MATERIAL SAFETY DATA SHEET

SECTION 1 - PRODUCT & COMPANY IDENTIFICATION

UPL South Africa (Pty) Ltd Tel: 031 514 5600Co. Reg. No.: 2009/0

Product Name: Advanced Skin

Product Use: Fertilizer
Creation Date: June 2020
Revision Date: June 2023
24 Hr Emergency Number:
In case of Poisoning:
Griffon Poison Information Centre: 082 4468946
Poisons Information Helpline: 0861 555 777
In case of Spillage:
Spill Tech: 086 100 0366 / 083 253 6618

SECTION 2 - COMPOSITION / INFORMATION ON INGREDIENTS

Substance:
Sulphur (S) 450 g/L

Calcium (Ca) 156 g/L

Mixture: Components contained in the mixture is not classified as hazardous.
SECTION 3 - HAZARD IDENTIFICATION
Classification of the substance or mixture CLP Regulation (EC) no 1272/2008:
Not classified
Label elements
CLP Regulation (EC) no 1272/2008:
Hazard pictogram(s): None
Signal word: None
Hazardous statement(s): Non-Hazardous
Precautionary Statement(s):
P101 – If medical advice is needed, have product container or label at hand. P102 – Keep out of reach of children.
P103 – read label before use.
P501 – Dispose of the contents/containers in accordance with the current legislation on waste treatment.
Note: These precautionary statements are not prescribed by directive 1272/2008 as this product is not classified as hazardous under this dir
Other hazards

MATERIAL SAFETY DATA SHEET

Non-applicable
SECTION 4 - FIRST AID MEASURES AND PRECAUTIONS
Description of first aid measures
The symptoms resulting from intoxication can appear after exposure, therefore, in case of doubt, seek medical attention for direct exposure
chemical product or persistent discomfort, showing the SDS of this product.
By inhalation:
Remove to fresh air. If not breathing give artificial respiration. If breathing is difficult, give oxygen. Do NOT give mouth-to-mouth resusci
victim ingested or inhaled the substance. Keep person at rest and warm. Treat symptomatically and supportively as and when required.
Obtain medical advice if necessary.
By skin contact:
Remove any contaminated clothing. Wash skin with soap or mild detergent and water for at least 15 minutes. Get medical attention if irrita
develops or persists. Wash clothing before re-use.
By eye contact:
Immediately flush eyes with lukewarm water or saline solution for at least 15 minutes, lifting lower and upper eyelids occasionally. Check
remove any contact lenses after 5 minutes. Get medical attention if necessary.
By ingestion / aspiration:
Have victim rinse mouth thoroughly with water. Give water to dilute the material if victim is alert and not convulsing. Induce vomiting im
as directed by medical personnel. If spontaneous vomiting occurs, have victim lean forward with head down to avoid breathing in of vomit
mouth and administer more water. Never give anything by mouth to an unconscious person. Qualified medical personnel should perform
administration of oxygen. Seek medical advice if necessary.
Most important symptoms and effects, both acute and delayed
No information available.
Indication of any immediate medical attention and special treatment needed Notes to physician: None.
Specific treatments: Treat symptomatically.

SECTION 5 - FIRE-FIGHTING MEASURES

Fire Extinguishing Media Suitable extinguishing media:
Water spray, water fog, alcohol-resistant foam, carbon dioxide, dry chemical.
Unsuitable extinguishing media:
No information available.
Special hazards arising from the substance or mixture Hazards from the substance or mixture:
N/A
Hazardous thermal decomposition products:
Non known.
Additional provisions:
Act in accordance with the Internal Emergency Plan and the Information Sheets on actions to take after an accident or other emergencies. I
of a fire, wear full protective clothing and self-contained breathing apparatus with full-face piece operated in the pressure demand or other
pressure mode.

MATERIAL SAFETY DATA SHEET

SECTION 6 - ACCIDENTAL RELEASE MEASURES (SPILLAGE)
 Personal precautions, protective equipment and emergency procedures:
Slippery when spilt. Avoid accidents, clean up immediately. Wear appropriate personal protective equipment.
Environmental precautions:
Keep product away from drains, surface and underground water.
Methods and materials for containment and cleaning up Spills:
Collect in containers for disposal. Wash contaminated surfaces to remove any residues. Minimize use of water to prevent environmental
contamination.
Large Spills:
Prevent spillage or further leakage if it is safe to do so. Contain spillage with sand bags or by other means. Absorb with earth, sand or abso
material. Dig up heavily contaminated soil. Flush with water to remove any residues. Keep product and wash water out of drains, sewers, d
waterways.
Reference to other sections:
See Section 1 for emergency contact information.
See Section 8 for information on appropriate personal protective equipment. See Section 13 for additional waste treatment information.

SECTION 7 - HANDLING AND STORAGE REQUIREMENTS

Precautions for safe handling:
A.- Precautions for safe manipulation
Comply with the current legislation concerning the prevention of industrial risks. Keep containers hermetically sealed. Control spills and re
destroying them with safe methods (section 6). Avoid leakages from the container. Maintain order and cleanliness where dangerous produc
used.
B.- Technical recommendations for the prevention of fires and explosions
Due to its non-flammable nature, the product does not present a fire risk under normal conditions of storage, manipulation and use.
C.- Technical recommendations to prevent ergonomic and toxicological risks
Do not eat or drink during the process, washing hands afterwards with suitable cleaning products.
D.- Technical recommendations to prevent environmental risks
It is recommended to have absorbent material available at close proximity to the product (See subsection 6.3)
Conditions for safe storage, including any incompatibilities:
A.- Technical measures for storage Minimum Temp.: 5 °C Maximum Temp.: 30 °C Maximum time: 36 Months
B.- General conditions for storage
Store in the closed, original container in a dry, cool, well-ventilated area out of direct sunlight. Avoid sources of heat, radiation, static elect
contact with food. For additional information see subsection 10.5. Keep containers closed when not in use - check regularly for leaks.
Specific end use(s)
Except for the instructions already specified it is not necessary to provide any special recommendation regarding the uses of this product.

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET
SECTION 8 - EXPOSURE CONTROL/PERSONAL PROTECTION
Control parameters
No specific occupational exposure limit has been established.
 Exposure controls
Appropriate engineering controls:
Good general ventilation should be sufficient to control worker exposure to airborne contaminants.
Individual protection measures Hygiene measures:
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end o
working period.
Eye/face protection:
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure t
splashes, mists, gases or dusts. Possible: safety glasses with side- shields
Skin protection Hand protection:
Protective gloves against minor risks.
Body protection:
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be app
specialist before handling this product.
Other skin protection:
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks invol
should be approved by a specialist before handling this product.
Respiratory protection:
Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the s
respirator. Use a properly fitted, particulate filter respirator complying with an approved standard if a risk assessment indicates this is nece
both the product and its container. No significant release into the air is expected.
In accordance with the community legislation for the protection of the environment it is recommended to avoid environmental spillage

SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES

Appearance
Physical sate: Suspension Concentrate
Colour: Yellow
Odour: Pungent Odour
Volatility:
Boiling Point at atmospheric pressure: N/A
Vapour pressure at 20 °C: No significant volatility, aqueous liquid
Vapour pressure at 50 °C: No significant volatility, aqueous liquid
Evaporation rate 20 °C: No data available
Product description:
Density at 20 °C: 1.49 ± 0.02
Relative density at 20 °C: N/A
Dynamic viscosity at 20 °C: N/A
Kinematic viscosity at 20 °C: N/A

MATERIAL SAFETY DATA SHEET

 MATERIAL SAFETY DATA SHEET
OMPANY IDENTIFICATION
Tel: 031 514 5600Co. Reg. No.: 2009/019713/07

Advanced Skin
Fertilizer
June 2020
June 2023

re: 082 4468946

61 555 777

53 6618

/ INFORMATION ON INGREDIENTS

302 g/kg

105 g/kg
in the mixture is not classified as hazardous.
TIFICATION
nce or mixture CLP Regulation (EC) no 1272/2008:

2/2008:
one
None
Non-Hazardous

ed, have product container or label at hand. P102 – Keep out of reach of children.

ontainers in accordance with the current legislation on waste treatment.

ments are not prescribed by directive 1272/2008 as this product is not classified as hazardous under this directive.

MATERIAL SAFETY DATA SHEET

 SURES AND PRECAUTIONS
sures
oxication can appear after exposure, therefore, in case of doubt, seek medical attention for direct exposure to the
scomfort, showing the SDS of this product.

ing give artificial respiration. If breathing is difficult, give oxygen. Do NOT give mouth-to-mouth resuscitation if
bstance. Keep person at rest and warm. Treat symptomatically and supportively as and when required.
ry.

ng. Wash skin with soap or mild detergent and water for at least 15 minutes. Get medical attention if irritation
ng before re-use.

warm water or saline solution for at least 15 minutes, lifting lower and upper eyelids occasionally. Check for and
minutes. Get medical attention if necessary.

hly with water. Give water to dilute the material if victim is alert and not convulsing. Induce vomiting immediately
If spontaneous vomiting occurs, have victim lean forward with head down to avoid breathing in of vomits, rinse
r. Never give anything by mouth to an unconscious person. Qualified medical personnel should perform
medical advice if necessary.
nd effects, both acute and delayed

medical attention and special treatment needed Notes to physician: None.

eat symptomatically.

MEASURES
uitable extinguishing media:
esistant foam, carbon dioxide, dry chemical.
edia:

m the substance or mixture Hazards from the substance or mixture:

osition products:

al Emergency Plan and the Information Sheets on actions to take after an accident or other emergencies. In the event
hing and self-contained breathing apparatus with full-face piece operated in the pressure demand or other positive

MATERIAL SAFETY DATA SHEET

RELEASE MEASURES (SPILLAGE)
ctive equipment and emergency procedures:
ents, clean up immediately. Wear appropriate personal protective equipment.

surface and underground water.

ontainment and cleaning up Spills:
. Wash contaminated surfaces to remove any residues. Minimize use of water to prevent environmental

e if it is safe to do so. Contain spillage with sand bags or by other means. Absorb with earth, sand or absorbent
nated soil. Flush with water to remove any residues. Keep product and wash water out of drains, sewers, ditches and

:
tact information.
appropriate personal protective equipment. See Section 13 for additional waste treatment information.

D STORAGE REQUIREMENTS
ng:
ation
on concerning the prevention of industrial risks. Keep containers hermetically sealed. Control spills and residues,
ds (section 6). Avoid leakages from the container. Maintain order and cleanliness where dangerous products are

or the prevention of fires and explosions

the product does not present a fire risk under normal conditions of storage, manipulation and use.
o prevent ergonomic and toxicological risks
ocess, washing hands afterwards with suitable cleaning products.
o prevent environmental risks
bent material available at close proximity to the product (See subsection 6.3)
including any incompatibilities:
ge Minimum Temp.: 5 °C Maximum Temp.: 30 °C Maximum time: 36 Months
e
ainer in a dry, cool, well-ventilated area out of direct sunlight. Avoid sources of heat, radiation, static electricity and
information see subsection 10.5. Keep containers closed when not in use - check regularly for leaks.

y specified it is not necessary to provide any special recommendation regarding the uses of this product.

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET
NTROL/PERSONAL PROTECTION

e limit has been established.

ntrols:
be sufficient to control worker exposure to airborne contaminants.
res Hygiene measures:
horoughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the

n approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid
ossible: safety glasses with side- shields
tion:
isks.

r the body should be selected based on the task being performed and the risks involved and should be approved by a
oduct.

ditional skin protection measures should be selected based on the task being performed and the risks involved and
st before handling this product.

d on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected
particulate filter respirator complying with an approved standard if a risk assessment indicates this is necessary of
. No significant release into the air is expected.
y legislation for the protection of the environment it is recommended to avoid environmental spillage

D CHEMICAL PROPERTIES

Suspension Concentrate
Yellow
Pungent Odour

sure: N/A
No significant volatility, aqueous liquid
No significant volatility, aqueous liquid
No data available

1.49 ± 0.02
N/A
N/A
N/A

MATERIAL SAFETY DATA SHEET

 Kinematic viscosity at 40 °C: N/A
pH: 6.3
Vapour density at 20 °C: N/A Partition coefficient n-octanol/water at 20 °C: N/A Solubility in water at 20 °C:
N/A
Solubility properties: N/A
Decomposition temperature: N/A
Melting point/freezing point: N/A
Explosive properties: No explosive properties
Oxidizing properties: N/A
Flammability:
Flash point: N/A
Auto-ignition temperature: N/A
Lower flammability limit: N/A
Upper flammability limit: N/A
Other Information
No additional information.

SECTION 10 - STABILITY AND REACTIVITY

Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See section 7.
Chemical stability:
The product is stable under recommended storage conditions.
Possibility of hazardous reactions:
Hazardous polymerization does not occur.
Conditions to avoid:
Applicable for handling and storage at room temperature:

Shock & friction Contact with air Increase in temperature Sunlight

N/A N/A N/A N/A

Incompatible materials:
Acids Water Combustive materials Combustible Others
materials
N/A N/A N/A N/A N/A
Hazardous decomposition products:
N/A
SECTION 11 - TOXICOLOGICAL INFORMATION
Information on toxicological effects
No information available.
Dangerous health implications:
 Low ingestion hazard in normal use. Irritate respiratory passages very slightly. Direct contact may cause temporary redness and discomfort
Ingestion (acute effect):
- Acute toxicity: Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous for
effect.
- Corrosivity/Irritability: Based on available data, the classification criteria are not met, as it does not contain substances classified as dange
this effect.
B- Inhalation (acute effect):
- Acute toxicity: Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous for
effect.
- Corrosivity/Irritability: Based on available data, the classification criteria are not met, as it does not contain substances classified as dange
this effect.
C- Contact with the skin and the eyes (acute effect):
- Contact with the skin: Based on available data, the classification criteria are not met, as it does not contain substances classified as danger
this effect.
- Contact with the eyes: Based on available data, the classification criteria are not met, as it does not contain substances classified as dange
this effect.
D- CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
- Carcinogenicity: Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous f
effects mentioned.
- Mutagenicity: Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous for
effect.
- Reproductive toxicity: Based on available data, the classification criteria are not met, as it does not contain substances classified as dange
this effect.
E- Sensitizing effects:
- Respiratory: Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous with
sensitizing effects.
- Cutaneous: Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous for thi
F- Specific target organ toxicity (STOT)-time exposure:
Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous for this effect.
G- Specific target organ toxicity (STOT)-repeated exposure:
- Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria are not met, as it does not con
substances classified as dangerous for this effect.
- Skin: Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous for this effec
H- Aspiration hazard:
Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous for this effect.
Other information: Non-applicable

MATERIAL SAFETY DATA SHEET

SECTION 12 - ECOLOGICAL INFORMATION
Toxicity:
No information available.
MATERIAL SAFETY DATA SHEET
 °C: N/A Solubility in water at 20 °C:

age conditions. See section 7.

Humidity

N/A

Others

N/A
ct may cause temporary redness and discomfort. A.-

ot contain substances classified as dangerous for this

does not contain substances classified as dangerous for

ot contain substances classified as dangerous for this

does not contain substances classified as dangerous for

does not contain substances classified as dangerous for

does not contain substances classified as dangerous for

not contain substances classified as dangerous for the

contain substances classified as dangerous for this

does not contain substances classified as dangerous for

contain substances classified as dangerous with

ontain substances classified as dangerous for this effect.

ces classified as dangerous for this effect.

sification criteria are not met, as it does not contain

substances classified as dangerous for this effect.

ces classified as dangerous for this effect.

EET

EET
 Persistence and degradability:
N/A
Bio accumulative potential:
No bioaccumulation potential
Mobility in soil:
No information found.
Results of PBT and vPvB assessment:
No information found.
Other adverse effects:
N/A

SECTION 13 - DISPOSAL CONSIDERATION

The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any a
use-specific information provided in the Exposure Scenario(s).
Waste treatment methods Product
Methods of disposal:
The generation of waste should be avoided or minimized wherever possible. Significant quantities of waste product residues should not be
of via the foul sewer but processed in a suitable effluent treatment plant. Disposal of this product, solutions and any by-products should at
comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements.
Hazardous waste:
No information available.
Packaging
Methods of disposal:
The generation of waste should be avoided or minimised wherever possible. Waste packaging should be recycled. Incineration or landfill s
be considered when recycling is not feasible.
Special precautions:
This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not bee
or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilt material and runoff and contact with so
waterways, drains and sewers.

SECTION 14 - TRANSPORT INFORMATION

Land transport Inland waterway Sea Transport (IMDG)
(ADR/RID) transport (AND/ADNR)

UN Number Not regulated. Not regulated. Not regulated.

UN proper shipping name - - -
Uses in Section 1 should be consulted for any available

antities of waste product residues should not be disposed

oduct, solutions and any by-products should at all times
d any regional local authority requirements.

ng should be recycled. Incineration or landfill should only

n handling emptied containers that have not been cleaned

of spilt material and runoff and contact with soil,

Air Transport (ICAO- TI /

IATA-DGR)

Not regulated.
-
 MATERIAL SAFETY DATA SHEET
Transport hazard - - -
class(es)
Packing Group - - -
Environmental hazards - - -

Special precautions for No data available No data available No data available

user
Transport in bulk No data available No data available No data available
according to Annex II of
Marpol and IBC Code:

SECTION 15 - REGULATORY INFORMATION

Safety, health and environmental regulations/legislation specific for the substance or mixture:
Candidate substances for authorization under the Regulation (EC) 1907/2006 (REACH): Non-applicable Regulation (EC) 1005/2009, abou
substances that deplete the ozone layer: Non-applicable Active substances not included in Annex I under Regulation (EU) No 528/2012: N
applicable REGULATION (EU) No 689/2012, in relation to the import and export of hazardous chemical products: Non- applicable
Limitations to commercialization and the use of certain dangerous substances and mixtures (Annex XVII REACH, etc
Non-applicable
Other legislation:
Law No.360 / 2003 on the dangerous substances and preparations
Law nr.349 / 2007 regarding the reorganization of the institutional framework for chemicals management Law no.249 / 2011 to amend arti
Law nr.349 / 2007 on the reorganization of the institutional framework chemicals management
Government Decision no. 477/2009 on the establishment of penalties for infringements of the provisions of Regulation (EC) No 1.907 / 20
of the European Parliament and of the Council concerning the Registration, Evaluation, Authorization and Restriction of Chemicals (REAC
establishing a European Chemicals Agency, amending Directive 1999/45 / EC and repealing Regulation (EEC) No. 793/93 and Regulation
1.488 / 94 Commission and Council Directive 76/769 / EEC and Directives 91/155 / EEC, 93/67 / EEC, 93/105 / EC and 2000/21 / EC Co
Law no.254 / 2011 amending article 26 of Law No.360 / 2003 on the preparations and substances dangerous GD nr.662 / 2011 repealing G
Decision no. 347/2003 regarding restrictions on the marketing and use of certain dangerous substances and preparations.
Emergency Ordinance no.60 / 2013 for completing art. 4 para. (1) of Law no. 349/2007 on the reorganization framework institutional man
of chemicals GD Nr.1408 / 2008 and Annexes 1-6 on classification, packaging and labelling of dangerous substances GD nr.937
/ 2010 and Annexes 1 to 5 on the classification, packaging and labelling in the marketing of dangerous preparations
GD no.122 / 2010 on the penalties applicable to infringements of the provisions of Regulation (EC) no.1272 / 2008 on classification, labell
packaging of substances and mixtures, amending and repealing Directives 67/548 / EEC and 1999/45 / EC, and amending Regulation (EC)
2006
GD no.398 / 2010 establishing measures to enforce the provisions of Regulation (EC) nr.1272 / 2008 on classification, labelling and packa
substances and mixtures.
Decision no. 1218/2006 establishing minimum safety requirements for ensuring occupational health and protection workers from risks rela
chemical agents.
Law no. 319/2006 - Law on safety and health at work
GD 621/2005 on the management of packaging and packaging waste.
GD 1872/2006 amending and supplementing Government Decision 621/2005 on the management of packaging and packaging waste The W
Regulations 2011, 2011 No. 988.
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as data used in a risk evaluation of the local circumstances in or
establish the necessary risk prevention measures for the manipulation, use, storage and disposal of this product.
Chemical Safety Assessment:

