of the Target Sheet is indicated in the screen of Scanner Utility.
Reference
You can enlarge the scan image by dragging with the right button of mouse. Press the F2 Key when you would like to go back to the reduced image.
NOTE
Make another scan for the top and bottom part of Target Sheet. Scan images for top and bottom part should not be used for Position adjustment. 8-219
K105sm8e9_EUA
9. There will be 4 border lines of Image Blocks where you can find vertical gap of image and Duplication of image.
Border lines
Image Blocks You can integrate these Image Blocks correctly by specifying the same image included in both Image Blocks. (By selecting the same image, the program automatically calculates how much the image Block should be shifted vertically and horizontally.) Go to the next page for the adjustment. Same image included in both blocks. Image Blocks are integrated.
B078 B078 B079 B079 B078 B078 B078 B079 B079 B079
8-220
K105sm8e9_EUA
10. You need to adjust the position of 2-3 block and 3-4 block first, and then that of 1-2 block and 4-5 block. Click the input window X Overlap (or Y Offset) of 2-3 (or 3-4). A red cursor appears on the screen.
Clock the input window 11. Find the same image which is included in both Image Blocks. Same image
8-221
K105sm8e9_EUA
12. Move the red cursor onto the found image on one Image Block, and specify it clicking on it.
8-222
K105sm8e9_EUA
13. Also move the red cursor onto the same image on another Image Block, and specify it clicking on it.
8-223
K105sm8e9_EUA
14. Scanner Utility automatically calculates the best value for each X Overlap and Y Offset. Click [Check]. Setting value is automatically calculated.
15. Click [Set] to decide the setting value. A dialog pops up to requesting reload of document. Click [OK].
8-224
K105sm8e9_EUA
16. After deciding the new setting value, please scan the Target Sheet again and check the concerning border of Image Blocks. Confirm that the vertical gap of image and duplication of image are removed. (Before adjustment)
(After adjustment)
NOTE
If the scan image still has small vertical gap or duplication, change the setting value little by little with the key board. Change the value with key board.
8-225
K105sm8e9_EUA
17. Repeating the former steps from 10 to 15, adjust the positions of 2-3 block and 3-4 block first. Adjust them first.
8-226
K105sm8e9_EUA
18. Then adjust the positions of 1-2 block and 4-5 block. Adjust them later.
8-227
K105sm8e9_EUA
8-228
K105sm8e9_EUA
3. Select the Firmware component on the hard drive (or another drive). Click [Open].
NOTE
(1) A firmware file should be named K105sk_****.x. (2) Do not send any other data. Doing so results in Data Controller Board failure and requires its replacement. A firmware file for KIP 600 (KIP600_***.x) is incompatible with one for KIP 3000.
4. Confirm that the file name you will install is displayed. Click [Start].
File name 5. A dialog is displayed, which request you to turn off the KIP 3000. Turn off the machine.
8-229
K105sm8e9_EUA
8.13
Data Controller Board Assy (PW10522) contains a flash type memory to store the firmware for Engine Unit. It is possible to send and apply a new firmware by using an exclusive tool with a Windows PC. Before operation, please turn off KIP 3000. 1. Pull up Lever 2 (1) to open Engine Unit.
8-230
K105sm8eA
5. Connect RS Signal Cable to the connector (6: J201) on PW10522 PCB (7).
6. Connect the other end of RS Signal Cable (8) to any available COM port on your PC.
8-231
K105sm8eA
switch 1: ON switch 2: ON
Default
Download mode
NOTE
Before switching, be sure to turn off KIP 3000. 8. Run WriteFlash.exe. Flash Writing Tool screen is displayed.
8-232
K105sm8eA
11. Select a COM port that is being used for the communication in COM drop-down box.
8-233
K105sm8eA
12. Press [FILE] to locate a firmware file and open it. Program Size and Checksum will be displayed.
NOTE
Check your firmware version with its checksum before sending the file. Firmware Version 105X12B F 105X13B F 105X14B F 13. Turn on KIP 3000. 14. Press [DOWNLOAD] to start the process. Checksum 23B8AFB 236E810 22AF88A
8-234
K105sm8eA
NOTE
(1) Update may be failed if any of the following messages appear. Take necessary measures and retry the operation.
Message COM Port Open Error Cause Selected port is being used by an application Selected port does not exist RS Signal Cable is not connected to selected port Selected port does not support a given communication speed RS Signal Cable failure Measure Stop the application. Use any unoccupied port. Select the port been connecting. Select lower speed. Replace the cable.
Reception Error
(2) If an unexpected communication failure occurs during the process, the writing process will end abnormally. Retry the operation to overwrite the previous file. See step 8 and later.
16. Turn off KIP 3000. 17. Set DIP switch No.2 (9: DSW3, right) to OFF.
switch 1: ON switch 2: ON
9 Download mode 18. Remove RS Signal Cable. Return Cover 10, Cover 2 and Cover 3 in the original position. Default
8-235
K105sm8eA
Chapter 9 Appendix
K105sm9e1_EUA
Developer Unit (36,000m Maintenance)] according to the maintenance parts change. (page 5-11 to 5-32) 2. Comment for checking Scraper is added. (page 5-14) 3. Note column for tension adjustment on Timing Belt 480 for Roll 2 is changed. (Page 5-88) 4. Note column for tension adjustment on Timing Belt 480 for Roll 1 is changed. (Page 5-91) 5. Note column for tension adjustment on Timing Belt 753 is changed. (Page 5-94) 6. [5. 4.12 Removal of Roll Deck 2] is added. (page 5-123) 7. Note column for Grid Plate tension is changed. (page 5-186) 8. Comment for Transfer Corona adjustment is added. (page 5-194) 9. Description of Scan Glass Assembly is deleted due to supply system change of CIS unit. (page 5-253 to 5-259) 10. Note column for CIS Assembly classification is added. (page 5-253) 11. [5.12.6 Replacement of Gap Roller] is added. (page 5-260) Chapter 6 Maintenance 1. [Chapter 6 Field Service] is totally replaced with [Chapter 6 Maintenance]. Chapter 7 Troubleshooting 1. Comments for Delay, Stay, Early and Remained are added. (page 7-3) 2. Jam Code Remained (J-1004), (J-1006) and (J-1007) are added (page 7-5, 7-6). 3. Comments for designated voltage for Toner Roller Bias are added (page 7-20). 4. Note column for Transfer Colona adjustment is added. (page 7-20) 5. Scan Glass Assembly as a replacement part is changed to a whole CIS Unit. 6. [7.4 Touch Screen Calibration] is added. (page 7-40) Chapter 8 Service Mode & Utility Software 1. Sub UI and its location are illustrated. (page 8-6) 2. Default value for No.029, 030, 031, 038, 322, 323 and 324 are changed. (page 8-20, 8-27) 3. Drum Reverse Time (No.065) is added. (page 8-21, 8-59) 4. Transfer Voltage applied at 70mm from trailing edge is added. (page 8-33, 8-124) 5. Fuser Motor Speed applied at 30mm from trailing edge is added. (page 8-33, 8-124) 6. System requirement to run Scanner Utility is added. (page 8-172) 7. Note column for setting an option switch to Scanner Utility executable file is added. (page 8-179, 8-193, 8-203) 8. Part Number for Shading Sheet is added. (page 8-181) 9. [8.12.4.2 Calibration (color correction)] is added. (page 8-187) 10. Part Number for Target Sheet is added. (page 8-192, 8-201) 11. Note column for scanning Target Sheet is added. (page 8-196, 8-206)
(2)
K105smrec_EUA
1. Toner Supply Roller Bias (for both Print Cycle and Toner Collection Process) are changed according to the change of the Developer Unit. (Page 7-20) Chapter 8 Service Mode & Utility Software 1. Default setting value for the item number 028 (Developer Bias compensation - 1st Drum revolution) is changed from 155 to 0. (Pages 8-20 & 8-45) 2. In [8. 5 Adjustment Mode], setting items from 328 to 507 are newly added. (Pages from 8-27 to 8-33, and from 8-95 to 8-124) 3. [8.11 User Mode] is newly added. (Pages from 8-149 to 8-170) 4. Part Number of Target Sheet is described, which is used for Feed Distance and Position. (Pages 8-190 and 8-198) Chapter 9 Appendix 1. Electric Diagram for the print engine is modified according to the change of Developer Unit.
[5. 5. 2 How to fix the Aluminium Blocks] is newly added. (Page 5-143) NOTE Column is added. (Page 5-157) [5. 6. 2 LED focus adjustment] is newly added. (Pages from 5- 158 to 5-173) The height of the Image Corona Wire is changed from 13mm to 11mm. (Page 5-185) The height of the Transfer Corona Wire is changed from 11mm to 10mm. (Page 5-190) NOTE column is added stating the tension of Belt 1. (Page 5-207) NOTE column is added stating the tension of Belt 3. (Page 5-208) NOTE column is added stating the tension of Belt 1. (Page 5-210) As the mechanical construction of scanner unit is modified, some photographs in [5.12. 2 Replacement of Motor] are replaced. (Pages from 5-224 to 5-226) 17. As the mechanical construction of scanner unit is modified, some photographs in [5.12. 3 Replacement of Belt 60S2M250 and Belt 60S2M284] are replaced. (Pages from 5-227 to 5-229) 18. As the mechanical construction of scanner unit is modified, the way of disassembly described in [5.12. 4 Replacement of Drive Rollers 1 and 2] is changed. Also some photographs in this section are changed by the same reason. (Pages from 5-230 to 5-247) 19. As the mechanical construction of scanner unit is modified, the way of disassembly described in [5.12. 5 Replacement of CIS and Scan Glass Assemblies (L, C & R)] is changed. Also some photographs in this section are changed by the same reason. (Pages from 5-248 to 5-254) Chapter 7 Troubleshooting 1. Thermostat Error (E-005) is deleted. 2. The height of the Image Corona Wire is changed from 13mm to 11mm. (Page 7-20) 3. The height of the Transfer Corona Wire is changed from 11mm to 10mm. (Page 7-20) 4. Voltage of Toner Supply Roller Bias is changed. (Page 7-20) 5. Voltage of Cleaning Roller Bias is changed. (Page 7-20) 6. In [7. 2. 2. 1 Halftone is too light], Separation Lamp is added as the cause of problem. (Page 7-21) 7. In [7. 2. 2. 2 Halftone and solid black are too light], Contact point of Developer Bias is deleted because it is not related with this problem. Instead of it Dirt of LED Head is added. (Page 7-23) 8. In [7. 2. 2. 3 The whole image is extremely light], treatment for Paper is corrected. (Page 7-24) 9. In [7. 2. 2.10 Dirt on the back of the print], the order of Transfer Guides and Developer Unit is replaced. (Page 7-29) 10. In [7. 2. 2.15 Uneven image density (vertical), the description of Checking and Treatment for the item 4 (Installation of LED Head) is corrected. (Page 7-31) Chapter 8 Service Mode & Utility Software 1. In [8. 3 Information Mode], the information of Item No.01 and 02 is corrected. (Pages 8-11 & 8-12) 2. In [8. 4 Device Operation Mode], Signal Codes 30 (Cooling Fan Left) and 31 (Cooling Fan Center) are added. Also the target of Signal Code 19 becomes Cooling Fan Right. (Page 8-16) 3. Default setting values and setting ranges for many items are modified in [8. 5. 3 Setting Item list] (Pages from 8-19 to 8-26) 4. Item No.020, 021 & 036 of the Adjustment Mode are deleted (reserved). 5. [8. 5. 4.25 Switch timing of Toner Supply Roller Bias (No.054)] is newly added as the Item No.054 is added. (Page 8-48) 6. [8. 5. 4.34 Operation of Central Fuser Fan (No.063 & 064)] is newly added as Item No.063 & 064 are added. (Page 8-51) 7. [Transfer Assist Setting (No.067)] is renamed as [Operation of Separation Lamp (No.067)]. Also REFERENCE Column is added. (Page 8-52) 8. [8. 5. 4.77 Main Motor Speed (No.310 to 315)] is newly added as Item No.310 to 315 are added. (Page 8-87) 9. [8. 5. 4.78 Fuser Motor Speed (No.316 to 321)] is newly added as Item No.316 to 321 are (5)
K105smrec_EUA
added. (Page 8-87) 10. [8. 5. 4.79 Separation Corona OFF Timing (No.322 to 327)] is newly added as Item No.322 to 327 are added. (Page 8-87) Chapter 9 Appendix 1. Electric Diagram of the Engine Unit is modified because some electrical components are newly added. 2. Electric Diagram of the Scanner Unit is issued.
(6)
K105smrec_EUA