10G SFP+ Transceiver

SFP-10G-SR-T01#141002
Product Specification
Product 10G SFP+ Transceiver
Model SFP-10G-SR-T01
File No. SFP-10G-SR-T01#141002
Version 1.0
Issuing Date 2020-6-4
Specification Revision Record

Date Version Page Revision Description Prepare Approve
20200930 1.0 Liu YM
All right reserved by Guilin GLsun Science and Tech Group Co., LTD. Without written permission,
-1-
any unit or individual can’t reproduce, copy or use it for any commercial purpose.
Guilin GLsun Science and Tech Group Co., LTD.

-1-
Tel: +86-773-3116006 info@glsun.com Web: www.glsun.com
SFP-10G-SR-T01#141002
Product Description
Small Form Factor Pluggable (SFP+) transceivers are compatible with SFF-8431,SFF-8432 and support
10G Ethernet SR and 10G Fibre Channel .It is designed for use in 10G-Gigabit multi-rate links up to 300m
of OM3 . Digital diagnostics functions are available via a 2-wire serial interface, as specified in SFF-8472.
Product Feature
Duplex LC connector
Hot-pluggable SFP footprint
Uncooled 850nm VCSEL laser
RoHS compliant and Lead Free
Distance up to 300m on 50/125um MMF
Metal enclosure for lower EMI
Low power dissipation <1.0W
Commercial and industrial operating temperature optional
SFP MSA SFF-8472 SFF-8431 SFF-8432 Compliant
Application
10GBASE-SR/SW
10G Fibre Channel
Regulatory Compliance
ESD to the Electrical PINs: compatible with MIL-STD-883 Method 3015

ESD to the Duplex LC Receptacle: compatible with EN 61000-4-2
Immunity compatible with EN 61000-4-3
EMI compatible with FCC Part 15 Class B
Laser Eye Safety compatible with FDA 21CFR 1040.10 and 1040.11 IEC 60950, IEC60825-1,2
RoHS compliant with RoHS 2.0(2015/863/EU)-amending.
Absolute Maximum Ratings
Parameter Symbol Min Typ Max Unit Ref.
Maximum Supply Voltage Vcc -0.5 +4.0 V
Storage Temperature TS -40 +85 °C
Operating Humidity RH 0 85 %

-2-
SFP-10G-SR-T01#141002
Recommended Operating Conditions
Power Supply Voltage Vcc 3.13 3.30 3.47 V
Power Supply Current Icc 300 mA Commercial
Tc 0 +70 °C Commercial
Case Operating Temperature
Tc -40 +85 °C Industrial
Data Rate Br 10.3 Gbps
9/125um G652 SMF Lmax - - 300 m
Electrical Characteristics
Transmitter
Input differential impedance Rin 80 100 120 Ω 1
Differential data input swing Vin, pp 120 - 850 mV
TX Disable-High - Vcc-0.8 - Vcc V
TX Disable-Low - Vee - Vee+0.8 V
TX Fault-High - Vcc-0.8 - Vcc V
TX Fault-Low - Vee - Vee+0.8 V
Receiver
Differential data output swing Vout, pp 300 - 850 mV 2
Data output rise time Tr 28 ps 3
Data output fall time Tf 28 ps 3
LOS-High - Vcc-0.8 Vcc V
LOS-Low - Vee Vee+0.8 V

Notes:
1. AC coupled.
2. Into 100 ohm differential termination.
3. 20-80%.

-3-
SFP-10G-SR-T01#141002
Optical Characteristics
Transmitter
Output Opt. Power PO -7.3 -1 dBm
Optical wavelength λ 840 850 860 nm
RMS Spectral Width (-20dB) Δλ 0.45 nm
Optical Extinction Ratio ER 3.5 dB

Transmitter and Dispersion
TDP 3.9 dB
Penalty
Receiver
Rx Sensitivity @ 10.3Gb/s SENS1 -9.95 dBm 1

Receiver Sensitivity OMA@
SENS2 -11.1 dBm 2
10.3Gb/s
Receiver Overload 1 - - dBm
Optical Center Wavelength λC 840 860 nm
LOS De-Assert LOSD - -13 dBm
LOS Assert LOSA -30 - dBm
LOS Hysteresis 0.5 5 dBm

Notes:
1.Measured with conformance signals defined in FC-PI-2 Rev. 10.0 specifications.
2.Measured with PRBS 231-1 at 10-12BER.
Pin Descriptions
Pin Symbol Name Ref.
1 VeeT Transmitter Ground (Common with Receiver Ground) 1
2 TX Fault Transmitter Fault. LVTTL-O 2

Transmitter Disable. Laser output disabled on high or open.
3 TX Disable 3
LVTTL-I
2-Wire Serial Interface Data Line (Same as MOD-DEF2 in
4 SDA 2
INF-8074i). LVTTL-I/O
2-Wire Serial Interface Data Line (Same as MOD-DEF2 in
5 SCL 2
INF-8074i). LVTTL-I
6 Mod_ABS Module Absent, Connect to VeeT or VeeR in Module. 2
Rate Select 0, optionally controls SFP+ module receiver .
7 RS0 4
LVTTL-I
-4-
SFP-10G-SR-T01#141002
Loss of Signal indication. Logic 0 indicates normal operation.
8 LOS 5
LVTTL-O
Rate Select 1, optionally controls SFP+ module transmitter.
9 RS1 4
LVTTL-I
10 VeeR Receiver Ground (Common with Transmitter Ground) 1
12 RD- Receiver Inverted DATA out. AC Coupled. CML-O
13 RD+ Receiver Non-inverted DATA out. AC Coupled. CML-O
15 VccR Receiver Power Supply 6
16 VccT Transmitter Power Supply 6
18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. CML- I
19 TD- Transmitter Inverted DATA in. AC Coupled. CML- I