MATERIAL SAFETY DATA SHEET

The supplier has not carried out evaluation of chemical safety.
MATERIAL SAFETY DATA SHEET
SECTION 16 - OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with ANNEX II-Guide to the compilation of safety data sheets of Regulation (EC) N
1907/2006 (Regulation (EU) No 453/2010, Regulation (EC) No 2015/830)
Modifications related to the previous security card which concerns the ways of managing risks.:
Non-applicable
Texts of the legislative phrases mentioned in section 2:
Non-applicable
Texts of the legislative phrases mentioned in section 3:
Non-applicable.
CLP Regulation (EC) no 1272/2008:
Non-applicable

Classification procedure:Non-applicableAdvice related to training:Minimal training is recommended to prevent industrial risks for staff usi

MATERIAL SAFETY DATA SHEET

Notice to reader
DISCLAIMER AND LIMITATION OF LIABILITY
The information and recommendations contained in this Safety Data Sheet ("SDS") relate only to the specific material referred to herein (th
"Material") and do not relate to the use of such Material in combination with any other material or process. The information a
recommendations contained herein are believed to be current and correct as of the date of this SDS. HOWEVER, THE INFORMATION A
RECOMMENDATIONS ARE PRESENTED WITHOUT WARRANTY, REPRESENTATION OR LICENSE OF ANY KIND, EXPRES
IMPLIED, WITH RESPECT TO THEIR ACCURACY, CORRECTNESS OR COMPLETENESS, AND THE SELLER, SUPPLIE
MANUFACTURER OF THE MATERIAL AND THEIR RESPECTIVE AFFILIATES (COLLECTIVELY, THE "SUPPLIER") DISCLA
LIABILITY FOR RELIANCE ON SUCH INFORMATION AND RECOMMENDATIONS.
This SDS is not a guarantee of safety. A buyer or user of the Material (a "Recipient") is responsible for ensuring that it has all current infor
necessary to safely use the Material for its specific purpose.
EET
-

-
-

No data available

No data available

tance or mixture:
on-applicable Regulation (EC) 1005/2009, about
Annex I under Regulation (EU) No 528/2012: Non-
dous chemical products: Non- applicable
es and mixtures (Annex XVII REACH, etc ):

management Law no.249 / 2011 to amend article 4 of

ent
he provisions of Regulation (EC) No 1.907 / 2006
horization and Restriction of Chemicals (REACH),
g Regulation (EEC) No. 793/93 and Regulation (EC) no.
93/67 / EEC, 93/105 / EC and 2000/21 / EC Commission
ances dangerous GD nr.662 / 2011 repealing Government
substances and preparations.
the reorganization framework institutional management
g of dangerous substances GD nr.937
dangerous preparations
on (EC) no.1272 / 2008 on classification, labelling and
d 1999/45 / EC, and amending Regulation (EC) no.1907 /

72 / 2008 on classification, labelling and packaging of

al health and protection workers from risks related to

ement of packaging and packaging waste The Waste

risk evaluation of the local circumstances in order to

osal of this product.

EET

EET
lation of safety data sheets of Regulation (EC) No

of managing risks.:

mmended to prevent industrial risks for staff using this product, in order to facilitate their comprehension and interpretation of this safety data sheet, as we

EET
 nly to the specific material referred to herein (the
other material or process. The information and
is SDS. HOWEVER, THE INFORMATION AND
ION OR LICENSE OF ANY KIND, EXPRESS OR
LETENESS, AND THE SELLER, SUPPLIER AND
OLLECTIVELY, THE "SUPPLIER") DISCLAIM ALL
S.
ponsible for ensuring that it has all current information