Notes:
1. Circuit ground is internally isolated from chassis ground.
2. TX Fault is an open collector/drain output .Which should be pulled up with a 4.7K – 10K Ohms resistor
on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc+0.3V.A high output
indicates a transmitter fault caused by either the tx bias current or the tx output power exceeding the preset
alarm thresholds. A low output indicates normal operation .In the low state, the output is pulled to <0.8V.
3. Laser output disabled on TX Disable >2.0V or open, enabled on TX Disable<0.8V.
4. Internally pulled down per SFF-8431 Rev4.1.
5. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage
between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
6. Internally connected

-5-
SFP-10G-SR-T01#141002
Pin-out of Connector Block on Host Board
Recommend Circuit Schematic

-6-
SFP-10G-SR-T01#141002
Mechanical Specifications
Small Form Factor Pluggable (SFP28) transceivers are compatible with the dimensions defined by the SFP
Multi-Sourcing Agreement (MSA) , dimensions are in mm.
EEPROM Information
EEPROM memory map specific data field description is as below:

-7-
SFP-10G-SR-T01#141002
Digital Diagnostic Monitoring Interface
Five transceiver parameter values are monitored. The following table defines the monitored parameter’s
accuracy.
Parameter Range Accuracy Calibration

0 to +70°C
Temperature ±3°C Internal
-40 to +85°C
Voltage 2.97 to 3.63V ±3% Internal
Bias Current 0 to 100mA ±10% Internal
Rx Power -5 to -1 dBm ±3dB Internal
Tx Power -11.1 to -1 dBm ±3dB Internal
Ordering Information
Part Number Operating Case temperature DDMI
SFP-10G-SR-T01 Commercial (0~70℃) Yes

-8-

10G SFP+ Transceiver

Uploaded by

Copyright:

Available Formats

10G SFP+ Transceiver

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

10G SFP+ Transceiver

Uploaded by

Copyright:

Available Formats

SFP-10G-SR-T01#141002

Product 10G SFP+ Transceiver

File No. SFP-10G-SR-T01#141002

Issuing Date 2020-6-4

Specification Revision Record

20200930 1.0 Liu YM

Guilin GLsun Science and Tech Group Co., LTD.

ESD to the Electrical PINs: compatible with MIL-STD-883 Method 3015

Absolute Maximum Ratings

Parameter Symbol Min Typ Max Unit Ref.

Maximum Supply Voltage Vcc -0.5 +4.0 V

Storage Temperature TS -40 +85 °C

Guilin GLsun Science and Tech Group Co., LTD.

Recommended Operating Conditions

Parameter Symbol Min Typ Max Unit Ref.

Power Supply Voltage Vcc 3.13 3.30 3.47 V

Power Supply Current Icc 300 mA Commercial

Data Rate Br 10.3 Gbps

9/125um G652 SMF Lmax - - 300 m

Parameter Symbol Min Typ Max Unit Ref.

Input differential impedance Rin 80 100 120 Ω 1

Differential data input swing Vin, pp 120 - 850 mV

TX Disable-High - Vcc-0.8 - Vcc V

TX Disable-Low - Vee - Vee+0.8 V

TX Fault-High - Vcc-0.8 - Vcc V

TX Fault-Low - Vee - Vee+0.8 V

Differential data output swing Vout, pp 300 - 850 mV 2

Data output rise time Tr 28 ps 3

Data output fall time Tf 28 ps 3

LOS-High - Vcc-0.8 Vcc V

LOS-Low - Vee Vee+0.8 V

Guilin GLsun Science and Tech Group Co., LTD.

Parameter Symbol Min Typ Max Unit Ref.

Output Opt. Power PO -7.3 -1 dBm

Optical wavelength λ 840 850 860 nm

RMS Spectral Width (-20dB) Δλ 0.45 nm

Optical Extinction Ratio ER 3.5 dB

Rx Sensitivity @ 10.3Gb/s SENS1 -9.95 dBm 1

Optical Center Wavelength λC 840 860 nm

LOS De-Assert LOSD - -13 dBm

LOS Assert LOSA -30 - dBm

LOS Hysteresis 0.5 5 dBm

Pin Symbol Name Ref.

1 VeeT Transmitter Ground (Common with Receiver Ground) 1

2 TX Fault Transmitter Fault. LVTTL-O 2

11 VeeR Receiver Ground (Common with Transmitter Ground) 1

12 RD- Receiver Inverted DATA out. AC Coupled. CML-O

13 RD+ Receiver Non-inverted DATA out. AC Coupled. CML-O

14 VeeR Receiver Ground (Common with Transmitter Ground) 1

15 VccR Receiver Power Supply 6

16 VccT Transmitter Power Supply 6

17 VeeT Transmitter Ground (Common with Receiver Ground) 1

18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. CML- I

19 TD- Transmitter Inverted DATA in. AC Coupled. CML- I

20 VeeT Transmitter Ground (Common with Receiver Ground) 1

Guilin GLsun Science and Tech Group Co., LTD.

Pin-out of Connector Block on Host Board

Recommend Circuit Schematic

Guilin GLsun Science and Tech Group Co., LTD.

EEPROM memory map specific data field description is as below: